Table of Contents
- Alienware 17 Service Manual
- Before working inside your computer
- After working inside your computer
- Removing the base panel
- Replacing the base panel
- Removing the memory modules
- Replacing the memory modules
- Removing the solid-state drives
- Replacing the solid-state drives
- Removing the hard drive
- Replacing the hard drive
- Removing the palm rest
- Replacing the palm rest
- Removing the power-button board
- Replacing the power-button board
- Removing the status-light board
- Replacing the status-light board
- Removing the keyboard
- Replacing the keyboard
- Removing the touch pad
- Replacing the touch pad
- Removing the display assembly
- Replacing the display assembly
- Removing the battery
- Replacing the battery
- Removing the I/O board
- Replacing the I/O board
- Removing the speakers
- Replacing the speakers
- Removing the front AlienFX LED boards
- Replacing the front AlienFX LED board
- Removing the processor fan
- Replacing the processor fan
- Removing the system board
- Replacing the system board
- Removing the wireless card
- Replacing the wireless card
- Removing the heat sink
- Replacing the heat sink
- Removing the coin-cell battery
- Replacing the coin-cell battery
- Removing the video-card fan
- Replacing the video-card fan
- Removing the power-adapter port
- Replacing the power-adapter port
- Removing the subwoofer
- Replacing the subwoofer
- Removing the display bezel
- Replacing the display bezel
- Removing the display panel
- Replacing the display panel
- Removing the display hinges
- Replacing the display hinges
- Removing the computer base
- Replacing the computer base
- Removing the logo board
- Replacing the logo board
- Removing the camera
- Replacing the camera
- Removing the display-panel AlienFX LEDs
- Replacing the display-panel AlienFX LEDs
- Removing the Alienware AlienHead LED board
- Replacing the Alienware AlienHead LED board
- Removing the display back-cover
- Replacing the display back-cover
- BIOS setup program
- Flashing the BIOS
- Getting help and contacting Alienware
Alienware 17 R3 User Manual
Displayed below is the user manual for 17 R3 by Alienware which is a product in the Notebooks category. This manual has pages.
Related Manuals
Alienware 17
Service Manual
Computer Model: Alienware 17 R3
Regulatory Model: P43F
Regulatory Type: P43F001
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use
of your computer.
CAUTION: A CAUTION indicates either potential damage to
hardware or loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.
Copyright © 2015 Dell Inc. All rights reserved. This product is protected by U.S. and
international copyright and intellectual property laws. Dell™ and the Dell logo are trademarks of
Dell Inc. in the United States and/or other jurisdictions. All other marks and names mentioned
herein may be trademarks of their respective companies.
2015 - 08
Rev. A00
Contents
Before working inside your computer........................ 12
Before you begin ............................................................................................... 12
Safety instructions............................................................................................ 12
Recommended tools..........................................................................................13
After working inside your computer........................... 14
Removing the base panel................................................. 15
Procedure...........................................................................................................15
Replacing the base panel.................................................. 17
Procedure........................................................................................................... 17
Removing the memory modules................................... 18
Prerequisites......................................................................................................18
Procedure...........................................................................................................18
Replacing the memory modules.................................. 20
Procedure..........................................................................................................20
Post-requisites...................................................................................................21
Removing the solid-state drives.................................. 22
Prerequisites..................................................................................................... 22
Procedure.......................................................................................................... 22
Replacing the solid-state drives.................................. 24
Procedure..........................................................................................................24
Post-requisites..................................................................................................24
3
Removing the hard drive..................................................25
Prerequisites.....................................................................................................25
Procedure..........................................................................................................25
Replacing the hard drive.................................................. 28
Procedure..........................................................................................................28
Post-requisites..................................................................................................28
Removing the palm rest................................................... 29
Prerequisites.....................................................................................................29
Procedure..........................................................................................................30
Replacing the palm rest....................................................36
Procedure..........................................................................................................36
Post-requisites..................................................................................................36
Removing the power-button board............................ 37
Prerequisites..................................................................................................... 37
Procedure.......................................................................................................... 37
Replacing the power-button board............................ 39
Procedure..........................................................................................................39
Post-requisites..................................................................................................39
Removing the status-light board................................ 40
Prerequisites.....................................................................................................40
Procedure..........................................................................................................40
Replacing the status-light board................................. 42
Procedure..........................................................................................................42
Post-requisites..................................................................................................42
4
Removing the keyboard...................................................43
Prerequisites.....................................................................................................43
Procedure..........................................................................................................43
Replacing the keyboard....................................................47
Procedure.......................................................................................................... 47
Post-requisites.................................................................................................. 47
Removing the touch pad..................................................48
Prerequisites.....................................................................................................48
Procedure..........................................................................................................49
Replacing the touch pad....................................................51
Procedure...........................................................................................................51
Post-requisites.................................................................................................. 51
Removing the display assembly...................................52
Prerequisites.....................................................................................................52
Procedure..........................................................................................................52
Replacing the display assembly...................................56
Procedure..........................................................................................................56
Post-requisites.................................................................................................. 57
Removing the battery....................................................... 58
Prerequisites.....................................................................................................58
Procedure..........................................................................................................58
Replacing the battery.........................................................61
Procedure...........................................................................................................61
Post-requisites.................................................................................................. 61
5
Removing the I/O board....................................................62
Prerequisites.....................................................................................................62
Procedure..........................................................................................................62
Replacing the I/O board.................................................... 64
Procedure..........................................................................................................64
Post-requisites..................................................................................................64
Removing the speakers....................................................65
Prerequisites.....................................................................................................65
Procedure..........................................................................................................65
Replacing the speakers.................................................... 68
Procedure..........................................................................................................68
Post-requisites................................................................................................. 68
Removing the front AlienFX LED boards.................. 69
Prerequisites.....................................................................................................69
Procedure..........................................................................................................69
Replacing the front AlienFX LED board...................... 71
Procedure........................................................................................................... 71
Post-requisites...................................................................................................71
Removing the processor fan.......................................... 72
Prerequisites..................................................................................................... 72
Procedure.......................................................................................................... 72
Replacing the processor fan...........................................74
Procedure.......................................................................................................... 74
Post-requisites.................................................................................................. 74
6
Removing the system board.......................................... 75
Prerequisites..................................................................................................... 75
Procedure.......................................................................................................... 75
Replacing the system board...........................................79
Procedure.......................................................................................................... 79
Post-requisites..................................................................................................79
Removing the wireless card............................................ 81
Prerequisites......................................................................................................81
Procedure...........................................................................................................81
Replacing the wireless card............................................83
Procedure..........................................................................................................83
Post-requisites................................................................................................. 84
Removing the heat sink....................................................85
Prerequisites.....................................................................................................85
Procedure..........................................................................................................85
Replacing the heat sink.....................................................87
Procedure.......................................................................................................... 87
Post-requisites..................................................................................................87
Removing the coin-cell battery.................................... 88
