Table of Contents
-
KL1508A / KL1516A User Manual
- Introduction
- Hardware Setup
- Basic Operation
- OSD Operation
- Hotkey Operation
- Hotkey Port Control
- Invoking Hotkey Mode
- Selecting the Active Port
- Auto Scan Mode Switching
- Skip Mode Switching
- Computer Keyboard / Mouse Reset
- Setting the Hotkey Beeper ON/OFF
- Setting the Hotkey key combination
- Setting the OSD Hotkey combination
- Setting the Port Operating System
- Restore the Default Values
- Hotkey Summary Table
- Keyboard Emulation
- The Firmware Upgrade Utility
- Appendix
ATEN KL1508AM User Manual
Displayed below is the user manual for KL1508AM by ATEN which is a product in the KVM Switches category. This manual has pages.
Related Manuals
Cat 5 High-Density Dual Rail LCD KVM Switch
KL1508A / KL1516A
User Manual
www.aten.com
KL1508A / KL1516A User Manual
ii
EMC Information
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installe d and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
The device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
CE Warning: This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be required to
take adequate measures.
Suggestion: Shielded twist ed pair (STP) cables must be used with the unit to
ensure compliance with FCC & CE standards.
KCC Statement
유선 제품용 /A급 기기 (업무용 방송 통신 기기 )
이 기기는 업무용 (A 급)전자파적합기기로서 판매자 또는 사용자는 이
점을 주의하시기 바라며 ,가정 외의 지역에서 사용하는 것을 목적으로
합니다 .
KL1508A / KL1516A User Manual
iii
RoHS
This product is RoHS complian t.
SJ/T 11364-2006
The following contains information that relates to China.
KL1508A / KL1516A User Manual
iv
User Information
Online Registration
Be sure to register your product at our on line support center:
Telephone Support
For telephone support, call this num ber:
User Notice
All information, docu men tation, and specifications containe d in thi s m anual
are subject to change without prior notificatio n by the m a nufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particu lar purpose. Any of
the manufacturer's software described in this manual is sold or licensed as is.
Should the progr ams pro ve defectiv e following their purchase, the buyer (and
not the manufacturer, its distributor, or its dealer), assumes the entire cost of all
necessary servicing, repair and any incidental or consequential damages
resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV
interference caused by unauthorized modifications to this device. It is the
responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation
of this system if the correct operational voltage setting was not selected prior
to operation. PL EASE VERIFY THAT THE VOLTAGE S E TTING IS
CORRECT BEFORE USE.
International http://eservice.aten.com
International 886-2-8692-6959
China 86-400-810-0-810
Japan 81-3-5615-5811
Korea 82-2-467-6789
North America 1-888-999-ATEN ext 4988
United Kingdom 44-8-4481-58923
KL1508A / KL1516A User Manual
v
Package Contents
The KL1508A / KL1516A package consists of:
1KL1508
A or KL1516A Cat 5 High-Density Dual Rail LCD KVM Switch
with Standard Rack Mount Kit
1 Firmware Upgrade Cable
1Power Cord
1 User Instructions*
Check to make sure that all of the components are present and in good order.
If anything is missing, or was damaged in shipping , contact your dealer.
Read this manual thorough ly and follow the installation and op erati on
procedures carefully to prevent any damage to the switch or to any other
devices on the KL1508A / KL1516A installation.
*Features may have been added to the KL1508A / KL1516A since this manual
was published. Please visit our web site to downl oad the most up-to-date
version of the manual.
Copyright © 2010-2017 ATEN® International Co., Ltd.
Manual Date: 2017-03-10
Altusen and the Altusen logo are registered trademarks of ATEN International Co., Ltd. All rights reserved.
All other brand names and trademarks are the registered property of their respective owners.
KL1508A / KL1516A User Manual
vi
Contents
EMC Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
SJ/T 11364-2006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xi
Chapter 1.
Introduction
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
External Console. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Computers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
KVM Adapter Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Front View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Keyboard Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
KL1508A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
KL1516A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Chapter 2.
Hardware Setup
Before you Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Standard Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Single Station Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Daisy Chaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Chapter 3.
Basic Operation
Opening the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Opening Separately . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Opening Together . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
KL1508A / KL1516A User Manual
vii
Operating Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Closing the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
LCD OSD Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
The LCD Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
The Adjustment Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
OSD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Hotkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Hot Plugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Hot Plugging Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Hot Plugging KVM Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Hot Plugging Console Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Powering Off and Restarting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Port ID Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Chapter 4.
OSD Operation
OSD Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
OSD Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
OSD Main Screen Headings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
OSD Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
F1: GOTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
F2: LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
F3: SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
F4: ADM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
F5: SKP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
F6: BRC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
F7: SCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
F8: LOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Chapter 5.
Hotkey Operation
Hotkey Port Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Invoking Hotkey Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Number Lock and Minus Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Control and F12 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Hotkey Mode Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Exiting Hotkey Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Selecting the Active Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Auto Scan Mode Switching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Setting the Scan Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Entering Auto Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Exiting Auto Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Skip Mode Switching. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
KL1508A / KL1516A User Manual
viii
Entering Skip Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Exiting Skip Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Computer Keyboard / Mouse Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Setting the Hotkey Beeper ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Setting the Hotkey key combination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Setting the OSD Hotkey combination . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Setting the Port Operating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Restore the Default Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Hotkey Summary Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Chapter 6.
Keyboard Emulation
Mac Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Sun Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Chapter 7.
The Firmware Upgrade Utility
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Performing the Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Starting the Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Upgrade Succeeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Main Board Firmware Upgrade Recovery. . . . . . . . . . . . . . . . . . . 63
Adapter Cable Firmware Upgrade Recovery . . . . . . . . . . . . . . . . 64
Appendix
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
North America. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Connection Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
KL1508A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
KL1516A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Compatible Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
OSD Factory Default Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Administrator Login Failure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Optional Rack Mounti ng . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Dedicated Invocation Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
KL1508A / KL1516A User Manual
x
About This Manual
This User Manual is provided to help you get the most from your KL1 508A /
KL1516A system. It covers all aspects of installation, configuration and
operation. An overview of th e information found in the manual is provided
below.
Overview
Chapter 1, Introduction, introduces you to the KL1508A / KL1516A
system. Its purpose, features and benefits are presented, and its front and back
panel components are described.
Chapter 2, Hardware Setup, describes how to set up your installation. The
necessary steps – from a basic s ingle stage hookup to a complete daisy chained
operation are provided.
Chapter 3, Basic Operation, explains the fundamental concepts involved
in operating the KL1508A / KL1516A.
Chapter 4, OSD Operation, provides a complete description of the
KL1508A / KL1516A's OSD (On Screen Display), and how to work with it.
Chapter 5, Hotkey Operation, details all of the concepts and procedures
involved in the keyboard ho tkey operation of your KL1508A / KL1516A
installation.
Chapter 6, Keyboard Emulation, provides tables that list the PC to Mac
and PC to Sun keyboard emulation mapp ings.
Chapter 7, The Firmware Upgrade Utility, explains how to upgrade the
KL1508A / KL1516A's firmware with the latest available versions.
An Appendix, provides specifications and other technical information
regarding the KL1508A / KL1516A.
KL1508A / KL1516A User Manual
xi
Conventions
This manual uses the following conv entions:
Product Information
For information about all ALTUSEN products and how they can help you
connect without limits, visit ALTUSEN on the Web or contact an ALTUSEN
Authorized Reseller. Visit ALTUSEN on the Web for a list of locations and
telephone numbers
International – http://www.aten.com
Monospaced Indicates text that you should key in.
[ ] Indicates keys you should press. For example, [Enter]
means to press the Enter key. If keys need to be chorded,
they appear together in the same bracket with a plus sign
between them: [Ctrl+Alt].
1. Numbered lists represent procedures with sequential steps.
♦Bullet lists provide information, but do not involve sequential
steps.
→Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, S tart → Run means
to open the Start menu, and then select Run.
Indicates critical information.
1
Chapter 1
Introduction
Overview
A KL1508A or KL1516A KVM switch is a control unit that allows IT
administrators to access and control multiple computers from a single PS/2 or
USB KVM (keyboard, monitor, and mouse) console. A single KL1508A /
KL1516A can control up to 8 / 16 computers. They consist of an integrated
LED-backlit LCD monitor, keyboard, and touchpad in a 1U rack-mountable
retractable sliding housing.
The similarities and differences among the models in the KL1508A / KL1516A
series are shown in the following table:
The LCD and keyboard/touchpad modules slide independently of each other.
To maximize space in your data center, the keyboard/touchpad module slides
back to "hide away" when not in use, while the thin profile LCD monitor
rotates back – flush against the rack – allowing administrators to monitor
computer activity on the installation.
By daisy chaining up to 31 additional switches, as many as 512 computers can
be controlled from the original KVM console. An aut o-sensin g function
recognizes the position of each station on the chain, eliminating the need to
manually set the position, and a seven-segment front panel LED displays each
Station's position for easy identi fication.
Compact, high-density, RJ-45 connectors and CAT 5e/6 cable make for a
compact, efficient, wiring configuration, while the use of PS/2 and USB KVM
Adapter Cables to link to the computers, permits any combination of PCs,
Macs, Sun computers, and serial devices to coexist on the installation.
