Command Reference for AlliedWare Plus™ Version 5.4.6-2.x

Allied Telesis AT-FS980M/52-10 User Manual

Displayed below is the user manual for AT-FS980M/52-10 by Allied Telesis which is a product in the Network Switches category. This manual has pages.

Related Manuals

Buffalo 5210DN Manual

Buffalo TeraStation 5210DN Manual

Buffalo TeraStation 5210DF Manual

Buffalo 5210DF Manual

613-50137-01 Rev A

CentreCOM® FS980M Series

FAST ETHERNET MANAGED ACCESS SWITCHES

Command Reference for

AlliedWare Plus™ Version 5.4.6-2.x

FS980M/9

FS980M/9PS

FS980M/18

FS980M/18PS

FS980M/28

FS980M/28PS

FS980M/52

FS980M/52PS

Acknowledgments

This product includes software developed by the University of California, Berkeley and its contributors.

This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. For information about this see

www.openssl.org/

This product includes software licensed under v2 and v3 of the GNU General Public License, available from: www.gnu.org/licenses/

gpl2.html and www.gnu.org/licenses/gpl.html respectively.

Source code for all GPL licensed software in this product can be obtained from the Allied Telesis GPL Code Download Center at:

www.alliedtelesis.com/support/

Allied Telesis is committed to meeting the requirements of the open source licenses including the GNU General Public License (GPL) and

will make all required source code available.

If you would like a copy of the GPL source code contained in Allied Telesis products, please send us a request by registered mail including

a check for US$15 to cover production and shipping costs and a CD with the GPL code will be mailed to you.

GPL Code Request

Allied Telesis Labs (Ltd)

PO Box 8011

Christchurch

New Zealand

Allied Telesis, AlliedWare Plus, Allied Telesis Management Framework, EPSRing, SwitchBlade, VCStack, and VCStack Plus are trademarks or

registered trademarks in the United States and elsewhere of Allied Telesis, Inc.

Microsoft and Internet Explorer are registered trademarks of Microsoft Corporation. All other product names, company names, logos or

other designations mentioned herein may be trademarks or registered trademarks of their respective owners.

 2017 Allied Telesis, Inc.

Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document without prior

written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for any

incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this

manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the possibility

of such damages.

613-50137-01 Rev A Command Reference for FS980M Series 3

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Contents

PART 1: Setup and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Chapter 1: CLI Navigation Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

configure terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

disable (Privileged Exec mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

enable (Privileged Exec mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

logout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

show history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Chapter 2: File and Configuration Management Commands . . . . . . . . . . . . . . . 70

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

autoboot enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74

boot config-file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

boot config-file backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77

boot system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78

boot system backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

cd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

copy (filename) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82

copy current-software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84

copy debug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85

copy running-config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

copy startup-config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87

copy zmodem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

create autoboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90

delete debug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

dir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92

edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94

edit (filename) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95

613-50137-01 Rev A Command Reference for FS980M Series 4

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

erase startup-config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

ip tftp source-interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97

ipv6 tftp source-interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98

mkdir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99

move . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

move debug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

pwd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

rmdir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

show autoboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

show boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

show file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

show file systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

show running-config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

show running-config interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

show startup-config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

show version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

write file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

write memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

write terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

Chapter 3: User Access Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

clear line console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

clear line vty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

enable password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

enable secret . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

exec-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

flowcontrol hardware (asyn/console) . . . . . . . . . . . . . . . . . . . . . . . . 133

length (asyn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

privilege level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138

security-password history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

security-password forced-change . . . . . . . . . . . . . . . . . . . . . . . . . . 140

security-password lifetime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

security-password minimum-categories . . . . . . . . . . . . . . . . . . . . . . 142

security-password minimum-length . . . . . . . . . . . . . . . . . . . . . . . . . 143

security-password reject-expired-pwd . . . . . . . . . . . . . . . . . . . . . . . 144

security-password warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

service advanced-vty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

service password-encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

service telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148

show privilege . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

show security-password configuration . . . . . . . . . . . . . . . . . . . . . . . 150

show security-password user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151

show telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152

show users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153

telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154

telnet server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155

terminal length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156

terminal resize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157

username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158

613-50137-01 Rev A Command Reference for FS980M Series 5

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Chapter 4: GUI Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160

atmf topology-gui enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161

gui-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162

log event-host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164

service http . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165

show http . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166

Chapter 5: System Configuration and Monitoring Commands . . . . . . . . . . . . 167

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167

banner exec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

banner login (system) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171

banner motd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173

clock set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175

clock summer-time date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176

clock summer-time recurring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178

clock timezone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180

ecofriendly led . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181

findme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182

findme trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184

hostname . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185

no debug all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187

reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188

reload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189

show clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190

show cpu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192

show cpu history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195

show debugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198

show ecofriendly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199

show interface memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200

show memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202

show memory allocations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204

show memory history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206

show memory pools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208

show memory shared . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209

show process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210

show reboot history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213

show router-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214

show system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215

show system environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216

show system interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217

show system mac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218

show system serialnumber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219

show tech-support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220

speed (asyn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222

terminal monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224

undebug all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225

Chapter 6: Pluggables and Cabling Commands . . . . . . . . . . . . . . . . . . . . . . 226

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226

clear test cable-diagnostics tdr . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227

show system pluggable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228

613-50137-01 Rev A Command Reference for FS980M Series 6

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

show system pluggable detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230

show system pluggable diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . 233

show test cable-diagnostics tdr . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235

test cable-diagnostics tdr interface . . . . . . . . . . . . . . . . . . . . . . . . . . 236

Chapter 7: Logging Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237

clear exception log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239

clear log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240

clear log buffered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241

clear log permanent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242

default log buffered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243

default log console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244

default log email . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245

default log host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246

default log monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247

default log permanent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248

log buffered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249

log buffered (filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250

log buffered exclude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253

log buffered size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256

log console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257

log console (filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258

log console exclude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261

log email . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264

log email (filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265

log email exclude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268

log email time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271

log facility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273

log host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275

log host (filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277

log host exclude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280

log host source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283

log host time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284

log monitor (filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286

log monitor exclude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289

log permanent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292

log permanent (filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293

log permanent exclude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296

log permanent size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299

log-rate-limit nsm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300

log trustpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302

show counter log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303

show exception log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304

show log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305

show log config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307

show log permanent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309

show running-config log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311

Chapter 8: Scripting Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312

activate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313

613-50137-01 Rev A Command Reference for FS980M Series 7

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

echo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314

wait . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315

Chapter 9: Interface Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316

description (interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317

interface (to configure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318

mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320

show interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322

show interface brief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325

show interface memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326

show interface status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328

shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330

Chapter 10: Port Mirroring Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331

mirror interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332

show mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334

show mirror interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335

Chapter 11: Interface Testing Commands . . . . . . . . . . . . . . . . . . . . . . . . . . 336

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336

clear test interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337

service test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338

test interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339

PART 2: Layer Two Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341

Chapter 12: Switching Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342

backpressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344

clear loop-protection counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346

clear mac address-table dynamic . . . . . . . . . . . . . . . . . . . . . . . . . . . 347

clear mac address-table static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349

clear port counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350

clear port-security intrusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351

debug loopprot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354

debug platform packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355

duplex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357

flowcontrol (switch port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359

linkflap action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361

loop-protection loop-detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362

loop-protection action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363

loop-protection action-delay-time . . . . . . . . . . . . . . . . . . . . . . . . . . 364

loop-protection timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365

mac address-table acquire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366

mac address-table ageing-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367

mac address-table static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368

mac address-table thrash-limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369

platform jumboframe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370

platform stop-unreg-mc-flooding . . . . . . . . . . . . . . . . . . . . . . . . . . 371

613-50137-01 Rev A Command Reference for FS980M Series 8

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

polarity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373

show debugging loopprot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374

show debugging platform packet . . . . . . . . . . . . . . . . . . . . . . . . . . 375

show flowcontrol interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376

show interface err-disabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377

show interface switchport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378

show loop-protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379

show mac address-table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381

show mac address-table thrash-limit . . . . . . . . . . . . . . . . . . . . . . . . 383

show platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384

show platform classifier statistics utilization brief . . . . . . . . . . . . . . . . . 385

show platform port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386

show port-security interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391

show port-security intrusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392

show storm-control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393

speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394

storm-control level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396

switchport port-security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397

switchport port-security aging . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398

switchport port-security maximum . . . . . . . . . . . . . . . . . . . . . . . . . 399

switchport port-security violation . . . . . . . . . . . . . . . . . . . . . . . . . . 400

thrash-limiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401

undebug loopprot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402

undebug platform packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403

Chapter 13: VLAN Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404

private-vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406

private-vlan association . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407

show vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408

show vlan classifier group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409

show vlan classifier group interface . . . . . . . . . . . . . . . . . . . . . . . . . 410

show vlan classifier interface group . . . . . . . . . . . . . . . . . . . . . . . . . 411

show vlan classifier rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412

show vlan private-vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413

switchport access vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414

switchport enable vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415

switchport mode access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416

switchport mode private-vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417

switchport mode private-vlan trunk promiscuous . . . . . . . . . . . . . . . . 418

switchport mode private-vlan trunk secondary . . . . . . . . . . . . . . . . . . 420

switchport mode trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 422

switchport private-vlan host-association . . . . . . . . . . . . . . . . . . . . . . 423

switchport private-vlan mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . 424

switchport trunk allowed vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425

switchport trunk native vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 428

switchport voice dscp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429

switchport voice vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430

switchport voice vlan priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 432

vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433

vlan classifier activate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434

vlan classifier group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435

vlan classifier rule ipv4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436

613-50137-01 Rev A Command Reference for FS980M Series 9

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

vlan classifier rule proto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437

vlan database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440

vlan mode stack-local-vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 441

Chapter 14: Spanning Tree Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 443

clear spanning-tree statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445

clear spanning-tree detected protocols (RSTP and MSTP) . . . . . . . . . . . 446

debug mstp (RSTP and STP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 447

instance priority (MSTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451

instance vlan (MSTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 453

region (MSTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455

revision (MSTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456

show debugging mstp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457

show spanning-tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458

show spanning-tree brief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461

show spanning-tree mst . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 462

show spanning-tree mst config . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463

show spanning-tree mst detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464

show spanning-tree mst detail interface . . . . . . . . . . . . . . . . . . . . . . 466

show spanning-tree mst instance . . . . . . . . . . . . . . . . . . . . . . . . . . . 468

show spanning-tree mst instance interface . . . . . . . . . . . . . . . . . . . . 469

show spanning-tree mst interface . . . . . . . . . . . . . . . . . . . . . . . . . . 470

show spanning-tree mst detail interface . . . . . . . . . . . . . . . . . . . . . . 471

show spanning-tree statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473

show spanning-tree statistics instance . . . . . . . . . . . . . . . . . . . . . . . 475

show spanning-tree statistics instance interface . . . . . . . . . . . . . . . . . 476

show spanning-tree statistics interface . . . . . . . . . . . . . . . . . . . . . . . 478

show spanning-tree vlan range-index . . . . . . . . . . . . . . . . . . . . . . . . 480

spanning-tree autoedge (RSTP and MSTP) . . . . . . . . . . . . . . . . . . . . . 481

spanning-tree bpdu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 482

spanning-tree cisco-interoperability (MSTP) . . . . . . . . . . . . . . . . . . . . 484

spanning-tree edgeport (RSTP and MSTP) . . . . . . . . . . . . . . . . . . . . . 485

spanning-tree enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 486

spanning-tree errdisable-timeout enable . . . . . . . . . . . . . . . . . . . . . . 488

spanning-tree errdisable-timeout interval . . . . . . . . . . . . . . . . . . . . . 489

spanning-tree force-version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490

spanning-tree forward-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 491

spanning-tree guard root . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 492

spanning-tree hello-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 493

spanning-tree link-type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 494

spanning-tree max-age . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495

spanning-tree max-hops (MSTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . 496

spanning-tree mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 497

spanning-tree mst configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 498

spanning-tree mst instance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499

spanning-tree mst instance path-cost . . . . . . . . . . . . . . . . . . . . . . . . 500

spanning-tree mst instance priority . . . . . . . . . . . . . . . . . . . . . . . . . 502

spanning-tree mst instance restricted-role . . . . . . . . . . . . . . . . . . . . . 503

spanning-tree mst instance restricted-tcn . . . . . . . . . . . . . . . . . . . . . 505

spanning-tree path-cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 506

spanning-tree portfast (STP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507

spanning-tree portfast bpdu-filter . . . . . . . . . . . . . . . . . . . . . . . . . . 509

613-50137-01 Rev A Command Reference for FS980M Series 10

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

spanning-tree portfast bpdu-guard . . . . . . . . . . . . . . . . . . . . . . . . . 511

spanning-tree priority (bridge priority) . . . . . . . . . . . . . . . . . . . . . . . 513

spanning-tree priority (port priority) . . . . . . . . . . . . . . . . . . . . . . . . . 514

spanning-tree restricted-role . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515

spanning-tree restricted-tcn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516

spanning-tree transmit-holdcount . . . . . . . . . . . . . . . . . . . . . . . . . . 517

undebug mstp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518

Chapter 15: Link Aggregation Commands . . . . . . . . . . . . . . . . . . . . . . . . . . 519

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 519

channel-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 521

clear lacp counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523

debug lacp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524

lacp global-passive-mode enable . . . . . . . . . . . . . . . . . . . . . . . . . . . 525

lacp port-priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 526

lacp system-priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 527

lacp timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 528

show debugging lacp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530

show diagnostic channel-group . . . . . . . . . . . . . . . . . . . . . . . . . . . 531

show etherchannel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 532

show etherchannel detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 533

show etherchannel summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 534

show lacp sys-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 535

show lacp-counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 536

show port etherchannel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 537

show static-channel-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 538

static-channel-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 539

undebug lacp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541

Chapter 16: Power over Ethernet Commands . . . . . . . . . . . . . . . . . . . . . . . . 542

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 542

clear power-inline counters interface . . . . . . . . . . . . . . . . . . . . . . . . 544

debug power-inline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545

power-inline allow-legacy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 547

power-inline description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 548

power-inline enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 549

power-inline max . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550

power-inline priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 552

power-inline usage-threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 554

service power-inline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 555

show debugging power-inline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556

show power-inline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 557

show power-inline counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 560

show power-inline interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 562

show power-inline interface detail . . . . . . . . . . . . . . . . . . . . . . . . . . 564

PART 3: Layer Three, Switching and Routing . . . . . . . . . . . . . . . . . . . . . . 567

Chapter 17: IP Addressing and Protocol Commands . . . . . . . . . . . . . . . . . . . . 568

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 568

arp-aging-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 570

arp (IP address MAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 571

613-50137-01 Rev A Command Reference for FS980M Series 11

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

arp log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 572

arp-reply-bc-dmac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 575

clear arp-cache . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 576

debug ip packet interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 577

ip address (IP Addressing and Protocol) . . . . . . . . . . . . . . . . . . . . . . . 579

ip gratuitous-arp-link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 581

ip limited-local-proxy-arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 583

ip local-proxy-arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 584

ip proxy-arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 585

local-proxy-arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 586

ip unreachables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587

ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 589

show arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 590

show debugging ip packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 592

show ip interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 594

show ip sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 595

show ip traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 598

tcpdump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 604

traceroute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 605

undebug ip packet interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 606

Chapter 18: Domain Name Service (DNS) Commands . . . . . . . . . . . . . . . . . . . 607

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 607

ip domain-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 608

ip domain-lookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 609

ip domain-name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610

ip name-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 611

show hosts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 613

show ip domain-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 614

show ip domain-name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 615

show ip name-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 616

Chapter 19: IPv6 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 617

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 617

clear ipv6 neighbors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 618

ipv6 address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 619

ipv6 enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 620

ipv6 nd raguard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 621

ipv6 neighbor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 623

ipv6 route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 624

ipv6 unreachables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625

ping ipv6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 626

show ipv6 interface brief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 627

show ipv6 neighbors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 628

show ipv6 route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 629

show ipv6 route summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 631

traceroute ipv6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 632

Chapter 20: Routing Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 633

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 633

ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 634

ipv6 route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 636

613-50137-01 Rev A Command Reference for FS980M Series 12

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

maximum-paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 637

show ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 638

show ip route database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 640

show ip route summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 641

show ipv6 route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 642

show ipv6 route summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 644

Chapter 21: RIP Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 645

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 645

accept-lifetime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 647

alliedware-behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 649

cisco-metric-behavior (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 651

clear ip rip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 652

debug rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 653

default-information originate (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . 654

default-metric (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 655

distance (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 656

distribute-list (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 657

fullupdate (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 658

ip rip authentication key-chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . 659

ip rip authentication mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 661

ip rip authentication string . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 664

ip rip receive-packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 666

ip rip receive version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 667

ip rip send-packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 668

ip rip send version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 669

ip rip send version 1-compatible . . . . . . . . . . . . . . . . . . . . . . . . . . . 671

ip rip split-horizon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 673

key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 674

key chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 675

key-string . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 676

maximum-prefix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 677

neighbor (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 678

network (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 679

offset-list (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 680

passive-interface (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 681

recv-buffer-size (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682

redistribute (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 683

restart rip graceful . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 684

rip restart grace-period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 685

route (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 686

router rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 687

send-lifetime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 688

show debugging rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 690

show ip protocols rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 691

show ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 692

show ip rip database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693

show ip rip interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 694

timers (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 695

undebug rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 696

version (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 697

613-50137-01 Rev A Command Reference for FS980M Series 13

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PART 4: Multicast Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 698

Chapter 22: IGMP Snooping Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . 699

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 699

clear ip igmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 701

clear ip igmp group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 702

clear ip igmp interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 703

debug igmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 704

ip igmp flood specific-query . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 705

ip igmp maximum-groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 706

ip igmp snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 708

ip igmp snooping fast-leave . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 709

ip igmp snooping mrouter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 710

ip igmp snooping querier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 711

ip igmp snooping report-suppression . . . . . . . . . . . . . . . . . . . . . . . . 712

ip igmp snooping routermode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 713

ip igmp snooping tcn query solicit . . . . . . . . . . . . . . . . . . . . . . . . . . 715

ip igmp static-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 717

ip igmp trusted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 719

ip igmp version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 720

show debugging igmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 721

show ip igmp groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 722

show ip igmp interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 724

show ip igmp snooping mrouter . . . . . . . . . . . . . . . . . . . . . . . . . . . 726

show ip igmp snooping routermode . . . . . . . . . . . . . . . . . . . . . . . . . 727

show ip igmp snooping statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . 728

undebug igmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 730

Chapter 23: MLD Snooping Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 731

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 731

clear ipv6 mld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 732

clear ipv6 mld group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 733

clear ipv6 mld interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 734

debug mld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 735

ipv6 mld access-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 736

ipv6 mld immediate-leave . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 737

ipv6 mld limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 738

ipv6 mld snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 740

ipv6 mld snooping fast-leave . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 742

ipv6 mld snooping mrouter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 743

ipv6 mld snooping querier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 745

ipv6 mld snooping report-suppression . . . . . . . . . . . . . . . . . . . . . . . 746

ipv6 mld static-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 748

show debugging mld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 750

show ipv6 mld groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 751

show ipv6 mld interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 752

show ipv6 mld snooping mrouter . . . . . . . . . . . . . . . . . . . . . . . . . . 753

show ipv6 mld snooping statistics . . . . . . . . . . . . . . . . . . . . . . . . . . 754

PART 5: Access and Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 755

Chapter 24: IPv4 Hardware Access Control List (ACL) Commands . . . . . . . . . . . 756

613-50137-01 Rev A Command Reference for FS980M Series 14

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 756

access-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 759

access-list (numbered hardware ACL for ICMP) . . . . . . . . . . . . . . . . . . 761

access-list (numbered hardware ACL for IP packets) . . . . . . . . . . . . . . . 764

access-list (numbered hardware ACL for IP protocols) . . . . . . . . . . . . . . 767

access-list (numbered hardware ACL for MAC addresses) . . . . . . . . . . . 771

access-list (numbered hardware ACL for TCP or UDP) . . . . . . . . . . . . . . 773

access-list hardware (named hardware ACL) . . . . . . . . . . . . . . . . . . . . 776

(named hardware ACL: ICMP entry) . . . . . . . . . . . . . . . . . . . . . . . . . 778

(named hardware ACL: IP packet entry) . . . . . . . . . . . . . . . . . . . . . . . 782

(named hardware ACL: IP protocol entry) . . . . . . . . . . . . . . . . . . . . . . 786

(named hardware ACL: MAC entry) . . . . . . . . . . . . . . . . . . . . . . . . . . 791

(named hardware ACL: TCP or UDP entry) . . . . . . . . . . . . . . . . . . . . . 794

commit (IPv4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 797

show access-list (IPv4 Hardware ACLs) . . . . . . . . . . . . . . . . . . . . . . . 798

show interface access-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800

Chapter 25: IPv4 Software Access Control List (ACL) Commands . . . . . . . . . . . . 801

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 801

access-list extended (named) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 804

access-list (extended numbered) . . . . . . . . . . . . . . . . . . . . . . . . . . . 812

(access-list extended ICMP filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . 814

(access-list extended IP filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 816

(access-list extended IP protocol filter) . . . . . . . . . . . . . . . . . . . . . . . 819

(access-list extended TCP UDP filter) . . . . . . . . . . . . . . . . . . . . . . . . . 823

access-list standard (named) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 825

access-list (standard numbered) . . . . . . . . . . . . . . . . . . . . . . . . . . . 827

(access-list standard named filter) . . . . . . . . . . . . . . . . . . . . . . . . . . 829

(access-list standard numbered filter) . . . . . . . . . . . . . . . . . . . . . . . . 831

clear ip prefix-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 833

ip prefix-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 834

maximum-access-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 836

show access-list (IPv4 Software ACLs) . . . . . . . . . . . . . . . . . . . . . . . . 837

show ip access-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 839

show ip prefix-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 840

vty access-class (numbered) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 841

Chapter 26: IPv6 Software Access Control List (ACL) Commands . . . . . . . . . . . . 842

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 842

ipv6 access-list standard (named) . . . . . . . . . . . . . . . . . . . . . . . . . . . 844

(ipv6 access-list standard filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 846

show ipv6 access-list (IPv6 Software ACLs) . . . . . . . . . . . . . . . . . . . . . 848

vty ipv6 access-class (named) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 849

Chapter 27: QoS Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 850

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 850

class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 852

class-map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 853

clear mls qos interface policer-counters . . . . . . . . . . . . . . . . . . . . . . . 854

default-action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 855

description (QoS policy-map) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 856

match access-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 857

613-50137-01 Rev A Command Reference for FS980M Series 15

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

match cos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 859

match dscp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 860

match eth-format protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 861

match ip-precedence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 864

match mac-type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 865

match tcp-flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 866

match vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 867

mls qos cos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 868

mls qos enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 869

mls qos map cos-queue to . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 870

mls qos map premark-dscp to . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 871

no police . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 872

police single-rate action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 873

police twin-rate action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 874

policy-map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 876

priority-queue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 877

remark-map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 878

remark new-cos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 880

service-policy input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 882

show class-map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 883

show mls qos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 884

show mls qos interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 885

show mls qos interface policer-counters . . . . . . . . . . . . . . . . . . . . . . 888

show mls qos interface queue-counters . . . . . . . . . . . . . . . . . . . . . . 889

show mls qos interface storm-status . . . . . . . . . . . . . . . . . . . . . . . . . 890

show mls qos maps cos-queue . . . . . . . . . . . . . . . . . . . . . . . . . . . . 891

show mls qos maps premark-dscp . . . . . . . . . . . . . . . . . . . . . . . . . . 892

show platform classifier statistics utilization brief . . . . . . . . . . . . . . . . . 893

show policy-map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 894

storm-action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 895

storm-downtime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 896

storm-protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 897

storm-rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 898

storm-window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 899

trust dscp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 900

wrr-queue disable queues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 901

wrr-queue egress-rate-limit queues . . . . . . . . . . . . . . . . . . . . . . . . . 902

wrr-queue weight queues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 903

Chapter 28: 802.1X Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 904

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 904

debug dot1x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 906

dot1x control-direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 907

dot1x eap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 909

dot1x eapol-version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 910

dot1x initialize interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 912

dot1x initialize supplicant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 913

dot1x keytransmit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 914

dot1x max-auth-fail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 915

dot1x max-reauth-req . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 917

dot1x port-control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 919

dot1x timeout tx-period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 921

show debugging dot1x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 923

613-50137-01 Rev A Command Reference for FS980M Series 16

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

show dot1x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 924

show dot1x diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 927

show dot1x interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 929

show dot1x sessionstatistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 934

show dot1x statistics interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 935

show dot1x supplicant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 936

show dot1x supplicant interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 938

undebug dot1x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 941

Chapter 29: Authentication Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 942

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 942

auth auth-fail vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 945

auth critical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 947

auth dynamic-vlan-creation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 948

auth guest-vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 951

auth guest-vlan forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 954

auth host-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 956

auth log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 958

auth max-supplicant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 960

auth profile (Global Configuration) . . . . . . . . . . . . . . . . . . . . . . . . . . 962

auth profile (Interface Configuration) . . . . . . . . . . . . . . . . . . . . . . . . 963

auth reauthentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 964

auth roaming disconnected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 965

auth roaming enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 967

auth supplicant-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 969

auth supplicant-mac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 971

auth timeout connect-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . 974

auth timeout quiet-period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 976

auth timeout reauth-period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 977

auth timeout server-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 979

auth timeout supp-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 981

auth two-step enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 983

auth-mac enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 986

auth-mac method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 988

auth-mac password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 990

auth-mac reauth-relearning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 991

auth-mac username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 992

auth-web enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 993

auth-web forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 995

auth-web max-auth-fail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 998

auth-web method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000

auth-web-server blocking-mode . . . . . . . . . . . . . . . . . . . . . . . . . . 1001

auth-web-server dhcp ipaddress . . . . . . . . . . . . . . . . . . . . . . . . . . 1002

auth-web-server dhcp lease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1003

auth-web-server dhcp-wpad-option . . . . . . . . . . . . . . . . . . . . . . . . 1004

auth-web-server host-name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1005

auth-web-server intercept-port . . . . . . . . . . . . . . . . . . . . . . . . . . . 1006

auth-web-server ipaddress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1007

auth-web-server page language . . . . . . . . . . . . . . . . . . . . . . . . . . 1008

auth-web-server login-url . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1009

auth-web-server page logo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1010

auth-web-server page sub-title . . . . . . . . . . . . . . . . . . . . . . . . . . . 1011

auth-web-server page success-message . . . . . . . . . . . . . . . . . . . . . 1012

613-50137-01 Rev A Command Reference for FS980M Series 17

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

auth-web-server page title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1013

auth-web-server page welcome-message . . . . . . . . . . . . . . . . . . . . 1014

auth-web-server ping-poll enable . . . . . . . . . . . . . . . . . . . . . . . . . 1015

auth-web-server ping-poll failcount . . . . . . . . . . . . . . . . . . . . . . . . 1016

auth-web-server ping-poll interval . . . . . . . . . . . . . . . . . . . . . . . . . 1017

auth-web-server ping-poll reauth-timer-refresh . . . . . . . . . . . . . . . . 1018

auth-web-server ping-poll timeout . . . . . . . . . . . . . . . . . . . . . . . . . 1019

auth-web-server port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1020

auth-web-server redirect-delay-time . . . . . . . . . . . . . . . . . . . . . . . 1021

auth-web-server redirect-url . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1022

auth-web-server session-keep . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1023

auth-web-server ssl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1024

auth-web-server ssl intercept-port . . . . . . . . . . . . . . . . . . . . . . . . . 1025

copy proxy-autoconfig-file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1026

copy web-auth-https-file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1027

description (Authentication Profile) . . . . . . . . . . . . . . . . . . . . . . . . 1028

erase proxy-autoconfig-file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1029

erase web-auth-https-file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1030

platform l3-vlan-hashing-algorithm . . . . . . . . . . . . . . . . . . . . . . . . 1031

platform mac-vlan-hashing-algorithm . . . . . . . . . . . . . . . . . . . . . . . 1032

show auth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1033

show auth diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1035

show auth interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1037

show auth sessionstatistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1040

show auth statistics interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1041

show auth supplicant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1042

show auth supplicant interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 1045

show auth two-step supplicant brief . . . . . . . . . . . . . . . . . . . . . . . . 1046

show auth-web-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1047

show auth-web-server page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1048

show proxy-autoconfig-file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1049

Chapter 30: AAA Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1050

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1050

aaa accounting auth-mac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1052

aaa accounting auth-web . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1054

aaa accounting commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1056

aaa accounting dot1x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1058

aaa accounting login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1060

aaa accounting update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1063

aaa authentication auth-mac . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1065

aaa authentication auth-web . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1067

aaa authentication dot1x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1068

aaa authentication enable default group tacacs+ . . . . . . . . . . . . . . . 1069

aaa authentication enable default local . . . . . . . . . . . . . . . . . . . . . . 1071

aaa authentication login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1072

aaa authorization commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1074

aaa authorization config-commands . . . . . . . . . . . . . . . . . . . . . . . . 1076

aaa group server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1077

aaa local authentication attempts lockout-time . . . . . . . . . . . . . . . . . 1079

aaa local authentication attempts max-fail . . . . . . . . . . . . . . . . . . . . 1080

aaa login fail-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1081

accounting login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1082

613-50137-01 Rev A Command Reference for FS980M Series 18

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

authorization commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1083

clear aaa local user lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1085

debug aaa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1086

proxy-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1088

radius-secure-proxy aaa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1089

server (radsecproxy-aaa) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1090

server mutual-authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1092

server name-check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1093

server trustpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1094

show aaa local user locked . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1096

show debugging aaa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1097

undebug aaa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1098

Chapter 31: RADIUS Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1099

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1099

auth radius send nas-identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . 1100

auth radius send service-type . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1101

deadtime (RADIUS server group) . . . . . . . . . . . . . . . . . . . . . . . . . . 1102

debug radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1103

ip radius source-interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1104

radius-server deadtime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1105

radius-server host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1106

radius-server key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1109

radius-server retransmit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1110

radius-server timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1112

server (Server Group) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1114

show debugging radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1116

show radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1117

show radius statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1120

undebug radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1121

Chapter 32: Public Key Infrastructure Commands . . . . . . . . . . . . . . . . . . . . 1122

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1122

crypto key generate rsa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1123

crypto key zeroize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1124

crypto pki authenticate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1125

crypto pki enroll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1126

crypto pki enroll user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1127

crypto pki export pem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1129

crypto pki export pkcs12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1130

crypto pki import pem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1132

crypto pki import pkcs12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1134

crypto pki trustpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1135

enrollment (trustpoint configuration mode) . . . . . . . . . . . . . . . . . . . 1136

fingerprint (trustpoint configuration mode) . . . . . . . . . . . . . . . . . . . 1137

no crypto pki certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1139

rsakeypair (trustpoint configuration mode) . . . . . . . . . . . . . . . . . . . 1140

show crypto key mypubkey rsa . . . . . . . . . . . . . . . . . . . . . . . . . . . 1141

show crypto pki certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1142

show crypto pki enrollment user . . . . . . . . . . . . . . . . . . . . . . . . . . 1144

show crypto pki trustpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1145

613-50137-01 Rev A Command Reference for FS980M Series 19

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

subject-name (trustpoint configuration) . . . . . . . . . . . . . . . . . . . . . 1146

Chapter 33: TACACS+ Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1148

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1148

authorization commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1149

aaa authorization commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1151

aaa authorization config-commands . . . . . . . . . . . . . . . . . . . . . . . . 1153

ip tacacs source-interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1154

show tacacs+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1155

tacacs-server host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1157

tacacs-server key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1159

tacacs-server timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1160

Chapter 34: DHCP Snooping Commands . . . . . . . . . . . . . . . . . . . . . . . . . . 1161

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1161

arp security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1163

arp security violation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1164

clear arp security statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1166

clear ip dhcp snooping binding . . . . . . . . . . . . . . . . . . . . . . . . . . . 1167

clear ip dhcp snooping statistics . . . . . . . . . . . . . . . . . . . . . . . . . . 1168

debug arp security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1169

debug ip dhcp snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1170

ip dhcp snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1171

ip dhcp snooping agent-option . . . . . . . . . . . . . . . . . . . . . . . . . . . 1172

ip dhcp snooping agent-option allow-untrusted . . . . . . . . . . . . . . . . 1173

ip dhcp snooping agent-option circuit-id vlantriplet . . . . . . . . . . . . . 1174

ip dhcp snooping agent-option remote-id . . . . . . . . . . . . . . . . . . . . 1175

ip dhcp snooping binding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1176

ip dhcp snooping database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1177

ip dhcp snooping delete-by-client . . . . . . . . . . . . . . . . . . . . . . . . . 1178

ip dhcp snooping delete-by-linkdown . . . . . . . . . . . . . . . . . . . . . . 1179

ip dhcp snooping max-bindings . . . . . . . . . . . . . . . . . . . . . . . . . . 1180

ip dhcp snooping subscriber-id . . . . . . . . . . . . . . . . . . . . . . . . . . . 1181

ip dhcp snooping trust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1182

ip dhcp snooping verify mac-address . . . . . . . . . . . . . . . . . . . . . . . 1183

ip dhcp snooping violation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1184

ip source binding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1185

service dhcp-snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1187

show arp security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1189

show arp security interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1190

show arp security statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1192

show debugging arp security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1194

show debugging ip dhcp snooping . . . . . . . . . . . . . . . . . . . . . . . . 1195

show ip dhcp snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1196

show ip dhcp snooping acl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1197

show ip dhcp snooping agent-option . . . . . . . . . . . . . . . . . . . . . . . 1200

show ip dhcp snooping binding . . . . . . . . . . . . . . . . . . . . . . . . . . 1202

show ip dhcp snooping interface . . . . . . . . . . . . . . . . . . . . . . . . . . 1204

show ip dhcp snooping statistics . . . . . . . . . . . . . . . . . . . . . . . . . . 1206

show ip source binding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1209

PART 6: Network Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1210

613-50137-01 Rev A Command Reference for FS980M Series 20

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Chapter 35: Virtual Chassis Stacking (VCStack™) Commands . . . . . . . . . . . . . 1211

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1211

clear counter stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1213

debug stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1214

reboot rolling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1215

reload rolling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1216

remote-login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1217

show counter stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1218

show debugging stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1222

show running-config stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1223

show provisioning (stack) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1224

show stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1225

show stack detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1227

show stack resiliencylink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1231

stack disabled-master-monitoring . . . . . . . . . . . . . . . . . . . . . . . . . 1233

stack enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1234

stack management subnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1236

stack management vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1237

stack priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1238

stack renumber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1239

stack renumber cascade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1240

stack resiliencylink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1242

stack software-auto-synchronize . . . . . . . . . . . . . . . . . . . . . . . . . . 1244

stack virtual-chassis-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1245

stack virtual-mac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1246

switch provision (stack) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1247

switchport resiliencylink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1249

vlan mode stack-local-vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1250

undebug stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1252

Chapter 36: Ethernet Protection Switched Ring (EPSRing™) Commands . . . . . . 1253

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1253

debug epsr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1255

epsr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1256

epsr configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1257

epsr datavlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1258

epsr enhancedrecovery enable . . . . . . . . . . . . . . . . . . . . . . . . . . . 1259

epsr mode master controlvlan primary port . . . . . . . . . . . . . . . . . . . 1260

epsr mode transit controlvlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1261

epsr priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1262

epsr state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1263

epsr trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1264

show debugging epsr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1265

show epsr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1266

show epsr common segments . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1271

show epsr config-check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1272

show epsr <epsr-instance> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1273

show epsr <epsr-instance> counters . . . . . . . . . . . . . . . . . . . . . . . 1274

show epsr counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1275

show epsr summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1276

undebug epsr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1277

613-50137-01 Rev A Command Reference for FS980M Series 21

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Chapter 37: RRP Snooping Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . 1278

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1278

ip rrp snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1279

show ip rrp snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1280

PART 7: Network Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1281

Chapter 38: Allied Telesis Management Framework™ (AMF) Commands . . . . . . 1282

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1282

atmf area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1286

atmf area password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1288

atmf backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1290

atmf backup area-masters delete . . . . . . . . . . . . . . . . . . . . . . . . . . 1291

atmf backup area-masters enable . . . . . . . . . . . . . . . . . . . . . . . . . 1292

atmf backup area-masters now . . . . . . . . . . . . . . . . . . . . . . . . . . . 1293

atmf backup area-masters synchronize . . . . . . . . . . . . . . . . . . . . . . 1294

atmf backup bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1295

atmf backup delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1296

atmf backup enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1297

atmf backup guests delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1298

atmf backup guests enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1299

atmf backup guests now . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1300

atmf backup guests synchronize . . . . . . . . . . . . . . . . . . . . . . . . . . 1301

atmf backup now . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1302

atmf backup redundancy enable . . . . . . . . . . . . . . . . . . . . . . . . . . 1304

atmf backup server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1305

atmf backup stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1307

atmf backup synchronize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1308

atmf cleanup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1309

atmf controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1310

atmf distribute firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1311

atmf domain vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1313

atmf enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1315

atmf group (membership) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1316

atmf guest-class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1318

atmf log-verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1320

atmf management subnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1321

atmf management vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1323

atmf master . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1324

atmf mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1325

atmf network-name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1326

atmf provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1327

atmf provision node clone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1328

atmf provision node configure boot config . . . . . . . . . . . . . . . . . . . 1330

atmf provision node configure boot system . . . . . . . . . . . . . . . . . . . 1331

atmf provision node create . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1332

atmf provision node delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1334

atmf provision node license-cert . . . . . . . . . . . . . . . . . . . . . . . . . . 1336

atmf provision node locate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1338

atmf reboot-rolling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1339

atmf recover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1343

atmf recover guest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1345

613-50137-01 Rev A Command Reference for FS980M Series 22

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

atmf recover led-off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1346

atmf remote-login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1347

atmf restricted-login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1349

atmf select-area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1351

atmf virtual-link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1352

atmf working-set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1354

clear atmf links statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1356

debug atmf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1357

debug atmf packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1359

discovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1362

erase factory-default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1364

http-enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1365

modeltype . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1367

show atmf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1368

show atmf area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1372

show atmf area guests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1375

show atmf area guests-detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1377

show atmf area nodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1379

show atmf area nodes-detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1381

show atmf area summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1383

show atmf backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1384

show atmf backup area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1388

show atmf backup guest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1390

show atmf detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1392

show atmf group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1394

show atmf group members . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1396

show atmf guest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1398

show atmf links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1400

show atmf links detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1402

show atmf links guest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1411

show atmf links statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1414

show atmf memory (deprecated) . . . . . . . . . . . . . . . . . . . . . . . . . . 1417

show atmf nodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1418

show atmf provision nodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1420

show atmf tech . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1421

show atmf virtual-links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1424

show atmf working-set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1426

show debugging atmf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1427

show debugging atmf packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1428

show running-config atmf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1429

switchport atmf-agentlink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1430

switchport atmf-arealink remote-area . . . . . . . . . . . . . . . . . . . . . . . 1431

switchport atmf-crosslink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1433

switchport atmf-guestlink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1435

switchport atmf-link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1437

type atmf node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1438

undebug atmf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1441

username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1442

Chapter 39: Dynamic Host Configuration Protocol (DHCP) Commands . . . . . . . 1444

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1444

ip address dhcp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1445

show counter dhcp-client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1447

613-50137-01 Rev A Command Reference for FS980M Series 23

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

show dhcp lease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1448

Chapter 40: NTP Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1450

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1450

ntp access-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1451

ntp authenticate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1452

ntp authentication-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1453

ntp broadcastdelay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1454

ntp discard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1455

ntp master . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1456

ntp peer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1457

ntp restrict . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1459

ntp server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1461

ntp source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1463

ntp trusted-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1465

show counter ntp (deprecated) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1466

show ntp associations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1467

show ntp counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1469

show ntp counters associations . . . . . . . . . . . . . . . . . . . . . . . . . . . 1471

show ntp status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1473

Chapter 41: SNMP Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1474

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1474

debug snmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1476

show counter snmp-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1477

show debugging snmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1481

show running-config snmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1482

show snmp-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1483

show snmp-server community . . . . . . . . . . . . . . . . . . . . . . . . . . . 1484

show snmp-server group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1485

show snmp-server user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1486

show snmp-server view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1487

snmp trap link-status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1488

snmp trap link-status suppress . . . . . . . . . . . . . . . . . . . . . . . . . . . 1490

snmp-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1492

snmp-server community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1494

snmp-server contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1495

snmp-server enable trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1496

snmp-server engineID local . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1498

snmp-server engineID local reset . . . . . . . . . . . . . . . . . . . . . . . . . . 1500

snmp-server group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1501

snmp-server host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1503

snmp-server legacy-ifadminstatus . . . . . . . . . . . . . . . . . . . . . . . . . 1505

snmp-server location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1506

snmp-server source-interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1507

snmp-server startup-trap-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . 1508

snmp-server user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1509

snmp-server view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1512

undebug snmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1513

Chapter 42: LLDP Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1514

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1514

613-50137-01 Rev A Command Reference for FS980M Series 24

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

clear lldp statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1516

clear lldp table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1517

debug lldp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1518

lldp faststart-count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1520

lldp holdtime-multiplier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1521

lldp management-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1522

lldp med-notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1523

lldp med-tlv-select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1524

lldp non-strict-med-tlv-order-check . . . . . . . . . . . . . . . . . . . . . . . . 1527

lldp notification-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1528

lldp notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1529

lldp port-number-type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1530

lldp reinit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1531

lldp run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1532

lldp timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1533

lldp tlv-select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1534

lldp transmit receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1536

lldp tx-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1537

location civic-location configuration . . . . . . . . . . . . . . . . . . . . . . . . 1538

location civic-location identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . 1542

location civic-location-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1543

location coord-location configuration . . . . . . . . . . . . . . . . . . . . . . . 1544

location coord-location identifier . . . . . . . . . . . . . . . . . . . . . . . . . . 1546

location coord-location-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1547

location elin-location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1548

location elin-location-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1549

show debugging lldp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1550

show lldp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1552

show lldp interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1554

show lldp local-info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1556

show lldp neighbors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1561

show lldp neighbors detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1563

show lldp statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1567

show lldp statistics interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1569

show location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1571

Chapter 43: SMTP Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1573

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1573

debug mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1574

delete mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1575

mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1576

mail from . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1577

mail smtpserver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1578

show counter mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1579

show mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1580

undebug mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1581

Chapter 44: RMON Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1582

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1582

rmon alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1583

rmon collection history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1585

rmon collection stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1586

613-50137-01 Rev A Command Reference for FS980M Series 25

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

rmon event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1587

show rmon alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1588

show rmon event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1589

show rmon history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1591

show rmon statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1593

Chapter 45: Secure Shell (SSH) Commands . . . . . . . . . . . . . . . . . . . . . . . . . 1595

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1595

banner login (SSH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1597

clear ssh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1598

crypto key destroy hostkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1599

crypto key destroy userkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1600

crypto key generate hostkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1601

crypto key generate userkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1602

crypto key pubkey-chain knownhosts . . . . . . . . . . . . . . . . . . . . . . . 1603

crypto key pubkey-chain userkey . . . . . . . . . . . . . . . . . . . . . . . . . . 1605

debug ssh client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1607

debug ssh server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1608

service ssh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1609

show banner login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1611

show crypto key hostkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1612

show crypto key pubkey-chain knownhosts . . . . . . . . . . . . . . . . . . . 1613

show crypto key pubkey-chain userkey . . . . . . . . . . . . . . . . . . . . . . 1614

show crypto key userkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1615

show running-config ssh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1616

show ssh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1618

show ssh client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1620

show ssh server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1621

show ssh server allow-users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1623

show ssh server deny-users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1624

ssh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1625

ssh client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1627

ssh server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1629

ssh server allow-users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1631

ssh server authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1633

ssh server deny-users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1635

ssh server max-auth-tries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1637

ssh server resolve-host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1638

ssh server scp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1639

ssh server sftp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1640

undebug ssh client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1641

undebug ssh server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1642

Chapter 46: Trigger Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1643

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1643

active (trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1645

day . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1646

debug trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1648

description (trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1649

repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1650

script . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1651

show debugging trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1653

613-50137-01 Rev A Command Reference for FS980M Series 26

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

show running-config trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1654

show trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1655

test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1660

time (trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1661

trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1663

trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1664

trigger activate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1665

type atmf node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1666

type cpu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1669

type interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1670

type memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1671

type periodic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1672

type ping-poll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1673

type reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1674

type stack disabled-master . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1675

type stack link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1676

type stack master-fail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1677

type stack member . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1678

type time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1679

type usb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1680

undebug trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1681

Chapter 47: Ping-Polling Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1682

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1682

active (ping-polling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1684

clear ping-poll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1685

critical-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1686

debug ping-poll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1687

description (ping-polling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1688

fail-count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1689

ip (ping-polling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1690

length (ping-poll data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1691

normal-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1692

ping-poll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1693

sample-size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1694

show counter ping-poll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1696

show ping-poll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1698

source-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1702

timeout (ping polling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1704

up-count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1705

undebug ping-poll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1706

613-50137-01 Rev A Command Reference for FS980M Series 27

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

List of Commands

(access-list extended ICMP filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .814

(access-list extended IP filter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .816

(access-list extended IP protocol filter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .819

(access-list extended TCP UDP filter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .823

(access-list standard named filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .829

(access-list standard numbered filter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .831

(ipv6 access-list standard filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .846

(named hardware ACL: ICMP entry). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .778

(named hardware ACL: IP packet entry). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .782

(named hardware ACL: IP protocol entry) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .786

(named hardware ACL: MAC entry) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .791

(named hardware ACL: TCP or UDP entry) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .794

aaa accounting auth-mac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1052

aaa accounting auth-web . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1054

aaa accounting commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1056

aaa accounting dot1x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1058

aaa accounting login. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1060

aaa accounting update. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1063

aaa authentication auth-mac. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1065

aaa authentication auth-web. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1067

aaa authentication dot1x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1068

aaa authentication enable default group tacacs+ . . . . . . . . . . . . . . . . . . . . . . . 1069

aaa authentication enable default local. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1071

aaa authentication login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1072

aaa authorization commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1074

613-50137-01 Rev A Command Reference for FS980M Series 28

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

aaa authorization commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1151

aaa authorization config-commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1076

aaa authorization config-commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1153

aaa group server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1077

aaa local authentication attempts lockout-time. . . . . . . . . . . . . . . . . . . . . . . . . .1079

aaa local authentication attempts max-fail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1080

aaa login fail-delay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1081

accept-lifetime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 647

access-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 759

access-list (extended numbered) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 812

access-list (numbered hardware ACL for ICMP) . . . . . . . . . . . . . . . . . . . . . . . . . . . 761

access-list (numbered hardware ACL for IP packets). . . . . . . . . . . . . . . . . . . . . . . 764

access-list (numbered hardware ACL for IP protocols). . . . . . . . . . . . . . . . . . . . . 767

access-list (numbered hardware ACL for MAC addresses) . . . . . . . . . . . . . . . . . 771

access-list (numbered hardware ACL for TCP or UDP) . . . . . . . . . . . . . . . . . . . . . 773

access-list (standard numbered). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 827

access-list extended (named) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 804

access-list hardware (named hardware ACL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 776

access-list standard (named) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 825

accounting login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1082

activate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313

active (ping-polling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1684

active (trigger). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1645

alliedware-behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 649

arp (IP address MAC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 571

arp log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 572

arp security violation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1164

arp security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1163

arp-aging-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 570

arp-reply-bc-dmac. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 575

atmf area password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1288

atmf area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1286

atmf backup area-masters delete. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1291

atmf backup area-masters enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1292

atmf backup area-masters now. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1293

613-50137-01 Rev A Command Reference for FS980M Series 29

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

atmf backup area-masters synchronize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1294

atmf backup bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1295

atmf backup delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1296

atmf backup enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1297

atmf backup guests delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1298

atmf backup guests enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1299

atmf backup guests now. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1300

atmf backup guests synchronize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1301

atmf backup now. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1302

atmf backup redundancy enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1304

atmf backup server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1305

atmf backup stop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1307

atmf backup synchronize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1308

atmf backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1290

atmf cleanup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1309

atmf controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1310

atmf distribute firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1311

atmf domain vlan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1313

atmf enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1315

atmf group (membership) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1316

atmf guest-class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1318

atmf log-verbose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1320

atmf management subnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1321

atmf management vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1323

atmf master . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1324

atmf mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1325

atmf network-name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1326

atmf provision node clone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1328

atmf provision node configure boot config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1330

atmf provision node configure boot system . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1331

atmf provision node create . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1332

atmf provision node delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1334

atmf provision node license-cert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1336

atmf provision node locate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1338

atmf provision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1327

613-50137-01 Rev A Command Reference for FS980M Series 30

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

atmf reboot-rolling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1339

atmf recover guest. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1345

atmf recover led-off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1346

atmf recover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1343

atmf remote-login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1347

atmf restricted-login. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1349

atmf select-area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1351

atmf topology-gui enable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161

atmf virtual-link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1352

atmf working-set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1354

auth auth-fail vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 945

auth critical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 947

auth dynamic-vlan-creation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 948

auth guest-vlan forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 954

auth guest-vlan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 951

auth host-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 956

auth log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 958

auth max-supplicant. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 960

auth profile (Global Configuration) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 962

auth profile (Interface Configuration). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 963

auth radius send nas-identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1100

auth radius send service-type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1101

auth reauthentication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 964

auth roaming disconnected. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 965

auth roaming enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 967

auth supplicant-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 969

auth supplicant-mac. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 971

auth timeout connect-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 974

auth timeout quiet-period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 976

auth timeout reauth-period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 977

auth timeout server-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 979

auth timeout supp-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 981

auth two-step enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 983

auth-mac enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 986

auth-mac method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 988

613-50137-01 Rev A Command Reference for FS980M Series 31

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

auth-mac password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 990

auth-mac reauth-relearning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 991

auth-mac username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 992

authorization commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1083

authorization commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1149

auth-web enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 993

auth-web forward . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 995

auth-web max-auth-fail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 998

auth-web method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1000

auth-web-server blocking-mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1001

auth-web-server dhcp ipaddress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1002

auth-web-server dhcp lease. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1003

auth-web-server dhcp-wpad-option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1004

auth-web-server host-name. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1005

auth-web-server intercept-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1006

auth-web-server ipaddress. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1007

auth-web-server login-url . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1009

auth-web-server page language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1008

auth-web-server page logo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1010

auth-web-server page sub-title. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1011

auth-web-server page success-message. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1012

auth-web-server page title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1013

auth-web-server page welcome-message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1014

auth-web-server ping-poll enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1015

auth-web-server ping-poll failcount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1016

auth-web-server ping-poll interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1017

auth-web-server ping-poll reauth-timer-refresh . . . . . . . . . . . . . . . . . . . . . . . . .1018

auth-web-server ping-poll timeout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1019

auth-web-server port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1020

auth-web-server redirect-delay-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1021

auth-web-server redirect-url . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1022

auth-web-server session-keep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1023

auth-web-server ssl intercept-port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1025

auth-web-server ssl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1024

autoboot enable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

613-50137-01 Rev A Command Reference for FS980M Series 32

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

backpressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344

banner exec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

banner login (SSH). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1597

banner login (system). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171

banner motd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173

boot config-file backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

boot config-file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

boot system backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

boot system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

cd. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

channel-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 521

cisco-metric-behavior (RIP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 651

class. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 852

class-map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 853

clear aaa local user lockout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1085

clear arp security statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1166

clear arp-cache . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 576

clear atmf links statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1356

clear counter stack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1213

clear exception log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239

clear ip dhcp snooping binding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1167

clear ip dhcp snooping statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1168

clear ip igmp group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 702

clear ip igmp interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 703

clear ip igmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 701

clear ip prefix-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 833

clear ip rip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 652

clear ipv6 mld group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 733

clear ipv6 mld interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 734

clear ipv6 mld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 732

clear ipv6 neighbors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 618

clear lacp counters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523

clear line console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

clear line vty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

clear lldp statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1516

613-50137-01 Rev A Command Reference for FS980M Series 33

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

clear lldp table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1517

clear log buffered. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241

clear log permanent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242

clear log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240

clear loop-protection counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346

clear mac address-table dynamic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347

clear mac address-table static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349

clear mls qos interface policer-counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 854

clear ping-poll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1685

clear port counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350

clear port-security intrusion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351

clear power-inline counters interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544

clear spanning-tree detected protocols (RSTP and MSTP) . . . . . . . . . . . . . . . . . 446

clear spanning-tree statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445

clear ssh. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1598

clear test cable-diagnostics tdr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227

clear test interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337

clock set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175

clock summer-time date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176

clock summer-time recurring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178

clock timezone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180

commit (IPv4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 797

configure terminal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

copy (filename) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

copy current-software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

copy debug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

copy proxy-autoconfig-file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1026

copy running-config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

copy startup-config. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

copy web-auth-https-file. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1027

copy zmodem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

create autoboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

critical-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1686

crypto key destroy hostkey. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1599

crypto key destroy userkey. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1600

613-50137-01 Rev A Command Reference for FS980M Series 34

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

crypto key generate hostkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1601

crypto key generate rsa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1123

crypto key generate userkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1602

crypto key pubkey-chain knownhosts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1603

crypto key pubkey-chain userkey. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1605

crypto key zeroize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1124

crypto pki authenticate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1125

crypto pki enroll user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1127

crypto pki enroll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1126

crypto pki export pem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1129

crypto pki export pkcs12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1130

crypto pki import pem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1132

crypto pki import pkcs12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1134

crypto pki trustpoint. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1135

day. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1646

deadtime (RADIUS server group) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1102

debug aaa. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1086

debug arp security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1169

debug atmf packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1359

debug atmf. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1357

debug dot1x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 906

debug epsr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1255

debug igmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 704

debug ip dhcp snooping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1170

debug ip packet interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 577

debug lacp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524

debug lldp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1518

debug loopprot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354

debug mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1574

debug mld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 735

debug mstp (RSTP and STP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 447

debug ping-poll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1687

debug platform packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355

debug power-inline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545

debug radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1103

613-50137-01 Rev A Command Reference for FS980M Series 35

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

debug rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 653

debug snmp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1476

debug ssh client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1607

debug ssh server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1608

debug stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1214

debug trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1648

default log buffered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243

default log console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244

default log email . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245

default log host. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246

default log monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247

default log permanent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248

default-action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 855

default-information originate (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 654

default-metric (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 655

delete debug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

delete mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1575

delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

description (Authentication Profile) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1028

description (interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317

description (ping-polling). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1688

description (QoS policy-map) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 856

description (trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1649

dir. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

disable (Privileged Exec mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

discovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1362

distance (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 656

distribute-list (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 657

do. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

dot1x control-direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 907

dot1x eap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 909

dot1x eapol-version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 910

dot1x initialize interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 912

dot1x initialize supplicant. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 913

dot1x keytransmit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 914

613-50137-01 Rev A Command Reference for FS980M Series 36

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

dot1x max-auth-fail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 915

dot1x max-reauth-req . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 917

dot1x port-control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 919

dot1x timeout tx-period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 921

duplex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357

echo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314

ecofriendly led . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181

edit (filename). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

enable (Privileged Exec mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

enable password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

enable secret . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

end . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

enrollment (trustpoint configuration mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1136

epsr configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1257

epsr datavlan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1258

epsr enhancedrecovery enable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1259

epsr mode master controlvlan primary port . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1260

epsr mode transit controlvlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1261

epsr priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1262

epsr state. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1263

epsr trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1264

epsr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1256

erase factory-default. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1364

erase proxy-autoconfig-file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1029

erase startup-config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

erase web-auth-https-file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1030

exec-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

exit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

fail-count. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1689

findme trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184

findme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182

fingerprint (trustpoint configuration mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1137

flowcontrol (switch port). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359

flowcontrol hardware (asyn/console). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

613-50137-01 Rev A Command Reference for FS980M Series 37

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

fullupdate (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 658

gui-timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162

help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

hostname . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185

http-enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1365

instance priority (MSTP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451

instance vlan (MSTP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 453

interface (to configure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318

ip (ping-polling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1690

ip address (IP Addressing and Protocol) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 579

ip address dhcp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1445

ip dhcp snooping agent-option allow-untrusted. . . . . . . . . . . . . . . . . . . . . . . . .1173

ip dhcp snooping agent-option circuit-id vlantriplet . . . . . . . . . . . . . . . . . . . . .1174

ip dhcp snooping agent-option remote-id. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1175

ip dhcp snooping agent-option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1172

ip dhcp snooping binding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1176

ip dhcp snooping database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1177

ip dhcp snooping delete-by-client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1178

ip dhcp snooping delete-by-linkdown. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1179

ip dhcp snooping max-bindings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1180

ip dhcp snooping subscriber-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1181

ip dhcp snooping trust. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1182

ip dhcp snooping verify mac-address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1183

ip dhcp snooping violation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1184

ip dhcp snooping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1171

ip domain-list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 608

ip domain-lookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 609

ip domain-name. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610

ip gratuitous-arp-link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 581

ip igmp flood specific-query . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 705

ip igmp maximum-groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 706

ip igmp snooping fast-leave. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 709

ip igmp snooping mrouter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 710

ip igmp snooping querier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 711

ip igmp snooping report-suppression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 712

613-50137-01 Rev A Command Reference for FS980M Series 38

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

ip igmp snooping routermode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 713

ip igmp snooping tcn query solicit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 715

ip igmp snooping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 708

ip igmp static-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 717

ip igmp trusted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 719

ip igmp version. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 720

ip limited-local-proxy-arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 583

ip local-proxy-arp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 584

ip name-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 611

ip prefix-list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 834

ip proxy-arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 585

ip radius source-interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1104

ip rip authentication key-chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 659

ip rip authentication mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 661

ip rip authentication string. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 664

ip rip receive version. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 667

ip rip receive-packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 666

ip rip send version 1-compatible . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 671

ip rip send version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 669

ip rip send-packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 668

ip rip split-horizon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 673

ip route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 634

ip rrp snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1279

ip source binding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1185

ip tacacs source-interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1154

ip tftp source-interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

ip unreachables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587

ipv6 access-list standard (named) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 844

ipv6 address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 619

ipv6 enable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 620

ipv6 mld access-group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 736

ipv6 mld immediate-leave . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 737

ipv6 mld limit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 738

ipv6 mld snooping fast-leave . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 742

ipv6 mld snooping mrouter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 743

613-50137-01 Rev A Command Reference for FS980M Series 39

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

ipv6 mld snooping querier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 745

ipv6 mld snooping report-suppression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 746

ipv6 mld snooping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 740

ipv6 mld static-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 748

ipv6 nd raguard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 621

ipv6 neighbor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 623

ipv6 route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 624

ipv6 route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 636

ipv6 tftp source-interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

ipv6 unreachables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 625

key chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 675

key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 674

key-string . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 676

lacp global-passive-mode enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 525

lacp port-priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 526

lacp system-priority. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .527

lacp timeout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 528

length (asyn) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

length (ping-poll data). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1691

line. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136

linkflap action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361

lldp faststart-count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1520

lldp holdtime-multiplier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1521

lldp management-address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1522

lldp med-notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1523

lldp med-tlv-select. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1524

lldp non-strict-med-tlv-order-check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1527

lldp notification-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1528

lldp notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1529

lldp port-number-type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1530

lldp reinit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1531

lldp run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1532

lldp timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1533

lldp tlv-select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1534

lldp transmit receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1536

613-50137-01 Rev A Command Reference for FS980M Series 40

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

lldp tx-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1537

local-proxy-arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 586

location civic-location configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1538

location civic-location identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1542

location civic-location-id. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1543

location coord-location configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1544

location coord-location identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1546

location coord-location-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1547

location elin-location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1548

location elin-location-id. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1549

log buffered (filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250

log buffered exclude. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253

log buffered size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256

log buffered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249

log console (filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258

log console exclude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261

log console. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257

log email (filter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265

log email exclude. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268

log email time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271

log email . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264

log event-host. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164

log facility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273

log host (filter). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277

log host exclude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280

log host source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283

log host time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284

log host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275

log monitor (filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286

log monitor exclude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289

log permanent (filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293

log permanent exclude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296

log permanent size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299

log permanent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292

log trustpoint. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302

613-50137-01 Rev A Command Reference for FS980M Series 41

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

login authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1087

logout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

log-rate-limit nsm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300

loop-protection action. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363

loop-protection action-delay-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364

loop-protection loop-detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362

loop-protection timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365

mac address-table acquire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366

mac address-table ageing-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367

mac address-table static . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368

mac address-table thrash-limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369

mail from. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1577

mail smtpserver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1578

mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1576

match access-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 857

match cos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 859

match dscp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 860

match eth-format protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 861

match ip-precedence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 864

match mac-type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 865

match tcp-flags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 866

match vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 867

maximum-access-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 836

maximum-paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 637

maximum-prefix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 677

mirror interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332

mkdir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

mls qos cos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 868

mls qos enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 869

mls qos map cos-queue to . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 870

mls qos map premark-dscp to. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 871

modeltype . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1367

move debug. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

move. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

mtu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320

613-50137-01 Rev A Command Reference for FS980M Series 42

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

neighbor (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 678

network (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 679

no crypto pki certificate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1139

no debug all. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187

no police . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 872

normal-interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1692

ntp access-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1451

ntp authenticate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1452

ntp authentication-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1453

ntp broadcastdelay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1454

ntp discard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1455

ntp master . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1456

ntp peer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1457

ntp restrict . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1459

ntp server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1461

ntp source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1463

ntp trusted-key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1465

offset-list (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 680

passive-interface (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 681

ping ipv6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 626

ping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 589

ping-poll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1693

platform jumboframe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370

platform l3-vlan-hashing-algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1031

platform mac-vlan-hashing-algorithm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1032

platform stop-unreg-mc-flooding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371

polarity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373

police single-rate action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 873

police twin-rate action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 874

policy-map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 876

power-inline allow-legacy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 547

power-inline description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 548

power-inline enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 549

power-inline max. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550

power-inline priority. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 552

613-50137-01 Rev A Command Reference for FS980M Series 43

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

power-inline usage-threshold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 554

priority-queue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 877

private-vlan association. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407

private-vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406

privilege level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138

proxy-port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1088

pwd. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

radius-secure-proxy aaa. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1089

radius-server deadtime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1105

radius-server host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1106

radius-server key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1109

radius-server retransmit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1110

radius-server timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1112

reboot rolling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1215

reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188

recv-buffer-size (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 682

redistribute (RIP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 683

region (MSTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455

reload rolling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1216

reload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189

remark new-cos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 880

remark-map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 878

remote-login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1217

repeat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1650

restart rip graceful . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 684

revision (MSTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456

rip restart grace-period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 685

rmdir. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

rmon alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1583

rmon collection history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1585

rmon collection stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1586

rmon event. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1587

route (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 686

router rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 687

rsakeypair (trustpoint configuration mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1140

613-50137-01 Rev A Command Reference for FS980M Series 44

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

sample-size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1694

script. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1651

security-password forced-change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

security-password history. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

security-password lifetime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

security-password minimum-categories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

security-password minimum-length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

security-password reject-expired-pwd. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

security-password warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

send-lifetime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 688

server (radsecproxy-aaa) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1090

server (Server Group) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1114

server mutual-authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1092

server name-check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1093

server trustpoint. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1094

service advanced-vty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

service dhcp-snooping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1187

service http. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165

service password-encryption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147

service power-inline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 555

service ssh. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1609

service telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148

service test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338

service-policy input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 882

show aaa local user locked . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1096

show access-list (IPv4 Hardware ACLs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 798

show access-list (IPv4 Software ACLs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 837

show arp security interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1190

show arp security statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1192

show arp security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1189

show arp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 590

show atmf area guests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1375

show atmf area guests-detail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1377

show atmf area nodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1379

show atmf area nodes-detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1381

613-50137-01 Rev A Command Reference for FS980M Series 45

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

show atmf area summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1383

show atmf area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1372

show atmf backup area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1388

show atmf backup guest. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1390

show atmf backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1384

show atmf detail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1392

show atmf group members . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1396

show atmf group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1394

show atmf guest. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1398

show atmf links detail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1402

show atmf links guest. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1411

show atmf links statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1414

show atmf links. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1400

show atmf memory (deprecated). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1417

show atmf nodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1418

show atmf provision nodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1420

show atmf tech . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1421

show atmf virtual-links. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1424

show atmf working-set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1426

show atmf. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1368

show auth diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1035

show auth interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1037

show auth sessionstatistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1040

show auth statistics interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1041

show auth supplicant interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1045

show auth supplicant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1042

show auth two-step supplicant brief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1046

show auth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1033

show auth-web-server page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1048

show auth-web-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1047

show autoboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

show banner login. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1611

show boot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

show class-map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 883

show clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190

613-50137-01 Rev A Command Reference for FS980M Series 46

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

show counter dhcp-client. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1447

show counter log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303

show counter mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1579

show counter ntp (deprecated) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1466

show counter ping-poll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1696

show counter snmp-server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1477

show counter stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1218

show cpu history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195

show cpu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192

show crypto key hostkey. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1612

show crypto key mypubkey rsa. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1141

show crypto key pubkey-chain knownhosts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1613

show crypto key pubkey-chain userkey. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1614

show crypto key userkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1615

show crypto pki certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1142

show crypto pki enrollment user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1144

show crypto pki trustpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1145

show debugging aaa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1097

show debugging arp security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1194

show debugging atmf packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1428

show debugging atmf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1427

show debugging dot1x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 923

show debugging epsr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1265

show debugging igmp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 721

show debugging ip dhcp snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1195

show debugging ip packet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 592

show debugging lacp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530

show debugging lldp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1550

show debugging loopprot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374

show debugging mld . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 750

show debugging mstp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457

show debugging platform packet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375

show debugging power-inline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556

show debugging radius. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1116

show debugging rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 690

613-50137-01 Rev A Command Reference for FS980M Series 47

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

show debugging snmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1481

show debugging stack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1222

show debugging trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1653

show debugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198

show dhcp lease. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1448

show diagnostic channel-group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531

show dot1x diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 927

show dot1x interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 929

show dot1x sessionstatistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 934

show dot1x statistics interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 935

show dot1x supplicant interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 938

show dot1x supplicant. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 936

show dot1x. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 924

show ecofriendly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199

show epsr <epsr-instance> counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1274

show epsr <epsr-instance> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1273

show epsr common segments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1271

show epsr config-check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1272

show epsr counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1275

show epsr summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1276

show epsr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1266

show etherchannel detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 533

show etherchannel summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 534

show etherchannel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 532

show exception log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304

show file systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

show file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

show flowcontrol interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376

show history. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

show hosts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 613

show http . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166

show interface access-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800

show interface brief. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325

show interface err-disabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377

show interface memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200

613-50137-01 Rev A Command Reference for FS980M Series 48

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

show interface memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326

show interface status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328

show interface switchport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378

show interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322

show ip access-list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 839

show ip dhcp snooping acl. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1197

show ip dhcp snooping agent-option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1200

show ip dhcp snooping binding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1202

show ip dhcp snooping interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1204

show ip dhcp snooping statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1206

show ip dhcp snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1196

show ip domain-list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 614

show ip domain-name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 615

show ip igmp groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 722

show ip igmp interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 724

show ip igmp snooping mrouter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 726

show ip igmp snooping routermode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 727

show ip igmp snooping statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 728

show ip interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 594

show ip name-server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 616

show ip prefix-list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 840

show ip protocols rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 691

show ip rip database. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693

show ip rip interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 694

show ip rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 692

show ip route database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 640

show ip route summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 641

show ip route. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 638

show ip rrp snooping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1280

show ip sockets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 595

show ip source binding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1209

show ip traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 598

show ipv6 access-list (IPv6 Software ACLs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 848

show ipv6 interface brief. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 627

show ipv6 mld groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 751

613-50137-01 Rev A Command Reference for FS980M Series 49

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

show ipv6 mld interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 752

show ipv6 mld snooping mrouter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 753

show ipv6 mld snooping statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 754

show ipv6 neighbors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 628

show ipv6 route summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 631

show ipv6 route summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 644

show ipv6 route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 629

show ipv6 route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 642

show lacp sys-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 535

show lacp-counter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 536

show lldp interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1554

show lldp local-info. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1556

show lldp neighbors detail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1563

show lldp neighbors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1561

show lldp statistics interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1569

show lldp statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1567

show lldp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1552

show location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1571

show log config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307

show log permanent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309

show log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305

show loop-protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379

show mac address-table thrash-limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383

show mac address-table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381

show mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1580

show memory allocations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204

show memory history. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206

show memory pools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208

show memory shared. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209

show memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202

show mirror interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335

show mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334

show mls qos interface policer-counters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 888

show mls qos interface queue-counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 889

show mls qos interface storm-status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 890

613-50137-01 Rev A Command Reference for FS980M Series 50

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

show mls qos interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 885

show mls qos maps cos-queue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 891

show mls qos maps premark-dscp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 892

show mls qos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 884

show ntp associations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1467

show ntp counters associations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1471

show ntp counters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1469

show ntp status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1473

show ping-poll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1698

show platform classifier statistics utilization brief . . . . . . . . . . . . . . . . . . . . . . . . . 385

show platform classifier statistics utilization brief . . . . . . . . . . . . . . . . . . . . . . . . . 893

show platform port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386

show platform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384

show policy-map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 894

show port etherchannel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 537

show port-security interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391

show port-security intrusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392

show power-inline counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 560

show power-inline interface detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 564

show power-inline interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 562

show power-inline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 557

show privilege. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149

show process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210

show provisioning (stack) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1224

show proxy-autoconfig-file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1049

show radius statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1120

show radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1117

show reboot history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213

show rmon alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1588

show rmon event. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1589

show rmon history. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1591

show rmon statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1593

show router-id. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214

show running-config atmf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1429

show running-config interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

613-50137-01 Rev A Command Reference for FS980M Series 51

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

show running-config log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311

show running-config snmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1482

show running-config ssh. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1616

show running-config stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1223

show running-config trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1654

show running-config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

show security-password configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150

show security-password user. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151

show snmp-server community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1484

show snmp-server group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1485

show snmp-server user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1486

show snmp-server view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1487

show snmp-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1483

show spanning-tree brief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461

show spanning-tree mst config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 463

show spanning-tree mst detail interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 466

show spanning-tree mst detail interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471

show spanning-tree mst detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464

show spanning-tree mst instance interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 469

show spanning-tree mst instance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 468

show spanning-tree mst interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470

show spanning-tree mst . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 462

show spanning-tree statistics instance interface . . . . . . . . . . . . . . . . . . . . . . . . . . 476

show spanning-tree statistics instance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475

show spanning-tree statistics interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 478

show spanning-tree statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473

show spanning-tree vlan range-index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480

show spanning-tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458

show ssh client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1620

show ssh server allow-users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1623

show ssh server deny-users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1624

show ssh server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1621

show ssh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1618

show stack detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1227

show stack resiliencylink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1231

613-50137-01 Rev A Command Reference for FS980M Series 52

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

show stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1225

show startup-config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116

show static-channel-group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 538

show storm-control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393

show system environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216

show system interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217

show system mac. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218

show system pluggable detail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230

show system pluggable diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233

show system pluggable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228

show system serialnumber. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219

show system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215

show tacacs+. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1155

show tech-support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220

show telnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152

show test cable-diagnostics tdr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235

show trigger. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1655

show users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153

show version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

show vlan classifier group interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410

show vlan classifier group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409

show vlan classifier interface group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411

show vlan classifier rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412

show vlan private-vlan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413

show vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408

shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330

snmp trap link-status suppress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1490

snmp trap link-status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1488

snmp-server community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1494

snmp-server contact. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1495

snmp-server enable trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1496

snmp-server engineID local reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1500

snmp-server engineID local . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1498

snmp-server group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1501

snmp-server host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1503

613-50137-01 Rev A Command Reference for FS980M Series 53

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

snmp-server legacy-ifadminstatus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1505

snmp-server location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1506

snmp-server source-interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1507

snmp-server startup-trap-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1508

snmp-server user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1509

snmp-server view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1512

snmp-server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1492

source-ip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1702

spanning-tree autoedge (RSTP and MSTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 481

spanning-tree bpdu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 482

spanning-tree cisco-interoperability (MSTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 484

spanning-tree edgeport (RSTP and MSTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485

spanning-tree enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 486

spanning-tree errdisable-timeout enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 488

spanning-tree errdisable-timeout interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 489

spanning-tree force-version. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490

spanning-tree forward-time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 491

spanning-tree guard root . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 492

spanning-tree hello-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 493

spanning-tree link-type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 494

spanning-tree max-age . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495

spanning-tree max-hops (MSTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 496

spanning-tree mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 497

spanning-tree mst configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 498

spanning-tree mst instance path-cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

spanning-tree mst instance priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 502

spanning-tree mst instance restricted-role. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503

spanning-tree mst instance restricted-tcn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 505

spanning-tree mst instance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499

spanning-tree path-cost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 506

spanning-tree portfast (STP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507

spanning-tree portfast bpdu-filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509

spanning-tree portfast bpdu-guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511

spanning-tree priority (bridge priority) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513

spanning-tree priority (port priority). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514

613-50137-01 Rev A Command Reference for FS980M Series 54

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

spanning-tree restricted-role. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515

spanning-tree restricted-tcn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516

spanning-tree transmit-holdcount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 517

speed (asyn). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222

speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394

ssh client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1627

ssh server allow-users. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1631

ssh server authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1633

ssh server deny-users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1635

ssh server max-auth-tries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1637

ssh server resolve-host. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1638

ssh server scp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1639

ssh server sftp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1640

ssh server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1629

ssh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1625

stack disabled-master-monitoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1233

stack enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1234

stack management subnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1236

stack management vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1237

stack priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1238

stack renumber cascade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1240

stack renumber. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1239

stack resiliencylink. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1242

stack software-auto-synchronize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1244

stack virtual-chassis-id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1245

stack virtual-mac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1246

static-channel-group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 539

storm-action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 895

storm-control level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .396

storm-downtime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 896

storm-protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 897

storm-rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 898

storm-window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 899

subject-name (trustpoint configuration). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1146

switch provision (stack) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1247

613-50137-01 Rev A Command Reference for FS980M Series 55

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

switchport access vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414

switchport atmf-agentlink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1430

switchport atmf-arealink remote-area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1431

switchport atmf-crosslink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1433

switchport atmf-guestlink. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1435

switchport atmf-link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1437

switchport enable vlan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415

switchport mode access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416

switchport mode private-vlan trunk promiscuous. . . . . . . . . . . . . . . . . . . . . . . . . 418

switchport mode private-vlan trunk secondary . . . . . . . . . . . . . . . . . . . . . . . . . . . 420

switchport mode private-vlan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417

switchport mode trunk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 422

switchport port-security aging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398

switchport port-security maximum. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399

switchport port-security violation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400

switchport port-security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397

switchport private-vlan host-association . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423

switchport private-vlan mapping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424

switchport resiliencylink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1249

switchport trunk allowed vlan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425

switchport trunk native vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 428

switchport voice dscp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429

switchport voice vlan priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 432

switchport voice vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430

tacacs-server host . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1157

tacacs-server key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1159

tacacs-server timeout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1160

tcpdump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 604

telnet server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155

telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154

terminal length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156

terminal monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224

terminal resize. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157

test cable-diagnostics tdr interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236

test interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339

613-50137-01 Rev A Command Reference for FS980M Series 56

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1660

thrash-limiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401

time (trigger) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1661

timeout (ping polling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1704

timers (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 695

traceroute ipv6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 632

traceroute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 605

trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1663

trigger activate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1665

trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1664

trust dscp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 900

type atmf node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1438

type atmf node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1666

type cpu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1669

type interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1670

type memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1671

type periodic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1672

type ping-poll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1673

type reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1674

type stack disabled-master. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1675

type stack link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1676

type stack master-fail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1677

type stack member . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1678

type time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1679

type usb. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1680

undebug aaa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1098

undebug all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225

undebug atmf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1441

undebug dot1x. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 941

undebug epsr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1277

undebug igmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 730

undebug ip packet interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 606

undebug lacp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541

undebug loopprot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 402

undebug mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1581

613-50137-01 Rev A Command Reference for FS980M Series 57

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

undebug mstp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518

undebug ping-poll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1706

undebug platform packet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403

undebug radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1121

undebug rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 696

undebug snmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1513

undebug ssh client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1641

undebug ssh server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1642

undebug stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1252

undebug trigger. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1681

up-count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1705

username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1442

username . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158

version (RIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 697

vlan classifier activate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434

vlan classifier group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435

vlan classifier rule ipv4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436

vlan classifier rule proto. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437

vlan database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440

vlan mode stack-local-vlan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1250

vlan mode stack-local-vlan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 441

vlan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433

vty access-class (numbered) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 841

vty ipv6 access-class (named) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 849

wait . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315

write file. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118

write memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

write terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

wrr-queue disable queues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 901

wrr-queue egress-rate-limit queues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 902

wrr-queue weight queues. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 903

613-50137-01 Rev A Command Reference for FS980M Series 58

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Part 1: Setup and Troubleshooting

613-50137-01 Rev A Command Reference for FS980M Series 59

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

CLI Navigation

Commands

Introduction

Overview This chapter provides an alphabetical reference for the commands used to

navigate between different modes. This chapter also provides a reference for the

help and show commands used to help navigate within the CLI.

Command List •“configure terminal” on page 60

•“disable (Privileged Exec mode)” on page 61

•“do” on page 62

•“enable (Privileged Exec mode)” on page 63

•“end” on page 65

•“exit” on page 66

•“help” on page 67

•“logout” on page 68

•“show history” on page 69

613-50137-01 Rev A Command Reference for FS980M Series 60

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

CLI NAVIGATION COMMANDS

CONFIGURE TERMINAL

configure terminal

Overview This command enters the Global Configuration command mode.

Syntax configure terminal

Mode Privileged Exec

Example To enter the Global Configuration command mode (note the change in the

command prompt), enter the command:

awplus# configure terminal

awplus(config)#

613-50137-01 Rev A Command Reference for FS980M Series 61

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

CLI NAVIGATION COMMANDS

DISABLE (PRIVILEGED EXEC MODE)

disable (Privileged Exec mode)

Overview This command exits the Privileged Exec mode, returning the prompt to the User

Exec mode. To end a session, use the exit command.

Syntax disable

Mode Privileged Exec

Example To exit the Privileged Exec mode, enter the command:

awplus# disable

awplus>

Commands

enable (Privileged Exec mode)

end

exit

613-50137-01 Rev A Command Reference for FS980M Series 62

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

CLI NAVIGATION COMMANDS

Overview This command lets you to run User Exec and Privileged Exec mode commands

when you are in any configuration mode.

Syntax do <command>

Mode Any configuration mode

Example awplus# configure terminal

awplus(config)# do ping 192.0.2.23

Parameter Description

<command>Specify the command and its parameters.

613-50137-01 Rev A Command Reference for FS980M Series 63

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

CLI NAVIGATION COMMANDS

ENABLE (PRIVILEGED EXEC MODE)

enable (Privileged Exec mode)

Overview This command enters the Privileged Exec mode and optionally changes the

privilege level for a session. If a privilege level is not specified then the maximum

privilege level (15) is applied to the session. If the optional privilege level is omitted

then only users with the maximum privilege level can access Privileged Exec mode

without providing the password as specified by the enable password or enable

secret commands. If no password is specified then only users with the maximum

privilege level set with the username command can assess Privileged Exec mode.

Syntax enable [<privilege-level>]

Mode User Exec

Usage Many commands are available from the Privileged Exec mode that configure

operating parameters for the device, so you should apply password protection to

the Privileged Exec mode to prevent unauthorized use. Passwords can be

encrypted but then cannot be recovered. Note that non-encrypted passwords are

shown in plain text in configurations.

The username command sets the privilege level for the user. After login, users are

given access to privilege level 1. Users access higher privilege levels with the

enable (Privileged Exec mode) command. If the privilege level specified is higher

than the users configured privilege level specified by the username command,

then the user is prompted for the password for that level.

Note that a separate password can be configured for each privilege level using the

enable password and the enable secret commands from the Global Configuration

mode. The service password-encryption command encrypts passwords

configured by the enable password and the enable secret commands, so

passwords are not shown in plain text in configurations.

Example The following example shows the use of the enable command to enter the

Privileged Exec mode (note the change in the command prompt).

awplus> enable

awplus#

The following example shows the enable command enabling access the

Privileged Exec mode for users with a privilege level of 7 or greater. Users with a

privilege level of 7 or greater do not need to enter a password to access Privileged

Exec mode. Users with a privilege level 6 or less need to enter a password to access

Parameter Description

<privilege

- level>

Specify the privilege level for a CLI session in the range <1-15>, where

15 is the maximum privilege level, 7 is the intermediate privilege level

and 1 is the minimum privilege level. The privilege level for a user must

match or exceed the privilege level set for the CLI session for the user

to access Privileged Exec mode. Privilege level for a user is configured

by username.

613-50137-01 Rev A Command Reference for FS980M Series 64

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

CLI NAVIGATION COMMANDS

ENABLE (PRIVILEGED EXEC MODE)

Privilege Exec mode. Use the enable password command or the enable secret

commands to set the password to enable access to Privileged Exec mode.

awplus> enable 7

awplus#

Commands

disable (Privileged Exec mode)

enable password

enable secret

exit

service password-encryption

username

613-50137-01 Rev A Command Reference for FS980M Series 65

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

CLI NAVIGATION COMMANDS

END

end

Overview This command returns the prompt to the Privileged Exec command mode from

any other advanced command mode.

Syntax end

Mode All advanced command modes, including Global Configuration and Interface

Configuration modes.

Example The following example shows the use of the end command to return to the

Privileged Exec mode directly from Interface mode.

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# end

awplus#

Commands

disable (Privileged Exec mode)

enable (Privileged Exec mode)

exit

613-50137-01 Rev A Command Reference for FS980M Series 66

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

CLI NAVIGATION COMMANDS

EXIT

exit

Overview This command exits the current mode, and returns the prompt to the mode at the

previous level. When used in User Exec mode, the exit command terminates the

session.

Syntax exit

Mode All command modes, including Global Configuration and Interface Configuration

modes.

Example The following example shows the use of the exit command to exit Interface mode,

and return to Configure mode.

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# exit

awplus(config)#

Commands

disable (Privileged Exec mode)

enable (Privileged Exec mode)

end

613-50137-01 Rev A Command Reference for FS980M Series 67

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

CLI NAVIGATION COMMANDS

HELP

help

Overview This command displays a description of the AlliedWare Plus™ OS help system.

Syntax help

Mode All command modes

Example To display a description on how to use the system help, use the command:

awplus# help

Output Figure 1-1: Example output from the help command

When you need help at the command line, press '?'.



If nothing matches, the help list will be empty. Delete 

characters until entering a '?' shows the available options.



Enter '?' after a complete parameter to show remaining valid 

command parameters (e.g. 'show ?').



Enter '?' after part of a parameter to show parameters that 

complete the typed letters (e.g. 'show ip?').

613-50137-01 Rev A Command Reference for FS980M Series 68

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

CLI NAVIGATION COMMANDS

LOGOUT

logout

Overview This command exits the User Exec or Privileged Exec modes and ends the session.

Syntax logout

Mode User Exec and Privileged Exec

Example To exit the User Exec mode, use the command:

awplus# logout

613-50137-01 Rev A Command Reference for FS980M Series 69

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

CLI NAVIGATION COMMANDS

SHOW HISTORY

show history

Overview This command lists the commands entered in the current session. The history

buffer is cleared automatically upon reboot.

The output lists all command line entries, including commands that returned an

error.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show history

Mode User Exec and Privileged Exec

Example To display the commands entered during the current session, use the command:

awplus# show history

Output Figure 1-2: Example output from the show history command

1 en

2 show ru

3 conf t

4 route-map er deny 3

5 exit

6 ex

7 di

613-50137-01 Rev A Command Reference for FS980M Series 70

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

File and

Configuration

Management

Commands

Introduction

This chapter provides an alphabetical reference of AlliedWare Plus™ OS file and

configuration management commands.

Filename Syntax

and Keyword

Usage

Many of the commands in this chapter use the placeholder “filename” to represent

the name and location of the file that you want to act on. The following table

explains the syntax of the filename for each different type of file location.

When you copy a

file... Use this syntax: Example:

Copying in local

Flash memory

flash:[/][<directory>/]<filename>To specify a file in the configs directory

in Flash:

flash:configs/example.cfg

Copying to or from

a USB storage

device

usb:[/][<directory>/]<filename>To specify a file in the top-level

directory of the USB stick:

usb:example.cfg

Copying with

HTTP

http://[[<username>:<password>]@]

{<hostname>|<host-ip>}[/<filepath

>]/<filename>

To specify a file in the configs directory

on the server:

http://www.company.com/configs/exa

mple.cfg

Copying with TFTP tftp://[[<location>]/<directory>]

/<filename>

To specify a file in the top-level

directory of the server:

tftp://172.1.1.1/example.cfg

Copying with SCP scp://<username>@<location>[/<dir

ectory>][/<filename>]

To specify a file in the configs directory

on the server, logging on as user “bob”:

e.g.

scp://bob@10.10.0.12/configs/example

.cfg

613-50137-01 Rev A Command Reference for FS980M Series 71

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

Valid characters The filename and path can include characters from up to four categories. The

categories are:

1) uppercase letters: A to Z

2) lowercase letters: a to z

3) digits: 0 to 9

4) special symbols: most printable ASCII characters not included in the previous

three categories, including the following characters:

•-

•/

•.

•_

•@

•"

•'

•*

•:

•~

•?

Do not use spaces, parentheses or the + symbol within filenames. Use hyphens or

underscores instead.

Syntax for

directory listings

A leading slash (/) indicates the root of the current filesystem location.

In commands where you need to specify the local filesystem’s Flash base directory,

you may use flash or flash: or flash:/. For example, these commands are all the

same:

•dir flash

•dir flash:

•dir flash:/

Copying with SFTP sftp://[[<location>]/<directory>]

/<filename>

To specify a file in the top-level

directory of the server:

sftp://10.0.0.5/example.cfg

Copying to or from

stack member

Flash

<hostname>-<stack_ID>/flash:[/][<

directory>/]

<stack_member_filename>

To specify a file in the configs directory

on member 2 of a stack named vcstack:

vcstack-2/flash:/configs/example.cfg

When you copy a

file... Use this syntax: Example:

613-50137-01 Rev A Command Reference for FS980M Series 72

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

Similarly, you can specify the USB storage device base directory with usb or usb:

or usb:/

You cannot name a directory or subdirectory flash, nvs, usb, card, tftp, scp, sftp

or http. These keywords are reserved for tab completion when using various file

commands.

In a stacked environment you can only access flash and nvs using the stack

member filepath (e.g. dir awplus-2/flash:/). To access a USB storage

device on a backup stack member, use the remote-login command.

Command List •“autoboot enable” on page 74

•“boot config-file” on page 75

•“boot config-file backup” on page 77

•“boot system” on page 78

•“boot system backup” on page 80

•“cd” on page 81

•“copy (filename)” on page 82

•“copy current-software” on page 84

•“copy debug” on page 85

•“copy running-config” on page 86

•“copy startup-config” on page 87

•“copy zmodem” on page 88

•“create autoboot” on page 89

•“delete” on page 90

•“delete debug” on page 91

•“dir” on page 92

•“edit” on page 94

•“edit (filename)” on page 95

•“erase startup-config” on page 96

•“ip tftp source-interface” on page 97

•“

ipv6 tftp source-interface” on page 98

•“mkdir” on page 99

•“move” on page 100

•“move debug” on page 101

•“pwd” on page 102

•“rmdir” on page 103

•“show autoboot” on page 104

•“show boot” on page 105

613-50137-01 Rev A Command Reference for FS980M Series 73

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

•“show file” on page 107

•“show file systems” on page 108

•“show running-config” on page 110

•“show running-config interface” on page 114

•“show startup-config” on page 116

•“show version” on page 117

•“write file” on page 118

•“write memory” on page 119

•“write terminal” on page 120

613-50137-01 Rev A Command Reference for FS980M Series 74

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

AUTOBOOT ENABLE

autoboot enable

Overview This command enables the device to restore a release file and/or a configuration

file from external media, such as a USB storage device.

When the Autoboot feature is enabled, the device looks for a special file called

autoboot.txt on the external media. If this file exists, the device will check the

key and values in the file and recover the device with a new release file and/or

configuration file from the external media. An example of a valid autoboot.txt

file is shown in the following figure.

Figure 2-1: Example autoboot.txt file

Use the no variant of this command to disable the Autoboot feature.

NOTE: This command is not supported in a stacked configuration.

Syntax autoboot enable

no autoboot enable

Default The Autoboot feature operates the first time the device is powered up in the field,

after which the feature is disabled by default.

Mode Global Configuration

Example To enable the Autoboot feature, use the command:

awplus# configure terminal

awplus(config)# no autoboot enable

Commands

create autoboot

show autoboot

show boot

[AlliedWare Plus]

Copy_from_external_media_enabled=yes

Boot_Release=FS980-5.4.6-1.4.rel

Boot_Config=network1.cfg

613-50137-01 Rev A Command Reference for FS980M Series 75

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

BOOT CONFIG-FILE

boot config-file

Overview Use this command to set the configuration file to use during the next boot cycle.

Use the no variant of this command to remove the configuration file.

Syntax boot config-file <filepath-filename>

no boot config-file

Mode Global Configuration

Usage You can only specify that the configuration file is on a USB storage device if there

is a backup configuration file already specified in Flash. If you attempt to set the

configuration file on a USB storage device and a backup configuration file is not

specified in Flash, the following error message is displayed:

For an explanation of the configuration fallback order, see the File Management

Feature Overview and Configuration Guide.

Examples To run the configuration file “branch.cfg” stored on the device’s Flash filesystem

the next time the device boots up, use the commands:

awplus# configure terminal

awplus(config)# boot config-file flash:/branch.cfg

To stop running the configuration file “branch.cfg” stored on the device’s Flash

filesystem when the device boots up, use the commands:

awplus# configure terminal

awplus(config)# no boot config-file flash:/branch.cfg

To run the configuration file “branch.cfg” stored on the switch’s USB storage

device filesystem the next time the device boots up, use the commands:

awplus# configure terminal

awplus(config)# boot config-file usb:/branch.cfg

Parameter Description

<filepath-filename> Filepath and name of a configuration file.

The specified configuration file must exist in the

specified filesystem.

Valid configuration files must have a . cfg extension.

% Backup configuration files must be stored in the flash 

filesystem

613-50137-01 Rev A Command Reference for FS980M Series 76

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

BOOT CONFIG-FILE

To stop running the configuration file “branch.cfg” stored on the switch’s USB

storage device filesystem when the device boots up, use the commands:

awplus# configure terminal

awplus(config)# no boot config-file usb:/branch.cfg

Commands

boot config-file backup

boot system

boot system backup

show boot

613-50137-01 Rev A Command Reference for FS980M Series 77

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

BOOT CONFIG-FILE BACKUP

boot config-file backup

Overview Use this command to set a backup configuration file to use if the main

configuration file cannot be accessed.

Use the no variant of this command to remove the backup configuration file.

Syntax boot config-file backup <filepath-filename>

no boot config-file backup

Mode Global Configuration

Usage For an explanation of the configuration fallback order, see the File Management

Feature Overview and Configuration Guide.

Examples To set the configuration file backup.cfg as the backup to the main

configuration file, use the commands:

awplus# configure terminal

awplus(config)# boot config-file backup flash:/backup.cfg

To remove the configuration file backup.cfg as the backup to the main

configuration file, use the commands:

awplus# configure terminal

awplus(config)# no boot config-file backup flash:/backup.cfg

Commands

boot config-file

boot system

boot system backup

show boot

Parameter Description

<filepath-filename> Filepath and name of a backup configuration file.

Backup configuration files must be in the Flash filesystem.

Valid backup configuration files must have a . cfg

extension.

backup The specified file is a backup configuration file.

613-50137-01 Rev A Command Reference for FS980M Series 78

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

BOOT SYSTEM

boot system

Overview Use this command to set the release file to load during the next boot cycle.

Use the no variant of this command to remove the release file as the boot file.

Syntax boot system <filepath-filename>

no boot system

Mode Global Configuration

Usage You can only specify that the release file is on a USB storage device if there is a

backup release file already specified in Flash. If you attempt to set the release file

on a USB storage device and a backup release file is not specified in Flash, the

following error message is displayed:

In a VCStack configuration, the stack only accepts a release file on a USB storage

device if a USB storage device is inserted in all stack members and all stack

members have a bootloader version that supports booting from it. If a stack

member has a USB storage device removed an error message is displayed. For

example, if stack member 2 does not have a USB storage device inserted the

following message is displayed:

Examples To run the release file FS980-5.4.6-1.4.rel stored on the device’s Flash filesystem the

next time the device boots up, use the commands:

awplus# configure terminal

awplus(config)# boot system flash:/FS980-5.4.6-1.4.rel

To remove the release file FS980-5.4.6-1.4.rel stored on the device’s Flash

filesystem the next time the device boots up, use the commands:

awplus# configure terminal

awplus(config)# no boot system flash:/FS980-5.4.6-1.4.rel

Parameter Description

<filepath-filename> Filepath and name of a release file.

The specified release file must exist and must be stored

in the root directory of the specified filesystem.

Valid release files must have a . rel extension.

% A backup boot image must be set before setting a current boot 

image on USB storage device

% Stack member 2 has no USB storage device inserted

613-50137-01 Rev A Command Reference for FS980M Series 79

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

BOOT SYSTEM

To run the release file FS980-5.4.6-1.4.rel stored on the switch’s USB storage device

filesystem the next time the device boots up, use the commands:

awplus# configure terminal

awplus(config)# boot system usb:/FS980-5.4.6-1.4.rel

To remove the release file FS980-5.4.6-1.4.rel stored on the switch’s USB storage

device filesystem the next time the device boots up, use the commands:

awplus# configure terminal

awplus(config)# boot system usb:/FS980-5.4.6-1.4.rel

In a VCStack configuration, if there is not enough space to synchronize the new

release across the stack, the boot system command has an interactive mode that

prompts you to delete old releases.

awplus# configure terminal

awplus(config)# boot system FS980-5.4.6-1.4.rel

Answering “y” at the prompt will cause the system to delete the specified file:

awplus(config)# y

Commands

boot config-file

boot config-file backup

boot system backup

show boot

Insufficient flash available on stack member-2 (11370496)

to synchronize file FS980-5.4.6-1.4.rel 

(14821895).



List of release files on stack member-2

FS980-5.4.6-1.1.rel (14822400)



Select files to free up space,

Delete awplus-2/flash:/FS980-5.4.6-1.1.rel? (y/n)[n]:y

Deleting selected files, please wait............................

Successful operation

VCS synchronizing file across the stack, please wait.............

File synchronization with stack member-2 successfully completed

[DONE]

613-50137-01 Rev A Command Reference for FS980M Series 80

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

BOOT SYSTEM BACKUP

boot system backup

Overview Use this command to set a backup release file to load if the main release file cannot

be loaded.

Use the no variant of this command to remove the backup release file as the

backup boot file.

Syntax boot system backup <filepath-filename>

no boot system backup

Mode Global Configuration

Examples To specify the file FS980-5.4.6-1.1.rel as the backup to the main release file, use the

commands:

awplus# configure terminal

awplus(config)# boot system backup flash:/FS980-5.4.6-1.1.rel

To remove the file FS980-5.4.6-1.1.rel as the backup to the main release file, use the

commands:

awplus# configure terminal

awplus(config)# no boot system backup

flash:/FS980-5.4.6-1.1.rel

Commands

boot config-file

boot config-file backup

boot system

show boot

Parameter Description

<filepath-filename> Filepath and name of a backup release file.

Backup release files must be in the Flash filesystem.

Valid release files must have a . rel extension.

backup The specified file is a backup release file.

613-50137-01 Rev A Command Reference for FS980M Series 81

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

Overview This command changes the current working directory.

Syntax cd <directory-name>

Mode Privileged Exec

Example To change to the directory called images, use the command:

awplus# cd images

Commands

dir

pwd

show file systems

Parameter Description

<directory-name> Name and path of the directory.

613-50137-01 Rev A Command Reference for FS980M Series 82

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

COPY (FILENAME)

copy (filename)

Overview This command copies a file. This allows you to:

• copy files from your device to a remote device

• copy files from a remote device to your device

• copy files stored on Flash memory to or from a different memory type, such

as a USB storage device

• create two copies of the same file on your device

Syntax copy <source-name> <destination-name>

Mode Privileged Exec

Examples To use TFTP to copy the file bob.key into the current directory from the remote

server at 10.0.0.1, use the command:

awplus# copy tftp://10.0.0.1/bob.key bob.key

To use SFTP to copy the file new.cfg into the current directory from a remote server

at 10.0.1.2, use the command:

awplus# copy sftp://10.0.1.2/new.cfg bob.key

To use SCP with the username “beth” to copy the file old.cfg into the directory

config_files on a remote server that is listening on TCP port 2000, use the

command:

awplus# copy scp://beth@serv:2000/config_files/old.cfg old.cfg

To copy the file newconfig.cfg onto your device’s Flash from a USB storage device,

use the command:

awplus# copy usb:/newconfig.cfg flash:/newconfig.cfg

To copy the file newconfig.cfg to a USB storage device from your device’s Flash, use

the command:

awplus# copy flash:/newconfig.cfg usb:/newconfig.cfg

To copy the file config.cfg into the current directory from a USB storage device, and

rename it to configtest.cfg, use the command:

awplus# copy usb:/config.cfg configtest.cfg

Parameter Description

<source-name> The filename and path of the source file. See Introduction

on page 70 for valid syntax.

<destination-name> The filename and path for the destination file. See

Introduction on page 70 for valid syntax.

613-50137-01 Rev A Command Reference for FS980M Series 83

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

COPY (FILENAME)

To copy the file config.cfg into the current directory from a remote file server, and

rename it to configtest.cfg, use the command:

awplus# copy fserver:/config.cfg configtest.cfg

To copy the file test.txt from the top level of Flash on stack member 2 to the current

directory in the stack master, use the command:

awplus# copy awplus-2/flash:/test.txt test.txt

Note that you must specify either the NVS or Flash filesystem on the (backup) stack

member (flash: in this example).

Commands

copy zmodem

edit (filename)

show file systems

613-50137-01 Rev A Command Reference for FS980M Series 84

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

COPY CURRENT-SOFTWARE

copy current-software

Overview This command copies the AlliedWare Plus™ OS software that the device has

booted from, to a destination file. Specify whether the destination is Flash or USB

when saving the software to the local filesystem.

Syntax copy current-software <destination-name>

Mode Privileged Exec

Example To copy the current software as installed in the working directory with the file

name my-release.rel, use the command:

awplus# copy current-software my-release.rel

Commands

boot system backup

show boot

Parameter Description

<destination-name> The filename and path where you would like the current

running-release saved. This command creates a file if no file

exists with the specified filename. If a file already exists,

then the CLI prompts you before overwriting the file. See

Introduction on page 70 for valid syntax.

613-50137-01 Rev A Command Reference for FS980M Series 85

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

COPY DEBUG

copy debug

Overview This command copies a specified debug file to a destination file. Specify whether

the destination is Flash or USB when saving the software to the local filesystem.

Syntax copy debug {<destination-name>|debug|flash|nvs|scp|tftp|usb}

{<source-name>|debug|flash|nvs|scp|tftp|usb}

Mode Privileged Exec

Example To copy debug output to a USB storage device with a filename “my-debug”, use

the following command:

awplus# copy debug usb:my-debug

Output Figure 2-2: CLI prompt after entering the copy debug command

Commands

delete debug

move debug

Parameter Description

<destination-name> The filename and path where you would like the debug

output saved. See Introduction on page 70 for valid syntax.

<source-name> The filename and path where the debug output originates.

See Introduction on page 70 for valid syntax.

Enter source file name []:

613-50137-01 Rev A Command Reference for FS980M Series 86

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

COPY RUNNING-CONFIG

copy running-config

Overview This command copies the running-config to a destination file, or copies a source

file into the running-config. Commands entered in the running-config do not

survive a device reboot unless they are saved in a configuration file.

Syntax copy <source-name> running-config

copy running-config [<destination-name>]

copy running-config startup-config

Mode Privileged Exec

Examples To copy the running-config into the startup-config, use the command:

awplus# copy running-config startup-config

To copy the file layer3.cfg into the running-config, use the command:

awplus# copy layer3.cfg running-config

To use SCP to copy the running-config as current.cfg to the remote server

listening on TCP port 2000, use the command:

awplus# copy running-config

scp://user@server:2000/config_files/current.cfg

Commands

copy startup-config

write file

write memory

Parameter Description

<source-name>The filename and path of a configuration file. This must be

a valid configuration file with a . cfg filename extension.

Specify this when you want the script in the file to become

the new running-config. See Introduction on page 70 for

valid syntax.

<destination-name>The filename and path where you would like the current

running-config saved. This command creates a file if no file

exists with the specified filename. If a file already exists,

then the CLI prompts you before overwriting the file. See

Introduction on page 70 for valid syntax. If you do not

specify a file name, the device saves the running-config to

a file called default.cfg.

startup-config Copies the running-config into the file set as the current

startup-config file.

613-50137-01 Rev A Command Reference for FS980M Series 87

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

COPY STARTUP-CONFIG

copy startup-config

Overview This command copies the startup-config script into a destination file, or

alternatively copies a configuration script from a source file into the startup-config

file.

Syntax copy <source-name> startup-config

copy startup-config <destination-name>

Mode Privileged Exec

Examples To copy the file Layer3.cfg to the startup-config, use the command:

awplus# copy Layer3.cfg startup-config

To copy the startup-config as the file oldconfig.cfg in the current

directory, use the command:

awplus# copy startup-config oldconfig.cfg

Commands

copy running-config

Parameter Description

<source-name> The filename and path of a configuration file. This must be

a valid configuration file with a . cfg filename extension.

Specify this to copy the script in the file into the startup-

config file. Note that this does not make the copied file the

new startup file, so any further changes made in the

configuration file are not added to the startup-config file

unless you reuse this command. See Introduction on page

70 for valid syntax.

<destination-name> The destination and filename that you are saving the

startup- config as. This command creates a file if no file

exists with the specified filename. If a file already exists,

then the CLI prompts you before overwriting the file. See

Introduction on page 70 for valid syntax.

613-50137-01 Rev A Command Reference for FS980M Series 88

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

COPY ZMODEM

copy zmodem

Overview This command allows you to copy files using ZMODEM using Minicom. ZMODEM

works over a serial connection and does not need any interfaces configured to do

a file transfer.

Syntax copy <source-name> zmodem

copy zmodem

Mode Privileged Exec

Example To copy the local file asuka.key using ZMODEM, use the command:

awplus# copy asuka.key zmodem

Commands

copy (filename)

show file systems

Parameter Description

<source-name> The filename and path of the source file. See Introduction on

page 70 for valid syntax.

613-50137-01 Rev A Command Reference for FS980M Series 89

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

CREATE AUTOBOOT

create autoboot

Overview Use this command to create an autoboot.txt file on external media. This

command will automatically ensure that the keys and values that are expected in

this file are correct. After the file is created the create autoboot command will

copy the current release and configuration files across to the external media. The

external media is then available to restore a release file and/or a configuration file

to the device.

Syntax create autoboot usb

Mode Privileged Exec

Example To create an autoboot.txt file on a USB storage device, use the command:

awplus# create autoboot usb

Commands

autoboot enable

show autoboot

show boot

613-50137-01 Rev A Command Reference for FS980M Series 90

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

DELETE

delete

Overview This command deletes files or directories.

Syntax delete [force] [recursive] <filename>

Mode Privileged Exec

Examples To delete the file temp.cfg from the current directory, use the command:

awplus# delete temp.cfg

To delete the read-only file one.cfg from the current directory, use the

command:

awplus# delete force one.cfg

To delete the directory old_configs, which is not empty, use the command:

awplus# delete recursive old_configs

To delete the directory new_configs, which is not empty, without prompting if

any read-only files are being deleted, use the command:

awplus# delete force recursive new_configs

Commands

erase startup-config

rmdir

Parameter Description

force Ignore nonexistent filenames and never prompt before deletion.

recursive Remove the contents of directories recursively.

<filename>The filename and path of the file to delete. See Introduction on page

70 for valid syntax.

613-50137-01 Rev A Command Reference for FS980M Series 91

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

DELETE DEBUG

delete debug

Overview Use this command to delete a specified debug output file.

Syntax delete debug <source-name>

Mode Privileged Exec

Example To delete debug output, use the following command:

awplus# delete debug

Output Figure 2-3: CLI prompt after entering the delete debug command

Commands

copy debug

move debug

Parameter Description

<source-name> The filename and path where the debug output originates.

See Introduction on page 70 for valid URL syntax.

Enter source file name []:

613-50137-01 Rev A Command Reference for FS980M Series 92

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

DIR

dir

Overview This command lists the files on a filesystem. If no directory or file is specified then

this command lists the files in the current working directory.

Syntax dir [all] [recursive] [sort [reverse] [name|size|time]]

[<filename>|debug|flash|nvs|usb]

Mode Privileged Exec

Usage In a stacked environment you can use the CLI on a stack master to access

filesystems that are located on another stack member. The syntax is:

<hostname>-<stack_ID>/flash:[/][<directory>/]

<stack_member_filename>

For example, to specify a file in the “configs” directory on member 2 of a stack,

enter:

awplus-2/flash:/configs/example.cfg

Examples To list the files in the current working directory, use the command:

awplus# dir

To list the non-hidden files in the root of the Flash filesystem, use the command:

awplus# dir flash

Parameter Description

all List all files.

recursive List the contents of directories recursively.

sort Sort directory listing.

reverse Sort using reverse order.

name Sort by name.

size Sort by size.

time Sort by modification time (default).

<filename>The name of the directory or file. If no directory or file is

specified, then this command lists the files in the current

working directory.

debug Debug root directory

flash Flash memory root directory

nvs NVS memory root directory

usb USB storage device root directory

613-50137-01 Rev A Command Reference for FS980M Series 93

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

DIR

To list all the files in the root of the Flash filesystem, use the command:

awplus# dir all flash:

To list recursively the files in the Flash filesystem, use the command:

awplus# dir recursive flash:

To list the files in alphabetical order, use the command:

awplus# dir sort name

To list the files by size, smallest to largest, use the command:

awplus# dir sort reverse size

To sort the files by modification time, oldest to newest, use the command:

awplus# dir sort reverse time

To list the files within the Flash filesystem for stack member 2, use the command:

awplus# dir awplus-2/flash:/

Note that you must specify the filesystem on the stack member (flash in this

example).

Output Figure 2-4: Example output from the dir command

Commands

pwd

awplus#dir

630 -rw- May 19 2016 23:36:31 example.cfg

23652123 -rw- May 17 2016 03:41:18 FS980-5.4.6-1.4.rel 

149 -rw- Feb 9 2016 00:40:35 exception.log

613-50137-01 Rev A Command Reference for FS980M Series 94

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

EDIT

edit

Overview This command opens a text file in the AlliedWare Plus™ text editor. Once opened

you can use the editor to alter to the file.

If a filename is specified and it already exists, then the editor opens it in the text

editor.

If no filename is specified, the editor prompts you for one when you exit it.

Before starting the editor make sure your terminal, terminal emulation program, or

Telnet client is 100% compatible with a VT100 terminal. The editor uses VT100

control sequences to display text on the terminal.

For more information about using the editor, including control sequences, see the

File Management Feature Overview and Configuration Guide.

Syntax edit [<filename>]

Mode Privileged Exec

Examples To create and edit a new text file, use the command:

awplus# edit

To edit the existing configuration file myconfig.cfg stored on your device’s

Flash memory, use the command:

awplus# edit myconfig.cfg

Commands

edit (filename)

show file

Parameter Description

<filename> Name of a file in the local Flash filesystem.

613-50137-01 Rev A Command Reference for FS980M Series 95

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

EDIT (FILENAME)

edit (filename)

Overview This command opens a remote text file as read-only in the AlliedWare Plus™ text

editor.

Before starting the editor make sure your terminal, terminal emulation program, or

Telnet client is 100% compatible with a VT100 terminal. The editor uses VT100

control sequences to display text on the terminal.

Syntax edit <filename>

Mode Privileged Exec

Example To view the file bob.key stored in the security directory of a TFTP server, use the

command:

awplus# edit tftp://security/bob.key

Commands

copy (filename)

edit

show file

Parameter Description

<filename> The filename and path of the remote file. See Introduction on

page 70 for valid syntax.

613-50137-01 Rev A Command Reference for FS980M Series 96

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

ERASE STARTUP-CONFIG

erase startup-config

Overview This command deletes the file that is set as the startup-config file, which is the

configuration file that the system runs when it boots up.

At the next restart, the device loads the default configuration file, default.cfg. If

default.cfg no longer exists, then the device loads with the factory default

configuration. This provides a mechanism for you to return the device to the

factory default settings.

Syntax erase startup-config

Mode Privileged Exec

Example To delete the file currently set as the startup-config, use the command:

awplus# erase startup-config

Commands

boot config-file backup

copy running-config

copy startup-config

show boot

613-50137-01 Rev A Command Reference for FS980M Series 97

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

IP TFTP SOURCE-INTERFACE

ip tftp source-interface

Overview Use this command to manually specify the IP address that all TFTP requests

originate from. This is useful in network configurations where TFTP servers only

accept requests from certain devices, or where the server cannot dynamically

determine the source of the request.

Use the no variant of this command to stop specifying a source.

Syntax ip tftp source-interface [<interface>|<ip-add>]

no ip tftp source-interface

Default There is no default source specified.

Mode Global Configuration

Usage This command is helpful in network configurations where TFTP traffic needs to

traverse point-to-point links or subnets within your network, and you do not want

to propagate those point-to-point links through your routing tables.

In those circumstances, the TFTP server cannot dynamically determine the source

of the TFTP request, and therefore cannot send the requested data to the correct

device. Specifying a source interface or address enables the TFTP server to send the

data correctly.

Example To specify that TFTP requests originate from the IP address 192.0.2.1, use the

following commands:

awplus# configure terminal

awplus(config)# ip tftp source-interface 192.0.2.1

Commands

copy (filename)

Parameter Description

<interface> The VLAN that TFTP requests originate from. The device will use

the IP address of this interface as its source IP address.

<ip-add> The IP address that TFTP requests originate from, in dotted

decimal format

613-50137-01 Rev A Command Reference for FS980M Series 98

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

IPV6 TFTP SOURCE-INTERFACE

ipv6 tftp source-interface

Overview Use this command to manually specify the IPv6 address that all TFTP requests

originate from. This is useful in network configurations where TFTP servers only

accept requests from certain devices, or where the server cannot dynamically

determine the source of the request.

Use the no variant of this command to stop specifying a source.

Syntax ipv6 tftp source-interface [<interface>|<ipv6-add>]

no ipv6 tftp source-interface

Default There is no default source specified.

Mode Global Configuration

Usage This command is helpful in network configurations where TFTP traffic needs to

traverse point-to-point links or subnets within your network, and you do not want

to propagate those point-to-point links through your routing tables.

In those circumstances, the TFTP server cannot dynamically determine the source

of the TFTP request, and therefore cannot send the requested data to the correct

device. Specifying a source interface or address enables the TFTP server to send the

data correctly.

Example To specify that TFTP requests originate from the IPv6 address 2001:db8::8a2e:7334,

use the following commands:

awplus# configure terminal

awplus(config)# ipv6 tftp source-interface 2001:db8::8a2e:7334

Commands

copy (filename)

Parameter Description

<interface> The VLAN that TFTP requests originate from. The device will use

the IPv6 address of this interface as its source IPv6 address.

<ipv6-add> The IPv6 address that TFTP requests originate from, in the format

x:x::x:x, for example, 2001:db8::8a2e:7334.

613-50137-01 Rev A Command Reference for FS980M Series 99

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

MKDIR

mkdir

Overview This command makes a new directory.

Syntax mkdir <name>

Mode Privileged Exec

Usage You cannot name a directory or subdirectory flash, nvs, usb, card, tftp, scp, sftp

or http. These keywords are reserved for tab completion when using various file

commands.

Example To make a new directory called images in the current directory, use the

command:

awplus# mkdir images

Commands

dir

pwd

Parameter Description

<name> The name and path of the directory that you are creating.

613-50137-01 Rev A Command Reference for FS980M Series 100

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

MOVE

move

Overview This command renames or moves a file.

Syntax move <source-name> <destination-name>

Mode Privileged Exec

Examples To rename the file temp.cfg to startup.cfg, use the command:

awplus# move temp.cfg startup.cfg

To move the file temp.cfg from the root of the Flash filesystem to the directory

myconfigs, use the command:

awplus# move temp.cfg myconfigs/temp.cfg

Commands

delete

edit

show file

show file systems

Parameter Description

<source-name> The filename and path of the source file. See Introduction

on page 70 for valid syntax.

<destination-name> The filename and path of the destination file. See

Introduction on page 70 for valid syntax.

613-50137-01 Rev A Command Reference for FS980M Series 101

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

MOVE DEBUG

move debug

Overview This command moves a specified debug file to a destination debug file.

Syntax move debug {<destination-name>|debug|flash|nvs|usb}

Mode Privileged Exec

Example To move debug output onto a USB storage device with a filename “my-debug”, use

the following command:

awplus# move debug usb:my-debug

Output Figure 2-5: CLI prompt after entering the move debug command

Commands

copy debug

delete debug

Parameter Description

<destination-name> The filename and path where you would like the debug

output moved to. See Introduction on page 70 for valid

syntax.

Enter source file name []:

613-50137-01 Rev A Command Reference for FS980M Series 102

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

PWD

pwd

Overview This command prints the current working directory.

Syntax pwd

Mode Privileged Exec

Example To print the current working directory, use the command:

awplus# pwd

Commands

613-50137-01 Rev A Command Reference for FS980M Series 103

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

RMDIR

rmdir

Overview This command removes a directory. This command only works on empty

directories, unless you specify the optional force keyword.

Syntax rmdir [force] <name>

Mode Privileged Exec

Usage In a stacked environment you can use the CLI on a stack master to access

filesystems that are located on another stack member. See the Introduction on

page 70 for syntax details.

Examples To remove the directory “images” from the top level of the Flash filesystem, use the

command:

awplus# rmdir flash:/images

To create a directory called “level1” containing a subdirectory called “level2”, and

then force the removal of both directories, use the commands:

awplus# mkdir level1

awplus# mkdir level1/level2

awplus# rmdir force level1

To remove a directory called “test” from the top level of the Flash filesystem on

stack member 3, use the command:

awplus# rmdir awplus-3/flash:/test

Note that you must specify the filesystem (flash: in this example).

Commands

dir

mkdir

pwd

Parameter Description

force Optional keyword that allows you to delete directories that

are not empty and contain files or subdirectories.

<name>The name and path of the directory.

613-50137-01 Rev A Command Reference for FS980M Series 104

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

SHOW AUTOBOOT

show autoboot

Overview This command displays the Autoboot configuration and status.

Syntax show autoboot

Mode Privileged Exec

Example To show the Autoboot configuration and status, use the command:

awplus# show autoboot

Output Figure 2-6: Example output from the show autoboot command

Figure 2-7: Example output from the show autoboot command when an

external media source is not present

Commands

autoboot enable

create autoboot

show boot

awplus#show autoboot

Autoboot configuration

--------------------------------------------------------------------------------

Autoboot status : enabled

USB file autoboot.txt exists : yes



Restore information on USB

Autoboot enable in autoboot.txt : yes

Restore release file : FS980-5.4.6-1.4.rel 

(file exists)

Restore configuration file : network_1.cfg (file exists)

awplus#show autoboot

Autoboot configuration

--------------------------------------------------------------------------------

Autoboot status : disabled 

External media source : media not found.

613-50137-01 Rev A Command Reference for FS980M Series 105

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

SHOW BOOT

show boot

Overview This command displays the current boot configuration. We recommend that the

currently running release is set as the current boot image.

Syntax show boot

Mode Privileged Exec

Example To show the current boot configuration, use the command:

awplus# show boot

Output Figure 2-8: Example output from the show boot command when the current

boot config is on a USB storage device



awplus#show boot

Boot configuration

----------------------------------------------------------------

Current software : FS980-5.4.6-1.4.rel

Current boot image : usb:/FS980-5.4.6-1.4.rel

Backup boot image : flash:/FS980-5.4.6-1.1.rel

Default boot config: flash:/default.cfg

Current boot config: usb:/my.cfg (file exists)

Backup boot config: flash:/backup.cfg (file not found)

Autoboot status : enabled

Table 1: Parameters in the output of the show boot command

Parameter Description

Current software The current software release that the device is using.

Current boot image The boot image currently configured for use during the

next boot cycle.

Backup boot image The boot image to use during the next boot cycle if the

device cannot load the main image.

Default boot

config

The default startup configuration file. The device loads

this configuration script if no file is set as the startup-

config file.

Current boot

config

The configuration file currently configured as the

startup-config file. The device loads this configuration file

during the next boot cycle if this file exists.

613-50137-01 Rev A Command Reference for FS980M Series 106

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

SHOW BOOT

Commands

autoboot enable

boot config-file backup

boot system backup

show autoboot

Backup boot config The configuration file to use during the next boot cycle if

the main configuration file cannot be loaded.

Autoboot status The status of the Autoboot feature; either enabled or

disabled.

Table 1: Parameters in the output of the show boot command (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 107

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

SHOW FILE

show file

Overview This command displays the contents of a specified file.

Syntax show file <filename>

Mode Privileged Exec

Example To display the contents of the file oldconfig.cfg, which is in the current

directory, use the command:

awplus# show file oldconfig.cfg

Commands

edit

edit (filename)

show file systems

Parameter Description

<filename> Name of a file on the local Flash filesystem, or name and

directory path of a file.

613-50137-01 Rev A Command Reference for FS980M Series 108

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

SHOW FILE SYSTEMS

show file systems

Overview This command lists the filesystems and their utilization information where

appropriate.

Syntax show file systems

Mode Privileged Exec

Examples To display the filesystems, use the command:

awplus# show file systems

Output Figure 2-9: Example output from the show file systems command

awplus#show file systems

Size(b) Free(b) Type Flags Prefixes S/D/V Lcl/Ntwk Avail

-------------------------------------------------------------------

63.0M 28.5M flash rw flash: static local Y

- - system rw system: virtual local -

10.0M 9.8M debug rw debug: static local Y

499.0K 431.0K nvs rw nvs: static local Y

- - tftp rw tftp: - network -

- - scp rw scp: - network -

- - sftp ro sftp: - network -

- - http ro http: - network -

- - rsync rw rsync: - network -

Table 2: Parameters in the output of the show file systems command

Parameter Description

Size (B)

Available

The total memory available to this filesystem. The units are given

after the value and are M for Megabytes or k for kilobytes.

Free (B) The total memory free within this filesystem. The units are given

after the value and are M for Megabytes or k for kilobytes.

Type The memory type used for this filesystem; one of:

flash

system

nvs

tftp

scp

sftp

http.

Flags The file setting options: rw (read write), ro (read only).

613-50137-01 Rev A Command Reference for FS980M Series 109

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

SHOW FILE SYSTEMS

Commands

edit

edit (filename)

show file

Prefixes The prefixes used when entering commands to access the

filesystems; one of:

flash

system

nvs

tftp

scp

sftp

http.

S/V/D The memory type: static, virtual, dynamic.

Lcl / Ntwk Whether the memory is located locally or via a network

connection.

Avail Whether the memory is accessible: Y (yes), N (no), - (not applicable)

Table 2: Parameters in the output of the show file systems command (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 110

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

SHOW RUNNING-CONFIG

show running-config

Overview This command displays the current configuration of your device. Its output

includes all non-default configuration. The default settings are not displayed.

NOTE: You can control the output by entering | or > at the end of the command:

• To display only lines that contain a particular word, enter:

| include <word>

• To start the display at the first line that contains a particular word, enter:

| begin <word>

• To save the output to a file, enter:

> <filename>

Syntax show running-config [full|<feature>]

Parameter Description

full Display the running-config for all features. This is the default setting, so

it is the same as entering show running-config.

<feature>Display only the configuration for a single feature. The features

available depend on your device and will be some of the following list:

access-list ACL configuration

antivirus Antivirus configuration

application Application configuration

as-path Autonomous system path filter

configuration

as-path access-list Configuration of ACLs for AS path filtering

atmf Allied Telesis Management Framework

configuration

bgp Border Gateway Protocol (BGP)

configuration

community-list Community-list configuration

crypto Security-specific configuration

dhcp DHCP configuration

dpi Deep Packet Inspection configuration

entity Entity configuration

firewall Firewall configuration

interface Interface configuration. See show

running-config interface for further

options.

613-50137-01 Rev A Command Reference for FS980M Series 111

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

SHOW RUNNING-CONFIG

ip Internet Protocol (IP) configuration

ip pim dense-mode PIM-DM configuration

ip pim sparse-mode PIM-SM configuration

ip route IP static route configuration

ip-reputation IP Reputation configuration

ips IPS configuration

ipsec Internet Protocol Security (IPSec)

configuration

ipv6 Internet Protocol version 6 (IPv6)

configuration

ipv6 access-list IPv6 ACL configuration

ipv6 mroute IPv6 multicast route configuration

ipv6 prefix-list IPv6 prefix list configuration

ipv6 route IPv6 static route configuration

isakmp Internet Security Association Key

Management Protocol (ISAKMP)

configuration

key chain Authentication key management

configuration

l2tp-profile L2TP tunnel profile configuration

lldp LLDP configuration

log Logging utility configuration

malware-protection Malware protection configuration

nat Network Address Translation configuration

power-inline Power over Ethernet (PoE) configuration

policy-based-routing Policy-based routing (PBR) configuration

pppoe-ac PPPoE access concentrator configuration

prefix-list Prefix-list configuration

route-map Route-map configuration

router Router configuration

router-id Configuration of the router identifier for

this system

security-password Strong password security configuration

snmp SNMP configuration

ssh Secure Shell configuration

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 112

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

SHOW RUNNING-CONFIG

Mode Privileged Exec and Global Configuration

Example To display the current configuration of your device, use the command:

awplus# show running-config

Output Figure 2-10: Example output from show running-config

switch Switch configuration

web-control Web Control configuration

Parameter Description

!

service password-encryption

!

no banner motd

!

username manager privilege 15 password 8 $1$bJoVec4D$JwOJGPr7YqoExA0GVasdE0

!

no service ssh

!

service telnet

!

service http

!

no clock timezone

!

snmp-server

!

aaa authentication enable default local

aaa authentication login default local

!

stack virtual-mac

stack virtual-chassis-id 3622

!

ip domain-lookup

!

no ip multicast-routing

!

spanning-tree mode rstp

!

lacp global-passive-mode enable

no spanning-tree rstp enable

interface port1.0.1-1.0.26

switchport

switchport mode access

!

line con 0

exec-timeout 0 0

length 0

line vty 0 4

!

end

613-50137-01 Rev A Command Reference for FS980M Series 113

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

SHOW RUNNING-CONFIG

Commands

copy running-config

show running-config interface

613-50137-01 Rev A Command Reference for FS980M Series 114

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

SHOW RUNNING-CONFIG INTERFACE

show running-config interface

Overview This command displays the current configuration of one or more interfaces on the

device.

Syntax show running-config interface [<interface-list>] [dot1x|ip

igmp|ip multicast|ip pim dense-mode|ip pim sparse-mode|ipv6

rip|lacp|mstp|ospf|rip|rstp|stp]

Mode Privileged Exec and Global Configuration

Default Displays information for all protocols on all interfaces

Examples To display the current running configuration of your device for ports 1 to 4, use the

command:

awplus# show running-config interface port1.0.1-port1.0.4

Parameter Description

<interface-list>The interfaces or ports to display information about. An

interface-list can be:

• a VLAN (e.g. vlan2), a LAN port (e.g. port1.0.4), a static

channel group (e.g. sa2) or a dynamic (LACP) channel

group (e.g. po2)

• a continuous range of VLANs, ports, static channel

groups or dynamic (LACP) channel groups, separated by

a hyphen (e.g. vlan2-8, or port1.0.1-1.0.4, or sa1-2, or

po1-2)

• a comma-separated list of the above (e.g.

vlan2,vlan20-30). Do not mix interface types in a list.

The specified interfaces must exist.

dot1x Displays running configuration for 802.1X port

authentication for the specified interfaces.

lacp Displays running configuration for LACP (Link Aggregation

Control Protocol) for the specified interfaces.

ip igmp Displays running configuration for IGMP (Internet Group

Management Protocol) for the specified interfaces.

ip multicast Displays running configuration for general multicast

settings for the specified interfaces.

mstp Displays running configuration for MSTP (Multiple

Spanning Tree Protocol) for the specified interfaces.

rstp Displays running configuration for RSTP (Rapid Spanning

Tree Protocol) for the specified interfaces.

stp Displays running configuration for STP (Spanning Tree

Protocol) for the specified interfaces.

613-50137-01 Rev A Command Reference for FS980M Series 115

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

SHOW RUNNING-CONFIG INTERFACE

To display the current running configuration of a device for VLAN 1, use the

command:

awplus# show running-config interface vlan1

To display the current running configuration of a device for VLANs 1 and 3-5, use

the command:

awplus# show running-config interface vlan1,vlan3-vlan5

Output Figure 2-11: Example output from a show running-config interface port1.0.2

command

Commands

copy running-config

show running-config

awplus#show running-config interface port1.0.2

!

interface port1.0.2

switchport

switchport mode access

613-50137-01 Rev A Command Reference for FS980M Series 116

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

SHOW STARTUP-CONFIG

show startup-config

Overview This command displays the contents of the start-up configuration file, which is the

file that the device runs on start-up.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show startup-config

Mode Privileged Exec

Example To display the contents of the current start-up configuration file, use the

command:

awplus# show startup-config

Output Figure 2-12: Example output from the show startup-config command

Commands

boot config-file backup

copy running-config

copy startup-config

erase startup-config

show boot

awplus#show startup-config

!

service password-encryption

!

no banner motd

!

username manager privilege 15 password 8 $1$bJoVec4D$JwOJGPr7YqoExA0GVasdE0

!

no service ssh

!

service telnet

!

service http

!

no clock timezone

.

line con 0

line vty 0 4

!

end

613-50137-01 Rev A Command Reference for FS980M Series 117

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

SHOW VERSION

show version

Overview This command displays the version number and copyright details of the current

AlliedWare Plus™ OS your device is running.

Syntax show version

Mode User Exec and Privileged Exec

Example To display the version details of your currently installed software, use the

command:

awplus# show version

Commands

boot system backup

show boot

613-50137-01 Rev A Command Reference for FS980M Series 118

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

WRITE FILE

write file

Overview This command copies the running-config into the file that is set as the current

startup-config file. This command is a synonym of the write memory and copy

running-config startup-config commands.

Syntax write [file]

Mode Privileged Exec

Example To write configuration data to the start-up configuration file, use the command:

awplus# write file

Commands

copy running-config

write memory

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 119

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

WRITE MEMORY

write memory

Overview This command copies the running-config into the file that is set as the current

startup-config file. This command is a synonym of the write file and copy

running-config startup-config commands.

Syntax write [memory]

Mode Privileged Exec

Example To write configuration data to the start-up configuration file, use the command:

awplus# write memory

Commands

copy running-config

write file

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 120

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

FILE AND CONFIGURATION MANAGEMENT COMMANDS

WRITE TERMINAL

write terminal

Overview This command displays the current configuration of the device. This command is a

synonym of the show running-config command.

Syntax write terminal

Mode Privileged Exec

Example To display the current configuration of your device, use the command:

awplus# write terminal

Commands

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 121

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

User Access

Commands

Introduction

Overview This chapter provides an alphabetical reference of commands used to configure

user access.

Command List •“clear line console” on page 123

•“clear line vty” on page 124

•“enable password” on page 125

•“enable secret” on page 128

•“exec-timeout” on page 131

•“flowcontrol hardware (asyn/console)” on page 133

•“length (asyn)” on page 135

•“line” on page 136

•“privilege level” on page 138

•“security-password history” on page 139

•“security-password forced-change” on page 140

•“security-password lifetime” on page 141

•“security-password minimum-categories” on page 142

•“security-password minimum-length” on page 143

•“security-password reject-expired-pwd” on page 144

•“security-password warning” on page 145

•“service advanced-vty” on page 146

•“service password-encryption” on page 147

•“service telnet” on page 148

•“show privilege” on page 149

613-50137-01 Rev A Command Reference for FS980M Series 122

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

•“show security-password configuration” on page 150

•“show security-password user” on page 151

•“show telnet” on page 152

•“show users” on page 153

•“telnet” on page 154

•“telnet server” on page 155

•“terminal length” on page 156

•“terminal resize” on page 157

•“username” on page 158

613-50137-01 Rev A Command Reference for FS980M Series 123

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

CLEAR LINE CONSOLE

clear line console

Overview This command resets a console line. If a terminal session exists on the line then the

terminal session is terminated. If console line settings have changed then the new

settings are applied.

Syntax clear line console 0

Mode Privileged Exec

Example To reset the console line (asyn), use the command:

awplus# clear line console 0

awplus# % The new settings for console line 0 have been applied

Commands

clear line vty

flowcontrol hardware (asyn/console)

line

show users

613-50137-01 Rev A Command Reference for FS980M Series 124

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

CLEAR LINE VTY

clear line vty

Overview This command resets a VTY line. If a session exists on the line then it is closed.

Syntax clear line vty <0-32>

Mode Privileged Exec

Example To reset the first VTY line, use the command:

awplus# clear line vty 1

Commands

privilege level

line

show telnet

show users

Parameter Description

<0-32>Line number

613-50137-01 Rev A Command Reference for FS980M Series 125

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

ENABLE PASSWORD

enable password

Overview To set a local password to control access to various privilege levels, use the enable

password Global Configuration command. Use the enable password command to

modify or create a password to be used, and use the no enable password

command to remove the password.

Note that the enable secret command is an alias for the enable password

command, and the no enable secret command is an alias for the no enable

password command. Issuing a no enable password command removes a password

configured with the enable secret command. The enable password command is

shown in the running and startup configurations. Note that if the enable secret

command is entered then enable password is shown in the configuration.

Syntax enable password [<plain>|8 <hidden>|level <1-15> 8 <hidden>]

no enable password [level <1-15>]

Default The privilege level for enable password is level 15 by default. Previously the default

was level 1.

Mode Global Configuration

Usage This command enables the Network Administrator to set a password for entering

the Privileged Exec mode when using the enable (Privileged Exec mode)

command. There are three methods to enable a password. In the examples below,

for each method, note that the configuration is different and the configuration file

output is different, but the password string to be used to enter the Privileged Exec

mode with the enable command is the same (mypasswd).

A user can now have an intermediate CLI security level set with this command for

privilege level 7 to access all the show commands in Privileged Exec mode and all

the commands in User Exec mode, but not any configuration commands in

Privileged Exec mode.

Parameter Description

<plain>Specifies the unencrypted password.

8Specifies a hidden password will follow.

<hidden>Specifies the hidden encrypted password. Use an encrypted

password for better security where a password crosses the network

or is stored on a TFTP server.

level Privilege level <1-15>. Level for which the password applies. You can

specify up to 16 privilege levels, using numbers 1 through 15. Level 1

is normal EXEC-mode user privileges for User Exec mode. If this

argument is not specified in the command or the no variant of the

command, the privilege level defaults to 15 (enable mode privileges)

for Privileged Exec mode. A privilege level of 7 can be set for

intermediate CLI security.

613-50137-01 Rev A Command Reference for FS980M Series 126

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

ENABLE PASSWORD

Note that the enable password command is an alias for the enable secret

command and one password per privilege level is allowed using these commands.

Do not assign one password to a privilege level with enable password and another

password to a privilege level with enable secret. Use enable password or enable

secret commands. Do not use both on the same level.

Using plain

passwords

The plain password is a clear text string that appears in the configuration file as

configured.

awplus# configure terminal

awplus(config)# enable password mypasswd

awplus(config)# end

This results in the following show output:

Using encrypted

passwords

You can configure an encrypted password using the service password-encryption

command. First, use the enable password command to specify the string that you

want to use as a password (mypasswd). Then, use the service

password-encryption command to encrypt the specified string (mypasswd). The

advantage of using an encrypted password is that the configuration file does not

show mypasswd, it will only show the encrypted string fU7zHzuutY2SA.

awplus# configure terminal

awplus(config)# enable password mypasswd

awplus(config)# service password-encryption

awplus(config)# end

This results in the following show output:

Using hidden

passwords

You can configure an encrypted password using the HIDDEN parameter (8) with

the enable password command. Use this method if you already know the

encrypted string corresponding to the plain text string that you want to use as a

password. It is not required to use the service password-encryption command for

awplus#show run

Current configuration:

hostname awplus

enable password mypasswd

!

interface lo

awplus#show run

Current configuration:

hostname awplus

enable password 8 fU7zHzuutY2SA

service password-encryption

!

interface lo

613-50137-01 Rev A Command Reference for FS980M Series 127

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

ENABLE PASSWORD

this method. The output in the configuration file will show only the encrypted

string, and not the text string.

awplus# configure terminal

awplus(config)# enable password 8 fU7zHzuutY2SA

awplus(config)# end

This results in the following show output:

Commands

enable (Privileged Exec mode)

enable secret

service password-encryption

privilege level

show privilege

username

show running-config

awplus#show run

Current configuration:

hostname awplus

enable password 8 fU7zHzuutY2SA

!

interface lo

613-50137-01 Rev A Command Reference for FS980M Series 128

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

ENABLE SECRET

enable secret

Overview To set a local password to control access to various privilege levels, use the enable

secret Global Configuration command. Use the enable secret command to modify

or create a password to be used, and use the no enable secret command to remove

the password.

Note that the enable secret command is an alias for the enable password

command, and the no enable secret command is an alias for the no enable

password command. Issuing a no enable password command removes a password

configured with the enable secret command. The enable password command is

shown in the running and startup configurations. Note that if the enable secret

command is entered then enable password is shown in the configuration

Syntax enable secret [<plain>|8 <hidden>|level <0-15> 8 <hidden>]

no enable secret [level <1-15>]

Default The privilege level for enable secret is level 15 by default.

Mode Global Configuration

Usage This command enables the Network Administrator to set a password for entering

the Privileged Exec mode when using the enable (Privileged Exec mode)

command. There are three methods to enable a password. In the examples below,

for each method, note that the configuration is different and the configuration file

output is different, but the password string to be used to enter the Privileged Exec

mode with the enable command is the same (mypasswd).

A user can have an intermediate CLI security level set with this command for

privilege level 7 to access all the show commands in Privileged Exec mode and all

the commands in User Exec mode, but not any configuration commands in

Privileged Exec mode.

Parameter Description

<plain>Specifies the unencrypted password.

8Specifies a hidden password will follow.

<hidden>Specifies the hidden encrypted password. Use an encrypted

password for better security where a password crosses the network

or is stored on a TFTP server.

level Privilege level <1-15>. Level for which the password applies. You can

specify up to 16 privilege levels, using numbers 1 through 15. Level 1

is normal EXEC-mode user privileges for User Exec mode. If this

argument is not specified in the command or the no variant of the

command, the privilege level defaults to 15 (enable mode privileges)

for Privileged Exec mode. A privilege level of 7 can be set for

intermediate CLI security.

613-50137-01 Rev A Command Reference for FS980M Series 129

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

ENABLE SECRET

Note that the enable secret command is an alias for the enable password

command and one password per privilege level is allowed using these commands.

Do not assign one password to a privilege level with enable password and another

password to a privilege level with enable secret. Use enable password or enable

secret commands. Do not use both on the same level.

Using plain

passwords

The plain password is a clear text string that appears in the configuration file as

configured.

awplus# configure terminal

awplus(config)# enable secret mypasswd

awplus(config)# end

This results in the following show output:

Using encrypted

passwords

Configure an encrypted password using the service password-encryption

command. First, use the enable password command to specify the string that you

want to use as a password (mypasswd). Then, use the service

password-encryption command to encrypt the specified string (mypasswd). The

advantage of using an encrypted password is that the configuration file does not

show mypasswd, it will only show the encrypted string fU7zHzuutY2SA.

awplus# configure terminal

awplus(config)# enable secret mypasswd

awplus(config)# service password-encryption

awplus(config)# end

This results in the following show output:

Using hidden

passwords

Configure an encrypted password using the HIDDEN parameter (8) with the

enable password command. Use this method if you already know the encrypted

string corresponding to the plain text string that you want to use as a password. It

is not required to use the service password-encryption command for this method.

awplus#show run

Current configuration:

hostname awplus

enable password mypasswd

!

interface lo

awplus#show run

Current configuration:

hostname awplus

enable password 8 fU7zHzuutY2SA

service password-encryption

!

interface lo

613-50137-01 Rev A Command Reference for FS980M Series 130

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

ENABLE SECRET

The output in the configuration file will show only the encrypted string, and not

the text string:

awplus# configure terminal

awplus(config)# enable secret 8 fU7zHzuutY2SA

awplus(config)# end

This results in the following show output:

Commands

enable (Privileged Exec mode)

enable secret

service password-encryption

privilege level

show privilege

username

show running-config

awplus#show run

Current configuration:

hostname awplus

enable password 8 fU7zHzuutY2SA

!

interface lo

613-50137-01 Rev A Command Reference for FS980M Series 131

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

EXEC-TIMEOUT

exec-timeout

Overview This command sets the interval your device waits for user input from either a

console or VTY connection. Once the timeout interval is reached, the connection is

dropped. This command sets the time limit when the console or VTY connection

automatically logs off after no activity.

The no variant of this command removes a specified timeout and resets to the

default timeout (10 minutes).

Syntax exec-timeout {<minutes>} [<seconds>]

no exec-timeout

Default The default for the exec-timeout command is 10 minutes and 0 seconds

(exec-timeout 10 0).

Mode Line Configuration

Usage This command is used set the time the telnet session waits for an idle VTY session,

before it times out. An exec-timeout 0 0 setting will cause the telnet session to

wait indefinitely. The command exec-timeout 0 0 is useful while configuring a

device, but reduces device security.

If no input is detected during the interval then the current connection resumes. If

no connections exist then the terminal returns to an idle state and disconnects

incoming sessions.

Examples To set VTY connections to timeout after 2 minutes, 30 seconds if there is no

response from the user, use the following commands:

awplus# configure terminal

awplus(config)# line vty 0 32

awplus(config-line)# exec-timeout 2 30

To reset the console connection to the default timeout of 10 minutes 0 seconds if

there is no response from the user, use the following commands:

awplus# configure terminal

awplus(config)# line console 0

awplus(config-line)# no exec-timeout

Validation

Commands

show running-config

Parameter Description

<minutes> <0-35791> Required integer timeout value in minutes

<seconds> <0-2147483> Optional integer timeout value in seconds

613-50137-01 Rev A Command Reference for FS980M Series 132

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

EXEC-TIMEOUT

Commands

line

service telnet

613-50137-01 Rev A Command Reference for FS980M Series 133

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

FLOWCONTROL HARDWARE (ASYN/CONSOLE)

flowcontrol hardware (asyn/console)

Overview Use this command to enable RTS/CTS (Ready To Send/Clear To Send) hardware

flow control on a terminal console line (asyn port) between the DTE (Data Terminal

Equipment) and the DCE (Data Communications Equipment).

Syntax flowcontrol hardware

no flowcontrol hardware

Mode Line Configuration

Default Hardware flow control is disabled by default.

Usage Hardware flow control makes use of the RTS and CTS control signals between the

DTE and DCE where the rate of transmitted data is faster than the rate of received

data. Flow control is a technique for ensuring that a transmitting entity does not

overwhelm a receiving entity with data. When the buffers on the receiving device

are full, a message is sent to the sending device to suspend the transmission until

the data in the buffers has been processed.

Hardware flow control can be configured on terminal console lines (e.g. asyn0). For

Reverse Telnet connections, hardware flow control must be configured to match

on both the Access Server and the Remote Device. For terminal console sessions,

hardware flow control must be configured to match on both the DTE and the DCE.

Settings are saved in the running configuration. Changes are applied after reboot,

clear line console, or after closing the session.

Use show running-config and show startup-config commands to view hardware

flow control settings that take effect after reboot for a terminal console line. See

the show running-config command output:

Note that line configuration commands do not take effect immediately. Line

configuration commands take effect after one of the following commands or

events:

•issuing a clear line console command

•issuing a reboot command

• logging out of the current session

awplus#show running-config

!

line con 1

speed 9600

mode out 2001

flowcontrol hardware

613-50137-01 Rev A Command Reference for FS980M Series 134

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

FLOWCONTROL HARDWARE (ASYN/CONSOLE)

Examples To enable hardware flow control on terminal console line asyn0, use the

commands:

awplus# configure terminal

awplus(config)# line console 0

awplus(config-line)# flowcontrol hardware

To disable hardware flow control on terminal console line asyn0, use the

commands:

awplus# configure terminal

awplus(config)# line console 0

awplus(config-line)# no flowcontrol hardware

Commands

clear line console

show running-config

speed (asyn)

613-50137-01 Rev A Command Reference for FS980M Series 135

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

LENGTH (ASYN)

length (asyn)

Overview Use this command to specify the number of rows of output that the device will

display before pausing, for the console or VTY line that you are configuring.

The no variant of this command restores the length of a line (terminal session)

attached to a console port or to a VTY to its default length of 22 rows.

Syntax length <0-512>

no length

Mode Line Configuration

Default The length of a terminal session is 22 rows. The no length command restores the

default.

Usage If the output from a command is longer than the length of the line the output will

be paused and the ‘–More–’ prompt allows you to move to the next screen full of

data.

A length of 0 will turn off pausing and data will be displayed to the console as long

as there is data to display.

Examples To set the terminal session length on the console to 10 rows, use the command:

awplus# configure terminal

awplus(config)# line console 0

awplus(config-line)# length 10

To reset the terminal session length on the console to the default (22 rows), use the

command:

awplus# configure terminal

awplus(config)# line console 0

awplus(config-line)# no length

To display output to the console continuously, use the command:

awplus# configure terminal

awplus(config)# line console 0

awplus(config-line)# length 0

Commands

terminal resize

terminal length

Parameter Description

<0-512> Number of lines on screen. Specify 0 for no pausing.

613-50137-01 Rev A Command Reference for FS980M Series 136

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

LINE

line

Overview Use this command to enter line configuration mode for the specified VTYs or the

console. The command prompt changes to show that the device is in Line

Configuration mode.

Syntax line vty <first-line> [<last-line>]

Mode Global Configuration

Usage In Line Configuration mode, you can configure console and virtual terminal

settings, including setting speed (asyn), length (asyn), privilege level, and

authentication (login authentication) or accounting (accounting login) method

lists.

To change the console (asyn) port speed, use this line command to enter Line

Configuration mode before using the speed (asyn) command. Set the console

speed (Baud rate) to match the transmission rate of the device connected to the

console (asyn) port on your device.

Note that line configuration commands do not take effect immediately. Line

configuration commands take effect after one of the following commands or

events:

•issuing a clear line console command

•issuing a reboot command

• logging out of the current session

Examples To enter Line Configuration mode in order to configure all VTYs, use the

commands:

awplus# configure terminal

awplus(config)# line vty 0 32

awplus(config-line)#

To enter Line Configuration mode to configure the console (asyn 0) port terminal

line, use the commands:

awplus# configure terminal

awplus(config)# line console 0

awplus(config-line)#

Parameter Description

<first-line> <0-32> Specify the first line number.

<last-line> <0-32> Specify the last line number.

console The console terminal line(s) for local access.

vty Virtual terminal for remote console access.

613-50137-01 Rev A Command Reference for FS980M Series 137

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

LINE

Commands

accounting login

clear line console

clear line vty

flowcontrol hardware (asyn/console)

length (asyn)

privilege level

speed (asyn)

613-50137-01 Rev A Command Reference for FS980M Series 138

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

PRIVILEGE LEVEL

privilege level

Overview This command sets a privilege level for VTY or console connections. The

configured privilege level from this command overrides a specific user’s initial

privilege level at the console login.

Syntax privilege level <1-15>

Mode Line Configuration

Usage You can set an intermediate CLI security level for a console user with this command

by applying privilege level 7 to access all show commands in Privileged Exec and

all User Exec commands. However, intermediate CLI security will not show

configuration commands in Privileged Exec.

Examples To set the console connection to have the maximum privilege level, use the

following commands:

awplus# configure terminal

awplus(config)# line console 0

awplus(config-line)# privilege level 15

To set all VTY connections to have the minimum privilege level, use the following

commands:

awplus# configure terminal

awplus(config)# line vty 0 5

awplus(config-line)# privilege level 1

To set all VTY connections to have an intermediate CLI security level, to access all

show commands, use the following commands:

awplus# configure terminal

awplus(config)# line vty 0 5

awplus(config-line)# privilege level 7

Commands

enable password

line

show privilege

username

613-50137-01 Rev A Command Reference for FS980M Series 139

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

SECURITY-PASSWORD HISTORY

security-password history

Overview This command specifies the number of previous passwords that are unable to be

reused. A new password is invalid if it matches a password retained in the

password history.

The no variant of the command disables this feature.

Syntax security-password history <0-15>

no security-password history

Default The default history value is 0, which will disable the history functionality.

Mode Global Configuration

Examples To restrict reuse of the three most recent passwords, use the command:

awplus# configure terminal

awplus(config)# security-password history 3

To allow the reuse of recent passwords, use the command:

awplus# configure terminal

awplus(config)# no security-password history

Commands

security-password forced-change

security-password lifetime

security-password minimum-categories

security-password minimum-length

security-password reject-expired-pwd

security-password warning

show running-config security-password

show security-password configuration

Parameter Description

<0-15> The allowable range of previous passwords to match against. A

value of 0 will disable the history functionality and is equivalent to

the no security-password history command. If the history

functionality is disabled, all users’ password history is reset and all

password history is lost.

613-50137-01 Rev A Command Reference for FS980M Series 140

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

SECURITY-PASSWORD FORCED-CHANGE

security-password forced-change

Overview This command specifies whether or not a user is forced to change an expired

password at the next login. If this feature is enabled, users whose passwords have

expired are forced to change to a password that must comply with the current

password security rules at the next login.

Note that to use this command, the lifetime feature must be enabled with the

security-password lifetime command and the reject-expired-pwd feature must be

disabled with the security-password reject-expired-pwd command.

The no variant of the command disables this feature.

Syntax security-password forced-change

no security-password forced-change

Default The forced-change feature is disabled by default.

Mode Global Configuration

Example To force a user to change their expired password at the next login, use the

command:

awplus# configure terminal

awplus(config)# security-password forced-change

Commands

security-password history

security-password lifetime

security-password minimum-categories

security-password minimum-length

security-password reject-expired-pwd

security-password warning

show running-config security-password

show security-password configuration

613-50137-01 Rev A Command Reference for FS980M Series 141

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

SECURITY-PASSWORD LIFETIME

security-password lifetime

Overview This command enables password expiry by specifying a password lifetime in days.

Note that when the password lifetime feature is disabled, it also disables the

security-password forced-change command and the security-password warning

command.

The no variant of the command disables this feature.

Syntax security-password lifetime <0-1000>

no security-password lifetime

Default The default password lifetime is 0, which will disable the lifetime functionality.