Prerequisites.....................................................................................................88
Procedure..........................................................................................................88
Replacing the coin-cell battery.....................................90
Procedure..........................................................................................................90
Post-requisites................................................................................................. 90
7
Removing the video-card fan..........................................91
Prerequisites......................................................................................................91
Procedure...........................................................................................................91
Replacing the video-card fan......................................... 93
Procedure..........................................................................................................93
Post-requisites..................................................................................................93
Removing the power-adapter port............................. 94
Prerequisites.....................................................................................................94
Procedure..........................................................................................................94
Replacing the power-adapter port..............................96
Procedure..........................................................................................................96
Post-requisites..................................................................................................96
Removing the subwoofer.................................................97
Prerequisites..................................................................................................... 97
Procedure.......................................................................................................... 97
Replacing the subwoofer................................................. 99
Procedure..........................................................................................................99
Post-requisites..................................................................................................99
Removing the display bezel......................................... 100
Prerequisites...................................................................................................100
Procedure........................................................................................................100
Replacing the display bezel.......................................... 105
Procedure........................................................................................................ 105
Post-requisites................................................................................................105
8
Removing the display panel......................................... 106
Prerequisites................................................................................................... 106
Procedure........................................................................................................ 106
Replacing the display panel..........................................109
Procedure........................................................................................................ 109
Post-requisites................................................................................................109
Removing the display hinges........................................110
Prerequisites....................................................................................................110
Procedure......................................................................................................... 110
Replacing the display hinges........................................ 113
Procedure......................................................................................................... 113
Post-requisites.................................................................................................113
Removing the computer base...................................... 114
Prerequisites.................................................................................................... 114
Procedure......................................................................................................... 114
Replacing the computer base.......................................116
Procedure......................................................................................................... 116
Post-requisites.................................................................................................116
Removing the logo board................................................ 117
Prerequisites.....................................................................................................117
Procedure......................................................................................................... 118
Replacing the logo board............................................... 120
Procedure........................................................................................................ 120
Post-requisites................................................................................................120
9
Removing the camera.......................................................121
Prerequisites.................................................................................................... 121
Procedure......................................................................................................... 121
Replacing the camera...................................................... 123
Procedure........................................................................................................ 123
Post-requisites................................................................................................ 123
Removing the display-panel AlienFX LEDs............124
Prerequisites................................................................................................... 124
Procedure........................................................................................................ 125
Replacing the display-panel AlienFX LEDs.............127
Procedure.........................................................................................................127
Post-requisites.................................................................................................127
Removing the Alienware AlienHead LED board.. 128
Prerequisites................................................................................................... 128
Procedure........................................................................................................ 128
Replacing the Alienware AlienHead LED board....131
Procedure......................................................................................................... 131
Post-requisites.................................................................................................131
Removing the display back-cover............................. 132
Prerequisites................................................................................................... 132
Procedure........................................................................................................ 132
Replacing the display back-cover..............................135
Procedure........................................................................................................ 135
Post-requisites................................................................................................ 135
10
BIOS setup program..........................................................136
Overview..........................................................................................................136
Entering BIOS setup program ........................................................................ 136
BIOS setup program options...........................................................................136
Boot sequence.................................................................................................142
Boot options.............................................................................................. 142
Changing boot sequence for the current boot......................................... 143
Changing boot sequence for future boots................................................143
Flashing the BIOS............................................................... 144
Getting help and contacting Alienware.................. 145
Self-help resources..........................................................................................145
Contacting Alienware......................................................................................145
11
Before working inside your
computer
NOTE: The images in this document may differ from your computer
depending on the configuration you ordered.
Before you begin
1 Save and close all open files and exit all open applications.
2 Shut down your computer.
– Windows 10: Click or tap Start → Power → Shut down.
– Windows 8.1: On the Start screen, click or tap the power icon →
Shut down.
– Windows 7: Click or tap Start → Shut down.
NOTE: If you are using a different operating system, see the
documentation of your operating system for shut-down instructions.
3 Disconnect your computer and all attached devices from their electrical
outlets.
4 Disconnect all cables such as telephone cables, network cables and so on,
from your computer.
5 Disconnect all attached devices and peripherals, such as keyboard, mouse,
monitor, and so on, from your computer.
6 Remove any media card and optical disc from your computer, if applicable.
Safety instructions
Use the following safety guidelines to protect your computer from potential
damage and ensure your personal safety.
WARNING: Before working inside your computer, read the
safety information that shipped with your computer. For
more safety best practices, see the Regulatory Compliance
home page at www.dell.com/regulatory_compliance.
12
WARNING: Disconnect all power sources before opening the
computer cover or panels. After you finish working inside
the computer, replace all covers, panels, and screws before
connecting to the power source.
CAUTION: To avoid damaging the computer, ensure that the
work surface is flat and clean.
CAUTION: To avoid damaging the components and cards,
handle them by their edges and avoid touching pins and
contacts.
CAUTION: You should only perform troubleshooting and
repairs as authorized or directed by the Dell technical
assistance team. Damage due to servicing that is not
authorized by Dell is not covered by your warranty. See the
safety instructions that shipped with the product or at
www.dell.com/regulatory_compliance.
CAUTION: Before touching anything inside your computer,
ground yourself by touching an unpainted metal surface,
such as the metal at the back of the computer. While you
work, periodically touch an unpainted metal surface to
dissipate static electricity, which could harm internal
components.
CAUTION: When you disconnect a cable, pull on its connector
or on its pull tab, not on the cable itself. Some cables have
connectors with locking tabs or thumb-screws that you
must disengage before disconnecting the cable. When
disconnecting cables, keep them evenly aligned to avoid
bending any connector pins. When connecting cables,
ensure that the ports and connectors are correctly oriented
and aligned.
CAUTION: Press and eject any installed card from the media-
card reader.
Recommended tools
The procedures in this document may require the following tools:
• Phillips screwdriver
• Plastic scribe
13
After working inside your
computer
CAUTION: Leaving stray or loose screws inside your
computer may severely damage your computer.
1 Replace all screws and ensure that no stray screws remain inside your
computer.
2 Connect any external devices, peripherals, and cables you removed before
working on your computer.
3 Replace any media cards, discs, and any other parts that you removed
before working on your computer.
4 Connect your computer and all attached devices to their electrical outlets.
5 Turn on your computer.
14
Removing the base panel
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Close the display and turn the computer over.
2 Loosen the captive screws that secure the base panel to the computer
base.
3 Gently release the tabs that secure the base panel to the computer base.
4 Slide and remove the base panel from the computer base.
1 computer base 2 captive screws (2)
3 base panel
15
5 Disconnect the battery cable from the system board.
1 battery cable
6 Turn the computer over.
7 Press and hold the power button for 5 seconds to ground the system
board.
16
Replacing the base panel
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Connect the battery cable to the system board.
2 Slide the tabs on the base panel into the slots on the computer base and
snap the base panel into place.
3 Tighten the captive screws that secure the base panel to the computer
base.
17
Removing the memory
modules
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
Remove the base panel.
Procedure
1 Using your fingertips, carefully spread apart the securing clips on each end
of the memory-module slot until the memory module pops up.
18
2 Slide and remove the memory module from the memory-module slot.
1 securing clips (2) 2 memory modules (2)
3 memory-module slot
19
Replacing the memory
modules
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Align the notch on the memory module with the tab on the memory-
module slot.
20
2 Slide the memory module firmly into the slot at an angle and press the
memory module down until it clicks into place.
NOTE: If you do not hear the click, remove the memory module and
reinstall it.
1 securing clips (2) 2 memory module
3 memory-module slot 4 notch
5 tab
Post-requisites
Replace the base panel.
21
Removing the solid-state
drives
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
CAUTION: Solid-state drives are fragile. Exercise care when
handling the hard drive.
