Table of Contents
AOC C32G1 User Manual
Displayed below is the user manual for C32G1 by AOC which is a product in the Computer Monitors category. This manual has pages.
Related Manuals
![](/manual/95/633/bg1.webp)
LCD Monitor User Manual
C24G1/C27G1/C32G1
LED backlight
www.aoc.com
©2018 AOC. All Rights Reserved.
1
![](/manual/95/633/bg2.webp)
Safety ........................................................................................................................................................................ 4
National Conventions ......................................................................................................................................... 4
Power ................................................................................................................................................................ 5
Installation .......................................................................................................................................................... 6
Cleaning............................................................................................................................................................. 7
Other .................................................................................................................................................................. 8
Setup ........................................................................................................................................................................ 9
Contents in Box ................................................................................................................................................. 9
Setup Base ...................................................................................................................................................... 10
Adjusting the monitor ....................................................................................................................................... 11
Connecting the Monitor .................................................................................................................................... 12
Wall Mounting .................................................................................................................................................. 13
FreeSync function ............................................................................................................................................ 14
Adjusting ................................................................................................................................................................. 15
Setting Optimal Resolution .............................................................................................................................. 15
Windows 10 .............................................................................................................................................. 15
Windo ws 8 ................................................................................................................................................ 17
Windo ws 7 ................................................................................................................................................ 19
Hotkeys ............................................................................................................................................................ 21
OSD Setting ..................................................................................................................................................... 22
Luminance ................................................................................................................................................ 23
Image Setup ............................................................................................................................................. 24
Color Setup ............................................................................................................................................... 25
Picture Boost ............................................................................................................................................ 26
OSD Setup ............................................................................................................................................... 27
Game Setting ............................................................................................................................................ 28
Extra ......................................................................................................................................................... 29
Exit............................................................................................................................................................ 30
LED Indicator ................................................................................................................................................... 30
Driver ...................................................................................................................................................................... 31
Monitor Driver .................................................................................................................................................. 31
Windows 10 .............................................................................................................................................. 31
Windo ws 8 ................................................................................................................................................ 35
Windo ws 7 ................................................................................................................................................ 39
i-Menu .............................................................................................................................................................. 42
e-Saver ............................................................................................................................................................ 43
Screen+ ........................................................................................................................................................... 44
Troubleshoot ........................................................................................................................................................... 45
Specification ............................................................................................................................................................ 47
General Specification ....................................................................................................................................... 47
Preset Display Modes ...................................................................................................................................... 50
Pin Assig nments .............................................................................................................................................. 51
Plug and Play ................................................................................................................................................... 53
Regulation ............................................................................................................................................................... 54
FCC Notic e ...................................................................................................................................................... 54
WEEE Declaratio n ........................................................................................................................................... 55
2
![](/manual/95/633/bg3.webp)
WEEE Declaratio n for India ............................................................................................................................. 55
EPA Energy Star .............................................................................................................................................. 57
EPEAT Declaration .......................................................................................................................................... 57
Service .................................................................................................................................................................... 58
Warranty Statement for Europe........................................................................................................................ 58
Warranty Statement for Middle East and Africa (MEA) .................................................................................... 60
AOC International (Europe) B.V. ...................................................................................................................... 62
Warranty Statement for North & South America (excluding Brazil) ........................................................... 63
EASE PROGRAME ......................................................................................................................................... 65
TCO DOCUMENT ........................................................................................................................................... 66
3
![](/manual/95/633/bg4.webp)
Safety
National Conventions
The following subsections describe notational conventions u sed in this do cum ent.
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type.
These blocks are notes, cautions, and warnings, and they are used as follows:
NOTE: A NOTE indicates important information that helps you make better use of your computer system.
CAUTION: A CAUTION indicates e ither potenti al dama ge to hardwar e or loss of dat a a nd tells you how to av oid th e
problem.
WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some
warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specif ic
present at ion of the w arning is mandated by regulatory authority.
4
![](/manual/95/633/bg5.webp)
Power
The monitor should be operated only from the type of power source indicated on the label. If you are not sure
of the type of power supplied to your home, consult your dealer or local power company.
The monitor is equ ippe d with a three-pron ged grou nded plug, a plug w ith a t h ird (grounding) pin. This plu g will
fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug,
have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the
safety purpose of the grounded plug.
Unplug the un it dur ing a light ning stor m or w hen it w ill not be used f or lon g period s of ti me. T his will pr otect th e
monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate
configured receptacles marked between 100 - 240V ~, Min. 5A
The wall socket shall be installed near the equipment and shall be easily accessible.
5
![](/manual/95/633/bg6.webp)
Installation
Do not place the monitor on an unstable cart, stand, tripod, brac ket, or table. If the monitor falls, it can injure a
person and cause ser iou s d am age to this product . Use only a cart , s tand, tripod, bracket, or t able recommended by
the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and
use mounting accessories recommended by the manuf act urer . A product and cart combination should be moved
with care.
Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a fire or
electric shock. Never spill liquids on the monitor.
Do not place the front of the product on the floor.
Leave some space around the monitor as shown below. Otherwise, air-circulation may be inadequate hence
overheating may cause a fire or damage to the monitor.
See below the recommended ventilation areas around the monitor when the mon itor is ins talled on the wall or with
the stand:
10cm
4 inches
6
![](/manual/95/633/bg7.webp)
Cleaning
Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of
strong-detergent which will cauterize the product cabinet.
When clean ing, make sure no detergent is l eak ed int o the product. T he cleani ng cloth sh ould not be t oo rough
as it will scratch the screen surface.
Please disconnect the power cord before cleaning the product.
7
![](/manual/95/633/bg8.webp)
Other
If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and
contact a Service Center.
Make sure that the ventilating openings are not blocked by a table or curtain.
Do not engage the LCD monitor in severe vibration or high impact conditions during operation.
Do not knock or drop the monitor during operation or transportation.
For display with glossy bezel the user should consider the placement of the display as the bezel may cause
disturbing reflections from surrounding light and bright surfaces.
8
![](/manual/95/633/bg9.webp)
Setup
Contents in Box
Not all signal cables (HDMI / DP / VGA cables), CD manual will be provided for all countries and regions.
Please check with the local dealer or AOC branch office for confirmation.
CD Manual Stand Base
Power Cab le HDMI Cable DP Cable VGA Cable
Monitor
9
![](/manual/95/633/bga.webp)
Setup Base
Please setup or remove the base following the steps as below.
Please place the monitor on a soft and flat surf ace to prevent the scratch.
Setup:
Remove:
10
![](/manual/95/633/bgb.webp)
Adjusting the monitor
For optimal viewing, it is recommended to look at the full face of the monitor, and then adjust the monitor's angle to
your own preference.
Hold the stand so you will not topple the monitor when you change the monitor's angle.
NOTE:
Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
11
![](/manual/95/633/bgc.webp)
Connecting the Monit or
Cable Connections In Back of Monitor and Computer:
1 HDMI 2
2 HDMI 1
3 DP
4 Analog (D-Sub 15-Pin VGA cable)
5 Earphone out
6 Power
To protect equipment, always turn off the PC and LCD monitor before connecting.
