About this guide
Chapter 1: Intel® RAID Configuration
- 1.1 Intel® RAID configurations
- 1.2 Installing the RAID controller driver during Windows® 10 OS installation
Chapter 2: AMD RAID Configuration
- 2.1 RAID configurations
- 2.2 Installing the RAID controller driver during Windows® 10 OS installation

ASUS HYPER M.2 X16 CARD V2 User Manual

Displayed below is the user manual for HYPER M.2 X16 CARD V2 by ASUS which is a product in the Interface Cards/Adapters category. This manual has pages.

Related Manuals

ASUS Hyper M.2 x16 Gen 4 Card Manual

ASUS Hyper M.2 x16 Gen 4 Manual

Canon M50 + EF-M 15-45mm f/3.5-6.3 IS STM + EF-M 22mm f/2 STM Manual

Canon M50 + EF-M 15-45mm f/3.5-6.3 IS STM + EF-M 55-200mm f/4.5-6.3 IS STM Manual

RAID

Conguration

Guide

Motherboard

E14794

Revised Edition V4

August 2018

No part of this manual, including the products and software described in it, may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by

any means, except documentation kept by the purchaser for backup purposes, without the express

written permission of ASUSTeK COMPUTER INC. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless

such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the

product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS

OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS

DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,

LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),

EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM

ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR

INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,

AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO

RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN

THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies, and are used only for identication or explanation and to the

owners’ benet, without intent to infringe.

Offer to Provide Source Code of Certain Software

This product contains copyrighted software that is licensed under the General Public License (“GPL”),

under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software

Licenses. Such software in this product is distributed without any warranty to the extent permitted by the

applicable law. Copies of these licenses are included in this product.

Where the applicable license entitles you to the source code of such software and/or other additional

data, you may obtain it for a period of three years after our last shipment of the product, either

(1) for free by downloading it from https://www.asus.com/support/

(2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location

where you want to have it shipped to, by sending a request to:

ASUSTeK Computer Inc.

Legal Compliance Dept.

15 Li Te Rd.,

Beitou, Taipei 112

Taiwan

In your request please provide the name, model number and version, as stated in the About Box of the

product for which you wish to obtain the corresponding source code and your contact details so that we

can coordinate the terms and cost of shipment with you.

The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as

the corresponding binary/object code.

This offer is valid to anyone in receipt of this information.

ASUSTeK is eager to duly provide complete source code as required under various Free Open Source

Software licenses. If however you encounter any problems in obtaining the full corresponding source

code we would be much obliged if you give us a notication to the email address gpl@asus.com, stating

the product and describing the problem (please DO NOT send large attachments such as source code

archives, etc. to this email address).

iii

Contents

About this guide ......................................................................................................... iv

Chapter 1: Intel® RAID Configuration

1.1 Intel® RAID configurations ........................................................................1-5

1.1.1 RAID denitions .......................................................................... 1-5

1.1.2 Installing storage devices ............................................................ 1-5

1.1.3 Intel® Rapid Storage Technology in UEFI BIOS .......................... 1-6

1.1.4 Intel® Virtual Raid on CPU in UEFI BIOS .................................. 1-10

1.1.5 Intel® Rapid Storage Technology Option ROM utility ................ 1-14

1.2 Installing the RAID controller driver during

Windows® 10 OS installation ..................................................................1-19

Chapter 2: AMD RAID Configuration

2.1 RAID configurations ..................................................................................2-1

2.1.1 RAID denitions .......................................................................... 2-1

2.1.2 Installing storage devices ............................................................ 2-2

2.1.3 RaidXpert2 Conguration Utility in UEFI BIOS ........................... 2-2

2.2 Installing the RAID controller driver during

Windows® 10 OS installation ....................................................................2-6

About this guide

This guide contains information that you need to create RAID congurations. You can create

different RAID congurations based on your motherboard chipset and software.

The screenshots in this guide are for reference only. The screenshots may vary with

models, but the congurations steps are similar.

How this guide is organized

This guide contains the following parts:

• Chapter1:Intel® RAID Configuration

This chapter describes the Intel® RAID congurations and lists the setup procedures

to create Intel® RAID congurations.

• Chapter2:AMDRAIDConfiguration

This chapter describes the AMD RAID congurations and lists the setup procedures to

create AMD RAID congurations.