CAUTION: To avoid data loss, do not remove the solid-state
drive while the computer is in sleep or on state.
Prerequisites
Remove the base panel.
Procedure
NOTE: Your computer can accommodate either one 2.5-inch hard drive or
four solid-state drives.
1 Remove the screw that secures the solid-state drive to the computer base.
22
2 Slide and remove the solid-state drive from the solid-state drive slot.
1 solid-state drive slot 2 solid-state drive
3 screw
23
Replacing the solid-state
drives
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
CAUTION: Solid-state drives are fragile. Exercise care when
handling the hard drive.
Procedure
1 Slide the solid-state drive into the solid-state drive slot.
2 Replace the screw that secures the solid-state drive to the computer base.
Post-requisites
Replace the base panel.
24
Removing the hard drive
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
CAUTION: Hard drives are fragile. Exercise care when
handling the hard drive.
CAUTION: To avoid data loss, do not remove the hard drive
while the computer is in sleep or on state.
Prerequisites
Remove the base panel.
Procedure
NOTE: Your computer can accommodate either one 2.5-inch hard drive or
four solid-state drives.
1 Using the pull tab, disconnect the hard-drive cable from the system board.
2 Note the hard-drive cable routing and remove the cable from the routing
guides on the computer base.
3 Remove the screws that secure the hard-drive assembly to the computer
base.
25
4 Lift the hard-drive assembly off the computer base.
1 pull tab 2 hard-drive cable
3 screws (4) 4 hard-drive assembly
5 Remove the screws that secure the hard-drive bracket to the hard drive.
6 Lift the hard-drive bracket off the hard-drive assembly.
1 hard drive 2 hard-drive bracket
3 screws (4)
26
7 Disconnect the interposer from the hard drive.
1 interposer 2 hard drive
27
Replacing the hard drive
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
CAUTION: Hard drives are fragile. Exercise care when
handling the hard drive.
Procedure
1 Connect the interposer to the hard drive.
2 Align the screw holes on the hard-drive bracket with the screw holes on
the hard-drive assembly.
3 Replace the screws that secure the hard-drive bracket to the hard-drive
assembly.
4 Align the screw holes on the hard-drive assembly with the screw holes on
the computer base.
5 Replace the screws that secure the hard-drive assembly to the computer
base.
6 Route the hard-drive cable through the routing guides on the computer
base.
7 Connect the hard-drive cable to the system board.
Post-requisites
Replace the base panel.
28
Removing the palm rest
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
Remove the base panel.
29
Procedure
1 Lift the latches and disconnect the keyboard cable, keyboard-backlight
cable, macro-keys cable and macro-keys backlight cable from the system
board.
1 keyboard-backlight cable 2 keyboard cable
3 macro-keys cable 4 latches (4)
5 macro-keys backlight cable
30
2 Remove the screws that secure the palm-rest assembly to the computer
base.
1 computer base 2 screws (16)
31
3 Lift the computer base slightly and push the palm-rest assembly through
the slot on the computer base to release the tabs on the palm-rest
assembly.
1 slot 2 palm-rest assembly
4 Turn the computer over and open the display as far as possible.
5 Using a plastic scribe, pry up along the edges of the palm-rest assembly.
32
6 Gently lift the palm-rest assembly and turn it over.
1 plastic scribe 2 palm-rest assembly
7 Peel the tape that secures the power-button board cable to the system
board.
8 Disconnect the power-button board cable from the system board.
33
Replacing the palm rest
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Replace the touch pad.
2 Replace the keyboard.
3 Replace the status-light board.
4 Replace the power-button board.
5 Connect the power-button board cable to the system board.
6 Adhere the tape that secures the power-button board cable to the system
board.
7 Slide the keyboard cable, keyboard-backlight cable, macro-keys cable, and
macro-keys backlight cable through the slot on the computer base.
8 Align the palm-rest assembly on the computer base and snap it into place.
9 Close the display and turn the computer over.
10 Replace the screws that secure the palm-rest assembly to the computer
base.
11 Slide the keyboard cable, keyboard-backlight cable, macro-keys cable and
macro-keys backlight cable into their respective connectors and press
down the latches to secure the cables to the system board.
Post-requisites
Replace the base panel.
36
Removing the power-button
board
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
Procedure
1 Lift the latches and disconnect the touch-pad cable and the status-light
cable from the power-button board.
2 Disconnect the power-button board cable from the power-button board.
3 Remove the screws that secure the power-button board to the palm-rest
assembly.
37
4 Lift the power-button board off the palm-rest assembly.
1 power-button board cable 2 latches (2)
3 touch-pad cable 4 status-light cable
5 screws (2) 6 power-button board
38
Replacing the power-button
board
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Align the screw holes on the power-button board with the screw holes on
the palm-rest assembly.
2 Replace the screws that secure the power-button board to the palm-rest
assembly.
3 Connect the power-button board cable to the power-button board.
4 Slide the touch-pad cable and the status-light cable into their respective
connectors on the power-button board and press down the latches to
secure the cables.
Post-requisites
1 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
2 Replace the base panel.
39
Removing the status-light
board
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
Procedure
1 Lift the latch and disconnect the status-light board cable from the status-
light board.
2 Remove the screws that secure the status-light board to the palm-rest
assembly.
40
3 Lift the status-light board off the palm-rest assembly.
1 screws (2) 2 latch
3 status-light board cable 4 status-light board
41
Replacing the status-light
board
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Align the screw holes on the status-light board with the screw holes on the
palm-rest assembly.
2 Replace the screws that secure the status-light board to the palm-rest
assembly.
3 Slide the status-light board cable into the connector on the status-light
board and press down the latch to secure the cable.
Post-requisites
1 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
2 Replace the base panel.
42
Removing the keyboard
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
Procedure
1 Lift the latches and disconnect the touch-pad cable and the status-light
cable from the power-button board.
43
2 Note the touch-pad cable and status-light cable routing and peel off the
cables from the keyboard bracket.
1 latches (2) 2 touch-pad cable
3 status-light cable
3 Remove the screws that secure the keyboard bracket to the palm-rest
assembly.
4 Slide the keyboard cable, keyboard-backlight cable, macro-keys cable and
macro-keys backlight cable through the slot on the keyboard bracket.
44
5 Lift the keyboard bracket off the palm-rest assembly.
1 screws (14) 2 keyboard bracket
3 palm-rest assembly
6 Remove the screws that secure the keyboard to the palm-rest assembly.
7 Release the tabs that secure the keyboard to the palm-rest assembly.
45
8 Slide and lift the keyboard along with the cables off the palm-rest
assembly.
1 tabs (5) 2 keyboard
3 screws (2)
46
Replacing the keyboard
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Slide the keyboard under the tabs on the palm-rest assembly.
2 Align the screw holes on the keyboard with the screw holes on the palm-
rest assembly.
3 Replace the screws that secure the keyboard to the palm-rest assembly.
4 Route the keyboard cable, keyboard-backlight cable, macro-keys cable and
macro-keys backlight cable through the slots on the keyboard bracket.
5 Align the screw holes on the keyboard bracket with the screw holes on the
palm-rest assembly.
6 Replace the screws that secure the keyboard bracket to the palm-rest
assembly.
7 Adhere the touch-pad cable and status-light cable to the keyboard bracket.
8 Slide the touch-pad cable and the status-light cable into their respective
connectors on the power-button board and press down the latches to
secure the cables.