Mode Global Configuration

Example To configure the password lifetime to 10 days, use the command:

awplus# configure terminal

awplus(config)# security-password lifetime 10

Commands

security-password forced-change

security-password history

security-password minimum-categories

security-password minimum-length

security-password reject-expired-pwd

security-password warning

show running-config security-password

show security-password configuration

Parameter Description

<0-1000> Password lifetime specified in days. A value of 0 will disable lifetime

functionality and the password will never expire. This is equivalent

to the no security-password lifetime command.

613-50137-01 Rev A Command Reference for FS980M Series 142

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

SECURITY-PASSWORD MINIMUM-CATEGORIES

security-password minimum-categories

Overview This command specifies the minimum number of categories that the password

must contain in order to be considered valid. The password categories are:

• uppercase letters: A to Z

• lowercase letters: a to z

• digits: 0 to 9

• special symbols: all printable ASCII characters not included in the previous

three categories. The question mark (?) cannot be used as it is reserved for

help functionality.

Note that to ensure password security, the minimum number of categories should

align with the lifetime selected, i.e. the fewer categories specified the shorter the

lifetime specified.

Syntax security-password minimum-categories <1-4>

Default The default number of categories that the password must satisfy is 1.

Mode Global Configuration

Example To configure the required minimum number of character categories to be 3, use

the command:

awplus# configure terminal

awplus(config)# security-password minimum-categories 3

Commands

security-password forced-change

security-password history

security-password lifetime

security-password minimum-length

security-password reject-expired-pwd

security-password warning

show running-config security-password

show security-password configuration

username

Parameter Description

<1-4> Number of categories the password must satisfy, in the range 1 to 4.

613-50137-01 Rev A Command Reference for FS980M Series 143

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

SECURITY-PASSWORD MINIMUM-LENGTH

security-password minimum-length

Overview This command specifies the minimum allowable password length. This value is

checked against when there is a password change or a user account is created.

Syntax security-password minimum-length <1-23>

Default The default minimum password length is 1.

Mode Global Configuration

Example To configure the required minimum password length as 8, use the command:

awplus# configure terminal

awplus(config)# security-password minimum-length 8

Commands

security-password history

security-password forced-change

security-password lifetime

security-password minimum-categories

security-password reject-expired-pwd

security-password warning

show running-config security-password

show security-password configuration

username

Parameter Description

<1-23> Minimum password length in the range from 1 to 23.

613-50137-01 Rev A Command Reference for FS980M Series 144

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

SECURITY-PASSWORD REJECT-EXPIRED-PWD

security-password reject-expired-pwd

Overview This command specifies whether or not a user is allowed to login with an expired

password. Users with expired passwords are rejected at login if this functionality is

enabled. Users then have to contact the Network Administrator to change their

password.

CAUTION: Once all users’ passwords are expired you are unable to login to the device

again if the security-password reject-expired-pwd command has been executed. You

will have to reboot the device with a default configuration file, or load an earlier

software version that does not have the security password feature.

We recommend you never have the command line “security-password

reject-expired-pwd” in a default config file.

Note that when the reject-expired-pwd functionality is disabled and a user logs on

with an expired password, if the forced-change feature is enabled with

security-password forced-change command, a user may have to change the

password during login depending on the password lifetime specified by the

security-password lifetime command.

The no variant of the command disables this feature.

Syntax security-password reject-expired-pwd

no security-password reject-expired-pwd

Default The reject-expired-pwd feature is disabled by default.

Mode Global Configuration

Example To configure the system to reject users with an expired password, use the

command:

awplus# configure terminal

awplus(config)# security-password reject-expired-pwd

Commands

security-password forced-change

security-password history

security-password lifetime

security-password minimum-categories

security-password minimum-length

security-password warning

show running-config security-password

show security-password configuration

show security-password user

613-50137-01 Rev A Command Reference for FS980M Series 145

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

SECURITY-PASSWORD WARNING

security-password warning

Overview This command specifies the number of days before the password expires that the

user will receive a warning message specifying the remaining lifetime of the

password.

Note that the warning period cannot be set unless the lifetime feature is enabled

with the security-password lifetime command.

The no variant of the command disables this feature.

Syntax security-password warning <0-1000>

no security-password warning

Default The default warning period is 0, which disables warning functionality.

Mode Global Configuration

Example To configure a warning period of three days, use the command:

awplus# configure terminal

awplus(config)# security-password warning 3

Commands

security-password forced-change

security-password history

security-password lifetime

security-password minimum-categories

security-password minimum-length

security-password reject-expired-pwd

show running-config security-password

show security-password configuration

Parameter Description

<0-1000> Warning period in the range from 0 to 1000 days. A value 0 disables

the warning functionality and no warning message is displayed for

expiring passwords. This is equivalent to the no security-password

warning command. The warning period must be less than, or equal

to, the password lifetime set with the security-password lifetime

command.

613-50137-01 Rev A Command Reference for FS980M Series 146

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

SERVICE ADVANCED-VTY

service advanced-vty

Overview This command enables the advanced-vty help feature. This allows you to use TAB

completion for commands. Where multiple options are possible, the help feature

displays the possible options.

The no service advanced-vty command disables the advanced-vty help feature.

Syntax service advanced-vty

no service advanced-vty

Default The advanced-vty help feature is enabled by default.

Mode Global Configuration

Examples To disable the advanced-vty help feature, use the command:

awplus# configure terminal

awplus(config)# no service advanced-vty

To re-enable the advanced-vty help feature after it has been disabled, use the

following commands:

awplus# configure terminal

awplus(config)# service advanced-vty

613-50137-01 Rev A Command Reference for FS980M Series 147

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

SERVICE PASSWORD-ENCRYPTION

service password-encryption

Overview Use this command to enable password encryption. This is enabled by default.

When password encryption is enabled, the device displays passwords in the

running config in encrypted form instead of in plain text.

Use the no service password-encryption command to stop the device from

displaying newly-entered passwords in encrypted form. This does not change the

display of existing passwords.

Syntax service password-encryption

no service password-encryption

Mode Global Configuration

Example awplus# configure terminal

awplus(config)# service password-encryption

Validation

Commands

show running-config

Commands

enable password

613-50137-01 Rev A Command Reference for FS980M Series 148

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

SERVICE TELNET

service telnet

Overview Use this command to enable the telnet server. The server is enabled by default.

Enabling the telnet server starts the device listening for incoming telnet sessions

on the configured port.

The server listens on port 23, unless you have changed the port by using the

privilege level command.

Use the no variant of this command to disable the telnet server. Disabling the

telnet server will stop the device listening for new incoming telnet sessions.

However, existing telnet sessions will still be active.

Syntax service telnet [ip|ipv6]

no service telnet [ip|ipv6]

Default The IPv4 and IPv6 telnet servers are enabled by default.

The configured telnet port is TCP port 23 by default.

Mode Global Configuration

Examples To enable both the IPv4 and IPv6 telnet servers, use the following commands:

awplus# configure terminal

awplus(config)# service telnet

To enable the IPv6 telnet server only, use the following commands:

awplus# configure terminal

awplus(config)# service telnet ipv6

To disable both the IPv4 and IPv6 telnet servers, use the following commands:

awplus# configure terminal

awplus(config)# no service telnet

To disable the IPv6 telnet server only, use the following commands:

awplus# configure terminal

awplus(config)# no service telnet ipv6

Commands

clear line vty

show telnet

telnet server

613-50137-01 Rev A Command Reference for FS980M Series 149

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

SHOW PRIVILEGE

show privilege

Overview This command displays the current user privilege level, which can be any privilege

level in the range <1-15>. Privilege levels <1-6> allow limited user access (all User

Exec commands), privilege levels <7-14> allow restricted user access (all User Exec

commands plus Privileged Exec show commands). Privilege level 15 gives full user

access to all Privileged Exec commands.

Syntax show privilege

Mode User Exec and Privileged Exec

Usage A user can have an intermediate CLI security level set with this command for

privilege levels <7-14> to access all show commands in Privileged Exec mode and

all commands in User Exec mode, but no configuration commands in Privileged

Exec mode.

Example To show the current privilege level of the user, use the command:

awplus# show privilege

Output Figure 3-1: Example output from the show privilege command

Commands

privilege level

awplus#show privilege

Current privilege level is 15

awplus#disable

awplus>show privilege

Current privilege level is 1

613-50137-01 Rev A Command Reference for FS980M Series 150

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

SHOW SECURITY-PASSWORD CONFIGURATION

show security-password configuration

Overview This command displays the configuration settings for the various security

password rules.

Syntax show security-password configuration

Mode Privileged Exec

Example To display the current security-password rule configuration settings, use the

command:

awplus# show security-password configuration

Output Figure 3-2: Example output from the show security-password configuration

command

Commands

show running-config security-password

show security-password user

Security Password Configuration

Minimum password length ............................ 8

Minimum password character categories to match ..... 3

Number of previously used passwords to restrict..... 4

Password lifetime .................................. 30 day(s)

Warning period before password expires ........... 3 day(s)

Reject expired password at login ................... Disabled

Force changing expired password at login ......... Enabled

613-50137-01 Rev A Command Reference for FS980M Series 151

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

SHOW SECURITY-PASSWORD USER

show security-password user

Overview This command displays user account and password information for all users.

Syntax show security-password user

Mode Privileged Exec

Example To display the system users’ remaining lifetime or last password change, use the

command:

awplus# show security-password user

Output Figure 3-3: Example output from the show security-password user command

Commands

show running-config security-password

show security-password configuration

User account and password information



UserName Privilege Last-PWD-Change Remaining-lifetime

----------------------------------------------------------------

manager 15 4625 day(s) ago No Expiry

bob15 15 0 day(s) ago 30 days

ted7 7 0 day(s) ago No Expiry

mike1 1 0 day(s) ago No Expiry

613-50137-01 Rev A Command Reference for FS980M Series 152

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

SHOW TELNET

show telnet

Overview This command shows the Telnet server settings.

Syntax show telnet

Mode User Exec and Privileged Exec

Example To show the Telnet server settings, use the command:

awplus# show telnet

Output Figure 3-4: Example output from the show telnet command

Commands

clear line vty

service telnet

show users

telnet server

Telnet Server Configuration

------------------------------------------------------------

Telnet server : Enabled

Protocol : IPv4,IPv6

Port : 23

613-50137-01 Rev A Command Reference for FS980M Series 153

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

SHOW USERS

show users

Overview This command shows information about the users who are currently logged into

the device.

Syntax show users

Mode User Exec and Privileged Exec

Example To show the users currently connected to the device, use the command:

awplus# show users

Output Figure 3-5: Example output from the show users command

Line User Host(s) Idle Location Priv Idletime Timeout

con 0 manager idle 00:00:00 ttyS0 15 10 N/A

vty 0 bob idle 00:00:03 172.16.11.3 1 0 5

Table 1: Parameters in the output of the show users command

Parameter Description

Line Console port user is connected to.

User Login name of user.

Host(s) Status of the host the user is connected to.

Idle How long the host has been idle.

Location URL location of user.

Priv The privilege level in the range 1 to 15, with 15 being the highest.

Idletime The time interval the device waits for user input from either a

console or VTY connection.

Timeout The time interval before a server is considered unreachable.

613-50137-01 Rev A Command Reference for FS980M Series 154

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

TELNET

telnet

Overview Use this command to open a telnet session to a remote device.

Syntax telnet {<hostname>|[ip] <ipv4-addr>|[ipv6] <ipv6-addr>}

[<port>]

Mode User Exec and Privileged Exec

Examples To connect to TCP port 2602 on the device at 10.2.2.2, use the command:

awplus# telnet 10.2.2.2 2602

To connect to the telnet server host.example, use the command:

awplus# telnet host.example

To connect to the telnet server host.example on TCP port 100, use the

command:

awplus# telnet host.example 100

Parameter Description

<hostname>The host name of the remote system.

ip Keyword used to specify the IPv4 address or host name of a remote

system.

<ipv4-addr> An IPv4 address of the remote system.

ipv6 Keyword used to specify the IPv6 address of a remote system

<ipv6-addr> Placeholder for an IPv6 address in the format x:x::x:x, for

example, 2001:db8::8a2e:7334

<port>Specify a TCP port number (well known ports are in the range 1-

1023, registered ports are 1024-49151, and private ports are 49152-

65535).

613-50137-01 Rev A Command Reference for FS980M Series 155

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

TELNET SERVER

telnet server

Overview This command enables the telnet server on the specified TCP port. If the server is

already enabled then it will be restarted on the new port. Changing the port

number does not affect the port used by existing sessions.

Syntax telnet server {<1-65535>|default}

Mode Global Configuration

Example To enable the telnet server on TCP port 2323, use the following commands:

awplus# configure terminal

awplus(config)# telnet server 2323

Commands

show telnet

Parameter Description

<1-65535> The TCP port to listen on.

default Use the default TCP port number 23.

613-50137-01 Rev A Command Reference for FS980M Series 156

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

TERMINAL LENGTH

terminal length

Overview Use the terminal length command to specify the number of rows of output that

the device will display before pausing, for the currently-active terminal only.

Use the terminal no length command to remove the length specified by this

command. The default length will apply unless you have changed the length for

some or all lines by using the length (asyn) command.

Syntax terminal length <length>

terminal no length [<length>]

Mode User Exec and Privileged Exec

Examples The following example sets the number of lines to 15:

awplus# terminal length 15

The following example removes terminal length set previously:

awplus# terminal no length

Commands

terminal resize

length (asyn)

Parameter Description

<length><0-512> Number of rows that the device will display on the

currently-active terminal before pausing.

613-50137-01 Rev A Command Reference for FS980M Series 157

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

TERMINAL RESIZE

terminal resize

Overview Use this command to automatically adjust the number of rows of output on the

console, which the device will display before pausing, to the number of rows

configured on the user’s terminal.

Syntax terminal resize

Mode User Exec and Privileged Exec

Usage When the user’s terminal size is changed, then a remote session via SSH or TELNET

adjusts the terminal size automatically. However, this cannot normally be done

automatically for a serial or console port. This command automatically adjusts the

terminal size for a serial or console port.

Examples The following example automatically adjusts the number of rows shown on the

console:

awplus# terminal resize

Commands

length (asyn)

terminal length

613-50137-01 Rev A Command Reference for FS980M Series 158

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

USERNAME

username

Overview This command creates or modifies a user to assign a privilege level and a password.

NOTE: The default username privilege level of 1 is not shown in running-config output.

Any username privilege level that has been modified from the default is shown.

Syntax username <name> privilege <1-15> [password [8] <password>]

username <name> password [8] <password>

no username <name>

Mode Global Configuration

Default The privilege level is 1 by default. Note the default is not shown in running-config

output.

Parameter Description

<name>The login name for the user. Do not use punctuation marks such as single quotes (‘ ‘),

double quotes (“ “), or colons ( : ) with the user login name.

privilege The user’s privilege level. Use the privilege levels to set the access rights for each user.

<1-15> A privilege level: either 1-14 (limited access) or 15 (full access). A user

with privilege level 1-14 can only access higher privilege levels if an

enable password has been configured for the level the user tries to

access and the user enters that password.

A user at privilege level 1 can access the majority of show

commands. A user at privilege level 7 can access the majority of

show commands including platform show commands. Privilege

Level 15 (to access the Privileged Exec command mode) is required

to access configuration commands as well as show commands in

Privileged Exec.

password A password that the user must enter when logging in.

8Specifies that you are entering a password as a string that has

already been encrypted, instead of entering a plain-text password.

The running-config displays the new password as an encrypted

string even if password encryption is turned off.

Note that the user enters the plain-text version of the password

when logging in.

<password>The user’s password. The password can be up to 23 characters in

length and include characters from up to four categories. The

password categories are:

• uppercase letters: A to Z

• lowercase letters: a to z

• digits: 0 to 9

• special symbols: all printable ASCII characters not included in the

previous three categories. The question mark ? cannot be used as

it is reserved for help functionality.

613-50137-01 Rev A Command Reference for FS980M Series 159

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

USER ACCESS COMMANDS

USERNAME

Usage An intermediate CLI security level (privilege level 7 to privilege level 14) allows a

CLI user access to the majority of show commands, including the platform show

commands that are available at privilege level 1 to privilege level 6. Note that some

show commands, such as show running-configuration and show

startup-configuration, are only available at privilege level 15.

Examples To create the user “bob” with a privilege level of 15, for all show commands

including show running-configuration and show startup-configuration and to

access configuration commands in Privileged Exec command mode, and the

password “bobs_secret”, use the commands:

awplus# configure terminal

awplus(config)# username bob privilege 15 password bobs_secret

To create a user “junior_admin” with a privilege level of 7, which will have

intermediate CLI security level access for most show commands, and the password

“show_only”, use the commands:

awplus# configure terminal

awplus(config)# username junior_admin privilege 7 password

show_only

Commands

enable password

security-password minimum-categories

security-password minimum-length

613-50137-01 Rev A Command Reference for FS980M Series 160

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

GUI Commands

Introduction

Overview This chapter provides an alphabetical reference of commands used to configure

the GUI. For more information, see the Getting Started with Alliedware Plus

Command List •“atmf topology-gui enable” on page 161

•“gui-timeout” on page 162

•“log event-host” on page 164

•“service http” on page 165

•“show http” on page 166

613-50137-01 Rev A Command Reference for FS980M Series 161

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

GUI COMMANDS

ATMF TOPOLOGY-GUI ENABLE

atmf topology-gui enable

Overview Use this command to enable the operation of AMF Vista Manager on the Master

device.

Use the no variant of this command to disable this feature.

Syntax atmf topology-gui enable

no atmf topology-gui enable

Default By default the GUI support will not be enabled on AMF Master devices. An AMF

Controller device will have the GUI enabled by default. Regular nodes (not master

or controller) will always have it disabled.

Mode Global Configuration mode

Usage This command is run from an AMF Master node. Topology information about your

network is displayed in the GUI. For example; Node Name, status (i.e. link state,

node status and recovery status), Role (i.e. Master or Controller) and IP address.

Example To enable AMF Vista Manager on Node1, use the following commands:

Node1# configure terminal

Node1(config)# atmf topology-gui enable

To disable AMF Vista Manager on Node1, use the following commands:

Node1# configure terminal

Node1(config)# no atmf topology-gui enable

Commands

atmf enable

gui-timeout

log event-host

service http

613-50137-01 Rev A Command Reference for FS980M Series 162

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

GUI COMMANDS

GUI-TIMEOUT

gui-timeout

Overview Use this command to configure an idle timeout period for a GUI session. The time

can be set in minutes and/or seconds.

Use the no variant of this command to disable the GUI session idle timeout.

Syntax gui-timeout <minutes> [<seconds>]

no gui-timeout

Default Disabled

Mode Global Configuration

Usage The GUI uses the configured timeout period (set in either minutes and/or seconds)

to determine when a GUI session should be closed. Once the GUI timeout has

expired, you will need to login to reactivate your session.

To enter seconds only, enter 0 for minutes, followed by a space, and then enter the

seconds.

If the GUI timeout is disabled, a GUI session will remain active until you terminate

it. No idle time will be configured.

The same timeout period will apply to all GUI sessions logged into a specific

stand-alone device or stack.

Examples Use this command to configure the GUI timeout period for 3 minutes and 30

seconds for a GUI session.

awplus# gui-timeout 3 30

Use this command to configure the GUI timeout period for 0 minutes and 61

seconds for a GUI session.

awplus# gui-timeout 0 61

Use this command to disable the GUI timeout period.

awplus# no gui-timeout

Output Figure 4-1: Example output from gui-timeout

Parameter Description

<minutes> Specifies the idle time in minutes from 0 through 35791

<seconds> Specifies the idle time in seconds from 0 through 2147483

awplus#configure terminal

awplus(config)#gui-timeout 3 30

The new gui-timeout settings [3 min 30 sec] will apply to new sessions only

613-50137-01 Rev A Command Reference for FS980M Series 163

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

GUI COMMANDS

GUI-TIMEOUT

Commands

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 164

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

GUI COMMANDS

LOG EVENT-HOST

log event-host

Overview Use this command to set up an external host to log AMF topology events through

Vista Manager. This command is run on the Master device.

Use the no variant of this command to disable log events through Vista Manager.

Syntax log event-host [<ipv4-addr>|<ipv6-addr>] atmf-topology-event

no log event-host [<ipv4-addr>|<ipv6-addr>] atmf-topology-event

Default Log events are disabled by default.

Mode Global Configuration

Usage Event hosts are set so syslog sends the messages out as they come.

NOTE: There is a difference between log event and log host messages:

• Log event messages are sent out as they come by syslog

• Log host messages are set to wait for a number of messages (20) to send

them out together for traffic optimization.

Example To enable Node 1 to log event messages from host ipv6 address 192.0.2.31, use the

following commands:

Node1# configure terminal

Node1(config)# log event-host 192.0.2.31 atmf-topology-event

To disable Node 1 to log event messages from host ipv6 address 192.0.2.31, use the

following commands:

Node1# configure terminal

Node1(config)# no log event-host 192.0.2.31 atmf-topology-event

Commands

atmf topology-gui enable

Parameter Description

<ipv4-addr> ipv4 address of the event host

<ipv6-addr> ipv6 address of the event host

613-50137-01 Rev A Command Reference for FS980M Series 165

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

GUI COMMANDS

SERVICE HTTP

service http

Overview Use this command to enable the HTTP (Hypertext Transfer Protocol) service. This

service, which is enabled by default, is required to support the AlliedWare Plus™

GUI Java applet on a Java enabled browser.

Use the no variant of this command to disable the HTTP feature.

Syntax service http

no service http

Default Enabled

Mode Global Configuration

Validation

Commands

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 166

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

GUI COMMANDS

SHOW HTTP

show http

Overview This command shows the HTTP server settings.

Syntax show http

Mode User Exec and Privileged Exec

Example To show the HTTP server settings, use the command:

awplus# show http

Output Figure 4-2: Example output from the show http command

Commands

clear line vty

service http

awplus#show http

HTTP Server Configuration

------------------------------------------------------------

HTTP server : Enabled

Port : 80

613-50137-01 Rev A Command Reference for FS980M Series 167

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

System

Configuration and

Monitoring

Commands

Introduction

Overview This chapter provides an alphabetical reference of commands for configuring and

monitoring the system.

Command List •“banner exec” on page 169

•“banner login (system)” on page 171

•“banner motd” on page 173

•“clock set” on page 175

•“clock summer-time date” on page 176

•“clock summer-time recurring” on page 178

•“clock timezone” on page 180

•“ecofriendly led” on page 181

•“findme” on page 182

•“findme trigger” on page 184

•“hostname” on page 185

•“no debug all” on page 187

•“reboot” on page 188

•“reload” on page 189

•“show clock” on page 190

•“show cpu” on page 192

•“show cpu history” on page 195

•“show debugging” on page 198

•“show ecofriendly” on page 199

•“show interface memory” on page 200

613-50137-01 Rev A Command Reference for FS980M Series 168

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

•“show memory” on page 202

•“show memory allocations” on page 204

•“show memory history” on page 206

•“show memory pools” on page 208

•“show memory shared” on page 209

•“show process” on page 210

•“show reboot history” on page 213

•“show router-id” on page 214

•“show system” on page 215

•“show system environment” on page 216

•“show system interrupts” on page 217

•“show system mac” on page 218

•“show system serialnumber” on page 219

•“show tech-support” on page 220

•“speed (asyn)” on page 222

•“terminal monitor” on page 224

•“undebug all” on page 225

613-50137-01 Rev A Command Reference for FS980M Series 169

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

BANNER EXEC

banner exec

Overview This command configures the User Exec mode banner that is displayed on the

console after you login. The banner exec default command restores the User Exec

banner to the default banner. Use the no banner exec command to disable the

User Exec banner and remove the default User Exec banner.

Syntax banner exec <banner-text>

banner exec default

no banner exec

Default By default, the AlliedWare Plus™ version and build date is displayed at console

Mode Global Configuration

Examples To configure a User Exec mode banner after login (in this example, to tell people to

use the enable command to move to Privileged Exec mode), enter the following

commands:

To restore the default User Exec mode banner after login, enter the following

commands:

AlliedWare Plus (TM) 5.4.6-1 09/30/16 00:44:25

awplus#configure terminal



awplus(config)#banner exec Use enable to move to Priv Exec mode



awplus(config)#exit



awplus#exit

awplus login: manager



Password:



Use enable to move to Priv Exec mode



awplus>

613-50137-01 Rev A Command Reference for FS980M Series 170

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

BANNER EXEC

To remove the User Exec mode banner after login, enter the following commands:

Commands

banner login (system)

banner motd

awplus#configure terminal



awplus(config)#banner exec default



awplus(config)#exit



awplus#exit

awplus login: manager



Password:



AlliedWare Plus (TM) 5.4.6-1 09/30/16 13:03:59



awplus>

awplus#configure terminal



awplus(config)#no banner exec



awplus(config)#exit



awplus#exit



awplus login: manager



Password:



awplus>

613-50137-01 Rev A Command Reference for FS980M Series 171

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

BANNER LOGIN (SYSTEM)

banner login (system)

Overview This command configures the login banner that is displayed on the console when

you login. The login banner is displayed on all connected terminals. The login

banner is displayed after the MOTD (Message-of-the-Day) banner and before the

Use the no banner login command to disable the login banner.

Syntax banner login

no banner login

Default By default, no login banner is displayed at console login.

Mode Global Configuration

Examples To configure a login banner of “Authorised users only” to be displayed when you

To remove the login banner, enter the following commands:

awplus#configure terminal



awplus(config)#banner login



Type CNTL/D to finish.



Authorised users only



awplus(config)#exit



awplus#exit



authorised users only



awplus login: manager



Password:



AlliedWare Plus (TM) 5.4.6-1 09/30/16 13:03:59



awplus>

613-50137-01 Rev A Command Reference for FS980M Series 172

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

BANNER LOGIN (SYSTEM)

Commands

banner exec

banner motd

awplus#configure terminal



awplus(config)#no banner login



awplus(config)#exit



awplus#exit



awplus login: manager



Password:



AlliedWare Plus (TM) 5.4.6-1 09/30/16 13:03:59



awplus>

613-50137-01 Rev A Command Reference for FS980M Series 173

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

BANNER MOTD

banner motd

Overview Use this command to create or edit the text MotD (Message-of-the-Day) banner

displayed before login. The MotD banner is displayed on all connected terminals.

The MotD banner is useful for sending messages that affect all network users, for

example, any imminent system shutdowns.

Use the no variant of this command to delete the MotD banner.

Syntax banner motd <motd-text>

no banner motd

Default By default, the device displays the AlliedWare Plus™ OS version and build date

when you login.

Mode Global Configuration

Examples To configure a MotD banner of “System shutdown at 6pm today” to be displayed

when you log in, enter the following commands:

To delete the login banner, enter the following commands:

Parameter Description

<motd-text> The text to appear in the Message of the Day banner.

awplus>enable



awplus#configure terminal



awplus(config)#banner motd System shutdown at 6pm today



awplus(config)#exit



awplus#exit



System shutdown at 6pm today



awplus login: manager



Password:



AlliedWare Plus (TM) 5.4.6-1 09/30/16 13:03:59

613-50137-01 Rev A Command Reference for FS980M Series 174

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

BANNER MOTD

Commands

banner exec

banner login (system)

awplus>enable



awplus#configure terminal



awplus(config)#no banner motd



awplus(config)#exit



awplus#exit



awplus login: manager



Password:



AlliedWare Plus (TM) 5.4.6-1 09/30/16 13:03:59



awplus>

613-50137-01 Rev A Command Reference for FS980M Series 175

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

CLOCK SET

clock set

Overview This command sets the time and date for the system clock.

Syntax clock set <hh:mm:ss> <day> <month>



<year>

Mode Privileged Exec

Usage Configure the timezone before setting the local time. Otherwise, when you change

the timezone, the device applies the new offset to the local time.

NOTE: If Network Time Protocol (NTP) is enabled, then you cannot change the time or

date using this command. NTP maintains the clock automatically using an external

time source. If you wish to manually alter the time or date, you must first disable NTP.

Example To set the time and date on your system to 2pm on the 2nd of October 2016, use

the command:

awplus# clock set 14:00:00 2 oct 2016

Commands

clock timezone

Parameter Description

<hh:mm:ss> Local time in 24-hour format

<day> Day of the current month, from 1 to 31

<month> The first three letters of the current month

<year> Current year, from 2000 to 2035

613-50137-01 Rev A Command Reference for FS980M Series 176

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

CLOCK SUMMER-TIME DATE

clock summer-time date

Overview This command defines the start and end of summertime for a specific year only,

and specifies summertime’s offset value to Standard Time for that year.

The no variant of this command removes the device’s summertime setting. This

clears both specific summertime dates and recurring dates (set with the clock

summer-time recurring command).

By default, the device has no summertime definitions set.

Syntax clock summer-time <timezone-name> date <start-day>

<start-month> <start-year> <start-time> <end-day> <end-month>

<end-year> <end-time> <1-180>

no clock summer-time

Mode Global Configuration

Examples To set a summertime definition for New Zealand using NZST (UTC+12:00) as the

standard time, and NZDT (UTC+13:00) as summertime, with the summertime set to

begin on the 25th of September 2016 and end on the 2nd of April 2017:

awplus(config)# clock summer-time NZDT date 25 sep 2:00 2016 2

apr 2:00 2017 60

To remove any summertime settings on the system, use the command:

awplus(config)# no clock summer-time

Parameter Description

<timezone-name> A description of the summertime zone, up to 6 characters long.

date Specifies that this is a date-based summertime setting for just

the specified year.

<start-day> Day that the summertime starts, from 1 to 31.

<start-month> First three letters of the name of the month that the

summertime starts.

<start-year> Year that summertime starts, from 2000 to 2035.

<start-time> Time of the day that summertime starts, in the 24-hour time

format HH:MM.

<end-day> Day that summertime ends, from 1 to 31.

<end-month> First three letters of the name of the month that the

summertime ends.

<end-year> Year that summertime ends, from 2000 to 2035.

<end-time> Time of the day that summertime ends, in the 24-hour time

format HH:MM.

<1-180> The offset in minutes.

613-50137-01 Rev A Command Reference for FS980M Series 177

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

CLOCK SUMMER-TIME DATE

Commands

clock summer-time recurring

clock timezone

613-50137-01 Rev A Command Reference for FS980M Series 178

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

CLOCK SUMMER-TIME RECURRING

clock summer-time recurring

Overview This command defines the start and end of summertime for every year, and

specifies summertime’s offset value to Standard Time.

The no variant of this command removes the device’s summertime setting. This

clears both specific summertime dates (set with the clock summer-time date

command) and recurring dates.

By default, the device has no summertime definitions set.

Syntax clock summer-time <timezone-name> recurring <start-week>

<start-day> <start-month> <start-time> <end-week> <end-day>

<end-month> <end-time> <1-180>

no clock summer-time

Parameter Description

<timezone-

name>

A description of the summertime zone, up to 6 characters long.

recurring Specifies that this summertime setting applies every year from

now on.

<start-week> Week of the month when summertime starts, in the range 1-5. The

value 5 indicates the last week that has the specified day in it for

the specified month. For example, to start summertime on the last

Sunday of the month, enter 5 for <start-week> and sun for

<start-day>.

<start-day> Day of the week when summertime starts. Valid values are mon,

tue, wed, thu, fri, sat or sun.

<start-month> First three letters of the name of the month that summertime

starts.

<start-time> Time of the day that summertime starts, in the 24-hour time

format HH:MM.

<end-week> Week of the month when summertime ends, in the range 1-5. The

value 5 indicates the last week that has the specified day in it for

the specified month. For example, to end summertime on the last

Sunday of the month, enter 5 for <end-week> and sun for <end-

day>.

<end-day> Day of the week when summertime ends. Valid values are mon,

tue, wed, thu, fri, sat or sun.

<end-month> First three letters of the name of the month that summertime

ends.

<end-time> Time of the day that summertime ends, in the 24-hour time format

HH:MM.

<1-180> The offset in minutes.

613-50137-01 Rev A Command Reference for FS980M Series 179

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

CLOCK SUMMER-TIME RECURRING

Mode Global Configuration

Examples To set a summertime definition for New Zealand using NZST (UTC+12:00) as the

standard time, and NZDT (UTC+13:00) as summertime, with summertime set to

start on the last Sunday in September, and end on the 1st Sunday in April, use the

command:

awplus(config)# clock summer-time NZDT recurring 5 sun sep 2:00

1 sun apr 2:00 60

To remove any summertime settings on the system, use the command:

awplus(config)# no clock summer-time

Commands

clock summer-time date

clock timezone

613-50137-01 Rev A Command Reference for FS980M Series 180

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

CLOCK TIMEZONE

clock timezone

Overview This command defines the device’s clock timezone. The timezone is set as a offset

to the UTC.

The no variant of this command resets the system time to UTC.

By default, the system time is set to UTC.

Syntax clock timezone <timezone-name> {minus|plus}

[<0-13>|<0-12>:<00-59>]

no clock timezone

Mode Global Configuration

Usage Configure the timezone before setting the local time. Otherwise, when you change

the timezone, the device applies the new offset to the local time.

Examples To set the timezone to New Zealand Standard Time with an offset from UTC of +12

hours, use the command:

awplus(config)# clock timezone NZST plus 12

To set the timezone to Indian Standard Time with an offset from UTC of +5:30

hours, use the command:

awplus(config)# clock timezone IST plus 5:30

To set the timezone back to UTC with no offsets, use the command:

awplus(config)# no clock timezone

Commands

clock set

clock summer-time date

clock summer-time recurring

Parameter Description

<timezone-name> A description of the timezone, up to 6 characters long.

minus orplus The direction of offset from UTC. The minus option

indicates that the timezone is behind UTC. The plus option

indicates that the timezone is ahead of UTC.

<0-13> The offset in hours or from UTC.

<0-12>:<00-59> The offset in hours or from UTC.

613-50137-01 Rev A Command Reference for FS980M Series 181

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

ECOFRIENDLY LED

ecofriendly led

Overview Use this command to enable the eco-friendly LED (Light Emitting Diode) feature,

which turns off power to the port LEDs, including the stack port status LEDs. Power

to the system status and stack management LEDs is not disabled.

Use the no variant of this command to disable the eco-friendly LED feature.

Syntax ecofriendly led

no ecofriendly led

Default The eco-friendly LED feature is disabled by default.

Mode Global Configuration

Usage When the eco-friendly LED feature is enabled, a change in port status will not affect

the display of the associated LED. When the eco-friendly LED feature is disabled

and power is returned to port LEDs, the LEDs will correctly show the current state

of the ports.

In a stacked environment, enabling the eco-friendly LED feature on the stack

master will apply the feature to every member of the stack.

For an example of how to configure a trigger to turn off power to port LEDs, see the

Triggers Feature Overview and Configuration Guide.

Examples To enable the eco-friendly LED feature which turns off power to all port LEDs, use

the following commands:

awplus# configure terminal

awplus(config)# ecofriendly led

To disable the eco-friendly LED feature, use the following command:

awplus# configure terminal

awplus(config)# no ecofriendly led

613-50137-01 Rev A Command Reference for FS980M Series 182

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

FINDME

findme

Overview Use this command to physically locate a specific device from a group of similar

devices. Activating the command causes a selected number of port LEDs to

alternately flash green then amber (if that device has amber LEDs) at a rate of 1 Hz.

Use the no variant of this command to deactivate the Find Me feature prior to the

timeout expiring.

Syntax findme [interface <port-list>|member <stack-ID>] [timeout

<duration>]

no findme

Default By default all port LEDs flash for 60 seconds.

Mode Privileged Exec

Usage Running the findme command causes the device’s port LEDs to flash. An optional

timeout parameter specifies the flash behavior duration. Normal LED behavior is

restored automatically after either the default time, or a specified time has elapsed,

or a no findme command is used. You can specify which interface or interfaces are

flashed with the optional interface parameter.

You can specify a particular stack member with the optional member parameter.

All available interfaces are flashed by default.

NOTE: The interface and member parameters are mutually exclusive.

Example To activate the Find Me feature for the default duration (60 seconds) on all ports,

use the following command:

awplus# findme

To activate the Find Me feature for 120 seconds on all ports, use the following

command:

awplus# findme timeout 120

Parameter Description

interface <port-list> The ports to flash. The port list can be:

•a switch port, e.g. port1.0.4

• a continuous range of ports separated by a hyphen,

e.g. port1.0.1-1.0.4

• a comma-separated list of ports and port ranges,

e.g. port1.0.1,port1.0.5-1.0.6.

member <stack-ID>Stack member number, from 1 to 8.

timeout <duration>How long the LEDs flash, in seconds, in the range 5 to

3600 seconds.

613-50137-01 Rev A Command Reference for FS980M Series 183

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

FINDME

To activate the Find Me feature for the default duration (60 seconds) on switch port

interfaces port1.0.2 through port1.0.4, use the following command:

awplus# findme interface port1.0.2-1.0.4

In the example above, ports 2 to 4 will flash 4 times and then all ports will flash

twice. Each alternate flash will be amber (if that device has amber LEDs). This

pattern will repeat until timeout (default or set) or no findme commands are used.

To deactivate the Find Me feature, use the following command:

awplus# no findme

To activate the Find Me feature for the default duration on stack member 2, use the

following command:

awplus# findme member 2

In the example above, all ports on member 2 will flash 4 times and then all ports in

the stack will flash twice. Each alternate flash will be amber (if that device has

amber LEDs). This pattern will repeat until the timeout (default or set) expires or

the no findme command is used.

613-50137-01 Rev A Command Reference for FS980M Series 184

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

FINDME TRIGGER

findme trigger

Overview When this command is enabled, the LED flashing functionality of the find-me

command is applied whenever any or all of the selected parameter conditions is

detected.

Use the no variant to remove the findme trigger function for the selected

parameter.

Syntax findme trigger {all|loopprot|thrash-limit}

no findme trigger {all|loopprot|thrash-limit}

Default The findme trigger function is disabled.

Mode Global config

Usage Note that findme trigger is not available if you have set the switch to take the

following actions in response to an event:

• For loop detection, the actions log-only and none

• For MAC address thrash-limiting, the actions learn-disable and none.

Example To enable action LED flashing for the loop protection function:

awplus# findme trigger loopprot

Commands

findme

loop-protection loop-detect

Parameter Description

all Enable the find-me function whenever any of the listed parameter

conditions are detected

loopprot Enable the findme function whenever a loop protection condition

is detected.

thrash-limit Enable the findme function whenever a MAC address

thrash-limiting condition is detected.

613-50137-01 Rev A Command Reference for FS980M Series 185

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

HOSTNAME

hostname

Overview This command sets the name applied to the device as shown at the prompt. The

hostname is:

• displayed in the output of the show system command

• displayed in the CLI prompt so you know which device you are configuring

• stored in the MIB object sysName

Use the no variant of this command to revert the hostname setting to its default.

For devices that are not part of an AMF network, the default is “awplus”.

Syntax hostname <hostname>

no hostname [<hostname>]

Default awplus

Mode Global Configuration

Usage On a stack, in a network that is not running AMF, the stack master will have a host

name of “awplus” by default, and this also becomes the name of the stack.

Individual stack members (excluding the master) will have a host name that is the

stack name hyphenated with a numeric suffix. For example, “awplus-1”, “awplus-2”

and so on.

The hostname command can then be used to change the stack name and the

stack master's host name. For example, for the hostname “Lab”, the stack master’s

host name will be “Lab” and the other stack members will have host names “Lab-1”,

“Lab-2” and so on.

In case of stack master fail-over, or stack split, the new stack will use the previous

stack name as its host name and the stack name, unless you change it by executing

the hostname command on the new stack master.

Within an AMF network, any device without a user-defined hostname will

automatically be assigned a name based on its MAC address.

To efficiently manage your network using AMF, we strongly advise that you devise

a naming convention for your network devices and apply an appropriate

hostname to each device.

The name must also follow the rules for ARPANET host names. The name must start

with a letter, end with a letter or digit, and use only letters, digits, and hyphens.

Refer to RFC 1035.

Parameter Description

<hostname> Specifies the name given to a specific device. This is also referred to as

the Node name in AMF output screens.

613-50137-01 Rev A Command Reference for FS980M Series 186

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

HOSTNAME

Example To set the system name to HQ-Sales, use the command:

awplus# configure terminal

awplus(config)# hostname HQ-Sales

This changes the prompt to:

HQ-Sales(config)#

To revert to the default hostname awplus, use the command:

HQ-Sales(config)# no hostname

This changes the prompt to:

awplus(config)#

NOTE: When AMF is configured, running the no hostname command will apply a

hostname that is based on the MAC address of the device node, for example,

node_0000_5e00_5301.

Commands

show system

613-50137-01 Rev A Command Reference for FS980M Series 187

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

NO DEBUG ALL

no debug all

Overview This command disables the debugging facility for all features on your device. This

stops the device from generating any diagnostic debugging messages.

The debugging facility is disabled by default.

Syntax no debug all [ipv6|dot1x|nsm]

Mode Global Configuration and Privileged Exec

Example To disable debugging for all features, use the command:

awplus# no debug all

To disable all 802.1X debugging, use the command:

awplus# no debug all dot1x

To disable all IPv6 debugging, use the command:

awplus# no debug all ipv6

To disable all NSM debugging, use the command:

awplus# no debug all nsm

Commands

undebug all

Parameter Description

dot1x Turns off all debugging for IEEE 802.1X port-based network access-

control.

ipv6 Turns off all debugging for IPv6 (Internet Protocol version 6).

nsm Turns off all debugging for the NSM (Network Services Module).

613-50137-01 Rev A Command Reference for FS980M Series 188

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

REBOOT

reboot

Overview This command halts the device and performs a cold restart (also known as reload).

It displays a confirmation request before restarting.

You can reboot a stand-alone device, a stack, or a specified stack member.

Syntax reboot <stack-ID>

reload <stack-ID>

reboot

reload

Mode Privileged Exec

Usage The reboot and reload commands perform the same action.

When restarting the whole stack, you can either use this reboot command to

reboot all stack members immediately, or to minimize downtime, reboot the stack

members in a rolling sequence by using the reboot rolling command.

Examples To restart a stand-alone device, use the command:

awplus# reboot

reboot system? (y/n): y

To restart all devices in a stack, use the command:

awplus# reboot

Are you sure you want to reboot the whole

stack? (y/n): y

To restart stack member 2, use the command:

awplus# reboot stack-member 2

reboot stack-member 2 system? (y/n): y

If the specified stack member ID does not exist in the current stack, the command

is rejected.

Parameter Description

<stack-ID>Stack member number, from 1 to 8.

613-50137-01 Rev A Command Reference for FS980M Series 189

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

RELOAD

reload

Overview This command performs the same function as the reboot command.

613-50137-01 Rev A Command Reference for FS980M Series 190

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW CLOCK

show clock

Overview This command displays the system’s current configured local time and date. It also

displays other clock related information such as timezone and summertime

configuration.

Syntax show clock

Mode User Exec and Privileged Exec

Example To display the system’s current local time, use the command:

awplus# show clock

Output Figure 5-1: Example output from the show clock command for a device using

New Zealand time

Local Time: Mon, 17 Oct 2016 13:56:06 +1200

UTC Time: Mon, 17 Oct 2016 01:56:06 +0000

Timezone: NZST

Timezone Offset: +12:00

Summer time zone: NZDT

Summer time starts: Last Sunday in September at 02:00:00

Summer time ends: First Sunday in April at 02:00:00

Summer time offset: 60 mins

Summer time recurring: Yes

Table 1: Parameters in the output of the show clock command

Parameter Description

Local Time Current local time.

UTC Time Current UTC time.

Timezone The current configured timezone name.

Timezone Offset Number of hours offset to UTC.

Summer time zone The current configured summertime zone name.

Summer time starts Date and time set as the start of summer time.

Summer time ends Date and time set as the end of summer time.

Summer time offset Number of minutes that summer time is offset from the

system’s timezone.

Summer time

recurring

Whether the device will apply the summer time settings

every year or only once.

613-50137-01 Rev A Command Reference for FS980M Series 191

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW CLOCK

Commands

clock set

clock summer-time date

clock summer-time recurring

clock timezone

613-50137-01 Rev A Command Reference for FS980M Series 192

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW CPU

show cpu

Overview This command displays a list of running processes with their CPU utilization.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show cpu [<stack-ID>] [sort {thrds|pri|sleep|runtime}]

Mode User Exec and Privileged Exec

Examples To show the CPU utilization of current processes, sorting them by the number of

threads the processes are using, use the command:

awplus# show cpu sort thrds

To show CPU utilization for a specific stack member (in this example stack member

2), use the following command:

awplus# show cpu 2

Parameter Description

<stack-ID> Stack member number, from 1 to 8.

sort Changes the sorting order using the following fields. If you do not

specify a field, then the list is sorted by percentage CPU

utilization.

thrds Sort by the number of threads.

pri Sort by the process priority.

sleep Sort by the average time sleeping.

runtime Sort by the runtime of the process.

613-50137-01 Rev A Command Reference for FS980M Series 193

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW CPU

Output Figure 5-2: Example output from show cpu

Stack member 2:



CPU averages:

1 second: 12%, 20 seconds: 2%, 60 seconds: 2%

System load averages:

1 minute: 0.03, 5 minutes: 0.02, 15 minutes: 0.00

Current CPU load:

userspace: 6%, kernel: 4%, interrupts: 1% iowaits: 0%



user processes

==============

pid name thrds cpu% pri state sleep% runtime

1544 hostd 1 2.8 20 run 0 120

1166 exfx 17 1.8 20 sleep 0 3846

1198 stackd 1 0.9 20 sleep 0 459

1284 aisexec 44 0.9 -2 sleep 0 2606

1 init 1 0.0 20 sleep 0 120

9772 sh 1 0.0 20 sleep 0 0

9773 corerotate 1 0.0 20 sleep 0 0

853 syslog-ng 1 0.0 20 sleep 0 356

859 klogd 1 0.0 20 sleep 0 1

910 inetd 1 0.0 20 sleep 0 3

920 portmap 1 0.0 20 sleep 0 0

931 crond 1 0.0 20 sleep 0 1

1090 openhpid 11 0.0 20 sleep 0 233

1111 hpilogd 1 0.0 20 sleep 0 0

1240 hsl 1 0.0 20 sleep 0 79

1453 authd 1 0.0 20 sleep 0 85

...

Table 2: Parameters in the output of the show cpu command

Parameter Description

Stack member Stack member number.

CPU averages Average CPU utilization for the periods stated.

System load

averages

The average number of processes waiting for CPU time for the

periods stated.

Current CPU

load

Current CPU utilization specified by load types.

pid Identifier number of the process.

name A shortened name for the process

thrds Number of threads in the process.

cpu% Percentage of CPU utilization that this process is consuming.

pri Process priority state.

613-50137-01 Rev A Command Reference for FS980M Series 194

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW CPU

Commands

show memory

show memory allocations

show memory history

show memory pools

show process

state Process state; one of “run”, “sleep”, “zombie”, and “dead”.

sleep% Percentage of time that the process is in the sleep state.

runtime The time that the process has been running for, measured in

jiffies. A jiffy is the duration of one tick of the system timer

interrupt.

Table 2: Parameters in the output of the show cpu command (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 195

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW CPU HISTORY

show cpu history

Overview This command prints a graph showing the historical CPU utilization.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show [<stack-ID>] cpu history

Mode User Exec and Privileged Exec

Usage This command’s output displays three graphs of the percentage CPU utilization:

• per second for the last minute, then

• per minute for the last hour, then

• per 30 minutes for the last 30 hours.

If this command is entered on the stack master, it will print graphs for all the stack

members. A stack member heading will be displayed to distinguish the different

graphs for every stack member.

Examples To display a graph showing the historical CPU utilization of the device, use the

command:

awplus# show cpu history

To display the CPU utilization history graph for stack member 2, use the command:

awplus# show 2 cpu history

where 2 is the node id of the stack member.

Parameter Description

<stack-ID>Stack member number, from 1 to 8.

613-50137-01 Rev A Command Reference for FS980M Series 196

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW CPU HISTORY

Output Figure 5-3: Example output from the show cpu history command

Per second CPU load history



100

90

80

70

60

50

40

30

20 *

10 ******************************************* ****************

|....|....|....|....|....|....|....|....|....|....|....|....

Oldest Newest

CPU load% per second (last 60 seconds)

* = average CPU load%

Per minute CPU load history



100

90

80

70

60 +

50

40

30

20 ++ +++++++++ +++++++ ++++ + ++++++ ++++ +++ +++++ +++++++++

10 ************************************************************

|....|....|....|....|....|....|....|....|....|....|....|....

Oldest Newest

CPU load% per minute (last 60 minutes)

* = average CPU load%, + = maximum

Per (30) minute CPU load history



100

90

80

70 +

60

50

40

30

20

10 ***

|....|....|....|....|....|....|....|....|....|....|....|....

Oldest Newest

CPU load% per 30 minutes (last 60 values / 30 hours)

* = average, - = minimum, + = maximum

613-50137-01 Rev A Command Reference for FS980M Series 197

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW CPU HISTORY

Commands

show memory

show memory allocations

show memory pools

show process

613-50137-01 Rev A Command Reference for FS980M Series 198

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW DEBUGGING

show debugging

Overview This command displays information for all debugging options.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show debugging

Default This command runs all the show debugging commands in alphabetical order.

Mode User Exec and Privileged Exec

Usage This command displays all debugging information, similar to the way the show

tech-support command displays all show output for use by Allied Telesis

authorized service personnel only.

Example To display all debugging information, use the command:

awplus# show debugging

Output Figure 5-4: Example output from the show debugging command

awplus#show debugging

AAA debugging status:

Authentication debugging is off

Accounting debugging is off



% DHCP Snooping service is disabled



802.1X debugging status:



EPSR debugging status:

EPSR Info debugging is off

EPSR Message debugging is off

EPSR Packet debugging is off

EPSR State debugging is off



IGMP Debugging status:

IGMP Decoder debugging is off

IGMP Encoder debugging is off

...

613-50137-01 Rev A Command Reference for FS980M Series 199

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW ECOFRIENDLY

show ecofriendly

Overview This command displays the switch’s eco-friendly configuration status. The

ecofriendly led configuration status are shown in the show ecofriendly output.

Syntax show ecofriendly

Mode Privileged Exec and Global Configuration

Example To display the switch’s eco-friendly configuration status, use the following

command:

awplus# show ecofriendly

Output Figure 5-5: Example output from the show ecofriendly command

awplus#show ecofriendly 

Front panel port LEDs normal



Energy efficient ethernet

Port Name Configured Status

port1.0.1 Port 1 off -

port1.0.2 off off

port1.0.3 off -

port1.0.4 Port 4 off -

port1.0.5 off -

...

Table 3: Parameters in the output of the show ecofriendly command

Parameter Description

normal The eco-friendly LED feature is disabled and port LEDs

show the current state of the ports. This is the default

setting.

off The eco-friendly LED feature is enabled and power to

the port LEDs is disabled.

Port Displays the port number as assigned by the switch.

Name Displays the port name if a name is configured for a

port number.

Configured Because LPI is not supported, this entry always shows

“off” or a dash (-).

Status Because LPI is not supported, this entry always shows

“off” or a dash (-).

613-50137-01 Rev A Command Reference for FS980M Series 200

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW INTERFACE MEMORY

show interface memory

Overview This command displays the shared memory used by either all interfaces, or the

specified interface or interfaces. The output is useful for diagnostic purposes by

Allied Telesis authorized service personnel.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show interface memory

show interface <port-list> memory

Mode User Exec and Privileged Exec

Example To display the shared memory used by all interfaces, use the command:

awplus# show interface memory

To display the shared memory used by port1.0.1 and port1.0.5 to port1.0.6, use the

command:

awplus# show interface port1.0.1,port1.0.5-1.0.6 memory

Parameter Description

<port-list> Display information about only the specified port or ports. The port

list can be:

• a switch port (e.g. port1.0.4), a static channel group (e.g. sa2) or a

dynamic (LACP) channel group (e.g. po2)

• a continuous range of ports separated by a hyphen (e.g.

port1.0.1-1.0.4, or sa1-2, or po1-2)

• a comma-separated list of ports and port ranges (e.g.

port1.0.1,port1.0.4-1.0.6). Do not mix switch ports, static channel

groups, and dynamic (LACP) channel groups in the same list.

613-50137-01 Rev A Command Reference for FS980M Series 201

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW INTERFACE MEMORY

Output Figure 5-6: Example output from the show interface memory command

Figure 5-7: Example output from show interface <port-list> memory for a list

of interfaces

Commands

show interface brief

show interface status

show interface switchport

awplus#show interface memory

Vlan blocking state shared memory usage

---------------------------------------------

Interface shmid Bytes Used nattch Status

port1.0.1 393228 512 1

port1.0.2 458766 512 1

port1.0.3 360459 512 1

port1.0.4 524304 512 1

port1.0.5 491535 512 1

port1.0.6 557073 512 1

...

lo 425997 512 1

po1 1179684 512 1

po2 1212453 512 1

sa3 1245222 512 1

awplus#show interface port1.0.1,port1.0.5-1.0.6 memory

Vlan blocking state shared memory usage

---------------------------------------------

Interface shmid Bytes Used nattch Status

port1.0.1 393228 512 1

port1.0.5 491535 512 1

port1.0.6 557073 512 1

613-50137-01 Rev A Command Reference for FS980M Series 202

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW MEMORY

show memory

Overview This command displays the memory used by each process that is currently running

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show memory [<stack-ID>] [sort {size|peak|stk}]

Mode User Exec and Privileged Exec

Example To display the memory used by the current running processes, use the command:

awplus# show memory

Output Figure 5-8: Example output from show memory

Parameter Description

<stack-ID>Stack member number, from 1 to 8.

sort Changes the sorting order for the list of processes. If you do not

specify this, then the list is sorted by percentage memory

utilization.

size Sort by the amount of memory the process is

currently using.

peak Sort by the amount of memory the process is

currently using.

stk Sort by the stack size of the process.

awplus#show memory



Stack member 1:



RAM total: 514920 kB; free: 382716; buffers: 16368 kB



user processes

==============

pid name mem% size peak data stk

962 pss 6 33112 36260 27696 244

1 init 0 348 1092 288 84

797 syslog-ng 0 816 2152 752 84

803 klogd 0 184 1244 124 84

843 inetd 0 256 1256 136 84

...

613-50137-01 Rev A Command Reference for FS980M Series 203

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW MEMORY

Commands

show memory allocations

show memory history

show memory pools

show memory shared

Table 4: Parameters in the output of the show memory command

Parameter Description

Stack member Stack member number.

RAM total Total amount of RAM memory free.

free Available memory size.

buffers Memory allocated kernel buffers.

pid Identifier number for the process.

name Short name used to describe the process.

mem% Percentage of memory utilization the process is currently using.

size Amount of memory currently used by the process.

peak Greatest amount of memory ever used by the process.

data Amount of memory used for data.

stk The stack size.

613-50137-01 Rev A Command Reference for FS980M Series 204

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW MEMORY ALLOCATIONS

show memory allocations

Overview This command displays the memory allocations used by processes.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show memory allocations [<process>]

Mode User Exec and Privileged Exec

Example To display the memory allocations used by all processes on your device, use the

command:

awplus# show memory allocations

Output Figure 5-9: Example output from the show memory allocations command

Parameter Description

<process> Displays the memory allocation used by the specified process.

awplus#show memory allocations

Memory allocations for imi

-----------------------------



Current 15093760 (peak 15093760)



Statically allocated memory:

- binary/exe : 1675264

- libraries : 8916992

- bss/global data : 2985984

- stack : 139264



Dynamically allocated memory (heap):

- total allocated : 1351680

- in use : 1282440

- non-mmapped : 1351680

- maximum total allocated : 1351680

- total free space : 69240

- releasable : 68968

- space in freed fastbins : 16



Context

filename:line allocated freed

+ lib.c:749 484

.

613-50137-01 Rev A Command Reference for FS980M Series 205

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW MEMORY ALLOCATIONS

Commands

show memory

show memory history

show memory pools

show memory shared

show tech-support

613-50137-01 Rev A Command Reference for FS980M Series 206

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW MEMORY HISTORY

show memory history

Overview This command prints a graph showing the historical memory usage.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show memory history [<stack-ID>]

Mode User Exec and Privileged Exec

Usage This command’s output displays three graphs of the percentage memory

utilization:

• per second for the last minute, then

• per minute for the last hour, then

• per 30 minutes for the last 30 hours.

Examples To show a graph displaying the historical memory usage for either a single

unstacked device, or a complete stack, use the command:

awplus# show memory history

To show a graph displaying the historical memory usage for specific stack member

(stack member 2 in this example) within a stack, use the command:

awplus# show memory history 2

Parameter Description

<stack-ID>Stack member number, from 1 to 8.

613-50137-01 Rev A Command Reference for FS980M Series 207

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW MEMORY HISTORY

Output Figure 5-10: Example output from the show memory history command

Commands

show memory allocations

show memory pools

show memory shared

show tech-support

STACK member 1:



Per minute memory utilization history



100

90

80

70

60

50

40*************************************************************

30

20

10

|....|....|....|....|....|....|....|....|....|....|....|....

Oldest Newest

Memory utilization% per minute (last 60 minutes)

* = average memory utilisation%.

...

613-50137-01 Rev A Command Reference for FS980M Series 208

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW MEMORY POOLS

show memory pools

Overview This command shows the memory pools used by processes.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show memory pools [<process>]

Mode User Exec and Privileged Exec

Example To shows the memory pools used by processes, use the command:

awplus# show memory pools

Output Figure 5-11: Example output from the show memory pools command

Commands

show memory allocations

show memory history

show tech-support

Parameter Description

<process> Displays the memory pools used by the specified process.

awplus#show memory pools

Memory pools for imi

----------------------



Current 15290368 (peak 15290368)



Statically allocated memory:

- binary/exe : 1675264

- libraries : 8916992

- bss/global data : 2985984

- stack : 139264



Dynamically allocated memory (heap):

- total allocated : 1548288

- in use : 1479816

- non-mmapped : 1548288

- maximum total allocated : 1548288

- total free space : 68472

- releasable : 68200

- space in freed fastbins : 16

.

613-50137-01 Rev A Command Reference for FS980M Series 209

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW MEMORY SHARED

show memory shared

Overview This command displays shared memory allocation information. The output is

useful for diagnostic purposes by Allied Telesis authorized service personnel.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show memory shared

Mode User Exec and Privileged Exec

Example To display information about the shared memory allocation used on the device,

use the command:

awplus# show memory shared

Output Figure 5-12: Example output from the show memory shared command

Commands

show memory allocations

show memory history

show memory

awplus#show memory shared

Shared Memory Status

--------------------------

Segment allocated = 39

Pages allocated = 39

Pages resident = 11



Shared Memory Limits

--------------------------

Maximum number of segments = 4096

Maximum segment size (kbytes) = 32768

Maximum total shared memory (pages) = 2097152

Minimum segment size (bytes) = 1

613-50137-01 Rev A Command Reference for FS980M Series 210

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW PROCESS

show process

Overview This command lists a summary of the current running processes.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show process [<stack-ID>] [sort {cpu|mem}]

Mode User Exec and Privileged Exec

Examples To show a graph displaying the historical memory usage for either a single

unstacked device, or a complete stack, use the command:

awplus# show memory history

To show a graph displaying the historical memory usage for specific stack member

(stack member 2 in this example) within a stack, use the command:

awplus# show memory history 2

Example To display a summary of the current running processes, use the command:

awplus# show process

To display a summary of the current running processes on stack member 2, use the

command:

awplus# show process 2

Parameter Description

<stack-ID>Stack member number, from 1 to 8.

sort Changes the sorting order for the list of processes.

cpu Sorts the list by the percentage of CPU utilization.

mem Sorts the list by the percentage of memory

utilization.

613-50137-01 Rev A Command Reference for FS980M Series 211

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW PROCESS

Output Figure 5-13: Example output from the show process command

Stack member 2:



CPU averages:

1 second: 8%, 20 seconds: 5%, 60 seconds: 5%

System load averages:

1 minute: 0.04, 5 minutes: 0.08, 15 minutes: 0.12

Current CPU load:

userspace: 9%, kernel: 9%, interrupts: 0% iowaits: 0%

RAM total: 514920 kB; free: 382600 kB; buffers: 16368 kB



user processes

==============

pid name thrds cpu% mem% pri state sleep% 

962 pss 12 0 6 25 sleep 5 

1 init 1 0 0 25 sleep 0 

797 syslog-ng 1 0 0 16 sleep 88 

...

kernel threads

==============

pid name cpu% pri state sleep% 

71 aio/0 0 20 sleep 0 

3 events/0 0 10 sleep 98 

...

Table 5: Parameters in the output from the show process command

Parameter Description

Stack member Stack member number.

CPU averages Average CPU utilization for the periods stated.

System load

averages

The average number of processes waiting for CPU time for the

periods stated.

Current CPU

load

Current CPU utilization specified by load types

RAM total Total memory size.

free Available memory.

buffers Memory allocated to kernel buffers.

pid Identifier for the process.

name Short name to describe the process.

thrds Number of threads in the process.

cpu% Percentage of CPU utilization that this process is consuming.

mem% Percentage of memory utilization that this process is consuming.

613-50137-01 Rev A Command Reference for FS980M Series 212

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW PROCESS

Commands

show cpu

show cpu history

pri Process priority.

state Process state; one of “run”, “sleep”, “stop”, “zombie”, or “dead”.

sleep% Percentage of time the process is in the sleep state.

Table 5: Parameters in the output from the show process command (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 213

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW REBOOT HISTORY

show reboot history

Overview Use this command to display the device’s reboot history.

Syntax show reboot history [<stack-ID>]

Mode User Exec and Privileged Exec

Example To show the reboot history of stack member 2, use the command:

awplus# show reboot history 2

Output Figure 5-14: Example output from the show reboot history command

Commands

show tech-support

Parameter Description

<stack-ID>Stack member number, from 1 to 8.

awplus#show reboot history 2



Stack member 2:



<date> <time> <type> <description>

-----------------------------------------------

2016-10-10 01:42:04 Expected User Request

2016-10-10 01:35:31 Expected User Request

2016-10-10 01:16:25 Unexpected Rebooting due to critical process (network/nsm) 

failure!

2016-10-10 01:11:04 Unexpected Rebooting due to critical process (network/nsm) 

failure!

2016-10-09 20:46:40 Unexpected Rebooting due to VCS duplicate member-ID

2016-10-09 19:56:16 Expected User Request

2016-10-09 20:36:06 Unexpected Rebooting due to VCS duplicate master (Continuous 

reboot prevention)

2016-10-09 19:51:20 Expected User Request

Table 6: Parameters in the output from the show reboot history command

Parameter Description

Unexpected A non-intended reboot.

Expected A planned or user-triggered reboot.

User request User initiated reboot via the CLI.

613-50137-01 Rev A Command Reference for FS980M Series 214

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW ROUTER-ID

show router-id

Overview Use this command to show the Router ID of the current system.

Syntax show router-id

Mode User Exec and Privileged Exec

Example To display the Router ID of the current system, use the command:

awplus# show router-id

Output Figure 5-15: Example output from the show router-id command

awplus>show router-id

Router ID: 10.55.0.2 (automatic)

613-50137-01 Rev A Command Reference for FS980M Series 215

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW SYSTEM

show system

Overview This command displays general system information about the device, including

the hardware, installed, memory, and software versions loaded. It also displays

location and contact details when these have been set.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show system

Mode User Exec and Privileged Exec

Example To display configuration information, use the command:

awplus# show system

Output Figure 5-16: Example output from show system

Commands

show system environment



awplus#show system

System Status Wed Oct 19 02:26:49 2016



Board ID Bay Board Name Rev Serial number

--------------------------------------------------------------------------------

Base 482 AT-FS980M/52PS X1-0 FS980M52PS000009

--------------------------------------------------------------------------------

RAM: Total: 477252 kB Free: 368184 kB

Flash: 112.8MB Used: 3.4MB Available: 109.4MB

--------------------------------------------------------------------------------

Environment Status : Normal

Uptime : 0 days 00:22:25

Bootloader version : 5.1.3



Current software : FS980-5.4.6-1.5.rel

Software version : 5.4.6-1.5

Build date : Fri Sep 30 05:35:20 UTC 2016



Current boot config: flash:/default.cfg (file exists)



System Name

awplus

System Contact



System Location

613-50137-01 Rev A Command Reference for FS980M Series 216

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW SYSTEM ENVIRONMENT

show system environment

Overview This command displays the current environmental status of your device and any

attached PSU, XEM, or other expansion option. The environmental status covers

information about temperatures, fans, and voltage.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show system environment

Mode User Exec and Privileged Exec

Example To display the system’s environmental status, use the command:

awplus# show system environment

Output Figure 5-17: Example output from the show system environment command

Commands

show system

awplus#show system environment

Environment Monitoring Status



Overall Status: Normal



Resource ID: 1 Name: AT-FS980M/52PS

ID Sensor (Units) Reading Low Limit High Limit Status

1 Fan: Fan 1 (Rpm) 1650 500 - Ok

2 Fan: Fan 2 (Rpm) 1700 500 - Ok

3 Fan: Fan 3 (Rpm) 1850 500 - Ok

4 Fan: Fan 4 (Rpm) 1700 500 - Ok

5 Temp: Temp 1 (Degrees C) 31 57(Hyst) 62 Ok

6 Temp: Temp 2 (Degrees C) 26 57(Hyst) 62 Ok

613-50137-01 Rev A Command Reference for FS980M Series 217

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW SYSTEM INTERRUPTS

show system interrupts

Overview Use this command to display the number of interrupts for each IRQ (Interrupt

Request) used to interrupt input lines on a PIC (Programmable Interrupt Controller)

on your device.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show system interrupts

Mode User Exec and Privileged Exec

Example To display information about the number of interrupts for each IRQ in your device,

use the command:

awplus# show system interrupts

Output Figure 5-18: Example output from the show system interrupts command

Commands

show system environment

awplus#show system interrupts



CPU0

1: 2040274 GIC 27 Edge Disabled 1 iproc_gtimer

2: 5705 GIC 105 Level Enabled 0 serial

4: 1 GIC 104 Level Enabled 0 ehci_hcd:usb1, ohci_hcd:usb2

5: 0 GIC 117 Level Enabled 0 18008000.i2c

6: 0 GIC 118 Level Enabled 0 3200000.i2c

7: 3 GIC 116 Level Enabled 0 gpio_ccg

8: 48961 GIC 221 Level Enabled 0 linux-kernel-bde

9: 0 pca953x 0 Edge Enabled 0 pluggable-detect



Err: 0

...

613-50137-01 Rev A Command Reference for FS980M Series 218

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW SYSTEM MAC

show system mac

Overview This command displays the physical MAC address available on a standalone

switch, or a stack. This command also shows the virtual MAC address for a stack if

the stack virtual MAC address feature is enabled with the stack virtual-mac or the

stack enable command.

Syntax show system mac

Mode User Exec and Privileged Exec

Usage For more information about the virtual MAC address feature, see the VCStack

Feature Overview and Configuration Guide.

Example To display the physical MAC address enter the following command:

awplus# show system mac

Output Figure 5-19: Example output from the show system mac command

Output Figure 5-20: Example output showing how to use the stack virtual-mac

command and the show system mac command

Commands

stack virtual-mac

awplus#show system mac

eccd.6d9d.4eed (system)

awplus#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

awplus(config)#stack virtual-mac

% Please check that the new MAC 0000.cd37.0065 is unique within 

the network.

% Save the config and restart the system for this change to take 

effect.

Member1#copy run start

Building configuration...

[OK]

Member1#reload

reboot system? (y/n): y



... Rebooting at user request ...

Loading default configuration ....



awplus login: manager

Password:



awplus>show system mac

eccd.6d9d.4eed



Virtual MAC Address 0000.cd37.0065

613-50137-01 Rev A Command Reference for FS980M Series 219

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW SYSTEM SERIALNUMBER

show system serialnumber

Overview This command shows the serial number information for the device.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show system serialnumber

Mode User Exec and Privileged Exec

Example To display the serial number information for the device, use the command:

awplus# show system serialnumber

Output Figure 5-21: Example output from the show system serial number command

awplus#show system serialnumber

45AX5300X

613-50137-01 Rev A Command Reference for FS980M Series 220

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW TECH-SUPPORT

show tech-support

Overview This command generates system and debugging information for the device and

saves it to a file.

You can optionally limit the command output to display only information for a

given protocol or feature. The features available depend on your device and will be

a subset of the features listed in the table below.

The command generates a large amount of output, which is saved to a file in

compressed format. The output file name can be specified by outfile option. If the

output file already exists, a new file name is generated with the current time stamp.

If the output filename does not end with “.gz”, then “.gz” is appended to the

filename. Since output files may be too large for Flash on the device we

recommend saving files to external memory or a TFTP server whenever possible to

avoid device lockup. This method is not likely to be appropriate when running the

working set option of AMF across a range of physically separated devices.

Syntax show tech-support

{[all|atmf|auth|bgp|card|dhcpsn|epsr|firewall|igmp|ip|ipv6|mld

update]} [outfile <filename>]

Parameter Description

all Display full information

atmf Display ATMF-specific information

auth Display authentication-related information

bgp Display BGP-related information

card Display Chassis Card specific information

dhcpsn Display DHCP Snooping specific information

epsr Display EPSR specific information

firewall Display firewall specific information

igmp Display IGMP specific information

ip Display IP specific information

ipv6 Display IPv6 specific information

mld Display MLD specific information

openflow Display information related to OpenFlow

ospf Display OSPF related information

ospf6 Display OSPF6 specific information

pim Display PIM related information

rip RIP related information

613-50137-01 Rev A Command Reference for FS980M Series 221

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SHOW TECH-SUPPORT

Default Captures all information for the device.

By default the output is saved to the file ‘tech-support.txt.gz’ in the current

directory. If this file already exists in the current directory then a new file is

generated with the time stamp appended to the file name, for example

‘tech-support20161009.txt.gz’, so the previous file is retained.

Usage This command is useful for collecting a large amount of information about all

protocols or specific protocols on your device so that it can then be analyzed for

troubleshooting purposes. The output of this command can be provided to

technical support staff when reporting a problem.

Mode Privileged Exec

Examples To produce the output needed by technical support staff, use the command:

awplus# show tech-support

ripng Display RIPNG specific information

stack Display stacking device information

stp Display STP specific information

system Display general system information

tacacs+ Display TACACS+ information

update Display resource update specific information

|Output modifier

>Output redirection

>> Output redirection (append)

outfile Output file name

<filename>Specifies a name for the output file. If no name is specified, this file

will be saved as: tech-support.txt.gz.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 222

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SPEED (ASYN)

speed (asyn)

Overview This command changes the console speed from the device. Note that a change in

console speed is applied for subsequent console sessions. Exit the current session

to enable the console speed change using the clear line console command.

Syntax speed <console-speed-in-bps>

Default The default console speed baud rate is 9600 bps.

Mode Line Configuration

Usage This command is used to change the console (asyn) port speed. Set the console

speed to match the transmission rate of the device connected to the console (asyn)

port on your device.

Example To set the terminal console (asyn0) port speed from the device to 57600 bps, then

exit the session, use the commands:

awplus# configure terminal

awplus(config)# line console 0

awplus(config-line)# speed 57600

awplus(config-line)# exit

awplus(config)# exit

awplus# exit

Then log in again to enable the change:

awplus login:

Password:

awplus>

Parameter Description

<console-speed-in-bps>Console speed Baud rate in bps (bits per second).

1200 1200 Baud

2400 2400 Baud

9600 9600 Baud

19200 19200 Baud

38400 38400 Baud

57600 57600 Baud

115200 115200 Baud

613-50137-01 Rev A Command Reference for FS980M Series 223

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

SPEED (ASYN)

Commands

clear line console

line

show running-config

show startup-config

speed

613-50137-01 Rev A Command Reference for FS980M Series 224

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

TERMINAL MONITOR

terminal monitor

Overview Use this command to display debugging output on a terminal.

To display the cursor after a line of debugging output, press the Enter key.

Use the command terminal no monitor to stop displaying debugging output on

the terminal, or use the timeout option to stop displaying debugging output on

the terminal after a set time.

Syntax terminal monitor [<1-60>]

terminal no monitor

Default Disabled

Mode User Exec and Privileged Exec

Examples To display debugging output on a terminal, enter the command:

awplus# terminal monitor

To specify timeout of debugging output after 60 seconds, enter the command:

awplus# terminal monitor 60

To stop displaying debugging output on the terminal, use the command:

awplus# terminal no monitor

Commands

All debug commands

Parameter Description

<1-60>Set a timeout between 1 and 60 seconds for terminal output.

613-50137-01 Rev A Command Reference for FS980M Series 225

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SYSTEM CONFIGURATION AND MONITORING COMMANDS

UNDEBUG ALL

undebug all

Overview This command applies the functionality of the no debug all command.

613-50137-01 Rev A Command Reference for FS980M Series 226

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Pluggables and

Cabling Commands

Introduction

Overview This chapter provides an alphabetical reference of commands used to configure

and monitor Pluggables and Cabling, including:

• Optical Digital Diagnostic Monitoring (DDM) to help find fiber issues when

links go down

For more information, see the Pluggables and Cabling Feature Overview and

Configuration Guide.

Command List •“clear test cable-diagnostics tdr” on page 227

•“show system pluggable” on page 228

•“show system pluggable detail” on page 230

•“show system pluggable diagnostics” on page 233

•“show test cable-diagnostics tdr” on page 235

•“test cable-diagnostics tdr interface” on page 236

613-50137-01 Rev A Command Reference for FS980M Series 227

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PLUGGABLES AND CABLING COMMANDS

CLEAR TEST CABLE-DIAGNOSTICS TDR

clear test cable-diagnostics tdr

Overview Use this command to clear the results of the last cable test that was run.

Syntax clear test cable-diagnostics tdr

Mode Privileged Exec

Examples To clear the results of a previous cable-diagnostics test use the following

commands:

awplus# clear test cable-diagnostics tdr

Commands

show test cable-diagnostics tdr

test cable-diagnostics tdr interface

613-50137-01 Rev A Command Reference for FS980M Series 228

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PLUGGABLES AND CABLING COMMANDS

SHOW SYSTEM PLUGGABLE

show system pluggable

Overview This command displays brief pluggable transceiver information showing the

pluggable type, the pluggable serial number, and the pluggable port on the

device. Different types of pluggable transceivers are supported in different models

of device. See your Allied Telesis dealer for more information about the models of

pluggables that your device supports.

Syntax show system pluggable [<port-list>]

Mode User Exec and Privileged Exec

Example To display brief information about all installed pluggable transceivers, use the

command:

awplus# show system pluggable

Output Figure 6-1: Example output from show system pluggable

Parameter Description

<port-list> The ports to display information about. The port list can be:

• a switch port (e.g. port1.0.25)

• a continuous range of ports separated by a hyphen (e.g.

port1.0.27-1.0.28)

• a comma-separated list of ports and port ranges (e.g.

port1.0.25,port1.0.27-1.0.28)

awplus#show system pluggable 

System Pluggable Information



Port Vendor Device Serial Number Datecode Type

--------------------------------------------------------------------------------

1.0.27 TE Connectivity AT-StackXS/1.0 13140191 13040300 1xCOPPER PAS

1.0.28 TE Connectivity AT-StackXS/1.0 13140232 13040300 1xCOPPER PAS

--------------------------------------------------------------------------------

Table 1: Parameters in the output from the show system pluggable command

Parameter Description

Stack member The stack member number.

Port Specifies the vendor’s name for the installed pluggable

transceiver.

Vendor Name Specifies the vendor’s name for the installed pluggable

transceiver.

613-50137-01 Rev A Command Reference for FS980M Series 229

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PLUGGABLES AND CABLING COMMANDS

SHOW SYSTEM PLUGGABLE

Commands

show system environment

show system pluggable detail

show system pluggable diagnostics

Device Name Specifies the device name for the installed pluggable

transceiver.

Device Type Specifies the device type for the installed pluggable

transceiver.

Serial Number Specifies the serial number for the installed pluggable

transceiver.

Manufacturing Datecode Specifies the manufacturing datecode for the installed

pluggable transceiver. Checking the manufacturing

datecode with the vendor may be useful when

determining Laser Diode aging issues.For more

information, see ”How To Troubleshoot Fiber and

Pluggable Issues” in the “Getting Started with AlliedWare

Plus” Feature Overview and Configuration Guide.

SFP Laser Wavelength Specifies the laser wavelength of the installed pluggable

transceiver.

Datecode Specifies the manufacturing datecode for the installed

pluggable transceiver. Checking the manufacturing

datecode with the vendor may be useful when

determining Laser Diode aging issues. For more

information, see ”How To Troubleshoot Fiber and

Pluggable Issues” in the “Getting Started with AlliedWare

Plus” Feature Overview and Configuration Guide.

Device Type Specifies the device type for the installed pluggable

transceiver

Table 1: Parameters in the output from the show system pluggable command

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 230

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PLUGGABLES AND CABLING COMMANDS

SHOW SYSTEM PLUGGABLE DETAIL

show system pluggable detail

Overview This command displays detailed pluggable transceiver information showing the

pluggable type, the pluggable serial number, and the pluggable port on the

device. Different types of pluggable transceivers are supported in different models

of device. See your Allied Telesis dealer for more information about the models of

pluggables that your device supports.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show system pluggable [<port-list>] detail

Mode User Exec and Privileged Exec

Usage In addition to the information about pluggable transceivers displayed using the

show system pluggable command (port, manufacturer, serial number,

manufacturing datecode, and type information), the show system pluggable

detail command displays the following information:

•SFP Laser Wavelength: Specifies the laser wavelength of the installed

pluggable transceiver

•Single mode Fiber: Specifies the link length supported by the pluggable

transceiver using single mode fiber

•OM1 (62.5μ m) Fiber: Specifies the link length, in meters (m) or kilometers

(km) supported by the pluggable transceiver using 62.5 micron multi-mode

fiber.

•OM2 (50μ m) Fiber: Specifies the link length (in meters or kilometers)

supported by the pluggable transceiver using 50 micron multi-mode fiber.

•Diagnostic Calibration: Specifies whether the pluggable transceiver

supports DDM or DOM Internal or External Calibration.

–Internal is displayed if the pluggable transceiver supports DDM or

DOM Internal Calibration.

–External is displayed if the pluggable transceiver supports DDM or

DOM External Calibration.

– a dash (-) is displayed if neither Internal Calibration or External

Calibration is supported.

Parameter Description

<port-list> The ports to display information about. The port list can be:

• a switch port (e.g. port1.0.25)

• a continuous range of ports separated by a hyphen (e.g.

port1.0.27-1.0.28)

• a comma-separated list of ports and port ranges (e.g.

port1.0.25,port1.0.27-1.0.28)

613-50137-01 Rev A Command Reference for FS980M Series 231

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PLUGGABLES AND CABLING COMMANDS

SHOW SYSTEM PLUGGABLE DETAIL

•Power Monitoring: Displays the received power measurement type, which

can be either OMA(Optical Module Amplitude) or Avg(Average Power)

measured in μW.

NOTE: For parameters that are not supported or not specified, a hyphen is displayed

instead.

Example To display detailed information about the pluggable transceivers installed in a

particular port on the device, use a command like:

To display detailed information about all the pluggable transceivers installed on

the device, use the command:

awplus# show system pluggable detail

Output Figure 6-2: Example output from the show system pluggable detail

command for a specific port on a device

awplus#show system pluggable port1.0.5 detail

System Pluggable Information Detail



Stack member 1



port1.0.27

==========

Vendor Name: TE Connectivity

Device Name: AT-StackXS/1.0

Device Revision: B

Device Type: 1xCOPPER PAS

Serial Number: 13140191

Manufacturing Datecode: 13040300

SFP Laser Wavelength: 256nm

Link Length Supported

Single Mode Fiber : -

OM1 (62.5um) Fiber: -

OM2 (50um) Fiber : -

OM3 (50um) Fiber : -

Diagnostic Calibration: -

Power Monitoring: -

Table 2: Parameters in the output from the show system pluggable detail

command:

Parameter Description

Port Specifies the port the pluggable transceiver is installed in.

Vendor Name Specifies the vendor’s name for the installed pluggable

transceiver.

Device Name Specifies the device name for the installed pluggable

transceiver.

613-50137-01 Rev A Command Reference for FS980M Series 232

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PLUGGABLES AND CABLING COMMANDS

SHOW SYSTEM PLUGGABLE DETAIL

Commands

show system environment

show system pluggable

show system pluggable diagnostics

Device Revision Specifies the hardware revision code for the pluggable

transceiver. This may be useful for troubleshooting because

different devices may support different pluggable

transceiver revisions.

Device Type Specifies the device type for the installed pluggable

transceiver..

Serial Number Specifies the serial number for the installed pluggable

transceiver.

Manufacturing

Datecode

Specifies the manufacturing datecode for the installed

pluggable transceiver. Checking the manufacturing

datecode with the vendor may be useful when

determining Laser Diode aging issues. For more

information, see ”How To Troubleshoot Fiber and

Pluggable Issues” in the “Getting Started with AlliedWare

Plus” Feature Overview and Configuration Guide.

SFP Laser Wavelength Specifies the laser wavelength of the installed pluggable

transceiver.

Single Mode Fiber Specifies the link length supported by the pluggable

transceiver using single mode fiber.

OM1 (62.5um) Fiber Specifies the link length (in μm - micron) supported by the

pluggable transceiver using 62.5 micron multi-mode fiber.

OM2 (50um) Fiber Specifies the link length (in μm - micron) supported by the

pluggable transceiver using 50 micron multi-mode fiber.

Diagnostic Calibration Specifies whether the pluggable transceiver supports DDM

or DOM Internal or External Calibration:

Internal is displayed if the pluggable transceiver supports

DDM or DOM Internal Calibration.

External is displayed if the pluggable transceiver supports

DDM or DOM External Calibration.

- is displayed if neither Internal Calibration or External

Calibration is supported.

Power Monitoring Displays the received power measurement type, which can

be either OMA (Optical Module Amplitude) or Avg

(Average Power) measured in μW.

Table 2: Parameters in the output from the show system pluggable detail

command: (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 233

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PLUGGABLES AND CABLING COMMANDS

SHOW SYSTEM PLUGGABLE DIAGNOSTICS

show system pluggable diagnostics

Overview Different types of pluggable transceivers are supported in different models of

device. See your device’s Datasheet for more information about the models of

pluggables that your device supports.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show system pluggable [<port-list>] diagnostics

Mode User Exec and Privileged Exec

Usage Diagnostic monitoring features allow you to monitor real-time parameters of the

pluggable transceiver, such as optical output power, optical input power,

temperature, laser bias current, and transceiver supply voltage. Additionally, RX

LOS (Loss of Signal) is shown when the received optical level is below a preset

threshold. Monitor these parameters to check on the health of all transceivers,

selected transceivers or a specific transceiver installed in a device.

Examples To display detailed information about all pluggable transceivers installed on a

standalone device, use the command:

awplus# show system pluggable diagnostics

Output Figure 6-3: Example output from the show system pluggable diagnostics

command on a device

Parameter Description

<port-list> The ports to display information about. The port list can be:

• a switch port (e.g. port1.0.25)

• a continuous range of ports separated by a hyphen (e.g.

port1.0.27-1.0.28)

• a comma-separated list of ports and port ranges (e.g.

port1.0.25,port1.0.27-1.0.28)

awplus#show system pluggable diagnostics



Stack member 1



port1.0.27 Status Alarms Warnings

Reading Alarm Max Min Warning Max Min

Temp: (Degrees C) 29.300 - 78.000 -13.00 - 73.000 -8.000

Vcc: (Volts) 3.2424 - 3.8000 2.8000 - 3.5000 3.1000

Tx Bias: (mA) 10.688 - 30.880 0.880 - 24.880 4.880

Tx Power: (mW) 0.5417 - 1.1749 0.1995 - 0.9333 0.2512

Rx Power: (mW) - Low 1.2589 0.0490 Low 1.0000 0.0617

Rx LOS: Rx Down

613-50137-01 Rev A Command Reference for FS980M Series 234

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PLUGGABLES AND CABLING COMMANDS

SHOW SYSTEM PLUGGABLE DIAGNOSTICS

Commands

show system environment

show system pluggable

show system pluggable detail

Table 3: Parameters in the output from the show system pluggables

diagnostics command

Parameter Description

Temp (Degrees C) Shows the temperature inside the transceiver.

Vcc (Volts) Shows voltage supplied to the transceiver.

Tx Bias (mA) Shows current to the Laser Diode in the transceiver.

Tx Power (mW) Shows the amount of light transmitted from the transceiver.

Rx Power (mW) Shows the amount of light received in the transceiver.

Rx LOS Rx Loss of Signal. This indicates whether:

• light is being received (Rx Up) and therefore the link is up, or

• light is not being received (Rx Down) and therefore the link is

down

613-50137-01 Rev A Command Reference for FS980M Series 235

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PLUGGABLES AND CABLING COMMANDS

SHOW TEST CABLE-DIAGNOSTICS TDR

show test cable-diagnostics tdr

Overview Use this command to display the results of the last cable-diagnostics test that was

run using the TDR (Time Domain Reflectometer) on a fixed copper cable port.

The displayed status of the cable can be either:

•OK

•Open

• Short (within-pair)

• Short (across-pair)

• Error

Syntax show test cable-diagnostics tdr

Mode Privileged Exec

Examples To show the results of a cable-diagnostics test use the following command:

awplus# show test cable-diagnostics tdr

Output Figure 6-4: Example output from the show test cable-diagnostics tdr

command

Commands

clear test cable-diagnostics tdr

test cable-diagnostics tdr interface

Port Pair Length Status 

------------------------------------------------- 

1.0.1 A - OK 

B - OK 

C - OK 

D - OK

613-50137-01 Rev A Command Reference for FS980M Series 236

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PLUGGABLES AND CABLING COMMANDS

TEST CABLE-DIAGNOSTICS TDR INTERFACE

test cable-diagnostics tdr interface

Overview Use this command to apply the Cable Fault Locator’s cable-diagnostics tests to

twisted pair data cables for a selected port. The tests will detect either correct,

short circuit, or open, circuit terminations. For more information on running the

CFL, see the “Cable Fault Locator” Feature Overview and Configuration Guide.

The test can take several seconds to complete. See the related show command to

display the test results.

A new test can only be started if no other test is in progress. CFL cannot run on a

port that is currently supplying power via PoE.

The displayed status of the cable can be either, OK, Short (within-pair), or Open.

The “Open” or “Short” status is accompanied with the distance from the source

port to the incorrect termination.

Syntax test cable-diagnostics tdr interface <interface>

Mode Privileged Exec

Example To run a cable test on the cable inserted into port1.0.1 use the following command:

awplus# test cable-diagnostics tdr interface port1.0.1

You will receive the following message:

Link will go down while test is in progress. Continue? (y/n): y

Select y to continue.

awplus# y

You will then receive the following message:

Test started. This will take several seconds to complete. Use

"show test cable-diagnostics tdr" to print results.

Commands

clear test cable-diagnostics tdr

show test cable-diagnostics tdr

Parameter Description

cable-diagnostics The cable diagnostic tests.

tdr Time Domain Reflectometry.

interface Selects the interface to test.

<interface> Interface number of the port to be tested, e.g. port1.0.2.

613-50137-01 Rev A Command Reference for FS980M Series 237

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Logging Commands

Introduction

Overview This chapter provides an alphabetical reference of commands used to configure

logging.

Command List •“clear exception log” on page 239

•“clear log” on page 240

•“clear log buffered” on page 241

•“clear log permanent” on page 242

•“default log buffered” on page 243

•“default log console” on page 244

•“default log email” on page 245

•“default log host” on page 246

•“default log monitor” on page 247

•“default log permanent” on page 248

•“log buffered” on page 249

•“log buffered (filter)” on page 250

•“log buffered exclude” on page 253

•“log buffered size” on page 256

•“log console” on page 257

•“log console (filter)” on page 258

•“log console exclude” on page 261

•“log email” on page 264

•“log email (filter)” on page 265

•“log email exclude” on page 268

613-50137-01 Rev A Command Reference for FS980M Series 238

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

•“log email time” on page 271

•“log facility” on page 273

•“log host” on page 275

•“log host (filter)” on page 277

•“log host exclude” on page 280

•“log host source” on page 283

•“log host time” on page 284

•“log monitor (filter)” on page 286

•“log monitor exclude” on page 289

•“log permanent” on page 292

•“log permanent (filter)” on page 293

•“log permanent exclude” on page 296

•“log permanent size” on page 299

•“log-rate-limit nsm” on page 300

•“log trustpoint” on page 302

•“show counter log” on page 303

•“show exception log” on page 304

•“show log” on page 305

•“show log config” on page 307

•“show log permanent” on page 309

•“show running-config log” on page 311

613-50137-01 Rev A Command Reference for FS980M Series 239

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

CLEAR EXCEPTION LOG

clear exception log

Overview This command resets the contents of the exception log, but does not remove the

associated core files.

NOTE: When this command is used within a stacked environment, it will remove the

contents of the exception logs in all stack members.

Syntax clear exception log

Mode Privileged Exec

Example awplus# clear exception log

613-50137-01 Rev A Command Reference for FS980M Series 240

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

CLEAR LOG

clear log

Overview This command removes the contents of the buffered and permanent logs.

NOTE: When this command is used within a stacked environment, it will remove the

contents of the buffered and permanent logs in all stack members.

Syntax clear log

Mode Privileged Exec

Example To delete the contents of the buffered and permanent log use the command:

awplus# clear log

Commands

clear log buffered

clear log permanent

show log

613-50137-01 Rev A Command Reference for FS980M Series 241

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

CLEAR LOG BUFFERED

clear log buffered

Overview This command removes the contents of the buffered log.

NOTE: When this command is used within a stacked environment, it will remove the

contents of the buffered logs in all stack members.

Syntax clear log buffered

Mode Privileged Exec

Example To delete the contents of the buffered log use the following commands:

awplus# clear log buffered

Commands

default log buffered

log buffered

log buffered (filter)

log buffered size

log buffered exclude

show log

show log config

613-50137-01 Rev A Command Reference for FS980M Series 242

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

CLEAR LOG PERMANENT

clear log permanent

Overview This command removes the contents of the permanent log.

NOTE: When this command is used within a stacked environment, it will remove the

contents of the permanent logs in all stack members.

Syntax clear log permanent

Mode Privileged Exec

Example To delete the contents of the permanent log use the following commands:

awplus# clear log permanent

Commands

default log permanent

log permanent

log permanent (filter)

log permanent exclude

log permanent size

show log config

show log permanent

613-50137-01 Rev A Command Reference for FS980M Series 243

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

DEFAULT LOG BUFFERED

default log buffered

Overview This command restores the default settings for the buffered log stored in RAM. By

default the size of the buffered log is 50 kB and it accepts messages with the

severity level of “warnings” and above.

Syntax default log buffered

Default The buffered log is enabled by default.

Mode Global Configuration

Example To restore the buffered log to its default settings use the following commands:

awplus# configure terminal

awplus(config)# default log buffered

Commands

clear log buffered

log buffered

log buffered (filter)

log buffered size

log buffered exclude

show log

show log config

613-50137-01 Rev A Command Reference for FS980M Series 244

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

DEFAULT LOG CONSOLE

default log console

Overview This command restores the default settings for log messages sent to the terminal

when a log console command is issued. By default all messages are sent to the

console when a log console command is issued.

Syntax default log console

Mode Global Configuration

Example To restore the log console to its default settings use the following commands:

awplus# configure terminal

awplus(config)# default log console

Commands

log console

log console (filter)

log console exclude

show log config

613-50137-01 Rev A Command Reference for FS980M Series 245

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

DEFAULT LOG EMAIL

default log email

Overview This command restores the default settings for log messages sent to an email

address. By default no filters are defined for email addresses. Filters must be

defined before messages will be sent. This command also restores the remote

syslog server time offset value to local (no offset).

Syntax default log email <email-address>

Mode Global Configuration

Example To restore the default settings for log messages sent to the email address

admin@alliedtelesis.com use the following commands:

awplus# configure terminal

awplus(config)# default log email admin@alliedtelesis.com

Commands

log email

log email (filter)

log email exclude

log email time

show log config

Parameter Description

<email-address> The email address to send log messages to

613-50137-01 Rev A Command Reference for FS980M Series 246

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

DEFAULT LOG HOST

default log host

Overview This command restores the default settings for log sent to a remote syslog server.

By default no filters are defined for remote syslog servers. Filters must be defined

before messages will be sent. This command also restores the remote syslog server

time offset value to local (no offset).

Syntax default log host <ip-addr>

Mode Global Configuration

Example To restore the default settings for messages sent to the remote syslog server with

IP address 10.32.16.21 use the following commands:

awplus# configure terminal

awplus(config)# default log host 10.32.16.21

Commands

log host

log host (filter)

log host exclude

log host source

log host time

show log config

Parameter Description

<ip-addr>The IP address of a remote syslog server

613-50137-01 Rev A Command Reference for FS980M Series 247

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

DEFAULT LOG MONITOR

default log monitor

Overview This command restores the default settings for log messages sent to the terminal

when a terminal monitor command is used.

Syntax default log monitor

Default All messages are sent to the terminal when a terminal monitor command is used.

Mode Global Configuration

Example To restore the log monitor to its default settings use the following commands:

awplus# configure terminal

awplus(config)# default log monitor

Commands

log monitor (filter)

log monitor exclude

show log config

terminal monitor

613-50137-01 Rev A Command Reference for FS980M Series 248

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

DEFAULT LOG PERMANENT

default log permanent

Overview This command restores the default settings for the permanent log stored in NVS.

By default, the size of the permanent log is 50 kB and it accepts messages with the

severity level of warnings and above.

Syntax default log permanent

Default The permanent log is enabled by default.

Mode Global Configuration

Example To restore the permanent log to its default settings use the following commands:

awplus# configure terminal

awplus(config)# default log permanent

Commands

clear log permanent

log permanent

log permanent (filter)

log permanent exclude

log permanent size

show log config

show log permanent

613-50137-01 Rev A Command Reference for FS980M Series 249

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG BUFFERED

log buffered

Overview This command configures the device to store log messages in RAM. Messages

stored in RAM are not retained on the device over a restart. Once the buffered log

reaches its configured maximum allowable size old messages will be deleted to

make way for new ones.

Syntax log buffered

no log buffered

Default The buffered log is configured by default.

Mode Global Configuration

Examples To configured the device to store log messages in RAM use the following

commands:

awplus# configure terminal

awplus(config)# log buffered

To configure the device to not store log messages in a RAM buffer use the

following commands:

awplus# configure terminal

awplus(config)# no log buffered

Commands

clear log buffered

default log buffered

log buffered (filter)

log buffered size

log buffered exclude

show log

show log config

613-50137-01 Rev A Command Reference for FS980M Series 250

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG BUFFERED (FILTER)

log buffered (filter)

Overview Use this command to create a filter to select messages to be sent to the buffered

log. Selection can be based on the priority/ severity of the message, the program

that generated the message, the logging facility used, a sub-string within the

message or a combination of some or all of these.

The no variant of this command removes the corresponding filter, so that the

specified messages are no longer sent to the buffered log.

Syntax log buffered [level <level>] [program <program-name>] [facility

<facility>] [msgtext <text-string>]

no log buffered [level <level>] [program <program-name>]

[facility <facility>] [msgtext <text-string>]

Parameter Description

level Filter messages to the buffered log by severity level.

<level>The minimum severity of message to send to the buffered log. The level can be specified as

one of the following numbers or level names, where 0 is the highest severity and 7 is the

lowest severity:

0|emergencies System is unusable

1|alerts Action must be taken immediately

2|critical Critical conditions

3|errors Error conditions

4|warnings Warning conditions

5|notices Normal, but significant, conditions

6|informational Informational messages

7|debugging Debug-level messages

program Filter messages to the buffered log by program. Include messages from a specified program in

the buffered log.

<program-

name>

The name of a program to log messages from, either one of the following predefined program

names (not case-sensitive), or another program name (case-sensitive) that you find in the log

output:

rsvp Resource Reservation Protocol (RSVP)

dot1x IEEE 802.1X Port-Based Access Control

lacp Link Aggregation Control Protocol (LACP)

stp Spanning Tree Protocol (STP)

rstp Rapid Spanning Tree Protocol (RSTP)

mstp Multiple Spanning Tree Protocol (MSTP)

imi Integrated Management Interface (IMI)

613-50137-01 Rev A Command Reference for FS980M Series 251

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG BUFFERED (FILTER)

Default By default the buffered log has a filter to select messages whose severity level is

“notices (5)” or higher. This filter may be removed using the no variant of this

command.

Mode Global Configuration

Examples To add a filter to send all messages generated by EPSR that have a severity of

notices or higher to the buffered log, use the following commands:

awplus# configure terminal

awplus(config)# log buffered level notices program epsr

imish Integrated Management Interface Shell (IMISH)

epsr Ethernet Protection Switched Rings (EPSR)

rmon Remote Monitoring

loopprot Loop Protection

poe Power-inline (Power over Ethernet)

dhcpsn DHCP snooping (DHCPSN)

facility Filter messages to the buffered log by syslog facility.

<facility>Specify one of the following syslog facilities to include messages from in the buffered log:

kern Kernel messages

user Random user-level messages

mail Mail system

daemon System daemons

auth Security/authorization messages

syslog Messages generated internally by syslogd

lpr Line printer subsystem

news Network news subsystem

uucp UUCP subsystem

cron Clock daemon

authpriv Security/authorization messages (private)

ftp FTP daemon

msgtext Select messages containing a certain text string.

<text-

string>

A text string to match (maximum 128 characters). This is case sensitive, and must be the last

text on the command line.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 252

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG BUFFERED (FILTER)

To add a filter to send all messages containing the text “Bridging initialization” to

the buffered log, use the following commands:

awplus# configure terminal

awplus(config)# log buffered msgtext Bridging initialization

To remove a filter that sends all messages generated by EPSR that have a severity

of notices or higher to the buffered log, use the following commands:

awplus# configure terminal

awplus(config)# no log buffered level notices program epsr

To remove a filter that sends all messages containing the text “Bridging

initialization” to the buffered log, use the following commands:

awplus# configure terminal

awplus(config)# no log buffered msgtext Bridging initialization

Commands

clear log buffered

default log buffered

log buffered

log buffered size

log buffered exclude

show log

show log config

613-50137-01 Rev A Command Reference for FS980M Series 253

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG BUFFERED EXCLUDE

log buffered exclude

Overview Use this command to exclude specified log messages from the buffered log. You

can exclude messages on the basis of:

• the priority/severity of the message

• the program that generated the message

• the logging facility used

• a sub-string within the message, or

• a combination of some or all of these.

Use the no variant of this command to stop excluding the specified messages.

Syntax log buffered exclude [level <level>] [program <program-name>]

[facility <facility>] [msgtext <text-string>]

no log buffered exclude [level <level>] [program

<program-name>] [facility <facility>] [msgtext <text-string>]

Parameter Description

level Exclude messages of the specified severity level.

<level>The severity level to exclude. The level can be specified as one of the following numbers or

level names, where 0 is the highest severity and 7 is the lowest severity:

0|emergencies System is unusable

1|alerts Action must be taken immediately

2|critical Critical conditions

3|errors Error conditions

4|warnings Warning conditions

5|notices Normal, but significant, conditions

6|informational Informational messages

7|debugging Debug-level messages

program Exclude messages from a specified program.

<program-

name>

The name of a program. Either one of the following predefined program names (not

case-sensitive), or another program name (case-sensitive) that you find in the log output.

rsvp Resource Reservation Protocol (RSVP)

dot1x IEEE 802.1X Port-Based Access Control

lacp Link Aggregation Control Protocol (LACP)

stp Spanning Tree Protocol (STP)

rstp Rapid Spanning Tree Protocol (RSTP)

mstp Multiple Spanning Tree Protocol (MSTP)

613-50137-01 Rev A Command Reference for FS980M Series 254

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG BUFFERED EXCLUDE

Default No log messages are excluded

Mode Global configuration

Example To remove messages that contain the string “example of irrelevant message”, use

the following commands:

awplus# configure terminal

awplus(config)# log buffered exclude msgtext example of

irrelevant message

Commands

clear log buffered

default log buffered

imi Integrated Management Interface (IMI)

imish Integrated Management Interface Shell (IMISH)

epsr Ethernet Protection Switched Rings (EPSR)

rmon Remote Monitoring

loopprot Loop Protection

poe Power-inline (Power over Ethernet)

dhcpsn DHCP snooping (DHCPSN)

facility Exclude messages from a syslog facility.

<facility>Specify one of the following syslog facilities to exclude messages from:

kern Kernel messages

user Random user-level messages

mail Mail system

daemon System daemons

auth Security/authorization messages

syslog Messages generated internally by syslogd

lpr Line printer subsystem

news Network news subsystem

uucp UUCP subsystem

cron Clock daemon

authpriv Security/authorization messages (private)

ftp FTP daemon

msgtext Exclude messages containing a certain text string.

<text-

string>

A text string to match (maximum 128 characters). This is case sensitive, and must be the last

text on the command line.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 255

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG BUFFERED EXCLUDE

log buffered

log buffered (filter)

log buffered size

show log

show log config

613-50137-01 Rev A Command Reference for FS980M Series 256

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG BUFFERED SIZE

log buffered size

Overview This command configures the amount of memory that the buffered log is

permitted to use. Once this memory allocation has been filled old messages will be

deleted to make room for new messages.

Syntax log buffered size <50-250>

Mode Global Configuration

Example To allow the buffered log to use up to 100 kB of RAM use the following commands:

awplus# configure terminal

awplus(config)# log buffered size 100

Commands

clear log buffered

default log buffered

log buffered

log buffered (filter)

log buffered exclude

show log

show log config

Parameter Description

<50-250>Size of the RAM log in kilobytes

613-50137-01 Rev A Command Reference for FS980M Series 257

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG CONSOLE

log console

Overview This command configures the device to send log messages to consoles. The

console log is configured by default to send messages to the device’s main console

port.

Use the no variant of this command to configure the device not to send log

messages to consoles.

Syntax log console

no log console

Mode Global Configuration

Examples To configure the device to send log messages use the following commands:

awplus# configure terminal

awplus(config)# log console

To configure the device not to send log messages in all consoles use the following

commands:

awplus# configure terminal

awplus(config)# no log console

Commands

default log console

log console (filter)

log console exclude

show log config

613-50137-01 Rev A Command Reference for FS980M Series 258

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG CONSOLE (FILTER)

log console (filter)

Overview This command creates a filter to select messages to be sent to all consoles when

the log console command is given. Selection can be based on the priority/severity

of the message, the program that generated the message, the logging facility

used, a sub-string within the message or a combination of some or all of these.

Syntax log console [level <level>] [program <program-name>] [facility

<facility>] [msgtext <text-string>]

no log console [level <level>] [program <program-name>]

[facility <facility>] [msgtext <text-string>]

Parameter Description

level Filter messages by severity level.

<level>The minimum severity of message to send. The level can be specified as one of the following

numbers or level names, where 0 is the highest severity and 7 is the lowest severity:

0|emergencies System is unusable

1|alerts Action must be taken immediately

2|critical Critical conditions

3|errors Error conditions

4|warnings Warning conditions

5|notices Normal, but significant, conditions

6|informational Informational messages

7|debugging Debug-level messages

program Filter messages by program. Include messages from a specified program.

<program-

name>

The name of a program to log messages from, either one of the following predefined program

names (not case-sensitive), or another program name (case-sensitive) that you find in the log

output:

rsvp Resource Reservation Protocol (RSVP)

dot1x IEEE 802.1X Port-Based Access Control

lacp Link Aggregation Control Protocol (LACP)

stp Spanning Tree Protocol (STP)

rstp Rapid Spanning Tree Protocol (RSTP)

mstp Multiple Spanning Tree Protocol (MSTP)

imi Integrated Management Interface (IMI)

imish Integrated Management Interface Shell (IMISH)

epsr Ethernet Protection Switched Rings (EPSR)

rmon Remote Monitoring

613-50137-01 Rev A Command Reference for FS980M Series 259

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG CONSOLE (FILTER)

Default By default the console log has a filter to select messages whose severity level is

critical or higher. This filter may be removed using the no variant of this

command. This filter may be removed and replaced by filters that are more

selective.

Mode Global Configuration

Examples To create a filter to send all messages containing the text “Bridging initialization”

to console instances where the log console command has been entered, use the

following commands:

awplus# configure terminal

awplus(config)# log console msgtext "Bridging initialization"

To remove a filter that sends all messages generated by EPSR that have a severity

of notices or higher to consoles, use the following commands:

awplus# configure terminal

awplus(config)# no log console level notices program epsr

loopprot Loop Protection

poe Power-inline (Power over Ethernet)

dhcpsn DHCP snooping (DHCPSN)

facility Filter messages by syslog facility.

<facility>Specify one of the following syslog facilities to include messages from:

kern Kernel messages

user Random user-level messages

mail Mail system

daemon System daemons

auth Security/authorization messages

syslog Messages generated internally by syslogd

lpr Line printer subsystem

news Network news subsystem

uucp UUCP subsystem

cron Clock daemon

authpriv Security/authorization messages (private)

ftp FTP daemon

msgtext Select messages containing a certain text string.

<text-

string>

A text string to match (maximum 128 characters). This is case sensitive, and must be the last

text on the command line.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 260

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG CONSOLE (FILTER)

To remove a default filter that includes sending critical, alert and emergency

level messages to the console, use the following commands:

awplus# configure terminal

awplus(config)# no log console level critical

Commands

default log console

log console

log console exclude

show log config

613-50137-01 Rev A Command Reference for FS980M Series 261

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG CONSOLE EXCLUDE

log console exclude

Overview Use this command to prevent specified log messages from being sent to the

console, when console logging is turned on. You can exclude messages on the

basis of:

• the priority/severity of the message

• the program that generated the message

• the logging facility used

• a sub-string within the message, or

• a combination of some or all of these.

Use the no variant of this command to stop excluding the specified messages.

Syntax log console exclude [level <level>] [program <program-name>]

[facility <facility>] [msgtext <text-string>]

no log console exclude [level <level>] [program <program-name>]

[facility <facility>] [msgtext <text-string>]

Parameter Description

level Exclude messages of the specified severity level.

<level>The severity level to exclude. The level can be specified as one of the following numbers or

level names, where 0 is the highest severity and 7 is the lowest severity:

0|emergencies System is unusable

1|alerts Action must be taken immediately

2|critical Critical conditions

3|errors Error conditions

4|warnings Warning conditions

5|notices Normal, but significant, conditions

6|informational Informational messages

7|debugging Debug-level messages

program Exclude messages from a specified program.

<program-

name>

The name of a program. Either one of the following predefined program names (not

case-sensitive), or another program name (case-sensitive) that you find in the log output.

rsvp Resource Reservation Protocol (RSVP)

dot1x IEEE 802.1X Port-Based Access Control

lacp Link Aggregation Control Protocol (LACP)

stp Spanning Tree Protocol (STP)

rstp Rapid Spanning Tree Protocol (RSTP)

613-50137-01 Rev A Command Reference for FS980M Series 262

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG CONSOLE EXCLUDE

Default No log messages are excluded

Mode Global configuration

Example To remove messages that contain the string “example of irrelevant message”, use

the following commands:

awplus# configure terminal

awplus(config)# log console exclude msgtext example of

irrelevant message

Commands

default log console

mstp Multiple Spanning Tree Protocol (MSTP)

imi Integrated Management Interface (IMI)

imish Integrated Management Interface Shell (IMISH)

epsr Ethernet Protection Switched Rings (EPSR)

rmon Remote Monitoring

loopprot Loop Protection

poe Power-inline (Power over Ethernet)

dhcpsn DHCP snooping (DHCPSN)

facility Exclude messages from a syslog facility.

<facility>Specify one of the following syslog facilities to exclude messages from:

kern Kernel messages

user Random user-level messages

mail Mail system

daemon System daemons

auth Security/authorization messages

syslog Messages generated internally by syslogd

lpr Line printer subsystem

news Network news subsystem

uucp UUCP subsystem

cron Clock daemon

authpriv Security/authorization messages (private)

ftp FTP daemon

msgtext Exclude messages containing a certain text string.

<text-

string>

A text string to match (maximum 128 characters). This is case sensitive, and must be the last

text on the command line.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 263

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG CONSOLE EXCLUDE

log console

log console (filter)

show log config

613-50137-01 Rev A Command Reference for FS980M Series 264

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG EMAIL

log email

Overview This command configures the device to send log messages to an email address.

The email address is specified in this command.

Syntax log email <email-address>

Default By default no filters are defined for email log targets. Filters must be defined before

messages will be sent.

Mode Global Configuration

Example To have log messages emailed to the email address

admin@alliedtelesis.com use the following commands:

awplus# configure terminal

awplus(config)# log email admin@alliedtelesis.com

Commands

default log email

log email (filter)

log email exclude

log email time

show log config

Parameter Description

<email-address> The email address to send log messages to

613-50137-01 Rev A Command Reference for FS980M Series 265

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG EMAIL (FILTER)

log email (filter)

Overview This command creates a filter to select messages to be sent to an email address.

Selection can be based on the priority/ severity of the message, the program that

generated the message, the logging facility used, a sub-string within the message

or a combination of some or all of these.

The no variant of this command configures the device to no longer send log

messages to a specified email address. All configuration relating to this log target

will be removed.

Syntax log email <email-address> [level <level>] [program

<program-name>] [facility <facility>] [msgtext <text-string>]

no log email <email-address> [level <level>] [program

<program-name>] [facility <facility>] [msgtext <text-string>]

Parameter Description

<email-

address>

The email address to send logging messages to

level Filter messages by severity level.

<level>The minimum severity of message to send. The level can be specified as one of the following

numbers or level names, where 0 is the highest severity and 7 is the lowest severity:

0|emergencies System is unusable

1|alerts Action must be taken immediately

2|critical Critical conditions

3|errors Error conditions

4|warnings Warning conditions

5|notices Normal, but significant, conditions

6|informational Informational messages

7|debugging Debug-level messages

program Filter messages by program. Include messages from a specified program.

<program-

name>

The name of a program to log messages from, either one of the following predefined program

names (not case-sensitive), or another program name (case-sensitive) that you find in the log

output:

rsvp Resource Reservation Protocol (RSVP)

dot1x IEEE 802.1X Port-Based Access Control

lacp Link Aggregation Control Protocol (LACP)

stp Spanning Tree Protocol (STP)

rstp Rapid Spanning Tree Protocol (RSTP)

mstp Multiple Spanning Tree Protocol (MSTP)

613-50137-01 Rev A Command Reference for FS980M Series 266

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG EMAIL (FILTER)

Mode Global Configuration

Examples To create a filter to send all messages generated by EPSR that have a severity of

notices or higher to the email address admin@homebase.com, use the following

commands:

awplus# configure terminal

awplus(config)# log email admin@homebase.com level notices

program epsr

imi Integrated Management Interface (IMI)

imish Integrated Management Interface Shell (IMISH)

epsr Ethernet Protection Switched Rings (EPSR)

rmon Remote Monitoring

loopprot Loop Protection

poe Power-inline (Power over Ethernet)

dhcpsn DHCP snooping (DHCPSN)

facility Filter messages by syslog facility.

<facility>Specify one of the following syslog facilities to include messages from:

kern Kernel messages

user Random user-level messages

mail Mail system

daemon System daemons

auth Security/authorization messages

syslog Messages generated internally by syslogd

lpr Line printer subsystem

news Network news subsystem

uucp UUCP subsystem

cron Clock daemon

authpriv Security/authorization messages (private)

ftp FTP daemon

msgtext Select messages containing a certain text string.

<text-

string>

A text string to match (maximum 128 characters). This is case sensitive, and must be the last

text on the command line.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 267

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG EMAIL (FILTER)

To create a filter to send all messages containing the text “Bridging initialization”,

to the email address admin@homebase.com, use the following commands:

awplus# configure terminal

awplus(config)# log email admin@homebase.com msgtext "Bridging

initialization"

To create a filter to send messages with a severity level of informational and

above to the email address admin@alliedtelesis.com, use the following

commands:

awplus# configure terminal

awplus(config)# log email admin@alliedtelesis.com level

informational

To stop the device emailing log messages emailed to the email address

admin@alliedtelesis.com, use the following commands:

awplus# configure terminal

awplus(config)# no log email admin@homebase.com

To remove a filter that sends all messages generated by EPSR that have a severity

of notices or higher to the email address admin@homebase.com, use the

following commands:

awplus# configure terminal

awplus(config)# no log email admin@homebase.com level notices

program epsr

To remove a filter that sends messages with a severity level of informational and

above to the email address admin@alliedtelesis.com, use the following

commands:

awplus# configure terminal

awplus(config)# no log email admin@alliedtelesis.com level

informational

Commands

default log email

log email

log email exclude

log email time

show log config

613-50137-01 Rev A Command Reference for FS980M Series 268

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG EMAIL EXCLUDE

log email exclude

Overview Use this command to prevent specified log messages from being emailed, when

the device is configured to send log messages to an email address. You can

exclude messages on the basis of:

• the priority/severity of the message

• the program that generated the message

• the logging facility used

• a sub-string within the message, or

• a combination of some or all of these.

Use the no variant of this command to stop excluding the specified messages.

Syntax log email exclude [level <level>] [program <program-name>]

[facility <facility>] [msgtext <text-string>]

no log email exclude [level <level>] [program <program-name>]

[facility <facility>] [msgtext <text-string>]

Parameter Description

level Exclude messages of the specified severity level.

<level>The severity level to exclude. The level can be specified as one of the following numbers or

level names, where 0 is the highest severity and 7 is the lowest severity:

0|emergencies System is unusable

1|alerts Action must be taken immediately

2|critical Critical conditions

3|errors Error conditions

4|warnings Warning conditions

5|notices Normal, but significant, conditions

6|informational Informational messages

7|debugging Debug-level messages

program Exclude messages from a specified program.

<program-

name>

The name of a program. Either one of the following predefined program names (not

case-sensitive), or another program name (case-sensitive) that you find in the log output.

rsvp Resource Reservation Protocol (RSVP)

dot1x IEEE 802.1X Port-Based Access Control

lacp Link Aggregation Control Protocol (LACP)

stp Spanning Tree Protocol (STP)

rstp Rapid Spanning Tree Protocol (RSTP)

613-50137-01 Rev A Command Reference for FS980M Series 269

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG EMAIL EXCLUDE

Default No log messages are excluded

Mode Global configuration

Example To remove messages that contain the string “example of irrelevant message”, use

the following commands:

awplus# configure terminal

awplus(config)# log email exclude msgtext example of irrelevant

message

mstp Multiple Spanning Tree Protocol (MSTP)

imi Integrated Management Interface (IMI)

imish Integrated Management Interface Shell (IMISH)

epsr Ethernet Protection Switched Rings (EPSR)

rmon Remote Monitoring

loopprot Loop Protection

poe Power-inline (Power over Ethernet)

dhcpsn DHCP snooping (DHCPSN)

facility Exclude messages from a syslog facility.

<facility>Specify one of the following syslog facilities to exclude messages from:

kern Kernel messages

user Random user-level messages

mail Mail system

daemon System daemons

auth Security/authorization messages

syslog Messages generated internally by syslogd

lpr Line printer subsystem

news Network news subsystem

uucp UUCP subsystem

cron Clock daemon

authpriv Security/authorization messages (private)

ftp FTP daemon

msgtext Exclude messages containing a certain text string.

<text-

string>

A text string to match (maximum 128 characters). This is case sensitive, and must be the last

text on the command line.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 270

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG EMAIL EXCLUDE

Commands

default log email

log email

log email (filter)

log email time

show log config

613-50137-01 Rev A Command Reference for FS980M Series 271

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG EMAIL TIME

log email time

Overview This command configures the time used in messages sent to an email address. If

the syslog server is in a different time zone to your device then the time offset can

be configured using either the utc-offset parameter option keyword or the

local-offset parameter option keyword, where utc-offset is the time difference

from UTC (Universal Time, Coordinated) and local-offset is the difference from

local time.

Syntax log email <email-address> time {local|local-offset|utc-offset

{plus|minus}<0-24>}

Default The default is local time.

Mode Global Configuration

Usage Use the local option if the email recipient is in the same time zone as this device.

Messages will display the time as on the local device when the message was

generated.

Use the offset option if the email recipient is in a different time zone to this device.

Specify the time offset of the email recipient in hours. Messages will display the

time they were generated on this device but converted to the time zone of the

email recipient.

Parameter Description

<email-address> The email address to send log messages to

time Specify the time difference between the email recipient and the

device you are configuring.

local The device is in the same time zone as the email recipient

local-offset The device is in a different time zone to the email recipient. Use

the plus or minus keywords and specify the difference (offset)

from local time of the device to the email recipient in hours.

utc-offset The device is in a different time zone to the email recipient. Use

the plus or minus keywords and specify the difference (offset)

from UTC time of the device to the email recipient in hours.

plus Negative offset (difference) from the device to the email

recipient.

minus Positive offset (difference) from the device to the email

recipient.

<0-24> World Time zone offset in hours

613-50137-01 Rev A Command Reference for FS980M Series 272

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG EMAIL TIME

Examples To send messages to the email address test@home.com in the same time zone

as the device’s local time zone, use the following commands:

awplus# configure terminal

awplus(config)# log email admin@base.com time local 0

To send messages to the email address admin@base.com with the time

information converted to the time zone of the email recipient, which is 3 hours

ahead of the device’s local time zone, use the following commands:

awplus# configure terminal

awplus(config)# log email admin@base.com time local-offset plus

To send messages to the email address user@remote.com with the time

information converted to the time zone of the email recipient, which is 3 hours

behind the device’s UTC time zone, use the following commands:

awplus# configure terminal

awplus(config)# log email user@remote.com time utc-offset minus

Commands

default log email

log email

log email (filter)

log email exclude

show log config

613-50137-01 Rev A Command Reference for FS980M Series 273

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG FACILITY

log facility

Overview Use this command to specify an outgoing syslog facility. This determines where

the syslog server will store the log messages.

Use the no variant of this command to remove the facility.

Syntax log facility

{kern|user|mail|daemon|auth|syslog|lpr|news|uucp|cron|authpriv

|ftp|local0|local1|local2|local3|local4|local5|local6|local7}

no log facility

Default None (the outgoing syslog facility depends on the log message)

Mode Global Configuration

Parameter Description

kern Kernel messages

user User-level messages

mail Mail system

daemon System daemons

auth Security/authorization messages

syslog Messages generated internally by the syslog daemon

lpr Line printer subsystem

news Network news subsystem

uucp UNIX-to-UNIX Copy Program subsystem

cron Clock daemon

authpriv Security/authorization (private) messages

ftp FTP daemon

local0 Local use 0

local1 Local use 1

local2 Local use 2

local3 Local use 3

local4 Local use 4

local5 Local use 5

local6 Local use 6

local7 Local use 7

613-50137-01 Rev A Command Reference for FS980M Series 274

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG FACILITY

Example To specify a facility of local0, use the following commands:

awplus# configure terminal

awplus(config)# log facility local0

Commands

show log config

613-50137-01 Rev A Command Reference for FS980M Series 275

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG HOST

log host

Overview This command configures the device to send log messages to a remote syslog

server via UDP port 514. The IP address of the remote server must be specified. By

default no filters are defined for remote syslog servers. Filters must be defined

before messages will be sent.

Use the no variant of this command to stop sending log messages to the remote

syslog server.

Syntax log host <ipv4-addr>|<ipv6-addr> [secure]

no log host <ipv4-addr>|<ipv6-addr>

Mode Global Configuration

Usage Use the optional secure parameter to configure a secure syslog host. For secure

hosts, syslog over TLS is used to encrypt the logs. The certificate received from the

remote log server must have an issuer chain that terminates with the root CA

certificate for any of the trustpoints that are associated with the application.

The remote server may also request that a certificate is transmitted from the local

device. In this situation the first trustpoint added to the syslog application will be

transmitted to the remote server.

Examples To configure the device to send log messages to a remote secure syslog server with

IP address 10.32.16.99 use the following commands:

awplus# configure terminal

awplus(config)# log host 10.32.16.99 secure

To stop the device from sending log messages to the remote syslog server with IP

address 10.32.16.99 use the following commands:

awplus# configure terminal

awplus(config)# no log host 10.32.16.99

Commands

default log host

log host (filter)

log host exclude

log host source

Parameter Description

<ipv4-addr>Specify the source IPv4 address, in dotted decimal notation (A.B.C.D).

<ipv6-addr> Specify the source IPv6 address, in X:X::X:X notation.

secure Optional value to create a secure log destination

613-50137-01 Rev A Command Reference for FS980M Series 276

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG HOST

log host time

log trustpoint

show log config

613-50137-01 Rev A Command Reference for FS980M Series 277

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG HOST (FILTER)

log host (filter)

Overview This command creates a filter to select messages to be sent to a remote syslog

server. Selection can be based on the priority/severity of the message, the program

that generated the message, the logging facility used, a substring within the

message or a combination of some or all of these.

The no variant of this command configures the device to no longer send log

messages to a remote syslog server. The IP address of the syslog server must be

specified. All configuration relating to this log target will be removed.

Syntax log host <ip-addr> [level <level>] [program <program-name>]

[facility <facility>] [msgtext <text-string>]

no log host <ip-addr> [level <level>] [program <program-name>]

[facility <facility>] [msgtext <text-string>]

Parameter Description

<ip-addr> The IP address of a remote syslog server.

level Filter messages by severity level.

<level>The minimum severity of message to send. The level can be specified as one of the following

numbers or level names, where 0 is the highest severity and 7 is the lowest severity:

0|emergencies System is unusable

1|alerts Action must be taken immediately

2|critical Critical conditions

3|errors Error conditions

4|warnings Warning conditions

5|notices Normal, but significant, conditions

6|informational Informational messages

7|debugging Debug-level messages

program Filter messages by program. Include messages from a specified program.

<program-

name>

The name of a program to log messages from, either one of the following predefined program

names (not case-sensitive), or another program name (case-sensitive) that you find in the log

output:

rsvp Resource Reservation Protocol (RSVP)

dot1x IEEE 802.1X Port-Based Access Control

lacp Link Aggregation Control Protocol (LACP)

stp Spanning Tree Protocol (STP)

rstp Rapid Spanning Tree Protocol (RSTP)

mstp Multiple Spanning Tree Protocol (MSTP)

imi Integrated Management Interface (IMI)

613-50137-01 Rev A Command Reference for FS980M Series 278

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG HOST (FILTER)

Mode Global Configuration

Examples To create a filter to send all messages generated by EPSR that have a severity of

notices or higher to a remote syslog server with IP address 10.32.16.21, use the

following commands:

awplus# configure terminal

awplus(config)# log host 10.32.16.21 level notices program epsr

To create a filter to send all messages containing the text “Bridging initialization”,

to a remote syslog server with IP address 10.32.16.21, use the following

commands:

awplus# configure terminal

awplus(config)# log host 10.32.16.21 msgtext "Bridging

initialization"

imish Integrated Management Interface Shell (IMISH)

epsr Ethernet Protection Switched Rings (EPSR)

rmon Remote Monitoring

loopprot Loop Protection

poe Power-inline (Power over Ethernet)

dhcpsn DHCP snooping (DHCPSN)

facility Filter messages by syslog facility.

<facility>Specify one of the following syslog facilities to include messages from:

kern Kernel messages

user Random user-level messages

mail Mail system

daemon System daemons

auth Security/authorization messages

syslog Messages generated internally by syslogd

lpr Line printer subsystem

news Network news subsystem

uucp UUCP subsystem

cron Clock daemon

authpriv Security/authorization messages (private)

ftp FTP daemon

msgtext Select messages containing a certain text string.

<text-

string>

A text string to match (maximum 128 characters). This is case sensitive, and must be the last

text on the command line.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 279

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG HOST (FILTER)

To create a filter to send messages with a severity level of informational and

above to the syslog server with IP address 10.32.16.21, use the following

commands:

awplus# configure terminal

awplus(config)# log host 10.32.16.21 level informational

To remove a filter that sends all messages generated by EPSR that have a severity

of notices or higher to a remote syslog server with IP address 10.32.16.21, use the

following commands:

awplus# configure terminal

awplus(config)# no log host 10.32.16.21 level notices program

epsr

To remove a filter that sends all messages containing the text “Bridging

initialization”, to a remote syslog server with IP address 10.32.16.21, use the

following commands:

awplus# configure terminal

awplus(config)# no log host 10.32.16.21 msgtext "Bridging

initialization"

To remove a filter that sends messages with a severity level of informational and

above to the syslog server with IP address 10.32.16.21, use the following

commands:

awplusawpluls# configure terminal

awplus(config)# no log host 10.32.16.21 level informational

Commands

default log host

log host

log host exclude

log host source

log host time

show log config

613-50137-01 Rev A Command Reference for FS980M Series 280

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG HOST EXCLUDE

log host exclude

Overview Use this command to prevent specified log messages from being sent to the

remote syslog server, when log host is enabled. You can exclude messages on the

basis of:

• the priority/severity of the message

• the program that generated the message

• the logging facility used

• a sub-string within the message, or

• a combination of some or all of these.

Use the no variant of this command to stop excluding the specified messages.

Syntax log host exclude [level <level>] [program <program-name>]

[facility <facility>] [msgtext <text-string>]

no log host exclude [level <level>] [program <program-name>]

[facility <facility>] [msgtext <text-string>]

Parameter Description

level Exclude messages of the specified severity level.

<level>The severity level to exclude. The level can be specified as one of the following numbers or

level names, where 0 is the highest severity and 7 is the lowest severity:

0|emergencies System is unusable

1|alerts Action must be taken immediately

2|critical Critical conditions

3|errors Error conditions

4|warnings Warning conditions

5|notices Normal, but significant, conditions

6|informational Informational messages

7|debugging Debug-level messages

program Exclude messages from a specified program.

<program-

name>

The name of a program. Either one of the following predefined program names (not

case-sensitive), or another program name (case-sensitive) that you find in the log output.

rsvp Resource Reservation Protocol (RSVP)

dot1x IEEE 802.1X Port-Based Access Control

lacp Link Aggregation Control Protocol (LACP)

stp Spanning Tree Protocol (STP)

rstp Rapid Spanning Tree Protocol (RSTP)

613-50137-01 Rev A Command Reference for FS980M Series 281

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG HOST EXCLUDE

Default No log messages are excluded

Mode Global configuration

Example To remove messages that contain the string “example of irrelevant message”, use

the following commands:

awplus# configure terminal

awplus(config)# log host exclude msgtext example of irrelevant

message

Commands

default log host

mstp Multiple Spanning Tree Protocol (MSTP)

imi Integrated Management Interface (IMI)

imish Integrated Management Interface Shell (IMISH)

epsr Ethernet Protection Switched Rings (EPSR)

rmon Remote Monitoring

loopprot Loop Protection

poe Power-inline (Power over Ethernet)

dhcpsn DHCP snooping (DHCPSN)

facility Exclude messages from a syslog facility.

<facility>Specify one of the following syslog facilities to exclude messages from:

kern Kernel messages

user Random user-level messages

mail Mail system

daemon System daemons

auth Security/authorization messages

syslog Messages generated internally by syslogd

lpr Line printer subsystem

news Network news subsystem

uucp UUCP subsystem

cron Clock daemon

authpriv Security/authorization messages (private)

ftp FTP daemon

msgtext Exclude messages containing a certain text string.

<text-

string>

A text string to match (maximum 128 characters). This is case sensitive, and must be the last

text on the command line.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 282

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG HOST EXCLUDE

log host

log host (filter)

log host source

log host time

show log config

613-50137-01 Rev A Command Reference for FS980M Series 283

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG HOST SOURCE

log host source

Overview Use this command to specify a source interface or IP address for the device to send

syslog messages from. You can specify any one of an interface name, an IPv4

address or an IPv6 address.

This is useful if the device can reach the syslog server via multiple interfaces or

addresses and you want to control which interface/address the device uses.

Use the no variant of this command to stop specifying a source interface or

address.

Syntax log host source {<interface-name>|<ipv4-addr>|<ipv6-addr>}

no log host source

Default None (no source is configured)

Mode Global Configuration

Example To send syslog messages from 192.168.1.1, use the commands:

awplus# configure terminal

awplus(config)# log host source 192.168.1.1

Commands

default log host

log host

log host (filter)

log host exclude

log host time

show log config

Parameter Description

<interface-name> Specify the source interface name. You can enter a VLAN, eth

interface or loopback interface.

<ipv4-add> Specify the source IPv4 address, in dotted decimal notation

(A.B.C.D).

<ipv6-add> Specify the source IPv6 address, in X:X::X:X notation.

613-50137-01 Rev A Command Reference for FS980M Series 284

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG HOST TIME

log host time

Overview This command configures the time used in messages sent to a remote syslog

server. If the syslog server is in a different time zone to your device then the time

offset can be configured using either the utc-offset parameter option keyword or

the local-offset parameter option keyword, where utc-offset is the time

difference from UTC (Universal Time, Coordinated) and local-offset is the

difference from local time.

Syntax log host <email-address> time {local|local-offset|utc-offset

{plus|minus} <0-24>}

Default The default is local time.

Mode Global Configuration

Usage Use the local option if the remote syslog server is in the same time zone as the

device. Messages will display the time as on the local device when the message

was generated.

Use the offset option if the email recipient is in a different time zone to this device.

Specify the time offset of the remote syslog server in hours. Messages will display

the time they were generated on this device but converted to the time zone of the

remote syslog server.

Examples To send messages to the remote syslog server with the IP address 10.32.16.21

in the same time zone as the device’s local time zone, use the following

commands:

awplus# configure terminal

awplus(config)# log host 10.32.16.21 time local 0

Parameter Description

<email-address> The email address to send log messages to

time Specify the time difference between the email recipient and the

device you are configuring.

local The device is in the same time zone as the email recipient

local-offset The device is in a different time zone to the email recipient. Use

the plus or minus keywords and specify the difference (offset)

from local time of the device to the email recipient in hours.

utc-offset The device is in a different time zone to the email recipient. Use

the plus or minus keywords and specify the difference (offset)

from UTC time of the device to the email recipient in hours.

plus Negative offset (difference) from the device to the syslog server.

minus Positive offset (difference) from the device to the syslog server.

<0-24> World Time zone offset in hours

613-50137-01 Rev A Command Reference for FS980M Series 285

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG HOST TIME

To send messages to the remote syslog server with the IP address 10.32.16.12

with the time information converted to the time zone of the remote syslog server,

which is 3 hours ahead of the device’s local time zone, use the following

commands:

awplus# configure terminal

awplus(config)# log host 10.32.16.12 time local-offset plus 3

To send messages to the remote syslog server with the IP address 10.32.16.02

with the time information converted to the time zone of the email recipient, which

is 3 hours behind the device’s UTC time zone, use the following commands:

awplus# configure terminal

awplus(config)# log host 10.32.16.02 time utc-offset minus 3

Commands

default log host

log host

log host (filter)

log host exclude

log host source

show log config

613-50137-01 Rev A Command Reference for FS980M Series 286

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG MONITOR (FILTER)

log monitor (filter)

Overview This command creates a filter to select messages to be sent to the terminal when

the terminal monitor command is given. Selection can be based on the

priority/severity of the message, the program that generated the message, the

logging facility used, a sub-string within the message or a combination of some or

all of these.

Syntax log monitor [level <level>] [program <program-name>] [facility

<facility>] [msgtext <text-string>]

no log monitor [level <level>] [program <program-name>]

[facility <facility>] [msgtext <text-string>]

Parameter Description

level Filter messages by severity level.

<level>The minimum severity of message to send. The level can be specified as one of the following

numbers or level names, where 0 is the highest severity and 7 is the lowest severity:

0|emergencies System is unusable

1|alerts Action must be taken immediately

2|critical Critical conditions

3|errors Error conditions

4|warnings Warning conditions

5|notices Normal, but significant, conditions

6|informational Informational messages

7|debugging Debug-level messages

program Filter messages by program. Include messages from a specified program.

<program-

name>

The name of a program to log messages from, either one of the following predefined program

names (not case-sensitive), or another program name (case-sensitive) that you find in the log

output:

rsvp Resource Reservation Protocol (RSVP)

dot1x IEEE 802.1X Port-Based Access Control

lacp Link Aggregation Control Protocol (LACP)

stp Spanning Tree Protocol (STP)

rstp Rapid Spanning Tree Protocol (RSTP)

mstp Multiple Spanning Tree Protocol (MSTP)

imi Integrated Management Interface (IMI)

imish Integrated Management Interface Shell (IMISH)

epsr Ethernet Protection Switched Rings (EPSR)

613-50137-01 Rev A Command Reference for FS980M Series 287

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG MONITOR (FILTER)

Default By default there is a filter to select all messages. This filter may be removed and

replaced by filters that are more selective.

Mode Global Configuration

Examples To create a filter to send all messages that are generated by authentication and

have a severity of info or higher to terminal instances where the terminal monitor

command has been given, use the following commands:

awplus# configure terminal

awplus(config)# log monitor level info program auth

To remove a filter that sends all messages generated by EPSR that have a severity

of notices or higher to the terminal, use the following commands:

awplus# configure terminal

awplus(config)# no log monitor level notices program epsr

rmon Remote Monitoring

loopprot Loop Protection

poe Power-inline (Power over Ethernet)

dhcpsn DHCP snooping (DHCPSN)

facility Filter messages by syslog facility.

<facility>Specify one of the following syslog facilities to include messages from:

kern Kernel messages

user Random user-level messages

mail Mail system

daemon System daemons

auth Security/authorization messages

syslog Messages generated internally by syslogd

lpr Line printer subsystem

news Network news subsystem

uucp UUCP subsystem

cron Clock daemon

authpriv Security/authorization messages (private)

ftp FTP daemon

msgtext Select messages containing a certain text string.

<text-

string>

A text string to match (maximum 128 characters). This is case sensitive, and must be the last

text on the command line.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 288

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG MONITOR (FILTER)

To remove a default filter that includes sending everything to the terminal, use the

following commands:

awplus# configure terminal

awplus(config)# no log monitor level debugging

Commands

default log monitor

log monitor exclude

show log config

terminal monitor

613-50137-01 Rev A Command Reference for FS980M Series 289

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG MONITOR EXCLUDE

log monitor exclude

Overview Use this command to prevent specified log messages from being displayed on a

terminal, when terminal monitor is enabled. You can exclude messages on the

basis of:

• the priority/severity of the message

• the program that generated the message

• the logging facility used

• a sub-string within the message, or

• a combination of some or all of these.

Use the no variant of this command to stop excluding the specified messages.

Syntax log console exclude [level <level>] [program <program-name>]

[facility <facility>] [msgtext <text-string>]

no log console exclude [level <level>] [program <program-name>]

[facility <facility>] [msgtext <text-string>]

Parameter Description

level Exclude messages of the specified severity level.

<level>The severity level to exclude. The level can be specified as one of the following numbers or

level names, where 0 is the highest severity and 7 is the lowest severity:

0|emergencies System is unusable

1|alerts Action must be taken immediately

2|critical Critical conditions

3|errors Error conditions

4|warnings Warning conditions

5|notices Normal, but significant, conditions

6|informational Informational messages

7|debugging Debug-level messages

program Exclude messages from a specified program.

<program-

name>

The name of a program. Either one of the following predefined program names (not

case-sensitive), or another program name (case-sensitive) that you find in the log output.

rsvp Resource Reservation Protocol (RSVP)

dot1x IEEE 802.1X Port-Based Access Control

lacp Link Aggregation Control Protocol (LACP)

stp Spanning Tree Protocol (STP)

rstp Rapid Spanning Tree Protocol (RSTP)

613-50137-01 Rev A Command Reference for FS980M Series 290

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG MONITOR EXCLUDE

Default No log messages are excluded

Mode Global configuration

Example To remove messages that contain the string “example of irrelevant message”, use

the following commands:

awplus# configure terminal

awplus(config)# log monitor exclude msgtext example of

irrelevant message

Commands

default log monitor

mstp Multiple Spanning Tree Protocol (MSTP)

imi Integrated Management Interface (IMI)

imish Integrated Management Interface Shell (IMISH)

epsr Ethernet Protection Switched Rings (EPSR)

rmon Remote Monitoring

loopprot Loop Protection

poe Power-inline (Power over Ethernet)

dhcpsn DHCP snooping (DHCPSN)

facility Exclude messages from a syslog facility.

<facility>Specify one of the following syslog facilities to exclude messages from:

kern Kernel messages

user Random user-level messages

mail Mail system

daemon System daemons

auth Security/authorization messages

syslog Messages generated internally by syslogd

lpr Line printer subsystem

news Network news subsystem

uucp UUCP subsystem

cron Clock daemon

authpriv Security/authorization messages (private)

ftp FTP daemon

msgtext Exclude messages containing a certain text string.

<text-

string>

A text string to match (maximum 128 characters). This is case sensitive, and must be the last

text on the command line.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 291

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG MONITOR EXCLUDE

log monitor (filter)

show log config

terminal monitor

613-50137-01 Rev A Command Reference for FS980M Series 292

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG PERMANENT

log permanent

Overview This command configures the device to send permanent log messages to

non-volatile storage (NVS) on the device. The content of the permanent log is

retained over a reboot. Once the permanent log reaches its configured maximum

allowable size old messages will be deleted to make way for new messages.

The no variant of this command configures the device not to send any messages

to the permanent log. Log messages will not be retained over a restart.

Syntax log permanent

no log permanent

Mode Global Configuration

Examples To enable permanent logging use the following commands:

awplus# configure terminal

awplus(config)# log permanent

To disable permanent logging use the following commands:

awplus# configure terminal

awplus(config)# no log permanent

Commands

clear log permanent

default log permanent

log permanent (filter)

log permanent exclude

log permanent size

show log config

show log permanent

613-50137-01 Rev A Command Reference for FS980M Series 293

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG PERMANENT (FILTER)

log permanent (filter)

Overview This command creates a filter to select messages to be sent to the permanent log.

Selection can be based on the priority/ severity of the message, the program that

generated the message, the logging facility used, a sub-string within the message

or a combination of some or all of these.

The no variant of this command removes the corresponding filter, so that the

specified messages are no longer sent to the permanent log.

Syntax log permanent [level <level>] [program <program-name>]

[facility <facility>] [msgtext <text-string>]

no log permanent [level <level>] [program <program-name>]

[facility <facility>] [msgtext <text-string>]

Parameter Description

level Filter messages sent to the permanent log by severity level.

<level>The minimum severity of message to send. The level can be specified as one of the following

numbers or level names, where 0 is the highest severity and 7 is the lowest severity:

0|emergencies System is unusable

1|alerts Action must be taken immediately

2|critical Critical conditions

3|errors Error conditions

4|warnings Warning conditions

5|notices Normal, but significant, conditions

6|informational Informational messages

7|debugging Debug-level messages

program Filter messages by program. Include messages from a specified program.

<program-

name>

The name of a program to log messages from, either one of the following predefined program

names (not case-sensitive), or another program name (case-sensitive) that you find in the log

output:

rsvp Resource Reservation Protocol (RSVP)

dot1x IEEE 802.1X Port-Based Access Control

lacp Link Aggregation Control Protocol (LACP)

stp Spanning Tree Protocol (STP)

rstp Rapid Spanning Tree Protocol (RSTP)

mstp Multiple Spanning Tree Protocol (MSTP)

imi Integrated Management Interface (IMI)

imish Integrated Management Interface Shell (IMISH)

613-50137-01 Rev A Command Reference for FS980M Series 294

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG PERMANENT (FILTER)

Default By default the buffered log has a filter to select messages whose severity level is

notices (5) or higher. This filter may be removed using the no variant of this

command.

Mode Global Configuration

Examples To create a filter to send all messages generated by EPSR that have a severity of

notices or higher to the permanent log use the following commands:

awplus# configure terminal

awplus(config)# log permanent level notices program epsr

To create a filter to send all messages containing the text “Bridging

initialization”, to the permanent log use the following commands:

awplus# configure terminal

awplus(config)# log permanent msgtext Bridging initialization

epsr Ethernet Protection Switched Rings (EPSR)

rmon Remote Monitoring

loopprot Loop Protection

poe Power-inline (Power over Ethernet)

dhcpsn DHCP snooping (DHCPSN)

facility Filter messages by syslog facility.

<facility>Specify one of the following syslog facilities to include messages from:

kern Kernel messages

user Random user-level messages

mail Mail system

daemon System daemons

auth Security/authorization messages

syslog Messages generated internally by syslogd

lpr Line printer subsystem

news Network news subsystem

uucp UUCP subsystem

cron Clock daemon

authpriv Security/authorization messages (private)

ftp FTP daemon

msgtext Select messages containing a certain text string.

<text-

string>

A text string to match (maximum 128 characters). This is case sensitive, and must be the last

text on the command line.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 295

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG PERMANENT (FILTER)

Commands

clear log permanent

default log permanent

log permanent

log permanent exclude

log permanent size

show log config

show log permanent

613-50137-01 Rev A Command Reference for FS980M Series 296

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG PERMANENT EXCLUDE

log permanent exclude

Overview Use this command to prevent specified log messages from being sent to the

permanent log. You can exclude messages on the basis of:

• the priority/severity of the message

• the program that generated the message

• the logging facility used

• a sub-string within the message, or

• a combination of some or all of these.

Use the no variant of this command to stop excluding the specified messages.

Syntax log permanent exclude [level <level>] [program <program-name>]

[facility <facility>] [msgtext <text-string>]

no log permanent exclude [level <level>] [program

<program-name>] [facility <facility>] [msgtext <text-string>]

Parameter Description

level Exclude messages of the specified severity level.

<level>The severity level to exclude. The level can be specified as one of the following numbers or

level names, where 0 is the highest severity and 7 is the lowest severity:

0|emergencies System is unusable

1|alerts Action must be taken immediately

2|critical Critical conditions

3|errors Error conditions

4|warnings Warning conditions

5|notices Normal, but significant, conditions

6|informational Informational messages

7|debugging Debug-level messages

program Exclude messages from a specified program.

<program-

name>

The name of a program. Either one of the following predefined program names (not

case-sensitive), or another program name (case-sensitive) that you find in the log output.

rsvp Resource Reservation Protocol (RSVP)

dot1x IEEE 802.1X Port-Based Access Control

lacp Link Aggregation Control Protocol (LACP)

stp Spanning Tree Protocol (STP)

rstp Rapid Spanning Tree Protocol (RSTP)

mstp Multiple Spanning Tree Protocol (MSTP)

613-50137-01 Rev A Command Reference for FS980M Series 297

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG PERMANENT EXCLUDE

Default No log messages are excluded

Mode Global configuration

Example To remove messages that contain the string “example of irrelevant message”, use

the following commands:

awplus# configure terminal

awplus(config)# log permanent exclude msgtext example of

irrelevant message

Commands

clear log permanent

default log permanent

imi Integrated Management Interface (IMI)

imish Integrated Management Interface Shell (IMISH)

epsr Ethernet Protection Switched Rings (EPSR)

rmon Remote Monitoring

loopprot Loop Protection

poe Power-inline (Power over Ethernet)

dhcpsn DHCP snooping (DHCPSN)

facility Exclude messages from a syslog facility.

<facility>Specify one of the following syslog facilities to exclude messages from:

kern Kernel messages

user Random user-level messages

mail Mail system

daemon System daemons

auth Security/authorization messages

syslog Messages generated internally by syslogd

lpr Line printer subsystem

news Network news subsystem

uucp UUCP subsystem

cron Clock daemon

authpriv Security/authorization messages (private)

ftp FTP daemon

msgtext Exclude messages containing a certain text string.

<text-

string>

A text string to match (maximum 128 characters). This is case sensitive, and must be the last

text on the command line.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 298

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG PERMANENT EXCLUDE

log permanent

log permanent (filter)

log permanent size

show log config

show log permanent

613-50137-01 Rev A Command Reference for FS980M Series 299

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG PERMANENT SIZE

log permanent size

Overview This command configures the amount of memory that the permanent log is

permitted to use. Once this memory allocation has been filled old messages will be

deleted to make room for new messages.

Syntax log permanent size <50-250>

Mode Global Configuration

Example To allow the permanent log to use up to 100 kB of NVS use the following

commands:

awplus# configure terminal

awplus(config)# log permanent size 100

Commands

clear log permanent

default log permanent

log permanent

log permanent (filter)

log permanent exclude

show log config

show log permanent

Parameter Description

<50-250>Size of the permanent log in kilobytes

613-50137-01 Rev A Command Reference for FS980M Series 300

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG-RATE-LIMIT NSM

log-rate-limit nsm

Overview This command limits the number of log messages generated by the device for a

given interval.

Use the no variant of this command to revert to the default number of log

messages generated by the device of up to 200 log messages per second.

Syntax log-rate-limit nsm messages <message-limit> interval

<time-interval>

no log-rate-limit nsm

Default By default, the device will allow 200 log messages to be generated per second.

Mode Global Configuration

Usage Previously, if the device received a continuous stream of IGMP packets with errors,

such as when a packet storm occurs because of a network loop, then the device

generates a lot of log messages using more and more memory, which may

ultimately cause the device to shutdown. This log rate limiting feature constrains

the rate that log messages are generated by the device.

Note that if within the given time interval, the number of log messages exceeds the

limit, then any excess log messages are discarded. At the end of the time interval,

a single log message is generated indicating that log messages were discarded

due to the log rate limit being exceeded.

Thus if the expectation is that there will be a lot of discarded log messages due to

log rate limiting, then it is advisable to set the time interval to no less than 100,

which means that there would only be one log message, indicating log excessive

log messages have been discarded.

Examples To limit the device to generate up to 300 log messages per second, use the

following commands:

awplus# configure terminal

awplus(config)# log-rate-limit nsm messages 300 interval 100

Parameter Description

<message-limit><1-65535>

The number of log messages generated by the device.

<time-interval><0-65535>

The time period for log message generation in 1/100 seconds.

If an interval of 0 is specified then no log message rate limiting

is applied.

613-50137-01 Rev A Command Reference for FS980M Series 301

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG-RATE-LIMIT NSM

To return the device the default setting, to generate up to 200 log messages per

second, use the following commands:

awplus# configure terminal

awplus(config)# no log-rate-limit nsm

613-50137-01 Rev A Command Reference for FS980M Series 302

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

LOG TRUSTPOINT

log trustpoint

Overview This command adds one or more trustpoints to be used with the syslog

application. Multiple trustpoints may be specified, or the command may be

executed multiple times, to add multiple trustpoints to the application.

The no version of this command removes one or more trustpoints from the list of

trustpoints associated with the application.

Syntax log trustpoint [<trustpoint-list>]

no log trustpoint [<trustpoint-list>]

Default No trustpoints are created by default.

Mode Global Configuration

Usage The device certificate associated with first trustpoint added to the application will

be transmitted to remote servers. The certificate received from the remote server

must have an issuer chain that terminates with the root CA certificate for any of the

trustpoints that are associated with the application.

If no trustpoints are specified in the command, the trustpoint list will be

unchanged.

If no log trustpoint is issued without specifying any trustpoints, then all

trustpoints will be disassociated from the application.

Example You can add multiple trustpoints by executing the command multiple times:

awplus# configure terminal

awplus(config)# log trustpoint trustpoint_1

awplus(config)# log trustpoint trustpoint_2

Alternatively, add multiple trustpoints with a single command:

awplus(config)# log trustpoint trustpoint_2 trustpoint_3

Disassociate all trustpoints from the syslog application using the command:

awplus(config)# log trustpoint trustpoint_2 trustpoint_3

Commands

log host

show log config

Parameter Description

<trustpoint-list> Specify one or more trustpoints to be added or deleted.

613-50137-01 Rev A Command Reference for FS980M Series 303

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

SHOW COUNTER LOG

show counter log

Overview This command displays log counter information.