1. Connect the power cable to the AC port on the back of the monitor.
2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the
computer's D-Sub port.
3. (Optional – Requi res a video card with HDMI port) - Connect one end of the HDMI cable to the back of the
monitor and connect the other end to the computer’s HDMI port.
4. (Optional – Requires a vi deo card with DP port) - Connect o ne end of the DP cable to t h e bac k of the monitor
and connect the other end to the computer’s DP port.
5. Turn on your monitor and computer.
6. Video content su pporting resol ution : VGA/ HDMI/DP
If your monitor displays an image, installation is complete. If it does not display an image, pleas e refer
Troubleshooting.
12
![](/manual/95/633/bgd.webp)
Wall Mounting
Preparing to Install An Optional Wall Mounting Arm.
This monitor c an be attached to a wall mounting arm you purchase separately. Disconnect pow er before thi s
procedure. Follow these steps:
1. Remov e the base.
2. Follow the manufacturer’s instructions to assemble the wall mounting arm.
3. Place the w all moun ting arm onto the back of the monit o r. Line up the holes of the arm with the holes in the back
of the monitor.
4. Insert the 4 screws into the holes and tighten.
5. Reconnect the cables. Refer to the user’s manual that came with the optional wall mounting arm for instructions
on attaching it to the wall.
Noted: VESA mounting screw holes are not available for all models, please check with the dealer or official
depart ment of AOC.
13
![](/manual/95/633/bge.webp)
FreeSync functi on
1. FreeSync function is working with DP/HDMI1/HDMI2
2. Compatible Graphics Card: Recommend list is as the below, also could be checked by vi siting www.AMD.com
AMD Radeon™ RX 480
AMD Radeon™ RX 470
AMD Radeon™ RX 460
Radeon Pro Duo
AMD Radeon R9 300 Series
AMD Radeon R9 Fury X
AMD Radeon R9 360
AMD Radeon R7 360
AMD Radeon R9 295X2
AMD Radeon R9 290X
AMD Radeon R9 290
AMD Radeon R9 285
AMD Radeon R7 260X
AMD Radeon R7 260
14
![](/manual/95/633/bgf.webp)
Adjusting
Setting Optimal Resolution
Windows 10
For Windows 10:
• Right click START.
• Click "CONTROL PANEL".
• Click "DISPLAY".
• Click on the "Change display se ttings" button.
15
![](/manual/95/633/bg10.webp)
• Set the resolution SLIDE-BAR to Optimal preset resolution.
16
![](/manual/95/633/bg11.webp)
Windows 8
For Windows 8:
• Right click and clic k All apps at the bottom-right of the screen.
• Set the "View by" to "Category".
• Click "Appearance and Personalization".
17
![](/manual/95/633/bg12.webp)
• Click "DISPLAY".
• Set the resolution SLIDE-BAR to Optimal preset resolution
18
![](/manual/95/633/bg13.webp)
Windows 7
For Windows 7:
• Click START.
• Click "CONTROL PANEL".
• Click "Appearance".
• Click "DISPLAY".
19
![](/manual/95/633/bg14.webp)
• Click on the "Change display settings" button.
• Set the resolution SLIDE-BAR to Optimal preset resolution
20
![](/manual/95/633/bg15.webp)
Hotkeys
1 Source/Auto/Exit
2 Game Mode/<
3 Dial Point/>
4 Menu/Enter
5 Power
Source/Auto/Exit
When the OSD is closed, press “ ” button will be Source hot key function.
When the OSD is closed, press “ ” button continuously about 2 seconds to do auto configure (Only for the
models with D-Sub).
Game Mode/<
When there is no OSD, press ”<” key to open game mode function, then press ”<” or “>” key to select game mode
(FPS, RTS, Racing, Gamer 1, Gamer 2 or Gamer 3) bas ing o n the differ ent ga me type s.
Dial Point
When there is no OSD , press Dial Point button to active Dial Point menu, and then press “<” or “>” to s et Dial Point
on or off.
Menu/Enter
When there is no OSD, Press to display the OSD or confirm the selection. Press about 2 second to turn off the
monitor
Power
Press the Power button to turn on the monitor.
21
![](/manual/95/633/bg16.webp)
OSD Setting
Basic and simple instruction on the control keys.
1. Press the MENU-button to activate the OSD window.
2. Press or to navigate through the functions. Once the desired function is highlighted,
press the to activate it. If there is a sub-menu, press or t o nav igate through the sub-menu
functions.
3. Press or
to change the settings of the selected function. Press to exit. If you want to adjust
any other function, repeat steps 2-3.
4. OSD Lock Functio n: To lock the OSD, press and hold the MENU-button while the monitor is off and
then press power button to turn the monitor on. To un-lock the OSD - press and hold the
MENU-button while the monitor is off and then press power button to turn the m onitor on.
Notes:
1. If the product has only one s i gnal input, the item of "Input Sel ect" is di sabl ed.
2. If the product screen size is 4:3 or input signal resolution is native resolution, the item of "Image Ratio" is
disabled.
3. One of Clear vision, DCR, Color Boost, and Picture Boost functions is activated; the other three functions are
turned off accord ingly.
22
![](/manual/95/633/bg17.webp)
Luminance
1 Press MENU (Menu) to display menu.
2 Press or to select (Luminance), and press to enter.
3 Press or to select submenu.
4 Press or to adjust.
5 Press to exit.
Contrast 0-100 Contrast from Digital-register.
Brightness 0-100 Backlight Adjustment
Eco mode
Standard
Standard Mode
Text
Text Mo de
Internet
Internet Mode
Game
Game Mode
Movie
Movie Mode
Sports
Sports Mode
Gamma
Gamma1 Adjust to Gamma 1
Gamma2 Adjust to Gamma 2
Gamma3 Adjust to Gamma 3
DCR
Off Disable dynamic contrast ratio
On
Enable dynamic contrast ratio
23
![](/manual/95/633/bg18.webp)
Image Setup
1 Press MENU (Menu) to display menu.
2 Press or to select (Luminance), and press to enter.
3 Press or to select submenu.
4 Press or to adjust.
5 Press to exit.
Clock 0-100 Adjust pic ture Clock to reduce Vertical-L ine noi se.
Phase 0-100 Adjust Picture Phase to reduce Horizontal-Line noise.
Sharpness 0-100 Adjust picture sharpness.
H. Position 0-100 Adjust the horizontal position of the picture.
V. Position 0-100 Adjust the vertical position of the picture.
24
![](/manual/95/633/bg19.webp)
Color Setup
1 Press MENU (Menu) to display menu.
2 Press or to select (Luminance), and press to enter.
3 Press or to select submenu.
4 Press or to adjust.
5 Press to exit.
Color Temp.
Warm Recall Warm Color Temperature from EEPROM.
Normal Recall Normal Color Temperature from EEPROM.
Cool Recall Cool Color Temperature from EEPROM.
sRGB Recall SRGB Color Temperature from EEPROM.
User Recall User Color Temperature from EEPROM
DCB Mode
Full Enhance
ON/OFF Disable or Enable Full Enhance Mode.