Setting up the KL1508A / KL1516A is fast and easy – plugging cables into their
appropriate ports is all that is entailed. Because the KL1508A / KL1516A
intercepts keyboard and mouse input directly, there is no software to configure
and no complex installation routines.
Model LCD Panel Ports
KL1508AM 17" 8
KL1508AN 19" 8
KL1516AM 17" 16
KL1516AN 19" 16
2
Access to any computer on the installation is easily accomplished – either by
pressing front panel port selection pushbuttons; entering hotkey combinations
from the keyboard; or by means of a powerful OSD (On Screen Display) menu
system. A convenient Auto Scan function also permits automatic scanning and
one-by-one monitoring of the activities of selected computers.
Your KL1508A / KL1516A investmen t is protected through firmware
upgrades. You can download firmware update files from our website, and use
the Firmware Upgrade function to quickly and conveni ently install them.
There is no better way to save time and money than with a KL1508A /
KL1516A installation. By using the KL1508A / KL1516A with its sliding LCD
console to manage your installation, you: (1) eliminate the expense of
purchasing separate keyboards, monitors, and mice; (2) save all the space those
extra components would take up; (3) save space that a keyboard, monitor, and
mouse would take with a standard KVM switch; (4) save on energy costs; and
(5) eliminate the inconvenience and wasted effort involved in constantly
having to move from one computer to an oth e r.
KL1508A / KL1516A User Manual
3
Features and Benefits
The features and benefits provided by a KL1508A / KL1516A deployment are
described in the following table:
Features Benefits
Simple Installation and
Operation Plug-and-play installation – no software required – connecting
cables is all it takes. Station positions are automatically
recognized. Computer selection via front panel switches;
hotkeys; or multi-language OSD (On Screen Display) menus.
Keyboard/Touchpad
module KVM console with 17"or 19" LED-backlit LCD monitor in a
sliding housing with top and bottom clearance for smooth
operation in a 1U high rack.
Dual Rail operation – LCD monitor slides independently of the
keyboard/touchpad.
Console lock enables the sliding console to remain securely
locked away when not in use.
LED Light Exclusive LED illumination light – designed by ATEN to
illuminate the keyboard and touchpad to allow visibility in low-
light conditions.
Single Console Control Access and control up to 8 (KL1508A) or 16 (KL1516A)
computers from a single PS/2 or USB KVM (keyboard, video,
and mouse) console.
Scalability By daisy chaining up to 31 additional KL1508A / KL1516A
switches, as many as 512 computers can be controlled from
the original KVM console – eliminating the expense of
purchasing separate peripherals for each server.
Easy Installation Setting up the KL1508A / KL1516A is fast and easy – plugging
cables into their appropriate ports is all that is entailed.
Because there is no software to configure, incompatibility and
configuration issues are non-existent.
Easy Operation Three port selection methods: Manual (via front panel
pushbuttons), Hotkey, and multi-language OSD (On Screen
Display).
Keyboard Language support: English (US); English (UK);
German; German (Swiss); French; Spanish; Traditional
Chinese; Japanese; Korean; Swedish; Italian; Russian;
Hungarian and Greek
Hardware Independent
Cross-Platform
Support
The KL1508A / KL1516A supports Windows 2000/XP/Vist a/7,
Linux, Unix, Novell, FreeBSD, Sun, and Mac.
Space-Saving RJ-45
Connectors and Cat
5e/6 Cabling
This space-saving innovation means that the KL1508A /
KL1516A can be conveniently installed in a 1U system rack,
and the installation can take advantage of the internal
network wiring built into most modern commercial buildings.
Reduces cable clutter for a neat and tidy data center
environment
Chapter 1. Introduction
4
Features Benefits
KVM Adapter Cables
to Connect to Servers
and Devices
For convenience and flexibility that allows mixing the PS/2,
USB and serial interfaces, the KL1508A / KL1516A's design
utilizes KVM adapter cables that serve as intermediaries
between the KVM switch and the connected devices.
KVM adapter cables are available in PS/2, USB, and Serial
interfaces to support a wide variety of data center servers
and devices.
Two-Level Password
Security Supports one administrator and ten user profiles. Strong
password protection prevents unauthorized accessing to the
installation – keeping your valuable data secure.
Upgradeable Firmware Stay current with the latest functionality improvements and
updates by downloading firmware upgrade files from our
website and installing them with the built-in firmware upgrade
utility.
Effortless Upgrades Simultaneous firmware upgrades to all daisy-chained KVM
switches and dongles through the daisy-chain cable.
Auto Scanning and
Broadcast Mode Auto scanning provides hands-free monitoring of selected
devices at variable rates. Broadcast Mode sends commands
from the console to all computers – allowing you to perform
operations (such as software installation, upgrades,
shutdowns, etc.), on them simultaneously
Superior Video Quality Supports the video resolutions up to 1280x1024@75hz for up
to 50 meters with the new ATEN KVM Cable Adapter KA7000
series.
Multiple User Accounts Supports up to 10 user and 1 administrator accounts
Hot Pluggable Ability to add or remove components without having to power
off the KVM switch.
Adapter Cables with ID The KL1508A / KL1516A KVM series supports automatic ID
recognition of the new ATEN KVM Cable Adapter KA7000
series (KVM Adapter Cables). Using the new adapter cables
with ID means it is not required to change cable configuration
settings when moving cables from port to port.
Device ID and attributes are stored in the adapter cables
allowing you to hot-swap port connections without having to
reconfigure attributes.
KL1508A / KL1516A User Manual
5
Requirements
External Console
A VGA, SVGA, or multisync monitor capable of the hig hest resolution
that you will be using on any computer in the installation
A PS/2 or USB mouse
A PS/2 or USB keyboard
Computers
The following equipment must be installed on the computers that connect to the
KL1508A or KL1516A KVM ports:
A VGA, SVGA or multisync port
Note: The integrated LCD monitor's maximum resolution is
1280 x 1024 @ 75Hz. If you want to use a higher setting for the
screen resolutions of the attached computers, see Troubleshooting,
page 79.
A Type A USB port and US B host controller (for USB KVM adapter cable
connection, see following section)
- or -
6-pin Mini-DIN keyboard and mouse ports (for PS/2 KVM adapter cable
connection, see following section)
KVM Adapter Cables
Cat 5e/6 cable is required to connect the KL1508A / KL1516A to one of
the KVM adapter cables.
The following KVM adapter cables are required for use with the KL1508A
/ KL1516A:
Function Module
Connect to devices with PS/2 ports KA7920 / KA7520 / KA7120
KA9520 / KA9120
Connect to devices with USB ports KA7166, KA7168, KA7169,
KA7970 / KA7570 / KA7170
KA9570 / KA9170
Connect to Sun Legacy systems (with 13W3 port) KA9130 / KA7130
Connect to Sun USB systems KA9170 / KA7170
Chapter 1. Introduction
6
Note: 1. KVM adapter cables are referred to as I/O Modules in some dialog
boxes.
2. The following cable models support the Adapter Cabl e ID func tion :
KA7920 / KA7970 / KA7520 / KA7570 / KA7120 / KA7130 /
KA7166 / KA7168 / KA7169 / KA7170.
Operating Systems
Supported operating systems are shown in the table, below:
1 Does not support USB.
2 Kernels below 2.6 do not support USB 2.0
Connect to serial based devices KA9140
OS Version
Windows NT1, Server 2003, Server 2008, and higher
Linux2RedHat 9.0, Fedora and higher, RHEL AS 4, RHEL 5
SuSE 10 and higher, OpenSUSE 10.2; SLES 10 SP1
Debian 3.1, 4.0
Ubuntu 7.04, 7.10
UNIX IBM AIX4.3, 5L (V5.2,V5.3), V6 (V6.1)
FreeBSD 5.5, 6.1, 6.2
Novell Netware 5.0 and higher
Sun Solaris 8, 9, 10
Mac 9.0, 9.1, 10.1, 10.2, 10.3, 10.4 , 10.5
DOS 6.2 and higher1
Function Module
KL1508A / KL1516A User Manual
7
Components
Front View
No. Component Description
1 Upper Handle Pull to slide the LCD module out; push to slide the module in.
See Opening the Console, page 20, for details on sliding the
console in and out.
2 LCD Module See LCD Module , page 9.
3 Keyboard Module See Keyboard Module, page 8.
4 Lower Handle Pull to slide the keyboard module out. See Opening the
Console, page 20, for more details on sliding the console in
and out.
5 Power LED Lights (blue) to indicate that the unit is receiving power.
6 Keyboard
Release Catch These catches (one on each side) release the keyboard
module so you can slide it away.
7 LCD Release
Catch These catches (one on each side) release the LCD module
so you can slide it away.
8 Rack Mounting
Tabs The rack mounting tabs located at each corner of the unit
secure the chassis to a system rack. See Standard Rack
Mounting, page 12, for details.