Syntax show counter log

Mode User Exec and Privileged Exec

Example To display the log counter information, use the command:

awplus# show counter log

Output Figure 7-1: Example output from the show counter log command

Commands

show log config

Log counters

Total Received ......... 2328

Total Received P0 ......... 0

Total Received P1 ......... 0

Total Received P2 ......... 1

Total Received P3 ......... 9

Total Received P4 ......... 32

Total Received P5 ......... 312

Total Received P6 ......... 1602

Total Received P7 ......... 372

Table 1: Parameters in output of the show counter log command

Parameter Description

Total Received Total number of messages received by the log

Total Received P0 Total number of Priority 0 (Emergency) messages

received

Total Received P1 Total number of Priority 1 (Alert) messages received

Total Received P2 Total number of Priority 2 (Critical) messages received

Total Received P3 Total number of Priority 3 (Error) messages received

Total Received P4 Total number of Priority 4 (Warning) messages received

Total Received P5 Total number of Priority 5 (Notice) messages received

Total Received P6 Total number of Priority 6 (Info) messages received

Total Received P7 Total number of Priority 7 (Debug) messages received

613-50137-01 Rev A Command Reference for FS980M Series 304

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

SHOW EXCEPTION LOG

show exception log

Overview This command displays the contents of the exception log.

Syntax show exception log

Mode User Exec and Privileged Exec

Example To display the exception log, use the command:

awplus# show exception log

613-50137-01 Rev A Command Reference for FS980M Series 305

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

SHOW LOG

show log

Overview This command displays the contents of the buffered log.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show log [tail [<10-250>]]

Default By default the entire contents of the buffered log is displayed.

Mode User Exec, Privileged Exec and Global Configuration

Usage If the optional tail parameter is specified only the latest 10 messages in the

buffered log are displayed. A numerical value can be specified after the tail

parameter to select how many of the latest messages should be displayed.

The show log command is only available to users at privilege level 7 and above. To

set a user’s privilege level, use the command:

awplus(config)# username <name> privilege <1-15>

Examples To display the contents of the buffered log use the command:

awplus# show log

To display the 10 latest entries in the buffered log use the command:

awplus# show log tail 10

Parameter Description

tail Display only the latest log entries.

<10-250>Specify the number of log entries to display.

613-50137-01 Rev A Command Reference for FS980M Series 306

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

SHOW LOG

Output Figure 7-2: Example output from the show log command

Commands

clear log buffered

default log buffered

log buffered

log buffered (filter)

log buffered size

log buffered exclude

show log config

awplus#show log



<date> <time> <facility>.<severity> <program[<pid>]>: <message>

-------------------------------------------------------------------------

2016 Oct 19 02:11:28 daemon.warning awplus-1 rpc.mountd[1102]: /flash and /nvs have

same filehandle for 192.168.255.0/27, using first

2016 Oct 19 02:11:28 local6.crit awplus-1 Pluggable[404]: Pluggable AT-StackXS/1.0

inserted into port1.0.27

2016 Oct 19 02:11:28 local6.crit awplus-1 Pluggable[404]: Pluggable AT-StackXS/1.0

inserted into port1.0.28

2016 Oct 19 02:11:29 local6.notice awplus-1 VCS[509]: Link up event on stack link

1.0.1

2016 Oct 19 02:11:29 local6.notice awplus-1 VCS[509]: Link up event on stack link

1.0.2

2016 Oct 19 02:11:30 user.crit awplus-1 VCS[509]: Member 2 (0030.abf3.428b) has

joined the stack

2016 Oct 19 02:11:30 user.notice awplus-1 VCS[509]: Link between Member 1 and Member

2 is up

2016 Oct 19 02:11:32 user.crit awplus-1 VCS[509]: Member 1 (0030.abf3.41e5) has

become the Active Master

2016 Oct 19 02:11:32 local6.alert awplus-2 VCS[509]: stack member has booted from

non-default location, SW version auto synchronization cannot be supported.



...

613-50137-01 Rev A Command Reference for FS980M Series 307

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

SHOW LOG CONFIG

show log config

Overview This command displays information about the logging system. This includes the

configuration of the various log destinations, buffered, permanent, syslog servers

(hosts) and email addresses. This also displays the latest status information for

each of these destinations.

Syntax show log config

Mode User Exec, Privileged Exec and Global Configuration

Example To display the logging configuration use the command:

awplus# show log config

Output Figure 7-3: Example output from the show log config command

Facility: default



PKI trustpoints: example_trustpoint



Buffered log:

Status ......... enabled

Maximum size ... 100kb

Filters:

*1 Level ........ notices

Program ...... any

Facility ..... any

Message text . any

2 Level ........ informational

Program ...... auth

Facility ..... daemon

Message text . any

Statistics ..... 1327 messages received, 821 accepted by filter (2016 Oct 11 

10:36:16)

Permanent log:

Status ......... enabled

Maximum size ... 60kb

Filters:

1 Level ........ error

Program ...... any

Facility ..... any

Message text . any

*2 Level ........ warnings

Program ...... dhcp

Facility ..... any

Message text . "pool exhausted"

Statistics ..... 1327 messages received, 12 accepted by filter (2016 Oct 11 

10:36:16)

613-50137-01 Rev A Command Reference for FS980M Series 308

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

SHOW LOG CONFIG

In the above example the ’*’ next to filter 1 in the buffered log configuration

indicates that this is the default filter. The permanent log has had its default filter

removed, so none of the filters are marked with “*’.

NOTE: Terminal log and console log cannot be set at the same time. If console logging

is enabled then the terminal logging is turned off.

Commands

show counter log

show log

show log permanent

Host 10.32.16.21:

Time offset .... +2:00

Offset type .... UTC

Source ......... -

Secured ........ enabled

Filters:

1 Level ........ critical

Program ...... any

Facility ..... any

Message text . any

Statistics ..... 1327 messages received, 1 accepted by filter (2016 Oct 11 

10:36:16)

Email admin@alliedtelesis.com:

Time offset .... +0:00

Offset type .... Local

Filters:

1 Level ........ emergencies

Program ...... any

Facility ..... any

Message text . any

Statistics ..... 1327 messages received, 0 accepted by filter (2016 Oct 11 

10:36:16)

...

613-50137-01 Rev A Command Reference for FS980M Series 309

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

SHOW LOG PERMANENT

show log permanent

Overview This command displays the contents of the permanent log.

Syntax show log permanent [tail [<10-250>]]

show log permanent [<stack-ID>] [tail [<10-250>]]

Default If the optional tail parameter is specified only the latest 10 messages in the

permanent log are displayed. A numerical value can be specified after the tail

parameter to select how many of the latest messages should be displayed.

Mode User Exec, Privileged Exec and Global Configuration

Example To display the permanent log, use the command:

awplus# show log permanent

Example To display the permanent log of stack member 2, use the command:

awplus# show log permanent 2

Output Figure 7-4: Example output from the show log permanent command

Commands

clear log permanent

default log permanent

log permanent

Parameter Description

<stack-ID> Stack member number, from 1 to 8.

tail Display only the latest log entries.

<10-250>Specify the number of log entries to display.

awplus#show log permanent



<date> <time> <facility>.<severity> <program[<pid>]>: <message>

-------------------------------------------------------------------------

2016 Feb 16 02:20:40 kern.err s_src@awplus kernel: Last message 'RTNL: assertion

fail' repeated 11 times, suppressed by syslog-ng on awplus

2016 Feb 16 02:52:38 local6.crit awplus Pluggable[428]: Pluggable AT-SP10SR inserted

into port1.0.5

2016 Feb 16 02:52:38 local6.crit awplus Pluggable[428]: Pluggable AT-SP10SR inserted

into port1.0.6

2016 Feb 16 02:52:38 local6.crit awplus Pluggable[428]: Pluggable AT-SP10SR inserted

into port1.0.7

2016 Feb 16 02:52:39 local6.crit awplus Pluggable[428]: Pluggable AT-SP10SR inserted

into port1.0.8

2016 Feb 16 02:52:39 local6.crit awplus Pluggable[428]: Pluggable AT-SP10SR inserted

into port1.0.9

613-50137-01 Rev A Command Reference for FS980M Series 310

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

SHOW LOG PERMANENT

log permanent (filter)

log permanent exclude

log permanent size

show log config

613-50137-01 Rev A Command Reference for FS980M Series 311

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LOGGING COMMANDS

SHOW RUNNING-CONFIG LOG

show running-config log

Overview This command displays the current running configuration of the Log utility.

Syntax show running-config log

Mode Privileged Exec and Global Configuration

Example To display the current configuration of the log utility, use the command:

awplus# show running-config log

Commands

show log

show log config

613-50137-01 Rev A Command Reference for FS980M Series 312

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Scripting

Commands

Introduction

Overview This chapter provides commands used for command scripts.

Command List •“activate” on page 313

•“echo” on page 314

•“wait” on page 315

613-50137-01 Rev A Command Reference for FS980M Series 313

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SCRIPTING COMMANDS

ACTIVATE

activate

Overview This command activates a script file.

Syntax activate [background] <script>

Mode Privileged Exec

Usage When a script is activated, the privilege level is set to 1 enabling User Exec

commands to run in the script. If you need to run Privileged Exec commands in

your script you need to add an enable (Privileged Exec mode) command to the

start of your script. If you need to run Global Configuration commands in your

script you need to add a configure terminal command after the enable command

at the start of your script.

The activate command executes the script in a new shell. A terminal length shell

command, such as terminal length 0 may also be required to disable a delay that

would pause the display.

A script must be a text file with a filename extension of either . sh or . scp only for

the AlliedWare Plus™ CLI to activate the script file. The . sh filename extension

indicates the file is an ASH script, and the . scp filename extension indicates the file

is an AlliedWare Plus™ script.

Examples To activate a command script to run as a background process, use the command:

awplus# activate background test.scp

Commands

configure terminal

echo

enable (Privileged Exec mode)

wait

Parameter Description

background Activate a script to run in the background. A process that is running in

the background will operate as a separate task, and will not interrupt

foreground processing. Generally, we recommend running short,

interactive scripts in the foreground and longer scripts in the

background. The default is to run the script in the foreground.

consisting of commands documented in this software reference.

Note that you must use either a . scp or a . sh filename extension for a

valid script text file, as described below in the usage section for this

command.

613-50137-01 Rev A Command Reference for FS980M Series 314

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SCRIPTING COMMANDS

ECHO

echo

Overview This command echoes a string to the terminal, followed by a blank line.

Syntax echo <line>

Mode User Exec and Privileged Exec

Usage This command may be useful in CLI scripts, to make the script print user-visible

comments.

Example To echo the string Hello World to the console, use the command:

awplus# echo Hello World

Output

Commands

activate

wait

Parameter Description

<line>The string to echo

Hello World

613-50137-01 Rev A Command Reference for FS980M Series 315

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SCRIPTING COMMANDS

WAIT

wait

Overview This command pauses execution of the active script for the specified period of

time.

Syntax wait <delay>

Default No wait delay is specified by default to pause script execution.

Mode Privileged Exec (when executed from a script not directly from the command line)

Usage Use this command to pause script execution in an .scp (AlliedWare Plus™ script) or

an .sh (ASH script) file executed by the activate command. The script must contain

an enable command, because the wait command is only executed in the

Privileged Exec mode.

Example See an .scp script file extract below that will show port counters for interface

port1.0.1 over a 10 second interval:

Commands

activate

echo

enable (Privileged Exec mode)

Parameter Description

<delay><1-65335> Specify the time delay in seconds

enable



show interface port1.0.1



wait 10



show interface port1.0.1

613-50137-01 Rev A Command Reference for FS980M Series 316

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Interface

Commands

Introduction

Overview This chapter provides an alphabetical reference of commands used to configure

and display interfaces.

Command List •“description (interface)” on page 317

•“interface (to configure)” on page 318

•“mtu” on page 320

•“show interface” on page 322

•“show interface brief” on page 325

•“show interface memory” on page 326

•“show interface status” on page 328

•“shutdown” on page 330

613-50137-01 Rev A Command Reference for FS980M Series 317

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE COMMANDS

DESCRIPTION (INTERFACE)

description (interface)

Overview Use this command to add a description to a specific port or interface.

Syntax description <description>

Mode Interface Configuration

Example The following example uses this command to describe the device that a switch

port is connected to.

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# description Boardroom PC

Parameter Description

<description>Text describing the specific interface.

613-50137-01 Rev A Command Reference for FS980M Series 318

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE COMMANDS

INTERFACE (TO CONFIGURE)

interface (to configure)

Overview Use this command to select one or more interfaces to configure.

Syntax interface <interface-list>

interface lo

Usage A local loopback interface is one that is always available for higher layer protocols

to use and advertise to the network. Although a local loopback interface is

assigned an IP address, it does not have the usual requirement of connecting to a

lower layer physical entity. This lack of physical attachment creates the perception

of a local loopback interface always being accessible via the network.

Local loopback interfaces can be utilized by a number of protocols for various

purposes. They can be used to improve access to the device and also increase its

reliability, security, scalability and protection. In addition, local loopback interfaces

can add flexibility and simplify management, information gathering and filtering.

One example of this increased reliability is for OSPF to advertise a local loopback

interface as an interface-route into the network irrespective of the physical links

that may be “up” or “down” at the time. This provides a higher probability that the

routing traffic will be received and subsequently forwarded.

Mode Global Configuration

Example The following example shows how to enter Interface mode to configure vlan1.

Note how the prompt changes.

awplus# configure terminal

awplus(config)# interface vlan1

awplus(config-if)#

Parameter Description

<interface-list>The interfaces or ports to configure.

An interface-list can be:

• an interface such as a VLAN (e.g. vlan2), a switch port (e.g.

port1.0.6), a static channel group (e.g. sa2) or a

dynamic (LACP) channel group (e.g. po2)

• a continuous range of interfaces, ports, static channel

groups or dynamic (LACP) channel groups separated by a

hyphen; e.g. vlan2-8, or port1.0.1-1.0.6, or

sa1-2, or po1-2

• a comma-separated list of the above; e.g.

port1.0.1,port1.0.4-1.0.6. Do not mix interface

types in a list

The specified interfaces must exist.

lo The local loopback interface.

613-50137-01 Rev A Command Reference for FS980M Series 319

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE COMMANDS

INTERFACE (TO CONFIGURE)

The following example shows how to enter Interface mode to configure the local

loopback interface.

awplus# configure terminal

awplus(config)# interface lo

awplus(config-if)#

Commands

ip address (IP Addressing and Protocol)

show interface

show interface brief

613-50137-01 Rev A Command Reference for FS980M Series 320

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE COMMANDS

MTU

mtu

Overview Use this command to set the Maximum Transmission Unit (MTU) size for VLANs,

where MTU is the maximum packet size that VLANs can transmit. The MTU size

setting is applied to both IPv4 and IPv6 packet transmission.

Use the no variant of this command to remove a previously specified Maximum

Transmission Unit (MTU) size for VLANs, and restore the default MTU size (1500

bytes) for VLANs.

Syntax mtu <68-1582>

no mtu

Default The default MTU size is 1500 bytes for VLAN interfaces.

Mode Interface Configuration for VLAN interfaces.

Usage If a device receives an IPv4 packet for Layer 3 switching to another VLAN with an

MTU size smaller than the packet size, and if the packet has the ‘don’t fragment’

bit set, then the device will send an ICMP ‘destination unreachable’ (3) packet

type and a ‘fragmentation needed and DF set’ (4) code back to the source. For

IPv6 packets bigger than the MTU size of the transmitting VLAN interface, an ICMP

‘packet too big’ (ICMP type 2 code 0) message is sent to the source.

Note that show interface output will only show MTU size for VLAN interfaces.

Examples To configure an MTU size of 1500 bytes on interface vlan2, use the commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# mtu 1500

To configure an MTU size of 1500 bytes on interfaces vlan2 to vlan4, use the

commands:

awplus# configure terminal

awplus(config)# interface vlan2-vlan4

awplus(config-if)# mtu 1500

To restore the MTU size to the default MTU size of 1500 bytes on vlan2, use the

commands

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# no mtu

To restore the MTU size to the default MTU size of 1500 bytes on vlan2 and

vlan4, use the commands

awplus# configure terminal

awplus(config)# interface vlan2-vlan4

awplus(config-if)# no mtu

613-50137-01 Rev A Command Reference for FS980M Series 321

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE COMMANDS

MTU

Commands

show interface

613-50137-01 Rev A Command Reference for FS980M Series 322

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE COMMANDS

SHOW INTERFACE

show interface

Overview Use this command to display interface configuration and status.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show interface [<interface-list>]

show interface lo

Mode User Exec and Privileged Exec

Usage Note that the output displayed with this command will show MTU (Maximum

Transmission Unit) size for VLAN interfaces, and MRU (Maximum Received Unit)

size for switch ports.

Example To display configuration and status information for all interfaces, use the

command:

awplus# show interface

Parameter Description

<interface-list>The interfaces or ports to configure. An interface-list can be:

• an interface such as a VLAN (e.g. vlan2), a switch port (e.g.

port1.0.6), a static channel group (e.g. sa2) or a

dynamic (LACP) channel group (e.g. po2)

• a continuous range of interfaces, ports, static channel

groups or dynamic (LACP) channel groups separated by a

hyphen; e.g. vlan2-8, or port1.0.1-1.0.6, or sa1-2,

or po1-2

• a comma-separated list of the above; e.g.

port1.0.1,port1.0.4-1.0.6. Do not mix interface

types in a list

The specified interfaces must exist.

lo The local loopback interface.

613-50137-01 Rev A Command Reference for FS980M Series 323

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE COMMANDS

SHOW INTERFACE

Figure 9-1: Example output from the show interface command

To display configuration and status information for interface lo, use the

command:

awplus# show interface lo

Figure 9-2: Example output from the show interface lo command

To display configuration and status information for interfaces vlan1 and vlan2,

use the command:

awplus# show interface vlan1,vlan2

awplus#show interface

Interface port1.0.1

Scope: both

Link is DOWN, administrative state is UP

Thrash-limiting

Status Not Detected, Action learn-disable, Timeout 1(s)

Hardware is Ethernet, address is eccd.6dff.d67d

index 5001 metric 1 mru 1500

configured duplex auto, configured speed auto, configured polarity auto

<UP,BROADCAST,MULTICAST>

SNMP link-status traps: Disabled

input packets 0, bytes 0, dropped 0, multicast packets 0

output packets 0, bytes 0, multicast packets 0 broadcast packets 0

Time since last state change: 0 days 01:37:41

...

awplus#show interface lo

Interface lo

Scope: both

Link is UP, administrative state is UP

Hardware is Loopback

index 1 metric 1

<UP,LOOPBACK,RUNNING>

SNMP link-status traps: Disabled

input packets 0, bytes 0, dropped 0, multicast packets 0

output packets 0, bytes 0, multicast packets 0 broadcast packets 0

Time since last state change: 69 days 01:28:47

613-50137-01 Rev A Command Reference for FS980M Series 324

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE COMMANDS

SHOW INTERFACE

Figure 9-3: Example output from the show interface vlan1,vlan2 command

Commands

mtu

show interface brief



awplus#show interface vlan1,vlan2

Interface vlan1

Scope: both

Link is UP, administrative state is UP

Hardware is VLAN, address is 0015.77e9.5c50

IPv4 address 192.168.1.1/24 broadcast 192.168.1.255

index 201 metric 1 mtu 1500

arp ageing timeout 300

<UP,BROADCAST,RUNNING,MULTICAST>

SNMP link-status traps: Disabled

Bandwidth 1g

input packets 295606, bytes 56993106, dropped 5, multicast packets 156

output packets 299172, bytes 67379392, multicast packets 0 broadcast packets 0

Time since last state change: 0 days 14:22:39



Interface vlan2

Scope: both

Link is DOWN, administrative state is UP

Hardware is VLAN, address is 0015.77e9.5c50

IPv4 address 192.168.2.1/24 broadcast 192.168.2.255

Description: ip_phone_vlan

index 202 metric 1 mtu 1500

arp ageing timeout 300

<UP,BROADCAST,MULTICAST>

SNMP link-status traps: Disabled

Bandwidth 1g

input packets 0, bytes 0, dropped 0, multicast packets 0

output packets 90, bytes 4244, multicast packets 0 broadcast packets 0

Time since last state change: 0 days 14:22:39

613-50137-01 Rev A Command Reference for FS980M Series 325

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE COMMANDS

SHOW INTERFACE BRIEF

show interface brief

Overview Use this command to display brief interface, configuration, and status information,

including provisioning information.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show interface brief

Mode User Exec and Privileged Exec

Output Figure 9-4: Example output from the show interface brief command

Commands

show interface

show interface memory

awplus# show interface brief 

Interface Status Protocol

port1.0.1 admin up down

port1.0.2 admin up down

port1.0.3 admin up down

port1.0.4 admin up down

.

port1.0.13 admin up down

port1.0.14 admin up down

lo admin up running

vlan1 admin up down 

Table 1: Parameters in the output of the show interface brief command

Parameter Description

Interface The name or type of interface.

Status The administrative state. This can be either admin up or admin

down.

Protocol The link state. This can be either down, running, or provisioned.

613-50137-01 Rev A Command Reference for FS980M Series 326

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE COMMANDS

SHOW INTERFACE MEMORY

show interface memory

Overview This command displays the shared memory used by either all interfaces, or the

specified interface or interfaces. The output is useful for diagnostic purposes by

Allied Telesis authorized service personnel.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show interface memory

show interface <port-list> memory

Mode User Exec and Privileged Exec

Example To display the shared memory used by all interfaces, use the command:

awplus# show interface memory

To display the shared memory used by port1.0.1 and port1.0.5 to port1.0.6, use the

command:

awplus# show interface port1.0.1,port1.0.5-1.0.6 memory

Parameter Description

<port-list> Display information about only the specified port or ports. The port

list can be:

• a switch port (e.g. port1.0.4), a static channel group (e.g. sa2) or a

dynamic (LACP) channel group (e.g. po2)

• a continuous range of ports separated by a hyphen (e.g.

port1.0.1-1.0.4, or sa1-2, or po1-2)

• a comma-separated list of ports and port ranges (e.g.

port1.0.1,port1.0.4-1.0.6). Do not mix switch ports, static channel

groups, and dynamic (LACP) channel groups in the same list.

613-50137-01 Rev A Command Reference for FS980M Series 327

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE COMMANDS

SHOW INTERFACE MEMORY

Output Figure 9-5: Example output from the show interface memory command

Figure 9-6: Example output from show interface <port-list> memory for a list

of interfaces

Commands

show interface brief

show interface status

show interface switchport

awplus#show interface memory

Vlan blocking state shared memory usage

---------------------------------------------

Interface shmid Bytes Used nattch Status

port1.0.1 393228 512 1

port1.0.2 458766 512 1

port1.0.3 360459 512 1

port1.0.4 524304 512 1

port1.0.5 491535 512 1

port1.0.6 557073 512 1

...

lo 425997 512 1

po1 1179684 512 1

po2 1212453 512 1

sa3 1245222 512 1

awplus#show interface port1.0.1,port1.0.5-1.0.6 memory

Vlan blocking state shared memory usage

---------------------------------------------

Interface shmid Bytes Used nattch Status

port1.0.1 393228 512 1

port1.0.5 491535 512 1

port1.0.6 557073 512 1

613-50137-01 Rev A Command Reference for FS980M Series 328

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE COMMANDS

SHOW INTERFACE STATUS

show interface status

Overview Use this command to display the status of the specified interface or interfaces.

Note that when no interface or interfaces are specified then the status of all

interfaces on the device are shown.

Syntax show interface [<port-list>] status

Examples To display the status of ports 1.0.1 to 1.0.4, use the commands:

awplus# show interface port1.0.1-1.0.4 status

To display the status of all ports, use the commands:

awplus# show interface status

Parameter Description

<port-list> The ports to display information about. The port list can be:

• a switch port (e.g. port1.0.6), a static channel group (e.g. sa2) or a

dynamic (LACP) channel group (e.g. po2)

• a continuous range of ports separated by a hyphen, e.g.

port1.0.1-1.0.6, or sa1-2, or po1-2

• a comma-separated list of ports and port ranges, e.g.

port1.0.1,port1.0.4-1.0.6. Do not mix switch ports, static channel

groups, and dynamic (LACP) channel groups in the same list

Table 2: Example output from the show interface <port-list> status command

awplus#show interface port1.0.1-1.0.4 status

Port Name Status Vlan Duplex Speed Type

port1.0.1 notconnect 1 auto auto 10GBASE-T

port1.0.2 notconnect 1 auto auto 10GBASE-T

port1.0.3 notconnect 1 auto auto 10GBASE-T

port1.0.4 notconnect 1 auto auto 10GBASE-T

Table 3: Example output from the show interface status command

awplus#show interface status 

Port Name Status Vlan Duplex Speed Type

port1.0.1 notconnect 1 auto auto 10GBASE-T

port1.0.2 notconnect 1 auto auto 10GBASE-T

port1.0.3 notconnect 1 auto auto 10GBASE-T

port1.0.4 notconnect 1 auto auto 10GBASE-T

port1.0.5 notconnect 1 auto auto 10GBASE-SR

port1.0.6 notconnect 1 auto auto not present

...

613-50137-01 Rev A Command Reference for FS980M Series 329

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE COMMANDS

SHOW INTERFACE STATUS

Commands

show interface

show interface memory

Table 4: Parameters in the output from the show interface status command

Parameter Description

Port Name/Type of the interface.

Name Description of the interface.

Status The administrative and operational status of the interface; one of:

• disabled: the interface is administratively down.

• connect: the interface is operationally up.

• notconnect: the interface is operationally down.

Vlan VLAN type or VLAN IDs associated with the port:

• When the VLAN mode is trunk, it displays trunk (it does not

display the VLAN IDs).

• When the VLAN mode is access, it displays the VLAN ID.

• When the VLAN mode is private promiscuous, it displays the

primary VLAN ID if it has one, and promiscuous if it does not

have a VLAN ID.

• When the VLAN mode is private host, it displays the primary

and secondary VLAN IDs.

• When the port is an Eth port, it displays none: there is no VLAN

associated with it.

• When the VLAN is dynamically assigned, it displays the current

dynamically assigned VLAN ID (not the access VLAN ID), or

dynamic if it has multiple VLANs dynamically assigned.

Duplex The actual duplex mode of the interface, preceded by a- if it has

autonegotiated this duplex mode. If the port is disabled or not

connected, it displays the configured duplex setting.

Speed The actual link speed of the interface, preceded by a- if it has

autonegotiated this speed. If the port is disabled or not

connected, it displays the configured speed setting.

Type The type of interface, e.g. 1000BaseTX. For SFP bays, it displays

Unknown if it does not recognize the type of SFP installed, or Not

present if an SFP is not installed or is faulty.

613-50137-01 Rev A Command Reference for FS980M Series 330

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE COMMANDS

SHUTDOWN

shutdown

Overview This command shuts down the selected interface. This administratively disables

the link and takes the link down at the physical (electrical) layer.

Use the no variant of this command to disable this function and therefore to bring

the link back up again.

Syntax shutdown

no shutdown

Mode Interface Configuration

Usage If you shutdown an aggregator, the device shows the admin status of the

aggregator and its component ports as “admin down”. While the aggregator is

down, the device accepts shutdown and no shutdown commands on

component ports, but these have no effect on port status. Ports will not come up

again while the aggregator is down.

Example To shut down port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# shutdown

To bring up port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no shutdown

To shut down vlan2, use the commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# shutdown

To bring up vlan2, use the commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# no shutdown

613-50137-01 Rev A Command Reference for FS980M Series 331

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Port Mirroring

Commands

Introduction

Overview This chapter provides an alphabetical reference of commands used to configure

Port Mirroring.

For more information, see the Mirroring Feature Overview and Configuration

Guide.

Command List •“mirror interface” on page 332

•“show mirror” on page 334

•“show mirror interface” on page 335

613-50137-01 Rev A Command Reference for FS980M Series 332

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PORT MIRRORING COMMANDS

MIRROR INTERFACE

mirror interface

Overview Use this command to define a mirror port and mirrored (monitored) ports and

direction of traffic to be mirrored. The port for which you enter interface mode will

be the mirror port.

The destination port is removed from all VLANs, and no longer participates in other

switching.

Use the no variant of this command to disable port mirroring by the destination

port on the specified source port.

Syntax mirror interface <source-port-list> direction

{both|receive|transmit}

no mirror interface <source-port-list>

Mode Interface Configuration

Usage Use this command to send traffic to another device connected to the mirror port

for monitoring.

For more information, see the Mirroring Feature Overview and Configuration

Guide.

A mirror port cannot be associated with a VLAN. If a switch port is configured to be

a mirror port, it is automatically removed from any VLAN it was associated with.

This command can only be applied to a single mirror (destination) port, not to a

range of ports, nor to a static or dynamic channel group. Do not apply multiple

interfaces with an interface command before issuing the mirror interface

command. One interface may have multiple mirror interfaces.

Parameter Description

<source-port-list> The source switch ports to mirror. A port-list can be:

• a port (e.g. port1.0.2)

• a continuous range of ports separated by a hyphen, e.g.

port1.0.1-1.0.2

• a comma-separated list of ports and port ranges, e.g.

port1.0.1,port1.0.4-1.0.6

The source port list cannot include dynamic or static

channel groups (link aggregators).

direction Specifies whether to mirror traffic that the source port

receives, transmits, or both.

both Mirroring traffic both received and transmitted by the

source port.

receive Mirroring traffic received by the source port.

transmit Mirroring traffic transmitted by the source port.

613-50137-01 Rev A Command Reference for FS980M Series 333

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PORT MIRRORING COMMANDS

MIRROR INTERFACE

Access control lists can be used to mirror a subset of traffic from the mirrored port

by using the copy-to-mirror parameter in hardware ACL commands.

Example To mirror traffic received and transmitted on port1.0.4 and port1.0.5 to destination

port1.0.3, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.3

awplus(config-if)# mirror interface port1.0.4,port1.0.5

direction both

Commands

access-list (numbered hardware ACL for IP packets)

access-list (numbered hardware ACL for MAC addresses)

default-action

613-50137-01 Rev A Command Reference for FS980M Series 334

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PORT MIRRORING COMMANDS

SHOW MIRROR

show mirror

Overview Use this command to display the status of all mirrored ports.

Syntax show mirror

Mode User Exec and Privileged Exec

Example To display the status of all mirrored ports, use the following command:

awplus# show mirror

Output Figure 10-1: Example output from the show mirror command

Mirror Test Port Name: port1.0.1

Mirror option: Enabled

Mirror direction: both

Monitored Port Name: port1.0.2

Mirror Test Port Name: port1.0.3

Mirror option: Enabled

Mirror direction: receive

Monitored Port Name: port1.0.4

Mirror Test Port Name: port1.0.3

Mirror option: Enabled

Mirror direction: receive

Monitored Port Name: port1.0.1

Mirror Test Port Name: port1.0.1

Mirror option: Enabled

Mirror direction: receive

Monitored Port Name: port1.0.3

Mirror Test Port Name: port1.0.1

Mirror option: Enabled

Mirror direction: transmit

Monitored Port Name: port1.0.4

613-50137-01 Rev A Command Reference for FS980M Series 335

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PORT MIRRORING COMMANDS

SHOW MIRROR INTERFACE

show mirror interface

Overview Use this command to display port mirroring configuration for a mirrored

(monitored) switch port.

Syntax show mirror interface <port>

Mode User Exec, Privileged Exec and Interface Configuration

Example To display port mirroring configuration for the port1.0.4, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# show mirror interface port1.0.4

Output Figure 10-2: Example output from the show mirror interface command

Parameter Description

<port>The monitored switch port to display information about.

Mirror Test Port Name: port1.0.3

Mirror option: Enabled

Mirror direction: both

Monitored Port Name: port1.0.4

613-50137-01 Rev A Command Reference for FS980M Series 336

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Interface Testing

Commands

Introduction

Overview This chapter provides an alphabetical reference of commands used for testing

interfaces.

Command List •“clear test interface” on page 337

•“service test” on page 338

•“test interface” on page 339

613-50137-01 Rev A Command Reference for FS980M Series 337

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE TESTING COMMANDS

CLEAR TEST INTERFACE

clear test interface

Overview This command clears test results and counters after issuing a test interface

command. Test results and counters must be cleared to issue subsequent test

interface commands later on.

Syntax clear test interface {<port-list>|all}

Mode Privileged Exec

Examples To clear the counters for port1.0.1 use the command:

awplus# clear test interface port1.0.1

To clear the counters for all interfaces use the command:

awplus# clear test interface all

Commands

test interface

Parameter Description

<port-list>The ports to test. A port-list can be:

• a switch port (e.g. port1.0.6)

• a continuous range of ports separated by a hyphen, e.g.

port1.0.1-port1.0.6

• a comma-separated list of the above, e.g.

port1.0.1,port1.0.5-1.0.6

The specified ports must exist.

all All interfaces

613-50137-01 Rev A Command Reference for FS980M Series 338

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE TESTING COMMANDS

SERVICE TEST

service test

Overview This command puts the device into the interface testing state, ready to begin

testing. After entering this command, enter Interface Configuration mode for the

desired interfaces and enter the command test interface.

Do not test interfaces on a device that is part of a live network—disconnect the

device first.

Use the no variant of this command to stop the test service.

Syntax service test

no service test

Mode Global Configuration

Example To put the device into a test state, use the command:

awplus(config)# service test

Commands

test interface

613-50137-01 Rev A Command Reference for FS980M Series 339

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE TESTING COMMANDS

TEST INTERFACE

test interface

Overview This command starts a test on a port or all ports or a selected range or list of ports.

Use the no variant of this command to disable this function. The test duration can

be configured by specifying the time in minutes after specifying a port or ports to

test.

For an example of all the commands required to test switch ports, see the

Examples section in this command. To test the Eth port, set its speed to 100 by

using the command speed 100.

NOTE: Do not run test interface on live networks because this will degrade network

performance.

Syntax test interface {<port-list>|all} [time{<1-60>|cont}]

no test interface {<port-list>|all}

Mode Privileged Exec

Parameter Description

<port-list>The ports to test. A port-list can be:

• a switch port (e.g. port1.0.6)

• a continuous range of ports separated by a hyphen, e.g.

port1.0.1-port1.0.6

• a comma-separated list of the above, e.g.

port1.0.1,port1.0.5-1.0.6

The specified ports must exist.

all All ports

time Keyword entered prior to the value for the time duration of the

interface test.

<1-60>Specifies duration of time to test the interface or interfaces in

minutes (from a minimum of 1 minute to a maximum of 60 minutes).

The default is 4 minutes.

cont Specifies continuous interface testing until canceled with command

negation.

613-50137-01 Rev A Command Reference for FS980M Series 340

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

INTERFACE TESTING COMMANDS

TEST INTERFACE

Example To test the switch ports in VLAN 1, install loopbacks in the ports, and enter the

following commands:

awplus(config)# service test

awplus(config)# no spanning-tree rstp enable bridge-forward

awplus(config)# interface vlan1

awplus(config-if)# shutdown

awplus(config-if)# end

awplus# test interface all

To see the output, use the commands:

awplus# show test

awplus# show test count

To start the test on all interfaces for 1 minute use the command:

awplus# test interface all time 1

Commands

clear test interface

613-50137-01 Rev A Command Reference for FS980M Series 341

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Part 2: Layer Two Switching

613-50137-01 Rev A Command Reference for FS980M Series 342

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Switching

Commands

Introduction

Overview This chapter provides an alphabetical reference of commands used to configure

switching.

For more information, see the Switching Feature Overview and Configuration

Guide.

Command List •“backpressure” on page 344

•“clear loop-protection counters” on page 346

•“clear mac address-table dynamic” on page 347

•“clear mac address-table static” on page 349

•“clear port counter” on page 350

•“clear port-security intrusion” on page 351

•“debug loopprot” on page 354

•“debug platform packet” on page 355

•“duplex” on page 357

•“flowcontrol (switch port)” on page 359

•“linkflap action” on page 361

•“loop-protection loop-detect” on page 362

•“loop-protection action” on page 363

•“loop-protection action-delay-time” on page 364

•“loop-protection timeout” on page 365

•“mac address-table acquire” on page 366

•“mac address-table ageing-time” on page 367

•“mac address-table static” on page 368

613-50137-01 Rev A Command Reference for FS980M Series 343

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

•“mac address-table thrash-limit” on page 369

•“platform jumboframe” on page 370

•“platform stop-unreg-mc-flooding” on page 371

•“polarity” on page 373

•“show debugging loopprot” on page 374

•“show debugging platform packet” on page 375

•“show flowcontrol interface” on page 376

•“show interface err-disabled” on page 377

•“show interface switchport” on page 378

•“show loop-protection” on page 379

•“show mac address-table” on page 381

•“show mac address-table thrash-limit” on page 383

•“show platform” on page 384

•“show platform classifier statistics utilization brief” on page 385

•“show platform port” on page 386

•“show port-security interface” on page 391

•“show port-security intrusion” on page 392

•“show storm-control” on page 393

•“speed” on page 394

•“storm-control level” on page 396

•“switchport port-security” on page 397

•“switchport port-security aging” on page 398

•“switchport port-security maximum” on page 399

•“switchport port-security violation” on page 400

•“thrash-limiting” on page 401

•“undebug loopprot” on page 402

•“undebug platform packet” on page 403

613-50137-01 Rev A Command Reference for FS980M Series 344

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

BACKPRESSURE

backpressure

Overview This command provides a method of applying flow control to ports running in half

duplex mode. The setting will only apply when the link is in the half-duplex state.

You can disable backpressure on an interface using the off parameter or the no

variant of this command.

Syntax backpressure {on|off}

no backpressure

Default Backpressure is turned off by default. You can determine whether an interface has

backpressure enabled by viewing the running-config output; backpressure on is

shown for interfaces if this feature is enabled.

Mode Interface Configuration

Usage The backpressure feature enables half duplex Ethernet ports to control traffic flow

during congestion by preventing further packets arriving. Back pressure utilizes a

pre-802.3x mechanism in order to apply Ethernet flow control to switch ports that

are configured in the half duplex mode.

The flow control applied by the flowcontrol (switch port) command operates only

on full-duplex links, whereas back pressure operates only on half-duplex links.

If a port has insufficient capacity to receive further frames, the device will simulate

a collision by transmitting a CSMACD jamming signal from this port until the buffer

empties. The jamming signal causes the sending device to stop transmitting and

wait a random period of time, before retransmitting its data, thus providing time

for the buffer to clear. Although this command is only valid for switch ports

operating in half-duplex mode the remote device (the one sending the data) can

be operating in the full duplex mode.

To see the currently-negotiated duplex mode for ports whose links are up, use the

command show interface. To see the configured duplex mode (when different

from the default), use the command show running-config.

Examples To enable back pressure flow control on interfaces port1.0.1-port1.0.2

enter the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.1-port1.0.2

awplus(config-if)# backpressure on

Parameters Description

on Enables half-duplex flow control.

off Disables half-duplex flow control.

613-50137-01 Rev A Command Reference for FS980M Series 345

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

BACKPRESSURE

To disable back pressure flow control on interface port1.0.2 enter the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# backpressure off

Validation

Commands

show running-config

show interface

Commands

duplex

613-50137-01 Rev A Command Reference for FS980M Series 346

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

CLEAR LOOP-PROTECTION COUNTERS

clear loop-protection counters

Overview Use this command to clear the counters for the Loop Protection counters.

Syntax clear loop-protection [interface <port-list>] counters

Mode Privileged Exec

Examples To clear the counter information for all interfaces:

awplus# clear loop-protection counters

To clear the counter information for a single port:

awplus# clear loop-protection interface port1.0.1 counters

Parameters Description

interface The interface whose counters are to be cleared.

<port-list>A port, a port range, or an aggregated link.

613-50137-01 Rev A Command Reference for FS980M Series 347

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

CLEAR MAC ADDRESS-TABLE DYNAMIC

clear mac address-table dynamic

Overview Use this command to clear the filtering database of all entries learned for a selected

MAC address, an MSTP instance, a switch port interface or a VLAN interface.

Syntax clear mac address-table dynamic [address

<mac-address>|interface <port> [instance <inst>]|vlan <vid>]

Mode Privileged Exec

Usage Use this command with options to clear the filtering database of all entries learned

for a given MAC address, interface or VLAN. Use this command without options to

clear any learned entries.

Use the optional instance parameter to clear the filtering database entries

associated with a specified MSTP instance Note that you must first specify a switch

port interface before you can specify an MSTP instance.

Compare this usage and operation with the clear mac address-table static

command. Note that an MSTP instance cannot be specified with the command

clear mac address-table static.

Examples This example shows how to clear all dynamically learned filtering database entries

for all interfaces, addresses, VLANs.

awplus# clear mac address-table dynamic

This example shows how to clear all dynamically learned filtering database entries

when learned through device operation for the MAC address 0000.5E00.5302.

awplus# clear mac address-table dynamic address 0000.5E00.5302

Parameter Description

address Specify a MAC (Media Access Control) address to be cleared from

the filtering database.

<mac-address> Enter a MAC address to be cleared from the database in the format

HHHH.HHHH.HHHH.

interface Specify a switch port to be cleared from the filtering database.

instance Specify an MSTP (Multiple Spanning Tree) instance to be cleared

from the filtering database.

<inst> Enter an MSTP instance in the range 1 to 63 to be cleared from the

filtering database.

vlan Specify a VLAN to be cleared from the filtering database.

<vid> Enter a VID (VLAN ID) in the range 1 to 4094 to be cleared from the

filtering database.

613-50137-01 Rev A Command Reference for FS980M Series 348

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

CLEAR MAC ADDRESS-TABLE DYNAMIC

This example shows how to clear all dynamically learned filtering database entries

when learned through device operation for a given MSTP instance 1 on switch port

interface port1.0.2.

awplus# clear mac address-table dynamic interface port1.0.2

instance 1

Commands

clear mac address-table static

show mac address-table

613-50137-01 Rev A Command Reference for FS980M Series 349

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

CLEAR MAC ADDRESS-TABLE STATIC

clear mac address-table static

Overview Use this command to clear the filtering database of all statically configured entries

for a selected MAC address, interface, or VLAN.

Syntax clear mac address-table static [address <mac-address>|interface

<port>|vlan <vid>]

Mode Privileged Exec

Usage Use this command with options to clear the filtering database of all entries made

from the CLI for a given MAC address, interface or VLAN. Use this command

without options to clear any entries made from the CLI.

Compare this usage with clear mac address-table dynamic command.

Examples This example shows how to clear all filtering database entries configured through

the CLI.

awplus# clear mac address-table static

This example shows how to clear all filtering database entries for a specific

interface configured through the CLI.

awplus# clear mac address-table static interface port1.0.3

This example shows how to clear filtering database entries configured through the

CLI for the mac address 0000.5E00.5302.

awplus# clear mac address-table static address 0000.5E00.5302

Commands

clear mac address-table dynamic

mac address-table static

show mac address-table

Parameter Description

address The MAC address whose entries are to be cleared from the filtering

database.

<mac-address> Specifies the MAC (Media Access Control) address to be cleared

from. Enter this address in the format HHHH.HHHH.HHHH.

interface Specify the interface from which statically configured entries are

to be cleared.

<port> Specify the switch port from which address entries will be cleared.

This can be a single switch port, (e.g. port1.0.4), a static channel

group (e.g. sa2), or a dynamic (LACP) channel group (e.g. po2).

vlan A VLAN whose statically configured entries are to be cleared.

<vid> Specifies the VLAN ID whose statically configured entries are to be

cleared.

613-50137-01 Rev A Command Reference for FS980M Series 350

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

CLEAR PORT COUNTER

clear port counter

Overview Use this command to clear the packet counters of the port.

Syntax clear port counter [<port>]

Mode Privileged Exec

Example To clear the packet counter for port1.0.1, use the command:

awplus# clear port counter port1.0.1

Commands

show platform port

Parameter Description

<port> The port number or range

613-50137-01 Rev A Command Reference for FS980M Series 351

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

CLEAR PORT-SECURITY INTRUSION

clear port-security intrusion

Overview Use this command to clear the history of the port-security intrusion list on all ports,

or an individual port. If a port is not specified, the intrusion lists of all ports are

cleared. This command does not clear any MAC addresses the device has already

learned on the ports. If you want to clear MAC addresses on a switch port from the

filtering database, you can use the clear mac address-table dynamic command or

the clear mac address-table static command.

Syntax clear port-security intrusion [interface <port>]

Mode Privileged Exec

Examples To see the port-security status on port1.0.1, use the following command:

awplus# show port-security interface port1.0.1

To see the intrusion list on port1.0.1, use the following command:

awplus# show port-security intrusion interface port1.0.1

Parameter Description

<port> Specify the switch port from which the history of violated address

entries will be cleared. The port can be a single switch port, (e.g.

port1.0.4), a static channel group (e.g. sa2), or a dynamic

(LACP) channel group (e.g. po2).

Table 1: Example output from the show port-security interface command



awplus#show port-security interface port1.0.1

Port Security configuration

------------------------------------------------------------

Security Enabled : YES

Port Status : ENABLED

Violation Mode : TRAP

Aging : OFF

Maximum MAC Addresses : 1

Total MAC Addresses : 1

Lock Status : LOCKED

Security Violation Count : 1

Last Violation Source Address : 801f.0200.19da

613-50137-01 Rev A Command Reference for FS980M Series 352

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

CLEAR PORT-SECURITY INTRUSION

To clear the history of port-security intrusion list on port1.0.1, use the following

command:

awplus# clear port-security intrusion interface port1.0.1

To see the port-security status on port1.0.1, use the following command:

awplus# show port-security interface port1.0.1

NOTE: Note that the port status is still locked while the history of port violation is

cleared from the database.

To see the intrusion list on port1.0.1, use the following command:

awplus# show port-security intrusion interface port1.0.1

Table 2: Example output from the show port-security intrusion command



awplus#show port-security intrusion interface port1.0.1

Port Security Intrusion List

------------------------------------------------------------

Interface: port1.0.1 - 1 intrusion(s) detected

801f.0200.19da

Table 3: Example output from the show port-security interface command



awplus#show port-security interface port1.0.1

Port Security configuration

------------------------------------------------------------

Security Enabled : YES

Port Status : ENABLED

Violation Mode : TRAP

Aging : OFF

Maximum MAC Addresses : 1

Total MAC Addresses : 1

Lock Status : LOCKED

Security Violation Count : 0

Last Violation Source Address : None

Table 4: Example output from the show port-security intrusion command



awplus#show port-security intrusion interface port1.0.1

Port Security Intrusion List

------------------------------------------------------------

Interface: port1.0.1 - no intrusions detected

613-50137-01 Rev A Command Reference for FS980M Series 353

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

CLEAR PORT-SECURITY INTRUSION

Commands

show port-security interface

show port-security intrusion

switchport port-security

switchport port-security aging

switchport port-security maximum

switchport port-security violation

613-50137-01 Rev A Command Reference for FS980M Series 354

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

DEBUG LOOPPROT

debug loopprot

Overview This command enables Loop Protection debugging.

The no variant of this command disables Loop Protection debugging.

Syntax debug loopprot {info|msg|pkt|state|nsm|all}

no debug loopprot {info|msg|pkt|state|nsm|all}

Mode Privileged Exec and Global Configuration

Example To enable debug for all state transitions, use the command:

awplus# debug loopprot state

Commands

show debugging loopprot

undebug loopprot

Parameter Description

info General Loop Protection information.

msg Received and transmitted Loop Detection Frames (LDFs).

pkt Echo raw ASCII display of received and transmitted LDF packets to

the console.

state Loop Protection states transitions.

nsm Network Service Module information.

all All debugging information.

613-50137-01 Rev A Command Reference for FS980M Series 355

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

DEBUG PLATFORM PACKET

debug platform packet

Overview This command enables platform to CPU level packet debug functionality on the

device.

Use the no variant of this command to disable platform to CPU level packet debug.

If the result means both send and receive packet debug are disabled, then any

active timeout will be canceled.

Syntax debug platform packet [recv] [send] [timeout <timeout>] [vlan

<vlan-id>|all]

no debug platform packet [recv] [send]

Default A 5 minute timeout is configured by default if no other timeout duration is

specified.

Mode Privileged Exec and Global Configuration

Usage This command can be used to trace packets sent and received by the CPU. If a

timeout is not specified, then a default 5 minute timeout will be applied.

If a timeout of 0 is specified, packet debug will be generated until the no variant of

this command is used or another timeout value is specified. The timeout value

applies to both send and receive debug and is updated whenever the debug

platform packet command is used.

Examples To enable both receive and send packet debug for the default timeout of 5

minutes, enter:

awplus# debug platform packet

To enable receive packet debug for 10 seconds, enter:

awplus# debug platform packet recv timeout 10

To enable send packet debug with no timeout, enter:

awplus# debug platform packet send timeout 0

Parameter Description

recv Debug packets received.

send Debug packets sent.

timeout Stop debug after a specified time.

<timeout><0-3600>The timeout period, specified in seconds.

vlan Limit debug to a single VLAN ID specified.

<vlan-id><1-4094> The VLAN ID to limit the debug output on.

all Debug all VLANs (default setting).

613-50137-01 Rev A Command Reference for FS980M Series 356

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

DEBUG PLATFORM PACKET

To enable VLAN packet debug for VLAN 2 with a timeout duration of 3 minutes,

enter:

awplus# debug platform packet vlan 2 timeout 150

To disable receive packet debug, enter:

awplus# no debug platform packet recv

Commands

show debugging platform packet

undebug platform packet

613-50137-01 Rev A Command Reference for FS980M Series 357

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

DUPLEX

duplex

Overview This command changes the duplex mode for the specified port.

To see the currently-negotiated duplex mode for ports whose links are up, use the

command show interface. To see the configured duplex mode (when different

from the default), use the command show running-config.

Syntax duplex {auto|full|half}

Default By default, ports auto-negotiate duplex mode (except for 100Base-FX ports which

do not support auto-negotiation, so default to full duplex mode).

Mode Interface Configuration

Usage Switch ports in a static or dynamic (LACP) channel group must have the same port

speed and be in full duplex mode. Once switch ports have been aggregated into a

channel group, you can set the duplex mode of all the switch ports in the channel

group by applying this command to the channel group.

Examples To specify full duplex for port1.0.4, enter the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# duplex full

To specify half duplex for port1.0.4, enter the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# duplex half

To auto-negotiate duplex mode for port1.0.4, enter the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# duplex auto

Parameter Description

auto Auto-negotiate duplex mode.

full Operate in full duplex mode only.

half Operate in half duplex mode only.

613-50137-01 Rev A Command Reference for FS980M Series 358

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

DUPLEX

Commands

backpressure

polarity

speed

show interface

613-50137-01 Rev A Command Reference for FS980M Series 359

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

FLOWCONTROL (SWITCH PORT)

flowcontrol (switch port)

Overview Use this command to enable flow control, and configure the flow control mode for

the switch port.

Use the no variant of this command to disable flow control for the specified switch

port.

Syntax flowcontrol {send|receive} {off|on}

no flowcontrol

Default By default, flow control is disabled.

Mode Interface Configuration

Usage The flow control mechanism specified by 802.3x is only for full duplex links. It

operates by sending PAUSE frames to the link partner to temporarily suspend

transmission on the link

Flow control enables connected Ethernet ports to control traffic rates during

congestion by allowing congested nodes to pause link operation at the other end.

If one port experiences congestion, and cannot receive any more traffic, it notifies

the other port to stop sending until the condition clears. When the local device

detects congestion at its end, it notifies the remote device by sending a pause

frame. On receiving a pause frame, the remote device stops sending data packets,

which prevents loss of data packets during the congestion period.

Flow control is not recommended when running QoS or ACLs, because the

complex queuing, scheduling, and filtering configured by QoS or ACLs may be

slowed by applying flow control.

For half-duplex links, an older form of flow control known as backpressure is

supported. See the related backpressure command.

For flow control on async serial (console) ports, see the flowcontrol hardware

(asyn/console) command.

Parameter Description

receive When the port receives pause frames, it temporarily stops (pauses)

sending traffic.

on Enable the specified flow control.

off Disable the specified flow control.

send When the port is congested (receiving too much traffic), it sends

pause frames to request the other end to temporarily stop (pause)

sending traffic.

613-50137-01 Rev A Command Reference for FS980M Series 360

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

FLOWCONTROL (SWITCH PORT)

Examples awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# flowcontrol receive on

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# flowcontrol send on

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# flowcontrol receive off

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# flowcontrol send off

Validation

Commands

show running-config

Commands

backpressure

613-50137-01 Rev A Command Reference for FS980M Series 361

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

LINKFLAP ACTION

linkflap action

Overview Use this command to detect flapping on all ports. If more than 15 flaps occur in less

than 15 seconds the flapping port will shut down.

Use the no variant of this command to disable flapping detection at this rate.

Syntax linkflap action [shutdown]

no linkflap action

Default Linkflap action is disabled by default.

Mode Global Configuration

Example To enable the linkflap action command on the device, use the following

commands:

awplus# configure terminal

awplus(config)# linkflap action shutdown

Parameter Description

linkflap Global setting for link flapping.

action Specify the action for port.

shutdown Shutdown the port.

613-50137-01 Rev A Command Reference for FS980M Series 362

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

LOOP-PROTECTION LOOP-DETECT

loop-protection loop-detect

Overview Use this command to enable the loop-protection loop-detect feature and

configure its parameters.

Use the no variant of this command to disable the loop-protection loop-detect

feature.

Syntax loop-protection loop-detect [ldf-interval <period>]

[ldf-rx-window <frames>] [fast-block]

no loop-protection loop-detect

Default The loop-protection loop-detect feature is disabled by default. The default interval

is 10 seconds, and the default window size is 3 frames.

Mode Global Configuration

Usage See the “Loop Protection” section in the Switching Feature Overview and

Configuration Guide for relevant conceptual, configuration, and overview

information prior to applying this command.

Example To enable the loop-detect mechanism on the switch, and generate loop-detect

frames once every 5 seconds, use the following commands:

awplus# configure terminal

awplus(config)# loop-protection loop-detect ldf-interval 5

Commands

loop-protection action

loop-protection timeout

show loop-protection

thrash-limiting

Parameter Description

ldf-interval The time (in seconds) between successive loop-detect frames

being sent.

<period> Specify a period between 1 and 600 seconds. The default is 10

seconds.

ldf-rx-window The number of transmitted loop detect frames whose details

are held for comparing with frames arriving at the same port.

<frames> Specify a value for the window size between 1 and 5 frames.

The default is 3 frames.

[fast-block] The fast-block blocks transmitting port to keep partial

connectivity.

613-50137-01 Rev A Command Reference for FS980M Series 363

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

LOOP-PROTECTION ACTION

loop-protection action

Overview Use this command to specify the protective action to apply when a network loop

is detected on an interface.

Use the no variant of this command to reset the loop protection actions to the

default action, vlan-disable, on an interface.

Syntax loop-protection action

{link-down|log-only|port-disable|vlan-disable|none}

no loop-protection action

Default loop-protection action vlan-disable

Mode Interface Configuration

Usage See the “Loop Protection” section in the Switching Feature Overview and

Configuration Guide for relevant conceptual, configuration, and overview

information prior to applying this command.

Example To disable the interface port1.0.4 and bring the link down when a network

loop is detected, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# loop-protection action link-down

Commands

loop-protection loop-detect

loop-protection timeout

show loop-protection

thrash-limiting

Parameter Description

link-down Block all traffic on a port (or aggregated link) that detected the

loop, and take down the link.

log-only Details of loop conditions are logged. No action is applied to the

port (or aggregated link).

port-disable Block all traffic on interface for which the loop occurred, but keep

the link in the up state.

vlan-disable Block all traffic for the VLAN on which the loop traffic was

detected. Note that setting this parameter will also enable ingress

filtering. This is the default action.

none Applies no protective action.

613-50137-01 Rev A Command Reference for FS980M Series 364

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

LOOP-PROTECTION ACTION-DELAY-TIME

loop-protection action-delay-time

Overview Use this command to sets the loop protection action delay time for an interface to

specified values in seconds. The action delay time specifies the waiting period for

the action.

Use the no variant of this command to reset the loop protection action delay time

for an interface to default.

Syntax loop-protection action-delay-time <0-86400>

no loop-protection action

Default Action delay timer is disabled by default.

Mode Interface Configuration

Example To configure a loop protection action delay time of 10 seconds on port 1.0.4, use

the commands:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# loop-protection action-delay-time 10

Commands

show loop-protection

Parameter Description

<0-86400> Time in seconds; 0 means action delay timer is disabled.

613-50137-01 Rev A Command Reference for FS980M Series 365

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

LOOP-PROTECTION TIMEOUT

loop-protection timeout

Overview Use this command to specify the Loop Protection recovery action duration on an

interface.

Use the no variant of this command to set the loop protection timeout to the

default.

Syntax loop-protection timeout <duration>

no loop-protection timeout

Default The default is 7 seconds.

Mode Interface Configuration

Usage See the “Loop Protection” section in the Switching Feature Overview and

Configuration Guide for relevant conceptual, configuration, and overview

information prior to applying this command.

Example To configure a loop protection action timeout of 10 seconds for port1.0.4, use

the command:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# loop-protection timeout 10

Parameter Description

<duration> The time (in seconds) for which the configured action will apply

before being disabled. This duration can be set between 0 and 86400

seconds (24 hours). The set of 0 means infinity so timeout does not

expire.

613-50137-01 Rev A Command Reference for FS980M Series 366

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

MAC ADDRESS-TABLE ACQUIRE

mac address-table acquire

Overview Use this command to enable MAC address learning on the device.

Use the no variant of this command to disable learning.

Syntax mac address-table acquire

no mac address-table acquire

Default Learning is enabled by default for all instances.

Mode Global Configuration

Example awplus# configure terminal

awplus(config)# mac address-table acquire

613-50137-01 Rev A Command Reference for FS980M Series 367

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

MAC ADDRESS-TABLE AGEING-TIME

mac address-table ageing-time

Overview Use this command to specify an ageing-out time for a learned MAC address. The

learned MAC address will persist for at least the specified time.

The no variant of this command will reset the ageing-out time back to the default

of 300 seconds (5 minutes).

Syntax mac address-table ageing-time <ageing-timer> none

no mac address-table ageing-time

Default The default ageing time is 300 seconds.

Mode Global Configuration

Examples The following commands specify various ageing timeouts on the device:

awplus# configure terminal

awplus(config)# mac address-table ageing-time 1000

awplus# configure terminal

awplus(config)# mac address-table ageing-time none

awplus# configure terminal

awplus(config)# no mac address-table ageing-time

Parameter Description

<ageing-timer> <10-1000000> The number of seconds of persistence.

none Disable learned MAC address timeout.

613-50137-01 Rev A Command Reference for FS980M Series 368

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

MAC ADDRESS-TABLE STATIC

mac address-table static

Overview Use this command to statically configure the MAC address-table to forward or

discard frames with a matching destination MAC address.

Syntax mac address-table static <mac-addr> {forward|discard} interface

<port> [vlan <vid>]

no mac address-table static <mac-addr> {forward|discard}

interface <port> [vlan <vid>]

Mode Global Configuration

Usage The mac address-table static command is only applicable to Layer 2 switched

traffic within a single VLAN. Do not apply the mac address-table static command

to Layer 3 switched traffic passing from one VLAN to another VLAN. Frames will not

be discarded across VLANs because packets are routed across VLANs. This

command only works on Layer 2 traffic.

Example awplus# configure terminal

awplus(config)# mac address-table static 2222.2222.2222 forward

interface port1.0.4 vlan 3

Commands

clear mac address-table static

show mac address-table

Parameter Description

<mac-addr> The destination MAC address in HHHH.HHHH.HHHH format.

<port>The port to display information about. The port may be a switch port

(e.g. port1.0.4), a static channel group (e.g. sa2), or a dynamic

(LACP) channel group (e.g. po2).

<vid> The VLAN ID. If you do not specify a VLAN, its value defaults to vlan 1.

613-50137-01 Rev A Command Reference for FS980M Series 369

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

MAC ADDRESS-TABLE THRASH-LIMIT

mac address-table thrash-limit

Overview Use this command to set the thrash limit on the device or stack.

Thrashing occurs when a MAC address table rapidly “flips” its mapping of a single

MAC address between two subnets, usually as a result of a network loop.

Use the no variant of this command to disable thrash limiting.

Syntax mac address-table thrash-limit <rate>

no mac address-table thrash-limit

Default No thrash limiting

Mode Global Configuration

Usage Use this command to limit thrashing on the selected port range.

Example To apply a thrash limit of 100 MAC address flips per second:

awplus# configure terminal

awplus(config)# mac address-table thrash-limit 100

Commands

show mac address-table thrash-limit

Parameter Description

<rate> sets the maximum thrash rate at which limiting is applied. This rate can

be set between 5 and 255 MAC thrashing flips per second. Once the

thrash limit rate is reached, the port is considered to be thrashing.

613-50137-01 Rev A Command Reference for FS980M Series 370

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

PLATFORM JUMBOFRAME

platform jumboframe

Overview This command enables the device to forward jumbo frames. See the Switching

Feature Overview and Configuration Guide for more information.

When jumbo frame support is enabled, the maximum size of packets that the

device can forward is 10240 bytes.

The no variant of this command disables the device from forwarding jumbo

frames. This stops the ports from forwarding packets larger than VLAN tagged

frames (1522 bytes).

Syntax platform jumboframe

no platform jumboframe

Default By default, jumbo frames is off.

Mode Global Configuration

Usage You must restart the device after entering this command for it to take effect. You

can use the reboot command to restart the device.

Example To enable the device to forward jumbo frames, use the following commands:

awplus# configure terminal

awplus(config)# platform jumboframe

Commands

show platform

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 371

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

PLATFORM STOP-UNREG-MC-FLOODING

platform stop-unreg-mc-flooding

Overview If a multicast stream is arriving at a network device, and that network device has

received no IGMP reports that request the receipt of the stream, then that stream

is referred to as "unregistered". IGMP snooping actively prevents the flooding of

unregistered streams to all ports in the VLAN on which the stream is received.

However, there are brief moments at which this prevention is not in operation, and

an unregistered stream may be briefly flooded. This command stops this flooding

during even those brief periods when IGMP snooping is not explicitly preventing

the flooding.

Use the no variant of this command to revert to default behavior and disable this

feature.

NOTE: This command should not be used within any IPv6 networks. IPv6 neighbor

discovery operation is inhibited by this feature.

This command does not affect the flooding of Local Network Control Block IPv4

multicast packets in the address range 224.0.0.1 to 224.0.0.255 (224.0.0/24). Such

packets will continue to be uninterruptedly flooded, as they need to be.

Syntax platform stop-unreg-mc-flooding

no platform stop-unreg-mc-flooding

Default This feature is disabled by default.

Mode Global Configuration

Usage This command stops the periodic flooding of unknown or unregistered multicast

packets when the Group Membership interval timer expires and there are no

subscribers to a multicast group. If there is multicast traffic in a VLAN without

subscribers, multicast traffic temporarily floods out of the VLAN when the Group

Membership interval timer expires, which happens when the switch does not get

replies from Group Membership queries.

This command also stops the initial flood of multicast packets that happens when

a new multicast source starts to send traffic. This flooding lasts until snooping

realises that this the multicast group is arriving at the switch, and puts an entry into

hardware to prevent it from being flooded.

This command is useful in networks where low-performance devices are attached.

The operation of such devices can be impaired by them receiving unnecessary

streams of traffic. For example, in sites where IP cameras are in use, the flooding of

video streams to a whole VLAN can send enough traffic to the cameras to cause

interruption of their video streaming.

Output Do not use this command in IPv6 networks. The following console message is

displayed after entering this command to warn you of this:

% WARNING: IPv6 will not work with this setting enabled

% Please consult the documentation for more information

613-50137-01 Rev A Command Reference for FS980M Series 372

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

PLATFORM STOP-UNREG-MC-FLOODING

Examples To enable this feature and stop multicast packet flooding, use the following

commands:

awplus# configure terminal

awplus(config)# platform stop-unreg-mc-flooding

To disable this feature and allow multicast packet flooding, use the following

commands:

awplus# configure terminal

awplus(config)# no platform stop-unreg-mc-flooding

Commands

show platform

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 373

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

POLARITY

polarity

Overview This command sets the MDI/MDIX polarity on a copper-based switch port.

Syntax polarity {auto|mdi|mdix}

Default By default, switch ports set the polarity automatically (auto).

Mode Interface Configuration

Usage We recommend the default auto setting for MDI/MDIX polarity. Polarity applies to

copper 10BASE-T, 100BASE-T, and 1000BASE-T switch ports; It does not apply to

fiber ports. See the “MDI/MDIX Connection Modes” section in the Switching

Feature Overview and Configuration Guide for more information.

Example To set the polarity for port1.0.6 to fixed MDI mode, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.6

awplus(config-if)# polarity mdi

Parameter Description

mdi Sets the polarity to MDI (medium dependent interface).

mdix Sets the polarity to MDI-X (medium dependent interface crossover).

auto The switch port sets the polarity automatically. This is the default option.

613-50137-01 Rev A Command Reference for FS980M Series 374

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW DEBUGGING LOOPPROT

show debugging loopprot

Overview This command shows Loop Protection debugging information.

Syntax show debugging loopprot

Mode User Exec and Privileged Exec

Example To display the enabled Loop Protection debugging modes, use the command:

awplus# show debugging loopprot

Commands

debug loopprot

613-50137-01 Rev A Command Reference for FS980M Series 375

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW DEBUGGING PLATFORM PACKET

show debugging platform packet

Overview This command shows platform to CPU level packet debugging information.

Syntax show debugging platform packet

Mode User Exec and Privileged Exec

Example To display the platform packet debugging information, use the command:

awplus# show debugging platform packet

Commands

debug platform packet

undebug platform packet

613-50137-01 Rev A Command Reference for FS980M Series 376

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW FLOWCONTROL INTERFACE

show flowcontrol interface

Overview Use this command to display flow control information.

Syntax show flowcontrol interface <port>

Mode User Exec and Privileged Exec

Example To display the flow control for the port1.0.5, use the command:

awplus# show flowcontrol interface port1.0.5

Output Figure 12-1: Example output from the show flowcontrol interface command

for a specific interface

Parameter Description

<port> Specifies the name of the port to be displayed.

Port Send FlowControl Receive FlowControl RxPause TxPause

admin oper admin oper

----- ------- -------- ------- -------- ------- -------

port1.0.5 on on on on 0 0

613-50137-01 Rev A Command Reference for FS980M Series 377

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW INTERFACE ERR-DISABLED

show interface err-disabled

Overview Use this command to show the ports which have been dynamically shut down by

protocols running on the device and the protocols responsible for the shutdown.

Syntax show interface [<interface-range> err-disabled]

Mode User Exec and Privileged Exec

Example To show which protocols have shut down ports, use the commands:

awplus# show interface err-disabled

Output Figure 12-2: Example output from show interface err-disabled

Parameter Description

<interface-range> Interface range

err-disabled Brief summary of interfaces shut down by protocols

awplus#show interface err-disabled

Interface Reason

port1.0.1 loop protection

port1.0.2 loop protection

613-50137-01 Rev A Command Reference for FS980M Series 378

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW INTERFACE SWITCHPORT

show interface switchport

Overview Use this command to show VLAN information about each switch port.

Syntax show interface switchport

Mode User Exec and Privileged Exec

Example To display VLAN information about each switch port, enter the command:

awplus# show interface switchport

Output Figure 12-3: Example output from the show interface switchport command

Commands

show interface memory

Interface name : port1.0.1

Switchport mode : access

Ingress filter : enable

Acceptable frame types : all

Default Vlan : 2

Configured Vlans : 2



Interface name : port1.0.2

Switchport mode : trunk

Ingress filter : enable

Acceptable frame types : all

Default Vlan : 1

Configured Vlans : 1 4 5 6 7 8

...

613-50137-01 Rev A Command Reference for FS980M Series 379

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW LOOP-PROTECTION

show loop-protection

Overview Use this command to display the current loop protection setup for the device.

Syntax show loop-protection [interface <port-list>] [counters]

Mode User Exec and Privileged Exec

Usage This command is used to display the current configuration and operation of the

Loop Protection feature

Examples To display the current configuration status, use the command:

awplus# show loop-protection

Figure 12-4: Example output from the show loop-protection command

To display the counter information, use the command:

awplus# show loop-protection counters

Figure 12-5: Example output from the show loop-protection counters

command

Parameter Description

interface The interface selected for display.

<port-list>A port, a port range, or an aggregated link.

counters Displays counter information for loop protection.

awplus#show loop-protection



LDF Interval: 10

LDF Rx Window: 3

Fast Block: Disabled

Timeout

Int Enabled Action Status Timeout Remain Rx port

--------------------------------------------------------------------------

port1.0.1 Yes vlan-dis Normal 7 - -

port1.0.2 Yes vlan-dis Normal 7 - -

port1.0.3 Yes vlan-dis Normal 7 - -

...

613-50137-01 Rev A Command Reference for FS980M Series 380

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW LOOP-PROTECTION

awplus#show loop-protection counters



Switch Loop Detection Counter



Interface Tx Rx Rx Invalid Last LDF Rx

-------------------------------------------------------------------------

port1.0.1

vlan1 60 0 0 -

port1.0.2

vlan1 0 0 0 -

port1.0.3

vlan1 0 0 0 -

...

613-50137-01 Rev A Command Reference for FS980M Series 381

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW MAC ADDRESS-TABLE

show mac address-table

Overview Use this command to display the mac address-table for all configured VLANs.

Syntax show mac address-table

Mode User Exec and Privileged Exec

Usage The show mac address-table command is only applicable to view a mac

address-table for Layer 2 switched traffic within VLANs.

Example To display the mac address-table, use the following command:

awplus# show mac address-table

Output See the below sample output captured when there was no traffic being switched:

See the sample output captured when packets were switched and mac addresses

were learned:

Note the new mac addresses learned for port1.0.4 and port1.0.6 added as

dynamic entries.

Note the first column of the output below shows VLAN IDs if multiple VLANs are

configured:

Also note manually configured static mac-addresses are shown to the right of the

type column:

awplus#show mac address-table



VLAN Port MAC State

1 unknown 0000.cd28.0752 static

ARP - 0000.cd00.0000 static

awplus#show mac address-table



VLAN Port MAC State

1 unknown 0000.cd28.0752 static

1 port1.0.6 0030.846e.9bf4 dynamic

1 port1.0.4 0030.846e.bac7 dynamic

ARP - 0000.cd00.0000 static

awplus#show mac address-table



VLAN Port MAC State

1 unknown 0000.cd28.0752 static

1 port1.0.4 0030.846e.bac7 dynamic

2 unknown 0000.cd28.0752 static

2 port1.0.6 0030.846e.9bf4 dynamic 

ARP - 0000.cd00.0000 static

613-50137-01 Rev A Command Reference for FS980M Series 382

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW MAC ADDRESS-TABLE

Commands

clear mac address-table dynamic

clear mac address-table static

mac address-table static

awplus(config)#mac address-table static 0000.1111.2222 for int 

port1.0.3 vlan 2

awplus(config)#end

awplus#

awplus#show mac address-table



VLAN Port MAC State

1 unknown 0000.cd28.0752 static

1 port1.0.2 0030.846e.bac7 dynamic

2 port1.0.3 0000.1111.2222 static

2 unknown 0000.cd28.0752 static

2 port1.0.5 0030.846e.9bf4 dynamic

ARP - 0000.cd00.0000 static

613-50137-01 Rev A Command Reference for FS980M Series 383

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW MAC ADDRESS-TABLE THRASH-LIMIT

show mac address-table thrash-limit

Overview Use this command to display the current thrash limit set for all interfaces on the

device.

Syntax show mac address-table thrash-limit

Mode User Exec and Privileged Exec

Example To display the current, use the following command:

awplus# show mac address-table thrash-limit

Output Figure 12-6: Example output from the show mac address-table thrash-limit

command

Commands

mac address-table thrash-limit

% Thrash-limit 7 movements per second

613-50137-01 Rev A Command Reference for FS980M Series 384

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW PLATFORM

show platform

Overview This command displays the settings configured by using the platform commands.

Syntax show platform

Mode Privileged Exec

Usage This command displays the settings in the running config. For changes in some of

these settings to take effect, the device must be rebooted with the new settings in

the startup config.

Example To check the settings configured with platform commands on the device, use the

following command:

awplus# show platform

Output Figure 12-7: Example output from the show platform command

awplus#show platform



MAC vlan hashing algorithm crc32l

L3 hashing algorithm crc32l

stop-unreg-mc-flooding off

Vlan-stacking TPID 0x8100

Hardware Filter Size ipv4-limited-ipv6

Table 5: Parameters in the output of the show platform command

Parameter Description

MAC vlan hashing

algorithm

The MAC VLAN hash-key-generating algorithm (set with

the platform mac-vlan-hashing-algorithm command). The

default algorithm is crc32l. The algorithm may need to be

changed in rare circumstances in which hash collisions

occur.

L3 hashing algorithm The L3 VLAN hash-key-generating algorithm (set with the

platform l3-vlan-hashing-algorithm command). The

default algorithm is crc32l. The algorithm may need to be

changed in rare circumstances in which hash collisions

occur.

stop-unreg-mc-flooding Whether the stop-unreg-mc-flooding feature is on or off

(set with the platform stop-unreg-mc-flooding

command). This feature prevents flooding of unregistered

multicast packets in the occasional situations in which

IGMP snooping does not prevent it.

Vlan-stacking TPID The value of the TPID set in the Ethernet type field when a

frame has a double VLAN tag.

613-50137-01 Rev A Command Reference for FS980M Series 385

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW PLATFORM CLASSIFIER STATISTICS UTILIZATION BRIEF

show platform classifier statistics utilization

brief

Overview This command displays the number of used entries available for various platform

functions, and the percentage that number of entries represents of the total

available.

Syntax show platform classifier statistics utilization brief

Mode Privileged Exec

Example To display the platform classifier utilization statistics, use the following command:

awplus# show platform classifier statistics utilization brief

Output Figure 12-8: Output from the show platform classifier statistics utilization

brief command

Commands

show platform

awplus#show platform classifier statistics utilization brief



[Instance 4]

Number of Entries:

Policy Type Group ID Used / Total

----------------------------------------------

ACL 1476395010 0 / 245 ( 0%)

DoS Inactive 0 / 0 ( 0%)

VLAN Counter

Group-Octet Inactive 0 / 0 ( 0%)

Group-Packet Inactive 0 / 0 ( 0%)

QoS 0 / 768 ( 0%)

613-50137-01 Rev A Command Reference for FS980M Series 386

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW PLATFORM PORT

show platform port

Overview This command displays the various port registers or platform counters for

specified switchports.

Syntax show platform port [<port-list>|counters]

Mode Privileged Exec

Examples To display port registers for port1.0.1 and port1.0.2 use the following command:

awplus# show platform port port1.0.1-port1.0.2

To display platform counters for port1.0.1 and port1.0.2 use the following

command:

awplus# show platform port port1.0.1-port1.0.2 counters

Parameter Description

<port-list> The ports to display information about. A port-list can be:

• a continuous range of ports separated by a hyphen, e.g.

port1.0.1-1.0.6

• a comma-separated list of ports and port ranges, e.g.

port1.0.1,port1.0.4-1.0.6.

counters Show the platform counters.

613-50137-01 Rev A Command Reference for FS980M Series 387

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW PLATFORM PORT

Output Figure 12-9: Example output from the show platform port command

awplus#show platform port port1.0.1

Phy register value for port1.0.1 (ifindex: 5001)



BCM84858 PHY detected



PMA/PMD Registers - Device 1

0=2040 1=0082 2=600d 3=8562

4=0071 5=009b 6=c000 7=0009

8=9701 9=0000 a=0000 b=00a4

e=0000 f=0000



10GBASE-T Registers - Device 1

81=0000 82=0003 83=4800 84=0000

85=8000 86=8000 87=8000 88=8000

89=8000 8a=8000 8b=8000 8c=8000

8d=8000 8e=8000 8f=8000 90=8000

91=0000 92=0000 93=0011 a89e=ffff

a89f=0000 a8a0=0000 a8a9=0000 a8aa=0000

a8ab=0000 a8ac=0000 a8ad=0000

.

Port configuration for lport 0x08002002:

Phy Driver: 8481 10-Gigabit PHY Driver

enabled: 1

loopback: 0

link: 0

speed: 0 max speed: 10000

duplex: 1

linkscan: 1

autonegotiate: 1

master: 2

tx pause: 0 rx pause: 0

untagged vlan: 1

...

Table 6: Parameters in the output from the show platform port command

Parameter Description

Ethernet MAC counters

Combined receive/

transmit packets by

size (octets) counters

Number of packets in each size range received and

transmitted.

64 Number of 64 octet packets received and

transmitted.

65 - 127 Number of 65 - 127 octet packets received and

transmitted.

613-50137-01 Rev A Command Reference for FS980M Series 388

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW PLATFORM PORT

128 - 255 Number of 128 - 255 octet packets received and

transmitted.

256 - 511 Number of 256 - 511 octet packets received and

transmitted.

512 - 1023 Number of 512 - 1023 octet packets received and

transmitted.

1024 - MaxPktSz Number of packets received and transmitted with

size 1024 octets to the maximum packet length.

1519 - 1522 Number of 1519 - 1522 octet packets received and

transmitted.

1519 - 2047 Number of 1519 - 2047 octet packets received and

transmitted.

2048 - 4095 Number of 2048 - 4095 octet packets received and

transmitted.

4096 - 9216 Number of 4096 - 9216 octet packets received and

transmitted.

General Counters

Receive Counters for traffic received.

Octets Number of octets received.

Pkts Number of packets received.

FCSErrors Number of FCS (Frame Check Sequence) error

events received.

UnicastPkts Number of unicast packets received.

MulticastPkts Number of multicast packets received.

BroadcastPkts Number of broadcast packets received.

PauseMACCtlFrms Number of Pause MAC Control Frames received.

OversizePkts Number of oversize packets received.

Fragments Number of fragments received.

Jabbers Number of jabber frames received.

UnsupportOpcode Number of MAC Control frames with unsupported

opcode received.

AlignmentErrors Receive Alignment Error Frame Counter.

Table 6: Parameters in the output from the show platform port command

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 389

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW PLATFORM PORT

SysErDurCarrier Receive Code Error Counter.

CarrierSenseErr Receive False Carrier Counter.

UndersizePkts Number of undersized packets received.

Transmit Counters for traffic transmitted.

Octets Number of octets transmitted.

Pkts Number of packets transmitted.

UnicastPkts Number of unicast packets transmitted.

MulticastPkts Number of multicast packets transmitted.

BroadcastPkts Number of broadcast packets transmitted.

PauseMACCtlFrms Number of Pause MAC Control Frames transmitted.

OversizePkts Number of oversize packets transmitted.

FrameWDeferrdTx Transmit Single Deferral Frame counter.

FrmWExcesDefer Transmit Multiple Deferral Frame counter.

SingleCollsnFrm Transmit Single Collision Frame counter.

MultCollsnFrm Transmit Multiple Collision Frame counter.

LateCollisions Transmit Late Collision Frame counter.

ExcessivCollsns Transmit Excessive Collision Frame counter.

Collisions Transmit Total Collision counter

Layer 3 Counters

ifInUcastPkts Inbound interface Unicast counter.

ifInDiscards Inbound interface Discarded Packets counter.

ipInHdrErrors Inbound interface Header Errors counter.

ifOutUcastPkts Outbound interface Unicast counter.

ifOutErrors Outbound interface Error counter.

Miscellaneous Counters

DropEvents Drop Event counter

Table 6: Parameters in the output from the show platform port command

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 390

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW PLATFORM PORT

ifOutDiscards Outbound interface Discarded Packets counter.

MTUExcdDiscard Receive MTU Check Error Frame Counter

Table 6: Parameters in the output from the show platform port command

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 391

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW PORT-SECURITY INTERFACE

show port-security interface

Overview Use this command to show the current port-security configuration and the switch

port status.

Syntax show port-security interface <port>

Mode Privileged Exec

Example To see the port-security status on port1.0.1, use the following command:

awplus# show port-security interface port1.0.1

Output Figure 12-10: Example output from the show port-security interface command

Commands

clear port-security intrusion

show port-security intrusion

switchport port-security

switchport port-security aging

switchport port-security maximum

switchport port-security violation

Parameter Description

<port> The port to display information about. The port may be a switch

port (e.g. port1.0.4), a static channel group (e.g. sa3), or a

dynamic (LACP) channel group (e.g. po4).

Port Security configuration

Security Enabled : YES

Port Status : ENABLED

Violation Mode : TRAP

Aging : OFF

Maximum MAC Addresses : 3

Total MAC ddresses : 1

Lock Status : UNLOCKED

Security Violation Count : 0

Last Violation Source Address : None

613-50137-01 Rev A Command Reference for FS980M Series 392

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW PORT-SECURITY INTRUSION

show port-security intrusion

Overview Use this command to show the intrusion list. If the port is not specified, the entire

intrusion table is shown.

Syntax show port-security intrusion [interface <port>]

Mode Privileged Exec

Example To see the intrusion list on port1.0.1, use the following command:

awplus# show port-security intrusion interface port1.0.1

Output Figure 12-11: Example output from the show port-security intrusion command

for port 1.0.1

Commands

clear port-security intrusion

show port-security interface

switchport port-security

switchport port-security aging

switchport port-security maximum

switchport port-security violation

Parameter Description

interface Specify a port

<port>The port to display information about. The port may be a switch

port (e.g. port1.0.4), a static channel group (e.g. sa3), or a

dynamic (LACP) channel group (e.g. po4).

Port Security Intrusion List 

Interface: port1.0.1 -3 intrusion(s) detected 

11-22-33-44-55-04 11-22-33-44-55-06 11-22-33-44-55-08

613-50137-01 Rev A Command Reference for FS980M Series 393

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SHOW STORM-CONTROL

show storm-control

Overview Use this command to display storm-control information for all interfaces or a

particular interface.

Syntax show storm-control [<port>]

Mode User Exec and Privileged Exec

Example To display storm-control information for port1.0.2, use the following command:

awplus# show storm-control port1.0.2

Output Figure 12-12: Example output from the show storm-control command for

port1.0.2

Commands

storm-control level

Parameter Description

<port>The port to display information about. The port may be a switch port

(e.g. port1.0.4), a static channel group (e.g. sa2), or a dynamic (LACP)

channel group (e.g. po2).

Port BcastLevel McastLevel DlfLevel

port1.0.2 40. 0% 100. 0% 100. 0%

613-50137-01 Rev A Command Reference for FS980M Series 394

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SPEED

speed

Overview This command changes the speed of the specified port. You can optionally specify

the speed or speeds that get autonegotiated, so autonegotiation is only

attempted at the specified speeds.

To see the currently-negotiated speed for ports whose links are up, use the show

interface command. To see the configured speed (when different from the

default), use the show running-config command.

Syntax speed {10|100|1000|auto [10][100][1000]}

The following table shows the speed options for each type of port.

Mode Interface Configuration

Default By default, ports autonegotiate speed.

Usage Switch ports in a static or dynamic (LACP) channel group must have the same port

speed and be in full duplex mode. Once switch ports have been aggregated into a

channel group, you can set the speed of all the switch ports in the channel group

by applying this command to the channel group.

NOTE: If multiple speeds are specified after the auto option to autonegotiate speeds,

then the device only attempts autonegotiation at those specified speeds.

Examples To set an SFP to a fixed speed of 1000Mbps, enter the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.49

awplus(config-if)# speed 1000

To return the port to auto-negotiating its speed, enter the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.49

awplus(config-if)# speed auto

Port type Speed Options (units are Mbps)

RJ-45 copper ports auto (default)

100

100Mbps fiber SFPs 100

1000Mbps fiber SFPs auto (default)

1000

613-50137-01 Rev A Command Reference for FS980M Series 395

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SPEED

To set the port to auto-negotiate its speed at 1000Mbps only, enter the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.49

awplus(config-if)# speed auto 1000

Commands

duplex

polarity

show interface

speed (asyn)

613-50137-01 Rev A Command Reference for FS980M Series 396

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

STORM-CONTROL LEVEL

storm-control level

Overview Use this command to specify the speed limiting level for broadcasting, multicast,

or destination lookup failure (DLF) traffic for the port. Storm-control limits the

selected traffic type to the specified percentage of the maximum port speed.

Use the no variant of this command to disable storm-control for broadcast,

multicast or DLF traffic.

Syntax storm-control {broadcast|multicast|dlf} level <level>

no storm-control {broadcast|multicast|dlf} level

Default By default, storm-control is disabled.

Mode Interface Configuration

Usage Flooding techniques are used to block the forwarding of unnecessary flooded

traffic. A packet storm occurs when a large number of broadcast packets are

received on a port. Forwarding these packets can cause the network to slow down

or time out.

Example To limit broadcast traffic on port1.0.2 to 30% of the maximum port speed, use the

following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# storm-control broadcast level 30

Commands

show storm-control

Parameter Description

<level> <0-100> Specifies the percentage of the maximum port speed

allowed for broadcast, multicast or destination lookup failure traffic.

broadcast Applies the storm-control to broadcast frames.

multicast Applies the storm-control to multicast frames.

dlf Applies the storm-control to destination lookup failure traffic.

613-50137-01 Rev A Command Reference for FS980M Series 397

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SWITCHPORT PORT-SECURITY

switchport port-security

Overview Use this command to enable the port-security feature. This feature is also known

as the port-based learn limit. It allows the user to set the maximum number of MAC

addresses that each port can learn.

Use the no variant of this command to disable the port-security feature.

Syntax switchport port-security

no switchport port-security

Mode Interface Configuration

Examples To enable the port-security feature on port1.0.4, use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# switchport port-security

To disable the port-security feature on port1.0.4, use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# no switchport port-security

Commands

clear port-security intrusion

show port-security interface

show port-security intrusion

switchport port-security aging

switchport port-security maximum

switchport port-security violation

613-50137-01 Rev A Command Reference for FS980M Series 398

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SWITCHPORT PORT-SECURITY AGING

switchport port-security aging

Overview Use this command to set MAC addresses that have been learned by port security

to age out.

Use the no variant of this command to set the MAC addresses to not age out.

Syntax switchport port-security aging

no switchport port-security aging

Mode Interface Configuration

Examples To set port1.0.4 so that the MAC addresses that have been learned by port security

age out, use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# switchport port-security aging

To stop the MAC addresses that have been learned by port security from aging out

on port1.0.4, use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# no switchport port-security aging

Commands

clear port-security intrusion

show port-security interface

show port-security intrusion

switchport port-security

switchport port-security maximum

switchport port-security violation

613-50137-01 Rev A Command Reference for FS980M Series 399

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SWITCHPORT PORT-SECURITY MAXIMUM

switchport port-security maximum

Overview Use this command to set the maximum number of MAC addresses that each port

can learn.

Use the no variant of this command to unset the maximum number of MAC

addresses that each port can learn. This is same as setting the maximum number

to 0. This command also resets the intrusion list table.

If a new MAC is seen on a port with port security enabled and the MAC is statically

configured for another port, a violation is triggered. The maximum learn limit will

be ignored and the specified intrusion action for the port will be carried out.

Syntax switchport port-security maximum <0-256>

no switchport port-security maximum

Mode Interface Configuration

Examples To learn 3 MAC addresses on port1.0.4, use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# switchport port-security maximum 3

To remove the MAC learning limit on port1.0.4, use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# no switchport port-security maximum

Commands

clear port-security intrusion

show port-security interface

show port-security intrusion

switchport port-security

switchport port-security aging

switchport port-security violation

Parameter Description

maximum <0-256> Specify the maximum number of addresses to learn.

613-50137-01 Rev A Command Reference for FS980M Series 400

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

SWITCHPORT PORT-SECURITY VIOLATION

switchport port-security violation

Overview Use this command to set the action taken on a switch port when the port exceeds

the learning limits. The port action can be either shutdown, restrict or protect. If

shutdown is set, the physical link will be disabled and “shutdown” will be shown

in the config. If restrict is set, the packet from the un-authorized MAC will be

discarded and SNMP TRAP will be generated to alert management. If protect is set,

the packet will simply be discarded by the packet processor silently.

Use the no variant of this command to set the violation action to default. The

default violation action is protect.

Syntax switchport port-security violation {shutdown|restrict|protect}

no switchport port-security violation

Mode Interface Configuration

Examples To set the action to be shutdown on port1.0.4, use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# switchport port-security violation shutdown

To set the port-security action to the default (protect) on port1.0.4, use the

following commands:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# no switchport port-security violation

Commands

clear port-security intrusion

show port-security interface

show port-security intrusion

switchport port-security

switchport port-security aging

switchport port-security maximum

Parameter Description

shutdown Disable the port.

restrict Alert the network administrator.

protect Discard the packet.

613-50137-01 Rev A Command Reference for FS980M Series 401

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

THRASH-LIMITING

thrash-limiting

Overview To block all traffic on a vlan, use the following command:

awplus# configure terminal

awplus(config)# thrash-limiting action vlan-disable

To set the thrash limiting timeout to 5 seconds, use the following command:

awplus(config-if)# thrash-limiting timeout 5

To set the thrash limiting action to its default, use the following command:

awplus(config-if)# no thrash-limiting action

To set the thrash limiting timeout to its default, use the following command:

awplus(config-if)# no thrash-limiting timeout

Commands

loop-protection loop-detect

loop-protection action

loop-protection timeout

show loop-protection

613-50137-01 Rev A Command Reference for FS980M Series 402

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

UNDEBUG LOOPPROT

undebug loopprot

Overview This command applies the functionality of the no debug loopprot command.

613-50137-01 Rev A Command Reference for FS980M Series 403

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SWITCHING COMMANDS

UNDEBUG PLATFORM PACKET

undebug platform packet

Overview This command applies the functionality of the no debug platform packet

command.

613-50137-01 Rev A Command Reference for FS980M Series 404

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN Commands

Introduction

Overview This chapter provides an alphabetical reference of commands used to configure

VLANs. For more information see the VLAN Feature Overview and Configuration

Guide.

Command List •“private-vlan” on page 406

•“private-vlan association” on page 407

•“show vlan” on page 408

•“show vlan classifier group” on page 409

•“show vlan classifier group interface” on page 410

•“show vlan classifier interface group” on page 411

•“show vlan classifier rule” on page 412

•“show vlan private-vlan” on page 413

•“switchport access vlan” on page 414

•“switchport enable vlan” on page 415

•“switchport mode access” on page 416

•“switchport mode private-vlan” on page 417

•“switchport mode private-vlan trunk promiscuous” on page 418

•“switchport mode private-vlan trunk secondary” on page 420

•“switchport mode trunk” on page 422

•“switchport private-vlan host-association” on page 423

•“switchport private-vlan mapping” on page 424

•“switchport trunk allowed vlan” on page 425

•“switchport trunk native vlan” on page 428

613-50137-01 Rev A Command Reference for FS980M Series 405

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

•“switchport voice dscp” on page 429

•“switchport voice vlan” on page 430

•“switchport voice vlan priority” on page 432

•“vlan” on page 433

•“vlan classifier activate” on page 434

•“vlan classifier group” on page 435

•“vlan classifier rule ipv4” on page 436

•“vlan classifier rule proto” on page 437

•“vlan database” on page 440

•“vlan mode stack-local-vlan” on page 441

613-50137-01 Rev A Command Reference for FS980M Series 406

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

PRIVATE-VLAN

private-vlan

Overview Use this command to a create a private VLAN. Private VLANs can be either primary

or secondary. Secondary VLANs can be ether community or isolated.

Use the no variant of this command to remove the specified private VLAN.

For more information, see the VLAN Feature Overview and Configuration Guide.

Syntax private-vlan <vlan-id> {community|isolated|primary}

no private-vlan <vlan-id> {community|isolated|primary}

Mode VLAN Configuration

Examples awplus# configure terminal

awplus(config)# vlan database

awplus(config-vlan)# vlan 2 name vlan2 state enable

awplus(config-vlan)# vlan 3 name vlan3 state enable

awplus(config-vlan)# vlan 4 name vlan4 state enable

awplus(config-vlan)# private-vlan 2 primary

awplus(config-vlan)# private-vlan 3 isolated

awplus(config-vlan)# private-vlan 4 community

awplus# configure terminal

awplus(config)# vlan database

awplus(config-vlan)# no private-vlan 2 primary

awplus(config-vlan)# no private-vlan 3 isolated

awplus(config-vlan)# no private-vlan 4 community

Parameter Description

<vlan-id>VLAN ID in the range <2-4094> for the VLAN which is to be made a

private VLAN.

community Community VLAN.

isolated Isolated VLAN.

primary Primary VLAN.

613-50137-01 Rev A Command Reference for FS980M Series 407

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

PRIVATE-VLAN ASSOCIATION

private-vlan association

Overview Use this command to associate a secondary VLAN to a primary VLAN. Only one

isolated VLAN can be associated to a primary VLAN. Multiple community VLANs

can be associated to a primary VLAN.

Use the no variant of this command to remove association of all the secondary

VLANs to a primary VLAN.

For more information, see the VLAN Feature Overview and Configuration Guide.

Syntax private-vlan <primary-vlan-id> association {add

<secondary-vlan-id>|remove <secondary-vlan-id>}

no private-vlan <primary-vlan-id> association

Mode VLAN Configuration

Examples The following commands associate primary VLAN 2 with secondary VLAN 3:

awplus# configure terminal

awplus(config)# vlan database

awplus(config-vlan)# private-vlan 2 association add 3

The following commands remove the association of primary VLAN 2 with

secondary VLAN 3:

awplus# configure terminal

awplus(config)# vlan database

awplus(config-vlan)# private-vlan 2 association remove 3

The following commands remove all secondary VLAN associations of primary

VLAN 2:

awplus# configure terminal

awplus(config)# vlan database

awplus(config-vlan)# no private-vlan 2 association

Parameter Description

<primary-vlan-id>VLAN ID of the primary VLAN.

<secondary-vlan-id>VLAN ID of the secondary VLAN

(either isolated or community).

613-50137-01 Rev A Command Reference for FS980M Series 408

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SHOW VLAN

show vlan

Overview Use this command to display information about a particular VLAN by specifying its

VLAN ID. Selecting all will display information for all the VLANs configured.

Syntax show vlan

{all|brief|dynamic|static|auto|static-ports|<1-4094>}

Mode User Exec and Privileged Exec

Example To display information about VLAN 2, use the command:

awplus# show vlan 2

Output Figure 13-1: Example output from the show vlan command

Commands

vlan

Parameter Description

<1-4094> Display information about the VLAN specified by the VLAN ID.

all Display information about all VLANs on the device.

brief Display information about all VLANs on the device.

dynamic Display information about all VLANs learned dynamically.

static Display information about all statically configured VLANs.

auto Display information about all auto-configured VLANs.

static-ports Display static egress/forbidden ports.

VLAN ID Name Type State Member ports

(u)-Untagged, (t)-Tagged

======= ================ ======= ======= ====================================

2 VLAN0002 STATIC ACTIVE port1.0.3(u) port1.0.4(u) port1.0.5(u)

port1.0.6(u)

...

613-50137-01 Rev A Command Reference for FS980M Series 409

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SHOW VLAN CLASSIFIER GROUP

show vlan classifier group

Overview Use this command to display information about all configured VLAN classifier

groups or a specific group.

Syntax show vlan classifier group [<1-16>]

Mode User Exec and Privileged Exec

Usage If a group ID is not specified, all configured VLAN classifier groups are shown. If a

group ID is specified, a specific configured VLAN classifier group is shown.

Example To display information about VLAN classifier group 1, enter the command:

awplus# show vlan classifier group 1

Commands

vlan classifier group

Parameter Description

<1-16> VLAN classifier group identifier

613-50137-01 Rev A Command Reference for FS980M Series 410

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SHOW VLAN CLASSIFIER GROUP INTERFACE

show vlan classifier group interface

Overview Use this command to display information about a single switch port interface for

all configured VLAN classifier groups.

Syntax show vlan classifier group interface <switch-port>

Mode User Exec and Privileged Exec

Usage All configured VLAN classifier groups are shown for a single interface.

Example To display VLAN classifier group information for switch port interface port1.0.2,

enter the command:

awplus# show vlan classifier group interface port1.0.2

Output Figure 13-2: Example output from the show vlan classifier group interface

port1.0.1 command:

Commands

vlan classifier group

show vlan classifier interface group

Parameter Description

<switch-port> Specify the switch port interface classifier group identifier

vlan classifier group 1 interface port1.0.1

613-50137-01 Rev A Command Reference for FS980M Series 411

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SHOW VLAN CLASSIFIER INTERFACE GROUP

show vlan classifier interface group

Overview Use this command to display information about all interfaces configured for a

VLAN group or all the groups.

Syntax show vlan classifier interface group [<1-16>]

Mode User Exec and Privileged Exec

Usage If a group ID is not specified, all interfaces configured for all VLAN classifier groups

are shown. If a group ID is specified, the interfaces configured for this VLAN

classifier group are shown.

Example To display information about all interfaces configured for all VLAN groups, enter

the command:

awplus# show vlan classifier interface group

To display information about all interfaces configured for VLAN group 1, enter the

command:

awplus# show vlan classifier interface group 1

Output Figure 13-3: Example output from the show vlan classifier interface group

command

Output Figure 13-4: Example output from the show vlan classifier interface group 1

command

Commands

vlan classifier group

show vlan classifier group interface

Parameter Description

<1-16> VLAN classifier interface group identifier

vlan classifier group 1 interface port1.0.1

vlan classifier group 1 interface port1.0.2

vlan classifier group 2 interface port1.0.3

vlan classifier group 2 interface port1.0.4

vlan classifier group 1 interface port1.0.1

vlan classifier group 1 interface port1.0.2

613-50137-01 Rev A Command Reference for FS980M Series 412

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SHOW VLAN CLASSIFIER RULE

show vlan classifier rule

Overview Use this command to display information about all configured VLAN classifier rules

or a specific rule.

Syntax show vlan classifier rule [<1-256>]

Mode User Exec and Privileged Exec

Usage If a rule ID is not specified, all configured VLAN classifier rules are shown. If a rule ID

is specified, a specific configured VLAN classifier rule is shown.

Example To display information about VLAN classifier rule 1, enter the command:

awplus# show vlan classifier rule 1

Output Figure 13-5: Example output from the show vlan classifier rule1 command

Commands

vlan classifier activate

vlan classifier rule ipv4

vlan classifier rule proto

Parameter Description

<1-256> VLAN classifier rule identifier

vlan classifier group 1 add rule 1

613-50137-01 Rev A Command Reference for FS980M Series 413

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SHOW VLAN PRIVATE-VLAN

show vlan private-vlan

Overview Use this command to display the private VLAN configuration and associations.

Syntax show vlan private-vlan

Mode User Exec and Privileged Exec

Example To display the private VLAN configuration and associations, enter the command:

awplus# show vlan private-vlan

Output Figure 13-6: Example output from the show vlan private-vlan command

Commands

private-vlan

private-vlan association

awplus#show vlan private-vlan

PRIMARY SECONDARY TYPE INTERFACES

------- --------- ---------- ----------

2 3 isolated

2 4 community

8 isolated

613-50137-01 Rev A Command Reference for FS980M Series 414

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT ACCESS VLAN

switchport access vlan

Overview Use this command to change the port-based VLAN of the current port.

Use the no variant of this command to change the port-based VLAN of this port to

the default VLAN, vlan1.

Syntax switchport access vlan <vlan-id>

no switchport access vlan

Default Reset the default VLAN 1 to specified switchports using the negated form of this

command.

Mode Interface Configuration

Usage Any untagged frame received on this port will be associated with the specified

VLAN.

Examples To change the port-based VLAN to VLAN 3 for port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# switchport access vlan 3

To reset the port-based VLAN to the default VLAN 1 for port1.0.2, use the

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no switchport access vlan

Commands

show interface switchport

show vlan

Parameter Description

<vlan-id><1-4094> The port-based VLAN ID for the port.

613-50137-01 Rev A Command Reference for FS980M Series 415

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT ENABLE VLAN

switchport enable vlan

Overview This command enables the VLAN on the port manually once disabled by certain

actions, such as QSP (QoS Storm Protection) or EPSR (Ethernet Protection

Switching Ring). Note that if the VID is not given, all disabled VLANs are re-enabled.

This command enables the VLAN on the port manually once disabled by certain

actions, such as EPSR (Ethernet Protection Switching Ring). Note that if the VID is

not given, all disabled VLANs are re-enabled.

Syntax switchport enable vlan [<1-4094>]

Mode Interface Configuration

Example To re-enable the port1.0.1 from VLAN 1:

awplus# configure terminal

awplus(config)# interface port1.0.1

awplus(config-if)# switchport enable vlan 1

Commands

show mls qos interface storm-status

storm-window

Parameter Description

vlan Re-enables the VLAN on the port.

<1-4094> VLAN ID.

613-50137-01 Rev A Command Reference for FS980M Series 416

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT MODE ACCESS

switchport mode access

Overview Use this command to set the switching characteristics of the port to access mode.

Received frames are classified based on the VLAN characteristics, then accepted or

discarded based on the specified filtering criteria.

Syntax switchport mode access [ingress-filter {enable|disable}]

Default By default, ports are in access mode with ingress filtering on.

Usage Use access mode to send untagged frames only.

Mode Interface Configuration

Example awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# switchport mode access ingress-filter enable

Validation

Command

show interface switchport

Parameter Description

ingress-filter Set the ingress filtering for the received frames.

enable Turn on ingress filtering for received frames. This is the default.

disable Turn off ingress filtering to accept frames that do not meet the

classification criteria.

613-50137-01 Rev A Command Reference for FS980M Series 417

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT MODE PRIVATE-VLAN

switchport mode private-vlan

Overview Use this command to make a Layer 2 port a private VLAN host port or a

promiscuous port.

Use the no variant of this command to remove the configuration.

Syntax switchport mode private-vlan {host|promiscuous}

no switchport mode private-vlan {host|promiscuous}

Mode Interface Configuration

Examples awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# switchport mode private-vlan host

awplus(config)# interface port1.0.3

awplus(config-if)# switchport mode private-vlan promiscuous

awplus(config)# interface port1.0.4

awplus(config-if)# no switchport mode private-vlan promiscuous

Commands

switchport private-vlan mapping

Parameter Description

host This port type can communicate with all other host ports assigned to

the same community VLAN, but it cannot communicate with the

ports in the same isolated VLAN. All communications outside of this

VLAN must pass through a promiscuous port in the associated

primary VLAN.

promiscuous A promiscuous port can communicate with all interfaces, including

the community and isolated ports within a private VLAN.

613-50137-01 Rev A Command Reference for FS980M Series 418

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT MODE PRIVATE-VLAN TRUNK PROMISCUOUS

switchport mode private-vlan trunk

promiscuous

Overview Use this command to enable a port in trunk mode to be promiscuous port for

isolated VLANs.

Use the no variant of this command to remove a port in trunk mode as a

promiscuous port for isolated VLANs. You must first remove the secondary port, or

ports, in trunk mode associated with the promiscuous port with the no switchport

mode private-vlan trunk secondary command.

Syntax switchport mode private-vlan trunk promiscuous group <group-id>

no switchport mode private-vlan trunk promiscuous

Default By default, a port in trunk mode is disabled as a promiscuous port.

Mode Interface Configuration

Usage A port must be put in trunk mode with switchport mode trunk command before it

can be enabled as a promiscuous port.

To add VLANs to be trunked over the promiscuous port, use the switchport trunk

allowed vlan command. These VLANs can be isolated VLANs, or non-private VLANs.

To configure the native VLAN for the promiscuous port, use the switchport trunk

native vlan command. The native VLAN can be an isolated VLAN, or a non-private

VLAN.

When you enable a promiscuous port, all of the secondary port VLANs associated

with the promiscuous port via the group ID number must be added to the

promiscuous port. In other words, the set of VLANs on the promiscuous port must

be a superset of all the VLANs on the secondary ports within the group.

Parameter Description

<group-id>The group ID is a numeric value in the range 1 to 32 that is

used to associate the promiscuous port with secondary ports.

613-50137-01 Rev A Command Reference for FS980M Series 419

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT MODE PRIVATE-VLAN TRUNK PROMISCUOUS

Examples To create the isolated VLANs 2, 3 and 4 and then enable port1.0.2 in trunk

mode as a promiscuous port for these VLANs with the group ID of 3, use the

following commands:

awplus# configure terminal

awplus(config)# vlan database

awplus(config-vlan)# vlan 2-4

awplus(config-vlan)# private-vlan 2 isolated

awplus(config-vlan)# private-vlan 3 isolated

awplus(config-vlan)# private-vlan 4 isolated

awplus(config-vlan)# exit

awplus(config)# interface port1.0.2

awplus(config-if)# switchport mode trunk

awplus(config-if)# switchport trunk allowed vlan add 2-4

awplus(config-if)# switchport mode private-vlan trunk

promiscuous group 3

To remove port1.0.2 in trunk mode as a promiscuous port for a private VLAN, use

the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no switchport mode private-vlan trunk

promiscuous

Note that you must remove the secondary port or ports enabled as trunk ports that

are associated with the promiscuous port before removing the promiscuous port.

Commands

switchport mode private-vlan trunk secondary

switchport mode trunk

switchport trunk allowed vlan

switchport trunk native vlan

show vlan private-vlan

613-50137-01 Rev A Command Reference for FS980M Series 420

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT MODE PRIVATE-VLAN TRUNK SECONDARY

switchport mode private-vlan trunk

secondary

Overview Use this command to enable a port in trunk mode to be a secondary port for

isolated VLANs.

Use the no variant of this command to remove a port in trunk mode as a secondary

port for isolated VLANs.

Syntax switchport mode private-vlan trunk secondary group <group-id>

no switchport mode private-vlan trunk secondary

Default By default, a port in trunk mode is disabled as a secondary port.

When a port in trunk mode is enabled to be a secondary port for isolated VLANs,

by default it will have a native VLAN of none(no native VLAN specified).

Mode Interface Configuration

Usage A port must be put in trunk mode with switchport mode trunk command before

the port is enabled as a secondary port in trunk mode.

To add VLANs to be trunked over the secondary port use the switchport trunk

allowed vlan command. These must be isolated VLANs and must exist on the

associated promiscuous port.

To configure the native VLAN for the secondary port, use the switchport trunk

native vlan command. The native VLAN must be an isolated VLAN and must exist

on the associated promiscuous port.

Parameter Description

<group-id>The group ID is a numeric value in the range 1 to 32 that is

used to associate a secondary port with its promiscuous port.

613-50137-01 Rev A Command Reference for FS980M Series 421

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT MODE PRIVATE-VLAN TRUNK SECONDARY

Examples To create isolated private VLAN 2 and then enable port1.0.3 in trunk mode as

a secondary port for the this VLAN with the group ID of 3, use the following

commands:

awplus# configure terminal

awplus(config)# vlan database

awplus(config-vlan)# vlan 2

awplus(config-vlan)# private-vlan 2 isolated

awplus(config-vlan)# exit

awplus(config)# interface port1.0.3

awplus(config-if)# switchport mode trunk

awplus(config-if)# switchport trunk allowed vlan add 2

awplus(config-if)# switchport mode private-vlan trunk secondary

group 3

To remove port1.0.3 in trunk mode as a secondary port, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.3

awplus(config-if)# no switchport mode private-vlan trunk

secondary

Commands

switchport mode private-vlan trunk promiscuous

switchport mode trunk

switchport trunk allowed vlan

switchport trunk native vlan

show vlan private-vlan

613-50137-01 Rev A Command Reference for FS980M Series 422

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT MODE TRUNK

switchport mode trunk

Overview Use this command to set the switching characteristics of the port to trunk.

Received frames are classified based on the VLAN characteristics, then accepted or

discarded based on the specified filtering criteria.

Syntax switchport mode trunk [ingress-filter {enable|disable}]

Default By default, ports are in access mode, are untagged members of the default VLAN

(vlan1), and have ingress filtering on.

Mode Interface Configuration

Usage A port in trunk mode can be a tagged member of multiple VLANs, and an untagged

member of one native VLAN.

To configure which VLANs this port will trunk for, use the switchport trunk allowed

vlan command.

Example awplus# configure terminal

awplus(config)# interface port1.0.3

awplus(config-if)# switchport mode trunk ingress-filter enable

Validation

Command

show interface switchport

Parameter Description

ingress-filter Set the ingress filtering for the frames received.

enable Turn on ingress filtering for received frames. This is the default.

disable Turn off ingress filtering to accept frames that do not meet the

classification criteria.

613-50137-01 Rev A Command Reference for FS980M Series 423

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT PRIVATE-VLAN HOST-ASSOCIATION

switchport private-vlan host-association

Overview Use this command to associate a primary VLAN and a secondary VLAN to a host

port. Only one primary and secondary VLAN can be associated to a host port.

Use the no variant of this command to remove the association.

Syntax switchport private-vlan host-association <primary-vlan-id> add

<secondary-vlan-id>

no switchport private-vlan host-association

Mode Interface Configuration

Examples awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# switchport private-vlan host-association 2

add 3

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no switchport private-vlan host-association

Parameter Description

<primary-vlan-id>VLAN ID of the primary VLAN.

<secondary-vlan-id>VLAN ID of the secondary VLAN (either isolated or com

munity).

613-50137-01 Rev A Command Reference for FS980M Series 424

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT PRIVATE-VLAN MAPPING

switchport private-vlan mapping

Overview Use this command to associate a primary VLAN and a set of secondary VLANs to a

promiscuous port.

Use the no variant of this to remove all the association of secondary VLANs to

primary VLANs for a promiscuous port.

Syntax switchport private-vlan mapping <primary-vlan-id> add

<secondary-vid-list>

switchport private-vlan mapping <primary-vlan-id> remove

<secondary-vid-list>

no switchport private-vlan mapping

Mode Interface Configuration

Usage This command can be applied to a switch port or a static channel group, but not a

dynamic (LACP) channel group. LACP channel groups (dynamic/LACP

aggregators) cannot be promiscuous ports in private VLANs.

Examples awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# switchport private-vlan mapping 2 add 3-4

awplus(config-if)# switchport private-vlan mapping 2 remove 3-4

awplus(config-if)# no switchport private-vlan mapping

Commands

switchport mode private-vlan

Parameter Description

<primary-vlan-id>VLAN ID of the primary VLAN.

<secondary-vid-list>VLAN ID of the secondary VLAN (either isolated or

community), or a range of VLANs, or a comma-separated

list of VLANs and ranges.

613-50137-01 Rev A Command Reference for FS980M Series 425

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT TRUNK ALLOWED VLAN

switchport trunk allowed vlan

Overview Use this command to add VLANs to be trunked over this switch port. Traffic for

these VLANs can be sent and received on the port.

Use the no variant of this command to reset switching characteristics of a specified

interface to negate a trunked configuration specified with switchport trunk

allowed vlan command.

Syntax switchport trunk allowed vlan all

switchport trunk allowed vlan none

switchport trunk allowed vlan add <vid-list>

switchport trunk allowed vlan remove <vid-list>

switchport trunk allowed vlan except <vid-list>

no switchport trunk

Default By default, ports are untagged members of the default VLAN (vlan1).

Mode Interface Configuration

Usage The all parameter sets the port to be a tagged member of all the VLANs configured

on the device. The none parameter removes all VLANs from the port’s tagged

member set. The add and remove parameters will add and remove VLANs to and

from the port’s member set. See the note below about restrictions when using the

add, remove, except, and all parameters.

NOTE: Only use the add or the remove parameters with this command if a list of

VLANs are configured on a port. Only use the except parameter to remove VLANs after

Parameter Description

all Allow all VLANs to transmit and receive through the port.

none Allow no VLANs to transmit and receive through the port.

add Add a VLAN to transmit and receive through the port. Only use this

parameter if a list of VLANs are already configured on a port.

remove Remove a VLAN from transmit and receive through the port. Only use

this parameter if a list of VLANs are already configured on a port.

except All VLANs, except the VLAN for which the VID is specified, are part of

its port member set. Only use this parameter to remove VLANs after

either this parameter or the all parameter have added VLANs to a

port.

<vid-list>For a VLAN range, specify two VLAN numbers: lowest, then highest

number in the range, separated by a hyphen.

For a VLAN list, specify the VLAN numbers separated by commas.

Do not enter spaces between hyphens or commas when setting

parameters for VLAN ranges or lists.

613-50137-01 Rev A Command Reference for FS980M Series 426

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT TRUNK ALLOWED VLAN

either the except or the all parameters have first been used to add a list of VLANs to a

port.

To remove a VLAN, where the configuration for port1.0.6 shows the below

output:

Remove VLAN 3 by re-entering the except parameter with the list of VLANs to

remove, instead of using the remove parameter, as shown in the command

example below:

awplus# configure terminal

awplus(config)# interface port1.0.6

awplus(config-if)# switchport trunk allowed vlan except 3,4

Then the configuration is changed after entering the above commands to remove

VLAN 3:

To add a VLAN, where the configuration for port1.0.6 shows the below output:

awplus#show running-config



!

interface port1.0.6

switchport

switchport mode trunk

switchport trunk allowed vlan except 4

awplus#show running-config



!



interface port1.0.6

switchport

switchport mode trunk

switchport trunk allowed vlan except 3-4

awplus#show running-config



!



interface port1.0.6

switchport

switchport mode trunk

switchport trunk allowed vlan except 3-5

613-50137-01 Rev A Command Reference for FS980M Series 427

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT TRUNK ALLOWED VLAN

Add VLAN 4 by re-entering the except parameter with a list of VLANs to exclude,

instead of using the add parameter to include VLAN 4, as shown in the command

example below:

awplus# configure terminal

awplus(config)# interface port1.0.5

awplus(config-if)# switchport trunk allowed vlan except 3,5

The configuration is changed after entering the above commands to add VLAN 4:

Examples The following shows adding a single VLAN to the port’s member set.

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# switchport trunk allowed vlan add 2

The following shows adding a range of VLANs to the port’s member set.

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# switchport trunk allowed vlan add 2-4

The following shows adding a list of VLANs to the port’s member set.

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# switchport trunk allowed vlan add 2,3,4

awplus#show running-config



!



interface port1.0.5

switchport

switchport mode trunk

switchport trunk allowed vlan except 3,5

613-50137-01 Rev A Command Reference for FS980M Series 428

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT TRUNK NATIVE VLAN

switchport trunk native vlan

Overview Use this command to configure the native VLAN for this port. The native VLAN is

used for classifying the incoming untagged packets. Use the none parameter with

this command to remove the native VLAN from the port and set the acceptable

frame types to vlan-tagged only.

Use the no variant of this command to revert the native VLAN to the default VLAN

ID 1. Command negation removes tagged VLANs, and sets the native VLAN to the

default VLAN.

Syntax switchport trunk native vlan {<vid>|none}

no switchport trunk native vlan

Default VLAN 1 (the default VLAN), which is reverted to using the no form of this

command.

Mode Interface Configuration

Examples The following commands show configuration of VLAN 2 as the native VLAN for

port1.0.2:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# switchport trunk native vlan 2

The following commands show the removal of the native VLAN for interface

port1.0.2:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# switchport trunk native vlan none

The following commands revert the native VLAN to the default VLAN 1 for interface

port1.0.2:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no switchport trunk native vlan

Parameter Description

<vid>The ID of the VLAN that will be used to classify the incoming

untagged packets, in the range 2-2094. The VLAN ID must be a part of

the VLAN member set of the port.

none No native VLAN specified. This option removes the native VLAN from

the port and sets the acceptable frame types to vlan-tagged only.

Note: Use the no variant of this command to revert to the default

VLAN 1 as the native VLAN for the specified interface switchport - not

none.

613-50137-01 Rev A Command Reference for FS980M Series 429

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT VOICE DSCP

switchport voice dscp

Overview Use this command for a specific port to configure the Layer 3 DSCP value

advertised when the transmission of LLDP-MED Network Policy TLVs for voice

devices is enabled. When LLDP-MED capable IP phones receive this network policy

information, they transmit voice data with the specified DSCP value.

Use the no variant of this command to reset the DSCP value to the default, 0.

Syntax switchport voice dscp <0-63>

no switchport voice dscp

Default A DSCP value of 0 will be advertised.

Mode Interface Configuration

Usage LLDP-MED advertisements including Network Policy TLVs are transmitted via a

port if:

•LLDP is enabled (lldp run command)

• Voice VLAN is configured for the port (switchport voice vlan command)

• The port is configured to transmit LLDP advertisements—enabled by default

(lldp transmit receive command)

• The port is configured to transmit Network Policy TLVs—enabled by default

(lldp med-tlv-select command)

• There is an LLDP-MED device connected to the port

Example To tell IP phones connected to port1.0.5 to send voice data with DSCP value 27,

use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.5

awplus(config-if)# switchport voice dscp 27

Commands

lldp med-tlv-select

show lldp

switchport voice vlan

Parameter Description

dscp Specify a DSCP value for voice data.

<0-63>DSCP value.

613-50137-01 Rev A Command Reference for FS980M Series 430

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT VOICE VLAN

switchport voice vlan

Overview Use this command to configure the Voice VLAN tagging advertised when the

transmission of LLDP-MED Network Policy TLVs for voice endpoint devices is

enabled. When LLDP-MED capable IP phones receive this network policy

information, they transmit voice data with the specified tagging. This command

also sets the ports to be spanning tree edge ports, that is, it enables spanning tree

portfast on the ports.

Use the no variant of this command to remove LLDP-MED network policy

configuration for voice devices connected to these ports. This does not change the

spanning tree edge port status.

Syntax switchport voice vlan [<vid>|dot1p|dynamic|untagged]

no switchport voice vlan

Default By default, no Voice VLAN is configured, and therefore no network policy is

advertised for voice devices.

Mode Interface Configuration

Usage LLDP-MED advertisements including Network Policy TLVs are transmitted via a

port if:

•LLDP is enabled (lldp run command)

• Voice VLAN is configured for the port using this command (switchport voice

vlan)

• The port is configured to transmit LLDP advertisements—enabled by default

(lldp transmit receive command)

• The port is configured to transmit Network Policy TLVs—enabled by default

(lldp med-tlv-select command)

• There is an LLDP-MED device connected to the port.

To set the priority value to be advertised for tagged frames, use the switchport

voice vlan priority command.

If the Voice VLAN details are to be assigned by RADIUS, then the RADIUS server

must be configured to send the attribute “Egress-VLANID (56)” or

Parameter Description

dot1p The IP phone should send User Priority tagged packets, that is, packets in

which the tag contains a User Priority value, and a VID of 0. (The User

Priority tag is also known as the 802.1p priority tag, or the Class of Service

(CoS) tag.)

dynamic The VLAN ID with which the IP phone should send tagged packets will be

assigned by RADIUS authentication.

untagged The IP phone should send untagged packets.

613-50137-01 Rev A Command Reference for FS980M Series 431

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT VOICE VLAN

“Egress-VLAN-Name (58)” in the RADIUS Accept message when authenticating a

phone attached to this port.

For more information about configuring authentication for Voice VLAN, see the

LLDP Feature Overview and Configuration Guide.

If the ports have been set to be edge ports by the switchport voice vlan command,

the no variant of this command will leave them unchanged as edge ports. To set

them back to their default non-edge port configuration, use the spanning-tree

edgeport (RSTP and MSTP) command.

Examples To tell IP phones connected to port1.0.5 to send voice data tagged for VLAN

10, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.5

awplus(config-if)# switchport voice vlan 10

To tell IP phones connected to ports 1.0.2-1.0.6 to send priority tagged packets

(802.1p priority tagged with VID 0, so that they will be assigned to the port VLAN)

use the following commands. The priority value is 5 by default, but can be

configured with the switchport voice vlan priority command.

awplus# configure terminal

awplus(config)# interface port1.0.2-port1.0.6

awplus(config-if)# switchport voice vlan dot1p

To dynamically configure the VLAN ID advertised to IP phones connected to

port1.0.1 based on the VLAN assigned by RADIUS authentication (with RADIUS

attribute “Egress- VLANID” or “Egress-VLAN-Name” in the RADIUS accept packet),

use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.1

awplus(config-if)# switchport voice vlan dynamic

To remove the Voice VLAN, and therefore disable the transmission of LLDP-MED

network policy information for voice devices on port1.0.6, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.6

awplus(config-if)# no switchport voice vlan

613-50137-01 Rev A Command Reference for FS980M Series 432

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

SWITCHPORT VOICE VLAN PRIORITY

switchport voice vlan priority

Overview Use this command to configure the Layer 2 user priority advertised when the

transmission of LLDP-MED Network Policy TLVs for voice devices is enabled. This is

the priority in the User Priority field of the IEEE 802.1Q VLAN tag, also known as the

Class of Service (CoS), or 802.1p priority. When LLDP-MED capable IP phones

receive this network policy information, they transmit voice data with the specified

priority.

Syntax switchport voice vlan priority <0-7>

no switchport voice vlan priority

Default By default, the Voice VLAN user priority value is 5.

Mode Interface Configuration

Usage LLDP-MED advertisements including Network Policy TLVs are transmitted via a

port if:

•LLDP is enabled (lldp run command)

• Voice VLAN is configured for the port (switchport voice vlan command)

• The port is configured to transmit LLDP advertisements—enabled by default

(lldp transmit receive command)

• The port is configured to transmit Network Policy TLVs—enabled by default

(lldp med-tlv-select command)

• There is an LLDP-MED device connected to the port.

To set the Voice VLAN tagging to be advertised, use the switchport voice vlan

command.

Example To remove the Voice VLAN, and therefore disable the transmission of LLDP-MED

network policy information for voice devices on port1.0.6, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.6

awplus(config-if)# no switchport voice vlan

Commands

lldp med-tlv-select

show lldp

switchport voice vlan

Parameter Description

priority Specify a user priority value for voice data.

<0-7>Priority value.

613-50137-01 Rev A Command Reference for FS980M Series 433

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

VLAN

vlan

Overview This command creates VLANs, assigns names to them, and enables or disables

them. Disabling the VLAN causes all forwarding over the specified VLAN ID to

cease. Enabling the VLAN allows forwarding of frames on the specified VLAN.

When VCStack is enabled, you can configure a maximum of 512 VLANs.

The no variant of this command destroys the specified VLANs or returns their MTU

to the default.

Syntax vlan <vid> [name <vlan-name>] [state {enable|disable}]

vlan <vid-range> [state {enable|disable}]

vlan {<vid>|<vlan-name>} [mtu <mtu-value>]

no vlan {<vid>|<vid-range>} [mtu]

Default By default, VLANs are enabled when they are created.

Mode VLAN Configuration

Examples To enable vlan 45, use the commands:

awplus# configure terminal

awplus(config)# vlan database

awplus(config-vlan)# vlan 45 name accounts state enable

To destroy vlan 45, use the commands:

awplus# configure terminal

awplus(config)# vlan database

awplus(config-vlan)# no vlan 45

Commands

mtu

vlan database

show vlan

Parameter Description

<vid>The VID of the VLAN to enable or disable, in the range 1-4094.

<vlan-name>The ASCII name of the VLAN. Maximum length: 32 characters.

<vid-range>Specifies a range of VLAN identifiers.

<mtu-value>Specifies the Maximum Transmission Unit (MTU) size in bytes, in the

range 68 to 1500 bytes, for the VLAN.

enable Puts the VLAN into an enabled state.

disable Puts the VLAN into a disabled state.

613-50137-01 Rev A Command Reference for FS980M Series 434

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

VLAN CLASSIFIER ACTIVATE

vlan classifier activate

Overview Use this command in Interface Configuration mode to associate a VLAN classifier

group with the switch port.

Use the no variant of this command to remove the VLAN classifier group from the

switch port.

Syntax vlan classifier activate <vlan-class-group-id>

no vlan classifier activate <vlan-class-group-id>

Mode Interface Configuration mode for a switch port or link aggregator.

Usage See the protocol-based VLAN configuration example in the VLAN Feature

Overview and Configuration Guide for configuration details.

Example To associate VLAN classifier group 3 with switch port1.0.3, enter the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.3

awplus(config-if)# vlan classifier activate 3

To remove VLAN classifier group 3 from switch port1.0.3, enter the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.3

awplus(config-if)# no vlan classifier activate 3

Commands

show vlan classifier rule

vlan classifier group

vlan classifier rule ipv4

vlan classifier rule proto

Parameter Description

<vlan-class-group-id>Specify a VLAN classifier group identifier in the range

<1-16>.

613-50137-01 Rev A Command Reference for FS980M Series 435

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

VLAN CLASSIFIER GROUP

vlan classifier group

Overview Use this command to create a group of VLAN classifier rules. The rules must already

have been created.

Use the no variant of this command to delete a group of VLAN classifier rules.

Syntax vlan classifier group <1-16> {add|delete} rule

<vlan-class-rule-id>

no vlan classifier group <1-16>

Mode Global Configuration

Example awplus# configure terminal

awplus(config)# vlan classifier group 3 add rule 5

Commands

show vlan classifier rule

vlan classifier activate

vlan classifier rule ipv4

vlan classifier rule proto

Parameter Description

<1-16> VLAN classifier group identifier

add Add the rule to the group.

delete Delete the rule from the group.

<vlan-class-rule-id> The VLAN classifier rule identifier.

613-50137-01 Rev A Command Reference for FS980M Series 436

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

VLAN CLASSIFIER RULE IPV4

vlan classifier rule ipv4

Overview Use this command to create an IPv4 subnet-based VLAN classifier rule and map it

to a specific VLAN. Use the no variant of this command to delete the VLAN classifier

rule.

Syntax vlan classifier rule <1-256> ipv4 <ip-addr/prefix-length> vlan

<1-4094>

no vlan classifier rule <1-256>

Mode Global Configuration

Usage If the source IP address matches the IP subnet specified in the VLAN classifier rule,

the received packets are mapped to the specified VLAN.

NOTE: The subnet VLAN classifier only matches IPv4 packets. It does not match ARP

packets. To ensure ARP traffic is classified into the correct subnet VLAN, you can use a

hardware based policy map that sends ARP packets to the CPU, which will then process

them appropriately. This means that if you use subnet-based VLANs, you should also

configure the following:

NOTE: The policy map should be applied to each port that uses a subnet based VLAN

using the service-policy input command:

Example awplus# configure terminal

awplus(config)# vlan classifier rule 3 ipv4 3.3.3.3/8 vlan 5

Commands

show vlan classifier rule

vlan classifier activate

vlan classifier rule proto

Parameter Description

<1-256>Specify the VLAN Classifier Rule identifier.

<ip-addr/prefix-length> Specify the IP address and prefix length.

<1-4094>Specify a VLAN ID to which an untagged packet is

mapped in the range <1-4094>.

613-50137-01 Rev A Command Reference for FS980M Series 437

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

VLAN CLASSIFIER RULE PROTO

vlan classifier rule proto

Overview Use this command to create a protocol type-based VLAN classifier rule, and map it

to a specific VLAN. See the published IANA EtherType IEEE 802 numbers here:

www.iana.org/assignments/ieee-802-numbers/ieee-802-numbers.txt.

Instead of a protocol name the decimal value of the protocol's EtherType can be

entered. The EtherType field is a two-octet field in an Ethernet frame. It is used to

show which protocol is encapsulated in the payload of the Ethernet frame. Note

that EtherTypes in the IANA 802 numbers are given as hexadecimal values.

The no variant of this command removes a previously set rule.

Syntax vlan classifier rule <1-256> proto <protocol> encap

{ethv2|nosnapllc|snapllc} vlan <1-4094>

no vlan classifier rule <1-256>

Parameter Description

<1-256> VLAN Classifier identifier

proto Protocol type

<protocol> Specify a protocol either by its decimal number (0-65535) or by one

of the following protocol names:

[arp|2054] Address Resolution

protocol

[atalkaarp|33011] Appletalk AARP protocol

[atalkddp|32923] Appletalk DDP protocol

[atmmulti|34892] MultiProtocol Over ATM

protocol

[atmtransport|34948] Frame-based ATM

Transport protocol

[dec|24576] DEC Assigned protocol

[deccustom|24582] DEC Customer use

protocol

[decdiagnostics|24581] DEC Systems Comms

Arch protocol

[decdnadumpload|24577] DEC DNA Dump/Load

protocol

[decdnaremoteconsole|24578] DEC DNA Remote

Console protocol

[decdnarouting|24579] DEC DNA Routing

protocol

[declat|24580] DEC LAT protocol

613-50137-01 Rev A Command Reference for FS980M Series 438

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

VLAN CLASSIFIER RULE PROTO

Mode Global Configuration

Usage If the protocol type matches the protocol specified in the VLAN classifier rule, the

received packets are mapped to the specified VLAN. Ethernet Frame Numbers may

be entered in place of the protocol names listed. For a full list please refer to the

IANA list online:

www.iana.org/assignments/ieee-802-numbers/ieee-802-numbers.txt

[decsyscomm|24583] DEC Systems Comms

Arch protocol

[g8bpqx25|2303] G8BPQ AX.25 protocol

[ieeeaddrtrans|2561] Xerox IEEE802.3 PUP

Address

[ieeepup|2560] Xerox IEEE802.3 PUP

protocol

[ip|2048] IP protocol

[ipv6|34525] IPv6 protocol

[ipx|33079] IPX protocol

[netbeui|61680] IBM NETBIOS/NETBEUI

protocol

[netbeui|61681] IBM NETBIOS/NETBEUI

protocol

[pppdiscovery|34915] PPPoE discovery protocol

[pppsession|34916] PPPoE session protocol

[rarp|32821] Reverse Address

Resolution protocol

[x25|2056] CCITT.25 protocol

[xeroxaddrtrans|513] Xerox PUP Address

Translation protocol

[xeroxpup|512] Xerox PUP protocol

ethv2 Ethernet Version 2 encapsulation

<1-4094> Specify a VLAN ID to which an untagged packet is mapped in the

range <1-4094>

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 439

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

VLAN CLASSIFIER RULE PROTO

Example awplus# configure terminal

awplus(config)# vlan classifier rule 1 proto x25 encap ethv2

vlan 2

awplus(config)# vlan classifier rule 2 proto 512 encap ethv2

vlan 2

awplus(config)# vlan classifier rule 3 proto 2056 encap ethv2

vlan 2

awplus(config)# vlan classifier rule 4 proto 2054 encap ethv2

vlan 2

Validation

Output

awplus# show vlan classifier rule

Commands

show vlan classifier rule

vlan classifier activate

vlan classifier group

vlan classifier rule 16 proto rarp encap ethv2 vlan 2



vlan classifier rule 8 proto encap ethv2 vlan 2



vlan classifier rule 4 proto arp encap ethv2 vlan 2



vlan classifier rule 3 proto xeroxpup encap ethv2 vlan 2

vlan classifier rule 2 proto ip encap ethv2 vlan 2

vlan classifier rule 1 proto ipv6 encap ethv2 vlan 2

613-50137-01 Rev A Command Reference for FS980M Series 440

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

VLAN DATABASE

vlan database

Overview Use this command to enter the VLAN Configuration mode.

Syntax vlan database

Mode Global Configuration

Usage Use this command to enter the VLAN configuration mode. You can then add or

delete a VLAN, or modify its values.

Example In the following example, note the change to VLAN configuration mode from

Configure mode:

awplus# configure terminal

awplus(config)# vlan database

awplus(config-vlan)#

Commands

vlan

613-50137-01 Rev A Command Reference for FS980M Series 441

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

VLAN MODE STACK-LOCAL-VLAN

vlan mode stack-local-vlan

Overview This command enables you to create stack-local-VLANs and use ICMP to monitor

and diagnose issues within specific members of the stack. When a VLAN is added

using this method, all its traffic will be trapped to and processed by the CPU of the

specific local stack member, rather than the CPU of the stack master.

The no variant of this command destroys the specified VLAN.

Syntax vlan <vid> mode stack-local-vlan <member-id>

no vlan <vid>

Default By default, VLANs are automatically enabled as they are added.

Mode VLAN Configuration

Usage If IGMP snooping is operating on a stack-local-VLAN, the device will try to process

some multicast traffic via that VLAN, if it is connected to a Microsoft Windows PC.

To avoid this, we recommend disabling IGMP snooping on stack-local-VLANs, by

using the command no ip igmp snooping.

Examples To add a stack-local-VLAN with the VID of 4002 and assign it to stack member 2, use

the following commands:

awplus# configure terminal

awplus(config)# vlan database

awplus(config-vlan)# vlan 4002 mode stack-local-vlan 2

awplus(config-vlan)# exit

awplus(config)# interface vlan4002

awplus(config-if)# no ip igmp snooping

Parameter Description

<vid>The VID of the VLAN to be created in the range 2-4094. We

recommend that the first stack-local-vlan be assigned the

number 4001 for the first stack member, then incremented

by one for each stack member. For example, a stack of four

members would be assigned the following VID numbers:

• stack member one: VID 4001

• stack member two: VID 4002

• stack member three: VID 4003

• stack member four: VID 4004

mode stack-local-

vlan

Specifies that the new VLAN will function as a stack-local-

VLAN.

<member-id>Specifies the new stack member ID. Enter a decimal number

in the range 1-8.

613-50137-01 Rev A Command Reference for FS980M Series 442

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

VLAN COMMANDS

VLAN MODE STACK-LOCAL-VLAN

To remove VLAN 4002, use the following commands:

awplus# configure terminal

awplus(config)# vlan database

awplus(config-vlan)# no vlan 4002

Commands

ip igmp snooping

mtu

vlan database

613-50137-01 Rev A Command Reference for FS980M Series 443

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Spanning Tree

Commands

Introduction

Overview This chapter provides an alphabetical reference for commands used to configure

RSTP, STP or MSTP. For information about spanning trees, including configuration

procedures, see the STP Feature Overview and Configuration Guide.

Command List •“clear spanning-tree statistics” on page 445

•“clear spanning-tree detected protocols (RSTP and MSTP)” on page 446

•“debug mstp (RSTP and STP)” on page 447

•“instance priority (MSTP)” on page 451

•“instance vlan (MSTP)” on page 453

•“region (MSTP)” on page 455

•“revision (MSTP)” on page 456

•“show debugging mstp” on page 457

•“show spanning-tree” on page 458

•“show spanning-tree brief” on page 461

•“show spanning-tree mst” on page 462

•“show spanning-tree mst config” on page 463

•“show spanning-tree mst detail” on page 464

•“show spanning-tree mst detail interface” on page 466

•“show spanning-tree mst instance” on page 468

•“show spanning-tree mst instance interface” on page 469

•“show spanning-tree mst interface” on page 470

•“show spanning-tree mst detail interface” on page 471

•“show spanning-tree statistics” on page 473

613-50137-01 Rev A Command Reference for FS980M Series 444

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

•“show spanning-tree statistics instance” on page 475

•“show spanning-tree statistics instance interface” on page 476

•“show spanning-tree statistics interface” on page 478

•“show spanning-tree vlan range-index” on page 480

•“spanning-tree autoedge (RSTP and MSTP)” on page 481

•“spanning-tree bpdu” on page 482

•“spanning-tree cisco-interoperability (MSTP)” on page 484

•“spanning-tree edgeport (RSTP and MSTP)” on page 485

•“spanning-tree enable” on page 486

•“spanning-tree errdisable-timeout enable” on page 488

•“spanning-tree errdisable-timeout interval” on page 489

•“spanning-tree force-version” on page 490

•“spanning-tree forward-time” on page 491

•“spanning-tree guard root” on page 492

•“spanning-tree hello-time” on page 493

•“spanning-tree link-type” on page 494

•“spanning-tree max-age” on page 495

•“spanning-tree max-hops (MSTP)” on page 496

•“spanning-tree mode” on page 497

•“spanning-tree mst configuration” on page 498

•“spanning-tree mst instance” on page 499

•“spanning-tree mst instance path-cost” on page 500

•“spanning-tree mst instance priority” on page 502

•“spanning-tree mst instance restricted-role” on page 503

•“spanning-tree mst instance restricted-tcn” on page 505

•“spanning-tree path-cost” on page 506

•“spanning-tree portfast (STP)” on page 507

•“spanning-tree portfast bpdu-filter” on page 509

•“spanning-tree portfast bpdu-guard” on page 511

•“spanning-tree priority (bridge priority)” on page 513

•“spanning-tree priority (port priority)” on page 514

•“spanning-tree restricted-role” on page 515

•“spanning-tree restricted-tcn” on page 516

•“

spanning-tree transmit-holdcount” on page 517

•“undebug mstp” on page 518

613-50137-01 Rev A Command Reference for FS980M Series 445

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

CLEAR SPANNING-TREE STATISTICS

clear spanning-tree statistics

Overview Use this command to clear all the STP BPDU (Bridge Protocol Data Unit) statistics.

Syntax clear spanning-tree statistics

clear spanning-tree statistics [instance <mstp-instance>]

clear spanning-tree statistics [interface <port> [instance

<mstp-instance>]]

Mode User Exec and Privileged Exec

Usage Use this command with the instance parameter in MSTP mode. Specifying this

command with the interface parameter only not the instance parameter will work

in STP and RSTP mode.

Examples awplus# clear spanning-tree statistics

awplus# clear spanning-tree statistics instance 1

awplus# clear spanning-tree statistics interface port1.0.2

instance 1

Parameter Description

<port>The port to clear STP BPDU statistics for. The port may be a switch

port (e.g. port1.0.4), a static channel group (e.g. sa2), or a

dynamic (LACP) channel group (e.g. po2).

<mstp-

instance>

The MSTP instance (MSTI - Multiple Spanning Tree Instance) to clear

MSTP BPDU statistics.

613-50137-01 Rev A Command Reference for FS980M Series 446

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

CLEAR SPANNING-TREE DETECTED PROTOCOLS (RSTP AND MSTP)

clear spanning-tree detected protocols

(RSTP and MSTP)

Overview Use this command to clear the detected protocols for a specific port, or all ports.

Use this command in RSTP or MSTP mode only.

Syntax clear spanning-tree detected protocols [interface <port>]

Mode Privileged Exec

Example awplus# clear spanning-tree detected protocols

Parameter Description

<port>The port to clear detected protocols for. The port may be a switch

port (e.g. port1.0.4), a static channel group (e.g. sa2), or a

dynamic (LACP) channel group (e.g. po2).

613-50137-01 Rev A Command Reference for FS980M Series 447

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

DEBUG MSTP (RSTP AND STP)

debug mstp (RSTP and STP)

Overview Use this command to enable debugging for the configured spanning tree mode,

and echo data to the console, at various levels. Note that although this command

uses the keyword mstp it displays debugging output for RSTP and STP protocols

as well the MSTP protocol.

Use the no variant of this command to disable spanning tree debugging.

Syntax debug mstp {all|cli|protocol [detail]|timer [detail]}

debug mstp {packet {rx|tx} [decode] [interface <interface>]}

debug mstp {topology-change [interface <interface>]}

no debug mstp {all|cli|protocol [detail]|timer [detail]}

no debug mstp {packet {rx|tx} [decode] [interface <interface>]}

no debug mstp {topology-change [interface <interface>]}

Mode Privileged Exec and Global Configuration mode

Usage 1 Use the debug mstp topology-change interface command to generate

debugging messages when the device receives an indication of a topology change

in a BPDU from another device. The debugging can be activated on a per-port

basis. Although this command uses the keyword mstp, it displays debugging

output for RSTP and STP protocols as well as the MSTP protocol.

Due to the likely volume of output, these debug messages are best viewed using

the terminal monitor command before issuing the relevant debug mstp

Parameter Description

all Echoes all spanning tree debugging levels to the console.

cli Echoes spanning tree commands to the console.

packet Echoes spanning tree packets to the console.

rx Received packets.

tx Transmitted packets.

protocol Echoes protocol changes to the console.

timer Echoes timer information to the console.

detail Detailed output.

decode Interprets packet contents

topology-change Interprets topology change messages

interface Keyword before <interface> placeholder to specify an

interface to debug

<interface>Placeholder used to specify the name of the interface to

debug.

613-50137-01 Rev A Command Reference for FS980M Series 448

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

DEBUG MSTP (RSTP AND STP)

command. The default terminal monitor filter will select and display these

messages. Alternatively, the messages can be directed to any of the other log

outputs by adding a filter for the MSTP application using log buffered (filter)

command:

awplus# configure terminal

awplus(config)# log buffered program mstp

Output 1

Usage 2 Use the debug mstp packet rx|tx decode interface command to generate

debugging messages containing the entire contents of a BPDU displayed in

readable text for transmitted and received xSTP BPDUs. The debugging can be

activated on a per-port basis and transmit and receive debugging is controlled

independently. Although this command uses the keyword mstp, it displays

debugging output for RSTP and STP protocols as well as the MSTP protocol.

Due to the likely volume of output, these debug messages are best viewed using

the terminal monitor command before issuing the relevant debug mstp

command. The default terminal monitor filter will select and display these

messages. Alternatively, the messages can be directed to any of the other log

outputs by adding a filter for the MSTP application using the log buffered (filter)

command:

awplus(config)# log buffered program mstp

Output 2 In MSTP mode - an MSTP BPDU with 1 MSTI:

awplus#terminal monitor

awplus#debug mstp topology-change interface port1.0.4

10:09:09 awplus MSTP[1409]: Topology change rcvd on port1.0.4 (internal)

10:09:09 awplus MSTP[1409]: Topology change rcvd on MSTI 1 port1.0.4

aawplus#debug mstp topology-change interface port1.0.6

10:09:29 awplus MSTP[1409]: Topology change rcvd on port1.0.6 (external)

10:09:29 awplus MSTP[1409]: Topology change rcvd on MSTI 1 port1.0.6

613-50137-01 Rev A Command Reference for FS980M Series 449

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

DEBUG MSTP (RSTP AND STP)

In STP mode transmitting a TCN BPDU:

In STP mode receiving an STP BPDU:

In RSTP mode receiving an RSTP BPDU:

awplus#terminal monitor

awplus#debug mstp packet rx decode interface port1.0.4

17:23:42 awplus MSTP[1417]: port1.0.4 xSTP BPDU rx - start

17:23:42 awplus MSTP[1417]: Protocol version: MSTP, BPDU type: RST

17:23:42 awplus MSTP[1417]: CIST Flags: Agree Forward Learn role=Desig

17:23:42 awplus MSTP[1417]: CIST root id : 0000:0000cd1000fe

17:23:42 awplus MSTP[1417]: CIST ext pathcost : 0

17:23:42 awplus MSTP[1417]: CIST reg root id : 0000:0000cd1000fe

17:23:42 awplus MSTP[1417]: CIST port id : 8001 (128:1)

17:23:42 awplus MSTP[1417]: msg age: 0 max age: 20 hellotime: 2 fwd delay: 15

17:23:42 awplus MSTP[1417]: Version 3 length : 80

17:23:42 awplus MSTP[1417]: Format id : 0

17:23:42 awplus MSTP[1417]: Config name : test

17:23:42 awplus MSTP[1417]: Revision level : 0

17:23:42 awplus MSTP[1417]: Config digest : 3ab68794d602fdf43b21c0b37ac3bca8

17:23:42 awplus MSTP[1417]: CIST int pathcost : 0

17:23:42 awplus MSTP[1417]: CIST bridge id : 0000:0000cd1000fe

17:23:42 awplus MSTP[1417]: CIST hops remaining : 20

17:23:42 awplus MSTP[1417]: MSTI flags : Agree Forward Learn role=Desig

17:23:42 awplus MSTP[1417]: MSTI reg root id : 8001:0000cd1000fe

17:23:42 awplus MSTP[1417]: MSTI pathcost : 0

17:23:42 awplus MSTP[1417]: MSTI bridge priority : 32768 port priority : 128

17:23:42 awplus MSTP[1417]: MSTI hops remaining : 20

17:23:42 awplus MSTP[1417]: port1.0.4 xSTP BPDU rx - finish

awplus#terminal monitor

awplus#debug mstp packet tx decode interface port1.0.4

17:28:09 awplus MSTP[1417]: port1.0.4 xSTP BPDU tx - start

17:28:09 awplus MSTP[1417]: Protocol version: STP, BPDU type: TCN

17:28:09 awplus MSTP[1417]: port1.0.4 xSTP BPDU tx - finish

awplus#terminal monitor

awplus#debug mstp packet rx decode interface port1.0.4

17:31:36 awplus MSTP[1417]: port1.0.4 xSTP BPDU rx - start

17:31:36 awplus MSTP[1417]: Protocol version: STP, BPDU type: Config

17:31:36 awplus MSTP[1417]: Flags: role=none

17:31:36 awplus MSTP[1417]: Root id : 8000:0000cd1000fe

17:31:36 awplus MSTP[1417]: Root pathcost : 0

17:31:36 awplus MSTP[1417]: Bridge id : 8000:0000cd1000fe

17:31:36 awplus MSTP[1417]: Port id : 8001 (128:1)

17:31:36 awplus MSTP[1417]: msg age: 0 max age: 20 hellotime: 2 fwd delay: 15

17:31:36 awplus MSTP[1417]: ort1.0.4 xSTP BPDU rx - finish



613-50137-01 Rev A Command Reference for FS980M Series 450

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

DEBUG MSTP (RSTP AND STP)

Examples awplus# debug mstp all

awplus# debug mstp cli

awplus# debug mstp packet rx

awplus# debug mstp protocol detail

awplus# debug mstp timer

awplus# debug mstp packet rx decode interface port1.0.2

awplus# debug mstp packet tx decode interface port1.0.6

Commands

log buffered (filter)

show debugging mstp

terminal monitor

undebug mstp

awplus#terminal monitor

awplus#debug mstp packet rx decode interface port1.0.4

awplus#17:30:17 awplus MSTP[1417]: port1.0.4 xSTP BPDU rx - start

17:30:17 awplus MSTP[1417]: Protocol version: RSTP, BPDU type: RST

17:30:17 awplus MSTP[1417]: CIST Flags: Forward Learn role=Desig

17:30:17 awplus MSTP[1417]: CIST root id : 8000:0000cd1000fe

17:30:17 awplus MSTP[1417]: CIST ext pathcost : 0

17:30:17 awplus MSTP[1417]: CIST reg root id : 8000:0000cd1000fe

17:30:17 awplus MSTP[1417]: CIST port id : 8001 (128:1)

17:30:17 awplus MSTP[1417]: msg age: 0 max age: 20 hellotime: 2 fwd delay: 15

17:30:17 awplus MSTP[1417]: port1.0.4 xSTP BPDU rx - finish

613-50137-01 Rev A Command Reference for FS980M Series 451

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

INSTANCE PRIORITY (MSTP)

instance priority (MSTP)

Overview Use this command to set the priority for this device to become the root bridge for

the specified MSTI (Multiple Spanning Tree Instance).

Use this command for MSTP only.

Use the no variant of this command to restore the root bridge priority of the device

for the instance to the default.

Syntax instance <instance-id> priority <priority>

no instance <instance-id> priority

Default The default priority value for all instances is 32768.

Mode MST Configuration

Usage MSTP lets you distribute traffic more efficiently across a network by blocking

different links for different VLANs. You do this by making different devices into the

root bridge for each MSTP instance, so that each instance blocks a different link.

If all devices have the same root bridge priority for the instance, MSTP selects the

device with the lowest MAC address to be the root bridge. Give the device a higher

priority for becoming the root bridge for a particular instance by assigning it a

lower priority number, or vice versa.

Examples To set the root bridge priority for MSTP instance 2 to be the highest (0), so that it

will be the root bridge for this instance when available, use the commands:

awplus# configure terminal

awplus(config)# spanning-tree mst configuration

awplus(config-mst)# instance 2 priority 0

To reset the root bridge priority for instance 2 to the default (32768), use the

commands:

awplus# configure terminal

awplus(config)# spanning-tree mst configuration

awplus(config-mst)# no instance 2 priority

Parameter Description

<instance-id>Specify an MSTP instance in the range 1-5.

<priority> Specify the root bridge priority for the device for the MSTI in the

range <0-61440>. Note that a lower priority number indicates a

greater likelihood of the device becoming the root bridge. The

priority values can be set only in increments of 4096. If you

specify a number that is not a multiple of 4096, it will be rounded

down. The default priority is 32768.

613-50137-01 Rev A Command Reference for FS980M Series 452

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

INSTANCE PRIORITY (MSTP)

Commands

region (MSTP)

revision (MSTP)

show spanning-tree mst config

spanning-tree mst instance

spanning-tree mst instance priority

613-50137-01 Rev A Command Reference for FS980M Series 453

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

INSTANCE VLAN (MSTP)

instance vlan (MSTP)

Overview Use this command to create an MST Instance (MSTI), and associate the specified

VLANs with it. An MSTI is a spanning tree instance that exists within an MST region

(MSTR).