Post-requisites
1 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
2 Replace the base panel.
47
Removing the touch pad
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
48
Procedure
1 Lift the latches and disconnect the touch-pad cable and touch-pad button
cable from the touch pad.
1 touch-pad cable 2 latches (2)
3 touch-pad button cable
2 Remove the screws that secure the touch-pad button bracket to the palm-
rest assembly.
49
3 Lift the touch-pad button bracket off the palm-rest assembly.
1 touch-pad button bracket 2 screws (5)
4 Lift the touch pad off the palm-rest assembly.
1 touch pad
50
Replacing the touch pad
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Using the alignment posts on the palm-rest assembly, place the touch pad
on the palm-rest assembly.
2 Slide the touch-pad button cable into the touch-pad button connector and
press down the latch to secure the cable.
3 Align the screw holes on the touch-pad button bracket with the screw
holes on the palm-rest assembly.
4 Replace the screws that secure the touch-pad button bracket to the palm-
rest assembly.
5 Slide the touch-pad cable into the touch-pad connector and press down
the latch to secure the cable.
Post-requisites
1 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
2 Replace the base panel.
51
Removing the display
assembly
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
Procedure
1 Close the display and turn the computer over.
2 Remove the screws that secure the display assembly to the computer
base.
3 Remove the screw that secures the wireless-card bracket and the wireless
card to the system board.
4 Lift the wireless-card bracket off the wireless card.
52
5 Disconnect the antenna cables from the wireless card.
1 wireless-card bracket 2 screws (3)
3 antenna cables
6 Turn the computer over and open the display.
7 Peel off the adhesive tape that secures the antenna cables to the system
board.
8 Carefully remove the antenna cables up from the computer base and
remove it from the routing guides on the display hinges.
9 Lift the latch and disconnect the display cable from the system board.
10 Remove the display cable from the routing guide on the display hinge.
53
11 Disconnect the logo-board cable from the system board and remove it
from the routing guide on the display hinge.
1 display cable 2 latch
3 connector 4 logo-board cable
5 antenna cables 6 tape
12 Remove the screws that secure the display assembly to the computer
base.
54
13 Lift the display assembly off the computer base.
1 display assembly 2 screws (4)
3 computer base 4 display hinges (2)
55
Replacing the display
assembly
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Align the screw holes on the display hinges with the screw holes on the
computer base.
2 Replace the screws that secure the display assembly to the computer
base.
3 Route the logo-board cable through the routing guide on the display hinge
and connect the logo-board cable to the system board.
4 Route the display cable through the routing guide on the display hinge.
5 Slide the display cable into the connector on the system board and press
down on the latch to secure the cable.
6 Route the antenna cables through the routing guide on the display hinge
and on the computer base.
7 Connect the antenna cables to the wireless card.
The following table provides the antenna-cable color scheme for the
wireless card supported by your computer.
Connectors on the wireless card Antenna-cable color
Main (white triangle) White
Auxiliary (black triangle) Black
8 Align the screw hole on the wireless-card bracket with the screw hole on
the wireless card.
9 Replace the screw that secures the wireless-card bracket with the wireless
card.
10 Close the display and turn the computer over.
56
Removing the battery
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
Procedure
1 Disconnect the speaker cable and front AlienFX LED cable from the system
board.
2 Remove the speaker cable from the routing guides on the battery.
58
3 Note the front AlienFX LED cable routing and peel off the cable from the
battery.
1 system board 2 speaker cable
3 front AlienFX LED cable
4 Remove the battery cable from the slot on the computer base.
5 Remove the screws that secure the battery to the computer base.
59
6 Lift the battery off the computer base.
1 battery cable 2 battery
3 screws (6)
60
Replacing the battery
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Align the screw holes on the battery with the screw holes on the computer
base.
2 Replace the screws that secure the battery to the computer base.
3 Slide the battery cable through the slot on the computer base.
4 Adhere the front AlienFX LED cable to the battery.
5 Route the speaker cable through the routing guides on the battery.
6 Connect the speaker cable and front AlienFX LED cable to the system
board.
Post-requisites
1 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
2 Replace the base panel.
61
Removing the I/O board
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
Procedure
1 Disconnect the subwoofer cable from the I/O board.
2 Lift the latch and disconnect the I/O-board cable from the I/O board.
3 Remove the screws that secure the I/O board to the computer base.
4 Gently tilt and lift to release the I/O ports from the computer base.
62
5 Lift the I/O board off the computer base.
1 subwoofer cable 2 latch
3 I/O-board cable 4 screws (2)
5 I/O board
63
Replacing the I/O board
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Align the ports on the I/O board with the slots on the computer base.
2 Align the screw holes on the I/O board with the screw holes on the
computer base.
3 Replace the screws that secure the I/O board to the computer base.
4 Connect the I/O-board cable to the I/O board.
5 Connect the subwoofer cable to the I/O board.
Post-requisites
1 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
2 Replace the base panel.
64
Removing the speakers
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
Procedure
1 Disconnect the front AlienFX LED cable from the system board.
65
2 Note the front AlienFX LED cable routing and peel off the cable from the
battery.
1 connector 2 front AlienFX LED cable
3 Disconnect the speaker cable from the system board.
4 Remove the speaker cable from the routing guides on the battery and
computer base.
66
5 Lift the speakers along with its cable off the computer base.
1 speaker cable 2 system board
3 alignment posts (4) 4 computer base
5 speakers (2) 6 routing guides
67
Replacing the speakers
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Using the alignment posts, place the speakers on the computer base.
2 Route the speaker cable through the routing guides on the computer base
and battery.
3 Route the front AlienFX LED cable through the routing guides on the
battery.
4 Connect the speaker cable and front AlienFX LED cable to the system
board.
Post-requisites
1 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
2 Replace the base panel.
68
Removing the front AlienFX
LED boards
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
Procedure
1 Disconnect the front AlienFX LED board cables from the front AlienFX LED
boards.
2 Remove the screws that secure the front AlienFX LED boards to the
computer base.
69
3 Lift the front AlienFX LED boards off the computer base.
1 front AlienFX LED boards (2) 2 front AlienFX LED board
cables (2)
3 screws (2)
70
Replacing the front AlienFX
LED board
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Using the alignment posts on the computer base, place the front AlienFX
LED boards on the computer base.
2 Align the screw holes on the front AlienFX LED boards with the screw holes
on the computer base.
3 Replace the screws that secure the front AlienFX LED boards to the
computer base.
4 Connect the front AlienFX LED board cables to the front AlienFX LED
boards.
Post-requisites
1 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
2 Replace the base panel.
71
Removing the processor fan
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
Procedure
1 Close the display and turn the computer over.
2 Disconnect the processor-fan cable from the system board.
1 processor-fan cable
72
3 Turn the computer over and open the display.
4 Remove the screws that secure the processor fan to the computer base.
5 Peel off the Mylar from the processor heat-sink and processor fan.
6 Slide and lift the processor fan off the computer base.
1 mylar 2 processor fan
3 screws (2)
73
Replacing the processor fan
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Using the alignment posts on the computer base, slide and place the
processor fan on the computer base.
2 Align the screw holes on the processor fan with the screw holes on the
computer base.
