Table of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Basic Installation
- Chapter 3: BIOS Setup
- Chapter 4: RAID Support
- Appendix
ASUS ROG Crosshair VIII Hero (WI-FI) User Manual
Displayed below is the user manual for ROG Crosshair VIII Hero (WI-FI) by ASUS which is a product in the Motherboards category. This manual has pages.
Related Manuals
Motherboard
ROG CROSSHAIR
VIII HERO
(WI-FI)
ii
E15378
First Edition
May 2019
Copyright © 2019 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by
any means, except documentation kept by the purchaser for backup purposes, without the express
written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless
such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM
ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN
THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the
owners’ benet, without intent to infringe.
Offer to Provide Source Code of Certain Software
This product contains copyrighted software that is licensed under the General Public License (“GPL”),
under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software
Licenses. Such software in this product is distributed without any warranty to the extent permitted by the
applicable law. Copies of these licenses are included in this product.
Where the applicable license entitles you to the source code of such software and/or other additional
data, you may obtain it for a period of three years after our last shipment of the product, either
(1) for free by downloading it from https://www.asus.com/support/
or
(2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location
where you want to have it shipped to, by sending a request to:
ASUSTeK Computer Inc.
Legal Compliance Dept.
15 Li Te Rd.,
Beitou, Taipei 112
Taiwan
In your request please provide the name, model number and version, as stated in the About Box of the
product for which you wish to obtain the corresponding source code and your contact details so that we
can coordinate the terms and cost of shipment with you.
The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as
the corresponding binary/object code.
This offer is valid to anyone in receipt of this information.
ASUSTeK is eager to duly provide complete source code as required under various Free Open Source
Software licenses. If however you encounter any problems in obtaining the full corresponding source
code we would be much obliged if you give us a notication to the email address gpl@asus.com, stating
the product and describing the problem (please DO NOT send large attachments such as source code
archives, etc. to this email address).
iii
Contents
Safety information ...................................................................................................... vi
About this guide ........................................................................................................ vii
ROG CROSSHAIR VIII HERO (WI-FI) specifications summary ............................... ix
Package contents ...................................................................................................... xv
Installation tools and components ......................................................................... xvi
Chapter 1: Product Introduction
1.1 Motherboard overview ...............................................................................1-1
1.1.1 Before you proceed .....................................................................1-1
1.1.2 Motherboard layout ..................................................................... 1-2
1.1.3 Central Processing Unit (CPU) ...................................................1-4
1.1.4 System memory ..........................................................................1-5
1.1.5 Expansion slots ........................................................................... 1-7
1.1.6 Onboard buttons .........................................................................1-9
1.1.7 Onboard switches .....................................................................1-11
1.1.8 Onboard jumpers ......................................................................1-12
1.1.9 Onboard LEDs ..........................................................................1-13
1.1.10 Internal connectors....................................................................1-16
1.2 ProbeIt .......................................................................................................1-29
Chapter 2: Basic Installation
2.1 Building your PC system ...........................................................................2-1
2.1.1 CPU installation...........................................................................2-1
2.1.2 Cooling system installation..........................................................2-2
2.1.3 Motherboard installation ..............................................................2-5
2.1.4 DIMM installation.........................................................................2-7
2.1.5 ATX power connection ................................................................ 2-8
2.1.6 SATA device connection ............................................................. 2-9
2.1.7 Front I/O connector ...................................................................2-10
2.1.8 Expansion card installation .......................................................2-11
2.1.9 M.2 installation ..........................................................................2-12
2.1.10 Wi-Fi antenna installation ..........................................................2-14
2.2 BIOS update utility ................................................................................... 2-15
2.3 Motherboard rear and audio connections .............................................2-16
2.3.1 Rear I/O connection ..................................................................2-16
2.3.2 Audio I/O connections ............................................................... 2-18
2.4 Starting up for the first time ....................................................................2-20
2.5 Turning off the computer ........................................................................2-20
iv
Chapter 3: BIOS Setup
3.1 Knowing BIOS ............................................................................................3-1
3.2 BIOS setup program ..................................................................................3-2
3.2.1 Advanced Mode ..........................................................................3-3
3.2.2 EZ Mode......................................................................................3-6
3.2.3 Q-Fan Control .............................................................................3-7
3.2.4 EZ Tuning Wizard .......................................................................3-9
3.3 My Favorites .............................................................................................3-11
3.4 Main menu ................................................................................................3-13
3.5 Extreme Tweaker menu ...........................................................................3-13
3.6 Advanced menu .......................................................................................3-14
3.6.1 AMD fTPM conguration ........................................................... 3-14
3.6.2 CPU Conguration ....................................................................3-15
3.6.3 SATA Conguration ..................................................................3-15
3.6.4 Onboard Devices Conguration ................................................ 3-16
3.6.5 APM Conguration .................................................................... 3-18
3.6.6 PCI Subsystem Settings ...........................................................3-18
3.6.7 USB Conguration ....................................................................3-19
3.6.8 HDD/SSD SMART Information .................................................3-19
3.6.9 Network Stack Conguration.....................................................3-19
3.6.10 AMD CBS .................................................................................3-20
3.6.11 AMD PBS ................................................................................. 3-20
3.7 Monitor menu ...........................................................................................3-20
3.8 Boot menu ................................................................................................3-21
3.9 Tool menu ................................................................................................. 3-22
3.9.1 ASUS EZ Flash 3 Utility ............................................................3-22
3.9.2 ASUS Secure Erase..................................................................3-23
3.9.3 ASUS User Prole.....................................................................3-24
3.9.4 ASUS SPD Information ............................................................. 3-24
3.9.5 Graphics Card Information ........................................................ 3-24
3.9.6 ASUS Armoury Crate ................................................................ 3-25
3.10 Exit menu .................................................................................................. 3-25
3.11 Updating BIOS ..........................................................................................3-26
3.11.1 EZ Update ................................................................................. 3-26
3.11.2 ASUS EZ Flash 3 ...................................................................... 3-27
3.11.3 ASUS CrashFree BIOS 3 ..........................................................3-29
v
Chapter 4: RAID Support
4.1 AMD RAID Array configurations ...............................................................4-1
4.1.1 RAID denitions ..........................................................................4-1
Appendix
Q-Code table ............................................................................................................ A-1
Notices .................................................................................................................... A-5
ASUS contact information .................................................................................... A-11
vi
Safety information
Electrical safety
• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet
before relocating the system.
• When adding or removing devices to or from the system, ensure that the power cables
for the devices are unplugged before the signal cables are connected. If possible,
disconnect all power cables from the existing system before you add a device.
• Before connecting or removing signal cables from the motherboard, ensure that all
power cables are unplugged.
• Seek professional assistance before using an adapter or extension cord. These devices
could interrupt the grounding circuit.
• Ensure that your power supply is set to the correct voltage in your area. If you are not
sure about the voltage of the electrical outlet you are using, contact your local power
company.
• If the power supply is broken, do not try to x it by yourself. Contact a qualied service
technician or your retailer.
Operation safety
• Before installing the motherboard and adding devices on it, carefully read all the
manuals that came with the package.
• Before using the product, ensure all cables are correctly connected and the power
cables are not damaged. If you detect any damage, contact your dealer immediately.
• To avoid short circuits, keep paper clips, screws, and staples away from connectors,
slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Do not place the product in any area
where it may become wet.
• Place the product on a stable surface.
• If you encounter technical problems with the product, contact a qualied service
technician or your retailer.
vii
About this guide
This user guide contains the information you need when installing and conguring the
motherboard.
How this guide is organized
This guide contains the following parts:
• Chapter1:ProductIntroduction
This chapter describes the features of the motherboard and the new technology it
supports. It includes description of the switches, jumpers, and connectors on the
motherboard.
• Chapter2:BasicInstallation
This chapter lists the hardware setup procedures that you have to perform when
installing system components.
• Chapter3:BIOSSetup
This chapter tells how to change system settings through the BIOS Setup menus.
Detailed descriptions of the BIOS parameters are also provided.
• Chapter4:RAIDSupport
This chapter describes the RAID congurations.
Where to find more information
Refer to the following sources for additional information and for product and software
updates.
1. ASUS website
The ASUS website (www.asus.com) provides updated information on ASUS hardware
and software products.
2. Optional documentation
Your product package may include optional documentation, such as warranty yers,
that may have been added by your dealer. These documents are not part of the
standard package.
viii
Conventions used in this guide
To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying to
complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
NOTE: Tips and additional information to help you complete a task.
Typography
Bold text Indicates a menu or an item to select.
Italics
Used to emphasize a word or a phrase.
<Key> Keys enclosed in the less-than and greater-than sign
means that you must press the enclosed key.
Example: <Enter> means that you must press the Enter
or Return key.
<Key1> + <Key2> + <Key3> If you must press two or more keys simultaneously, the
key names are linked with a plus sign (+).
ix
ROG CROSSHAIR VIII HERO (WI-FI)
specifications summary
CPU
AMD AM4 Socket for 3rd and 2nd Gen AMD Ryzen™ / 2nd and 1st
Gen AMD Ryzen™ with Radeon™ Vega Graphics Processors*
* Refer to www.asus.com for the AMD CPU support list.
Chipset AMD X570
Memory
3rd Gen AMD Ryzen™ Processors
4 x DIMM, max. 128GB, DDR4 4600+(O.C.) / 4533(O.C.) /
4400(O.C.) / 4266(O.C.) / 4133(O.C.) / 4000(O.C.) / 3866(O.C.) /
3733(O.C.) / 3600(O.C.) / 3466(O.C.) / 3200(O.C.) / 3000(O.C.)
/ 2933(O.C.) / 2800(O.C.) / 2666 / 2400 / 2133 MHz non-ECC,
un-buffered memory
2nd Gen AMD Ryzen™ Processors
4 x DIMM, max. 64GB, DDR4 3600(O.C.) / 3466(O.C.) /
3200(O.C.) / 3000(O.C.) / 2933(O.C.) / 2800(O.C) / 2666 / 2400 /
2133 MHz non-ECC, un-buffered memory
2nd and 1st Gen AMD Ryzen™ with Radeon™ Vega Graphics
Processors
4 x DIMM, max. 64GB, DDR4 3200(O.C.) / 3000(O.C.) /
2933(O.C.) / 2800(O.C) / 2666 / 2400 / 2133 MHz non-ECC, un-
buffered memory
Dual channel memory architecture
* Refer to www.asus.com for the Memory QVL (Qualified Vendors List).
Expansion slots
3rd Gen AMD Ryzen™ Processors
- 2 x PCIe 4.0 x16 SafeSlots (supports x16, x8/x8)
2nd Gen AMD Ryzen™ Processors
- 2 x PCIe 3.0 x16 SafeSlots (supports x16, x8/x8)
2nd and 1st Gen AMD Ryzen™ with Radeon™ Vega Graphics
Processors
- 1 x PCIe 3.0 x16 SafeSlot (supports x8)
AMD X570 chipset
- 1 x PCIe 4.0 x16 (supports x4)
- 1 x PCIe 4.0 x1
Multi-GPU
3rd and 2nd Gen AMD Ryzen™ Processors
Supports NVIDIA® 2-Way SLI® Technology
Supports AMD 3-Way CrossFireX™ Technology
2nd and 1st Gen AMD Ryzen™ with Radeon™ Vega Graphics
Processors
Supports AMD 2-Way CrossFireX™ Technology
(continued on the next page)
x
ROG CROSSHAIR VIII HERO (WI-FI)
specifications summary
Storage
3rd Gen AMD Ryzen™ Processors
- 1 x M.2 Socket 3 with M Key, type 2242 / 2260 / 2280
(PCIE 4.0 x4 and SATA modes) storage devices support
2nd Gen AMD Ryzen™ / 2nd and 1st Gen AMD Ryzen™ with
Radeon™ Vega Graphics Processors
- 1 x M.2 Socket 3 with M Key, type 2242 / 2260 / 2280
(PCIE 3.0 x4 and SATA modes) storage devices support
AMD X570 chipset
- 8 x SATA 6Gb / s ports
- Support Raid 0, 1, 10
- 1 x M.2 Socket 3 with M Key, type 2242 / 2260 / 2280 / 22110
(PCIE 4.0 x4 and SATA modes) storage devices support
LAN
Realtek RTL8125-CG 2.5G LAN
Intel® Ethernet Controller I211-AT
Anti-surge LANGuard
ROG GameFirst Technology
Wireless Data Network
Intel® Wi-Fi 6 AX200
2 x 2 Wi-Fi 6 (802.11 a/b/g/n/ac/ax) with MU-MIMO supports dual
frequency band 2.4/5GHz
Supports channel bandwidth: HT20/HT40/HT80/HT160
Up to 2.4Gbps transfer speed
Bluetooth Bluetooth v5.0
Audio
ROG SupremeFX 8-Channel High Definition Audio CODEC
S1220
- Supports up to 32-Bit/192kHz playback*
- High quality 120 dB SNR stereo playback output and 113 dB
SNR recording input
- Impedance sense for front and rear headphone outputs
- ESS® ES9023P High Denition DAC
- SupremeFX Shielding Technology
- Jack-detection, Multi-streaming, and Front Panel Jack-retasking
- Optical S/PDIF out port at back Panel
Audio Features:
- Sonic Radar III
- Sonic Studio III + Sonic Studio Virtual Mixer
* Due to limitations in HDA bandwidth, 32-Bit/192kHz is not supported
for 8-Channel audio.