When a VLAN is associated with an MSTI the member ports of the VLAN are

automatically configured to send and receive spanning-tree information for the

associated MSTI. You can disable this automatic configuration of member ports of

the VLAN to the associated MSTI by using a no spanning-tree mst instance

command to remove the member port from the MSTI.

Use the instance vlan command for MSTP only.

Use the no variant of this command to remove the specified VLANs from the MSTI.

Syntax instance <instance-id> vlan <vid-list>

no instance <instance-id> vlan <vid-list>

Mode MST Configuration

Usage The VLANs must be created before being associated with an MST instance (MSTI).

If the VLAN range is not specified, the MSTI will not be created.

This command removes the specified VLANs from the CIST and adds them to the

specified MSTI. If you use the no variant of this command to remove the VLAN from

the MSTI, it returns it to the CIST. To move a VLAN from one MSTI to another, you

must first use the no variant of this command to return it to the CIST.

Ports in these VLANs will remain in the control of the CIST until you associate the

ports with the MSTI using the spanning-tree mst instance command.

Example To associate VLAN 30 with MSTI 2, use the commands:

awplus# configure terminal

awplus(config)# spanning-tree mode mstp

awplus(config)# spanning-tree mst configuration

awplus(config-mst)# instance 2 vlan 30

Parameter Description

<instance-id>Specify an MSTP instance in the range 1-5.

<vid-list> Specify one or more VLAN identifiers (VID) to be associated with

the MSTI specified. This can be a single VID in the range 1-4094,

or a hyphen-separated range or a comma-separated list of VLAN

IDs.

613-50137-01 Rev A Command Reference for FS980M Series 454

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

INSTANCE VLAN (MSTP)

Commands

region (MSTP)

revision (MSTP)

show spanning-tree mst config

spanning-tree mst instance

vlan

613-50137-01 Rev A Command Reference for FS980M Series 455

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

REGION (MSTP)

region (MSTP)

Overview Use this command to assign a name to the device’s MST Region. MST Instances

(MSTI) of a region form different spanning trees for different VLANs.

Use this command for MSTP only.

Use the no variant of this command to remove this region name and reset it to the

default.

Syntax region <region-name>

no region

Default By default, the region name is My Name.

Mode MST Configuration

Usage The region name, the revision number, and the digest of the VLAN to MSTI

configuration table must be the same on all devices that are intended to be in the

same MST region.

Example awplus# configure terminal

awplus(config)# spanning-tree mst configuration

awplus(config-mst)# region ATL

Commands

revision (MSTP)

show spanning-tree mst config

Parameter Description

<region-name>Specify the name of the region, up to 32 characters. Valid

characters are upper-case, lower-case, digits, underscore.

613-50137-01 Rev A Command Reference for FS980M Series 456

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

REVISION (MSTP)

revision (MSTP)

Overview Use this command to specify the MST revision number to be used in the

configuration identifier.

Use this command for MSTP only.

Syntax revision <revision-number>

Default The default of revision number is 0.

Mode MST Configuration

Usage The region name, the revision number, and the digest of the VLAN to MSTI

configuration table must be the same on all devices that are intended to be in the

same MST region.

Example awplus# configure terminal

awplus(config)# spanning-tree mst configuration

awplus(config-mst)# revision 25

Commands

region (MSTP)

show spanning-tree mst config

instance vlan (MSTP)

Parameter Description

<revision-number><0-65535> Revision number.

613-50137-01 Rev A Command Reference for FS980M Series 457

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW DEBUGGING MSTP

show debugging mstp

Overview Use this command to show the MSTP debugging options set.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show debugging mstp

Mode User Exec and Privileged Exec mode

Example To display the MSTP debugging options set, enter the command:

awplus# show debugging mstp

Output Figure 14-1: Example output from show debugging mstp

Commands

debug mstp (RSTP and STP)

MSTP debugging status:

MSTP receiving packet debugging is on

613-50137-01 Rev A Command Reference for FS980M Series 458

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE

show spanning-tree

Overview Use this command to display detailed spanning tree information on the specified

port or on all ports. Use this command for RSTP, MSTP or STP.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show spanning-tree [interface <port-list>]

Mode User Exec and Privileged Exec

Usage Note that any list of interfaces specified must not span any interfaces that are not

installed.

A topology change counter has been included for RSTP and MSTP. You can see the

topology change counter for RSTP by using the show spanning-tree command.

You can see the topology change counter for MSTP by using the show

spanning-tree mst instance command.

Example To display spanning tree information about port1.0.3, use the command:

awplus# show spanning-tree interface port1.0.3

Parameter Description

interface Display information about the following port only.

<port-list>The ports to display information about. A port-list can be:

• a switch port (e.g. port1.0.6) a static channel group (e.g. sa2) or a

dynamic (LACP) channel group (e.g. po2)

• a continuous range of ports separated by a hyphen, e.g.

port1.0.1-1.0.4, or sa1-2, or po1-2

• a comma-separated list of ports and port ranges, e.g.

port1.0.1,port1.0.4-1.0.6. Do not mix switch ports, static channel

groups, and dynamic (LACP) channel groups in the same list

613-50137-01 Rev A Command Reference for FS980M Series 459

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE

Output Figure 14-2: Example output from show spanning-tree in RSTP mode

Output Figure 14-3: Example output from show spanning-tree

awplus#show spanning-tree

% 1: Bridge up - Spanning Tree Enabled

% 1: Root Path Cost 0 - Root Port 0 - Bridge Priority 32768

% 1: Forward Delay 15 - Hello Time 2 - Max Age 20

% 1: Root Id 80000000cd24ff2d

% 1: Bridge Id 80000000cd24ff2d

% 1: last topology change Mon Oct 3 02:06:26 2016

% 1: portfast bpdu-filter disabled

% 1: portfast bpdu-guard disabled

% 1: portfast errdisable timeout disabled

% 1: portfast errdisable timeout interval 300 sec

% port1.0.1: Port 5001 - Id 8389 - Role Disabled - State Discarding

% port1.0.1: Designated Path Cost 0

% port1.0.1: Configured Path Cost 20000000 - Add type Explicit ref count 1

% port1.0.1: Designated Port Id 8389 - Priority 128 -

% port1.0.1: Root 80000000cd24ff2d

% port1.0.1: Designated Bridge 80000000cd24ff2d

% port1.0.1: Message Age 0 - Max Age 20

% port1.0.1: Hello Time 2 - Forward Delay 15

% port1.0.1: Forward Timer 0 - Msg Age Timer 0 - Hello Timer 0 - topo change 

timer 0

% port1.0.1: forward-transitions 0

% port1.0.1: Version Rapid Spanning Tree Protocol - Received None - Send STP

% port1.0.1: No portfast configured - Current portfast off

% port1.0.1: portfast bpdu-guard default - Current portfast bpdu-guard off

% port1.0.1: portfast bpdu-filter default - Current portfast bpdu-filter off

% port1.0.1: no root guard configured - Current root guard off

% port1.0.1: Configured Link Type point-to-point - Current shared

%

% port1.0.2: Port 5002 - Id 838a - Role Disabled - State Discarding

% port1.0.2: Designated Path Cost 0

% port1.0.2: Configured Path Cost 20000000 - Add type Explicit ref count 1

% port1.0.2: Designated Port Id 838a - Priority 128 -

% port1.0.2: Root 80000000cd24ff2d

% port1.0.2: Designated Bridge 80000000cd24ff2d

% port1.0.2: Message Age 0 - Max Age 20

% port1.0.2: Hello Time 2 - Forward Delay 15

% port1.0.2: Forward Timer 0 - Msg Age Timer 0 - Hello Timer 0 - topo change 

timer 0

% port1.0.2: forward-transitions 0

% port1.0.2: Version Rapid Spanning Tree Protocol - Received None - Send STP

% port1.0.2: No portfast configured - Current portfast off

% port1.0.2: portfast bpdu-guard default - Current portfast bpdu-guard off

% port1.0.2: portfast bpdu-filter default - Current portfast bpdu-filter off

% port1.0.2: no root guard configured - Current root guard off

% port1.0.2: Configured Link Type point-to-point - Current shared

613-50137-01 Rev A Command Reference for FS980M Series 460

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE

% 1: Bridge up - Spanning Tree Enabled

% 1: Root Path Cost 0 - Root Port 0 - Bridge Priority 32768

% 1: Forward Delay 15 - Hello Time 2 - Max Age 20

% 1: Root Id 80000000cd20f093

% 1: Bridge Id 80000000cd20f093

% 1: last topology change Mon Oct 3 02:06:26 2016

% 1: portfast bpdu-filter disabled

% 1: portfast bpdu-guard disabled

% 1: portfast errdisable timeout disabled

% 1: portfast errdisable timeout interval 300 sec

% port1.0.3: Port 5023 - Id 839f - Role Designated - State Forwarding

% port1.0.3: Designated Path Cost 0

% port1.0.3: Configured Path Cost 200000 - Add type Explicit ref count 1

% port1.0.3: Designated Port Id 839f - Priority 128 -

% port1.0.3: Root 80000000cd20f093

% port1.0.3: Designated Bridge 80000000cd20f093

% port1.0.3: Message Age 0 - Max Age 20

% port1.0.3: Hello Time 2 - Forward Delay 15

% port1.0.3: Forward Timer 0 - Msg Age Timer 0 - Hello Timer 1 - topo change 

timer 0

% port1.0.3: forward-transitions 32

% port1.0.3: Version Rapid Spanning Tree Protocol - Received None - Send RSTP

% port1.0.3: No portfast configured - Current portfast off

% port1.0.3: portfast bpdu-guard default - Current portfast bpdu-guard off

% port1.0.3: portfast bpdu-filter default - Current portfast bpdu-filter off

% port1.0.3: no root guard configured - Current root guard off

% port1.0.3: Configured Link Type point-to-point - Current point-to-point

...

613-50137-01 Rev A Command Reference for FS980M Series 461

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE BRIEF

show spanning-tree brief

Overview Use this command to display a summary of spanning tree status information on all

ports. Use this command for RSTP, MSTP or STP.

Syntax show spanning-tree brief

Mode User Exec and Privileged Exec

Usage Note that any list of interfaces specified must not span any interfaces that are not

installed.

A topology change counter has been included for RSTP and MSTP. You can see the

topology change counter for RSTP by using the show spanning-tree command.

You can see the topology change counter for MSTP by using the show

spanning-tree mst instance command.

Example To display a summary of spanning tree status information, use the command:

awplus# show spanning-tree brief

Output Figure 14-4: Example output from show spanning-tree brief

Commands

show spanning-tree

Parameter Description

brief A brief summary of spanning tree information.

Default: Bridge up - Spanning Tree Enabled

Default: Root Path Cost 40000 - Root Port 4501 - Bridge Priority 32768

Default: Root Id 8000:0000cd250001

Default: Bridge Id 8000:0000cd296eb1



Port Designated Bridge Port Id Role State

sa1 8000:001577c9744b 8195 Rootport Forwarding

po1 8000:0000cd296eb1 81f9 Designated Forwarding

port1.0.1 8000:0000cd296eb1 8389 Disabled Discarding

port1.0.2 8000:0000cd296eb1 838a Disabled Discarding

port1.0.3 8000:0000cd296eb1 838b Disabled Discarding

...

613-50137-01 Rev A Command Reference for FS980M Series 462

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE MST

show spanning-tree mst

Overview This command displays bridge-level information about the CIST and VLAN to MSTI

mappings.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show spanning-tree mst

Mode User Exec, Privileged Exec and Interface Configuration

Example To display bridge-level information about the CIST and VLAN to MSTI mappings,

enter the command:

awplus# show spanning-tree mst

Output Figure 14-5: Example output from show spanning-tree mst

Commands

show spanning-tree mst interface

% 1: Bridge up - Spanning Tree Enabled

% 1: CIST Root Path Cost 0 - CIST Root Port 0 - CIST Bridge 

Priority 32768

% 1: Forward Delay 15 - Hello Time 2 - Max Age 20 - Max-hops 20

% 1: CIST Root Id 8000000475e93ffe

% 1: CIST Reg Root Id 8000000475e93ffe

% 1: CST Bridge Id 8000000475e93ffe

% 1: portfast bpdu-filter disabled

% 1: portfast bpdu-guard disabled

% 1: portfast errdisable timeout disabled

% 1: portfast errdisable timeout interval 300 sec

%

% Instance VLAN

% 0: 1

% 2: 4

613-50137-01 Rev A Command Reference for FS980M Series 463

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE MST CONFIG

show spanning-tree mst config

Overview Use this command to display MSTP configuration identifier for the device.

Syntax show spanning-tree mst config

Mode User Exec, Privileged Exec and Interface Configuration

Usage The region name, the revision number, and the digest of the VLAN to MSTI

configuration table must be the same on all devices that are intended to be in the

same MST region.

Example To display MSTP configuration identifier information, enter the command:

awplus# show spanning-tree mst config

Output Figure 14-6: Example output from show spanning-tree mst config

Commands

instance vlan (MSTP)

region (MSTP)

revision (MSTP)

awplus#show spanning-tree mst config

%

% MSTP Configuration Information:

%------------------------------------------------------

% Format Id : 0

% Name : My Name

% Revision Level : 0

% Digest : 0x80DEE46DA92A98CF21C603291B22880A

%------------------------------------------------------

613-50137-01 Rev A Command Reference for FS980M Series 464

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE MST DETAIL

show spanning-tree mst detail

Overview This command displays detailed information about each instance, and all

interfaces associated with that particular instance.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show spanning-tree mst detail

Mode User Exec, Privileged Exec and Interface Configuration

Example To display detailed information about each instance, and all interfaces associated

with them, enter the command:

awplus# show spanning-tree mst detail

Output Figure 14-7: Example output from show spanning-tree mst detail

% 1: Bridge up - Spanning Tree Enabled

% 1: CIST Root Path Cost 0 - CIST Root Port 0 - CIST Bridge Priority 32768

% 1: Forward Delay 15 - Hello Time 2 - Max Age 20 - Max-hops 20

% 1: CIST Root Id 80000000cd24ff2d

% 1: CIST Reg Root Id 80000000cd24ff2d

% 1: CIST Bridge Id 80000000cd24ff2d

% 1: portfast bpdu-filter disabled

% 1: portfast bpdu-guard disabled

% 1: portfast errdisable timeout disabled

% 1: portfast errdisable timeout interval 300 sec

% port1.0.1: Port 5001 - Id 8389 - Role Disabled - State Discarding

% port1.0.1: Designated External Path Cost 0 -Internal Path Cost 0

% port1.0.1: Configured Path Cost 20000000 - Add type Explicit ref count 1

% port1.0.1: Designated Port Id 8389 - CIST Priority 128 -

% port1.0.1: CIST Root 80000000cd24ff2d

% port1.0.1: Regional Root 80000000cd24ff2d

% port1.0.1: Designated Bridge 80000000cd24ff2d

% port1.0.1: Message Age 0 - Max Age 20

% port1.0.1: CIST Hello Time 2 - Forward Delay 15

% port1.0.1: CIST Forward Timer 0 - Msg Age Timer 0 - Hello Timer 0 - topo 

change timer 0

...

% port1.0.2: forward-transitions 0

% port1.0.2: Version Multiple Spanning Tree Protocol - Received None - Send STP

% port1.0.2: No portfast configured - Current portfast off

% port1.0.2: portfast bpdu-guard default - Current portfast bpdu-guard off

% port1.0.2: portfast bpdu-filter default - Current portfast bpdu-filter off

% port1.0.2: no root guard configured - Current root guard off

% port1.0.2: Configured Link Type point-to-point - Current shared

613-50137-01 Rev A Command Reference for FS980M Series 465

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE MST DETAIL

% port1.0.3: Port 5003 - Id 838b - Role Disabled - State Discarding

% port1.0.3: Designated External Path Cost 0 -Internal Path Cost 0

% port1.0.3: Configured Path Cost 20000000 - Add type Explicit ref count 1

% port1.0.3: Designated Port Id 838b - CIST Priority 128 -

% port1.0.3: CIST Root 80000000cd24ff2d

% port1.0.3: Regional Root 80000000cd24ff2d

% port1.0.3: Designated Bridge 80000000cd24ff2d

% port1.0.3: Message Age 0 - Max Age 20

% port1.0.3: CIST Hello Time 2 - Forward Delay 15

% port1.0.3: CIST Forward Timer 0 - Msg Age Timer 0 - Hello Timer 0 - topo 

change timer 0

% port1.0.3: forward-transitions 0

% port1.0.3: Version Multiple Spanning Tree Protocol - Received None - Send STP

% port1.0.3: No portfast configured - Current portfast off

% port1.0.3: portfast bpdu-guard default - Current portfast bpdu-guard off

% port1.0.3: portfast bpdu-filter default - Current portfast bpdu-filter off

% port1.0.3: no root guard configured - Current root guard off

% port1.0.3: Configured Link Type point-to-point - Current shared

613-50137-01 Rev A Command Reference for FS980M Series 466

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE MST DETAIL INTERFACE

show spanning-tree mst detail interface

Overview This command displays detailed information about the specified switch port, and

the MST instances associated with it.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show spanning-tree mst detail interface <port>

Mode User Exec, Privileged Exec and Interface Configuration

Example To display detailed information about port1.0.3 and the instances associated

with it, enter the command:

awplus# show spanning-tree mst detail interface port1.0.3

Output Figure 14-8: Example output from show spanning-tree mst detail interface

Parameter Description

<port>The port to display information about. The port may be a switch port

(e.g. port1.0.4), a static channel group (e.g. sa2), or a dynamic

(LACP) channel group (e.g. po2).

% 1: Bridge up - Spanning Tree Enabled

% 1: CIST Root Path Cost 0 - CIST Root Port 0 - CIST Bridge Priority 32768

% 1: Forward Delay 15 - Hello Time 2 - Max Age 20 - Max-hops 20

% 1: CIST Root Id 80000000cd24ff2d

% 1: CIST Reg Root Id 80000000cd24ff2d

% 1: CIST Bridge Id 80000000cd24ff2d

% 1: portfast bpdu-filter disabled

% 1: portfast bpdu-guard disabled

% 1: portfast errdisable timeout disabled

% 1: portfast errdisable timeout interval 300 sec

% port1.0.2: Port 5002 - Id 838a - Role Disabled - State Discarding

% port1.0.2: Designated External Path Cost 0 -Internal Path Cost 0

% port1.0.2: Configured Path Cost 20000000 - Add type Explicit ref count 2

% port1.0.2: Designated Port Id 838a - CIST Priority 128 -

% port1.0.2: CIST Root 80000000cd24ff2d

% port1.0.2: Regional Root 80000000cd24ff2d

% port1.0.2: Designated Bridge 80000000cd24ff2d

% port1.0.2: Message Age 0 - Max Age 20

% port1.0.2: CIST Hello Time 2 - Forward Delay 15

% port1.0.2: CIST Forward Timer 0 - Msg Age Timer 0 - Hello Timer 0 - topo 

change timer 0

% port1.0.2: forward-transitions 0

% port1.0.2: Version Multiple Spanning Tree Protocol - Received None - Send STP

613-50137-01 Rev A Command Reference for FS980M Series 467

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE MST DETAIL INTERFACE

% port1.0.2: No portfast configured - Current portfast off

% port1.0.2: portfast bpdu-guard default - Current portfast bpdu-guard off

% port1.0.2: portfast bpdu-filter default - Current portfast bpdu-filter off

% port1.0.2: no root guard configured - Current root guard off

% port1.0.2: Configured Link Type point-to-point - Current shared

%

% Instance 2: Vlans: 2

% 1: MSTI Root Path Cost 0 -MSTI Root Port 0 - MSTI Bridge Priority 32768

% 1: MSTI Root Id 80020000cd24ff2d

% 1: MSTI Bridge Id 80020000cd24ff2d

% port1.0.2: Port 5002 - Id 838a - Role Disabled - State Discarding

% port1.0.2: Designated Internal Path Cost 0 - Designated Port Id 838a

% port1.0.2: Configured Internal Path Cost 20000000

% port1.0.2: Configured CST External Path cost 20000000

% port1.0.2: CST Priority 128 - MSTI Priority 128

% port1.0.2: Designated Root 80020000cd24ff2d

% port1.0.2: Designated Bridge 80020000cd24ff2d

% port1.0.2: Message Age 0 - Max Age 0

% port1.0.2: Hello Time 2 - Forward Delay 15

% port1.0.2: Forward Timer 0 - Msg Age Timer 0 - Hello Timer 0

613-50137-01 Rev A Command Reference for FS980M Series 468

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE MST INSTANCE

show spanning-tree mst instance

Overview This command displays detailed information for the specified instance, and all

switch ports associated with that instance.

A topology change counter has been included for RSTP and MSTP. You can see the

topology change counter for RSTP by using the show spanning-tree command.

You can see the topology change counter for MSTP by using the show

spanning-tree mst instance command.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show spanning-tree mst instance <instance-id>

Mode User Exec, Privileged Exec, and Interface Configuration

Example To display detailed information for instance 2, and all switch ports associated with

that instance, use the command:

awplus# show spanning-tree mst instance 2

Output Figure 14-9: Example output from show spanning-tree mst instance

Parameter Description

<instance-id>Specify an MSTP instance in the range 1-5.

% 1: MSTI Root Path Cost 0 - MSTI Root Port 0 - MSTI Bridge Priority 32768

% 1: MSTI Root Id 80020000cd24ff2d

% 1: MSTI Bridge Id 80020000cd24ff2d

% port1.0.2: Port 5002 - Id 838a - Role Disabled - State Discarding

% port1.0.2: Designated Internal Path Cost 0 - Designated Port Id 838a

% port1.0.2: Configured Internal Path Cost 20000000

% port1.0.2: Configured CST External Path cost 20000000

% port1.0.2: CST Priority 128 - MSTI Priority 128

% port1.0.2: Designated Root 80020000cd24ff2d

% port1.0.2: Designated Bridge 80020000cd24ff2d

% port1.0.2: Message Age 0 - Max Age 0

% port1.0.2: Hello Time 2 - Forward Delay 15

% port1.0.2: Forward Timer 0 - Msg Age Timer 0 - Hello Timer 0

613-50137-01 Rev A Command Reference for FS980M Series 469

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE MST INSTANCE INTERFACE

show spanning-tree mst instance interface

Overview This command displays detailed information for the specified MST (Multiple

Spanning Tree) instance, and the specified switch port associated with that MST

instance.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show spanning-tree mst instance <instance-id> interface <port>

Mode User Exec, Privileged Exec, and Interface Configuration

Example To display detailed information for instance 2, interface port1.0.2, use the

command:

awplus# show spanning-tree mst instance 2 interface port1.0.2

Output Figure 14-10: Example output from show spanning-tree mst instance

Parameter Description

<instance-id>Specify an MSTP instance in the range 1-5.

<port>The port to display information about. The port may be a switch

port (e.g. port1.0.4), a static channel group (e.g. sa2), or a dynamic

(LACP) channel group (e.g. po2).

% 1: MSTI Root Path Cost 0 - MSTI Root Port 0 - MSTI Bridge Priority 32768

% 1: MSTI Root Id 80020000cd24ff2d

% 1: MSTI Bridge Id 80020000cd24ff2d

% port1.0.2: Port 5002 - Id 838a - Role Disabled - State Discarding

% port1.0.2: Designated Internal Path Cost 0 - Designated Port Id 838a

% port1.0.2: Configured Internal Path Cost 20000000

% port1.0.2: Configured CST External Path cost 20000000

% port1.0.2: CST Priority 128 - MSTI Priority 128

% port1.0.2: Designated Root 80020000cd24ff2d

% port1.0.2: Designated Bridge 80020000cd24ff2d

% port1.0.2: Message Age 0 - Max Age 0

% port1.0.2: Hello Time 2 - Forward Delay 15

% port1.0.2: Forward Timer 0 - Msg Age Timer 0 - Hello Timer 0

613-50137-01 Rev A Command Reference for FS980M Series 470

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE MST INTERFACE

show spanning-tree mst interface

Overview This command displays the number of instances created, and VLANs associated

with it for the specified switch port.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show spanning-tree mst interface <port>

Mode User Exec, Privileged Exec, and Interface Configuration

Example To display detailed information about each instance, and all interfaces associated

with them, for port1.0.4, use the command:

awplus# show spanning-tree mst interface port1.0.4

Output Figure 14-11: Example output from show spanning-tree mst interface

Parameter Description

<port>The port to display information about. The port may be a switch port

(e.g. port1.0.4), a static channel group (e.g. sa2), or a dynamic

(LACP) channel group (e.g. po2).

% 1: Bridge up - Spanning Tree Enabled

% 1: CIST Root Path Cost 0 - CIST Root Port 0 - CIST Bridge Priority 32768

% 1: Forward Delay 15 - Hello Time 2 - Max Age 20 - Max-hops 20

% 1: CIST Root Id 80000008c73a2b22

% 1: CIST Reg Root Id 80000008c73a2b22

% 1: CST Bridge Id 80000008c73a2b22

% 1: portfast bpdu-filter disabled

% 1: portfast bpdu-guard disabled

% 1: portfast errdisable timeout disabled

% 1: portfast errdisable timeout interval 1 sec

%

% Instance VLAN

% 0: 1

% 1: 2-3

% 2: 4-5

613-50137-01 Rev A Command Reference for FS980M Series 471

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE MST DETAIL INTERFACE

show spanning-tree mst detail interface

Overview This command displays detailed information about the specified switch port, and

the MST instances associated with it.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show spanning-tree mst detail interface <port>

Mode User Exec, Privileged Exec and Interface Configuration

Example To display detailed information about port1.0.3 and the instances associated

with it, enter the command:

awplus# show spanning-tree mst detail interface port1.0.3

Output Figure 14-12: Example output from show spanning-tree mst detail interface

Parameter Description

<port>The port to display information about. The port may be a switch port

(e.g. port1.0.4), a static channel group (e.g. sa2), or a dynamic

(LACP) channel group (e.g. po2).

% 1: Bridge up - Spanning Tree Enabled

% 1: CIST Root Path Cost 0 - CIST Root Port 0 - CIST Bridge Priority 32768

% 1: Forward Delay 15 - Hello Time 2 - Max Age 20 - Max-hops 20

% 1: CIST Root Id 80000000cd24ff2d

% 1: CIST Reg Root Id 80000000cd24ff2d

% 1: CIST Bridge Id 80000000cd24ff2d

% 1: portfast bpdu-filter disabled

% 1: portfast bpdu-guard disabled

% 1: portfast errdisable timeout disabled

% 1: portfast errdisable timeout interval 300 sec

% port1.0.2: Port 5002 - Id 838a - Role Disabled - State Discarding

% port1.0.2: Designated External Path Cost 0 -Internal Path Cost 0

% port1.0.2: Configured Path Cost 20000000 - Add type Explicit ref count 2

% port1.0.2: Designated Port Id 838a - CIST Priority 128 -

% port1.0.2: CIST Root 80000000cd24ff2d

% port1.0.2: Regional Root 80000000cd24ff2d

% port1.0.2: Designated Bridge 80000000cd24ff2d

% port1.0.2: Message Age 0 - Max Age 20

% port1.0.2: CIST Hello Time 2 - Forward Delay 15

% port1.0.2: CIST Forward Timer 0 - Msg Age Timer 0 - Hello Timer 0 - topo 

change timer 0

% port1.0.2: forward-transitions 0

% port1.0.2: Version Multiple Spanning Tree Protocol - Received None - Send STP

613-50137-01 Rev A Command Reference for FS980M Series 472

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE MST DETAIL INTERFACE

% port1.0.2: No portfast configured - Current portfast off

% port1.0.2: portfast bpdu-guard default - Current portfast bpdu-guard off

% port1.0.2: portfast bpdu-filter default - Current portfast bpdu-filter off

% port1.0.2: no root guard configured - Current root guard off

% port1.0.2: Configured Link Type point-to-point - Current shared

%

% Instance 2: Vlans: 2

% 1: MSTI Root Path Cost 0 -MSTI Root Port 0 - MSTI Bridge Priority 32768

% 1: MSTI Root Id 80020000cd24ff2d

% 1: MSTI Bridge Id 80020000cd24ff2d

% port1.0.2: Port 5002 - Id 838a - Role Disabled - State Discarding

% port1.0.2: Designated Internal Path Cost 0 - Designated Port Id 838a

% port1.0.2: Configured Internal Path Cost 20000000

% port1.0.2: Configured CST External Path cost 20000000

% port1.0.2: CST Priority 128 - MSTI Priority 128

% port1.0.2: Designated Root 80020000cd24ff2d

% port1.0.2: Designated Bridge 80020000cd24ff2d

% port1.0.2: Message Age 0 - Max Age 0

% port1.0.2: Hello Time 2 - Forward Delay 15

% port1.0.2: Forward Timer 0 - Msg Age Timer 0 - Hello Timer 0

613-50137-01 Rev A Command Reference for FS980M Series 473

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE STATISTICS

show spanning-tree statistics

Overview This command displays BPDU (Bridge Protocol Data Unit) statistics for all

spanning-tree instances, and all switch ports associated with all spanning-tree

instances.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show spanning-tree statistics

Mode Privileged Exec

Usage To display BPDU statistics for all spanning-tree instances, and all switch ports

associated with all spanning-tree instances, use the command:

awplus# show spanning-tree statistics

Output Figure 14-13: Example output from show spanning-tree statistics

Port number = 915 Interface = port1.0.6

================================

% BPDU Related Parameters

% -----------------------

% Port Spanning Tree : Disable

% Spanning Tree Type : Rapid Spanning Tree Protocol

% Current Port State : Discarding

% Port ID : 8393

% Port Number : 393

% Path Cost : 20000000

% Message Age : 0

% Designated Root : ec:cd:6d:20:c0:ed

% Designated Cost : 0

% Designated Bridge : ec:cd:6d:20:c0:ed

% Designated Port Id : 8393

% Top Change Ack : FALSE

% Config Pending : FALSE

% PORT Based Information & Statistics

% -----------------------------------

% Config Bpdu's xmitted : 0

% Config Bpdu's received : 0

% TCN Bpdu's xmitted : 0

% TCN Bpdu's received : 0

% Forward Trans Count : 0

613-50137-01 Rev A Command Reference for FS980M Series 474

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE STATISTICS

% STATUS of Port Timers

% ---------------------

% Hello Time Configured : 2

% Hello timer : INACTIVE

% Hello Time Value : 0

% Forward Delay Timer : INACTIVE

% Forward Delay Timer Value : 0

% Message Age Timer : INACTIVE

% Message Age Timer Value : 0

% Topology Change Timer : INACTIVE

% Topology Change Timer Value : 0

% Hold Timer : INACTIVE

% Hold Timer Value : 0

% Other Port-Specific Info

------------------------

% Max Age Transitions : 1

% Msg Age Expiry : 0

% Similar BPDUS Rcvd : 0

% Src Mac Count : 0

% Total Src Mac Rcvd : 0

% Next State : Learning

% Topology Change Time : 0

613-50137-01 Rev A Command Reference for FS980M Series 475

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE STATISTICS INSTANCE

show spanning-tree statistics instance

Overview This command displays BPDU (Bridge Protocol Data Unit) statistics for the specified

MST (Multiple Spanning Tree) instance, and all switch ports associated with that

MST instance.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show spanning-tree statistics instance <instance-id>

Mode Privileged Exec

Example To display BPDU statistics information for MST instance 2, and all switch ports

associated with that MST instance, use the command:

awplus# show spanning-tree statistics instance 2

Output Figure 14-14: Example output from show spanning-tree statistics instance

Commands

show spanning-tree statistics

Parameter Description

<instance-id>Specify an MSTP instance in the range 1-5.

% % INST_PORT port1.0.3 Information & Statistics

% ----------------------------------------

% Config Bpdu's xmitted (port/inst) : (0/0)

% Config Bpdu's received (port/inst) : (0/0)

% TCN Bpdu's xmitted (port/inst) : (0/0)

% TCN Bpdu's received (port/inst) : (0/0)

% Message Age(port/Inst) : (0/0)

% port1.0.3: Forward Transitions : 0

% Next State : Learning

% Topology Change Time : 0

...

613-50137-01 Rev A Command Reference for FS980M Series 476

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE STATISTICS INSTANCE INTERFACE

show spanning-tree statistics instance

interface

Overview This command displays BPDU (Bridge Protocol Data Unit) statistics for the specified

MST (Multiple Spanning Tree) instance and the specified switch port associated

with that MST instance.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show spanning-tree statistics instance <instance-id> interface

<port>

Mode Privileged Exec

Example To display BPDU statistics for MST instance 2, interface port1.0.2, use the

command:

awplus# show spanning-tree statistics instance 2 interface

port1.0.2

Parameter Description

<instance-id>Specify an MSTP instance in the range 1-5.

<port>The port to display information about. The port may be a switch

port (e.g. port1.0.4), a static channel group (e.g. sa2), or a

dynamic (LACP) channel group (e.g. po2).

613-50137-01 Rev A Command Reference for FS980M Series 477

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE STATISTICS INSTANCE INTERFACE

Output Figure 14-15: Example output from show spanning-tree statistics instance

interface

Commands

show spanning-tree statistics

awplus#sh spanning-tree statistics interface port1.0.2 instance 1

Spanning Tree Enabled for Instance : 1

==================================

% INST_PORT port1.0.2 Information & Statistics

% ----------------------------------------

% Config Bpdu's xmitted (port/inst) : (0/0)

% Config Bpdu's received (port/inst) : (0/0)

% TCN Bpdu's xmitted (port/inst) : (0/0)

% TCN Bpdu's received (port/inst) : (0/0)

% Message Age(port/Inst) : (0/0)

% port1.0.2: Forward Transitions : 0

% Next State : Learning

% Topology Change Time : 0



% Other Inst/Vlan Information & Statistics

% ----------------------------------------

% Bridge Priority : 0

% Bridge Mac Address : ec:cd:6d:20:c0:ed

% Topology Change Initiator : 5023

% Last Topology Change Occured : Mon Oct 3 05:42:06 2016

% Topology Change : FALSE

% Topology Change Detected : FALSE

% Topology Change Count : 1

% Topology Change Last Recvd from : 00:00:00:00:00:00

613-50137-01 Rev A Command Reference for FS980M Series 478

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE STATISTICS INTERFACE

show spanning-tree statistics interface

Overview This command displays BPDU (Bridge Protocol Data Unit) statistics for the specified

switch port, and all MST instances associated with that switch port.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show spanning-tree statistics interface <port>

Mode Privileged Exec

Example To display BPDU statistics about each MST instance for port1.0.4, use the

command:

awplus# show spanning-tree statistics interface port1.0.4

Output Figure 14-16: Example output from show spanning-tree statistics interface

Parameter Description

<port>The port to display information about. The port may be a switch port

(e.g. port1.0.4), a static channel group (e.g. sa2), or a dynamic (LACP)

channel group (e.g. po2).



awplus#show spanning-tree statistics interface port1.0.2



Port number = 906 Interface = port1.0.2

================================

% BPDU Related Parameters

% -----------------------

% Port Spanning Tree : Disable

% Spanning Tree Type : Multiple Spanning Tree Protocol

% Current Port State : Discarding

% Port ID : 838a

% Port Number : 38a

% Path Cost : 20000000

% Message Age : 0

% Designated Root : ec:cd:6d:20:c0:ed

% Designated Cost : 0

% Designated Bridge : ec:cd:6d:20:c0:ed

% Designated Port Id : 838a

% Top Change Ack : FALSE

% Config Pending : FALSE

613-50137-01 Rev A Command Reference for FS980M Series 479

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE STATISTICS INTERFACE

Commands

show spanning-tree statistics

% PORT Based Information & Statistics

% -----------------------------------

% Config Bpdu's xmitted : 0

% Config Bpdu's received : 0

% TCN Bpdu's xmitted : 0

% TCN Bpdu's received : 0

% Forward Trans Count : 0

% STATUS of Port Timers

% ---------------------

% Hello Time Configured : 2

% Hello timer : INACTIVE

% Hello Time Value : 0

% Forward Delay Timer : INACTIVE

% Forward Delay Timer Value : 0

% Message Age Timer : INACTIVE

% Message Age Timer Value : 0

% Topology Change Timer : INACTIVE

% Topology Change Timer Value : 0

% Hold Timer : INACTIVE

% Hold Timer Value : 0

% Other Port-Specific Info

------------------------

% Max Age Transitions : 1

% Msg Age Expiry : 0

% Similar BPDUS Rcvd : 0

% Src Mac Count : 0

% Total Src Mac Rcvd : 0

% Next State : Learning

% Topology Change Time : 0

% Other Bridge information & Statistics

--------------------------------------

% STP Multicast Address : 01:80:c2:00:00:00

% Bridge Priority : 32768

% Bridge Mac Address : ec:cd:6d:20:c0:ed

% Bridge Hello Time : 2

% Bridge Forward Delay : 15

% Topology Change Initiator : 5023

% Last Topology Change Occured : Mon Oct 3 05:41:20 2016

% Topology Change : FALSE

% Topology Change Detected : TRUE

% Topology Change Count : 1

% Topology Change Last Recvd from : 00:00:00:00:00:00

613-50137-01 Rev A Command Reference for FS980M Series 480

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SHOW SPANNING-TREE VLAN RANGE-INDEX

show spanning-tree vlan range-index

Overview Use this command to display information about MST (Multiple Spanning Tree)

instances and the VLANs associated with them including the VLAN range-index

value for the device.

Syntax show spanning-tree vlan range-index

Mode Privileged Exec

Example To display information about MST instances and the VLANs associated with them

for the device, including the VLAN range-index value, use the following command:

awplus# show spanning-tree vlan range-index

Output Figure 14-17: Example output from show spanning-tree vlan range-index

Commands

show spanning-tree statistics

awplus#show spanning-tree vlan range-index

% MST Instance VLAN RangeIdx

% 1 1 1%

613-50137-01 Rev A Command Reference for FS980M Series 481

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE AUTOEDGE (RSTP AND MSTP)

spanning-tree autoedge (RSTP and MSTP)

Overview Use this command to enable the autoedge feature on the port.

The autoedge feature allows the port to automatically detect that it is an edge

port. If it does not receive any BPDUs in the first three seconds after linkup,

enabling, or entering RSTP or MSTP mode, it sets itself to be an edgeport and

enters the forwarding state.

Use this command for RSTP or MSTP.

Use the no variant of this command to disable this feature.

Syntax spanning-tree autoedge

no spanning-tree autoedge

Default Disabled

Mode Interface Configuration

Example awplus# configure terminal

awplus(config)# interface port1.0.3

awplus(config-if)# spanning-tree autoedge

Commands

spanning-tree edgeport (RSTP and MSTP)

613-50137-01 Rev A Command Reference for FS980M Series 482

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE BPDU

spanning-tree bpdu

Overview Use this command in Global Configuration mode to configure BPDU (Bridge

Protocol Data Unit) discarding or forwarding, with STP (Spanning Tree Protocol)

disabled on the switch.

See the Usage note about disabling Spanning Tree before using this command,

and using this command to forward unsupported BPDUs unchanged for

unsupported STP Protocols.

There is not a no variant for this command. Instead, apply the discard parameter

to reset it back to the default then re-enable STP with spanning-tree enable

command.

Syntax spanning-tree bpdu

{discard|forward|forward-untagged-vlan|forward-vlan}

Default The discard parameter is enabled by default.

Mode Global Configuration

Usage You must first disable Spanning Tree with the spanning-tree enable command

before you can use this command to then configure BPDU discarding or

forwarding.

This command enables the switch to forward unsupported BPDUs with an

unsupported Spanning Tree Protocol, such as proprietary STP protocols with

unsupported BPDUs, by forwarding BDPU (Bridge Protocol Data Unit) frames

unchanged through the switch.

When you want to revert to default behavior on the switch, issue a spanning-tree

bdpu discard command and re-enable Spanning Tree with a s panning-tree

enable command.

Parameter Description

bpdu A port that has BPDU filtering enabled will not transmit any BPDUs

and will ignore any BPDUs received. This port type has one of the

following parameters (in Global Configuration mode):

discard Discards all ingress STP BPDU frames.

forward Forwards any ingress STP BPDU packets to all ports,

regardless of any VLAN membership.

forward-

untagged-

vlan

Forwards any ingress STP BPDU frames to all ports

that are untagged members of the ingress port’s

native VLAN.

forward-

vlan

Forwards any ingress STP BPDU frames to all ports

that are tagged members of the ingress port’s native

VLAN.

613-50137-01 Rev A Command Reference for FS980M Series 483

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE BPDU

Examples To enable STP BPDU discard in Global Configuration mode with STP disabled,

which discards all ingress STP BPDU frames, enter the commands:

awplus# configure terminal

awplus(config)# no spanning-tree stp enable

awplus(config)# spanning-tree bpdu discard

To enable STP BPDU forward in Global Configuration mode with STP disabled,

which forwards any ingress STP BPDU frames to all ports regardless of any VLAN

membership, enter the commands:

awplus# configure terminal

awplus(config)# no spanning-tree stp enable

awplus(config)# spanning-tree bpdu forward

To enable STP BPDU forwarding for untagged frames in Global Configuration

mode with STP disabled, which forwards any ingress STP BPDU frames to all ports

that are untagged members of the ingress port’s native VLAN, enter the

commands:

awplus# configure terminal

awplus(config)# no spanning-tree stp enable

awplus(config)# spanning-tree bpdu forward-untagged-vlan

To enable STP BPDU forwarding for tagged frames in Global Configuration mode

with STP disabled, which forwards any ingress STP BPDU frames to all ports that are

tagged members of the ingress port’s native VLAN, enter the commands:

awplus# configure terminal

awplus(config)# no spanning-tree stp enable

awplus(config)# spanning-tree bpdu forward-vlan

To reset STP BPDU back to the default discard parameter and re-enable STP on

the switch, enter the commands:

awplus# configure terminal

awplus(config)# spanning-tree bpdu discard

awplus(config)# spanning-tree stp enable

Commands

show spanning-tree

spanning-tree enable

613-50137-01 Rev A Command Reference for FS980M Series 484

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE CISCO-INTEROPERABILITY (MSTP)

spanning-tree cisco-interoperability (MSTP)

Overview Use this command to enable/disable Cisco-interoperability for MSTP.

Use this command for MSTP only.

Syntax spanning-tree cisco-interoperability {enable|disable}

Default If this command is not used, Cisco interoperability is disabled.

Mode Global Configuration

Usage For compatibility with certain Cisco devices, all devices in the switched LAN

running the AlliedWare Plus™ Operating System must have Cisco-interoperability

enabled. When the AlliedWare Plus Operating System is interoperating with Cisco,

the only criteria used to classify a region are the region name and revision level.

VLAN to instance mapping is not used to classify regions when interoperating with

Cisco.

Examples To enable Cisco interoperability on a Layer 2 device:

awplus# configure terminal

awplus(config)# spanning-tree cisco-interoperability enable

To disable Cisco interoperability on a Layer 2 device:

awplus# configure terminal

awplus(config)# spanning-tree cisco-interoperability disable

Parameter Description

enable Enable Cisco interoperability for MSTP.

disable Disable Cisco interoperability for MSTP.

613-50137-01 Rev A Command Reference for FS980M Series 485

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE EDGEPORT (RSTP AND MSTP)

spanning-tree edgeport (RSTP and MSTP)

Overview Use this command to set a port as an edge-port.

Use this command for RSTP or MSTP.

This command has the same effect as the spanning-tree portfast (STP) command,

but the configuration displays differently in the output of some show commands.

Use the no variant of this command to set a port to its default state (not an

edge-port).

Syntax spanning-tree edgeport

no spanning-tree edgeport

Default Not an edge port.

Mode Interface Configuration

Usage Use this command on a switch port connected to a LAN that has no other bridges

attached. If a BPDU is received on the port that indicates that another bridge is

connected to the LAN, then the port is no longer treated as an edge port.

Example awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# spanning-tree edgeport

Commands

spanning-tree autoedge (RSTP and MSTP)

613-50137-01 Rev A Command Reference for FS980M Series 486

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE ENABLE

spanning-tree enable

Overview Use this command in Global Configuration mode to enable the specified spanning

tree protocol for all switch ports. Note that this must be the spanning tree protocol

that is configured on the device by the spanning-tree mode command.

Use the no variant of this command to disable the configured spanning tree

protocol. This places all switch ports in the forwarding state.

Syntax spanning-tree {mstp|rstp|stp} enable

no spanning-tree {mstp|rstp|stp} enable

Default RSTP is enabled by default for all switch ports.

Mode Global Configuration

Usage With no configuration, spanning tree is enabled, and the spanning tree mode is set

to RSTP. To change the mode, see spanning-tree mode command.

Examples To enable STP in Global Configuration mode, enter the below commands:

awplus# configure terminal

awplus(config)# spanning-tree stp enable

To disable STP in Global Configuration mode, enter the below commands:

awplus# configure terminal

awplus(config)# no spanning-tree stp enable

To enable MSTP in Global Configuration mode, enter the below commands:

awplus# configure terminal

awplus(config)# spanning-tree mstp enable

To disable MSTP in Global Configuration mode, enter the below commands:

awplus# configure terminal

awplus(config)# no spanning-tree mstp enable

To enable RSTP in Global Configuration mode, enter the below commands:

awplus# configure terminal

awplus(config)# spanning-tree rstp enable

Parameter Description

mstp Enables or disables MSTP (Multiple Spanning Tree Protocol).

rstp Enables or disables RSTP (Rapid Spanning Tree Protocol).

stp Enables or disables STP (Spanning Tree Protocol).

613-50137-01 Rev A Command Reference for FS980M Series 487

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE ENABLE

To disable RSTP in Global Configuration mode, enter the below commands:

awplus# configure terminal

awplus(config)# no spanning-tree rstp enable

Commands

spanning-tree bpdu

spanning-tree mode

613-50137-01 Rev A Command Reference for FS980M Series 488

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE ERRDISABLE-TIMEOUT ENABLE

spanning-tree errdisable-timeout enable

Overview Use this command to enable the errdisable-timeout facility, which sets a timeout

for ports that are disabled due to the BPDU guard feature.

Use this command for RSTP or MSTP.

Use the no variant of this command to disable the errdisable-timeout facility.

Syntax spanning-tree errdisable-timeout enable

no spanning-tree errdisable-timeout enable

Default By default, the errdisable-timeout is disabled.

Mode Global Configuration

Usage The BPDU guard feature shuts down the port on receiving a BPDU on a

BPDU-guard enabled port. This command associates a timer with the feature such

that the port is re- enabled without manual intervention after a set interval. This

interval can be configured by the user using the spanning-tree errdisable-timeout

interval command.

Example awplus# configure terminal

awplus(config)# spanning-tree errdisable-timeout enable

Commands

show spanning-tree

spanning-tree errdisable-timeout interval

spanning-tree portfast bpdu-guard

613-50137-01 Rev A Command Reference for FS980M Series 489

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE ERRDISABLE-TIMEOUT INTERVAL

spanning-tree errdisable-timeout interval

Overview Use this command to specify the time interval after which a port is brought back

up when it has been disabled by the BPDU guard feature.

Use this command for RSTP or MSTP.

Syntax spanning-tree errdisable-timeout interval <10-1000000>

no spanning-tree errdisable-timeout interval

Default By default, the port is re-enabled after 300 seconds.

Mode Global Configuration

Example awplus# configure terminal

awplus(config)# spanning-tree errdisable-timeout interval 34

Commands

show spanning-tree

spanning-tree errdisable-timeout enable

spanning-tree portfast bpdu-guard

Parameter Description

<10-1000000> Specify the errdisable-timeout interval in seconds.

613-50137-01 Rev A Command Reference for FS980M Series 490

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE FORCE-VERSION

spanning-tree force-version

Overview Use this command in Interface Configuration mode for a switch port interface only

to force the protocol version for the switch port. Use this command for RSTP or

MSTP only.

Syntax spanning-tree force-version <version>

no spanning-tree force-version

Default By default, no version is forced for the port. The port is in the spanning tree mode

configured for the device, or a lower version if it automatically detects one.

Mode Interface Configuration mode for a switch port interface only.

Examples Set the value to enforce the spanning tree protocol (STP):

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# spanning-tree force-version 0

Set the default protocol version:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no spanning-tree force-version

Commands

show spanning-tree

Parameter Description

<version> <0-3> Version identifier.

0Forces the port to operate in STP mode.

1Not supported.

2Forces the port to operate in RSTP mode. If it receives STP

BPDUs, it can automatically revert to STP mode.

3Forces the port to operate in MSTP mode (this option is only

available if MSTP mode is configured). If it receives RSTP or

STP BPDUs, it can automatically revert to RSTP or STP mode.

613-50137-01 Rev A Command Reference for FS980M Series 491

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE FORWARD-TIME

spanning-tree forward-time

Overview Use this command to set the forward delay value. Use the no variant of this

command to reset the forward delay value to the default setting of 15 seconds.

The forward delay sets the time (in seconds) to control how fast a port changes its

spanning tree state when moving towards the forwarding state. If the mode is set

to STP, the value determines how long the port stays in each of the listening and

learning states which precede the forwarding state. If the mode is set to RSTP or

MSTP, this value determines the maximum time taken to transition from

discarding to learning and from learning to forwarding.

This value is used only when the device is acting as the root bridge. Devices not

acting as the Root Bridge use a dynamic value for the forward delay set by the root

bridge. The forward delay, max-age, and hello time parameters are interrelated.

Syntax spanning-tree forward-time <forward-delay>

no spanning-tree forward-time

Default The default is 15 seconds.

Mode Global Configuration

Usage The allowable range for forward-time is 4-30 seconds.

The forward delay, max-age, and hello time parameters should be set according

to the following formula, as specified in IEEE Standard 802.1d:

2 x (forward delay - 1.0 seconds) >= max-age

max-age >= 2 x (hello time + 1.0 seconds)

Example awplus# configure terminal

awplus(config)# spanning-tree forward-time 6

Commands

show spanning-tree

spanning-tree forward-time

spanning-tree hello-time

spanning-tree mode

Parameter Description

<forward-delay> <4-30> The forwarding time delay in seconds.

613-50137-01 Rev A Command Reference for FS980M Series 492

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE GUARD ROOT

spanning-tree guard root

Overview Use this command in Interface Configuration mode for a switch port only to enable

the Root Guard feature for the switch port. The root guard feature disables

reception of superior BPDUs. You can use this command for RSTP, STP or MSTP.

Use the no variant of this command to disable the root guard feature for the port.

Syntax spanning-tree guard root

no spanning-tree guard root

Mode Interface Configuration mode for a switch port interface only.

Usage The Root Guard feature makes sure that the port on which it is enabled is a

designated port. If the Root Guard enabled port receives a superior BPDU, it goes

to a Listening state (for STP) or discarding state (for RSTP and MSTP).

Example awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# spanning-tree guard root

613-50137-01 Rev A Command Reference for FS980M Series 493

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE HELLO-TIME

spanning-tree hello-time

Overview Use this command to set the hello-time. This sets the time in seconds between the

transmission of device spanning tree configuration information when the device is

the Root Bridge of the spanning tree or is trying to become the Root Bridge.

Use this command for RSTP, STP or MSTP.

Use the no variant of this command to restore the default of the hello time.

Syntax spanning-tree hello-time <hello-time>

no spanning-tree hello-time

Default Default is 2 seconds.

Mode Global Configuration and Interface Configuration for switch ports.

Usage The allowable range of values is 1-10 seconds.

The forward delay, max-age, and hello time parameters should be set according to

the following formula, as specified in IEEE Standard 802.1d:

2 x (forward delay - 1.0 seconds) >= max-age

max-age>= 2 x (hello time + 1.0 seconds)

Example awplus# configure terminal

awplus(config)# spanning-tree hello-time 3

Commands

spanning-tree forward-time

spanning-tree max-age

show spanning-tree

Parameter Description

<hello-time><1-10> The hello BPDU interval in seconds.

613-50137-01 Rev A Command Reference for FS980M Series 494

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE LINK-TYPE

spanning-tree link-type

Overview Use this command in Interface Configuration mode for a switch port interface only

to enable or disable point-to-point or shared link types on the switch port.

Use this command for RSTP or MSTP only.

Use the no variant of this command to return the port to the default link type.

Syntax spanning-tree link-type {point-to-point|shared}

no spanning-tree link-type

Default The default link type is point-to-point.

Mode Interface Configuration mode for a switch port interface only.

Usage You may want to set link type to shared if the port is connected to a hub with

multiple devices connected to it.

Examples awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# spanning-tree link-type point-to-point

Parameter Description

shared Disable rapid transition.

point-to-point Enable rapid transition.

613-50137-01 Rev A Command Reference for FS980M Series 495

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE MAX-AGE

spanning-tree max-age

Overview Use this command to set the max-age. This sets the maximum age, in seconds, that

dynamic spanning tree configuration information is stored in the device before it

is discarded.

Use this command for RSTP, STP or MSTP.

Use the no variant of this command to restore the default of max-age.

Syntax spanning-tree max-age <max-age>

no spanning-tree max-age

Default The default of spanning-tree max-age is 20 seconds.

Mode Global Configuration

Usage Max-age is the maximum time in seconds for which a message is considered valid.

Configure this value sufficiently high, so that a frame generated by the root bridge

can be propagated to the leaf nodes without exceeding the max-age.

The forward delay, max-age, and hello time parameters should be set according

to the following formula, as specified in IEEE Standard 802.1d:

2 x (forward delay - 1.0 seconds) >= max-age

max-age >= 2 x (hello time + 1.0 seconds)

Example awplus# configure terminal

awplus(config)# spanning-tree max-age 12

Commands

show spanning-tree

spanning-tree forward-time

spanning-tree hello-time

Parameter Description

<max-age><6-40> The maximum time, in seconds.

613-50137-01 Rev A Command Reference for FS980M Series 496

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE MAX-HOPS (MSTP)

spanning-tree max-hops (MSTP)

Overview Use this command to specify the maximum allowed hops for a BPDU in an MST

region. This parameter is used by all the instances of the MST region.

Use the no variant of this command to restore the default.

Use this command for MSTP only.

Syntax spanning-tree max-hops <hop-count>

no spanning-tree max-hops <hop-count>

Default The default max-hops in a MST region is 20.

Mode Global Configuration

Usage Specifying the max hops for a BPDU prevents the messages from looping

indefinitely in the network. The hop count is decremented by each receiving port.

When a device receives an MST BPDU that has a hop count of zero, it discards the

BPDU.

Examples awplus# configure terminal

awplus(config)# spanning-tree max-hops 25

awplus# configure terminal

awplus(config)# no spanning-tree max-hops

Parameter Description

<hop-count> Specify the maximum hops the BPDU will be valid for in the range

<1-40>.

613-50137-01 Rev A Command Reference for FS980M Series 497

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE MODE

spanning-tree mode

Overview Use this command to change the spanning tree protocol mode on the device. The

spanning tree protocol mode on the device can be configured to either STP, RSTP

or MSTP.

Syntax spanning-tree mode {stp|rstp|mstp}

Default The default spanning tree protocol mode on the device is RSTP.

Mode Global Configuration

Usage With no configuration, the device will have spanning tree enabled, and the

spanning tree mode will be set to RSTP. Use this command to change the spanning

tree protocol mode on the device. MSTP is VLAN aware, but RSTP and STP are not

VLAN aware. To enable or disable spanning tree operation, see the spanning-tree

enable command.

Examples To change the spanning tree mode from the default of RSTP to MSTP, use the

following commands:

awplus# configure terminal

awplus(config)# spanning-tree mode mstp

Commands

spanning-tree enable

613-50137-01 Rev A Command Reference for FS980M Series 498

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE MST CONFIGURATION

spanning-tree mst configuration

Overview Use this command to enter the MST Configuration mode to configure the Multiple

Spanning-Tree Protocol.

Syntax spanning-tree mst configuration

Mode Global Configuration

Examples The following example uses this command to enter MST Configuration mode. Note

the change in the command prompt.

awplus# configure terminal

awplus(config)# spanning-tree mst configuration

awplus(config-mst)#

613-50137-01 Rev A Command Reference for FS980M Series 499

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE MST INSTANCE

spanning-tree mst instance

Overview Use this command to assign a Multiple Spanning Tree instance (MSTI) to a switch

port or channel group.

Note that ports are automatically configured to send and receive spanning-tree

information for the associated MSTI when VLANs are assigned to MSTIs using the

instance vlan (MSTP) command.

Use the no variant of this command in Interface Configuration mode to remove the

MSTI from the specified switch port or channel group.

Syntax spanning-tree mst instance <instance-id>

no spanning-tree mst instance <instance-id>

Default A port automatically becomes a member of an MSTI when it is assigned to a VLAN.

Mode Interface Configuration mode for a switch port or channel group.

Usage You can disable automatic configuration of member ports of a VLAN to an

associated MSTI by using a no spanning-tree mst instance command to remove

the member port from the MSTI. Use the spanning-tree mst instance command

to add a VLAN member port back to the MSTI.

Examples To assign instance 3 to a switch port, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# spanning-tree mst instance 3

To remove instance 3 from a switch port, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no spanning-tree mst instance 3

Commands

instance vlan (MSTP)

spanning-tree mst instance path-cost

spanning-tree mst instance priority

spanning-tree mst instance restricted-role

spanning-tree mst instance restricted-tcn

Parameter Description

<instance-id>Specify an MSTP instance in the range 1-5. The MST instance must

have already been created using the instance vlan (MSTP)

command.

613-50137-01 Rev A Command Reference for FS980M Series 500

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE MST INSTANCE PATH-COST

spanning-tree mst instance path-cost

Overview Use this command to set the cost of a path associated with a switch port, for the

specified MSTI.

This specifies the switch port’s contribution to the cost of a path to the MSTI

regional root via that port. This applies when the port is the root port for the MSTI.

Use the no variant of this command to restore the default cost value of the path.

Syntax spanning-tree mst instance <instance-id> path-cost <path-cost>

no spanning-tree mst instance <instance-id> path-cost

Default The default path cost values and the range of recommended path cost values

depend on the port speed, as shown in the following table from the IEEE

802.1q-2003 standard.

Mode Interface Configuration mode for a switch port interface only.

Usage Before you can use this command to set a path-cost in a VLAN configuration, you

must explicitly add an MST instance to a port using the spanning-tree mst instance

command.

Examples To set a path cost of 1000 on instance 3, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# spanning-tree mst instance 3 path-cost 1000

Parameter Description

<instance-id>Specify an MSTP instance in the range 1-5.

<path-cost> Specify the cost of path in the range of <1-200000000>, where

a lower path-cost indicates a greater likelihood of the specific

interface becoming a root.

Port speed Default path cost Recommended path cost range

Less than 100 Kb/s

1Mbps

10Mbps

100 Mbps

1 Gbps

10 Gbps

100 Gbps

1Tbps

10 Tbps

200,000,000

20,000,000

2,000,000

200,000

20,000

2,000

200

20,000,000-200,000,000

2,000,000-20,000,000

200,000-2,000,000

20,000-200,000

2,000-20,000

200-2, 000

20-200

2-200

2-20

613-50137-01 Rev A Command Reference for FS980M Series 501

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE MST INSTANCE PATH-COST

To return the path cost to its default value on instance 3, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no spanning-tree mst instance 3 path-cost

Commands

instance vlan (MSTP)

spanning-tree mst instance

spanning-tree mst instance priority

spanning-tree mst instance restricted-role

spanning-tree mst instance restricted-tcn

613-50137-01 Rev A Command Reference for FS980M Series 502

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE MST INSTANCE PRIORITY

spanning-tree mst instance priority

Overview Use this command in Interface Configuration mode for a switch port interface only

to set the port priority for an MST instance (MSTI).

Use the no variant of this command to restore the default priority value (128).

Syntax spanning-tree mst instance <instance-id> priority <priority>

no spanning-tree mst instance <instance-id> [priority]

Default The default is 128.

Mode Interface Configuration mode for a switch port interface.

Usage This command sets the value of the priority field contained in the port identifier.

The MST algorithm uses the port priority when determining the root port for the

switch in the MSTI. The port with the lowest value has the highest priority, so it will

be chosen as root port over a port that is equivalent in all other aspects but with a

higher priority value.

Examples To set the priority to 112 on instance 3, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# spanning-tree mst instance 3 priority 112

To return the priority to its default value of 128 on instance 3, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no spanning-tree mst instance 3 priority

Commands

instance vlan (MSTP)

spanning-tree priority (port priority)

spanning-tree mst instance

spanning-tree mst instance path-cost

spanning-tree mst instance restricted-role

spanning-tree mst instance restricted-tcn

Parameter Description

<instance-id>Specify an MSTP instance in the range 1-5.

<priority>This must be a multiple of 16 and within the range <0-240>. A

lower priority indicates greater likelihood of the port becoming

the root port.

613-50137-01 Rev A Command Reference for FS980M Series 503

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE MST INSTANCE RESTRICTED-ROLE

spanning-tree mst instance restricted-role

Overview Use this command in Interface Configuration mode for a switch port interface only

to enable the restricted role for an MSTI (Multiple Spanning Tree Instance) on a

switch port. Configuring the restricted role for an MSTI on a switch port prevents

the switch port from becoming the root port in a spanning tree topology.

Use the no variant of this command to disable the restricted role for an MSTI on a

switch port. Removing the restricted role for an MSTI on a switch port allows the

switch port to become the root port in a spanning tree topology.

Syntax spanning-tree mst instance <instance-id> restricted-role

no spanning-tree mst instance <instance-id> restricted-role

Default The restricted role for an MSTI instance on a switch port is disabled by default.

Mode Interface Configuration mode for a switch port interface only.

Usage The root port is the port providing the best path from the bridge to the root bridge.

Use this command to disable a port from becoming a root port. Use the no variant

of this command to enable a port to become a root port. See the STP Feature

Overview and Configuration Guide for root port information.

Examples To prevent a switch port from becoming the root port, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# spanning-tree mst instance 3 restricted-role

To stop preventing the switch port from becoming the root port, use the

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no spanning-tree mst instance 3

restricted-role

Parameter Description

<instance-id>Specify an MSTP instance in the range 1-5. The MST instance must

have already been created using the instance vlan (MSTP)

command.

613-50137-01 Rev A Command Reference for FS980M Series 504

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE MST INSTANCE RESTRICTED-ROLE

Commands

instance vlan (MSTP)

spanning-tree priority (port priority)

spanning-tree mst instance

spanning-tree mst instance path-cost

spanning-tree mst instance restricted-tcn

613-50137-01 Rev A Command Reference for FS980M Series 505

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE MST INSTANCE RESTRICTED-TCN

spanning-tree mst instance restricted-tcn

Overview Use this command to prevent a switch port from propagating received topology

change notifications and topology changes to other switch ports. This is named

restricted TCN (Topology Change Notification). A TCN is a simple Bridge Protocol

Data Unit (BPDU) that a bridge sends out to its root port to signal a topology

change.

Use the no variant of this command to stop preventing the switch port from

propagating received topology change notifications and topology changes to

other switch ports for the specified MSTI (Multiple Spanning Tree Instance).

The restricted TCN setting applies only to the specified MSTI (Multiple Spanning

Tree Instance).

Syntax spanning-tree mst instance <instance-id> restricted-tcn

no spanning-tree mst instance <instance-id> restricted-tcn

Default Disabled. By default, switch ports propagate TCNs.

Mode Interface Configuration mode for a switch port interface only.

Examples To prevent a switch port from propagating received topology change notifications

and topology changes to other switch ports, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# spanning-tree mst instance 3 restricted-tcn

To stop preventing a switch port from propagating received topology change

notifications and topology changes to other switch ports, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no spanning-tree mst instance 3

restricted-tcn

Commands

instance vlan (MSTP)

spanning-tree priority (port priority)

spanning-tree mst instance

spanning-tree mst instance path-cost

spanning-tree mst instance restricted-role

Parameter Description

<instance-id>Specify an MSTP instance in the range 1-5. The MST instance must

have already been created using the instance vlan (MSTP)

command.

613-50137-01 Rev A Command Reference for FS980M Series 506

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE PATH-COST

spanning-tree path-cost

Overview Use this command in Interface Configuration mode for a switch port interface only

to set the cost of a path for the specified port. This value then combines with others

along the path to the root bridge in order to determine the total cost path value

from the particular port, to the root bridge. The lower the numeric value, the

higher the priority of the path. This applies when the port is the root port.

Use this command for RSTP, STP or MSTP. When MSTP mode is configured, this will

apply to the port’s path cost for the CIST.

Syntax spanning-tree path-cost <pathcost>

no spanning-tree path-cost

Default The default path cost values and the range of recommended path cost values

depend on the port speed, as shown in the following table from the IEEE

802.1q-2003 and IEEE 802.1d-2004 standards.

Mode Interface Configuration mode for switch port interface only.

Example awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# spanning-tree path-cost 123

Parameter Description

<pathcost><1-200000000> The cost to be assigned to the port.

Port speed Default path cost Recommended path cost range

Less than 100 Kb/s

1Mbps

10Mbps

100 Mbps

1 Gbps

10 Gbps

100 Gbps

1Tbps

10 Tbps

200,000,000

20,000,000

2,000,000

200,000

20,000

2,000

200

20,000,000-200,000,000

2,000,000-20,000,000

200,000-2,000,000

20,000-200,000

2,000-20,000

200-2, 000

20-200

2-200

2-20

613-50137-01 Rev A Command Reference for FS980M Series 507

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE PORTFAST (STP)

spanning-tree portfast (STP)

Overview Use this command in Interface Configuration mode for a switch port interface only

to set a port as an edge-port. The portfast feature enables a port to rapidly move

to the forwarding state, without having first to pass through the intermediate

spanning tree states. This command has the same effect as the spanning-tree

edgeport (RSTP and MSTP) command, but the configuration displays differently in

the output of some show commands.

NOTE: You can run either of two additional parameters with this command. To simplify

the syntax these are documented as separate commands. See the following additional

portfast commands:

•spanning-tree portfast bpdu-filter command

•spanning-tree portfast bpdu-guard command.

You can obtain the same effect by running the spanning-tree edgeport (RSTP and

MSTP) command. However, the configuration output may display differently in

some show commands.

Use the no variant of this command to set a port to its default state (not an

edge-port).

Syntax spanning-tree portfast

no spanning-tree portfast

Default Not an edge port.

Mode Interface Configuration mode for a switch port interface only.

Usage Portfast makes a port move from a blocking state to a forwarding state, bypassing

both listening and learning states. The portfast feature is meant to be used for

ports connected to end-user devices. Enabling portfast on ports that are

connected to a workstation or server allows devices to connect to the network

without waiting for spanning-tree to converge.

For example, you may need hosts to receive a DHCP address quickly and waiting

for STP to converge would cause the DHCP request to time out. Ensure you do not

use portfast on any ports connected to another device to avoid creating a

spanning-tree loop on the network.

Use this command on a switch port that connects to a LAN with no other bridges

attached. An edge port should never receive BPDUs. Therefore if an edge port

receives a BPDU, the portfast feature takes one of three actions.

• Cease to act as an edge port and pass BPDUs as a member of a spanning tree

network (spanning-tree portfast (STP) command disabled).

• Filter out the BPDUs and pass only the data and continue to act as a edge

port (spanning-tree portfast bpdu-filter command enabled).

• Block the port to all BPDUs and data (spanning-tree portfast bpdu-guard

command enabled).

613-50137-01 Rev A Command Reference for FS980M Series 508

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE PORTFAST (STP)

Example awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# spanning-tree portfast

Commands

spanning-tree edgeport (RSTP and MSTP)

show spanning-tree

spanning-tree portfast bpdu-filter

spanning-tree portfast bpdu-guard

613-50137-01 Rev A Command Reference for FS980M Series 509

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE PORTFAST BPDU-FILTER

spanning-tree portfast bpdu-filter

Overview This command sets the bpdu-filter feature and applies a filter to any BPDUs (Bridge

Protocol Data Units) received. Enabling this feature ensures that configured ports

will not transmit any BPDUs and will ignore (filter out) any BPDUs received. BPDU

Filter is not enabled on a port by default.

Using the no variant of this command to turn off the bpdu-filter, but retain the

port’s status as an enabled port. If the port then receives a BPDU it will change its

role from an edge-port to a non edge-port.

Syntax (Global

Configuration)

spanning-tree portfast bpdu-filter

no spanning-tree portfast bpdu-filter

Syntax (Interface

Configuration)

spanning-tree portfast bpdu-filter {default|disable|enable}

no spanning-tree portfast bpdu-filter

Default BPDU Filter is not enabled on any ports by default.

Mode Global Configuration and Interface Configuration

Usage This command filters the BPDUs and passes only data to continue to act as an edge

port. Using this command in Global Configuration mode applies the portfast

bpdu-filter feature to all ports on the device. Using it in Interface mode applies the

feature to a specific port, or range of ports.The command will operate in both RSTP

and MSTP networks.

Use the show spanning-tree command to display status of the bpdu-filter

parameter for the switch ports.

Example To enable STP BPDU filtering in Global Configuration mode, enter the commands:

awplus# configure terminal

awplus(config)# spanning-tree portfast bpdu-filter

Parameter Description

bpdu-filter A port that has bpdu-filter enabled will not transmit any BPDUs and

will ignore any BPDUs received. This port type has one of the

following parameters (in Interface Configuration mode):

default Takes the setting that has been configured for the whole

device, i.e. the setting made from the Global

configuration mode.

disable Turns off BPDU filter.

enable Turns on BPDU filter.

613-50137-01 Rev A Command Reference for FS980M Series 510

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE PORTFAST BPDU-FILTER

To enable STP BPDU filtering in Interface Configuration mode, enter the

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# spanning-tree portfast bpdu-filter enable

Commands

spanning-tree edgeport (RSTP and MSTP)

show spanning-tree

spanning-tree portfast (STP)

spanning-tree portfast bpdu-guard

613-50137-01 Rev A Command Reference for FS980M Series 511

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE PORTFAST BPDU-GUARD

spanning-tree portfast bpdu-guard

Overview This command applies a BPDU (Bridge Protocol Data Unit) guard to the port. A port

with the bpdu-guard feature enabled will block all traffic (BPDUs and user data), if

it starts receiving BPDUs.

Use this command in Global Configuration mode to apply BPDU guard to all ports

on the device. Use this command in Interface mode for an individual interface or a

range of interfaces specified. BPDU Guard is not enabled on a port by default.

Use the no variant of this command to disable the BPDU Guard feature on a device

in Global Configuration mode or to disable the BPDU Guard feature on a port in

Interface mode.

Syntax (Global

Configuration)

spanning-tree portfast bpdu-guard

no spanning-tree portfast bpdu-guard

Syntax (Interface

Configuration)

spanning-tree portfast bpdu-guard {default|disable|enable}

no spanning-tree portfast bpdu-guard

Default BPDU Guard is not enabled on any ports by default.

Mode Global Configuration or Interface Configuration

Usage This command blocks the port(s) to all devices and data when enabled. BPDU

Guard is a port-security feature that changes how a portfast-enabled port behaves

if it receives a BPDU. When bpdu-guard is set, then the port shuts down if it

receives a BPDU. It does not process the BPDU as it is considered suspicious. When

bpdu-guard is not set, then the port will negotiate spanning-tree with the device

sending the BPDUs. By default, bpdu- guard is not enabled on a port.

You can configure a port disabled by the bpdu-guard to re-enable itself after a

specific time interval. This interval is set with the spanning-tree errdisable-timeout

interval command. If you do not use the errdisable-timeout feature, then you will

need to manually re-enable the port by using the no shutdown command.

Parameter Description

bpdu-guard A port that has bpdu-guard turned on will enter the STP blocking state

if it receives a BPDU. This port type has one of the following

parameters (in Interface Configuration mode):

default Takes the setting that has been configured for the whole

device, i.e. the setting made from the Global configuration

mode.

disable Turns off BPDU guard.

enable Turns on BPDU guard and will also set the port as an edge

port.

613-50137-01 Rev A Command Reference for FS980M Series 512

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE PORTFAST BPDU-GUARD

Use the show spanning-tree command to display the device and port

configurations for the BPDU Guard feature. It shows both the administratively

configured and currently running values of bpdu-guard.

Example To enable STP BPDU guard in Global Configuration mode, enter the below

commands:

awplus# configure terminal

awplus(config)# spanning-tree portfast bpdu-guard

To enable STP BPDU guard in Interface Configuration mode, enter the below

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# spanning-tree portfast bpdu-guard enable

Commands

spanning-tree edgeport (RSTP and MSTP)

show spanning-tree

spanning-tree portfast (STP)

spanning-tree portfast bpdu-filter

613-50137-01 Rev A Command Reference for FS980M Series 513

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE PRIORITY (BRIDGE PRIORITY)

spanning-tree priority (bridge priority)

Overview Use this command to set the bridge priority for the device. A lower priority value

indicates a greater likelihood of the device becoming the root bridge.

Use this command for RSTP, STP or MSTP. When MSTP mode is configured, this will

apply to the CIST.

Use the no variant of this command to reset it to the default.

Syntax spanning-tree priority <priority>

no spanning-tree priority

Default The default priority is 32678.

Mode Global Configuration

Usage To force a particular device to become the root bridge use a lower value than other

devices in the spanning tree.

Example awplus# configure terminal

awplus(config)# spanning-tree priority 4096

Commands

spanning-tree mst instance priority

show spanning-tree

Parameter Description

<priority><0-61440> The bridge priority, which will be rounded to a multiple of

4096.

613-50137-01 Rev A Command Reference for FS980M Series 514

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE PRIORITY (PORT PRIORITY)

spanning-tree priority (port priority)

Overview Use this command in Interface Configuration mode for a switch port interface only

to set the port priority for port. A lower priority value indicates a greater likelihood

of the port becoming part of the active topology.

Use this command for RSTP, STP, or MSTP. When the device is in MSTP mode, this

will apply to the CIST.

Use the no variant of this command to reset it to the default.

Syntax spanning-tree priority <priority>

no spanning-tree priority

Default The default priority is 128.

Mode Interface Configuration mode for a switch port interface only.

Usage To force a port to be part of the active topology (for instance, become the root port

or a designated port) use a lower value than other ports on the device. (This

behavior is subject to network topology, and more significant factors, such as

bridge ID.)

Example awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# spanning-tree priority 16

Commands

spanning-tree mst instance priority

spanning-tree priority (bridge priority)

show spanning-tree

Parameter Description

<priority><0-240>, in increments of 16. The port priority, which will be rounded

down to a multiple of 16.

613-50137-01 Rev A Command Reference for FS980M Series 515

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE RESTRICTED-ROLE

spanning-tree restricted-role

Overview Use this command in Interface Configuration mode for a switch port interface only

to restrict the port from becoming a root port.

Use the no variant of this command to disable the restricted role functionality.

Syntax spanning-tree restricted-role

no spanning-tree restricted-role

Default The restricted role is disabled.

Mode Interface Configuration mode for a switch port interface only.

Example awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# spanning-tree restricted-role

613-50137-01 Rev A Command Reference for FS980M Series 516

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE RESTRICTED-TCN

spanning-tree restricted-tcn

Overview Use this command in Interface Configuration mode for a switch port interface only

to prevent TCN (Topology Change Notification) BPDUs (Bridge Protocol Data

Units) from being sent on a port. If this command is enabled, after a topology

change a bridge is prevented from sending a TCN to its designated bridge.

Use the no variant of this command to disable the restricted TCN functionality.

Syntax spanning-tree restricted-tcn

no spanning-tree restricted-tcn

Default The restricted TCN is disabled.

Mode Interface Configuration mode for a switch port interface only.

Example awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# spanning-tree restricted-tcn

613-50137-01 Rev A Command Reference for FS980M Series 517

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

SPANNING-TREE TRANSMIT-HOLDCOUNT

spanning-tree transmit-holdcount

Overview Use this command to set the maximum number of BPDU transmissions that are

held back.

Use the no variant of this command to restore the default transmit hold-count

value.

Syntax spanning-tree transmit-holdcount

no spanning-tree transmit-holdcount

Default Transmit hold-count default is 3.

Mode Global Configuration

Example awplus# configure terminal

awplus(config)# spanning-tree transmit-holdcount

613-50137-01 Rev A Command Reference for FS980M Series 518

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

SPANNING TREE COMMANDS

UNDEBUG MSTP

undebug mstp

Overview This command applies the functionality of the no debug mstp (RSTP and STP)

command.

613-50137-01 Rev A Command Reference for FS980M Series 519

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Link Aggregation

Commands

Introduction

Overview This chapter provides an alphabetical reference of commands used to configure a

static channel group (static aggregator) and dynamic channel group (LACP

channel group, etherchannel or LACP aggregator). Link aggregation is also

sometimes referred to as channeling.

NOTE: AlliedWare Plus™ supports IEEE 802.3ad link aggregation and uses the Link

Aggregation Control Protocol (LACP). LACP does not interoperate with devices that use

Port Aggregation Protocol (PAgP).

Link aggregation does not necessarily achieve exact load balancing across the links.

The load sharing algorithm is designed to ensure that any given data flow always goes

down the same link. It also aims to spread data flows across the links as evenly as

possible.

For example, for a 2 Gbps LAG that is a combination of two 1 Gbps ports, any one flow

of traffic can only ever reach a maximum throughput of 1 Gbps. However, the hashing

algorithm should spread the flows across the links so that when many flows are

operating, the full 2 Gbps can be utilized.

For a description of static and dynamic link aggregation (LACP), and configuration

examples, see the Link Aggregation Feature Overview and Configuration Guide.

Command List •“channel-group” on page 521

•“clear lacp counters” on page 523

•“debug lacp” on page 524

•“lacp global-passive-mode enable” on page 525

•“lacp port-priority” on page 526

•“lacp system-priority” on page 527

•“lacp timeout” on page 528

•“show debugging lacp” on page 530

•“show diagnostic channel-group” on page 531

613-50137-01 Rev A Command Reference for FS980M Series 520

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

•“show etherchannel” on page 532

•“show etherchannel detail” on page 533

•“show etherchannel summary” on page 534

•“show lacp sys-id” on page 535

•“show lacp-counter” on page 536

•“show port etherchannel” on page 537

•“show static-channel-group” on page 538

•“static-channel-group” on page 539

•“undebug lacp” on page 541

613-50137-01 Rev A Command Reference for FS980M Series 521

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

CHANNEL-GROUP

channel-group

Overview Use this command to either create a new dynamic channel group while at the

same time adding a port to it, or to add a port to an existing dynamic channel

group. Note that you must also set the LACP mode to be either active or passive.

You can create up to 32 dynamic (LACP) channel groups (and up to 96 static

channel groups).

Use the no variant of this command to turn off link aggregation on the device port.

You will be returned to Global Configuration mode from Interface Configuration

mode.

Syntax channel-group <dynamic-channel-group-number> mode

{active|passive}

no channel-group

Mode Interface Configuration

Usage All the device ports in a channel-group must belong to the same VLANs, have the

same tagging status, and can only be operated on as a group. All device ports

within a channel group must have the same port speed and be in full duplex mode.

Once the LACP channel group has been created, it is treated as a device port, and

can be referred to in most other commands that apply to device ports.

To refer to an LACP channel group in other LACP commands, use the channel

group number. To specify an LACP channel group (LACP aggregator) in other

commands, prefix the channel group number with po. For example, ‘po2’ refers to

the LACP channel group with channel group number 2.

Link aggregation hashes the source and destination MAC address to select a link

on which to send a packet. So packet flow between a pair of hosts always takes the

same link inside the Link Aggregation Group (LAG). The net effect is that the

bandwidth for a given packet stream is restricted to the speed of one link in the

LAG. This hashing mechanism cannot be changed.

Parameter Description

<dynamic-channel-

group-number>

<1-32> Specify a dynamic channel group number for an

LACP link. You can create up to 32 dynamic (LACP) channel

groups (in addition to up to 96 static channel groups).

active Enables initiation of LACP negotiation on a port. The port

will transmit LACP dialogue messages whether or not it

receives them from the partner device.

passive Disables initiation of LACP negotiation on a port. The port

will only transmit LACP dialogue messages if the partner

device is transmitting them, i.e., the partner is in the active

mode.

613-50137-01 Rev A Command Reference for FS980M Series 522

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

CHANNEL-GROUP

For more information about LACP, see the Link Aggregation Feature Overview and

Configuration Guide which is available on our website at alliedtelesis.com.

Examples To add device port1.0.6 to a newly created LACP channel group 2 use the

commands below:

awplus# configure terminal

awplus(config)# interface port1.0.6

awplus(config-if)# channel-group 2 mode active

To remove device port1.0.6 from any created LACP channel groups use the

command below:

awplus# configure terminal

awplus(config)# interface port1.0.6

awplus(config-if)# no channel-group

To reference channel group 2 as an interface, use the following commands:

awplus# configure terminal

awplus(config)# interface po2

awplus(config-if)#

Commands

show etherchannel

show etherchannel detail

show etherchannel summary

show port etherchannel

613-50137-01 Rev A Command Reference for FS980M Series 523

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

CLEAR LACP COUNTERS

clear lacp counters

Overview Use this command to clear all counters of all present LACP aggregators (channel

groups) or a given LACP aggregator.

Syntax clear lacp [<1-32>] counters

Mode Privileged Exec

Example awplus# clear lacp 2 counters

Parameter Description

<1-32>Channel-group number.

613-50137-01 Rev A Command Reference for FS980M Series 524

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

DEBUG LACP

debug lacp

Overview Use this command to enable all LACP troubleshooting functions.

Use the no variant of this command to disable this function.

Syntax debug lacp {all|cli|event|ha|packet|sync|timer[detail]}

no debug lacp {all|cli|event|ha|packet|sync|timer[detail]}

Mode Privileged Exec and Global Configuration

Examples awplus# debug lacp timer detail

awplus# debug lacp all

Commands

show debugging lacp

undebug lacp

Parameter Description

all Turn on all debugging for LACP.

cli Specifies debugging for CLI messages.

Echoes commands to the console.

event Specifies debugging for LACP events.

Echoes events to the console.

ha Specifies debugging for HA (High Availability) events.

Echoes High Availability events to the console.

packet Specifies debugging for LACP packets.

Echoes packet contents to the console.

sync Specified debugging for LACP synchronization.

Echoes synchronization to the console.

timer Specifies debugging for LACP timer.

Echoes timer expiry to the console.

detail Optional parameter for LACP timer-detail.

Echoes timer start/stop details to the console.

613-50137-01 Rev A Command Reference for FS980M Series 525

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

LACP GLOBAL-PASSIVE-MODE ENABLE

lacp global-passive-mode enable

Overview Use this command to enable LACP channel-groups to dynamically self-configure

when they are connected to another device that has LACP channel-groups

configured with Active Mode.

Syntax lacp global-passive-mode enable

no lacp global-passive-mode enable

Default Enabled

Mode Global Configuration

Usage Do not mix LACP configurations (manual & dynamic). When LACP global passive

mode is turned on (by using the lacp global-passive-mode enable command),

we do not recommend using a mixed configuration in a LACP channel-group; i.e.

some links are manually configured (by the channel-group command) and others

are dynamically learned in the same channel-group.

Example To enable global passive mode for LACP channel groups, use the command:

awplus(config)# lacp global-passive-mode enable

To disable global passive mode for LACP channel groups, use the command:

awplus(config)# no lacp global-passive-mode enable

Commands

show etherchannel

show etherchannel detail

613-50137-01 Rev A Command Reference for FS980M Series 526

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

LACP PORT-PRIORITY

lacp port-priority

Overview Use this command to set the priority of a device port. Ports are selected for

aggregation based on their priority, with the higher priority (numerically lower)

ports selected first.

Use the no variant of this command to reset the priority of port to the default.

Syntax lacp port-priority <1-65535>

no lacp port-priority

Default The default is 32768.

Mode Interface Configuration

Example awplus# configure terminal

awplus(config)# interface port1.0.5

awplus(config-if)# lacp port-priority 34

Parameter Description

<1-65535> Specify the LACP port priority.

613-50137-01 Rev A Command Reference for FS980M Series 527

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

LACP SYSTEM-PRIORITY

lacp system-priority

Overview Use this command to set the system priority of a local system. This is used in

determining the system responsible for resolving conflicts in the choice of

aggregation groups.

Use the no variant of this command to reset the system priority of the local system

to the default.

Syntax lacp system-priority <1-65535>

no lacp system-priority

Default The default is 32768.

Mode Global Configuration

Example awplus# configure terminal

awplus(config)# lacp system-priority 6700

Parameter Description

<1-65535> LACP system priority. Lower numerical values have higher priorities.

613-50137-01 Rev A Command Reference for FS980M Series 528

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

LACP TIMEOUT

lacp timeout

Overview Use this command to set the short or long timeout on a port. Ports will time out of

the aggregation if three consecutive updates are lost.

Syntax lacp timeout {short|long}

Default The default is long timeout (30 seconds).

Mode Interface Configuration

Usage This command enables the device to indicate the rate at which it expects to receive

LACPDUs from its neighbor.

If the timeout is set to long, then the device expects to receive an update every 30

seconds, and this will time a port out of the aggregation if no updates are seen for

90 seconds (i.e. 3 consecutive updates are lost).

If the timeout is set to short, then the device expects to receive an update every

second, and this will time a port a port out of the aggregation if no updates are

seen for 3 seconds (i.e. 3 consecutive updates are lost).

The device indicates its preference by means of the Timeout field in the Actor

section of its LACPDUs. If the Timeout field is set to 1, then the device has set the

short timeout. If the Timeout field is set to 0, then the device has set the long

timeout.

Setting the short timeout enables the device to be more responsive to

communication failure on a link, and does not add too much processing overhead

to the device (1 packet per second).

NOTE: It is not possible to configure the rate that the device sends LACPDUs; the device

must send at the rate which the neighbor indicates it expects to receive LACPDUs.

Examples The following commands set the LACP long timeout period for 30 seconds on

port1.0.2.

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# lacp timeout long

Parameter Description

timeout Number of seconds before invalidating a received LACP data unit

(DU).

short LACP short timeout. The short timeout value is 1 second.

long LACP long timeout. The long timeout value is 30 seconds.

613-50137-01 Rev A Command Reference for FS980M Series 529

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

LACP TIMEOUT

The following commands set the LACP short timeout for 1 second on port1.0.2.

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# lacp timeout short

613-50137-01 Rev A Command Reference for FS980M Series 530

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

SHOW DEBUGGING LACP

show debugging lacp

Overview Use this command to display the LACP debugging option set.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show debugging lacp

Mode User Exec and Privileged Exec

Example awplus# show debugging lacp

Output Figure 15-1: Example output from the show debugging lacp command

Commands

debug lacp

LACP debugging status:

LACP timer debugging is on

LACP timer-detail debugging is on

LACP cli debugging is on

LACP packet debugging is on

LACP event debugging is on

LACP sync debugging is on

613-50137-01 Rev A Command Reference for FS980M Series 531

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

SHOW DIAGNOSTIC CHANNEL-GROUP

show diagnostic channel-group

Overview This command displays dynamic and static channel group interface status

information. The output of this command is useful for Allied Telesis authorized

service personnel for diagnostic purposes.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show diagnostic channel-group

Mode User Exec and Privileged Exec

Example awplus# show diagnostic channel-group

Output Figure 15-2: Example output from the show diagnostic channel-group

command

Commands

show tech-support



awplus# show diagnostic channel-group



Channel Group Info based on NSM:

Note: Pos - position in hardware table

-------------------------------------------------------------

Dev Interface IfIndex Member port IfIndex Active Pos

-------------------------------------------------------------

po1 4601 port1.0.4 5004 No

po1 4601 port1.0.5 5005 No



Channel Group Info based on HSL:

Note: Pos - position in hardware table

-------------------------------------------------------------

Dev Interface IfIndex Member port IfIndex Active Pos

-------------------------------------------------------------

po1 4601 N/a



Channel Group Info based on IPIFWD:

Note: Pos - position in hardware table

-------------------------------------------------------------

Dev Interface IfIndex Member port IfIndex Active Pos

-------------------------------------------------------------

po1 4601 N/a



No error found

613-50137-01 Rev A Command Reference for FS980M Series 532

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

SHOW ETHERCHANNEL

show etherchannel

Overview Use this command to display information about a LACP channel specified by the

channel group number.

The command output also shows the thrash limiting status. If thrash limiting is

detected and the action parameter of the thrash-limiting command is set to

vlan-disable, the output will also show the VLANs on which thrashing is detected.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide, which is

available on our website at alliedtelesis.com.

Syntax show etherchannel [<1-32>]

Mode User Exec and Privileged Exec

Example awplus# show etherchannel

Output Figure 15-3: Example output from show etherchannel

Example awplus# show etherchannel 1

Output Figure 15-4: Example output from show etherchannel for a particular channel

Parameter Description

<1-32>Channel-group number.

awplus#show etherchannel

LAG Maximum : 128

LAG Static Maximum: 96

LAG Dynamic Maximum: 32

LAG Static Count : 0

LAG Dynamic Count : 1

LAG Total Count : 1

Lacp Aggregator: po1

Member:

port1.0.5

port1.0.6

awplus#show etherchannel 1

Aggregator po1 (4601)

Mac address: 00:00:00:00:00:00

Admin Key: 0001 - Oper Key 0000

Receive link count: 0 - Transmit link count: 0

Individual: 0 - Ready: 0

Partner LAG: 0x0000,00-00-00-00-00-00

Link: port1.0.1 (5001) disabled

Link: port1.0.2 (5002) disabled

613-50137-01 Rev A Command Reference for FS980M Series 533

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

SHOW ETHERCHANNEL DETAIL

show etherchannel detail

Overview Use this command to display detailed information about all LACP channels.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide, which is

available on our website at alliedtelesis.com.

Syntax show etherchannel detail

Mode User Exec and Privileged Exec

Example awplus# show etherchannel detail

Output Example output from show etherchannel detail

awplus#show etherchannel detail

Aggregator po1 (IfIndex: 4601)

Mac address: 00:00:cd:37:05:17

Admin Key: 0001 - Oper Key 0001

Receive link count: 2 - Transmit link count: 2

Individual: 0 - Ready: 1

Partner LAG: 0x8000,00-00-cd-37-02-9a,0x0001

Link: port1.0.1 (IfIndex: 8002) synchronized

Link: port1.0.2 (IfIndex: 20002) synchronized

Aggregator po2 (IfIndex: 4602)

Mac address: 00:00:cd:37:05:17

Admin Key: 0002 - Oper Key 0002

Receive link count: 2 - Transmit link count: 2

Individual: 0 - Ready: 1

Partner LAG: 0x8000,ec-cd-6d-aa-c8-56,0x0002

Link: port1.0.3 (IfIndex: 8001) synchronized

Link: port1.0.4 (IfIndex: 20001) synchronized

613-50137-01 Rev A Command Reference for FS980M Series 534

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

SHOW ETHERCHANNEL SUMMARY

show etherchannel summary

Overview Use this command to display a summary of all LACP channels.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide, which is

available on our website at alliedtelesis.com.

Syntax show etherchannel summary

Mode User Exec and Privileged Exec

Example awplus# show etherchannel summary

Output Example output from show etherchannel summary



awplus#show etherchannel summary

Aggregator po10 (IfIndex: 4610)

Admin Key: 0010 - Oper Key 0010

Link: port1.0.1 (IfIndex: 7007) synchronized

Link: port1.0.2 (IfIndex: 8007) synchronized

Link: port1.0.3 (IfIndex: 11007) synchronized

613-50137-01 Rev A Command Reference for FS980M Series 535

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

SHOW LACP SYS-ID

show lacp sys-id

Overview Use this command to display the LACP system ID and priority.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide, which is

available on our website at alliedtelesis.com.

Syntax show lacp sys-id

Mode User Exec and Privileged Exec

Example awplus# show lacp sys-id

Output Example output from show lacp sys-id

System Priority: 0x8000 (32768)

MAC Address: 0200.0034.5684

613-50137-01 Rev A Command Reference for FS980M Series 536

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

SHOW LACP-COUNTER

show lacp-counter

Overview Use this command to display the packet traffic on all ports of all present LACP

aggregators, or a given LACP aggregator.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide, which is

available on our website at alliedtelesis.com.

Syntax show lacp-counter [<1-32>]

Mode User Exec and Privileged Exec

Example awplus# show lacp-counter 2

Output Example output from show lacp-counter

Parameter Description

<1-32>Channel-group number.

% Traffic statistics

Port LACPDUs Marker Pckt err

Sent Recv Sent Recv Sent Recv

% Aggregator po2 (IfIndex: 4604)

port1.0.2 0 0 0 0 0 0

613-50137-01 Rev A Command Reference for FS980M Series 537

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

SHOW PORT ETHERCHANNEL

show port etherchannel

Overview Use this command to show LACP details of the device port specified.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide, which is

available on our website at alliedtelesis.com.

Syntax show port etherchannel <port>

Mode User Exec and Privileged Exec

Example awplus# show port etherchannel port1.0.2

Output Example output from show port etherchannel

Parameter Description

<port> Name of the device port to display LACP information about.

awplus#show port etherchannel port1.0.2

LACP link info: port1.0.2 - 7007

Link: port1.0.2 (IfIndex: 7007)

Aggregator: po10 (IfIndex: 4610)

Receive machine state: Current

Periodic Transmission machine state: Slow periodic

Mux machine state: Collecting/Distributing

Actor Information: Partner Information:

Selected ................. Selected Partner Sys Priority ....... 0x8000

Physical Admin Key .............. 2 Partner System .. ec-cd-6d-d1-64-d0

Port Key ....................... 10 Port Key ....................... 10

Port Priority ............... 32768 Port Priority ............... 32768

Port Number .................. 7007 Port Number .................. 5001

Mode ....................... Active Mode ....................... Active

Timeout ...................... Long Timeout ...................... Long

Individual .................... Yes Individual .................... Yes

Synchronised .................. Yes Synchronised .................. Yes

Collecting .................... Yes Collecting .................... Yes

Distributing .................. Yes Distributing .................. Yes

Defaulted ...................... No Defaulted ...................... No

Expired ........................ No Expired ........................ No

613-50137-01 Rev A Command Reference for FS980M Series 538

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

SHOW STATIC-CHANNEL-GROUP

show static-channel-group

Overview Use this command to display all configured static channel groups and their

corresponding member ports. Note that a static channel group is the same as a

static aggregator.

The command output also shows the thrash limiting status. If thrash limiting is

detected and the action parameter of the thrash-limiting command is set to

vlan-disable, the output will also show the VLANs on which thrashing is detected.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide, which is

available on our website at alliedtelesis.com.

Syntax show static-channel-group

Mode User Exec and Privileged Exec

Example awplus# show static-channel-group

Output Example output from show static-channel-group

Commands

static-channel-group

% LAG Maximum : 128

% LAG Static Maximum: 96

% LAG Dynamic Maximum: 32

% LAG Static Count : 2

% LAG Dynamic Count : 2

% LAG Total Count : 4

% Static Aggregator: sa2

% Member:

port1.0.1

% Static Aggregator: sa3

% Member:

port1.0.2

613-50137-01 Rev A Command Reference for FS980M Series 539

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

STATIC-CHANNEL-GROUP

static-channel-group

Overview Use this command to create a static channel group, or add a member port to an

existing static channel group. Static channel groups are also known as static

aggregators.

You can create up to 96 static channel groups (and up to 32 dynamic channel

groups).

Use the no variant of this command to remove the device port from the static

channel group.

Syntax static-channel-group <static-channel-group-number>

[member-filters]

no static-channel-group

Mode Interface Configuration

Usage This command adds the device port to the static channel group with the specified

channel group number. If the channel group does not exist, it is created, and the

port is added to it. The no prefix detaches the port from the static channel group.

If the port is the last member to be removed, the static channel group is deleted.

All the ports in a channel group must have the same VLAN configuration: they

must belong to the same VLANs and have the same tagging status, and can only

be operated on as a group.

Once the static channel group has been created, it is treated as a device port, and

can be referred to in other commands that apply to device ports.

To refer to a static channel group in other static channel group commands, use the

channel group number. To specify a static channel group in other commands,

prefix the channel group number with sa. For example, ‘sa2’ refers to the static

channel group with channel group number 2.

Examples To define static channel group 2 on a device port, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# static-channel-group 2

Parameter Description

<static-channel-

group-number>

<1-96> Static channel group number.

member-filters Allow QoS and ACL settings to be configured on the

aggregator’s individual member ports, instead of the

aggregator itself. This configuration is required when using

QoS Storm Protection on a static aggregator.

613-50137-01 Rev A Command Reference for FS980M Series 540

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

STATIC-CHANNEL-GROUP

To reference static channel group 2 as an interface, use the commands:

awplus# configure terminal

awplus(config)# interface sa2

awplus(config-if)#

To make it possible to use QoS Storm Protection on static channel group 2 on

port1.0.6, with an ACL named “test-acl”, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.6

awplus(config-if)# static-channel-group 2 member-filters

awplus(config-if)# access-group test-acl

Commands

show static-channel-group

613-50137-01 Rev A Command Reference for FS980M Series 541

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

LINK AGGREGATION COMMANDS

UNDEBUG LACP

undebug lacp

Overview This command applies the functionality of the no debug lacp command.

613-50137-01 Rev A Command Reference for FS980M Series 542

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Power over

Ethernet

Commands

Introduction

Overview This chapter contains an alphabetical list of commands used to configure Power

over Ethernet (PoE). Each command contains a functional description and shows

examples of configuration and output screens for show commands. These

commands are only supported on PoE capable ports. An error message will display

on the console if you enter a PoE command on a port that does not support PoE.

The following documents offer further information for configuring PoE on

AlliedWare Plus switches.

•the PoE Feature Overview and Configuration_Guide.

•the Support for Allied Telesis Enterprise_MIBs_in AlliedWare Plus, for

information about which PoE MIB objects are supported.

•the SNMP Feature Overview and Configuration_Guide, for information about

SNMP traps.

Power over Ethernet (PoE) is a technology allowing devices such as security

cameras to receive power over LAN cabling.

The Powered Device (PD) referred to throughout this chapter is a PoE or PoE+

powered device, such as an IP phone or a Wireless Access Point (WAP).

Command List •“clear power-inline counters interface” on page 544

•“debug power-inline” on page 545

•“power-inline allow-legacy” on page 547

•“power-inline description” on page 548

•“power-inline enable” on page 549

•“power-inline max” on page 550

•“power-inline priority” on page 552

•“power-inline usage-threshold” on page 554

•“service power-inline” on page 555

613-50137-01 Rev A Command Reference for FS980M Series 543

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

•“show debugging power-inline” on page 556

•“show power-inline” on page 557

•“show power-inline counters” on page 560

•“show power-inline interface” on page 562

•“show power-inline interface detail” on page 564

613-50137-01 Rev A Command Reference for FS980M Series 544

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

CLEAR POWER-INLINE COUNTERS INTERFACE

clear power-inline counters interface

Overview This command will clear the counters from a specified port, a range of ports, or all

ports on the switch. If no ports are entered then PoE counters for all ports are

cleared. It will also clear all Power over Ethernet (PoE) counters supported by the

Power Ethernet MIB (RFC 3621).

Syntax clear power-inline counters interface [<port-list>]

Mode Privileged Exec

Usage The PoE counters are displayed with the show power-inline counters command.

Examples To clear the PoE counters for port1.0.2 only, use the following command:

awplus# clear power-inline counters interface port1.0.2

To clear the PoE counters for port1.0.5 through port1.0.8, use the following

command:

awplus# clear power-inline counters interface

port1.0.5-port1.0.8

To clear the PoE counters for all ports, use the following command:

awplus# clear power-inline counters interface

Validation

Commands

show power-inline counters

Parameter Description

<port-list>Selects the port or ports whose counters are to be cleared.

613-50137-01 Rev A Command Reference for FS980M Series 545

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

DEBUG POWER-INLINE

debug power-inline

Overview This command enables debugging display for messages that are specific to Power

over Ethernet (PoE).

Use the no variant of this command to disable the specified PoE debugging

messages.

Syntax debug power-inline [all|event|info|power]

no debug power-inline [all|event|info|power]

Default No debug messages are enabled by default.

Mode Privileged Exec

Usage Use the terminal monitor command to display PoE debug messages on the

console.

Use the show debugging power-inline command to show the PoE debug

configuration.

Examples To enable PoE debugging and start the display of PoE event and info debug

messages on the console, use the following commands:

awplus# terminal monitor

awplus# debug power-inline event info

To enable PoE debugging and start the display of all PoE debugging messages on

the console, use the following commands:

awplus# terminal monitor

awplus# debug power-inline all

To stop the display of PoE info debug messages on the console, use the following

command:

awplus# no debug power-inline info

To disable all PoE debugging and stop the display of any PoE debugging messages

on the console, use the following command:

awplus# no debug power-inline all

Parameter Description

all Displays all (event, info, nsm, power) debug messages.

event Displays event debug information, showing any error conditions

that may occur during PoE operation.

info Displays informational level debug information, showing high-level

essential debugging, such as information about message types.

power Displays power management debug information.

613-50137-01 Rev A Command Reference for FS980M Series 546

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

DEBUG POWER-INLINE

Commands

show debugging power-inline

terminal monitor

613-50137-01 Rev A Command Reference for FS980M Series 547

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

POWER-INLINE ALLOW-LEGACY

power-inline allow-legacy

Overview This command enables detection of pre-IEEE 802.3af Power Ethernet standard

legacy Powered Devices (PDs).

The no variant of this command disables detection of pre-IEEE 802.3af Power

Ethernet standard legacy Powered Devices (PDs).

Syntax power-inline allow-legacy

no power-inline allow-legacy

Default Detection of legacy PDs is enabled on all ports

Mode Global Configuration

Examples To disable detection of legacy PDs, use the following commands:

awplus# configure terminal

awplus(config)# no power-inline allow-legacy

To enable detection of legacy PDs, use the following commands:

awplus# configure terminal

awplus(config)# power-inline allow-legacy

Validation

Commands

show power-inline

show running-config power-inline

613-50137-01 Rev A Command Reference for FS980M Series 548

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

POWER-INLINE DESCRIPTION

power-inline description

Overview This command adds a description for a Powered Device (PD) connected to a PoE

port.

The no variant of this command clears a previously entered description for a

connected PD, resetting the PD description to the default (null).

Syntax power-inline description <pd-description>

no power-inline description

Default No description for a connected PD is set by default.

Mode Interface Configuration

Usage Select a PoE port, a list of PoE ports, or a range of PoE ports with the preceding

interface (to configure) command. If you specify a range or list of ports they must

all be PoE capable ports.

Examples To add the description “Desk Phone” for a connected PD on port1.0.2, use the

following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# power-inline description Desk Phone

To clear the description for the connected PD on port1.0.2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no power-inline description

Commands

show power-inline interface

show running-config power-inline

Parameter Description

<pd-description>Description of the PD connected to the PoE capable port

(with a maximum 256 character string limit per PD

description).

613-50137-01 Rev A Command Reference for FS980M Series 549

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

POWER-INLINE ENABLE

power-inline enable

Overview This command enables Power over Ethernet (PoE) to detect a connected Powered

Device (PD) and supply power.

The no variant of this command disables PoE functionality on the selected PoE

port(s). No power is supplied to a connected PD after PoE is disabled on the

selected PoE port(s).

Ports still provide Ethernet connectivity after PoE is disabled.

Syntax power-inline enable

no power-inline enable

Default PoE is enabled by default on all ports

Mode Interface Configuration for one or more ports.

Usage No PoE log messages are generated for ports on which PoE is disabled.

Examples To disable PoE on port1.0.1 to port1.0.4, use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.1-port1.0.4

awplus(config-if)# no power-inline enable

To enable PoE on port1.0.1 to port1.0.4, use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.1-port1.0.4

awplus(config-if)# power-inline enable

Commands

show power-inline

show power-inline interface

show power-inline interface detail

show running-config power-inline

613-50137-01 Rev A Command Reference for FS980M Series 550

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

POWER-INLINE MAX

power-inline max

Overview This command sets the maximum power allocated to a Power over an Ethernet

(PoE and PoE+) port. The amount of power actually supplied to the port depends

on the power requirements of the connected PD. It is also a function of the total

PoE power loading on the switch and the PoE priority set for the port by the

power-inline priority command. However this command (power-inline max) does

apply a maximum value to the power that the port is able to supply.

Note that the value set by this command will be the figure the switch will use when

apportioning the power budget for its ports. For example, if 15.4 W is assigned to

a port whose PD only consumes 5 W, the switch will reserve the full 15.4 W for this

port when determining its total power PoE power requirement.

The no variant of this command sets the maximum power supplied to a PoE port

to the default, which is set to the maximum power limit for the class of the

connected Powered Device (PD).

Syntax power-inline max <4000-30000>

no power-inline max

Default The switch supplies the maximum power limit for the class of the PD connected to

the port by default.

NOTE: See the PoE Feature Overview and Configuration Guide for further information

about power classes.

Mode Interface Configuration for one or more ports. If you specify a range or list of ports,

they must all be PoE capable ports.

Usage If you select a range of PoE ports in Interface Configuration mode before issuing

this command, then each port in the range selected will have the same maximum

power value configured. If the PoE port attempts to draw more than the maximum

power, this is logged and all power is removed.

Note that the value entered is rounded up to the next value supported by the

hardware. The actual value used is displayed after you enter the command, such as

in the following sample console output:

Parameter Description

<4000-30000>The maximum power supplied to a PoE port in milliwatts

(mW).

613-50137-01 Rev A Command Reference for FS980M Series 551

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

POWER-INLINE MAX

See the LLDP Feature Overview and Configuration Guide for information about

power monitoring at the PD.

Note the difference in power supplied from the PSE to the power available at the

PD due to line loss.

See the PoE Feature Overview and Configuration Guide for further information

about the difference between the power supplied from the PSE and the power

available at the PD.

Examples To set the maximum power supplied to ports in the range port1.0.1 to port1.0.4 to

6450mW per port, use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2-port1.0.4

awplus(config-if)# power-inline max 6450

To clear the user-configured maximum power supplied to port1.0.1, and revert to

using the default maximum power, use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.1

awplus(config-if)# no power-inline max

Commands

show power-inline interface

show running-config power-inline



awplus#configure terminal



awplus(config)#interface port1.0.1



awplus(config-if)#power-line max 5300



% The maximum power has been rounded to 5450mW in hardware.

613-50137-01 Rev A Command Reference for FS980M Series 552

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

POWER-INLINE PRIORITY

power-inline priority

Overview This command sets the Power over Ethernet (PoE) priority level of a PoE port to one

of three available priority levels:

•low

•high

•critical

The IE200-6 Series switches are able to supply 802.3at (PoE+) power levels to all

their PoE-capable ports. This command prioritizes ports if necessary, however this

should not be necessary on an IE200-6 Series switch.

The no variant of this command restores the PoE port priority to the default (low).

Syntax power-inline priority {low|high|critical}

no power-inline priority

Default The default priority is low for all PoE ports

Mode Interface Configuration

Usage Select a PoE port, a list of PoE ports, or a range of PoE ports with the preceding

interface (to configure) command. If you specify a range or list of ports they must

all be PoE capable ports.

PoE ports with higher priorities are given power before PoE ports with lower

priorities. If the priorities for two PoE ports are the same then the lower numbered

PoE port is given power before the higher numbered PoE port.

See the PoE Feature Overview and Configuration Guide for further information

about PoE priority.

Parameter Description

low The lowest priority for a PoE enabled port (default). PoE ports

set to low only receive power if all the PoE ports assigned to

the other two levels are already receiving power.

high The second highest priority for a PoE enabled port. PoE ports

set to high receive power only if all the ports set to critical

are already receiving power.

critical The highest priority for a PoE enabled port. PoE ports set to

critical are guaranteed power before any ports assigned to

the other two priority levels. Ports assigned to the other

priority levels receive power only if all critical ports are

receiving power.

613-50137-01 Rev A Command Reference for FS980M Series 553

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

POWER-INLINE PRIORITY

Examples To set the priority level to high on port1.0.1 to port1.0.4, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.1-port1.0.4

awplus(config-if)# power-inline priority high

To reset the priority level to the default of low on port1.0.1 to port1.0.4, use the

following commands:

awplus# configure terminal

awplus(config)# interface port1.0.1-port1.0.4

awplus(config-if)# no power-inline priority

Commands

power-inline usage-threshold

show power-inline

show power-inline interface

show running-config power-inline

613-50137-01 Rev A Command Reference for FS980M Series 554

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

POWER-INLINE USAGE-THRESHOLD

power-inline usage-threshold

Overview This command sets the level at which the switch will issue a message that the

power supplied to all Powered Devices (PDs) has reached a critical level of the

nominal power rating for the switch. The level is set as a percentage of total

available power.

The no variant of this command resets the notification usage-threshold to the

default (80% of the nominal power rating).

Syntax power-inline usage-threshold <1-99>

no power-inline usage-threshold

Default The default power usage threshold is 80% of the nominal power rating

Mode Global Configuration

Usage Use the snmp-server enable trap command to configure SNMP notification. An

SNMP notification is sent when the usage-threshold, as configured in the example,

is exceeded.

Examples To generate SNMP notifications when power supplied exceeds 70% of the nominal

power rating, use the following commands:

awplus# configure terminal

awplus(config)# snmp-server enable trap power-inline

awplus(config)# power-inline usage-threshold 70

To reset the notification threshold to the default (80% of the nominal power

rating), use the following commands:

awplus# configure terminal

awplus(config)# no power-inline usage-threshold

Commands

snmp-server enable trap

show power-inline interface

show running-config power-inline

Parameter Description

<1-99>The usage-threshold percentage configured with this

command.

613-50137-01 Rev A Command Reference for FS980M Series 555

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

SERVICE POWER-INLINE

service power-inline

Overview This command enables Power over Ethernet (PoE) globally on the switch, for all

PoE ports.

Syntax service power-inline

no service power-inline

Default PoE functionality is enabled by default

Mode Global Configuration

Examples To disable PoE, use the following commands:

awplus# configure terminal

awplus(config)# no service power-inline

To re-enable PoE, if PoE has been disabled, use the following commands:

awplus# configure terminal

awplus(config)# service power-inline

Commands

show power-inline

show running-config power-inline

613-50137-01 Rev A Command Reference for FS980M Series 556

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

SHOW DEBUGGING POWER-INLINE

show debugging power-inline

Overview This command displays Power over Ethernet (PoE) debug settings.

Syntax show debugging power-inline

Mode User Exec and Privileged Exec

Example To display PoE debug settings, use the following command:

awplus# show debugging power-inline

Output Figure 16-1: Example output from the show debugging power-inline

command

Commands

debug power-inline

terminal monitor

awplus#show debugging power-inline

PoE Debugging status:

PoE Informational debugging is disabled

PoE Event debugging is disabled

PoE Power Management debugging is disabled



PoE NSM debugging is enabled

613-50137-01 Rev A Command Reference for FS980M Series 557

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

SHOW POWER-INLINE

show power-inline

Overview This command displays the Power over Ethernet (PoE) status for all ports.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show power-inline

Mode User Exec and Privileged Exec

Example To display the PoE status for all ports, use the following command:

awplus# show power-inline

Output Figure 16-2: Example output from show power-inline

awplus#show power-inline

PoE Status:



Nominal Power: 370W

Power Allocated: 246W



Actual Power Consumption: 151W

Operational Status: On

Power Usage Threshold: 80% (296W)



PoE Interface:

Interface Admin Pri Oper Power Device Class Max(mW)

port1.0.1 Enabled Low Powered 3840 n/a 1 4000 [C]

port1.0.2 Enabled High Powered 6720 n/a 2 7000 [C]

port1.0.3 Enabled Low Powered 14784 n/a 3 15400 [C]

port1.0.4 Enabled Crit Powered 14784 n/a 3 15400 [C]

port1.0.5 Enabled Crit Powered 3840 n/a 1 4000 [C]

...

Table 1: Parameters in the show power-inline command output

Parameter Description

Nominal Power The nominal power available on the switch in watts (W).

Power Allocated The current power allocated in watts (W) that is available to

be drawn by any connected Powered Devices (PDs). This is

updated every 5 seconds.

Actual Power

Consumption

The current power consumption in watts (W) drawn by all

connected Powered Devices (PDs). This is updated every 5

seconds.

613-50137-01 Rev A Command Reference for FS980M Series 558

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

SHOW POWER-INLINE

Operational Status The operational status of the PSU hardware when this

command was issued:

•On if the PSU is installed and switched on.

•Off when the PSU is switched off (an RPS may be

connected to the switch to power PoE instead of the

PSU).

•Fault when there is an issue with the PSU hardware.

Power Usage Threshold

(%)

The configured SNMP trap / log threshold, as configured

from a power-inline usage-threshold command.

Interface The PoE port(s) in the format portx.y.z, where x is the device

number, y is the module number within the device, and z is

the PoE port number within the module.

Admin The administrative state of PoE on a PoE port, either

Enabled or Disabled.

Pri The current PoE priorities for PoE ports, as configured using

the power-inline priority command:

•Low is the lowest priority (this is the default).

•High is the second highest priority.

•Crit (critical) is the highest priority.

If the switch cannot supply all ports, it will supply critical

ports, then high-priority ports, then low-priority ports.

Oper The current PoE port state when this command was issued:

•Powered displays if there is a PD connected and power

is being supplied.

•Denied displays if supplying power would make the

switch go over the power budget.

•Off displays if the port is not supplying power but has

not been denied power by the switch. This is the default

state for ports that are not connected to a PD.

•Disabled displays if the PoE port is administratively

disabled.

•Syncing displays if PoE is still initializing the port when

you issue the command.

•Fault displays if there is a problem with PoE on the port.

•Unknown displays if PoE cannot determine the state of

the port.

Power The power consumption in milliwatts (mW) for the PoE

port when this command was entered.

Table 1: Parameters in the show power-inline command output (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 559

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

SHOW POWER-INLINE

Commands

show power-inline counters

show power-inline interface

Device The description of the connected PD device if a description

has been added with the power-inline description

command. No description is shown for PDs not configured

with the power-inline description command.

Class The class of the connected PD, if power is being supplied to

the PD.

Max (mW) The power in milliwatts (mW) allocated for the PoE port.

Additionally, note the following as displayed per PoE port:

•[U] if the power limit for a port was user configured (with

the power-inline max command).

•[L] if the power limit for a port was supplied by LLDP.

•[C] if the power limit for a port was supplied by the PD

class.

Table 1: Parameters in the show power-inline command output (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 560

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

SHOW POWER-INLINE COUNTERS

show power-inline counters

Overview This command displays Power over Ethernet (PoE) event counters for ports on the

Power Sourcing Equipment (PSE). The PoE event counters displayed can also be

accessed by objects in the PoE MIB (RFC 3621). See the MIB Objects Feature

Overview and Configuration Guide for information about which PoE MIB objects

are supported.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show power-inline counters [<port-list>]

Mode User Exec and Privileged Exec

Examples To display all PoE event counters for all PoE ports, use the command:

awplus# show power-inline counters

To display the PoE event counters for the port range 1.0.1 to 1.0.3, use the

command:

awplus# show power-inline counters interface port1.0.1-1.0.3

Output Figure 16-3: Example output from the show power-inline counters command

Parameter Description

<port-list>Enter the PoE port(s) to display PoE event counters for them.

awplus#show power-inline counters interface port1.0.1-port1.0.3

PoE Counters:

Interface MPSAbsent Overload Short Invalid Denied

port1.0.1 0 0 0 0 0

port1.0.2 0 0 0 0 0

port1.0.3 0 0 0 0 0

Table 2: Parameters in the show power-inline counters command output

Parameter Description

Interface The PoE port(s) in the format portx.y.z, where x is the device

number, y is the module number within the device, and z is the

PoE port number within the module.

MPSAbsent The number of instances when the PoE MPS (Maintain Power

Signature) signal has been lost. The PoE MPS signal is lost when a

PD is disconnected from the PSE. Also increments

pethPsePortMPSAbsentCounter in the PoE MIB.

613-50137-01 Rev A Command Reference for FS980M Series 561

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

SHOW POWER-INLINE COUNTERS

Commands

clear power-inline counters interface

show power-inline

show power-inline interface

Overload The number of instances when a PD exceeds its configured power

limit (as configured by the power-inline max command). Also

increments pethPsePortOverLoadCounter in the PoE MIB.

Short The number of short circuits that have happened with a PD. Also

increments pethPsePortShortCounter in the PoE MIB.

Invalid The number of times a PD with an Invalid Signature (where the PD

has an open or short circuit, or is a legacy PD) is detected. Also

increments pethPseInvalidSignatureCounter in the PoE

MIB.

Denied The number of times a PD has been refused power due to power

budget limitations for the PSE. Also increments

pethPsePortPowerDeniedCounter in the PoE MIB.

Table 2: Parameters in the show power-inline counters command output

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 562

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

SHOW POWER-INLINE INTERFACE

show power-inline interface

Overview This command displays a summary of Power over Ethernet (PoE) information for

specified ports. If no ports are specified then PoE information is displayed for all

ports.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show power-inline interface [<port-list>]

Mode User Exec and Privileged Exec

Example To display the PoE port-specific information for all PoE ports on the switch, use the

following command:

awplus# show power-inline interface

To display the PoE port specific information for the port range1.0.1 to 1.0.4, use the

following command:

awplus# show power-inline interface port1.0.1-port1.0.4

Output Figure 16-4: Example output from the show power-inline interface command

Parameter Description

<port-list>Enter the PoE port(s) to display PoE specific information in the show

output.

awplus#show power-inline interface port1.0.1-port1.0.4

Interface Admin Pri Oper Power Device Class Max(mW)

port1.0.1 Disabled Low Disabled 0 n/a n/a n/a

port1.0.2 Enabled High Powered 3840 Desk Phone 1 5000 [U]

port1.0.3 Enabled Crit Powered 6720 AccessPoint 2 7000 [C]

port1.0.4 Disabled Low Disabled 0 n/a n/a n/a

Table 3: Parameters in the show power-inline interface command output

Parameter Description

Interface The PoE port(s) in the format portx.y.z, where x is the device

number, y is the module number within the device, and z is the

PoE port number within the module.

Admin The administrative state of PoE on a PoE port, either Enabled or

Disabled.

613-50137-01 Rev A Command Reference for FS980M Series 563

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

SHOW POWER-INLINE INTERFACE

Commands

show power-inline

show power-inline interface detail

Pri The current PoE priorities for PoE ports on the PSE, as configured

from a power-inline priority command:

•Low displays when the low parameter is issued. The lowest

priority for a PoE enabled port (default).

•High displays when the high parameter is issued. The

second highest priority for a PoE enabled port.

•Crit displays when the critical parameter is issued. The

highest priority for a PoE enabled port.

Oper The current PoE port state when this command was issued:

•Powered displays if there is a PD connected and power is

being supplied.

•Denied displays if supplying power would make the switch

go over the power budget.

•Off displays if the port is not supplying power but has not

been denied power by the switch. This is the default state for

ports that are not connected to a PD.

•Disabled displays if the PoE port is administratively disabled.

•Syncing displays if PoE is still initializing the port when you

issue the command.

•Fault displays if there is a problem with PoE on the port.

•Unknown displays if PoE cannot determine the state of the

port.

Power The power consumption in milliwatts (mW) for the PoE port

when this command was entered.

Device The description of the connected PD device if a description has

been added with the power-inline description command. No

description is shown for PDs not configured with the

power-inline description command.

Class The class of the connected PD, if power is being supplied to the

PD from the PSE.

See the PoE Feature Overview and Configuration Guide for

further information about power classes.

Max (mW) The power in milliwatts (mW) allocated for the PoE port.

Additionally, note the following is displayed per PoE port:

•[U] if the power limit for a port was user configured (with the

power-inline max command).

•[L] if the power limit for a port was supplied by LLDP.

•[C] if the power limit for a port was supplied by the PD class.

Table 3: Parameters in the show power-inline interface command output

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 564

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

SHOW POWER-INLINE INTERFACE DETAIL

show power-inline interface detail

Overview This command displays detailed information for one or more Power over Ethernet

(PoE) ports.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show power-inline interface [<port-list>] detail

Mode User Exec and Privileged Exec

Usage The power allocated to each port is listed in the Power allocated row, and is

limited by the maximum power per Powered Device (PD) class, or a user

configured power limit.

Examples To display detailed PoE port specific information for the port range 1.0.1 to 1.0.3,

use the command:

awplus# show power-inline interface port1.0.1-1.0.3 detail

Output Figure 16-5: Example output from the show power-inline interface detail

command

Parameter Description

<port-list>Enter the PoE port(s) to display information about only the specified

port or ports.

awplus#show power-inline interface port1.0.1-1.0.2 detail

Interface port1.0.1

Powered device type: Desk Phone #1

PoE admin enabled

Priority Low

Detection status: Powered

Current power consumption: 4800 mW

Powered device class: 1

Power allocated: 5000 mW (from configuration)

Detection of legacy devices is disabled

Powered pairs: Data

Interface port1.0.2

Powered device type: Access Point #3

PoE admin enabled

Priority High

Detection status: Powered

Current power consumption: 6720 mW

Powered device class: 2

Power allocated: 7000 mW (from powered device class)

Detection of legacy devices is enabled

Powered pairs: Data

613-50137-01 Rev A Command Reference for FS980M Series 565

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

SHOW POWER-INLINE INTERFACE DETAIL

Table 4: Parameters in show power-inline interface detail command output

Parameter Description

Interface The PoE port(s) in the format portx.y.z, where x is the device

number, y is the module number within the device, and z is the

PoE port number within the module.

Powered

device type:

The name of the PD, if connected and if power is being supplied

to the PD from the PSE, configured with the power-inline

description command. n/a displays if a description has not been

configured for the PD.

PoE admin The administrative state of PoE on a PoE capable port, either

Enabled or Disabled as configured from the power-inline enable

command or the no power-inline enable command

respectively.

Priority The PoE priority of a port, which is either Low, or High, or

Critical, as configured by the power-inline priority command.

Detection

status:

The current PSE PoE port state when this command was issued:

•Powered displays when there is a PD connected and power is

being supplied from the PSE.

•Denied displays when supplying power would make the PSE

go over the power budget.

•Disabled displays when the PoE port is administratively

disabled.

•Off displays when PoE has been disabled for the port.

•Fault displays when a PSE goes over its power allocation.

Current power

consumption:

The power consumption for the PoE port when this command

was entered. Note that the power consumption may have

changed since the command was entered and the power is

displayed.

Powered

device class:

The class of the connected PD if connected, and if power is being

supplied to the PD from the PSE.

See the PoE Feature Overview and Configuration Guide for

further information about power classes.

Power

allocated:

The power in milliwatts (mW) allocated for the PoE port.

Additionally, note the following as displayed per PoE port:

•[U] if the power limit for a port was user configured (with the

power-inline max command).

•[L] if the power limit for a port was supplied by LLDP.

•[C] if the power limit for a port was supplied by the PD class.

Detection of

legacy

devices is

The status of legacy PoE detection on the PoE port (enabled or

disabled), as configured for the PoE port with the power-inline

allow-legacy command.

Powered

pairs:

The IEEE 802.3af and IEEE 802.3at standards allow for either data

or spare twisted pairs to be used to transfer power to a PD.

613-50137-01 Rev A Command Reference for FS980M Series 566

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

POWER OVER ETHERNET COMMANDS

SHOW POWER-INLINE INTERFACE DETAIL

Commands

show power-inline

show power-inline interface

613-50137-01 Rev A Command Reference for FS980M Series 567

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Part 3: Layer Three, Switching and

Routing

613-50137-01 Rev A Command Reference for FS980M Series 568

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP Addressing and

Protocol Commands

Introduction

Overview This chapter provides an alphabetical reference of commands used to configure

various IP features, including the following protocols:

• Address Resolution Protocol (ARP)

For more information, see the IP Feature Overview and Configuration Guide.

Command List •“arp-aging-timeout” on page 570

•“arp (IP address MAC)” on page 571

•“arp log” on page 572

•“arp-reply-bc-dmac” on page 575

•“clear arp-cache” on page 576

•“debug ip packet interface” on page 577

•“ip address (IP Addressing and Protocol)” on page 579

•“ip gratuitous-arp-link” on page 581

•“ip limited-local-proxy-arp” on page 583

•“ip local-proxy-arp” on page 584

•“ip proxy-arp” on page 585

•“local-proxy-arp” on page 586

•“ip unreachables” on page 587

•“ping” on page 589

•“show arp” on page 590

•“show debugging ip packet” on page 592

•“show ip interface” on page 594

•“show ip sockets” on page 595

613-50137-01 Rev A Command Reference for FS980M Series 569

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

•“show ip traffic” on page 598

•“tcpdump” on page 604

•“traceroute” on page 605

•“undebug ip packet interface” on page 606

613-50137-01 Rev A Command Reference for FS980M Series 570

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

ARP-AGING-TIMEOUT

arp-aging-timeout

Overview This command sets a timeout period on dynamic ARP entries associated with a

specific interface. If your device stops receiving traffic for the host specified in a

dynamic ARP entry, it deletes the ARP entry from the ARP cache after this timeout

is reached.

Your device times out dynamic ARP entries to ensure that the cache does not fill

with entries for hosts that are no longer active. Static ARP entries are not aged or

automatically deleted.

By default the time limit for dynamic ARP entries is 300 seconds on all interfaces.

The no variant of this command sets the time limit to the default of 300 seconds.

Syntax arp-aging-timeout <0-432000>

no arp-aging timeout

Default 300 seconds (5 minutes)

Mode Interface Configuration for a VLAN interface.

Example To set the ARP entries on interface vlan30 to time out after two minutes, use the

commands:

awplus# configure terminal

awplus(config)# interface vlan30

awplus(config-if)# arp-aging-timeout 120

Commands

clear arp-cache

show arp

Parameter Description

<0-432000> The timeout period in seconds.

613-50137-01 Rev A Command Reference for FS980M Series 571

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

ARP (IP ADDRESS MAC)

arp (IP address MAC)

Overview This command adds a static ARP entry to the ARP cache. This is typically used to

add entries for hosts that do not support ARP or to speed up the address resolution

function for a host. The ARP entry must not already exist. Use the alias parameter

to allow your device to respond to ARP requests for this IP address.

The no variant of this command removes the static ARP entry. Use the clear

arp-cache command to remove the dynamic ARP entries in the ARP cache.

Syntax arp <ip-addr> <mac-address> [<port-number>] [alias]

no arp <ip-addr>

Mode Global Configuration

Examples To add the IP address 10.10.10.9 with the MAC address 0010.2533.4655 into the

ARP cache, and have your device respond to ARP requests for this address, use the

commands:

awplus# configure terminal

awplus(config)# arp 10.10.10.9 0010.2355.4566 alias

Commands

clear arp-cache

show arp

Parameter Description

<ip-addr> The IPv4 address of the device you are adding as a static ARP

entry.

<mac-address> The MAC address of the device you are adding as a static ARP

entry, in hexadecimal notation with the format

HHHH.HHHH.HHHH.

<port-number> The port number associated with the IP address. Specify this

when the IP address is part of a VLAN.

alias Allows your device to respond to ARP requests for the IP

address. Proxy ARP must be enabled on the interface before

using this parameter.

613-50137-01 Rev A Command Reference for FS980M Series 572

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

ARP LOG

arp log

Overview This command enables the logging of dynamic and static ARP entries in the ARP

cache. The ARP cache contains mappings of device ports, VLAN IDs, and IP

addresses to physical MAC addresses for hosts.

This command can display the MAC addresses in the ARP log either using the

notation HHHH.HHHH.HHHH, or using the IEEE standard hexadecimal notation

(HH-HH-HH-HH-HH-HH).

Use the no variant of this command to disable the logging of ARP entries.

Syntax arp log [mac-address-format ieee]

no arp log [mac-address-format ieee]

Default The ARP logging feature is disabled by default.

Mode Global Configuration

Usage You have the option to change how the MAC address is displayed in the ARP log

message. The output can either use the notation HHHH.HHHH.HHHH or

HH-HH-HH-HH-HH-HH.

Enter arp log to use HHHH.HHHH.HHHH notation.

Enter arp log mac-address-format ieee to use HH-HH-HH-HH-HH-HH notation.

Enter no arp log mac-address-format ieee to revert from HH-HH-HH-HH-HH-HH

to HHHH.HHHH.HHHH.

Enter no arp log to disable ARP logging.

To display ARP log messages use the show log | include ARP_LOG command.

Examples To enable ARP logging and specify that the MAC address in the log message is

displayed in HHHH.HHHH.HHHH notation, use the following commands:

awplus# configure terminal

awplus(config)# arp log

To disable ARP logging on the device, use the following commands:

awplus# configure terminal

awplus(config)# no arp log

Parameter Description

mac-address-format ieee Display the MAC address in the standard IEEE

format (HH-HH-HH-HH-HH-HH), instead of

displaying the MAC address with the format

HHHH.HHHH.HHHH.

613-50137-01 Rev A Command Reference for FS980M Series 573

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

ARP LOG

To enable ARP logging and specify that the MAC address in the log message is

displayed in the standard IEEE format hexadecimal notation

(HH-HH-HH-HH-HH-HH), use the following commands:

awplus# configure terminal

awplus(config)# arp log mac-address-format ieee

To leave ARP logging enabled, but stop using HH-HH-HH-HH-HH-HH format and

use HHHH.HHHH.HHHH format instead, use the following commands:

awplus# configure terminal

awplus(config)# no arp log mac-address-format ieee

To display ARP log messages, use following command:

awplus# show log | include ARP_LOG

Output Figure 17-1: Output from show log | include ARP_LOG after enabling ARP

logging using arp log. Note that this output uses

HHHH.HHHH.HHHH format.

Figure 17-2: Output from show log | include ARP_LOG after enabling ARP

logging using arp log mac-address format ieee. Note that this

output uses HH-HH-HH-HH-HH-HH format.

awplus#configure terminal

awplus(config)#arp log

awplus(config)#exit

awplus#show log | include ARP_LOG

2016 Oct 6 06:21:01 user.notice awplus HSL[1007]: ARP_LOG port1.0.1 vlan1 add 

0013.4078.3b98 (192.168.2.4)

2016 Oct 6 06:22:30 user.notice awplus HSL[1007]: ARP_LOG port1.0.1 vlan1 del 

0013.4078.3b98 (192.168.2.4)

2016 Oct 6 06:23:26 user.notice awplus HSL[1007]: ARP_LOG port1.0.1 vlan1 add 

0030.940e.136b (192.168.2.20)

2016 Oct 6 06:23:30 user.notice awplus IMISH[1830]: show log | include ARP_LOG

awplus#configure terminal

awplus(config)#arp log mac-address-format ieee

awplus(config)#exit

awplus#show log | include ARP_LOG

2016 Oct 6 06:25:28 user.notice awplus HSL[1007]: ARP_LOG port1.0.1 vlan1 add

00-17-9a-b6-03-69 (192.168.2.12)

2016 Oct 6 06:25:30 user.notice awplus HSL[1007]: ARP_LOG port1.0.1 vlan1 add

00-03-37-6b-a6-a5 (192.168.2.10)

2016 Oct 6 06:26:53 user.notice awplus HSL[1007]: ARP_LOG port1.0.1 vlan1 del

00-30-94-0e-13-6b (192.168.2.20)

2016 Oct 6 06:27:31 user.notice awplus HSL[1007]: ARP_LOG port1.0.1 vlan1 del

00-17-9a-b6-03-69 (192.168.2.12)

2016 Oct 6 06:28:09 user.notice awplus HSL[1007]: ARP_LOG port1.0.1 vlan1 del

00-03-37-6b-a6-a5 (192.168.2.10)

2016 Oct 6 06:28:14 user.notice awplus IMISH[1830]: show log | include ARP_LOG

613-50137-01 Rev A Command Reference for FS980M Series 574

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

ARP LOG

The following table lists the parameters in output of the show log | include

ARP_LOG command. The ARP log message format is:

<date> <time> <severity> <hostname> <program-name> 

ARP_LOG <port-number> <vid> <operation> <MAC> <IP>

Commands

show log

show running-config

Table 1: Parameters in output of the show log | include ARP_LOG command

Parameter Description

ARP_LOG Indicates that ARP log entry information follows.

<port-number>Indicates device port number for the ARP log entry.

<vid>Indicates the VLAN ID for the ARP log entry.

<operation>Indicates “add” if the ARP log entry displays an ARP addition.

Indicates “del” if the ARP log entry displays an ARP deletion.

<MAC>Indicates the MAC address for the ARP log entry, either in the

default hexadecimal notation (HHHH.HHHH.HHHH) or in the

IEEE standard format hexadecimal notation

(HH-HH-HH-HH-HH-HH) as specified with the arp log or the arp

log mac-address-format ieee command.

<IP>Indicates the IP address for the ARP log entry.

613-50137-01 Rev A Command Reference for FS980M Series 575

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

ARP-REPLY-BC-DMAC

arp-reply-bc-dmac

Overview Use this command to allow processing of ARP replies that arrive with a broadcast

destination MAC (ffff.ffff.ffff). This makes neighbors reachable if they send ARP

responses that contain a broadcast destination MAC.

Use the no variant of this command to turn off processing of ARP replies that arrive

with a broadcast destination MAC.

Syntax arp-reply-bc-dmac

no arp-reply-bc-dmac

Default By default, this functionality is disabled.

Mode Interface Configuration for VLAN interfaces

Example To allow processing of ARP replies that arrive on VLAN2 with a broadcast

destination MAC, use the commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# arp-reply-bc-dmac

Commands

clear arp-cache

show arp

613-50137-01 Rev A Command Reference for FS980M Series 576

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

CLEAR ARP-CACHE

clear arp-cache

Overview This command deletes dynamic ARP entries from the ARP cache. You can

optionally specify the IPv4 address of an ARP entry to be cleared from the ARP

cache.

Syntax clear arp-cache [<ip-address>]

Mode Privileged Exec

Usage To display the entries in the ARP cache, use the show arp command. To remove

static ARP entries, use the no variant of the arp (IP address MAC) command.

Example To clear all dynamic ARP entries, use the command:

awplus# clear arp-cache

To clear all dynamic ARP entries associated with the IPv4 address 192.168.1.1, use

the command:

awplus# clear arp-cache 192.168.1.1

Commands

arp (IP address MAC)

show arp

Parameter Description

<ip-address> The IPv4 address of an ARP entry that is to be cleared from the

ARP cache.

613-50137-01 Rev A Command Reference for FS980M Series 577

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

DEBUG IP PACKET INTERFACE

debug ip packet interface

Overview The debug ip packet interface command enables IP packet debug and is

controlled by the terminal monitor command.

If the optional icmp keyword is specified then ICMP packets are shown in the

output.

The no variant of this command disables the debug ip interface command.

Syntax debug ip packet interface {<interface-name>|all} [address

<ip-address>|verbose|hex|arp|udp|tcp|icmp]

no debug ip packet interface [<interface-name>]

Mode Privileged Exec and Global Configuration

Parameter Description

<interface> Specify a single Layer 3 interface name (not a range of interfaces)

This keyword can be specified as either all or as a single Layer 3

interface to show debugging for either all interfaces or a single

interface.

all Specify all Layer 3 interfaces on the device.

<ip-address> Specify an IPv4 address.

If this keyword is specified, then only packets with the specified IP

address as specified in the ip-address placeholder are shown in the

output.

verbose Specify verbose to output more of the IP packet.

If this keyword is specified then more of the packet is shown in the

output.

hex Specify hex to output the IP packet in hexadecimal.

If this keyword is specified, then the output for the packet is shown

in hex.

arp Specify arp to output ARP protocol packets.

If this keyword is specified, then ARP packets are shown in the

output.

udp Specify udp to output UDP protocol packets.

If this keyword is specified then UDP packets are shown in the

output.

tcp Specify tcp to output TCP protocol packets.

If this keyword is specified, then TCP packets are shown in the

output.

icmp Specify icmp to output ICMP protocol packets.

If this keyword is specified, then ICMP packets are shown in the

output.

613-50137-01 Rev A Command Reference for FS980M Series 578

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

DEBUG IP PACKET INTERFACE

Examples To turn on ARP packet debugging on vlan1, use the command:

awplus# debug ip packet interface vlan1 arp

To turn on all packet debugging on all interfaces on the device, use the command:

awplus# debug ip packet interface all

To turn on TCP packet debugging on vlan1 and IP address 192.168.2.4, use

the command:

awplus# debug ip packet interface vlan1 address 192.168.2.4 tcp

To turn off IP packet interface debugging on all interfaces, use the command:

awplus# no debug ip packet interface

To turn off IP packet interface debugging on interface vlan2, use the command:

awplus# no debug ip packet interface vlan2

Commands

no debug all

tcpdump

terminal monitor

undebug ip packet interface

613-50137-01 Rev A Command Reference for FS980M Series 579

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

IP ADDRESS (IP ADDRESSING AND PROTOCOL)

ip address (IP Addressing and Protocol)

Overview This command sets a static IP address on an interface.

The no variant of this command removes the IP address from the interface. You

cannot remove the primary address when a secondary address is present.

Syntax ip address <ip-addr/prefix-length> [secondary] [label <label>]

no ip address [<ip-addr/prefix-length>] [secondary]

Mode Interface Configuration for a VLAN interface or a local loopback interface.

Usage To set the primary IP address on the interface, specify only ip address

<ip-address/m>. This overwrites any configured primary IP address. To add

additional IP addresses on this interface, use the secondary parameter. You must

configure a primary address on the interface before configuring a secondary

address.

NOTE: Use show running-config interface not show ip interface brief when you

need to view a secondary address configured on an interface. show ip interface brief

will only show the primary address not a secondary address for an interface.

Examples To add the primary IP address 10.10.10.50/24 to the interface vlan3, use the

following commands:

awplus# configure terminal

awplus(config)# interface vlan3

awplus(config-if)# ip address 10.10.10.50/24

To add the secondary IP address 10.10.11.50/24 to the same interface, use the

following commands:

awplus# configure terminal

awplus(config)# interface vlan3

awplus(config-if)# ip address 10.10.11.50/24 secondary

Parameter Description

<ip-addr/prefix-

length>

The IPv4 address and prefix length you are assigning to the

interface.

secondary Secondary IP address.

label Adds a user-defined description of the secondary IP address.

<label> A user-defined description of the secondary IP address. Valid

characters are any printable character and spaces.

613-50137-01 Rev A Command Reference for FS980M Series 580

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

IP ADDRESS (IP ADDRESSING AND PROTOCOL)

To add the IP address 10.10.11.50/24 to the local loopback interface lo, use

the following commands:

awplus# configure terminal

awplus(config)# interface lo

awplus(config-if)# ip address 10.10.11.50/24

Commands

interface (to configure)

show ip interface

show running-config interface

613-50137-01 Rev A Command Reference for FS980M Series 581

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

IP GRATUITOUS-ARP-LINK

ip gratuitous-arp-link

Overview This command sets the Gratuitous ARP time limit for all switchports. The time limit

restricts the sending of Gratuitous ARP packets to one Gratuitous ARP packet

within the time in seconds.

NOTE: This command specifies time between sequences of Gratuitous ARP packets,

and time between individual Gratuitous ARP packets occurring in a sequence, to allow

legacy support for older devices and interoperation between other devices that are not

ready to receive and forward data until several seconds after linkup.

Additionally, jitter has been applied to the delay following linkup, so Gratuitous ARP

packets applicable to a given port are spread over a period of 1 second so are not all

sent at once. Remaining Gratuitous ARP packets in the sequence occur after a fixed

delay from the first one.

Syntax ip gratuitous-arp-link <0-300>

no ip gratuitous-arp-link

Default The default Gratuitous ARP time limit for all switchports is 8 seconds.

Mode Global Configuration

Usage Every switchport will send a sequence of 3 Gratuitous ARP packets to each VLAN

that the switchport is a member of, whenever the switchport moves to the

forwarding state. The first Gratuitous ARP packet is sent 1 second after the

switchport becomes a forwarding switchport. The second and third Gratuitous

ARP packets are each sent after the time period specified by the Gratuitous ARP

time limit.

Additionally, the Gratuitous ARP time limit specifies the minimum time between

the end of one Gratuitous ARP sequence and the start of another Gratuitous ARP

sequence. When a link is flapping, the switchport’s state is set to forwarding several

times. The Gratuitous ARP time limit is imposed to prevent Gratuitous ARP packets

from being sent undesirably often.

Examples To disable the sending of Gratuitous ARP packets, use the commands :

awplus# configure terminal

awplus(config)# ip gratuitous-arp-link 0

Parameter Description

<0-300>Specify the minimum time between sequences of Gratuitous ARPs and

the fixed time between Gratuitous ARPs occurring in a sequence, in

seconds.

0 disables the sending of Gratuitous ARP packets.

The default is 8 seconds.

613-50137-01 Rev A Command Reference for FS980M Series 582

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

IP GRATUITOUS-ARP-LINK

To restrict the sending of Gratuitous ARP packets to one every 20 seconds, use the

commands:

awplus# configure terminal

awplus(config)# ip gratuitous-arp-link 20

Validation

Commands

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 583

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

IP LIMITED-LOCAL-PROXY-ARP

ip limited-local-proxy-arp

Overview Use this command to enable local proxy ARP, but only for a specified set of IP

addresses. This makes the device respond to ARP requests for those IP addresses

when the addresses are reachable via the interface you are configuring.

To specify the IP addresses, use the command local-proxy-arp.

Use the no variant of this command to disable limited local proxy ARP. This stops

your device from intercepting and responding to ARP requests for the specified

hosts. This allows the hosts to use MAC address resolution to communicate directly

with one another.

Syntax ip limited-local-proxy-arp

no ip limited-local-proxy-arp

Default Limited local proxy ARP is disabled by default.

Mode Interface Configuration

Usage This command allows you to stop MAC address resolution for specified hosts.

Limited local proxy ARP works by intercepting ARP requests for the specified hosts

and responding with your device’s own MAC address details instead of the

destination host’s details. This stops hosts from learning the MAC address of the

other hosts through ARP requests.

Limited local proxy ARP ensures that the specified devices cannot send traffic that

bypasses Layer 3 routing on your device. This gives you control over which hosts

may communicate with one another.

Example To enable limited local proxy ARP, so that the device makes ARP responses to ARP

requests for specified addresses, when the ARP requests are received on VLAN2

and the addresses are routed out VLAN2, use the commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ip limited-local-proxy-arp

Commands

ip local-proxy-arp

local-proxy-arp

613-50137-01 Rev A Command Reference for FS980M Series 584

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

IP LOCAL-PROXY-ARP

ip local-proxy-arp

Overview This command allows you to stop MAC address resolution between hosts within a

private VLAN edge interface. Local Proxy ARP works by intercepting ARP requests

between hosts within a subnet and responding with your device’s own MAC

address details instead of the destination host’s details. This stops hosts from

learning the MAC address of other hosts within its subnet through ARP requests.

Local Proxy ARP ensures that devices within a subnet cannot send traffic that

bypasses Layer 3 routing on your device. This lets you monitor and filter traffic

between hosts in the same subnet, and enables you to have control over which

hosts may communicate with one another.

When Local Proxy ARP is operating on an interface, your device does not generate

or forward any ICMP-Redirect messages on that interface. This command does not

enable proxy ARP on the interface; see the ip proxy-arp command for more

information on enabling proxy ARP.

The no variant of this command disables Local Proxy ARP to stop your device from

intercepting and responding to ARP requests between hosts within a subnet. This

allows the hosts to use MAC address resolution to communicate directly with one

another. Local Proxy ARP is disabled by default.

Syntax ip local-proxy-arp

no ip local-proxy-arp

Default Local proxy ARP is disabled by default

Mode Interface Configuration for a VLAN interface or a local loopback interface.

Examples To enable your device to apply Local Proxy ARP on the interface vlan7, use the

following commands:

awplus# configure terminal

awplus(config)# interface vlan7

awplus(config-if)# ip local-proxy-arp

To disable your device to apply Local Proxy ARP on the interface vlan7, use the

following commands:

awplus# configure terminal

awplus(config)# interface vlan7

awplus(config-if)# no ip local-proxy-arp

Commands

ip proxy-arp

show arp

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 585

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

IP PROXY-ARP

ip proxy-arp

Overview This command enables Proxy ARP responses to ARP requests on an interface.

When enabled, your device intercepts ARP broadcast packets and substitutes its

own physical address for that of the remote host. By responding to the ARP

request, your device ensures that subsequent packets from the local host are

directed to its physical address, and it can then forward these to the remote host.

Your device responds only when it has a specific route to the address being

requested, excluding the interface route that the ARP request arrived from. It

ignores all other ARP requests. See the ip local-proxy-arp command about

enabling your device to respond to other ARP messages.

The no variant of this command disables Proxy ARP responses on an interface.

Proxy ARP is disabled by default.

Syntax ip proxy-arp

no ip proxy-arp

Default Proxy ARP is disabled by default.

Mode Interface Configuration for a VLAN interface or a local loopback interface.

Examples To enable your device to Proxy ARP on the interface vlan13, use the following

commands:

awplus# configure terminal

awplus(config)# interface vlan13

awplus(config-if)# ip proxy-arp

To disable your device to Proxy ARP on the interface vlan13, use the following

commands:

awplus# configure terminal

awplus(config)# interface vlan13

awplus(config-if)# no ip proxy-arp

Commands

arp (IP address MAC)

ip local-proxy-arp

show arp

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 586

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

LOCAL-PROXY-ARP

local-proxy-arp

Overview Use this command to specify an IP subnet for use with limited local proxy ARP.

When limited local proxy ARP is enabled with the command ip

limited-local-proxy-arp, the device will respond to ARP requests for addresses in

that subnet.

Use the no variant of this command to stop specifying a subnet for use with limited

local proxy ARP.

Syntax local-proxy-arp [<ip-add/mask>]

no local-proxy-arp [<ip-add/mask>]

Default No subnets are specified for use with limited local proxy ARP.

Mode Global Configuration

Example To specify limited local proxy ARP for the address 172.22.0.3, use the following

commands:

awplus# configure terminal

awplus(config)# local-proxy-arp 172.22.0.3/32

Commands

ip limited-local-proxy-arp

Parameter Description

<ip-add/mask> The IP subnet to use with limited local proxy ARP, in dotted

decimal format (A.B.C.D/M). To specify a single IP address, use a

32-bit mask.

613-50137-01 Rev A Command Reference for FS980M Series 587

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

IP UNREACHABLES

ip unreachables

Overview Use this command to enable ICMP (Internet Control Message Protocol) type 3,

destination unreachable, messages.

Use the no variant of this command to disable destination unreachable messages.

This prevents an attacker from using these messages to discover the topology of a

network.

Syntax ip unreachables

no ip unreachables

Default Destination unreachable messages are enabled by default.

Mode Global Configuration

Usage When a device receives a packet for a destination that is unreachable it returns an

ICMP type 3 message, this message includes a reason code, as per the table below.

An attacker can use these messages to obtain information regarding the topology

of a network. Disabling destination unreachable messages, using the no ip

unreachables command, secures your network against this type of probing.

NOTE: Disabling ICMP destination unreachable messages breaks applications such as

traceroute and Path MTU Discovery (PMTUD), which depend on these messages to

operate correctly.

Table 17-1: ICMP type 3 reason codes and description

Code Description [RFC]

0Network unreachable [RFC792]

1Host unreachable [RFC792]

2Protocol unreachable [RFC792]

3Port unreachable [RFC792]

4Fragmentation required, and DF flag set [RFC792]

5Source route failed [RFC792]

6Destination network unknown [RFC1122]

7Destination host unknown [RFC1122]

8Source host isolated [RFC1122]

9Network administratively prohibited [RFC768]

10 Host administratively prohibited [RFC869]

11 Network unreachable for Type of Service [RFC908]

12 Host unreachable for Type of Service [RFC938]

13 Communication administratively prohibited [RFC905]

613-50137-01 Rev A Command Reference for FS980M Series 588

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

IP UNREACHABLES

Example To disable destination unreachable messages, use the commands

awplus# configure terminal

awplus(config)# no ip unreachables

To enable destination unreachable messages, use the commands

awplus# configure terminal

awplus(config)# ip unreachables

14 Host Precedence Violation [RFC1812]

15 Precedence cutoff in effect [RFC1812]

Table 17-1: ICMP type 3 reason codes and description (cont.)