9 LED Light Exclusive LED illumination light – designed by ATEN to
illuminate the keyboard and touch pad to allow visibility in
low-light conditions
Chapter 1. Introduction
8
Keyboard Module
No. Component Description
1 Keyboard Standard 105-key keyboard
2 Touchpad Standard mouse touchpad
3 External Mouse
Port This USB-type mouse port is provided for users who prefer to
use an external mouse.
4 Station ID LED In a daisy chained installation, the Station ID of the currently
selected station displays as a 2-digit figure in this panel.
See Port ID Numbering, page 30 for further details.
5 S tation Selection
Area The LED displays the station number that the port with the
KVM focus is located on.
The left button shifts the KVM focus down the chain
(Station 2 → Station 1, etc.). After Station 1, it cycles back
to the last Station.
The right button shifts the KVM focus up the chain. After
the last Station, it cycles to Station 1.
6 Lock LEDs &
Reset Switch The Num Lock, Caps Lock, Scroll Lock LEDs are located
here.
A Reset Switch is located just to the right of the Lock LEDs.
Press this recessed switch in with a thin object to perform a
system reset.
7 Port Selection
Buttons and
LEDs
To access a Port on the currently selected Station press its
corresponding port selection button. Indicator LEDs are built
into the switches:
An On Line LED lights to indicate that the computer
attached to its corresponding port is up and running.
A Selected LED lights to indicate which port has the KVM
focus.
KL1508A / KL1516A User Manual
9
LCD Module
No. Component Description
1 LCD Display To access the LCD monitor, slide the LCD module out and flip
up the cover. See Opening the Console, page 20, for details
on sliding the LCD module out.
2 LCD Controls These buttons control the position and picture settings of the
LCD display. See LCD OSD Configuration, page 26, for
details.
3 LCD On/Off
Button Push this button to turn the LCD monitor on and off. The
button lights when the LCD monitor is off to indicate that only
the monitor is off – not the KVM switch itself.)
4 Firmware
Upgrade Section Firmware Upgrade Port: The Firmware Upgrade Cable that
transfers the firmware upgrade data from the administrato r's
computer to the KL1508A / KL1516A plugs into this RJ-11
connector.
Firmware Upgrade Switch: During normal operation this
switch should be in the NORMAL position. (See The Firmware
Upgrade Utility, page 57 for firmware upgrading details.)
Chapter 1. Introduction
10
Rear View
KL1508A
KL1516A
No. Component Description
1 Grounding
Terminal The grounding wire used to ground the switch attaches here.
2 Power Socket This is a st andard 3-prong AC power socket. The power cord
from an AC source plugs in here.
3 Power Switch This standard rocker switch powers the unit on and off.
4 Daisy Chain
Port When Daisy Chaining Units (see Daisy Chaining, page 18),
the daisy chain cable plugs in here.
5Console Port
Section If this is a Single Station installation, or if this is the First
Station of a daisy chained installation, the keyboard, monitor,
and mouse that make up the Local Console plug in here.
6 KVM Port
Section The Cat 5/6e cables that link to the KVM Adapter Cables
(which link to the computers) plug in here.
2 3 4
5
6
1
5
6
1
2 3 4
11
Chapter 2
Hardware Setup
Before you Begin
1. Important safety information regarding the placement of this
device is provided on page 65. Please review it before
proceeding.
2. Make sure that power to all the devices you will be connecting
up has been turned off. You must unplug the power cords of any
computers that have the Keyb oard Power On function.
3. Packing material has been inserted to protect the KL1508A /
KL1516A during shipping. Slide the LCD module out (see
Opening the Console, page 20), until the packing material is
visible. Remove the packing material before installing the unit,
as shown in the diagram below.
Chapter 2. Hardware Setup
12
Standard Rack Mounting
A standard rack mounting kit is provided with your KL1508A / KL1516A. The
kit enables the switch to be mounted in rack with a depth of 42–77 cm.
Note: It takes two people to mount the switch: one to hold it in place, the other
to screw it in. Optional kits—including single person Easy Installation
kits—are available with a separate purchase. See Rack Mounting,
page 67, for details.
To rack mount the switch, do the following:
1. While one person positions the switch in the rack and holds it in place, the
second person—using the screws provided with the rack mounting kit—
loosely screws the front brackets to the rack.
L Brackets
Side Mountng
Brackets
KL1508A / KL1516A User Manual
13
2. While the first person still holds the switch in place, the second person
slides the L brackets into the switch's side mounting brackets, from the
rear until the bracket flanges contact the rack, then—using the screws
provided with the rack mount ing kit—screws the L brackets to the rack.
3. After the L brackets have been secured, tighten the front bracket screws.
Note: 1. Cage nuts are provided for racks that are not pre-threaded.
2. Allow at least 5.1 cm on each side for proper ventilation, and at least
12.7 cm at the back for the power cord and cable clearance.
Chapter 2. Hardware Setup
14
Single Station Installation
In a single stage installation, there are no additional KVM switches daisy
chained down from the KL1508A / KL1516A. To set up a single stage
installation, refer to the installation diagrams starting on page 15 (the numbers
in the diagram correspond with the num bers of the instructio n steps), and do
the following:
1. Ground the KL1508A / KL1516A by connecting one end of the grounding
wire provided with your switch to the grounding terminal, and the other
end of the wire to a suitable grounded object.
Note: Do not omit this step. Proper grounding helps to prevent damage to
the unit from surges or static electricity.
2. Plug the console keyboard, monitor, and mouse into the unit’s console
ports. The ports are color coded and marked with icons for easy
identification.
Note: You can use any combination of keyboard and mouse connections.
For example, you can use a PS/2 keyboard with a USB mouse.
3. Use Cat 5e/6 cable to connect any available KVM port to a KVM adapter
cable that is appropriate for the computer you are installing (see KVM
Adapter Cables, page 5 for details).
Note: To support a resolution of 1280x1024, the recommended maximum
distance between the unit and the KVM adapter cable is 50 meters.
4. Connect the KVM adapter cable to the computer.
Plug the connectors on the KVM adapter cable into the appropriate ports
of the computer you are installing. (See KVM Adapter Cable Installation
Diagrams, page 16 for connection examples.)
5. Plug the female end of the power cord into the KL1508A / KL1516A's
power socket; plug the male end into an AC power source.
After the KL1508A / KL1516A is cabled up, you can turn on the power. After
it is powered up, you can turn on the servers.
KL1508A / KL1516A User Manual
15
Single Stage Installation Diagram
5
4
3
1
2
3
by ATEN
PS/2 CPU MODULE
MODEL NO. KA9120
PS/2 CPU MODULE
MODEL NO. KA9120
LINK
2
Chapter 2. Hardware Setup
16
KVM Adapter Cable Installation Diagrams
KA7120
KA7520
KA7920
KA9120
KA9520
by ATEN
LINK
KA7170
KA7570
KA7970
KA9170
KA9570
by ATEN
LINK
KA9140
SERIAL TERMINAL
KA7130
KA9130
by ATEN
LINK
KL1508A / KL1516A User Manual
17
KVM Adapter Cable Installation Diagrams cont.
KA7166
KA7168
KA7169
Chapter 2. Hardware Setup
18
Daisy Chaining
To control even more computers, up to 31 additional KL1508A / KL1516A
KVM switches can be daisy chained from the original KL1508A or KL1516A.
As many as 512 computers can be controlled from a single console in a
complete installation.
Note: Since it would be unnecessarily wasteful and expensive to use
KL1508A / KL1516A switches for daisy chaining (there is no point in
having consoles on the chained switches), switches without LCD
consoles are used instead. Please see the table, Compatible Switches,
page 72 for a list of ATEN switches that can be installed on a KL1508A
/ KL1516A daisy chain.
Tables showing the relation between the number of computers and the number
of KL1508A / KL1516A units needed to control them are provided on page 69.
To set up a daisy chained installation, make sure that power to all the devices
you will be connecting up has been turned off, and refer to the Daisy Chaining,
page 18 as you do the following:
1. Use a daisy chain cable set to connect the Chain Out port of the parent
KL1508A / KL1516A unit to the Chain In port of the child KL1508A /
KL1516A unit (first station out to second station in, second station out to
third station in, etc.).
Note: 1. You cannot use the chain in port of the First Station, since it is the
highest level parent.
2. Daisy chain cable sets require a separate purchase. See your
dealer for details.
2. Cable up the computers and the switch according to the information
provided under Single Station Installation, page 14.
3. Repeat the above for any other switches you want to add to the chai n.
4. Power up the installation according to the following procedure:
a) Plug in the power cord for the first station. Wait for the unit to ascertain
its station ID and display it on the Station ID LED. (The station ID for
the first stage unit is 01, the ID for the second stage unit is 02, the ID for
the third stage unit is 03, etc.)
KL1508A / KL1516A User Manual
19
b) Power on each station on the installation in turn (second station, then
third station, etc.). In each case, wait for the station ID to be ascertained
and displayed before powering on the next stati on.
c) After all the stations are up, power on the computers.
Daisy Chain Installation Diagram
20
Chapter 3
Basic Operation
Opening the Console
The KL1508A / KL1516A's console consists of two modules: An LCD display
module located under the top cover; and a keyboard / touchpad module below
the LCD module.