(continued on the next page)
xi
USB
3rd Gen AMD Ryzen™ Processors
- 4 x USB 3.2 Gen 2 ports (4 ports at back panel, Type-A [red])
2nd Gen AMD Ryzen™ / 2nd and 1st Gen AMD Ryzen™ with
Radeon™ Vega Graphics Processors
- 4 x USB 3.2 Gen 1 ports (4 ports at back panel, Type-A [red])
AMD X570 chipset
- 1 x USB 3.2 Gen 2 front panel connector
- 4 x USB 3.2 Gen 2 ports (4 ports at back panel, 3 x Type-A [red],
1 x Type-C)
- 6 x USB 3.2 Gen 1 ports (4 ports at back panel [blue], 2 ports at
front panel)
- 4 x USB 2.0 ports at front panel
ROG Exclusive Features
Extreme Engine Digi+
- MicroFine Alloy Choke
- 10K Black Metallic Capacitors
- IR3555 PoweIRstage®
ROG Extreme OC kit:
- Safe Boot button
- Slow Mode
- LN2 Mode
- OptiMem III
Extreme Tweaker
ROG Exclusive Software
- RAMCache III
- ROG RAMDisk
- CPU-Z
- GameFirst V
- Sonic Studio III + Sonic Studio Virtual Mixer
- Sonic Radar III
(continued on the next page)
ROG CROSSHAIR VIII HERO (WI-FI)
specifications summary
xii
ROG CROSSHAIR VIII HERO (WI-FI)
specifications summary
Special Features
ASUS Exclusive Software Features
- Armoury Crate
- AURA
- ASUS Dual Intelligent Processors 5
- 5-way Optimization tuning key perfectly consolidates TPU
Insights, EPU Guidance, DIGI+ VRM, Fan Expert 4, and Turbo
app
- AI Suite 3
- ASUS EZ DIY
- ASUS CrashFree BIOS 3
- ASUS EZ Flash 3
- ASUS C.P.R. (CPU Parameter Recall)
- Ai Charger
ASUS Exclusive Hardware Features
- ROG patented pre-mounted I/O shield
- ASUS NODE: hardware control interface
- USB BIOS Flashback™ Button
- Clear CMOS Button
- Start Button
- Reset Button
- ReTry button
ASUS Q-Design
- Q-Code
- Q-Slot
- Q-Connector
- Q-LED
- Q-DIMM
Back I/O Ports
1 x Clear CMOS button
1 x BIOS Flashback™ button
1 x 2x2 Wi-Fi Module
8 x USB 3.2 Gen 2 ports ( 1 x Type-C and 7 x Type-A [red] )
4 x USB 3.2 Gen 1 ports [blue]
1 x Anti-surge 2.5G LAN (RJ45) port
1 x Anti-surge LAN (RJ45) port
1 x Optical S/PDIF out
5 x Gold-plated audio jacks
(continued on the next page)
xiii
ROG CROSSHAIR VIII HERO (WI-FI)
specifications summary
Internal connectors
1 x USB 3.2 Gen 2 front panel connector
1 x USB 3.2 Gen 1 header supports additional 2 USB 3.2 Gen 1
ports
2 x USB 2.0 headers supports additional 4 USB 2.0 ports
1 x NODE connector
8 x SATA 6Gb/s connectors
1 x M.2 Socket 3 for M Key, type 2242/2260/2280 storage devices
support
1 x M.2 Socket 3 for M Key, type 2242/2260/2280/22110 storage
devices support
1 x 4-Pin CPU_Fan connector
1 x 4-Pin CPU_OPT fan connector
3 x 4-Pin CHA_Fan connectors
1 x 4-Pin AIO_PUMP connector
1 x 4-Pin W_PUMP+ connector
1 x 4-Pin H_AMP fan connector
1 x 4-Pin PCH_FAN connector
1 x 3-Pin W_FLOW connector
1 x 2-Pin W_IN connector
1 x 2-Pin W_OUT connector
1 x T_SENSOR connector
1 x 24-pin EATX power connector
1 x 8-pin EATX 12V power connector
1 x 4-pin EATX 12V power connector
1 x Start button
1 x Reset button
1 x Safe Boot button
1 x Retry button
1 x LN2 mode jumper
1 x Slow mode switch
1 x System panel connector
1 x Speaker connector
1 x Front panel audio connector (AAFP)
1 x TPM connector
2 x Aura Addressable Gen 2 headers
2 x Aura RGB headers
(continued on the next page)
xiv
BIOS 256 Mb Flash ROM, UEFI AMI BIOS, PnP, WfM2.0, SM BIOS 3.2,
ACPI 6.2
Manageability WOL, PXE
Software
Overwolf
WinRAR
Anti-virus software (1-year full subscription)
Operating System Windows® 10 64-bit
Form Factor ATX Form Factor, 12“ x 9.6” (30.5cm x 24.4cm)
Specications are subject to change without notice.
ROG CROSSHAIR VIII HERO (WI-FI)
specifications summary
xv
Package contents
Check your motherboard package for the following items.
Motherboard 1 x ROG CROSSHAIR VIII HERO (WI-FI) motherboard
Cables
1 x 4-in-1 SATA 6Gb/s cable
1 x Extension Cable for RGB strip
1 x Extension Cable for RGB addressable strip
Accessories
1 x ASUS 2x2 dual band Wi-Fi antenna
1 x Q-Connector
1 x 2-in-1 M.2 screws package
Application DVD 1 x ROG motherboard support DVD
Documentation 1 x User guide
Others
1 x ROG coaster
1 x ROG sticker
1 x ROG thank you card
1 x Cablemod coupon
If any of the above items is damaged or missing, contact your retailer.
xvi
Installation tools and components
1 Bag of screws Phillips (cross) screwdriver
PC chassis Power supply unit
AMD AM4 CPU AMD AM4/AM3 compatible CPU Fan
DDR4 DIMM SATA hard disk drive
SATA optical disc drive (optional) Graphics card
The tools and components in the table above are not included in the motherboard
package.
ROG CROSSHAIR VIII HERO (WI-FI) 1-1
Chapter 1
Product Introduction
1
Chapter 1: Product Introduction
1.1 Motherboard overview
1.1.1 Before you proceed
Take note of the following precautions before you install motherboard components or
change any motherboard settings.
Components shown in this section may require additional purchase. Refer to Package
contents section for more information about the contents of your motherboard package.
• Unplugthepowercordfromthewallsocketbeforetouchinganycomponent.
• Beforehandlingcomponents,useagroundedwriststraportouchasafelygrounded
objectorametalobject,suchasthepowersupplycase,toavoiddamagingthemdue
to static electricity.
• HoldcomponentsbytheedgestoavoidtouchingtheICsonthem.
• Wheneveryouuninstallanycomponent,placeitonagroundedantistaticpadorin
the bag that came with the component.
• Beforeyouinstallorremoveanycomponent,ensurethattheATXpowersupplyis
switched off or the power cord is detached from the power supply. Failure to do so
maycauseseveredamagetothemotherboard,peripherals,orcomponents.
1-2 Chapter 1: Product Introduction
Chapter 1
Refer to Internal connectors and Rear panel features section for more information.
1.1.2 Motherboard layout
ROG CROSSHAIR VIII HERO (WI-FI) 1-3
Chapter 1
Layout contents Page
1. Power connectors 1-23
2. CPUsocket 1-4
3. DIMMslots 1-5
4. Fan and Pump connectors 1-21
5. Q-Code LED 1-15
6. RGBLEDconnector 1-25
7. AddressableGen2LEDconnector 1-26
8. Power button 1-9
9. Reset button 1-9
10. ProbeIt 1-29
11. USB3.2Gen2connector 1-18
12. PCHFanconnector 1-27
13. USB3.2Gen1connector 1-19
14. SATA6Gb/sconnector 1-16
15. WaterCoolingSystemconnectors 1-22
16. SystemPanelconnector 1-24
17. ThermalSensorconnector 1-22
18. SlowModeswitch 1-11
19. USB2.0connector 1-20
20. Node connector 1-28
21. TPMconnector 1-28
22. ReTry button 1-10
23. SafeBootbutton 1-10
24. LN2Modejumper 1-12
25. FrontPanelAudioconnector 1-18
26. M.2slot 1-17
27. RearI/OCoverLEDconnector 1-27
1-4 Chapter 1: Product Introduction
Chapter 1
1.1.3 Central Processing Unit (CPU)
ThemotherboardcomeswithanAM4socketdesignedforAMDAM4Socketfor3rd and
2ndGenAMDRyzen™/2nd and 1stGenAMDRyzen™withRadeon™VegaGraphics
Processors.
• TheAM4sockethasadifferentpinoutdesign.EnsurethatyouuseaCPUdesigned
fortheAM4socket.
• TheCPUtsinonlyonecorrectorientation.DONOTforcetheCPUintothesocket
topreventbendingtheconnectorsontheCPUanddamagingtheCPU.
• EnsurethatallpowercablesareunpluggedbeforeinstallingtheCPU.
ROG CROSSHAIR VIII HERO (WI-FI) 1-5
Chapter 1
1.1.4 System memory
ThemotherboardcomeswithDualInlineMemoryModules(DIMM)slotsdesignedforDDR4
(DoubleDataRate4)memorymodules.
ADDR4memorymoduleisnotcheddifferentlyfromaDDR,DDR2,orDDR3module.DO
NOTinstallaDDR,DDR2,orDDR3memorymoduletotheDDR4slot.
Recommended memory configurations
1-6 Chapter 1: Product Introduction
Chapter 1
Memory configurations
Youmayinstall2GB,4GB,8GB,16GB,and32GBunbufferedandnon‑ECCDDR4
DIMMsintotheDIMMsockets.
YoumayinstallvaryingmemorysizesinChannelAandChannelB.Thesystemmaps
thetotalsizeofthelower‑sizedchannelforthedual‑channelconguration.Anyexcess
memoryfromthehigher‑sizedchannelisthenmappedforsingle‑channeloperation.
• ThedefaultmemoryoperationfrequencyisdependentonitsSerialPresenceDetect
(SPD),whichisthestandardwayofaccessinginformationfromamemorymodule.
Underthedefaultstate,somememorymodulesforoverclockingmayoperateata
lowerfrequencythanthevendor‑markedvalue.
• Forsystemstability,useamoreefcientmemorycoolingsystemtosupportafull
memoryloadoroverclockingcondition.
• AlwaysinstalltheDIMMSwiththesameCASLatency.Foranoptimumcompatibility,
werecommendthatyouinstallmemorymodulesofthesameversionordatacode
(D/C)fromthesamevendor.Checkwiththevendortogetthecorrectmemory
modules.
• VisittheASUSwebsiteforthelatestQVL.
ROG CROSSHAIR VIII HERO (WI-FI) 1-7
Chapter 1
1.1.5 Expansion slots
Unplugthepowercordbeforeaddingorremovingexpansioncards.Failuretodosomay
cause you physical injury and damage motherboard components.
Slot No. Slot Description
1PCIex16_1
2PCIex16_2
3PCIex1
4PCIex16_3
1-8 Chapter 1: Product Introduction
Chapter 1
PCIe operating mode
3rd Gen AMD Ryzen™ Processors
Slot Description
PCIe operating mode
Single VGA /
PCIe card
Dual VGA /
PCIe card
Triple VGA /
PCIe card
PCIex16_1 x16(PCIe4.0) x8(PCIe4.0) x8(PCIe4.0)
PCIex16_2 N/A x8(PCIe4.0) x8(PCIe4.0)
PCIex16_3 N/A N/A x4(PCIe4.0)
M.2_1(PCIeMode) x4(PCIe4.0) x4(PCIe4.0) x4(PCIe4.0)
M.2_1(SATAMode) Support Support Support
M.2_2(PCIeMode) x4(PCIe4.0) x4(PCIe4.0) x4(PCIe4.0)
M.2_2(SATAMode) Support Support Support
2nd Gen AMD Ryzen™ Processors
Slot Description
PCIe operating mode
Single VGA /
PCIe card
Dual VGA /
PCIe card
Triple VGA /
PCIe card
PCIex16_1 x16(PCIe3.0) x8(PCIe3.0) x8(PCIe3.0)
PCIex16_2 N/A x8(PCIe3.0) x8(PCIe3.0)
PCIex16_3 N/A N/A x4(PCIe4.0)
M.2_1(PCIeMode) x4(PCIe3.0) x4(PCIe3.0) x4(PCIe3.0)
M.2_1(SATAMode) Support Support Support
M.2_2(PCIeMode) x4(PCIe4.0) x4(PCIe4.0) x4(PCIe4.0)
M.2_2(SATAMode) Support Support Support
2nd and 1st Gen AMD Ryzen™ with Radeon™ Vega Graphics
Slot Description
PCIe operating mode
Single VGA /
PCIe card
Dual VGA /
PCIe card
Triple VGA /
PCIe card
PCIex16_1 x8(PCIe3.0) x8(PCIe3.0) N/A
PCIex16_2 N/A N/A N/A
PCIex16_3 N/A x4(PCIe4.0) N/A
M.2_1(PCIeMode) x4(PCIe3.0) x4(PCIe3.0) x4(PCIe3.0)
M.2_1(SATAMode) Support Support Support
M.2_2(PCIeMode) x4(PCIe4.0) x4(PCIe4.0) x4(PCIe4.0)
M.2_2(SATAMode) Support Support Support
• WerecommendthatyouprovidesufcientpowerwhenrunningCrossFireX™orSLI®
mode.
• Ensuretoconnectthe8‑pinand4‑pinpowerplugswhenrunningCrossFireX™or
SLI® mode.
• Connectachassisfantothechassisfanconnectorswhenusingmultiplegraphics
cardsforbetterthermalenvironment.
ROG CROSSHAIR VIII HERO (WI-FI) 1-9
Chapter 1
1.1.6 Onboard buttons
1. Power button
PressthePowerbuttontopowerupthesystem,orputthesystemintosleeporsoft‑
offmode(dependingontheoperatingsystemsettings).
Thebuttonalsolightsupwhenthesystemispluggedtoapowersource,indicating
thatyoushouldshutdownthesystemandunplugthepowercablebeforeremovingor
installing any motherboard component.
2. Reset button
Press the Reset button to reboot the system.
1-10 Chapter 1: Product Introduction
Chapter 1
3. Safe Boot button
TheSafeBootbuttontemporarilyappliessafesettingstotheBIOSwhileretainingthe
overclockedsettings,allowingyoutomodifythesettingscausingabootfailure.Press
thisbuttonatanytimetoforcethesystemtorebootintotheBIOSsafemode.
4. ReTry button
TheReTrybuttonisspeciallydesignedforoverclockersandismostusefulduring
the booting process where the Reset button is rendered useless. Press this button
to force the system to reboot while retaining the same settings to be retried in quick
successiontoachieveasuccessfulPOST.
ROG CROSSHAIR VIII HERO (WI-FI) 1-11
Chapter 1
1.1.7 Onboard switches
1. Slow Mode switch
ThesystemmaycrashduetotheCPUbeingunstablewhenusingextreme
overclockingsettings.EnabletheSlowModeswitchduringLN2benchingtodecrease
theprocessorfrequencyandstabilizethesystem,allowingyoutokeeptrackofthe
overclockingdata.
1-12 Chapter 1: Product Introduction
Chapter 1
1.1.8 Onboard jumpers
1. LN2 Mode jumper
Settopins2‑3tooptimizethemotherboardtoremedythecold‑bootbugduringPOST
and help the system boot successfully.