Code Description [RFC]

613-50137-01 Rev A Command Reference for FS980M Series 589

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

PING

ping

Overview This command sends a query to another IPv4 host (send Echo Request messages).

Syntax ping [ip] <host> [broadcast] [df-bit {yes|no}] [interval

<0-128>] [pattern <hex-data-pattern>] [repeat

{<1-2147483647>|continuous}] [size <36-18024>] [source

<ip-addr>] [timeout <1-65535>] [tos <0-255>]

Mode User Exec and Privileged Exec

Example To ping the IP address 10.10.0.5 use the following command:

awplus# ping 10.10.0.5

Parameter Description

<host>The destination IP address or hostname.

broadcast Allow pinging of a broadcast address.

df-bit Enable or disable the do-not-fragment bit in the IP header.

interval <0-128> Specify the time interval in seconds between sending ping

packets. The default is 1. You can use decimal places to

specify fractions of a second. For example, to ping every

millisecond, set the interval to 0.001.

pattern <hex-

data-pattern>

Specify the hex data pattern.

repeat Specify the number of ping packets to send.

<1-2147483647> Specify repeat count. The default is 5.

continuous Continuous ping

size <36-18024> The number of data bytes to send, excluding the 8 byte ICMP

header. The default is 56 (64 ICMP data bytes).

source <ip-addr> The IP address of a configured IP interface to use as the

source in the IP header of the ping packet.

timeout

<1-65535>

The time in seconds to wait for echo replies if the ARP entry is

present, before reporting that no reply was received. If no

ARP entry is present, it does not wait.

tos <0-255> The value of the type of service in the IP header.

613-50137-01 Rev A Command Reference for FS980M Series 590

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

SHOW ARP

show arp

Overview Use this command to display entries in the ARP routing and forwarding table—the

ARP cache contains mappings of IP addresses to physical addresses for hosts. To

have a dynamic entry in the ARP cache, a host must have used the ARP protocol to

access another host.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show arp [security [interface [<interface-list>]]

show arp [statistics [detail][interface [<interface-list>]]

Mode User Exec and Privileged Exec

Usage Running this command with no additional parameters will display all entries in the

ARP routing and forwarding table.

Example To display all ARP entries in the ARP cache, use the following command:

awplus# show arp

Output Figure 17-3: Example output from the show arp command

Parameter Description

security Specify the DHCP Snooping ARP security output option.

interface Specify an interface list for DHCP Snooping ARP security

output.

<interface-list>Specify a single Layer 3 interface name, or a range of

interfaces.

statistics Specify brief DHCP Snooping ARP security statistics.

detail Specify detailed DHCP Snooping ARP security statistics.

awplus#show arp



IP Address MAC Address Interface Port Type 

192.168.10.2 0015.77ad.fad8 vlan1 port1.0.1 dynamic

192.168.20.2 0015.77ad.fa48 vlan2 port1.0.2 dynamic

192.168.1.100 00d0.6b04.2a42 vlan2 port1.0.6 static

613-50137-01 Rev A Command Reference for FS980M Series 591

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

SHOW ARP

Commands

arp (IP address MAC)

clear arp-cache

Table 18: Parameters in the output of the show arp command

Parameter Meaning

IP Address IP address of the network device this entry maps to.

MAC Address Hardware address of the network device.

Interface Interface over which the network device is accessed.

Port Physical port that the network device is attached to.

Type Whether the entry is a static or dynamic entry. Static

entries are added using the arp (IP address MAC)

command. Dynamic entries are learned from ARP

request/reply message exchanges.

613-50137-01 Rev A Command Reference for FS980M Series 592

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

SHOW DEBUGGING IP PACKET

show debugging ip packet

Overview Use this command to show the IP interface debugging status. IP interface

debugging is set using the debug ip packet interface command.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show debugging ip packet

Mode User Exec and Privileged Exec

Example To display the IP interface debugging status when the terminal monitor off, use the

command:

awplus# terminal no monitor

awplus# show debug ip packet

Output Figure 17-4: Example output from the show debugging ip packet command

with terminal monitor off

Example To display the IP interface debugging status when the terminal monitor is on, use

the command:

awplus# terminal monitor

awplus# show debug ip packet

Output Figure 17-5: Example output from the show debugging ip packet command

with terminal monitor on

awplus#terminal no monitor



awplus#show debug ip packet



IP debugging status:



interface all tcp (stopped)



interface vlan1 arp verbose (stopped)

awplus#terminal monitor



awplus#show debug ip packet



IP debugging status:



interface all tcp (running)



interface vlan1 arp verbose (running)

613-50137-01 Rev A Command Reference for FS980M Series 593

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

SHOW DEBUGGING IP PACKET

Commands

debug ip packet interface

terminal monitor

613-50137-01 Rev A Command Reference for FS980M Series 594

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

SHOW IP INTERFACE

show ip interface

Overview Use this command to display information about interfaces and the IP addresses

assigned to them. To display information about a specific interface, specify the

interface name with the command.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ip interface [<interface-list>] [brief]

Mode User Exec and Privileged Exec

Examples To show brief information for the assigned IP address for interface port1.0.2 use

the command:

awplus# show ip interface port1.0.2 brief

To show the IP addresses assigned to vlan2 and vlan3, use the command:

awplus# show ip interface vlan2-3 brief

Output Figure 17-6: Example output from the show ip interface brief command

Parameter Description

<interface-list> The interfaces to display information about. An interface-list

can be:

•an interface, e.g. vlan2

• a continuous range of interfaces separated by a hyphen, e.g.

vlan2-8 or vlan2-vlan5

• a comma-separated list of interfaces or interface ranges, e.g.

vlan2,vlan5,vlan8-10

The specified interfaces must exist.

Interface IP-Address Status Protocol

port1.0.2 unassigned admin up down

vlan1 192.168.1.1 admin up running

vlan2 192.168.2.1 admin up running

vlan3 192.168.3.1 admin up running

vlan8 unassigned admin up down

613-50137-01 Rev A Command Reference for FS980M Series 595

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

SHOW IP SOCKETS

show ip sockets

Overview Use this command to display information about the IP or TCP sockets that are

present on the device. It includes TCP, UDP listen sockets, displaying associated IP

address and port.

The information displayed for established TCP sessions includes the remote IP

address, port, and session state. Raw IP protocol listen socket information is also

displayed for protocols such as ICMP6, which are configured to receive IP packets

with the associated protocol number.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ip sockets

Mode Privileged Exec

Usage Use this command to verify that the socket being used is opening correctly. If there

is a local and remote endpoint, a connection is established with the ports

indicated.

Note that this command does not display sockets that are used internally for

exchanging data between the various processes that exist on the device and are

involved in its operation and management. It only displays sockets that are present

for the purposes of communicating with other external devices.

Example To display IP sockets currently present on the device, use the command:

awplus# show ip sockets

Output Figure 17-7: Example output from the show ip sockets command



Socket information



Not showing 40 local connections

Not showing 7 local listening ports



Typ Local Address Remote Address State

tcp 0.0.0.0:111 0.0.0.0:* LISTEN

tcp 0.0.0.0:80 0.0.0.0:* LISTEN

tcp 0.0.0.0:23 0.0.0.0:* LISTEN

tcp 0.0.0.0:443 0.0.0.0:* LISTEN

tcp 0.0.0.0:4743 0.0.0.0:* LISTEN

tcp 0.0.0.0:873 0.0.0.0:* LISTEN

613-50137-01 Rev A Command Reference for FS980M Series 596

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

SHOW IP SOCKETS

tcp :::23 :::* LISTEN

udp 0.0.0.0:111 0.0.0.0:*

udp 226.94.1.1:5405 0.0.0.0:*

udp 0.0.0.0:161 0.0.0.0:*

udp :::161 :::*

raw 0.0.0.0:112 0.0.0.0:* 112

raw :::58 :::* 58

raw :::112 :::* 112

Table 19: Parameters in the output of the show ip sockets command

Parameter Description

Not showing

local

connections

This field refers to established sessions between processes internal

to the device, that are used in its operation and management.

These sessions are not displayed as they are not useful to the user.

<number> is some positive integer.

Not showing

local

listening

ports

This field refers to listening sockets belonging to processes internal

to the device, that are used in its operation and management. They

are not available to receive data from other devices. These sessions

are not displayed as they are not useful to the user. <number> is

some positive integer.

Typ This column displays the type of the socket. Possible values for this

column are:

tcp : IP Protocol 6

udp : IP Protocol 17

raw : Indicates that socket is for a non port-orientated protocol (i.e.

a protocol other than TCP or UDP) where all packets of a specified IP

protocol type are accepted. For raw socket entries the protocol type

is indicated in subsequent columns.

Local

Address

For TCP and UDP listening sockets this shows the destination IP

address and destination TCP or UDP port number for which the

socket will receive packets. The address and port are separated by ’:’.

If the socket will accept packets addressed to any of the device’s IP

addresses, the IP address will be 0.0.0.0 for IPv4 or :: for IPv6. For

active TCP sessions the IP address will display which of the devices

addresses the session was established with. For raw sockets this

displays the IP address and IP protocol for which the socket will

accept IP packets. The address and protocol are separated by ’:’. If

the socket will accept packets addressed to any of the device’s IP

addresses, the IP address will be 0.0.0.0 for IPv4 and :: for IPv6. IP

Protocol assignments are described

at:www.iana.org/assignments/protocol-numbers

613-50137-01 Rev A Command Reference for FS980M Series 597

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

SHOW IP SOCKETS

Remote

Address

For TCP and UDP listening sockets this shows the source IP address

(either IPv4 or IPv6) and source TCP or UDP port number for which

the socket will accept packets. The address and port are separated

by ’:’. If the socket will accept packets addressed from any IP

address, the IP address will be 0.0.0.0 for IPv4 . This is the usual case

for a listening socket. Normally for a listen socket any source port

will be accepted. This is indicated by “. For active TCP sessions the IP

address will display the remote address and port the session was

established with. For raw sockets the entry in this column will be

0.0.0.0: for IPv4 .

State This column shows the state of the socket. For TCP sockets this

shows the state of the TCP state machine. For UDP sockets this

column is blank. For raw sockets it contains the IP protocol number.

The possible TCP states are:

LISTEN

SYN-SENT

SYN-RECEIVED

ESTABLISHED

FIN-WAIT-1

FIN-WAIT-2

CLOSE-WAIT

CLOSING

LAST-ACK

TIME-WAIT

CLOSED

RFC793 contains the TCP state machine diagram with Section 3.2

describing each of the states.

Table 19: Parameters in the output of the show ip sockets command (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 598

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

SHOW IP TRAFFIC

show ip traffic

Overview Use this command to display statistics regarding IP traffic sent and received by all

interfaces on the device, showing totals for IP and IPv6 and then broken down into

sub-categories such as TCP, UDP, ICMP and their IPv6 equivalents when

appropriate.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ip traffic

Mode Privileged Exec

Example To display IP traffic statistics, use the command:

awplus# show ip traffic

Output Figure 17-8: Example output from the show ip traffic command



IP:

261998 packets received

261998 delivered

261998 sent

69721 multicast packets received

69721 multicast packets sent

23202841 bytes received

23202841 bytes sent

7669296 multicast bytes received

7669296 multicast bytes sent

IPv6:

28 packets discarded on transmit due to no route

ICMP6:

UDP6:

UDPLite6:

TCP:

0 remote connections established

40 local connections established

7 remote listening ports

7 local listening ports

261 active connection openings

247 passive connection openings

14 connection attempts failed

122535 segments received

122535 segments transmitted

14 resets transmitted

227 TCP sockets finished time wait in fast timer

613-50137-01 Rev A Command Reference for FS980M Series 599

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

SHOW IP TRAFFIC

155 delayed acks sent

21187 headers predicted

736 pure ACKs

80497 pure ACKs predicted

UDP:

139468 datagrams received

139468 datagrams sent

UDPLite:

Table 20: Parameters in the output of the show ip traffic command

Parameter Description

IPv4 IPv4 counters

IPv6 IPv6 counters

received packets with no route Received packets with no route

truncated packets received Truncated packets received

multicast packets received Multicast packets received

multicast packets sent Multicast packets sent

broadcast packets received Broadcast packets received

broadcast packets sent Broadcast packets sent

bytes received Bytes received

bytes sent Bytes sent

multicast bytes received Multicast bytes received

multicast bytes sent Multicast bytes sent

broadcast bytes received Broadcast bytes received

broadcast bytes sent Broadcast bytes sent

packets received Packets received

packets received with invalid

headers

Packets received with invalid headers

oversize packets received Oversize packets received

packets received with no route Packets received with no route

packets received with invalid

address

Packets received with invalid address

packets received with unknown

protocol

Packets received with unknown protocol

truncated packets received Truncated packets received

received packets discarded Received packets discarded

received packets delivered Received packets delivered

forwarded packets transmitted Forwarded packets transmitted

613-50137-01 Rev A Command Reference for FS980M Series 600

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

SHOW IP TRAFFIC

packets transmitted Packets transmitted

packets discarded on transmit Packets discarded on transmit

packets discarded on transmit

due to no route

Packets discarded on transmit due to no

route

fragment reassembly timeouts Fragment reassembly timeouts

fragment reassembly required Fragment reassembly required

fragment reassembly OK Fragment reassembly OK

fragment reassembly failures Fragment reassembly failures

fragmentations succeeded Fragmentations succeeded

fragmentations failed Fragmentations failed

fragments created Fragments created

ICMP6 ICMPv6 counters

messages received Messages received

errors received Errors received

messages sent Messages sent

TCP TCP counters

remote connections

established

Remote connections established

local connections established Local connections established

remote listening ports Remote listening ports

local listening ports Local listening ports

active connection openings Active connection openings

passive connection openings Passive connection openings

connection attempts failed Connection attempts failed

connection resets received Connection resets received

segments received Segments received

segments transmitted Segments transmitted

retransmits Retransmits

bad segments received Bad segments received

resets transmitted Resets transmitted

datagrams received Datagrams received

received for unknown port Received for unknown port

datagrams sent Datagrams sent

syncookies sent Syncookies sent

Table 20: Parameters in the output of the show ip traffic command (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 601

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

SHOW IP TRAFFIC

syncookies received Syncookies received

syncookies failed Syncookies failed

embryonic resets Embryonic resets

sockets pruned Sockets pruned

ICMPs out of window ICMPs out of window

ICMPs dropped due to lock ICMPs dropped due to lock

ARPs filtered ARPs filtered

TCP sockets finished time wait

in fast timer

TCP sockets finished time wait in fast

timer

time wait sockets recycled by

time stamp

Time wait sockets recycled by time stamp

time wait sockets killed Time wait sockets killed

delayed acks sent Delayed acks sent delayed acks further

delayed because of locked socket

delayed acks lost Delayed acks lost

listening socket overflows Listening socket overflows

listening socket drops Listening socket drops

headers predicted Headers predicted

pure ACKs Pure ACKs

pure ACKs predicted Pure ACKs predicted

losses recovered by TCP Reno Losses recovered by TCP Reno

losses recovered by SACK Losses recovered by SACK

SACKs renegged SACKs renegged

detected reordering by FACK Detected reordering by FACK

detected reordering by SACK Detected reordering by SACK

detected reordering by TCP

Reno

Detected reordering by TCP Reno

detected reordering by

sequence

Detected reordering by sequence

full undos Full undos

partial undos Partial undos

SACK undos SACK undos

loss undos Loss undos

segments lost Segments lost

lost retransmits Lost retransmits

Table 20: Parameters in the output of the show ip traffic command (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 602

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

SHOW IP TRAFFIC

TCP Reno failures TCP Reno failures

SACK failures SACK failures

loss failures Loss failures

fast retransmits Fast retransmits

forward retransmits Forward retransmits

retransmits in slow start Retransmits in slow start

timeouts Timeouts

TCP Reno recovery failures TCP Reno recovery failures

SACK recovery failures SACK recovery failures

collapsed segments received Collapsed segments received

DSACKs sent for old packets DSACKs sent for old packets

DSACKs sent for out of order

segments

DSACKs sent for out of order segments

DSACKs received DSACKs received

DSACKs received for out of

order segments

DSACKs received for out of order

segments

connections reset due to

unexpected SYN

Connections reset due to unexpected SYN

connections reset due to

unexpected data

Connections reset due to unexpected

data

connections reset due to early

user close

Connections reset due to early user close

connections aborted due to

lack of memory

Connections aborted due to lack of

memory

connections aborted due to

timeout

Connections aborted due to timeout

connections aborted due to

lingering

Connections aborted due to lingering

connection aborts due to

connection failure

Connection aborts due to connection

failure

TCP memory pressure events TCP memory pressure events

SACKs discarded SACKs discarded

Old DSACKs ignored Old DSACKs ignored

DSACKs ignored without undo DSACKs ignored without undo

Spurious RTOs Spurious RTOs

TCP MD5 Not Found TCP MD5 Not Found

Table 20: Parameters in the output of the show ip traffic command (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 603

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

SHOW IP TRAFFIC

TCP MD5 Unexpected TCP MD5 Unexpected

TCP SACKs shifted TCP SACKs shifted

TCP SACKs merged TCP SACKs merged

TCP SACK shift fallback TCP SACK shift fallback

UDP UDP Counters

UDPLite UDPLite Counters

UDP6 UDPv6 Counters

UDPLite6 UDPLitev6 Counters

datagrams received Datagrams received

datagrams received for unknown

port

Datagrams received for unknown port

datagram receive errors Datagram receive errors

datagrams transmitted Datagrams transmitted

datagrams received Datagrams received

datagrams received for unknown

port

Datagrams received for unknown port

datagram receive errors Datagram receive errors

datagrams transmitted Datagrams transmitted

Table 20: Parameters in the output of the show ip traffic command (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 604

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

TCPDUMP

tcpdump

Overview Use this command to start a tcpdump, which gives the same output as the

Unix-like tcpdump command to display TCP/IP traffic. Press <ctrl> + c to stop

a running tcpdump.

Syntax tcpdump <line>

Mode Privileged Exec

Example To start a tcpdump running to capture IP packets, enter the command:

awplus# tcpdump ip

Output Figure 17-9: Example output from the tcpdump command

Commands

debug ip packet interface

Parameter Description

<line>Specify the dump options. For more information on the

options for this placeholder see

http://www.tcpdump.org/tcpdump_man.html

03:40:33.221337 IP 192.168.1.1 > 224.0.0.13: PIMv2, Hello, 

length: 34

1 packets captured

2 packets received by filter

0 packets dropped by kernel

613-50137-01 Rev A Command Reference for FS980M Series 605

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

TRACEROUTE

traceroute

Overview Use this command to trace the route to the specified IPv4 host.

Syntax traceroute {<ip-addr>|<hostname>}

Mode User Exec and Privileged Exec

Example awplus# traceroute 10.10.0.5

Parameter Description

<ip-addr> The destination IPv4 address. The IPv4 address uses the

format A.B.C.D.

<hostname>The destination hostname.

613-50137-01 Rev A Command Reference for FS980M Series 606

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IP ADDRESSING AND PROTOCOL COMMANDS

UNDEBUG IP PACKET INTERFACE

undebug ip packet interface

Overview This command applies the functionality of the no debug ip packet interface

command.

613-50137-01 Rev A Command Reference for FS980M Series 607

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Domain Name

Service (DNS)

Commands

Introduction

Overview This chapter provides an alphabetical reference of commands used to configure

the Domain Name Service (DNS) client.

For more information, see the IP Feature Overview and Configuration Guide.

Command List •“ip domain-list” on page 608

•“ip domain-lookup” on page 609

•“ip domain-name” on page 610

•“ip name-server” on page 611

•“show hosts” on page 613

•“show ip domain-list” on page 614

•“show ip domain-name” on page 615

•“show ip name-server” on page 616

613-50137-01 Rev A Command Reference for FS980M Series 608

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

DOMAIN NAME SERVICE (DNS) COMMANDS

IP DOMAIN-LIST

ip domain-list

Overview This command adds a domain to the DNS list. Domains are appended to

incomplete host names in DNS requests. Each domain in this list is tried in turn in

DNS lookups. This list is ordered so that the first entry you create is checked first.

The no variant of this command deletes a domain from the list.

Syntax ip domain-list <domain-name>

no ip domain-list <domain-name>

Mode Global Configuration

Usage If there are no domains in the DNS list, then your device uses the domain specified

with the ip domain-name command. If any domain exists in the DNS list, then the

device does not use the domain set using the ip domain-name command.

Example To add the domain example.net to the DNS list, use the following commands:

awplus# configure terminal

awplus(config)# ip domain-list example.net

Commands

ip domain-lookup

ip domain-name

show ip domain-list

Parameter Description

<domain-name> Domain string, for example “company.com”.

613-50137-01 Rev A Command Reference for FS980M Series 609

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

DOMAIN NAME SERVICE (DNS) COMMANDS

IP DOMAIN-LOOKUP

ip domain-lookup

Overview This command enables the DNS client on your device. This allows you to use

domain names instead of IP addresses in commands. The DNS client resolves the

domain name into an IP address by sending a DNS inquiry to a DNS server,

specified with the ip name-server command.

The no variant of this command disables the DNS client. The client will not attempt

to resolve domain names. You must use IP addresses to specify hosts in

commands.

Syntax ip domain-lookup

no ip domain-lookup

Mode Global Configuration

Usage The client is enabled by default. However, it does not attempt DNS inquiries unless

there is a DNS server configured.

For more information about DNS clients, see the IP Feature Overview and

Configuration Guide.

Examples To enable the DNS client on your device, use the following commands:

awplus# configure terminal

awplus(config)# ip domain-lookup

To disable the DNS client on your device, use the following commands:

awplus# configure terminal

awplus(config)# no ip domain-lookup

Commands

ip domain-list

ip domain-name

ip name-server

show hosts

show ip name-server

613-50137-01 Rev A Command Reference for FS980M Series 610

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

DOMAIN NAME SERVICE (DNS) COMMANDS

IP DOMAIN-NAME

ip domain-name

Overview This command sets a default domain for the DNS. The DNS client appends this

domain to incomplete host-names in DNS requests.

The no variant of this command removes the domain-name previously set by this

command.

Syntax ip domain-name <domain-name>

no ip domain-name <domain-name>

Mode Global Configuration

Usage If there are no domains in the DNS list (created using the ip domain-list command)

then your device uses the domain specified with this command. If any domain

exists in the DNS list, then the device does not use the domain configured with this

command.

When your device is using its DHCP client for an interface, it can receive Option 15

from the DHCP server. This option replaces the domain name set with this

command.

Example To configure the domain name, enter the following commands:

awplus# configure terminal

awplus(config)# ip domain-name company.com

Commands

ip domain-list

show ip domain-list

show ip domain-name

Parameter Description

<domain-name> Domain string, for example “company.com”.

613-50137-01 Rev A Command Reference for FS980M Series 611

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

DOMAIN NAME SERVICE (DNS) COMMANDS

IP NAME-SERVER

ip name-server

Overview This command adds IPv4 or IPv6 DNS server addresses. The DNS client on your

device sends DNS queries to IP addresses in this list when trying to resolve a host

name. Host names cannot be resolved until you have added at least one server to

this list. A maximum of three name servers can be added to this list.

The no variant of this command removes the specified DNS name-server address.

Syntax ip name-server <ip-addr>

no ip name-server <ip-addr>

Mode Global Configuration

Usage To allow the device to operate as a DNS proxy, your device must have learned

about a DNS name-server to forward requests to. Name-servers can be learned

through the following means:

• Manual configuration, using the ip name-server command

• Learned from DHCP server with Option 6

• Learned over a PPP tunnel if the neighbor advertises the DNS server

This command is used to statically configure a DNS name-server for the device to

use.

For more information about DHCP and DNS, see the IP Feature Overview and

Configuration Guide.

Examples To allow a device to send DNS queries to a DNS server with the IPv4 address

10.10.10.5, use the commands:

awplus# configure terminal

awplus(config)# ip name-server 10.10.10.5

To enable your device to send DNS queries to a DNS server with the IPv6 address

2001:0db8:010d::1, use the commands:

awplus# configure terminal

awplus(config)# ip name-server 2001:0db8:010d::1

Parameter Description

<ip-addr> The IP address of the DNS server that is being added to the name

server list. The address is entered in the form A.B.C.D for an IPv4

address, or in the form X:X::X:X for an IPv6 address.

613-50137-01 Rev A Command Reference for FS980M Series 612

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

DOMAIN NAME SERVICE (DNS) COMMANDS

IP NAME-SERVER

Commands

ip domain-list

ip domain-lookup

ip domain-name

show ip name-server

613-50137-01 Rev A Command Reference for FS980M Series 613

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

DOMAIN NAME SERVICE (DNS) COMMANDS

SHOW HOSTS

show hosts

Overview This command shows the default domain, domain list, and name servers

configured on your device.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show hosts

Mode User Exec and Privileged Exec

Example To display the default domain, use the command:

awplus# show hosts

Output Figure 18-1: Example output from the show hosts command

Commands

ip domain-list

ip domain-lookup

ip domain-name

ip name-server

awplus#show hosts



Default domain is mycompany.com

Domain list: company.com

Name/address lookup uses domain service

Name servers are 10.10.0.2 10.10.0.88

613-50137-01 Rev A Command Reference for FS980M Series 614

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

DOMAIN NAME SERVICE (DNS) COMMANDS

SHOW IP DOMAIN-LIST

show ip domain-list

Overview This command shows the domains configured in the domain list. The DNS client

uses the domains in this list to append incomplete hostnames when sending a

DNS inquiry to a DNS server.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ip domain-list

Mode User Exec and Privileged Exec

Example To display the list of domains in the domain list, use the command:

awplus# show ip domain-list

Output Figure 18-2: Example output from the show ip domain-list command

Commands

ip domain-list

ip domain-lookup

awplus#show ip domain-list

alliedtelesis.com

mycompany.com

613-50137-01 Rev A Command Reference for FS980M Series 615

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

DOMAIN NAME SERVICE (DNS) COMMANDS

SHOW IP DOMAIN-NAME

show ip domain-name

Overview This command shows the default domain configured on your device. When there

are no entries in the DNS list, the DNS client appends this domain to incomplete

hostnames when sending a DNS inquiry to a DNS server.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ip domain-name

Mode User Exec and Privileged Exec

Example To display the default domain configured on your device, use the command:

awplus# show ip domain-name

Output Figure 18-3: Example output from the show ip domain-name command

Commands

ip domain-name

ip domain-lookup

awplus#show ip domain-name

alliedtelesis.com

613-50137-01 Rev A Command Reference for FS980M Series 616

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

DOMAIN NAME SERVICE (DNS) COMMANDS

SHOW IP NAME-SERVER

show ip name-server

Overview This command displays a list of IPv4 and IPv6 DNS server addresses that your

device will send DNS requests to. This is a static list configured using the ip

name-server command.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ip name-server

Mode User Exec and Privileged Exec

Example To display the list of DNS servers that your device sends DNS requests to, use the

command:

awplus# show ip name-server

Output Figure 18-4: Example output from the show ip name-server command

Commands

ip domain-lookup

ip name-server

awplus# show ip name-server

10.10.0.123

10.10.0.124

2001:0db8:010d::1

613-50137-01 Rev A Command Reference for FS980M Series 617

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPv6 Commands

Introduction

Overview This chapter provides an alphabetical reference of commands used to configure

IPv6. For more information, see the IPv6 Feature Overview and Configuration

Guide.

Command List •“clear ipv6 neighbors” on page 618

•“ipv6 address” on page 619

•“ipv6 enable” on page 620

•“ipv6 nd raguard” on page 621

•“ipv6 neighbor” on page 623

•“ipv6 route” on page 624

•“ipv6 unreachables” on page 625

•“ping ipv6” on page 626

•“show ipv6 interface brief” on page 627

•“show ipv6 neighbors” on page 628

•“show ipv6 route” on page 629

•“show ipv6 route summary” on page 631

•“traceroute ipv6” on page 632

613-50137-01 Rev A Command Reference for FS980M Series 618

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 COMMANDS

CLEAR IPV6 NEIGHBORS

clear ipv6 neighbors

Overview Use this command to clear all dynamic IPv6 neighbor entries.

Syntax clear ipv6 neighbors

Mode Privileged Exec

Example awplus# clear ipv6 neighbors

613-50137-01 Rev A Command Reference for FS980M Series 619

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 COMMANDS

IPV6 ADDRESS

ipv6 address

Overview Use this command to set the IPv6 address of a VLAN interface and enable IPv6.

Use the no variant of this command to remove the IPv6 address assigned and

disable IPv6. Note that if no global addresses are left after removing the IPv6

address then IPv6 is disabled.

Syntax ipv6 address <ipv6-addr/prefix-length> [eui64]

no ipv6 address <ipv6-addr/prefix-length>

Mode Interface Configuration for a VLAN interface.

Examples To assign the IPv6 address 2001:0db8::a2/64 to the VLAN interface vlan2, use the

following commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ipv6 address 2001:0db8::a2/64

To remove the IPv6 address 2001:0db8::a2/64 from the VLAN interface vlan2, use

the following commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# no ipv6 address 2001:0db8::a2/64

Commands

show running-config

show ipv6 interface brief

show ipv6 route

Parameter Description

<ipv6-addr/prefix-

length>

Specifies the IPv6 address to be set. The IPv6

address uses the format X:X::X:X/Prefix-Length. The

prefix-length is usually set between 0 and 64.

613-50137-01 Rev A Command Reference for FS980M Series 620

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 COMMANDS

IPV6 ENABLE

ipv6 enable

Overview Use this command to enable IPv6 on an interface without an IPv6 global address

for the interface. This enables IPv6 with a IPv6 link-local address, not an IPv6 global

address.

Use the no variant of this command to disable IPv6 on an interface without a global

address. Note the no variant of this command does not operate on an interface

with an IPv6 global address or an interface configured for IPv6 stateless address

autoconfiguration (SLAAC).

Syntax ipv6 enable

no ipv6 enable

Mode Interface Configuration for a VLAN interface.

Usage The ipv6 enable command automatically configures an IPv6 link-local address on

the interface and enables the interface for IPv6 processing.

A link-local address is an IP (Internet Protocol) address that is only used for

communications in the local network, or for a point-to-point connection. Routing

does not forward packets with link-local addresses. IPv6 requires that a link-local

address is assigned to each interface that has the IPv6 protocol enabled, and when

addresses are assigned to interfaces for routing IPv6 packets.

Note that link-local addresses are retained in the system until they are negated by

using the no variant of the command that established them.

Also note that the link-local address is retained in the system if the global address

is removed using another command that was not used to establish the link-local

address. For example, if a link local address is established with the ipv6 enable

command then it will not be removed using a no ipv6 address command.

Examples To enable IPv6 with only a link-local IPv6 address on the VLAN interface vlan2,

use the following commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ipv6 enable

To disable IPv6 with only a link-local IPv6 address on the VLAN interface vlan2,

use the following commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# no ipv6 enable

Commands

ipv6 address

show ipv6 interface brief

show ipv6 route

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 621

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 COMMANDS

IPV6 ND RAGUARD

ipv6 nd raguard

Overview Use this command to apply the Router Advertisements (RA) Guard feature from the

Interface Configuration mode for a device port. This blocks all RA messages

received on a device port.

For more information about RA Guard, see the IPv6 Feature Overview and

Configuration Guide.

Use the no parameter with this command to disable RA Guard for a specified

device port.

Syntax ipv6 nd raguard

no ipv6 nd raguard

Default RA Guard is not enabled by default.

Mode Interface Configuration for a device port interface.

Usage Router Advertisements (RAs) are used by Routers to announce themselves on the

link. Applying RA Guard to a device port disallows Router Advertisements and

redirect messages. RA Guard blocks RAs from untrusted hosts. Blocking RAs stops

untrusted hosts from flooding malicious RAs and stops any misconfigured hosts

from disrupting traffic on the local network.

Enabling RA Guard on a port blocks RAs from a connected host and indicates the

port and host are untrusted. Disabling RA Guard on a port allows RAs from a

connected host and indicates the port and host are trusted. Ports and hosts are

trusted by default to allow RAs.

Example To enable RA Guard on device ports port1.0.2-1.0.12, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2-1.0.12

awplus(config-if)# ipv6 nd raguard

To verify RA Guard is enabled on device port interface port1.0.2, use the

command:

awplus# show running-config interface port1.0.2

To disable RA Guard on device ports port1.0.2-1.0.12, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2-port1.0.12

awplus(config-if)# no ipv6 nd raguard

When RA Guard is disabled on a device port it is not displayed in show

running-config output.

613-50137-01 Rev A Command Reference for FS980M Series 622

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 COMMANDS

IPV6 ND RAGUARD

Output Example output from using show running-config interface port1.0.2 to verify RA

Guard:

Commands

show running-config interface

!

interface port1.0.2

switchport mode access



ipv6 nd raguard

!

613-50137-01 Rev A Command Reference for FS980M Series 623

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 COMMANDS

IPV6 NEIGHBOR

ipv6 neighbor

Overview Use this command to add a static IPv6 neighbor entry.

Use the no variant of this command to remove a specific IPv6 neighbor entry.

Syntax ipv6 neighbor <ipv6-address> <vlan-name> <mac-address>

<port-list>

no ipv6 neighbor <ipv6-address> <vlan-name> <port-list>

Mode Global Configuration

Usage Use this command to clear a specific IPv6 neighbor entry. To clear all dynamic

address entries, use the clear ipv6 neighbors command.

Example To create a static neighbor entry for IPv6 address 2001:0db8::a2, on vlan 4, MAC

address 0000.cd28.0880, on port1.0.6, use the command:

awplus# configure terminal

awplus(config)# ipv6 neighbor 2001:0db8::a2 vlan4

0000.cd28.0880 port1.0.6

Commands

clear ipv6 neighbors

Parameter Description

<ipv6-address>Specify the neighbor’s IPv6 address in the format X:X::X:X.

<vlan-name>Specify the neighbor’s VLAN name.

<mac-address>Specify the MAC hardware address in hexadecimal notation in

the format HHHH.HHHH.HHHH.

<port-list> Specify the port number, or port range.

613-50137-01 Rev A Command Reference for FS980M Series 624

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 COMMANDS

IPV6 ROUTE

ipv6 route

Overview This command adds a static IPv6 route to the Routing Information Base (RIB). If this

route is the best route for the destination, then your device adds it to the

Forwarding Information Base (FIB). Your device uses the FIB to advertise routes to

neighbors and forward packets.

The no variant of this command removes the static route.

Syntax ipv6 route <dest-prefix> <dest-prefix/length>

{<gateway-ip>|<gateway-name>} [<distvalue>]

no ipv6 route <dest-prefix> <dest-prefix/length>

{<gateway-ip>|<gateway-name>} [<distvalue>]

Mode Global Configuration

Usage Administrative distance can be modified so static routes do not take priority over

other routes.

Example awplus# configure terminal

awplus(config)# ipv6 route 2001:0db8::1/128 vlan2 32

Validation

Commands

show running-config

show ipv6 route

Parameter Description

<dest-prefix/

length>

Specifies the IP destination prefix.

The IPv6 address prefix uses the format X:X::/prefix-length.

The prefix-length is usually set between 0 and 64.

<gateway-ip>Specifies the IP gateway (or next hop) address. The IPv6

address uses the format X:X::X:X/Prefix-Length. The

prefix-length is usually set between 0 and 64.

<gateway-name>Specifies the name of the gateway (or next hop) interface.

<distvalue>Specifies the administrative distance for the route. Valid

values are from 1 to 255.

613-50137-01 Rev A Command Reference for FS980M Series 625

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 COMMANDS

IPV6 UNREACHABLES

ipv6 unreachables

Overview Use this command to enable ICMPv6 (Internet Control Message Protocol version 6)

type 1, destination unreachable, messages.

Use the no variant of this command to disable destination unreachable messages.

This prevents an attacker from using these messages to discover the topology of a

network.

Syntax ipv6 unreachables

no ipv6 unreachables

Default Destination unreachable messages are enabled by default.

Mode Global Configuration

Usage When a device receives a packet for a destination that is unreachable it returns an

ICMPv6 type 1 message. This message includes a reason code, as per the table

below. An attacker can use these messages to obtain information regarding the

topology of a network. Disabling destination unreachable messages, using the no

ipv6 unreachables command, secures your network against this type of probing.

NOTE: Disabling ICMPv6 destination unreachable messages breaks applications such

as traceroute, which depend on these messages to operate correctly.

Example To disable destination unreachable messages, use the commands

awplus# configure terminal

awplus(config)# no ipv6 unreachables

To enable destination unreachable messages, use the commands

awplus# configure terminal

awplus(config)# ipv6 unreachables

Table 19-1: ICMPv6 type 1 reason codes and description

Code Description [RFC]

0No route to destination [RFC4443]

1Communication with destination administratively prohibited [RFC4443]

2Beyond scope of source address [RFC4443]

3Address unreachable [RF4443]

4Port unreachable [RFC4443]

5Source address failed ingress/egress policy [RFC4443]

6Reject route to destination [RFC4443

7Error in Source Routing Header [RFC6554]

613-50137-01 Rev A Command Reference for FS980M Series 626

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 COMMANDS

PING IPV6

ping ipv6

Overview This command sends a query to another IPv6 host (send Echo Request messages).

NOTE: Use of the interface parameter keyword, plus an interface or an interface range,

with this command is only valid when pinging an IPv6 link local address.

Syntax ping ipv6 {<host>|<ipv6-address>} [repeat

{<1-2147483647>|continuous}] [size <10-1452>] [interface

<interface-list>] [timeout <1-65535>]

Mode User Exec and Privileged Exec

Example awplus# ping ipv6 2001:0db8::a2

Commands

traceroute ipv6

Parameter Description

<ipv6-addr> The destination IPv6 address. The IPv6 address uses the

format X:X::X:X.

<hostname>The destination hostname.

repeat Specify the number of ping packets to send.

<1-2147483647> Specify repeat count. The default is 5.

size <10-1452> The number of data bytes to send, excluding the 8 byte ICMP

header. The default is 56 (64 ICMP data bytes).

interface

<interface-list>

The interface or range of configured IP interfaces to use as the

source in the IP header of the ping packet.

timeout

<1-65535>

The time in seconds to wait for echo replies if the ARP entry is

present, before reporting that no reply was received. If no ARP

entry is present, it does not wait.

repeat Specify the number of ping packets to send.

<1-2147483647> Specify repeat count. The default is 5.

continuous Continuous ping.

size <10-1452> The number of data bytes to send, excluding the 8 byte ICMP

header. The default is 56 (64 ICMP data bytes).

timeout

<1-65535>

The time in seconds to wait for echo replies if the ARP entry is

present, before reporting that no reply was received. If no ARP

entry is present, it does not wait.

613-50137-01 Rev A Command Reference for FS980M Series 627

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 COMMANDS

SHOW IPV6 INTERFACE BRIEF

show ipv6 interface brief

Overview Use this command to display brief information about interfaces and the IPv6

address assigned to them.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ipv6 interface [brief]

Mode User Exec and Privileged Exec

Examples awplus# show ipv6 interface brief

Output Figure 19-1: Example output from the show ipv6 interface brief command

Commands

show interface brief

Parameter Description

brief Specify this optional parameter to display brief IPv6 interface

information.

awplus#show ipv6 interface brief

Interface IPv6-Address Status Protocol

lo unassigned admin up running

vlan1 2001:db8::1/48 admin up down

fe80::215:77ff:fee9:5c50/64

613-50137-01 Rev A Command Reference for FS980M Series 628

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 COMMANDS

SHOW IPV6 NEIGHBORS

show ipv6 neighbors

Overview Use this command to display all IPv6 neighbors.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ipv6 neighbors

Mode User Exec and Privileged Exec

613-50137-01 Rev A Command Reference for FS980M Series 629

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 COMMANDS

SHOW IPV6 ROUTE

show ipv6 route

Overview Use this command to display the IPv6 routing table for a protocol or from a

particular table.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ipv6 route

[connected|database|summary|<ipv6-address>|<ipv6-addr/prefix-l

ength>)]

Mode User Exec and Privileged Exec

Example 1 To display an IP route with all parameters turned on, use the following command:

awplus# show ipv6 route

Output Figure 19-2: Example output of the show ipv6 route command

Parameter Description

connected Displays only the routes learned from connected

interfaces.

database Displays only the IPv6 routing information extracted

from the database.

summary Displays summary information from the IPv6 routing

table.

<ipv6-address> Displays the routes for the specified address in the IP

routing table. The IPv6 address uses the format

X:X::X:X/Prefix-Length. The prefix-length is usually set

between 0 and 64.

<ipv6-prefix/length> Displays only the routes for the specified IP prefix.



IPv6 Routing Table

Codes: C - connectedS ::/0 [1/0] via 2001::a:0:0:c0a8:a6, vlan10

C 2001:db8::a:0:0:0:0/64 via ::, vlan10

C 2001:db8::14:0:0:0:0/64 via ::, vlan20

C 2001:db8::0:0:0:0/64 via ::, vlan30

C 2001:db8::28:0:0:0:0/64 via ::, vlan40

C 2001:db8::fa:0:0:0:0/64 via ::, vlan250

C 2001:db8::/64 via ::, vlan250

C 2001:db8::/64 via ::, vlan40

C 2001:db8::/64 via ::, vlan20

C 2001:db8::/64 via ::, vlan10

613-50137-01 Rev A Command Reference for FS980M Series 630

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 COMMANDS

SHOW IPV6 ROUTE

Example 2 To display all database entries for an IP route, use the following command:

awplus# show ipv6 route database

Output Figure 19-3: Example output of the show ipv6 route database command



IPv6 Routing Table

Codes: C - connected> - selected route, * - FIB route, p - stale

info

Timers: Uptime



S ::/0 [1/0] via 2001::a:0:0:c0a8:a01 inactive, 6d22h12m

[1/0] via 2001::fa:0:0:c0a8:fa01 inactive, 6d22h12m

613-50137-01 Rev A Command Reference for FS980M Series 631

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 COMMANDS

SHOW IPV6 ROUTE SUMMARY

show ipv6 route summary

Overview Use this command to display the summary of the current NSM RIB entries.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ipv6 route summary

Mode User Exec and Privileged Exec

Example To display IP route summary, use the following command:

awplus# show ipv6 route summary

Output Figure 19-4: Example output from the show ipv6 route summary command

Commands

show ip route database

IPv6 routing table name is Default-IPv6-Routing-Table(0)

IPv6 routing table maximum-paths is 4

RouteSource Networks

connected 4

Total 4

FIB 0

613-50137-01 Rev A Command Reference for FS980M Series 632

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 COMMANDS

TRACEROUTE IPV6

traceroute ipv6

Overview Use this command to trace the route to the specified IPv6 host.

Syntax traceroute ipv6 {<ipv6-addr>|<hostname>}

Mode User Exec and Privileged Exec

Example To run a traceroute for the IPv6 address 2001:0db8::a2, use the following

command:

awplus# traceroute ipv6 2001:0db8::a2

Commands

ping ipv6

Parameter Description

<ipv6-addr> The destination IPv6 address. The IPv6 address uses the format

X:X::X:X.

<hostname>The destination hostname.

613-50137-01 Rev A Command Reference for FS980M Series 633

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Routing Commands

Introduction

Overview This chapter provides an alphabetical reference of routing commands that are

common across the routing IP protocols. For more information, see the Route

Selection Feature Overview and Configuration Guide.

Command List •“ip route” on page 634

•“ipv6 route” on page 636

•“maximum-paths” on page 637

•“show ip route” on page 638

•“show ip route database” on page 640

•“show ip route summary” on page 641

•“show ipv6 route” on page 642

•“show ipv6 route summary” on page 644

613-50137-01 Rev A Command Reference for FS980M Series 634

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

ROUTING COMMANDS

IP ROUTE

ip route

Overview This command adds a static route to the Routing Information Base (RIB). If this

route is the best route for the destination, then your device adds it to the

Forwarding Information Base (FIB). Your device uses the FIB to advertise routes to

neighbors and forward packets.

The no variant of this command removes the static route from the RIB and FIB.

Syntax ip route <subnet&mask> {<gateway-ip>|<interface>} [<distance>]

no ip route <subnet&mask> {<gateway-ip>|<interface>}

[<distance>]

Mode Global Configuration

Default The default administrative distance for a static route is 1 for priority over non-static

routes.

Usage Administrative distance can be modified so that static routes do not take priority

over other routes.

Specify a ‘Null’ interface to add a null or blackhole route to the switch. A null or

blackhole route is a routing table entry that does not forward packets, so any

packets sent to it are dropped.

Parameter Description

<subnet&mask>The IPv4 address of the destination subnet defined using either a

prefix length or a separate mask specified in one of the following

formats:

• The IPv4 subnet address in dotted decimal notation followed by

the subnet mask, also in dotted decimal notation.

• The IPv4 subnet address in dotted decimal notation, followed

by a forward slash, then the prefix length

<gateway-ip>The IPv4 address of the gateway device.

<interface>The interface that connects your device to the network. Enter the

name of the VLAN or its VID. You can also enter ‘null’ as an

interface. Specify a ‘null’ interface to add a null or blackhole route

to the device.

The gateway IP address or the interface is required.

<distance>The administrative distance for the static route in the range

<1-255>. Static routes by default have an administrative distance

of 1.

613-50137-01 Rev A Command Reference for FS980M Series 635

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

ROUTING COMMANDS

IP ROUTE

Examples To add the destination 192.168.3.0 with the mask 255.255.255.0 as a static route

available through the device at “10.10.0.2” with the default administrative

distance, use the commands:

awplus# configure terminal

awplus(config)# ip route 192.168.3.0 255.255.255.0 10.10.0.2

To remove the destination 192.168.3.0 with the mask 255.255.255.0 as a static

route available through the device at “10.10.0.2” with the default administrative

distance, use the commands:

awplus# configure terminal

awplus(config)# no ip route 192.168.3.0 255.255.255.0 10.10.0.2

To specify a null or blackhole route 192.168.4.0/24, so packets forwarded to this

route are dropped, use the commands:

awplus# configure terminal

awplus(config)# ip route 192.168.4.0/24 null

To add the destination 192.168.3.0 with the mask 255.255.255.0 as a static route

available through the device at “10.10.0.2” with an administrative distance of 128,

use the commands:

awplus# configure terminal

awplus(config)# ip route 192.168.3.0 255.255.255.0 10.10.0.2

128

Commands

show ip route

show ip route database

613-50137-01 Rev A Command Reference for FS980M Series 636

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

ROUTING COMMANDS

IPV6 ROUTE

ipv6 route

Overview This command adds a static IPv6 route to the Routing Information Base (RIB). If this

route is the best route for the destination, then your device adds it to the

Forwarding Information Base (FIB). Your device uses the FIB to advertise routes to

neighbors and forward packets.

The no variant of this command removes the static route.

Syntax ipv6 route <dest-prefix> <dest-prefix/length>

{<gateway-ip>|<gateway-name>} [<distvalue>]

no ipv6 route <dest-prefix> <dest-prefix/length>

{<gateway-ip>|<gateway-name>} [<distvalue>]

Mode Global Configuration

Usage Administrative distance can be modified so static routes do not take priority over

other routes.

Example awplus# configure terminal

awplus(config)# ipv6 route 2001:0db8::1/128 vlan2 32

Validation

Commands

show running-config

show ipv6 route

Parameter Description

<dest-prefix/

length>

Specifies the IP destination prefix.

The IPv6 address prefix uses the format X:X::/prefix-length.

The prefix-length is usually set between 0 and 64.

<gateway-ip>Specifies the IP gateway (or next hop) address. The IPv6

address uses the format X:X::X:X/Prefix-Length. The

prefix-length is usually set between 0 and 64.

<gateway-name>Specifies the name of the gateway (or next hop) interface.

<distvalue>Specifies the administrative distance for the route. Valid

values are from 1 to 255.

613-50137-01 Rev A Command Reference for FS980M Series 637

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

ROUTING COMMANDS

MAXIMUM-PATHS

maximum-paths

Overview This command enables ECMP on your device, and sets the maximum number of

paths that each route has in the Forwarding Information Base (FIB). ECMP is

enabled by default.

The no variant of this command sets the maximum paths to the default of 4.

Syntax maximum-paths <1-8>

no maximum-paths

Default By default the maximum number of paths is 4.

Mode Global Configuration

Examples To set the maximum number of paths for each route in the FIB to 5, use the

command:

awplus# configure terminal

awplus(config)# maximum-paths 5

To set the maximum paths for a route to the default of 4, use the command:

awplus# configure terminal

awplus(config)# no maximum-paths

Parameter Description

<1-8> The maximum number of paths that a route can have in the FIB.

613-50137-01 Rev A Command Reference for FS980M Series 638

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

ROUTING COMMANDS

SHOW IP ROUTE

show ip route

Overview Use this command to display routing entries in the FIB (Forwarding Information

Base). The FIB contains the best routes to a destination, and your device uses these

routes when forwarding traffic. You can display a subset of the entries in the FIB

based on protocol.

To modify the lines displayed, use the | (output modifier token); to save the output

to a file, use the > output redirection token.

Syntax show ip route [connected|rip|static|<ip-addr>|

<ip-addr/prefix-length>]

Mode User Exec and Privileged Exec

Example To display the static routes in the FIB, use the command:

awplus# show ip route static

Output Each entry in the output from this command has a code preceding it, indicating the

source of the routing entry. The first few lines of the output list the possible codes

that may be seen with the route entries.

Typically, route entries are composed of the following elements:

•code

• a second label indicating the sub-type of the route

• network or host IP address

• administrative distance and metric

• next hop IP address

• outgoing interface name

• time since route entry was added

Parameter Description

connected Displays only the routes learned from connected

interfaces.

rip Displays only the routes learned from RIP.

static Displays only the static routes you have configured.

<ip-addr> Displays the routes for the specified address. Enter

an IPv4 address.

<ip-addr/prefix-length> Displays the routes for the specified network. Enter

an IPv4 address and prefix length.

613-50137-01 Rev A Command Reference for FS980M Series 639

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

ROUTING COMMANDS

SHOW IP ROUTE

Figure 20-1: Example output from the show ip route command

Connected Route The connected route entry consists of:

This route entry denotes:

• Route entries for network 10.10.31.0/24 are derived from the IP address

of local interface vlan2.

• These routes are marked as Connected routes (C) and always preferred

over routes for the same network learned from other routing protocols.

Commands

ip route

maximum-paths

show ip route database

Codes: C - connected, S - static, R - RIP, B - BGP

O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2

* - candidate default



C 3.3.3.0/24 is directly connected, vlan1

C 10.10.31.0/24 is directly connected, vlan2

C 10.70.0.0/24 is directly connected, vlan4

C 33.33.33.33/32 is directly connected, lo

C 10.10.31.0/24 is directly connected, vlan2

613-50137-01 Rev A Command Reference for FS980M Series 640

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

ROUTING COMMANDS

SHOW IP ROUTE DATABASE

show ip route database

Overview This command displays the routing entries in the RIB (Routing Information Base).

When multiple entries are available for the same prefix, RIB uses the routes’

administrative distances to choose the best route. All best routes are entered into

the FIB (Forwarding Information Base). To view the routes in the FIB, use the show

ip route command.

To modify the lines displayed, use the | (output modifier token); to save the output

to a file, use the > output redirection token.

Syntax show ip route database [connected|static]

Mode User Exec and Privileged Exec

Example To display the static routes in the RIB, use the command:

awplus# show ip route database static

Output Figure 20-2: Example output from the show ip route database command

Commands

maximum-paths

show ip route

Parameter Description

connected Displays only the routes learned from connected interfaces.

static Displays only the static routes you have configured.

awplus#show ip route database

Codes: C - connected, S - static, R - RIP, B - BGP

O - OSPF, D - DHCP, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2

> - selected route, * - FIB route, p - stale info



S *> 0.0.0.0/0 [1/0] via 10.34.1.1, vlan1

C *> 10.34.0.0/16 is directly connected, vlan1

S 192.168.2.0/24 [1/0] is directly connected, vlan2 inactive



Gateway of last resort is not set

613-50137-01 Rev A Command Reference for FS980M Series 641

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

ROUTING COMMANDS

SHOW IP ROUTE SUMMARY

show ip route summary

Overview This command displays a summary of the current RIB (Routing Information Base)

entries.

To modify the lines displayed, use the | (output modifier token); to save the output

to a file, use the > output redirection token.

Syntax show ip route summary

Mode User Exec and Privileged Exec

Example To display a summary of the current RIB entries, use the command:

awplus# show ip route summary

Output Figure 20-3: Example output from the show ip route summary command

Commands

show ip route

show ip route database

IP routing table name is Default-IP-Routing-Table(0)

IP routing table maximum-paths is 4

Route Source Networks

connected 5

Total 8

613-50137-01 Rev A Command Reference for FS980M Series 642

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

ROUTING COMMANDS

SHOW IPV6 ROUTE

show ipv6 route

Overview Use this command to display the IPv6 routing table for a protocol or from a

particular table.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ipv6 route

[connected|database|summary|<ipv6-address>|<ipv6-addr/prefix-l

ength>)]

Mode User Exec and Privileged Exec

Example 1 To display an IP route with all parameters turned on, use the following command:

awplus# show ipv6 route

Output Figure 20-4: Example output of the show ipv6 route command

Parameter Description

connected Displays only the routes learned from connected

interfaces.

database Displays only the IPv6 routing information extracted

from the database.

summary Displays summary information from the IPv6 routing

table.

<ipv6-address> Displays the routes for the specified address in the IP

routing table. The IPv6 address uses the format

X:X::X:X/Prefix-Length. The prefix-length is usually set

between 0 and 64.

<ipv6-prefix/length> Displays only the routes for the specified IP prefix.



IPv6 Routing Table

Codes: C - connectedS ::/0 [1/0] via 2001::a:0:0:c0a8:a6, vlan10

C 2001:db8::a:0:0:0:0/64 via ::, vlan10

C 2001:db8::14:0:0:0:0/64 via ::, vlan20

C 2001:db8::0:0:0:0/64 via ::, vlan30

C 2001:db8::28:0:0:0:0/64 via ::, vlan40

C 2001:db8::fa:0:0:0:0/64 via ::, vlan250

C 2001:db8::/64 via ::, vlan250

C 2001:db8::/64 via ::, vlan40

C 2001:db8::/64 via ::, vlan20

C 2001:db8::/64 via ::, vlan10

613-50137-01 Rev A Command Reference for FS980M Series 643

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

ROUTING COMMANDS

SHOW IPV6 ROUTE

Example 2 To display all database entries for an IP route, use the following command:

awplus# show ipv6 route database

Output Figure 20-5: Example output of the show ipv6 route database command



IPv6 Routing Table

Codes: C - connected> - selected route, * - FIB route, p - stale

info

Timers: Uptime



S ::/0 [1/0] via 2001::a:0:0:c0a8:a01 inactive, 6d22h12m

[1/0] via 2001::fa:0:0:c0a8:fa01 inactive, 6d22h12m

613-50137-01 Rev A Command Reference for FS980M Series 644

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

ROUTING COMMANDS

SHOW IPV6 ROUTE SUMMARY

show ipv6 route summary

Overview Use this command to display the summary of the current NSM RIB entries.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ipv6 route summary

Mode User Exec and Privileged Exec

Example To display IP route summary, use the following command:

awplus# show ipv6 route summary

Output Figure 20-6: Example output from the show ipv6 route summary command

Commands

show ip route database

IPv6 routing table name is Default-IPv6-Routing-Table(0)

IPv6 routing table maximum-paths is 4

RouteSource Networks

connected 4

Total 4

FIB 0

613-50137-01 Rev A Command Reference for FS980M Series 645

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP Commands

Introduction

Overview This chapter provides an alphabetical reference of commands used to configure

RIP.

For information about configuring RIP, see the RIP Feature Overview and

Configuration Guide.

Command List •“accept-lifetime” on page 647

•“alliedware-behavior” on page 649

•“cisco-metric-behavior (RIP)” on page 651

•“clear ip rip route” on page 652

•“debug rip” on page 653

•“default-information originate (RIP)” on page 654

•“default-metric (RIP)” on page 655

•“distance (RIP)” on page 656

•“distribute-list (RIP)” on page 657

•“fullupdate (RIP)” on page 658

•“ip rip authentication key-chain” on page 659

•“ip rip authentication mode” on page 661

•“ip rip authentication string” on page 664

•“ip rip receive-packet” on page 666

•“ip rip receive version” on page 667

•“ip rip send-packet” on page 668

•“ip rip send version” on page 669

•“ip rip send version 1-compatible” on page 671

613-50137-01 Rev A Command Reference for FS980M Series 646

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

•“ip rip split-horizon” on page 673

•“key” on page 674

•“key chain” on page 675

•“key-string” on page 676

•“maximum-prefix” on page 677

•“neighbor (RIP)” on page 678

•“network (RIP)” on page 679

•“offset-list (RIP)” on page 680

•“passive-interface (RIP)” on page 681

•“recv-buffer-size (RIP)” on page 682

•“redistribute (RIP)” on page 683

•“restart rip graceful” on page 684

•“rip restart grace-period” on page 685

•“route (RIP)” on page 686

•“router rip” on page 687

•“send-lifetime” on page 688

•“show debugging rip” on page 690

•“show ip protocols rip” on page 691

•“show ip rip” on page 692

•“show ip rip database” on page 693

•“show ip rip interface” on page 694

•“timers (RIP)” on page 695

•“undebug rip” on page 696

•“version (RIP)” on page 697

613-50137-01 Rev A Command Reference for FS980M Series 647

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

ACCEPT-LIFETIME

accept-lifetime

Overview Use this command to specify the time period during which the authentication key

on a key chain is received as valid.

Use the no variant of this command to remove a specified time period for an

authentication key on a key chain as set previously with the accept-lifetime

command.

Syntax accept-lifetime <start-date> {<end-date>|

duration <seconds>|infinite}

no accept-lifetime

Mode Keychain-key Configuration

Examples The following examples show the setting of accept-lifetime for key 1 on the key

chain named “mychain”.

awplus# configure terminal

awplus(config)# key chain mychain

awplus(config-keychain)# key 1

awplus(config-keychain-key)# accept-lifetime 03:03:01 Sep 3

2016 04:04:02 Oct 6 2016

Parameter Description

<start-date> Specifies the start time and date in the format: 

<hh:mm:ss> <day> <month> <year> or 

<hh:mm:ss> <month> <day> <year>, where:

<hh:mm:ss> The time of the day, in hours, minutes and seconds

<day> <1-31> The day of the month

<month> The month of the year (the first three letters of the

month, for example, Jan)

<year> <1993-2035> The year

<end-date> Specifies the end time and date in the format: 

<hh:mm:ss> <day> <month> <year> or 

<hh:mm:ss> <month> <day> <year>, where:

<hh:mm:ss> The time of the day, in hours, minutes and seconds

<day> <1-31> The day of the month

<month> The month of the year (the first three letters of the

month, for example, Jan)

<year> <1993-2035> The year

<seconds> <1-2147483646> Duration of the key in seconds.

infinite Never expires.

613-50137-01 Rev A Command Reference for FS980M Series 648

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

ACCEPT-LIFETIME

or:

awplus# configure terminal

awplus(config)# key chain mychain

awplus(config-keychain)# key 1

awplus(config-keychain-key)# accept-lifetime 03:03:01 3 Sep

2016 04:04:02 6 Oct 2016

Commands

key

key-string

key chain

send-lifetime

613-50137-01 Rev A Command Reference for FS980M Series 649

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

ALLIEDWARE-BEHAVIOR

alliedware-behavior

Overview This command configures your device to exhibit AlliedWare behavior when

sending RIPv1 response/update messages. Configuring for this behavior may be

necessary if you are replacing an AlliedWare device with an AlliedWare Plus device

and wish to ensure consistent RIPv1 behavior.

Use the no variant of this command to implement AlliedWare Plus behavior.

This command has no impact on devices running RIPv2. Reception and

transmission can be independently altered to conform to AlliedWare standard.

Syntax alliedware-behavior {rip1-send|rip1-recv}

no alliedware-behavior {rip1-send|rip1-recv}

Default By default when sending out RIPv1 updates on an interface, if the prefix (learned

through RIPv2 or otherwise redistributed into RIP) being advertised does not

match the subnetting used on the outgoing RIPv1 interface it will be filtered. The

alliedware-behavior command returns your router’s RIPv1 behavior to the

AlliedWare format, where the prefix will be advertised as-is.

For example, if a RIPv1 update is being sent over interface 192.168.1.4/26, by

default the prefix 192.168.1.64/26 will be advertised, but the prefix

192.168.1.144/28 will be filtered because the mask /28 does not match the

interface's mask of /26. If alliedware- behavior r ip1-send is configured, the prefix

192.168.1.144 would be sent as-is.

Mode Router Configuration

Examples To configure your device for alliedware-behavior when sending and receiving

RIPv1 update messages, enter the commands:

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# alliedware-behavior rip1-send

awplus(config-router)# alliedware-behavior rip1-recv

Parameter Description

rip1-send Configures the router to behave in AlliedWare mode when sending

update messages.

rip1-recv Configures the router to behave in AlliedWare mode when receiving

update messages.

613-50137-01 Rev A Command Reference for FS980M Series 650

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

ALLIEDWARE-BEHAVIOR

To return your device to AlliedWare Plus-like behavior when sending and

receiving RIPv1 update messages, enter the commands:

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# no alliedware-behavior rip1-send

awplus(config-router)# no alliedware-behavior rip1-recv

Validation

Commands

show ip protocols rip

show running-config

Commands

fullupdate (RIP)

613-50137-01 Rev A Command Reference for FS980M Series 651

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

CISCO-METRIC-BEHAVIOR (RIP)

cisco-metric-behavior (RIP)

Overview Use this command to enable or disable the RIP routing metric update to conform

to Cisco’s implementation. This command is provided to allow inter-operation

with older Cisco devices that do not conform to the RFC standard for RIP route

metrics.

Use the no variant of this command to disable this feature.

Syntax cisco-metric-behavior {enable|disable}

no cisco-metric-behavior

Default By default, the Cisco metric-behavior is disabled.

Mode Router Configuration

Examples To enable the routing metric update to behave as per the Cisco implementation,

enter the commands:

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# cisco-metric-behavior enable

To disable the routing metric update to behave as per the default setting, enter the

commands:

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# no cisco-metric-behavior

Validation

Commands

show running-config

Parameter Description

enable Enables updating the metric consistent with Cisco.

disable Disables updating the metric consistent with Cisco.

613-50137-01 Rev A Command Reference for FS980M Series 652

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

CLEAR IP RIP ROUTE

clear ip rip route

Overview Use this command to clear specific data from the RIP routing table.

Mode Privileged Exec

Usage Using this command with the all parameter clears the RIP table of all the routes.

Examples To clear the route 10.0.0.0/8 from the RIP routing table, use the following

command:

awplus# clear ip rip route 10.0.0.0/8

Parameter Description

<ip-dest-network/

prefix-length>

Removes entries which exactly match this destination

address from RIP routing table. Enter the IP address and

prefix length of the destination network.

static Removes static entries from the RIP routing table.

connected Removes entries for connected routes from the RIP routing

table.

rip Removes only RIP routes from the RIP routing table.

ospf Removes only OSPF routes from the RIP routing table.

invalid-routes Removes routes with metric 16 immediately. Otherwise,

these routes are not removed until RIP times out the route

after 2 minutes.

all Clears the entire RIP routing table.

613-50137-01 Rev A Command Reference for FS980M Series 653

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

DEBUG RIP

debug rip

Overview Use this command to specify the options for the displayed debugging information

for RIP events and RIP packets.

Use the no variant of this command to disable the specified debug option.

Syntax debug rip {events|nsm|<packet>|all}

no debug rip {events|nsm|<packet>|all}

Default Disabled

Mode Privileged Exec and Global Configuration

Example The following example displays information about the RIP packets that are

received and sent out from the device.

awplus# debug rip packet

Commands

undebug rip

Parameter Description

events RIP events debug information is displayed.

nsm RIP and NSM communication is displayed.

<packet>packet [recv|send] [detail] Specifies RIP packets only.

recv Specifies that information for received packets be displayed.

send Specifies that information for sent packets be displayed.

detail Displays detailed information for the sent or received packet.

all Displays all RIP debug information.

613-50137-01 Rev A Command Reference for FS980M Series 654

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

DEFAULT-INFORMATION ORIGINATE (RIP)

default-information originate (RIP)

Overview Use this command to generate a default route into the Routing Information

Protocol (RIP).

Use the no variant of this command to disable this feature.

Syntax default-information originate

no default-information originate

Default Disabled

Mode Router Configuration

Usage If routes are being redistributed into RIP and the router’s route table contains a

default route, within one of the route categories that are being redistributed, the

RIP protocol will advertise this default route, irrespective of whether the

default-information originate command has been configured or not. However,

if the router has not redistributed any default route into RIP, but you want RIP to

advertise a default route anyway, then use this command.

This will cause RIP to create a default route entry in the RIP database. The entry will

be of type RS (Rip Static). Unless actively filtered out, this default route will be

advertised out every interface that is sending RIP. Split horizon does not apply to

this route, as it is internally generated. This operates quite similarly to the OSPF

default-information originate always command.

Example awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# default-information originate

613-50137-01 Rev A Command Reference for FS980M Series 655

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

DEFAULT-METRIC (RIP)

default-metric (RIP)

Overview Use this command to specify the metrics to be assigned to redistributed RIP routes.

Use the no variant of this command to reset the RIP metric back to its default (1).

Syntax default-metric <metric>

no default-metric [<metric>]

Default By default, the RIP metric value is set to 1.

Mode RIP Router Configuration

Usage This command is used with the redistribute (RIP) command to make the routing

protocol use the specified metric value for all redistributed routes, regardless of

the original protocol that the route has been redistributed from.

Examples This example assigns the cost of 10 to the routes that are redistributed into RIP.

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# default-metric 10

awplus(config-router)# redistribute ospf

awplus(config-router)# redistribute connected

Commands

redistribute (RIP)

Parameter Description

<metric> <1-16> Specifies the value of the default metric.

613-50137-01 Rev A Command Reference for FS980M Series 656

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

DISTANCE (RIP)

distance (RIP)

Overview This command sets the administrative distance for RIP routes. Your device uses this

value to select between two or more routes to the same destination obtained from

two different routing protocols. The route with the smallest administrative

distance value is added to the Forwarding Information Base (FIB). For more

information, see the Route Selection Feature Overview and Configuration Guide.

The no variant of this command sets the administrative distance for the RIP route

to the default of 120.

Syntax distance <1-255> [<ip-addr/prefix-length> [<access-list>]]

no distance [<1-255>] [<ip-addr/prefix-length> [ <access-list>]]

Mode RIP Router Configuration

Examples To set the administrative distance to 8 for the RIP routes within the 10.0.0.0/8

network that match the access-list “mylist”, use the commands:

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# distance 8 10.0.0.0/8 mylist

To set the administrative distance to the default of 120 for the RIP routes within the

10.0.0.0/8 network that match the access-list “mylist”, use the commands:

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# no distance 8 10.0.0.0/8 mylist

Parameter Description

<1-255> The administrative distance value you are setting for this RIP

route.

<ip-addr/

prefix-length>

The network IP address and prefix-length that you are changing

the administrative distance for.

<access-list> Specifies the access-list name. This access list specifies which

routes within the specified network this command applies to.

613-50137-01 Rev A Command Reference for FS980M Series 657

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

DISTRIBUTE-LIST (RIP)

distribute-list (RIP)

Overview Use this command to filter incoming or outgoing route updates using the

access-list or the prefix-list.

Use the no variant of this command to disable this feature.

Syntax distribute-list {<access-list> | prefix <prefix-list>} {in|out}

[<interface>]

no distribute-list {<access-list> | prefix <prefix-list>}

{in|out} [<interface>]

Default Disabled

Mode RIP Router Configuration

Usage Filter out incoming or outgoing route updates using access-list or prefix-list. If you

do not specify the name of the interface, the filter will be applied to all interfaces.

Examples In this example the following commands are used to apply an access list called

myfilter to filter incoming routing updates in vlan2

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# distribute-list prefix myfilter in vlan2

Parameter Description

prefix Filter prefixes in routing updates.

<access-list> Specifies the IPv4 access-list number or name to use.

<prefix-list> Specifies the name of the IPv4 prefix-list to use.

in Filter incoming routing updates.

out Filter outgoing routing updates.

<interface>The interface on which distribute-list applies. For instance: vlan2

613-50137-01 Rev A Command Reference for FS980M Series 658

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

FULLUPDATE (RIP)

fullupdate (RIP)

Overview Use this command to specify which routes RIP should advertise when performing

a triggered update. By default, when a triggered update is sent, RIP will only

advertise those routes that have changed since the last update. When fullupdate

is configured, the device advertises the full RIP route table in outgoing triggered

updates, including routes that have not changed. This enables faster convergence

times, or allow inter-operation with legacy network equipment, but at the expense

of larger update messages.

Use the no variant of this command to disable this feature.

Syntax fullupdate

no fullupdate

Default By default this feature is disabled.

Mode RIP Router Configuration

Example To enable the fullupdate (RIP) function, use the commands:

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# fullupdate

613-50137-01 Rev A Command Reference for FS980M Series 659

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

IP RIP AUTHENTICATION KEY-CHAIN

ip rip authentication key-chain

Overview Use this command to enable RIPv2 authentication on an interface and specify the

name of the key chain to be used.

Use the no variant of this command to disable this function.

Syntax ip rip authentication key-chain <key-chain-name>

no ip rip authentication key-chain

Mode Interface Configuration for a VLAN interface.

Usage Use this command to perform authentication on the interface. Not configuring the

key chain results in no authentication at all.

The AlliedWare Plus™ implementation provides the choice of configuring

authentication for single key or multiple keys at different times. Use the ip rip

authentication string command for single key authentication. Use the ip rip

authentication key-chain command for multiple keys authentication. See the RIP

Feature Overview and Configuration Guide for illustrated RIP configuration

examples.

For multiple key authentication, use the following steps to configure a route to

enable RIPv2 authentication using multiple keys at different times:

1) Define a key chain with a key chain name, using the following commands:

awplus# configure terminal

awplus(config)# key chain <key-chain-name>

2) Define a key on this key chain, using the following command:

awplus(config-keychain)# key <keyid>

3) Define the password used by the key, using the following command:

awplus(config-keychain-key)# key-string <key-password>

4) Enable authentication on the desired interface and specify the key chain to

be used, using the following commands:

awplus# configure terminal

awplus(config)# interface <id>

awplus(config-if)# ip rip authentication key-chain

<key-chain-name>

Parameter Description

<key-chain-name>Specify the name of the key chain. This is an alpha-numeric

string, but it cannot include spaces.

613-50137-01 Rev A Command Reference for FS980M Series 660

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

IP RIP AUTHENTICATION KEY-CHAIN

5) Specify the mode of authentication for the given interface (text or MD5),

using the following command:

awplus(config-if)# ip rip authentication mode {md5|text}

Example In the following example of a configuration for multiple keys authentication, a

password “toyota” is set for key 1 in key chain “cars”. Authentication is enabled on

vlan2 and the authentication mode is set to MD5:

awplus# configure terminal

awplus(config)# key chain cars

awplus(config-keychain)# key 1

awplus(config-keychain-key)# key-string toyota

awplus(config-keychain-key)# accept-lifetime 10:00:00 Oct 08

2016 duration 43200

awplus(config-keychain-key)# send-lifetime 10:00:00 Oct 08 2016

duration 43200

awplus(config-keychain-key)# exit

awplus(config-keychain)# exit

awplus(config)# interface vlan2

awplus(config-if)# ip rip authentication key-chain cars

awplus(config-if)# ip rip authentication mode md5

Example In the following example, the VLAN interface vlan23 is configured to use key-chain

authentication with the keychain “mykey”. See the key command for a description

of how a key chain is created.

awplus# configure terminal

awplus(config)# interface vlan23

awplus(config-if)# ip rip authentication key-chain mykey

Commands

accept-lifetime

send-lifetime

ip rip authentication mode

ip rip authentication string

key

key chain

613-50137-01 Rev A Command Reference for FS980M Series 661

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

IP RIP AUTHENTICATION MODE

ip rip authentication mode

Overview Use this command to specify the type of authentication mode used for RIP v2

packets.

Use the no variant of this command to restore clear text authentication.

Syntax ip rip authentication mode {md5|text}

no ip rip authentication mode

Default Text authentication is enabled

Mode Interface Configuration for a VLAN interface.

Usage The AlliedWare Plus™ implementation provides the choice of configuring

authentication for single key or multiple keys at different times. Use the ip rip

authentication string command for single key authentication. Use the ip rip

authentication key-chain command for multiple keys authentication. See the RIP

Feature Overview and Configuration Guide for illustrated RIP configuration

examples.

Usage: single key Use the following steps to configure a route to enable RIPv2 authentication using

a single key or password:

1) Define the authentication string or password used by the key for the desired

interface, using the following commands:

awplus# configure terminal

awplus(config)# interface <id>

awplus(config-if)# ip rip authentication string

<auth-string>

2) Specify the mode of authentication for the given interface (text or MD5),

using the following commands:

awplus# configure terminal

awplus(config)# interface <id>

awplus(config-if)# ip rip authentication mode {md5|text}

Parameter Description

md5 Uses the keyed MD5 authentication algorithm.

text Specifies clear text or simple password authentication.

613-50137-01 Rev A Command Reference for FS980M Series 662

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

IP RIP AUTHENTICATION MODE

Usage: multiple

key

For multiple keys authentication, use the following steps to configure a route to

enable RIPv2 authentication using multiple keys at different times:

1) Define a key chain with a key chain name, using the following commands:

awplus# configure terminal

awplus(config)# key chain <key-chain-name>

2) Define a key on this key chain using the following command:

awplus(config-keychain)# key <keyid>

3) Define the password used by the key, using the following command:

awplus(config-keychain-key)# key-string <key-password>

4) Enable authentication on the desired interface and specify the key chain to

be used, using the following commands:

awplus(config-if)# ip rip authentication key-chain

<key-chain-name>

5) Specify the mode of authentication for the given interface (text or MD5),

using the following commands:

awplus(config-if)# ip rip authentication mode {md5|text}

Example 1 In the following example of a configuration for multiple keys authentication, a

password of “toyota” is set for key 1 in key chain “cars”. Authentication is enabled

on vlan2 and the authentication mode is set to MD5:

awplus# configure terminal

awplus(config)# key chain cars

awplus(config-keychain)# key 1

awplus(config-keychain-key)# key-string toyota

awplus(config-keychain-key)# accept-lifetime 10:00:00 Oct 08

2016 duration 43200

awplus(config-keychain-key)# send-lifetime 10:00:00 Oct 08 2016

duration 43200

awplus(config-keychain-key)# exit

awplus(config-keychain)# exit

awplus(config)# interface vlan2

awplus(config-if)# ip rip authentication key-chain cars

awplus(config-if)# ip rip authentication mode md5

Example 2 The following example shows MD5 authentication configured on VLAN interface

vlan2, ensuring authentication of RIP packets received on this interface.

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ip rip authentication mode md5

613-50137-01 Rev A Command Reference for FS980M Series 663

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

IP RIP AUTHENTICATION MODE

Example 3 The following example specifies “mykey” as the authentication string with MD5

authentication, for the VLAN interface vlan2:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ip rip authentication string mykey

awplus(config-if)# ip rip authentication mode md5

Commands

ip rip authentication string

ip rip authentication key-chain

613-50137-01 Rev A Command Reference for FS980M Series 664

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

IP RIP AUTHENTICATION STRING

ip rip authentication string

Overview Use this command to specify the authentication string or password used by a key.

Use the no variant of this command to remove the authentication string.

Syntax ip rip authentication string <auth-string>

no ip rip authentication string

Mode Interface Configuration for a VLAN interface.

Usage The AlliedWare Plus™ implementation provides the choice of configuring

authentication for single key or multiple keys at different times. Use this command

to specify the password for a single key on an interface. Use the ip rip

authentication key-chain command for multiple keys authentication. For

information about configuring RIP, see the RIP Feature Overview and

Configuration Guide.

Use the following steps to configure a route to enable RIPv2 authentication using

a single key or password:

1) Define the authentication string or password used by the key for the desired

interface, using the following commands:

awplus# configure terminal

awplus(config)# interface <id>

2) Specify the mode of authentication for the given interface (text or MD5),

using the following commands:

awplus# configure terminal

awplus(config-if)# ip rip authentication string

<auth-string>

awplus(config)# interface <id>

awplus(config-if)# ip rip authentication mode {md5|text}

Example See the example below to specify mykey as the authentication string with MD5

authentication for the VLAN interface vlan2:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ip rip authentication string mykey

awplus(config-if)# ip rip authentication mode md5

Parameter Description

<auth-string> The authentication string or password used by a key. It is an alpha-

numeric string and can include spaces.

613-50137-01 Rev A Command Reference for FS980M Series 665

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

IP RIP AUTHENTICATION STRING

Example In the following example, the VLAN interface vlan2 is configured to have an

authentication string as guest. Any received RIP packet in that interface should

have the same string as password.

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ip rip authentication string guest

commands

ip rip authentication key-chain

ip rip authentication mode

613-50137-01 Rev A Command Reference for FS980M Series 666

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

IP RIP RECEIVE-PACKET

ip rip receive-packet

Overview Use this command to configure the interface to enable the reception of RIP

packets.

Use the no variant of this command to disable this feature.

Syntax ip rip receive-packet

no ip rip receive-packet

Default Receive-packet is enabled

Mode Interface Configuration for a VLAN interface.

Example This example shows packet receiving being turned on for the VLAN interface

vlan3:

awplus# configure terminal

awplus(config)# interface vlan3

awplus(config-if)# ip rip receive-packet

Commands

ip rip send-packet

613-50137-01 Rev A Command Reference for FS980M Series 667

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

IP RIP RECEIVE VERSION

ip rip receive version

Overview Use this command to specify the version of RIP packets accepted on an interface

and override the setting of the version command.

Use the no variant of this command to use the setting specified by the version (RIP)

command.

Syntax ip rip receive version {[1][2]}

no ip rip receive version

Default Version 2

Mode Interface Configuration for a VLAN interface.

Usage This command applies to a specific VLAN interface and overrides any the version

specified by the version (RIP) command.

RIP can be run in version 1 or version 2 mode. Version 2 has more features than

version 1; in particular RIP version 2 supports authentication and classless routing.

Once the RIP version is set, RIP packets of that version will be received and sent on

all the RIP-enabled interfaces.

Example In the following example, the VLAN interface vlan3 is configured to receive both

RIP version 1 and 2 packets:

awplus# configure terminal

awplus(config)# interface vlan3

awplus(config-if)# ip rip receive version 1 2

Commands

version (RIP)

Parameter Description

1Specifies acceptance of RIP version 1 packets on the interface.

2Specifies acceptance of RIP version 2 packets on the interface.

613-50137-01 Rev A Command Reference for FS980M Series 668

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

IP RIP SEND-PACKET

ip rip send-packet

Overview Use this command to enable sending RIP packets through the current interface.

Use the no variant of this command to disable this feature.

Syntax ip rip send-packet

no ip rip send-packet

Default Send packet is enabled

Mode Interface Configuration for a VLAN interface.

Example This example shows packet sending being turned on for the VLAN interface

vlan4:

awplus# configure terminal

awplus(config)# interface vlan4

awplus(config-if)# ip rip send-packet

Commands

ip rip receive-packet

613-50137-01 Rev A Command Reference for FS980M Series 669

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

IP RIP SEND VERSION

ip rip send version

Overview Use this command in Interface Configuration mode to specify the version of RIP

packets sent on an interface and override the setting of the version (RIP)

command. This mechanism causes RIP version 2 interfaces to send multicast

packets instead of broadcasting packets.

Use the no variant of this command to use the setting specified by the version (RIP)

command.

Syntax ip rip send version {1|2|1 2|2 1}

no ip rip send version

Default RIP version 2 is enabled by default.

Mode Interface Configuration for a VLAN interface.

Usage This command applies to a specific interface and overrides the version specified by

the version (RIP) command.

RIP can be run in version 1 or version 2 mode. Version 2 has more features than

version 1; in particular RIP version 2 supports authentication and classless routing.

Once the RIP version is set, RIP packets of that version will be received and sent on

all the RIP-enabled interfaces. Selecting version parameters 1 2 or 2 1 sends RIP

version 1 and 2 packets.

Use the ip rip send version 1-compatible command in an environment where you

cannot send multicast packets. For example, in environments where multicast is

not enabled and where hosts do not listen to multicast.

Examples In the following example, the VLAN interface vlan4 is configured to send both RIP

version 1 and 2 packets.

awplus# configure terminal

awplus(config)# interface vlan4

awplus(config-if)# ip rip send version 1 2

Parameter Description

1Specifies the sending of RIP version 1 packets out of an interface.

2Specifies the sending of RIP version 2 packets out of an interface.

12 Specifies the sending of both RIP version 1 and RIP version 2

packets out of an interface.

21 Specifies the sending of both RIP version 2 and RIP version 1

packets out of an interface.

613-50137-01 Rev A Command Reference for FS980M Series 670

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

IP RIP SEND VERSION

In the following example, the VLAN interface vlan4 is configured to send both RIP

version 2 and 1 packets.

awplus# configure terminal

awplus(config)# interface vlan4

awplus(config-if)# ip rip send version 2 1

In the following example, the VLAN interface vlan4 is configured to send RIP

version 1 packets only.

awplus# configure terminal

awplus(config)# interface vlan4

awplus(config-if)# ip rip send version 1

In the following example, the VLAN interface vlan4 is configured to send RIP

version 2 packets only.

awplus# configure terminal

awplus(config)# interface vlan4

awplus(config-if)# ip rip send version 2

In the following example, the VLAN interface vlan3 is configured to use the RIP

version specified by the version (RIP) command.

awplus# configure terminal

awplus(config)# interface vlan3

awplus(config-if)# no ip rip send version

Commands

ip rip send version 1-compatible

version (RIP)

613-50137-01 Rev A Command Reference for FS980M Series 671

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

IP RIP SEND VERSION 1-COMPATIBLE

ip rip send version 1-compatible

Overview Use this command in Interface Configuration mode to send RIP version 1

compatible packets from a RIP version 2 interfaces to other RIP Interfaces. This

mechanism causes RIP version 2 interfaces to send broadcast packets instead of

multicasting packets, and is used in environments where multicast is not enabled

or where hosts do not listen to multicast.

Use the no variant of this command to use the setting specified by the version (RIP)

command, and disable the broadcast of RIP version 2 packets that are sent as

broadcast packets.

Syntax ip rip send version 1-compatible

no ip rip send version

Default RIP version 2 is enabled by default.

Mode Interface Configuration for a VLAN interface.

Usage This command applies to a specific interface and overrides the version specified by

the version (RIP) command.

RIP can be run in version 1 compatible mode. Version 2 has more features than

version 1; in particular RIP version 2 supports authentication and classless routing.

Once the RIP version is set, RIP packets of that version will be received and sent on

all the RIP-enabled interfaces.

Use the ip rip send version command in an environment where you can send

multicast packets. For example, in environments where multicast is enabled and

where hosts listen to multicast.

Examples In the following example, the VLAN interface vlan2 is configured to send RIP

version 1- compatible packets.

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ip rip send version 1-compatible

In the following example, the VLAN interface vlan3 is configured to use the RIP

version specified by the version (RIP) command.

awplus# configure terminal

awplus(config)# interface vlan3

awplus(config-if)# no ip rip send version

Parameter Description

1-compatible Specify this parameter to send RIP version 1 compatible packets

from a version 2 RIP interface to other RIP interfaces.

This mechanism causes version 2 RIP interfaces to broadcast

packets instead of multicasting packets.

613-50137-01 Rev A Command Reference for FS980M Series 672

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

IP RIP SEND VERSION 1-COMPATIBLE

Commands

ip rip send version

version (RIP)

613-50137-01 Rev A Command Reference for FS980M Series 673

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

IP RIP SPLIT-HORIZON

ip rip split-horizon

Overview Use this command to turn on the split-horizon mechanism on the interface.

Use the no variant of this command to disable this mechanism.

Syntax ip rip split-horizon [poisoned]

no ip rip split-horizon

Default Split horizon poisoned

Mode Interface Configuration for a VLAN interface.

Usage Use this command to avoid including routes in updates sent to the same gateway

from which they were learned. Without the poisoned parameter, using this

command causes routes learned from a neighbor to be omitted from updates sent

to that neighbor. With the poisoned parameter, using this command causes such

routes to be included in updates, but sets their metrics to infinity. This advertises

that these routes are not reachable.

Example To turn on split horizon poisoned on vlan2, use the following commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ip rip split-horizon poisoned

Parameter Description

poisoned Performs split-horizon with poison-reverse. See “Usage” below for

more information.

613-50137-01 Rev A Command Reference for FS980M Series 674

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

KEY

key

Overview Use this command to manage, add and delete authentication keys in a key-chain.

Use the no variant of this command to delete the authentication key.

Syntax key <keyid>

no key <keyid>

Mode Keychain Configuration

Usage This command allows you to enter the keychain-key mode where a password can

be set for the key.

Example The following example configures a key number 1 and shows the change into a

keychain- key command mode prompt.

awplus# configure terminal

awplus(config)# key chain mychain

awplus(config-keychain)# key 1

awplus(config-keychain-key)#

Commands

key chain

key-string

accept-lifetime

send-lifetime

Parameter Description

<keyid> <0-2147483647> Key identifier number.

613-50137-01 Rev A Command Reference for FS980M Series 675

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

KEY CHAIN

key chain

Overview Use this command to enter the key chain management mode and to configure a

key chain with a key chain name.

Use the no variant of this command to remove the key chain and all configured

keys.

Syntax key chain <key-chain-name>

no key chain <key-chain-name>

Mode Global Configuration

Usage This command allows you to enter the keychain mode from which you can specify

keys on this key chain.

Example The following example shows the creation of a key chain named mychain and the

change into keychain mode prompt.

awplus# configure terminal

awplus(config)# key chain mychain

awplus(config-keychain)#

Commands

key

key-string

accept-lifetime

send-lifetime

Parameter Description

<key-chain-name> Specify the name of the key chain to manage.

613-50137-01 Rev A Command Reference for FS980M Series 676

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

KEY-STRING

key-string

Overview Use this command to define the password to be used by a key.

Use the no variant of this command to remove a password.

Syntax key-string <key-password>

no key-string

Mode Keychain-key Configuration

Usage Use this command to specify passwords for different keys.

Examples In the following example, the password for key1 in the key chain named

mychain is set to password prime:

awplus# configure terminal

awplus(config)# key chain mychain

awplus(config-keychain)# key 1

awplus(config-keychain-key)# key-string prime

In the following example, the password for key1 in the key chain named

mychain is removed:

awplus# configure terminal

awplus(config)# key chain mychain

awplus(config-keychain)# key 1

awplus(config-keychain-key)# no key-string

Commands

key

key chain

accept-lifetime

send-lifetime

Parameter Description

<key-password> A string of characters to be used as a password by the key.

613-50137-01 Rev A Command Reference for FS980M Series 677

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

MAXIMUM-PREFIX

maximum-prefix

Overview Use this command to configure the maximum number of RIP routes stored in the

routing table.

Use the no variant of this command to disable all limiting of the number of RIP

routes stored in the routing table.

Syntax maximum-prefix <maxprefix> [<threshold>]

no maximum-prefix

Mode Router Configuration

Example To configure the maximum number of RIP routes to 150, use the following

command:

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# maximum-prefix 150

Parameter Description

<maxprefix> <1-65535> The maximum number of RIP routes allowed.

<threshold> <1-100> Percentage of maximum routes to generate a warning. The

default threshold is 75%.

613-50137-01 Rev A Command Reference for FS980M Series 678

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

NEIGHBOR (RIP)

neighbor (RIP)

Overview Use this command to specify a neighbor router. It is used for each router to which

you wish to send unicast RIP updates.

Use the no variant of this command to stop sending unicast updates to the specific

router.

Syntax neighbor <ip-address>

no neighbor <ip-address>

Default Disabled

Mode Router Configuration

Usage Use this command to exchange nonbroadcast routing information. It can be used

multiple times for additional neighbors.

The passive-interface (RIP) command disables sending routing updates on an

interface. Use the neighbor command in conjunction with the passive-interface

(RIP) to send routing updates to specific neighbors.

Example To specify the neighbor router to 1.1.1.1, use the following command:

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# passive-interface vlan1

awplus(config-router)# neighbor 1.1.1.1

Commands

passive-interface (RIP)

Parameter Description

<ip-address> The IP address of a neighboring router with which the routing

information will be exchanged.

613-50137-01 Rev A Command Reference for FS980M Series 679

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

NETWORK (RIP)

network (RIP)

Overview Use this command to activate the transmission of RIP routing information on the

defined network.

Use the no variant of this command to remove the specified network or VLAN as

one that runs RIP.

Syntax network {<network-address>[/<subnet-mask>]|<vlan-name>}

no network {<network-address>[/<subnet-mask>]|<vlan-name>}

Default Disabled

Mode RIP Router Configuration

Usage Use this command to specify networks, or VLANs, to which routing updates will be

sent and received. The connected routes corresponding to the specified network,

or VLANs, will be automatically advertised in RIP updates. RIP updates will be sent

and received within the specified network or VLAN.

Example Use the following commands to activate RIP routing updates on network

172.16.20.0/24:

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# network 172.16.20.0/24

Commands

show ip rip

show running-config

clear ip rip route

Parameter Description

<network-address>

[/<subnet-mask>]

Specifies the network address to run RIP. Entering a subnet

mask (or prefix length) for the network address is optional.

Where no mask is entered, the device will attempt to apply a

mask that is appropriate to the class (A, B, or C) of the

address entered, e.g. an IP address of 10.0.0.0 will have a

prefix length of 8 applied to it.

<vlan-name> Specify a VLAN name with up to 32 alphanumeric characters

to run RIP.

613-50137-01 Rev A Command Reference for FS980M Series 680

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

OFFSET-LIST (RIP)

offset-list (RIP)

Overview Use this command to add an offset to the in and out metrics of routes learned

through RIP.

Use the no variant of this command to remove the offset list.

Syntax offset-list <access-list> {in|out} <offset> [<interface>]

no offset-list <access-list> {in|out} <offset> [<interface>]

Default The default offset value is the metric value of the interface over which the updates

are being exchanged.

Mode RIP Router Configuration

Usage Use this command to specify the offset value that is added to the routing metric.

When the networks match the access list the offset is applied to the metrics. No

change occurs if the offset value is zero.

Examples In this example the router examines the RIP updates being sent out from interface

vlan2 and adds 5 hops to the routes matching the ip addresses specified in the

access list 8.

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# offset-list 8 in 5 vlan2

Commands

access-list (extended numbered)

Parameter Description

<access-list>Specifies the access-list number or names to apply.

in Indicates the access list will be used for metrics of incoming

advertised routes.

out Indicates the access list will be used for metrics of outgoing

advertised routes.

<offset><0-16> Specifies that the offset is used for metrics of networks

matching the access list.

<interface>An alphanumeric string that specifies the interface to match.

613-50137-01 Rev A Command Reference for FS980M Series 681

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

PASSIVE-INTERFACE (RIP)

passive-interface (RIP)

Overview Use this command to block RIP broadcasts on the interface.

Use the no variant of this command to disable this function.

Syntax passive-interface <interface>

no passive-interface <interface>

Default Disabled

Mode RIP Router Configuration

Example Use the following commands to block RIP broadcasts on vlan20:

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# passive-interface vlan20

Commands

show ip rip

Parameter Description

<interface> Specifies the interface name.

613-50137-01 Rev A Command Reference for FS980M Series 682

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

RECV-BUFFER-SIZE (RIP)

recv-buffer-size (RIP)

Overview Use this command to run-time configure the RIP UDP (User Datagram Protocol)

receive-buffer size to improve UDP reliability by avoiding UDP receive buffer

overrun.

Use the no variant of this command to reset the configured RIP UDP receive-buffer

size to the system default (196608 bits).

Syntax recv-buffer-size <8192-2147483647>

no recv-buffer-size [<8192-2147483647>]

Default 196608 bits is the system default when reset using the no variant of this command.

Mode Router Configuration

Examples To run-time configure the RIP UDP, use the following commands:

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# recv-buffer-size 23456789

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# no recv-buffer-size 23456789

Parameter Description

<8192-2147483647>Specify the RIP UDP (User Datagram Protocol) buffer size

value in bits.

613-50137-01 Rev A Command Reference for FS980M Series 683

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

REDISTRIBUTE (RIP)

redistribute (RIP)

Overview Use this command to redistribute information from other routing protocols into

RIP.

Use the no variant of this command to disable the specified redistribution. The

parameters metric and routemap may be used on this command, but have no

effect.

Syntax redistribute {connected|static|ospf} [metric <0-16>] [routemap

<routemap>]

no redistribute {connected|static|ospf} [metric] [routemap]

Default By default, the RIP metric value is set to 1.

Mode RIP Router Configuration

Example To apply the metric value 15 to static routes being redistributed into RIP, use the

commands:

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# redistribute static metric 15

Commands

default-metric (RIP)

Parameter Description

routemap Optional. Specifies route-map that controls how routes are

redistributed.

<routemap>Optional. The name of the route map.

connected Redistribute from connected routes.

static Redistribute from static routes.

ospf Redistribute from Open Shortest Path First (OSPF).

metric <0-16>Optional. Sets the value of the metric that will be applied to

routes redistributed into RIP from other protocols. If a value is not

specified, and no value is specified using the default-metric (RIP)

command, the default is one.

613-50137-01 Rev A Command Reference for FS980M Series 684

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

RESTART RIP GRACEFUL

restart rip graceful

Overview Use this command to force the RIP process to restart, and optionally set the

grace-period.

Syntax restart rip graceful [grace-period <1-65535>]

Mode Privileged Exec

Default The default RIP grace-period is 60 seconds.

Usage After this command is executed, the RIP process immediately shuts down. It

notifies the system that RIP has performed a graceful shutdown. Routes that have

been installed into the route table by RIP are preserved until the specified

grace-period expires.

When a restart rip graceful command is issued, the RIP configuration is reloaded

from the last saved configuration. Ensure you first enter the command copy

running-config startup-config.

When a master failover happens on a VCStack, the RIP grace-period will apply the

larger value of either the setting's configured value, or its default of 60 seconds.

Example To apply a restart rip graceful setting, grace-period to 100 seconds use the

following commands:

awplus# copy running-config startup-config

awplus# restart rip graceful grace-period 100

613-50137-01 Rev A Command Reference for FS980M Series 685

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

RIP RESTART GRACE-PERIOD

rip restart grace-period

Overview Use this command to change the grace period of RIP graceful restart.

Use the no variant of this command to disable this function.

Syntax rip restart grace-period <1-65535>

no rip restart grace-period <1-65535>

Mode Global Configuration

Default The default RIP grace-period is 60 seconds.

Usage Use this command to enable the Graceful Restart feature on the RIP process.

Entering this command configures a grace period for RIP.

When a master failover happens on a VCStack, the RIP grace-period will be the

longest period between the default value (60 seconds is the default RIP

grace-period) and the configured RIP grace-period value from this command. So

the configured RIP grace-period value will not be used for a VCStack master

failover if it is shorter than the default RIP grace-period value.

Example awplus# configure terminal

awplus(config)# rip restart grace-period 200

613-50137-01 Rev A Command Reference for FS980M Series 686

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

ROUTE (RIP)

route (RIP)

Overview Use this command to configure static RIP routes.

Use the no variant of this command to disable this function.

Syntax route <ip-addr/prefix-length>

no route <ip-addr/prefix-length>

Default No static RIP route is added by default.

Mode RIP Router Configuration

Usage Use this command to add a static RIP route. After adding the RIP route, the route

can be checked in the RIP routing table.

Example To create a static RIP route to IP subnet 192.168.1.0/24, use the following

commands:

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# route 192.168.1.0/24

Commands

show ip rip

clear ip rip route

Parameter Description

<ip-addr/prefix-length> The IPv4 address and prefix length.

613-50137-01 Rev A Command Reference for FS980M Series 687

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

ROUTER RIP

router rip

Overview Use this global command to enter Router Configuration mode to enable the RIP

routing process.

Use the no variant of this command to disable the RIP routing process.

Syntax router rip

no router rip

Mode Global Configuration

Example This command is used to begin the RIP routing process:

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# version 1

awplus(config-router)# network 10.10.10.0/24

awplus(config-router)# network 10.10.11.0/24

awplus(config-router)# neighbor 10.10.10.10

Commands

network (RIP)

version (RIP)

613-50137-01 Rev A Command Reference for FS980M Series 688

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

SEND-LIFETIME

send-lifetime

Overview Use this command to specify the time period during which the authentication key

on a key chain can be sent.

Syntax send-lifetime <start-date> {<end-date>|

duration <seconds>|infinite}

no send-lifetime

Mode Keychain-key Configuration

Example The following example shows the setting of send-lifetime for key 1 on the key

chain named “mychain”.

awplus# configure terminal

awplus(config)# key chain mychain

awplus(config-keychain)# key 1

awplus(config-keychain-key)# send-lifetime 03:03:01 Jan 3 2016

04:04:02 Dec 6 2016

Parameter Description

<start-date> Specifies the start time and date in the format: 

<hh:mm:ss> <day> <month> <year> or 

<hh:mm:ss> <month> <day> <year>, where:

<hh:mm:ss> The time of the day, in hours, minutes and

seconds

<day> <1-31> The day of the month

<month> The month of the year (the first three letters of

the month, for example, Jan)

<year> <1993-2035> The year

<end-date> Specifies the end time and date in the format: 

<hh:mm:ss> <day> <month> <year> or 

<hh:mm:ss> <month> <day> <year>, where:

<hh:mm:ss> The time of the day, in hours, minutes and

seconds

<day> <1-31> The day of the month

<month> The month of the year (the first three letters of

the month, for example, Jan)

<year> <1993-2035> The year

<seconds> <1-2147483646> Duration of the key in seconds.

infinite Never expires.

613-50137-01 Rev A Command Reference for FS980M Series 689

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

SEND-LIFETIME

Commands

key

key-string

key chain

accept-lifetime

613-50137-01 Rev A Command Reference for FS980M Series 690

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

SHOW DEBUGGING RIP

show debugging rip

Overview Use this command to display the RIP debugging status for these debugging

options: nsm debugging, RIP event debugging, RIP packet debugging and RIP nsm

debugging.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show debugging rip

Mode User Exec and Privileged Exec

Usage Use this command to display the debug status of RIP.

Example awplus# show debugging rip

613-50137-01 Rev A Command Reference for FS980M Series 691

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

SHOW IP PROTOCOLS RIP

show ip protocols rip

Overview Use this command to display RIP process parameters and statistics.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ip protocols rip

Mode User Exec and Privileged Exec

Example awplus# show ip protocols rip

Output Figure 21-1: Example output from the show ip protocols rip command

Routing Protocol is "rip" 

Sending updates every 30 seconds with +/-50%, next due in 12 

seconds 

Timeout after 180 seconds, garbage collect after 120 seconds 

Outgoing update filter list for all interface is not set 

Incoming update filter list for all interface is not set 

Default redistribution metric is 1 

Redistributing: connected static 

Default version control: send version 2, receive version 2 

Interface Send Recv Key-chain 

vlan25 2 2 

Routing for Networks: 

10.10.0.0/24 

Routing Information Sources: 

Gateway BadPackets BadRoutes Distance Last Update 

Distance: (default is 120

613-50137-01 Rev A Command Reference for FS980M Series 692

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

SHOW IP RIP

show ip rip

Overview Use this command to show RIP routes.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ip rip

Mode User Exec and Privileged Exec

Example awplus# show ip rip

Output Figure 21-2: Example output from the show ip rip command

Commands

route (RIP)

network (RIP)

clear ip rip route

awplus#show ip rip

Codes: R - RIP, Rc - RIP connected, Rs - RIP static

C - Connected, S - Static, O - OSPFNetwork Next Hop

Metric From If Time

C 10.0.1.0/24 1 vlan20

S 10.10.10.0/24 1 vlan20

C 10.10.11.0/24 1 vlan20

S 192.168.101.0/24 1 vlan20

R 192.192.192.0/24 1 --

613-50137-01 Rev A Command Reference for FS980M Series 693

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

SHOW IP RIP DATABASE

show ip rip database

Overview Use this command to display information about the RIP database.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ip rip database [full]

Mode User Exec and Privileged Exec

Example awplus# show ip rip database

awplus# show ip rip database full

Commands

show ip rip

Parameter Description

full Specify the full RIP database including sub-optimal RIP routes.

613-50137-01 Rev A Command Reference for FS980M Series 694

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

SHOW IP RIP INTERFACE

show ip rip interface

Overview Use this command to display information about the RIP interfaces. You can specify

an interface name to display information about a specific interface.

Syntax show ip rip interface [<interface>]

Mode User Exec and Privileged Exec

Example awplus# show ip rip interface

Parameter Description

<interface>The interface to display information about. For instance: vlan2.

613-50137-01 Rev A Command Reference for FS980M Series 695

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

TIMERS (RIP)

timers (RIP)

Overview Use this command to adjust routing network timers.

Use the no variant of this command to restore the defaults.

Syntax timers basic <update> <timeout> <garbage>

no timers basic

Default Enabled

Mode RIP Router Configuration

Usage This command adjusts the RIP timing parameters.

The update timer is the time between sending out updates, that contain the

complete routing table, to every neighboring router.

If an update for a given route has not been seen for the time specified by the

timeout parameter, that route is no longer valid. However, it is retained in the

routing table for a short time, with metric 16, so that neighbors are notified that the

route has been dropped.

When the time specified by the garbage parameter expires the metric 16 route is

finally removed from the routing table. Until the garbage time expires, the route is

included in all updates sent by the router.

All the routers in the network must have the same timers to ensure the smooth

operation of RIP throughout the network.

Examples To set the update timer to 30, the routing information timeout timer to 180, and

the routing garbage collection timer to 120, use the following command:

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# timers basic 30 180 120

Parameter Description

Specifies the period at which RIP route update packets are

transmitted. The default is 30 seconds.

Specifies the routing information timeout timer in seconds. The

default is 180 seconds. After this interval has elapsed and no updates

for a route are received, the route is declared invalid.

Specifies the routing garbage collection timer in seconds. The default

is 120 seconds.

613-50137-01 Rev A Command Reference for FS980M Series 696

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

UNDEBUG RIP

undebug rip

Overview Use this command to disable the options set for debugging information of RIP

events, packets and communication between RIP and NSM.

This command has the same effect as the no debug rip command.

Syntax undebug rip {all|events|nsm|<packet>}

Mode Privileged Exec

Example To disable the options set for debugging RIP information events, use the following

command:

awplus# undebug rip packet

Commands

debug rip

Parameter Description

all Disables all RIP debugging.

events Disables the logging of RIP events.

nsm Disables the logging of RIP and NSM communication.

<packet> packet [recv|send] [detail]

Disables the debugging of RIP packets.

recv Disables the logging of received packet information.

send Disables the logging of sent packet information.

detail Disables the logging of sent or received RIP packets.

613-50137-01 Rev A Command Reference for FS980M Series 697

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RIP COMMANDS

VERSION (RIP)

version (RIP)

Overview Use this command to specify a RIP version used globally by the router.

Use the no variant of this command to restore the default version.

Syntax version {1|2}

no version

Default Version 2

Mode RIP Router Configuration

Usage RIP can be run in version 1 or version 2 mode. Version 2 has more features than

version 1; in particular RIP version 2 supports authentication and classless routing.

Once the RIP version is set, RIP packets of that version will be received and sent on

all the RIP-enabled interfaces.

Setting the version command has no impact on receiving updates, only on

sending them. The ip rip send version command overrides the value set by the

version (RIP) command on an interface-specific basis. The ip rip receive version

command allows you to configure a specific interface to accept only packets of the

specified RIP version. The ip rip receive version command and the ip rip send

version command override the value set by this command.

Examples To specify a RIP version, use the following commands:

awplus# configure terminal

awplus(config)# router rip

awplus(config-router)# version 1

Commands

ip rip receive version

ip rip send version

show running-config

Parameter Description

1|2 Specifies the version of RIP processing.

613-50137-01 Rev A Command Reference for FS980M Series 698

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Part 4: Multicast Applications

613-50137-01 Rev A Command Reference for FS980M Series 699

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP Snooping

Commands

Introduction

Overview Devices running AlliedWare Plus use IGMP (Internet Group Management Protocol)

and MLD (Multicast Listener Discovery) to track which multicast groups their clients

belong to. This enables them to send the correct multimedia streams to the correct

destinations. IGMP is used for IPv4 multicasting, and MLD is used for IPv6

multicasting.

This chapter describes the commands to configure IGMP Snooping.

Command List •“clear ip igmp” on page 701

•“clear ip igmp group” on page 702

•“clear ip igmp interface” on page 703

•“debug igmp” on page 704

•“ip igmp flood specific-query” on page 705

•“ip igmp maximum-groups” on page 706

•“ip igmp snooping” on page 708

•“ip igmp snooping fast-leave” on page 709

•“ip igmp snooping mrouter” on page 710

•“ip igmp snooping querier” on page 711

•“ip igmp snooping report-suppression” on page 712

•“ip igmp snooping routermode” on page 713

•“ip igmp snooping tcn query solicit” on page 715

•“ip igmp static-group” on page 717

•“ip igmp trusted” on page 719

•“ip igmp version” on page 720

•“show debugging igmp” on page 721

613-50137-01 Rev A Command Reference for FS980M Series 700

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

•“show ip igmp groups” on page 722

•“show ip igmp interface” on page 724

•“show ip igmp snooping mrouter” on page 726

•“show ip igmp snooping routermode” on page 727

•“show ip igmp snooping statistics” on page 728

•“undebug igmp” on page 730

613-50137-01 Rev A Command Reference for FS980M Series 701

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

CLEAR IP IGMP

clear ip igmp

Overview Use this command to clear all IGMP group membership records on all interfaces.

Syntax clear ip igmp

Mode Privileged Exec

Example awplus# clear ip igmp

Commands

clear ip igmp group

clear ip igmp interface

show ip igmp interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 702

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

CLEAR IP IGMP GROUP

clear ip igmp group

Overview Use this command to clear IGMP group membership records for a specific group

on either all interfaces, a single interface, or for a range of interfaces.

Syntax clear ip igmp group *

clear ip igmp group <ip-address> <interface>

Mode Privileged Exec

Usage This command applies to groups learned by IGMP Snooping.

In addition to the group, an interface can be specified. Specifying this will mean

that only entries with the group learned on the interface will be deleted.

Examples To delete all group records, use the command:

awplus# clear ip igmp group *

To delete records for 224.1.1.1 on vlan1, use the command:

awplus# clear ip igmp group 224.1.1.1 vlan1

Commands

clear ip igmp

clear ip igmp interface

show ip igmp interface

show running-config

Parameter Description

*Clears all groups on all interfaces. This has the same effect as the

clear ip igmp command.

<ip-address> Specifies the group whose membership records will be cleared

from all interfaces, entered in the form A.B.C.D.

<interface>Specifies the name of the interface; all groups learned on this

interface are deleted.

613-50137-01 Rev A Command Reference for FS980M Series 703

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

CLEAR IP IGMP INTERFACE

clear ip igmp interface

Overview Use this command to clear IGMP group membership records on a particular

interface.

Syntax clear ip igmp interface <interface>

Mode Privileged Exec

Usage This command applies to interfaces configured for IGMP Snooping.

Example To delete records for vlan1, use the command:

awplus# clear ip igmp interface vlan1

Commands

clear ip igmp

clear ip igmp group

show ip igmp interface

show running-config

Parameter Description

<interface>Specifies the name of the interface. All groups learned on this

interface are deleted.

613-50137-01 Rev A Command Reference for FS980M Series 704

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

DEBUG IGMP

debug igmp

Overview Use this command to enable debugging of either all IGMP or a specific component

of IGMP.

Use the no variant of this command to disable all IGMP debugging, or debugging

of a specific component of IGMP.

Syntax debug igmp {all|decode|encode|events|fsm|tib}

no debug igmp {all|decode|encode|events|fsm|tib}

Modes Privileged Exec and Global Configuration

Example awplus# configure terminal

awplus(config)# debug igmp all

Commands

show debugging igmp

undebug igmp

Parameter Description

all Enable or disable all debug options for IGMP

decode Debug of IGMP packets that have been received

encode Debug of IGMP packets that have been sent

events Debug IGMP events

fsm Debug IGMP Finite State Machine (FSM)

tib Debug IGMP Tree Information Base (TIB)

613-50137-01 Rev A Command Reference for FS980M Series 705

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

IP IGMP FLOOD SPECIFIC-QUERY

ip igmp flood specific-query

Overview Use this command if you want IGMP to flood specific queries to all VLAN member

ports, instead of only sending the queries to multicast group member ports.

Use the no variant of this command if you want IGMP to only send the queries to

multicast group member ports.

Syntax ip igmp flood specific-query

no ip igmp flood specific-query

Default By default, specific queries are flooded to all VLAN member ports.

Mode Global Configuration

Usage In an L2 switched network running IGMP, it is considered more robust to flood all

specific queries. In most cases, the benefit of flooding specific queries to all VLAN

member ports outweighs the disadvantages.

However, sometimes this is not the case. For example, if hosts with very low CPU

capability receive specific queries for multicast groups they are not members of,

their performance may degrade unacceptably. In this situation, it is desirable for

IGMP to send specific queries to known member ports only. This minimises the

performance degradation of such hosts. In those circumstances, use this

command to turn off flooding of specific queries.

Example To cause IGMP to flood specific queries only to multicast group member ports, use

the commands:

awplus# configure terminal

awplus(config)# no ip igmp flood specific-query

Commands

show ip igmp interface

613-50137-01 Rev A Command Reference for FS980M Series 706

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

IP IGMP MAXIMUM-GROUPS

ip igmp maximum-groups

Overview Use this command to set a limit, per switch port, on the number of IGMP groups

clients can join. This stops a single client from using all the switch’s available

group-entry resources, and ensures that clients on all ports have a chance to join

IGMP groups.

Use the no variant of this command to remove the limit.

Syntax ip igmp maximum-groups <0-65535>

no ip igmp maximum-groups

Default The default is 0, which means no limit

Mode Interface mode for a switch port

Usage We recommend using this command with IGMP snooping fast leave on the

relevant VLANs. To enable fast leave, use the command:

awplus(config-if)# ip igmp snooping fast-leave

The device keeps count of the number of groups learned by each port. This counter

is incremented when group joins are received via IGMP reports. It is decremented

when:

• Group memberships time out

• Group leaves are received via leave messages or reports

Also, the port's group counter is cleared when:

• The port goes down

• You run the command clear ip igmp group *

• The port is removed from a VLAN

• The port is on a VCStack back-up member, and that member reboots or

otherwise leaves the stack.

You can see the current value of the group counter by using either of the

commands:

awplus# show ip igmp snooping statistics interface <port-list>

awplus# show ip igmp interface <port>

Parameter Description

<0-65535> The maximum number of IGMP groups clients can join on this

switch port. 0 means no limit.

613-50137-01 Rev A Command Reference for FS980M Series 707

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

IP IGMP MAXIMUM-GROUPS

Example To limit clients to 10 groups on port 1.0.1, which is in vlan1, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.1

awplus(config-if)# ip igmp maximum-groups 10

awplus(config-if)# exit

awplus(config)# interface vlan1

awplus(config-if)# ip igmp snooping fast-leave

Commands

clear ip igmp group

ip igmp snooping fast-leave

show ip igmp interface

show ip igmp snooping statistics

613-50137-01 Rev A Command Reference for FS980M Series 708

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

IP IGMP SNOOPING

ip igmp snooping

Overview Use this command to enable IGMP Snooping. When this command is used in the

Global Configuration mode, IGMP Snooping is enabled at the device level. When

this command is used in Interface Configuration mode, IGMP Snooping is enabled

for the specified VLANs.

Use the no variant of this command to either globally disable IGMP Snooping, or

disable IGMP Snooping on a specified interface.

NOTE: IGMP snooping cannot be disabled on an interface if IGMP snooping has

already been disabled globally. IGMP snooping can be disabled on both an interface

and globally if disabled on the interface first and then disabled globally.

Syntax ip igmp snooping

no ip igmp snooping

Default By default, IGMP Snooping is enabled both globally and on all VLANs.

Mode Global Configuration and Interface Configuration for a VLAN interface.

Usage For IGMP snooping to operate on particular VLAN interfaces, it must be enabled

both globally by using this command in Global Configuration mode, and on

individual VLAN interfaces by using this command in Interface Configuration

mode (both are enabled by default.)

Both IGMP snooping and MLD snooping must be enabled globally on the device

for IGMP snooping to operate. MLD snooping is also enabled by default. To enable

it if it has been disabled, use the ipv6 mld snooping command in Global

Configuration mode.

Examples To enable IGMP Snooping on vlan2, use the commands:

awplus# configure terminal

awplus(config)# ip igmp snooping

awplus(config)# interface vlan2

awplus(config-if)# ip igmp snooping

Commands

ipv6 mld snooping

show ip igmp interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 709

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

IP IGMP SNOOPING FAST-LEAVE

ip igmp snooping fast-leave

Overview Use this command to enable IGMP Snooping fast-leave processing. Fast-leave

processing is analogous to immediate-leave processing. The IGMP

group-membership entry is removed as soon as an IGMP leave group message is

received, without sending out a group-specific query.

Use the no variant of this command to disable fast-leave processing.

Syntax ip igmp snooping fast-leave

no ip igmp snooping fast-leave

Default IGMP Snooping fast-leave processing is disabled.

Mode Interface Configuration for a VLAN interface.

Usage This IGMP Snooping command can only be configured on VLAN interfaces.

Example To enable fast-leave processing on vlan2, use the commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ip igmp snooping fast-leave

Commands

show ip igmp interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 710

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

IP IGMP SNOOPING MROUTER

ip igmp snooping mrouter

Overview Use this command to statically configure the specified port as a multicast router

port for IGMP Snooping for an interface. This command applies to interfaces

configured for IGMP Snooping.

Use the no variant of this command to remove the static configuration of the port

as a multicast router port.

Syntax ip igmp snooping mrouter interface <port>

no ip igmp snooping mrouter interface <port>

Mode Interface Configuration for a VLAN interface.

Example To configure port1.0.2 statically as a multicast router interface for vlan2, use the

commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ip igmp snooping mrouter interface port1.0.2

Commands

show ip igmp snooping mrouter

Parameter Description

<port>The port may be a device port (e.g. port1.0.4), a static channel

group (e.g. sa3), or a dynamic (LACP) channel group (e.g. po4).

613-50137-01 Rev A Command Reference for FS980M Series 711

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

IP IGMP SNOOPING QUERIER

ip igmp snooping querier

Overview Use this command to enable IGMP querier operation when no multicast routing

protocol is configured. When enabled, the IGMP Snooping querier sends out

periodic IGMP queries for all interfaces. This command applies to interfaces

configured for IGMP Snooping.

Use the no variant of this command to disable IGMP querier configuration.

Syntax ip igmp snooping querier

no ip igmp snooping querier

Mode Interface Configuration for a VLAN interface.

Usage The IGMP Snooping querier uses the 0.0.0.0 Source IP address because it only

masquerades as a proxy IGMP querier for faster network convergence.

It does not start, or automatically cease, the IGMP Querier operation if it detects

query message(s) from a multicast router.

If an IP address is assigned to a VLAN, which has IGMP querier enabled on it, then

the IGMP Snooping querier uses the VLAN’s IP address as the Source IP Address in

IGMP queries.

The IGMP Snooping Querier will not stop sending IGMP Queries if there is another

IGMP Snooping Querier in the network with a lower Source IP Address.

NOTE: Do not enable the IGMP Snooping Querier feature on a Layer 2 device when

there is an operational IGMP Querier in the network.

Example To configure vlan2 as a Snooping querier, use the commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ip igmp snooping querier

Commands

show ip igmp interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 712

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

IP IGMP SNOOPING REPORT-SUPPRESSION

ip igmp snooping report-suppression

Overview Use this command to enable report suppression for IGMP versions 1 and 2. This

command applies to interfaces configured for IGMP Snooping.

Report suppression stops reports being sent to an upstream multicast router port

when there are already downstream ports for this group on this interface.

Use the no variant of this command to disable report suppression.

Syntax ip igmp snooping report-suppression

no ip igmp snooping report-suppression

Default Report suppression does not apply to IGMPv3, and is turned on by default for

IGMPv1 and IGMPv2 reports.

Mode Interface Configuration for a VLAN interface.

Example To enable report suppression for IGMPv2 reports for vlan2, use the commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ip igmp version 2

awplus(config-if)# ip igmp snooping report-suppression

Commands

show ip igmp interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 713

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

IP IGMP SNOOPING ROUTERMODE

ip igmp snooping routermode

Overview Use this command to set the destination IP addresses as router multicast

addresses.

Use the no variant of this command to set it to the default. You can also remove a

specified IP address from a custom list of multicast addresses.

Syntax ip igmp snooping routermode

{all|default|ip|multicastrouter|address <ip-address>}

no ip igmp snooping routermode [address <ip-address>]

Default The default routermode is default (not all) and shows the following reserved

multicast addresses:

Mode Global Configuration

Parameter Description

all All reserved multicast addresses (224.0.0.x).

Packets from all possible addresses in range 224.0.0.x are

treated as coming from routers.

default Default set of reserved multicast addresses.

Packets from 224.0.0.1, 224.0.0.2, 224.0.0.4, 224.0.0.5,

224.0.0.6, 224.0.0.9, 224.0.0.13, 224.0.0.15 and 224.0.0.24

are treated as coming from routers.

ip Custom reserved multicast addresses.

Packets from custom IP address in the 224.0.0.x range are

treated as coming from routers.

multicastrouter Packets from DVMRP (224.0.0.4) and PIM (224.0.0.13)

multicast addresses are treated as coming from routers.

address

<ip-address>

Packets from the specified multicast address are treated as

coming from routers. The address must be in the 224.0.0.x

range.

Router mode.............Def



Reserved multicast address

224.0.0.1

224.0.0.2

224.0.0.4

224.0.0.5

224.0.0.6

224.0.0.9

224.0.0.13

224.0.0.15

224.0.0.24

613-50137-01 Rev A Command Reference for FS980M Series 714

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

IP IGMP SNOOPING ROUTERMODE

Examples To set ip igmp snooping routermode for all default reserved addresses enter:

awplus(config)# ip igmp snooping routermode default

To remove the multicast address 224.0.0.5 from the custom list of multicast

addresses enter:

awplus(config)# no ip igmp snooping routermode address

224.0.0.5

commands

ip igmp trusted

show ip igmp snooping routermode

613-50137-01 Rev A Command Reference for FS980M Series 715

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

IP IGMP SNOOPING TCN QUERY SOLICIT

ip igmp snooping tcn query solicit

Overview Use this command to enable IGMP (Internet Group Management Protocol)

Snooping TCN (Topology Change Notification) Query Solicitation feature. When

this command is used in the Global Configuration mode, Query Solicitation is

enabled.

Use the no variant of this command to disable IGMP Snooping TCN Query

Solicitation. When the no variant of this command is used in Interface

Configuration mode, this overrides the Global Configuration mode setting and

Query Solicitation is disabled.

Syntax ip igmp snooping tcn query solicit

no ip igmp snooping tcn query solicit

Default IGMP Snooping TCN Query Solicitation is disabled by default on the device, unless

the device is the Master Node in an EPSR ring, or is the Root Bridge in a Spanning

Tree.

When the device is the Master Node in an EPSR ring, or the device is the Root

Bridge in a Spanning Tree, then IGMP Snooping TCN Query Solicitation is enabled

by default and cannot be disabled using the Global Configuration mode

command. However, Query Solicitation can be disabled for specified interfaces

using the no variant of this command from the Interface Configuration mode.

Mode Global Configuration, and Interface Configuration for a VLAN interface.

Usage Once enabled, if the device is not an IGMP Querier, on detecting a topology

change, the device generates IGMP Query Solicit messages that are sent to all the

ports of the vlan configured for IGMP Snooping on the device.

On a device that is not the Master Node in an EPSR ring or the Root Bridge in a

Spanning Tree, Query Solicitation can be disabled using the no variant of this

command after being enabled.

If the device that detects a topology change is an IGMP Querier then the device will

generate an IGMP Query message.

Note that the no variant of this command when issued in Global Configuration

mode has no effect on a device that is the Master Node in an EPSR ring or on a

device that is a Root Bridge in a Spanning Tree. Query Solicitation is not disabled

for the device these instances. However, Query Solicitation can be disabled on a

per-vlan basis from the Interface Configuration mode.

See the following state table that shows when Query Solicit messages are sent in

these instances:

613-50137-01 Rev A Command Reference for FS980M Series 716

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

IP IGMP SNOOPING TCN QUERY SOLICIT

See the IGMP Feature Overview and Configuration Guide for introductory

information about the Query Solicitation feature.

NOTE: This command will function on the switch in the stand-alone mode, but it is not

supported when the device forms part of a VCS Stack.

Examples To enable Query Solicitation on a device, use the commands:

awplus# configure terminal

awplus(config)# ip igmp snooping tcn query solicit

To disable Query Solicitation on a device, use the commands:

awplus# configure terminal

awplus(config)# no ip igmp snooping tcn query solicit

To enable Query Solicitation for vlan2, use the commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ip igmp snooping tcn query solicit

To disable Query Solicitation for vlan2, use the commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# no ip igmp snooping tcn query solicit

Commands

show ip igmp interface

show running-config

Command

issued from

Global

Configuration

Command issued

from Interface

Configuration

Device is STP Root

Bridge or the

EPSR Master Node

IGMP Query Solicit

message sent on VLAN

No Yes Yes Yes

Yes No Yes No

Yes Yes Yes Yes

613-50137-01 Rev A Command Reference for FS980M Series 717

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

IP IGMP STATIC-GROUP

ip igmp static-group

Overview Use this command to statically configure multicast group membership entries on

a VLAN interface, or to statically forward a multicast channel out a particular port

or port range.

To statically add only a group membership, do not specify any parameters.

To statically add a (*,g) entry to forward a channel out of a port, specify only the

multicast group address and the switch port range.

To statically add an (s,g) entry to forward a channel out of a port, specify the

multicast group address, the source IP address, and the switch port range.

Use the no variant of this command to delete static group membership entries.

Syntax ip igmp static-group <ip-address> [source {<ip-source-addr>}]

[interface <port>]

no ip igmp static-group <ip-address> [source

{<ip-source-addr>}] [interface <port>]

Mode Interface Configuration for a VLAN interface.

Usage This command applies to IGMP Snooping on a VLAN interface.

Parameter Description

<ip-address> Standard IP Multicast group address, entered in the form

A.B.C.D, to be configured as a static group member.

source Optional.

<ip-source-addr> Standard IP source address, entered in the form A.B.C.D, to be

configured as a static source from where multicast packets

originate.

interface Use this parameter to specify a specific switch port or switch

port range to statically forward the multicast group out of. If

not used, static configuration is applied on all ports in the

VLAN.

<port>The port or port range to statically forward the group out of.

The port may be a switch port (e.g. port1.0.4), a static

channel group (e.g. sa2), or a dynamic (LACP) channel group

(e.g. po2).

613-50137-01 Rev A Command Reference for FS980M Series 718

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

IP IGMP STATIC-GROUP

Example The following example show how to statically add group and source records for

IGMP on vlan3:

awplus# configure terminal

awplus(config)# interface vlan3

awplus(config-if)# ip igmp

awplus(config-if)# ip igmp static-group 226.1.2.4 source

10.2.3.4

613-50137-01 Rev A Command Reference for FS980M Series 719

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

IP IGMP TRUSTED

ip igmp trusted

Overview Use this command to allow IGMP to process packets received on certain trusted

ports only.

Use the no variant of this command to stop IGMP from processing specified

packets if the packets are received on the specified ports or aggregator.

Syntax ip igmp trusted {all|query|report|routermode}

no ip igmp trusted {all|query|report|routermode}

Default By default, all ports and aggregators are trusted interfaces, so IGMP is allowed to

process all IGMP query, report, and router mode packets arriving on all interfaces.

Mode Interface mode for one or more switch ports or aggregators

Usage Because all ports are trusted by default, use this command in its no variant to stop

IGMP processing packets on ports you do not trust.

For example, you can use this command to make sure that only ports attached to

approved IGMP routers are treated as router ports.

Example To stop ports port1.0.3-port1.0.6 from being treated as router ports by IGMP, use

the commands:

awplus(config)# interface port1.0.3-port1.0.6

awplus(config-if)# no ip igmp trusted routermode

Parameter Description

all Specifies whether or not the interface is allowed to receive all

IGMP and other routermode packets

query Specifies whether or not the interface is allowed to receive IGMP

queries

report Specifies whether or not the interface is allowed to receive IGMP

membership reports

routermode Specifies whether or not the interface is allowed to receive

routermode packets

613-50137-01 Rev A Command Reference for FS980M Series 720

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

IP IGMP VERSION

ip igmp version

Overview Use this command to set the current IGMP version (IGMP version 1, 2 or 3) on an

interface.

Use the no variant of this command to return to the default version.

Syntax ip igmp version <1-3>

no ip igmp version

Default The default IGMP version is 3.

Mode Interface Configuration for a VLAN interface.

Example To set the IGMP version to 2 for vlan2, use the commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ip igmp version 2

Commands

show ip igmp interface

Parameter Description

version <1-3>IGMP protocol version number

613-50137-01 Rev A Command Reference for FS980M Series 721

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

SHOW DEBUGGING IGMP

show debugging igmp

Overview Use this command to display the IGMP debugging options set.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show debugging igmp

Mode User Exec and Privileged Exec

Example To display the IGMP debugging options set, enter the command:

awplus# show debugging igmp

Output Figure 22-1: Example output from the show debugging igmp command

Commands

debug igmp

IGMP Debugging status:

IGMP Decoder debugging is on

IGMP Encoder debugging is on

IGMP Events debugging is on

IGMP FSM debugging is on

IGMP Tree-Info-Base (TIB) debugging is on

613-50137-01 Rev A Command Reference for FS980M Series 722

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

SHOW IP IGMP GROUPS

show ip igmp groups

Overview Use this command to display the multicast groups with receivers directly

connected to the router, and learned through IGMP.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ip igmp groups [<ip-address>|<interface> detail]

Mode User Exec and Privileged Exec

Example The following command displays local-membership information for all ports in all

interfaces:

awplus# show ip igmp groups

Output Figure 22-2: Example output from the show ip igmp groups command

Parameter Description

<ip-address> Address of the multicast group, entered in the form A.B.C.D.

<interface> Interface name for which to display local information.

IGMP Connected Group Membership 

Group Address Interface Uptime Expires Last Reporter 

224.0.1.1 port1.0.1 00:00:09 00:04:17 10.10.0.82 

224.0.1.24 port1.0.2 00:00:06 00:04:14 10.10.0.84 

224.0.1.40 port1.0.3 00:00:09 00:04:15 10.10.0.91 

224.0.1.60 port1.0.3 00:00:05 00:04:15 10.10.0.7 

224.100.100.100 port1.0.1 00:00:11 00:04:13 10.10.0.91 

228.5.16.8 port1.0.3 00:00:11 00:04:16 10.10.0.91 

228.81.16.8 port1.0.6 00:00:05 00:04:15 10.10.0.91 

228.249.13.8 port1.0.3 00:00:08 00:04:17 10.10.0.91 

235.80.68.83 port1.0.5 00:00:12 00:04:15 10.10.0.40 

239.255.255.250 port1.0.3 00:00:12 00:04:15 10.10.0.228 

239.255.255.254 port1.0.4 00:00:08 00:04:13 10.10.0.84

Table 1: Parameters in the output of the show ip igmp groups command

Parameter Description

Group

Address

Address of the multicast group.

Interface Port through which the group is reachable.

Uptime The time in weeks, days, hours, minutes, and seconds that this

multicast group has been known to the device.

613-50137-01 Rev A Command Reference for FS980M Series 723

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

SHOW IP IGMP GROUPS

Expires Time (in hours, minutes, and seconds) until the entry expires.

Last

Reporter

Last host to report being a member of the multicast group.

Table 1: Parameters in the output of the show ip igmp groups command (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 724

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

SHOW IP IGMP INTERFACE

show ip igmp interface

Overview Use this command to display the state of IGMP Snooping for a specified VLAN, or

all VLANs. IGMP is shown as Active or Disabled in the show output. You can also

display the number of groups a switch port belongs to.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ip igmp interface [<interface>]

Mode User Exec and Privileged Exec

Output The following output shows IGMP interface status for vlan2 with IGMP Snooping

enabled:

The following output shows IGMP interface status for vlan2 with IGMP Snooping

disabled:

Parameter Description

<interface>The name of the interface.

If you specify a switch port number, the output displays the number

of groups the port belongs to, and the port’s group membership

limit, if a limit has been set (with the command ip igmp

maximum-groups).

awplus#show ip igmp interface vlan2

Interface vlan2 (Index 202)

IGMP Disabled, Inactive, Version 3 (default)

IGMP interface has 0 group-record states

IGMP activity: 0 joins, 0 leaves

IGMP robustness variable is 2

IGMP last member query count is 2

IGMP query interval is 125 seconds

IGMP query holdtime is 500 milliseconds

IGMP querier timeout is 255 seconds

IGMP max query response time is 10 seconds

Last member query response interval is 1000 milliseconds

Group Membership interval is 260 seconds

Strict IGMPv3 ToS checking is disabled on this interface

Source Address checking is enabled

IGMP Snooping is globally enabled

IGMP Snooping query solicitation is globally disabled

Num. query-solicit packets: 57 sent, 0 recvd

IGMP Snooping is enabled on this interface

IGMP Snooping fast-leave is not enabled

IGMP Snooping querier is not enabled

IGMP Snooping report suppression is enabled

613-50137-01 Rev A Command Reference for FS980M Series 725

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

SHOW IP IGMP INTERFACE

The following output displays membership information for port1.0.1:

awplus#show ip igmp interface vlan2

Interface vlan2 (Index 202)

IGMP Disabled, Inactive, Version 3 (default)

IGMP interface has 0 group-record states

IGMP activity: 0 joins, 0 leaves

IGMP robustness variable is 2

IGMP last member query count is 2

IGMP query interval is 125 seconds

IGMP query holdtime is 500 milliseconds

IGMP querier timeout is 255 seconds

IGMP max query response time is 10 seconds

Last member query response interval is 1000 milliseconds

Group Membership interval is 260 seconds

Strict IGMPv3 ToS checking is disabled on this interface

Source Address checking is enabled

IGMP Snooping is globally enabled

IGMP Snooping query solicitation is globally disabled

Num. query-solicit packets: 57 sent, 0 recvd

IGMP Snooping is not enabled on this interface

IGMP Snooping fast-leave is not enabled

IGMP Snooping querier is not enabled

IGMP Snooping report suppression is enabled

awplus#show ip igmp interface port1.0.1

IGMP information for port1.0.1

Maximum groups limit set: 10

Number of groups port belongs to: 0

613-50137-01 Rev A Command Reference for FS980M Series 726

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

SHOW IP IGMP SNOOPING MROUTER

show ip igmp snooping mrouter

Overview Use this command to display the multicast router ports, both static and dynamic,

in a VLAN.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ip igmp snooping mrouter [interface <interface>]

Mode User Exec and Privileged Exec

Example To show all multicast router interfaces, use the command:

awplus# show ip igmp snooping mrouter

To show the multicast router interfaces in vlan1, use the command:

awplus# show ip igmp snooping mrouter interface vlan1

Output Figure 22-3: Example output from the show ip igmp snooping mrouter

command

Figure 22-4: Example output from the show ip igmp snooping mrouter interface

vlan1 command

Commands

ip igmp snooping mrouter

Parameter Description

interface A specific interface.

<interface>The name of the VLAN interface.

613-50137-01 Rev A Command Reference for FS980M Series 727

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

SHOW IP IGMP SNOOPING ROUTERMODE

show ip igmp snooping routermode

Overview Use this command to display the current routermode and the list of IP addresses

set as router multicast addresses from the ip igmp snooping routermode

command.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ip igmp snooping routermode

Mode User Exec and Privileged Exec

Example To show the routermode and the list of router multicast addresses, use the

command:

awplus# show ip igmp snooping routermode

Output Figure 22-5: Example output from the show ip igmp snooping router mode

command

Commands

ip igmp snooping routermode

awplus#show ip igmp snooping routermode

Router mode.............Def

Reserved multicast address



224.0.0.1

224.0.0.2

224.0.0.4

224.0.0.5

224.0.0.6

224.0.0.9

224.0.0.13

224.0.0.15

224.0.0.24

613-50137-01 Rev A Command Reference for FS980M Series 728

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

SHOW IP IGMP SNOOPING STATISTICS

show ip igmp snooping statistics

Overview Use this command to display IGMP Snooping statistics data.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ip igmp snooping statistics interface <interface-range>

[group [<ip-address>]]

Mode User Exec and Privileged Exec

Example To display IGMP statistical information for vlan1 and vlan2, use the command:

awplus# show ip igmp snooping statistics interface vlan1-vlan2

Output Figure 22-6: Example output from the show ip igmp snooping statistics

command for VLANs

Parameter Description

<ip-address> Optionally specify the address of the multicast group, entered in

the form A.B.C.D.

<interface> Specify the name of the interface or interface range. If you

specify a port number, the output displays the number of

groups the port belongs to, and the port’s group membership

limit, if a limit has been set (with the command ip igmp

maximum-groups)

awplus#show ip igmp interface vlan1-vlan2

IGMP Snooping statistics for vlan1

Interface: port1.0.3

Group: 224.1.1.1

Uptime: 00:00:09

Group mode: Exclude (Expires: 00:04:10)

Last reporter: 10.4.4.5

Source list is empty

IGMP Snooping statistics for vlan2

Interface: port1.0.4

Group: 224.1.1.2

Uptime: 00:00:19

Group mode: Exclude (Expires: 00:05:10)

Last reporter: 10.4.4.6

Source list is empty

613-50137-01 Rev A Command Reference for FS980M Series 729

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

SHOW IP IGMP SNOOPING STATISTICS

Figure 22-7: Example output from the show ip igmp snooping statistics

command for a switch port

awplus#show ip igmp interface port1.0.1

IGMP information for port1.0.1

Maximum groups limit set: 10

Number of groups port belongs to: 0

613-50137-01 Rev A Command Reference for FS980M Series 730

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IGMP SNOOPING COMMANDS

UNDEBUG IGMP

undebug igmp

Overview This command applies the functionality of the no debug igmp command.

613-50137-01 Rev A Command Reference for FS980M Series 731

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD Snooping

Commands

Introduction

Overview This chapter provides an alphabetical reference of configuration, clear, and show

commands related to MLD Snooping.

Command List •“clear ipv6 mld” on page 732

•“clear ipv6 mld group” on page 733

•“clear ipv6 mld interface” on page 734

•“debug mld” on page 735

•“ipv6 mld access-group” on page 736

•“ipv6 mld immediate-leave” on page 737

•“ipv6 mld limit” on page 738

•“ipv6 mld snooping” on page 740

•“ipv6 mld snooping fast-leave” on page 742

•“ipv6 mld snooping mrouter” on page 743

•“ipv6 mld snooping querier” on page 745

•“ipv6 mld snooping report-suppression” on page 746

•“ipv6 mld static-group” on page 748

•“show debugging mld” on page 750

•“show ipv6 mld groups” on page 751

•“show ipv6 mld interface” on page 752

•“show ipv6 mld snooping mrouter” on page 753

•“show ipv6 mld snooping statistics” on page 754

613-50137-01 Rev A Command Reference for FS980M Series 732

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

CLEAR IPV6 MLD

clear ipv6 mld

Overview Use this command to clear all MLD local memberships on all interfaces.

Syntax clear ipv6 mld

Mode Privileged Exec

Example awplus# clear ipv6 mld

Commands

clear ipv6 mld group

clear ipv6 mld interface

613-50137-01 Rev A Command Reference for FS980M Series 733

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

CLEAR IPV6 MLD GROUP

clear ipv6 mld group

Overview Use this command to clear MLD specific local-membership(s) on all interfaces, for

a particular group.

Syntax clear ipv6 mld group {*|<ipv6-address>}

Mode Privileged Exec

Example awplus# clear ipv6 mld group *

Commands

clear ipv6 mld

clear ipv6 mld interface

Parameter Description

*Clears all groups on all interfaces. This is an alias to the clear

ipv6 mld command.

<ipv6-address>Specify the group address for which MLD local-memberships

are to be cleared from all interfaces.

Specify the IPv6 multicast group address in the format in the

format X:X::X:X.

613-50137-01 Rev A Command Reference for FS980M Series 734

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

CLEAR IPV6 MLD INTERFACE

clear ipv6 mld interface

Overview Use this command to clear MLD interface entries.

Syntax clear ipv6 mld interface <interface>

Mode Privileged Exec

Example awplus# clear ipv6 mld interface vlan2

Commands

clear ipv6 mld

clear ipv6 mld group

Parameter Description

<interface> Specifies name of the interface; all groups learned from this interface

are deleted.

613-50137-01 Rev A Command Reference for FS980M Series 735

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

DEBUG MLD

debug mld

Overview Use this command to enable all MLD debugging modes, or a specific MLD

debugging mode.

Use the no variant of this command to disable all MLD debugging modes, or a

specific MLD debugging mode.

Syntax debug mld {all|decode|encode|events|fsm|tib}

no debug mld {all|decode|encode|events|fsm|tib}

Mode Privileged Exec and Global Configuration

Examples awplus# configure terminal

awplus(config)# debug mld all

awplus# configure terminal

awplus(config)# debug mld decode

awplus# configure terminal

awplus(config)# debug mld encode

awplus# configure terminal

awplus(config)# debug mld events

Commands

show debugging mld

Parameter Description

all Debug all MLD.

decode Debug MLD decoding.

encode Debug MLD encoding.

events Debug MLD events.

fsm Debug MLD Finite State Machine (FSM).

tib Debug MLD Tree Information Base (TIB).

613-50137-01 Rev A Command Reference for FS980M Series 736

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

IPV6 MLD ACCESS-GROUP

ipv6 mld access-group

Overview Use this command to control the multicast local-membership groups learned on

an interface.

Use the no variant of this command to disable this access control.

Syntax ipv6 mld access-group <IPv6-access-list-name>

no ipv6 mld access-group

Default No access list is configured by default.

Mode Interface Configuration for a specified VLAN interface or a range of VLAN

interfaces.

Examples In the following example, the VLAN interface vlan2 will only accept MLD joins for

groups in the range ff1e:0db8:0001::/64:

awplus# configure terminal

awplus(config)# ipv6 forwarding

awplus(config)# ipv6 multicast-routing

awplus(config)# ipv6 access-list standard group1 permit

ff1e:0db8:0001::/64

awplus(config)# interface vlan2

awplus(config-if)# ipv6 enable

awplus(config-if)# ipv6 mld access-group group1

In the following example, the VLAN interfaces vlan2-vlan4 will only accept

MLD joins for groups in the range ff1e:0db8:0001::/64:

awplus# configure terminal

awplus(config)# ipv6 forwarding

awplus(config)# ipv6 multicast-routing

awplus(config)# ipv6 access-list standard group1 permit

ff1e:0db8:0001::/64

awplus(config)# interface vlan2-vlan4

awplus(config-if)# ipv6 enable

awplus(config-if)# ipv6 mld access-group group1

Parameter Description

<IPv6-access-list-

name>

Specify a Standard or an Extended software IPv6

access-list name. See IPv6 Software Access Control List

(ACL) Commands for supported IPv6 ACLs.

613-50137-01 Rev A Command Reference for FS980M Series 737

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

IPV6 MLD IMMEDIATE-LEAVE

ipv6 mld immediate-leave

Overview Use this command to minimize the leave latency of MLD memberships.

Use the no variant of this command to disable this feature.

Syntax ipv6 mld immediate-leave group-list <IPv6-access-list-name>

no ipv6 mld immediate-leave

Default Disabled

Mode Interface Configuration for a specified VLAN interface or a range of VLAN

interfaces.

Example The following example shows how to enable the immediate-leave feature on an

interface for a specific range of multicast groups. In this example, the router

assumes that the group access-list consists of groups that have only one node

membership at a time per interface:

awplus# configure terminal

awplus(config)# ipv6 forwarding

awplus(config)# ipv6 multicast-routing

awplus(config)# interface vlan2

awplus(config-if)# ipv6 enable

awplus(config-if)# ipv6 mld immediate-leave v6grp

awplus(config-if)# exit

Parameter Description

<IPv6-access-

list-name>

Specify a Standard or an Extended software IPv6 access-list

name that defines multicast groups in which the

immediate leave feature is enabled.

See IPv6 Software Access Control List (ACL) Commands for

supported IPv6 ACLs.

613-50137-01 Rev A Command Reference for FS980M Series 738

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

IPV6 MLD LIMIT

ipv6 mld limit

Overview Use this command to configure a limit on the maximum number of group

memberships that may be learned. The limit may be set for the device as a whole,

or for a specific interface.

Once the specified group membership limit is reached, all further

local-memberships will be ignored.

Optionally, an exception access-list can be configured to specify the

group-address(es) that are exempted from being subject to the limit.

Use the no variant of this command to unset the limit and any specified exception

access-list.

Syntax ipv6 mld limit <limitvalue> [except <IPv6-access-list-name>]

no ipv6 mld limit

Default The default limit, which is reset by the no variant of this command, is the same as

maximum number of group membership entries that can be learned with the ipv6

mld limit command.

The default limit of group membership entries that can be learned is 512 entries.

Mode Global Configuration and Interface Configuration for a specified VLAN interface or

a range of VLAN interfaces.

Usage This command applies to interfaces configured for MLD Layer-3 multicast

protocols and learned by MLD Snooping.

Examples The following example configures an MLD limit of 100 group-memberships across

all VLAN interfaces on which MLD is enabled, and excludes groups in the range

ff1e:0db8:0001::/64 from this limitation:

awplus# configure terminal

awplus(config)# ipv6 forwarding

awplus(config)# ipv6 multicast-routing

awplus(config)# ipv6 access-list standard v6grp permit

ff1e:0db8:0001::/64

awplus(config)# ipv6 mld limit 100 except v6grp

Parameter Description

<limitvalue><2-512> Maximum number of group membership states.

<IPv6-access-list-

name>

Specify a Standard or an Extended software IPv6 access-list

name that defines multicast groups, which are exempted

from being subject to the configured limit.

See IPv6 Software Access Control List (ACL) Commands for

supported IPv6 ACLs.

613-50137-01 Rev A Command Reference for FS980M Series 739

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

IPV6 MLD LIMIT

The following example configures an MLD limit of 100 group-membership states

on the VLAN interface vlan2:

awplus# configure terminal

awplus(config)# ipv6 forwarding

awplus(config)# ipv6 multicast-routing

awplus(config)# interface vlan2

awplus(config-if)# ipv6 enable

awplus(config-if)# ipv6 mld limit 100

The following example configures an MLD limit of 100 group-membership states

on the VLAN interfaces vlan2-vlan4:

awplus# configure terminal

awplus(config)# ipv6 forwarding

awplus(config)# ipv6 multicast-routing

awplus(config)# interface vlan2-vlan4

awplus(config-if)# ipv6 enable

awplus(config-if)# ipv6 mld limit 100

Commands

ipv6 mld immediate-leave

show ipv6 mld groups

613-50137-01 Rev A Command Reference for FS980M Series 740

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

IPV6 MLD SNOOPING

ipv6 mld snooping

Overview Use this command to enable MLD Snooping. When this command is issued in the

Global Configuration mode, MLD Snooping is enabled globally for the device.

When this command is issued in Interface mode for a VLAN then MLD Snooping is

enabled for the specified VLAN. Note that MLD Snooping is enabled on the VLAN

only if it is enabled globally and on the VLAN.

Use the no variant of this command to globally disable MLD Snooping in Global

Configuration mode, or for the specified VLAN interface in Interface mode.

NOTE: There is a 100 MLD interface limit when applying MLD commands to multiple

VLANs. Only the first 100 VLANs have the required multicast structures added to the

interfaces that allow multicast routing.

The device has a 512 MLD group limit for (*, G) and (S,G) entries.

Syntax ipv6 mld snooping

no ipv6 mld snooping

Default By default, MLD Snooping is enabled both globally and on all VLANs.

Mode Global Configuration and Interface Configuration for a specified VLAN interface or

a range of VLAN interfaces.

Usage For MLD Snooping to operate on particular VLAN interfaces, it must be enabled

both globally by using this command in Global Configuration mode, and on

individual VLAN interfaces by using this command in Interface Configuration

mode (both are enabled by default).

MLD requires memory for storing data structures, as well as the hardware tables to

implement hardware routing. As the number of ports, VLANs, static and dynamic

groups increases then more memory is consumed. You can track the memory used

for MLD with the command:

awplus# show memory pools nsm | grep MLD

Static and dynamic groups (LACP), ports and VLANs are not limited for MLD. For

VLANs, this allows you to configure MLD across more VLANs with fewer ports per

VLAN, or fewer VLANs with more ports per VLAN. For LACPs, you can configure

MLD across more LACP groups with fewer ports per LACP, or fewer LACP groups

with more ports per LACP.

Examples To configure MLD Snooping on the VLAN interface vlan2, enter the following

commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ipv6 mld snooping

613-50137-01 Rev A Command Reference for FS980M Series 741

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

IPV6 MLD SNOOPING

To configure MLD Snooping on the VLAN interfaces vlan2-vlan4, enter the

following commands:

awplus# configure terminal

awplus(config)# interface vlan2-vlan4

awplus(config-if)# ipv6 mld snooping

To disable MLD Snooping for the VLAN interface vlan2, enter the following

commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config)# no ipv6 mld snooping

To disable MLD Snooping for the VLAN interfaces vlan2-vlan4, enter the

following commands:

awplus# configure terminal

awplus(config)# interface vlan2-vlan4

awplus(config)# no ipv6 mld snooping

To configure MLD Snooping globally for the device, enter the following

commands:

awplus# configure terminal

awplus(config)# ipv6 mld snooping

To disable MLD Snooping globally for the device, enter the following commands:

awplus# configure terminal

awplus(config)# no ipv6 mld snooping

613-50137-01 Rev A Command Reference for FS980M Series 742

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

IPV6 MLD SNOOPING FAST-LEAVE

ipv6 mld snooping fast-leave

Overview Use this command to enable MLD Snooping fast-leave processing. Fast-leave

processing is analogous to immediate-leave processing; the MLD

group-membership is removed as soon as an MLD leave group message is

received, without sending out a group-specific query.

Use the no variant of this command to disable fast-leave processing.

Syntax ipv6 mld snooping fast-leave

no ipv6 mld snooping fast-leave

Default MLD Snooping fast-leave processing is disabled.

Mode Interface Configuration for a specified VLAN interface or a range of VLAN

interfaces.

Usage This MLD Snooping command can only be configured on VLAN interfaces.

Examples This example shows how to enable fast-leave processing on the VLAN interface

vlan2.

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ipv6 mld snooping fast-leave

This example shows how to enable fast-leave processing on the VLAN interface

vlan2- vlan4.

awplus# configure terminal

awplus(config)# interface vlan2-vlan4

awplus(config-if)# ipv6 mld snooping fast-leave

613-50137-01 Rev A Command Reference for FS980M Series 743

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

IPV6 MLD SNOOPING MROUTER

ipv6 mld snooping mrouter

Overview Use this command to statically configure the specified port as a Multicast Router

interface for MLD Snooping within the specified VLAN.

See detailed usage notes below to configure static multicast router ports when

using static IPv6 multicast routes with EPSR, and the destination VLAN is an EPSR

data VLAN.