Where to find more information

The ASUS website (www.asus.com) provides updated information on ASUS hardware and

software products.

RAID Conguration Guide 1-5

Intel® RAID Conguration

Chapter 1: Intel® RAID Conguration

1.1 Intel® RAID configurations

If your motherboard supports Intel® Rapid Storage Technology, you can create RAID 0,

RAID 1, RAID 5 or RAID 10 congurations.

Please refer to your motherboard’s user manual for details on the actual supported RAID

congurations.

If you want to install a Windows® operating system to a hard disk drive included in a RAID

set, you have to create a RAID driver disk and load the RAID driver during OS installation.

Refer to section 1.2 Creating a RAID driver disk for details.

1.1.1 RAID definitions

RAID 0 (Data striping) optimizes two identical hard disk drives to read and write data in

parallel, interleaved stacks. Two hard disks perform the same work as a single drive but at a

sustained data transfer rate, double that of a single disk alone, thus improving data access

and storage. Use of two new identical hard disk drives is required for this setup.

RAID 1 (Data mirroring) copies and maintains an identical image of data from one drive to

a second drive. If one drive fails, the disk array management software directs all applications

to the surviving drive as it contains a complete copy of the data in the other drive. This RAID

conguration provides data protection and increases fault tolerance to the entire system.

Use two new drives or use an existing drive and a new drive for this setup. The new drive

must be of the same size or larger than the existing drive.

RAID 5 stripes both data and parity information across three or more hard disk drives.

Among the advantages of RAID 5 conguration include better HDD performance, fault

tolerance, and higher storage capacity. The RAID 5 conguration is best suited for

transaction processing, relational database applications, enterprise resource planning, and

other business systems. Use a minimum of three identical hard disk drives for this setup.

RAID 10 is data striping and data mirroring combined without parity (redundancy data)

having to be calculated and written. With the RAID 10 conguration you get all the benets

of both RAID 0 and RAID 1 congurations. Use four new hard disk drives or use an existing

drive and three new drives for this setup.

1.1.2 Installing storage devices

The motherboard supports Serial ATA hard disk drives and PCIE SSD storage devices. For

optimal performance, install identical drives of the same model and capacity when creating

a disk array.

Refer to Chapter 2 in your motherboard’s user manual for details on installing storage

devices to your motherboard.

1-6 Chapter 1: Intel® RAID Conguration

1.1.3 Intel® Rapid Storage Technology in UEFI BIOS

To enter the Intel® Rapid Storage Technology in UEFI BIOS:

1. Enter the BIOS Setup during POST.

Refer to Chapter 3 in your motherboard’s user manual for details on entering and

navigating through the BIOS Setup.

2. Go to Advanced > PCH Storage Configuration, then set SATA Mode Selection to

[Intel RST Premium With Intel Optane System Acceleration (RAID)].

Due to chipset limitation, when SATA ports are set to RAID mode, all SATA ports run at

RAID mode together.

3. Congure additional settings for your storage device and RAID conguration:

• If you are using SATA storage devices, no additional settings are required.

Please proceed to next step.

• If you are using onboard M.2 cards, go to Advanced > PCH Storage

Configuration, then set all the corresponding M.2 PCIE Storage RAID Support

to [Enabled].

• If you are using Hyper M.2 cards or PCIE SSDs, go to Advanced > CPU

Storage Configuration, then set all the corresponding PCIE slots to [Hyper M.2

X16] or [PCIE X4 SSD Card] accordingly.

The Hyper M.2 card is purchased separately.

4. Go to Boot > CSM (Compatibility Support Module), then set Launch CSM to

[Disabled].

5. Save your changes and exit the BIOS Setup, then enter the BIOS Setup again.

6. Go to the Advanced > Intel(R) Rapid Storage Technology to display the Intel®

Rapid Storage Technology menu.

RAID Conguration Guide 1-7

Creating a RAID set

To create a RAID set:

1. From the Intel® Rapid Storage Technology menu, select Create RAID Volume and

press <Enter>. The following screen appears:

2. When the Name item is selected, enter a name for the RAID set and press <Enter>.

3. When the RAID Level item is selected, press <Enter> to select the RAID level to

create, and then press <Enter>.