ROG CROSSHAIR VIII HERO (WI-FI) 1-13
Chapter 1
1.1.9 Onboard LEDs
1. Q LEDs
TheQLEDscheckkeycomponents(CPU,DRAM,VGA,andbootingdevices)during
themotherboardbootingprocess.Ifanerrorisfound,thecriticalcomponent’sLED
stayslitupuntiltheproblemissolved.
TheQLEDsprovidethemostprobablecauseofanerrorcodeasastartingpointfor
troubleshooting.Theactualcausemayvaryfromcasetocase.
2. CPU Status LED
TheCPUStatusLEDwillindicatethecurrentstatusofyourCPU.Aredlightindicates
thattheCPUisnotreadytoboot,andtheLEDwillturnoffoncetheproblemissolved.
EnsuretheCPUStatusLEDisoffbeforepoweringonyoursystem.
1-14 Chapter 1: Product Introduction
Chapter 1
3. Storage Device Activity LED
TheStorageDeviceActivityLEDlightsuporblinkswhendataisreadfromorwritten
tothestoragedeviceorstoragedeviceadd‑oncard.
4. 8-pin Power Plug LED
The 8-pin Power Plug LED lights up to indicate that the 8-pin power plug is not
connected.
• DONOTconnectthe4‑pinpowerplugonly,themotherboardmayoverheatunder
heavyusage.
• Ensuretoconnectthe8‑pinpowerplug,orconnectboththe8‑pinand4‑pinpower
plugs.
ROG CROSSHAIR VIII HERO (WI-FI) 1-15
Chapter 1
5. Q-Code LED
TheQ‑CodeLEDdesignprovidesyouwitha2‑digiterrorcodethatdisplaysthe
system status.
• TheQ‑CodeLEDsprovidethemostprobablecauseofanerrorcodeasastarting
pointfortroubleshooting.Theactualcausemayvaryfromcasetocase.
• PleaserefertotheQ‑CodetableintheAppendix section for more details.
1-16 Chapter 1: Product Introduction
Chapter 1
1.1.10 Internal connectors
1. SATA 6Gb/s connector
TheSATA6Gb/sconnectorallowsyoutoconnectSATAdevicessuchasopticaldisc
drivesandharddiskdrivesviaaSATAcable.
IfyouinstalledSATAstoragedevices,youcancreateaRAID0,1,and10conguration
throughtheonboardAMDX570chipset.
• Theseconnectorsaresetto[AHCI]bydefault.IfyouintendtocreateaSerialATA
RAIDsetusingtheseconnectors,settheSATAModeSelectionitemintheBIOSto
[RAID].
• BeforecreatingaRAIDset,refertotheRAID Configuration Guide. You can
download the RAID Configuration GuidefromtheASUSwebsite.
ROG CROSSHAIR VIII HERO (WI-FI) 1-17
Chapter 1
2. M.2 slot
TheM.2slotallowsyoutoinstallM.2devicessuchasM.2SSDmodules.
• For3rdGenAMDRyzen™Processors,theM.2_1supportsPCIe4.0x4andSATA
modesMkeydesignandtype2242/2260/2280storagedevices.
• For2ndGenAMDRyzen™/2nd and 1stGenAMDRyzen™withRadeon™Vega
GraphicsProcessors,theM.2_1supportsPCIe3.0x4andSATAmodesMkey
designandtype2242/2260/2280storagedevices.
• ForAMDX570chipset,theM.2_2supportsPCIe4.0x4andSATAmodesMkey
designandtype2242/2260/2280/22110storagedevices.
TheM.2SSDmoduleispurchasedseparately.
1-18 Chapter 1: Product Introduction
Chapter 1
4. USB 3.2 Gen 2 connector
TheUSB3.2Gen2connectorallowsyoutoconnectaUSB3.2Gen2modulefor
additionalUSB3.2Gen2ports.TheUSB3.2Gen2connectorprovidesdatatransfer
speedsofupto10Gb/s.
TheUSB3.2Gen2moduleispurchasedseparately.
3. Front Panel Audio connector
Thefrontpanelaudioconnectorisforachassis‑mountedfrontpanelaudioI/Omodule
thatsupportsHDAudio.ConnectoneendofthefrontpanelaudioI/Omodulecableto
this connector.
Werecommendthatyouconnectahigh‑denitionfrontpanelaudiomoduletothis
connectortoavailofthemotherboard’shigh‑denitionaudiocapability.
ROG CROSSHAIR VIII HERO (WI-FI) 1-19
Chapter 1
5. USB 3.2 Gen 1 connector
TheUSB3.2Gen1connectorallowsyoutoconnectaUSB3.2Gen1modulefor
additionalUSB3.2Gen1ports.TheUSB3.2Gen1connectorprovidesdatatransfer
speedsofupto5Gb/s.
TheUSB3.2Gen1moduleispurchasedseparately.
ThepluggedUSB3.2Gen1devicemayrunonxHCIorEHCImodedependingonthe
operatingsystem’ssetting.
1-20 Chapter 1: Product Introduction
Chapter 1
6. USB 2.0 connector
TheUSB2.0connectorallowsyoutoconnectaUSBmoduleforadditionalUSB
2.0ports.TheUSB2.0connectorprovidesdatatransferspeedsofupto480MB/s
connection speed.
DONOTconnecta1394cabletotheUSBconnectors.Doingsowilldamagethe
motherboard!
TheUSB2.0moduleispurchasedseparately.
ROG CROSSHAIR VIII HERO (WI-FI) 1-21
Chapter 1
7. Fan and Pump connectors
The Fan and Pump connectors allow you to connect fans or pumps to cool the
system.
• DONOTforgettoconnectthefancablestothefanconnectors.Insufcientair
owinsidethesystemmaydamagethemotherboardcomponents.Thesearenot
jumpers! Do not place jumper caps on the fan connectors!
• Ensurethecableisfullyinsertedintotheconnector.
• Forwatercoolingkits,connectthepumptotheW_PUMP+connector,andconnect
thefanstotheCPU_FANandCPU_OPTconnectors.
• ForAll‑In‑Onecoolers,connectthepumptotheAIO_PUMPconnector,andconnect
thefanstotheCPU_FANandCPU_OPTconnectors.
• ForbetterQ‑Fanfunctions,werecommendusing4‑pinPWMfanswhenyouconnect
powerfulfans(1Aorabove)ontotheH_AMP_FANconnector.
• EnsuretodisableQ‑Fanfunctionsifyouwanttoconnectpowerful3‑pinDCfans(1A
orabove)ontotheH_AMP_FANconnector.
Header Max. Current Max. Power Default Speed Shared Control
CPU_FAN 1A 12W Q-Fan Controlled A
CPU_OPT 1A 12W Q-Fan Controlled A
CHA_FAN1 1A 12W Q-Fan Controlled -
CHA_FAN2 1A 12W Q-Fan Controlled -
CHA_FAN3 1A 12W Q-Fan Controlled -
H_AMP 3A 36W Q-Fan Controlled -
AIO_PUMP 1A 12W Full‑Speed -
W_PUMP+ 3A 36W Full‑Speed -
1-22 Chapter 1: Product Introduction
Chapter 1
9. Thermal Sensor connector
TheThermalSensorconnectorallowsyoutoconnectasensortomonitorthe
temperatureofthedevicesandthecriticalcomponentsinsidethemotherboard.
Connectthethermalsensorandplaceitonthedeviceorthemotherboard’s
component to detect its temperature.
The thermal sensor is purchased separately.
8. Water Cooling System connectors
TheWaterCoolingSystemconnectorsallowyoutoconnectsensorstomonitorthe
temperatureandowrateofyourwatercoolingsystem.Youcanmanuallyadjustthe
fansandwaterpumptooptimizethethermalefciencyofyourwatercoolingsystem.
ROG CROSSHAIR VIII HERO (WI-FI) 1-23
Chapter 1
10. Power connectors
These Power connectors allow you to connect your motherboard to a power supply.
Thepowersupplyplugsaredesignedtotinonlyoneorientation,ndtheproper
orientationandpushdownrmlyuntilthepowersupplyplugsarefullyinserted.
• DONOTconnectthe4‑pinpowerplugonly,themotherboardmayoverheatunder
heavyusage.
• Ensuretoconnectthe8‑pinpowerplug,orconnectboththe8‑pinand4‑pinpower
plugs.
• Forafullyconguredsystem,werecommendthatyouuseapowersupplyunit
(PSU)thatcomplieswithATX12VSpecication2.0(orlaterversion)andprovidesa
minimumpowerof350W.
• WerecommendthatyouuseaPSUwithahigherpoweroutputwhenconguringa
systemwithmorepower‑consumingdevices.Thesystemmaybecomeunstableor
may not boot up if the power is inadequate.
• Ifyouwanttousetwoormorehigh‑endPCIExpressx16cards,useaPSUwith
1000Wpowerorabovetoensurethesystemstability.
1-24 Chapter 1: Product Introduction
Chapter 1
11. System Panel connector
TheSystemPanelconnectorsupportsseveralchassis‑mountedfunctions.
• SystemPowerLEDconnector(PLED)
The2‑pinconnectorallowsyoutoconnecttheSystemPowerLED.TheSystem
PowerLEDlightsupwhenthesystemisconnectedtoapowersource,orwhenyou
turnonthesystempower,andblinkswhenthesystemisinsleepmode.
• StorageDeviceActivityLEDconnector(HD_LED)
The2‑pinconnectorallowsyoutoconnecttheStorageDeviceActivityLED.The
StorageDeviceActivityLEDlightsuporblinkswhendataisreadfromorwrittentothe
storagedeviceorstoragedeviceadd‑oncard.
• SystemWarningSpeakerconnector(SPEAKER)
The 4-pin connector allows you to connect the chassis-mounted system warning
speaker. The speaker allows you to hear system beeps and warnings.
• PowerButton/Soft-offButtonconnector(PWRBTN)
The 3-1 pin connector allows you to connect the system power button. Press the
powerbuttontopowerupthesystem,orputthesystemintosleeporsoft‑offmode
(dependingontheoperatingsystemsettings).
• Resetbuttonconnector(RESET)
The 2-pin connector allows you to connect the chassis-mounted reset button. Press
the reset button to reboot the system.
ROG CROSSHAIR VIII HERO (WI-FI) 1-25
Chapter 1
12. RGB LED connector
TheRGBLEDconnectorallowsyoutoconnectRGBLEDstrips.
TheRGBLEDconnectorsupports5050RGBmulti‑colorLEDstrips(12V/G/R/B),witha
maximumpowerratingof3A(12V),andnolongerthan3m.
Beforeyouinstallorremoveanycomponent,ensurethatthepowersupplyisswitchedoff
orthepowercordisdetachedfromthepowersupply.Failuretodosomaycausesevere
damagetothemotherboard,peripherals,orcomponents.
• ActuallightingandcolorwillvarywithLEDstrip.
• IfyourLEDstripdoesnotlightup,checkiftheRGBLEDextensioncableandthe
RGBLEDstripisconnectedinthecorrectorientation,andthe12Vconnectoris
alignedwiththe12Vheaderonthemotherboard.
• TheLEDstripwillonlylightupwhenthesystemispoweredon.
• TheLEDstripispurchasedseparately.
1-26 Chapter 1: Product Introduction
Chapter 1
13. Addressable Gen2 LED connector
TheAddressableGen2LEDconnectorallowsyoutoconnectindividuallyaddressable
RGBWS2812BLEDstripsorWS2812BbasedLEDstrips.
TheAddressableRGBLEDconnectorsupportsWS2812BaddressableRGBLEDstrips
(5V/Data/Ground),withamaximumpowerratingof3A(5V)andamaximumof120LEDs.
Beforeyouinstallorremoveanycomponent,ensurethatthepowersupplyisswitchedoff
orthepowercordisdetachedfromthepowersupply.Failuretodosomaycausesevere
damagetothemotherboard,peripherals,orcomponents.
• ActuallightingandcolorwillvarywithLEDstrip.
• IfyourLEDstripdoesnotlightup,checkiftheaddressableRGBLEDstripis
connectedinthecorrectorientation,andthe5Vconnectorisalignedwiththe5V
header on the motherboard.
• TheaddressableRGBLEDstripwillonlylightup when the system is powered on.
• TheaddressableRGBLEDstripispurchasedseparately.
ROG CROSSHAIR VIII HERO (WI-FI) 1-27
Chapter 1
14. Rear I/O Cover LED connector
TheRearI/OCoverLEDconnectorisforconnectingtheLEDsonyourrearI/Ocover.
15. PCH Fan connector
ThePCHFanconnectorisforconnectingthePCHfanonyourPCHcover.
1-28 Chapter 1: Product Introduction
Chapter 1
16. TPM connector
TheTPMconnectorallowsyoutoconnectaTrustedPlatformModule(TPM).ATPM
securelystoreskeys,digitalcerticates,passwords,data,andalsohelpsenhance
networksecurity,protectdigitalidentities,andensuresplatformintegrity.
TheTPMispurchasedseparately.
17. Node connector
TheNodeconnectorallowsyoutoconnectNodecompatibledevices.
Visitwww.asus.comformoreinformationaboutthedevicesandthelatestcompatibilitylist.
ROG CROSSHAIR VIII HERO (WI-FI) 1-29
Chapter 1
1.2 ProbeIt
TheROGProbeItallowsyoutodetectyoursystem’scurrentvoltageandOCsettingsusing
amultimeter.YoucanalsomeasuretheProbeItpointsduringoverclocking.
Using ProbeIt
Connect one of the probe onto the GNDProbeItpoint,thenconnecttheotherprobeonto
anotherProbeItpointtomeasurethecorrespondingvoltageinformation.
Theillustrationaboveisforreferenceonly,theactualmotherboardlayoutandmeasure
points may differ by model.
1-30 Chapter 1: Product Introduction
Chapter 1
ROG CROSSHAIR VIII HERO (WI-FI) 2-1
Chapter 2
Basic Installation
2
2.1 Building your PC system
The diagrams in this section are for reference only. The motherboard layout may vary with
models, but the installation steps are the same for all models.
Chapter 2: Basic Installation
2.1.1 CPU installation
The AMD AM4 socket is compatible with AMD AM4 processors. Ensure you use a CPU
designed for the AM4 socket. The CPU ts in only one correct orientation. DO NOT force
the CPU into the socket to prevent bending the connectors on the socket and damaging
the CPU!
2-2 Chapter 2: Basic Installation
Chapter 2
CPU heatsink and fan assembly Type 1
2.1.2 Cooling system installation
Apply the Thermal Interface Material to the CPU
cooling system and CPU before you install the
cooling system, if necessary.