Nature Skin ON/OFF Disable or Enable Nature Skin Mode.
Green Field ON/OFF Disable or Enable Green Field Mode.
Sky-blue ON/OFF Disable or Enable Sky-blue Mode.
AutoDetect ON/OFF Disable or Enable AutoDetect Mode.
DCB Demo ON/OFF Disable or Enable Demo.
Red 0-100 Red gain from Digital-register.
Green 0-100 Green gain from Digi tal-register.
Blue 0-100 Blue gain from Digital-register.
25
![](/manual/95/633/bg1a.webp)
Picture Boost
1 Press MENU (Menu) to display menu.
2 Press or to select (Luminance), and press to enter.
3 Press or to select submenu.
4 Press or to adjust.
5 Press to exit.
Bright Frame ON/OFF Enable/Disable Bright Frame
Frame Size 14-100 Adjust the Size of the Frame
Brightness 0-100 Brightness Adjustment for Enhance Area
Contrast 0-100 Contrast Adjustment for Enhance Area
H. position 0-100 Adjust the horizontal position of the Frame
V. position 0-100 Adjust the vertical position of the Frame
Note:
Adjust the brightness, contrast, and position of the Bright Frame for better viewing experience.
26
![](/manual/95/633/bg1b.webp)
OSD Setup
1 Press MENU (Menu) to display menu.
2 Press or to select (Luminance), and press to enter.
3 Press or to select submenu.
4 Press or to adjust.
5 Press to exit.
Language Select the OSD language.
Timeout 5-120 Adjust the OSD timeout.
DP Capability 1.1/1.2
please be noted that only DP1.2 support free sync
function
H. Position 0-100 Adjust the horizontal position of the OSD.
V. Position 0-100 Adjust the vertical position of the OSD.
Volume 0-100 Volume Adjustment.
Transparence 0-100 Adjust the OSD.
Break Reminder on or off Break reminder if the user continuously work for more
than 1hrs.
Notes:
If the DP video content supports DP1.2, please select DP1.2 for DP Capability; otherwise, please select DP1.1
27
![](/manual/95/633/bg1c.webp)
Game Setti ng
1. Press MENU-button to display menu.
2. Press or to select (Game setting), and press MENU-button to enter.
3. Press or to select submenu, and press MENU-button to enter.
4. Press or to adjust.
5. Press AUTO-button to exit.
Game Mode
FPS
For playing FPS (first Person Shooters) games.
Improves dark theme black level details.
RTS
For playing RTS (Real Time Strategy). Improves the
image quality.
Racing
For playing Racing games, Provides fastest response
time and high color satur ati on.
Gamer 1
User’s preference settings saved as Gamer 1.
Gamer 2
User’s preference settings saved as Gamer 2.
Gamer 3
User’s preference settings saved as Gamer 3.
off
No optimization by Sm art image game
Shadow Control 0-100
Shadow Control Default is 50, then end-user can adjust
from 50 to 10 0 or 0 to i
ncrease contr a st f or cl ear p ict ure.
1. If picture is too dark to be saw the detail clearly,
adjusting from 50 to100 for clear picture..
2. If picture is too white to be saw the detail clearly,
adjusting from 50 to0 for clear picture
Low input Lag On/off Turn off frame buffer to dec rease input lag
Game Color 0-20
Game Color will provide 0-20 level for adjusting
saturation to get better picture.
LowBlue Mode
Reading / Office /
Internet /
Multimedia / Off
Decrease blue light wave by controll ing color
temperature.
Overdrive
Weak
Adjust the response time.
(Boost can only enable in FreeSync off mode)
Medium
Strong
Boost
(
Motion
picture response
time 1ms
)
Off
FreeSync
On/Off
Adjust the FreeSync.
Frame Counter
Off / Right-Up /
Right-Down /
Left-Down /
Left-Up
Display vertical scanning frequency
MBR 0-20
MBR(Motion Blur Reduction) will provide 0 – 20 levels
for adjusting visib le mot ion blu r.
Note:
Boost or MBR must be above 75Hz refresh rate to start.
28
![](/manual/95/633/bg1d.webp)
Extra
1 Press MENU (Menu) to display menu.
2 Press or to select (Luminance), and press to enter.
3 Press or to select submenu.
4 Press or to adjust.
5 Press to exit.
Input Select Auto/D-SUB/HDMI1/HDMI2/DP Select input sig nal sour ce.
Auto Config. Yes / No Auto adjust.the picture to default.
Off Timer 0-24 hrs Select DC off time.
Image Ratio
Wide
Select image ratio for display.
4:3
1:1
17” (4:3)
19” (4:3)
19” (5:4) (C27G1/C32G1)
19” W (16:10)
21.5” W (16:9)
22” W (16:10) (C27G1/C32G1)
23” W (16:9)
23.6” W (16:9) (C27G1/C32G1)
24”W (16:9) (C27G1/C32G1)
DDC/CI Yes / No Turn on or off DDC/CI Support.
Reset Yes / No Reset the menu to default.
29
![](/manual/95/633/bg1e.webp)
Exit
1 Press MENU (Menu) to display menu.
2 Press or to select (Luminance), and press to enter.
3 Press to exit.
LED Indicator
Status LED Color
Full Power Mode White
Power Saving Orange
30
![](/manual/95/633/bg1f.webp)
Driver
Monitor Driver
Windows 10
• Start Windows® 10
• Right click START.
• Click "Control Panel".
• Click on the "Display" icon.
31
![](/manual/95/633/bg20.webp)
• Click on the "Change display settings" button
• Click the "Advanced Settings" button.
32
![](/manual/95/633/bg21.webp)
• Click the "Monitor" tab and then click the "Properties" button.
• Click the "Driver" tab.
• Open the "Update Driver Software-Generic PnP Monitor" window by clicking on "Up d ate Dr iv er... “and then
click the "Browse my computer for driver software" button.
33
![](/manual/95/633/bg22.webp)
• Select "Let me pick from a list of device drivers on my computer".
• Click the "Have Disk" button. Click on the "Browse" button and navigate to the following directory:
X:\Driver\module name(where X is the drive letter designator for the CD-ROM drive).
• Select the "xxx.inf" file and cl ick the "Open" button. Click the "OK" button.
• Select your monitor model and click the "Next" button. The files will be copied from the CD to your hard disk
drive.
• Close all open windows and remove the CD.
• Restart the sy ste m. The syste m will autom atic ally sel ect the maximum refresh rat e and corresponding Color
Matching Profiles.
34
![](/manual/95/633/bg23.webp)
Windows 8
• Start Windows® 8
• Right click and clic k All apps at the bottom-right of the screen.
• Click on the "Control Panel" icon
• Set the "View by" to "Large icons" or "S mall icons".
35
![](/manual/95/633/bg24.webp)
• Click on the "Display" icon.
• Click on the "Change display settings" button.
• Click the "Advanced Settings" button.
36
![](/manual/95/633/bg25.webp)
• Click the "Monitor" tab and then click the "Properties" button.
• Click the "Driver" tab.