3 Adhere the Mylar on the processor fan and processor heat-sink.
4 Replace the screws that secure the processor fan to the computer base.
5 Close the display and turn the computer over.
6 Connect the processor-fan cable to the system board.
Post-requisites
1 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
2 Replace the base panel.
74
Removing the system board
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
NOTE: Your computer’s Service Tag is stored in the system board. You
must enter the Service Tag in the BIOS setup program after you replace
the system board.
NOTE: Replacing the system board removes any changes you have made
to the BIOS using the BIOS setup program. You must make the desired
changes again after you replace the system board.
NOTE: Before disconnecting the cables from the system board, note the
location of the connectors so that you can reconnect the cables correctly
after you replace the system board.
Prerequisites
1 Remove the base panel.
2 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
3 Remove the display assembly.
Procedure
1 Turn the computer over.
75
2 Disconnect the processor-fan cable, video-card fan cable, hard-drive cable
and power-adapter port cable from the system board.
1 processor-fan cable 2 power-adapter port cable
3 video-card fan cable 4 system board
5 hard-drive cable
3 Turn the computer over.
4 Disconnect the speaker and front AlienFX LED cables from the system
board.
76
5 Lift the latch and disconnect the I/O-board cable from the system board.
1 I/O-board cable 2 latch
3 system board 4 speaker cable
5 front AlienFX LED cable
6 Remove the screws that secure the system board to the computer base.
77
Replacing the system board
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
NOTE: Your computer’s Service Tag is stored in the system board. You
must enter the Service Tag in the BIOS setup program after you replace
the system board.
NOTE: Replacing the system board removes any changes you have made
to the BIOS using the BIOS setup program. You must make the desired
changes again after you replace the system board.
Procedure
1 Replace the coin-cell battery.
2 Replace the heat sink.
3 Replace the wireless card.
4 Insert the ports on the system board into the slots on the computer base
and gently place the system board on the computer base.
5 Align the screw holes on the system board with the screw holes on the
computer base.
6 Replace the screws that secure the system board to the computer base.
7 Slide the I/O-board cable into the connector on the I/O board and press
down the latch to secure the cable.
8 Connect the speaker and front AlienFX LED cables to the system board.
9 Turn the computer over.
10 Connect the processor-fan cable, video-card fan cable, hard-drive cable,
and power-adapter port cable to the system board.
Post-requisites
1 Replace the display assembly.
2 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
79
Removing the wireless card
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
3 Remove the display assembly.
4 Follow the procedure from step 1 to step 7 in “Removing the system board”.
Procedure
1 Peel the wireless card off the system board.
81
2 Lift and slide the wireless card from the wireless-card slot.
1 wireless card 2 wireless-card slot
82
Replacing the wireless card
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
CAUTION: To avoid damaging the wireless card, do not place
any cables under it.
1 Align the notch on the wireless card with the tab on the wireless-card slot.
83
2 Slide the wireless card at an angle into the wireless-card slot and press
down to adhere the wireless card to the system board.
1 wireless card 2 wireless-card slot
Post-requisites
1 Follow the procedure from step 4 to step 10 in “Replacing the system
board”.
2 Replace the display assembly.
3 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
4 Replace the base panel.
84
Removing the heat sink
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
WARNING: The heat sink may become hot during normal
operation. Allow sufficient time for the heat sink to cool
before you touch it.
CAUTION: For maximum cooling of the processor, do not
touch the heat transfer areas on the heat sink. The oils in
your skin can reduce the heat transfer capability of the
thermal grease.
Prerequisites
1 Remove the base panel.
2 Remove the wireless card.
3 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
4 Remove the display assembly.
5 Follow the procedure from step 1 to step 7 in “Removing the system board”.
Procedure
1 In sequential order (as indicated on the heat sink), loosen the captive
screws that secure the heat sink to the system board.
85
2 Lift the heat sink off the system board.
1 system board 2 captive screws (8)
3 heat sink
86
Replacing the heat sink
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
CAUTION: Incorrect alignment of the heat sink can damage
the system board and processor.
NOTE: The original thermal grease can be reused if the original system
board and heat sink are reinstalled together. If either the system board or
the heat sink is replaced, use the thermal pad provided in the kit to
ensure that thermal conductivity is achieved.
Procedure
1 Align the screw holes on the heat sink with the screw holes on the system
board.
2 In sequential order (as indicated on the heat sink), tighten the captive
screws that secure the heat sink to the system board.
3 Turn the system board over.
Post-requisites
1 Follow the procedure from step 4 to step 10 in “Replacing the system
board”.
2 Replace the display assembly.
3 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
4 Replace the wireless card.
5 Replace the base panel.
87
Removing the coin-cell
battery
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
CAUTION: Removing the coin-cell battery resets the BIOS
setup program’s settings to default. It is recommended that
you note the BIOS setup program’s settings before
removing the coin-cell battery.
Prerequisites
1 Remove the base panel.
2 Remove the wireless card.
3 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
4 Remove the display assembly.
5 Follow the procedure from step 1 to step 7 in “Removing the system board”.
Procedure
1 Disconnect the coin-cell battery cable from the system board.
88
2 Peel the coin-cell battery off the system board.
1 coin-cell battery 2 coin-cell battery cable
89
Replacing the coin-cell
battery
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Adhere the coin-cell battery to the system board.
2 Connect the coin-cell battery cable to the connector on the system board.
Post-requisites
1 Follow the procedure from step 4 to step 10 in “Replacing the system
board”.
2 Replace the display assembly.
3 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
4 Replace the wireless card.
5 Replace the base panel.
90
Removing the video-card fan
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Remove the wireless card.
3 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
4 Remove the display assembly.
5 Follow the procedure from step 1 to step 7 in “Removing the system board”.
Procedure
1 Remove the screws that secure the video-card fan to the computer base.
91
2 Lift the video-card fan off the computer base.
1 screws (2) 2 video-card fan
92
Replacing the video-card fan
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Align the screw holes on the video-card fan with the screw holes on the
computer base.
2 Replace the screws that secure the video-card fan to the computer base.
Post-requisites
1 Follow the procedure from step 4 to step 10 in “Replacing the system
board”.
2 Replace the display assembly.
3 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
4 Replace the wireless card.
5 Replace the base panel.
93
Removing the power-
adapter port
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Remove the wireless card.
3 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
4 Remove the display assembly.
5 Follow the procedure from step 1 to step 7 in “Removing the system board”.
Procedure
1 Remove the screws that secure the power-adapter port bracket to the
power-adapter port.
2 Lift the power-adapter port bracket off the power-adapter port.
3 Note the power-adapter port cable routing and remove the cable from the
routing guides on the computer base.
94
4 Lift the power-adapter port along with its cable off the computer base.
1 screws (2) 2 power-adapter port
bracket
3 power-adapter port
95
Replacing the power-adapter
port
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Slide the power-adapter port into the slot on the computer base.
2 Align the screw holes on the power-adapter port bracket with the screw
holes on the power-adapter port.
3 Replace the screws that secure the power-adapter port bracket to the
power-adapter port.
4 Route the power-adapter port cable through the routing guides on the
computer base.
Post-requisites
1 Follow the procedure from step 4 to step 10 in “Replacing the system
board”.
2 Replace the display assembly.
3 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
4 Replace the wireless card.
5 Replace the base panel.
96
Removing the subwoofer
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Remove the wireless card.