ROG CROSSHAIR VIII HERO (WI-FI) 2-3
Chapter 2
CPU heatsink and fan assembly Type 2
When using this type of CPU fan, remove the screws and the retention module only. Do
not remove the plate on the bottom.
2-4 Chapter 2: Basic Installation
Chapter 2
To install an AIO cooler
AIO_PUMP
CPU_OPT
CPU_FAN
ROG CROSSHAIR VIII HERO (WI-FI) 2-5
Chapter 2
1. Place the motherboard into the chassis, ensuring that its rear I/O ports are aligned to
the chassis’ rear I/O panel.
2.1.3 Motherboard installation
2. Remove the screws that secure the PCH cover (A), then remove the PCH cover (B).
3. Remove the screws that secure the M.2 heatsink (A), then remove the M.2 heatsink (B).
2-6 Chapter 2: Basic Installation
Chapter 2
4. Place nine (9) screws into the holes indicated by circles to secure the motherboard to
the chassis.
DO NOT over tighten the screws! Doing so can damage the motherboard.
ROG CROSSHAIR VIII HERO (WI-FI) 2-7
Chapter 2
2.1.4 DIMM installation
To remove a DIMM
2-8 Chapter 2: Basic Installation
Chapter 2
2.1.5 ATX power connection
OR AND
• DO NOT connect the 4-pin power plug only, the motherboard may overheat under
heavy usage.
• Ensure to connect the 8-pin power plug, or connect both the 8-pin and 4-pin power
plugs.
ROG CROSSHAIR VIII HERO (WI-FI) 2-9
Chapter 2
2.1.6 SATA device connection
OR
2-10 Chapter 2: Basic Installation
Chapter 2
2.1.7 Front I/O connector
USB 3.2 Gen 2
To install USB 3.2 Gen 2 connectorTo install ASUS Q-Connector
This connector will only t in one
orientation. Push the connector until it
clicks into place.
USB 2.0
AAFP
To install USB 2.0 connector
To install front panel audio connector
USB 3.2 Gen 1
To install USB 3.2 Gen 1 connector
To install system speaker connector
ROG CROSSHAIR VIII HERO (WI-FI) 2-11
Chapter 2
2.1.8 Expansion card installation
To install PCIe x16 cards
To install PCIe x1 cards
2-12 Chapter 2: Basic Installation
Chapter 2
2.1.9 M.2 installation
Supported M.2 type varies per motherboard.
For type 2280 M.2 on M.2_1 socket For type 2242 / 2260 M.2 on M.2_1 socket
The M.2 is purchased separately.
1
1
2
3
3
4
5
6
8
8
7
10
10
9
1
1
2
3
3
4
5
6
7
8
10
10
9
12
12
11
ROG CROSSHAIR VIII HERO (WI-FI) 2-13
Chapter 2
For type 2242 / 2260 / 2280 M.2 on M.2_2 socketFor type 22110 M.2 on M.2_2 socket
The M.2 is purchased separately.
1
3
1
2
4
5
6
6
1
3
1
2
4
6
5
7
8
8
2-14 Chapter 2: Basic Installation
Chapter 2
• Ensure that the ASUS 2x2 dual band Wi-Fi antenna is securely installed to the Wi-Fi
ports.
• Ensure that the antenna is at least 20 cm away from all persons.
The illustration above is for reference only. The I/O port layout may vary with models, but
the Wi-Fi antenna installation procedure is the same for all models.
2.1.10 Wi-Fi antenna installation
Installing the ASUS 2x2 dual band W-Fi antenna
Connect the bundled ASUS 2x2 dual band Wi-Fi antenna connector to the Wi-Fi ports at the
back of the chassis.
ROG CROSSHAIR VIII HERO (WI-FI) 2-15
Chapter 2
2.2 BIOS update utility
USB BIOS Flashback
USB BIOS Flashback allows you to easily update the BIOS without entering the existing
BIOS or operating system. Simply insert a USB storage device to the USB port, press the
USB BIOS Flashback button for three seconds, and the BIOS is updated automatically.
To use USB BIOS Flashback:
1. Insert a USB storage device to the USB Flashback port.
We recommend you to use a USB 2.0 storage device to save the latest BIOS version for
better compatibility and stability.
2. Visit https://www.asus.com/support/ and download the latest BIOS version for this
motherboard.
3. Rename the le as C8HW.CAP, then copy it to your USB storage device.
4. Shut down your computer.
5. Press the BIOS Flashback button for three seconds until the Flashback LED blinks
three times, indicating that the BIOS Flashback function is enabled.
• Do not unplug portable disk, power system, or press the CLR_CMOS button while
BIOS update is ongoing, otherwise update will be interrupted. In case of interruption,
please follow the steps again.
• If the light ashes for ve seconds and turns into a solid light, this means that
the BIOS Flashback is not operating properly. This may be caused by improper
installation of the USB storage device and lename/le format error. If this scenario
happens, please restart the system to turn off the light.
• Updating BIOS may have risks. If the BIOS program is damaged during the process
and results to the system’s failure to boot up, please contact your local ASUS Service
Center.
For more BIOS update utilities in BIOS setup, refer to the section 3.11 Updating BIOS in
Chapter 3.
6. Wait until the light goes out, indicating that the BIOS updating process is completed.
USB BIOS Flashback button USB BIOS Flashback port
2-16 Chapter 2: Basic Installation
Chapter 2
2.3 Motherboard rear and audio connections
2.3.1 Rear I/O connection
Rear panel connectors
1. Clear CMOS button. Press this button to clear the BIOS setup information only
when the system hangs due to overclocking.
2. USB 3.2 Gen 1 ports E1 and E2
3. USB 3.2 Gen 1 ports E3 and E4
4. 2.5G LAN (RJ-45) port*
5. LAN (RJ-45) port*
6. USB BIOS Flashback™ button
7. Wi-Fi 802.11 a/b/g/n/ac/ax, Bluetooth V5.0
8. USB 3.2 Gen 2 Type-A ports 1 and 2
9. USB 3.2 Gen 2 Type-A ports 3 and 4
10. USB 3.2 Gen 2 Type-A ports 6 and 7
11. USB 3.2 Gen 2 Type-A port 8
12. USB 3.2 Gen 2 Type-C™ port C9
13. Optical S/PDIF OUT port
14. Audio I/O ports**
* and ** : Refer to the tables on the next page for LAN port LEDs, and audio port definitions.
• USB 3.2 Gen 1/Gen 2 devices can only be used as data storage only.
• We strongly recommend that you connect your devices to ports with matching
data transfer rate. Please connect your USB 3.2 Gen 1 devices to USB 3.2 Gen 1
ports and your USB 3.2 Gen 2 devices to USB 3.2 Gen 2 ports for faster and better
performance for your devices.
ROG CROSSHAIR VIII HERO (WI-FI) 2-17
Chapter 2
** Audio 2, 4, 5.1 or 7.1-channel configuration
Port Headset
2-channel 4-channel 5.1-channel 7.1-channel
Light Blue Line In Line In Line In Side Speaker Out
Lime Line Out Front Speaker Out Front Speaker Out Front Speaker Out
Pink Mic In Mic In Mic In Mic In
Orange – – Center/Sub
woofer
Center/Sub woofer
Black – Rear Speaker Out Rear Speaker Out Rear Speaker Out
* LAN ports LED indications
Activity Link LED Speed LED
Status Description Status Description
OFF No link OFF 10 Mbps connection
ORANGE Linked ORANGE 100 Mbps connection
BLINKING Data activity GREEN 1 Gbps connection
Activity Link LED Speed LED
Status Description Status Description
OFF No link OFF 100 Mbps connection
GREEN Linked GREEN 2.5 Gbps connection
Blinkinga
BLINKING Data activity ORANGE 1 Gbps / 100 Mbps /
10 Mbps connection
ACT/LINK
LED SPEED
LED
LAN port
ACT/LINK
LED SPEED
LED
LAN port
Realtek RTL8125-CG 2.5G LAN port LED indications
2-18 Chapter 2: Basic Installation
Chapter 2
2.3.2 Audio I/O connections
Audio I/O ports
Connect to Headphone and Mic
Connect to Stereo Speakers
Connect to 2-channel Speakers
ROG CROSSHAIR VIII HERO (WI-FI) 2-19
Chapter 2
Connect to 4-channel Speakers
Connect to 5.1-channel Speakers
Connect to 7.1-channel Speakers
2-20 Chapter 2: Basic Installation
Chapter 2
2.4 Starting up for the first time
1. After making all the connections, replace the system case cover.
2. Ensure that all switches are off.
3. Connect the power cord to the power connector at the back of the system chassis.
4. Connect the power cord to a power outlet that is equipped with a surge protector.
5. Turn on the devices in the following order:
a. Monitor
b. External SCSI devices (starting with the last device on the chain)
c. System power
6. After applying power, the system power LED on the system front panel case lights
up. For systems with ATX power supplies, the system LED lights up when you press
the ATX power button. If your monitor complies with the “green” standards or if it has
a “power standby” feature, the monitor LED may light up or change from orange to
green after the system LED turns on.
The system then runs the power-on self tests (POST). While the tests are running,
the BIOS beeps (refer to the BIOS beep codes table) or additional messages appear
on the screen. If you do not see anything within 30 seconds from the time you turned
on the power, the system may have failed a power-on test. Check the jumper settings
and connections or call your retailer for assistance.
BIOS Beep Description
One short beep
VGA detected
Quick boot set to disabled
No keyboard detected
One continuous beep followed by two
short beeps then a pause (repeated) No memory detected
One continuous beep followed by three
short beeps No VGA detected
One continuous beep followed by four
short beeps Hardware component failure
7. At power on, hold down the <Delete> key to enter the BIOS Setup. Follow the
instructions in Chapter 3.
2.5 Turning off the computer
While the system is ON, press the power button for less than four seconds to put the system
on sleep mode or soft-off mode, depending on the BIOS setting. Press the power button
for more than four seconds to let the system enter the soft-off mode regardless of the BIOS
setting.
ROG CROSSHAIR VIII HERO (WI-FI) 3-1
Chapter 3
BIOS Setup
3
Chapter 3: BIOS Setup
3.1 Knowing BIOS
The new ASUS UEFI BIOS is a Unied Extensible Interface that complies with UEFI
architecture, offering a user-friendly interface that goes beyond the traditional keyboard-
only BIOS controls to enable a more exible and convenient mouse input. You can easily
navigate the new UEFI BIOS with the same smoothness as your operating system. The
term “BIOS” in this user manual refers to “UEFI BIOS” unless otherwise specied.
BIOS (Basic Input and Output System) stores system hardware settings such as storage
device conguration, overclocking settings, advanced power management, and boot
device conguration that are needed for system startup in the motherboard CMOS. In
normal circumstances, the default BIOS settings apply to most conditions to ensure
optimal performance. DO NOT change the default BIOS settings except in the following
circumstances:
• An error message appears on the screen during the system bootup and requests you to
run the BIOS Setup.
• You have installed a new system component that requires further BIOS settings or
update.
Inappropriate BIOS settings may result to instability or boot failure. We strongly
recommend that you change the BIOS settings only with the help of a trained
service personnel.
When downloading or updating the BIOS le, rename it as C8HW.CAP for this
motherboard.
3-2 Chapter 3: BIOS Setup
Chapter 3
• The BIOS setup screens shown in this section are for reference purposes only, and
may not exactly match what you see on your screen.
• Ensure that a USB mouse is connected to your motherboard if you want to use the
mouse to control the BIOS setup program.
• If the system becomes unstable after changing any BIOS setting, load the default
settings to ensure system compatibility and stability. Select the Load Optimized
Defaults item under the Exit menu or press hotkey <F5>. See section 3.10 Exit
Menu for details.
• If the system fails to boot after changing any BIOS setting, try to clear the CMOS and
reset the motherboard to the default value. See section 2.3.1 Rear I/O connection
for information on how to erase the RTC RAM via the Clear CMOS button.
• The BIOS setup program does not support the Bluetooth devices.
Please visit ASUS website for the detailed BIOS content manual.
BIOS menu screen
The BIOS Setup program can be used under two modes: EZ Mode and Advanced Mode.
You can change modes from Setup Mode in Boot menu or by pressing the <F7> hotkey.
3.2 BIOS setup program
Use the BIOS Setup to update the BIOS or congure its parameters. The BIOS screen
include navigation keys and brief onscreen help to guide you in using the BIOS Setup
program.
Entering BIOS at startup
To enter BIOS Setup at startup, press <Delete> or <F2> during the Power-On Self Test
(POST). If you do not press <Delete> or <F2>, POST continues with its routines.
Entering BIOS Setup after POST
To enter BIOS Setup after POST:
• Press <Ctrl>+<Alt>+<Delete> simultaneously.
• Press the reset button on the system chassis.
• Press the power button to turn the system off then back on. Do this option only if you
failed to enter BIOS Setup using the rst two options.
After doing either of the three options, press <Delete> key to enter BIOS.
ROG CROSSHAIR VIII HERO (WI-FI) 3-3
Chapter 3
3.2.1 Advanced Mode
The Advanced Mode provides advanced options for experienced end-users to congure
the BIOS settings. The gure below shows an example of the Advanced Mode. Refer to the
following sections for the detailed congurations.
The default screen for entering the BIOS setup program can be changed. Refer to the
Setup Mode item in section Boot menu for details.
Menu items General help
Menu bar Language Qfan Control(F6)
MyFavorite(F3) EZ Tuning Wizard(F11) AURA ON/OFF(F4)
Search(F9)
Scroll bar
Pop-up Menu
Configuration fields
Last modified settings Go back to EZ Mode Hot Keys
Displays a quick overview
of the system status
Search on the FAQ
3-4 Chapter 3: BIOS Setup
Chapter 3
Menu bar
The menu bar on top of the screen has the following main items:
My Favorites For saving the frequently-used system settings and conguration.
Main For changing the basic system conguration
Extreme Tweaker For changing the overclocking settings
Advanced For changing the advanced system settings
Monitor For displaying the system temperature, power status, and changing
the fan settings.
Boot For changing the system boot conguration
Tool For conguring options for special functions
Exit For selecting the exit options and loading default settings
Menu items
The highlighted item on the menu bar displays the specic items for that menu. For example,
selecting Main shows the Main menu items.
The other items (My Favorites, Ai Tweaker, Advanced, Monitor, Boot, Tool, and Exit) on the
menu bar have their respective menu items.
Submenu items
A greater than sign (>) before each item on any menu screen means that the item has a
submenu. To display the submenu, select the item and press <Enter>.