• Open the "Update Driver Software-Generic PnP Monitor" window by clicking on "Update Driver... " and
then click the "Brow se my computer for driver software" button.
37
![](/manual/95/633/bg26.webp)
• Select "Let me pick from a list of device drivers on my computer".
• Click the "Have Disk" but ton . C lick on the "Browse" button and navigat e to the following directory:
X:\Driver\module name (where X is the drive letter designator for the CD-ROM drive).
• Select the "xxx.inf" f ile and click the "Open" button. Click the "OK" button.
• Select your monitor model and click the "Next" button. The files will be copied from the CD to your hard disk
drive.
• Close all open windows and remove the CD.
• Restart the system. The system will automatically select the maximum refresh rate and corresponding Color
Matching Profiles.
38
![](/manual/95/633/bg27.webp)
Windows 7
• Start Windows® 7
• Click on the "Start" button and then click on "Control Panel".
• Click on the "Display" icon.
• Click on the "Change display settings" button.
39
![](/manual/95/633/bg28.webp)
• Click the "Advanced Settings" button.
• Click the "Monitor" tab and then click the "Properties" button.
• Click the "Driver" tab.
40
![](/manual/95/633/bg29.webp)
• Open the "Update Driver Software-Generic PnP Monitor" window by clicking on “Update Driver... " and
then click the "Browse my computer for driver software" button.
• Select "Let me pick from a list of device drivers on my computer".
• Click the "Have Disk" b utton . Click on the "Browse" button and navigate to the following directory:
X:\Driver\module name(where X is the drive letter designator for the CD-ROM drive).
• Select the "xxx.inf" f ile and cli ck the "Open" button. Click t he "OK" button.
• Select your monitor model and click the "Next" button. The files will be copied from the CD to your hard disk
drive.
• Close all open windows and remove the CD.
• Restart the sy ste m. The syste m will autom atic ally sel ect the maximum refresh rate and corresponding Color
Matching Profiles.
41
![](/manual/95/633/bg2a.webp)
i-Menu
Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on
screen menus instead of the OSD button on the monitor. To complete installation, please follow the installation
guide.
42
![](/manual/95/633/bg2b.webp)
e-Saver
Welcome to use AOC e-Saver monitor power management software! The AOC e-Saver features Smart Shutdown
functions for y our mon itors, allows y our monito r to t i mely s hutdown when PC unit is at any s t atus (O n, O ff , S lee p or
Screen Saver); the actual shutdown time depends on your preferences (see example below).
Please click on "driver/e-Saver/setup.exe" to start installing the e-Saver software, follow the install wizard to
complete software installation.
Under each of the four PC statuses, you may choose the desired time (in minutes) from the pull-down menu for
your monitor to automatically shutdown. The example below illustrated:
1) The monitor will never shutdown when the PC is powered on.
2) The monitor will automatically shutdown 5 minutes after the PC is powered off.
3) The monitor will automatically shutdown 10 minutes after the PC is in sleep/stand-by mode.
4) The monitor will automatically shutdown 20 minutes after the screen saver appears.
You can click “RESET” to set the e-Saver to its default settings like below.
43
![](/manual/95/633/bg2c.webp)
Screen+
Welcome to "Screen+" software by AOC. Screen+ software is a desktop screen splitting tool; it splits the desktop
into dif feren t pa nels, and each panel displays a different window. You only need to drag the window to a
corresponding panel when you want to access it. It supports multiple monitor display to make your task easier.
Please follow the installation software to install it.
44
![](/manual/95/633/bg2d.webp)
Troubleshoot
Problem & Question Possible Solutions
Power LE D Is Not ON M ake sure th e pow er butt on is ON and the P ow er Cord is pro perly co nnected
to a grounded power outlet and to the monitor.
No images on the screen
Is the power cord connected properly?
Check the power cord connection and power supply.
Is the cable connected co rrectly?
(Connected using the D-sub c able)
Check the DB-15 cable connection.
(Connected us ing the DVI cab l e)
Check the DVI cable connection.
(Connected us ing the HDMI cable)
Check the HDMI cable connection.
(Connected us ing the DP cable)
Check the DP cable connection.
* DVI/HDMI/DP input is not available on every model.
If the power is on, reboot the computer to see the initial screen (the login
screen), which can be seen.
If the initial screen (the login screen) appears, boot the computer in the
applicable mod e (the safe mode for Windows 7/8/10) and then change
the frequency of the video card.
(Refer to the Setting the Optimal Resolution)
If the initial screen (the login screen) does not appear, contact the
Service Center or your dealer.
Can you see "Input Not Supported" on the screen?
You can see this message when the s ignal from the video card exceeds
the maximum resolution and frequency that the m onitor can handle
properly.
Adjust the maximum resolution and frequency that the m onitor can
handle properly.
Make sure the AOC Monitor Drivers are installed.
Picture Is Fuzzy & Has
Ghosting Shadowing Problem
Adjust the Contrast and Brightness Controls.
Press to auto adjust.
Make sure you are not using an extension cable or switch box. We
recommend plugging the monitor directly to the video card output connector
on the back.
45
![](/manual/95/633/bg2e.webp)
Picture Bounces, Flickers Or
Wave Pattern Appears In The
Picture
Move electrical devices that may cause electrical interference as far away
from the monitor as possible.
Use the maximum refresh rate your monitor is capable of at the resolution
you are using.
Monitor Is Stuck In Active
Off-Mode"
The Computer Power Switch should be in the ON position.
The Computer Video Card should be snugly fitted in its slot.
Make sure the monitor's video cable is properly connected to the computer.
Inspect the monitor's video cable and make sure no pin is bent.
Make sure your computer is operational by hitting the CAPS LOCK key on
the keyboard while observing the CAPS LOCK LED. The LED should either
turn ON or OFF after hitting the CAPS LOCK key.
Missing one of the primary
colors (RE D, GREEN, or
BLUE)
Inspect the m onitor's video cable and make sure that no pin is damaged.
Make sure the monitor's video cable is properly connected to the computer.
Screen image is not centered
or sized properly Adjust H-Position and V-Position or press hot-key (AUTO).
Picture has color defects
(white does not look white) Adjust RGB color or select desired color temperature.
Horizontal or vertical
disturbances on the screen
Use Window s7/8/10 shut-down mode to adjust CLOCK and PHASE.
Press to auto-adjust.
46
![](/manual/95/633/bg2f.webp)
Specification
General Specification
Panel
Model name
C24G1
Driving system
TFT Color LCD
Viewable Image Size
59.8cm diagonal
Pixel pitch 0.2715(H)mm x 0.2715(V)mm
Video R, G, B Analog Interface & HDMI Interface & DP Interface
Separate Sync.