4. Under Select Disks, press <Enter> and select X for the disks you want to include in

the RAID set.

1-8 Chapter 1: Intel® RAID Conguration

5. When the Strip Size item is selected, press <Enter> to select strip size for the RAID

array (for RAID 0, 10 and 5 only), and then press <Enter>. The available strip size

values range from 4 KB to 128 KB. The following are typical values:

- RAID 0: 128 KB

- RAID 10: 64 KB

- RAID 5: 64 KB

We recommend a lower strip size for server systems, and a higher strip size for

multimedia computer systems used mainly for audio and video editing.

6. When the Capacity (MB) item is selected, enter the RAID volume capacity that you

want and press <Enter>. The default value indicates the maximum allowed capacity.

7. When the Create Volume item is selected, press <Enter> to create the RAID volume

and return to the Intel® Rapid Storage Technology menu.

RAID Conguration Guide 1-9

Deleting a RAID set

Be cautious when deleting a RAID set. You will lose all data on the hard disk drives when

you delete a RAID set.

To delete a RAID set:

1. From the Intel® Rapid Storage Technology menu, select the RAID volume you want to

delete and press <Enter>. The following screen appears:

2. When the Delete item is selected, press <Enter>, then select Yes to delete the RAID

volume and return to the Intel® Rapid Storage Technology menu, or select No to

cancel.

1-10 Chapter 1: Intel® RAID Conguration

1.1.4 Intel® Virtual Raid on CPU in UEFI BIOS

Some motherboards support Intel® Virtual Raid on CPU with RAID 0, RAID 1, RAID 5, and

RAID 10 solution. RAID 0 can be created without a KEY module, while RAID 1, RAID 5, and

RAID 10 requires a KEY module.

• The KEY module is purchased separately.

• The Hyper M.2 x16 card is purchased separately.

• Due to CPU behavior, CPU RAID functions with Intel® CPU RSTe only supports Intel®

Core™ X-series Processors (6-core or above) and Intel® SSD modules.

• Refer to section Internal connectors in your motherboard’s user manual for the

location of the VROC_HW_KEY connector.

If you plan on using the CPU RAID conguration spanned across different PCIE slots

as OS drives, please install the Hyper M.2 x16 cards into supported PCIE slots. Refer to

section Expansion slots in your motherboard’s user manual for more information on the

PCIE slots.

To enter the Intel® Virtual Raid on CPU in UEFI BIOS:

1. Enter the BIOS Setup during POST.

Refer to Chapter 3 in your motherboard’s user manual for details on entering and

navigating through the BIOS Setup.

2. Go to Boot > CSM (Compatibility Support Module), then set Launch CSM to

[Disabled].

3. Go to the Advanced > CPU Storage Configuration, then set the PCIE slot(s) that

you have installed the Hyper M.2 x16 card(s) or PCIE X4 SSD card(s) to [Hyper M.2

X16] or [PCIE X4 SSD Card] accordingly.

4. Save your changes and exit the BIOS Setup, then enter the BIOS Setup again.

5. Go to the Advanced > Intel(R) Virtual Raid on CPU to display the Intel® Virtual Raid

on CPU menu.

RAID Conguration Guide 1-11

Creating a RAID set

To create a RAID set:

1. From the Intel® Virtual Raid on CPU menu, select Create RAID Volume and press

<Enter>. The following screen appears:

2. When the Name item is selected, enter a name for the RAID set and press <Enter>.

3. When the RAID Level item is selected, press <Enter> to select the RAID level to

create, and then press <Enter>.

4. When the Enable RAID spanned over VMD Controllers item is selected, press

<Enter> and select X to enable this function.

5. Under Select Disks, press <Enter> and select X for the disks you want to include in

the RAID set.

1-12 Chapter 1: Intel® RAID Conguration

6. When the Strip Size item is selected, press <Enter> to select strip size for the RAID

array (for RAID 0, 10 and 5 only), and then press <Enter>. The available strip size

values range from 4 KB to 128 KB. The following are typical values:

- RAID 0: 128 KB

- RAID 10: 64 KB

- RAID 5: 64 KB

We recommend a lower strip size for server systems, and a higher strip size for

multimedia computer systems used mainly for audio and video editing.