Language
This button above the menu bar contains the languages that you can select for your BIOS.
Click this button to select the language that you want to display in your BIOS screen.
My Favorites(F3)
This button above the menu bar shows all BIOS items in a Tree Map setup. Select
frequently-used BIOS settings and save it to MyFavorites menu.
Refer to section 3.3 My Favorites for more information.
Q-Fan Control(F6)
This button above the menu bar displays the current settings of your fans. Use this button to
manually tweak the fans to your desired settings.
Refer to section 3.2.3 QFan Control for more information.
EZ Tuning Wizard(F11)
This button above the menu bar allows you to view and tweak the overclocking settings of
your system. It also allows you to change the motherboard’s SATA mode from AHCI to RAID
mode.
Refer to section 3.2.4 EZ Tuning Wizard for more information.
ROG CROSSHAIR VIII HERO (WI-FI) 3-5
Chapter 3
Search (F9)
This button allows you to search for BIOS items by entering its name, enter the item name to
nd the related item listing.
AURA (F4)
This button allows you to turn the RGB LED lighting or functional LED on or off.
[All On] All RGB LEDs and Functional LEDs will be enabled.
[Stealth Mode] All RGB LEDs and Functional LEDs will be disabled.
[Aura Only] RGB LEDs will be enabled, Functional LEDs will be disabled.
[Aura Off] Functional LEDs will be enabled, RGB LEDs will be disabled.
Search on FAQ
Move your mouse over this button to show a QR code, scan this QR code on your mobile
device to connect to the BIOS FAQ web page of the ASUS support website. You can also
scan the following QR code:
Scroll bar
A scroll bar appears on the right side of a menu screen when there are items that do not t
on the screen. Press the Up/Down arrow keys or <Page Up> / <Page Down> keys to display
the other items on the screen.
General help
At the bottom of the menu screen is a brief description of the selected item. Use <F12> key
to capture the BIOS screen and save it to the removable storage device.
Configuration fields
These elds show the values for the menu items. If an item is user-congurable, you can
change the value of the eld opposite the item. You cannot select an item that is not
user-congurable.
A congurable eld is highlighted when selected. To change the value of a eld, select it and
press <Enter> to display a list of options.
Hot keys
This button contains the navigation keys for the BIOS setup program. Use the navigation
keys to select items in the menu and change the settings.
Last Modified button
This button shows the items that you last modied and saved in BIOS Setup.
3-6 Chapter 3: BIOS Setup
Chapter 3
3.2.2 EZ Mode
The EZ Mode provides you an overview of the basic system information, and allows you to
select the display language, system performance, mode and boot device priority. To access
the Advanced Mode, select Advanced Mode or press the <F7> hotkey for the advanced
BIOS settings.
To switch from Advanced Mode to EZ Mode, click EZ Mode(F7) or press the <F7> hotkey.
The boot device options vary depending on the devices you installed to the system.
Selects the display language
of the BIOS setup program
Displays a quick overview
of the system status
Displays the system properties of the selected mode.
Click < or > to switch EZ System Tuning modes
Loads optimized
default settings
Creates storage RAID and
configures system overclocking
Displays the CPU Fan’s speed. Click
the button to manually tune the fans
Saves the changes
and resets the system
Click to display boot devices
Selects the boot device priority
Click to go to Advanced mode
Search on the FAQ
Search(F9) AURA ON/OFF(F4)
ROG CROSSHAIR VIII HERO (WI-FI) 3-7
Chapter 3
3.2.3 Q-Fan Control
The QFan Control allows you to set a fan prole or manually congure the operating speed
of your CPU and chassis fans.
Click to select a fan to be
configured Click to activate
PWM Mode
Click to undo the
changes
Click to apply the fan setting
Click to go back to main menu
Select a profile to
apply to your fans
Click to activate DC Mode
Select to manually configure
your fans
3-8 Chapter 3: BIOS Setup
Chapter 3
Configuring fans manually
Select Manual from the list of proles to manually congure your fans’ operating speed.
To congure your fans:
1. Select the fan that you want to congure and to view its current status.
2. Click and drag the speed points to adjust the fans’ operating speed.
3. Click Apply to save the changes then click Exit (ESC).
Speed points Select to manually
configure your fans
ROG CROSSHAIR VIII HERO (WI-FI) 3-9
Chapter 3
3.2.4 EZ Tuning Wizard
EZ Tuning Wizard allows you to easily overclock your CPU and DRAM, computer usage,
and CPU fan to their best settings.
OC Setup
OC Tuning
To start OC Tuning:
1. Press <F11> on your keyboard or click from the BIOS screen to
open EZ Tuning Wizard screen.
2. Click OC
then click Next.
3. Select a PC scenario Daily Computing or Gaming/Media Editing, then click Next.
3-10 Chapter 3: BIOS Setup
Chapter 3
4. Select a Main Cooling System BOX cooler, Tower cooler, Water cooler, or I’m not
sure, then click Next.
5. After selecting the Main Cooling System, click Next then click Yes to start the OC
Tuning.
ROG CROSSHAIR VIII HERO (WI-FI) 3-11
Chapter 3
3.3 My Favorites
My Favorites is your personal space where you can easily save and access your favorite
BIOS items.
My Favorites comes with several performance, power saving, and fast boot related items by
default. You can personalize this screen by adding or removing items.
3-12 Chapter 3: BIOS Setup
Chapter 3
Adding items to My Favorites
To add BIOS items:
1. Press <F3> on your keyboard or click from the BIOS screen to open
Setup Tree Map screen.
2. On the Setup Tree Map screen, select the BIOS items that you want to save in My
Favorites screen.
3. Select an item from main menu panel, then click the submenu that you want to save
as favorite from the submenu panel and click or press <Enter> on your keyboard.
You cannot add the following items to My Favorite items:
• Items with submenu options
• User-managed items such as language and boot order
• Conguration items such as Memory SPD Information, system time and date.
4. Click Exit (ESC) or press <Esc> key to close Setup Tree Map screen.
5. Go to My Favorites menu to view the saved BIOS items.
Main menu panel
Submenu panel
Selected shortcut
items
Delete all favorite
items
Recover to default
favorite items
ROG CROSSHAIR VIII HERO (WI-FI) 3-13
Chapter 3
3.4 Main menu
The Main menu screen appears when you enter the Advanced Mode of the BIOS Setup
program. The Main menu provides you an overview of the basic system information, and
allows you to set the system date, time, language, and security settings.
Security
The Security menu items allow you to change the system security settings.
• If you have forgotten your BIOS password, erase the CMOS Real Time Clock
(RTC) RAM to clear the BIOS password. See section 1.1.6 Onboard buttons and
switches for information on how to erase the RTC RAM via the Clear CMOS button.
• The Administrator or User Password items on top of the screen show the default [Not
Installed]. After you set a password, these items show [Installed].
3.5 Extreme Tweaker menu
The Extreme Tweaker menu items allow you to congure overclocking-related items.
Be cautious when changing the settings of the Extreme Tweaker menu items. Incorrect
eld values can cause the system to malfunction
The conguration options for this section vary depending on the CPU and DIMM model
you installed on the motherboard.
Ai Overclock Tuner
Allows you to select the CPU overclocking options to achieve the desired CPU internal
frequency. Conguration options:
[Auto] Loads the optimal settings for the system.
[Default] Loads the default settings for the system.
[Manual] Allows you to individually set overclocking parameters.
The following item appears only when you set the Ai Overclocking Tuner to [Manual].
BCLK Frequency
This item allows you to set the BCLK frequency to enhance the system performance.
Use the <+> or <-> to adjust the value.
We recommend you to set the value based on the CPU specication, as high BCLK
frequencies may damage the CPU permanently.
3-14 Chapter 3: BIOS Setup
Chapter 3
Memory Frequency
This item allows you to set the memory operating frequency. The congurable options vary
with the BCLK (base clock) frequency setting. Select the auto mode to apply the optimized
setting.
Conguration options: [Auto] [DDR4-1333MHz] - [DDR4-5000MHz]
TPU
This item allows you to automatically overclock the CPU and DRAM frequencies and voltage
for an enhanced system performance.
[Keep Current Settings] Keep the current settings without changing anything.
[TPU I] Applies air cooling overclocking conditions.
[TPU II] Applies water cooling overclocking conditions.
Ensure to use water cooling device before selecting [TPU II].
3.6 Advanced menu
The Advanced menu items allow you to change the settings for the CPU and other system
devices.
Be cautious when changing the settings of the Advanced menu items. Incorrect eld
values can cause the system to malfunction.
3.6.1 AMD fTPM configuration
The items in this menu show the AMD fTPM conguration options.
TPM Device Selection
This item allows you to enable or disable AMD CPU fTPM.
Conguration options: [Firmware TPM] [Discrete TPM]
When Firmware TPM is set to disabled all saved data on it will be lost.
ROG CROSSHAIR VIII HERO (WI-FI) 3-15
Chapter 3
PSS Support
This item allows you enable or disable the generation of ACPI_PPC, _PSS, and _PCT
objects.
Conguration options: [Disabled] [Enabled] [Auto]
NX Mode
This item allows you enable or disable no-execute page protection function.
Conguration options: [Disabled] [Enabled]
SVM Mode
This item allows you enable or disable CPU virtualization.
Conguration options: [Disabled] [Enabled]
3.6.2 CPU Configuration
The items in this menu show the CPU-related information that the BIOS automatically
detects.
The items in this menu may vary based on the CPU installed.
3.6.3 SATA Configuration
While entering Setup, the BIOS automatically detects the presence of SATA devices. The
SATA Port items show Not Present if no SATA device is installed to the corresponding
SATA port.
SATA0 Enable
This item allows you to enable or disable the SATA Device.
Conguration options: [Disabled] [Enabled]
SATA1 Enable
This item allows you to enable or disable the SATA Device.
Conguration options: [Disabled] [Enabled]
SATA Mode
This item allows you to set the SATA conguration.
[AHCI] Set to [AHCI] when you want the SATA hard disk drives to use the
AHCI (Advanced Host Controller Interface). The AHCI allows the
onboard storage driver to enable advanced Serial ATA features that
increases storage performance on random workloads by allowing
the drive to internally optimize the order of commands.
[RAID] Set to [RAID] when you want to create a RAID conguration from
the SATA hard disk drives.
3-16 Chapter 3: BIOS Setup
Chapter 3
SMART Self Test
S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a monitoring system
that shows a warning message during POST (Power-on Self Test) when an error occurs in
the hard disks.
Conguration options: [On] [Off]
SATA6G_1(Gray) - SATA6G_8(Gray)
SATA6G_1 - SATA6G_8
This item allows you to enable or disable the selected SATA port.
Conguration options: [Disabled] [Enabled]
Hot Plug
These items appears only when the SATA Mode is set to [AHCI] and allows you to
enable or disable SATA Hot Plug Support.
Conguration options: [Disabled] [Enabled]
3.6.4 Onboard Devices Configuration
The items in this menu allow you to switch between PCIe Lanes and congure onboard
devices.
HD Audio Controller
This item allows you to use the Azalia High Denition Audio Controller
Conguration options: [Disabled] [Enabled]
PCIEX16_2 Bandwidth
[X8 Mode] Run at x8 mode.
[PCIe RAID Mode] Run at x4+x4 mode to create a RAID array for up to 2 PCIE
devices.
Use [PCIe RAID Mode] only when installing the Hyper M.2 x16 card or other M.2 adapter
cards. Installing other devices when using this mode may cause your PC to fail to boot.
RGB LED lighting
When system is in working state
[All On] All RGB LEDs and Functional LEDs will be enabled.
[Stealth Mode] All RGB LEDs and Functional LEDs will be disabled.
[Aura Only] RGB LEDs will be enabled, Functional LEDs will be disabled.
[Aura Off] Functional LEDs will be enabled, RGB LEDs will be disabled.
Q-Code LED Function
[Disabled] Q-Code LED will be disabled.
[POST Code Only] Show POST (Power-On Self-Test) code and CPU temperature
on the Q-Code LED.
[Auto] Show POST (Power-On Self-Test) code on the Q-Code LED.
ROG CROSSHAIR VIII HERO (WI-FI) 3-17
Chapter 3
When system is in sleep, hibernate or soft off states
[All On] All RGB LEDs and Functional LEDs will be enabled.
[Stealth Mode] All RGB LEDs and Functional LEDs will be disabled.
[Aura Only] RGB LEDs will be enabled, Functional LEDs will be disabled.
[Aura Off] Functional LEDs will be enabled, RGB LEDs will be disabled.
Realtek 2.5G LAN Controller
This item allows you to enable or disable the Realtek 2.5G LAN Controller.
Conguration options: [On] [Off]
Intel LAN Controller
This item allows you to enable or disable the Intel LAN controller.
Conguration options: [On] [Off]
Wi-Fi 6 (802.11ax) Controller
This item allows you to enable or disable the Wi-Fi 6 (802.11ax) Controller.
Conguration options: [Disabled] [Enabled]
Bluetooth Controller
This item allows you to enable or disable the Intel Bluetooth controller.
Conguration options: [Disabled] [Enabled]
PCIEX16/X8_1 Mode
This item allows you to set the link speed for PCIEX16/X8_1 slot.
Conguration options: [Auto] [GEN 1] [GEN 2] [GEN 3] [GEN 4]
PCIEX8/X4_2 Mode
This item allows you to set the link speed for PCIEX8/X4_2 slot.
Conguration options: [Auto] [GEN 1] [GEN 2] [GEN 3] [GEN 4]
PCIEX4_3 Mode
This item allows you to set the link speed for PCIEX4_3 slot.
Conguration options: [Auto] [GEN 1] [GEN 2] [GEN 4]
M.2_1 Link Mode
This item allows you to set the link speed for M.2_1 Device.
Conguration options: [Auto] [GEN 1] [GEN 2] [GEN 3] [GEN 4]
M.2_2 Link Mode
This item allows you to set the link speed for M.2_2 Device.
Conguration options: [Auto] [GEN 1] [GEN 2] [GEN 3] [GEN 4]
SB Link Mode
This item allows you to set the link speed for Southbridge.
Conguration options: [Auto] [GEN 1] [GEN 2] [GEN 3] [GEN 4]
3-18 Chapter 3: BIOS Setup
Chapter 3
3.6.5 APM Configuration
The items in this menu allow you to set system wake and sleep settings.
ErP Ready
This item allows you to switch off some power at S4+S5 or S5 to get the system ready for
ErP requirement. When set to [Enabled], all other PME options are switched off.