The modules can either slide together, or independently. This allows you to
have the LCD display available for viewing wh ile the keyboard / touchpad
module is conveniently out of th e way when not in use.
Opening Separately
1. Pull the release catch to release the console, and pull the top panel a few
centimeters toward you. Once the console has been released, you can let
go of the catch.
Release Catch
KL1508A / KL1516A User Manual
21
2. Pull the top panel all the way out until it clicks into place.
3. Rotate the top panel all the way back to expose the LCD screen.
Chapter 3. Basic Operation
22
4. Reach underneath and pull the keyboard module all the way out until it
clicks into place.
Opening Together
Refer to the diagrams in the Opening Separately section as you do the
following:
1. Pull the release catch and pull the top and bottom panels out until the
keyboard module clicks into pl ace.
Note: Once the console has been released, you can let go of the catch.
2. Pull the top panel the rest of the way out until it clicks into place.
3. Rotate the top panel all the way back to expose the LCD screen.
Note: Refer to the warning regarding placing excessive weight on the
keyboard module on the following page.
KL1508A / KL1516A User Manual
23
Operating Precautions
RIGHT
Rest your hands and arms lightly on the
keyboard module as you work.
WRONG!
DO NOT lean your body weight on the
keyboard module.
DO NOT place heavy objects on the
keyboard module.
The maximum load bearing capacity of the keyboard module is
30kg. Failure to heed the information below can result in damage
to the keyboard module.
Chapter 3. Basic Operation
24
Closing the Console
1. Pull the release catches located on either side of the keyboard toward you
to release the keyboard module, then slide the module slightly in.
2. Let go of the catches. Using the front handle, push the keyboard module
all the way in.
KL1508A / KL1516A User Manual
25
3. Rotate the LCD module all the way down, then pull the rear catches to
release the LCD module.
4. Using the front han dle, push the mo dul e all the way in.
Chapter 3. Basic Operation
26
LCD OSD Configuration
The LCD Buttons
The LCD OSD allows you to set up and configure the LCD display. Four
buttons (see LCD Controls, page 9) are used to perform the con fig uration, as
described in the table below :
Button Function
MENU When you have not entered the LCD OSD Menu
function, pressing this button invokes the Menu
function and brings up the Main Menu.
When navigating through the menus, this button
moves you right or up. When making an adjustment, it
increases the value.
When navigating through the menus, this button
moves you left or down. When making an adjustment,
it decreases the value.
EXIT When you have not entered the LCD OSD Menu
function, pressing this button performs an auto
adjustment. An auto adjustment automatically
configures all the settings for the LCD panel to what
the OSD considers their optimum values to be.
When you have entered the LCD OSD Menu
function, pressing this button exits the current menu
and returns you to the previous menu. Use it to
leave an adjustment menu when you are satisfied
with the adjustment you have made.
When you are at the Main Menu, pressing this
button exits the LCD OSD.
KL1508A / KL1516A User Manual
27
The Adjustment Settings
An explanation of the LCD OSD adjustment settings is given in the table
below:
Port Selection
KL1508A / KL1516A installations provide three methods to obtain instant
access to any computer on your installation: Manual, OSD (on-screen display),
and Hotkey.
Manual
Manual port selection simply in volves pressing the port selection switch that
corresponds to the device you wish to access.
Setting Explanation
Brightness Adjusts the background black level of the screen image.
Contrast Adjusts the foreground white level of the screen image.
Phase If pixel jitter or horizontal line noise is visible on the display, your
LCD may have the wrong phase setting. Adjust the phase setting
to eliminate these problems.
Clock If vertical banding is visible on the display, your LCD may have
the wrong clock setting. Adjust the clock setting to eliminate
vertical banding.
H-Position Positions the display area on the LCD panel horizont ally (moves
the display area left or right).
V-Position Positions the display area on the LCD panel vertically (moves
the display area up or down).
Color Temperature Adjusts the color quality of the display. You can adjust the
“warmth” value, color balance, etc. The Adjust Color selection
has a further submenu that lets you fine tune the RGB values.
Language Selects the language that the OSD displays its menus in.
OSD Duration Lets you set the amount of time that the OSD displays on the
screen. If there is no input for the amount of time you choose, the
OSD display turns off.
Reset Resets the menu and submenu adjustments (except for
language settings) to the original factory default settings.
Chapter 3. Basic Operation
28
OSD
The OSD provides a menu driven interface to the computer switching
procedure. OSD operation is discussed in the next chapter.
Hotkey
Hotkeys allow you to conveniently provide KVM focus to a particular
computer from the keyboard instead of having to manually select them by
pressing port selection switches, or accessing the OSD. Keyboard operation is
discussed in Chapter 5.
KL1508A / KL1516A User Manual
29
Hot Plugging
The KL1508A / KL1516A supports hot plugging – components can be removed
and added back into the installation by unplugging and replugging their cables
without the need to shut the unit down. In order for ho t plugging to work
properly, however, the procedures describ e d below should be followed.
Hot Plugging Stations
You can switch station positions by simply unplugging from the old parent and
plugging into a new one. After yo u do, in order for the OSD menus to
correspond to the change, you should reset the OSD. See RESET STATION
IDS, page 40, for detai ls.
Hot Plugging KVM Ports
After switching KVM ports, in order for the OSD m enus to correspond to the
change, you may need to reconfigure the OSD info rmation for the new port
information. The settings of the port name, operating system, and keyboard
language will be restored to the KVM switch from any previously used adapter
cables after they are plugged in. See F3: SET, page 36, and the port setting
selections under the F4 ADM function, page 39, for details.
Note: 1. If a computer’s operating system doesn’t support hot plugging, this
function may not work pro perl y.
2. Empty ports that previously were connected to an adapter cable will
retain their prior configuration data.
Hot Plugging Console Ports
The keyboard, monitor, and mouse can be hot plugged. When hot plugging the
mouse, however, be aware of the following:
If you unplug the mouse (to reset the mouse, for example), you must use
the same mouse when you plug back in.
If you plug in a different mouse, all the stations and all the computers on
the installation must be shut down for 10 seconds, then restarted following
the sequence given under Po wering Off and Restarting on page 30.
Some older operating sy stems may not support hot-plugging.
Note: If, after hot plugging (or at any other time), there is no response to
keyboard and/or mouse input, perform a keyboard and mouse reset
by pressing in the Reset switch (see page 8).
Chapter 3. Basic Operation
30
Powering Off and Restarting
If it becomes necessary to po wer off the KL15 08A / KL1516A, or if the switch
loses power and needs to be restarted, before starting it back up you should
follow these procedures to prevent possible equi pm ent issues:
1. Shut down all th e computers that are attached to it.
Note: You must un pl ug the power cord s of any computers that have the
Keyboard Power On function.
2. Wait 10 seconds then power it back on. If you have shut down more than
one station, power up the highest station fi rst and wo rk your way down to
the lowest one. Wait for each stat ion to display its station ID on the front
panel LED before powering on the next one.
3. After the station (s) is (are) up, power the computers back on.
Port ID Numbering
Each computer on the installation is assigned a unique port ID. The port ID is
a one or two segment number that is determined by the stage level and port
number of the switch that the computer is connected to.
The first segment represents the stage level of the switch (04, for example); the
second segment represents the number of the port that the computer is plugged
into.
For example, if a computer is connected to KVM port 3 of a switch that is in
the 12th position of the daisy chain, it would have a port ID of 12-03.
Note: Single digit numbers (1–9) are padded with a preceding zero (0).
31
Chapter 4
OSD Operation
OSD Overview
The On Screen Display (OSD) is a menu driven method to handle computer
control and switching operations. All procedures start from the OSD Main
Screen. To display the Main Screen, tap the OSD hotkey twice.
The default hotkey is [Scroll Lock]. You can change the hotkey to the Ctrl key
or the Alt key if you like (see OSD HOTKEY, page 36).
Note: 1. If you use the Ctrl or Alt key method you must press the same Ctrl or
Alt key both times.
2. Once you start the OSD, the keyboard lock will be control led by th e
device. The number lock and caps lock will always be on when the
OSD is being accessed.
The OSD incorporates a two level (administrator / user) password system.
Before the OSD Main Screen comes up, a login dialog box appears that asks
for a username and password. You must provide a valid usern a me and
password in order to continue.
If this is the first time the OSD is accessed, or if the password function has not
been set, simply press [Enter]. The OSD main screen displays in administrator
mode. In this mode, you have administrator privileges, with access to all
administrator and user functions, and you can set up operations (including
password authorizations) as you like. If the password function has been set, you
must provide an appropriate user/administrator password in order to access the
OSD.
After logging in with the default username and password, the OSD Main
Screen opens in Administrator mode. In this mo de, you have administrator
privileges, with access to all administrator and user functions, and can set up
operations (including password authorization for the future), as you would like.
Chapter 4. OSD Operation
32
When you invoke the OSD, a screen similar to the one below appears:
Note: 1. The diagram depicts the Administrator's Main Screen. The User Main
Screen does not show the F4 and F6 functions, since these are
reserved for the administrator and can't be accessed by ordinary users.