3 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
4 Remove the I/O board.
5 Remove the display assembly.
6 Follow the procedure from step 1 to step 7 in “Removing the system board”.
Procedure
1 Remove the screws that secure the subwoofer to the computer base.
97
2 Lift the subwoofer off the computer base.
1 screws (2) 2 subwoofer
98
Replacing the subwoofer
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Align the screw holes on the subwoofer with the screw holes on the
computer base.
2 Replace the screws that secure the subwoofer to the computer base.
Post-requisites
1 Follow the procedure from step 4 to step 10 in “Replacing the system
board”.
2 Replace the display assembly.
3 Replace the I/O board.
4 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
5 Replace the wireless card.
6 Replace the base panel.
99
Removing the display bezel
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
NOTE: This chapter is applicable only if you have purchased a laptop with
non-touchscreen display.
1 Remove the base panel.
2 Remove the wireless card.
3 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
4 Remove the display assembly.
Procedure
1 Using your fingertips, carefully pry up the inside edges of the display bezel.
100
2 Carefully lift the display bezel and turn it over.
1 display bezel
3 Lift the latches and disconnect the display-board cables from the logo
board.
101
4 Lift the display-bezel assembly away from the display assembly.
1 display bezel 2 logo board
3 latches (3) 4 display-board cables (3)
5 Peel off the tape that secures the logo-board cable to the logo board and
disconnect the logo-board cable.
102
6 Peel off the logo board from the display bezel.
1 display bezel 2 logo board
3 plastic scribe 4 logo-board cable
5 tape
103
7 After performing the above steps, we are left with the display bezel.
1 display bezel
104
Replacing the display bezel
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
NOTE: This chapter is applicable only if you have purchased a laptop with
non-touchscreen display.
1 Adhere the logo board on the display bezel.
2 Connect the logo-board cable to the logo board and adhere the adhesive
tape.
3 Slide the display-board cables to their respective connectors on the logo
board and press down the latches to secure the cables.
4 Turn the display bezel over.
5 Align the display bezel with the display back-cover and gently snap the
display bezel into place.
Post-requisites
1 Replace the display assembly.
2 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
3 Replace the wireless card.
4 Replace the base panel.
105
Removing the display panel
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
NOTE: This chapter is applicable only if you have purchased a laptop with
non-touchscreen display.
1 Remove the base panel.
2 Remove the wireless card.
3 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
4 Remove the display assembly.
5 Remove the display bezel.
Procedure
1 Remove the screws that secure the display panel to the display back-cover.
106
2 Gently lift the display panel and turn it over.
1 screws (4) 2 display panel
3 display back-cover
3 Lift the latch and disconnect the display cable from the display panel.
107
4 Lift the display panel off the display assembly.
1 display panel 2 latch
3 display cable
108
Replacing the display panel
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
NOTE: This chapter is applicable only if you have purchased a laptop with
non-touchscreen display.
1 Connect the display cable to the display panel and press down on the latch
to secure the cable.
2 Turn the display panel over.
3 Align the screw holes on the display panel with the screw holes on the
display back-cover.
4 Replace the screws that secure the display panel to the display back-cover.
Post-requisites
1 Replace the display bezel.
2 Replace the display assembly.
3 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
4 Replace the wireless card.
5 Replace the base panel.
109
Removing the display hinges
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
NOTE: This chapter is applicable only if you have purchased a laptop with
non-touchscreen display.
1 Remove the base panel.
2 Remove the wireless card.
3 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
4 Remove the display assembly.
5 Remove the display bezel.
Procedure
1 Remove the screws that secure the hinge caps to the display hinges.
110
2 Lift the hinge caps off the display hinges.
1 hinge caps (2) 2 screws (2)
3 Remove the screws that secure the display hinges to the display back-
cover.
111
4 Lift the display hinges off the display back-cover.
1 display hinges (2) 2 screws (6)
112
Replacing the display hinges
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
NOTE: This chapter is applicable only if you have purchased a laptop with
non-touchscreen display.
1 Align the screw holes on the display hinges with the screw holes on the
display back-cover.
2 Replace the screws that secure the display hinges to the display back-
cover.
3 Align the screw holes on the hinge caps with the screw holes on the
display hinges.
4 Replace the screws that secure the hinge caps to the display hinges.
Post-requisites
1 Replace the display bezel.
2 Replace the display assembly.
3 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
4 Replace the wireless card.
5 Replace the base panel.
113
Removing the computer
base
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Remove the wireless card.
3 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
4 Remove the display assembly.
5 Remove the power-adapter port.
6 Remove the battery.
7 Remove the speakers.
8 Remove the I/O board.
9 Remove the subwoofer.
Procedure
After performing the prerequisites, we are left with the computer base.
114
1 computer base
115
Replacing the computer
base
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
Place the computer base on a flat surface.
Post-requisites
1 Replace the subwoofer.
2 Replace the I/O board.
3 Replace the speakers.
4 Replace the battery.
5 Replace the power-adapter port.
6 Replace the display assembly.
7 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
8 Replace the wireless card.
9 Replace the base panel.
116
Removing the logo board
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Remove the wireless card.
3 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
4 Remove the display assembly.
5 Follow the procedure from step 1 to step 2 in removing the display bezel.
117
Procedure
1 Lift the latches and disconnect the display-board cables from the logo
board.
1 display bezel 2 logo board
3 latches (3) 4 display-board cables (3)
2 Peel off the tape that secures the logo-board cable to the logo board and
disconnect the logo-board cable.
118
3 Peel off the logo board from the display bezel.
1 display bezel 2 logo board
3 plastic scribe 4 logo-board cable
5 tape
119
Replacing the logo board
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Adhere the logo board on the display bezel.
2 Connect the logo-board cable to the logo board and adhere the adhesive
tape.
3 Slide the display-board cables to their respective connectors on the logo
board and press down the latches to secure the cables.
Post-requisites
1 Replace the display bezel.
2 Replace the display assembly.
3 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
4 Replace the wireless card.
5 Replace the base panel.
120
Removing the camera
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
NOTE: This chapter is applicable only if you have purchased a laptop with
non-touchscreen display.
1 Remove the base panel.
2 Remove the wireless card.
3 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
4 Remove the display assembly.
5 Remove the display bezel.
Procedure
1 Place the display back-cover assembly on a flat surface.
2 Using a plastic scribe, pry the camera module off the display back-cover.
121
3 Disconnect the camera cable from the camera module.
1 camera module 2 tape
3 plastic scribe 4 camera cable
5 connector
122
Replacing the camera
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
NOTE: This chapter is applicable only if you have purchased a laptop with
non-touchscreen display.
1 Using the alignment posts, adhere the camera module to the display back-
cover and snap it into place.
2 Connect the camera cable to the camera module.
Post-requisites
1 Replace the display bezel.
2 Replace the display assembly.
3 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
4 Replace the wireless card.
5 Replace the base panel.
123
Removing the display-panel
AlienFX LEDs
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Remove the wireless card.
3 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
4 Remove the display assembly.
5 Remove the display bezel.
6 Remove the display panel.
124
Procedure
1 Peel off the mylar that secures the display-board cables and the display-
panel AlienFX LEDs to the display back-cover.
1 mylar
125
2 Lift the display-board cables and the display-panel AlienFX LEDs off the
display back-cover.
1 display back-cover 2 display-board cables (2)
3 display-panel AlienFX LEDs
(2)
126
Replacing the display-panel
AlienFX LEDs
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Adhere the display-board cables and the display-panel AlienFX LEDs to the
display back-cover.