H/V TTL
Display Color
16.7M 6bits+Hi FRC
Others
Horizontal scan range
30~160KHz
Horizontal scan
Size(Maximum) 521.39mm
Vertical scan range 50-146Hz(D-SUB)
48-146Hz(HDMI、DP)
Vertical scan Size(Maximum) 293.28mm
Optimal preset resolution 1920x1080@60Hz(D-SUB)
1920x1080@144Hz(HDMI、DP)
Plug & Play
VESA DDC2B/CI
Input Connector D-Sub 15 pin/HDMI/DP
Power Source 100-240V~,50/60Hz
Power Consumption
Typical (Brightness = 90,Contrast = 50)
21W
(Brightness = 100,Contrast = 100)
≤ 29W
Power saving ≤0.5W
Off timer 0-24 hrs
Physical
Characteristics
Connector Type
D-Sub/ HDMI/DP/Earphone out
Signal Cable Type
Detachable
Environmental
Temperature:
Operating
0° to 40°C
Non-Operating -25° to 55°C
Humidity: Operating 10% to 85% (non-condensing)
Non-Operating
5% to 93% (non-condensing)
Altitude:
Operating
0~ 5000m(0~ 16404 ft)
Non-Operating
0~ 12192m (0~ 40000 ft )
47
![](/manual/95/633/bg30.webp)
Panel
Model name
C27G1
Driving system
TFT Color LCD
Viewable Image Size 68.6 cm diagona l
Pixel pitch
0.3114 (H)mm x 0.3114(V)mm
Video
R, G, B Analog Interface & HDMI Interface & DP Interface
Separate Sync.
H/V TTL
Display Color 16.7M
Others
Horizontal scan range 30~160KHz
Horizontal scan
Size(Maximum)
597.888 mm
Vertical scan range 50-146Hz(D-SUB)
48-146Hz(HDMI、DP)
Vertical scan Size(Maximum) 336.312 mm
Optimal preset resolution 1920x1080@60Hz(D-SUB)
1920x1080@144Hz(HDMI、DP)
Plug & Play
VESA DDC2B/CI
Input Connector D-Sub 15 pin/HDMIx2/DP
Power Source 100-240V~, 50/60Hz
Power Consumption
Typical (Brightness = 90,Contrast = 50)
29W
(Brightness = 100,Contrast = 100) ≤ 41W
Power saving ≤0.5W
Off timer
0-24 hrs
Physical
Characteristics
Connector Type
D-Sub/ HDMI/DP/Earphone out
Signal Cable Type
Detachable
Environmental
Temperature: Operating 0° to 40°C
Non-Operating -25° to 55°C
Humidity:
Operating
10% to 85% (non-condensing)
Non-Operating
5% to 93% (non-condensing)
Altitude:
Operating
0~ 5000m(0~ 16404 ft)
Non-Operating 0~ 12192m (0~ 40000 ft )
48
![](/manual/95/633/bg31.webp)
Panel
Model name
C32G1
Driving system
TFT Color LCD
Viewable Image Size 80.0 cm diagona l
Pixel pitch
0.36375 (H)mm x 0.36375(V)mm
Video
R, G, B Analog Interface & HDMI Interface & DP Interface
Separate Sync.
H/V TTL
Display Color 16.7M
Others
Horizontal scan range 30~160KHz
Horizontal scan
Size(Maximum)
698.4 mm
Vertical scan range 50-146Hz(D-SUB)
48-146Hz(HDMI、DP)
Vertical scan Size(Maximum) 392.85 mm
Optimal preset resolution 1920x1080@60Hz(D-SUB)
1920x1080@144Hz(HDMI、DP)
Plug & Play
VESA DDC2B/CI
Input Connector D-Sub 15 pin/HDMIx2/DP
Power Source 100-240V~, 50/60Hz
Power Consumption
Typical (Brightness = 90,Contrast = 50)
35W
(Brightness = 100,Contrast = 100) ≤ 50W
Power saving ≤0.5W
Off timer
0-24 hrs
Physical
Characteristics
Connector Type
D-Sub/ HDMI/DP/Earphone out
Signal Cable Type
Detachable
Environmental
Temperature: Operating 0° to 40°C
Non-Operating -25° to 55°C
Humidity:
Operating
10% to 85% (non-condensing)
Non-Operating
5% to 93% (non-condensing)
Altitude:
Operating
0~ 5000m(0~ 16404 ft)
Non-Operating 0~ 12192m (0~ 40000 ft )
49
![](/manual/95/633/bg32.webp)
Preset Display Modes
Standard
Resolution
H. Freque ncy (kHz)
V. Frequency (Hz)
VGA
640x480@60Hz
31.469
59.94
640x480@72Hz 37.861 72.809
640x480@75Hz 37.500 75.000
MAC MODES VGA 640x480@67Hz 35.000 66.667
IB M M O D E
720x400@70Hz
31.469
70.087
SVGA
800x600@56Hz
35.156
56.25
800x600@60Hz 37.879 60.317
800x600@72Hz 48.077 72.188
800x600@75Hz 46.875 75.000
MAC MIDE SVGA
835 x 624@75Hz
49.725
74.500
XGA
1024x768@60Hz
48.363
60.004
1024x768@70Hz 56.476 70.069
1024x768@75Hz 60.023 75.029
SXGA 1280x1024@60Hz 63.981 60.020
1280x1024@75Hz 79.976 75.025
WSXG
1280x720@60HZ
45.000
60.000
1280x960@60HZ 60.000 60.000
WXGA+ 1440x900@60Hz 55.935 59.876
WSXGA+ 1680x1050@60Hz 65.290 59.954
FHD
1920x1080@60Hz
67.500
60.000
50
![](/manual/95/633/bg33.webp)
Pin Assignments
15-Pin Color Display Signal Cable
Pin No.
Signal Name
Pin No.
Signal Name
1
Video-Red
9
+5V
2
Video-Green
10
Ground
3
Video-Blue
11
N.C.
4
N.C.
12
DDC-Serial data
5
Detect Cable
13
H-sync
6
GND-R
14
V-sync
7
GND-G
15
DDC-Serial clock
8
GND-B
19-Pin Color Display Signal Cable
Pin No. Signal Name Pin No. Signal Name
1
TMDS Data 2+
11
TMDS Clock Shield
2
TMDS Data 2 Shield
12
TMDS Clock
3
TMDS Data 2
13
CEC
4
TMDS Data 1+
14
Reserved (N.C. on device
5
TMDS Data 1Shield
15
SCL
6
TMDS Data 1
16
SDA
7
TMDS Data 0+
17
DDC/CEC Ground
8
TMDS Data 0 Shield
18
+5V Power
9
TMDS Data 0
19
Hot Plug Detect
10
TMDS Clock +
51
![](/manual/95/633/bg34.webp)
20-Pin Color Display Signal Cable
Pin No. Signal Name Pin No. Signal Name
1 ML Lane 3(n) 11 GND
2 GND 12 ML Lane 0(p)
3 ML Lane 3(p) 13 CONFIG1
4 ML Lane 2(n) 14 CONFIG2
5
GND
15
AUX CH(p)
6 ML Lane 2(p) 16 GND
7
ML Lane 1(n)
17
AUX CH(n)
8
GND
18
Hot Plug Detect
9
ML Lane 1(p)
19
Return OP PWR
10
ML Lane 0(n)
20
D P P WR
52
![](/manual/95/633/bg35.webp)
Plug and Play
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the
monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional
information about its display capabilities.