2. Only the ports that have been set accessible by the Administrator for
the currently logged in user are visible (see SET ACCESSIBLE
PORTS, page 39 , for details).
KL1508A / KL1516A User Manual
33
OSD Navigation
To dismiss the menu, and deactivate the OSD, click the X at the upper
right corner of the OSD Window or press Esc.
To Logout click F8 or the ZZZ symbol at the top of the Main Screen, or
press [F8].
The OSD uses a tree view. To see the ports for a particular station, click
the plus sign [ + ] in front of the station number. The port number list
drops down. To dismiss the list, click the circle symbol [ o ] in front of the
station number.
To move up or down through the list one line at a tim e, click the up and
down triangle symbols (ST) or use the up and down arrow keys. If there
are more list entries than there is room for on the Main Screen, the screen
will scroll.
To move up or down through the list one screen at a time, click the up and
down arrow symbols (ÏÐ), or use the [Pg Up] and [Pg Dn] key s. If there
are more list entries than there is room for on the Main Screen, the screen
will scroll.
To bring th e KVM focus to a port, double-click it, or move the highlight
bar to it and then press [Enter].
After executing any action, you automatically go back to the menu one
level above.
OSD Main Screen Headings
Heading Explanation
SN-PN This column lists the port ID numbers (station number-port number) for
all the KVM ports on the installation. The simplest method to access a
particular computer is to click it, or move the highlight bar to it, and then
press [Enter].
QV If a port has been selected for Quick View scanning (see SET QUICK
VIEW PORTS, page 38), an arrowhead displays in this column.
The computers that are powered on and are online have a sun symbol
in this column.
NAME If a port has been given a name (see EDIT PORT NAMES, page 40), its
name appears in this column.
Chapter 4. OSD Operation
34
OSD Functions
OSD functions are used to configure and control the OSD. For example, you
can rapidly switch to any port, scan selected ports only, limit the list you wish
to view, designate a port as a Quick View Port, create or edit a port name, or
make OSD setting adjustments.
To access an OSD function:
1. Either click a function key field at the top of the Main Screen, or press a
function key on the keybo ard.
2. In the submenus that appear make your choice either by double clicking it,
or moving the highlight bar to it, and then pressing [Enter].
3. Press [Esc] to return to the previous menu level.
F1: GOTO
Accessing the GOTO function allows you to switch directly to a port either by
keying in the port's name or its po rt ID.
To use the Name metho d, key in 1, key in the po rt's nam e , and then press
[Enter].
To use the Port ID method, key in 2, key in th e port ID, and then press
[Enter].
Note: You can key in a partial name or port ID. The screen will show all the
computers that the user has View ri ghts to (see SET ACCESSIBLE
PORTS, page 39), that match the name or port ID pattern, regardless of
the current List settings (see F2: LIST, page 35, for details).
To return to the OSD Main Menu without making a choice, press [Esc].
KL1508A / KL1516A User Manual
35
F2: LIST
Many of the switch’s OSD functions only operate on the com puters currently
selected for listing on the Main Screen. Accessing this functio n lets you
broaden or narrow the scope of ports that get listed. The submenu choices and
their meanings are given in the table below:
Move the highlight bar to the cho ice you want, then press [Enter]. An icon
appears before the choice to indicate that it is the currently selected one.
Choice Meaning
ALL Lists all of the ports on the installation.
QUICK VIEW Lists only the ports that have been selected as Quick View Ports
(see SET QUICK VIEW PORTS, page 38).
POWERED ON Lists only the ports that have attached computers Powered On.
QUIC K VIE W +
POWERED ON Lists only the ports that have been selected as Quick View Ports
(see SET QUICK VIEW PORTS, page 38), and that have their
attached computers Powered On.
Chapter 4. OSD Operation
36
F3: SET
Accessing this function allows the administrator and each user to set up an
individual working environment. A separate profile for each operator is stored
by the OSD and is activated according to the username provided during login.
To change a setting:
1. Double-click it; or move the highlight bar to it, then press [Enter].
2. After you select an item, a submenu with further choices appears. To make
a selection, either double click it; or move the highlight bar to it, then press
[Enter]. An icon appears before the selected choice to indicate which one
it is. The settings are explained in the following table:
Setting Function
OSD
HOTKEY Selects which hotkey activates the OSD function:
[Scroll Lock] [Scroll Lock]; [Ctrl] [Ctrl] or [Alt] [Alt].
Since the [Ctrl] or [Alt] key combinations may conflict with programs
running on the computers, the default is the [Scroll Lock] combination.
PORT ID
DISPLAY
POSITION
Allows you to position where the port ID appears on the monitor. The
default is the upper left corner, but you can choose to have it appear
anywhere on the screen.
Use the mouse or the arrow Keys plus Pg Up, Pg Dn, Home, End, and
5 (on the numeric keypad with Num Lock off), to position the port ID
display, then click or press [Enter] to lock the position and return to the
Set submenu.
Note: The setting affects the currently selected port. If you don’t want
to use the default position, you must change the setting for each port
individually.
PORT ID
DISPLAY
DURATION
Determines how long a port ID displays on the monitor after a port
change has taken place. There are two choices: 3 seconds and Off.
PORT ID
DISPLAY
MODE
Selects how the port ID is displayed: the port number alone (PORT
NUMBER); the port name alone (PORT NAME); or the port number
plus the port name (PORT NUMBER + PORT NAME). The default is
PORT NUMBER + PORT NAME).
SCAN
DURATION Determines how long the focus dwells on each port as it cycles through
the selected ports in Auto Scan mode (see F7: SCAN, page 44). Key in
a value from 1–255 seconds, then press [Enter]. Default is 5 seconds;
a setting of 0 disables the Scan function.
KL1508A / KL1516A User Manual
37
Setting Function
SCAN/SKIP
MODE Selects which computers will be accessed under Skip mode (see F5:
SKP, page 42), and Auto Scan mode (see F7: SCAN, page 44).
Choices are:
ALL – All the ports which have been set Accessible (see SET
ACCESSIBLE PORTS, page 39);
QUICK VIEW – Only those ports which have been set Accessible and
have been selected as Quick View Ports (see SET QUICK VIEW
PORTS, page 38);
POWERED ON – Only those ports which have been set Accessible
and are Powered On;
QUICK VIEW + POWERED ON – Only those ports which have been
set Accessible and have been selected as Quick View Ports and are
Powered On. The default is ALL.
SCREEN
BLANKER If there is no input from the console for the amount of time set with this
function, the screen is blanked. Key in a value from 1–30 minutes, then
press [Enter]. A setting of 0 disables this function. The default is Off.
HOTKEY
COMMAND
MODE
Enables / Disables the Hotkey function (see Hotkey Operation,
page 45), in case a conflict with programs running on the computers
occurs. The default is On.
HOTKEY This setting selects the Hotkey invocation keys (see Hotkey Operation,
page 45). Choices are [NUM LOCK] + [-], or [CTRL] + [F12]. The
default is [NUM LOCK] + [-].
OSD
LANGUAGE Sets the language that the OSD displays in. Choices are: English,
German, Japanese, Simplified Chinese and Traditional Chinese.The
default is English.
SET
CONSOLE
KEYBOARD
Sets the keyboard language mapping of the console keyboard. The
default is Auto. If the switch does not automatically receive language
mapping from the keyboard, it will set to English (US).
SET
LOGOUT
TIMEOUT
If there is no input from the console for the amount of time set with this
function, the operator is automatically logged out. A login is necessary
before the console can be used again.
This enables other operators to gain access to the computers when the
original operator is no longer accessing them, but has forgotten to log
out. To set the timeout value, key in a number from 1–180 minutes,
then press [Enter]. If the number is 0 (zero), this function is disabled.
Default is Off.
Note: This feature does not function if Set Login Mode is disabled. See
See SET LOGIN MODE, page 41.
ACTIVATE
BEEPER Choices are Y (for Yes), or N (for No). When activated, the beeper
sounds whenever a port is changed, when activating the Auto Scan
function (see F7: SCAN, page 44), or an invalid entry is made on an
OSD menu. The default is On.
(Continues on next page.)
Chapter 4. OSD Operation
38
(Continued from previous page.)
Setting Function
SET QUICK
VIEW PORTS This function lets the administrator select which ports to include as
Quick View ports.
To select/deselect a port as a Quick View Port, use the navigation
keys to move the highlight bar to it, then press the [Spacebar].
When a port has been selected as a Quick View Port, an arrowhead
displays in the QV column of the LIST on the Main Screen to
indicate so. When a port is deselected, the arrowhead disappears.
If one of the Quick View options is chosen for the LIST view (see
F2: LIST, page 35), only a port that has been selected here will
display on the List.
If one of the Quick View options is chosen for Auto Scanning (see
SCAN/SKIP MODE, page 37), only a port that has been selected
here will be Auto Scanned.
The default is for no ports to be selected.