Conguration options: [Disabled] [Enable(S4+S5)] [Enable(S5)]
Restore On AC Power Loss
This item allows your system to go to ON state, OFF state, or both states after an AC power
loss. When setting your system to [Last State], it goes to the previous state before the AC
power loss.
Conguration options: [Power Off] [Power On] [Last State]
Power On By PCI-E/PCI
This item allows you to enable or disable the Wake-on-LAN function of the onboard LAN
controller or other installed PCI-E LAN cards.
Conguration options: [Disabled] [Enabled]
Power On By RTC
This item allows you to enable or disable the RTC (Real-Time Clock) to generate a wake
event and congure the RTC alarm date. When enabled, you can set the days, hours,
minutes, or seconds to schedule an RTC alarm date.
Conguration options: [Disabled] [Enabled]
3.6.6 PCI Subsystem Settings
Allows you to congure PCI, PCI-X, and PCI Express Settings.
SR-IOV Support
This option enables or disables SIngle Root IO Virtualization Support if the system has SR-
IOV capable PCIe devices.
Conguration options: [Disabled] [Enabled]
ROG CROSSHAIR VIII HERO (WI-FI) 3-19
Chapter 3
3.6.7 USB Configuration
The items in this menu allow you to change the USB-related features.
The Mass Storage Devices item shows the auto-detected values. If no USB device is
detected, the item shows None.
Legacy USB Support
[Enabled] Your system supports the USB devices in legacy operating systems.
[Disabled] Your USB devices can be used for BIOS setup only and cannot be
recognized in the boot devices list.
[Auto] Your system automatically detects the presence of USB devices at startup.
If any USB devices are detected, the legacy USB support is enabled.
XHCI Hand-off
[Enabled] Enables the support for operating systems without an XHCI hand-off
feature.
[Disabled] Disables the XHCI Hand-off support.
USB Device Enable
This item allows you to enable or disable USB device support.
Conguration options: [Disabled] [Enabled]
USB Single Port Control
This item allows you to enable or disable the individual USB ports.
Refer to section 1.1.2 Motherboard layout for the location of the USB ports.
3.6.9 Network Stack Configuration
The items in this menu allow you to enable or disable the UEFI network stack
3.6.8 HDD/SSD SMART Information
This menu displays the SMART information of the connected devices.
3-20 Chapter 3: BIOS Setup
Chapter 3
3.7 Monitor menu
The Monitor menu displays the system temperature/power status, and allows you to change
the fan settings.
Scroll down to display the other BIOS items.
Q-fan Configuration
Qfan Tuning
Click this item to automatically detect the lowest speed and congure the minimum
duty cycle for each fan.
W_PUMP+/AIO PUMP Control
[Disabled] Disable the Water Pump control feature.
[Auto] Detects the type of water pump installed and automatically switches
the control modes.
[DC mode] Enable the Water Pump control in DC mode for 3-pin chassis fan.
[PWM mode] Enable the Water Pump control in PWM mode for 4-pin chassis fan.
3.6.10 AMD CBS
The items in this menu display the CPU-related information that the BIOS automatically
detects.
3.6.11 AMD PBS
The items in this menu display the CPU-related information that the BIOS automatically
detects.
ROG CROSSHAIR VIII HERO (WI-FI) 3-21
Chapter 3
3.8 Boot menu
The Boot menu items allow you to change the system boot options.
Boot Configuration
Fast Boot
[Disabled] Allows your system to go back to its normal boot speed.
[Enabled] Allows your system to accelerate the boot speed.
The following item appears only when you set the Fast Boot to [Enabled].
Next Boot after AC Power Loss
[Normal Boot] Returns to normal boot on the next boot after an AC power loss.
[Fast Boot] Accelerates the boot speed on the next boot after an AC power loss.
Setup Mode
[Advanced Mode] This item allows you to go to Advanced Mode of the BIOS after
POST.
[EZ Mode] This item allows you to go to EZ Mode of the BIOS after POST.
CSM (Compatibility Support Module)
This item allows you to congure the CSM (Compatibility Support Module) items to fully
support the various VGA, bootable devices and add-on devices for better compatibility.
Launch CSM
[Auto] The system automatically detects the bootable devices and the add-
on devices.
[Enabled] For better compatibility, enable the CSM to fully support the non-
UEFI driver add-on devices or the Windows® UEFI mode.
[Disabled] Disable the CSM to fully support the non-UEFI driver add-on devices
or the Windows® UEFI mode.
The following items appear only when you set the Launch CSM to [Enabled].
Boot Devices Control
This item allows you to select the type of devices that you want to boot.
Conguration options: [UEFI and Legacy OPROM] [Legacy OPROM only]
[UEFI only]
Boot from Network Devices
This item allows you to select the type of network devices that you want to
launch.
Conguration options: [Ignore] [Legacy only] [UEFI driver rst]
Boot from Storage Devices
This item allows you to select the type of storage devices that you want to
launch.
Conguration options: [Ignore] [Legacy only] [UEFI driver rst]
3-22 Chapter 3: BIOS Setup
Chapter 3
Boot from PCI-E/PCI Expansion Devices
This item allows you to select the type of PCI-E/PCI expansion devices
that you want to launch.
Conguration options: [Legacy only] [UEFI driver rst]
Secure Boot
This item allows you to congure the Windows® Secure Boot settings and manage its keys to
protect the system from unauthorized access and malwares during POST.
Boot Option Priorities
These items specify the boot device priority sequence from the available devices. The
number of device items that appears on the screen depends on the number of devices
installed in the system.
• To access Windows® OS in Safe Mode, press <F8> after POST (Windows® 8 not
supported).
• To select the boot device during system startup, press <F8> when the ASUS Logo
appears.
Boot Override
These items displays the available devices. The number of device items that appears on
the screen depends on the number of devices installed in the system. Click an item to start
booting from the selected device.
3.9 Tool menu
The Tool menu items allow you to congure options for special functions. Select an item
then press <Enter> to display the submenu.
Setup Animator
This item allows you to enable or disable the Setup animator.
Conguration options: [Enabled] [Disabled]
3.9.1 ASUS EZ Flash 3 Utility
This item allows you to run ASUS EZ Flash 3. When you press <Enter>, a conrmation
message appears. Use the left/right arrow key to select between [Yes] or [No], then press
<Enter> to conrm your choice.
For more details, refer to section 3.11.2 ASUS EZ Flash 3.
ROG CROSSHAIR VIII HERO (WI-FI) 3-23
Chapter 3
3.9.2 ASUS Secure Erase
SSD speeds may lower over time as with any storage medium due to data processing.
ASUS Secure Erase completely and safely cleans your SSD, restoring it to factory
performance levels.
To launch ASUS Secure Erase, click Tool > ASUS Secure Erase on the Advanced mode
menu.
Check the ASUS support site for a full list of SSDs tested with ASUS Secure Erase. The
drive may become unstable if you run ASUS Secure Erase on an incompatible SSD.
The time to erase the contents of your SSD may take a while depending on its size. Do
not turn off the system during the process.
Status definition:
• Frozen. The frozen state is the result of a BIOS protective measure. The BIOS
guards drives that do not have password protection by freezing them prior to booting.
If the drive is frozen, a power off or hard reset of your PC must be performed to
proceed with the ASUS Secure Erase.
• Locked. SSDs might be locked if the ASUS Secure Erase process is either
incomplete or was stopped. This may be due to a third party software that uses a
different password dened by ASUS. You have to unlock the SSD in the software
before proceeding with ASUS Secure Erase.
Displays the
available SSDs
3-24 Chapter 3: BIOS Setup
Chapter 3
3.9.4 ASUS SPD Information
This item allows you to view the DRAM SPD information.
Load Profile
This item allows you to load the previous BIOS settings saved in the BIOS Flash. Key in the
prole number that saved your BIOS settings, press <Enter>, and then select Yes.
• DO NOT shut down or reset the system while updating the BIOS to prevent the
system boot failure!
• We recommend that you update the BIOS le only coming from the same memory/
CPU conguration and BIOS version.
Profile Name
This item allows you to key in a prole name.
Save to Profile
This item allows you to save the current BIOS settings to the BIOS Flash, and create a
prole. Key in a prole number from one to eight, press <Enter>, and then select Yes.
Load/Save Profile from/to USB Drive
This item allows you to load or save prole from your USB drive, load and save prole to
your USB drive.
3.9.3 ASUS User Profile
This item allows you to store or load multiple BIOS setting proles.
3.9.5 Graphics Card Information
This item displays the information about the graphics card installed in your system.
GPU Post
This item displays the information and recommended conguration for the PCIE slots that
the graphics card is installed in your system.
This feature is only supported on selected ASUS graphics cards.
Bus Interface
This item allows you to select the bus interface.
Conguration options: [PCIEX16/X8_1]
ROG CROSSHAIR VIII HERO (WI-FI) 3-25
Chapter 3
3.9.6 ASUS Armoury Crate
This item allows you to enable or disable the system to download ASUS Armoury Crate.
Download & Install ARMOURY CRATE app
This item allows you to enable Armoury Crate download Process.
Conguration options: [Disabled] [Enabled]
3.10 Exit menu
The Exit menu items allow you to load the optimal default values for the BIOS items, and
save or discard your changes to the BIOS items. You can access the EZ Mode from the Exit
menu.
Load Optimized Defaults
This option allows you to load the default values for each of the parameters on the Setup
menus. When you select this option or if you press <F5>, a conrmation window appears.
Select OK to load the default values.
Save Changes & Reset
Once you are nished making your selections, choose this option from the Exit menu to
ensure the values you selected are saved. When you select this option or if you press
<F10>, a conrmation window appears. Select OK to save changes and exit.
Discard Changes & Exit
This option allows you to exit the Setup program without saving your changes. When you
select this option or if you press <Esc>, a conrmation window appears. Select Yes to
discard changes and exit.
Launch EFI Shell from USB drives
This item allows you to attempt to launch the EFI Shell application (shellx64.e) from one of
the available lesystem devices.
3-26 Chapter 3: BIOS Setup
Chapter 3
3.11 Updating BIOS
The ASUS website publishes the latest BIOS versions to provide enhancements on system
stability, compatibility,and performance. However, BIOS updating is potentially risky. If
there is no problem using the current version of BIOS, DO NOT manually update the BIOS.
Inappropriate BIOS updating may result to system’s failure to boot. Carefully follow the
instructions in this chapter to update your BIOS when necessary.
Visit http://www.asus.com to download the latest BIOS le for this motherboard.
The following utilities allow you to manage and update the motherboard BIOS setup
program.
1. EZ Update: Updates the BIOS in Windows® environment.
2. ASUS EZ Flash 3: Updates the BIOS using a USB ash drive.
3. ASUS CrashFree BIOS 3: Restores the BIOS using the motherboard support DVD or
a USB ash drive when the BIOS le fails or gets corrupted.
3.11.1 EZ Update
The EZ Update is a utility that allows you to update the motherboard BIOS in Windows®
environment.
• EZ Update requires an Internet connection either through a network or an ISP
(Internet Service Provider).
• This utility is available in the support DVD that comes with the motherboard package.
ROG CROSSHAIR VIII HERO (WI-FI) 3-27
Chapter 3
3.11.2 ASUS EZ Flash 3
ASUS EZ Flash 3 allows you to download and update to the latest BIOS through the Internet
without having to use a bootable oppy disk or an OS-based utility.
Updating through the Internet varies per region and Internet conditions. Check your local
Internet connection before updating through the Internet.
To update the BIOS by USB:
1. Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select
ASUS EZ Flash Utility and press <Enter>.
2. Insert the USB ash disk that contains the latest BIOS le to the USB port.
3. Select via Storage Device(s).
4. Press <Tab> to switch to the Drive eld.
5. Press the Up/Down arrow keys to nd the USB ash disk that contains the latest
BIOS, and then press <Enter>.
6. Press <Tab> to switch to the Folder Info eld.
7. Press the Up/Down arrow keys to nd the BIOS le, and then press <Enter> to
perform the BIOS update process. Reboot the system when the update process is
done.
3-28 Chapter 3: BIOS Setup
Chapter 3
• This function can support devices such as a USB ash disk with FAT 32/16 format
and single partition only.
• DO NOT shut down or reset the system while updating the BIOS to prevent system
boot failure!
Ensure to load the BIOS default settings to ensure system compatibility and stability.
Select the Load Optimized Defaults item under the Exit menu. See section 3.10 Exit
Menu for details.
To update the BIOS by Internet:
1. Enter the Advanced Mode of the BIOS setup program. Go to the Tool menu to select
ASUS EZ Flash Utility and press <Enter>.
2. Select via Internet.
3. Press the Left/Right arrow keys to select an Internet connection method, and then
press <Enter>.
Ensure to load the BIOS default settings to ensure system compatibility and stability.
Select the Load Optimized Defaults item under the Exit menu. See section 3.10 Exit
Menu for details.
4. Follow the onscreen instructions to complete the update.
5. Reboot the system when the update process is done.
ROG CROSSHAIR VIII HERO (WI-FI) 3-29
Chapter 3
3.11.3 ASUS CrashFree BIOS 3
The ASUS CrashFree BIOS 3 utility is an auto recovery tool that allows you to restore the
BIOS le when it fails or gets corrupted during the updating process. You can restore a
corrupted BIOS le using the motherboard support DVD or a USB ash drive that contains
the BIOS le.
The BIOS le in the motherboard support DVD may be older than the BIOS le published
on the ASUS ofcial website. If you want to use the newer BIOS le, download the le at
https://www.asus.com/support/ and save it to a USB ash drive.
Recovering the BIOS
To recover the BIOS:
1. Turn on the system.
2. Insert the motherboard support DVD to the optical drive, or the USB ash drive
containing the BIOS le to the USB port.
3. The utility automatically checks the devices for the BIOS le. When found, the utility
reads the BIOS le and enters ASUS EZ Flash 3 automatically.
4. The system requires you to enter BIOS Setup to recover the BIOS setting. To ensure
system compatibility and stability, we recommend that you press <F5> to load default
BIOS values.
DO NOT shut down or reset the system while updating the BIOS! Doing so can cause
system boot failure!
3-30 Chapter 3: BIOS Setup
Chapter 3
ROG CROSSHAIR VIII HERO (WI-FI) 4-1
Chapter 4
RAID Support
4
Chapter 4: RAID Support
4.1 AMD RAID Array configurations
The motherboard comes with the RaidXpert2 Conguration Utility that supports Volume,
RAIDABLE, RAID 0, RAID 1, and RAID 10 (depends on system licensing) congurations.