The DDC 2B is a bi-directio nal data c hannel ba sed on the I2C prot ocol. T he host can req ues t EDI D informat ion over
the DDC2B channel.
53
![](/manual/95/633/bg36.webp)
Regulation
FCC Notice
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not
installed and used in accordance with the instruc tions, may cause harmful interference to radio communications.
However, there is no guarantee that interference w ill not occ ur in a part icular in st al lation. If this equipm ent does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
NOTICE:
The changes or mo dification s not expressly approved by the p art y r espo ns ible f or co mpl ian ce co uld v oid th e user's
authority to operate the equipment.
Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this
equipment. It is the responsibilitie s of the user to correct such interference. It is the responsibility of the user to
correct such interference.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
54
![](/manual/95/633/bg37.webp)
WEEE Declaration
Disposal of Waste Equipment by Users in Private Household in the European Union.
This symbol on the product or on its packaging indicates that this product m ust not be disposed of with your other
household waste. Instead, it is your responsibility to dispose of your waste equipment by handi ng it over to a
designated collection point for the recycling of waste electrical and electronic equipment. The separate collection
and recycling of your waste equipment at the time of disposal wi ll hel p to conserve natural resources and ensure
that it is recycled in a manner that protects human health and the environment. For more information about where
you can drop off your waste equipment for recycling, please contact your local city office, your household waste
disposal service or the shop where you purchased the product.
This product complies with all implemented RoHS type regulations worldwide, including but not limited to, EU,
Korea, Japan, US States (e.g. California), Ukraine, Serbia, Turkey, Vietnam and India.
We continue to monitor, influence and develop our proc esses to comply with upcoming proposed RoHS type
regulatio ns, in clud ing but not limited to, Brazil, Argentina, Canada.
WEEE Declaration for India
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other
household w aste. Inst ead it is y our respons ibi lit y to di spo se of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and electronic equipment. The separate collection
and recycling of your waste equipment at the time of disposal wi ll hel p to conserve natural resources and ensure
that it is recycled in a manner that protects human health and the environment. For more information about E
-waste plea se v isit http : //www.aocindi a.c om/ ewaste.php and to kn ow where you can drop off your waste e quip me nt
for recycling in India please contact on below given contact details.
Helpline number: 080-6788-6788 / 080-3323-1313 (Monday to Saturday, 10 a.m. to 6 p.m.)
Centralized E-waste collection center
Address: TPV Technology India Private Limited, 59, Maheswari Nagar, 1st Main Road, Mahadevapura Post,
Whitefield Road, Bangalore, Karnataka, PIN: 560048, Tel: 080-3023-1000
E-mail: serviceindia@aoc.com
55
![](/manual/95/633/bg38.webp)
Restricti on on Hazardous Sub stances statement ( India)
This product com plies with the “E-Waste (Management) Rules, 2016” CHAPTER V, rule 16, sub-rule (1) . Whereas
New Electrical and Electronic Equipm ent and their components or consumables or parts or spares do not contain
Lead, Mercury, Cadmium, Hexavalent Chromium, polybrominated biphenyls and polybrominated di phenyl ethers
beyond a maximum concentration value of 0.1% by weight in homogenous materials for lead, mercury, hexavalent
chromium, polybrominated biphenyls and polybrominated diphenyl ethers and of 0.01% by weight in homogenous
materials for cadmium. except of exemptions set in Schedule 2 of the Rule.
56
![](/manual/95/633/bg39.webp)
EPA Energy Star
ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® Partner, AOC International (Europe) BV and
Envision Peripherals, Inc. have determined that this product meets the ENERGY STAR® guidelines for energy
efficiency. (FOR EPA CERTIFIED MODELS)
EPEAT Declaration
EPEAT is a system to help purchasers in the public and private sectors evaluate, compare and select desktop
computers, notebooks and monitors based on their environmental attributes. EPEAT also provides a clear and
consistent set of performance criteria for the design of products, and provides an opportunity for manufacturers to
secure market recognition for efforts to reduce the environmental impact of its products.
AOC believes in protecting the environment. With a key concern for the conservation of natural resources, as well
as landfill protection, AOC announces the launch of AOC monitor’s packaging recycling program. This program is
designed to help you discard of your monitor carton and filler materials properly. If a local recycling center is not
available, AOC will recycle the packaging material for you, including foam filler and carton. AOC Display solution
will only recycle AOC monitor packaging. Please refer to the following website address:
Only for North and South American, excluding Brazil:
http://us.aoc.com/aoc-corporation/?page=environmental-impact
For Germany:
http://aoc-europe.com/de/content/environment
For Brazil:
http://www.aoc.com.br/pg/embalagem-verde
57
![](/manual/95/633/bg3a.webp)
Service
Warranty Statement for Europe
LIMITED THREE-YEAR WARRANTY*
For AOC LCD Monitors sold within Europe, AOC International (Europe) B.V. warrants this product to be free from
defects in material and workmanship for a period of Three (3) years after the original date of consumer purchase.
During this period, AOC International (Europe) B.V. will, at its option, either repair the defective product with new or
rebuilt parts, or replace it with a new or rebuilt product at no charge except as *stated below. In the absent of the
proof of purchase, the warranty will start 3 months after the date of manufacturing indicated on the product.
If the product appears to be defective, please contact your local dealer or refer to the service and support section
on www.aoc-europe.com for the warranty instructions in your country. The freight cost for the warranty is pre-paid
by AOC for the delivery and return. Please ensure you provide a dated proof of purchase along with the product
and deliver to the AOC Certified or Authorized Service Center under the following condition:
• Make sure the LCD Monitor is packed in a proper carton box (AOC prefers the original carton box to
protects your monitor well enough during transport).
• Put the RMA number on the address label
• Put the RMA number on the shipping carton
AOC International (Europe) B.V. will pay the return s hip ping charges w ithi n o ne of the countr ies s pec ifie d within this
warranty statement. AOC International (Europe) B.V. is not responsible for any costs associated with the
transportation of product across international borders. This includes the international border within the European
Union. If the LCD Monitor is not available for collection when the currier attends, you will be charged a collection
fee.
* This limited warranty does not cover any losses or damages that occur as a result of:
• Damages during trans port due to improper packaging
• Improper installation or maintenance other then in accordance with AOC’s user manual
• Misuse
• Neglect
• Any cause other than ordinary commerci al or industrial application
• Adjustment by non-authoriz ed sour ce
• Repair, modification, or installation of options or parts by anyone other than an AOC Certified or
Authorized Service Center
• Improper environments like humidity, water damage and dusts
• Damaged by violence, earthquake and terrorist attacks
• Excessive or inade quate heating or air cond itio nin g or electr i cal pow er s failure s, surg es, or other
irregularities
This limited warranty does not cover any of the product firmware or hardware that you or any third party have
modified or altered; you bear the sole responsibility and li ability for any s uch modifications or alteration.
58
![](/manual/95/633/bg3b.webp)
All AOC LCD Monitors are produced according to the ISO 9241-307 Class 1 pixel policy standards.