PREFERRED
RESOLUTION This function allows you to set the preferred resolution for a second
external display* connected to the switches console port, which will be
sent to the KVM adapter cables. The KVM adapter cables provide the
connected computer’s video card with EDID information about the
monitor connected to the switch. This affects the video quality
displaying on the external console monitor. Choices are:
MONITOR DEFAULT SETTING – Sends the EDID information
provided by the switches LCD monitor – to the KVM adapter cable.
Alternative Resolution – Sends the alternative resolution (EDID
information) selected for the external display connected to the
switches console port, to the KVM adapter cables. Select a
resolution that best suits the video display for the monitor connected
to the switches console port.
Note: When using the built in LCD monitor the default resolution must
be set to 1280x1024 60HZ. Only change the preferred resolution
when connecting an external display to the console monitor port.
TOUCHPAD Enables / Disables the touchpad function of the console. Choices are
Y (for Yes), or N (for No). The active status (Touchpad On / Touchpad
Off) is also shown.
KL1508A / KL1516A User Manual
39
F4: ADM
F4 is an administrator only func tion. Accessing this function allows th e
administrator to configure and control the overall operation of the OSD. To
change a setting double click it; or use the up and down arrow keys to move the
highlight bar to it, then press [Enter].
After you select an item, a submenu with further choices appears. Double click
the choice you want, or move the highlight bar to it, then press [Enter]. An icon
appears before the selected choice. The settings are explained in the table on
the next three pages:
Setting Function
SET USER
ACCOUNT This function is used to set usernames and passwords for the
administrator and users:
One Administrator and 10 user passwords can be set.
After you select the administrator field or one of the user fields, a
screen that allows you to key in your username and password
appears. The username and password may be up to 16 characters
long, and can consist of any combination of letters and numbers (A–
Z, 0–9).
For each individual, key in the username and password, then press
[Enter].
To modify or delete a previous username and/or password, use the
backspace key to erase individual letters or numbers.
The icon indicates data is stored in the account.
SET
ACCESSIBLE
PORTS
This function allows the administrator to define user access to the
computers on the installation on a port-by-port basis.
For each user , select the target port, then press the [S p acebar] to cycle
through the choices: F (Full access), V (View Only), or N (No Access).
Repeat until all access rights have been set, then press [Esc]. The
default is F for all users on all ports.
Note: An N setting means that no access rights are granted. The port
will not show up on the user's LIST on the Main Screen.
(Continues on next page.)
Chapter 4. OSD Operation
40
(Continued from previous page.)
Setting Function
EDIT PORT
NAMES To identify which computer is attached to a particular port, every port
can be assigned a name. This function allows the administrator to
create, modify, or delete port names. To assign a port name:
1. Click the port you want, or use the navigation keys to move the
highlight bar to it, then press [Enter].
2. Key in the new port name, or modify/delete the old one. The maxi-
mum number of characters allowed for the port name is 14. Legal
characters include:
All alpha characters: A–Z*
All numeric characters: 0–9
*You can enter the port names in either upper or lower case
however the OSD displays the port name only in UPPERCASE.
3. When you have finished editing, press [Enter] to have the change
take effect. To abort the change, press [Esc].
RESTORE
DEFAULT
VALUES
This function is used to undo all changes and return the setup to the
original factory default settings (see OSD Factory Default Settings,
page 73) – except for the Names settings that were assigned to the
ports, which are saved.
CLEAR THE
NAME LIST This function clears the port name list.
RESET
STATION IDS If you change the position of one of the stations in the daisy chain, the
OSD settings will no longer correspond to the new situation. This
function directs the OSD to rescan the station positions of the entire
installation and updates the OSD so that the OSD station information
corresponds to the new physical layout.
Note: Only the station numbers get updated. Except for the port
names, all administrator settings (such as Set Accessible Ports, Set
Quick View Ports, etc.), for all of the computers affected by the change,
have to be manually redone.
SET
OPERAT ING
SYSTEM
S pecifies the operating platform of the computer attached to each port.
You must configure each port on the installation. For each port, press
the [Spacebar] to cycle through the choices (PC, Mac or Sun). Repeat
until all the ports have been set, then press [Esc]. The default is PC.
Note: If you are installing a Sun or Mac computer it may not boot when
you run it for the first time unless you first set the correct operating
system for the port it is connected to.
KL1508A / KL1516A User Manual
41
Setting Function
SET CAT 5
LENGTH Lets you specify how long the Cat 5/6e cable between the port and the
KVM adapter cable is. Press [Spacebar] to cycle through the cable
length settings:
S: Short – for up to 25 m
M: Medium – for between 20 and 35 m
L: Long – for above 35 m
An S, M, or L appears next to the port to indicate the choice.
SET
KEYBOARD
LANGUAGE
Sets the keyboard language layout for the computers attached to each
port. Press [Spacebar] to cycle through the choices: The default is
English (US).
SET
CONSOLE
MODE
This setting selects which console(s) (internal/external) are enabled:
0 Both consoles enabled
1 LCD Console only
2 External console only
Use the spacebar to cycle through the choices. The default is 0.
Changes will not be saved until you logout.
FIRMWARE
UPGRADE In order to upgrade the KL1508A / KL1516A and adapter cable
firmware (see The Firmware Upgrade Utility, page 57) you must first
enable Firmware Upgrade mode with this setting.
When you bring up this menu, the current firmware version levels
display. Select Y to enable Firmware Upgrade mode, or N to leave this
menu without enabling it.
ADAPTER
UPGRADE This function allows the administrator to check the firmware version of
the KVM adapter cable. When you bring up this menu, the current
firmware version leve ls display. See FIRMWARE UPGRADE, above,
also.
SET LOGIN
MODE This function allows the administrator to request users to login or not.
When the login dialog box is disabled, the system disables the login/
logout function. If the system is re-started, the login/logout function
remains disabled.
Chapter 4. OSD Operation
42
F5: SKP
This function enables you to easily skip backward or forward, switching the
console focus from the currently active KVM Port to the previous or next
available one.
The selection of computers to be available for Skip mode switching is
made with the Scan/Skip mode setti ng under the F3 SET function
(see page 37).
When you are in Skip mode, press:
Note: When you skip, you only skip to the previous or next avail able
computer that is in the Scan/Skip mode selection (see page 37).
If a port has been selected for Scan/Skip mode, when the focus switches to
that port a left/right triangl e symbo l appears before its port ID display.
While Skip mode is in effect, the console will not function normally. You
must exit Skip mode in order to regain control of the console.
To exit Skip mode, press the [Spacebar] or [Esc].
←To skip to the previous port in the List.
→To skip to the next port in the List.
↑To skip to the last port of the previous station in the List.
↓To skip to the first port of the next station in the List.
KL1508A / KL1516A User Manual
43
F6: BRC
F6 is an administrator only function. When this function is in effect, commands
sent from the console are broadcast to all available computers on the
installation.
This function is particularly useful for operations that need to be performed on
multiple computers, such as performing a system wide shutdown, installing or
upgrading software, etc.
While BRC mode is in ef fe ct, a speaker symbol appea rs before the port ID
display of the port that currently has the console focus.
While BRC mode is in effect, the mouse will not function normally. You
must exit BRC mode in order to regain control of the mouse.
To exit BRC mode, invoke the OSD (with the OSD Hotkey), then click the
F6 field, or press [F6], to turn BRC mode off.
Chapter 4. OSD Operation
44
F7: SCAN
This function automatically switches among the available computers at regular
intervals so that you can monitor their activity witho ut having to take the
trouble of switching m a nual ly.
The selection of computers to be included for Auto Scanning is made with
the Scan/Skip mode setting under the F3 SET function (see page 37).
The amount of time that each port displays for is set with the Scan
Duration setting under the F3 SET function (see page 36).
As each computer is accessed, an appears in front of the port ID
display to indicate that it is being accessed under Auto Scan mode.
While you are in Auto Scan mode, you can pause the scanning in order to
keep the focus on a particular computer either by pressing P, or with a left
click of the mouse. To resume scanning, press any key or left click again.
See Auto Scan Mode Switching, page 48, for details.
While Auto Scan mode is in effect, the console will not function normally.
You must exit Auto Scan mode in order to regain control of the console.
To exit Auto Scan mode, press the [Spacebar] or [Esc].
F8: LOUT
Clicking the F8 field, or pressi ng [F8], logs you out of the OSD and blanks the
console screen. This is different from simply deactivating the OSD when you
are at the Main Screen by pressing [Esc].
With this function you must log in all over again to regain access to the OSD,
whereas with [Esc], all you have to do to reenter the OSD is tap the OSD
Hotkey.
Note: 1. When you reenter the OSD aft e r logging out, the screen stays blank
except for the login dialog box. You must input your username and
password before you can continue (see page 31). If login has been
disabled by the administrator (see page 41), the F8 function is also
disabled.
2. If you reenter the OSD after logging out, and immediately use [Esc]
to deactivate the OSD without having selected a port from the OSD
menu, a Null Port message displays on the screen. The OSD hotkey
will bring up the OSD Main Screen.