Use the no variant of this command to remove the static configuration of the

interface as a Multicast Router interface.

Syntax ipv6 mld snooping mrouter interface <port>

no ipv6 mld snooping mrouter interface <port>

Mode Interface Configuration for a specified VLAN interface or a range of VLAN

interfaces.

Usage This MLD Snooping command statically configures a switch port as a Multicast

Router interface.

Note that if static IPv6 multicast routing is being used with EPSR and the

destination VLAN is an EPSR data VLAN, then multicast router (mrouter) ports must

be statically configured. This minimizes disruption for multicast traffic in the event

of ring failure or restoration.

When configuring the EPSR data VLAN, statically configure mrouter ports so that

the multicast router can be reached in either direction around the EPSR ring.

For example, if port1.0.1 and port1.0.6 are ports on an EPSR data VLAN vlan101,

which is the destination for a static IPv6 multicast route, then configure both ports

as multicast router (mrouter) ports as shown in the example commands listed

below:

Output Figure 23-1: Example ipv6 mld snooping mrouter commands when static IPv6

multicast routing is being used and the destination VLAN is an EPSR

data VLAN:

Parameter Description

<port>Specify the name of the port.

awplus>enable

awplus#configure terminal

awplus(config)#interface vlan101

awplus(config-if)#ipv6 mld snooping mrouter interface port1.0.1

awplus(config-if)#ipv6 mld snooping mrouter interface port1.0.6

613-50137-01 Rev A Command Reference for FS980M Series 744

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

IPV6 MLD SNOOPING MROUTER

Examples This example shows how to specify the next-hop interface to the multicast router

for VLAN interface vlan2:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ipv6 mld snooping mrouter interface

port1.0.5

This example shows how to specify the next-hop interface to the multicast router

for VLAN interfaces vlan2-vlan4:

awplus# configure terminal

awplus(config)# interface vlan2-vlan4

awplus(config-if)# ipv6 mld snooping mrouter interface

port1.0.5

613-50137-01 Rev A Command Reference for FS980M Series 745

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

IPV6 MLD SNOOPING QUERIER

ipv6 mld snooping querier

Overview Use this command to enable MLD querier operation on a subnet (VLAN) when no

multicast routing protocol is configured in the subnet (VLAN). When enabled, the

MLD Snooping querier sends out periodic MLD queries for all interfaces on that

VLAN.

Use the no variant of this command to disable MLD querier configuration.

Syntax ipv6 mld snooping querier

no ipv6 mld snooping querier

Mode Interface Configuration for a specified VLAN interface.

Usage This command can only be configured on a single VLAN interface - not on multiple

VLANs.

The MLD Snooping querier uses the 0.0.0.0 Source IP address because it only

masquerades as an MLD querier for faster network convergence.

The MLD Snooping querier does not start, or automatically cease, the MLD Querier

operation if it detects query message(s) from a multicast router. It restarts as an

MLD Snooping querier if no queries are seen within the other querier interval.

Example awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ipv6 mld snooping querier

613-50137-01 Rev A Command Reference for FS980M Series 746

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

IPV6 MLD SNOOPING REPORT-SUPPRESSION

ipv6 mld snooping report-suppression

Overview Use this command to enable report suppression from hosts for Multicast Listener

Discovery version 1 (MLDv1) on a VLAN in Interface Configuration mode.

Use the no variant of this command to disable report suppression on a VLAN in

Interface Configuration mode.

Syntax ipv6 mld snooping report-suppression

no ipv6 mld snooping report-suppression

Default Report suppression does not apply to MLDv2, and is turned on by default for

MLDv1 reports.

Mode Interface Configuration for a specified VLAN interface or a range of VLAN

interfaces.

Usage This MLD Snooping command can only be configured on VLAN interfaces.

MLDv1 Snooping maybe configured to suppress reports from hosts. When a

querier sends a query, only the first report for particular set of group(s) from a host

will be forwarded to the querier by the MLD Snooping device. Similar reports (to

the same set of groups) from other hosts, which would not change group

memberships in the querier, will be suppressed by the MLD Snooping device to

prevent 'flooding' of query responses.

Examples This example shows how to enable report suppression for MLD reports on VLAN

interface vlan2:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ipv6 mld snooping report-suppression

This example shows how to disable report suppression for MLD reports on VLAN

interface vlan2:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# no ipv6 mld snooping report-suppression

This example shows how to enable report suppression for MLD reports on VLAN

interfaces vlan2-vlan4:

awplus# configure terminal

awplus(config)# interface vlan2-vlan4

awplus(config-if)# ipv6 mld snooping report-suppression

613-50137-01 Rev A Command Reference for FS980M Series 747

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

IPV6 MLD SNOOPING REPORT-SUPPRESSION

This example shows how to disable report suppression for MLD reports on VLAN

interfaces vlan2-vlan4:

awplus# configure terminal

awplus(config)# interface vlan2-vlan4

awplus(config-if)# no ipv6 mld snooping report-suppression

613-50137-01 Rev A Command Reference for FS980M Series 748

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

IPV6 MLD STATIC-GROUP

ipv6 mld static-group

Overview Use this command to statically configure IPv6 group membership entries on an

interface. To statically add only a group membership, do not specify any

parameters.

Use the no variant of this command to delete static group membership entries.

Syntax ipv6 mld static-group <ipv6-group-address> [source

<ipv6-source-address>] [interface <port>]

no ipv6 mld static-group <ipv6-group-address> [source

<ipv6-source-address>] [interface <port>]

Mode Interface Configuration for a VLAN interface.

Usage This command applies to MLD Snooping on a VLAN interface to statically add

groups and/or source records.

Examples To add a static group record, use the following commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ipv6 mld static-group ff1e::10

To add a static group and source record, use the following commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ipv6 mld static-group ff1e::10 source

fe80::2fd:6cff:fe1c:b

Parameter Description

<ipv6-group-

address>

Specify a standard IPv6 Multicast group address to be

configured as a static group member.

The IPv6 address uses the format X:X::X:X.

<ipv6-source-

address>

Optional. Specify a standard IPv6 source address to be

configured as a static source from where multicast

packets originate.

The IPv6 address uses the format X:X::X:X.

<port>Optional. Physical interface. This parameter specifies a

physical port. If this parameter is used, the static

configuration is applied to just to that physical interface.

If this parameter is not used, the static configuration is

applied on all ports in the VLAN.

613-50137-01 Rev A Command Reference for FS980M Series 749

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

IPV6 MLD STATIC-GROUP

To add a static group record on a specific port on vlan2, use the following

commands:

awplus# configure terminal

awplus(config)# interface vlan2

awplus(config-if)# ipv6 mld static-group ff1e::10 interface

port1.0.4

613-50137-01 Rev A Command Reference for FS980M Series 750

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

SHOW DEBUGGING MLD

show debugging mld

Overview Use this command to display the MLD debugging modes enabled with the debug

mld command.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show debugging mld

Mode Privileged Exec

Example awplus# show debugging mld

Output

Commands

debug mld

show debugging mld 

MLD Debugging status: 

MLD Decoder debugging is on 

MLD Encoder debugging is on 

MLD Events debugging is on 

MLD FSM debugging is on 

MLD Tree-Info-Base (TIB) debugging is on 

613-50137-01 Rev A Command Reference for FS980M Series 751

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

SHOW IPV6 MLD GROUPS

show ipv6 mld groups

Overview Use this command to display the multicast groups that have receivers directly

connected to the router and learned through MLD.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ipv6 mld groups [<ipv6-address>|<interface>] [detail]

Mode User Exec and Privileged Exec

Examples The following command displays local-membership information for all interfaces:

awplus# show ipv6 mld groups

Output Figure 23-2: Example output for show ipv6 mld groups

The following command displays local-membership information for all interfaces:

awplus# show ipv6 mld groups detail

Parameter Description

<ipv6-address>Optional. Specify Address of the multicast group in format

X:X::X:X.

<interface>Optional. Specify the Interface name for which to display local

information.

awplus#show ipv6 mld groups 

MLD Connected Group Membership 

Group Address Interface Uptime Expires 

Last Reporter 

ff08::1 vlan10 (port1.0.1) 00:07:27 00:03:10 

fe80::200:1ff:fe20:b5ac

613-50137-01 Rev A Command Reference for FS980M Series 752

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

SHOW IPV6 MLD INTERFACE

show ipv6 mld interface

Overview Use this command to display the state of MLD and MLD Snooping for a specified

interface, or all interfaces.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ipv6 mld interface [<interface>]

Mode User Exec and Privileged Exec

Example The following command displays MLD interface status on all interfaces enabled for

MLD:

awplus# show ipv6 mld interface

Output

Parameter Description

<interface>Interface name.

awplus#show ipv6 mld interface



Interface vlan1 (Index 301)

MLD Enabled, Active, Querier, Version 2 (default)

Internet address is fe80::215:77ff:fec9:7468

MLD interface has 0 group-record states

MLD activity: 0 joins, 0 leaves

MLD robustness variable is 2 

MLD last member query count is 2 

MLD query interval is 125 seconds

MLD querier timeout is 255 seconds

MLD max query response time is 10 seconds

Last member query response interval is 1000 milliseconds

Group Membership interval is 260 seconds

MLD Snooping is globally enabled

MLD Snooping is enabled on this interface

MLD Snooping fast-leave is not enabled

MLD Snooping querier is enabled

MLD Snooping report suppression is enabled

613-50137-01 Rev A Command Reference for FS980M Series 753

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

SHOW IPV6 MLD SNOOPING MROUTER

show ipv6 mld snooping mrouter

Overview Use this command to display the multicast router interfaces, both configured and

learned, in a VLAN. If you do not specify a VLAN interface then all the VLAN

interfaces are displayed.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ipv6 mld snooping mrouter [<interface>]

Mode User Exec and Privileged Exec

Examples The following command displays the multicast router interfaces in vlan2:

awplus# show ipv6 mld snooping mrouter vlan2

Output

The following command displays the multicast router interfaces for all VLAN

interfaces:

awplus# show ipv6 mld snooping mrouter

Output

Parameter Description

<interface>Optional. Specify the name of the VLAN interface. Note: If you do not

specify a single VLAN interface, then all VLAN interfaces are shown.



awplus#show ipv6 mld snooping mrouter vlan2

VLAN Interface Static/Dynamic

2 port1.0.2 Dynamically Learned

2 port1.0.3 Dynamically Learned



awplus#show ipv6 mld snooping mrouter

VLAN Interface Static/Dynamic

2 port1.0.2 Dynamically Learned

2 port1.0.3 Dynamically Learned

3 port1.0.4 Statically Assigned

3 port1.0.5 Statically Assigned

613-50137-01 Rev A Command Reference for FS980M Series 754

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

MLD SNOOPING COMMANDS

SHOW IPV6 MLD SNOOPING STATISTICS

show ipv6 mld snooping statistics

Overview Use this command to display MLD Snooping statistics data.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show ipv6 mld snooping statistics interface <interface>

Mode User Exec and Privileged Exec

Example The following command displays MLDv2 statistical information for vlan1:

awplus# show ipv6 mld snooping statistics interface vlan1

Output

Parameter Description

<interface>The name of the VLAN interface.

awplus#show ipv6 mld snooping statistics interface vlan1

MLD Snooping statistics for vlan1 

Interface: port1.0.1 

Group: ff08::1 

Uptime: 00:02:18 

Group mode: Include () 

Last reporter: fe80::eecd:6dff:fe6b:4783 

Group source list: (R - Remote, M - SSM Mapping, S - Static ) 

Source Address Uptime v2 Exp Fwd Flags 

2001:db8::1 00:02:18 00:02:02 Yes R 

2001:db8::3 00:02:18 00:02:02 Yes R 



613-50137-01 Rev A Command Reference for FS980M Series 755

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Part 5: Access and Security

613-50137-01 Rev A Command Reference for FS980M Series 756

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPv4 Hardware

Access Control List

(ACL) Commands

Introduction

Overview This chapter provides an alphabetical reference of IPv4 Hardware Access Control

List (ACL) commands. It contains detailed command information and command

examples about IPv4 hardware ACLs, which you can apply directly to interfaces

using the access-group command.

To apply ACLs to an LACP channel group, apply it to all the individual switch ports

in the channel group. To apply ACLs to a static channel group, apply it to the static

channel group itself.

Most ACL command titles include information in parentheses:

• When the command title ends with words in parentheses, these words

indicate usage instead of keywords to enter into the CLI. For example, the

title access-list (numbered hardware ACL for ICMP) indicates that the

command is used to create an ACL with the syntax:

access-list <3000-3699> <action> icmp <source-ip> <dest-ip>

[icmp-type <number>] [vlan <1-4094>]

• When the command title is completely surrounded by parentheses, the title

indicates the type of ACL filter instead of keywords to enter into the CLI. For

example, the title (named hardware ACL: ICMP entry) represents a

command with the syntax:

[<sequence-number>] <action> icmp <source-ip> <dest-ip>

[icmp-type <number>] [vlan <1-4094>]

Hardware ACLs will permit access unless explicitly denied by an ACL action.

Sub-modes Many of the ACL commands operate from sub-modes that are specific to particular

ACL types. The following table shows the CLI prompts at which ACL commands are

entered.

613-50137-01 Rev A Command Reference for FS980M Series 757

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

References For descriptions of ACLs, and further information about rules when applying them,

see the ACL Feature Overview and Configuration Guide.

For more information on link aggregation see the following references:

•the Link Aggregation Feature Overview_and Configuration Guide.

•Link Aggregation Commands

Command List •“access-group” on page 759

•“access-list (numbered hardware ACL for ICMP)” on page 761

•“access-list (numbered hardware ACL for IP packets)” on page 764

Table 24-1: IPv4 Hardware Access List Commands and Prompts

Command Name Command Mode Prompt

show interface access-group Privileged Exec awplus#

show access-list (IPv4 Hardware ACLs) Privileged Exec awplus#

show interface access-group Privileged Exec awplus#

access-list (numbered hardware ACL for IP

packets)

Global Configuration awplus(config)#

access-list (numbered hardware ACL for

ICMP)

Global Configuration awplus(config)#

access-list (numbered hardware ACL for IP

protocols)

Global Configuration awplus(config)#

access-list (numbered hardware ACL for

TCP or UDP)

Global Configuration awplus(config)#

access-list (numbered hardware ACL for

MAC addresses)

Global Configuration awplus(config)#

access-list hardware (named hardware

ACL)

Global Configuration awplus(config)#

(named hardware ACL: IP packet entry) IPv4 Hardware ACL

Configuration

awplus(config-ip-hw-acl)#

(named hardware ACL: ICMP entry) IPv4 Hardware ACL

Configuration

awplus(config-ip-hw-acl)#

(named hardware ACL: IP protocol entry) IPv4 Hardware ACL

Configuration

awplus(config-ip-hw-acl)#

(named hardware ACL: TCP or UDP entry) IPv4 Hardware ACL

Configuration

awplus(config-ip-hw-acl)#

(named hardware ACL: MAC entry) IPv4 Hardware ACL

Configuration

awplus(config-ip-hw-acl)#

commit (IPv4) IPv4 Hardware ACL

Configuration

awplus(config-ip-hw-acl)#

access-group Interface Configuration awplus(config-if)#

613-50137-01 Rev A Command Reference for FS980M Series 758

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

•“access-list (numbered hardware ACL for IP protocols)” on page 767

•“access-list (numbered hardware ACL for MAC addresses)” on page 771

•“access-list (numbered hardware ACL for TCP or UDP)” on page 773

•“access-list hardware (named hardware ACL)” on page 776

•“(named hardware ACL: ICMP entry)” on page 778

•“(named hardware ACL: IP packet entry)” on page 782

•“(named hardware ACL: IP protocol entry)” on page 786

•“(named hardware ACL: MAC entry)” on page 791

•“(named hardware ACL: TCP or UDP entry)” on page 794

•“commit (IPv4)” on page 797

•“show access-list (IPv4 Hardware ACLs)” on page 798

•“show interface access-group” on page 800

613-50137-01 Rev A Command Reference for FS980M Series 759

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-GROUP

access-group

Overview This command adds or removes a hardware-based access-list to or from a switch

port interface. The number of hardware numbered and named access-lists that can

be added to a switch port interface is determined by the available memory in

hardware-based packet classification tables.

This command works in Interface Configuration mode to apply hardware

access-lists to selected switch port interfaces.

The no variant of this command removes the selected access-list from an interface.

Syntax access-group

[<3000-3699>|<4000-4699>|<hardware-access-list-name>]

no access-group

[<3000-3699>|4000-4699|<hardware-access-list-name>]

Mode Interface Configuration for a switch port interface

Default Any traffic on an interface controlled by a hardware ACL that does not explicitly

match a filter is permitted.

Usage First create an IP access-list that applies the appropriate permit/deny requirements

with the access-list (numbered hardware ACL for IP packets) command, the

access-list (numbered hardware ACL for MAC addresses) command or the

access-list hardware (named hardware ACL) command. Then use this command to

apply this hardware access- list to a specific port or port range. Note that this

command will apply the access-list only to incoming data packets.

To apply ACLs to an LACP aggregated link, apply it to all the individual switch ports

in the aggregated group. To apply ACLs to a static channel group, apply it to the

static channel group itself. An ACL can even be applied to a static aggregated link

that spans more than one switch instance (Link Aggregation Commands).

Note that you cannot apply software numbered ACLs to switch port interfaces with

the access-group command. This command will only apply hardware ACLs.

NOTE: Hardware ACLs will permit access unless explicitly denied by an ACL action.

Parameter Description

<3000-3699> Hardware IP access-list.

<4000-4699>Hardware MAC access-list.

<hardware-access-list-name>The hardware access-list name.

613-50137-01 Rev A Command Reference for FS980M Series 760

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-GROUP

Examples To add the numbered hardware access-list 3005 to switch port interface port1.0.1,

enter the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.1

awplus(config-if)# access-group 3005

To add the named hardware access-list “hw-acl” to switch port interface port1.0.2,

enter the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# access-group hw-acl

To apply an ACL to static channel group 2 containing switch port1.0.5 and

port1.0.6, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.5-1.0.6

awplus(config-if)# static-channel-group 2

awplus(config)# interface sa2

awplus(config-if)# access-group 3000

Commands

access-list hardware (named hardware ACL)

access-list (numbered hardware ACL for IP packets)

access-list (numbered hardware ACL for MAC addresses)

show interface access-group

613-50137-01 Rev A Command Reference for FS980M Series 761

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (NUMBERED HARDWARE ACL FOR ICMP)

access-list (numbered hardware ACL for

ICMP)

Overview This command creates an access-list for use with hardware classification. The

access-list will match on ICMP packets that have the specified source and

destination IP addresses and, optionally, ICMP type. You can use the value any

instead of source or destination address if an address does not matter.

Once you have configured the ACL, you can use the access-group or the match

access-group command to apply this ACL to a port or QoS class-map.

The optional vlan parameter can be used to match tagged (802.1q) packets.

The no variant of this command removes the previously specified access-list.

Syntax access-list <3000-3699> <action> icmp <source-ip> <dest-ip>

[icmp-type <number>] [vlan <1-4094>]

no access-list <3000-3699>

Parameter Description

<3000-3699>An ID number for this hardware IP access-list.

<action> The action that the switch will take on matching packets:

deny Reject packets that match the source

and destination filtering specified

with this command.

permit Permit packets that match the source

and destination filtering specified

with this command.

send-to-cpu Send matching packets to the CPU.

icmp Match against ICMP packets

<source-ip> The source addresses to match against. You can specify a single

host, a subnet, or all source addresses. The following are the valid

formats for specifying the source:

any Match any source IP address.

host <ip-addr> Match a single source host with the

IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/<prefix>Match any source IP address within

the specified subnet. Specify the

subnet by entering the IPv4 address,

then a forward slash, then the prefix

length.

613-50137-01 Rev A Command Reference for FS980M Series 762

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (NUMBERED HARDWARE ACL FOR ICMP)

<ip-addr>

<reverse-mask>

Match any source IP address within

the specified subnet. Specify the

subnet by entering a reverse mask in

dotted decimal format. For example,

entering “192.168.1.1 0.0.0.255” is the

same as entering 192.168.1.1/24.

<dest-ip>The destination addresses to match against. You can specify a

single host, a subnet, or all destination addresses. The following

are the valid formats for specifying the destination:

any Match any destination IP address.

host <ip-addr> Match a single destination host with

the IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/<prefix>Match any destination IP address

within the specified subnet. Specify

the subnet by entering the IPv4

address, then a forward slash, then

the prefix length.

<ip-addr>

<reverse-mask>

Match any destination IP address

within the specified subnet. Specify

the subnet by entering a reverse

mask in dotted decimal format. For

example, entering “192.168.1.1

0.0.0.255” is the same as entering

192.168.1.1/24.

icmp-type

The type of ICMP message to match against, as defined in RFC792

and RFC950. Values include:

0Echo replies.

3Destination unreachable messages.

4Source quench messages.

5Redirect (change route) messages.

8Echo requests.

11 Time exceeded messages.

12 Parameter problem messages.

13 Timestamp requests.

14 Timestamp replies.

15 Information requests.

16 Information replies.

17 Address mask requests.

18 Address mask replies.

vlan <1-4094> The VLAN to match against. The ACL will match against the

specified ID in the packet’s VLAN tag.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 763

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (NUMBERED HARDWARE ACL FOR ICMP)

Mode Global Configuration

Default On an interface controlled by a hardware ACL, any traffic that does not explicitly

match a filter is permitted.

Usage This command creates an ACL for use with hardware classification. Once you have

configured the ACL, use the access-group or the match access-group command to

apply this ACL to a port or QoS class-map.

ACLs numbered in the range 3000-3699 match on packets that have the specified

source and destination IP addresses.

ICMP ACLs will match any ICMP packet that has the specified source and

destination IP addresses and ICMP type. The ICMP type is an optional parameter.

You can use ACLs to redirect packets, by sending them to the CPU. Use such ACLs

with caution. They could prevent control packets from reaching the correct

destination, such as EPSR healthcheck messages and VCStack messages.

Hardware ACLs will permit access unless explicitly denied by an ACL action.

Examples To create an access-list that will permit ICMP packets with a source address of

192.168.1.0/24 with any destination address and an ICMP type of 5 enter the

following commands:

awplus# configure terminal

awplus(config)# access-list 3000 permit icmp 192.168.1.0/24 any

icmp-type 5

To destroy the access-list with an access-list identity of 3000 enter the following

commands:

awplus# configure terminal

awplus(config)# no access-list 3000

Commands

access-group

match access-group

show running-config

show access-list (IPv4 Hardware ACLs)

613-50137-01 Rev A Command Reference for FS980M Series 764

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (NUMBERED HARDWARE ACL FOR IP PACKETS)

access-list (numbered hardware ACL for IP

packets)

Overview This command creates an access-list for use with hardware classification. The

access-list will match on packets that have the specified source and destination IP

addresses. You can use the value any instead of source or destination address if an

address does not matter.

Once you have configured the ACL, you can use the access-group or the match

access-group command to apply this ACL to a port or QoS class-map.

The optional vlan parameter can be used to match tagged (802.1q) packets.

The no variant of this command removes the previously specified IP hardware

access-list.

Syntax access-list <3000-3699> <action> ip <source-ip> <dest-ip> [vlan

<1-4094>]

no access-list <3000-3699>

Table 24-2: IP and ICMP parameters in access-list (hardware IP numbered)

Parameter Description

<3000-3699>An ID number for this hardware IP access-list.

<action> The action that the switch will take on matching packets:

deny Reject packets that match the

source and destination filtering

specified with this command.

permit Permit packets that match the

source and destination filtering

specified with this command.

send-to-cpu Send matching packets to the CPU.

ip Match against IP packets

<source-ip> The source addresses to match against. You can specify a single

host, a subnet, or all source addresses. The following are the valid

formats for specifying the source:

any Match any source IP address.

host <ip-addr> Match a single source host with the

IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/<prefix>Match any source IP address within

the specified subnet. Specify the

subnet by entering the IPv4 address,

then a forward slash, then the prefix

length.

613-50137-01 Rev A Command Reference for FS980M Series 765

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (NUMBERED HARDWARE ACL FOR IP PACKETS)

Mode Global Configuration

Default On an interface controlled by a hardware ACL, any traffic that does not explicitly

match a filter is permitted.

Usage This command creates an ACL for use with hardware classification. Once you have

configured the ACL, use the access-group or the match access-group command to

apply this ACL to a port or QoS class-map.

ACLs numbered in the range 3000-3699 match on packets that have the specified

source and destination IP addresses.

You can use ACLs to redirect packets, by sending them to the CPU. Use such ACLs

with caution. They could prevent control packets from reaching the correct

destination, such as EPSR healthcheck messages and VCStack messages.

Hardware ACLs will permit access unless explicitly denied by an ACL action.

<ip-addr>

<reverse-mask>

Match any source IP address within

the specified subnet. Specify the

subnet by entering a reverse mask in

dotted decimal format. For example,

entering “192.168.1.1 0.0.0.255” is

the same as entering 192.168.1.1/24.

<dest-ip>The destination addresses to match against. You can specify a

single host, a subnet, or all destination addresses. The following

are the valid formats for specifying the destination:

any Match any destination IP address.

host <ip-addr> Match a single destination host with

the IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/<prefix>Match any destination IP address

within the specified subnet. Specify

the subnet by entering the IPv4

address, then a forward slash, then

the prefix length.

<ip-addr>

<reverse-mask>

Match any destination IP address

within the specified subnet. Specify

the subnet by entering a reverse

mask in dotted decimal format. For

example, entering “192.168.1.1

0.0.0.255” is the same as entering

192.168.1.1/24.

vlan <1-4094> The VLAN to match against. The ACL will match against the

specified ID in the packet’s VLAN tag.

Table 24-2: IP and ICMP parameters in access-list (hardware IP numbered)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 766

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (NUMBERED HARDWARE ACL FOR IP PACKETS)

Examples To create an access-list that will permit IP packets with a source address of

192.168.1.1 and any destination address, enter the commands:

awplus# configure terminal

awplus(config)# access-list 3000 permit ip 192.168.1.1/32 any

To destroy the access-list with an access-list identity of 3000 enter the following

commands:

awplus# configure terminal

awplus(config)# no access-list 3000

Commands

access-group

match access-group

show running-config

show access-list (IPv4 Hardware ACLs)

613-50137-01 Rev A Command Reference for FS980M Series 767

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (NUMBERED HARDWARE ACL FOR IP PROTOCOLS)

access-list (numbered hardware ACL for IP

protocols)

Overview This command creates an access-list for use with hardware classification. The

access-list will match on packets that have the specified source and destination IP

addresses and IP protocol number. You can use the value any instead of source or

destination address if an address does not matter.

Once you have configured the ACL, you can use the access-group or the match

access-group command to apply this ACL to a port or QoS class-map.

The optional vlan parameter can be used to match tagged (802.1q) packets.

The no variant of this command removes the previously specified IP hardware

access-list.

Syntax access-list <3000-3699> <action> proto <1-255> <source-ip>

<dest-ip> [vlan <1-4094>]

no access-list <3000-3699>

Table 24-3: Parameters in access-list (hardware IP numbered)

Parameter Description

<3000-3699>An ID number for this hardware IP access-list.

<action> The action that the switch will take on matching packets:

deny Reject packets that match the source

and destination filtering specified

with this command.

permit Permit packets that match the source

and destination filtering specified

with this command.

send-to-cpu Send matching packets to the CPU.

proto <1-255>The IP protocol number to match against, as defined by IANA

(Internet Assigned Numbers Authority

www.iana.org/assignments/protocol-numbers)

See below for a list of IP protocol numbers and their descriptions.

<source-ip> The source addresses to match against. You can specify a single

host, a subnet, or all source addresses. The following are the valid

formats for specifying the source:

any Match any source IP address.

host <ip-addr> Match a single source host with the

IP address given by <ip-addr> in

dotted decimal notation.

613-50137-01 Rev A Command Reference for FS980M Series 768

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (NUMBERED HARDWARE ACL FOR IP PROTOCOLS)

<ip-addr>/<prefix>Match any source IP address within

the specified subnet. Specify the

subnet by entering the IPv4 address,

then a forward slash, then the prefix

length.

<ip-addr>

<reverse-mask>

Match any source IP address within

the specified subnet. Specify the

subnet by entering a reverse mask in

dotted decimal format. For example,

entering “192.168.1.1 0.0.0.255” is

the same as entering 192.168.1.1/24.

<dest-ip>The destination addresses to match against. You can specify a

single host, a subnet, or all destination addresses. The following

are the valid formats for specifying the destination:

any Match any destination IP address.

host <ip-addr> Match a single destination host with

the IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/<prefix>Match any destination IP address

within the specified subnet. Specify

the subnet by entering the IPv4

address, then a forward slash, then

the prefix length.

<ip-addr>

<reverse-mask>

Match any destination IP address

within the specified subnet. Specify

the subnet by entering a reverse

mask in dotted decimal format. For

example, entering “192.168.1.1

0.0.0.255” is the same as entering

192.168.1.1/24.

vlan <1-4094> The VLAN to match against. The ACL will match against the

specified ID in the packet’s VLAN tag.

Table 24-4: IP protocol number and description

Protocol Number Protocol Description [RFC]

1Internet Control Message [RFC792]

2Internet Group Management [RFC1112]

3Gateway-to-Gateway [RFC823]

4IP in IP [RFC2003]

5Stream [RFC1190] [RFC1819]

6TCP (Transmission Control Protocol) [RFC793]

Table 24-3: Parameters in access-list (hardware IP numbered) (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 769

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (NUMBERED HARDWARE ACL FOR IP PROTOCOLS)

8EGP (Exterior Gateway Protocol) [RFC888]

9IGP (Interior Gateway Protocol) [IANA]

11 Network Voice Protocol [RFC741]

17 UDP (User Datagram Protocol) [RFC768]

20 Host monitoring [RFC869]

27 RDP (Reliable Data Protocol) [RFC908]

28 IRTP (Internet Reliable Transaction Protocol) [RFC938]

29 ISO-TP4 (ISO Transport Protocol Class 4) [RFC905]

30 Bulk Data Transfer Protocol [RFC969]

33 DCCP (Datagram Congestion Control Protocol) [RFC4340]

48 DSR (Dynamic Source Routing Protocol) [RFC4728]

50 ESP (Encap Security Payload) [RFC2406]

51 AH (Authentication Header) [RFC2402]

54 NARP (NBMA Address Resolution Protocol) [RFC1735]

58 ICMP for IPv6 [RFC1883]

59 No Next Header for IPv6 [RFC1883]

60 Destination Options for IPv6 [RFC1883]

88 EIGRP (Enhanced Interior Gateway Routing Protocol)

89 OSPFIGP [RFC1583]

97 Ethernet-within-IP Encapsulation / RFC3378

98 Encapsulation Header / RFC1241

108 IP Payload Compression Protocol / RFC2393

112 Virtual Router Redundancy Protocol / RFC3768

134 RSVP-E2E-IGNORE / RFC3175

135 Mobility Header / RFC3775

136 UDPLite / RFC3828

137 MPLS-in-IP / RFC4023

138 MANET Protocols / RFC-ietf-manet-iana-07.txt

139-252 Unassigned / IANA

253 Use for experimentation and testing / RFC3692

254 Use for experimentation and testing / RFC3692

255 Reserved / IANA

Table 24-4: IP protocol number and description (cont.)

Protocol Number Protocol Description [RFC]

613-50137-01 Rev A Command Reference for FS980M Series 770

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (NUMBERED HARDWARE ACL FOR IP PROTOCOLS)

Mode Global Configuration

Default On an interface controlled by a hardware ACL, any traffic that does not explicitly

match a filter is permitted.

Usage This command creates an ACL for use with hardware classification. Once you have

configured the ACL, use the access-group or the match access-group command to

apply this ACL to a port or QoS class-map.

ACLs numbered in the range 3000-3699 match on packets that have the specified

source and destination IP addresses.

You can use ACLs to redirect packets, by sending them to the CPU. Use such ACLs

with caution. They could prevent control packets from reaching the correct

destination, such as EPSR healthcheck messages and VCStack messages.

Hardware ACLs will permit access unless explicitly denied by an ACL action.

Examples To create an access-list that will deny all IGMP packets (IP protocol 2) from the

192.168.0.0 network, enter the commands:

awplus# configure terminal

awplus(config)# access-list 3000 deny proto 2 192.168.0.0/16

any

To destroy the access-list with an access-list identity of 3000 enter the following

commands:

awplus# configure terminal

awplus(config)# no access-list 3000

Commands

access-group

match access-group

show running-config

show access-list (IPv4 Hardware ACLs)

613-50137-01 Rev A Command Reference for FS980M Series 771

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (NUMBERED HARDWARE ACL FOR MAC ADDRESSES)

access-list (numbered hardware ACL for

MAC addresses)

Overview This command creates an access-list for use with hardware classification. The

access-list will match on packets that have the specified source and destination

MAC addresses. You can use the value any instead of source or destination address

if an address does not matter.

Once you have configured the ACL, you can use the access-group or the match

access-group command to apply this ACL to a port or QoS class-map.

The no variant of this command removes the specified MAC hardware filter

access-list.

Syntax access-list <4000-4699> <action> {<source-mac>|any}

{<dest-mac>|any} [vlan <1-4094>]

no access-list <4000-4699>

Parameter Description

<4000-4699>Hardware MAC access-list.

<action> The action that the switch will take on matching packets:

deny Reject packets that match the source

and destination filtering specified with

this command.

permit Permit packets that match the source

and destination filtering specified with

this command.

send-to-cpu Send matching packets to the CPU.

<source-mac> The source MAC address to match against, followed by the mask.

Enter the address in the format <HHHH.HHHH.HHHH>, where each

H is a hexadecimal number.

Enter the mask in the format <HHHH.HHHH.HHHH>, where each H

is a hexadecimal number. For a mask, each value is either 0 or F,

where FF = Ignore, and 00 = Match.

any Match against any source MAC address.

<dest-mac> The destination MAC address to match against, followed by the

mask.

Enter the address in the format <HHHH.HHHH.HHHH>, where each

H is a hexadecimal number.

Enter the mask in the format <HHHH.HHHH.HHHH>, where each H

is a hexadecimal number. For a mask, each value is either 0 or F,

where FF = Ignore, and 00 = Match.

any Match against any destination MAC address.

vlan <1-4094>Match against the specified ID in the packet’s VLAN tag.

613-50137-01 Rev A Command Reference for FS980M Series 772

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (NUMBERED HARDWARE ACL FOR MAC ADDRESSES)

Mode Global Configuration

Default On an interface controlled by a hardware ACL, any traffic that does not explicitly

match a filter is permitted.

Usage This command creates an ACL for use with hardware classification. Once you have

configured the ACL, use the access-group or the match access-group command to

apply this ACL to a port or QoS class-map.

ACLs numbered in the range 4000-4699 match on packets that have the specified

source and destination MAC addresses.

You can use ACLs to redirect packets, by sending them to the CPU. Use such ACLs

with caution. They could prevent control packets from reaching the correct

destination, such as EPSR healthcheck messages and VCStack messages.

Hardware ACLs will permit access unless explicitly denied by an ACL action.

Examples To create an access-list that will permit packets with a source MAC address of

0000.00ab.1234 and any destination address, use the commands:

awplus# configure terminal

awplus(config)# access-list 4000 permit 0000.00ab.1234

0000.0000.0000 any

To create an access-list that will permit packets if their source MAC address starts

with 0000.00ab, use the commands:

awplus# configure terminal

awplus(config)# access-list 4001 permit 0000.00ab.1234

0000.0000.FFFF any

You also need to configure the mirror port with the mirror interface command.

To destroy the access-list with an access-list identity of 4000 enter the commands:

awplus# configure terminal

awplus(config)# no access-list 4000

Commands

access-group

match access-group

show running-config

show access-list (IPv4 Hardware ACLs)

613-50137-01 Rev A Command Reference for FS980M Series 773

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (NUMBERED HARDWARE ACL FOR TCP OR UDP)

access-list (numbered hardware ACL for TCP

or UDP)

Overview This command creates an access-list for use with hardware classification. The

access-list will match on TCP or UDP packets that have the specified source and

destination IP addresses and optionally, port values. You can use the value any

instead of source or destination IP address if an address does not matter.

Once you have configured the ACL, you can use the access-group or the match

access-group command to apply this ACL to a port or QoS class-map.

You can use the optional vlan parameter to match tagged (802.1q) packets.

The no variant of this command removes the specified IP hardware access-list.

Syntax access-list <3000-3699> <action> {tcp|udp} <source-ip> [eq

<0-65535>] <dest-ip> [eq <0-65535>] [vlan <1-4094>]

no access-list <3000-3699>

Parameter Description

<3000-3699>An ID number for this hardware IP access-list.

<action> The action that the switch will take on matching packets:

deny Reject packets that match the

source and destination filtering

specified with this command.

permit Permit packets that match the

source and destination filtering

specified with this command.

send-to-cpu Send matching packets to the CPU.

tcp Match against TCP packets.

udp Match against UDP packets.

<source-ip> The source addresses to match against. You can specify a single

host, a subnet, or all source addresses. The following are the valid

formats for specifying the source:

any Match any source IP address.

host <ip-addr> Match a single source host with the

IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/<prefix>Match any source IP address within

the specified subnet. Specify the

subnet by entering the IPv4 address,

then a forward slash, then the prefix

length.

613-50137-01 Rev A Command Reference for FS980M Series 774

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (NUMBERED HARDWARE ACL FOR TCP OR UDP)

Mode Global Configuration

Default On an interface controlled by a hardware ACL, any traffic that does not explicitly

match a filter is permitted.

Usage This command creates an ACL for use with hardware classification. Once you have

configured the ACL, use the access-group or the match access-group command to

apply this ACL to a port or QoS class-map.

ACLs numbered in the range 3000-3699 match on packets that have the specified

source and destination IP addresses.

You can use ACLs to redirect packets, by sending them to the CPU. Use such ACLs

with caution. They could prevent control packets from reaching the correct

destination, such as EPSR healthcheck messages and VCStack messages.

Hardware ACLs will permit access unless explicitly denied by an ACL action.

<ip-addr>

<reverse-mask>

Match any source IP address within

the specified subnet. Specify the

subnet by entering a reverse mask in

dotted decimal format. For example,

entering “192.168.1.1 0.0.0.255” is

the same as entering 192.168.1.1/24.

<dest-ip>The destination addresses to match against. You can specify a

single host, a subnet, or all destination addresses. The following

are the valid formats for specifying the destination:

any Match any destination IP address.

host <ip-addr> Match a single destination host with

the IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/<prefix>Match any destination IP address

within the specified subnet. Specify

the subnet by entering the IPv4

address, then a forward slash, then

the prefix length.

<ip-addr>

<reverse-mask>

Match any destination IP address

within the specified subnet. Specify

the subnet by entering a reverse

mask in dotted decimal format. For

example, entering “192.168.1.1

0.0.0.255” is the same as entering

192.168.1.1/24.

eq <0-65535>Match on the specified source or destination TCP or UDP port

number.

vlan <1-4094> The VLAN to match against. The ACL will match against the

specified ID in the packet’s VLAN tag.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 775

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (NUMBERED HARDWARE ACL FOR TCP OR UDP)

Examples To create an access-list that will permit TCP packets with a destination address of

192.168.1.1, a destination port of 80, and any source address and source port, enter

the commands:

awplus# configure terminal

awplus(config)# access-list 3000 permit tcp any 192.168.1.1/32

eq 80

Commands

access-group

match access-group

show running-config

show access-list (IPv4 Hardware ACLs)

613-50137-01 Rev A Command Reference for FS980M Series 776

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST HARDWARE (NAMED HARDWARE ACL)

access-list hardware (named hardware ACL)

Overview This command creates a named hardware access-list and puts you into IPv4

Hardware ACL Configuration mode, where you can add filter entries to the ACL.

Once you have configured the ACL, you can use the access-group or the match

access-group command to apply this ACL to a port or QoS class-map.

The no variant of this command removes the specified named hardware ACL.

Syntax access-list hardware <name>

no access-list hardware <name>

Mode Global Configuration

Default Any traffic on an interface controlled by a hardware ACL that does not explicitly

match a filter is permitted.

Usage Use this command to name a hardware ACL and enter the IPv4 Hardware ACL

Configuration mode. If the named hardware ACL does not exist, it will be created

after entry. If the named hardware ACL already exists, then this command puts you

into IPv4 Hardware ACL Configuration mode for that existing ACL.

Entering this command moves you to the IPv4 Hardware ACL Configuration mode

(config-ip-hw-acl prompt), so you can enter ACL filters with sequence numbers.

From this prompt, configure the filters for the ACL. See the ACL Feature Overview

and Configuration Guide for complete examples of configured sequenced

numbered ACLs.

NOTE: Hardware ACLs will permit access unless explicitly denied by an ACL action.

Examples To create the hardware access-list named “ACL-1” and enter the IPv4 Hardware

ACL Configuration mode to specify the ACL filter entry, use the commands:

awplus# configure terminal

awplus(config)# access-list hardware ACL-1

awplus(config-ip-hw-acl)#

To remove the hardware access-list named “ACL-1”, use the commands:

awplus# configure terminal

awplus(config)# no access-list hardware ACL-1

Parameter Description

<name>Specify a name for the hardware ACL.

613-50137-01 Rev A Command Reference for FS980M Series 777

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST HARDWARE (NAMED HARDWARE ACL)

Commands

access-group

(named hardware ACL: ICMP entry)

(named hardware ACL: IP protocol entry)

(named hardware ACL: TCP or UDP entry)

(access-list standard named filter)

show access-list (IPv4 Hardware ACLs)

613-50137-01 Rev A Command Reference for FS980M Series 778

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: ICMP ENTRY)

(named hardware ACL: ICMP entry)

Overview Use this command to add a new ICMP filter entry to the current hardware

access-list. The filter will match on any ICMP packet that has the specified source

and destination IP addresses and (optionally) ICMP type. You can specify the value

any if source or destination address does not matter.

If you specify a sequence number, the switch inserts the new filter at the specified

location. Otherwise, the switch adds the new filter to the end of the access-list.

The no variant of this command removes an ICMP filter entry from the current

hardware access-list. You can specify the ICMP filter entry for removal by entering

either its sequence number (e.g. no 100), or by entering its ICMP filter profile

without specifying its sequence number (e.g. no permit icmp 192.168.1.0/24 any

icmp-type 11).

You can find the sequence number by running the show access-list (IPv4 Hardware

ACLs) command.

Hardware ACLs will permit access unless explicitly denied by an ACL action.

Syntax [<sequence-number>] <action> icmp <source-ip> <dest-ip>

[icmp-type <number>] [vlan <1-4094>]

no <sequence-number>

no <action> icmp <source-ip> <dest-ip> [icmp-type <number>]

[vlan <1-4094>]

Parameter Description

<sequence-



number>

The sequence number for the filter entry of the selected access

control list, in the range 1-65535. If you do not specify a

sequence number, the switch puts the entry at the end of the

ACL and assigns it the next available multiple of 10 as its

sequence number. .

<action> The action that the switch will take on matching packets:

deny Reject packets that match the

source and destination filtering

specified with this command.

permit Permit packets that match the

source and destination filtering

specified with this command.

send-to-cpu Send matching packets to the CPU.

icmp Match against ICMP packets

<source-ip> The source addresses to match against. You can specify a single

host, a subnet, or all source addresses. The following are the

valid formats for specifying the source:

any Match any source IP address.

613-50137-01 Rev A Command Reference for FS980M Series 779

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: ICMP ENTRY)

host <ip-addr> Match a single source host with the

IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/<prefix>Match any source IP address within

the specified subnet. Specify the

subnet by entering the IPv4

address, then a forward slash, then

the prefix length.

<ip-addr>

<reverse-mask>

Match any source IP address within

the specified subnet. Specify the

subnet by entering a reverse mask

in dotted decimal format. For

example, entering “192.168.1.1

0.0.0.255” is the same as entering

192.168.1.1/24.

<dest-ip>The destination addresses to match against. You can specify a

single host, a subnet, or all destination addresses. The following

are the valid formats for specifying the destination:

any Match any destination IP address.

host <ip-addr> Match a single destination host

with the IP address given by

<ip-addr> in dotted decimal

notation.

<ip-addr>/<prefix>Match any destination IP address

within the specified subnet.

Specify the subnet by entering the

IPv4 address, then a forward slash,

then the prefix length.

<ip-addr>

<reverse-mask>

Match any destination IP address

within the specified subnet.

Specify the subnet by entering a

reverse mask in dotted decimal

format. For example, entering

“192.168.1.1 0.0.0.255” is the same

as entering 192.168.1.1/24.

icmp-type

The type of ICMP message to match against, as defined in

RFC792 and RFC950. Values include:

0Echo replies.

3Destination unreachable

messages.

4Source quench messages.

5Redirect (change route) messages.

8Echo requests.

11 Time exceeded messages.

12 Parameter problem messages.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 780

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: ICMP ENTRY)

Mode IPv4 Hardware ACL Configuration (accessed by running the command access-list

hardware (named hardware ACL))

Default On an interface controlled by a hardware ACL, any traffic that does not explicitly

match a filter is permitted.

Usage To use this command, first run the command access-list hardware (named

hardware ACL) and enter the desired access-list name. This changes the prompt to

awplus(config-ip-hw-acl)#.

Then use this command (and the other “named hardware ACL: entry” commands)

to add filter entries. You can add multiple filter entries to an ACL. You can insert a

new filter entry into the middle of an existing list by specifying the appropriate

sequence number. If you do not specify a sequence number, the switch puts the

entry at the end of the ACL and assigns it the next available multiple of 10 as its

sequence number.

Then use the access-group or the match access-group command to apply this ACL

to a port or QoS class-map. Note that the ACL will only apply to incoming data

packets.

You can use ACLs to redirect packets, by sending them to the CPU. Use such ACLs

with caution. They could prevent control packets from reaching the correct

destination, such as EPSR healthcheck messages and VCStack messages.

Examples To add an access-list filter entry with a sequence number of 100 to the access-list

named “my-list” that will permit ICMP packets with a source address of

192.168.1.0/24, any destination address and an ICMP type of 5, use the commands:

awplus# configure terminal

awplus(config)# access-list hardware my-list

awplus(config-ip-hw-acl)# 100 permit icmp 192.168.1.0/24 any

icmp-type 5

To remove an access-list filter entry with a sequence number of 100 from the

access-list named “my-list”, use the commands:

awplus# configure terminal

awplus(config)# access-list hardware my-list

awplus(config-ip-hw-acl)# no 100

13 Timestamp requests.

14 Timestamp replies.

15 Information requests.

16 Information replies.

17 Address mask requests.

18 Address mask replies.

vlan <1-4094> The VLAN to match against. The ACL will match against the

specified ID in the packet’s VLAN tag.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 781

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: ICMP ENTRY)

Commands

access-group

access-list hardware (named hardware ACL)

match access-group

show running-config

show access-list (IPv4 Hardware ACLs)

613-50137-01 Rev A Command Reference for FS980M Series 782

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: IP PACKET ENTRY)

(named hardware ACL: IP packet entry)

Overview Use this command to add an IP packet filter entry to the current hardware

access-list. The filter will match on IP packets that have the specified IP and/or MAC

addresses. You can use the value any instead of source or destination IP or MAC

address if an address does not matter.

If you specify a sequence number, the switch inserts the new filter at the specified

location. Otherwise, the switch adds the new filter to the end of the access-list.

The no variant of this command removes a filter entry from the current hardware

access-list. You can specify the filter entry for removal by entering either its

sequence number (e.g. no 100), or by entering its filter profile without specifying

its sequence number (e.g. no deny ip 192.168.0.0/16 any).

You can find the sequence number by running the show access-list (IPv4 Hardware

ACLs) command.

Hardware ACLs will permit access unless explicitly denied by an ACL action.

Syntax [<sequence-number>] <action> ip <source-ip> <dest-ip>

[<source-mac> <dest-mac>] [vlan <1-4094>]

no <sequence-number>

no <action> ip <source-ip> <dest-ip> [<source-mac> <dest-mac>]

[vlan <1-4094>]

Parameter Description

<sequence-



number>

The sequence number for the filter entry of the selected access

control list, in the range 1-65535. If you do not specify a sequence

number, the switch puts the entry at the end of the ACL and

assigns it the next available multiple of 10 as its sequence

number. .

<action> The action that the switch will take on matching packets:

deny Reject packets that match the

source and destination filtering

specified with this command.

permit Permit packets that match the

source and destination filtering

specified with this command.

send-to-cpu Send matching packets to the CPU.

ip Match against IP packets

<source-ip> The source addresses to match against. You can specify a single

host, a subnet, or all source addresses. The following are the valid

formats for specifying the source:

any Match any source IP address.

613-50137-01 Rev A Command Reference for FS980M Series 783

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: IP PACKET ENTRY)

dhcpsnooping Match the source address learned

from the DHCP Snooping binding

database.

host <ip-addr> Match a single source host with the

IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/<prefix>Match any source IP address within

the specified subnet. Specify the

subnet by entering the IPv4 address,

then a forward slash, then the prefix

length.

<ip-addr>

<reverse-mask>

Match any source IP address within

the specified subnet. Specify the

subnet by entering a reverse mask

in dotted decimal format. For

example, entering “192.168.1.1

0.0.0.255” is the same as entering

192.168.1.1/24.

<dest-ip>The destination addresses to match against. You can specify a

single host, a subnet, or all destination addresses. The following

are the valid formats for specifying the destination:

any Match any destination IP address.

host <ip-addr> Match a single destination host with

the IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/<prefix>Match any destination IP address

within the specified subnet. Specify

the subnet by entering the IPv4

address, then a forward slash, then

the prefix length.

<ip-addr>

<reverse-mask>

Match any destination IP address

within the specified subnet. Specify

the subnet by entering a reverse

mask in dotted decimal format. For

example, entering “192.168.1.1

0.0.0.255” is the same as entering

192.168.1.1/24.

<source-mac> The source MAC address to match against. You can specify a

single MAC address, a range (through a mask), the address

learned from DHCP snooping, or any:

any Match against any source MAC

address.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 784

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: IP PACKET ENTRY)

Mode IPv4 Hardware ACL Configuration (accessed by running the command access-list

hardware (named hardware ACL))

Default On an interface controlled by a hardware ACL, any traffic that does not explicitly

match a filter is permitted.

Usage To use this command, first run the command access-list hardware (named

hardware ACL) and enter the desired access-list name. This changes the prompt to

awplus(config-ip-hw-acl)#.

Then use this command (and the other “named hardware ACL: entry” commands)

to add filter entries. You can add multiple filter entries to an ACL. You can insert a

new filter entry into the middle of an existing list by specifying the appropriate

sequence number. If you do not specify a sequence number, the switch puts the

entry at the end of the ACL and assigns it the next available multiple of 10 as its

sequence number.

<source-mac> The source MAC address to match

against, followed by the mask.

Enter the address in the format

<HHHH.HHHH.HHHH>, where each

H is a hexadecimal number.

Enter the mask in the format

<HHHH.HHHH.HHHH>, where each

H is a hexadecimal number. For a

mask, each value is either 0 or F,

where FF = Ignore, and 00 = Match.

dhcpsnooping Match the source address learned

from the DHCP Snooping binding

database.

<dest-mac> The destination MAC address to match against. You can specify a

single MAC address, a range (through a mask), or any:

any Match against any destination MAC

address.

<dest-mac> The destination MAC address to

match against, followed by the

mask.

Enter the address in the format

<HHHH.HHHH.HHHH>, where each

H is a hexadecimal number.

Enter the mask in the format

<HHHH.HHHH.HHHH>, where each

H is a hexadecimal number. For a

mask, each value is either 0 or F,

where FF = Ignore, and 00 = Match.

vlan <1-4094> The VLAN to match against. The ACL will match against the

specified ID in the packet’s VLAN tag.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 785

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: IP PACKET ENTRY)

Then use the access-group or the match access-group command to apply this ACL

to a port or QoS class-map. Note that the ACL will only apply to incoming data

packets.

You can use ACLs to redirect packets, by sending them to the CPU. Use such ACLs

with caution. They could prevent control packets from reaching the correct

destination, such as EPSR healthcheck messages and VCStack messages.

Examples To add a filter entry to the access-list named “my-list” that will permit any IP packet

with a source address of 192.168.1.1, use the commands:

awplus# configure terminal

awplus(config)# access-list hardware my-list

awplus(config-ip-hw-acl)# permit ip 192.168.1.1/32 any

To add a filter entry to the access-list named “my-list” that will permit any IP packet

with a source address of 192.168.1.1and a MAC source address of ffee.ddcc.bbaa,

use the commands:

awplus# configure terminal

awplus(config)# access-list hardware my-list

awplus(config-ip-hw-acl)# permit ip 192.168.1.1/32 any mac

ffee.ddcc.bbaa 0000.0000.0000 any

To add a filter entry to the access-list named “my-list” that will deny all IP packets

on vlan 2, use the commands:

awplus# enable

awplus(config)# configure terminal

awplus(config)# access-list hardware my-list

awplus(config-ip-hw-acl)# deny ip any any vlan 2

Commands

access-group

access-list hardware (named hardware ACL)

match access-group

show running-config

show access-list (IPv4 Hardware ACLs)

613-50137-01 Rev A Command Reference for FS980M Series 786

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: IP PROTOCOL ENTRY)

(named hardware ACL: IP protocol entry)

Overview Use this command to add an IP protocol type filter entry to the current hardware

access-list. The filter will match on IP packets that have the specified IP protocol

number, and the specified IP and/or MAC addresses. You can use the value any

instead of source or destination IP or MAC address if an address does not matter.

If you specify a sequence number, the switch inserts the new filter at the specified

location. Otherwise, the switch adds the new filter to the end of the access-list.

The no variant of this command removes a filter entry from the current hardware

access-list. You can specify the filter entry for removal by entering either its

sequence number (e.g. no 100), or by entering its filter profile without specifying

its sequence number (e.g. no deny proto 2 192.168.0.0/16 any).

You can find the sequence number by running the show access-list (IPv4 Hardware

ACLs) command.

Hardware ACLs will permit access unless explicitly denied by an ACL action.

Syntax [<sequence-number>] <action> proto <1-255> <source-ip>

<dest-ip> [<source-mac> <dest-mac>] [vlan <1-4094>]

no <sequence-number>

no <action> proto <1-255> <source-ip> <dest-ip> [<source-mac>

<dest-mac>] [vlan <1-4094>]

Table 24-5: Parameters in IP protocol ACL entries

Parameter Description

<sequence-



number>

The sequence number for the filter entry of the selected access

control list, in the range 1-65535. If you do not specify a sequence

number, the switch puts the entry at the end of the ACL and

assigns it the next available multiple of 10 as its sequence

number. .

<action> The action that the switch will take on matching packets:

deny Reject packets that match the

source and destination filtering

specified with this command.

permit Permit packets that match the

source and destination filtering

specified with this command.

send-to-cpu Send matching packets to the CPU.

proto <1-255>The IP protocol number to match against, as defined by IANA

(Internet Assigned Numbers Authority

www.iana.org/assignments/protocol-numbers)

See below for a list of IP protocol numbers and their descriptions.

<source-ip> The source addresses to match against. You can specify a single

host, a subnet, or all source addresses. The following are the valid

formats for specifying the source:

613-50137-01 Rev A Command Reference for FS980M Series 787

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: IP PROTOCOL ENTRY)

any Match any source IP address.

dhcpsnooping Match the source address learned

from the DHCP Snooping binding

database.

host <ip-addr> Match a single source host with the

IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/<prefix>Match any source IP address within

the specified subnet. Specify the

subnet by entering the IPv4

address, then a forward slash, then

the prefix length.

<ip-addr>

<reverse-mask>

Match any source IP address within

the specified subnet. Specify the

subnet by entering a reverse mask

in dotted decimal format. For

example, entering “192.168.1.1

0.0.0.255” is the same as entering

192.168.1.1/24.

<dest-ip>The destination addresses to match against. You can specify a

single host, a subnet, or all destination addresses. The following

are the valid formats for specifying the destination:

any Match any destination IP address.

host <ip-addr> Match a single destination host with

the IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/<prefix>Match any destination IP address

within the specified subnet. Specify

the subnet by entering the IPv4

address, then a forward slash, then

the prefix length.

<ip-addr>

<reverse-mask>

Match any destination IP address

within the specified subnet. Specify

the subnet by entering a reverse

mask in dotted decimal format. For

example, entering “192.168.1.1

0.0.0.255” is the same as entering

192.168.1.1/24.

<source-mac> The source MAC address to match against. You can specify a

single MAC address, a range (through a mask), the address

learned from DHCP snooping, or any:

any Match against any source MAC

address.

Table 24-5: Parameters in IP protocol ACL entries (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 788

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: IP PROTOCOL ENTRY)

<source-mac> The source MAC address to match

against, followed by the mask.

Enter the address in the format

<HHHH.HHHH.HHHH>, where each

H is a hexadecimal number.

Enter the mask in the format

<HHHH.HHHH.HHHH>, where each

H is a hexadecimal number. For a

mask, each value is either 0 or F,

where FF = Ignore, and 00 = Match.

dhcpsnooping Match the source address learned

from the DHCP Snooping binding

database.

<dest-mac> The destination MAC address to match against. You can specify a

single MAC address, a range (through a mask), or any:

any Match against any destination MAC

address.

<dest-mac> The destination MAC address to

match against, followed by the

mask.

Enter the address in the format

<HHHH.HHHH.HHHH>, where each

H is a hexadecimal number.

Enter the mask in the format

<HHHH.HHHH.HHHH>, where each

H is a hexadecimal number. For a

mask, each value is either 0 or F,

where FF = Ignore, and 00 = Match.

vlan <1-4094> The VLAN to match against. The ACL will match against the

specified ID in the packet’s VLAN tag.

Table 24-6: IP protocol number and description

Protocol Number Protocol Description [RFC]

1Internet Control Message [RFC792]

2Internet Group Management [RFC1112]

3Gateway-to-Gateway [RFC823]

4IP in IP [RFC2003]

5Stream [RFC1190] [RFC1819]

6TCP (Transmission Control Protocol) [RFC793]

8EGP (Exterior Gateway Protocol) [RFC888]

9IGP (Interior Gateway Protocol) [IANA]

Table 24-5: Parameters in IP protocol ACL entries (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 789

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: IP PROTOCOL ENTRY)

Mode IPv4 Hardware ACL Configuration (accessed by running the command access-list

hardware (named hardware ACL))

11 Network Voice Protocol [RFC741]

17 UDP (User Datagram Protocol) [RFC768]

20 Host monitoring [RFC869]

27 RDP (Reliable Data Protocol) [RFC908]

28 IRTP (Internet Reliable Transaction Protocol) [RFC938]

29 ISO-TP4 (ISO Transport Protocol Class 4) [RFC905]

30 Bulk Data Transfer Protocol [RFC969]

33 DCCP (Datagram Congestion Control Protocol)

[RFC4340]

48 DSR (Dynamic Source Routing Protocol) [RFC4728]

50 ESP (Encap Security Payload) [RFC2406]

51 AH (Authentication Header) [RFC2402]

54 NARP (NBMA Address Resolution Protocol) [RFC1735]

58 ICMP for IPv6 [RFC1883]

59 No Next Header for IPv6 [RFC1883]

60 Destination Options for IPv6 [RFC1883]

88 EIGRP (Enhanced Interior Gateway Routing Protocol)

89 OSPFIGP [RFC1583]

97 Ethernet-within-IP Encapsulation / RFC3378

98 Encapsulation Header / RFC1241

108 IP Payload Compression Protocol / RFC2393

112 Virtual Router Redundancy Protocol / RFC3768

134 RSVP-E2E-IGNORE / RFC3175

135 Mobility Header / RFC3775

136 UDPLite / RFC3828

137 MPLS-in-IP / RFC4023

138 MANET Protocols / RFC-ietf-manet-iana-07.txt

139-252 Unassigned / IANA

253 Use for experimentation and testing / RFC3692

254 Use for experimentation and testing / RFC3692

255 Reserved / IANA

Table 24-6: IP protocol number and description (cont.)

Protocol Number Protocol Description [RFC]

613-50137-01 Rev A Command Reference for FS980M Series 790

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: IP PROTOCOL ENTRY)

Default On an interface controlled by a hardware ACL, any traffic that does not explicitly

match a filter is permitted.

Usage To use this command, run the command access-list hardware (named hardware

ACL) and enter the desired access-list name. This changes the prompt to

awplus(config-ip-hw-acl)#.

Then use this command (and the other “named hardware ACL: entry” commands)

to add filter entries. You can add multiple filter entries to an ACL. You can insert a

new filter entry into the middle of an existing list by specifying the appropriate

sequence number. If you do not specify a sequence number, the switch puts the

entry at the end of the ACL and assigns it the next available multiple of 10 as its

sequence number.

Then use the access-group or the match access-group command to apply this ACL

to a port or QoS class-map. Note that the ACL will only apply to incoming data

packets.

You can use ACLs to redirect packets, by sending them to the CPU. Use such ACLs

with caution. They could prevent control packets from reaching the correct

destination, such as EPSR healthcheck messages and VCStack messages.

Examples To add a filter entry to the access-list named “my-list” that will deny all IGMP

packets (protocol 2) from the 192.168.0.0 subnet, and give it a sequence number

of 50, use the commands:

awplus# configure terminal

awplus(config)# access-list hardware my-list

awplus(config-ip-hw-acl)# 50 deny proto 2 192.168.0.0/16 any

Commands

access-group

access-list hardware (named hardware ACL)

match access-group

show running-config

show access-list (IPv4 Hardware ACLs)

613-50137-01 Rev A Command Reference for FS980M Series 791

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: MAC ENTRY)

(named hardware ACL: MAC entry)

Overview Use this command to add a MAC address filter entry to the current hardware

access-list. The access-list will match on packets that have the specified source and

destination MAC addresses. You can use the value any instead of source or

destination MAC address if an address does not matter.

If you specify a sequence number, the switch inserts the new filter at the specified

location. Otherwise, the switch adds the new filter to the end of the access-list.

The no variant of this command removes a filter entry from the current hardware

access-list. You can specify the filter entry for removal by entering either its

sequence number (e.g. no 100), or by entering its filter profile without specifying

its sequence number (e.g. no permit mac aaaa.bbbb.cccc 0000.0000.0000 any).

You can find the sequence number by running the show access-list (IPv4 Hardware

ACLs) command.

Hardware ACLs will permit access unless explicitly denied by an ACL action.

Syntax [<sequence-number>] <action> mac {<source-mac>|any}

{<dest-mac>|any} [vlan <1-4094>]

no <sequence-number>

no <action> mac {<source-mac>|any} {<dest-mac>|any} [vlan

<1-4094>]

Parameter Description

<4000-4699>Hardware MAC access-list.

<action> The action that the switch will take on matching packets:

deny Reject packets that match the source

and destination filtering specified with

this command.

permit Permit packets that match the source

and destination filtering specified with

this command.

send-to-cpu Send matching packets to the CPU.

mac Match against MAC address

<source-mac> The source MAC address to match against, followed by the mask.

Enter the address in the format <HHHH.HHHH.HHHH>, where each

H is a hexadecimal number.

Enter the mask in the format <HHHH.HHHH.HHHH>, where each H

is a hexadecimal number. For a mask, each value is either 0 or F,

where FF = Ignore, and 00 = Match.

any Match against any source MAC address.

613-50137-01 Rev A Command Reference for FS980M Series 792

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: MAC ENTRY)

Mode IPv4 Hardware ACL Configuration (accessed by running the command access-list

hardware (named hardware ACL))

Default On an interface controlled by a hardware ACL, any traffic that does not explicitly

match a filter is permitted.

Usage To use this command, first run the command access-list hardware (named

hardware ACL) and enter the desired access-list name. This changes the prompt to

awplus(config-ip-hw-acl)#.

Then use this command (and the other “named hardware ACL: entry” commands)

to add filter entries. You can add multiple filter entries to an ACL. You can insert a

new filter entry into the middle of an existing list by specifying the appropriate

sequence number. If you do not specify a sequence number, the switch puts the

entry at the end of the ACL and assigns it the next available multiple of 10 as its

sequence number.

Then use the access-group or the match access-group command to apply this ACL

to a port or QoS class-map. Note that the ACL will only apply to incoming data

packets.

You can use ACLs to redirect packets, by sending them to the CPU. Use such ACLs

with caution. They could prevent control packets from reaching the correct

destination, such as EPSR healthcheck messages and VCStack messages.

Examples To add a filter entry to the access-list named “my-list” that will permit packets with

a source MAC address of 0000.00ab.1234 and any destination MAC address, use

the commands:

awplus# configure terminal

awplus(config)# access-list hardware my-list

awplus(config-ip-hw-acl)# permit mac 0000.00ab.1234

0000.0000.0000 any

To remove a filter entry that permit packets with a source MAC address of

0000.00ab.1234 and any destination MAC address, use the commands:

awplus# configure terminal

awplus(config)# access-list hardware my-list

awplus(config-ip-hw-acl)# no permit mac 0000.00ab.1234

0000.0000.0000 any

<dest-mac> The destination MAC address to match against, followed by the

mask.

Enter the address in the format <HHHH.HHHH.HHHH>, where each

H is a hexadecimal number.

Enter the mask in the format <HHHH.HHHH.HHHH>, where each H

is a hexadecimal number. For a mask, each value is either 0 or F,

where FF = Ignore, and 00 = Match.

any Match against any destination MAC address.

vlan <1-4094>Match against the specified ID in the packet’s VLAN tag.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 793

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: MAC ENTRY)

Commands

access-group

access-list hardware (named hardware ACL)

match access-group

show running-config

show access-list (IPv4 Hardware ACLs)

613-50137-01 Rev A Command Reference for FS980M Series 794

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: TCP OR UDP ENTRY)

(named hardware ACL: TCP or UDP entry)

Overview Use this command to add a TCP or UDP filter entry to the current hardware

access-list. The access-list will match on TCP or UDP packets that have the specified

source and destination IP addresses and optionally, port values. You can use the

value any instead of source or destination IP address if an address does not matter.

If you specify a sequence number, the switch inserts the new filter at the specified

location. Otherwise, the switch adds the new filter to the end of the access-list.

The no variant of this command removes a filter entry from the current hardware

access-list. You can specify the filter entry for removal by entering either its

sequence number (e.g. no 100), or by entering its filter profile without specifying

its sequence number (e.g. no permit udp 192.168.0.0/16 any).

You can find the sequence number by running the show access-list (IPv4 Hardware

ACLs) command.

Hardware ACLs will permit access unless explicitly denied by an ACL action.

Syntax [<sequence-number>] <action> {tcp|udp} <source-ip> [eq

<0-65535>] <dest-ip> [eq <0-65535>] [vlan <1-4094>]

no <sequence-number>

no <action> {tcp|udp} <source-ip> [eq <0-65535>] <dest-ip> [eq

<0-65535>] [vlan <1-4094>]

Parameter Description

<sequence-



number>

The sequence number for the filter entry of the selected access

control list, in the range 1-65535. If you do not specify a sequence

number, the switch puts the entry at the end of the ACL and

assigns it the next available multiple of 10 as its sequence

number. .

<action> The action that the switch will take on matching packets:

deny Reject packets that match the

source and destination filtering

specified with this command.

permit Permit packets that match the

source and destination filtering

specified with this command.

send-to-cpu Send matching packets to the CPU.

tcp Match against TCP packets.

udp Match against UDP packets.

<source-ip> The source addresses to match against. You can specify a single

host, a subnet, or all source addresses. The following are the valid

formats for specifying the source:

any Match any source IP address.

613-50137-01 Rev A Command Reference for FS980M Series 795

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: TCP OR UDP ENTRY)

Mode IPv4 Hardware ACL Configuration (accessed by running the command access-list

hardware (named hardware ACL))

Default On an interface controlled by a hardware ACL, any traffic that does not explicitly

match a filter is permitted.

Usage To use this command, first run the command access-list hardware (named

hardware ACL) and enter the desired access-list name. This changes the prompt to

awplus(config-ip-hw-acl)#.

host <ip-addr> Match a single source host with the

IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/<prefix>Match any source IP address within

the specified subnet. Specify the

subnet by entering the IPv4 address,

then a forward slash, then the prefix

length.

<ip-addr>

<reverse-mask>

Match any source IP address within

the specified subnet. Specify the

subnet by entering a reverse mask

in dotted decimal format. For

example, entering “192.168.1.1

0.0.0.255” is the same as entering

192.168.1.1/24.

<dest-ip>The destination addresses to match against. You can specify a

single host, a subnet, or all destination addresses. The following

are the valid formats for specifying the destination:

any Match any destination IP address.

host <ip-addr> Match a single destination host with

the IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/<prefix>Match any destination IP address

within the specified subnet. Specify

the subnet by entering the IPv4

address, then a forward slash, then

the prefix length.

<ip-addr>

<reverse-mask>

Match any destination IP address

within the specified subnet. Specify

the subnet by entering a reverse

mask in dotted decimal format. For

example, entering “192.168.1.1

0.0.0.255” is the same as entering

192.168.1.1/24.

eq <0-65535>Match on the specified source or destination TCP or UDP port

number.

vlan <1-4094> The VLAN to match against. The ACL will match against the

specified ID in the packet’s VLAN tag.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 796

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

(NAMED HARDWARE ACL: TCP OR UDP ENTRY)

Then use this command (and the other “named hardware ACL: entry” commands)

to add filter entries. You can add multiple filter entries to an ACL. You can insert a

new filter entry into the middle of an existing list by specifying the appropriate

sequence number. If you do not specify a sequence number, the switch puts the

entry at the end of the ACL and assigns it the next available multiple of 10 as its

sequence number.

Then use the access-group or the match access-group command to apply this ACL

to a port or QoS class-map. Note that the ACL will only apply to incoming data

packets.

You can use ACLs to redirect packets, by sending them to the CPU. Use such ACLs

with caution. They could prevent control packets from reaching the correct

destination, such as EPSR healthcheck messages and VCStack messages.

Example To add a filter entry to access-list named “my-list” that will permit TCP packets with

a destination address of 192.168.1.1, a destination port of 80, from any source, use

the commands:

awplus# configure terminal

awplus(config)# access-list hardware my-list

awplus(config-ip-hw-acl)# permit tcp any 192.168.1.1/32 eq 80

Commands

access-group

access-list hardware (named hardware ACL)

match access-group

show running-config

show access-list (IPv4 Hardware ACLs)

613-50137-01 Rev A Command Reference for FS980M Series 797

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

COMMIT (IPV4)

commit (IPv4)

Overview Use this command to commit the IPv4 ACL filter configuration entered at the

console to the hardware immediately without exiting the IPv4 Hardware ACL

Configuration mode.

This command forces the associated hardware and software IPv4 ACLs to

synchronize.

Syntax commit

Mode IPv4 Hardware ACL Configuration

Usage Normally, when an IPv4 hardware ACL is edited, the new configuration state of the

IPv4 ACL is not written to hardware until you exit IPv4 Hardware ACL Configuration

mode. By entering this command you can ensure that the current state of a

hardware access-list that is being edited is written to hardware immediately.

Scripts typically do not include the exit command to exit configuration modes,

potentially leading to IPv4 ACL filters in hardware not being correctly updated.

Using this commit command in a configuration script after specifying an IPv4

hardware ACL filter ensures that it is updated in the hardware immediately.

Example To update the hardware with the IPv4 ACL filter configuration, use the command:

awplus# configure terminal

awplus(config)# access-list hardware my-hw-list

awplus(config-ip-hw-acl)# commit

Commands

access-list hardware (named hardware ACL)

613-50137-01 Rev A Command Reference for FS980M Series 798

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

SHOW ACCESS-LIST (IPV4 HARDWARE ACLS)

show access-list (IPv4 Hardware ACLs)

Overview Use this command to display the specified access-list, or all access-lists if none have

been specified. Note that only defined access-lists are displayed. An error message

is displayed for an undefined access-list.

Syntax show access-list

[<1-99>|<100-199>|<1300-1999>|<2000-2699>|<3000-3699>|<4000-44

99>|<access-list-name>]

Mode User Exec and Privileged Exec

Examples To show all access-lists configured on the switch:

awplus# show access-list

To show the access-list with an ID of 20:

awplus# show access-list 20

The following error message is displayed if you try to show an undefined

access-list.

awplus# show access-list 2

Parameter Description

<1-99>IP standard access-list.

<1300-1999>IP standard access-list (standard - expanded range).

<3000-3699>Hardware IP access-list.

<4000-4499>Hardware MAC access-list.

<access-list-name>IP named access-list.

Standard IP access list 1

deny 172.16.2.0, wildcard bits 0.0.0.255

Standard IP access list 20

deny 192.168.10.0, wildcard bits 0.0.0.255

deny 192.168.12.0, wildcard bits 0.0.0.255

Hardware IP access list 3001

permit ip 192.168.20.0 255.255.255.0 any

Hardware IP access list 3020

permit tcp any 192.0.2.0/24

awplus#show access-list 20

Standard IP access-list 20

deny 192.168.10.0, wildcard bits 0.0.0.255

deny 192.168.12.0, wildcard bits 0.0.0.255

613-50137-01 Rev A Command Reference for FS980M Series 799

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

SHOW ACCESS-LIST (IPV4 HARDWARE ACLS)

Commands

access-list (numbered hardware ACL for MAC addresses)

access-list hardware (named hardware ACL)

% Can't find access-list 2

613-50137-01 Rev A Command Reference for FS980M Series 800

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 HARDWARE ACCESS CONTROL LIST (ACL) COMMANDS

SHOW INTERFACE ACCESS-GROUP

show interface access-group

Overview Use this command to display the access groups attached to a port. If an access

group is specified, then the output only includes the ports that the specified access

group is attached to. If no access group is specified then this command displays all

access groups that are attached to the ports that are specified with <port-list>.

Note that access group is the term given for an access-list when it is applied to an

interface.

NOTE: This command will function on the switch in stand-alone mode, but is not

supported when the switch forms part of a VCStack.

Syntax show interface <port-list> access-group

[<3000-3699>|<4000-4699>]

Mode User Exec and Privileged Exec

Example To show all access-lists attached to port1.0.1, use the command:

awplus# show interface port1.0.1 access-group

Output Figure 24-1: Example output from the show interface access-group command

Commands

access-group

Parameter Description

<port-list> Specify the ports to display information. A port-list can be

either:

• a switch port (e.g. port1.0.6) a static channel group (e.g.

sa2) or a dynamic (LACP) channel group (e.g. po2)

• a continuous range of ports separated by a hyphen, e.g.

port1.0.1-1.0.6 or port1.0.1-port1.0.6 or po1-po2

• a comma-separated list of ports and port ranges, e.g.

port1.0.1,port1.0.3-1.0.6. Do not mix switch ports, static

channel groups, and LACP channel groups in the same

list.

access group Select the access group whose details you want to show.

<3000-3699> Specifies the Hardware IP access-list.

<4000-4699> Specifies the Hardware MAC access-list.

Interface port1.0.1

access-group 3000

access-group 3002

access-group 3001

613-50137-01 Rev A Command Reference for FS980M Series 801

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPv4 Software

Access Control List

(ACL) Commands

Introduction

Overview This chapter provides an alphabetical reference for the IPv4 Software Access

Control List (ACL) commands, and contains detailed command information and

command examples about IPv4 software ACLs as applied to Routing and

Multicasting, which are not applied to interfaces.

For information about ACLs, see the ACL Feature Overview and Configuration

Guide.

To apply ACLs to an LACP channel group, apply it to all the individual switch ports

in the channel group. To apply ACLs to a static channel group, apply it to the static

channel group itself. For more information on link aggregation see the following

references:

•the Link Aggregation Feature Overview_and Configuration Guide.

•Link Aggregation Commands

NOTE: Text in parenthesis in command names indicates usage not keyword entry. For

example, access-list hardware (named) indicates named IPv4 hardware ACLs

entered as access-list hardware <name> where <name> is a placeholder not

a keyword.

Parenthesis surrounding ACL filters indicates the type of ACL filter not the keyword

entry in the CLI, such as (access-list standard numbered filter) represents command

entry in the format shown in the syntax:

[<sequence-number>] {deny|permit} {<source-address>|host

<host-address>|any}

NOTE: Software ACLs will deny access unless explicitly permitted by an ACL action.

Sub-modes Many of the ACL commands operate from sub-modes that are specific to particular

ACL types. The following table shows the CLI prompts at which ACL commands are

entered.

613-50137-01 Rev A Command Reference for FS980M Series 802

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

Command List •“access-list extended (named)” on page 804

•“access-list (extended numbered)” on page 812

•“(access-list extended ICMP filter)” on page 814

•“(access-list extended IP filter)” on page 816

•“(access-list extended IP protocol filter)” on page 819

•“(access-list extended TCP UDP filter)” on page 823

•“access-list standard (named)” on page 825

•“access-list (standard numbered)” on page 827

•“(access-list standard named filter)” on page 829

•“(access-list standard numbered filter)” on page 831

•“clear ip prefix-list” on page 833

•“ip prefix-list” on page 834

•“maximum-access-list” on page 836

•“show access-list (IPv4 Software ACLs)” on page 837

Table 25-1: IPv4 Software Access List Commands and Prompts

Command Name Command Mode Prompt

show ip access-list Privileged Exec awplus#

access-group Global Configuration awplus(config)#

access-list (extended named) Global Configuration awplus(config)#

access-list (extended numbered) Global Configuration awplus(config)#

access-list (standard named) Global Configuration awplus(config)#

access-list (standard numbered) Global Configuration awplus(config)#

maximum-access-list Global Configuration awplus(config)#

(access-list extended ICMP filter) IPv4 Extended ACL

Configuration

awplus(config-ip-ext-acl)#

(access-list extended IPfilter) IPv4 Extended ACL

Configuration

awplus(config-ip-ext-acl)#

(access-list extended IP protocol filter) IPv4 Extended ACL

Configuration

awplus(config-ip-ext-acl)#

(access-list extended TCP UDP filter) IPv4 Extended ACL

Configuration

awplus(config-ip-ext-acl)#

(access-list standard named filter) IPv4 Standard ACL

Configuration

awplus(config-ip-std-acl)#

(access-list standard numbered filter) IPv4 Standard ACL

Configuration

awplus(config-ip-std-acl)#

613-50137-01 Rev A Command Reference for FS980M Series 803

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

•“show ip access-list” on page 839

•“show ip prefix-list” on page 840

•“vty access-class (numbered)” on page 841

613-50137-01 Rev A Command Reference for FS980M Series 804

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST EXTENDED (NAMED)

access-list extended (named)

Overview This command configures an extended named access-list that permits or denies

packets from specific source and destination IP addresses. You can either create an

extended named ACL together with an ACL filter entry in the Global Configuration

mode, or you can use the IPv4 Extended ACL Configuration mode for sequenced

ACL filter entry after entering a list name.

The no variant of this command removes a specified extended named access-list.

Syntax

[list-name]

access-list extended <list-name>

no access-list extended <list-name>

Syntax [icmp] access-list extended <list-name>{deny|permit} icmp <source>

<destination> [icmp-type <type-number>] [log]

no access-list extended <list-name>{deny|permit} icmp <source>

<destination> [icmp-type <type-number>] [log]

Parameter Description

<list-name>A user-defined name for the access-list

Table 25-2: Parameters in the access-list extended (named) command - icmp

Parameter Description

<list-name>A user-defined name for the access-list.

deny The access-list rejects packets that match the type, source, and

destination filtering specified with this command.

permit The access-list permits packets that match the type, source, and

destination filtering specified with this command.

icmp The access-list matches only ICMP packets.

icmp-type Matches only a specified type of ICMP messages. This is valid only

when the filtering is set to match ICMP packets.

613-50137-01 Rev A Command Reference for FS980M Series 805

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST EXTENDED (NAMED)

<source> The source address of the packets. You can specify a single host, a

subnet, or all sources. The following are the valid formats for

specifying the source:

any Matches any source IP address.

host<ip-addr> Matches a single source host with the

IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/

An IPv4 address, followed by a forward

slash, then the prefix length. This

matches any source IP address within

the specified subnet.

<ip-addr>

<reverse-mask>

Alternatively, you can enter a reverse

mask in dotted decimal format. For

example, entering 192.168.1.1

0.0.0.255 is the same as entering

192.168.1.1/24.

<destination>The destination address of the packets. You can specify a single

host, a subnet, or all destinations. The following are the valid

formats for specifying the destination:

any Matches any destination IP address.

host<ip-addr> Matches a single destination host with

the IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/

An IPv4 address, followed by a forward

slash, then the prefix length. This

matches any destination IP address

within the specified subnet.

<ip-addr>

<reverse-mask>

Alternatively, you can enter a reverse

mask in dotted decimal format. For

example, entering 192.168.1.1

0.0.0.255 is the same as entering

192.168.1.1/24.

Table 25-2: Parameters in the access-list extended (named) command - icmp

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 806

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST EXTENDED (NAMED)

Syntax [tcp|udp] access-list extended <list-name> {deny|permit} {tcp|udp}

<source> eq <sourceport> <destination> eq <destport> [log]

no access-list extended <list-name> {deny|permit} {tcp|udp}

<source> eq <sourceport> <destination> eq <destport> [log]

<type-number>The ICMP type, as defined in RFC792 and RFC950. Specify one of

the following integers to create a filter for the ICMP message type:

0Echo replies.

3Destination unreachable messages.

4Source quench messages.

5Redirect (change route) messages.

8Echo requests.

11 Time exceeded messages.

12 Parameter problem messages.

13 Timestamp requests.

14 Timestamp replies.

15 Information requests.

16 Information replies.

17 Address mask requests.

18 Address mask replies.

log Logs the results.

Table 25-2: Parameters in the access-list extended (named) command - icmp

Parameter Description

Table 25-3: Parameters in the access-list extended (named) command - tcp|udp

Parameter Description

<list-name>A user-defined name for the access-list.

deny The access-list rejects packets that match the type, source, and

destination filtering specified with this command.

permit The access-list permits packets that match the type, source, and

destination filtering specified with this command.

tcp The access-list matches only TCP packets.

udp The access-list matches only UDP packets.

613-50137-01 Rev A Command Reference for FS980M Series 807

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST EXTENDED (NAMED)

Syntax

[proto|any| ip]

access-list extended <list-name> {deny|permit} {proto

<ip-protocol>|any|ip} {<source>} {<destination>} [log]

no access-list extended <list-name>{deny|permit} {proto

<ip-protocol>|any|ip}{<source>}{<destination>}[log]

<source> The source address of the packets. You can specify a single host, a

subnet, or all sources. The following are the valid formats for

specifying the source:

any Matches any source IP address.

host<ip-addr> Matches a single source host with the

IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/

An IPv4 address, followed by a forward

slash, then the prefix length. This

matches any source IP address within

the specified subnet.

<ip-addr>

<reverse-mask>

Alternatively, you can enter a reverse

mask in dotted decimal format. For

example, entering 192.168.1.1

0.0.0.255 is the same as entering

192.168.1.1/24.

<destination>The destination address of the packets. You can specify a single

host, a subnet, or all destinations. The following are the valid

formats for specifying the destination:

any Matches any destination IP address.

host<ip-addr> Matches a single destination host with

the IP address given by <ip-addr> in

dotted decimal notation.

<ip-addr>/

An IPv4 address, followed by a forward

slash, then the prefix length. This

matches any destination IP address

within the specified subnet.

<ip-addr>

<reverse-mask>

Alternatively, you can enter a reverse

mask in dotted decimal format. For

example, entering 192.168.1.1

0.0.0.255 is the same as entering

192.168.1.1/24.

<sourceport>The source port number, specified as an integer between 0 and

65535.

<destport>The destination port number, specified as an integer between 0

and 65535.

eq Matches port numbers equal to the port number specified

immediately after this parameter.

log Log the results.

Table 25-3: Parameters in the access-list extended (named) command - tcp|udp

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 808

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST EXTENDED (NAMED)

Table 25-4: Parameters in the access-list extended (named) command -

proto|ip|any

Parameter Description

<list-name>A user-defined name for the access-list.

deny The access-list rejects packets that match the type, source, and

destination filtering specified with this command.

permit The access-list permits packets that match the type, source, and

destination filtering specified with this command.

proto Matches only a specified type of IP Protocol.

any The access-list matches any type of IP packet.

ip The access-list matches only IP packets.

<source> The source address of the packets. You can specify a single host, a

subnet, or all sources. The following are the valid formats for

specifying the source:

any Matches any source IP address.

host<ip-addr> Matches a single source host with the IP

address given by <ip-addr> in dotted

decimal notation.

<ip-addr>/

An IPv4 address, followed by a forward

slash, then the prefix length. This matches

any source IP address within the specified

subnet.

<ip-addr>

<reverse-mask>

Alternatively, you can enter a reverse mask

in dotted decimal format. For example,

entering 192.168.1.1 0.0.0.255 is

the same as entering 192.168.1.1/24.

<destination>The destination address of the packets. You can specify a single

host, a subnet, or all destinations. The following are the valid

formats for specifying the destination:

any Matches any destination IP address.

host<ip-addr> Matches a single destination host with the

IP address given by <ip-addr> in dotted

decimal notation.

<ip-addr>/

An IPv4 address, followed by a forward

slash, then the prefix length. This matches

any destination IP address within the

specified subnet.

<ip-addr>

<reverse-mask>

Alternatively, you can enter a reverse mask

in dotted decimal format. For example,

entering 192.168.1.1 0.0.0.255 is

the same as entering 192.168.1.1/24.

613-50137-01 Rev A Command Reference for FS980M Series 809

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST EXTENDED (NAMED)

log Logs the results.

<ip-protocol> The IP protocol number, as defined by IANA (Internet Assigned

Numbers Authority

www.iana.org/assignments/protocol-numbers) 

See below for a list of IP protocol numbers and their descriptions.

Table 25-5: IP protocol number and description

Protocol Number Protocol Description [RFC]

1Internet Control Message [RFC792]

2Internet Group Management [RFC1112]

3Gateway-to-Gateway [RFC823]

4IP in IP [RFC2003]

5Stream [RFC1190] [RFC1819]

6TCP (Transmission Control Protocol) [RFC793]

8EGP (Exterior Gateway Protocol) [RFC888]

9IGP (Interior Gateway Protocol) [IANA]

11 Network Voice Protocol [RFC741]

17 UDP (User Datagram Protocol) [RFC768]

20 Host monitoring [RFC869]

27 RDP (Reliable Data Protocol) [RFC908]

28 IRTP (Internet Reliable Transaction Protocol) [RFC938]

29 ISO-TP4 (ISO Transport Protocol Class 4) [RFC905]

30 Bulk Data Transfer Protocol [RFC969]

33 DCCP (Datagram Congestion Control Protocol)

[RFC4340]

48 DSR (Dynamic Source Routing Protocol) [RFC4728]

50 ESP (Encap Security Payload) [RFC2406]

51 AH (Authentication Header) [RFC2402]

54 NARP (NBMA Address Resolution Protocol) [RFC1735]

58 ICMP for IPv6 [RFC1883]

59 No Next Header for IPv6 [RFC1883]

60 Destination Options for IPv6 [RFC1883]

88 EIGRP (Enhanced Interior Gateway Routing Protocol)

Table 25-4: Parameters in the access-list extended (named) command -

proto|ip|any (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 810

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST EXTENDED (NAMED)

Mode Global Configuration

Default Any traffic controlled by a software ACL that does not explicitly match a filter is

denied.

Usage Use this command when configuring access-lists for filtering IP software packets.

You can either create access-lists from within this command, or you can enter

access-list extended followed by only the name. Entering only the name moves

you to the IPv4 Extended ACL Configuration mode for the selected access-list.

From there you can configure your access-lists by using the commands (access-list

extended ICMP filter), (access-list extended IP filter), and (access-list extended IP

protocol filter).

Note that packets must match both the source and the destination details.

NOTE: Software ACLs will deny access unless explicitly permitted by an ACL action.

Examples You can enter the extended named ACL in the Global Configuration mode

together with the ACL filter entry on the same line, as shown below:

awplus# configure terminal

awplus(config)# access-list extended TK deny tcp 2.2.2.3/24 eq

14 3.3.3.4/24 eq 12 log

89 OSPFIGP [RFC1583]

97 Ethernet-within-IP Encapsulation / RFC3378

98 Encapsulation Header / RFC1241

108 IP Payload Compression Protocol / RFC2393

112 Virtual Router Redundancy Protocol / RFC3768

134 RSVP-E2E-IGNORE / RFC3175

135 Mobility Header / RFC3775

136 UDPLite / RFC3828

137 MPLS-in-IP / RFC4023

138 MANET Protocols / RFC-ietf-manet-iana-07.txt

139-252 Unassigned / IANA

253 Use for experimentation and testing / RFC3692

254 Use for experimentation and testing / RFC3692

255 Reserved / IANA

Table 25-5: IP protocol number and description (cont.)

Protocol Number Protocol Description [RFC]

613-50137-01 Rev A Command Reference for FS980M Series 811

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST EXTENDED (NAMED)

Alternatively, you can enter the extended named ACL in Global Configuration

mode before specifying the ACL filter entry in the IPv4 Extended ACL

Configuration mode, as shown below:

awplus# configure terminal

awplus(config)# access-list extended TK

awplus(config-ip-ext-acl)# deny tcp 2.2.2.3/24 eq 14 3.3.3.4/24

eq 12 log

613-50137-01 Rev A Command Reference for FS980M Series 812

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (EXTENDED NUMBERED)

access-list (extended numbered)

Overview This command configures an extended numbered access-list that permits or

denies packets from specific source and destination IP addresses. You can either

create an extended numbered ACL together with an ACL filter entry in the Global

Configuration mode, or you can use the IPv4 Extended ACL Configuration mode

for sequenced ACL filter entry after entering a list number.

The no variant of this command removes a specified extended named access-list.

Syntax

[list-number]

access-list {<100-199>|<2000-2699>}

no access-list {<100-199>|<2000-2699>}

Syntax [deny|

permit]

access-list {<100-199>|<2000-2699>} {deny|permit} ip <source>

no access-list {<100-199>|<2000-2699>}{deny|permit} ip <source>

Parameter Description

<100-199>IP extended access-list.

<2000-2699>IP extended access-list (expanded range).

Parameter Description

<100-199>IP extended access-list.

<2000-2699>IP extended access-list (expanded range).

deny Access-list rejects packets that match the source and destination

filtering specified with this command.

permit Access-list permits packets that match the source and destination

filtering specified with this command.

<source>The source address of the packets. You can specify a single host, a

subnet, or all sources. The following are the valid formats for

specifying the source:

any Matches any source IP address.

host<ip-addr> Matches a single source host with the IP

address given by <ip-addr> in dotted

decimal notation.

<ip-addr>

<reverse-mask>

An IPv4 address, followed by a reverse

mask in dotted decimal format. For

example, entering 192.168.1.1

0.0.0.255 is the same as entering

192.168.1.1/24. This matches any

source IP address within the specified

subnet.

613-50137-01 Rev A Command Reference for FS980M Series 813

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (EXTENDED NUMBERED)

Mode Global Configuration

Default Any traffic controlled by a software ACL that does not explicitly match a filter is

denied.

Usage Use this command when configuring access-list for filtering IP software packets.

You can either create access-lists from within this command, or you can enter

access-list followed by only the number. Entering only the number moves you to

the IPv4 Extended ACL Configuration mode for the selected access-list. From there

you can configure your access-lists by using the commands (access-list extended

ICMP filter), (access-list extended IP filter), and (access-list extended IP protocol

filter).

Note that packets must match both the source and the destination details.

NOTE: Software ACLs will deny access unless explicitly permitted by an ACL action.

Examples You can enter the extended ACL in the Global Configuration mode together with

the ACL filter entry on the same line, as shown below:

awplus# configure terminal

awplus(config)# access-list 101 deny ip 172.16.10.0 0.0.0.255

any

Alternatively, you can enter the extended ACL in Global Configuration mode

before specifying the ACL filter entry in the IPv4 Extended ACL Configuration

mode, as shown below:

awplus# configure terminal

awplus(config)# access-list 101

awplus(config-ip-ext-acl)# deny ip 172.16.10.0 0.0.0.255 any

<destination>The destination address of the packets. You can specify a single

host, a subnet, or all destinations. The following are the valid

formats for specifying the destination:

any Matches any destination IP address.

host<ip-addr> Matches a single destination host with the

IP address given by <ip-addr> in dotted

decimal notation.

<ip-addr>

<reverse-mask>

An IPv4 address, followed by a reverse

mask in dotted decimal format. For

example, entering 192.168.1.1

0.0.0.255 is the same as entering

192.168.1.1/24. This matches any

destination IP address within the specified

subnet.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 814

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

(ACCESS-LIST EXTENDED ICMP FILTER)

(access-list extended ICMP filter)

Overview Use this ACL filter to add a new ICMP filter entry to the current extended access-list.

If the sequence number is specified, the new filter is inserted at the specified

location. Otherwise, the new filter is added at the end of the access-list.

The no variant of this command removes an ICMP filter entry from the current

extended access-list. You can specify the ICMP filter entry for removal by entering

either its sequence number (e.g. no 10), or by entering its ICMP filter profile

without specifying its sequence number.

Note that the sequence number can be found by running the show access-list (IPv4

Software ACLs) command.

Syntax [icmp] [<sequence-number>] {deny|permit} icmp <source> <destination>

[icmp-type <icmp-value>] [log]

no {deny|permit} icmp <source> <destination>[icmp-type

<icmp-value>] [log]

no <sequence-number>

Parameter Description

<sequence-

number>

<1-65535>

The sequence number for the filter entry of the selected access

control list.

deny Access-list rejects packets that match the source and destination

filtering specified with this command.

permit Access-list permits packets that match the source and destination

filtering specified with this command.

icmp ICMP packet type.

<source>The source address of the packets. You can specify a single host, a

subnet, or all sources. The following are the valid formats for

specifying the source:

<ip-addr>/

An IPv4 address, followed by a

forward slash, then the prefix length.

This matches any source IP address

within the specified subnet.

any Matches any source IP address.

<destination>The destination address of the packets. You can specify a single

host, a subnet, or all destinations. The following are the valid

formats for specifying the destination:

<ip-addr>/

An IPv4 address, followed by a

forward slash, then the prefix length.

This matches any destination IP

address within the specified subnet.

any Matches any destination IP address.

613-50137-01 Rev A Command Reference for FS980M Series 815

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

(ACCESS-LIST EXTENDED ICMP FILTER)

Mode IPv4 Extended ACL Configuration

Default Any traffic controlled by a software ACL that does not explicitly match a filter is

denied.

Usage An ACL can be configured with multiple ACL filters using sequence numbers. If the

sequence number is omitted, the next available multiple of 10 will be used as the

sequence number for the new filter. A new ACL filter can be inserted into the

middle of an existing list by specifying the appropriate sequence number.

NOTE: The access control list being configured is selected by running the access-list

(extended numbered) command or the access-list extended (named) command, with

the required access control list number, or name - but with no further parameters

selected.

Software ACLs will deny access unless explicitly permitted by an ACL action.

Examples To add a new entry in access-list called my-list that will reject ICMP packets from

10.0.0.1 to 192.168.1.1, use the commands:

awplus# configure terminal

awplus(config)# access-list extended my-list

awplus(config-ip-ext-acl)# deny icmp 10.0.0.1/32 192.168.1.1/32

Use the following commands to add a new filter at sequence number 5 position of

the access-list called my-list. The filter will accept the ICMP type 8 packets from

10.1.1.0/24 network, to 192.168.1.0 network:

awplus# configure terminal

awplus(config)# access-list extended my-list

awplus(config-ip-ext-acl)# 5 permit icmp 10.1.1.0/24

192.168.1.0/24 icmp-type 8

icmp-type The ICMP type.

<icmp-value>The value of the ICMP

type.

log Log the results.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 816

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

(ACCESS-LIST EXTENDED IP FILTER)

(access-list extended IP filter)

Overview Use this ACL filter to add a new IP filter entry to the current extended access-list. If

the sequence number is specified, the new filter is inserted at the specified

location. Otherwise, the new filter is added at the end of the access-list.

The no variant of this command removes an IP filter entry from the current

extended access-list. You can specify the IP filter entry for removal by entering

either its sequence number (e.g. no 10), or by entering its IP filter profile without

specifying its sequence number.

Note that the sequence number can be found by running the show access-list (IPv4

Software ACLs) command.

Syntax [ip] [<sequence-number>] {deny|permit} ip <source> <destination>

no {deny|permit} ip <source> <destination>

no <sequence-number>

Parameter Description

<sequence-

number>

<1-65535>

The sequence number for the filter entry of the selected access

control list.

deny Access-list rejects packets that match the source and destination

filtering specified with this command.

permit Access-list permits packets that match the source and destination

filtering specified with this command.

<source> The source address of the packets. You can specify a single host, a

subnet, or all sources. The following are the valid formats for

specifying the source:

any Matches any source IP address.

host<ip-addr> Matches a single source host with the IP

address given by <ip-addr> in dotted

decimal notation.

<ip-addr>

<reverse-mask>

Alternatively, enter an IPv4 address

followed by a reverse mask in dotted

decimal format. For example, enter

192.168.1.1 0.0.0.255.

613-50137-01 Rev A Command Reference for FS980M Series 817

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

(ACCESS-LIST EXTENDED IP FILTER)

Mode Extended ACL Configuration

Default Any traffic controlled by a software ACL that does not explicitly match a filter is

denied.

Usage An ACL can be configured with multiple ACL filters using sequence numbers. If the

sequence number is omitted, the next available multiple of 10 will be used as the

sequence number for the new filter. A new ACL filter can be inserted into the

middle of an existing list by specifying the appropriate sequence number.

NOTE: The access control list being configured is selected by running the access-list

(extended numbered) command or the access-list extended (named) command, with

the required access control list number, or name - but with no further parameters

selected.

Software ACLs will deny access unless explicitly permitted by an ACL action.

Example 1

[list-number]

First use the following commands to enter the IPv4 Extended ACL Configuration

mode and define a numbered extended access-list 101:

awplus# configure terminal

awplus(config)# access-list 101

awplus(config-ip-ext-acl)#

Then use the following commands to add a new entry to the numbered extended

access- list 101 that will reject packets from 10.0.0.1 to 192.168.1.1:

awplus(config-ip-ext-acl)# deny ip host 10.0.0.1 host

192.168.1.1

awplus(config-ip-ext-acl)# 20 permit ip any any

Example 2

[list-name]

First use the following commands to enter the IPv4 Extended ACL Configuration

mode and define a named access-list called my-acl:

awplus# configure terminal

awplus(config)# access-list extended my-acl

awplus(config-ip-ext-acl)#

<destination>The destination address of the packets. You can specify a single

host, a subnet, or all destinations. The following are the valid

formats for specifying the destination:

any Matches any destination IP address.

host<ip-addr> Matches a single destination host with the

IP address given by <ip-addr> in dotted

decimal notation.

<ip-addr>

<reverse-mask>

Alternatively, enter an IPv4 address

followed by a reverse mask in dotted

decimal format. For example, enter

192.168.1.1 0.0.0.255.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 818

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

(ACCESS-LIST EXTENDED IP FILTER)

Then use the following commands to add a new entry to the named access-list

my-acl that will reject packets from 10.0.0.1 to 192.168.1.1:

awplus(config-ip-ext-acl)# deny ip host 10.0.0.1 host

192.168.1.1

awplus(config-ip-ext-acl)# 20 permit ip any any

Example 3

[list-number]

Use the following commands to remove the access-list filter entry with sequence

number 20 from extended numbered access-list 101.

awplus# configure terminal

awplus(config)# access-list 101

awplus(config-ip-ext-acl)# no 20

Example 4

[list-name]

Use the following commands to remove the access-list filter entry with sequence

number 20 from extended named access-list my-acl:

awplus# configure terminal

awplus(config)# access-list extended my-acl

awplus(config-ip-ext-acl)# no 20

613-50137-01 Rev A Command Reference for FS980M Series 819

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

(ACCESS-LIST EXTENDED IP PROTOCOL FILTER)

(access-list extended IP protocol filter)

Overview Use this ACL filter to add a new IP protocol type filter entry to the current extended

access-list. If the sequence number is specified, the new filter is inserted at the

specified location. Otherwise, the new filter is added at the end of the access-list.

The no variant of this command removes an IP protocol filter entry from the

current extended access-list. You can specify the IP filter entry for removal by

entering either its sequence number (e.g. no 10), or by entering its IP filter profile

without specifying its sequence number.

Note that the sequence number can be found by running the show access-list (IPv4

Software ACLs) command.

Syntax [proto] [<sequence-number>] {deny|permit} proto <ip-protocol> <source>

<destination> [log]

no {deny|permit} proto <ip-protocol> <source> <destination>

[log]

no <sequence-number>

Parameter Description

<sequence-

number>

<1-65535>

The sequence number for the filter entry of the selected access

control list.

deny Access-list rejects packets that match the source and destination

filtering specified with this command.

permit Access-list permits packets that match the source and destination

filtering specified with this command.

proto

<ip-protocol>

<1-255>

Specify IP protocol number, as defined by IANA (Internet Assigned

Numbers Authority

www.iana.org/assignments/protocol-numbers)

See below for a list of IP protocol numbers and their descriptions.

<source>The source address of the packets. You can specify a single host, a

subnet, or all sources. The following are the valid formats for

specifying the source:

<ip-addr>/

An IPv4 address, followed by a forward

slash, then the prefix length. This matches

any source IP address within the specified

subnet.

any Matches any source IP address.

613-50137-01 Rev A Command Reference for FS980M Series 820

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

(ACCESS-LIST EXTENDED IP PROTOCOL FILTER)

<destination>The destination address of the packets. You can specify a single

host, a subnet, or all destinations. The following are the valid

formats for specifying the destination:

<ip-addr>/

An IPv4 address, followed by a forward

slash, then the prefix length. This matches

any destination IP address within the

specified subnet.

any Matches any destination IP address.

log Log the results.

Table 25-6: IP protocol number and description

Protocol Number Protocol Description [RFC]

1Internet Control Message [RFC792]

2Internet Group Management [RFC1112]

3Gateway-to-Gateway [RFC823]

4IP in IP [RFC2003]

5Stream [RFC1190] [RFC1819]

6TCP (Transmission Control Protocol) [RFC793]

8EGP (Exterior Gateway Protocol) [RFC888]

9IGP (Interior Gateway Protocol) [IANA]

11 Network Voice Protocol [RFC741]

17 UDP (User Datagram Protocol) [RFC768]

20 Host monitoring [RFC869]

27 RDP (Reliable Data Protocol) [RFC908]

28 IRTP (Internet Reliable Transaction Protocol) [RFC938]

29 ISO-TP4 (ISO Transport Protocol Class 4) [RFC905]

30 Bulk Data Transfer Protocol [RFC969]

33 DCCP (Datagram Congestion Control Protocol)

[RFC4340]

48 DSR (Dynamic Source Routing Protocol) [RFC4728]

50 ESP (Encap Security Payload) [RFC2406]

51 AH (Authentication Header) [RFC2402]

54 NARP (NBMA Address Resolution Protocol) [RFC1735]

58 ICMP for IPv6 [RFC1883]

59 No Next Header for IPv6 [RFC1883]

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 821

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

(ACCESS-LIST EXTENDED IP PROTOCOL FILTER)

Mode IPv4 Extended ACL Configuration

Default Any traffic controlled by a software ACL that does not explicitly match a filter is

denied.

Usage An ACL can be configured with multiple ACL filters using sequence numbers. If the

sequence number is omitted, the next available multiple of 10 will be used as the

sequence number for the new filter. A new ACL filter can be inserted into the

middle of an existing list by specifying the appropriate sequence number.

NOTE: The access control list being configured is selected by running the access-list

(extended numbered) command or the access-list extended (named) command, with

the required access control list number, or name - but with no further parameters

selected.

Software ACLs will deny access unless explicitly permitted by an ACL action.

Example 1

[creating a list]

Use the following commands to add a new access-list filter entry to the access-list

named my-list that will reject IP packets from source address 10.10.1.1/32

to destination address 192.68.1.1/32:

awplus# configure terminal

awplus(config)# access-list extended my-list

awplus(config-ip-ext-acl)# deny ip 10.10.1.1/32 192.168.1.1/32

60 Destination Options for IPv6 [RFC1883]

88 EIGRP (Enhanced Interior Gateway Routing Protocol)

89 OSPFIGP [RFC1583]

97 Ethernet-within-IP Encapsulation / RFC3378

98 Encapsulation Header / RFC1241

108 IP Payload Compression Protocol / RFC2393

112 Virtual Router Redundancy Protocol / RFC3768

134 RSVP-E2E-IGNORE / RFC3175

135 Mobility Header / RFC3775

136 UDPLite / RFC3828

137 MPLS-in-IP / RFC4023

138 MANET Protocols / RFC-ietf-manet-iana-07.txt

139-252 Unassigned / IANA

253 Use for experimentation and testing / RFC3692

254 Use for experimentation and testing / RFC3692

255 Reserved / IANA

Table 25-6: IP protocol number and description (cont.)

Protocol Number Protocol Description [RFC]

613-50137-01 Rev A Command Reference for FS980M Series 822

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

(ACCESS-LIST EXTENDED IP PROTOCOL FILTER)

Example 2

[adding to a list]

Use the following commands to add a new access-list filter entry at sequence

position 5 in the access-list named my-list that will accept packets from source

address 10.10.1.1/24 to destination address 192.68.1.1/24:

awplus# configure terminal

awplus(config)# access-list extended my-list

awplus(config-ip-ext-acl)# 5 permit ip 10.10.1.1/24

192.168.1.1/ 24

613-50137-01 Rev A Command Reference for FS980M Series 823

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

(ACCESS-LIST EXTENDED TCP UDP FILTER)

(access-list extended TCP UDP filter)

Overview Use this ACL filter to add a new TCP or UDP filter entry to the current extended

access-list. If the sequence number is specified, the new filter is inserted at the

specified location. Otherwise, the new filter is added at the end of the access-list.

The no variant of this command removes a TCP or UDP filter entry from the current

extended access-list. You can specify the TCP or UDP filter entry for removal by

entering either its sequence number (e.g. no 10), or by entering its TCP or UDP

filter profile without specifying its sequence number.

Note that the sequence number can be found by running the show access-list (IPv4

Software ACLs) command.

Syntax [tcp|udp] [<sequence-number>] {deny|permit} {tcp|udp} <source> eq

<sourceport> <destination> eq <destport> [log]

no [<sequence-number>] {deny|permit} {tcp|udp} <source> eq

<sourceport> <destination> eq <destport> [log]

no [<sequence-number>]

Parameter Description

<sequence-

number>

<1-65535>

The sequence number for the filter entry of the selected access

control list.

deny Access-list rejects packets that match the source and destination

filtering specified with this command.

permit Access-list permits packets that match the source and destination

filtering specified with this command.

tcp The access-list matches only TCP packets.

udp The access-list matches only UDP packets.

<source>The source address of the packets. You can specify a single host, a

subnet, or all sources. The following are the valid formats for

specifying the source:

<ip-addr>/

An IPv4 address, followed by a

forward slash, then the prefix length.

This matches any source IP address

within the specified subnet.

any Matches any source IP address.

<sourceport>The source port number, specified as an integer between 0 and

65535.

613-50137-01 Rev A Command Reference for FS980M Series 824

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

(ACCESS-LIST EXTENDED TCP UDP FILTER)

Mode IPv4 Extended ACL Configuration

Default Any traffic controlled by a software ACL that does not explicitly match a filter is

denied.

Usage An ACL can be configured with multiple ACL filters using sequence numbers. If the

sequence number is omitted, the next available multiple of 10 will be used as the

sequence number for the new filter. A new ACL filter can be inserted into the

middle of an existing list by specifying the appropriate sequence number.

NOTE: The access control list being configured is selected by running the access-list

(extended numbered) command or the access-list extended (named) command, with

the required access control list number, or name - but with no further parameters

selected.

Software ACLs will deny access unless explicitly permitted by an ACL action.

Example 1

[creating a list]

To add a new entry to the access-list named my-list that will reject TCP packets

from 10.0.0.1on TCP port 10 to 192.168.1.1 on TCP port 20, use the

commands:

awplus# configure terminal

awplus(config)# access-list extended my-list

awplus(config-ip-ext-acl)# deny tcp 10.0.0.1/32 eq 10

192.168.1.1/32 eq 20

Example 2

[adding to a list]

To insert a new entry with sequence number 5 of the access-list named my-list

that will accept UDP packets from 10.1.1.0/24 network to 192.168.1.0/24

network on UDP port 80, use the commands:

awplus# configure terminal

awplus(config)# access-list extended my-list

awplus(config-ip-ext-acl)# 5 permit udp 10.1.1.0/24

192.168.1.0/24 eq 80

<destination>The destination address of the packets. You can specify a single

host, a subnet, or all destinations. The following are the valid

formats for specifying the destination:

<ip-addr>/

An IPv4 address, followed by a

forward slash, then the prefix length.

This matches any destination IP

address within the specified subnet.

any Matches any destination IP address.

<destport>The destination port number, specified as an integer between 0

and 65535.

eq Matches port numbers equal to the port number specified

immediately after this parameter.

log Log the results.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 825

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST STANDARD (NAMED)

access-list standard (named)

Overview This command configures a standard named access-list that permits or denies

packets from a specific source IP address. You can either create a standard named

ACL together with an ACL filter entry in the Global Configuration mode, or you can

use the IPv4 Standard ACL Configuration mode for sequenced ACL filter entry after

first entering an access-list name.

The no variant of this command removes a specified standard named access-list.

Syntax

[list-name]

access-list standard <standard-access-list-name>

no access-list standard <standard-access-list-name>

Syntax

[deny|permit]

access-list standard <standard-access-list-name> {deny|permit}

no access-list standard <standard-access-list-name>

{deny|permit} <source>

Mode Global Configuration

Default Any traffic controlled by a software ACL that does not explicitly match a filter is

denied.

Parameter Description

<standard-access-list-name

Specify a name for the standard access-list.

Parameter Description

<standard-

access-list-

name>

Specify a name for the standard access-list.

deny The access-list rejects packets that match the source filtering

specified with this command.

permit The access-list permits packets that match the source filtering

specified with this command.

<source>The source address of the packets. You can specify a single host, a

subnet, or all sources. The following are the valid formats for

specifying the source:

<ip-addr>/<prefix>An IPv4 address, followed by a

forward slash, then the prefix

length. This matches any source

IP address within the specified

subnet.

any Matches any source IP address.

613-50137-01 Rev A Command Reference for FS980M Series 826

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST STANDARD (NAMED)

Usage Use this command when configuring a standard named access-list for filtering IP

software packets.

You can either create access-lists from within this command, or you can enter

access-list standard followed by only the name. Entering only the name moves

you to the IPv4 Standard ACL Configuration mode for the selected access-list. From

there you can configure your access-lists by using the command (access-list

standard named filter).

NOTE: Software ACLs will deny access unless explicitly permitted by an ACL action.

Examples To define a standard access-list named my-list and deny any packets from any

source, use the commands:

awplus# configure terminal

awplus(config)# access-list standard my-list deny any

Alternatively, to define a standard access-list named my-list and enter the IPv4

Standard ACL Configuration mode to deny any packets from any source, use the

commands:

awplus# configure terminal

awplus(config)# access-list standard my-list

awplus(config-ip-std-acl)# 5 deny any

Commands

(access-list standard named filter)

show running-config

show ip access-list

613-50137-01 Rev A Command Reference for FS980M Series 827

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (STANDARD NUMBERED)

access-list (standard numbered)

Overview This command configures a standard numbered access-list that permits or denies

packets from a specific source IP address. You can either create a standard

numbered ACL together with an ACL filter entry in the Global Configuration mode,

or you can use the IPv4 Standard ACL Configuration mode for sequenced ACL filter

entry after first entering an access-list number.

The no variant of this command removes a specified standard numbered

access-list.

Syntax

[list-number]

access-list {<1-99>|<1300-1999>}

no access-list {<1-99>|<1300-1999>}

Syntax [deny|

permit]

access-list {<1-99>|<1300-1999>} {deny|permit} <source>

no access-list {<1-99>|<1300-1999>} {deny|permit} <source>

Mode Global Configuration

Default Any traffic controlled by a software ACL that does not explicitly match a filter is

denied.

Usage Use this command when configuring a standard numbered access-list for filtering

IP software packets.

Parameter Description

<1-99>IP standard access-list.

<1300-1999>IP standard access-list (expanded range).

Parameter Description

<1-99>IP standard access-list.

<1300-1999>IP standard access-list (expanded range).

deny Access-list rejects packets from the specified source.

permit Access-list accepts packets from the specified source.

<source>The source address of the packets. You can specify a single host, a

subnet, or all sources. The following are the valid formats for

specifying the source:

<ip-addr>

<reverse-mask>

Enter an IPv4 address followed by a reverse

mask in dotted decimal format. For example,

entering 192.168.1.1 0.0.0.255 is

the same as entering 192.168.1.1/24.

any Matches any source IP address.

613-50137-01 Rev A Command Reference for FS980M Series 828

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

ACCESS-LIST (STANDARD NUMBERED)

You can either create access-lists from within this command, or you can enter

access-list followed by only the number. Entering only the number moves you to

the IPv4 Standard ACL Configuration mode for the selected access-list. From there

you can configure your access-lists by using the command (access-list standard

numbered filter).

NOTE: Software ACLs will deny access unless explicitly permitted by an ACL action.

Examples To create ACL number 67 that will deny packets from subnet 172.16.10, use the

commands:

awplus# configure terminal

awplus(config)# access-list 67 deny 172.16.10.0 0.0.0.255

Alternatively, to enter the IPv4 Standard ACL Configuration mode to create the

ACL filter and deny packets from subnet 172.16.10.0 for the standard

numbered access-list 67, use the commands:

awplus# configure terminal

awplus(config)# access-list 67

awplus(config-ip-std-acl)# deny 172.16.10.0 0.0.0.255

Commands

(access-list standard named filter)

show running-config

show ip access-list

613-50137-01 Rev A Command Reference for FS980M Series 829

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

(ACCESS-LIST STANDARD NAMED FILTER)

(access-list standard named filter)

Overview This ACL filter adds a source IP address filter entry to a current named standard

access-list. If the sequence number is specified, the new filter entry is inserted at

the specified location. Otherwise, the new entry is added at the end of the

access-list.

The no variant of this command removes a source IP address filter entry from the

current named standard access-list. You can specify the source IP address filter

entry for removal by entering either its sequence number (e.g. no 10), or by

entering its source IP address filter profile without specifying its sequence number.

Note that the sequence number can be found by running the show access-list (IPv4

Software ACLs) command.

Syntax [<sequence-number>] {deny|permit} {<source> [exact-match]|any}

no {deny|permit} {<source> [exact-match]|any}

no <sequence-number>

Mode IPv4 Standard ACL Configuration

Default Any traffic controlled by a software ACL that does not explicitly match a filter is

denied.

Parameter Description

<sequence-number><1-65535>

The sequence number for the filter entry of the

selected access control list.

deny Access-list rejects packets of the source filtering

specified.

permit Access-list allows packets of the source filtering

specified

<source>The source address of the packets. You can specify

either a subnet or all sources. The following are the

valid formats for specifying the source:

<ip-addr>/

An IPv4 address, followed by a

forward slash, then the prefix

length. This matches any

destination IP address within

the specified subnet.

<ip-addr> An IPv4 address in a.b.c.d

format.

exact-match Specify an exact IP prefix to match on.

any Matches any source IP address.

613-50137-01 Rev A Command Reference for FS980M Series 830

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

(ACCESS-LIST STANDARD NAMED FILTER)

Usage An ACL can be configured with multiple ACL filters using sequence numbers. If the

sequence number is omitted, the next available multiple of 10 will be used as the

sequence number for the new filter. A new ACL filter can be inserted into the

middle of an existing list by specifying the appropriate sequence number.

NOTE: The access control list being configured is selected by running the access-list

standard (named) command with the required access control list name, but with no

further parameters selected.

Software ACLs will deny access unless explicitly permitted by an ACL action.

Examples Use the following commands to add a new filter entry to access-list my-list that

will reject IP address 10.1.1.1:

awplus# configure terminal

awplus(config)# access-list standard my-list

awplus(config-ip-std-acl)# deny 10.1.1.1/32

Use the following commands to insert a new filter entry into access-list my-list

at sequence position number 15 that will accept IP network 10.1.2.0:

awplus# configure terminal

awplus(config)# access-list standard my-list

awplus(config-ip-std-acl)# 15 permit 10.1.2.0/24

Commands

access-list standard (named)

show running-config

show ip access-list

613-50137-01 Rev A Command Reference for FS980M Series 831

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

(ACCESS-LIST STANDARD NUMBERED FILTER)

(access-list standard numbered filter)

Overview This ACL filter adds a source IP address filter entry to a current standard numbered

access-list. If a sequence number is specified, the new filter entry is inserted at the

specified location. Otherwise, the new filter entry is added at the end of the

access-list.

The no variant of this command removes a source IP address filter entry from the

current standard numbered access-list. You can specify the source IP address filter

entry for removal by entering either its sequence number (e.g. no 10), or by

entering its source IP address filter profile without specifying its sequence number.

Note that the sequence number can be found by running the show access-list (IPv4

Software ACLs) command.

Syntax [<sequence-number>] {deny|permit} {<source>|host

<host-address>|any}

no {deny|permit} {<source>|host <host-address>|any}

no <sequence-number>

Mode IPv4 Standard ACL Configuration

Default Any traffic controlled by a software ACL that does not explicitly match a filter is

denied.

Parameter Description

<sequence-number><1-65535>

The sequence number for the filter entry of the

selected access control list.

deny Access-list rejects packets of the type specified.

permit Access-list allows packets of the type specified

<source>The source address of the packets. You can specify

either a subnet or all sources. The following are the

valid formats for specifying the source:

<ip-addr>

<reverse-mask>

Enter a reverse mask for the

source address in dotted

decimal format. For example,

entering 192.168.1.1

0.0.0.255 is the same as

entering 192.168.1.1/24.

<ip-addr> An IPv4 address in a.b.c.d

format.

host A single source host.

<host-address>Single source host address.

any Matches any source IP address.

613-50137-01 Rev A Command Reference for FS980M Series 832

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

(ACCESS-LIST STANDARD NUMBERED FILTER)

Usage An ACL can be configured with multiple ACL filters using sequence numbers. If the

sequence number is omitted, the next available multiple of 10 will be used as the

sequence number for the new filter. A new ACL filter can be inserted into the

middle of an existing list by specifying the appropriate sequence number.

NOTE: The access control list being configured is selected by running the access-list

(standard numbered) command with the required access control list number but with

no further parameters selected.

Software ACLs will deny access unless explicitly permitted by an ACL action.

Example To add a new entry accepting the IP network 10.1.1.0/24 at the sequence

number 15 position, use the commands:

awplus# configure terminal

awplus(config)# access-list 99

awplus(config-ip-std-acl)# 15 permit 10.1.2.0 0.0.0.255

Commands

access-list (standard numbered)

show running-config

show ip access-list

613-50137-01 Rev A Command Reference for FS980M Series 833

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

CLEAR IP PREFIX-LIST

clear ip prefix-list

Overview Use this command to reset the hit count to zero in the prefix-list entries.

Syntax clear ip prefix-list [<list-name>] [<ip-address>/<mask>]

Mode Privileged Exec

Example To clear a prefix-list named List1:

awplus# clear ip prefix-list List1

Parameter Description

<list-name> The name of the prefix-list.

<ip-address>/<mask> The IP prefix and length.

613-50137-01 Rev A Command Reference for FS980M Series 834

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

IP PREFIX-LIST

ip prefix-list

Overview Use this command to create an entry for an IPv4 prefix list.

Use the no variant of this command to delete the IPv4 prefix-list entry.

Syntax ip prefix-list <list-name> [seq <1-429496725>] {deny|permit}

{any|<ip-prefix>} [ge <0-32>] [le <0-32>]

ip prefix-list <list-name> description <text>

ip prefix-list sequence-number

no ip prefix-list <list-name> [seq <1-429496725>]

no ip prefix-list <list-name> [description <text>]

no ip prefix-list sequence-number

Mode Global Configuration

Usage When the device processes a prefix list, it starts to match prefixes from the top of

the prefix list, and stops whenever a permit or deny occurs. To promote efficiency,

use the seq parameter and place common permits or denials towards the top of

the list. If you do not use the seq parameter, the sequence values are generated in

a sequence of 5.

The parameters ge and le specify the range of the prefix lengths to be matched.

When setting these parameters, set the le value to be less than 32, and the ge value

to be less than or equal to the le value and greater than the ip-prefix mask length.

Prefix lists implicitly exclude prefixes that are not explicitly permitted in the prefix

list. This means if a prefix that is being checked against the prefix list reaches the

end of the prefix list without matching a permit or deny, this prefix will be denied.

Parameter Description

<list-name> Specifies the name of a prefix list.

seq <1-429496725>Sequence number of the prefix list entry.

deny Specifies that the prefixes are excluded from the list.

permit Specifies that the prefixes are included in the list.

<ip-prefix> Specifies the IPv4 address and length of the network

mask in dotted decimal in the format A.B.C.D/M.

any Any prefix match. Same as 0.0.0.0/0 le 32.

ge<0-32>Specifies the minimum prefix length to be matched.

le<0-32>Specifies the maximum prefix length to be matched.

<text> Text description of the prefix list.

sequence-number Specify sequence numbers included or excluded in prefix

list.

613-50137-01 Rev A Command Reference for FS980M Series 835

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

IP PREFIX-LIST

Example In the below sample configuration, the last ip prefix-list command in the

below list matches all, and the first ip prefix-list command denies the IP

network 76.2.2.0:

awplus(config)# router bgp 100

awplus(config-router)# network 172.1.1.0

awplus(config-router)# network 172.1.2.0

awplus(config-router)# neighbor 10.6.5.3 remote-as 300

awplus(config-router)# neighbor 10.6.5.3 prefix-list mylist out

awplus(config-router)# exit

awplus(config)# ip prefix-list mylist seq 5 deny 76.2.2.0/24

awplus(config)# ip prefix-list mylist seq 100 permit any

To deny the IP addresses between 10.0.0.0/14 (10.0.0.0 255.252.0.0)

and 10.0.0.0/22 (10.0.0.0 255.255.252.0) within the

10.0.0.0/8(10.0.0.0 255.0.0.0) addressing range, enter the following

commands:

awplus# configure terminal

awplus(config)# ip prefix-list mylist seq 12345 deny 10.0.0.0/8

ge 14 le 22

613-50137-01 Rev A Command Reference for FS980M Series 836

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

MAXIMUM-ACCESS-LIST

maximum-access-list

Overview Sets the maximum number of filters that can be added to any access-list. These are

access-lists within the ranges <1-199>, <1300-1999> and <2000-2699> and

named standard and extended access-lists.

The no variant of this command removes the limit on the number of filters that can

be added to a software access-list

Syntax maximum-access-list <1-4294967294>

no maximum-access-list

Mode Global Configuration

Example To set the maximum number of software filters to 200:

awplus# configure terminal

awplus(config)# maximum-access-list 200

Parameter Description

<1-4294967294>Filter range.

613-50137-01 Rev A Command Reference for FS980M Series 837

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

SHOW ACCESS-LIST (IPV4 SOFTWARE ACLS)

show access-list (IPv4 Software ACLs)

Overview Use this command to display the specified access-list, or all access-lists if none have

been specified. Note that only defined access-lists are displayed. An error message

is displayed for an undefined access-list

Syntax show access-list

[<1-99>|<100-199>|<1300-1999>|<2000-2699>|<3000-3699>|

<4000-4499>|<access-list-name>]

Mode User Exec and Privileged Exec

Examples To show all access-lists configured on the switch:

awplus# show access-list

To show the access-list with an ID of 20:

awplus# show access-list 20

Parameter Description

<1-99>IP standard access-list.

<100-199>IP extended access-list.

<1300-1999>IP standard access-list (standard - expanded range).

<2000-2699>IP extended access-list (extended - expanded range).

<3000-3699>Hardware IP access-list.

<4000-4499>Hardware MAC access-list.

<access-list-name>IP named access-list.



Standard IP access list 1

deny 172.16.2.0, wildcard bits 0.0.0.255

Standard IP access list 20

deny 192.168.10.0, wildcard bits 0.0.0.255

deny 192.168.12.0, wildcard bits 0.0.0.255

Hardware IP access list 3001

permit ip 192.168.20.0 255.255.255.0 any

Hardware IP access list 3020

permit tcp any 192.0.2.0/24

awplus#show access-list 20

613-50137-01 Rev A Command Reference for FS980M Series 838

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

SHOW ACCESS-LIST (IPV4 SOFTWARE ACLS)

Note the following error message is displayed if you attempt to show an undefined

access-list:

awplus# show access-list 2

Commands

access-list standard (named)

access-list (standard numbered)

access-list (extended numbered)



Standard IP access-list 20

deny 192.168.10.0, wildcard bits 0.0.0.255

deny 192.168.12.0, wildcard bits 0.0.0.255



% Can't find access-list 2

613-50137-01 Rev A Command Reference for FS980M Series 839

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

SHOW IP ACCESS-LIST

show ip access-list

Overview Use this command to display IP access-lists.

Syntax show ip access-list

[<1-99>|<100-199>|<1300-1999>|<2000-2699>|<access-list-name>]

Mode User Exec and Privileged Exec

Example awplus# show ip access-list

Output Figure 25-1: Example output from the show ip access-list command

Parameter Description

<1-99>IP standard access-list.

<100-199>IP extended access-list.

<1300-1999>IP standard access-list (expanded range).

<2000-2699>IP extended access-list (expanded range).

<access-list-name>IP named access-list.

Standard IP access-list 1

permit 172.168.6.0, wildcard bits 0.0.0.255

permit 192.168.6.0, wildcard bits 0.0.0.255

613-50137-01 Rev A Command Reference for FS980M Series 840

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

SHOW IP PREFIX-LIST

show ip prefix-list

Overview Use this command to display the IPv4 prefix-list entries. Note that this command is

valid for RIP and BGP routing protocols only.

Syntax show ip prefix-list [<name>|detail|summary]

Mode User Exec and Privileged Exec

Example awplus# show ip prefix-list

awplus# show ip prefix-list 10.10.0.98/8

awplus# show ip prefix-list detail

Commands

ip prefix-list

Parameter Description

<name> Specify the name of a prefix list in this placeholder.

detail Specify this parameter to show detailed output for all IPv4 prefix lists.

summary Specify this parameter to show summary output for all IPv4 prefix lists.

613-50137-01 Rev A Command Reference for FS980M Series 841

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV4 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

VTY ACCESS-CLASS (NUMBERED)

vty access-class (numbered)

Overview For IPv4, use this command to set a standard numbered software access list to be

the management ACL. This is then applied to all available VTY lines for controlling

remote access by Telnet and SSH. This command allows or denies packets

containing the IP addresses included in the ACL to create a connection to your

device.

ACLs that are attached using this command have an implicit deny-all filter as the

final entry in the ACL. So a typical configuration would be to permit a specific

address, or range of addresses, and rely on the deny-all filter to block all other

access.

Use the no variant of this command to remove the access list.

Syntax vty access-class {<1-99>|<1300-1999>}

no vty access-class [<1-99>|<1300-1999>]

Mode Global Configuration

Examples To set access-list 4 to be the management ACL, use the following commands:

awplus# configure terminal

awplus(config)# vty access-class 4

To remove access-list 4 from the management ACL, use the following commands:

awplus# configure terminal

awplus(config)# no vty access-class 4

Output Figure 25-2: Example output from the show running-config command

Commands

show running-config

vty ipv6 access-class (named)

Parameter Description

<1-99> IPv4 standard access-list number

<1300-1999> IPv4 standard access-list number (expanded range)

awplus#show running-config|grep access-class



vty access-class 4

613-50137-01 Rev A Command Reference for FS980M Series 842

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPv6 Software

Access Control List

(ACL) Commands

Introduction

Overview This chapter provides an alphabetical reference for the IPv6 Software Access

Control List (ACL) commands, and contains detailed command information and

command examples about IPv6 software ACLs as applied to Routing and

Multicasting, which are not applied to interfaces.

For information about ACLs, see the ACL Feature Overview and Configuration

Guide.

To apply ACLs to an LACP channel group, apply it to all the individual switch ports

in the channel group. To apply ACLs to a static channel group, apply it to the static

channel group itself. For more information on link aggregation see the following

references:

•the Link Aggregation Feature Overview_and_Configuration Guide.

•Link Aggregation Commands

Note that text in parenthesis in command names indicates usage not keyword

entry. For example, ipv6-access-list (named) indicates named IPv6 ACLs entered

as ipv6-access-list <name> where <name> is a placeholder not a keyword.

Note also that parenthesis surrounding ACL filters indicates the type of ACL filter

not the keyword entry in the CLI. For example, (ipv6 access-list standard IPv6

filter) represents command entry in the format shown in the syntax:

[<sequence-number>] {deny|permit}

{<source-ipv6-address/prefix-length>|any}

NOTE: Software ACLs will deny access unless explicitly permitted by an ACL action.

Sub-modes Many of the ACL commands operate from sub-modes that are specific to particular

ACL types. The following table shows the CLI prompts at which ACL commands are

entered.

613-50137-01 Rev A Command Reference for FS980M Series 843

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

Command List •“ipv6 access-list standard (named)” on page 844

•“(ipv6 access-list standard filter)” on page 846

•“show ipv6 access-list (IPv6 Software ACLs)” on page 848

•“vty ipv6 access-class (named)” on page 849

Table 26-1: IPv6 Software Access List Commands and Prompts

Command Name Command Mode Prompt

show ipv6 access-list (IPv6 Software

ACLs)

Privileged Exec awplus#

ipv6 access-list standard (named) Global Configuration awplus(config)#

(ipv6 access-list standard filter) IPv6 Standard ACL

Configuration

awplus(config-ipv6-std-acl)#

613-50137-01 Rev A Command Reference for FS980M Series 844

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

IPV6 ACCESS-LIST STANDARD (NAMED)

ipv6 access-list standard (named)

Overview This command configures an IPv6 standard access-list for filtering frames that

permit or deny IPv6 packets from a specific source IPv6 address.

The no variant of this command removes a specified IPv6 standard access-list.

Syntax

[list-name]

ipv6 access-list standard <ipv6-acl-list-name>

no ipv6 access-list standard <ipv6-acl-list-name>

Syntax [deny|

permit]

ipv6 access-list standard <ipv6-acl-list-name> [{deny|permit}

{<ipv6-source-address/prefix-length>|any} [exact-match]]

no ipv6 access-list standard <ipv6-acl-list-name>

[{deny|permit} {<ipv6-source-address/prefix-length>|any}

[exact-match]]

Mode Global Configuration

Default Any traffic controlled by a software ACL that does not explicitly match a filter is

denied.

Usage Use IPv6 standard access-lists to control the transmission of IPv6 packets on an

interface, and restrict the content of routing updates. The switch stops checking

the IPv6 standard access-list when a match is encountered.

Parameter Description

<ipv6-acl-list-name> A user-defined name for the IPv6 software standard

access-list.

Parameter Description

<ipv6-acl-list-name> A user-defined name for the IPv6 software standard

access-list.

deny The IPv6 software standard access-list rejects

packets that match the type, source, and destination

filtering specified with this command.

permit The IPv6 software standard access-list permits

packets that match the type, source, and destination

filtering specified with this command.

<ipv6-source-address/

prefix-length>

Specifies a source address and prefix length.

The IPv6 address prefix uses the format

X:X::/prefix-length. The prefix-length is usually set

between 0 and 64.

any Matches any source IPv6 address.

exact-match Exact match of the prefixes.

613-50137-01 Rev A Command Reference for FS980M Series 845

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

IPV6 ACCESS-LIST STANDARD (NAMED)

For backwards compatibility you can either create IPv6 standard access-lists from

within this command, or you can enter ipv6 access-list standard

followed by only the IPv6 standard access-list name. This latter (and preferred)

method moves you to the (config-ipv6-std-acl) prompt for the selected

IPv6 standard access-list, and from here you can configure the filters for this

selected IPv6 standard access-list.

NOTE: Software ACLs will deny access unless explicitly permitted by an ACL action.

Example To enter the IPv6 Standard ACL Configuration mode for the access-list named

my-list, use the commands:

awplus# configure terminal

awplus(config)# ipv6 access-list standard my-list

awplus(config-ipv6-std-acl)#

Commands

(ipv6 access-list standard filter)

show ipv6 access-list (IPv6 Software ACLs)

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 846

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

(IPV6 ACCESS-LIST STANDARD FILTER)

(ipv6 access-list standard filter)

Overview Use this ACL filter to add a filter entry for an IPv6 source address and prefix length

to the current standard IPv6 access-list. If a sequence number is specified, the new

entry is inserted at the specified location. Otherwise, the new entry is added at the

end of the access-list.

The no variant of this command removes a filter entry for an IPv6 source address

and prefix from the current standard IPv6 access-list. You can specify the filter

entry for removal by entering either its sequence number, or its filter entry profile.

Syntax [icmp] [<sequence-number>] {deny|permit}

{<ipv6-source-address/prefix-length>|any}

no {deny|permit} {<ipv6-source-address/prefix-length>|any}

no <sequence-number>

Mode IPv6 Standard ACL Configuration

Default Any traffic controlled by a software ACL that does not explicitly match a filter is

denied.

Usage The filter entry will match on any IPv6 packet that has the specified IPv6 source

address and prefix length. The parameter any may be specified if an address does

not matter.

NOTE: Software ACLs will deny access unless explicitly permitted by an ACL action.

Examples To add an ACL filter entry with sequence number 5 that will deny any IPv6 packets

to the standard IPv6 access-list named my-list, enter the commands:

awplus# configure terminal

awplus(config)# ipv6 access-list standard my-list

awplus(config-ipv6-std-acl)# 5 deny any

Parameter Description

<sequence-number><1-65535>

The sequence number for the filter entry of the selected

access control list.

deny Specifies the packets to reject.

permit Specifies the packets to accept.

<ipv6-source-

address/prefix-

length>

IPv6 source address and prefix-length in the form X:X::X:X/P.

any Any IPv6 source host address.

613-50137-01 Rev A Command Reference for FS980M Series 847

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

(IPV6 ACCESS-LIST STANDARD FILTER)

To remove the ACL filter entry that will deny any IPv6 packets from the standard

IPv6 access-list named my-list, enter the commands:

awplus# configure terminal

awplus(config)# ipv6 access-list standard my-list

awplus(config-ipv6-std-acl)# no deny any

Alternately, to remove the ACL filter entry with sequence number 5 to the

standard IPv6 access-list named my-list, enter the commands:

awplus# configure terminal

awplus(config)# ipv6 access-list standard my-list

awplus(config-ipv6-std-acl)# no 5

Commands

ipv6 access-list standard (named)

show ipv6 access-list (IPv6 Software ACLs)

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 848

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

SHOW IPV6 ACCESS-LIST (IPV6 SOFTWARE ACLS)

show ipv6 access-list (IPv6 Software ACLs)

Overview Use this command to display all configured IPv6 access-lists or the IPv6 access-list

specified by name.

Syntax show ipv6 access-list [<access-list-name>]

show ipv6 access-list standard [<access-list-name>]

Mode User Exec and Privileged Exec

Example To show all configured IPv6 access-lists, use the following command:

awplus# show ipv6 access-list

Output Figure 26-1: Example output from show ipv6 access-list

Example To show the IPv6 access-list named deny_icmp, use the following command:

awplus# show ipv6 access-list deny_icmp

Output Figure 26-2: Example output from show ipv6 access-list for a named ACL

Commands

ipv6 access-list standard (named)

(ipv6 access-list standard filter)

Parameter Description

<access-list-name>Only display information about an IPv6 access-list with

the specified name.

standard Only display information about standard access-lists.



IPv6 access-list deny_icmp

deny icmp any any vlan 1



IPv6 access-list deny_ssh

deny tcp abcd::0/64 any eq 22



IPv6 access-list deny_icmp

deny icmp any any vlan 1

613-50137-01 Rev A Command Reference for FS980M Series 849

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

IPV6 SOFTWARE ACCESS CONTROL LIST (ACL) COMMANDS

VTY IPV6 ACCESS-CLASS (NAMED)

vty ipv6 access-class (named)

Overview For IPv6, use this command to set a standard named software access list to be the

management ACL. This is then applied to all available VTY lines for controlling

remote access by Telnet and SSH. This command allows or denies packets

containing the IPv6 addresses included in the ACL to create a connection to your

device.

ACLs that are attached using this command have an implicit ‘deny-all’ filter as the

final entry in the ACL. A typical configuration is to permit a specific address, or

range of addresses, and rely on the ‘deny-all’ filter to block all other access.

Use the no variant of this command to remove the access list.

Syntax vty ipv6 access-class <access-name>

no vty ipv6 access-class [<access-name>]

Mode Global Configuration

Examples To set the named standard access-list named access-ctrl to be the IPv6

management ACL, use the following commands:

awplus# configure terminal

awplus(config)# vty ipv6 access-class access-ctrl

To remove access-ctrl from the management ACL, use the following commands:

awplus# configure terminal

awplus(config)# no vty ipv6 access-class access-ctrl

Output Figure 26-3: Example output from the show running-config command

Commands

show running-config

vty access-class (numbered)

Parameter Description

<access-name> Specify an IPv6 standard software access-list name

awplus#showrunning-config|grep access-class



vty ipv6 access-class access-ctrl

613-50137-01 Rev A Command Reference for FS980M Series 850

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QoS Commands

Introduction

Overview This chapter provides an alphabetical reference for Quality of Service commands.

QoS uses ACLs. For more information about ACLs, see the ACL Feature Overview

and Configuration Guide.

Command List •“class” on page 852

•“class-map” on page 853

•“clear mls qos interface policer-counters” on page 854

•“default-action” on page 855

•“description (QoS policy-map)” on page 856

•“match access-group” on page 857

•“match cos” on page 859

•“match dscp” on page 860

•“match eth-format protocol” on page 861

•“match ip-precedence” on page 864

•“match mac-type” on page 865

•“match tcp-flags” on page 866

•“match vlan” on page 867

•“mls qos cos” on page 868

•“mls qos enable” on page 869

•“mls qos map cos-queue to” on page 870

•“mls qos map premark-dscp to” on page 871

•“no police” on page 872

•“police single-rate action” on page 873

613-50137-01 Rev A Command Reference for FS980M Series 851

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

•“police twin-rate action” on page 874

•“policy-map” on page 876

•“priority-queue” on page 877

•“remark-map” on page 878

•“remark new-cos” on page 880

•“service-policy input” on page 882

•“show class-map” on page 883

•“show mls qos” on page 884

•“show mls qos interface” on page 885

•“show mls qos interface policer-counters” on page 888

•“show mls qos interface queue-counters” on page 889

•“show mls qos interface storm-status” on page 890

•“show mls qos maps cos-queue” on page 891

•“show mls qos maps premark-dscp” on page 892

•“show platform classifier statistics utilization brief” on page 893

•“show policy-map” on page 894

•“storm-action” on page 895

•“storm-downtime” on page 896

•“storm-protection” on page 897

•“storm-rate” on page 898

•“storm-window” on page 899

•“trust dscp” on page 900

•“wrr-queue disable queues” on page 901

•“wrr-queue egress-rate-limit queues” on page 902

•“wrr-queue weight queues” on page 903

613-50137-01 Rev A Command Reference for FS980M Series 852

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

CLASS

class

Overview Use this command to associate an existing class-map to a policy or policy-map

(traffic classification), and to enter Policy Map Class Configuration mode to

configure the class- map.

Use the no variant of this command to delete an existing class-map.

If your class-map does not exist, you can create it by using the class-map

command.

Syntax class {<name>|default}

no class <name>

Mode Policy Map Configuration

Example The following example creates the policy-map pmap1(using the policy-map

command), then associates this to an already existing class-map named cmap1,

use the commands:

awplus# configure terminal

awplus(config)# policy-map pmap1

awplus(config-pmap)# class cmap1

awplus(config-pmap-c)#

Commands

class-map

policy-map

Parameter Description

<name>Name of the (already existing) class-map.

default Specify the default class-map.

613-50137-01 Rev A Command Reference for FS980M Series 853

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

CLASS-MAP

class-map

Overview Use this command to create a class-map.

Use the no variant of this command to delete the named class-map.

Syntax class-map <name>

no class-map <name>

Mode Global Configuration

Example This example creates a class-map called cmap1, use the commands:

awplus# configure terminal

awplus(config)# class-map cmap1

awplus(config-cmap)#

Parameter Description

<name>Name of the class-map to be created.

613-50137-01 Rev A Command Reference for FS980M Series 854

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

CLEAR MLS QOS INTERFACE POLICER-COUNTERS

clear mls qos interface policer-counters

Overview Resets an interface’s policer counters to zero. You can either clear a specific

class-map, or you can clear all class-maps by not specifying a class map.

Syntax clear mls qos interface <port> policer-counters [class-map

<class-map>]

Mode Privileged Exec

Example To reset the policy counters to zero for all class-maps for port1.0.1, use the

command:

awplus# clear mls qos interface port1.0.1 policer-counters

Commands

show mls qos interface policer-counters

Parameter Description

<port>The port may be a switch port (e.g. port1.0.4), a static

channel group (e.g. sa3), or a dynamic (LACP) channel group

(e.g. po4).

class-map Select a class-map.

<class-map>Class-map name.

613-50137-01 Rev A Command Reference for FS980M Series 855

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

DEFAULT-ACTION

default-action

Overview Sets the action for the default class-map belonging to a particular policy-map. The

action for a non-default class-map depends on the action of any ACL that is applied

to the policy-map.

The default action can therefore be thought of as specifying the action that will be

applied to any data that does not meet the criteria specified by the applied

matching commands.

Use the no variant of this command to reset to the default action of ‘permit’.

Syntax default-action [permit|deny|send-to-cpu]

no default-action

Default The default is ‘permit’.

Mode Policy Map Configuration

Examples To set the action for the default class-map to deny, use the command:

awplus(config-pmap)# default-action deny

Parameter Description

permit Packets to permit.

deny Packets to deny.

send-to-cpu Specify packets to send to the CPU.

613-50137-01 Rev A Command Reference for FS980M Series 856

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

DESCRIPTION (QOS POLICY-MAP)

description (QoS policy-map)

Overview Adds a textual description of the policy-map. This can be up to 80 characters long.

Use the no variant of this command to remove the current description from the

policy-map.

Syntax description <line>

no description

Mode Policy Map Configuration

Example To add the description, VOIP traffic, use the command:

awplus(config-pmap)# description VOIP traffic

Parameter Description

<line>Up to 80 character long line description.

613-50137-01 Rev A Command Reference for FS980M Series 857

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

MATCH ACCESS-GROUP

match access-group

Overview Use this command to apply an ACL to a class-map.

Use the no variant of this command to remove the match.

Syntax match access-group {<hw-IP-ACL>|<hw-MAC-ACL>|<hw-named-ACL>}

no match access-group

{<hw-IP-ACL>|<hw-MAC-ACL>|<hw-named-ACL>}

Mode Class Map

Usage First create an access-list that applies the appropriate action to matching packets.

Then use the match access-group command to apply this access-list as desired.

Note that this command will apply the access-list matching only to incoming data

packets.

Examples To configure a class-map named “cmap1”, which matches traffic against access-list

3001, which allows IP traffic from any source to any destination, use the

commands:

awplus# configure terminal

awplus(config)# access-list 3001 permit ip any any

awplus(config)# class-map cmap1

awplus(config-cmap)# match access-group 3001

To configure a class-map named “cmap2”, which matches traffic against access-list

4001, which allows MAC traffic from any source to any destination, use the

commands:

awplus# configure terminal

awplus(config)# access-list 4001 permit any any

awplus(config)# class-map cmap2

awplus(config-cmap)# match access-group 4001

Parameter Description

<hw-IP-ACL>Specify a hardware IP ACL number in the range <3000-3699>.

<hw-MAC-ACL>Specify a hardware MAC ACL number in the range <4000-4699>.

<hw-named-ACL>Specify a hardware named ACL (IP, IPv6 or MAC address entries).

613-50137-01 Rev A Command Reference for FS980M Series 858

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

MATCH ACCESS-GROUP

To configure a class-map named “cmap3”, which matches traffic against access-list

“hw_acl”, which allows IP traffic from any source to any destination, use the

commands:

awplus# configure terminal

awplus(config)# access-list hardware hw_acl

awplus(config-ip-hw-acl)# permit ip any any

awplus(config)# class-map cmap3

awplus(config-cmap)# match access-group hw_acl

Commands

class-map

613-50137-01 Rev A Command Reference for FS980M Series 859

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

MATCH COS

match cos

Overview Use this command to define a COS to match against incoming packets.

Use the no variant of this command to remove CoS.

Syntax match cos <0-7>

no match cos

Mode Class Map Configuration

Examples To set the class-map’s CoS to 4, use the commands:

awplus# configure terminal

awplus(config)# class-map cmap1

awplus(config-cmap)# match cos 4

To remove CoS from a class-map, use the commands:

awplus# configure terminal

awplus(config)# class-map cmap1

awplus(config-cmap)# no match cos

Parameter Description

<0-7>Specify the CoS value.

613-50137-01 Rev A Command Reference for FS980M Series 860

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

MATCH DSCP

match dscp

Overview Use this command to define the DSCP to match against incoming packets.

Use the no variant of this command to remove a previously defined DSCP.

Syntax match dscp <0-63>

no match dscp

Mode Class Map Configuration

Usage Use the match dscp command to define the match criterion after creating a

class-map.

Examples To configure a class-map named cmap1 with criterion that matches DSCP 56, use

the commands:

awplus# configure terminal

awplus(config)# class-map cmap1

awplus(config-cmap)# match dscp 56

To remove a previously defined DSCP from a class-map named cmap1, use the

commands:

awplus# configure terminal

awplus(config)# class-map cmap1

awplus(config-cmap)# no match dscp

Commands

class-map

Parameter Description

<0-63>Specify DSCP value (only one value can be specified).

613-50137-01 Rev A Command Reference for FS980M Series 861

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

MATCH ETH-FORMAT PROTOCOL

match eth-format protocol

Overview This command sets the Ethernet format and the protocol for a class-map to match

on.

Select one Layer 2 format and one Layer 3 protocol when you issue this command.

Use the no variant of this command to remove the configured Ethernet format and

protocol from a class-map.

Syntax match eth-format <layer-two-format> protocol

<layer-three-protocol>

no match eth-format protocol

Parameter Description

<layer-two-formats>

ethii-tagged EthII Tagged Packets (enter the parameter name).

ethii-untagged EthII Untagged Packets (enter the parameter name).

ethii-any EthII Tagged or Untagged Packets (enter the parameter

name).

<layer-three-protocols>

<word> A Valid Protocol Number in hexidecimal.

any Note that the parameter “any” is only valid when used

with the netwarerawtagged and netwarerawuntagged

protocol options.

sna-path-control Protocol Number 04 (enter the parameter name or its

number).

proway-lan Protocol Number 0E (enter the parameter name or its

number).

eia-rs Protocol Number 4E (enter the parameter name or its number).

proway Protocol Number 8E (enter the parameter name or its number).

ipx-802dot2 Protocol Number E0 (enter the parameter name or its

number).

netbeui Protocol Number F0 (enter the parameter name or its

number).

iso-clns-is Protocol Number FE (enter the parameter name or its

number).

xdot75-internet Protocol Number 0801(enter the parameter name or its

number).

nbs-internet Protocol Number 0802 (enter the parameter name or its

number).