7. When the Capacity (MB) item is selected, enter the RAID volume capacity that you

want and press <Enter>. The default value indicates the maximum allowed capacity.

8. When the Create Volume item is selected, press <Enter> to create the RAID volume

and return to the Intel® Rapid Storage Technology menu.

RAID Conguration Guide 1-13

Deleting a RAID set

Be cautious when deleting a RAID set. You will lose all data on the hard disk drives when

you delete a RAID set.

To delete a RAID set:

1. From the Intel® Virtual Raid on CPU menu, select the RAID volume you want to delete

and press <Enter>. The following screen appears:

2. When the Delete item is selected, press <Enter>, then select Yes to delete the RAID

volume and return to the Intel® Virtual Raid on CPU menu, or select No to cancel.

1-14 Chapter 1: Intel® RAID Conguration

1.1.5 Intel® Rapid Storage Technology Option ROM utility

To enter the Intel® Rapid Storage Technology Option ROM utility:

1. Turn on the system.

2. During POST, press <Ctrl> + <I> to display the utility main menu.

The navigation keys at the bottom of the screen allow you to move through the menus

and select the menu options.

The RAID BIOS setup screens shown in this section are for reference only and may not

exactly match the items on your screen.

RAID Volumes:

None defined.

Physical Devices:

Port Device Model Serial # Size Type/Status(Vol ID)

0 ST3160812AS 9LS0HJA4 149.0GB Non-RAID Disk

1 ST3160812AS 9LS0F4HL 149.0GB Non-RAID Disk

2 ST3160812AS 3LS0JYL8 149.0GB Non-RAID Disk

3 ST3160812AS 9LS0BJ5H 149.0GB Non-RAID Disk

RAID Conguration Guide 1-15

Creating a RAID set

To create a RAID set:

1. From the utility main menu, select 1. Create RAID Volume and press <Enter>. The

following screen appears:

2. Enter a name for the RAID set and press <Enter>.

3. When the RAID Level item is selected, press the up/down arrow key to select a RAID

level to create, and then press <Enter>.

4. When the Disks item is selected, press <Enter> to select the hard disk drives you

want to include in the RAID set. The SELECT DISKS screen appears:

Enter a unique volume name that has no special characters

and is 16 characters or less.

[HELP]

Name: Volume 0

RAID Level: aaaaaaaaaaaaaaa

Disks: dssdsdsds

Strip Size:aaaaaaaaaaaaaaaa

Capacity:aaaaaaaaaaaaaa

Sync:aaaaaaaaaa

Create volume

[SELECT DISKS]

Port Device Model Serial # Size Status

0 ST3160812AS 9LS0HJA4 149.0GB Non-RAID Disk

1 ST3160812AS 9LS0F4HL 149.0GB Non-RAID Disk

2 ST3160812AS 3LS0JYL8 149.0GB Non-RAID Disk

3 ST3160812AS 9LS0BJ5H 149.0GB Non-RAID Disk

Select 2 to 6 to use in creating the volume.

[↑↓]-Prev/Next [SPACE]-SelectDisk [ENTER]-Done

1-16 Chapter 1: Intel® RAID Conguration

5. Use the up/down arrow key to select a drive, and then press <Space> to select. A

small triangle marks the selected drive. Press <Enter> after completing your selection.

6. Use the up/down arrow key to select the strip size for the RAID array (for RAID 0, 10

and 5 only), and then press <Enter>. The available strip size values range from 4 KB

to 128 KB. The following are typical values:

- RAID 0: 128 KB

- RAID 10: 64 KB

- RAID 5: 64 KB

We recommend a lower strip size for server systems, and a higher strip size for

multimedia computer systems used mainly for audio and video editing.

7. When the Capacity item is selected, enter the RAID volume capacity that you want

and press <Enter>. The default value indicates the maximum allowed capacity.

8. When the Create Volume item is selected, press <Enter>. The following warning

message appears:

9. Press <Y> to create the RAID volume and return to the main menu, or <N> to go back

to the CREATE VOLUME menu.

WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.

Are you sure you want to create this volume? (Y/N)

RAID Conguration Guide 1-17

Deleting a RAID set

Be cautious when deleting a RAID set. You will lose all data on the hard disk drives when

you delete a RAID set.