S
45
Chapter 5
Hotkey Operation
Hotkey Port Control
Hotkey port control allows you to provide KVM focus to a particular computer
directly from the keyboard. The KL1508A / KL1516A provides the following
Hotkey port control features:
Selecting the Active Port
Auto Scan Mode Switchi ng
Skip Mode Switch in g
Computer Keyboard / Mouse Reset
The following settings can also be controlled in Hotkey mode:
Setting the Beeper
Setting the Quick Hotkey
Setting the OSD Hotkey
Setting the Port Operating System
Restoring the OSD Default Values
Chapter 5. Hotkey Operation
46
Invoking Hotkey Mode
All Hotkey operations begin by in voki ng Hotkey mode.1 To invoke Hotkey
mode you may use two possible keystroke sequences shown below. Only one
of the two key-sequences below can be operational (see Setting the Hotkey key
combination on page 52):
Number Lock and Minus Keys
1. Hold dow n the [Num Lock] key;
2. Press and release the [Minus] key;
3. Release the [Num Lock] key:
[Num Lock] + [-]
Control and F12 Keys
1. Hold dow n the [Ctrl] key;
2. Press and release the [F12] key;
3. Release the [Ctrl] key:
[Ctrl] + [F12]
Hotkey Mode Environment
When Hotkey mode is active:
A command line appears on the monitor screen. The command line prompt
is the word Hotkey: in white text on a blue background, and displays the
subsequent Hotkey information that you key in.
Ordinary keyboard and mouse functions are suspended – only Hotkey
compliant keystrokes (described in the sections that follow), can be input.
Exiting Hotkey Mode
Pressing [Esc] exits Hotkey mode.
1. Make sure that the Hotkey Command Mode function is enabled and
that you key in the appropriate Hotkey. See page 37 for details.
KL1508A / KL1516A User Manual
47
Selecting the Active Port
Each computer port is assigned a port ID (see Port ID Numbering, page 30).
You can directly access any computer with a Hotkey combination that specifies
the port ID that the computer is connected to. The steps are:
1. Enter the Hotkey mode with the:
[Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Key in the port ID.
The port ID numbers display on the command li ne as you key them in. If
you make a mistake, use [Backspace] to erase it.
3. Press [Enter].
After you press [Enter], the KVM focus switches to the designated
computer and you automatically exit Hotkey mode.
Note: In Hotkey mode, the KVM focu s wi ll not switch to a port if an
invalid switch or port number is entered. The Hotkey command line
will continue to display on the screen until you enter a valid switch
and port number combination, or exit Hotkey mode.
Chapter 5. Hotkey Operation
48
Auto Scan Mode Switching
Auto Scan automati cally switches among all the active computer ports that are
accessible to the currently logged on user at regular intervals. This allows their
activity to be monitored automatically (See SKAN/SKIP MODE of the OSD F3
SET functio n, page 37).
Setting the Scan Interval
The amount of time Auto Scan keeps the focus on each port is set with the
SCAN DURATION setting of the OSD F3 SET function (see page 36). You can
change the scan interval, before you activate Hotkey Auto Scanning, by
entering the following Hotkey combination:
1. Enter the Hotkey mode:
[Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Key in [A][n]
Where [A] is the letter A, and [n] is a number from 1–255 that
represents the length of the focus time in seconds.
The letter A and the numbers display on the command line as you key
them in. Use [Backspace] to erase any wrong entry.
3. Press [Enter]
After you press [Enter], you exit Hotkey mode, and are ready to start Auto
Scanning.
Entering Auto Scan
To enter the Auto Scanning mode, key in the following Hotkey combination:
1. Enter the Hotkey mode:
[Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Press [A] + [Enter].
While you are in Auto Scan mode, you can pause the scanning to keep
the focus on a particular computer by pressing [P]. When Auto
Scanning is paused, the Command Line displays: Auto Scan: Paused.
When you want to keep the focus on a particular computer, Pausing is
more convenient than exiting Auto Scan mode. When you resume
scanning it starts at the computer where you paused. If you exited and
KL1508A / KL1516A User Manual
49
then restarted Auto Scanning, it starts, at the beginning, from the first
computer on the installation.
To resume Auto Scanning, press any key. Scanning continues from the
computer you paused at.
While the Auto Scan mode is operating, ordinary keyboard and mouse
functions are suspended - only Auto Scan mode compliant keystrokes
can be input. You must exit Auto Scan mode to reg ain normal control
of the console.
Exiting Auto Scan
1. To exit Auto Scan mode press [Esc] or [Spacebar]. Auto Scanning
stops when you exit Auto Scan mode.
Chapter 5. Hotkey Operation
50
Skip Mode Switching
This feature allows you to switch between computers in order to monitor th em
manually. You can focus on a particular port for as long as you like – as
opposed to auto-scanning, which automatically switches the port focus after a
fixed interval.
Entering Skip Mode
To enter Skip mode, key in the following Ho tkey combination:
1. Enter the Hotkey mode by pressin g the:
[Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Press one of the [Arrow] keys.
After you press one of the keyboard arrows, you automatically exit Hotkey
mode and enter Skip mode where you can switch ports as follows:
Once you are in Skip mode, you can continue skipping by pressing the
arrow keys. You do not have to use the [Num Lock] + [-] combinatio n
again.
While Skip mode is in effect, ordinary keyboard and mouse functions are
suspended – only Skip mode compliant keystrokes can be input. You must
exit Skip mode to regain normal control of the console.
Exiting Skip Mode
1. To exit Skip mode, press [Esc] or [Spacebar].
←Skips to the first access i bl e p or t. (See SCAN/SKIP MODE,
page 37, for information regarding accessible ports.)
→Skips to the next accessible port.
↑Skips to the las t acce ssi ble port of th e pre vious st a tion.
↓Skips to the first accessible port of the next station.
KL1508A / KL1516A User Manual
51
Computer Keyboard / Mouse Reset
If either the keyboard or mouse stop functioning on the computer connected to
the currently selected port, you can perform a keyboard / mouse reset on the
computer by executing the follo wing steps:
1. Enter the Hotkey mode with the:
[Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Press [F5].
After you press [F5] you automatically exit Hotkey mode and regain
keyboard and mouse control on the computer connected to the KVM port.
If you fail to regain keyboard / mouse control on the computer after
pressing [F5], perform a system reset. For more information see Lock
LEDs & Reset Switch, page 8.
This function is essentially the same as unplugging and replugging the
keyboard and mouse on the target computer.
Setting the Hotkey Beeper ON/OFF
The beeper (see Activate Beeper, page 37) can be turned on and off with
Hotkeys by the following steps:
1. Enter the Hotkey mode with the:
[Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Press [B].
After you press [B], the beeper turns on or off. The command line displays
Beeper On or Beeper Off for one second; then the message disappears and you
automatically exit Hotk ey mod e .
Chapter 5. Hotkey Operation
52
Setting the Hotkey key combination
The keys used to enter the Hotkey Mode (see HOTKEY COMMAND MODE,
page 37) can be switched between:
[Num Lock] + [-], and [Ctrl] + [F12]
by the following steps:
1. Enter the Hotkey mode with the:
[Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Press [H].
After you press [H], the command line displays HOTKEY HAS BEEN
CHANGED for one second; then the message disappears and you
automatically exit Hotkey mode.
Setting the OSD Hotkey combination
The Hotkeys used to access the OSD (see OSD HOTKEY, page 36) can be
switched between [Scroll Lock], [Scroll Lock], [Ctrl], [Ctrl],
and [Alt], [Alt] by the following steps:
1. Enter the Hotkey mode with the:
[Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Press [T].
After you press [T], the command line displays HOTKEY HAS BEEN
CHANGED for one second; then the message disappears and you
automatically exit Hotkey mode.
KL1508A / KL1516A User Manual
53
Setting the Port Operating System
A port’s operating system configuration can be matched to that of the computer
attached to the port by performing the following steps:
1. Enter the Hotkey mode with the:
[Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Press a [Function] key, where [Function] refers to one of the
function keys in the follo wing table:
After pressing a function key you automatically exit Hotkey mode.
Restore the Default Values
This administrator-only Hotkey restores the KL1508A / KL1516A default
values (see RESTORE DEFAULT VALUES on page 40) by performing the
following steps:
1. Enter the Hotkey mode with the:
[Num Lock] + [-] or [Ctrl] + [F12] combination.
2. Press [R].
3. Press [Enter].
After you press [Enter], the command line displays RESET TO DEFAULT
SETTING for three seconds; then the message disappears and you
automatically exit Hotkey mode.
Key Description
F1 Sets the Port OS to Windows
F2 Sets the Port OS to Mac
F3 Sets the Port OS to Sun
Chapter 5. Hotkey Operation
54
Hotkey Summary Table
[Num Lock] + [-]
or
[Ctrl] + [F12]
[A] [Enter] Invokes Auto Scan mode.
When Auto Scan mode is in effect, [P] or
left-click pauses auto-scanning.
When auto-scanning is paused, pressing
any key or another left-click resumes auto-
scanning.
[B] Toggles the Beeper On or Off.
[Esc] or [Spacebar] Exits hotkey mode.
[F1] Sets Operating System to Windows
[F2] Sets Operating System to Mac
[F3] Sets Operating System to Sun
[H] Toggles the Hotkey invocation keys.