2 Adhere the mylar that secures the display-board cables and the display-
panel AlienFX LEDs to the display back-cover.
Post-requisites
1 Replace the display panel.
2 Replace the display bezel.
3 Replace the display assembly.
4 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
5 Replace the wireless card.
6 Replace the base panel.
127
Removing the Alienware
AlienHead LED board
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1 Remove the base panel.
2 Remove the wireless card.
3 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
4 Remove the display assembly.
5 Remove the display bezel.
6 Remove the display panel.
Procedure
1 Peel off the mylar that secures the display-board cables and the display-
panel AlienFX LEDs to the display back-cover.
2 Disconnect the camera cable from the camera module.
128
3 Peel off the mylar to access the Alienware AlienHead LED board.
1 mylar 2 display back-cover
3 camera cable 4 connector
5 camera module
129
4 Lift the display-board cable and Alienware AlienHead LED board off the
display back-cover.
1 display-board cable 2 Alienware AlienHead LED
board
3 display back-cover
130
Replacing the Alienware
AlienHead LED board
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1 Connect the camera cable to the camera module.
2 Adhere the Alienware AlienHead LED board and display-board cable to the
display back-cover.
3 Adhere the mylar to secure the Alienware AlienHead LED board and
display-board cable and to the display back-cover.
4 Adhere the mylar to secure the display-board cables and the display-panel
AlienFX LEDs to the display back-cover.
Post-requisites
1 Replace the display panel.
2 Replace the display bezel.
3 Replace the display assembly.
4 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
5 Replace the wireless card.
6 Replace the base panel.
131
Removing the display back-
cover
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
NOTE: This chapter is applicable only if you have purchased a laptop with
non-touchscreen display.
1 Remove the base panel.
2 Remove the wireless card.
3 Follow the procedure from step 1 to step 9 in “Removing the palm rest”.
4 Remove the display assembly.
5 Remove the display bezel.
6 Remove the display panel.
7 Remove the camera.
8 Remove the display-panel AlienFX LEDs.
9 Remove the Alienware AlienHead LED board.
Procedure
1 Disconnect the camera cable from the camera module.
2 Remove the display-board cable from the routing guides on the display
back-cover.
132
3 Peel the display-board and camera cable off the display back-cover.
1 camera cable 2 connector
3 camera module
4 Remove the AlienFX Display light.
5 Remove the AlienFX AlienHead board.
133
6 We are left with the display back-cover.
1 display back-cover
134
Replacing the display back-
cover
WARNING: Before working inside your computer, read the
safety information that shipped with your computer and
follow the steps in Before working inside your computer.
After working inside your computer, follow the instructions
in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
NOTE: This chapter is applicable only if you have purchased a laptop with
non-touchscreen display.
1 Replace the AlienFX AlienHead board.
2 Replace the AlienFX Display light.
3 Adhere the display-board and camera cable to the display back-cover.
4 Route the display-board cable through the routing guides on the display
back-cover.
5 Connect the camera cable to the camera module.
Post-requisites
1 Replace the Alienware AlienHead LED board.
2 Replace the display-panel AlienFX LEDs.
3 Replace the camera.
4 Replace the display panel.
5 Replace the display bezel.
6 Replace the display assembly.
7 Follow the procedure from step 5 to step 11 in “Replacing the palm rest”.
8 Replace the wireless card.
9 Replace the base panel.
135
BIOS setup program
Overview
CAUTION: Unless you are an expert computer user, do not
change the settings in the BIOS setup program. Certain
changes can make your computer work incorrectly.
NOTE: Before you change BIOS setup program, it is recommended that
you write down the BIOS setup program screen information for future
reference.
Use BIOS setup program to:
• Get information about the hardware installed in your computer, such as the
amount of RAM, the size of the hard drive, and so on.
• Change the system configuration information.
• Set or change a user-selectable option, such as the user password, type of
hard drive installed, enabling or disabling base devices, and so on.
Entering BIOS setup program
1 Turn on (or restart) your computer.
2 During POST, when the Alienware logo is displayed, watch for the F2
prompt to appear and then press F2 immediately.
NOTE: The F2 prompt indicates that the keyboard has initialized. This
prompt can appear very quickly, so you must watch for it, and then
press F2. If you press F2 before the F2 prompt, this keystroke is lost. If
you wait too long and the operating system logo appears, continue to
wait until you see the operating system’s desktop. Then, restart your
computer and try again.
BIOS setup program options
NOTE: Depending on your computer and its installed devices, the items
listed in this section may or may not appear.
136
Main
System Time Displays the current time in hh:mm:ss
format.
System Date Displays the current date in mm/dd/
yyyy format.
BIOS Version Displays the BIOS version.
Product Name Displays the model number of your
computer.
Service Tag Displays the service tag of your
computer.
Asset Tag Displays the asset tag of your
computer.
CPU Type Displays the processor type.
CPU Speed Displays the processor speed.
CPU ID Displays the processor identification
code.
L1 Cache Displays the processor L1 cache size.
L2 Cache Displays the processor L2 cache size.
L3 Cache Displays the processor L3 cache size.
Integrated Graphics Displays the integrated graphics.
Discrete Graphics 1 Displays the first discrete graphics
installed on your computer.
Fixed HDD Displays the type of hard-drive
installed.
Second HDD Displays the type of secondary hard-
drive installed.
Third HDD Displays the type of third hard-drive
installed.
Fourth HDD Displays the type of fourth hard-drive
installed.
Fifth HDD Displays the type of fifth hard-drive
installed.
AC Adapter Type Displays the type of AC adapter
connected to your computer.
137
Main
System Memory Displays the system memory.
Extended Memory Displays the extended memory.
Memory Speed Displays the memory speed.
Advanced
Intel(R) SpeedStep (TM) Allows you to disable or enable Intel (R)
SpeedStep Technology.
NOTE: If enabled, the processor
clock speed and core voltage are
adjusted dynamically based on the
processor load.
Default: Enabled
Virtualization Allows you to disable or enable the Intel
Virtualization technology. Default:
Enabled
VT for Direct I/O Allows you to disable or enable a Virtual
Machine Monitor (VMM) to use the
additional hardware capabilities
provided by Intel(R) Virtualization
Technology for Direct I/O. Default:
Enabled
Integrated NIC Allows you to disable or enable the on-
board LAN controller. Default: Enabled
USB Emulation Allows you to enable or disable the USB
emulation feature. This feature defines
how the BIOS, in the absence of a USB-
aware operating system, handles USB
devices. USB emulation is always
enabled during POST. Default: Enabled
NOTE: You cannot boot any type of
USB device (floppy, hard drive, or
memory key) when this option is
disabled.
USB PowerShare Allows you to charge USB devices when
the computer is turned off or in standby
mode. Default: Enabled
138
Advanced
USB Wake Support Allows you to enable USB devices to
wake the computer from standby or to
disable the USB wake support feature.
Default: Disabled
NOTE: If USB PowerShare is
enabled, a device connected to the
USB PowerShare connector may
not wake the computer.
SATA Operation Allows you to configure the operating
mode of the integrated SATA hard-drive
controller. Default: AHCI
Adapter Warnings Allows you to choose if the computer
should display warning messages when
you use AC adapters that are not
supported by your computer. Default:
Enabled
Function Key Behavior Allows you to set function key or
multimedia key as the default function
key behavior. Default: Function key
Express Charge Allows you to charge your computer
battery using Standard Charge or
Express Charge mode. Default: Express
Charge
Touchpad Backlight Allows you to set the touch pad
backlight to be on or in auto mode.