613-50137-01 Rev A Command Reference for FS980M Series 862

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

MATCH ETH-FORMAT PROTOCOL

ecma-internet Protocol Number 0803 (enter the parameter name or its

number).

chaosnet Protocol Number 0804 (enter the parameter name or its

number).

xdot25-level-3 Protocol Number 0805 (enter the parameter name or its

number).

arp Protocol Number 0806 (enter the parameter name or its

number).

xns-compat Protocol Number 0807 (enter the parameter name or its

number).

banyan-systems Protocol Number 0BAD (enter the parameter name or

its number).

bbn-simnet Protocol Number 5208 (enter the parameter name or its

number).

dec-mop-dump-ld Protocol Number 6001 (enter the parameter name or its

number).

dec-mop-rem-

cdons

Protocol Number 6002 (enter the parameter name or its

number).

dec-decnet Protocol Number 6003 (enter the parameter name or its

number).

dec-lat Protocol Number 6004 (enter the parameter name or its

number).

dec-diagnostic Protocol Number 6005 (enter the parameter name or its

number).

dec-customer Protocol Number 6006 (enter the parameter name or its

number).

dec-lavc Protocol Number 6007 (enter the parameter name or its

number).

rarp Protocol Number 8035 (enter the parameter name or its

number).

dec-lanbridge Protocol Number 8038 (enter the parameter name or its

number).

dec-encryption Protocol Number 803D (enter the parameter name or

its number).

appletalk Protocol Number 809B (enter the parameter name or its

number).

ibm-sna Protocol Number 80D5 (enter the parameter name or

its number).

appletalk-aarp Protocol Number 80F3 (enter the parameter name or its

number).

snmp Protocol Number 814CV.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 863

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

MATCH ETH-FORMAT PROTOCOL

Mode Class Map Configuration

Examples To set the eth-format to ethii-tagged and the protocol to 0800 (IP) for class-map

cmap1, use the commands:

awplus# configure terminal

awplus(config)# class-map cmap1

awplus(config-cmap)# match eth-format ethii-tagged protocol

0800

awplus#

awplus(config-cmap)# match eth-format ethii-tagged protocol ip

To remove the eth-format and the protocol from the class-map cmap1, use the

commands:

awplus# configure terminal

awplus(config)# class-map cmap1

awplus(config-cmap)# no match eth-format protocol

ethertalk-2 Protocol Number 809B (enter the parameter name or its

number).

ethertalk-2-aarp Protocol Number 80F3 (enter the parameter name or its

number).

ipx-snap Protocol Number 8137 (enter the parameter name or its

number).

ipx-802dot3 Protocol Number FFFF (enter the parameter name or its

number).

ip Protocol Number 0800 (enter the parameter name or its

number).

ipx Protocol Number 8137 (enter the parameter name or its

number).

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 864

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

MATCH IP-PRECEDENCE

match ip-precedence

Overview Use this command to identify IP precedence values as match criteria.

Use the no variant of this command to remove IP precedence values from a

class-map.

Syntax match ip-precedence <0-7>

no match ip-precedence

Mode Class Map Configuration

Example To configure a class-map named cmap1 to match all IPv4 packets with a

precedence value of 5, use the commands:

awplus# configure terminal

awplus(config)# class-map cmap1

awplus(config-cmap)# match ip-precedence 5

Parameter Description

<0-7>The precedence value to be matched.

613-50137-01 Rev A Command Reference for FS980M Series 865

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

MATCH MAC-TYPE

match mac-type

Overview Use this command to set the MAC type for a class-map to match on.

Use no variant of this command to remove the MAC type match entry.

Syntax match mac-type {l2bcast|l2mcast|l2ucast}

no match mac-type

Mode Class Map Configuration

Examples To set the class-map’s MAC type to Layer 2 multicast, use the commands:

awplus# configure terminal

awplus(config)# class-map cmap1

awplus(config-cmap)# match mac-type l2mcast

To remove the class-map’s MAC type entry, use the commands:

awplus# configure terminal

awplus(config)# class-map cmap1

awplus(config-cmap)# no match mac-type

Parameter Description

l2bcast Layer 2 Broadcast traffic.

l2mcast Layer 2 Multicast traffic.

l2ucast Layer 2 Unicast traffic.

613-50137-01 Rev A Command Reference for FS980M Series 866

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

MATCH TCP-FLAGS

match tcp-flags

Overview Sets one or more TCP flags (control bits) for a class-map to match on.

Use the no variant of this command to remove one or more TCP flags for a

class-map to match on.

Syntax match tcp-flags {[ack][fin][psh][rst][syn][urg]}

no match tcp-flags {[ack][fin][psh][rst][syn][urg]}

Mode Class Map Configuration

Examples To set the class-map’s TCP flags to ack and syn, use the commands:

awplus# configure terminal

awplus(config)# class-map

awplus(config-cmap)# match tcp-flags ack syn

To remove the TCP flags ack and rst, use the commands:

awplus# configure terminal

awplus(config)# class-map

awplus(config-cmap)# no match tcp-flags ack rst

Parameter Description

ack Acknowledge.

fin Finish.

psh Push

rst Reset.

syn Synchronize.

urg Urgent.

613-50137-01 Rev A Command Reference for FS980M Series 867

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

MATCH VLAN

match vlan

Overview Use this command to define the VLAN ID as match criteria.

Use the no variant of this command to disable the VLAN ID used as match criteria.

Syntax match vlan <1-4094>

no match vlan

Mode Class Map Configuration

Examples To configure a class-map named cmap1 to include traffic from VLAN 3, use the

commands:

awplus# configure terminal

awplus(config)# class-map cmap1

awplus(config-cmap)# match vlan 3

To disable the configured VLAN ID as a match criteria for the class-map named

cmap1, use the commands:

awplus# configure terminal

awplus(config)# class-map cmap1

awplus(config-cmap)# no match vlan

Parameter Description

<1-4094>The VLAN number.

613-50137-01 Rev A Command Reference for FS980M Series 868

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

MLS QOS COS

mls qos cos

Overview This command assigns a CoS (Class of Service) user-priority value to untagged

frames entering a specified interface. By default, all untagged frames are assigned

a CoS value of 0.

Use the no variant of this command to return the interface to the default CoS

setting for untagged frames entering the interface.

Syntax mls qos cos <0-7>

no mls qos cos

Default By default, all untagged frames are assigned a CoS value of 0. Note that for tagged

frames, the default behavior is not to alter the CoS value.

Mode Interface Configuration

Example To assign a CoS user priority value of 2 to all untagged packets entering ports 1.0.1

to 1.0.6, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.1-port1.0.6

awplus(config-if)# mls qos cos 2

Parameter Description

<0-7>The Class of Service, user-priority value.

613-50137-01 Rev A Command Reference for FS980M Series 869

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

MLS QOS ENABLE

mls qos enable

Overview Use this command to globally enable QoS on the switch or stack.

Use the no variant of this command to globally disable QoS and remove all QoS

configuration. The no variant of this command removes all class-maps,

policy-maps, and policers that have been created. Running the no mls qos

command will therefore remove all pre-existing QoS configurations on the switch.

Mode Global Configuration

Syntax mls qos enable

no mls qos

Example To enable QoS on the switch, use the commands:

awplus# configure terminal

awplus(config)# mls qos enable

613-50137-01 Rev A Command Reference for FS980M Series 870

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

MLS QOS MAP COS-QUEUE TO

mls qos map cos-queue to

Overview Use this command to set the default CoS to egress queue mapping. This is the

default queue mapping for packets that do not get assigned an egress queue via

any other QoS functionality.

Use the no variant of this command to reset the cos-queue map back to its default

setting. The default mappings for this command are:

Syntax mls qos map cos-queue <cos-priority> to <queue-number>

no mls qos map cos-queue

Mode Global Configuration

Examples To map CoS 2 to queue 0, use the command:

awplus# configure terminal

awplus(config)# mls qos map cos-queue 2 to 0

To set the cos-queue map back to its defaults, use the command:

awplus# configure terminal

awplus(config)# no mls qos map cos-queue

Commands

show mls qos interface

CoS Priority : 0 1 2 3 4 5 6 7

-----------------------------------

CoS QUEUE: 2 0 1 3 4 5 6 7

Parameter Description

<cos-priority>CoS priority value. Can take a value between 0 and 7.

<queue-number>Queue number. Can take a value between 0 and 7.

613-50137-01 Rev A Command Reference for FS980M Series 871

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

MLS QOS MAP PREMARK-DSCP TO

mls qos map premark-dscp to

Overview This command configures the premark-dscp map. It is used when traffic is

classified by a class-map that has trust dscp configured. Based on a lookup DSCP,

the map determines new QoS settings for the traffic.

The no variant of this command resets the premark-dscp map to its defaults. If no

DSCP is specified then all DSCP entries will be reset to their defaults.

Syntax mls qos map premark-dscp <0-63> to [new-queue <0-4>]

no mls qos map premark-dscp [<0-63>]

Mode Global Configuration

Usage With the trust dscp command set, the mls qos map premark-dscp command

enables you to specify the queue for packets.

When trust dscp is enabled on a port, the switch cannot use the CoS (802.1p

priority) value to determine queue settings for traffic egressing that port.

Therefore, non-IP packets will not be prioritized on that port. Non-IP packets will all

go into queue 0.

Example To send packets to queue 2 if they have a DSCP of 34, use the commands:

awplus# configure terminal

awplus(config)# mls qos map premark-dscp 34 to new-queue 2

Example To reset the entry for DSCP 1 use the command:

awplus# configure terminal

awplus(config)# no mls qos map premark-dscp 1

Commands

show mls qos maps premark-dscp

trust dscp

Parameter Description

premark-dscp <0-63>The DSCP value on ingress.

new-queue <0-3>Modify Egress Queue.

613-50137-01 Rev A Command Reference for FS980M Series 872

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

NO POLICE

no police

Overview Use this command to disable any policer previously configured on the class-map.

Syntax no police

Mode Policy Map Class Configuration

Usage This command disables any policer previously configured on the class-map.

Example To disable policing on a class-map use the command:

awplus# configure terminal

awplus(config)# policy-map name

awplus(config-pmap)# class classname

awplus(config-pmap-c)# no police

Commands

police single-rate action

police twin-rate action

613-50137-01 Rev A Command Reference for FS980M Series 873

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

POLICE SINGLE-RATE ACTION

police single-rate action

Overview Configures a single-rate policer for a class-map.

Syntax police single-rate <rate> <number> <number> action drop-red

Mode Policy Map Class Configuration

Usage You can use a policer to meter the traffic on a port and drop non-conforming (red)

packets.

Example To configure a single rate meter measuring traffic of 10 Mbps that drops a

sustained burst of traffic over this rate, use the commands:

awplus# configure terminal

awplus(config)# policy-map name

awplus(config-pmap)# class classname

awplus(config-pmap-c)# police single-rate 10000 1875000 1875000

action drop-red

Commands

no police

Parameter Description

<rate>Specify the maximum rate (1-16000000 kbps).

<number>Specify any decimal number between 0 and 16777216. The switch

ignores these values.

action Specify the action if the rate is exceeded.

drop-red Drop the red packets.

613-50137-01 Rev A Command Reference for FS980M Series 874

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

POLICE TWIN-RATE ACTION

police twin-rate action

Overview Configures a twin-rate policer for a class-map.

Syntax police twin-rate <cir> <pir> <cbs> <pbs> action

{drop-red|remark-transmit}

Mode Policy Map Class Configuration

Usage A policer can be used to meter the traffic classified by the class-map and as a result

will be given one of three bandwidth classes. These are green (conforming), yellow

(partially- conforming), and red (non-conforming).

A twin-rate policer is based on four values. These are the minimum rate (CIR),

minimum burst size (CBS), maximum rate (PIR), and maximum burst size (PBS). The

following table shows how these values define the bandwidth classes.

Using an action of drop-red means that any packets classed as red will be

discarded.

Parameter Description

<cir>Specify the Committed Information Rate (CIR) (1-40000000 kbps).

<pir>Specify the Peak Information Rate (PIR) (1-40000000 kbps).

<cbs>Specify the Committed Burst Size (CBS) (0-16777216 bytes).

<pbs>Specify the Peak Burst Size (PBS) (0-16777216 bytes).

action Specify the action if rate is exceeded.

drop-red Drop the red packets.

remark-transmit Modify the packets using the remark map, then

transmit. You can configure the remark map

using the remark-map command.

Bandwidth

Class Definition

green The sum of the number of existing (buffered) bytes plus those arriving

at the port per unit time results in a value that is less than that set for

the CBS.

yellow The sum of the number of existing (buffered) bytes plus those arriving

at the port per unit time results in a value that is between those set for

the CBS and the PBS.

red The sum of the number of existing (buffered) bytes plus those arriving

at the port per unit time results in a value that exceeds that set for the

PBS.

613-50137-01 Rev A Command Reference for FS980M Series 875

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

POLICE TWIN-RATE ACTION

Using an action of remark-transmit means that the packet will be remarked with

the values configured in the policed-dscp map. The index into this map is

determined by the DSCP in the packet.

Note that the remark-map does not only apply to red traffic. If a remark-map is

configured on the same class-map as the policer, then the remark-map will apply

to green- colored and yellow-colored traffic irrespective of the value configured on

the action parameter of the policer. So, even if action is configured to drop-red,

the remark-map will be applied to green and yellow traffic. So, the action

parameter only applies to red- colored traffic. If action is set to drop-red, then red

traffic is dropped; if action is set to remark-transmit, then the red traffic has the

action of the remark map applied to it, and is then transmitted.

Example To configure a twin rate meter measuring a minimum rate of 10 Mbps and a

maximum rate of 20 Mbps that uses the premark map to remark any

non-conforming traffic, use the commands:

awplus# configure terminal

awplus(config)# policy-map name

awplus(config-pmap)# class classname

awplus(config-pmap-c)# police twin-rate 10000 20000 1875000

3750000 action remark-transmit

Commands

no police

police single-rate action

613-50137-01 Rev A Command Reference for FS980M Series 876

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

POLICY-MAP

policy-map

Overview Use this command to create a policy-map and to enter Policy Map Configuration

mode to configure the specified policy-map.

Use the no variant of this command to delete an existing policy-map.

Syntax policy-map <name>

no policy-map <name>

Mode Global Configuration

Example To create a policy-map called pmap1, use the commands:

awplus# configure terminal

awplus(config)# policy-map pmap1

awplus(config-pmap)#

Commands

class-map

Parameter Description

<name>Name of the policy-map.

613-50137-01 Rev A Command Reference for FS980M Series 877

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

PRIORITY-QUEUE

priority-queue

Overview Configures strict priority based scheduling on the specified egress queues. You

must specify at least one queue.

Syntax priority-queue [0][1][2][3][4][5][6][7]

Mode Interface Configuration.

Usage

By default, the queues on all ports are set for priority queuing. You can change the

queue emptying sequence to weighted round robin, by using the wrr-queue

weight queues command. You can then use the priority-queue command to reset

the selected queues to priority queuing.

Note that the emptying sequence for priority queuing is always highest queue

number to lowest queue number.

Example To apply priority based scheduling to egress queues 1 and 2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.1

awplus(config-if)# priority-queue 1 2

Commands

show mls qos interface

wrr-queue weight queues

Parameter Description

[0][1]...[7] Specify the queues that will use strict priority scheduling. With

strict priority scheduling, the switch will completely empty the

highest numbered queue first, then start processing the next

lowest numbered queue.

awplus(config-if)#wrr-queue weight 2 queues 0

% Queue weight changed for all ports

% All egress queues set to WRR scheduling

613-50137-01 Rev A Command Reference for FS980M Series 878

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

REMARK-MAP

remark-map

Overview Use this command to configure the remark map. If a re-mark map is applied to a

class, and a policer is also applied to the same class, then:

• green and yellow traffic will all be acted upon by the remark-map, and

• red traffic will be either dropped or acted upon by the remark-map,

depending on whether the policer action is set to drop-red or

remark-transmit.

The no variant of this command resets the remark map to its defaults. Specifying

the bandwidth class is optional. If no bandwidth class is specified, then all

bandwidth classes are reset to their defaults.

Syntax remark-map [bandwidth-class {green|yellow|red}] to {[new-dscp

<0-63>] [new-bandwidth-class {green|yellow|red}]}

no remark-map [bandwidth-class {green|yellow|red}] to

{[new-dscp <0-63>] [new-bandwidth-class {green|yellow|red}]}

Mode Policy Map Class Configuration

Examples To remark the policed green traffic to a new DSCP of 2 and a new bandwidth class

of yellow, use the commands:

awplus# configure terminal

awplus(config)# policy-map pmap1

awplus(config-pmap)# class cmap1

awplus(config-pmap-c)# remark-map bandwidth-class green to

new-dscp 2 new-bandwidth-class yellow

To remark the policed green traffic to a new DSCP of 2, use the commands:

awplus# configure terminal

awplus(config)# policy-map pmap1

awplus(config-pmap)# class cmap1

awplus(config-pmap-c)# remark-map bandwidth-class green to

new-dscp 2

Parameter Description

bandwidth-class Specify the bandwidth class of packets to remark.

green Remark green packets.

yellow Remark yellow packets.

red Remark red packets.

new-dscp Specify the new DSCP value.

<0-63>The DSCP value.

613-50137-01 Rev A Command Reference for FS980M Series 879

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

REMARK-MAP

To reset the DSCP for all bandwidth classes, use the commands:

awplus# configure terminal

awplus(config)# policy-map pmap1

awplus(config-pmap)# class cmap1

awplus(config-pmap-c)# no remark-map to new-dscp

Commands

police single-rate action

police twin-rate action

613-50137-01 Rev A Command Reference for FS980M Series 880

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

REMARK NEW-COS

remark new-cos

Overview This command enables you to configure and remark either or both of:

• the CoS flag in the data packet

• the input into the CoS to queue map, thus changing the destination egress

queue.

Syntax remark new-cos <0-7> [internal|external|both]

no remark new-cos [internal|external|both]

Mode Policy Map Class Configuration

Usage The default CoS to Queue mappings are shown in the following table:

The relationship between this command and the CoS to queue map is shown in

the following figure.

Parameter Description

<0-7>The new value for the CoS flag and/or the input into the CoS to queue

map.

external Remarks the CoS flag in the packet.

internal Remarks the new-CoS input into the CoS to queue map.

both Remarks (with the same value) both the CoS flag in the packet and the

input to the CoS to queue map.

CoS Value 01234567

Egress Queue No 20134567

613-50137-01 Rev A Command Reference for FS980M Series 881

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

REMARK NEW-COS

Figure 27-1: Remarking and the CoS to Q map

Example For policy-map “pmap3” and class-map “cmap1”, set the CoS value to 2 and also set

the input to the CoS to queue map so that the traffic is assigned to egress queue 1:

awplus# configure terminal

awplus(config)# policy-map pmap3

awplus(config-pmap)# class cmap1

awplus(config-pmap-c)# remark new-cos 2 both

Commands

mls qos map cos-queue to

show mls qos maps cos-queue

4HEABOVEMAPPINGISSETBYTHECOMMAND MLSQOSMAPCOSQUEUETOANDDISPLAYEDBYTHECOMMAND

SHOWMLSQOSMAPSCOSQUEUE7ITHTHE REMARKNEWCOSCOMMANDUNSETORSETTOEXTERNALTHEQUEUEMAPPING

TAKESITSINPUTFROMTHE%XISTING#O3VALUE7ITHTHE REMARKNEWCOSCOMMANDSETTOINTERNALORBOTHTHE

QUEUEMAPPINGTAKESITSINPUTFROMTHEVALUESETBYTHECOMMAND REMARKNEWCOS.OTETHATALTHOUGHTHE

#O3TO1UEUEMAPAPPLIESTOTHEWHOLESWITCHTHEREMARKNEWCOSCOMMANDAPPLIESPERINDIVIDUALCLASSMAP

%XISTING#O3VALUE

.EW#O3INTERNAL

%GRESSQUEUE

VALUE

#O36ALUE

%GRESS1UEUE



 

1O3??1?-AP?"

#OSTO1UEUE

-APPING

2EMARKNEWCOSEXTERNAL

#O3&LAGIN0ACKET

2EMARKNEWCOSBOTH

2EMARKNEWCOSINTERNAL

Table 27-1: CoS to egress queue remarking function

Input Command Output

CoS field = 1 Remark new-cos (not

configured)

CoS value = 1

Packet sent to egress queue 0

CoS field = 1 Remark new-cos 2 external CoS value = 2

Packet sent to egress queue 0

CoS set to 1 Remark new-cos 2 internal CoS value = 1

Packet sent to egress queue 1

CoS set to 1 Remark new-cos 2 both CoS value = 2

Packet sent to egress queue 1

Note: This table assumes that the CoS to Queue map is set to its default values.

613-50137-01 Rev A Command Reference for FS980M Series 882

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

SERVICE-POLICY INPUT

service-policy input

Overview Use this command to apply a policy-map to the input of an interface.

Use the no variant of this command to remove a policy-map and interface

association.

Syntax service-policy input <policy-map>

no service-policy input <policy-map>

Mode Interface Configuration

Usage This command can be applied to switch ports or static channel groups, but not to

dynamic (LACP) channel groups.

Example To apply a policy-map named pmap1 to interface port1.0.2, use the

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# service-policy input pmap1

Parameter Description

<policy-map>Policy map name that will be applied to the input.

613-50137-01 Rev A Command Reference for FS980M Series 883

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

SHOW CLASS-MAP

show class-map

Overview Use this command to display the QoS class-maps’ criteria for classifying traffic.

Syntax show class-map [<class-map-name>]

Mode User Exec and Privileged Exec

Example To display a QoS class-map’s match criteria for classifying traffic, use the command:

awplus# show class-map cmap1

Output Figure 27-2: Example output from the show class-map command

Commands

class-map

Parameter Description

<class-map-name> Name of the class-map.

awplus#show class-map



CLASS-MAP-NAME: myClass

Match Mac Type: 2 l2mcast



CLASS-MAP-NAME: default

613-50137-01 Rev A Command Reference for FS980M Series 884

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

SHOW MLS QOS

show mls qos

Overview Use this command to display whether QoS is enabled or disabled on the switch.

Syntax show mls qos

Mode User Exec and Privileged Exec

Example To display whether QoS is enabled or disabled, use the command:

awplus# show mls qos

Output Figure 27-3: Example output from the show mls qos command

Commands

mls qos enable

awplus#show mls qos

Enable

613-50137-01 Rev A Command Reference for FS980M Series 885

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

SHOW MLS QOS INTERFACE

show mls qos interface

Overview Displays the current settings for the interface. This includes its default CoS and

queue, scheduling used for each queue, and any policies/maps that are attached.

Syntax show mls qos interface [<port>]

Mode User Exec and Privileged Exec

Example To display current CoS and queue settings for interface port1.0.1, use the

command:

awplus# show mls qos interface port1.0.1

Output Figure 27-4: Example output from the show mls qos interface command

Parameter Description

<port>Switch port.

Default CoS: 7

Default Queue: 7

Number of egress queues: 8

Queue Set: 1



Egress Queue: 0

Status: Enabled

Scheduler: Strict Priority

Queue Limit: 12%

Egress Rate Limit: 0 Kb



Egress Queue: 1

Status: Enabled

Scheduler: Strict Priority

Queue Limit: 12%

Egress Rate Limit: 0 Kb

613-50137-01 Rev A Command Reference for FS980M Series 886

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

SHOW MLS QOS INTERFACE

Egress Queue: 2

Status: Enabled

Scheduler: Strict Priority

Queue Limit: 12%

Egress Rate Limit: 0 Kb

Egress Queue: 3

Status: Enabled

Scheduler: Wrr Group 2

Weight: 10

Queue Limit: 12%

Egress Rate Limit: 0 Kb

Egress Queue: 4

Status: Enabled

Scheduler: Wrr Group 1

Weight: 10

Queue Limit: 12%

Egress Rate Limit: 0 Kb

Egress Queue: 5

Status: Enabled

Scheduler: Strict Priority

Queue Limit: 12%

Egress Rate Limit: 0 Kb

Egress Queue: 6

Status: Enabled

Scheduler: Strict Priority

Queue Limit: 12%

Egress Rate Limit: 0 Kb

Egress Queue: 7

Status: Enabled

Scheduler: Strict Priority

Queue Limit: 12%

Egress Rate Limit: 0 Kb

Table 28: Parameters in the output of the show mls qos interface command

Parameter Description

Default CoS The default CoS priority that will be applied to all packets

arriving on this interface.

Default Queue The default queue that will be applied to all packets

arriving on this interface.

Number of egress

queues

The total number of egress queues available on this

interface.

Egress Queue X Number of this egress queue.

Status Queue can either be enabled or disabled.

Scheduler The scheduling mode being used for servicing the

transmission of packets on this port.

613-50137-01 Rev A Command Reference for FS980M Series 887

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

SHOW MLS QOS INTERFACE

Queue Limit The percentage of the port’s buffers that have been

allocated to this queue.

Egress Rate Limit The amount of traffic that can be transmitted via this

queue per second. 0 Kb means there is currently no

rate-limiting enabled.

Table 28: Parameters in the output of the show mls qos interface command

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 888

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

SHOW MLS QOS INTERFACE POLICER-COUNTERS

show mls qos interface policer-counters

Overview This command displays an interface’s policer counters. This can either be for a

specific class-map or for all class-maps attached to the interface. If no class-map is

specified then all class-map policer counters attached to the interface are

displayed.

Syntax show mls qos interface <port> policer-counters [class-map

<class-map>]

Mode User Exec and Privileged Exec

Usage Note that:

• The counters are based on metering performed on the specified class-map.

Therefore, the ‘Dropped Bytes’ counter is the number of bytes dropped due

to metering. This is different from packets dropped via a ‘deny’ action in the

ACL. If a policer is configured to perform re-marking, bytes can be marked

Red but are not dropped, and is shown with a value of 0 for the Dropped field

and a non-0 value for the ‘Red Bytes’ field.

Example To show the counters for all class-maps attached to port1.0.1, use the command:

awplus# show mls qos interface port1.0.1 policer-counters

Output Figure 27-5: Example output from show mls qos interface policer-counters

This output shows a policer configured with remarking through ‘action remark-

transmit’, so although bytes are marked as Red, none are dropped. Therefore, the

‘Non-dropped Bytes’ field shows a summation of Green/Yellow and Red bytes.

awplus#show mls qos int port1.0.1 policer-counters 

Interface: port1.0.1

Class-map: default

Green/Yellow Bytes: 0

Red Bytes: 0

Dropped Bytes: 0

Non-dropped Bytes: 0

Class-map: cmap1

Green/Yellow Bytes: 1629056

Red Bytes: 7003200

Dropped Bytes: 0

Non-dropped Bytes: 8632256

613-50137-01 Rev A Command Reference for FS980M Series 889

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

SHOW MLS QOS INTERFACE QUEUE-COUNTERS

show mls qos interface queue-counters

Overview This command displays an interface’s egress queue counters. This can either be for

a specific queue or for all queues on the interface. If no queue is specified all queue

counters on the interface will be displayed.

The counters show the number of frames currently in the queue and the maximum

number of frames allowed in the queue, for individual egress queues and the port’s

queue (which will be a sum of all egress queues).

Syntax show mls qos interface <port> queue-counters [queue <number>]

Mode User Exec and Privileged Exec

Example To show the counters for all queues on port1.0.1, use the command:

awplus# show mls qos interface port1.0.1 queue-counters

Output Figure 27-6: Example output from the show mls qos interface queue-counters

command



Interface port1.0.4 Queue Counters:

Port queue length 1169

Egress Queue length:

Queue 0 0

Queue 1 0

Queue 2 1169

Queue 3 0

Queue 4 0

Queue 5 0

Queue 6 0

Queue 7 0

Table 29: Parameters in the output of the show mls qos interface

queue-counters command

Parameter Description

Interface Port we are showing the counters for.

Port queue length Number of frames in the port’s queue. This will be the

sum of all egress queues on the port.

Egress Queue length Number of frames in a specific egress queue.

613-50137-01 Rev A Command Reference for FS980M Series 890

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

SHOW MLS QOS INTERFACE STORM-STATUS

show mls qos interface storm-status

Overview Show the current configuration and status of the QoS Storm Protection (QSP) on

the given port.

Syntax show mls qos interface <port> storm-status

Mode User Exec and Privileged Exec

Example To see the QSP status on port1.0.1, use the command:

awplus# show mls qos interface port1.0.1 storm-status

Output Figure 27-7: Example output from the show mls qos interface storm-status

command

Commands

storm-action

storm-downtime

storm-protection

storm-rate

storm-window

Parameter Description

<port>Switch port.

Interface: port1.0.1

Storm-Protection: Enabled

Port-status: Enabled

Storm Action: vlandisable

Storm Window: 5000 ms

Storm Downtime: 0 s

Timeout Remaining: 0 s

Last read data-rate: 0 kbps

Storm Rate: 1000 kbps

613-50137-01 Rev A Command Reference for FS980M Series 891

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

SHOW MLS QOS MAPS COS-QUEUE

show mls qos maps cos-queue

Overview Show the current configuration of the cos-queue map.

Syntax show mls qos maps cos-queue

Mode User Exec and Privileged Exec

Example To display the current configuration of the cos-queue map, use the command:

awplus# show mls qos maps cos-queue

Output Figure 27-8: Example output from show mls qos maps cos-queue

Commands

mls qos map cos-queue to

COS-TO-QUEUE-MAP:

COS : 0 1 2 3 4 5 6 7

-----------------------------------

QUEUE: 2 0 1 3 4 5 6 7

613-50137-01 Rev A Command Reference for FS980M Series 892

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

SHOW MLS QOS MAPS PREMARK-DSCP

show mls qos maps premark-dscp

Overview This command displays the premark-dscp map. This map is used to determine the

queue on the basis of the DSCP.

Syntax show mls qos maps premark-dscp [<0-63>]

Mode User Exec and Privileged Exec

Example To display the premark-dscp map for DSCP 1, use the command:

awplus# show mls qos maps premark-dscp 1

Output Figure 27-9: Example output from the show mls qos maps premark-dscp

command

Commands

mls qos map premark-dscp to

Parameter Description

<0-63>DSCP table entry.

awplus#show mls qos maps premark-dscp 63

PREMARK-DSCP-MAP:



DSCP 1

--------------------------------

New queue 2

613-50137-01 Rev A Command Reference for FS980M Series 893

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

SHOW PLATFORM CLASSIFIER STATISTICS UTILIZATION BRIEF

show platform classifier statistics utilization

brief

Overview This command displays the number of used entries available for various platform

functions, and the percentage that number of entries represents of the total

available.

Syntax show platform classifier statistics utilization brief

Mode Privileged Exec

Example To display the platform classifier utilization statistics, use the following command:

awplus# show platform classifier statistics utilization brief

Output Figure 27-10: Output from the show platform classifier statistics utilization

brief command

Commands

show platform

awplus#show platform classifier statistics utilization brief



[Instance 4]

Number of Entries:

Policy Type Group ID Used / Total

----------------------------------------------

ACL 1476395010 0 / 245 ( 0%)

DoS Inactive 0 / 0 ( 0%)

VLAN Counter

Group-Octet Inactive 0 / 0 ( 0%)

Group-Packet Inactive 0 / 0 ( 0%)

QoS 0 / 768 ( 0%)

613-50137-01 Rev A Command Reference for FS980M Series 894

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

SHOW POLICY-MAP

show policy-map

Overview Displays the policy-maps configured on the switch. The output also shows

whether or not they are connected to a port (attached / detached) and shows their

associated class-maps.

Syntax show policy-map [<name>]

Mode User Exec and Privileged Exec

Example To display a listing of the policy-maps configured on the switch, use the command:

awplus# show policy-map

Output Figure 27-11: Example output from the show policy-map command

Commands

service-policy input

Parameter Description

<name>The name of a specific policy-map.

awplus#show policy-map



POLICY-MAP-NAME: myPolicy

State: attached

Default class-map action: permit 



CLASS-MAP-NAME: default

Policer counters enabled



CLASS-MAP-NAME: myClass

Match Mac Type: 2 l2mcast

Policer counters enabled

Remark CoS and CoS-Queue Map Index to 6

613-50137-01 Rev A Command Reference for FS980M Series 895

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

STORM-ACTION

storm-action

Overview Sets the action to be taken when triggered by QoS Storm Protection (QSP). There

are three available options:

•portdisable will disable the port in software.

•vlandisable will disable the port from the VLAN matched by the class-map

in class-map. This option requires the match vlan class-map to be present in

the class-map

•linkdown will physically bring the port down. .

The no variant of this command will negate the action set by the storm-action

command.

Syntax storm-action {portdisable|vlandisable|linkdown}

no storm-action

Mode Policy Map Class Configuration

Examples To apply the storm protection of vlandisable to the policy-map named “pmap2”

and the class-map named “cmap1”, use the following commands:

awplus# configure terminal

awplus(config)# policy-map pmap2

awplus(config-pmap)# class cmap1

awplus(config-pmap-c# storm-action vlandisable

To negate the storm protection set on the policy-map named “pmap2” and the

class-map named “cmap1”, use the following commands:

awplus# configure terminal

awplus(config)# policy-map pmap2

awplus(config-pmap)# class cmap1

awplus(config-pmap-c# no storm-action

Commands

storm-downtime

storm-protection

storm-rate

storm-window

Parameter Description

portdisable Disable the port in software.

vlandisable Disable the VLAN.

linkdown Shutdown the port physically.

613-50137-01 Rev A Command Reference for FS980M Series 896

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

STORM-DOWNTIME

storm-downtime

Overview Sets the time to re-enable a port that has been disabled by QoS Storm Protection

(QSP). The time is given in seconds, from a minimum of one second to maximum

of 86400 seconds (i.e. one day).

The no variant of this command resets the time to the default value of 10 seconds.

Syntax storm-downtime <1-86400>

no storm-downtime

Default 10 seconds

Mode Policy Map Class Configuration

Examples To re-enable the port in 1 minute, use the following commands:

awplus# configure terminal

awplus(config)# policy-map pmap2

awplus(config-pmap)# class cmap1

awplus(config-pmap-c)# storm-downtime 60

To re-set the port to the default (10 seconds), use the following commands:

awplus# configure terminal

awplus(config)# policy-map pmap2

awplus(config-pmap)# class cmap1

awplus(config-pmap-c)# no storm-downtime

Commands

storm-action

storm-protection

storm-rate

storm-window

Parameter Description

<1-86400>Seconds.

613-50137-01 Rev A Command Reference for FS980M Series 897

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

STORM-PROTECTION

storm-protection

Overview Use this command to enable Policy Based Storm Protection (such as QSP - QoS

Storm Protection). Storm protection is activated as soon as a port is enabled.

However, it will only be functional after storm-rate and storm-window have been

set.

The no variant of this command disables Policy Based Storm Protection.

Syntax storm-protection

no storm-protection

Default By default, storm protection is disabled.

Mode Policy Map Class Configuration

Examples To enable QSP on cmap2 in pmap2, use the following commands:

awplus# configure terminal

awplus(config)# policy-map pmap2

awplus(config-pmap)# class cmap2

awplus(config-pmap-c)# storm-protection

To disable QSP on cmap2 in pmap2, use the following commands:

awplus# policy-map pmap2

awplus(config-pmap)# class cmap2

awplus(config-pmap-c)# no storm-protection

Commands

storm-action

storm-downtime

storm-rate

storm-window

613-50137-01 Rev A Command Reference for FS980M Series 898

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

STORM-RATE

storm-rate

Overview Sets the data rate that triggers the storm-action. The rate is in kbps and the range

is from 1kbps to 40Gbps.

Note that this setting is made in conjunction with the storm-window command.

Use the no variant of this command to negate the storm-rate command.

Syntax storm-rate <1-40000000>

no storm-rate

Default No default

Mode Policy Map Class Configuration

Usage This setting is made in conjunction with the storm-window command.

Examples To limit the data rate to 100Mbps, use the following commands:

awplus# configure terminal

awplus(config)# policy-map pmap2

awplus(config-pmap)# class cmap2

awplus(config-pmap-c)# storm-rate 100000

To negate the limit set previously, use the following commands:

awplus# configure terminal

awplus(config)# policy-map pmap2

awplus(config-pmap)# class cmap2

awplus(config-pmap-c)# no storm-rate

Commands

storm-action

storm-downtime

storm-protection

storm-window

Parameter Description

<1-40000000>The range of the storm-rate.

613-50137-01 Rev A Command Reference for FS980M Series 899

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

STORM-WINDOW

storm-window

Overview Sets the window size of QoS Storm Protection (QSP). This sets the time to poll the

data-rate every given milliseconds. Minimum window size is 100 ms and the

maximum size is 60 sec.

Use the no variant of this command to negate the storm-window command.

Syntax storm-window <100-60000>

no storm-window

Default No default

Mode Policy Map Class Configuration

Usage This command should be set in conjunction with the storm-rate command.

Examples To set the QSP window size to 5000 ms, use the following commands:

awplus# configure terminal

awplus(config)# policy-map pmap2

awplus(config-pmap)# class cmap2

awplus(config-pmap-c)# storm-window 5000

To negate the QSP window size set previously, use the following commands:

awplus# configure terminal

awplus(config)# policy-map pmap2

awplus(config-pmap)# class cmap2

awplus(config-pmap-c)# no storm-window

Commands

storm-action

storm-downtime

storm-protection

storm-rate

Parameter Description

<100-60000>The window size, measured in milliseconds.

613-50137-01 Rev A Command Reference for FS980M Series 900

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

TRUST DSCP

trust dscp

Overview This command enables the premark-dscp map to send traffic to a particular egress

queue, based on a lookup DSCP value.

Syntax trust dscp

no trust

Mode Policy-Map Configuration. Because policy-maps are applied to ports, you can think

of trust dscp as a per-port setting.

Examples To enable the premark-dscp map lookup for policy-map pmap1, use the

commands:

awplus# configure terminal

awplus(config)# policy-map pmap1

awplus(config-pmap)# trust dscp

To disable the premark-dscp map lookup for policy-map pmap1, use the

commands:

awplus# configure terminal

awplus(config)# policy-map pmap1

awplus(config-pmap)# no trust

Commands

mls qos map premark-dscp to

613-50137-01 Rev A Command Reference for FS980M Series 901

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

WRR-QUEUE DISABLE QUEUES

wrr-queue disable queues

Overview Use this command to disable an egress queue from transmitting traffic.

The no variant of this command enables an egress queue to transmit traffic.

Syntax wrr-queue disable queues [0][1][2][3][4][5][6][7]

no wrr-queue disable queues [0][1][2][3][4][5][6][7]

Mode Interface Configuration

Examples To disable queue 1 from transmitting traffic, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.1

awplus(config-if)# wrr-queue disable queues 1

To enable queue 1 to transmit traffic, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.1

awplus(config-if)# no wrr-queue disable queues 1

Commands

show mls qos interface

Parameter Description

[0][2]...[7] Selects one or more queues numbered 0 to 7.

613-50137-01 Rev A Command Reference for FS980M Series 902

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

WRR-QUEUE EGRESS-RATE-LIMIT QUEUES

wrr-queue egress-rate-limit queues

Overview Sets a limit on the amount of traffic that can be transmitted per second from these

queues. The default unit is in Kb, but Mb or Gb can also be specified. The minimum

is 651Kb.

Syntax wrr-queue egress-rate-limit <bandwidth> queues

[0][1][2][3][4][5][6][7]

no wrr-queue egress-rate-limit <bandwidth> queues

[0][1][2][3][4][5][6][7]

Mode Interface Configuration

Example To limit the egress rate of queues 0, 1 and 2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.1

awplus(config-if)# wrr-queue egress-rate-limit 500M queues 0 1

Commands

show mls qos interface

Parameter Description

<bandwidth>Bandwidth <1-40000000 kbits> (usable units: k, m, g).

[0][2]...[7] Selects one or more queues numbered 0 to 7.

613-50137-01 Rev A Command Reference for FS980M Series 903

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

QOS COMMANDS

WRR-QUEUE WEIGHT QUEUES

wrr-queue weight queues

Overview This command configures weighted round-robin based scheduling on the

specified egress queues on switch port interfaces only. The weights are specified

as ratios relative to each other.

Syntax wrr-queue weight <1-15> queues [0][1][2][3][4][5][6][7]

Mode Interface Configuration for switch port interfaces only (not for static aggregated

interfaces).

Usage You cannot apply weighted round-robin based scheduling to static aggregated

interfaces (for example, awplus(config)#interface sa2). Attempting to

apply weighted round-robin based scheduling on aggregated interfaces will

display the console error shown below:

awplus# configure terminal

awplus(config)# interface sa2

awplus(config-if)# wrr-queue weight

% Invalid input detected at ^ marker

Example To apply a WRR weight of 6 to queues 0 and 1 on port1.0.1, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.1

awplus(config-if)# wrr-queue weight 6 queues 0 1

Commands

priority-queue

show mls qos interface

Parameter Description

<1-15>Weight (the higher the number the greater will be the queue

servicing).

[0][2]...[7] Selects one or more queues numbered 0 to 7.

613-50137-01 Rev A Command Reference for FS980M Series 904

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X Commands

Introduction

Overview This chapter provides an alphabetical reference of commands used to configure

802.1X port access control. For more information, see the AAA and Port

Authentication Feature Overview and Configuration Guide

Command List •“debug dot1x” on page 906

•“dot1x control-direction” on page 907

•“dot1x eap” on page 909

•“dot1x eapol-version” on page 910

•“dot1x initialize interface” on page 912

•“dot1x initialize supplicant” on page 913

•“dot1x keytransmit” on page 914

•“dot1x max-auth-fail” on page 915

•“dot1x max-reauth-req” on page 917

•“dot1x port-control” on page 919

•“dot1x timeout tx-period” on page 921

•“show debugging dot1x” on page 923

•“show dot1x” on page 924

•“show dot1x diagnostics” on page 927

•“show dot1x interface” on page 929

•“show dot1x sessionstatistics” on page 934

•“show dot1x statistics interface” on page 935

•“show dot1x supplicant” on page 936

•“show dot1x supplicant interface” on page 938

613-50137-01 Rev A Command Reference for FS980M Series 905

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

•“undebug dot1x” on page 941

613-50137-01 Rev A Command Reference for FS980M Series 906

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

DEBUG DOT1X

debug dot1x

Overview Use this command to enable 802.1X IEEE Port-Based Network Access Control

troubleshooting functions.

Use the no variant of this command to disable this function.

no debug all dot1x

Mode Privileged Exec and Global Configuration

Usage This command turns on a mode where trace-level information is output during?

authentication conversations. Be aware that this is a very verbose output.? It is

mostly useful to capture this as part of escalating an issue to ATI support.

Examples Use this command without any parameters to turn on normal 802.1X debug

information.

awplus# debug dot1x

awplus# show debugging dot1x

Commands

show debugging dot1x

undebug dot1x

Parameter Description

all Used with the no variant of this command exclusively; turns off all

debugging for 802.1X.

auth-web Specifies debugging for 802.1X auth-web information.

events Specifies debugging for 802.1X events.

nsm Specifies debugging for NSM messages.

packet Specifies debugging for 802.1X packets.

timer Specifies debugging for 802.1X timers.

802.1X debugging status:

802.1X events debugging is

802.1X timer debugging is on

802.1X packets debugging is on

802.1X NSM debugging is on

613-50137-01 Rev A Command Reference for FS980M Series 907

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

DOT1X CONTROL-DIRECTION

dot1x control-direction

Overview This command sets the direction of the filter for the unauthorized interface.

If the optional in parameter is specified with this command then packets entering

the specified port are discarded. The in parameter discards the ingress packets

received from the supplicant.

If the optional both parameter is specified with this command then packets

entering (ingress) and leaving (egress) the specified port are discarded. The both

parameter discards the packets received from the supplicant and sent to the

supplicant.

The no variant of this command sets the direction of the filter to both. The port will

then discard both ingress and egress traffic.

Syntax dot1x control-direction {in|both}

no dot1x control-direction

Default The authentication port direction is set to both by default.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Examples To set the port direction to the default ( both) for port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no dot1x control-direction

To set the port direction to in for port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# dot1x control-direction in

To set the port direction to in for authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# dot1x control-direction in

Parameter Description

in Discard received packets from the supplicant (ingress

packets).

both Discard received packets from the supplicant (ingress

packets) and transmitted packets to the supplicant (egress

packets).

613-50137-01 Rev A Command Reference for FS980M Series 908

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

DOT1X CONTROL-DIRECTION

To set the port direction to the default (both) for authentication profile ‘student’,

use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no dot1x control-direction

Commands

auth profile (Global Configuration)

show dot1x

show dot1x interface

show auth interface

613-50137-01 Rev A Command Reference for FS980M Series 909

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

DOT1X EAP

dot1x eap

Overview This command selects the transmit mode for the EAP packet. If the authentication

feature is not enabled then EAP transmit mode is not enabled. The default setting

discards EAP packets.

Syntax dot1x eap {discard|forward|forward-untagged-vlan|forward-vlan}

Default The transmit mode is set to discard EAP packets by default.

Mode Global Configuration

Examples To set the transmit mode of EAP packet to forward to forward EAP packets to all

ports on the switch, use the commands:

awplus# configure terminal

awplus(config)# dot1x eap forward

To set the transmit mode of EAP packet to discard to discard EAP packets, use

the commands:

awplus# configure terminal

awplus(config)# dot1x eap discard

To set the transmit mode of EAP packet to forward-untagged-vlan to

forward EAP packets to ports with the same untagged vlan, use the commands:

awplus# configure terminal

awplus(config)# dot1x eap forward-untagged-vlan

To set the transmit mode of EAP packet to forward-vlan to forward EAP

packets to ports with the same vlan, use the commands:

awplus# configure terminal

awplus(config)# dot1x eap forward-vlan

Parameter Description

discard Discard.

forward Forward to all ports on the switch.

forward-untagged-vlan Forward to ports with the same untagged VLAN.

forward-vlan Forward to ports with the same VLAN.

613-50137-01 Rev A Command Reference for FS980M Series 910

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

DOT1X EAPOL-VERSION

dot1x eapol-version

Overview This command sets the EAPOL protocol version for EAP packets when 802.1X port

authentication is applied.

Use the no variant of this command to set the EAPOL protocol version to 1.

The default EAPOL protocol version is version 1.

Syntax dot1x eapol-version {1|2}

no dot1x eapol-version

Default The EAP version for 802.1X authentication is set to 1 by default.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Examples To set the EAPOL protocol version to 2 for port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# dot1x eapol-version 2

To set the EAPOL protocol version to the default version (1) for interface

port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no dot1x eapol-version

To set the EAPOL protocol version to 2 for authentication profile 'student', use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# dot1x eapol-version 2

To set the EAPOL protocol version to the default version (1) for authentication

profile 'student', use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no dot1x eapol-version

Parameter Description

1EAPOL version.

2EAPOL version.

613-50137-01 Rev A Command Reference for FS980M Series 911

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

DOT1X EAPOL-VERSION

Validation

Commands

auth profile (Global Configuration)

show dot1x

show dot1x interface

613-50137-01 Rev A Command Reference for FS980M Series 912

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

DOT1X INITIALIZE INTERFACE

dot1x initialize interface

Overview This command removes authorization for a connected interface with the

specified<interface-list>. The connection will attempt to re-authorize when the

specified port attempts to make use of the network connection.

NOTE: Reauthentication could be a long time after the use of this command because

the reauthorization attempt is not triggered by this command. The attempt is triggered

by the first packet from the interface trying to access the network resources.

Syntax dot1x initialize interface <interface-list>

Mode Privileged Exec

Examples To initialize 802.1X port authentication on the interface port1.0.2, use the

command:

awplus# dot1x initialize interface port1.0.2

To unauthorize switch port1.0.1 and attempt reauthentication on switch

port1.0.1, use the command:

awplus# dot1x initialize interface port1.0.1

Validation

Commands

show dot1x

show dot1x interface

Commands

dot1x initialize supplicant

Parameter Description

<interface-list> The interfaces or ports to configure. An interface-list can be:

• an interface (e.g. vlan2), a switch port (e.g. port1.0.6),

a static channel group (e.g. sa2) or a dynamic (LACP)

channel group (e.g. po2)

• a continuous range of interfaces, ports, static channel

groups or dynamic (LACP) channel groups separated by a

hyphen; e.g. vlan2-8, or port1.0.1-1.0.6, or sa1-2,

or po1-2

• a comma-separated list of the above; e.g.

port1.0.1,port1.0.2-1.0.4. Do not mix interface

types in a list

The specified interfaces must exist.

613-50137-01 Rev A Command Reference for FS980M Series 913

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

DOT1X INITIALIZE SUPPLICANT

dot1x initialize supplicant

Overview This command removes authorization for a connected supplicant with the

specified MAC address or username. The connection will attempt to re-authorize

when the specified supplicant attempts to make use of the network connection.

NOTE: Reauthentication could be a long time after the use of this command because

the reauthorization attempt is not triggered by this command. The attempt is triggered

by the first packet from the supplicant trying to access the network resources.

Syntax dot1x initialize supplicant {<macadd>|username}

Mode Privileged Exec

Example To initialize the supplicant authentication, use the commands

awplus# configure terminal

awplus(config)# dot1x initialize supplicant 0090.99ab.a020

awplus(config)# dot1x initialize supplicant guest

Validation

Commands

show dot1x

show dot1x supplicant

Commands

dot1x initialize interface

Parameter Description

dot1x IEEE 802.1X Port-Based Access Control.

initialize Initialize the port to attempt reauthentication.

supplicant Specify the supplicant to initialize.

<macadd>MAC (hardware address of the supplicant.

username The name of the supplicant entry.

613-50137-01 Rev A Command Reference for FS980M Series 914

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

DOT1X KEYTRANSMIT

dot1x keytransmit

Overview This command enables key transmission on the interface specified previously in

Interface mode.

The no variant of this command disables key transmission on the interface

specified.

Syntax dot1x keytransmit

no dot1x keytransmit

Default Key transmission for port authentication is enabled by default.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port.

Usage Use this command to enable key transmission over an Extensible Authentication

Protocol (EAP) packet between the authenticator and supplicant. Use the no

variant of this command to disable key transmission.

Examples To enable the key transmit feature on interface port1.0.2, after it has been

disabled by negation, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# dot1x keytransmit

To disable the key transmit feature from the default startup configuration on

interface port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no dot1x keytransmit

Validation

Commands

show dot1x

show dot1x interface

613-50137-01 Rev A Command Reference for FS980M Series 915

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

DOT1X MAX-AUTH-FAIL

dot1x max-auth-fail

Overview Use this command to configure the maximum number of login attempts for a

supplicant (client device) using the auth-fail vlan feature, when using 802.1X port

authentication on an interface.

The no variant of this command resets the maximum login attempts for a

supplicant (client device) using the auth-fail vlan feature, to the default

configuration of 3 login attempts.

Syntax dot1x max-auth-fail <0-10>

no dot1x max-auth-fail

Default The default maximum number of login attempts for a supplicant on an interface

using 802.1X port authentication is three (3) login attempts.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Usage This command sets the maximum number of login attempts for supplicants on an

interface. The supplicant is moved to the auth-fail VLAN from the Guest VLAN after

the number of failed login attempts using 802.1X authentication is equal to the

number set with this command.

See the AAA and Port Authentication Feature Overview and Configuration Guide

for information about:

• the auth-fail VLAN feature, and

• restrictions regarding combinations of authentication enhancements

working together

Examples To configure the maximum number of login attempts for a supplicant on interface

port1.0.2 to a single (1) login attempt, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# dot1x max-auth-fail 1

To configure the maximum number of login attempts for a supplicant on interface

port1.0.2 to the default number of three (3) login attempts, use the

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no dot1x max-auth-fail

Parameter Description

<0-10>Specify the maximum number of login attempts for supplicants

on an interface using 802.1X port authentication.

613-50137-01 Rev A Command Reference for FS980M Series 916

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

DOT1X MAX-AUTH-FAIL

To configure the maximum number of login attempts for a supplicant on

authentication profile 'student' to a single (1) login attempt, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# dot1x max-auth-fail 1

To configure the maximum number of login attempts for a supplicant on

authentication profile 'student' to the default number of three (3) login attempts,

use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no dot1x max-auth-fail

Validation

Commands

show running-config

show dot1x interface

Commands

auth auth-fail vlan

auth profile (Global Configuration)

dot1x max-reauth-req

613-50137-01 Rev A Command Reference for FS980M Series 917

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

DOT1X MAX-REAUTH-REQ

dot1x max-reauth-req

Overview This command sets the number of reauthentication attempts before an interface

is unauthorized.

The no variant of this command resets the reauthentication delay to the default.

Syntax dot1x max-reauth-req <1-10>

no dot1x max-reauth-req

Default The default maximum reauthentication attempts for interfaces using 802.1X port

authentication is two (2) reauthentication attempts, before an interface is

unauthorized.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Usage Use this command to set the maximum reauthentication attempts after failure.

Examples To configure the maximum number of reauthentication attempts for interface

port1.0.2 to a single (1) reauthentication request, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# dot1x max-reauth-req 1

To configure the maximum number of reauthentication attempts for interface

port1.0.2 to the default maximum number of two (2) reauthentication

attempts, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no dot1x max-reauth-req

To configure the maximum number of reauthentication attempts for

authentication profile 'student' to a single (1) reauthentication request, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# dot1x max-reauth-req 1

Parameter Description

<1-10>Specify the maximum number of reauthentication attempts for

supplicants on an interface using 802.1X port authentication.

613-50137-01 Rev A Command Reference for FS980M Series 918

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

DOT1X MAX-REAUTH-REQ

To configure the maximum number of reauthentication attempts for

authentication profile 'student' to the default maximum number of two (2)

reauthentication attempts, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no dot1x max-reauth-req

Validation

Commands

show running-config

Commands

auth profile (Global Configuration)

dot1x max-auth-fail

show dot1x interface

613-50137-01 Rev A Command Reference for FS980M Series 919

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

DOT1X PORT-CONTROL

dot1x port-control

Overview This command enables 802.1X port authentication on the interface specified, and

sets the control of the authentication port.

The no variant of this command disables the port authentication on the interface

specified.

Syntax dot1x port-control {force-unauthorized|force-authorized|auto}

no dot1x port-control

Default 802.1X port control is disabled by default.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Usage Use this command to force a port state.

When port-control is set to auto, the 802.1X authentication feature is executed on

the interface, but only if the aaa authentication dot1x command has been issued.

Examples To enable port authentication on the interface port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# dot1x port-control auto

To enable port authentication force authorized on the interface port1.0.2, use

the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# dot1x port-control force-authorized

Parameter Description

force-unauthorized Force the port state to unauthorized.

Specify this to force a port to always be in an unauthorized

state.

force-authorized Force the port state to authorized.

Specify this to force a port to always be in an authorized

state.

auto Allow the port client to negotiate authentication.

Specify this to enable authentication on the port.

613-50137-01 Rev A Command Reference for FS980M Series 920

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

DOT1X PORT-CONTROL

To disable port authentication on the interface port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no dot1x port-control

To enable port authentication on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# dot1x port-control auto

To enable port authentication force authorized on authentication profile ‘student’,

use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# dot1x port-control

force-authorized

To disable port authentication on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no dot1x port-control

Validation

Commands

show dot1x interface

Commands

aaa authentication dot1x

auth profile (Global Configuration)

613-50137-01 Rev A Command Reference for FS980M Series 921

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

DOT1X TIMEOUT TX-PERIOD

dot1x timeout tx-period

Overview This command sets the transmit timeout for the authentication request on the

specified interface.

The no variant of this command resets the transmit timeout period to the default

(30 seconds).

Syntax dot1x timeout tx-period <1-65535>

no dot1x timeout tx-period

Default The default transmit period for port authentication is 30 seconds.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Usage Use this command to set the interval between successive attempts to request an

ID.

Examples To set the transmit timeout period to 5 seconds on interface port1.0.2, use the

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# dot1x timeout tx-period 5

To reset transmit timeout period to the default (30 seconds) on interface

port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no dot1x timeout tx-period

To set the transmit timeout period to 5 seconds on authentication profile ‘student’,

use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# dot1x timeout tx-period 5

To reset transmit timeout period to the default (30 seconds) on authentication

profile ‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no dot1x timeout tx-period

Parameter Description

<1-65535>Seconds.

613-50137-01 Rev A Command Reference for FS980M Series 922

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

DOT1X TIMEOUT TX-PERIOD

Validation

Commands

auth profile (Global Configuration)

show dot1x

show dot1x interface

613-50137-01 Rev A Command Reference for FS980M Series 923

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DEBUGGING DOT1X

show debugging dot1x

Overview Use this command to display the 802.1X debugging option set.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show debugging dot1x

Mode User Exec and Privileged Exec

Usage This is a sample output from the show debugging dot1x command.

awplus# debug dot1x

awplus# show debugging dot1x

Commands

debug dot1x

802.1X debugging status:

802.1X events debugging is on

802.1X timer debugging is on

802.1X packets debugging is on

802.1X NSM debugging is on

613-50137-01 Rev A Command Reference for FS980M Series 924

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DOT1X

show dot1x

Overview This command shows authentication information for dot1x (802.1X) port

authentication.

If you specify the optional all parameter then this command also displays all

authentication information for each port available on the switch.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show dot1x [all]

Mode Privileged Exec

Example awplus# show dot1x all

Parameter Description

all Displays all authentication information for each port available on the

switch.

Table 1: Example output from the show dot1x command

awplus# show dot1x all

802.1X Port-Based Authentication Enabled

RADIUS server address: 150.87.18.89:1812

Next radius message id: 5

RADIUS client address: not configured

Authentication info for interface port1.0.6

portEnabled: true - portControl: Auto

portStatus: Authorized

reAuthenticate: disabled

reAuthPeriod: 3600

PAE: quietPeriod: 60 - maxReauthReq: 2 - txPeriod: 30

PAE: connectTimeout: 30

BE: suppTimeout: 30 - serverTimeout: 30

CD: adminControlledDirections: in

KT: keyTxEnabled: false

critical: disabled

guestVlan: disabled

dynamicVlanCreation: single-dynamic-vlan

assignFailActionRule: deny

hostMode: multi-supplicant

maxSupplicant:

256

613-50137-01 Rev A Command Reference for FS980M Series 925

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DOT1X

dot1x: enabled

protocolVersion: 1

authMac: enabled

method: PAP

reauthRelearning: disabled

authWeb: enabled

method: PAP

lockCount: 3

packetForwarding: disabled

twoStepAuthentication:

configured: enabled

actual: enabled

SupplicantMac: none

supplicantMac: none

Supplicant name: manager

Supplicant address: 00d0.59ab.7037

authenticationMethod: 802.1X Authentication

portStatus: Authorized - currentId: 1

abort:F fail:F start:F timeout:F success:T

PAE: state: Authenticated - portMode: Auto

PAE: reAuthCount: 0 - rxRespId: 0

PAE: quietPeriod: 60 - maxReauthReq: 2 - txPeriod: 30

BE: state: Idle - reqCount: 0 - idFromServer: 0

CD: adminControlledDirections: in - operControlledDirections: in

CD: bridgeDetected: false

KR: rxKey: false

KT: keyAvailable: false - keyTxEnabled: false

criticalState: off

dynamicVlanId: 2

802.1X statistics for interface port1.0.6

EAPOL Frames Rx: 5 - EAPOL Frames Tx: 16

EAPOL Start Frames Rx: 0 - EAPOL Logoff Frames Rx: 0

EAP Rsp/Id Frames Rx: 3 - EAP Response Frames Rx: 2

EAP Req/Id Frames Tx: 8 - EAP Request Frames Tx: 2

Invalid EAPOL Frames Rx: 0 - EAP Length Error Frames Rx: 0

EAPOL Last Frame Version Rx: 1 - EAPOL Last Frame Src: 00d0.59ab.7037

Authentication session statistics for interface port1.0.6

session user name: manager

session authentication method: Remote server

session time: 19440 secs

session terminate cause: Not terminated yet

Authentication Diagnostics for interface port1.0.6

Supplicant address: 00d0.59ab.7037

authEnterConnecting: 2

authEaplogoffWhileConnecting: 1

authEnterAuthenticating: 2

authSuccessWhileAuthenticating: 1

authTimeoutWhileAuthenticating: 1

authFailWhileAuthenticating: 0

authEapstartWhileAuthenticating: 0

Table 1: Example output from the show dot1x command (cont.)

613-50137-01 Rev A Command Reference for FS980M Series 926

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DOT1X

authEaplogoggWhileAuthenticating: 0

authReauthsWhileAuthenticated: 0

authEapstartWhileAuthenticated: 0

authEaplogoffWhileAuthenticated: 0

BackendResponses: 2

BackendAccessChallenges: 1

BackendOtherrequestToSupplicant: 3

BackendAuthSuccess: 1

BackendAuthFails: 0

Table 1: Example output from the show dot1x command (cont.)

613-50137-01 Rev A Command Reference for FS980M Series 927

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DOT1X DIAGNOSTICS

show dot1x diagnostics

Overview This command shows 802.1X authentication diagnostics for the specified interface

(optional), which may be a static channel (or static aggregator) or a dynamic (or

LACP) channel group or a switch port.

If no interface is specified then authentication diagnostics are shown for all

interfaces.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show dot1x diagnostics [interface <interface-list>]

Mode Privileged Exec

Example See the sample output below showing 802.1X authentication diagnostics for

port1.0.5:

awplus# show dot1x diagnostics interface port1.0.5

Parameter Description

interface Specify a port to show.

<interface-list> The interfaces or ports to configure. An interface-list can be:

• an interface (e.g. vlan2), a switch port (e.g. port1.0.6),

a static channel group (e.g. sa2) or a dynamic (LACP)

channel group (e.g. po2)

• a continuous range of interfaces, ports, static channel

groups or dynamic (LACP) channel groups separated by a

hyphen; e.g. vlan2-8, or port1.0.1-1.0.4, or

sa1-2, or po1-2

• a comma-separated list of the above; e.g.

port1.0.1,port1.0.2-1.0.4. Do not mix interface

types in a list

The specified interfaces must exist.

613-50137-01 Rev A Command Reference for FS980M Series 928

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DOT1X DIAGNOSTICS

Output Figure 28-1: Example output from the show dot1x diagnostics command

Authentication Diagnostics for interface port1.0.5

Supplicant address: 00d0.59ab.7037

authEnterConnecting: 2

authEaplogoffWhileConnecting: 1

authEnterAuthenticating: 2

authSuccessWhileAuthenticating: 1

authTimeoutWhileAuthenticating: 1

authFailWhileAuthenticating: 0

authEapstartWhileAuthenticating: 0

authEaplogoggWhileAuthenticating: 0

authReauthsWhileAuthenticated: 0

authEapstartWhileAuthenticated: 0

authEaplogoffWhileAuthenticated: 0

BackendResponses: 2

BackendAccessChallenges: 1

BackendOtherrequestToSupplicant: 3

BackendAuthSuccess: 1

613-50137-01 Rev A Command Reference for FS980M Series 929

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DOT1X INTERFACE

show dot1x interface

Overview This command shows the status of 802.1X port-based authentication on the

specified interface, which may be a static channel (or static aggregator) or a

dynamic (or LACP) channel group or a switch port.

Use the optional diagnostics parameter to show authentication diagnostics for

the specified interfaces. Use the optional sessionstatistics parameter to show

authentication session statistics for the specified interfaces. Use the optional

statistics parameter to show authentication diagnostics for the specified

interfaces. Use the optional supplicant parameter to show the supplicant state for

the specified interfaces.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show dot1x interface <interface-list>

[diagnostics|sessionstatistics|statistics|supplicant [brief]]

Mode Privileged Exec

Examples See the sample output below showing 802.1X authentication status for

port1.0.6:

awplus# show dot1x interface port1.0.6

Parameter Description

<interface-list> The interfaces or ports to configure. An interface-list can be:

• an interface (e.g. vlan2), a switch port (e.g.

port1.0.6), a static channel group (e.g. sa2) or a

dynamic (LACP) channel group (e.g. po2)

• a continuous range of interfaces, ports, static channel

groups or dynamic (LACP) channel groups separated by a

hyphen; e.g. vlan2-8, or port1.0.1-1.0.4, or

sa1-2, or po1-2

• a comma-separated list of the above; e.g.

port1.0.1,port1.0.3-1.0.5. Do not mix

interface types in a list

The specified interfaces must exist.

diagnostics Diagnostics.

sessionstatistics Session Statistics.

statistics Statistics.

supplicant Supplicant.

brief Brief summary of supplicant state.

613-50137-01 Rev A Command Reference for FS980M Series 930

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DOT1X INTERFACE

See the sample output below showing 802.1X authentication

sessionstatistics for port1.0.6:

awplus# show dot1x interface port1.0.6 sessionstatistics

See sample output below showing 802.1X authentication diagnostics for

port1.0.6:

awplus# show dot1x interface port1.0.6 diagnostics

Table 2: Example output from the show dot1x interface command for a port

awplus#show dot1x interface port1.0.6Authentication info for

interface port1.0.6

portEnabled: true - portControl: Auto

portStatus: Authorized

reAuthenticate: disabled

reAuthPeriod: 3600

PAE: quietPeriod: 60 - maxReauthReq: 2 - txPeriod: 30

PAE: connectTimeout: 30 

BE: suppTimeout: 30 - serverTimeout: 30

CD: adminControlledDirections: in

KT: keyTxEnabled: false

critical: disabled

guestVlan: disabled

dynamicVlanCreation: single-dynamic-vlan

assignFailActionRule: deny

hostMode: multi-supplicant

maxSupplicant: 256

dot1x: enabled

protocolVersion: 1

authMac: enabled

method: PAP

reauthRelearning: disabled

authWeb: enabled

method: PAP

lockCount: 3

packetForwarding: disabled

twoStepAuthentication:

configured: enabled

actual: enabled

supplicantMac: none

awplus#show dot1x interface port1.0.6 

sessionstatistics

Authentication session statistics for interface 

port1.0.6

session user name: manager

session authentication method: Remote server

session time: 19440 secs

session terminat cause: Not terminated yet

613-50137-01 Rev A Command Reference for FS980M Series 931

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DOT1X INTERFACE

See sample output below showing the supplicant on the interface

port1.0.6:

awplus# show dot1x interface port1.0.6 supplicant

See sample output below showing 802.1X (dot1x) authentication statistics for

port1.0.6:

awplus# show dot1x statistics interface port1.0.6

awplus#show dot1x interface port1.0.6 diagnostics

Authentication Diagnostics for interface port1.0.6

Supplicant address: 00d0.59ab.7037

authEnterConnecting: 2

authEaplogoffWhileConnecting: 1

authEnterAuthenticating: 2

authSuccessWhileAuthenticating: 1

authTimeoutWhileAuthenticating: 1

authFailWhileAuthenticating: 0

authEapstartWhileAuthenticating: 0

authEaplogoggWhileAuthenticating: 0

authReauthsWhileAuthenticated: 0

authEapstartWhileAuthenticated: 0

authEaplogoffWhileAuthenticated: 0

BackendResponses: 2

BackendAccessChallenges: 1

BackendOtherrequestToSupplicant: 3

BackendAuthSuccess: 1

awplus#show dot1x interface port1.0.6 supplicant

authenticationMethod: dot1x

totalSupplicantNum: 1

authorizedSupplicantNum: 1

macBasedAuthenticationSupplicantNum: 0

dot1xAuthenticationSupplicantNum: 1

webBasedAuthenticationSupplicantNum: 0

Supplicant name: manager

Supplicant address: 00d0.59ab.7037

authenticationMethod: dot1x

portStatus: Authorized - currentId: 4

abort:F fail:F start:F timeout:F success:T

PAE: state: Authenticated - portMode: Auto

PAE: reAuthCount: 0 - rxRespId: 0

PAE: quietPeriod: 60 - maxReauthReq: 2 - txPeriod: 30

BE: state: Idle - reqCount: 0 - idFromServer: 3

BE: suppTimeout: 30 - serverTimeout: 30

CD: adminControlledDirections: in -

operControlledDirections: in

CD: bridgeDetected: false

KR: rxKey: false

KT: keyAvailable: false - keyTxEnabled: false

613-50137-01 Rev A Command Reference for FS980M Series 932

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DOT1X INTERFACE

awplus#show dot1x statistics interface port1.0.6802.1X statistics

for interface port1.0.6

EAPOL Frames Rx: 5 - EAPOL Frames Tx: 16

EAPOL Start Frames Rx: 0 - EAPOL Logoff Frames Rx: 0

EAP Rsp/Id Frames Rx: 3 - EAP Response Frames Rx: 2

EAP Req/Id Frames Tx: 8 - EAP Request Frames Tx: 2

Invalid EAPOL Frames Rx: 0 - EAP Length Error Frames Rx: 0

EAPOL Last Frame Version Rx: 1 - EAPOL Last Frame 

Src:00d0.59ab.7037

Table 28-1: Parameters in the output of show dot1x interface

Parameter Description

portEnabled Interface operational status (Up-true/down-false).

portControl Current control status of the port for 802.1X control.

portStatus 802.1X status of the port (authorized/unauthorized).

reAuthenticate Reauthentication enabled/disabled status on port.

reAuthPeriod Value holds meaning only if reauthentication is enabled.

abort Indicates that authentication should be aborted when set

to true.

fail Indicates failed authentication attempt when set to false.

start Indicates authentication should be started when set to

true.

timeout Indicates authentication attempt timed out when set to

true.

success Indicates authentication successful when set to true.

state Current 802.1X operational state of interface.

mode Configured 802.1X mode.

reAuthCount Reauthentication count.

quietperiod Time between reauthentication attempts.

reAuthMax Maximum reauthentication attempts.

BE Backend authentication state machine variables and

constants.

state State of the state machine.

reqCount Count of requests sent to server.

613-50137-01 Rev A Command Reference for FS980M Series 933

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DOT1X INTERFACE

Commands

show auth diagnostics

show dot1x sessionstatistics

show dot1x statistics interface

show dot1x supplicant interface

suppTimeout Supplicant timeout.

serverTimeout Server timeout.

maxReq Maximum requests to be sent.

CD Controlled Directions State machine.

adminControlledDi

r ections

Administrative value (Both/In).

operControlledDir

e ctions

Operational Value (Both/In).

KR Key receive state machine.

rxKey True when EAPOL-Key message is received by supplicant

or authenticator. false when key is transmitted.

KT Ket Transmit State machine.

keyAvailable False when key has been transmitted by authenticator,

true when new key is available for key exchange.

keyTxEnabled Key transmission enabled/disabled status.

Table 28-1: Parameters in the output of show dot1x interface (cont.)

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 934

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DOT1X SESSIONSTATISTICS

show dot1x sessionstatistics

Overview This command shows authentication session statistics for the specified interface,

which may be a static channel (or static aggregator) or a dynamic (or LACP)

channel group or a switch port.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show dot1x sessionstatistics [interface <interface-list>]

Mode Privileged Exec

Example See sample output below showing 802.1X (dot1x) authentication session

statistics for port1.0.6:

awplus# show dot1x sessionstatistics interface port1.0.6

Parameter Description

interface Specify a port to show.

<interface-list> The interfaces or ports to configure. An interface-list can be:

•an interface (e.g. vlan2), a switch port (e.g. port1.0.6),

a static channel group (e.g. sa2) or a dynamic (LACP)

channel group (e.g. po2)

• a continuous range of interfaces, ports, static channel

groups or dynamic (LACP) channel groups separated by a

hyphen; e.g. vlan2-8, or port1.0.1-1.0.4, or

sa1-2, or po1-2

• a comma-separated list of the above; e.g.

port1.0.1,port1.0.4-1.0.6. Do not mix interface

types in a list

The specified interfaces must exist.

Authentication session statistics for interface 

port1.0.6

session user name: manager

session authentication method: Remote server

session time: 19440 secs

session terminat cause: Not terminated yet

613-50137-01 Rev A Command Reference for FS980M Series 935

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DOT1X STATISTICS INTERFACE

show dot1x statistics interface

Overview This command shows the authentication statistics for the specified interface,

which may be a static channel (or static aggregator) or a dynamic (or LACP)

channel group or a switch port.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show dot1x statistics interface <interface-list>

Mode Privileged Exec

Example See sample output below showing 802.1X authentication statistics for

port1.0.6:

awplus# show dot1x statistics interface port1.0.6

Parameter Description

<interface-list> The interfaces or ports to configure. An interface-list can be:

•an interface (e.g. vlan2), a switch port (e.g. port1.0.6),

a static channel group (e.g. sa2) or a dynamic (LACP)

channel group (e.g. po2)

• a continuous range of interfaces, ports, static channel

groups or dynamic (LACP) channel groups separated by a

hyphen; e.g. vlan2-8, or port1.0.1-1.0.4, or sa1-2,

or po1-2

• a comma-separated list of the above; e.g.

port1.0.1,port1.0.4-1.0.6. Do not mix interface

types in a list

The specified interfaces must exist.

802.1X statistics for interface port1.0.6

EAPOL Frames Rx: 5 - EAPOL Frames Tx: 16

EAPOL Start Frames Rx: 0 - EAPOL Logoff Frames Rx: 0

EAP Rsp/Id Frames Rx: 3 - EAP Response Frames Rx: 2

EAP Req/Id Frames Tx: 8 - EAP Request Frames Tx: 2

Invalid EAPOL Frames Rx: 0 - EAP Length Error Frames Rx: 0

EAPOL Last Frame Version Rx: 1 - EAPOL Last Frame 

Src:00d0.59ab.7037

613-50137-01 Rev A Command Reference for FS980M Series 936

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DOT1X SUPPLICANT

show dot1x supplicant

Overview This command shows the supplicant state of the authentication mode set for the

switch.

This command shows a summary when the optional brief parameter is used.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show dot1x supplicant [<macadd>] [brief]

Mode Privileged Exec

Example See sample output below showing the 802.1X authenticated supplicant on the

switch:

awplus# show dot1x supplicant

See sample output below showing the supplicant on the switch using the brief

parameter:

awplus# show dot1x supplicant 00d0.59ab.7037 brief

Parameter Description

<macadd>MAC (hardware) address of the Supplicant.

brief Brief summary of the Supplicant state.

authenticationMethod: dot1x

totalSupplicantNum: 1

authorizedSupplicantNum: 1

macBasedAuthenticationSupplicantNum: 0

dot1xAuthenticationSupplicantNum: 1

webBasedAuthenticationSupplicantNum: 0

Supplicant name: manager

Supplicant address: 00d0.59ab.7037

authenticationMethod: dot1x

Two-Step Authentication:

firstAuthentication: Pass - Method: mac

secondAuthentication: Pass - Method: dot1x

portStatus: Authorized - currentId: 4

abort:F fail:F start:F timeout:F success:T

PAE: state: Authenticated - portMode: Auto

PAE: reAuthCount: 0 - rxRespId: 0

PAE: quietPeriod: 60 - maxReauthReq: 2 - txPeriod: 30

BE: state: Idle - reqCount: 0 - idFromServer: 3

BE: suppTimeout: 30 - serverTimeout: 30

CD: adminControlledDirections: in - operControlledDirections: in

CD: bridgeDetected: false

KR: rxKey: false

KT: keyAvailable: false - keyTxEnabled: false

613-50137-01 Rev A Command Reference for FS980M Series 937

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DOT1X SUPPLICANT

See sample output below showing the supplicant on the switch using the brief

parameter:

awplus# show dot1x supplicant brief

For example, if two-step authentication is configured with 802.1X authentication

as the first method and web authentication as the second method then the output

is as follows:

Commands

show dot1x supplicant interface

Interface port1.0.6

authenticationMethod: dot1x

totalSupplicantNum: 1

authorizedSupplicantNum: 1

macBasedAuthenticationSupplicantNum: 0

dot1xAuthenticationSupplicantNum: 1

webBasedAuthenticationSupplicantNum: 0

Interface VID Mode MAC Address Status IP Address Username

========= === ==== =========== ====== ========== ========

port1.0.6

2 D 00d0.59ab.7037 Authenticated 192.168.2.201 manager

Interface port1.0.6 authenticationMethod: dot1x/web

Two-Step Authentication

firstMethod: dot1x

secondMethod: web

totalSupplicantNum: 1

authorizedSupplicantNum: 1

macBasedAuthenticationSupplicantNum: 0

dot1xAuthenticationSupplicantNum: 0

webBasedAuthenticationSupplicantNum: 1

otherAuthenticationSupplicantNum: 0



Interface VID Mode MAC Address Status IP Address Username

=========== ==== ==== ============== ================= =============== ========

port1.0.6

5 W 0008.0d5e.c216 Authenticated 192.168.1.200 web

613-50137-01 Rev A Command Reference for FS980M Series 938

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DOT1X SUPPLICANT INTERFACE

show dot1x supplicant interface

Overview This command shows the supplicant state of the authentication mode set for the

interface, which may be a static channel (or static aggregator) or a dynamic (or

LACP) channel group or a switch port.

This command shows a summary when the optional brief parameter is used.

For information on filtering and saving command output, see the “Getting Started

with AlliedWare Plus” Feature Overview and Configuration Guide.

Syntax show dot1x supplicant interface <interface-list> [brief]

Mode Privileged Exec

Examples See sample output below showing the supplicant on the interface port1.0.6:

awplus# show dot1x interface port1.0.6

Parameter Description

<interface-list> The interfaces or ports to configure. An interface-list can be:

•an interface (e.g. vlan2), a switch port (e.g. port1.0.6),

a static channel group (e.g. sa2) or a dynamic (LACP)

channel group (e.g. po2)

• a continuous range of interfaces, ports, static channel

groups or dynamic (LACP) channel groups separated by a

hyphen; e.g. vlan2-8, or port1.0.1-1.0.4, or

sa1-2, or po1-2

• a comma-separated list of the above; e.g.

port1.0.1,port1.0.4-1.0.6. Do not mix interface

types in a list

The specified interfaces must exist.

brief Brief summary of the Supplicant state.

613-50137-01 Rev A Command Reference for FS980M Series 939

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DOT1X SUPPLICANT INTERFACE

See sample output below showing the supplicant on the switch using the brief

parameter:

awplus# show dot1x supplicant interface brief

See the sample output below for static channel group (static aggregator) interface

sa1:

awplus# show dot1x interface sa1 supplicant brief

Interface port1.0.6 authenticationMethod: dot1x

totalSupplicantNum: 1

authorizedSupplicantNum: 1

macBasedAuthenticationSupplicantNum: 0

dot1xAuthenticationSupplicantNum: 1

webBasedAuthenticationSupplicantNum: 0

otherAuthenticationSupplicantNum: 0



Supplicant name: VCSPCVLAN10

Supplicant address: 0000.cd07.7b60

authenticationMethod: 802.1X

Two-Step Authentication:

firstAuthentication: Pass - Method: mac

secondAuthentication: Pass - Method: dot1x

portStatus: Authorized - currentId: 3

abort:F fail:F start:F timeout:F success:T

PAE: state: Authenticated - portMode: Auto

PAE: reAuthCount: 0 - rxRespId: 0

PAE: quietPeriod: 60 - maxReauthReq: 2

BE: state: Idle - reqCount: 0 - idFromServer: 2

CD: adminControlledDirections:in - 

operControlledDirections:in

CD: bridgeDetected: false

KR: rxKey: false

KT: keyAvailable: false - keyTxEnabled: false

Interface port1.0.6

authenticationMethod: dot1x

Two-Step Authentication:

firstMethod: mac

secondMethod: dot1x

totalSupplicantNum: 1

authorizedSupplicantNum: 1

macBasedAuthenticationSupplicantNum: 0

dot1xAuthenticationSupplicantNum: 1

webBasedAuthenticationSupplicantNum: 0



Interface VID Mode MAC Address Status IP Address Username

========= === ==== =========== ====== ========== ========

port1.0.6

2 D 00d0.59ab.7037 Authenticated 192.168.2.201 manager

613-50137-01 Rev A Command Reference for FS980M Series 940

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

SHOW DOT1X SUPPLICANT INTERFACE

Commands

show dot1x supplicant

awplus#show dot1x interface sa1 supplicant brief

Interface sa1

authenticationMethod: dot1x

Two-Step Authentication:

firstMethod: mac

secondMethod: dot1x

totalSupplicantNum: 1

authorizedSupplicantNum: 1

macBasedAuthenticationSupplicantNum: 0

dot1xAuthenticationSupplicantNum: 1

webBasedAuthenticationSupplicantNum: 0

otherAuthenticationSupplicantNum: 0



Interface VID Mode MAC Address Status IP Address Username

========= ==== ==== ============== ================= =============== ========

sa1 1 D 00d0.59ab.7037 Authenticated -- test1

613-50137-01 Rev A Command Reference for FS980M Series 941

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

802.1X COMMANDS

UNDEBUG DOT1X

undebug dot1x

Overview This command applies the functionality of the no variant of the debug dot1x

command.

613-50137-01 Rev A Command Reference for FS980M Series 942

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Authentication

Commands

Introduction

Overview This chapter provides an alphabetical reference for authentication commands. For

more information, see the AAA and Port Authentication Feature Overview and

Configuration Guide.

Command List •“auth auth-fail vlan” on page 945

•“auth critical” on page 947

•“auth dynamic-vlan-creation” on page 948

•“auth guest-vlan” on page 951

•“auth guest-vlan forward” on page 954

•“auth host-mode” on page 956

•“auth log” on page 958

•“auth max-supplicant” on page 960

•“auth profile (Global Configuration)” on page 962

•“auth profile (Interface Configuration)” on page 963

•“auth reauthentication” on page 964

•“auth roaming disconnected” on page 965

•“auth roaming enable” on page 967

•“auth supplicant-ip” on page 969

•“auth supplicant-mac” on page 971

•“auth timeout connect-timeout” on page 974

•“auth timeout quiet-period” on page 976

•“auth timeout reauth-period” on page 977

•“auth timeout server-timeout” on page 979

613-50137-01 Rev A Command Reference for FS980M Series 943

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

•“auth timeout supp-timeout” on page 981

•“auth two-step enable” on page 983

•“auth-mac enable” on page 986

•“auth-mac method” on page 988

•“auth-mac password” on page 990

•“auth-mac reauth-relearning” on page 991

•“auth-mac username” on page 992

•“auth-web enable” on page 993

•“auth-web forward” on page 995

•“auth-web max-auth-fail” on page 998

•“auth-web method” on page 1000

•“auth-web-server blocking-mode” on page 1001

•“auth-web-server dhcp ipaddress” on page 1002

•“auth-web-server dhcp lease” on page 1003

•“auth-web-server dhcp-wpad-option” on page 1004

•“auth-web-server host-name” on page 1005

•“auth-web-server intercept-port” on page 1006

•“auth-web-server ipaddress” on page 1007

•“auth-web-server page language” on page 1008

•“auth-web-server login-url” on page 1009

•“auth-web-server page logo” on page 1010

•“auth-web-server page sub-title” on page 1011

•“auth-web-server page success-message” on page 1012

•“auth-web-server page title” on page 1013

•“auth-web-server page welcome-message” on page 1014

•“auth-web-server ping-poll enable” on page 1015

•“auth-web-server ping-poll failcount” on page 1016

•“auth-web-server ping-poll interval” on page 1017

•“auth-web-server ping-poll reauth-timer-refresh” on page 1018

•“auth-web-server ping-poll timeout” on page 1019

•“auth-web-server port” on page 1020

•“auth-web-server redirect-delay-time” on page 1021

•“auth-web-server redirect-url” on page 1022

•“auth-web-server session-keep” on page 1023

•“auth-web-server ssl” on page 1024

613-50137-01 Rev A Command Reference for FS980M Series 944

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

•“auth-web-server ssl intercept-port” on page 1025

•“copy proxy-autoconfig-file” on page 1026

•“copy web-auth-https-file” on page 1027

•“description (Authentication Profile)” on page 1028

•“erase proxy-autoconfig-file” on page 1029

•“erase web-auth-https-file” on page 1030

•“platform l3-vlan-hashing-algorithm” on page 1031

•“platform mac-vlan-hashing-algorithm” on page 1032

•“show auth” on page 1033

•“show auth diagnostics” on page 1035

•“show auth interface” on page 1037

•“show auth sessionstatistics” on page 1040

•“show auth statistics interface” on page 1041

•“show auth supplicant” on page 1042

•“show auth supplicant interface” on page 1045

•“show auth two-step supplicant brief” on page 1046

•“show auth-web-server” on page 1047

•“show auth-web-server page” on page 1048

•“show proxy-autoconfig-file” on page 1049

613-50137-01 Rev A Command Reference for FS980M Series 945

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH AUTH-FAIL VLAN

auth auth-fail vlan

Overview Use this command to enable the auth-fail vlan feature on the specified vlan

interface. This feature assigns supplicants (client devices) to the specified VLAN if

they fail port authentication.

Use the no variant of this command to disable the auth-fail vlan feature for a

specified VLAN interface.

Syntax auth auth-fail vlan <1-4094>

no auth auth-fail vlan

Default The auth-fail vlan feature is disabled by default.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Usage Use the auth-fail vlan feature when using Web-Authentication instead of the Guest

VLAN feature, when you need to separate networks where one supplicant (client

device) requires authentication and another supplicant does not require

authentication from the same interface.

This is because the DHCP lease time using the Web-Authentication feature is

shorter, and the auth-fail vlan feature enables assignment to a different VLAN if a

supplicant fails authentication.

To enable the auth-fail vlan feature with Web Authentication, you need to set the

Web Authentication Server virtual IP address by using the auth-web-server

ipaddress command or the auth-web-server dhcp ipaddress command.

When using 802.1X port authentication, use a dot1x max-auth-fail command to set

the maximum number of login attempts. Three login attempts are allowed by

default for 802.1X port authentication before supplicants trying to authenticate

are moved from the Guest VLAN to the auth-fail VLAN. See the dot1x max-auth-fail

on page 915 for command information.

See the AAA and Port Authentication Feature Overview and Configuration Guide

for information about:

• the auth-fail VLAN feature, which allows the Network Administrator to

separate the supplicants who attempted authentication, but failed, from the

supplicants who did not attempt authentication, and

• restrictions regarding combinations of authentication enhancements

working together

Use appropriate ACLs (Access Control Lists) on interfaces for extra security if a

supplicant allocated to the designated auth-fail vlan can access the same network

Parameter Description

<1-4094>Assigns the VLAN ID to any supplicants that have failed port

authentication.

613-50137-01 Rev A Command Reference for FS980M Series 946

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH AUTH-FAIL VLAN

as a supplicant on the Guest VLAN. For more information about ACL concepts, and

configuring ACLs see the ACL Feature Overview and Configuration Guide. For

more information about ACL commands see:

•IPv4 Hardware Access Control List (ACL) Commands

•IPv4 Software Access Control List (ACL) Commands

•IPv6 Software Access Control List (ACL) Commands

Examples To enable the auth-fail vlan feature for port1.0.2 and assign VLAN 100, use the

following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth auth-fail vlan 100

To disable the auth-fail vlan feature for port1.0.2, use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth auth-fail vlan

To enable the auth-fail vlan feature on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth auth-fail vlan 100

To disable the auth-fail vlan feature on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth auth-fail vlan

Commands

auth profile (Global Configuration)

dot1x max-auth-fail

show dot1x

show dot1x interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 947

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH CRITICAL

auth critical

Overview This command enables the critical port feature on the interface. When the critical

port feature is enabled on an interface, and all the RADIUS servers are unavailable,

then the interface becomes authorized.

The no variant of this command disables critical port feature on the interface.

Syntax auth critical

no auth critical

Default The critical port of port authentication is disabled.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Examples To enable the critical port feature on interface port1.0.2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth critical

To disable the critical port feature on interface port1.0.2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth critical

To enable the critical port feature on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth critical

To disable the critical port feature on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth critical

Commands

auth profile (Global Configuration)

show auth-web-server

show dot1x

show dot1x interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 948

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH DYNAMIC-VLAN-CREATION

auth dynamic-vlan-creation

Overview This command enables and disables the Dynamic VLAN assignment feature.

The Dynamic VLAN assignment feature allows a supplicant (client device) to be

placed into a specific VLAN based on information returned from the RADIUS server

during authentication, on a given interface.

Use the no variant of this command to disable the Dynamic VLAN assignment

feature.

Syntax auth dynamic-vlan-creation [rule {deny|permit}] [type

{multi|single}]

no auth dynamic-vlan-creation

Default By default, the Dynamic VLAN assignment feature is disabled.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Usage If the Dynamic VLAN assignment feature is enabled (disabled by default), VLAN

assignment is dynamic. If the Dynamic VLAN assignment feature is disabled then

RADIUS attributes are ignored and configured VLANs are assigned to ports.

Dynamic VLANs may be associated with authenticated MAC addresses if the type

parameter is applied with the rule parameter.

The rule parameter deals with the case where there are multiple supplicants

attached to a port, and the type parameter has been set to single-vlan. The

parameter specifies how the switch should act if different VLAN IDs end up being

assigned to different supplicants. The keyword value deny means that once a

given VID has been assigned to the first supplicant, then if any subsequent

supplicant is assigned a different VID, that supplicant is rejected. The keyword

value permit means that once a given VID has been assigned to the first

supplicant, then if any subsequent supplicant is assigned a different VID, that

supplicant is accepted, but it is actually assigned the same VID as the first

supplicant.

Parameter Description

rule VLAN assignment rule.

deny Deny a differently assigned VLAN ID. This is the default rule.

permit Permit a differently assigned VLAN ID.

type Specifies whether multiple different VLANs can be assigned to

supplicants (client devices) attached to the port, or whether only a

single VLAN can be assigned to supplicants on the port.

multi Multiple Dynamic VLAN.

single Single Dynamic VLAN.

613-50137-01 Rev A Command Reference for FS980M Series 949

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH DYNAMIC-VLAN-CREATION

If you issue an auth dynamic-vlan-creation command without a rule parameter

then a second supplicant with a different VLAN ID is rejected. It is not assigned to

the first supplicant’s VLAN. Issuing an auth dynamic-vlan-creation command

without a rule parameter has the same effect as issuing an auth

dynamic-vlan-creation rule deny command rejecting supplicants with differing

VIDs.

The type parameter specifies whether multiple different VLANs can be assigned to

supplicants attached to the port, or whether only a single VLAN can be assigned to

supplicants on the port. The type parameter can select the port base VLAN or the

MAC base VLAN from the RADIUS VLAN ID. This can be used when the host-mode

is set to multi-supplicant. For single-host ports, the VLAN ID will be assigned to the

port. It is not supported with the Guest VLAN feature. Display the ID assigned using

a show vlan command. For multi-host ports, the VLAN ID will be assigned to the

MAC address of the authenticated supplicant. The VLAN ID assigned for the MAC

Base VLAN is displayed using the show platform table vlan command.

To configure Dynamic Vlan with Web Authentication, you need to set Web

Authentication Server virtual IP address by using the auth-web-server ipaddress

command or the auth-web-server dhcp ipaddress command. You also need to

create a hardware access-list that can be applied to the switch port interface.

You need to configure an IPv4 address for the VLAN interface on which Web

Authentication is running.

Examples To enable the Dynamic VLAN assignment feature on interface port1.0.2, use

the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# switchport access vlan 10

awplus(config-if)# auth-web enable

awplus(config-if)# auth dynamic-vlan-creation

awplus(config-if)# interface vlan10

awplus(config-if)# ip address 10.1.1.1/24

To enable the Dynamic VLAN assignment feature with Web Authentication on

interface port1.0.2 when Web Authentication is needed, use the commands:

awplus# configure terminal

awplus(config)# auth-web-server ipaddress 1.2.3.4

awplus(config)# access-list hardware acl-web send-to-cpu ip any

1.2.3.4

awplus(config)# interface port1.0.2

awplus(config-if)# auth-web enable

awplus(config-if)# auth dynamic-vlan-creation

awplus(config-if)# access-group acl-web

awplus(config-if)# interface vlan1

awplus(config-if)# ip address 10.1.1.1/24

613-50137-01 Rev A Command Reference for FS980M Series 950

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH DYNAMIC-VLAN-CREATION

To disable the Dynamic VLAN assignment feature on interface port1.0.2, use

the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth dynamic-vlan-creation

To enable the Dynamic VLAN assignment feature on authentication profile

‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth dynamic-vlan-creation

To disable the Dynamic VLAN assignment feature on authentication profile

‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth dynamic-vlan-creation

Validation

Commands

show dot1x

show dot1x interface

show running-config

Commands

auth profile (Global Configuration)

auth host-mode

613-50137-01 Rev A Command Reference for FS980M Series 951

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH GUEST-VLAN

auth guest-vlan

Overview This command enables and configures the Guest VLAN feature on the interface

specified by associating a Guest VLAN with an interface. This command does not

start authentication. The supplicant's (client device’s) traffic is associated with the

native VLAN of the interface if its not already associated with another VLAN. The

routing option enables routing from the Guest VLAN to another VLAN, so the

switch can lease DHCP addresses and accept access to a limited network.

The no variant of this command disables the guest VLAN feature on the interface

specified.

Syntax auth guest-vlan <1-4094> [routing]

no auth guest-vlan [routing]

Default The Guest VLAN authentication feature is disabled by default.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Usage The Guest VLAN feature may be used by supplicants (client devices) that have not

attempted authentication, or have failed the authentication process. Note that if a

port is in multi-supplicant mode with per-port dynamic VLAN configuration, after

the first successful authentication, subsequent hosts cannot use the guest VLAN

due to the change in VLAN ID. This may be avoided by using per-user dynamic

VLAN assignment.

When using the Guest VLAN feature with the multi-host mode, a number of

supplicants can communicate via a guest VLAN before authentication. A

supplicant’s traffic is associated with the native VLAN of the specified switch port.

The supplicant must belong to a VLAN before traffic from the supplicant can be

associated.

Note that you must enable 802.1X on the port and define a VLAN using the vlan

command before you can configure it as a guest VLAN.

Roaming Authentication cannot be enabled if DHCP snooping is enabled (service

dhcp-snooping command), and vice versa.

The Guest VLAN feature in previous releases had some limitations that have been

removed. Until this release the Guest VLAN feature could not lease the IP address

to the supplicant using DHCP Server or DHCP Relay features unless

Web-Authentication was also applied. When using NAP authentication, the

supplicant should have been able to log on to a domain controller to gain

certification, but the Guest VLAN would not accept access to another VLAN.

Parameter Description

<1-4094>VLAN ID (VID).

routing Enables routing from the Guest VLAN to other VLANs.

613-50137-01 Rev A Command Reference for FS980M Series 952

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH GUEST-VLAN

The Guest VLAN routing mode in this release overcomes these issues. With the

Guest VLAN routing mode, the switch can lease DHCP addresses and accept access

to a limited network.

Note that Guest VLAN can use only untagged ports.

See the AAA and Port Authentication Feature Overview and Configuration Guide

for information about:

• Guest VLAN, and

• restrictions regarding combinations of authentication enhancements

working together

Examples To define vlan100 and assign the guest VLAN feature to vlan100 on interface

port1.0.2, and enable routing from the guest VLAN to other VLANs, use the

following commands:

awplus# configure terminal

awplus(config)# vlan database

awplus(config-vlan)# vlan 100

awplus(config-vlan)# exit

awplus(config)# interface port1.0.2

awplus(config-if)# dot1x port-control auto

awplus(config-if)# auth guest-vlan 100 routing

To disable the guest VLAN feature on port1.0.2, use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth guest-vlan

To define vlan100 and assign the guest VLAN feature to vlan100 on authentication

profile ‘student’, use the commands:

awplus# configure terminal

awplus(config)# vlan database

awplus(config-vlan)# vlan 100

awplus(config-vlan)# exit

awplus(config)# auth profile student

awplus(config-auth-profile)# auth guest-vlan 100

To disable the guest VLAN feature on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth guest-vlan

Commands

auth profile (Global Configuration)

613-50137-01 Rev A Command Reference for FS980M Series 953

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH GUEST-VLAN

auth guest-vlan forward

dot1x port-control

show dot1x

show dot1x interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 954

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH GUEST-VLAN FORWARD

auth guest-vlan forward

Overview Use this command to enable packet forwarding from the Guest VLAN to a

destination IP address or subnet. If this command is configured, the device can

lease DHCP addresses and accept access to a limited part of your network. Also,

when using NAP authentication, the supplicant can log on to a domain controller

to gain certification.

Use the no variant of this command to disable packet forwarding from the Guest

VLAN to a destination IP address or subnet.

Syntax auth guest-vlan forward {<ip-address>|<ip-address/mask>}

[dns|tcp <1-65535>|udp <1-65535>]

no auth guest-vlan forward {<ip-address>|<ip-address/mask>}

[dns|tcp <1-65535>|udp <1-65535>]

Default Forwarding is disabled by default.

Mode Interface Configuration mode for a specified switch port, or Authentication Profile

mode

Usage Before using this command, you must configure the guest VLAN with the auth

guest-vlan command.

Example To enable packet forwarding from the guest VLAN to the destination IP address on

interface port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth guest-vlan forward 10.0.0.1

To enable forwarding of DNS packets from the guest VLAN to the destination IP

address on interface port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth guest-vlan forward 10.0.0.1 dns

Parameter Description

<ip-address>

<ip-address/



mask>

The IP address or subnet to which the guest VLAN can forward

packets, in dotted decimal notation

dns Enable forwarding of DNS packets

tcp <1-65535>Enable forwarding of packets for the specified TCP port number

udp <1-65535>Enable forwarding of packets for the specified UDP port number

613-50137-01 Rev A Command Reference for FS980M Series 955

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH GUEST-VLAN FORWARD

To disable forwarding of DNS packets from the guest VLAN to the destination IP

address on port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth guest-vlan forward 10.0.0.1 dns

To enable the tcp forwarding port 137 on authentication profile 'student', use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth guest-vlan forward 10.0.0.1

tcp 137

To disable the tcp forwarding port 137 authentication profile 'student', use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth guest-vlan forward

10.0.0.1 tcp 137

Commands

auth guest-vlan

auth profile (Global Configuration)

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 956

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH HOST-MODE

auth host-mode

Overview This command selects the host mode on the specified interface.

Use the no variant of this command to set host mode to the default setting (single

host).

Syntax auth host-mode {single-host|multi-host|multi-supplicant}

no auth host-mode

Default The default host mode for port authentication is for a single host.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Usage Ports residing in the unauthorized state for host(s) or supplicant(s), change to an

authorized state when the host or supplicant has successfully authenticated with

the Authentication Server.

When multi-host mode is used or auth critical feature is used, all hosts do not need

to be authenticated.

Examples To set the host mode to multi-supplicant on interface port1.0.2, use the

following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth host-mode multi-supplicant

Parameter Description

single-host Single host mode. In this mode, only one host may be

authorized with the port. If other hosts out the interface

attempt to authenticate, the authenticator blocks the

attempt.

multi-host Multi host mode. In this mode, multiple hosts may be

authorized with the port; however only one host must be

successfully authenticated at the Authentication Server for

all hosts to be authorized with the port. Upon one host being

successfully authenticated (state Authenticated), the other

hosts will be automatically authorized at the port (state

ForceAuthorized). If no host is successfully authenticated,

then all hosts are not authorized with the port.

multi-supplicant Multi supplicant (client device) mode. In this mode, multiple

hosts may be authorized with the port, but each host must

be individually authenticated with the Authentication Server

to be authorized with the port. Supplicants which are not

authenticated are not authorized with the port, while

supplicants which are successfully authenticated are

authorized with the port.

613-50137-01 Rev A Command Reference for FS980M Series 957

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH HOST-MODE

To set the host mode to default (single host) on interface port1.0.2, use the

following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth host-mode

To set the host mode to multi-supplicant on authentication profile ‘student’, use

the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth host-mode multi-supplicant

To set the host mode to default (single host) on authentication profile ‘student’,

use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth host-mode

Commands

auth profile (Global Configuration)

show dot1x

show dot1x interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 958

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH LOG

auth log

Overview Use this command to configure the types of authentication feature log messages

that are output to the log file.

Use the no variant of this command to remove either specified types or all types of

authentication feature log messages that are output to the log file.

Syntax auth log {dot1x|auth-mac|auth-web}

{success|failure|logoff|all}

no auth log {do1x|auth-mac|auth-web}

{success|failure|logoff|all}

Default All types of authentication log messages are output to the log file by default.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Examples To configure the logging of MAC authentication failures to the log file for

supplicants (client devices) connected to interface port1.0.2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth log auth-mac failure

Parameter Description

dot1x Specify only 802.1X-Authentication log messages are output to the log

file.

auth-mac Specify only MAC-Authentication log messages are output to the log

file.

auth-web Specify only Web-Authentication log messages are output to the log

file.

success Specify only successful authentication log messages are output to the

log file.

failure Specify only authentication failure log messages are output to the log

file.

logoff Specify only authentication log-off messages are output to the log file.

Note that link down, age out and expired ping polling messages will be

included.

all Specify all types of authentication log messages are output to the log

file Note that this is the default behavior for the authentication logging

feature.

613-50137-01 Rev A Command Reference for FS980M Series 959

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH LOG

To disable the logging of all types of authentication log messages to the log file for

supplicants (client devices) connected to interface port1.0.2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth log all

To configure the logging of web authentication failures to the log file for

supplicants (client devices) connected to authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth log auth-web failure

To disable the logging of all types of authentication log messages to the log file for

supplicants (client devices) connected to authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth log all

Commands

auth profile (Global Configuration)

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 960

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH MAX-SUPPLICANT

auth max-supplicant

Overview This command sets the maximum number of supplicants (client devices) that can

be authenticated on the selected port. Once this value is exceeded, further

supplicants will not be authenticated.

The no variant of this command resets the maximum supplicant number to the

default.

Syntax auth max-supplicant <2-1024>

no auth max-supplicant

Default The max supplicant of port authentication is 1024.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Examples To set the maximum number of supplicants to 10 on interface port1.0.2, use

the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth max-supplicant 10

To reset the maximum number of supplicant to default on interface port1.0.2,

use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth max-supplicant

To set the maximum number of supplicants to 10 on authentication profile

‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth max-supplicant 10

To reset the maximum number of supplicant to default on authentication profile

‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth max-supplicant

Parameter Description

<2-1024>Limit number.

613-50137-01 Rev A Command Reference for FS980M Series 961

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH MAX-SUPPLICANT

Commands

auth profile (Global Configuration)

show dot1x

show dot1x interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 962

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH PROFILE (GLOBAL CONFIGURATION)

auth profile (Global Configuration)

Overview Use this command to enter port authentication profile mode and configure a port

authentication profile.

If the specified profile does not exist a new authentication profile is created with

the name provided.

Use the no variant of this command to delete the specified port authentication

profile.

Syntax auth profile <profile-name>

no auth profile <profile-name>

Default No port authentication profiles are created by default.

Mode Global Configuration

Usage A port authentication profile is a configuration object that aggregates multiple

port authentication commands. These profiles are attached or detached from an

interface using the auth profile (Interface Configuration) command.

Example To create a new authentication profile ‘student’, use the following commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)#

To delete an authentication profile ‘student’, use the following commands:

awplus# configure terminal

awplus(config)# no auth profile student

Commands

auth profile (Interface Configuration)

description (Authentication Profile)

Parameter Description

<varname>Name of the profile to create or configure.

613-50137-01 Rev A Command Reference for FS980M Series 963

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH PROFILE (INTERFACE CONFIGURATION)

auth profile (Interface Configuration)

Overview Use this command to attach a port authentication profile to the current interface.

Use the no variant of this command to detach a port authentication profile from

the current interface.

Syntax auth profile <profile-name>

no auth profile <profile-name>

Default No profile is attached by default.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port.

Usage This command attaches a authentication profile, created using the auth profile

(Global Configuration) command, to a static channel, a dynamic (LACP) channel

group, or a switch port.

You can only attach one profile to an interface at a time, use the no variant of the

command to detach a profile before attempting to attach another one.

Example To attach the authentication profile ‘student’ to port1.0.1, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.1

awplus(config-if)# auth profile student

To detach the authentication profile ‘student’ from port1.0.1, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.1

awplus(config-if)# no auth profile student

Commands

auth profile (Global Configuration)

Parameter Description

<profile-name>The name of the profile to attach to the current interface.

613-50137-01 Rev A Command Reference for FS980M Series 964

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH REAUTHENTICATION

auth reauthentication

Overview This command enables re-authentication on the interface specified in the Interface

mode, which may be a static channel group (or static aggregator) or a dynamic (or

LACP) channel group or a switch port.

Use the no variant of this command to disables reauthentication on the interface.

Syntax auth reauthentication

no auth reauthentication

Default Reauthentication of port authentication is disabled by default.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Examples To enable reauthentication on interface port1.0.2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth reauthentication

To disable reauthentication on interface port1.0.2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth reauthentication

To enable reauthentication on authentication profile ‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth reauthentication

To disable reauthentication on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth reauthentication

Commands

auth profile (Global Configuration)

show dot1x

show dot1x interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 965

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH ROAMING DISCONNECTED

auth roaming disconnected

Overview This command allows a supplicant to move to another authenticating interface

without reauthentication, even if the link is down for the interface that the

supplicant is currently connected to.

You must enter the auth roaming enable command on both interfaces before

using this command.

The no variant of this command disables roaming authentication on interfaces

that are link-down, and forces a supplicant to be reauthenticated when moving

between interfaces.

See the AAA and Port Authentication Feature Overview and Configuration Guide

for further information about this feature.

Syntax auth roaming disconnected

no auth roaming disconnected

Default By default, the authentication status for a roaming supplicant is deleted when an

interface goes down, so supplicants must reauthenticate.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Usage Note that 802.1X port authentication, MAC-authentication, or Web-authentication

must be configured before using this feature. The port that the supplicant is

moving to must have the same authentication configuration as the port the

supplicant is moving from.

Roaming Authentication cannot be enabled if DHCP snooping is enabled (service

dhcp-snooping command), and vice versa.

Examples To allow supplicants to move from port1.0.2 without reauthentication even when

the link is down, when using 802.1X authentication, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# dot1x port-control auto

awplus(config-if)# auth roaming enable

awplus(config-if)# auth roaming disconnected

To require supplicants to reauthenticate when moving from port1.0.2 if the link is

down, when using 802.1X authentication, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth roaming disconnected

613-50137-01 Rev A Command Reference for FS980M Series 966

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH ROAMING DISCONNECTED

To allow supplicants using authentication profile ‘student’ to move between ports

without reauthentication even when the link is down, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth roaming disconnected

To require supplicants using authentication profile ‘student’ to reauthenticate

when moving between ports if the link is down, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth roaming disconnected

Commands

auth profile (Global Configuration)

auth-mac enable

auth roaming enable

auth-web enable

dot1x port-control

show auth interface

show dot1x interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 967

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH ROAMING ENABLE

auth roaming enable

Overview This command allows a supplicant to move to another authenticating interface

without reauthentication, providing the link is up for the interface that the

supplicant is is currently connected to.

The no variant of this command disables roaming authentication on an interface,

and forces a supplicant to be reauthenticated when moving between interfaces.

See the AAA and Port Authentication Feature Overview and Configuration Guide

for further information about this feature.

Syntax auth roaming enable

no auth roaming enable

Default Roaming authentication is disabled by default.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Usage Note that 802.1X port authentication, MAC-authentication, or Web-authentication

must be configured before using this feature. The port that the supplicant is

moving to must have the same authentication configuration as the port the

supplicant is moving from.

This command only enables roaming authentication for links that are up. If you

want roaming authentication on links that are down, you must also use the

command auth roaming disconnected.

Roaming Authentication cannot be enabled if DHCP snooping is enabled (service

dhcp-snooping command), and vice versa.

Examples To enable roaming authentication for port1.0.4, when using 802.1X

authentication, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# dot1x port-control auto

awplus(config-if)# auth roaming enable

To disable roaming authentication for port1.0.4, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.4

awplus(config-if)# no auth roaming enable

To enable roaming authentication for authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth roaming enable

613-50137-01 Rev A Command Reference for FS980M Series 968

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH ROAMING ENABLE

To disable roaming authentication for authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth roaming enable

Commands

auth profile (Global Configuration)

auth-mac enable

auth roaming disconnected

auth-web enable

dot1x port-control

show auth interface

show dot1x interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 969

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH SUPPLICANT-IP

auth supplicant-ip

Overview This command adds a supplicant (client device) IP address on a given interface and

provides parameters for its configuration.

Use the no variant of this command to delete the supplicant IP address and reset

other parameters to their default values. The IP address can be determined before

authentication for only auth-web client.

Syntax auth supplicant-ip <ip-addr> [max-reauth-req <1-10>]

[port-control {auto|force-authorized|force-unauthorized}]

[quiet-period <1-65535>] [reauth-period <1-4294967295>]

[supp-timeout <1-65535>] [server-timeout <1-65535>]

[reauthentication]

no auth supplicant-ip <ip-addr> [reauthentication]

Parameter Description

<ip-addr>IP address of the supplicant entry in A.B.C.D/P format.

max-reauth-req The number of reauthentication attempts before

becoming unauthorized.

<1-10>Count of reauthentication attempts (default 2).

port-control Port control commands.

auto A port control parameter that allows port clients to

negotiate authentication.

force-authorized A port control parameter that forces the port state to

authorized.

force-unauthorized A port control parameter that forces the port state to

unauthorized.

quiet-period Quiet period during which the port remains in the HELD

state (default 60 seconds).

<1-65535>Seconds for quiet period.

reauth-period Seconds between reauthorization attempts (default 3600

seconds).

<1-4294967295>Seconds for reauthorization attempts (reauth-period).

supp-timeout Supplicant response timeout.

<1-65535>Seconds for supplicant response timeout (default 30

seconds).

server-timeout The period, in seconds, before the authentication server

response times out.

<1-65535>The server-timeout period, in seconds, default 3600

seconds.

reauthentication Enable reauthentication on a port.

613-50137-01 Rev A Command Reference for FS980M Series 970

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH SUPPLICANT-IP

Default No supplicant IP address for port authentication exists by default until first created

with the auth supplicant-ip command. The defaults for parameters applied are as

shown in the table above.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, a

switch port, or Authentication Profile.

Examples To add the supplicant IP address 192.168.10.0/24 to force authorized port control

for interface port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth supplicant-ip 192.168.10.0/24

port-control force-authorized

To delete the supplicant IP address 192.168.10.0/24 for interface port1.0.2, use the

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth supplicant-ip 192.168.10.0/24

To disable reauthentication for the supplicant(s) IP address 192.168.10.0/24 for

interface port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth supplicant-ip 192.168.10.0/24

reauthentication

To add the supplicant IP address 192.168.10.0/24 to force authorized port control

for auth profile 'student', use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth supplicant-ip

192.168.10.0/24 port-control force-authorized

To disable reauthentication for the supplicant IP address 192.168.10.0/24, for auth

profile 'student', use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-if)# no auth supplicant-ip 192.168.10.0/24

reauthentication

Commands

show auth

show dot1x

show dot1x interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 971

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH SUPPLICANT-MAC

auth supplicant-mac

Overview This command adds a supplicant (client device) MAC address or MAC mask on a

given interface with the parameters as specified in the table below.

Use the no variant of this command to delete the supplicant MAC address and

reset other parameters to their default values.

Syntax auth supplicant-mac <mac-addr> [mask <mac-addr-mask>]

[max-reauth-req <1-10>] [port-control

{auto|force-authorized|force-unauthorized|skip-second-auth}]

[quiet-period <1-65535>] [reauth-period <1-4294967295>]

[supp-timeout <1-65535>] [server-timeout <1-65535>]

[reauthentication]

no auth supplicant-mac <mac-addr> [reauthentication]

Parameter Description

<mac-addr>MAC (hardware) address of the supplicant entry in

HHHH.HHHH.HHHH MAC address hexadecimal format.

mask A mask applied to MAC addresses in order to select only

those addresses containing a specific string.

<mac-addr-mask> The mask comprises a string of three (period separated)

bytes, where each byte comprises four hexadecimal

characters that will generally be either 1or 0. When the

mask is applied to a specific MAC address, a match is only

required for characters that correspond to a 1 in the mask.

Characters that correspond to a 0 in the mask are

effectively ignored.

In the examples section below, the mask ffff.ff00.0000 is

applied for the MAC address 0000.5E00.0000. The applied

mask will then match only those MAC addresses that begin

with 0000.5E (in this case the OUI component). The

remaining portion of the addresses (in this case the NIC

component) will be ignored.

port-control Port control commands.

auto Allow port client to negotiate authentication.

force-authorized Force port state to authorized.

force-unauthorized Force port state to unauthorized.

skip-second-auth Skip the second authentication.

quiet-period Quiet period in the HELD state (default 60 seconds).

<1-65535>Seconds for quiet period.

reauth-period Seconds between reauthorization attempts (default 3600

seconds).

<1-4294967295>Seconds for reauthorization attempts (reauth-period).

613-50137-01 Rev A Command Reference for FS980M Series 972

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH SUPPLICANT-MAC

Default No supplicant MAC address for port authentication exists by default until first

created with the auth supplicant-mac command. The defaults for parameters are

shown in the table above.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Examples To add the supplicant MAC address 0000.5E00.5343 to force authorized port

control for port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth supplicant-mac 0000.5E00.5343

port-control force-authorized

To apply the mask ffff.ff00.0000 in order to add any supplicant whose MAC address

begins with 000.5E, and then to force authorized port control for port 1.0.2, use the

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth supplicant-mac 0000.5E00.0000 mask

ffff.ff00.0000 port-control force-authorized

To delete the supplicant MAC address 0000.5E00.5343 for port1.0.2, use the

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth supplicant-mac 0000.5E00.5343

To reset reauthentication to disabled for the supplicant MAC address

0000.5E00.5343 for port1.0.2, use the commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth supplicant-mac 0000.5E00.5343

reauthentication

supp-timeout Supplicant response timeout (default 30 seconds).

<1-65535>Seconds for supplicant response timeout.

server-timeout Authentication server response timeout (default 30

seconds).

<1-65535>Seconds for authentication server response timeout.

reauthentication Enable reauthentication on a port.

max-reauth-req No of reauthentication attempts before becoming

unauthorized (default 2).

<1-10>Count of reauthentication attempts.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 973

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH SUPPLICANT-MAC

To add the supplicant MAC address 0000.5E00.5343 to force authorized port

control for authentication profile ‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth supplicant-mac

0000.5E00.5343 port-control force-authorized

To delete the supplicant MAC address 0000.5E00.5343 for authentication profile

‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth supplicant-mac

0000.5E00.5343

To disable reauthentication for the supplicant MAC address 0000.5E00.5343 for

authentication profile ‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth supplicant-mac

0000.5E00.5343 reauthentication

Commands

show auth

show dot1x

show dot1x interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 974

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH TIMEOUT CONNECT-TIMEOUT

auth timeout connect-timeout

Overview This command sets the connect-timeout period for the interface.

Use the no variant of this command to reset the connect-timeout period to the

default.

Syntax auth timeout connect-timeout <1-65535>

no auth timeout connect-timeout

Default The connect-timeout default is 30 seconds.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Usage This command is used for MAC- and Web-Authentication. If the connect-timeout

has lapsed and the supplicant has the state connecting, then the supplicant is

deleted. When auth-web-server session-keep or auth two-step enableis enabled,

we recommend you configure a longer connect-timeout period.

Examples To set the connect-timeout period to 3600 seconds for port1.0.2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth timeout connect-timeout 3600

To reset the connect-timeout period to the default (30 seconds) for port1.0.2, use

the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth timeout connect-timeout

To set the connect-timeout period to 3600 seconds for authentication profile

‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth timeout connect-timeout 3600

Parameter Description

<1-65535>Specifies the connect-timeout period (in seconds).

613-50137-01 Rev A Command Reference for FS980M Series 975

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH TIMEOUT CONNECT-TIMEOUT

To reset the connect-timeout period to the default (30 seconds) for authentication

profile ‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth timeout connect-timeout

Commands

auth profile (Global Configuration)

show dot1x

show dot1x interface

613-50137-01 Rev A Command Reference for FS980M Series 976

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH TIMEOUT QUIET-PERIOD

auth timeout quiet-period

Overview This command sets a time period for which another authentication request is not

accepted on a given interface, after an authentication request has failed.

Use the no variant of this command to reset the quiet period to the default.

Syntax auth timeout quiet-period <1-65535>

no auth timeout quiet-period

Default The quiet period for port authentication is 60 seconds.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Examples To set the quiet period to 10 seconds for interface port1.0.2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth timeout quiet-period 10

To reset the quiet period to the default (60 seconds) for interface port1.0.2, use the

following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth timeout quiet-period

To set the quiet period to 10 seconds for authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth timeout quiet-period 10

To reset the quiet period to the default (60 seconds) for authentication profile

‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth timeout quiet-period

Commands

auth profile (Global Configuration)

Parameter Description

<1-65535>Specifies the quiet period (in seconds).

613-50137-01 Rev A Command Reference for FS980M Series 977

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH TIMEOUT REAUTH-PERIOD

auth timeout reauth-period

Overview This command sets the timer for reauthentication on a given interface. The

re-authentication for the supplicant (client device) is executed at this timeout. The

timeout is only applied if the auth reauthentication command is applied.

Use the no variant of this command to reset the reauth-period parameter to the

default (3600 seconds).

Syntax auth timeout reauth-period <1-4294967295>

no auth timeout reauth-period

Default The default reauthentication period for port authentication is 3600 seconds, when

reauthentication is enabled on the port.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Examples To set the reauthentication period to 1 day for interface port1.0.2, use the

following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth timeout reauth-period 86400

To reset the reauthentication period to the default (3600 seconds) for interface

port1.0.2, use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth timeout reauth-period

To set the reauthentication period to 1 day for authentication profile ‘student’, use

the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth timeout reauth-period 86400

To reset the reauthentication period to the default (3600 seconds) for

authentication profile ‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth timeout reauth-period

Parameter Description

<1-4294967295>The reauthentication timeout period (in seconds).

613-50137-01 Rev A Command Reference for FS980M Series 978

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH TIMEOUT REAUTH-PERIOD

Commands

auth profile (Global Configuration)

auth reauthentication

show dot1x

show dot1x interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 979

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH TIMEOUT SERVER-TIMEOUT

auth timeout server-timeout

Overview This command sets the timeout for the waiting response from the RADIUS server

on a given interface.

The no variant of this command resets the server-timeout to the default (30

seconds).

Syntax auth timeout server-timeout <1-65535>

no auth timeout server-timeout

Default The server timeout for port authentication is 30 seconds.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Examples To set the server timeout to 120 seconds for interface port1.0.2, use the

following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth timeout server-timeout 120

To set the server timeout to the default (30 seconds) for interface port1.0.2, use

the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth timeout server-timeout

To set the server timeout to 120 seconds for authentication profile ‘student’, use

the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth timeout server-timeout 120

To set the server timeout to the default (30 seconds) for authentication profile

‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth timeout server-timeout

Parameter Description

<1-65535>Server timeout period (in seconds).

613-50137-01 Rev A Command Reference for FS980M Series 980

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH TIMEOUT SERVER-TIMEOUT

Commands

auth profile (Global Configuration)

show dot1x

show dot1x interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 981

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH TIMEOUT SUPP-TIMEOUT

auth timeout supp-timeout

Overview This command sets the timeout of the waiting response from the supplicant (client

device) on a given interface.

The no variant of this command resets the supplicant timeout to the default (30

seconds).

Syntax auth timeout supp-timeout <1-65535>

no auth timeout supp-timeout

Default The supplicant timeout for port authentication is 30 seconds.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Examples To set the server timeout to 2 seconds for interface port1.0.2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth timeout supp-timeout 2

To reset the server timeout to the default (30 seconds) for interface port1.0.2, use

the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth timeout supp-timeout

To set the server timeout to 2 seconds for authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth timeout supp-timeout 2

To reset the server timeout to the default (30 seconds) for authentication profile

‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth timeout supp-timeout

Parameter Description

<1-65535>The sup-timeout period (in seconds).

613-50137-01 Rev A Command Reference for FS980M Series 982

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH TIMEOUT SUPP-TIMEOUT

Commands

auth profile (Global Configuration)

show dot1x

show dot1x interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 983

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH TWO-STEP ENABLE

auth two-step enable

Overview This command enables a two-step authentication feature on an interface. When

this feature is enabled, the supplicant is authorized in a two-step process. If

authentication succeeds, the supplicant becomes authenticated. This command

will apply the two-step authentication method based on 802.1X-, MAC- or

Web-Authentication.

The no variant of this command disables the two-step authentication feature.

Syntax auth two-step enable

no auth two-step enable

Default Two step authentication is disabled by default.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Usage The single step authentication methods (either user or device authentication) have

a potential security risk:

• an unauthorized user can access the network with an authorized device, or

• an authorized user can access the network with an unauthorized device.

Two-step authentication solves this problem by authenticating both the user and

the device. The supplicant will only become authenticated if both these steps are

successful. If the first authentication step fails, then the second step is not started.

Examples To enable the two step authentication feature, use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth two-step enable

To disable the two step authentication feature, use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth two-step enable

To enable MAC-Authentication followed by 802.1X-Authentication, use the

following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# switchport mode access

awplus(config-if)# auth-mac enable

awplus(config-if)# dot1x port-control auto

awplus(config-if)# auth dynamic-vlan-creation

awplus(config-if)# auth two-step enable

613-50137-01 Rev A Command Reference for FS980M Series 984

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH TWO-STEP ENABLE

To enable MAC-Authentication followed by Web-Authentication, use the

following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# switchport mode access

awplus(config-if)# auth-mac enable

awplus(config-if)# auth-web enable

awplus(config-if)# auth dynamic-vlan-creation

awplus(config-if)# auth two-step enable

To enable 802.1X-Authentication followed by Web-Authentication, use the

following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# switchport mode access

awplus(config-if)# auth-web enable

awplus(config-if)# dot1x port-control auto

awplus(config-if)# auth dynamic-vlan-creation

awplus(config-if)# auth two-step enable

To enable the two step authentication feature for authentication profile ‘student’,

use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth two-step enable

To disable the two step authentication feature for authentication profile ‘student’,

use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth two-step enable

Validation

Commands

show startup-config

show auth supplicant

show dot1x supplicant

613-50137-01 Rev A Command Reference for FS980M Series 985

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH TWO-STEP ENABLE

Relat ed

Commands

auth profile (Global Configuration)

show auth two-step supplicant brief

show auth

show auth interface

show auth supplicant

show dot1x

show dot1x interface

show dot1x supplicant

613-50137-01 Rev A Command Reference for FS980M Series 986

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-MAC ENABLE

auth-mac enable

Overview This command enables MAC-based authentication on the interface specified in the

Interface command mode.

Use the no variant of this command to disable MAC-based authentication on an

interface.

Syntax auth-mac enable

no auth-mac enable

Default MAC-Authentication is disabled by default.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Usage Enabling spanning-tree edgeport on ports after enabling MAC-based

authentication avoids unnecessary re-authentication when the port state changes,

which does not happen when spanning tree edgeport is enabled. Note that

re-authentication is correct behavior without spanning-tree edgeport enabled.

Applying switchport mode access on ports is also good practice to set the ports

to access mode with ingress filtering turned on, whenever ports for

MAC-Authentication are in a VLAN.

Examples To enable MAC-Authentication on interface port1.0.2 and enable spanning

tree edgeport to avoid unnecessary re-authentication, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth-mac enable

awplus(config-if)# spanning-tree edgeport

awplus(config-if)# switchport mode access

To disable MAC-Authentication on interface port1.0.2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth-mac enable

To enable MAC authentication on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth-mac enable

613-50137-01 Rev A Command Reference for FS980M Series 987

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-MAC ENABLE

To disable MAC authentication on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth-mac enable

Commands

auth profile (Global Configuration)

show auth

show auth interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 988

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-MAC METHOD

auth-mac method

Overview This command sets the type of authentication method for MAC-Authentication

that is used with RADIUS on the interface specified in the Interface command

mode.

The no variant of this command resets the authentication method used to the

default method (PAP) as the RADIUS authentication method used by the

MAC-Authentication.

Syntax auth-mac method [eap-md5|pap]

no auth-mac method

Default The MAC-Authentication method is PAP.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Examples To set the MAC-Authentication method to pap on interface port1.0.2, use the

following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth-mac method pap

To set the MAC-Authentication method to the default on interface port1.0.2,

use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth-mac method

To enable MAC authentication on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth-mac enable

Parameter Description

eap-md5 Enable EAP-MD5 of authentication method.

pap Enable PAP of authentication method.

613-50137-01 Rev A Command Reference for FS980M Series 989

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-MAC METHOD

To disable MAC authentication on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth-mac enable

Commands

auth profile (Global Configuration)

show auth

show auth interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 990

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-MAC PASSWORD

auth-mac password

Overview This command changes the password for MAC-based authentication.

Use the no variant of this command to return the password to its default.

Syntax auth-mac [encrypted] password <password>

no auth-mac password

Default By default, the password is the MAC address of the supplicant

Mode Global Configuration

Usage Changing the password increases the security of MAC-based authentication,

because the default password is easy for an attacker to discover. This is particularly

important if:

• some MAC-based supplicants on the network are intelligent devices, such as

computers, and/or

• you are using two-step authentication (see the “Ensuring Authentication

Methods Require Different Usernames and Passwords” section of the AAA

and Port Authentication Feature_Overview and Configuration Guide).

Examples To change the password to verySecurePassword, use the commands:

awplus# configure terminal

awplus(config)# auth-mac password verySecurePassword

Validation

Command

show running-config

Commands

auth two-step enable

show auth

Parameter Description

auth-mac MAC-based authentication

encrypted Specify an encrypted password

password Configure the password

<password>The new password. Passwords can be up to 64 characters in length

and can contain any printable characters except

•?

• " (double quotes)

•space

613-50137-01 Rev A Command Reference for FS980M Series 991

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-MAC REAUTH-RELEARNING

auth-mac reauth-relearning

Overview This command sets the MAC address learning of the supplicant (client device) to

re-learning for re-authentication on the interface specified in the Interface

command mode.

Use the no variant of this command to disable the auth-mac re-learning option.

Syntax auth-mac reauth-relearning

no auth-mac reauth-relearning

Default Re-learning for port authentication is disabled by default.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Examples To enable the re-authentication re-learning feature on interface port1.0.2, use

the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth-mac reauth-relearning

To disable the re-authentication re-learning feature on interface port1.0.2, use

the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awpl us(config-if)# no auth-mac reauth-relearning

To enable the re-authentication re-learning feature on authentication profile

‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth-mac reauth-relearning

To disable the re-authentication re-learning feature on authentication profile

‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth-mac reauth-relearning

Commands

auth profile (Global Configuration)

show auth

show auth interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 992

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-MAC USERNAME

auth-mac username

Overview Use this command to specify the format of the MAC address in the username and

password field when a request for MAC-based authorization is sent to a RADIUS

server.

Syntax auth-mac username {ietf|unformatted} {lower-case|upper-case}

Default auth-mac username ietf lower-case

Mode Global Configuration

Usage This command is provided to allow other vendors’, AlliedWare, and AlliedWare

Plus switches to share the same format on the RADIUS server.

Example To configure the format of the MAC address in the username and password field to

be changed to IETF and upper-case, use the following commands:

awplus# configure terminal

awplus(config)# auth-mac username ietf upper-case

Commands

auth-mac username

show running-config

Parameter Description

ietf The MAC address includes a hyphen between each 2 bytes.

(Example: xx-xx-xx-xx-xx-xx)

unformatted The MAC address does not include hyphens. (Example:

xxxxxxxxxxxx)

lower-case The MAC address uses lower-case characters (a-f)

upper-case The MAC address uses upper-case characters (A-F)

613-50137-01 Rev A Command Reference for FS980M Series 993

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB ENABLE

auth-web enable

Overview This command enables Web-based authentication in Interface mode on the

interface specified.

Use the no variant of this command to apply its default.

Syntax auth-web enable

no auth-web enable

Default Web-Authentication is disabled by default.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Usage Web-based authentication cannot be enabled if DHCP snooping is enabled by

using the service dhcp-snooping command, and vice versa. You need to configure

an IPv4 address for the VLAN interface on which Web Authentication is running.

Examples To enable Web-Authentication on static-channel-group 2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# static-channel-group 2

awplus(config-if)# exit

awplus(config)# interface sa2

awplus(config-if)# auth-web enable

To disable Web-Authentication on static-channel-group 2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# static-channel-group 2

awplus(config-if)# exit

awplus(config)# interface sa2

awplus(config-if)# no auth-web enable

To enable Web authentication on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth-web enable

613-50137-01 Rev A Command Reference for FS980M Series 994

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB ENABLE

To disable Web authentication on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth-web enable

Commands

auth profile (Global Configuration)

show auth

show auth interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 995

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB FORWARD

auth-web forward

Overview This command enables the Web-authentication packet forwarding feature on the

interface specified. This command also enables ARP forwarding, and adds

forwarded packets to the tcp or udp port number specified.

The no variant of this command disables the specified packet forwarding feature

on the interface.

Syntax auth-web forward [<ip-address>|<ip-address/prefix-length>]

{dns|tcp <1-65535>|udp <1-65535>}

auth-web forward {arp|dhcp|dns|tcp <1-65535>|udp <1-65535>}

The no variant of this command are:

no auth-web forward [<ip-address>|<ip-address/prefix-length>]

{dns|tcp <1-65535>|udp <1-65535>}

no auth-web forward {arp|dhcp|dns|tcp <1-65535>|udp <1-65535>}

Default Packet forwarding for port authentication is enabled by default for “arp”, “dhcp”

and “dns”.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Usage For more information about the <ip-address> parameter, and an example, see the

“auth- web forward” section in the Alliedware Plus Technical Tips and Tricks.

Parameter Description

<ip-address>

<ip-address/



prefix-length>

The IP address or subnet on which the Web-authentication is to

be enabled.

arp Enable forwarding of ARP.

dhcp Enable forwarding of DHCP (67/udp).

dns Enable forwarding of DNS (53/udp).

tcp Enable forwarding of TCP specified port number.

<1-65535> TCP Port number.

udp Enable forwarding of UDP specified port number.

<1-65535> UDP Port number.

613-50137-01 Rev A Command Reference for FS980M Series 996

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB FORWARD

Examples To enable the ARP forwarding feature on interface port1.0.2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth-web forward arp

To add the TCP forwarding port 137 on interface port1.0.2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth-web forward tcp 137

To add the DNS Server IP address 192.168.1.10 on interface port1.0.2, use the

following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# switchport mode access

awplus(config-if)# auth-web enable

awplus(config-if)# auth dynamic-vlan-creation

awplus(config-if)# auth-web forward 192.168.1.10 dns

To disable the ARP forwarding feature on interface port1.0.2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth-web forward arp

To delete the TCP forwarding port 137 on interface port1.0.2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth-web forward tcp 137

To delete the all of TCP forwarding on interface port1.0.2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth-web forward tcp

To enable the arp forwarding feature on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth-web forward arp

613-50137-01 Rev A Command Reference for FS980M Series 997

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB FORWARD

To add the tcp forwarding port 137 on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth-web forward tcp 137

To disable the ARP forwarding feature on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth-web forward arp

To delete the tcp forwarding port 137 on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth-web forward tcp 137

To delete all tcp forwarding on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth-web forward tcp

Commands

auth profile (Global Configuration)

show auth

show auth interface

613-50137-01 Rev A Command Reference for FS980M Series 998

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB MAX-AUTH-FAIL

auth-web max-auth-fail

Overview This command sets the number of authentication failures allowed before rejecting

further authentication requests. When the supplicant (client device) fails more

than the specified number of times, then login requests are refused during the

quiet period.

The no variant of this command resets the maximum number of authentication

failures to the default.

Syntax auth-web max-auth-fail <0-10>

no auth-web max-auth-fail

Default The maximum number of authentication failures is set to 3.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Examples To set the lock count to 5 on interface port1.0.2, use the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth-web max-auth-fail 5

To set the lock count to the default on interface port1.0.2, use the following

commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# no auth-web max-auth-fail

To set the lock count to 5 on authentication profile ‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth-web max-auth-fail 5

To set the lock count to the default on authentication profile ‘student’, use the

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth-web max-auth-fail

Parameter Description

<0-10>The maximum number of authentication requests allowed

before failing.

613-50137-01 Rev A Command Reference for FS980M Series 999

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB MAX-AUTH-FAIL

Commands

auth profile (Global Configuration)

auth timeout quiet-period

show auth

show auth interface

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 1000

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB METHOD

auth-web method

Overview This command sets the Web-authentication access method that is used with

RADIUS on the interface specified.

The no variant of this command sets the authentication method to PAP for the

interface specified when Web-Authentication is also used with the RADIUS

authentication method.

Syntax auth-web method {eap-md5|pap}

no auth-web method

Default The Web-Authentication method is set to PAP by default.

Mode Interface Configuration for a static channel, a dynamic (LACP) channel group, or a

switch port; or Authentication Profile mode.

Example To set the Web-Authentication method to eap-md5 on interface port1.0.2, use

the following commands:

awplus# configure terminal

awplus(config)# interface port1.0.2

awplus(config-if)# auth-web method eap-md5

To set the web authentication method to eap-md5 for authentication profile

‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# auth-web method eap-md5

To reset the web authentication method to the default (PAP) for authentication

profile ‘student’, use the commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no auth-web method

Commands

auth profile (Global Configuration)

show auth

show auth interface

show running-config

Parameter Description

eap-md5 Enable EAP-MD5 as the authentication method.

pap Enable PAP as the authentication method.

613-50137-01 Rev A Command Reference for FS980M Series 1001

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER BLOCKING-MODE

auth-web-server blocking-mode

Overview Use this command to enable blocking mode for the Web-Authentication server.

The blocking mode displays an authentication success or failure screen

immediately from the response result from a RADIUS server.

Use the no variant of this command to disable blocking mode for the

Web-Authentication server.

Syntax auth-web-server blocking-mode

no auth-web-server blocking-mode

Default By default, blocking mode is disabled for the Web-Authentication server.

Mode Global Configuration

Example To enable blocking mode for the Web-Authentication server, use the following

commands:

awplus# configure terminal

awplus(config)# auth-web-server blocking-mode

To disable blocking mode for the Web-Authentication server, use the following

commands:

awplus# configure terminal

awplus(config)# no auth-web-server blocking-mode

Commands

auth-web-server redirect-delay-time

show auth-web-server

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 1002

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER DHCP IPADDRESS

auth-web-server dhcp ipaddress

Overview Use this command to assign an IP address and enable the DHCP service on the

Web-Authentication server for supplicants (client devices).

Use the no variant of this command to remove an IP address and disable the DHCP

service on the Web-Authentication server for supplicants.

Syntax auth-web-server dhcp ipaddress <ip-address/prefix-length>

no auth-web-server dhcp ipaddress

Default No IP address for the Web-Authentication server is set by default.

Mode Global Configuration

Usage See the AAA and Port Authentication Feature Overview and Configuration Guide

for information about:

• using DHCP with web authentication, and

• restrictions regarding combinations of authentication enhancements

working together

You cannot use the IPv4 address assigned to the device’s interface as the

Web-Authentication server address.

Examples To assign the IP address 10.0.0.1 to the Web-Authentication server, use the

following commands:

awplus# configure terminal

awplus(config)# auth-web-server dhcp ipaddress 10.0.0.1/8

To remove an IP address on the Web-Authentication server, use the following

commands:

awplus# configure terminal

awplus(config)# no auth-web-server dhcp ipaddress

Validation

Commands

show running-config

Commands

show auth-web-server

auth-web-server dhcp lease

Parameter Description

<ip-addr/

prefix-length>

The IPv4 address and prefix length assigned for the DHCP

service on the Web-Authentication server for supplicants.

613-50137-01 Rev A Command Reference for FS980M Series 1003

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER DHCP LEASE

auth-web-server dhcp lease

Overview Use this command to set the DHCP lease time for supplicants (client devices) using

the DHCP service on the Web-Authentication server.

Use the no variant of this command to reset to the default DHCP lease time for

supplicants using the DHCP service on the Web-Authentication server.

Syntax auth-web-server dhcp lease <20-60>

no auth-web-server dhcp lease

Default The default DHCP lease time for supplicants using the DHCP service on the Web-

Authentication server is set to 30 seconds.

Mode Global Configuration

Usage See the AAA and Port Authentication Feature Overview and Configuration Guide

for information about:

• using DHCP with web authentication, and

• restrictions regarding combinations of authentication enhancements

working together

Examples To set the DHCP lease time to 1 minute for supplicants using the DHCP service on

the Web-Authentication server, use the following commands:

awplus# configure terminal

awplus(config)# auth-web-server dhcp lease 60

To reset the DHCP lease time to the default setting (30 seconds) for supplicants

using the DHCP service on the Web-Authentication server, use the following

commands:

awplus# configure terminal

awplus(config)# no auth-web-server dhcp lease

Validation

Commands

show running-config

Commands

show auth-web-server

auth-web-server dhcp ipaddress

Parameter Description

<20-60>DHCP lease time for supplicants using the DHCP service on the Web-

Authentication server in seconds.

613-50137-01 Rev A Command Reference for FS980M Series 1004

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER DHCP-WPAD-OPTION

auth-web-server dhcp-wpad-option

Overview This command sets the DHCP WPAD (Web Proxy Auto-Discovery) option for the

Web-Authentication temporary DHCP service.

For more information and examples, see the “Web Auth Proxy” section in the

Alliedware Plus Technical Tips and Tricks.

Use the no variant of this command to disable the DHCP WPAD function.

Syntax auth-web-server dhcp wpad-option <url>

no auth-web-server dhcp wpad-option

Default The Web-Authentication server DHCP WPAD option is not set.

Mode Global Configuration

Usage If the supplicant is configured to use WPAD, the supplicant’s web browser will use

TCP port 80 as usual. Therefore, the packet can be intercepted by

Web-Authentication as normal, and the Web-Authentication Login page can be

sent. However, after authentication, the browser does not know where to get the

WPAD file and so cannot access external web pages. The WPAD file is usually

named proxy.pac file and tells the browser what web proxy to use.

Use this command to tell the supplicant where it can get this file from. The switch

itself can be specified as the source for this file, and it can deliver it to the

supplicant on request.

Example To specify that the proxy.pac file is found on the server at 192.168.1.100, use the

following commands:

awplus# configure terminal

awplus(config)# auth-web-server dhcp wpad-option

http://192.168.1.100/proxy/proxy.pac

Commands

show auth-web-server

Parameter Description

<url>URL to the server which gets a .pac file.

613-50137-01 Rev A Command Reference for FS980M Series 1005

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER HOST-NAME

auth-web-server host-name

Overview This command assigns a hostname to the web authentication server.

Use the no variant of this command to remove the hostname from the web

authentication server.

Syntax auth-web-server host-name <hostname>

no auth-web-server host-name

Default The web authentication server has no hostname.

Mode Global Configuration

Usage When the web authentication server uses HTTPS protocol, the web browser will

validate the certificate. If the certificate is invalid, the web page gives a warning

message before displaying server content. However, the web page will not give

warning message if the server has a hostname same as the one stored in the

installed certificate.

Examples To set the auth.example.com as the hostname of the web authentication server,

use the commands:

awplus# configure terminal

awplus(config)# auth-web-server host-name auth.example.com

To remove hostname auth.example.com from the web authentication server, use

the commands:

awplus# configure terminal

awplus(config)# no auth-web-server host-name

Commands

aaa authentication auth-web

auth-web enable

Parameter Description

<hostname>URL string of the hostname

613-50137-01 Rev A Command Reference for FS980M Series 1006

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER INTERCEPT-PORT

auth-web-server intercept-port

Overview This command specifies any additional TCP port numbers that the

Web-Authentication server is to intercept.

Use the no variant of this command to stop intercepting the TCP port numbers.

Syntax auth-web-server intercept-port {<1-65535>|any}

no auth-web-server intercept-port {<1-65535>|any}

Default No additional TCP port numbers are intercepted by default.

Mode Global Configuration

Usage If this command is not specified, AlliedWare Plus Web-Authentication intercepts

the supplicant’s initial TCP port 80 connection to a web page and sends it the Web-

Authentication Login page. However, if the supplicant is configured to use a web

proxy, then it will usually be using TCP port 8080 (or another user configured port

number). In this case Web-Authentication cannot intercept the connection.

To overcome this limitation you can use this command to tell the switch which

additional port it should intercept, and then send the Web-Authentication Login

page to the supplicant.

When the web authentication switch is in a guest network, the switch does not

know the proxy server’s port number in the supplicant’s proxy setting. To

overcome this limitation, you can use the any option in this command to intercept

all TCP packets.

When you use this command in conjunction with a proxy server configured in the

web browser, you must add the proxy server’s network as a ‘No Proxy’ network.

You can specify ‘No Proxy’ networks in the proxy settings in your web browser. For

more information, see the “Web Auth Proxy” section in the Alliedware Plus

Technical Tips and Tricks.

Example To additionally intercept port number 3128, use the following commands:

awplus# configure terminal

awplus(config)# auth-web-server intercept-port 3128

Commands

show auth-web-server

Parameter Description

<1-65535>TCP port number.

any Intercept all TCP packets

613-50137-01 Rev A Command Reference for FS980M Series 1007

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER IPADDRESS

auth-web-server ipaddress

Overview This command sets the IP address for the Web-Authentication server.

Use the no variant of this command to delete the IP address for the

Web-Authentication server.

You cannot use the IPv4 address assigned to the device’s interface as the

Web-Authentication server address.

Syntax auth-web-server ipaddress <ip-address>

no auth-web-server ipaddress

Default The Web-Authentication server address on the system is not set by default.

Mode Global Configuration

Examples To set the IP address 10.0.0.1 to the Web-Authentication server, use the

following commands:

awplus# configure terminal

awplus(config)# auth-web-server ipaddress 10.0.0.1

To delete the IP address from the Web-Authentication server, use the following

commands:

awplus# configure terminal

awplus(config)# no auth-web-server ipaddress

Validation

Commands

show auth

show auth-web-server

show running-config

Parameter Description

<ip-address>Web-Authentication server dotted decimal IP address in

A.B.C.D format.

613-50137-01 Rev A Command Reference for FS980M Series 1008

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER PAGE LANGUAGE

auth-web-server page language

Overview Use this command to set the presentation language of Web authentication pages.

Titles and subtitles of Web authentication pages will be set accordingly. Note that

presently only English or Japanese are offered.

Use the no variant of this command to set the presentation language of Web

authentication pages to its default (English).

Syntax auth-web-server page language {english|japanese}

no auth-web-server page language

Default Web authentication pages are presented in English by default.

Mode Global Configuration

Examples To set Japanese as the presentation language of Web authentication pages, use

the following commands:

awplus# configure terminal

awplus(config)# auth-web-server page language japanese

To set English as the presentation language of Web authentication pages, use the

following commands:

awplus# configure terminal

awplus(config)# auth-web-server page language english

To unset the presentation language of Web authentication pages and use English

as the default presentation language, use the following commands:

awplus# configure terminal

awplus(config)# no auth-web-server page language

Commands

auth-web-server page title

auth-web-server page sub-title

show auth-web-server page

Parameter Description

english Web authentication pages are presented in English.

japanese Web authentication pages are presented in Japanese.

613-50137-01 Rev A Command Reference for FS980M Series 1009

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER LOGIN-URL

auth-web-server login-url

Overview This command sets the web-authentication login page URL. This lets you replace

the login page with your own page. See “Customising the Login Page” in the AAA

and Port Authentication Feature Overview and Configuration Guide for details.

Use the no variant of this command to delete the URL.

Syntax auth-web-server login-url <URL>

no auth-web-server login-url

Default The built-in login page is set by default.

Mode Global Configuration

Examples To set http://example.com/login.html as the login page, use the commands:

awplus# configure terminal

awplus(config)# auth-web-server login-url

http://example.com/login.html

To unset the login page URL, use the commands:

awplus# configure terminal

awplus(config)# no auth-web-server login-url

Commands

show running-config

Parameter Description

<URL>Set login page URL

613-50137-01 Rev A Command Reference for FS980M Series 1010

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER PAGE LOGO

auth-web-server page logo

Overview This command sets the type of logo that will be displayed on the web

authentication page.

Use the no variant of this command to set the logo type to auto.

Note that if you need to customize the login page extensively, you can instead

replace it with your own page. See “Customising the Login Page” in the AAA and

Port Authentication Feature Overview and Configuration Guide.

Syntax auth-web-server page logo {auto|default|hidden}

no auth-web-server page logo

Default Logo type is auto by default.

Mode Global Configuration

Examples To display the default logo with ignoring installed custom logo, use the

commands:

awplus# configure terminal

awplus(config)# auth-web-server page logo default

To set back to the default logo type auto, use the commands:

awplus# configure terminal

awplus(config)# no auth-web-server page logo

Validation

Commands

show auth-web-server page

Parameter Description

auto Display the custom logo if installed; otherwise display the

default logo

default Display the default logo

hidden Hide the logo

613-50137-01 Rev A Command Reference for FS980M Series 1011

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER PAGE SUB-TITLE

auth-web-server page sub-title

Overview This command sets the custom sub-title on the web authentication page.

Use the no variant of this command to reset the sub-title to its default.

Note that if you need to customize the login page extensively, you can instead

replace it with your own page. See “Customising the Login Page” in the AAA and

Port Authentication Feature Overview and Configuration Guide.

Syntax auth-web-server page sub-title {hidden|text <sub-title>}

no auth-web-server page sub-title

Default “Allied-Telesis” is displayed by default.

Mode Global Configuration

Examples To set the custom sub-title, use the commands:

awplus# configure terminal

awplus(config)# auth-web-server page sub-title text Web

Authentication

To hide the sub-title, use the commands:

awplus# configure terminal

awplus(config)# auth-web-server page sub-title hidden

To change back to the default title, use the commands:

awplus# configure terminal

awplus(config)# no auth-web-server page sub-title

Validation

Commands

show auth-web-server page

Parameter Description

hidden Hide the sub-title

<sub-title> Text string of the sub-title

613-50137-01 Rev A Command Reference for FS980M Series 1012

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER PAGE SUCCESS-MESSAGE

auth-web-server page success-message

Overview This command sets the success message on the web-authentication page.

Use the no variant of this command to remove the success message.

Note that if you need to customize the login page extensively, you can instead

replace it with your own page. See “Customising the Login Page” in the AAA and

Port Authentication Feature Overview and Configuration Guide.

Syntax auth-web-server page success-message text <success-message>

no auth-web-server page success-message

Default No success message is set by default.

Mode Global Configuration

Examples To set the success message on the web-authentication page, use the commands:

awplus# configure terminal

awplus(config)# auth-web-server page success-message text Your

success message

To unset the success message on the web-authentication page, use the

commands:

awplus# configure terminal

awplus(config)# no auth-web-server page success-message

Validation

Commands

show auth-web-server page

Parameter Description

<success-message> Text string of the success message

613-50137-01 Rev A Command Reference for FS980M Series 1013

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER PAGE TITLE

auth-web-server page title

Overview This command sets the custom title on the web authentication page.

Use the no variant of this command to remove the custom title.

Note that if you need to customize the login page extensively, you can instead

replace it with your own page. See “Customising the Login Page” in the AAA and

Port Authentication Feature Overview and Configuration Guide.

Syntax auth-web-server page title {hidden|text <title>}

no auth-web-server page title

Default “Web Access Authentication Gateway” is displayed by default.

Mode Global Configuration

Examples To set the custom title on the web authentication page, use the commands:

awplus# configure terminal

awplus(config)# auth-web-server page title text Login

To hide the title on the web authentication page, use the commands:

awplus# configure terminal

awplus(config)# auth-web-server page title hidden

To unset the custom title on the web authentication page, use the commands:

awplus# configure terminal

awplus(config)# no auth-web-server page title

Validation

Commands

show auth-web-server page

Parameter Description

hidden Hide the title

<title> Text string of the title

613-50137-01 Rev A Command Reference for FS980M Series 1014

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER PAGE WELCOME-MESSAGE

auth-web-server page welcome-message

Overview This command sets the welcome message on the web-authentication login page.

Use the no variant of this command to remove the welcome message.

Note that if you need to customize the login page extensively, you can instead

replace it with your own page. See “Customising the Login Page” in the AAA and

Port Authentication Feature Overview and Configuration Guide.

Syntax auth-web-server page welcome-message text <welcome-message>

no auth-web-server page welcome-message

Default No welcome message is set by default.