To delete a RAID set:

1. From the utility main menu, select 2. Delete RAID Volume and press <Enter>. The

following screen appears:

2. Use the up/down arrow key to select the RAID set you want to delete, and then press

<Delete>. The following warning message appears:

3. Press <Y> to delete the RAID set and return to the utility main menu, or press <N> to

return to the DELETE VOLUME menu.

Deleting a volume will reset the disks to non-RAID.

WARNING: ALL DISK DATA WILL BE DELETED.

(This does not apply to Recovery volumes)

[HELP]

[DELETE VOLUME MENU]

Name Level Drives Capacity Status Bootable

Volume0 RAID0 (Stripe) 2 298.0GB Normal Yes

[↑↓]-Select [ESC]-Previous Menu [DEL]-Delete Volume

ALL DATA IN THE VOLUME WILL BE LOST!

(This does not apply to Recovery volumes)

Are you sure you want to delete “Volume0”? (Y/N):

[DELETE VOLUME VERIFICATION]

1-18 Chapter 1: Intel® RAID Conguration

Exiting the Intel® Rapid Storage Technology Option ROM utility

To exit the utility:

1. From the utility main menu, select 6. Exit, then press <Enter>. The following warning

message appears:

2. Press <Y> to exit or press <N> to return to the utility main menu.

Are you sure you want to exit? (Y/N):

[CONFIRM EXIT]

RAID Conguration Guide 1-19

1.2 Installing the RAID controller driver during

Windows® 10 OS installation

After creating the RAID sets, you are now ready to install an operating system to the

independent drives or bootable array. This part provides the instructions on how to install the

RAID controller drivers during OS installation.

If you plan on using the CPU RAID conguration spanned across different PCIE slots as

OS drives, please install the Hyper M.2 x16 cards to the supported PCIE slots. Refer to

section Expansion slots in your motherboard’s user manual for more information on the

PCIE slots.

To install the RAID controller driver when installing Windows® 10 OS:

1. Boot the computer using the Windows® 10 OS installation disc. Follow the screen

instructions to start installing Windows® 10.

2. When prompted to choose a type of installation, click Custom: Install Windows only

(advanced).

3. Click Load Driver.

1-20 Chapter 2: AMD RAID Conguration

4. A message appears, reminding you to insert the installation media containing the

driver of the RAID controller driver. Click Browse to continue.

• If you have only one optical drive installed in your system, eject the Windows OS

installation disc and replace it with the motherboard Support DVD.

• If you do not have an optical drive, you can use another computer with an optical

drive to copy the RAID driver from the support DVD to a USB ash drive.

5. Locate the driver in the corresponding folder of the Support DVD or the USB ash

drive with RAID driver, then click OK to continue.

6. Select the RAID controller driver you need from the list and click Next.

7. When the system nishes loading the RAID driver, select the drive to install Windows

and click Next.

If you have ejected the Windows OS installation disc in a previous step, ensure to replace

the motherboard Support DVD with the Windows OS installation disc.

8. Setup then proceeds with the OS installation. Follow screen instructions to complete.

RAID Conguration Guide 2-1

AMD RAID Conguration

Chapter 2: AMD RAID Conguration

2.1 RAID configurations

If your motherboard supports RaidXpert2 Conguration Utility, you can create Volume,

RAIDABLE, RAID 0, RAID 1, or RAID 10 (depends on system licensing) congurations.

Please refer to your motherboard’s user manual for details on the actual supported RAID

congurations.

If you want to install a Windows® operating system to a hard disk drive included in a RAID

set, you have to create a RAID driver disk and load the RAID driver during OS installation.

Refer to section 1.2 Creating a RAID driver disk for details.

2.1.1 RAID definitions

Volume provides the ability to link-together storage from one or several disks, regardless

of the size of the space on those disks. This conguration is useful in scavenging space on

disks unused by other disks in the array. This conguration does not provide performance

benets or data redundancy, disk failure will result in data loss.

RAIDABLE arrays (also known as RAID Ready) are a special type of Volume (JBOD) that

allows the user to add more storage space or create a redundant array after a system is

installed. RAIDABLE arrays are created using Option ROM, UEFI, or rcadm.

The ability to create RAIDABLE arrays may vary per system.