For more information on conguring your RAID sets, please refer to the RAID
Configuration Guide which you can nd at https://www.asus.com/support.
4.1.1 RAID definitions
Volume provides the ability to link-together storage from one or several disks, regardless
of the size of the space on those disks. This conguration is useful in scavenging space on
disks unused by other disks in the array. This conguration does not provide performance
benets or data redundancy, disk failure will result in data loss.
RAIDABLE arrays (also known as RAID Ready) are a special type of Volume (JBOD) that
allows the user to add more storage space or create a redundant array after a system is
installed. RAIDABLE arrays are created using Option ROM, UEFI, or rcadm.
The ability to create RAIDABLE arrays may vary per system.
RAID 0 (Data striping) optimizes two identical hard disk drives to read and write data in
parallel, interleaved stacks. Two hard disks perform the same work as a single drive but at a
sustained data transfer rate, double that of a single disk alone, thus improving data access
and storage. Use of two new identical hard disk drives is required for this setup.
RAID 1 (Data mirroring) copies and maintains an identical image of data from one drive to
a second drive. If one drive fails, the disk array management software directs all applications
to the surviving drive as it contains a complete copy of the data in the other drive. This RAID
conguration provides data protection and increases fault tolerance to the entire system.
Use two new drives or use an existing drive and a new drive for this setup. The new drive
must be of the same size or larger than the existing drive.
RAID 10 is data striping and data mirroring combined without parity (redundancy data)
having to be calculated and written. With the RAID 10 conguration you get all the benets
of both RAID 0 and RAID 1 congurations. Use four new hard disk drives or use an existing
drive and three new drives for this setup.
4-2 Chapter 4: RAID Support
Chapter 4
ROG CROSSHAIR VIII HERO (WI-FI) A-1
Appendix
Appendix
Appendix
Q-Code table
Code Description
00 Not used
01 Power on. Reset type detection (soft/hard).
02 AP initialization before microcode loading
03 System Agent initialization before microcode loading
04 PCH initialization before microcode loading
06 Microcode loading
07 AP initialization after microcode loading
08 System Agent initialization after microcode loading
09 PCH initialization after microcode loading
0B Cache initialization
0C – 0D Reserved for future AMI SEC error codes
0E Microcode not found
0F Microcode not loaded
10 PEI Core is started
11 – 14 Pre-memory CPU initialization is started
15 – 18 Pre-memory System Agent initialization is started
19 – 1C Pre-memory PCH initialization is started
2B – 2F Memory initialization
30 Reserved for ASL (see ASL Status Codes section below)
31 Memory Installed
32 – 36 CPU post-memory initialization
37 – 3A Post-Memory System Agent initialization is started
3B – 3E Post-Memory PCH initialization is started
4F DXE IPL is started
50 – 53 Memory initialization error. Invalid memory type or incompatible memory
speed
54 Unspecied memory initialization error
55 Memory not installed
56 Invalid CPU type or Speed
57 CPU mismatch
58 CPU self test failed or possible CPU cache error
59 CPU micro-code is not found or micro-code update is failed
5A Internal CPU error
5B Reset PPI is not available
5C – 5F Reserved for future AMI error codes
(continued on the next page)
A-2 Appendix
Appendix
Q-Code table
Code Description
E0 S3 Resume is stared (S3 Resume PPI is called by the DXE IPL)
E1 S3 Boot Script execution
E2 Video repost
E3 OS S3 wake vector call
E4 – E7 Reserved for future AMI progress codes
E8 S3 Resume Failed
E9 S3 Resume PPI not Found
EA S3 Resume Boot Script Error
EB S3 OS Wake Error
EC – EF Reserved for future AMI error codes
F0 Recovery condition triggered by rmware (Auto recovery)
F1 Recovery condition triggered by user (Forced recovery)
F2 Recovery process started
F3 Recovery rmware image is found
F4 Recovery rmware image is loaded
F5 – F7 Reserved for future AMI progress codes
F8 Recovery PPI is not available
F9 Recovery capsule is not found
FA Invalid recovery capsule
FB – FF Reserved for future AMI error codes
60 DXE Core is started
61 NVRAM initialization
62 Installation of the PCH Runtime Services
63 – 67 CPU DXE initialization is started
68 PCI host bridge initialization
69 System Agent DXE initialization is started
6A System Agent DXE SMM initialization is started
6B – 6F System Agent DXE initialization (System Agent module specic)
70 PCH DXE initialization is started
71 PCH DXE SMM initialization is started
72 PCH devices initialization
73 – 77 PCH DXE Initialization (PCH module specic)
78 ACPI module initialization
79 CSM initialization
7A – 7F Reserved for future AMI DXE codes
(continued on the next page)
ROG CROSSHAIR VIII HERO (WI-FI) A-3
Appendix
Q-Code table
Code Description
90 Boot Device Selection (BDS) phase is started
91 Driver connecting is started
92 PCI Bus initialization is started
93 PCI Bus Hot Plug Controller Initialization
94 PCI Bus Enumeration
95 PCI Bus Request Resources
96 PCI Bus Assign Resources
97 Console Output devices connect
98 Console input devices connect
99 Super IO Initialization
9A USB initialization is started
9B USB Reset
9C USB Detect
9D USB Enable
9E – 9F Reserved for future AMI codes
A0 IDE initialization is started
A1 IDE Reset
A2 IDE Detect
A3 IDE Enable
A4 SCSI initialization is started
A5 SCSI Reset
A6 SCSI Detect
A7 SCSI Enable
A8 Setup Verifying Password
A9 Start of Setup
AA Reserved for ASL (see ASL Status Codes section below)
AB Setup Input Wait
AC Reserved for ASL (see ASL Status Codes section below)
AD Ready To Boot event
AE Legacy Boot event
AF Exit Boot Services event
B0 Runtime Set Virtual Address MAP Begin
B1 Runtime Set Virtual Address MAP End
B2 Legacy Option ROM Initialization
B3 System Reset
(continued on the next page)
A-4 Appendix
Appendix
Code Description
B4 USB hot plug
B5 PCI bus hot plug
B6 Clean-up of NVRAM
B7 Conguration Reset (reset of NVRAM settings)
B8– BF Reserved for future AMI codes
D0 CPU initialization error
D1 System Agent initialization error
D2 PCH initialization error
D3 Some of the Architectural Protocols are not available
D4 PCI resource allocation error. Out of Resources
D5 No Space for Legacy Option ROM
D6 No Console Output Devices are found
D7 No Console Input Devices are found
D8 Invalid password
D9 Error loading Boot Option (LoadImage returned error)
DA Boot Option is failed (StartImage returned error)
DB Flash update is failed
DC Reset protocol is not available
Q-Code table
ACPI/ASL Checkpoints
Code Description
0x01 System is entering S1 sleep state
0x02 System is entering S2 sleep state
0x03 System is entering S3 sleep state
0x04 System is entering S4 sleep state
0x05 System is entering S5 sleep state
0x10 System is waking up from the S1 sleep state
0x20 System is waking up from the S2 sleep state
0x30 System is waking up from the S3 sleep state
0x40 System is waking up from the S4 sleep state
0xAC System has transitioned into ACPI mode. Interrupt controller is in PIC mode.
0xAA System has transitioned into ACPI mode. Interrupt controller is in APIC mode.
ROG CROSSHAIR VIII HERO (WI-FI) A-5
Appendix
Notices
FCC Compliance Information
Responsible Party: Asus Computer International
Address: 48720 Kato Rd., Fremont, CA 94538, USA
Phone / Fax No: (510)739-3777 / (510)608-4555
Identification of the assembled product: INTEL® WI-FI 6 AX200
Identication of the modular components used in the assembly:
Model Name: INTEL® WI-FI 6 AX200 FCC ID: PD9AX200NG
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF exposure warning
This equipment must be installed and operated in accordance with provided instructions and
the antenna(s) used for this transmitter must be installed to provide a separation distance of
at least 20 cm from all persons and must not be co-located or operating in conjunction with
any other antenna or transmitter. End-users and installers must be provide with antenna
installation instructions and transmitter operating conditions for satisfying RF exposure
compliance.
A-6 Appendix
Appendix
Compliance Statement of Innovation, Science and Economic
Development Canada (ISED)
This device complies with Innovation, Science and Economic Development Canada licence
exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for
harmful interference to co-channel mobile satellite systems.
CAN ICES-3(B)/NMB-3(B)
Déclaration de conformité de Innovation, Sciences et
Développement économique Canada (ISED)
Le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement
économique Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
La bande 5150–5250 MHz est réservée uniquement pour une utilisation à l’intérieur an de
réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant
les mêmes canaux.
CAN ICES-3(B)/NMB-3(B)
VCCI: Japan Compliance Statement
Class B ITE
KC: Korea Warning Statement
ROG CROSSHAIR VIII HERO (WI-FI) A-7
Appendix
REACH
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of
Chemicals) regulatory framework, we published the chemical substances in our products at
ASUS REACH website at http://csr.asus.com/english/REACH.htm.
DO NOT throw the motherboard in municipal waste. This product has been designed to
enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin
indicates that the product (electrical and electronic equipment) should not be placed in
municipal waste. Check local regulations for disposal of electronic products.
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol
of the crossed out wheeled bin indicates that the battery should not be placed in municipal
waste.
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest
standards for protecting our environment. We believe in providing solutions for you to
be able to responsibly recycle our products, batteries, other components as well as the
packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for detailed
recycling information in different regions.
Regional notice for California
WARNING
Cancer and Reproductive Harm -
www.P65Warnings.ca.gov
Google™ License Terms
Copyright© 2018 Google Inc. All Rights Reserved.
Licensed under the Apache License, Version 2.0 (the “License”); you may not use this le
except in compliance with the License. You may obtain a copy of the License at:
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software distributed under the
License is distributed on an “AS IS” BASIS, WITHOUT WARRANTIES OR CONDITIONS
OF ANY KIND, either express or implied.
See the License for the specic language governing permissions and limitations under the
License.
A-8 Appendix
Appendix
NCC: Taiwan Wireless Statement
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛航安全及
干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或
工業、科學及醫療用電波輻射性電機設備之干擾。
應避免影響附近雷達系統之操作。
Japan RF Equipment Statement
屋外での使用について
本製品は、5GHz帯域での通信に対応しています。電波法の定めにより5.2GHz、5.3GHz帯域の電
波は屋外で使用が禁じられています。
法律および規制遵守
本製品は電波法及びこれに基づく命令の定めるところに従い使用してください。日本国外では、
その国の法律または規制により、本製品の使用ができないことがあります。このような国では、本
製品を運用した結果、罰せられることがありますが、当社は一切責任を負いかねますのでご了承
ください。
Précautions d’emploi de l’appareil :
a. Soyez particulièrement vigilant quant à votre sécurité lors de l’utilisation de cet
appareil dans certains lieux (les avions, les aéroports, les hôpitaux, les stations-
service et les garages professionnels).
b. Évitez d’utiliser cet appareil à proximité de dispositifs médicaux implantés. Si
vous portez un implant électronique (stimulateurs cardiaques, pompes à insuline,
neurostimulateurs…), veuillez impérativement respecter une distance minimale de 15
centimètres entre cet appareil et l’implant pour réduire les risques d’interférence.
c. Utilisez cet appareil dans de bonnes conditions de réception pour minimiser le niveau
de rayonnement. Ce n’est pas toujours le cas dans certaines zones ou situations,
notamment dans les parkings souterrains, dans les ascenseurs, en train ou en voiture
ou tout simplement dans un secteur mal couvert par le réseau.
d. Tenez cet appareil à distance du ventre des femmes enceintes et du bas-ventre des
adolescents.
ROG CROSSHAIR VIII HERO (WI-FI) A-9
Appendix
Forenklet EU-overensstemmelseserklæring
ASUSTeK Computer Inc. erklærer hermed at denne enhed er i
overensstemmelse med hovedkravene og øvrige relevante bestemmelser i
direktivet 2014/53/EU. Hele EU-overensstemmelseserklæringen kan ndes på
https://www.asus.com/support/
Wi-Fi, der bruger 5150-5350 MHz skal begrænses til indendørs brug i lande,
der er anført i tabellen:
Vereenvoudigd EU-conformiteitsverklaring
ASUSTeK Computer Inc. verklaart hierbij dat dit apparaat voldoet aan de
essentiële vereisten en andere relevante bepalingen van Richtlijn 2014/53/
EU. De volledige tekst van de EU-conformiteitsverklaring is beschikbaar op
https://www.asus.com/support/
De WiFi op 5150-5350MHz zal beperkt zijn tot binnengebruik voor in de tabel
vermelde landen:
Lihtsustatud EÜ vastavusdeklaratsioon
Käesolevaga kinnitab ASUSTek Computer Inc, et seade vastab direktiivi
2014/53/EÜ olulistele nõuetele ja teistele asjakohastele sätetele. EL
vastavusdeklaratsiooni täistekst on saadaval veebisaidil
https://www.asus.com/support/
Sagedusvahemikus 5150-5350 MHz töötava WiFi kasutamine on järgmistes
riikides lubatud ainult siseruumides:
Eurooppa - EY:n vaatimustenmukaisuusvakuutus
ASUSTek Computer Inc. ilmoittaa täten, että tämä laite on direktiivin 2014/53/
EU olennaisten vaatimusten ja muiden asiaankuuluvien lisäysten mukainen.