Mode Global Configuration

Examples To set the welcome message on the web-authentication page, use the commands:

awplus# configure terminal

awplus(config)# auth-web-server page welcome-message text Your

welcome message

To remove the welcome message on the web-authentication page, use the

commands:

awplus# configure terminal

awplus(config)# no auth-web-server page welcome-message

Validation

Commands

show auth-web-server page

Parameter Description

<welcome-message> Text string of the welcome message

613-50137-01 Rev A Command Reference for FS980M Series 1015

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER PING-POLL ENABLE

auth-web-server ping-poll enable

Overview This command enables the ping polling to the supplicant (client device) that is

authenticated by Web-Authentication.

The no variant of this command disables the ping polling to the supplicant that is

authenticated by Web-Authentication.

Syntax auth-web-server ping-poll enable

no auth-web-server ping-poll enable

Default The ping polling feature for Web-Authentication is disabled by default.

Mode Global Configuration

Examples To enable the ping polling feature for Web-Authentication, use the following

commands:

awplus# configure terminal

awplus(config)# auth-web-server ping-poll enable

To disable the ping polling feature for Web-Authentication, use the following

commands:

awplus# configure terminal

awplus(config)# no auth-web-server ping-poll enable

Validation

Commands

show auth

show auth-web-server

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 1016

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER PING-POLL FAILCOUNT

auth-web-server ping-poll failcount

Overview This command sets a fail count for the ping polling feature when used with

Web-Authentication. The failcount parameter specifies the number of

unanswered pings. A supplicant (client device) is logged off when the number of

unanswered pings are greater than the failcount set with this command.

Use the no variant of this command to resets the fail count for the ping polling

feature to the default (5 pings).

Syntax auth-web-server ping-poll failcount <1-100>

no auth-web-server ping-poll failcount

Default The default failcount for ping polling is 5 pings.

Mode Global Configuration

Examples To set the failcount of ping polling to 10 pings, use the following commands:

awplus# configure terminal

awplus(config)# auth-web-server ping-poll failcount 10

To set the failcount of ping polling to default, use the following commands:

awplus# configure terminal

awplus(config)# no auth-web-server ping-poll failcount

Validation

Commands

show auth

show auth-web-server

show running-config

Parameter Description

<1-100>Count.

613-50137-01 Rev A Command Reference for FS980M Series 1017

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER PING-POLL INTERVAL

auth-web-server ping-poll interval

Overview This command is used to change the ping poll interval. The interval specifies the

time period between pings when the supplicant (client device) is reachable.

Use the no variant of this command to reset to the default period for ping polling

(30 seconds).

Syntax auth-web-server ping-poll interval <1-65535>

no auth-web-server ping-poll interval

Default The interval for ping polling is 30 seconds by default.

Mode Global Configuration

Examples To set the interval of ping polling to 60 seconds, use the following commands:

awplus# configure terminal

awplus(config)# auth-web-server ping-poll interval 60

To set the interval of ping polling to the default (30 seconds), use the following

commands:

awplus# configure terminal

awplus(config)# no auth-web-server ping-poll interval

Validation

Commands

show auth

show auth-web-server

show running-config

Parameter Description

<1-65535>Seconds.

613-50137-01 Rev A Command Reference for FS980M Series 1018

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER PING-POLL REAUTH-TIMER-REFRESH

auth-web-server ping-poll

reauth-timer-refresh

Overview This command modifies the reauth-timer-refresh parameter for the

Web-Authentication feature. The reauth-timer-refresh parameter specifies

whether a re-authentication timer is reset and when the response from a

supplicant (a client device) is received.

Use the no variant of this command to reset the reauth-timer-refresh parameter

to the default setting (disabled).

Syntax auth-web-server ping-poll reauth-timer-refresh

no auth-web-server ping-poll reauth-timer-refresh

Default The reauth-timer-refresh parameter is disabled by default.

Mode Global Configuration

Examples To enable the reauth-timer-refresh timer, use the following commands:

awplus# configure terminal

awplus(config)# auth-web-server ping-poll reauth-timer-refresh

To disable the reauth-timer-refresh timer, use the following commands:

awplus# configure terminal

awplus(config)# no auth-web-server ping-poll

reauth-timer-refresh

Validation

Commands

show auth

show auth-web-server

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 1019

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER PING-POLL TIMEOUT

auth-web-server ping-poll timeout

Overview This command modifies the ping poll timeout parameter for the

Web-Authentication feature. The timeout parameter specifies the time in seconds

to wait for a response to a ping packet.

Use the no variant of this command to reset the timeout of ping polling to the

default (1 second).

Syntax auth-web-server ping-poll timeout <1-30>

no auth-web-server ping-poll timeout

Default The default timeout for ping polling is 1 second.

Mode Global Configuration

Examples To set the timeout of ping polling to 2 seconds, use the command:

awplus# configure terminal

awplus(config)# auth-web-server ping-poll timeout 2

To set the timeout of ping polling to the default (1 second), use the command:

awplus# configure terminal

awplus(config)# no auth-web-server ping-poll timeout

Validation

Commands

show auth

show auth-web-server

show running-config

Parameter Description

<1-30>Seconds.

613-50137-01 Rev A Command Reference for FS980M Series 1020

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER PORT

auth-web-server port

Overview This command sets the HTTP port number for the Web-Authentication server.

Use the no variant of this command to reset the HTTP port number to the default

(80).

Syntax auth-web-server port <port-number>

no auth-web-server port

Default The Web-Authentication server HTTP port number is set to 80 by default.

Mode Global Configuration

Examples To set the HTTP port number 8080 for the Web-Authentication server, use the

following commands:

awplus# configure terminal

awplus(config)# auth-web-server port 8080

To reset to the default HTTP port number 80 for the Web-Authentication server,

use the following commands:

awplus# configure terminal

awplus(config)# no auth-web-server port

Validation

Commands

show auth

show auth-web-server

show running-config

Parameter Description

<port-number>Set the local Web-Authentication server port within the TCP

port number range 1 to 65535.

613-50137-01 Rev A Command Reference for FS980M Series 1021

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER REDIRECT-DELAY-TIME

auth-web-server redirect-delay-time

Overview Use this command to set the delay time in seconds before redirecting the

supplicant to a specified URL when the supplicant is authorized.

Use the variant no to reset the delay time set previously.

Syntax auth-web-server redirect-delay-time <5-60>

no auth-web-server redirect-delay-time

Default The default redirect delay time is 5 seconds.

Mode Global Configuration

Examples To set the delay time to 60 seconds for the Web-Authentication server, use the

following commands:

awplus# configure terminal

awplus(config)# auth-web-server redirect-delay-time 60

To reset the delay time, use the following commands:

awplus# configure terminal

awplus(config)# no auth-web-server redirect-delay-time

Commands

auth-web-server blocking-mode

auth-web-server redirect-url

show auth-web-server

show running-config

Parameter Description

redirect-delay-time Set the delay time before jumping to a specified

URL after the supplicant is authorized.

<5-60>The time in seconds.

613-50137-01 Rev A Command Reference for FS980M Series 1022

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER REDIRECT-URL

auth-web-server redirect-url

Overview This command sets a URL for supplicant (client device) authentication. When a

supplicant is authorized it will be automatically redirected to the specified URL.

Note that if the http redirect feature is used then this command is ignored.

Use the no variant of this command to delete the URL string set previously.

Syntax auth-web-server redirect-url <url>

no auth-web-server redirect-url

Default The redirect URL for the Web-Authentication server feature is not set by default

(null).

Mode Global Configuration

Examples To enable and set redirect a URL string www.alliedtelesis.com for the Web-

Authentication server, use the following commands:

awplus# configure terminal

awplus(config)# auth-web-server redirect-url

http://www.alliedtelesis.com

To delete a redirect URL string, use the following commands:

awplus# configure terminal

awplus(config)# no auth-web-server redirect-url

Commands

auth-web-server redirect-delay-time

show auth

show auth-web-server

show running-config

Parameter Description

<url>URL (hostname or dotted IP notation).

613-50137-01 Rev A Command Reference for FS980M Series 1023

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER SESSION-KEEP

auth-web-server session-keep

Overview This command enables the session-keep feature to jump to the original URL after

being authorized by Web-Authentication.

Use the no variant of this command to disable the session keep feature.

Syntax auth-web-server session-keep

no auth-web-server session-keep

Default The session-keep feature is disabled by default.

Mode Global Configuration

Usage This function doesn't ensure to keep session information in all cases.

Authenticated supplicant may be redirected to unexpected page when

session-keep is enabled. This issue occurred by supplicant sending HTTP packets

automatically after authentication page is displayed and the URL is written.

Examples To enable the session-keep feature, use the following commands:

awplus# configure terminal

awplus(config)# auth-web-server session-keep

To disable the session-keep feature, use the following commands:

awplus# configure terminal

awplus(config)# no auth-web-server session-keep

Validation

Commands

show auth

show auth-web-server

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 1024

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER SSL

auth-web-server ssl

Overview This command enables HTTPS functionality for the Web-Authentication server

feature.

Use the no variant of this command to disable HTTPS functionality for the

Web-Authentication server.

Syntax auth-web-server ssl

no auth-web-server ssl

Default HTTPS functionality for the Web-Authentication server feature is disabled by

default.

Mode Global Configuration

Examples To enable HTTPS functionality for the Web-Authentication server feature, use the

following commands:

awplus# configure terminal

awplus(config)# auth-web-server ssl

To disable HTTPS functionality for the Web-Authentication server feature, use the

following commands:

awplus# configure terminal

awplus(config)# no auth-web-server ssl

Validation

Commands

show auth

show auth-web-server

show running-config

613-50137-01 Rev A Command Reference for FS980M Series 1025

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

AUTH-WEB-SERVER SSL INTERCEPT-PORT

auth-web-server ssl intercept-port

Overview Use this command to register HTTPS intercept port numbers when the HTTPS

server uses custom port number (not TCP port number 443).

Note that you need to use the auth-web-server intercept-port command to

Use the no variant of this command to delete registered port number.

Syntax auth-web-server ssl intercept-port <1-65535>

no auth-web-server ssl intercept-port <1-65535>

Default 443/TCP is registered by default.

Mode Global Configuration

Examples To register HTTPS port number 3128, use the commands:

awplus# configure terminal

awplus(config)# auth-web-server ssl intercept-port 3128

To delete HTTPS port number 3128, use the commands:

awplus# configure terminal

awplus(config)# no auth-web-server ssl intercept-port 3128

Validation

Commands

show auth-web-server

Commands

auth-web-server intercept-port

Parameter Description

<1-65535>TCP port number in the range from 1 through 65535

613-50137-01 Rev A Command Reference for FS980M Series 1026

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

COPY PROXY-AUTOCONFIG-FILE

copy proxy-autoconfig-file

Overview Use this command to download the proxy auto configuration (PAC) file to your

switch. The Web-Authentication supplicant can get the downloaded file from the

system web server.

Syntax copy <filename> proxy-autoconfig-file

Mode Privileged Exec

Example To download the PAC file to this device, use the command:

awplus# copy tftp://server/proxy.pac proxy-autoconfig-file

Commands

show proxy-autoconfig-file

erase proxy-autoconfig-file

Parameter Description

<filename>The URL of the PAC file.

613-50137-01 Rev A Command Reference for FS980M Series 1027

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

COPY WEB-AUTH-HTTPS-FILE

copy web-auth-https-file

Overview Use this command to download the SSL server certificate for web-based

authentication. The file must be in PEM (Privacy Enhanced Mail) format, and

contain the private key and the server certificate.

Syntax copy <filename> web-auth-https-file

Mode Privileged Exec

Example To download the server certificate file veriSign_cert.pem from the TFTP

server directory server, use the command:

awplus# copy tftp://server/veriSign_cert.pem

web-auth-https-file

Commands

auth-web-server ssl

erase web-auth-https-file

show auth-web-server

Parameter Description

<filename>The URL of the server certificate file.

613-50137-01 Rev A Command Reference for FS980M Series 1028

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

DESCRIPTION (AUTHENTICATION PROFILE)

description (Authentication Profile)

Overview Use this command to add a description to an authentication profile in

Authentication Profile mode.

Use the no variant of this command to remove the current description.

Syntax description <description>

Default No description configured by default.

Mode Authentication Profile

Example To add a description to the authentication profile ‘student’, use the following

commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# description student room setting

To remove a description from the authentication profile ‘student’, use the

following commands:

awplus# configure terminal

awplus(config)# auth profile student

awplus(config-auth-profile)# no description

Commands

auth profile (Global Configuration)

Parameter Description

<description>Text describing the selected authentication profile.

613-50137-01 Rev A Command Reference for FS980M Series 1029

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

ERASE PROXY-AUTOCONFIG-FILE

erase proxy-autoconfig-file

Overview Use this command to remove the proxy auto configuration file.

Syntax erase proxy-autoconfig-file

Mode Privileged Exec

Example To remove the proxy auto configuration file, use the command:

awplus# erase proxy-autoconfig-file

Commands

show proxy-autoconfig-file

copy proxy-autoconfig-file

613-50137-01 Rev A Command Reference for FS980M Series 1030

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

ERASE WEB-AUTH-HTTPS-FILE

erase web-auth-https-file

Overview Use this command to remove the SSL server certificate for web-based

authentication.

Syntax erase web-auth-https-file

Mode Privileged Exec

Example To remove the SSL server certificate file for web-based authentication use the

command:

awplus# erase web-auth-https-file

Commands

auth-web-server ssl

copy web-auth-https-file

show auth-web-server

613-50137-01 Rev A Command Reference for FS980M Series 1031

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

PLATFORM L3-VLAN-HASHING-ALGORITHM

platform l3-vlan-hashing-algorithm

Overview This command enables you to change the L3 VLAN hash-key-generating

algorithm.

The no variant of this command returns the hash-key algorithm to the default of

crc32l.

Syntax platform l3-vlan-hashing-algorithm

{crc16l|crc16u|crc32l|crc32u}

no platform l3-vlan-hashing-algorithm

Default The hash-key algorithm is crc32l by default.

Mode Global configuration

Usage Occasionally, when using the Multiple Dynamic VLAN feature, a supplicant cannot

be authenticated because a collision occurs within the VLAN L3 table. This can

happen when more than four different IP addresses produce the same hash-key.

When this situation occurs, collisions can sometimes be avoided by changing the

hashing algorithm from its default of crc32l. Several different algorithms may need

to be tried to rectify the problem.

You must restart the switch for this command to take effect.

Note that this command is intended for technical support staff, or advanced end

users.

Example To change the hash-key generating algorithm applying to the lower bits of CRC-16,

use the command:

awplus# configure terminal

awplus(config)# platform l3-vlan-hashing-algorithm crc16l

Commands

platform mac-vlan-hashing-algorithm

show platform

Parameter Description

crc16l The algorithm that will apply to the lower bits of CRC-16

crc16u The algorithm that will apply to the upper bits of CRC-16

crc32l The algorithm that will apply to the lower bits of CRC-32

crc32u The algorithm that will apply to the upper bits of CRC-32

613-50137-01 Rev A Command Reference for FS980M Series 1032

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

PLATFORM MAC-VLAN-HASHING-ALGORITHM

platform mac-vlan-hashing-algorithm

Overview This command enables you to change the MAC VLAN hash-key-generating

algorithm.

The no variant of this command returns the hash-key algorithm to the default of

crc32l

Syntax platform mac-vlan-hashing-algorithm

{crc16l|crc16u|crc32l|crc32u}

no platform mac-vlan-hashing-algorithm

Default The hash-key algorithm is crc32l by default.

Mode Global configuration

Usage Occasionally, when using the Multiple Dynamic VLAN feature, a supplicant cannot

be authenticated because a collision occurs within the VLAN MAC table. This can

happen when more than four different MAC addresses produce the same

hash-key.

When this situation occurs, collisions can sometimes be avoided by changing the

hashing algorithm from its default of crc32l. Several different algorithms may need

to be tried to rectify the problem.

You must restart the switch for this command to take effect.

Note that this command is intended for technical support staff, or advanced end

users.

Example To change the hash-key generating algorithm applying to the lower bits of CRC-16,

use the command:

awplus# configure terminal

awplus(config)# platform mac-vlan-hashing-algorithm crc16l

Commands

platform l3-vlan-hashing-algorithm

show platform

Parameter Description

crc16l The algorithm that will apply to the lower bits of CRC-16

crc16u The algorithm that will apply to the upper bits of CRC-16

crc32l The algorithm that will apply to the lower bits of CRC-32

crc32u The algorithm that will apply to the upper bits of CRC-32

613-50137-01 Rev A Command Reference for FS980M Series 1033

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

SHOW AUTH

show auth

Overview This command shows the configuration state of authentication.

Syntax show auth [all]

Mode Privileged Exec

Example To display all authentication information, enter the command:

awplus# show auth all

Output Figure 29-1: Example output from the show auth command

Parameter Description

all Display all authentication information for each authenticated

interface. This can be a static channel (or static aggregator), or a

dynamic (or LACP) channel group, or a switch port.

awplus# show auth all

802.1X Port-Based Authentication Enabled

MAC-based Port Authentication Disabled

WEB-based Port Authentication Enabled

RADIUS server address (auth): 150.87.17.192:1812

Last radius message id: 4

Authentication Info for interface port1.0.1 portEnabled: true - portControl: Auto

portStatus: Authorized

reAuthenticate: disabled

reAuthPeriod: 3600

PAE: quietPeriod: 60 - maxReauthReq: 2 - txPeriod: 30

BE: suppTimeout: 30 - serverTimeout: 30

CD: adminControlledDirections: in

KT: keyTxEnabled: false

critical: disabled

guestVlan: disabled

authFailVlan: disabled

dynamicVlanCreation: disabled

hostMode: single-host

dot1x: enabled

protocolVersion: 1

authMac: disabled

authWeb: enabled

method: PAP

maxAuthFail: 3

packetForwarding:

10.0.0.1 80/tcp

dns

dhcp

613-50137-01 Rev A Command Reference for FS980M Series 1034

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

SHOW AUTH

Commands

show dot1x

twoStepAuthentication:

configured: enabled

actual: enabled

supplicantMac: none

Supplicant name: oha

Supplicant address: 000d.6013.5398

authenticationMethod: WEB-based Authentication

Two-Step Authentication:

firstAuthentication: Pass - Method: dot1x

secondAuthentication: Pass - Method: web

portStatus: Authorized - currentId: 3

abort:F fail:F start:F timeout:F success:T

PAE: state: Authenticated - portMode: Auto

PAE: reAuthCount: 0 - rxRespId: 0

PAE: quietPeriod: 60 - maxReauthReq: 2

BE: state: Idle - reqCount: 0 - idFromServer: 2

CD: adminControlledDirections: in - operControlledDirections: in

CD: bridgeDetected: false

KR: rxKey: false

KT: keyAvailable: false - keyTxEnabled: false

613-50137-01 Rev A Command Reference for FS980M Series 1035

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

SHOW AUTH DIAGNOSTICS

show auth diagnostics

Overview This command shows authentication diagnostics, optionally for the specified

interface, which may be a static channel (or static aggregator) or a dynamic (or

LACP) channel group or a switch port.

If no interface is specified then authentication diagnostics are shown for all

interfaces.

Syntax show auth diagnostics [interface <interface-list>]

Mode Privileged Exec

Example To display authentication diagnostics for port1.0.6, enter the command:

awplus# show auth diagnostics interface port1.0.6

Parameter Description

interface Specify ports to show.

<interface-list> The interfaces or ports to configure. An interface-list can be:

•an interface (e.g. vlan2), a switch port (e.g. port1.0.6),

a static channel group (e.g. sa2) or a dynamic (LACP)

channel group (e.g. po2)

• a continuous range of interfaces, ports, static channel

groups or dynamic (LACP) channel groups separated by a

hyphen; e.g. vlan2-8, or port1.0.1-1.0.4, or sa1-2,

or po1-2

• a comma-separated list of the above; e.g.

port1.0.1,port1.0.4-1.0.6. Do not mix interface

types in a list

The specified interfaces must exist.

613-50137-01 Rev A Command Reference for FS980M Series 1036

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

SHOW AUTH DIAGNOSTICS

Output Figure 29-2: Example output from the show auth diagnostics command

Commands

show dot1x interface

Authentication Diagnostics

for interface port1.0.6

Supplicant address: 00d0.59ab.7037

authEnterConnecting: 2

authEaplogoffWhileConnecting: 1

authEnterAuthenticating: 2

authSuccessWhileAuthenticating: 1

authTimeoutWhileAuthenticating: 1

authFailWhileAuthenticating: 0

authEapstartWhileAuthenticating: 0

authEaplogoggWhileAuthenticating: 0

authReauthsWhileAuthenticated: 0

authEapstartWhileAuthenticated: 0

authEaplogoffWhileAuthenticated: 0

BackendResponses: 2

BackendAccessChallenges: 1

BackendOtherrequestToSupplicant: 3

BackendAuthSuccess: 1

613-50137-01 Rev A Command Reference for FS980M Series 1037

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

SHOW AUTH INTERFACE

show auth interface

Overview This command shows the status of port authentication on the specified interface,

which may be a static channel (or static aggregator) or a dynamic (or LACP)

channel group or a switch port.

Use the optional diagnostics parameter to show authentication diagnostics for

the specified interface. Use the optional sessionstatistics parameter to show

authentication session statistics for the specified interface. Use the optional

statistics parameter to show authentication diagnostics for the specified

interface. Use the optional supplicant (client device) parameter to show the

supplicant state for the specified interface.

Syntax show auth interface <interface-list>

[diagnostics|sessionstatistics|statistics|supplicant [brief]]

Mode Privileged Exec

Example To display the Web based authentication status for port1.0.6, enter the

command:

awplus# show auth interface port1.0.6

If web-based authentication is not configured, the output will be

Parameter Description

<interface-list> The interfaces or ports to configure. An interface-list can be:

•an interface (e.g. vlan2), a switch port (e.g. port1.0.6),

a static channel group (e.g. sa2) or a dynamic (LACP)

channel group (e.g. po2)

• a continuous range of interfaces, ports, static channel

groups or dynamic (LACP) channel groups separated by a

hyphen; e.g. vlan2-8, or port1.0.1-1.0.4, or

sa1-2, or po1-2

• a comma-separated list of the above; e.g.

port1.0.1,port1.0.4-1.0.6. Do not mix interface

types in a list

The specified interfaces must exist.

diagnostics Diagnostics.

sessionstatistics Session statistics.

statistics Statistics.

supplicant Supplicant (client device).

brief Brief summary of supplicant state.

% Port-Control not configured on port1.0.6

613-50137-01 Rev A Command Reference for FS980M Series 1038

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

SHOW AUTH INTERFACE

To display the Web based authentication status for port1.0.1, enter the

command:

awplus# show auth interface port1.0.1

To display Web-Authentication diagnostics for port1.0.6, enter the command:

awplus# show auth interface port1.0.6 diagnostics

awplus# show auth interface port1.0.1

Authentication Info for interface port1.0.1

portEnabled: true - portControl: Auto

portStatus: Authorized

reAuthenticate: disabled

reAuthPeriod: 3600

PAE: quietPeriod: 60 - maxReauthReq: 2 - txPeriod: 30

BE: suppTimeout: 30 - serverTimeout: 30

CD: adminControlledDirections: in

KT: keyTxEnabled: false

critical: disabled

guestVlan: disabled

guestVlanForwarding:

none

authFailVlan: disabled

dynamicVlanCreation: disabled

hostMode: single-host

dot1x: enabled

protocolVersion: 1

authMac: disabled

authWeb: enabled

method: PAP

maxAuthFail: 3

packetForwarding:

10.0.0.1 80/tcp

dns

dhcp

twoStepAuthentication:

configured: enabled

actual: enabled

supplicantMac: none

613-50137-01 Rev A Command Reference for FS980M Series 1039

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

SHOW AUTH INTERFACE

To display Web-Authentication session statistics for port1.0.6, enter the

command:

awplus# show auth interface port1.0.6 sessionstatistics

To display Web-Authentication statistics for port1.0.6, enter the command:

awplus# show auth statistics interface port1.0.6

To display the Web-Authenticated supplicant on interface port1.0.6, enter the

command:

awplus# show auth interface port1.0.6 supplicant

Commands

show auth diagnostics

show dot1x sessionstatistics

show dot1x statistics interface

show dot1x supplicant interface

Authentication Diagnostics for interface port1.0.6 



Supplicant address: 00d0.59ab.7037

authEnterConnecting: 2

authEaplogoffWhileConnecting: 1

authEnterAuthenticating: 2

authSuccessWhileAuthenticating: 1

authTimeoutWhileAuthenticating: 1

authFailWhileAuthenticating: 0

authEapstartWhileAuthenticating: 0

authEaplogoggWhileAuthenticating: 0

authReauthsWhileAuthenticated: 0

authEapstartWhileAuthenticated: 0

authEaplogoffWhileAuthenticated: 0

BackendResponses: 2

BackendAccessChallenges: 1

BackendOtherrequestToSupplicant: 3

BackendAuthSuccess: 1

Authentication session statistics for interface port1.0.6

session user name: manager

session authentication method: Remote server

session time: 19440 secs

session terminat cause: Not terminated yet

613-50137-01 Rev A Command Reference for FS980M Series 1040

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

SHOW AUTH SESSIONSTATISTICS

show auth sessionstatistics

Overview This command shows authentication session statistics for the specified interface,

which may be a static channel (or static aggregator) or a dynamic (or LACP)

channel group or a switch port.

Syntax show auth sessionstatistics [interface <interface-list>]

Mode Privileged Exec

Example To display authentication statistics for port1.0.6, enter the command:

awplus# show auth sessionstatistics interface port1.0.6

Output Figure 29-3: Example output from the show auth sessionstatistics command

Parameter Description

interface Specify ports to show.

<interface-list> The interfaces or ports to configure. An interface-list can be:

•an interface (e.g. vlan2), a switch port (e.g.

port1.0.6), a static channel group (e.g. sa2) or a

dynamic (LACP) channel group (e.g. po2)

• a continuous range of interfaces, ports, static channel

groups or dynamic (LACP) channel groups separated by

a hyphen; e.g. vlan2-8, or port1.0.1-1.0.4, or

sa1-2, or po1-2

• a comma-separated list of the above; e.g.

port1.0.1,port1.0.4-1.0.6. Do not mix

interface types in a list

The specified interfaces must exist.

Authentication session

statistics for interface port1.0.6

session user name: manager

session authentication method: Remote server

session time: 19440 secs

session terminat cause: Not terminated yet

613-50137-01 Rev A Command Reference for FS980M Series 1041

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

SHOW AUTH STATISTICS INTERFACE

show auth statistics interface

Overview This command shows the authentication statistics for the specified interface,

which may be a static channel (or static aggregator) or a dynamic (or LACP)

channel group or a switch port.

Syntax show auth statistics interface <interface-list>

Mode Privileged Exec

Example To display Web-Authentication statistics for port1.0.4, enter the command:

awplus# show auth statistics interface port1.0.4

Commands

show dot1x interface

Parameter Description

<interface-list> The interfaces or ports to configure. An interface-list can be:

• an interface (e.g. vlan2), a switch port (e.g. port1.0.6),

a static channel group (e.g. sa2) or a dynamic (LACP)

channel group (e.g. po2)

• a continuous range of interfaces, ports, static channel

groups or dynamic (LACP) channel groups separated by a

hyphen; e.g. vlan2-8, or port1.0.1-1.0.4, or sa1-2,

or po1-2

• a comma-separated list of the above; e.g.

port1.0.1,port1.0.4-1.0.6. Do not mix interface

types in a list

The specified interfaces must exist.

613-50137-01 Rev A Command Reference for FS980M Series 1042

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

SHOW AUTH SUPPLICANT

show auth supplicant

Overview This command shows the supplicant (client device) state when authentication is

configured for the switch. Use the optional brief parameter to show a summary of

the supplicant state.

Syntax show auth supplicant [<macadd>] [brief]

Mode Privileged Exec

Examples To display a summary of authenticated supplicant information on the device, enter

the command:

awplus# show auth supplicant brief

To display authenticated supplicant information on the device, enter the

command:

awplus# show auth supplicant

To display authenticated supplicant information for device with MAC address

0000.5E00.5301, enter the command:

awplus# show auth supplicant 0000.5E00.5301

Output Figure 29-4: Example output from show auth supplicant brief

Parameter Description

<macadd>Mac (hardware) address of the supplicant.

Entry format is HHHH.HHHH.HHHH (hexadecimal).

brief Brief summary of the supplicant state.

awplus#show auth supplicant brief

Interface port2.0.3

authenticationMethod: dot1x/mac/web

Two-Step Authentication

firstMethod: mac

secondMethod: dot1x/web

totalSupplicantNum: 1

authorizedSupplicantNum: 1

macBasedAuthenticationSupplicantNum: 0

dot1xAuthenticationSupplicantNum: 0

webBasedAuthenticationSupplicantNum: 1

otherAuthenticationSupplicantNum: 0RADIUS Group Configuration



Interface VID Mode MAC Address Status IP Address Username

=========== ==== ==== ============== ================= =============== ========

port2.0.3 1 W 001c.233e.e15a Authenticated 192.168.1.181 test

613-50137-01 Rev A Command Reference for FS980M Series 1043

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

SHOW AUTH SUPPLICANT

Figure 29-5: Example output from show auth supplicant

Figure 29-6: Example output from show auth supplicant 0000.5E00.5301

awplus#show auth supplicant

Interface port2.0.3

authenticationMethod: dot1x/mac/web

Two-Step Authentication

firstMethod: mac

secondMethod: dot1x/web

totalSupplicantNum: 1

authorizedSupplicantNum: 1

macBasedAuthenticationSupplicantNum: 0

dot1xAuthenticationSupplicantNum: 0

webBasedAuthenticationSupplicantNum: 1

otherAuthenticationSupplicantNum: 0



Supplicant name: test

Supplicant address: 0000.5E00.5301

authenticationMethod: WEB-based Authentication

Two-Step Authentication:

firstAuthentication: Pass - Method: mac

secondAuthentication: Pass - Method: web

portStatus: Authorized - currentId: 1

abort:F fail:F start:F timeout:F success:T

PAE: state: Authenticated - portMode: Auto

PAE: reAuthCount: 0 - rxRespId: 0

PAE: quietPeriod: 60 - maxReauthReq: 2

BE: state: Idle - reqCount: 0 - idFromServer: 0

CD: adminControlledDirections: in - operControlledDirections: in

CD: bridgeDetected: false

KR: rxKey: false

KT: keyAvailable: false - keyTxEnabled: false

RADIUS server group (auth): radius

RADIUS server (auth): 192.168.1.40

awplus#show auth supplicant 0000.5E00.5301

Interface port2.0.3

Supplicant name: test

Supplicant address: 0000.5E00.5301

authenticationMethod: WEB-based Authentication

Two-Step Authentication:

firstAuthentication: Pass - Method: mac

secondAuthentication: Pass - Method: web

portStatus: Authorized - currentId: 1

abort:F fail:F start:F timeout:F success:T

PAE: state: Authenticated - portMode: Auto

PAE: reAuthCount: 0 - rxRespId: 0

PAE: quietPeriod: 60 - maxReauthReq: 2

BE: state: Idle - reqCount: 0 - idFromServer: 0

CD: adminControlledDirections: in - operControlledDirections: in

CD: bridgeDetected: false

KR: rxKey: false

KT: keyAvailable: false - keyTxEnabled: false

RADIUS server group (auth): radius

RADIUS server (auth): 192.168.1.40

613-50137-01 Rev A Command Reference for FS980M Series 1044

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

SHOW AUTH SUPPLICANT

Commands

aaa accounting auth-mac

aaa accounting auth-web

aaa accounting dot1x

aaa authentication auth-mac

aaa authentication auth-web

aaa authentication dot1x

613-50137-01 Rev A Command Reference for FS980M Series 1045

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

SHOW AUTH SUPPLICANT INTERFACE

show auth supplicant interface

Overview This command shows the supplicant (client device) state for the authentication

mode set for the interface, which may be a static channel (or static aggregator) or

a dynamic (or LACP) channel group or a switch port. Use the optional brief

parameter to show a summary of the supplicant state.

Syntax show auth-web supplicant interface <interface-list> [brief]

Mode Privileged Exec

Examples To display the authenticated supplicant on the interface port1.0.3, enter the

command:

awplus# show auth supplicant interface port1.0.3

To display brief summary output for the authenticated supplicant, enter the

command:

awplus# show auth supplicant brief

Parameter Description

<interface-list> The interfaces or ports to configure. An interface-list can be:

•an interface (e.g. vlan2), a switch port (e.g. port1.0.6),

a static channel group (e.g. sa2) or a dynamic (LACP)

channel group (e.g. po2)

• a continuous range of interfaces, ports, static channel

groups or dynamic (LACP) channel groups separated by a

hyphen; e.g. vlan2-8, or port1.0.1-1.0.4, or sa1-2,

or po1-2

• a comma-separated list of the above; e.g.

port1.0.1,port1.0.4-1.0.6. Do not mix interface

types in a list

The specified interfaces must exist.

brief Brief summary of the supplicant state.

613-50137-01 Rev A Command Reference for FS980M Series 1046

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

SHOW AUTH TWO-STEP SUPPLICANT BRIEF

show auth two-step supplicant brief

Overview This command displays the supplicant state of the two-step authentication feature

on the interface.

Syntax show auth two-step supplicant [interface <ifrange>] brief

Mode Privileged Exec

Usage Do not mix interface types in a list. The specified interfaces must exist.

Example To display the supplicant state of the two-step authentication feature, enter the

command:

awplus# show two-step supplicant interface port1.0.6 brief

Output Figure 29-7: Example output from show auth two-step supplicant brief

Commands

auth two-step enable

Parameter Description

interface The interface selected for display.

<ifrange>The interface types which can be specified as <ifrange>

• Switch port (e.g. port1.0.6)

• Static channel group (e.g. sa3)

• Dynamic (LACP) channel group (e.g. po4)

interface port1.0.6



authenticationMethod: dot1x/mac



Two-Step Authentication:

firstMethod:mac

secondMethod:dot1x

totalSupplicantNum: 1

authorizedSupplicantNum: 1

macBasedAuthenticationSupplicantNum: 0

dot1xAuthenticationSupplicantNum: 1

webBasedAuthenticationSupplicantNum: 0

otherAuthenticationSupplicantNum: 0



Interface VID Mode MAC Address Status FirstStep SecondStep

========== === ==== =========== ====== ========= ==========

port1.0.6 1 D 000b..db67.00f7 Authenticated Pass Pass

613-50137-01 Rev A Command Reference for FS980M Series 1047

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

SHOW AUTH-WEB-SERVER

show auth-web-server

Overview This command shows the Web-Authentication server configuration and status on

the switch.

Syntax show auth-web-server

Mode Privileged Exec

Example To display Web-Authentication server configuration and status, enter the

command:

awplus# show auth-web-server

Output Figure 29-8: Example output from the show auth-web-server command

Commands

auth-web-server ipaddress

auth-web-server port

auth-web-server redirect-delay-time

auth-web-server redirect-url

auth-web-server session-keep

auth-web-server ssl

Web authentication server

Server status: enabled

Server mode: none

Server address: 192.168.1.1/24

DHCP server enabled

DHCP lease time: 20

DHCP WPAD Option URL: http://192.168.1.1/proxy.pac

HTTP Port No: 80

Security: disabled

Certification: default

SSL Port No: 443

Redirect URL: --

Redirect Delay Time: 5

HTTP Redirect: enabled

Session keep: disabled

PingPolling: disabled

PingInterval: 30

Timeout: 1

FailCount: 5

ReauthTimerReFresh: disabled

613-50137-01 Rev A Command Reference for FS980M Series 1048

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

SHOW AUTH-WEB-SERVER PAGE

show auth-web-server page

Overview This command displays the web-authentication page configuration and status.

Syntax show auth-web-server page

Mode Privileged Exec

Examples To show the web-authentication page information, use the command:

awplus# show auth-web-server page

Figure 29-9: Example output from the show auth-web-server page command

Commands

auth-web forward

auth-web-server page logo

auth-web-server page sub-title

auth-web-server page success-message

auth-web-server page title

auth-web-server page welcome-message

awplus#show auth-web-server page

Web authentication page

Logo: auto

Title: default

Sub-Title: Web Authentication

Welcome message: Your welcome message 

Success message: Your success message

613-50137-01 Rev A Command Reference for FS980M Series 1049

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AUTHENTICATION COMMANDS

SHOW PROXY-AUTOCONFIG-FILE

show proxy-autoconfig-file

Overview This command displays the contents of the proxy auto configuration (PAC) file.

Syntax show proxy-autoconfig-file

Mode Privileged Exec

Example To display the contents of the proxy auto configuration (PAC) file, enter the

command:

awplus# show auth proxy-autoconfig-file

Output Figure 29-10: Example output from the show proxy-autoconfig-file

Commands

copy proxy-autoconfig-file

erase proxy-autoconfig-file

function FindProxyForURL(url,host)

{

if (isPlainHostName(host) ||

isInNet(host, “192.168.1.0”,”255.255.255.0”)) {

return “DIRECT”;

}

else {

return “PROXY 192.168.110.1:8080”;

}

613-50137-01 Rev A Command Reference for FS980M Series 1050

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA Commands

Introduction

Overview This chapter provides an alphabetical reference for AAA commands for

Authentication, Authorization and Accounting. For more information, see the AAA

Feature Overview and Configuration Guide.

Command List •“aaa accounting auth-mac” on page 1052

•“aaa accounting auth-web” on page 1054

•“aaa accounting commands” on page 1056

•“aaa accounting dot1x” on page 1058

•“aaa accounting login” on page 1060

•“aaa accounting update” on page 1063

•“aaa authentication auth-mac” on page 1065

•“aaa authentication auth-web” on page 1067

•“aaa authentication dot1x” on page 1068

•“aaa authentication enable default group tacacs+” on page 1069

•“aaa authentication enable default local” on page 1071

•“aaa authentication login” on page 1072

•“aaa authorization commands” on page 1074

•“aaa authorization config-commands” on page 1076

•“aaa group server” on page 1077

•“aaa local authentication attempts lockout-time” on page 1079

•“aaa local authentication attempts max-fail” on page 1080

•“aaa login fail-delay” on page 1081

•“accounting login” on page 1082

613-50137-01 Rev A Command Reference for FS980M Series 1051

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

•“authorization commands” on page 1083

•“clear aaa local user lockout” on page 1085

•“debug aaa” on page 1086

•“login authentication” on page 1087

•“proxy-port” on page 1088

•“radius-secure-proxy aaa” on page 1089

•“server (radsecproxy-aaa)” on page 1090

•“server mutual-authentication” on page 1092

•“server name-check” on page 1093

•“server trustpoint” on page 1094

•“show aaa local user locked” on page 1096

•“show debugging aaa” on page 1097

•“undebug aaa” on page 1098

613-50137-01 Rev A Command Reference for FS980M Series 1052

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA ACCOUNTING AUTH-MAC

aaa accounting auth-mac

Overview This command configures the default accounting method list for MAC-based

authentication. The default accounting method list specifies what type of

accounting messages are sent and which RADIUS servers the accounting

messages are sent to. The default accounting method list is automatically applied

to interfaces with MAC-based authentication enabled.

Use the no variant of this command to disable AAA accounting for MAC-based

authentication globally.

Syntax aaa accounting auth-mac default {start-stop|stop-only|none}

group {<group-name>|radius}

no aaa accounting auth-mac default

Default RADIUS accounting for MAC-based Authentication is disabled by default

Mode Global Configuration

Usage There are two ways to define servers where RADIUS accounting messages are sent:

•group radius: use all RADIUS servers configured by radius-server host

command

•group <group-name>: use the specified RADIUS server group configured

with the aaa group server command

The accounting event to send to the RADIUS server is configured with the

following options:

•start-stop: sends a start accounting message at the beginning of a session

and a stop accounting message at the end of the session.

•stop-only: sends a stop accounting message at the end of a session.

•none: disables accounting.

Parameter Description

default Configure the default accounting method list

start-stop Sends a start accounting message at the beginning of the session

and a stop accounting message at the end of the session.

stop-only Only sends a stop accounting message at the end of the session.

none No accounting record sent.

group Use a server group

<group-name>Server group name.

radius Use all RADIUS servers.

613-50137-01 Rev A Command Reference for FS980M Series 1053

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA ACCOUNTING AUTH-MAC

Examples To enable the default RADIUS accounting for MAC-based authentication, and use

all available RADIUS servers, use the commands:

awplus# configure terminal

awplus(config)# aaa accounting auth-mac default start-stop

group radius

To disable RADIUS accounting for MAC-based Authentication, use the commands:

awplus# configure terminal

awplus(config)# no aaa accounting auth-mac default

Commands

aaa authentication auth-mac

aaa group server

auth-mac enable

radius-server host

613-50137-01 Rev A Command Reference for FS980M Series 1054

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA ACCOUNTING AUTH-WEB

aaa accounting auth-web

Overview This command configures the default accounting method list for Web-based

authentication. The default accounting method list specifies what type of

accounting messages are sent and which RADIUS servers the accounting

messages are sent to. The default accounting method list is automatically applied

to interfaces with Web-based authentication enabled.

Use the no variant of this command to disable AAA accounting for Web-based

authentication globally.

Syntax aaa accounting auth-web default {start-stop|stop-only|none}

group {<group-name>|radius}

no aaa accounting auth-web default

Default RADIUS accounting for Web-based authentication is disabled by default.

Mode Global Configuration

Usage There are two ways to define servers where RADIUS accounting messages are sent:

•group radius: use all RADIUS servers configured by radius-server host

command

•group <group-name>: use the specified RADIUS server group configured

with the aaa group server command

Configure the accounting event to be sent to the RADIUS server with the following

options:

•start-stop: sends a start accounting message at the beginning of a session

and a stop accounting message at the end of the session.

•stop-only: sends a stop accounting message at the end of a session.

•none: disables accounting.

Parameter Description

default Configure the default accounting method list

start-stop Sends a start accounting message at the beginning of the session

and a stop accounting message at the end of the session.

stop-only Only sends a stop accounting message at the end of the session.

none No accounting record sent.

group Use a server group

<group-name>Server group name.

radius Use all RADIUS servers.

613-50137-01 Rev A Command Reference for FS980M Series 1055

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA ACCOUNTING AUTH-WEB

Examples To enable the default RADIUS accounting method for Web-based authentication,

and use all available RADIUS servers, use the commands:

awplus# configure terminal

awplus(config)# aaa accounting auth-web default start-stop

group radius

To disable the default RADIUS accounting method for Web-based authentication,

use the commands:

awplus# configure terminal

awplus(config)# no aaa accounting auth-web default

Commands

aaa authentication auth-web

aaa group server

auth-web enable

radius-server host

613-50137-01 Rev A Command Reference for FS980M Series 1056

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA ACCOUNTING COMMANDS

aaa accounting commands

Overview This command configures and enables TACACS+ accounting on commands

entered at a specified privilege level. Once enabled for a privilege level, accounting

messages for commands entered at that privilege level will be sent to a TACACS+

server.

In order to account for all commands entered on a device, configure command

accounting for each privilege level separately.

The command accounting message includes, the command as entered, the date

and time the command finished executing, and the user-name of the user who

executed the command.

Use the no variant of this command to disable command accounting for a

specified privilege level.

Syntax aaa accounting commands <1-15> default stop-only group tacacs+

no aaa accounting commands <1-15> default

Default TACACS+ command accounting is disabled by default.

Mode Global Configuration

Usage This command only supports a default method list, this means that it is applied to

every console and VTY line.

The stop-only parameter indicates that the command accounting messages are

sent to the TACACS+ server when the commands have stopped executing.

The group tacacs+ parameters signifies that the command accounting messages

are sent to the TACACS+ servers configured by the tacacs-server host command.

Note that up to four TACACS+ servers can be configured for accounting. The

servers are checked for reachability in the order they are configured with only the

first reachable server being used. If no server is found, the accounting message is

dropped.

Parameter Description

<1-15>The privilege level being configured, in the range 1 to 15.

default Use the default method list, this means the command is applied

globally to all user exec sessions.

stop-only Send accounting message when the commands have stopped

executing.

group Specify the server group where accounting messages are sent.

Only the tacacs+ group is available for this command.

tacacs+ Use all TACACS+ servers configured by the tacacs-server host

command.

613-50137-01 Rev A Command Reference for FS980M Series 1057

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA ACCOUNTING COMMANDS

Command accounting cannot coexist with triggers. An error message is displayed

if you attempt to enable command accounting while a trigger is configured.

Likewise, an error message is displayed if you attempt to configure a trigger while

command accounting is configured.

Examples To configure command accounting for privilege levels 1, 7, and 15, use the

following commands:

awplus# configure terminal

awplus(config)# aaa accounting commands 1 default stop-only

group tacacs+

awplus(config)# aaa accounting commands 7 default stop-only

group tacacs+

awplus(config)# aaa accounting commands 15 default stop-only

group tacacs+

To disable command accounting for privilege levels 1, 7, and 15, use the following

commands:

awplus# configure terminal

awplus(config)# no aaa accounting commands 1 default

awplus(config)# no aaa accounting commands 7 default

awplus(config)# no aaa accounting commands 15 default

Commands

aaa authentication login

aaa accounting login

accounting login

tacacs-server host

613-50137-01 Rev A Command Reference for FS980M Series 1058

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA ACCOUNTING DOT1X

aaa accounting dot1x

Overview This command configures the default accounting method list for IEEE

802.1X-based authentication. The default accounting method list specifies what

type of accounting messages are sent and which RADIUS servers the accounting

messages are sent to. The default accounting method list is automatically applied

to interfaces with IEEE 802.1X-based authentication enabled.

Use the no variant of this command to disable AAA accounting for 802.1X-based

authentication globally.

Syntax aaa accounting dot1x default {start-stop|stop-only|none} group

{<group-name>|radius}

no aaa accounting dot1x default

Default RADIUS accounting for 802.1X-based authentication is disabled by default (there

is no default server set by default).

Mode Global Configuration

Usage There are two ways to define servers where RADIUS accounting messages will be

sent:

•group radius: use all RADIUS servers configured by radius-server host

command.

•group <group-name>: use the specified RADIUS server group configured

with the aaa group server command.

The accounting event to send to the RADIUS server is configured by the following

options:

•start-stop: sends a start accounting message at the beginning of a session

and a stop accounting message at the end of the session.

•stop-only: sends a stop accounting message at the end of a session.

•none: disables accounting.

Parameter Description

default Configure the default accounting method list

start-stop Sends a start accounting message at the beginning of the session

and a stop accounting message at the end of the session.

stop-only Only sends a stop accounting message at the end of the session.

none No accounting record sent.

group Use a server group

<group-name>Server group name.

radius Use all RADIUS servers.

613-50137-01 Rev A Command Reference for FS980M Series 1059

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA ACCOUNTING DOT1X

Examples To enable RADIUS accounting for 802.1X-based authentication, and use all

available RADIUS Servers, use the commands:

awplus# configure terminal

awplus(config)# aaa accounting dot1x default start-stop group

radius

To disable RADIUS accounting for 802.1X-based authentication, use the

commands:

awplus# configure terminal

awplus(config)# no aaa accounting dot1x default

Commands

aaa accounting update

aaa authentication dot1x

aaa group server

dot1x port-control

radius-server host

613-50137-01 Rev A Command Reference for FS980M Series 1060

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA ACCOUNTING LOGIN

aaa accounting login

Overview This command configures RADIUS and TACACS+ accounting for login shell

sessions. The specified method list name can be used by the accounting login

command in the Line Configuration mode. If the default parameter is specified,

then this creates a default method list that is applied to every console and VTY line,

unless another accounting method list is applied on that line.

Note that unlimited RADIUS servers and up to four TACACS+ servers can be

configured and consulted for accounting. The first server configured is regarded as

the primary server and if the primary server fails then the backup servers are

consulted in turn. A backup server is consulted if the primary server fails, i.e. is

unreachable.

Use the no variant of this command to remove an accounting method list for login

shell sessions configured by an aaa accounting login command. If the method list

being deleted is already applied to a console or VTY line, accounting on that line

will be disabled. If the default method list name is removed by this command, it will

disable accounting on every line that has the default accounting configuration.

Syntax aaa accounting login

{default|<list-name>}{start-stop|stop-only|none} {group

{radius|tacacs+|<group-name>}}

no aaa accounting login {default|<list-name>}

Default Accounting for login shell sessions is disabled by default.

Mode Global Configuration

Parameter Description

default Default accounting method list.

<list-name>Named accounting method list.

start-stop Start and stop records to be sent.

stop-only Stop records to be sent.

none No accounting record to be sent.

group Specify the servers or server group where accounting packets are

sent.

radius Use all RADIUS servers configured by the radius-server host

command.

tacacs+ Use all TACACS+ servers configured by the tacacs-server host

command.

<group-name> Use the specified RADIUS server group, as configured by the aaa

group server command.

613-50137-01 Rev A Command Reference for FS980M Series 1061

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA ACCOUNTING LOGIN

Usage This command enables you to define a named accounting method list. The items

that you define in the accounting options are:

• the types of accounting packets that will be sent

• the set of servers to which the accounting packets will be sent

You can define a default method list with the name default and any number of

other named method lists. The name of any method list that you define can then

be used as the <list-name> parameter in the accounting login command.

If the method list name already exists, the command will replace the existing

configuration with the new one.

There are two ways to define servers where RADIUS accounting messages are sent:

•group radius : use all RADIUS servers configured by radius-server host

command

•group <group-name> : use the specified RADIUS server group configured

with the aaa group server command

There is one way to define servers where TACACS+ accounting messages are sent:

•group tacacs+ : use all TACACS+ servers configured by tacacs-server host

command

The accounting event to send to the RADIUS or TACACS+ server is configured with

the following options:

•start-stop : sends a start accounting message at the beginning of a session

and a stop accounting message at the end of the session.

•stop-only : sends a stop accounting message at the end of a session.

•none : disables accounting.

Examples To configure RADIUS accounting for login shell sessions, use the following

commands:

awplus# configure terminal

awplus(config)# aaa accounting login default start-stop group

radius

To configure TACACS+ accounting for login shell sessions, use the following

commands:

awplus# configure terminal

awplus(config)# aaa accounting login default start-stop group

tacacs+

To reset the configuration of the default accounting list, use the following

commands:

awplus# configure terminal

awplus(config)# no aaa accounting login default

613-50137-01 Rev A Command Reference for FS980M Series 1062

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA ACCOUNTING LOGIN

Commands

aaa accounting commands

aaa authentication login

aaa accounting login

aaa accounting update

accounting login

radius-server host

tacacs-server host

613-50137-01 Rev A Command Reference for FS980M Series 1063

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA ACCOUNTING UPDATE

aaa accounting update

Overview This command enables periodic accounting reporting to either the RADIUS or

TACACS+ accounting server(s) wherever login accounting has been configured.

Note that unlimited RADIUS servers and up to four TACACS+ servers can be

configured and consulted for accounting. The first server configured is regarded as

the primary server and if the primary server fails then the backup servers are

consulted in turn. A backup server is consulted if the primary server fails, i.e. is

unreachable.

Use the no variant of this command to disable periodic accounting reporting to

the accounting server(s).

Syntax aaa accounting update [periodic <1-65535>]

no aaa accounting update

Default Periodic accounting update is disabled by default.

Mode Global Configuration

Usage Use this command to enable the device to send periodic AAA login accounting

reports to the accounting server. When periodic accounting report is enabled,

interim accounting records are sent according to the interval specified by the

periodic parameter. The accounting updates are start messages.

If the no variant of this command is used to disable periodic accounting reporting,

any interval specified by the periodic parameter is reset to the default of 30

minutes when accounting reporting is reenabled, unless this interval is specified.

Examples To configure the switch to send period accounting updates every 30 minutes, the

default period, use the following commands:

awplus# configure terminal

awplus(config)# aaa accounting update

To configure the switch to send period accounting updates every 10 minutes, use

the following commands:

awplus# configure terminal

awplus(config)# aaa accounting update periodic 10

Parameter Description

periodic Send accounting records periodically.

<1-65535>The interval to send accounting updates (in minutes). The default is

30 minutes.

613-50137-01 Rev A Command Reference for FS980M Series 1064

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA ACCOUNTING UPDATE

To disable periodic accounting update wherever accounting has been configured,

use the following commands:

awplus# configure terminal

awplus(config)# no aaa accounting update

Commands

aaa accounting auth-mac

aaa accounting auth-web

aaa accounting dot1x

aaa accounting login

613-50137-01 Rev A Command Reference for FS980M Series 1065

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA AUTHENTICATION AUTH-MAC

aaa authentication auth-mac

Overview This command enables MAC-based authentication globally and allows you to

enable an authentication method list (in this case, a list of RADIUS servers). It is

automatically applied to every interface running MAC-based authentication.

Use the no variant of this command to disable MAC-based authentication globally.

Syntax aaa authentication auth-mac default group {<group-name>|radius}

no aaa authentication auth-mac default

Default MAC-based Port Authentication is disabled by default.

Mode Global Configuration

Usage There are two ways to define servers where RADIUS accounting messages are sent:

•group radius: use all RADIUS servers configured by radius-server host

command

•group <group-name>: use the specified RADIUS server group configured

with the aaa group server command

All configured RADIUS Servers are automatically members of the server group

radius. If a server is added to a named group <group-name>, it also remains a

member of the group radius.

Examples To enable MAC-based authentication globally for all RADIUS servers, and use all

available RADIUS servers, use the commands:

awplus# configure terminal

awplus(config)# aaa authentication auth-mac default group

radius

To disable MAC-based authentication, use the commands:

awplus# configure terminal

awplus(config)# no aaa authentication auth-mac default

Commands

aaa accounting auth-mac

aaa group server

auth-mac enable

Parameter Description

default Configure the default authentication method list

group Use a server group

<group-name>Server group name.

radius Use all RADIUS servers.

613-50137-01 Rev A Command Reference for FS980M Series 1066

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA AUTHENTICATION AUTH-MAC

radius-server host

613-50137-01 Rev A Command Reference for FS980M Series 1067

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA AUTHENTICATION AUTH-WEB

aaa authentication auth-web

Overview This command enables Web-based authentication globally and allows you to

enable an authentication method list (in this case, a list of RADIUS servers). It is

automatically applied to every interface running Web-based authentication.

Use the no variant of this command to disable Web-based authentication globally.

Syntax aaa authentication auth-web default group {<group-name>|radius}

no aaa authentication auth-web default

Default Web-based authentication is disabled by default.

Mode Global Configuration

Usage There are two ways to define servers where RADIUS accounting messages are sent:

•group radius: use all RADIUS servers configured by radius-server host

command

•group <group-name>: use the specified RADIUS server group configured

with the aaa group server command

Note that you need to configure an IPv4 address for the VLAN interface on which

Web authentication is running.

Examples To enable Web-based authentication globally for all RADIUS servers, and use all

available RADIUS servers, use the commands:

awplus# configure terminal

awplus(config)# aaa authentication auth-web default group

radius

To disable Web-based authentication, use the commands:

awplus# configure terminal

awplus(config)# no aaa authentication auth-web default

Commands

aaa accounting auth-web

aaa group server

radius-server host

Parameter Description

default Configure the default authentication method list

group Use a server group

<group-name>Server group name.

radius Use all RADIUS servers.

613-50137-01 Rev A Command Reference for FS980M Series 1068

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA AUTHENTICATION DOT1X

aaa authentication dot1x

Overview This command enables IEEE 802.1X-based authentication globally and allows you

to enable an authentication method list (in this case, a list of RADIUS servers). It is

automatically applied to every interface running IEEE 802.1X-based

authentication.

Use the no variant of this command to disable 802.1X-based authentication

globally.

Syntax aaa authentication dot1x default group {<group-name>|radius}

no aaa authentication dot1x default

Default 802.1X-based Port Authentication is disabled by default.

Mode Global Configuration

Usage There are two ways to define servers where RADIUS accounting messages are sent:

•group radius: use all RADIUS servers configured by radius-server host

command

•group <group-name>: use the specified RADIUS server group configured

with the aaa group server command

Examples To enable 802.1X-based authentication globally with all RADIUS servers, and use

all available RADIUS servers, use the command:

awplus# configure terminal

awplus(config)# aaa authentication dot1x default group radius

To disable 802.1X-based authentication, use the command:

awplus# configure terminal

awplus(config)# no aaa authentication dot1x default

Commands

aaa accounting dot1x

aaa group server

dot1x port-control

radius-server host

Parameter Description

default Configure the default authentication method list

group Use a server group

<group-name>Server group name.

radius Use all RADIUS servers.

613-50137-01 Rev A Command Reference for FS980M Series 1069

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA AUTHENTICATION ENABLE DEFAULT GROUP TACACS+

aaa authentication enable default group

tacacs+

Overview This command enables AAA authentication to determine the privilege level a user

can access for passwords authenticated against the TACACS+ server.

Use the no variant of this command to disable privilege level authentication.

Syntax aaa authentication enable default group tacacs+ [local] [none]

no aaa authentication enable default

Default Local privilege level authentication is enabled by default (aaa authentication

enable default local command).

Mode Global Configuration

Usage A user is configured on a TACACS+ server with a maximum privilege level. When

they enter the enable (Privileged Exec mode) command they are prompted for an

enable password which is authenticated against the TACACS+ server. If the

password is correct and the specified privilege level is equal to or less than the

users maximum privilege level, then they are granted access to that level. If the

user attempts to access a privilege level that is higher than their maximum

configured privilege level, then the authentication session will fail and they will

remain at their current privilege level.

NOTE: If both local and none are specified, you must always specify local first.

If the TACACS+ server goes offline, or is not reachable during enable password

authentication, and command level authentication is configured as:

•aaa authentication enable default group tacacs+

then the user is never granted access to Privileged Exec mode.

•aaa authentication enable default group tacacs+ local

then the user is authenticated using the locally configured enable password,

which if entered correctly grants the user access to Privileged Exec mode. If

no enable password is locally configured (enable password command),

then the enable authentication will fail until the TACACS+ server becomes

available again.

Parameter Description

local Use the locally configured enable password ( enable password

command) for authentication.

none No authentication.

613-50137-01 Rev A Command Reference for FS980M Series 1070

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA AUTHENTICATION ENABLE DEFAULT GROUP TACACS+

•aaa authentication enable default group tacacs+ none

then the user is granted access to Privileged Exec mode with no

authentication. This is true even if a locally configured enable password is

configured.

•aaa authentication enable default group tacacs+ local none

then the user is authenticated using the locally configured enable password.

If no enable password is locally configured, then the enable authentication

will grant access to Privileged Exec mode with no authentication.

If the password for the user is not successfully authenticated by the server, then the

user is again prompted for an enable password when they enter enable via the CLI.

Examples To enable a privilege level authentication method that will not allow the user to

access Privileged Exec mode if the TACACS+ server goes offline, or is not reachable

during enable password authentication, use the following commands:

awplus# configure terminal

awplus(config)# aaa authentication enable default group tacacs+

To enable a privilege level authentication method that will allow the user to access

Privileged Exec mode if the TACACS+ server goes offline, or is not reachable during

enable password authentication, and a locally configured enable password is

configured, use the following commands:

awplus# configure terminal

awplus(config)# aaa authentication enable default group tacacs+

local

To disable privilege level authentication, use the following commands:

awplus# configure terminal

awplus(config)# no aaa authentication enable default

Commands

aaa authentication login

aaa authentication enable default local

enable (Privileged Exec mode)

enable password

enable secret

tacacs-server host

613-50137-01 Rev A Command Reference for FS980M Series 1071

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA AUTHENTICATION ENABLE DEFAULT LOCAL

aaa authentication enable default local

Overview This command enables AAA authentication to determine the privilege level a user

can access for passwords authenticated locally.

Syntax aaa authentication enable default local

Default Local privilege level authentication is enabled by default.

Mode Global Configuration

Usage The privilege level configured for a particular user in the local user database is the

privilege threshold above which the user is prompted for an enable (Privileged

Exec mode) command.

Examples To enable local privilege level authentication command, use the following

commands:

awplus# configure terminal

awplus(config)# aaa authentication enable default local

To disable privilege level authentication, use the following commands:

awplus# configure terminal

awplus(config)# no aaa authentication enable default

Commands

aaa authentication enable default group tacacs+

aaa authentication login

enable (Privileged Exec mode)

enable password

enable secret

tacacs-server host

613-50137-01 Rev A Command Reference for FS980M Series 1072

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA AUTHENTICATION LOGIN

aaa authentication login

Overview Use this command to create an ordered list of methods to use to authenticate user

more of the options local or group, in the order you want them to be applied. If

the default method list name is specified, it is applied to every console and VTY

line immediately unless another method list is applied to that line by the login

authentication command. To apply a non-default method list, you must also use

the login authentication command.

Use the no variant of this command to remove an authentication method list for

user login. The specified method list name is deleted from the configuration. If the

method list name has been applied to any console or VTY line, user login

authentication on that line will fail.

Note that the no aaa authentication login default command does not remove

the default method list. This will return the default method list to its default state

(local is the default).

Syntax aaa authentication login {default|<list-name>} {[local] [group

{radius|tacacs+|<group-name>}]}

no aaa authentication login {default|<list-name>}

Default If the default server is not configured using this command, user login

authentication uses the local user database only.

If the default method list name is specified, it is applied to every console and VTY

line immediately unless a named method list server is applied to that line by the

loginauthentication command.

local is the default state for the default method list unless a named method list is

applied to that line by the login authentication command. Reset to the default

method list using the no aaa authentication login default command.

Mode Global Configuration

Parameter Description

default Set the default authentication server for user login.

<list-name>Name of authentication server.

local Use the local username database.

group Use server group.

radius Use all RADIUS servers configured by the radius-server

host command.

tacacs+ Use all TACACS+ servers configured by the tacacs-server

host command.

<group-name>Use the specified RADIUS server group, as configured by

the aaa group server command.

613-50137-01 Rev A Command Reference for FS980M Series 1073

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA AUTHENTICATION LOGIN

Usage When a user attempts to log in, the switch sends an authentication request to the

first authentication server in the method list. If the first server in the list is reachable

and it contains a username and password matching the authentication request,

the user is authenticated and the login succeeds. If the authentication server

denies the authentication request because of an incorrect username or password,

the user login fails. If the first server in the method list is unreachable, the switch

sends the request to the next server in the list, and so on.

For example, if the method list specifies group tacacs+ local, and a user attempts

to log in with a password that does not match a user entry in the first TACACS+

server, if this TACACS+ server denies the authentication request, then the switch

does not try any other TACACS+ servers not the local user database; the user login

fails.

Examples To configure the default authentication method list for user login to first use all

available RADIUS servers for user login authentication, and then use the local user

database, use the following commands:

awplus# configure terminal

awplus(config)# aaa authentication login default group radius

local

To configure a user login authentication method list called USERS to first use the

RADIUS server group RAD_GROUP1 for user login authentication, and then use the

local user database, use the following commands:

awplus# configure terminal

awplus(config)# aaa authentication login USERS group RAD_GROUP1

local

To configure a user login authentication method list called USERS to first use the

TACACS+ servers for user login authentication, and then use the local user

database, use the following commands:

awplus# configure terminal

awplus(config)# aaa authentication login USERS group tacacs+

local

To return to the default method list (local is the default server), use the following

commands:

awplus# configure terminal

awplus(config)# no aaa authentication login default

To delete an existing authentication method list USERS created for user login

authentication, use the following commands:

awplus# configure terminal

awplus(config)# no aaa authentication login USERS

Commands

aaa accounting commands

aaa authentication enable default group tacacs+

613-50137-01 Rev A Command Reference for FS980M Series 1074

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA AUTHORIZATION COMMANDS

aaa authorization commands

Overview This command configures a method list for commands authorization that can be

applied to console or VTY lines. When command authorization is enabled for a

privilege level, only authorized users can executed commands in that privilege

level.

Use the no variant of this command to remove a named method list or disable the

default method list for a privilege level.

Syntax aaa authorization commands <privilege-level>

{default|<list-name>} group tacac+ [none]

no aaa authorization commands <privilege-level>

{default|<list-name>}

Mode Global Configuration

Usage TACACS+ command authorization provides centralized control of the commands

available to a user of an AlliedWare Plus device. Once enabled:

• The command string and username are encrypted and sent to the first

available configured TACACS+ server (the first server configured) for

authorization.

Parameter Description

<privilege-level> The privilege level of the set of commands the method list

will be applied to.

AlliedWare Plus defines three sets of commands, that are

indexed by a level value:

Level = 1: All commands that can be accessed by a user

with privilege level between 1 and 6 inclusive

Level = 7: All commands that can be accessed by a user

with privilege level between 7 and 14 inclusive

Level = 15: All commands that can be accessed by a user

with privilege level 15

group Specify the server group where authorization messages are

sent. Only the tacacs+ group is available for this

command.

tacac+ Use all TACACS+ servers configured by the tacacs-server

host command.

default Configure the default authorization commands method list.

<list-name>Configure a named authorization commands method list

none If specified, this provides a local fallback to command

authorization so that if authorization servers become

unavailable then the device will accept all commands

normally allowed for the privilege level of the user.

613-50137-01 Rev A Command Reference for FS980M Series 1075

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA AUTHORIZATION COMMANDS

• The TACACS+ server decides if the user is authorized to execute the

command and returns the decision to the AlliedWare Plus device.

• Depending on this decision the device will then either execute the

command or notify the user that authorization has failed.

If multiple TACACS+ servers are configured, and the first server is unreachable or

does not respond, the other servers will be queried, in turn, for an authorization

decision. If all servers are unreachable and a local fallback has been configured,

with the none parameter, then commands are authorized based on the user’s

privilege level; the same behavior as if command authorization had not been

configured. If, however, the local fallback is not configured and all servers become

unreachable then all commands except logout, exit, and quit will be denied.

The default method list is defined with a local fallback unless configured

differently using this command.

Example To configure a commands authorization method list, named TAC15, using all

TACACS+ servers to authorize commands for privilege level 15, with a local

fallback, use the following commands:

awplus# configure terminal

awplus(config)# aaa authorization commands 15 TAC15 group

tacacs+ none

To configure the default method list to authorize commands for privilege level 7,

with no local fallback, use the following commands:

awplus# configure terminal

awplus(config)# aaa authorization commands 7 default group

tacacs+

To remove the authorization method list TAC15, use the following commands:

awplus# configure terminal

awplus(config)# no aaa authorization commands 15 TAC15

Commands

aaa authorization config-commands

authorization commands

tacacs-server host

Command

changes

Version 5.4.6-2.1: command added

613-50137-01 Rev A Command Reference for FS980M Series 1076

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA AUTHORIZATION CONFIG-COMMANDS

aaa authorization config-commands

Overview Use this command to enable command authorization on configuration mode

commands. By default, command authorization applies to commands in exec

mode only.

Use the no variant of this command to disable command authorization on

configuration mode commands.

Syntax aaa authorization config-commands

no aaa authorization config-commands

Default By default, command authorization is disabled on configuration mode commands.

Mode Global Configuration

Usage If authorization of configuration mode commands is not enabled then all

configuration commands are accepted by default, including command

authorization commands.

NOTE: Authorization of configuration commands is required for a secure TACACS+

command authorization configuration as it prevents the feature from being disabled

to gain access to unauthorized exec mode commands.

Example To enable command authorization for configuration mode commands, use the

commands:

awplus# configure terminal

awplus(config)# aaa authorization config-commands

To disable command authorization for configuration mode commands, use the

commands:

awplus# configure terminal

awplus(config)# no aaa authorization config-commands

Commands

aaa authorization commands

authorization commands

tacacs-server host

Command

changes

Version 5.4.6-2.1: command added

613-50137-01 Rev A Command Reference for FS980M Series 1077

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA GROUP SERVER

aaa group server

Overview This command configures a RADIUS server group. A server group can be used to

specify a subset of RADIUS servers in aaa commands. The group name radius is

predefined, which includes all RADIUS servers configured by the radius-server

host command.

RADIUS servers are added to a server group using the server command. Each

RADIUS server should be configured using the radius-server host command.

Use the no variant of this command to remove an existing RADIUS server group.

Syntax aaa group server radius <group-name>

no aaa group server radius <group-name>

Mode Global Configuration

Usage Use this command to create an AAA group of RADIUS servers, and to enter Server

Group Configuration mode, in which you can add servers to the group. Use a server

group to specify a subset of RADIUS servers in AAA commands. Each RADIUS server

must be configured by the radius-server host command. To add RADIUS servers

to a server group, use the server command.

Examples To create a RADIUS server group named GROUP1 with hosts 192.168.1.1,

192.168.2.1 and 192.168.3.1, use the commands:

awplus(config)# aaa group server radius GROUP1

awplus(config-sg)# server 192.168.1.1 auth-port 1812 acct-port

1813

awplus(config-sg)# server 192.168.2.1 auth-port 1812 acct-port

1813

awplus(config-sg)# server 192.168.3.1 auth-port 1812 acct-port

1813

To remove a RADIUS server group named GROUP1 from the configuration, use the

command:

awplus(config)# no aaa group server radius GROUP1

Parameter Description

<group-name>Server group name.

613-50137-01 Rev A Command Reference for FS980M Series 1078

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA GROUP SERVER

Commands

aaa accounting auth-mac

aaa accounting auth-web

aaa accounting dot1x

aaa accounting login

aaa authentication auth-mac

aaa authentication auth-web

aaa authentication dot1x

aaa authentication login

radius-server host

server (Server Group)

613-50137-01 Rev A Command Reference for FS980M Series 1079

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA LOCAL AUTHENTICATION ATTEMPTS LOCKOUT-TIME

aaa local authentication attempts

lockout-time

Overview This command configures the duration of the user lockout period.

Use the no variant of this command to restore the duration of the user lockout

period to its default of 300 seconds (5 minutes).

Syntax aaa local authentication attempts lockout-time <lockout-tiime>

no aaa local authentication attempts lockout-time

Mode Global Configuration

Default The default for the lockout-time is 300 seconds (5 minutes).

Usage While locked out all attempts to login with the locked account will fail. The lockout

can be manually cleared by another privileged account using the clear aaa local

user lockout command.

Examples To configure the lockout period to 10 minutes (600 seconds), use the commands:

awplus# configure terminal

awplus(config)# aaa local authentication attempts lockout-time

600

To restore the default lockout period of 5 minutes (300 seconds), use the

commands:

awplus# configure terminal

awplus(config)# no aaa local authentication attempts

lockout-time

Commands

aaa local authentication attempts max-fail

Parameter Description

<lockout-time><0-10000>. Time in seconds to lockout the user.

613-50137-01 Rev A Command Reference for FS980M Series 1080

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA LOCAL AUTHENTICATION ATTEMPTS MAX-FAIL

aaa local authentication attempts max-fail

Overview This command configures the maximum number of failed login attempts before a

user account is locked out. Every time a login attempt fails the failed login counter

is incremented.

Use the no variant of this command to restore the maximum number of failed

Syntax aaa local authentication attempts max-fail <failed-logins>

no aaa local authentication attempts max-fail

Mode Global Configuration

Default The default for the maximum number of failed login attempts is five failed login

attempts.

Usage When the failed login counter reaches the limit configured by this command that

user account is locked out for a specified duration configured by the aaa local

authentication attempts lockout-time command.

When a successful login occurs the failed login counter is reset to 0. When a user

account is locked out all attempts to login using that user account will fail.

Examples To configure the number of login failures that will lock out a user account to two

awplus# configure terminal

awplus(config)# aaa local authentication attempts max-fail 2

To restore the number of login failures that will lock out a user account to the

default number of login attempts (five login attempts), use the commands:

awplus# configure terminal

awplus(config)# no aaa local authentication attempts max-fail

Commands

aaa local authentication attempts lockout-time

clear aaa local user lockout

Parameter Description

<failed-logins><1-32>. Number of login failures allowed before locking out a

user.

613-50137-01 Rev A Command Reference for FS980M Series 1081

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AAA LOGIN FAIL-DELAY

aaa login fail-delay

Overview Use this command to configure the minimum time period between failed login

attempts. This setting applies to login attempts via the console, SSH and Telnet.

Use the no variant of this command to reset the minimum time period to its default

value.

Syntax aaa login fail-delay [<1-10>]

no aaa login fail-delay [<1-10>]

Default 1 second

Mode Global configuration

Example To apply a delay of at least 5 seconds between login attempts, use the following

commands:

awplus# configure terminal

awplus(config)# aaa login fail-delay 5

Commands

aaa authentication login

Parameter Description

<1-10> The minimum number of seconds required between login

attempts

613-50137-01 Rev A Command Reference for FS980M Series 1082

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

ACCOUNTING LOGIN

accounting login

Overview This command applies a login accounting method list to console or VTY lines for

user login. When login accounting is enabled using this command, logging events

generate an accounting record to the accounting server.

The accounting method list must be configured first using this command. If an

accounting method list is specified that has not been created by this command

then accounting will be disabled on the specified lines.

The no variant of this command resets AAA Accounting applied to console or VTY

lines for local or remote login. default login accounting is applied after issuing the

no accounting login command. Accounting is disabled with default.

Syntax accounting login {default|<list-name>}

no accounting login

Default By default login accounting is disabled in the default accounting server. No

accounting will be performed until accounting is enabled using this command.

Mode Line Configuration

Examples To apply the accounting server USERS to all VTY lines, use the following

commands:

awplus# configure terminal

awplus(config)# line vty 0 32

awplus(config-line)# accounting login USERS

Commands

aaa accounting commands

aaa accounting login

Parameter Description

default Default accounting method list.

<list-name>Named accounting method list.

613-50137-01 Rev A Command Reference for FS980M Series 1083

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AUTHORIZATION COMMANDS

authorization commands

Overview This command applies a command authorization method list, defined using the

aaa authorization commands command, to console and VTY lines.

Use the no variant of this command to reset the command authorization

configuration on the console and VTY lines.

Syntax authorization commands <privilege-level> {default|<list-name>}

no authorization commands <privilege-level>

Default The default method list is applied to each console and VTY line by default.

Mode Line Configuration

Usage If the specified method list does not exist users will not be enable to execute any

commands in the specified method list on the specified VTY lines.

Example To apply the TAC15 command authorization method list with privilege level 15 to

VTY lines 0 to 5, use the following commands:

awplus# configure terminal

awplus(config)# line vty 0 5

awplus(config-line)# authorization commands 15 TAC15

To reset the command authorization configuration with privilege level 15 on VTY

lines 0 to 5, use the following commands:

awplus# configure terminal

awplus(config)# line vty 0 5

awplus(config-line)# no authorization commands 15

Commands

aaa authorization commands

Parameter Description

<privilege-level> The privilege level of the set of commands the method list

will be applied to.

AlliedWare Plus defines three sets of commands, that are

indexed by a level value:

Level = 1: All commands that can be accessed by a user with

privilege level between 1 and 6 inclusive

Level = 7: All commands that can be accessed by a user with

privilege level between 7 and 14 inclusive

Level = 15: All commands that can be accessed by a user

with privilege level 15

default Configure the default authorization commands method list.

<list-name>Configure a named authorization commands method list

613-50137-01 Rev A Command Reference for FS980M Series 1084

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

AUTHORIZATION COMMANDS

aaa authorization config-commands

tacacs-server host

Command

changes

Version 5.4.6-2.1: command added

613-50137-01 Rev A Command Reference for FS980M Series 1085

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

CLEAR AAA LOCAL USER LOCKOUT

clear aaa local user lockout

Overview Use this command to clear the lockout on a specific user account or all user

accounts.

Syntax clear aaa local user lockout {username <username>|all}

Mode Privileged Exec

Examples To unlock the user account ‘bob’ use the following command:

awplus# clear aaa local user lockout username bob

To unlock all user accounts use the following command:

awplus# clear aaa local user lockout all

Commands

aaa local authentication attempts lockout-time

Parameter Description

username Clear lockout for the specified user.

<username> Specifies the user account.

all Clear lockout for all user accounts.

613-50137-01 Rev A Command Reference for FS980M Series 1086

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

DEBUG AAA

debug aaa

Overview This command enables AAA debugging.

Use the no variant of this command to disable AAA debugging.

Syntax debug aaa [accounting|all|authentication|authorization]

no debug aaa [accounting|all|authentication|authorization]

Default AAA debugging is disabled by default.

Mode Privileged Exec

Examples To enable authentication debugging for AAA, use the command:

awplus# debug aaa authentication

To disable authentication debugging for AAA, use the command:

awplus# no debug aaa authentication

Commands

show debugging aaa

undebug aaa

Parameter Description

accounting Accounting debugging.

all All debugging options are enabled.

authentication Authentication debugging.

authorization Authorization debugging.

613-50137-01 Rev A Command Reference for FS980M Series 1087

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

Overview Use this command to apply an AAA server for authenticating user login attempts

from a console or remote logins on these console or VTY lines. The authentication

method list must be specified by the aaa authentication login command. If the

method list has not been configured by the aaa authentication login command,

Use the no variant of this command to reset AAA Authentication configuration to

use the default method list for login authentication on these console or VTY lines.

Command

Syntax

no login authentication

Default The default login authentication method list, as specified by the aaa

authentication login command, is used to authenticate user login. If this has not

been specified, the default is to use the local user database.

Mode Line Configuration

Examples To reset user authentication configuration on all VTY lines, use the following

commands:

awplus# configure terminal

awplus(config)# line vty 0 32

awplus(config-line)# no login authentication

Commands

aaa authentication login

line

Parameter Description

default The default authentication method list. If the default method

list has not been configured by the aaa authentication login

command, the local user database is used for user login

authentication.

<list-name> Named authentication server.

613-50137-01 Rev A Command Reference for FS980M Series 1088

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

PROXY-PORT

proxy-port

Overview Use this command to change the local UDP port used for communication between

local RADIUS client applications and the RadSecProxy AAA application. Any

unused UDP port may be selected. The default port is 1645.

Use the no variant of this command to change the UDP port back to the default of

1645.

Syntax proxy-port <port>

no proxy-port

Default The default port is 1645.

Mode RadSecProxy AAA Configuration Mode

Usage It is not necessary to change the value from the default unless UDP port 1645 is

required for another purpose.RADIUS requests received on this port from external

devices will be ignored. The port is only used for local (intra-device)

communication.

Example To configure change the UDP port to 7001, use the following commands:

awplus# configure terminal

awplus(config)# radius-secure-proxy aaa

awplus(config-radsecproxy-aaa)# proxy-port 7001

Commands

radius-secure-proxy aaa

server (radsecproxy-aaa)

server name-check

server trustpoint

Parameter Description

<port> UDP Port Number, 1-65536.

613-50137-01 Rev A Command Reference for FS980M Series 1089

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

RADIUS-SECURE-PROXY AAA

radius-secure-proxy aaa

Overview Use this command to enter the RadSecProxy AAA (authentication, authorization,

and accounting) application configuration mode. This application allows local

RADIUS-based clients on system to communicate with remote RadSec servers via

a secure (TLS) proxy.

Syntax radius-secure-proxy aaa

Mode Global Configuration Mode

Example To change mode from User Exec mode to the RadSecProxy AAA configuration

mode, use the commands:

awplus# configure terminal

awplus(config)# radius-secure-proxy aaa

awplus(config-radsecproxy-aaa)#

Commands

proxy-port

server (radsecproxy-aaa)

server name-check

server trustpoint

613-50137-01 Rev A Command Reference for FS980M Series 1090

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

SERVER (RADSECPROXY-AAA)

server (radsecproxy-aaa)

Overview Use this command to add a server to the RadSecProxy AAA application. Local

RADIUS client applications will attempt, via the proxy, to communicate with any

RadSec servers that are operational (in addition to any non-TLS RADIUS servers

that are configured).

Use the no variant of this command to delete a previously-configured server from

the RadSecProxy AAA application.

Syntax server {<hostname>|<ip-addr>} [timeout <1-1000>] [name-check

{on|off}]

no server {<hostname>|<ip-addr>}

Mode RadSecProxy AAA Configuration Mode

Usage The server may be specified by its domain name or by its IPv4 address. If a domain

name is used, it must be resolvable using a configured DNS name server.

Each server may be configured with a timeout; if not specified, the global timeout

value for RADIUS servers will be used. The global timeout may be changed using

the radius-server timeout command. The default global timeout is 5 seconds.

Each server may be configured to use certificate name-checking; if not specified,

the global behavior defined by server name-check or no server name-check will

be used. If name checking is enabled, the Common Name portion of the subject

field of the server’s X.509 certificate must match the domain name or IP address

specified in this command.

Parameter Description

<hostname>Hostname of RadSec server

<ip-addr>Specify the client IPv4 address, in dotted decimal notation

(A.B.C.D).

timeout Specify the amount of time that the RadSecProxy AAA application

should wait before receiving replies from this server. RADIUS

server timeout (which defaults to 5 seconds).

<1-1000> Time in seconds to wait for a server reply.

name-check Specify whether or not to enforce certificate name checking for

this client. If the parameter is not specified then the global

behavior, which defaults to on, is used.

on Enable name checking for this client.

off Disable name checking for this client.

613-50137-01 Rev A Command Reference for FS980M Series 1091

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

SERVER (RADSECPROXY-AAA)

Example To add a server which waits 3 seconds before receiving replies, use the commands:

awplus# configure terminal

awplus(config)# radius-secure-proxy aaa

awplus(config-radsecproxy-aaa)# client mynas.local name-check

off

Commands

proxy-port

radius-secure-proxy aaa

server name-check

server trustpoint

613-50137-01 Rev A Command Reference for FS980M Series 1092

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

SERVER MUTUAL-AUTHENTICATION

server mutual-authentication

Overview This command enables or disables mutual certificate authentication for all

RadSecProxy servers. When enabled, the RadSecProxy AAA application will send a

local X.509 certificate to the server when establishing a TLS connection.

Use the no variant of this command to disable mutual certificate validation

causing the RadSecProxy AAA application to not transmit a certificate to the server.

NOTE: If mutual authentication is disabled on the client (AAA) application but enabled

on the server, a connection will not be established.

Syntax server mutual-authentication

no server mutual-authentication

Default Mutual authentication is enabled by default.

Mode RadSecProxy AAA Configuration Mode

Example Disable mutual certificate validation with the following command:

awplus# configure terminal

awplus(config)# radius-secure-proxy aaa

awplus(config-radsecproxy-aaa)# no server

mutual-authentication

Commands

radius-secure-proxy aaa

server name-check

server (radsecproxy-aaa)

Command

changes

Version 5.4.6-2.1: command added

613-50137-01 Rev A Command Reference for FS980M Series 1093

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

SERVER NAME-CHECK

server name-check

Overview This command sets the global behavior for certificate name-checking for the

RadSecProxy AAA application to on. This behavior will be used for all servers

associated with the application that do not specify a behavior on a per-server basis.

If name-checking is enabled, the Common Name portion of the subject field of the

client’s X.509 certificate must match the domain name or IP address specified in

the server (radsecproxy-aaa) command.

Use the no variant of this command to set the global behavior for certificate name

checking to off

Syntax server name-check

no server name-check

Default Certificate name checking is on by default.

Mode RadSecProxy AAA Configuration Mode

Example Disable certificate name checking globally with the following command:

awplus# configure terminal

awplus(config)# radius-secure-proxy aaa

awplus(config-radsecproxy-aaa)# no server name-check

Commands

proxy-port

radius-secure-proxy aaa

server (radsecproxy-aaa)

server trustpoint

613-50137-01 Rev A Command Reference for FS980M Series 1094

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

SERVER TRUSTPOINT

server trustpoint

Overview This command adds one or more trustpoints to be used with the RadSecProxy AAA

application. Multiple trustpoints may be specified, or the command may be

executed more than once, to add multiple trustpoints to the application.

The no version of this command removes one or more trustpoints from the list of

trustpoints associated with the application.

Syntax server trustpoint [<trustpoint-list>]

no server trustpoint [<trustpoint-list>]

Default By default, no trustpoints are associated with the application.

Mode RadSecProxy AAA Configuration Mode

Usage The device certificate associated with first trustpoint added to the application will

be transmitted to remote servers. The certificate received from the remote server

must have an issuer chain that terminates with the root CA certificate for any of the

trustpoints that are associated with the application.

If no trustpoints are specified in the command, the trustpoint list will be

unchanged.

If no server trustpoint is issued without specifying any trustpoints, then all

trustpoints will be disassociated from the application.

Example You can add multiple trustpoints to the RadSecProxy AAA application by

executing the command multiple times:

awplus# configure terminal

awplus(config)# radius-secure-proxy aaa

awplus(config-radsecproxy-aaa)# server trustpoint example_1

awplus(config-radsecproxy-aaa)# server trustpoint example_2

Alternatively, add multiple trustpoints with a single command:

awplus(config-radsecproxy-aaa)# server trustpoint example_3

example_4

Disassociate all trustpoints from the RadSecProxy AAA application using the

command:

awplus(config-radsecproxy-aaa)# no server trustpoint

Commands

proxy-port

radius-secure-proxy aaa

Parameter Description

<trustpoint-list> Specify one or more trustpoints to be added or deleted.

613-50137-01 Rev A Command Reference for FS980M Series 1095

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

SERVER TRUSTPOINT

server (radsecproxy-aaa)

server name-check

613-50137-01 Rev A Command Reference for FS980M Series 1096

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

SHOW AAA LOCAL USER LOCKED

show aaa local user locked

Overview This command displays the current number of failed attempts, last failure time and

location against each user account attempting to log into the device.

Note that once the lockout count has been manually cleared by another privileged

account using the clear aaa local user lockout command or a locked account

successfully logs into the system after waiting for the lockout time, this command

will display nothing for that particular account.

Syntax show aaa local user locked

Mode User Exec and Privileged Exec

Example To display the current failed attempts for local users, use the command:

awplus# show aaa local user locked

Output Figure 30-1: Example output from the show aaa local user locked command

Commands

aaa local authentication attempts lockout-time

aaa local authentication attempts max-fail

clear aaa local user lockout

awplus# show aaa local user locked

bob 3 05/23/14 16:21:37 ttyS0

manager 5 05/23/14 16:31:44 192.168.1.200

613-50137-01 Rev A Command Reference for FS980M Series 1097

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

SHOW DEBUGGING AAA

show debugging aaa

Overview This command displays the current debugging status for AAA (Authentication,

Authorization, Accounting).

Syntax show debugging aaa

Mode User Exec and Privileged Exec

Example To display the current debugging status of AAA, use the command:

awplus# show debug aaa

Output Figure 30-2: Example output from the show debug aaa command

AAA debugging status:

Authentication debugging is on

Accounting debugging is off

613-50137-01 Rev A Command Reference for FS980M Series 1098

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

AAA COMMANDS

UNDEBUG AAA

undebug aaa

Overview This command applies the functionality of the no debug aaa command.

613-50137-01 Rev A Command Reference for FS980M Series 1099

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS Commands

Introduction

Overview This chapter provides an alphabetical reference for commands used to configure

the device to use RADIUS servers.

Command List •“auth radius send nas-identifier” on page 1100

•“auth radius send service-type” on page 1101

•“deadtime (RADIUS server group)” on page 1102

•“debug radius” on page 1103

•“ip radius source-interface” on page 1104

•“radius-server deadtime” on page 1105

•“radius-server host” on page 1106

•“radius-server key” on page 1109

•“radius-server retransmit” on page 1110

•“radius-server timeout” on page 1112

•“server (Server Group)” on page 1114

•“show debugging radius” on page 1116

•“show radius” on page 1117

•“show radius statistics” on page 1120

•“undebug radius” on page 1121

613-50137-01 Rev A Command Reference for FS980M Series 1100

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

AUTH RADIUS SEND NAS-IDENTIFIER

auth radius send nas-identifier

Overview Use this command to enable the device to include the NAS-Identifier(32) attribute

in RADIUS authentication requests.

Use the no variant of this command to stop including the NAS-Identifier attribute.

Syntax auth radius send nas-identifier [<name>|vlan-id]

no auth radius send nas-identifier

Mode Global Configuration

Example To use a user-defined identifier of NASID100 as the NAS-Identifier attribute, use the

commands:

awplus# configure terminal

awplus(config)# auth radius send nas-identifier NASID100

To use the VLAN ID as the NAS-Identifier attribute, use the commands:

awplus# configure terminal

awplus(config)# auth radius send nas-identifier vlan-id

To stop sending the NAS-Identifier attribute, use the commands:

awplus# configure terminal

awplus(config)# no auth radius send nas-identifier

Commands

auth radius send service-type

Parameter Description

<name> Send this user-defined text as the NAS-Identifier. You can specify

up to 253 characters.

vlan-id Send the VLAN ID of the authentication port as the NAS-Identifier.

This is the configured VLAN ID, not the dynamic VLAN ID or guest

VLAN ID.

613-50137-01 Rev A Command Reference for FS980M Series 1101

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

AUTH RADIUS SEND SERVICE-TYPE

auth radius send service-type

Overview Use this command to enable the device to include the Service-Type(6) attribute in

RADIUS authentication requests. The Service-Type attribute has a value of:

• Framed(2) for 802.1x

• Call-Check(10) for MAC authentication

• Unbound(5) for Web authentication.

Use the no variant of this command to stop including the Service-Type attribute.

Syntax auth radius send service-type

no auth radius send service-type

Mode Global Configuration

Example To send the Service-Type attribute, use the commands:

awplus# configure terminal

awplus(config)# auth radius send service-type

Commands

auth radius send nas-identifier

613-50137-01 Rev A Command Reference for FS980M Series 1102

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

DEADTIME (RADIUS SERVER GROUP)

deadtime (RADIUS server group)

Overview Use this command to configure the deadtime parameter for the RADIUS server

group. This command overrides the global dead-time configured by the

radius-server deadtime command. The configured deadtime is the time period in

minutes to skip a RADIUS server for authentication or accounting requests if the

server is “dead”. Note that a RADIUS server is considered “dead” if there is no

response from the server within a defined time period.

Use the no variant of this command to reset the deadtime configured for the

RADIUS server group. If the global deadtime for RADIUS server is configured the

value will be used for the servers in the group. The global deadtime for the RADIUS

server is set to 0 minutes by default.

Syntax deadtime <0-1440>

no deadtime

Default The deadtime is set to 0 minutes by default.

Mode Server Group Configuration

Usage If the RADIUS server does not respond to a request packet, the packet is

retransmitted the number of times configured for the retransmit parameter (after

waiting for a timeout period to expire). The server is then marked “dead”, and the

time is recorded. The deadtime parameter configures the amount of time to skip

a dead server; if a server is dead, no request message is sent to the server for the

deadtime period.

Examples To configure the deadtime for 5 minutes for the RADIUS server group “GROUP1”,

use the command:

awplus(config)# aaa group server radius GROUP1

awplus(config-sg)# server 192.168.1.1

awplus(config-sg)# deadtime 5

To remove the deadtime configured for the RADIUS server group “GROUP1”, use

the command:

awplus(config)# aaa group server radius GROUP1

awplus(config-sg)# no deadtime

Commands

aaa group server

radius-server deadtime

Parameter Description

<0-1440>Amount of time in minutes.

613-50137-01 Rev A Command Reference for FS980M Series 1103

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

DEBUG RADIUS

debug radius

Overview This command enables RADIUS debugging. If no option is specified, all debugging

options are enabled.

Use the no variant of this command to disable RADIUS debugging. If no option is

specified, all debugging options are disabled.

Syntax debug radius [packet|event|all]

no debug radius [packet|event|all]

Default RADIUS debugging is disabled by default.

Mode Privileged Exec

Examples To enable debugging for RADIUS packets, use the command:

awplus# debug radius packet

To enable debugging for RADIUS events, use the command:

awplus# debug radius event

To disable debugging for RADIUS packets, use the command:

awplus# no debug radius packet

To disable debugging for RADIUS events, use the command:

awplus# no debug radius event

Commands

show debugging radius

undebug radius

Parameter Description

packet Debugging for RADIUS packets is enabled or disabled.

event Debugging for RADIUS events is enabled or disabled.

all Enable or disable all debugging options.

613-50137-01 Rev A Command Reference for FS980M Series 1104

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

IP RADIUS SOURCE-INTERFACE

ip radius source-interface

Overview This command configures the source IP address of every outgoing RADIUS packet

to use a specific IP address or the IP address of a specific interface. If the specified

interface is down or there is no IP address on the interface, then the source IP

address of outgoing RADIUS packets depends on the interface the packets leave.

Use the no variant of this command to remove the source interface configuration.

The source IP address in outgoing RADIUS packets will be the IP address of the

interface from which the packets are sent.

Syntax ip radius source-interface {<interface>|<ip-address>}

no ip radius source-interface

Default Source IP address of outgoing RADIUS packets depends on the interface the

packets leave.

Mode Global Configuration

Examples To configure all outgoing RADIUS packets to use the IP address of the interface

“vlan1” for the source IP address, use the following commands:

awplus# configure terminal

awplus(config)# ip radius source-interface vlan1

To configure the source IP address of all outgoing RADIUS packets to use

192.168.1.10, use the following commands:

awplus# configure terminal

awplus(config)# ip radius source-interface 192.168.1.10

To reset the source interface configuration for all outgoing RADIUS packets, use

the following commands:

awplus# configure terminal

awplus(config)# no ip radius source-interface

Commands

radius-server host

show radius statistics

Parameter Description

<interface> Interface name.

<ip-address> IP address in the dotted decimal format A.B.C.D.

613-50137-01 Rev A Command Reference for FS980M Series 1105

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

RADIUS-SERVER DEADTIME

radius-server deadtime

Overview Use this command to specify the global deadtime for all RADIUS servers. If a

RADIUS server is considered dead, it is skipped for the specified deadtime. This

command specifies for how many minutes a RADIUS server that is not responding

to authentication requests is passed over by requests for RADIUS authentication.

Use the no variant of this command to reset the global deadtime to the default of

0 seconds, so that RADIUS servers are not skipped even if they are dead.

Syntax radius-server deadtime <minutes>

no radius-server deadtime

Default The default RADIUS deadtime configured on the system is 0 seconds.

Mode Global Configuration

Usage The RADIUS client considers a RADIUS server to be dead if it fails to respond to a

request after it has been retransmitted as often as specified globally by the

radius-server retransmit command or for the server by the radius-server host

command. To improve RADIUS response times when some servers may be

unavailable, set a deadtime to skip dead servers.

Examples To set the dead time of the RADIUS server to 60 minutes, use the following

commands:

awplus# configure terminal

awplus(config)# radius-server deadtime 60

To disable the dead time of the RADIUS server, use the following commands:

awplus# configure terminal

awplus(config)# no radius-server deadtime

Commands

deadtime (RADIUS server group)

radius-server host

radius-server retransmit

show radius statistics

Parameter Description

<minutes> RADIUS server deadtime in minutes in the range 0 to 1440 (24 hours).

613-50137-01 Rev A Command Reference for FS980M Series 1106

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

RADIUS-SERVER HOST

radius-server host

Overview Use this command to specify a remote RADIUS server host for authentication or

accounting, and to set server-specific parameters. The parameters specified with

this command override the corresponding global parameters for RADIUS servers.

This command specifies the IP address or host name of the remote RADIUS server

host and assigns authentication and accounting destination UDP port numbers.

This command adds the RADIUS server address and sets parameters to the RADIUS

server. The RADIUS server is added to the running configuration after you issue this

command. If parameters are not set using this command then common system

settings are applied.

Use the no variant of this command to remove the specified server host as a

RADIUS authentication and/or accounting server and set the destination port to

the default RADIUS server port number (1812).

Syntax radius-server host {<host-name>|<ip-address>} [acct-port

<0-65535>] [auth-port <0-65535>] [key <key-string>] [retransmit

<0-100>] [timeout <1-1000>]

no radius-server host {<host-name>|<ip-address>} [acct-port

<0-65535>] [auth-port <0-65535>]

Parameter Description

<host-name> Server host name. The DNS name of the RADIUS server host.

<ip-address> The IP address of the RADIUS server host.

acct-port Accounting port. Specifies the UDP destination port for RADIUS

accounting requests. If 0 is specified, the server is not used for

accounting. The default UDP port for accounting is 1813.

<0-65535>UDP port number

(Accounting port number is set to 1813 by default)

Specifies the UDP destination port for RADIUS accounting

requests. If 0 is specified, the host is not used for accounting.

auth-port Authentication port. Specifies the UDP destination port for

RADIUS authentication requests. If 0 is specified, the server is not

used for authentication. The default UDP port for authentication

is 1812.

<0-65535>UDP port number

(Authentication port number is set to 1812 by default)

Specifies the UDP destination port for RADIUS authentication

requests. If 0 is specified, the host is not used for authentication.

timeout Specifies the amount of time to wait for a response from the

server. If this parameter is not specified the global value

configured by the radius-server timeout command is used.

613-50137-01 Rev A Command Reference for FS980M Series 1107

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

RADIUS-SERVER HOST

Default The RADIUS client address is not configured (null) by default. No RADIUS server is

configured.

Mode Global Configuration

Usage Multiple radius -server host commands can be used to specify multiple hosts. The

software searches for hosts in the order they are specified. If no host-specific

timeout, retransmit, or key values are specified, the global values apply to that

host. If there are multiple RADIUS servers for this client, use this command multiple

times—once to specify each server.

If you specify a host without specifying the auth port or the acct port, it will by

default be configured for both authentication and accounting, using the default

UDP ports. To set a host to be a RADIUS server for authentication requests only, set

the acct-port parameter to 0; to set the host to be a RADIUS server for accounting

requests only, set the auth-port parameter to 0.

A RADIUS server is identified by IP address, authentication port and accounting

port. A single host can be configured multiple times with different authentication

or accounting ports. All the RADIUS servers configured with this command are

<1-1000>Time in seconds to wait for a server reply

(timeout is set to 5 seconds by default)

The time interval (in seconds) to wait for the RADIUS server to

reply before retransmitting a request or considering the server

dead. This setting overrides the global value set by the radius-

server timeout command.

If no timeout value is specified for this server, the global value is

used.

retransmit Specifies the number of retries before skip to the next server. If

this parameter is not specified the global value configured by the

radius-server retransmit command is used.

<0-100>Maximum number of retries

(maximum number of retries is set to 3 by default)

The maximum number of times to resend a RADIUS request to

the server, if it does not respond within the timeout interval,

before considering it dead and skipping to the next RADIUS

server. This setting overrides the global setting of the radius-

server retransmit command.

If no retransmit value is specified, the global value is used.

key Set shared secret key with RADIUS servers

<key-string> Shared key string applied

Specifies the shared secret authentication or encryption key for

all RADIUS communications between this device and the RADIUS

server. This key must match the encryption used on the RADIUS

daemon. All leading spaces are ignored, but spaces within and at

the end of the string are used. If spaces are used in the string, do

not enclose the string in quotation marks unless the quotation

marks themselves are part of the key. This setting overrides the

global setting of the radius-server key c ommand. If no key

value is specified, the global value is used.

Parameter Description

613-50137-01 Rev A Command Reference for FS980M Series 1108

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

RADIUS-SERVER HOST

included in the predefined RADIUS server group radius, which may be used by AAA

authentication, authorization and accounting commands. The client transmits

(and retransmits, according to the retransmit and timeout parameters) RADIUS

authentication or accounting requests to the servers in the order you specify them,

until it gets a response.

Examples To add the RADIUS server 10.0.0.20, use the following commands:

awplus# configure terminal

awplus(config)# radius-server host 10.0.0.20

To set the secret key to allied on the RADIUS server 10.0.0.20, use the following

commands:

awplus# configure terminal

awplus(config)# radius-server host 10.0.0.20 key allied

To delete the RADIUS server 10.0.0.20, use the following commands:

awplus# configure terminal

awplus(config)# no radius-server host 10.0.0.20

To configure rad1.company.com for authentication only, use the following

commands:

awplus# configure terminal

awplus(config)# radius-server host rad1.company.com acct-port 0

To remove the RADIUS server rad1.company.com configured for

authentication only, use the following commands:

awplus# configure terminal

awplus(config)# no radius-server host rad1.company.com

acct-port 0

To configure rad2.company.com for accounting only, use the following

commands:

awplus# configure terminal

awplus(config)# radius-server host rad2.company.com auth-port 0

To configure 192.168.1.1 with authentication port 1000, accounting port 1001 and

retransmit count 5, use the following commands:

awplus# configure terminal

awplus(config)# radius-server host 192.168.1.1 auth-port 1000

acct-port 1001 retransmit 5

Commands

aaa group server

radius-server key

radius-server retransmit

radius-server timeout

show radius statistics

613-50137-01 Rev A Command Reference for FS980M Series 1109

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

RADIUS-SERVER KEY

radius-server key

Overview This command sets a global secret key for RADIUS authentication on the device.

The shared secret text string is used for RADIUS authentication between the device

and a RADIUS server.

Note that if no secret key is explicitly specified for a RADIUS server, the global

secret key will be used for the shared secret for the server.

Use the no variant of this command to reset the secret key to the default (null).

Syntax radius-server key <key>

no radius-server key

Default The RADIUS server secret key on the system is not set by default (null).

Mode Global Configuration

Usage Use this command to set the global secret key shared between this client and its

RADIUS servers. If no secret key is specified for a particular RADIUS server using the

radius-server host c ommand, this global key is used.

After enabling AAA authentication with the aaa authentication login command,

set the authentication and encryption key using the radius-server key command

so the key entered matches the key used on the RADIUS server.

Examples To set the global secret key to allied for RADIUS server, use the following

commands:

awplus# configure terminal

awplus(config)# radius-server key allied

To set the global secret key to secret for RADIUS server, use the following

commands:

awplus# configure terminal

awplus(config)# radius-server key secret

To delete the global secret key for RADIUS server, use the following commands:

awplus# configure terminal

awplus(config)# no radius-server key

Commands

radius-server host

show radius statistics

Parameter Description

<key>Shared secret among radius server and 802.1X client.

613-50137-01 Rev A Command Reference for FS980M Series 1110

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

RADIUS-SERVER RETRANSMIT

radius-server retransmit

Overview This command sets the retransmit counter to use RADIUS authentication on the

device. This command specifies how many times the device transmits each

RADIUS request to the RADIUS server before giving up.

This command configures the retransmit parameter for RADIUS servers globally.

If the retransmit parameter is not specified for a RADIUS server by the

radius-server host command then the global configuration set by this command

is used for the server instead.

Use the no variant of this command to reset the re-transmit counter to the default

(3).

Syntax radius-server retransmit <retries>

no radius-server retransmit

Default The default RADIUS retransmit count on the device is 3.

Mode Global Configuration

Examples To set the RADIUS retransmit count to 1, use the following commands:

awplus# configure terminal

awplus(config)# radius-server retransmit 1

To set the RADIUS retransmit count to the default (3), use the following

commands:

awplus# configure terminal

awplus(config)# no radius-server retransmit

To configure the RADIUS retransmit count globally with 5, use the following

commands:

awplus# configure terminal

awplus(config)# radius-server retransmit 5

To disable retransmission of requests to a RADIUS server, use the following

commands:

awplus# configure terminal

awplus(config)# radius-server retransmit 0

Parameter Description

<retries> RADIUS server retries in the range <0-100>.

The number of times a request is resent to a RADIUS server that

does not respond, before the server is considered dead and the

next server is tried. If no retransmit value is specified for a

particular RADIUS server using the radius-server host

command, this global value is used.

613-50137-01 Rev A Command Reference for FS980M Series 1111

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

RADIUS-SERVER RETRANSMIT

Commands

radius-server deadtime

radius-server host

show radius statistics

613-50137-01 Rev A Command Reference for FS980M Series 1112

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

RADIUS-SERVER TIMEOUT

radius-server timeout

Overview Use this command to specify the RADIUS global timeout value. This is how long the

device waits for a reply to a RADIUS request before retransmitting the request, or

considering the server to be dead. If no timeout is specified for the particular

RADIUS server by the radius-server host command, it uses this global timeout

value.

Note that this command configures the timeout parameter for RADIUS servers

globally.

The no variant of this command resets the transmit timeout to the default (5

seconds).

Syntax radius-server timeout <seconds>

no radius-server timeout

Default The default RADIUS transmit timeout on the system is 5 seconds.

Mode Global Configuration

Examples To globally set the device to wait 20 seconds before retransmitting a RADIUS

request to unresponsive RADIUS servers, use the following commands:

awplus# configure terminal

awplus(config)# radius-server timeout 20

To set the RADIUS timeout parameter to 1 second, use the following commands:

awplus# configure terminal

awplus(config)# radius-server timeout 1

To set the RADIUS timeout parameter to the default (5 seconds), use the following

commands:

awplus# configure terminal

awplus(config)# no radius-server timeout

To configure the RADIUS server timeout period globally with 3 seconds, use the

following commands:

awplus# configure terminal

awplus(config)# radius-server timeout 3

Parameter Description

<seconds> RADIUS server timeout in seconds in the range 1 to 1000.

The global time in seconds to wait for a RADIUS server to reply to

a request before retransmitting the request, or considering the

server to be dead (depending on the radius-server retransmit

command).

613-50137-01 Rev A Command Reference for FS980M Series 1113

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

RADIUS-SERVER TIMEOUT

To reset the global timeout period for RADIUS servers to the default, use the

following command:

awplus# configure terminal

awplus(config)# no radius-server timeout

Commands

radius-server deadtime

radius-server host

radius-server retransmit

show radius statistics

613-50137-01 Rev A Command Reference for FS980M Series 1114

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

SERVER (SERVER GROUP)

server (Server Group)

Overview This command adds a RADIUS server to a server group in Server-Group

Configuration mode. The RADIUS server should be configured by the radius-server

host command.

The server is appended to the server list of the group and the order of

configuration determines the precedence of servers. If the server exists in the

server group already, it will be removed before added as a new server.

The server is identified by IP address and authentication and accounting UDP port

numbers. So a RADIUS server can have multiple entries in a group with different

authentication and/or accounting UDP ports. The auth-port specifies the UDP

destination port for authentication requests to the server. To disable

authentication for the server, set auth-port to 0. If the authentication port is

missing, the default port number is 1812. The acct-port specifies the UDP

destination port for accounting requests to the server. To disable accounting for

the server, set acct-port to 0. If the accounting port is missing, the default port

number is 1812.

Use the no variant of this command to remove a RADIUS server from the server

group.

Syntax server {<hostname>|<ip-address>} [auth-port

<0-65535>][acct-port <0-65535>]

no server {<hostname>|<ip-address>} [auth-port

<0-65535>][acct-port <0-65535>]

Parameter Description

<hostname> Server host name

<ip-address> Server IP address

The server is identified by IP address, authentication and

accounting UDP port numbers. So a RADIUS server can have

multiple entries in a group with different authentication and/or

accounting UDP ports.

auth-port Authentication port

The auth-port specifies the UDP destination port for

authentication requests to the server. To disable authentication

for the server, set auth-port to 0. If the authentication port is

missing, the default port number is 1812.

<0-65535>UDP port number (default: 1812)

acct-port Accounting port

The acct-port specifies the UDP destination port for accounting

requests to the server. To disable accounting for the server, set

acct-port to 0. If the accounting port is missing, the default port

number is 1813.

<0-65535>UDP port number (default: 1813)

613-50137-01 Rev A Command Reference for FS980M Series 1115

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

SERVER (SERVER GROUP)

Default The default Authentication port number is 1812 and the default Accounting port

number is 1813.

Mode Server Group Configuration

Usage The RADIUS server to be added must be configured by the radius-server host

command. In order to add or remove a server, the auth-port and acct-port

parameters in this command must be the same as the corresponding parameters

in the radius-server host command.

Examples To create a RADIUS server group RAD_AUTH1 for authentication, use the following

commands:

awplus# configure terminal

awplus(config)# aaa group server radius RAD_AUTH1

awplus(config-sg)# server 192.168.1.1 acct-port 0

awplus(config-sg)# server 192.168.2.1 auth-port 1000 acct-port

To create a RADIUS server group RAD_ACCT1 for accounting, use the following

commands:

awplus# configure terminal

awplus(config)# aaa group server radius RAD_ACCT1

awplus(config-sg)# server 192.168.2.1 auth-port 0 acct-port

1001

awplus(config-sg)# server 192.168.3.1 auth-port 0

To remove server 192.168.3.1 from the existing server group GROUP1, use the

following commands:

awplus# configure terminal

awplus(config)# aaa group server radius GROUP1

awplus(config-sg)# no server 192.168.3.1

Commands

aaa accounting auth-mac

aaa accounting auth-web

aaa accounting dot1x

aaa accounting login

aaa authentication auth-mac

aaa authentication auth-web

aaa authentication login

aaa group server

radius-server host

613-50137-01 Rev A Command Reference for FS980M Series 1116

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

SHOW DEBUGGING RADIUS

show debugging radius

Overview This command displays the current debugging status for the RADIUS servers.

Syntax show debugging radius

Mode User Exec and Privileged Exec

Example To display the current debugging status of RADIUS servers, use the command:

awplus# show debugging radius

Output Figure 31-1: Example output from the show debugging radius command

RADIUS debugging status:

RADIUS event debugging is off 

RADIUS packet debugging is off

613-50137-01 Rev A Command Reference for FS980M Series 1117

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

SHOW RADIUS

show radius

Overview This command displays the current RADIUS server configuration and status.

Syntax show radius

Mode User Exec and Privileged Exec

Example To display the current status of RADIUS servers, use the command:

awplus# show radius

Output Figure 31-2: Example output from the show radius command showing RADIUS

servers

Example See the sample output below showing RADIUS client status and RADIUS

configuration:

awplus# show radius

RADIUS Global Configuration

Source Interface : not configured

Secret Key : secret

Timeout : 5 sec

Retransmit Count : 3

Deadtime : 20 min

Server Host : 192.168.1.10

Authentication Port : 1812

Accounting Port : 1813

Secret Key : secret

Timeout : 3 sec

Retransmit Count : 2

Server Host : 192.168.1.11

Authentication Port : 1812

Accounting Port : not configured



Server Name/ Auth Acct Auth Acct

IP Address Port Port Status Status

------------------------------------------------------------

192.168.1.10 1812 1813 Alive Alive

192.168.1.11 1812 N/A Alive N/A

613-50137-01 Rev A Command Reference for FS980M Series 1118

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

SHOW RADIUS

Output Figure 31-3: Example output from the show radius command showing RADIUS

client status

RADIUS global interface name: awplus

Secret key:

Timeout: 5

Retransmit count: 3

Deadtime: 0



Server Address: 150.87.18.89

Auth destination port: 1812

Accounting port: 1813

Secret key: swg

Timeout: 5

Retransmit count: 3

Deadtime: 0show radius local-server group

Output Parameter Meaning

Source

Interface

The interface name or IP address to be used for the source

address of all outgoing RADIUS packets.

Secret Key A shared secret key to a radius server.

Timeout A time interval in seconds.

Retransmit

Count

The number of retry count if a RADIUS server does not

response.

Deadtime A time interval in minutes to mark a RADIUS server as “dead”.

Interim-Update A time interval in minutes to send Interim-Update Accounting

report.

Group Deadtime The deadtime configured for RADIUS servers within a server

group.

Server Host The RADIUS server hostname or IP address.

Authentication

Port

The destination UDP port for RADIUS authentication requests.

Accounting Port The destination UDP port for RADIUS accounting requests.

613-50137-01 Rev A Command Reference for FS980M Series 1119

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

SHOW RADIUS

Auth Status The status of the authentication port.

The status (“dead”, “error”, or “alive”) of the RADIUS authentica

tion server and, if dead, how long it has been dead for.

Alive The server is alive.

Error The server is not responding.

Dead The server is detected as dead and it will not be

used for deadtime period. The time displayed in

the output shows the server is in dead status for

that amount of time.

Unknown The server is never used or the status is unknown.

Acct Status The status of the accounting port.

The status (“dead”, “error”, or “alive”) of the RADIUS accounting

server and, if dead, how long it has been dead for.

Output Parameter Meaning

613-50137-01 Rev A Command Reference for FS980M Series 1120

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

SHOW RADIUS STATISTICS

show radius statistics

Overview This command shows the RADIUS client statistics for the device.

Syntax show radius statistics

Mode User Exec and Privileged Exec

Example See the sample output below showing RADIUS client statistics and RADIUS

configuration:

awplus# show radius statistics

Output Figure 31-4: Example output from the show radius statistics command:

RADIUS statistics for Server: 150.87.18.89

Access-Request Tx : 5 - Retransmit : 0

Access-Accept Rx : 1 - Access-Reject Rx : 2

Access-Challenge Rx : 2

Unknown Type : 0 - Bad Authenticator : 0

Malformed Access-Resp : 0 - Wrong Identifier : 0

Bad Attribute : 0 - Packet Dropped : 0

TimeOut : 0 - Dead count : 0

Pending Request : 0

613-50137-01 Rev A Command Reference for FS980M Series 1121

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

RADIUS COMMANDS

UNDEBUG RADIUS

undebug radius

Overview This command applies the functionality of the no debug radius command.

613-50137-01 Rev A Command Reference for FS980M Series 1122

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

Public Key

Infrastructure

Commands

Introduction

Overview This chapter provides an alphabetical reference of commands used to configure

the Public Key Infrastructure (PKI) capabilities on an AlliedWare Plus device.

Command List •“crypto key generate rsa” on page 1123

•“crypto key zeroize” on page 1124

•“crypto pki authenticate” on page 1125

•“crypto pki enroll” on page 1126

•“crypto pki enroll user” on page 1127

•“crypto pki export pem” on page 1129

•“crypto pki export pkcs12” on page 1130

•“crypto pki import pem” on page 1132

•“crypto pki import pkcs12” on page 1134

•“crypto pki trustpoint” on page 1135

•“enrollment (trustpoint configuration mode)” on page 1136

•“fingerprint (trustpoint configuration mode)” on page 1137

•“no crypto pki certificate” on page 1139

•“rsakeypair (trustpoint configuration mode)” on page 1140

•“show crypto key mypubkey rsa” on page 1141

•“show crypto pki certificates” on page 1142

•“show crypto pki enrollment user” on page 1144

•“show crypto pki trustpoint” on page 1145

•“subject-name (trustpoint configuration)” on page 1146

613-50137-01 Rev A Command Reference for FS980M Series 1123

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

CRYPTO KEY GENERATE RSA

crypto key generate rsa

Overview Use this command to generate a cryptographic public/private key pair for the

Rivest-Shamir-Adleman (RSA) encryption algorithm.

Syntax crypto key generate rsa [label <keylabel>] [<1024-4096>]

Mode Privileged Exec

Usage The generated key may be used for multiple server certificates in the system. A key

is referenced by its label. A bit length between 1024 and 4096 bits may be

specified. Larger bit lengths are more secure, but require more computation time.

The specified key must not already exist.

Example To create a key with the label "example-server-key" and a bit length of 2048, use

the commands:

awplus> enable

awplus# crypto key generate rsa label example-server-key 2048

Commands

crypto key zeroize

rsakeypair (trustpoint configuration mode)

show crypto key mypubkey rsa

Parameter Description

<keylabel> The name of the key to be created. The name must start with an

alphanumeric character, and may only contain alphanumeric

characters, underscores, dashes, or periods. The maximum length

of the name is 63 characters. If no label is specified the default

value “server-default” is used.

<1024-4096> The bit length for the key. If no bit length is specified the default

of 2048 is used.

613-50137-01 Rev A Command Reference for FS980M Series 1124

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

CRYPTO KEY ZEROIZE

crypto key zeroize

Overview Use this command to delete one or all cryptographic public/private key pairs.

Syntax crypto key zeroize rsa <keylabel>

crypto key zeroize all

Mode Privileged Exec

Usage Note that this command has the same effect as using the delete command (it

deletes the file from Flash memory but does not overwrite it with zeros).

The specified key must exist but must not be in use for any existing server

certificates.

A key may not be deleted if it is associated with the server certificate or server

certificate signing request for an existing trustpoint. To remove a server certificate

so that the key may be deleted, use the no crypto pki enroll command to

de-enroll the server.

Example To delete an RSA key named "example-server-key", use the following command:

awplus# crypto key zeroize rsa example-server-key

Commands

crypto key generate rsa

show crypto key mypubkey rsa

Parameter Description

rsa <keylabel> Delete a single key pair for the Rivest-Shamir-Adleman (RSA)

encryption algorithm.

all Delete all keys.

613-50137-01 Rev A Command Reference for FS980M Series 1125

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

CRYPTO PKI AUTHENTICATE

crypto pki authenticate

Overview Use this command to authenticate a trustpoint by generating or importing the

root CA certificate. This must be done before the server can be enrolled to the

trustpoint.

Syntax crypto pki authenticate <trustpoint>

Mode Privileged Exec

Usage If the trustpoint’s enrollment setting is “selfsigned”, then this command causes a

private key to be generated for the root CA, and a self-signed certificate to be

generated based on that key.

If the trustpoint’s enrollment setting is “terminal”, then this command prompts

the user to paste a certificate Privacy Enhanced Mail (PEM) file at the CLI terminal.

If the certificate is a valid selfsigned CA certificate, then it will be stored as the

trustpoint’s root CA certificate.

The specified trustpoint must already exist, and its enrollment mode must have

been defined.

Example To show the enrollment setting of a trustpoint named “example” and then

generate a certificate from it, use the commands:

awplus> enable

awplus# configure terminal

awplus(config)# crypto pki trustpoint example

awplus(ca-trustpoint)# enrollment selfsigned

awplus(config)# exit

awplus# exit

awplus# crypto pki authenticate example

Commands

crypto pki import pem

crypto pki trustpoint

enrollment (trustpoint configuration mode)

Parameter Description

<trustpoint> The name of the trustpoint to be authenticated.

613-50137-01 Rev A Command Reference for FS980M Series 1126

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

CRYPTO PKI ENROLL

crypto pki enroll

Overview Use this command to enroll the local server to the specified trustpoint.

Use the no variant of this command to de-enroll the server by removing its

certificate

Syntax crypto pki enroll <trustpoint>

no crypto pki enroll <trustpoint>

Mode Privileged Exec

Usage For the local server, “enrollment” is the process of creating of a certificate for the

server that has been signed by a CA associated with the trustpoint. The public

portion of the RSA key pair specified using the rsakeypair parameter for the

trustpoint will be included in the server certificate.

If the trustpoint represents a locally self-signed certificate authority, then this

command results in the direct generation of the server certificate, signed by the

root CA for the trustpoint.

If the trustpoint represents an external certificate authority, then this command

results in the generation of a Certificate Signing Request (CSR) file, which is

displayed at the terminal in Privacy-Enhanced Mail (PEM) format, suitable for

copying and pasting into a file or message. The CSR must be sent to the external

CA for processing. When the CA replies with the signed certificate, that certificate

should be imported using the crypto pki import pem command, to complete the

enrollment process.

The specified trustpoint must already exist, and it must already be authenticated.

Example To enroll the local server with the trustpoint “example”, use the following

commands:

awplus> enable

awplus# crypto pki enroll example

Commands

crypto pki enroll user

crypto pki import pem

crypto pki trustpoint

enrollment (trustpoint configuration mode)

Parameter Description

<trustpoint> The name of the trustpoint to be enrolled

613-50137-01 Rev A Command Reference for FS980M Series 1127

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

CRYPTO PKI ENROLL USER

crypto pki enroll user

Overview Use this command to enroll a single RADIUS user or all RADIUS users to the

specified trustpoint.

Use the no variant of this command to remove the PKCS#12 file from the system.

Note that the PKCS#12 files are generated in a temporary (volatile) file system, so a

system restart also results in removal of all of the files.

Syntax crypto pki enroll <trustpoint> 

{user <username>|local-radius-all-users}

no crypto pki enroll <trustpoint> 

{user <username>|local-radius-all-users}

Mode Privileged Exec

Usage For RADIUS users, “enrollment” is the process of generating a private key and a

corresponding client certificate for each user, with the certificate signed by the

root CA for the trustpoint. The resulting certificates may be exported to client

devices, for use with PEAP or EAP-TLS authentication with the local RADIUS server.

The specified trustpoint must represent a locally self-signed certificate authority.

The private key and certificate are packaged into a PKCS#12-formatted file,

suitable for export using the crypto pki export pkcs12 command. The private key

is encrypted for security, with a passphrase that is entered at the command line.

The passphrase is required when the PKCS#12 file is imported on the client system.

The passphrase is not stored anywhere on the device, so users are responsible for

remembering it until the export-import process is complete.

If local-radius-all-users is specified instead of an individual user, then keys and

certificates for all RADIUS users will be generated at once. All the keys will be

encrypted using the same passphrase.

The specified trustpoint must already exist, it must represent a locally self-signed

CA, and it must already have been authenticated.

Example To enroll the user “example-user” with the trustpoint “example”, use the following

commands:

awplus> enable

awplus# crypto pki enroll example user example-user

Parameter Description

<trustpoint> The name of the trustpoint to which users are to be enrolled.

<username> The name of the user to enroll to the trustpoint.

613-50137-01 Rev A Command Reference for FS980M Series 1128

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

CRYPTO PKI ENROLL USER

To enroll all local RADIUS users with the trustpoint “example”, use the following

commands:

awplus> enable

awplus# crypto pki enroll example local-radius-all-users

Commands

crypto pki export pkcs12

crypto pki trustpoint

613-50137-01 Rev A Command Reference for FS980M Series 1129

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

CRYPTO PKI EXPORT PEM

crypto pki export pem

Overview Use this command to export the root CA certificate for the given trustpoint to a file

in Privacy-Enhanced Mail (PEM) format. The file may be transferred to the specified

destination URL, or displayed at the terminal.

Syntax crypto pki export <trustpoint> pem [terminal|<url>]

Default The PEM will be displayed to the terminal by default.

Mode Privileged Exec

Usage The specified trustpoint must already exist, and it must already be authenticated.

Example To display the PEM file for the trustpoint “example” to the terminal, use the

following commands:

awplus> enable

awplus# crypto pki export example pem terminal

To export the PEM file “example.pem” for the trustpoint “example” to the URL

“tftp://server_a/”, use the following commands:

awplus> enable

awplus# crypto pki export example pem

tftp://server_a/example.pem

Commands

crypto pki authenticate

crypto pki import pem

crypto pki trustpoint

Parameter Description

<trustpoint> The name of the trustpoint for which the root CA certificate is

tobe exported.

terminal Display the PEM file to the terminal.

<url> Transfer the PEM file to the specified URL.

613-50137-01 Rev A Command Reference for FS980M Series 1130

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

CRYPTO PKI EXPORT PKCS12

crypto pki export pkcs12

Overview Use this command to export a certificate and private key for an entity in a

trustpoint to a file in PKCS#12 format at the specified URL. The private key is

encrypted with a passphrase for security.

Syntax crypto pki export <trustpoint> pkcs12 {ca|server|<username>}

<url>

Mode Privileged Exec

Usage If the ca option is specified, this command exports the root CA certificate and the

corresponding private key, if the trustpoint has been authenticated as a locally

selfsigned CA. (If the trustpoint represents an external CA, then there is no private

key on the system corresponding to the root CA certificate. Use the crypto pki

export pem file to export the certificate by itself.) The command prompts for a

passphrase to encrypt the private key.

If the server option is specified, this command exports the server certificate and

the corresponding private key, if the server has been enrolled to the trustpoint. The

command prompts for a passphrase to encrypt the private key.

If a RADIUS username is specified, this command exports the PKCS#12 file that was

generated using the crypto pki enroll user command. (The key within the file was

already encrypted as part of the user enrollment process.)

In the event that there is a RADIUS user named “ca” or “server”, enter “user:ca” or

“user:server” as the username.

The key and certificate must already exist.

Parameter Description

<trustpoint> The name of the trustpoint for which the certificate and key are

tobe exported.

ca If this option is specified, the command exports the root CA

certificate and corresponding key.

server If this option is specified, the command exports the server

certificate and corresponding key.

<username> If a RADIUS username is specified, the command exports the

PKCS#12 file that was previously generated using the crypto pki

enroll user command. To avoid ambiguity with keywords, the

username may be prefixed by the string “user:”.

<url> The destination URL for the PKCS#12 file. The format of the URLis

the same as any valid destination for a file copy command.

613-50137-01 Rev A Command Reference for FS980M Series 1131

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

CRYPTO PKI EXPORT PKCS12

Example To export the PKCS#12 file “example.pk12” for the trustpoint “example” to the URL

“tftp://backup/”, use the following commands:

awplus> enable

awplus# crypto pki export example pkcs12 ca

tftp://backup/example.pk12

Commands

crypto pki enroll user

crypto pki export pem

crypto pki import pkcs12

613-50137-01 Rev A Command Reference for FS980M Series 1132

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

CRYPTO PKI IMPORT PEM

crypto pki import pem

Overview This command imports a certificate for the given trustpoint from a file in

Privacy-Enhanced Mail (PEM) format. The file may be transferred from the specified

destination URL, or entered at the terminal.

Syntax crypto pki import <trustpoint> pem [terminal|<url>]

Default The PEM will be imported from the terminal by default.

Mode Privileged Exec

Usage The command is generally used for trustpoints representing external certificate

authorities. It accepts root CA certificates, intermediate CA certificates, and server

certificates. The system automatically detects the certificate type upon import.

Using this command to import root CA certificates at the terminal is identical to the

functionality provided by the crypto pki authenticate command, for external

certificate authorities. The imported certificate is validated to ensure it is a proper

CA certificate.

Intermediate CA certificates are validated to ensure they are proper CA certificates,

and that the issuer chain ends in a root CA certificate already installed for the

trustpoint. If there is no root CA certificate for the trustpoint (i.e., if the trustpoint is

unauthenticated) then intermediate CA certificates may not be imported.

Server certificates are validated to ensure that the issuer chain ends in a root CA

certificate already installed for the trustpoint. If there is no root CA certificate for

the trustpoint (i.e., if the trustpoint is unauthenticated) then server certificates may

not be imported.

The specified trustpoint must already exist. If the imported certificate is

self-signed, then no certificates may exist for the trustpoint. Otherwise, the issuer’s

certificate must already be present for the trustpoint.

Example To import the PEM file for the trustpoint “example” from the terminal, use the

following commands:

awplus> enable

awplus# crypto pki import example pem

Parameter Description

<trustpoint> The name of the trustpoint for which the root CA certificate is to

be imported.

terminal Optional parameter, If specified, the command prompts the user

to enter (or paste) the PEM file at the terminal. If parameter is

specified terminal is assumed by default.

<url> Optional parameter, If specified, the PEM file is transferred from

the specified URL

613-50137-01 Rev A Command Reference for FS980M Series 1133

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

CRYPTO PKI IMPORT PEM

To import the PEM file for the trustpoint “example” from the URL “tftp://server_a/”,

use the following commands:

awplus> enable

awplus# crypto pki import example pem

tftp://server_a/example.pem

Commands

crypto pki authenticate

crypto pki export pem

crypto pki trustpoint

613-50137-01 Rev A Command Reference for FS980M Series 1134

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

CRYPTO PKI IMPORT PKCS12

crypto pki import pkcs12

Overview This command imports a certificate and private key for an entity in a trustpoint

from a file in PKCS#12 format at the specified URL. The command prompts for a

passphrase to decrypt the private key within the file.

Syntax crypto pki import <trustpoint> pkcs12 {ca|server} <url>

Mode Privileged Exec

Usage If the ca option is specified, this command imports the root CA certificate and the

corresponding private key. This is only valid if the root CA certificate does not

already exist for the trustpoint (i.e., if the trustpoint is unauthenticated).

If the server option is specified, this command imports the server certificate and

the corresponding private key. The imported private key is given a new unique

label of the form “localN”, where N is a non-negative integer. This operation is only

valid if the server certificate does not already exist for the trustpoint (i.e., if the

server is not enrolled to the trustpoint).

PKCS#12 files for RADIUS users may not be imported with this command. (There is

no value in doing so, as the files are not needed on the local system.)

The specified trustpoint must already exist. The key and certificate must not

already exist.

Example To import the PKCS#12 file “example.pk12” for the trustpoint “example” to the URL

“tftp://backup/”, use the following commands:

awplus> enable

awplus# crypto pki import example pkcs12 ca

tftp://backup/example.pk12

Commands

crypto pki export pkcs12

crypto pki import pem

Parameter Description

<trustpoint> The name of the trustpoint for which the certificate and key are to

be imported.

ca If this option is specified, the command imports the root CA

certificate and corresponding key.

server If this option is specified, the command imports the server

certificate and corresponding key.

<url> The source URL for the PKCS#12 file. The format of the URLis the

same as any valid destination for a file copy command.

613-50137-01 Rev A Command Reference for FS980M Series 1135

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

CRYPTO PKI TRUSTPOINT

crypto pki trustpoint

Overview Use this command to declare the named trustpoint and enter trustpoint

configuration mode.

Use the no variant of this command to destroy the trustpoint.

Syntax crypto pki trustpoint <trustpoint>

no crypto pki trustpoint <trustpoint>

Mode Global Configuration

Usage If the trustpoint did not previously exist, it is created as a new trustpoint. The

trustpoint will be empty (unauthenticated) unless the name “local” is selected, in

which case the system will automatically authenticate the trustpoint as a local

self-signed certificate authority.

The no variant of this command destroys the trustpoint by removing all CA and

server certificates associated with the trustpoint, as well as the private key

associated with the root certificate (if the root certificate was locally self-signed).

This is a destructive and irreversible operation, so this command should be used

with caution.

Example To configure a trustpoint named “example”, use the following commands:

awplus> enable

awplus# configure terminal

awplus(config)# crypto pki trustpoint example

Commands

show crypto pki certificates

show crypto pki trustpoint

Parameter Description

<trustpoint> The name of the trustpoint. The name must start with an

alphanumeric character, and may only contain alphanumeric

characters, underscores, dashes, or periods. The maximum length

of the name is 63 characters.

613-50137-01 Rev A Command Reference for FS980M Series 1136

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

ENROLLMENT (TRUSTPOINT CONFIGURATION MODE)

enrollment (trustpoint configuration mode)

Overview Use this command to declare how certificates will be added to the system for the

current trustpoint.

Syntax enrollment {selfsigned|terminal}

Mode Trustpoint Configuration

Usage If the enrollment is set to selfsigned, then the system will generate a root CA

certificate and its associated key when the crypto pki authenticate command is

issued. It will generate a server certificate (signed by the root CA certificate) when

the crypto pki enroll command is issued.

If the enrollment is set to terminal, then the system will prompt the user to paste

the root CA certificate Privacy Enhanced Mail (PEM) file at the terminal, when the

crypto pki authenticate command is issued. It will create a Certificate Signing

Request (CSR) file for the local server when the crypto pki enroll command is

issued. The server certificate received from the external CA should be imported

using the crypto pki import pem command.

The trustpoint named “local” may only use the selfsigned enrollment setting.

If no enrollment mode is specified, the crypto pki authenticate command will fail

for the trustpoint.

Example To configure the trustpoint named "example" and set its enrollment to selfsigned,

use the following commands:

awplus> enable

awplus# configure terminal

awplus(config)# crypto pki trustpoint example

awplus(ca-trustpoint)# enrollment selfsigned

Commands

crypto pki enroll

Parameter Description

selfsigned Sets the enrollment mode for the current trustpoint to selfsigned.

terminal Sets the enrollment mode for the current trustpoint to terminal.

613-50137-01 Rev A Command Reference for FS980M Series 1137

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

FINGERPRINT (TRUSTPOINT CONFIGURATION MODE)

fingerprint (trustpoint configuration mode)

Overview Use this command to declare that certificates with the specified fingerprint should

be automatically accepted, when importing certificates from an external certificate

authority. This can affect the behavior of the crypto pki authenticate and crypto

pki import pem commands.

Use the no variant of this command to remove the specified fingerprint from the

pre-accepted list.

Syntax fingerprint <word>

no fingerprint <word>

Default By default, no fingerprints are pre-accepted for the trustpoint.

Mode Trustpoint Configuration

Usage Specifying a fingerprint adds it to a list of pre-accepted fingerprints for the

trustpoint. When a certificate is imported, if it matches any of the pre-accepted

values, then it will be saved in the system automatically. If the imported

certificate’s fingerprint does not match any pre-accepted value, then the user will

be prompted to verify the certificate contents and fingerprint visually.

This command is useful when certificates from an external certificate authority are

being transmitted over an insecure channel. If the certificate fingerprint is

delivered via a separate messaging channel, then pre-entering the fingerprint

value via cut-and-paste may be less errorprone than attempting to verify the

fingerprint value visually.

The fingerprint is a series of 40 hexadecimal characters. It may be entered as a

continuous string, or as a series of up to multiple strings separated by spaces. The

input format is flexible because different certificate authorities may provide the

fingerprint string in different formats.

Example To configure a fingerprint “5A81D34C 759CC4DA CFCA9F65 0303AD83 410B03AF”

for the trustpoint named “example”, use the following commands:

awplus> enable

awplus# configure terminal

awplus(config)# crypto pki trustpoint example

awplus(ca-trustpoint)# fingerprint 5A81D34C 759CC4DA CFCA9F65

0303AD83 410B03AF

Commands

crypto pki authenticate

Parameter Description

<word> The fingerprint as a series of 40 hexadecimal characters,

optionally separated into multiple character strings.

613-50137-01 Rev A Command Reference for FS980M Series 1138

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

FINGERPRINT (TRUSTPOINT CONFIGURATION MODE)

crypto pki import pem

613-50137-01 Rev A Command Reference for FS980M Series 1139

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

NO CRYPTO PKI CERTIFICATE

no crypto pki certificate

Overview Use this command to delete a certificate with the specified fingerprint from the

specified trustpoint.

Syntax no crypto pki certificate <trustpoint> <word>

Default By default, no fingerprints are pre-accepted for the trustpoint.

Mode Privileged Exec

Usage The fingerprint can be found in the output of the show crypto pki certificates

command. If there are dependent certificates in the trustpoint (i.e., if other

certificates were signed by the specified certificate), the command will be rejected.

If the specified certificate is the root CA certificate and the trustpoint represents a

locally selfsigned CA, then the corresponding private key is also deleted from the

system. Deleting the root CA certificate effectively resets the trustpoint to an

unauthenticated state.

Example To delete a certificate with the fingerprint "594EDEF9 C7C4308C 36D408E0

77E784F0 A59E8792" from the trustpoint “example”, use the following commands:

awplus> enable

awplus# no crypto pki certificate example 

594EDEF9 C7C4308C 36D408E0 77E784F0 A59E8792

Commands

no crypto pki trustpoint

show crypto pki certificates

Parameter Description

<trustpoint> The name of the trustpoint.

<word> The fingerprint as a series of 40 hexadecimal characters,

optionally separated into multiple character strings.

613-50137-01 Rev A Command Reference for FS980M Series 1140

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

RSAKEYPAIR (TRUSTPOINT CONFIGURATION MODE)

rsakeypair (trustpoint configuration mode)

Overview Use this command to declare which RSA key pair should be used to enroll the local

server with the trustpoint. Note that this defines the key pair used with the server

certificate, not the key pair used with the root CA certificate.

Use the no variant of this command to restore the default value, “server-default”.

Syntax rsakeypair <keylabel> [<1024-4096>]

no rsakeypair

Default The default value for keylabel is “server-default”.

The default value for the key bit length is 2048.

Mode Trustpoint Configuration

Usage If the label specified does not refer to an existing key created by the crypto key

generate rsa command, the key will be implicitly generated when the crypto pki

enroll command is issued to generate the server certificate or the server certificate

signing request. The optional numeric parameter defines the bit length for the key,

and is only applicable for keys that are implicitly created during enrollment.

This command does not affect server certificates or server certificate signing

requests that have already been generated. The trustpoint’s server certificate is set

to use whatever key pair was specified for the trustpoint at the time the crypto pki

enroll command is issued.

The default key pair is “server-default”. The default bit length is 2048 bits.

Example To configure trustpoint "example" to use the key pair "example-server-key" with a

bit length of 2048, use the following commands:

awplus> enable

awplus# configure terminal

awplus(config)# crypto pki trustpoint example

awplus(ca-trustpoint)# rsakeypair example-server-key 2048

Commands

crypto key generate rsa

Parameter Description

<keylabel> The key to be used with the server certificate for this trustpoint.

The name must start with an alphanumeric character, and may

only contain alphanumeric characters, underscores, dashes, or

periods. The maximum length of the name is 63 characters.

<1024-4096>The bit length for the key, to be used if the key is implicitly

generated during server enrollment.

613-50137-01 Rev A Command Reference for FS980M Series 1141

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

SHOW CRYPTO KEY MYPUBKEY RSA

show crypto key mypubkey rsa

Overview Use this command to display information about the specified

Rivest-Shamir-Adleman encryption key.

Syntax show crypto key mypubkey rsa [<keylabel>]

Default By default, all keys will be shown.

Mode Privileged Exec

Usage If no key label is specified, information about all keys is shown. The command

displays the bit length of the key, a key fingerprint (a hash of the key contents to

help uniquely identify a key), and a list of trustpoints in which the server certificate

is using the key.

The specified keys must exist.

Example To show all keys, use the following commands:

awplus> enable

awplus# show crypto key mypubkey rsa

Output Figure 32-1: Example output from show crypto key mypubkey rsa

Commands

crypto key generate rsa

Parameter Description

<keylabel> The name of the key to be shown, if specified.

awplus#show crypto key mypubkey rsa

--------------------

RSA Key Pair "example-server-key":

Key size : 2048 bits

Fingerprint : 1A605D73 C2274CB7 853886B3 1C802FC6 7CDE45FB

Trustpoints : example

--------------------

RSA Key Pair "server-default":

Key size : 2048 bits

Fingerprint : 34AC4D2D 5249A168 29D426A3 434FFC59 C4A19901

Trustpoints : local

613-50137-01 Rev A Command Reference for FS980M Series 1142

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

SHOW CRYPTO PKI CERTIFICATES

show crypto pki certificates

Overview Use this command to display information about existing certificates for the

specified trustpoint.

Syntax show crypto pki certificates [<trustpoint>]

Default By default, the certificates for all trustpoints are shown.

Mode Privileged Exec

Usage If no trustpoint is specified, certificates for all trustpoints are shown. The command

displays the certificates organized into certificate chains. It starts with the server

certificate and then displays its issuer, and continues up the issuer chain until the

root CA certificate is reached.

For each certificate, the command displays the certificate type, the subject’s

distinguished name (the entity identified by the certificate), the issuer’s

distinguished name (the entity that signed the certificate), the validity dates for the

certificate, and the fingerprint of the certificate. The fingerprint is a cryptographic

hash of the certificate contents that uniquely identifies the certificate.

The specified trustpoints must already exist.

Example To show the certificates for the trustpoint “example”, use the following command:

awplus> enable

awplus# show crypto pki certificates example

Parameter Description

<trustpoint> The trustpoint for which the certificates are to be shown.

613-50137-01 Rev A Command Reference for FS980M Series 1143

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

SHOW CRYPTO PKI CERTIFICATES

Output Figure 32-2: Example output from show crypto pki certificates

Commands

crypto pki trustpoint

awplus>enable

awplus#show crypto pki certificates example

--------------------

Trustpoint "example" Certificate Chain

--------------------

Server certificate

Subject : /O=local/CN=local.loc.lc

Issuer : /C=NZ/CN=local_Signing_CA

Valid From : Nov 11 15:35:21 2015 GMT

Valid To : Aug 31 15:35:21 2018 GMT

Fingerprint : 5A81D34C 759CC4DA CFCA9F65 0303AD83 410B03AF

Intermediate CA certificate

Subject : /C=NZ/CN=example_Signing_CA

Issuer : /C=NZ/CN=example_Root_CA

Valid From : Sep 3 18:45:01 2015 GMT

Valid To : Oct 10 18:45:01 2020 GMT

Fingerprint : AE2D5850 9867D258 ABBEE95E 2E0E3D81 60714920

Imported root certificate

Subject : /C=NZ/CN=example_Root_CA

Issuer : /C=NZ/CN=example_Root_CA

Valid From : Jul 23 18:12:10 2015 GMT

Valid To : May 12 18:12:10 2025 GMT

Fingerprint : 594EDEF9 C7C4308C 36D408E0 77E784F0 A59E8792

613-50137-01 Rev A Command Reference for FS980M Series 1144

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

SHOW CRYPTO PKI ENROLLMENT USER

show crypto pki enrollment user

Overview Use this command to display a list of trustpoints for which RADIUS user

enrollments have been performed, using the crypto pki enroll user command.

This indicates that PKCS#12 files for the user are available for export for the given

trustpoints, using the crypto pki export pkcs12 command.

Syntax crypto pki enrollment user <username>

Mode Privileged Exec

Example To show the list of trustpoints to which user “exampleuser1” is enrolled, use the

following commands:

awplus> enable

awplus(config)# show crypto pki enrollment user exampleuser1

Output Figure 32-3: Example output from show crypto pki enrollment user

Commands

crypto pki enroll user

crypto pki export pkcs12

Parameter Description

<username> The user for which enrollments are to be shown.

awplus> enable

awplus# show crypto pki enrollment user exampleuser1

User "exampleuser1" is enrolled to the following trustpoints:

local,example

613-50137-01 Rev A Command Reference for FS980M Series 1145

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

SHOW CRYPTO PKI TRUSTPOINT

show crypto pki trustpoint

Overview Use this command to display information about the specified trustpoint.

Syntax show crypto pki trustpoint [<trustpoint>]

Default By default, all trustpoints are shown.

Mode Privileged Exec

Usage If no trustpoint is specified, information about all trustpoints is shown. The

command displays the authentication status of the trustpoint, the fingerprint of

the root CA certificate (if it exists), the enrollment status of the local server with the

trustpoint, a list of any applications that are configured to use the trustpoint, and

the trustpoint parameters that were configured from trustpoint-configuration

mode.

The specified trustpoints must already exist.

Example To show the details of the trustpoint “example”, use the following commands:

awplus> enable

awplus# show crypto pki trustpoint example

Output Figure 32-4: Example output from show crypto pki trustpoint

Commands

crypto pki trustpoint

show crypto pki certificates

Parameter Description

<trustpoint> The name of the trustpoint to be shown

awplus> enable

awplus# show crypto pki trustpoint example

--------------------

Trustpoint "example"

Type : Self-signed certificate authority

Root Certificate: 50C1856B EEC7555A 0F3A61F6 690D9463 67DF74D1

Local Server : The server is enrolled to this trustpoint.

Server Key : example-server-key

Applications : RADIUS



Authentication and Enrollment Parameters:

Enrollment : selfsigned

RSA Key Pair : example-server-key (2048 bits)

--------------------

613-50137-01 Rev A Command Reference for FS980M Series 1146

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

SUBJECT-NAME (TRUSTPOINT CONFIGURATION)

subject-name (trustpoint configuration)

Overview Use this command to specify the distinguished name string that should be used for

the subject field in the server certificate, when enrolling the server (generating the

server certificate or server certificate signing request).

Syntax subject-name <word>

Default If no subject name is specified for the trustpoint, then the system automatically

builds a name of the form “/O=AlliedWare Plus/CN=xxxx.yyyy.zzz”, where “xxxx” is

the hostname of the system and “yyyy.zzz” is the default search domain for the

system.

Mode Trustpoint Configuration

Usage The subject name is specified as a variable number of fields, where each field

begins with a forward-slash character (“/”). Each field is of the form “XX=value”,

where “XX” is the abbreviation of the node type in the tree.

Common values include:

• “C” (country),

• “ST” (state),

•“L” (locality),

• “O” (organization),

• “OU” (organizational unit), and

• “CN” (common name).

Of these fields, “CN” is usually the most important.

NOTE: For a server certificate, many applications require that the network name of the

server matches the common name in the server’s certificate.

Example To configure the trustpoint named "example" and set its subject name, use the

following commands:

awplus> enable

awplus# configure terminal

awplus(config)# crypto pki trustpoint example

awplus(ca-trustpoint)# subject-name "/O=My

Company/CN=192.168.1.1

Parameter Description

<word> Specify the subject name as a distinguished name string.

Complex strings (e.g., strings containing spaces) should be

surrounded with double-quote characters.

613-50137-01 Rev A Command Reference for FS980M Series 1147

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

PUBLIC KEY INFRASTRUCTURE COMMANDS

SUBJECT-NAME (TRUSTPOINT CONFIGURATION)

Commands

crypto pki enroll

613-50137-01 Rev A Command Reference for FS980M Series 1148

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

TACACS+

Commands

Introduction

Overview This chapter provides an alphabetical reference for commands used to configure

the device to use TACACS+ servers. For more information about TACACS+, see the

TACACS+ Feature Overview and Configuration Guide.

Command List •“authorization commands” on page 1149

•“aaa authorization commands” on page 1151

•“aaa authorization config-commands” on page 1153

•“ip tacacs source-interface” on page 1154

•“show tacacs+” on page 1155

•“tacacs-server host” on page 1157

•“tacacs-server key” on page 1159

•“tacacs-server timeout” on page 1160

613-50137-01 Rev A Command Reference for FS980M Series 1149

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

TACACS+ COMMANDS

AUTHORIZATION COMMANDS

authorization commands

Overview This command applies a command authorization method list, defined using the

aaa authorization commands command, to console and VTY lines.

Use the no variant of this command to reset the command authorization

configuration on the console and VTY lines.

Syntax authorization commands <privilege-level> {default|<list-name>}

no authorization commands <privilege-level>

Default The default method list is applied to each console and VTY line by default.

Mode Line Configuration

Usage If the specified method list does not exist users will not be enable to execute any

commands in the specified method list on the specified VTY lines.

Example To apply the TAC15 command authorization method list with privilege level 15 to

VTY lines 0 to 5, use the following commands:

awplus# configure terminal

awplus(config)# line vty 0 5

awplus(config-line)# authorization commands 15 TAC15

To reset the command authorization configuration with privilege level 15 on VTY

lines 0 to 5, use the following commands:

awplus# configure terminal

awplus(config)# line vty 0 5

awplus(config-line)# no authorization commands 15

Commands

aaa authorization commands

Parameter Description

<privilege-level> The privilege level of the set of commands the method list

will be applied to.

AlliedWare Plus defines three sets of commands, that are

indexed by a level value:

Level = 1: All commands that can be accessed by a user with

privilege level between 1 and 6 inclusive

Level = 7: All commands that can be accessed by a user with

privilege level between 7 and 14 inclusive

Level = 15: All commands that can be accessed by a user

with privilege level 15

default Configure the default authorization commands method list.

<list-name>Configure a named authorization commands method list

613-50137-01 Rev A Command Reference for FS980M Series 1150

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

TACACS+ COMMANDS

AUTHORIZATION COMMANDS

aaa authorization config-commands

tacacs-server host

Command

changes

Version 5.4.6-2.1: command added

613-50137-01 Rev A Command Reference for FS980M Series 1151

AlliedWare Plus™ Operating System - Version 5.4.6-2.x

TACACS+ COMMANDS

AAA AUTHORIZATION COMMANDS

aaa authorization commands

Overview This command configures a method list for commands authorization that can be

applied to console or VTY lines. When command authorization is enabled for a

privilege level, only authorized users can executed commands in that privilege

level.

Use the no variant of this command to remove a named method list or disable the

default method list for a privilege level.

Syntax aaa authorization commands <privilege-level>

{default|<list-name>} group tacac+ [none]

no aaa authorization commands <privilege-level>

{default|<list-name>}

Mode Global Configuration

Usage TACACS+ command authorization provides centralized control of the commands

available to a user of an AlliedWare Plus device. Once enabled:

• The command string and username are encrypted and sent to the first

available configured TACACS+ server (the first server configured) for

authorization.

Parameter Description

<privilege-level> The privilege level of the set of commands the method list

will be applied to.

AlliedWare Plus defines three sets of commands, that are

indexed by a level value:

Level = 1: All commands that can be accessed by a user

with privilege level between 1 and 6 inclusive

Level = 7: All commands that can be accessed by a user

with privilege level between 7 and 14 inclusive

Level = 15: All commands that can be accessed by a user

with privilege level 15

group Specify the server group where authorization messages are

sent. Only the tacacs+ group is available for this

command.

tacac+ Use all TACACS+ servers configured by the tacacs-server

host command.

default Configure the default authorization commands method list.

<list-name>Configure a named authorization commands method list

none If specified, this provides a local fallback to command

authorization so that if authorization servers become

unavailable then the device will accept all commands

normally allowed for the privilege level of the user.

613-50137-01 Rev A Command Reference for FS980M Series 1152