If your w arranty has ex pired, you sti ll have a cces s to all av ailable s ervice o ptions , but you w ill be re spons ible for the
cost of service, including parts, labor, shipping (if any) and applicable taxes. AOC Certified or Authorized Service
Center will provide you with an estimate of service costs before receiving your authorization to perform service.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNES S FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A
PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR FROM THE ORIGINAL DATE OF CONSUMER
PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER THIS PERIOD. AOC
INTERNATIONAL (EUROPE) B.V. OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY AND
EXCULSIVELY AS STATED HERE. AOC INTERNATIONAL ( EUROPE) B.V. LIABILITY, WHETHER BASED ON
CONTRACT, TORT, WARRANTY, STRICT LIABILITY, OR OTHER THEORY, SHALL NOT EXCEED THE PRICE
OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN NO EVENT
SHALL AOC INTERNATIONA L (EUROPE) B.V. BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE OR
FACILITIES OR EQUIPMENT, OR OTHER INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE. SOME
STATES DO NO T ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO Y O U. ALTHOUGH THIS LIMITED WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE O THER RIGHTS, WHICH MAY VARY FROM
COUNTRY TO COUNTRY. THIS LIMITED WARRANTY IS ONLY VALID FOR PRODUC TS PURCHASED IN THE
MEMBER COUNTRIES OF THE EUROPEAN UNION.
Information in this document is subject to change without notice. For more information, please visit:
http://www.aoc-europe.com
59
![](/manual/95/633/bg3c.webp)
Warranty Statement for Middle East and Africa (MEA)
And
The Commonwealth of Independent States (CIS)
LIMITED ONE to THREE YEARS WARRANTY*
For AOC LCD Monitors sold within the Middle East and Africa (MEA) and the Commonwealth of Independent
States (CIS), AOC International (Europe) B.V. warrants this product to be free from defects in material and
workmanship for a period of One (1) to Three (3) years from the manufacture date depending on sale country.
During this period, AO C International (Eur ope) B. V. off ers a Carry-In (return t o Serv ic e C en ter ) Warranty Support at
an AOC’s Authorized Service Center or Dealer and at its option, either repair the defective product with new or
rebuilt parts, or replace it with a new or rebuilt product at no charge except as *stated below. As a Standard Policy,
the warranty will be calculated from the manufacture date identified from the product ID serial number, but the total
warranty will be Fifteen (15) months to Thirty Nine (39) months from MFD (manufacture date) depending on sale
country. Warranty will be considered for exceptional cases that are out of warranty as per the product ID seri al
number and for such exceptional cases; Original Invoice/Proof Of Purchase Receipt is mandatory.
If the product appears to be defective, please contact your AOC authorized dealer or refer to the service and
support section on AOC’s website for the warranty instructions in your c ount ry:
• Egypt: http://aocmonitorap.com/egypt_eng
• CIS Central Asia: http://aocmonitorap.com/ciscentral
• Middle East: http://aocmonitorap.com/middleeast
• South Africa: http://aocmonitorap.com/southafrica
• Saudi Arabia: http://aocmonitorap.com/saudiarabia
Please ensure you provide a dated proof of purchase along with the produc t and deliver to the AOC Authorized
Service Center or Dealer under the fol lowing condition:
• Make sure the LCD Monitor is packed in a proper carton box (AOC prefers the original carton box to
protects your monitor well enough during transport).
• Put the RMA number on the address label
• Put the RMA number on the shipping carton
* This limited warranty does not cover any losses or damages that occur as a result of:
• Damages during trans port due to improper packaging
• Improper installation or maintenance other then in accordance with AOC’s user manual
• Misuse
• Neglect
• Any cause other than ordinary commerci al or industrial application
• Adjustment by non-authoriz ed sour ce
60
![](/manual/95/633/bg3d.webp)
• Repair, modification, or installation of options or parts by anyone other than an AOC Certified or
Authorized Service Center
• Improper environments like humidity, water damage and dusts
• Damaged by violence, earthquakes and terrorist attacks
• Excessive or inadequate heating or ai r conditionin g or electri cal powers failure s, surg es, or other
irregularities
This limited warranty does not cover any of the product firmware or hardware that you or any third party have
modified or altered; you bear the sole responsibility and li ability for any s uch modifications or alteration.
All AOC LCD Monitors are produced according to the ISO 9241-307 Class 1 pixel policy standards.
If your w arranty has ex pired, you sti ll have a cces s to all av ailable s ervice o ptions , but you w ill be re spons ible for the
cost of service, including parts, labor, shipping (if any) and applicable taxes. AOC Certified, Authorized Service
Center or dealer will provide you with an estimate of service costs before receiving your authorization to perform
service.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNES S FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A
PERIOD OF ONE (1) to THREE (3) YEARS FOR PARTS AND LABOR FRO M THE ORIGINAL DATE OF
CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER THIS
PERIOD. AOC INTERNATIONAL (EUROPE) B.V. OBL IGATIONS AND YOUR REMEDIES HEREUNDER ARE
SOLELY AND EXCULSIVELY AS STATED HERE. AOC INTERNATIONAL (EUROPE) B.V. LIABILITY, WHETHER
BASED ON CONTRACT, TORT, WARRANTY, STRICT LIABILITY, OR OTHER THEORY, SHALL NOT EXCEED
THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN NO
EVENT SH ALL AOC INTERNATIONAL (EUROPE) B.V. BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE
OR FACILITIES OR EQUIPMENT, OR OTHER INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO Y O U. ALTHOUGH THIS LIMITED WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS, WHICH MAY VARY FROM
COUNTRY TO COUNTRY. THIS LIMITED WARRANTY IS ONLY VALID FOR PRODUC TS PURCHASED IN THE
MEMBER COUNTRIES OF THE EUROPEAN UNION.
Information in this document is subject to change without notice. For more information, please visit:
http://www.aocmonitorap.com
61
![](/manual/95/633/bg3e.webp)
AOC International (Europe) B.V.
Prins Bernhardplein 200 / 6th floor, Amst erdam, T he Netherlands
Tel: +31 (0)20 504 6962 • Fax: +31 (0)20 5046933
AOC Pixel Policy
ISO 9241-307 Class 1
July 25th, 2013
AOC strives to deliver the highest quality products. We use some of the industry’s most advanced manufacturing
processes and practice stringent qu al ity control. However, pixel or su b pi xel defects on the TFT monitor panels used in
flat pan el monitors are sometimes unavoi dable. No manufacturer can guarantee th at al l panels will be free f rom pixel
defects, bu t AOC guarantees that an y monitor with an unacceptable number of defects will be repaired or replaced
under warranty. This Pixel Policy explains th e different types of pixel defects and defines acceptab le defect levels for
each type. In order to qualify for repair or replacement under warranty, the number of pixel defects on a TFT monitor
panel must exceed these acceptable levels.
Pixels and Sub Pixel Definition
A pixel, or picture element, is composed of three sub pixels in the primary colors of red, green and blue. When all sub
pixels of pixel are lit, the three colored sub pixel together appear as a single white pi xel. When all are dark, the three
colored sub pixels together appear as a single black pixel.