Koko EY:n vaatimustenmukaisuusvakuutuksen teksti on luettavissa
osoitteessa https://www.asus.com/support/
5 150 - 5 350 MHz:in taajuudella toimiva WiFi on rajoitettu sisäkäyttöön
taulukossa luetelluissa maissa:
ASUSTek Computer Inc
2014/53/EU
.https://www.asus.com/support/
WiFi 5150-5350
Απλοποιημένη Δήλωση Συμμόρφωσης ΕΕ
Διά του παρόντος η ASUSTek Computer Inc. δηλώνει ότι αυτή η συσκευή
είναι σύμμορφη με τις βασικές προϋποθέσεις και άλλες σχετικές διατάξεις της
Οδηγίας 2014/53/ΕE. Το πλήρες κείμενο της δήλωσης συμμόρφωσης της ΕΕ
είναι διαθέσιμο στη διεύθυνση https://www.asus.com/support/
Το WiFi που λειτουργεί στη ζώνη 5150-5350MHz περιορίζεται για χρήση σε
εσωτερικούς χώρους για τις χώρες που αναφέρονται στον παρακάτω πίνακα:
2014/53/EU
5150-5350MHzWi-Fi
Egyszerűsített EU megfelelőségi nyilatkozat
Az ASUSTek Computer Inc. ezennel kijelenti, hogy ez az eszköz megfelel az
2014/53/EU sz. irányelv alapvető követelményeinek és egyéb vonatkozó
rendelkezéseinek. Az EU megfelelőségi nyilatkozat teljes szövegét a
következő weboldalon tekintheti meg: https://www.asus.com/support/
Az 5150-5350 MHz-es sávban működő Wi-Fi-t beltéri használatra kell
korlátozni az alábbi táblázatban felsorolt országokban:
Pernyataan Kesesuaian UE yang Disederhanakan
ASUSTeK Computer Inc. dengan ini menyatakan bahwa perangkat ini
memenuhi persyaratan utama dan ketentuan relevan lainnya yang terdapat
pada Petunjuk 2014/53/EU. Teks lengkap pernyataan kesesuaian EU tersedia
di: https://www.asus.com/support/
WiFi yang Beroperasi pada 5150-5350 MHz akan terbatas untuk penggunaan
dalam ruangan di negara yang tercantum dalam tabel
Vienkāršota ES atbilstības paziņojums
ASUSTeK Computer Inc. ar šo paziņo, ka šī ierīce atbilst Direktīvas
2014/53/ES būtiskajām prasībām un citiem citiem saistošajiem nosacījumiem.
Pilns ES atbilstības paziņojuma teksts pieejams šeit:
https://www.asus.com/support/
Wi-Fi darbība 5150–5350MHz ir jāierobežo lietošanai telpās valstīs, kuras
norādītas tālāk.
Simplied EU Declaration of Conformity
ASUSTek Computer Inc. hereby declares that this device is in compliance
with the essential requirements and other relevant provisions of Directive
2014/53/EU. Full text of EU declaration of conformity is available at
https://www.asus.com/support/
The WiFi operating in the band 5150-5350MHz shall be restricted to indoor
use for countries listed in the table below:
Déclaration simpliée de conformité de l’UE
ASUSTek Computer Inc. déclare par la présente que cet appareil est conforme
aux critères essentiels et autres clauses pertinentes de la directive 2014/53/
EU. La déclaration de conformité de l’UE peut être téléchargée à partir du site
internet suivant : https://www.asus.com/support/
Dans la plage de fréquence 5150-5350 MHz, le Wi-Fi est restreint à une
utilisation en intérieur dans les pays listés dans le tableau ci-dessous:
Vereinfachte EU-Konformitätserklärung
ASUSTek COMPUTER INC erklärt hiermit, dass dieses Gerät mit den
grundlegenden Anforderungen und anderen relevanten Bestimmungen
der Richtlinie 2014/53/EU übereinstimmt. Der gesamte Text der EU-
Konformitätserklärung ist verfügbar unter: https://www.asus.com/support/
Der WLAN-Betrieb im Band von 5150-5350 MHz ist für die in der unteren
Tabelle aufgeführten Länder auf den Innenbereich beschränkt:
Dichiarazione di conformità UE semplicata
ASUSTek Computer Inc. con la presente dichiara che questo dispositivo è
conforme ai requisiti essenziali e alle altre disposizioni pertinenti con la
direttiva 2014/53/EU. Il testo completo della dichiarazione di conformità UE è
disponibile all’indirizzo: https://www.asus.com/support/
L’utilizzo della rete Wi-Fi con frequenza compresa nell’intervallo 5150-
5350MHz deve essere limitato all’interno degli edici per i paesi presenti
nella seguente tabella:
Упрощенное заявление о соответствии европейской директиве
ASUSTek Computer Inc. заявляет, что устройство соответствует основным
требованиям и другим соответствующим условиям директивы 2014/53/EU.
Полный текст декларации соответствия ЕС доступен на
https://www.asus.com/support/
Работа WiFi в диапазоне частот 5150-5350 должна быть ограничена
использованием в помещениях для стран, перечисленных в таблице ниже:
ASUSTek Computer
2014/53/EU
https://www.asus.com/support/
5150-5350 WiFi
Опростена декларация за съответствие на ЕС
С настоящото ASUSTek Computer Inc. декларира, че това устройство е
в съответствие със съществените изисквания и другите приложими
постановления на свързаната Директива 2014/53/EC. Пълният текст на ЕС
декларация за съвместимост е достъпен на адрес
https://www.asus.com/support/
WiFi, работеща в диапазон 5150-5350MHz, трябва да се ограничи до
употреба на закрито за страните, посочени в таблицата по-долу:
Declaração de Conformidade UE Simplicada
ASUSTek Computer Inc. declara que este dispositivo está em conformidade
com os requisitos essenciais e outras disposições relevantes relacionadas às
diretivas 2014/53/UE. O texto completo da declaração de conformidade CE
está disponível em https://www.asus.com/support/
O WiFi operando na banda 5150-5350MHz deve ser restrito para uso interno
para os países listados na tabela abaixo:
Pojednostavljena EU Izjava o sukladnosti
ASUSTeK Computer Inc. ovim izjavljuje da je ovaj uređaj sukladan s bitnim
zahtjevima i ostalim odgovarajućim odredbama direktive 2014/53/EU. Cijeli
tekst EU izjave o sukladnosti dostupan je na https://www.asus.com/support/
WiFi koji radi na opsegu frekvencija 5150-5350 MHz bit će ograničen na
upotrebu u zatvorenom prostoru u zemljama na donjem popisu:
Zjednodušené prohlášení o shodě EU
Společnost ASUSTek Computer Inc. tímto prohlašuje, že toto zařízení splňuje
základní požadavky a další příslušná ustanovení směrnice 2014/53/ EU. Plné
znění prohlášení o shodě EU je k dispozici na adrese
https://www.asus.com/support/
V zemích uvedených v tabulce je provoz sítě Wi-Fi ve frekvenčním rozsahu 5
150 - 5 350 MHz povolen pouze ve vnitřních prostorech:
A-10 Appendix
Appendix
Supaprastinta ES atitikties deklaracija
Šiame dokumente bendrovė „ASUSTek Computer Inc.“ pareiškia, kad šis
prietaisas atitinka pagrindinius reikalavimus ir kitas susijusias Direktyvos
2014/53/ES nuostatas. Visas ES atitikties deklaracijos tekstas pateikiamas čia:
https://www.asus.com/support/
Toliau nurodytose šalyse „WiFi“ ryšiu, veikiančiu 5 150–5 350 MHz dažnio
juostoje, galima naudotis tik patalpose:
Ovaj uređaj može da se koristi u državama navedenim ispod:
Forenklet EU-samsvarserklæring
ASUSTek Computer Inc. erklærer herved at denne enheten er i samsvar med
hovedsaklige krav og andre relevante forskrifter i direktivet 2014/53/EU.
Fullstendig tekst for EU-samsvarserklæringen nnes på:
https://www.asus.com/support/
Wi-Fi-området 5150–5350 MHz skal begrenses til innendørs bruk for landene
som er oppført i tabellen:
Uproszczona deklaracja zgodności UE
Firma ASUSTek Computer Inc. niniejszym oświadcza, że urządzenie to jest
zgodne z zasadniczymi wymogami i innymi właściwymi postanowieniami
dyrektywy 2014/53/EU. Pełny tekst deklaracji zgodności UE jest dostępny pod
adresem https://www.asus.com/support/
W krajach wymienionych w tabeli działanie sieci Wi-Fi w paśmie 5150–
5350MHz powinno być ograniczone wyłącznie do pomieszczeń:
Declaração de Conformidade Simplicada da UE
A ASUSTek Computer Inc. declara que este dispositivo está em conformidade
com os requisitos essenciais e outras disposições relevantes da Diretiva
2014/53/UE. O texto integral da declaração de conformidade da UE está
disponível em https://www.asus.com/support/
A utilização das frequências WiFi de 5150 a 5350MHz está restrita a
ambientes interiores nos países apresentados na tabela:
Declarație de conformitate UE, versiune simplicată
Prin prezenta, ASUSTek Computer Inc. declară că acest dispozitiv este în
conformitate cu reglementările esențiale și cu celelalte prevederi relevante
ale Directivei 2014/53/UE. Textul complet al declarației de conformitate UE
este disponibil la adresa https://www.asus.com/support/
Pentru ţările listate în tabelul de mai jos, reţelele WiFi care funcţionează în
banda de frecvenţă de 5.150-5.350 MHz trebuie utilizate doar în interior:
Pojednostavljena Deklaracija o usaglašenosti EU
ASUSTek Computer Inc. ovim izjavljuje da je ovaj uređaj usaglašen sa
osnovnim zahtevima i drugim relevantnim odredbama Direktive 2014/53/EU.
Ceo tekst Deklaracije o usaglašenosti EU dostupan je na lokaciji
https://www.asus.com/support/
WiFi koji radi u frekventnom opsegu od 5150 MHz do 5350 MHz ograničen
je isključivo na upotrebu u zatvorenom prostoru za zemlje navedene u
tabeli ispod:
Zjednodušené vyhlásenie o zhode platné pre EÚ
Spoločnosť ASUSTek Computer Inc. týmto vyhlasuje, že toto zariadenie je
v súlade so základnými požiadavkami a ďalšími príslušnými ustanoveniami
smernice č. 2014/53/EÚ. Plné znenie vyhlásenia o zhode pre EÚ je k dispozícii
na lokalite https://www.asus.com/support/
Činnosť WiFi v pásme 5150 - 5350 MHz bude obmedzená na použitie vo
vnútornom prostredí pre krajiny uvedené v tabuľke nižšie:
Poenostavljena izjava EU o skladnosti
ASUSTek Computer Inc. tukaj izjavlja, da je ta naprava skladna s temeljnimi
zahtevami in drugimi relevantnimii določili Direktive 2014/53/EU. Polno
besedilo izjave EU o skladnosti je na voljo na https://www.asus.com/support/
WiFi, ki deluje v pasovnem območju 5150–5350MHz, mora biti v državah,
navedenih v spodnjem seznamu, omejen na notranjo uporabo:
Declaración de conformidad simplicada para la UE
Por la presente, ASUSTek Computer Inc. declara que este dispositivo cumple
los requisitos básicos y otras disposiciones pertinentes de la directiva
2014/53/EU. En https://www.asus.com/support/ está disponible el texto
completo de la declaración de conformidad para la UE.
La conexión WiFi con una frecuencia de funcionamiento de 5150-5350 MHz
se restringirá al uso en interiores para los países enumerados en la tabla:
Förenklad EU-försäkran om överensstämmelse
ASUSTek Computer Inc. deklarerar härmed att denna enhet överensstämmer
med de grundläggande kraven och andra relevanta bestämmelser i direktiv
2014/53/EU. Fullständig text av EU-försäkran om överensstämmelse nns på
https://www.asus.com/support/
WiFi som använder 5150-5350 MHz kommer att begränsas för användning
inomhus i de länder som anges i tabellen:
ประกาศเกี่ยวกับความสอดคล้องของสหภาพยุโรปแบบย่อ
ASUSTek Computer Inc.
ขอประกาศในที่นี้ว่าอุปกรณ์นี้มีความสอดคล้องกับความ
ต้องการที่จำาเป็นและเงื่อนไขที่เกี่ยวข้องอื่น ๆ ของบทบัญญัติข้อกำาหนด
2014/53/EU เนื้อหาที่สมบูรณ์ของประกาศความสอดคล้องกับ EU มีอยู่ที่
https://www.asus.com/support/
การทำางานของ WiFi ที่ 5150-5350MHz
ถูกจำากัดให้ใช้ในอาคารสำาหรับประเทศที่แสดงในตาราง
Basitleştirilmiş AB Uyumluluk Bildirimi
ASUSTek Computer Inc., bu aygıtın 2014/53/EU Yönergesinin temel
gereksinimlerine ve diğer ilgili hükümlerine uygun olduğunu bildirir. AB
uygunluk bildiriminin tam metni şu adreste bulunabilir:
https://www.asus.com/support/
5150-5350 MHz arasındaki WiFi çalışması, tabloda listelenen ülkeler için iç
mekân kullanımıyla kısıtlanacaktır.
Спрощена декларація про відповідність нормам ЄС
ASUSTek Computer Inc. заявляє, що цей пристрій відповідає основним
вимогам та іншим відповідним вимогам Директиви 2014 / 53 / EU.
Повний текст декларації відповідності нормам ЄС доступний на
https://www.asus.com/support/
Робота Wi-Fi на частоті 5150-5350 МГц обмежується використанням у
приміщенні для країн, поданих у таблиці нижче:
AT BE BG CZ DK EE FR
DE IS IE IT EL ES CY
LV LI LT LU HU MT NL
NO PL PT RO SI SK TR
FI SE CH UK HR
INTEL® WI-FI 6 AX200 output power table:
Function Frequency Maximum Output Power
(EIRP)
WiFi
2400 - 2483.5 MHz 18.57 dBm
5150 - 5350 MHz 19.13 dBm
5470 - 5725 MHz 18.41 dBm
5725 - 5850 MHz 9.11 dBm
Bluetooth 2402 - 2483.5 MHz 11.68 dBm
For the standard EN 300 440 V2.1.1, if this device operates in
5725-5875 MHz, it will be considered as a receiver category 2.
ROG CROSSHAIR VIII HERO (WI-FI) A-11
Appendix
ASUS contact information
ASUSTeK COMPUTER INC.
Address 4F, No. 150, Li-Te Road, Peitou, Taipei 112, Taiwan
Telephone +886-2-2894-3447
Fax +886-2-2890-7798
Web site www.asus.com
Technical Support
Telephone +86-21-38429911
Fax +86-21-5866-8722, ext. 9101#
Online support http://qr.asus.com/techserv
ASUS COMPUTER INTERNATIONAL (America)
Address 48720 Kato Rd., Fremont, CA 94538, USA
Telephone +1-510-739-3777
Fax +1-510-608-4555
Web site http://www.asus.com/us/
Technical Support
Support fax +1-812-284-0883
Telephone +1-812-282-2787
Online support http://qr.asus.com/techserv
ASUS COMPUTER GmbH (Germany and Austria)
Address Harkort Str. 21-23, 40880 Ratingen, Germany
Fax +49-2102-959931
Web site http://www.asus.com/de
Online contact http://eu-rma.asus.com/sales
Technical Support
Telephone +49-2102-5789555
Support Fax +49-2102-959911
Online support http://qr.asus.com/techserv
A-12 Appendix
Appendix