Battery Health Displays the battery health.
Advanced-Miscellaneous Devices
External USB Ports Allows you to disable or enable the
external USB ports. Default: Enabled
USB debug Allows you to enable or disable USB
port for Windows debugging. Default:
Disabled
139
Advanced-Performance options with Alienware Graphics
Amplifier
Overclocking Feature Allows you to enable or disable global
overclocking feature. Default: Disabled
NOTE: The following features are
available only when the
Overclocking Feature is enabled.
Non-Turbo Flex Support Allows you to enable or disable non-
turbo flex support. Default: Enabled
Flex Ratio Override Allows you to set the flex ratio
override value.
Override Turbo Settings Allows you to enable or disable the
override turbo settings. Default:
Enabled
Long Duration PWR Limit Allows you to set the turbo mode long
duration power limit.
Long Duration Time Window Allows you to set the turbo mode time
value in seconds.
Short Duration PWR Limit Allows you to enable or disable short
duration power limit. Default: Enabled
Short Duration PWR Limit Options Allows you to set the turbo mode
power limit value in watts.
Bus Clock
Current Frequency Displays the current bus clock
frequency.
New Frequency in 10KHz
increments
Allows you to set the bus clock
frequency in increments of 10 KHz.
Apply New Bus Clock Frequency Applies the new bus clock frequency
immediately, temporarily, or
permanently.
Intel Graphics Turbo Overclocking Allows you to disable or enable the
Intel Graphics Turbo Overclocking
feature.
Memory Override Support Allows you to enable or disable the
memory override option support.
Default: Disabled
140
Security
Unlock Setup Status Displays if the setup status is
unlocked. Default: Unblocked.
Admin Password Status Displays if the administrator password
is clear or set. Default: Not set
System password Status Displays if the system password is
clear or set. Default: Not set
HDD password Status Displays if the HDD password is clear
or set. Default: Not set
NOTE: The password is set for all
the installed hard drives on your
computer.
Service Tag Displays the Service Tag of the
computer when the Service Tag is
present. Displays a field to input the
Service Tag manually when the
Service Tag is absent.
NOTE: The Service Tag option is
available only when the Service
Tag is not set.
Admin Password Allows you to set the administrator
password. The administrator
password controls access to the BIOS
setup program utility.
System Password Allows you to set the system
password. The system password
controls access to the computer at
boot.
HDD password Allows you to set, change, or delete
the hard-drives password.
Password Change Allows you to permit or deny system
password or HDD password changes.
Default: Permitted
141
Exit
Save Changes and Reset Allows you to exit the BIOS setup
program and save your changes.
Discard Changes and Reset Allows you to exit the BIOS setup
program and load previous values for
all BIOS setup program options.
Restore Defaults Allows you to restore default values
for all BIOS setup program options.
Discard Changes Allows you to load previous values for
all BIOS setup program options.
Save Changes Allows you to save the changes for all
BIOS setup program options.
Boot sequence
This feature allows you to change the sequence of devices that your computer
attempts to boot from. If the computer cannot boot from the device you select,
it attempts to boot from the next bootable device. You can use this feature to
change the:
• Current Boot Sequence — change the boot sequence for the current boot,
for example, to boot from the optical drive to run Alienware Diagnostics
from the Drivers and Utilities disc or to reinstall your operating system
using an external media. The previous boot sequence is restored at the next
boot.
• Future Boot Sequence — change the boot sequence for all future boots, for
example, to boot from the primary hard drive.
Boot options
NOTE: The following boot options are available only when the Boot List
Option is set to Legacy.
Floppy (Diskette Drive) — The computer attempts to boot from the floppy
disk drive. If no operating system is on the drive, the computer generates an
error message.
Hard Drive — The computer attempts to boot from the primary hard drive. If
no operating system is on the drive, the computer generates an error message.
CD/DVD/CD-RW Drive — The computer attempts to boot from the optical
drive. If no disc is in the drive, or if the disc is not bootable, the computer
generates an error message.
142
USB Storage Device — Insert the memory device into a USB connector and
restart the computer. When F12 Boot Options appear in the lower-right
corner of the screen, press F12. The BIOS detects the device and adds the USB
flash option to the boot menu.
NOTE: To boot to a USB device, the device must be bootable. To ensure
that your device is bootable, check the device documentation.
Network — The computer attempts to boot from the network. If no operating
system is found on the network, the computer generates an error message.
Changing boot sequence for the current boot
1 If you are booting from a USB device, connect the USB device to a USB port.
2 Turn on (or restart) your computer.
3 When F2 Setup, F12 Boot Options appear in the lower-right corner of
the screen, press F12.
NOTE: If you wait too long and the operating system logo appears,
continue to wait until you see the Microsoft Windows desktop. Then,
shut down your computer and try again.
The Boot Options appears, listing all available boot devices.
4 On the Boot Options, select the device you want to boot from and press
Enter.
For example, if you are booting to a USB hard drive, highlight USB Hard
Disk and press Enter.
Changing boot sequence for future boots
1 Enter BIOS setup program.
See “Entering BIOS setup program”.
2 Use the arrow keys to highlight the Boot menu option and press Enter to
access the menu.
NOTE: Note your current boot sequence in case you want to restore
it.
3 Navigate to Set Boot Priority to configure the boot priority.
4 Use the arrow keys to highlight the boot priority and press Enter to display
the different devices.
5 Select the device and press Enter to set the boot priority.
143
Flashing the BIOS
You may need to flash (update) the BIOS when an update is available or when
you replace the system board. To flash the BIOS:
1 Turn on the computer.
2 Go to www.dell.com/support.
3 Click Product Support, enter the Service Tag of your computer and click
Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature
or manually browse for your computer model.
4 Click Drivers & downloads.
5 Select the operating system installed on your computer.
6 Scroll down the page and expand BIOS.
7 Click Download File to download the latest version of the BIOS for your
computer.
8 Save the file and, once the download is complete, navigate to the folder
where you saved the BIOS update file.
9 Double-click the BIOS update file icon and follow the instructions on the
screen.
144
Getting help and contacting
Alienware
Self-help resources
You can get information and help on Alienware products and services using
these online self-help resources:
Self-Help Information Self-Help Options
Accessing Windows Help Windows 10/Windows 8.1—In
Windows search, type Help and
Support, and press Enter.
Windows 7—Click Start → Help
and Support.
Learn about Windows Launch the:
•Dell Help & Support app
(Windows 10/Windows 8.1)
•Get started app (Windows 10)
•Help+Tips app (Windows 8.1)
Information about Alienware products
and services
www.alienware.com
Troubleshooting information, user
manuals, setup instructions, product
specifications, technical help blogs,
drivers, software updates, and so on
www.alienware.com/
gamingservices
Videos providing step-by-step
instructions to service your computer
www.youtube.com/
alienwareservices
Contacting Alienware
To contact Alienware for sales, technical support, or customer service issues,
see www.alienware.com.
NOTE: Availability varies by country and product, and some services may
not be available in your country.
145
NOTE: If you do not have an active internet connection, you can find
contact information on your purchase invoice, packing slip, bill, or Dell
product catalog.
146