Types of Pixel Defects
• Bright Dot Defects: the m onitor displays a dark pattern, sub pixels or pixels are always lit or “on”
• Black Dot Defects: the monitor displays a light pattern, sub pixels or pixels are always dark or “off”.
ISO 9241-307
Pixel Defect Class
Defect Type 1
Bright Pixel
Defect Type 2
Black Pixel
Defect Type 3
Bright Sub pixel
Defect Type 4 Black
Sub pixel
Class 1 1 1
2
1
0
+
+
+
1
3
5
AOC International (Euro pe) B.V.
62
![](/manual/95/633/bg3f.webp)
Wa r r anty Statement for North & South America (excluding Br azil)
WARRANTY S TATEMENT
for AOC Color Monitors
Including thos e Sold within North America as Specified
Envision Peripherals, Inc. warrants this product to be free from defects in material and workmanship for a period of
three (3) years for parts & labor and one (1) year for CRT Tube or LCD Panel after the original date of consumer
purchase. During this period, EPI ( EPI is the abbreviation of Envision Peripherals, Inc. ) will, at its option, either
repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except
as *stated below. The parts or product that are replaced become the property of EPI.
In the USA to obtain service under this limited warranty, call EPI for the name of the Authorized Service Center
closest to your area. Deliver the product freight pre-paid, along with the dated proof of purchas e, to the EPI
Authorized Service Center. If you cannot deliver the product in person:
Pack it in its origi nal shipping container (or equivalent)
Put the RMA number on the address label
Put the RMA number on the shipping carton
Insure it (or assume the risk of loss/damage during shipment)
Pay all shipping charges
EPI is not res ponsible for damage to inbound product that was not properly packaged.
EPI will pay the return shipment charges within one of the countries specified within this warranty statement. EPI is
not responsible for any costs as s ociated with the transportation of product across international borders. This
includes the international borders of the countries within this warranty statements.
In the United States and Canada contact your Dealer or EPI Customer Service, RMA Department at the toll free
number (888) 662-9888. Or you c an request an RMA Number online at www.aoc.com/na-warranty.
* This limited warranty does not cover any losses or damages that occur as a result of:
Shipping or improper installation or maintenance
Misuse
Neglect
Any cause other than ordinary commercial or industrial application
Adjustment by non-au thor iz ed sour ce
Repair, modification, or installation of options or parts by anyone other than an EPI Authorized Service Center
Improper environment
Excessive or inadequate heating or air conditioning or electrical power failures, surges, or other irregularities
This three-year limited warranty does not cover any of the product's firm ware or hardware that you or any third
party have modified or altered; you bear the sole responsibility and liability for any such modification or alteration.
63
![](/manual/95/633/bg40.webp)
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNES S FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A
PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR AND ONE (1) YEAR FOR CRT TUBE OR LCD PANEL
FROM THE ORIGINAL DATE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSE D OR
IMPLIED) APPLY AFTER THIS PERIOD. IN THE UNITED STATES OF AMERICA, SOME STATES DO NOT
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO T HE ABOVE LIMITATIONS MAY
NOT APPLY TO YOU.
EPI OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY AND EXCLUSIVELY AS STATED HERE .
EPI’ LIABILITY, WHETHER BASED ON CONTRACT, TORT. WARRANTY, STRICT LIABILITY, OR OTHER
THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE
BASIS OF THE CLAIM. IN NO EVENT SHALL ENVISION PERIPHERALS, INC. BE LIABLE FOR ANY LOSS OF
PROFITS, LOSS OF USE OR FACILITIES OR EQUIPMENT OR OTHER INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DA MAGE. IN THE UNITED STATES OF AMERICA, SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDE NTAL OR CONSEQUENTIAL DAMAGES. SO THE ABOVE LIMITATI ON
MAY NOT APPLY TO YOU. ALTHOUGH THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.
YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
In the United States of America, this limited warranty is only valid for Products purchased in the Continental United
States, Alaska, and Hawaii.
Outside the United States of America, this limited warranty is only valid for Products purchased in Canada.
Information in this document is subject to change without notice.
For more details, please visit:
USA: http://us.aoc.com/support/find_service_center
ARGENTINA: http://ar.aoc.com/support/find_service_center
BOLIVIA: http://bo.aoc.com/support/find_service_center
CHILE: http://cl.aoc.com/support/find_service_center
COLOMBIA: http://co.aoc.com/support/find_service_center
COSTA RICA: http://cr.aoc.com/support/find_service_center
DOMINICAN REPUBLIC: http://do.aoc.com/support/find_service_center
ECUADOR: http://ec.aoc.com/support/find_service_center
EL SALVADOR: http://sv.aoc.com/support/find_service_center
GUATEMALA: http://gt.aoc.com/support/find_service_center
HONDURAS: http://hn.aoc.com/support/find_service_center
NICARAGUA: http://ni.aoc.com/support/find_service_center
PANAMA: http://pa.aoc.com/support/find_service_center
PARAGUAY: http://py.aoc.com/support/find_service_center
PERU: http://pe.aoc.com/support/find_service_center
URUGUAY: http://pe.aoc.com/support/find_service_center
VENEZUELA: http://ve.aoc.com/support/find_service_center
IF COUNTRY NOT LISTED: http://latin.aoc.com/support/find_service_center
64
![](/manual/95/633/bg41.webp)
EASE PROGRAME
Only for AOC branded monitors sold within the continental United States.
All A OC branded monitor s are no w covered by the EA SE Program. If you r monitor malfunction s at any time
during the first three months, AOC will provide a replacement monitor within 7 2 hours after you are
approved for our program. If your monitor qualifies for the EASE program, AOC will pay for freight both
ways.
Step 1: Phone our TECH Department at 888.662.9888.
Step 2: Fill out and return EASE registration forms by mail or fax.
Step 3: We will issue a Return Authorization Number upon verification into the program.
Step 4: A monitor will be advance shipped to your location.
Step 5: We will issue a UPS Call Tag to pick up the defective unit.
Step 6: Please review the following chart to see your EASE program qualifications.
WARRANTY
PERIOD
COVERAGE AT
NO CHARGE
CUSTOMER
CHARGES
Within the first three months of
purchase: Covered by EASE
- New AO C monitor - Call tag
dispatched and return freight
charges via UPS
- None*
Between 4 months – 1 Year
- All Parts & Labor Including CRT
Tube & LCD Panel
- UPS Return Freight to AOC
Between 1 Year - 3 Years: Cov er ed
by standard limited warranty
- Parts & Labor (excluding CRT
Tube & LCD Panel)
- UPS Return Freight to AOC
*AOC w ill need to obt a in a cre dit card nu mber if you w ould lik e to get a new AOC monitor ad vanced shipped t o your
location, prior to the defective unit arriving at AOC’s service center. If you do not wish to supply a credit card,
AOC will only ship the new monitor, once the defective unit arrives at the AOC service center.
www.aocmonitor.com
65
![](/manual/95/633/bg42.webp)
TCO DOCUMENT
(FOR TCO CERTIFIED MODELS)
66