[Port ID] [Enter] Switches access to the computer that
corresponds to that Port ID.
[R] [Enter] Administrator only hotkey. It returns the
switch’s settings to their default values.
[T] Toggles the OSD Hotkey between [Ctrl]
[Ctrl] and [Scroll Lock] [Scroll Lock].
[←]Invokes Skip Mode and skips from the
current port to the first accessible port
previous to it.
[→]Invokes Skip Mode and skips from the
current port to the next accessible port.
[↑]Invokes Skip Mode and skips from the
current port to the last accessible port of the
previous Station.
[↓]Invokes Skip Mode and skips from the
current port to the first accessible port of the
next Station.
55
Chapter 6
Keyboard Emulation
Mac Keyboard
The PC compatible (101/104 key) keyboard can emulate the functions of the
Mac keyboard. The emulation mappings are listed in the table below.
Note: When using key combinations, press and release the first key (Ctrl),
then press and release the activation key.
PC Keyboard Mac Keyboard
[Shift] Shift
[Ctrl] Ctrl
[Ctrl] [1]
[Ctrl] [2]
[Ctrl] [3]
[Ctrl] [4]
[Alt] Alt
[Print Screen] F13
[Scroll Lock] F14
=
[Enter] Return
[Backspace] Delete
[Insert] Help
[Ctrl] F15
Chapter 6. Keyboard Emulation
56
Sun Keyboard
The PC compatible (101/104 key) keyboard can emulate the functions of the
Sun keyboard when the Control ke y [Ctrl] is used in conjunction with other
keys. The corresponding functions are shown in the table below.
Note: When using key combinations, press and release the first key (Ctrl),
then press and release the activation key.
PC Keyboard Sun Keyboard
[Ctrl] [T] Stop
[Ctrl] [F2] Again
[Ctrl] [F3] Props
[Ctrl] [F4] Undo
[Ctrl] [F5] Front
[Ctrl] [F6] Copy
[Ctrl] [F7] Open
[Ctrl] [F8] Paste
[Ctrl] [F9] Find
[Ctrl] [F10] Cut
[Ctrl] [1]
[Ctrl] [2]
[Ctrl] [3]
[Ctrl] [4]
[Ctrl] [H] Help
Compose
-
+
57
Chapter 7
The Firmware Upgrade Utility
Introduction
The purpose of the Windows-based Firmware Upgrade Utility is to provide an
automated process for upgrading the KL1508A / KL1516A and compatible
adapter cable firmware. The program comes as part of a Firmware Upgrade
Package that is specific for each device.
The latest revisions of new firmware for the KL1508A / KL1516A, and
supported KVM Adapter Cables are posted as Firmware Upgrade Packages on
our web site. Check the website regularly to find the latest firmware packages
and information relating to them.
Note: 1. A single upgrade package contains the upgrade files for the Main
Board and all the supported KVM Adapter Cables.
2. KVM Adapter Cables are referred to as I/O Modules in some dialog
boxes.
Before You Begin
To prepare for the firmware upgrade, do the follo wing:
1. From a computer that is not part of your KVM installation go to the ATEN
Internet support site and choose the model name that relates to your device
to get a list of available Firmware Upgrade Packages.
2. Choose the Firmware Upgrade Package you want to install (u sually the
most recent), and download it to your computer.
(Continues on next page.)
Chapter 7. The Firmware Upgrade Utility
58
(Continued from previous page.)
3. Use the firmware upgrade cable (provided with this unit), to con nect a
COM port on your computer to the firmware upgrade port of your device.
Note: On a daisy chained instal lation, connect the cable to the first station
(master) unit. The chained stations (slaves) that are the same model
will receive the upgrade via the daisy chain cables.
4. Shut down all of the computers except those that are attached to cable
adapters that require upgrade. The cable adapters require the computers
power source to be upgraded. Do not shut down the stations on the KVM
installation that you wan t to upgrade.
5. From your KVM switch console, bri ng up the OSD (see page 31) and
select the F4ADM function.
6. Scroll down to FIRMWARE UPGRADE. Press [Enter], then press [Y] to
start the Firmware Upgrade m ode (see page 41).
Note: The upgrade to the KVM Adapter Cables takes place via the Cat 5e/
6 cable that connects the adapter cable to the KVM switch, so there
is no separate firmware upgrade cable to attach.
KL1508A / KL1516A User Manual
59
Performing the Upgrade
Starting the Upgrade
To upgrade your firmware:
1. Run the downloaded Firmware Upgrade Package file, either by double
clicking the file icon, or by opening a command line and keying in the full
path to it.
The Firmware Upgrade Utility Welcome screen appears:
2. Read and Agree to the License Agreement (enable the I Agree radio
button).
(Continues on next page.)
Chapter 7. The Firmware Upgrade Utility
60
(Continued from previous page.)
3. Click Next to continue. The Firmware Upgrade Utility main screen
appears:
The Utility checks to make sure the KL1508A / KL1516A is in the
Firmware Upgrade Mode and then lists all firmware needed preselected in
the Device List panel.
Note: 1. The Device List lists all the models of KVM Adapter Cable that
require upgrading. Selecting the model will upgrade all the
devices of that particular model.
2. If the Utility fails to list any firmware check that the KL150 8 A /
KL1516A is connected and in the Firmware Upgrade Mode.
Alternatively the Firmware Package maybe corrupted or the
wrong version therefore obtain a new copy of the file and retry.
KL1508A / KL1516A User Manual
61
4. Select MAIN to upgrade the firmware for the Main Board. Deselect any
KVM Adapter Cable types that are not required to be upgraded. After you
have made your selection(s), click Next to perform the upgrade.
Check Firmwar e Version - when selected the utility compares the Main
Board firmware level with the upgrade files MAIN. If the device
versions are higher than the upgrade versions a dialog box informs you
and gives you the option to cont inue or cancel.
If you didn't enable Check Firmware Version, the utility installs the
upgrade files without checking wh ether they are a higher level , or not.
As the upgrade proceeds status messages appear in the Status
Messages panel, and the progress toward completion is shown on the
Progress bar.
To abort the upgrade procedure before it completes, click Cancel.
If you cancel before completion, a dialog box warns you that the
upgrade will not finish and shows the options to proceed or abort the
cancel operation. The Mainboard and OSD firmware may be missing or
corrupted upon rebooting the switch .
To recover from missing or corrupt firmware, see Firmware Upgrade Recovery,
page 63.
Chapter 7. The Firmware Upgrade Utility
62
Upgrade Succee d ed
After the upgrade has completed, a screen appears to inform you that the
procedure was successful:
Click Finish to close the Firmware Upgrade Utility.
Note: At the completion of the upgrade, the KL1508A / KL1516A restarts.
KL1508A / KL1516A User Manual
63
Upgrade Failed
If the upgrade failed to complete successfully a dialog box appears asking if
you want to retry. Click Yes to retry. If you click No, the Upgrade Failed
screen appears.
Click Cancel to close the Firmware Upgrade Utility. See the next section,
Firmware Upgrade Recovery, for how to proceed.
Firmware Upgrade Recovery
Should the firmware on the switch be missing or corrupted it may not be
possible to operate or boot the switch . This coul d be due to:
Starting the Firmware Upgrade mode (see FIRMWARE UPGRADE,
page 41), and then canceling the upgrade.
An interruption of the firmware upg rade.
The firmware upgrade procedure failing.
The unit’s firmware becoming corrupted for unknown reasons.
Main Board Firmware Upgrade Recovery
To perform a firmware upgrade recovery, do the following:
1. On the KVM Switch slide the Firmware Upgrade Recovery Switch (see
page 8) to the Recover position.
2. Power off and restart the switch according to the instructions given in the
Powering Off and Restarting section (see page 30).
3. Proceed with the firmware upgrade as described in Performing the
Upgrade, starting on page 59.
4. When the upgrade ends, power off the switch
5. Slide the Firmware Upgrade Recovery Switch back to the Normal
position.
6. Power on the switch.
Note: If one of the child KVM units fai ls to upg rade successful ly, unchain it
from the installation and perform the recovery and upgrade operation on
it independently. After it has been successfully upgraded, plug it back
into the chain
Chapter 7. The Firmware Upgrade Utility
64
Adapter Cable Firmware Upgrade Recovery
To perform an adapter cable firmware upgrade recovery, do the following:
1. Unplug the adapter cable from the computer it is connected to.
2. Slide its Firmware Upgrade Recovery Switch (located next to the RJ45
connector) to the Recover position.
3. Plug the adapter cable back into the computer.
4. From your KVM switch console, bri ng up the OSD (see page 32) and
select the F4ADM function.
5. Scroll down to FIRMWARE UPGRADE. Press [Enter].
6. Press [Y] to invoke Upgrade mode.
7. Proceed with the firmware upgrade as described in Performing the
Upgrade, starting on page 59.
8. After the upgrade comp letes and the switch restarts, unplug the adapter
cable from the computer and slide the Firmwar e Upgrade Recovery Switch
back to the Normal position.
9. Plug the adapter cable back into the computer.
65
Appendix
Safety Instructions
General
This product is for indoor use only.
Read all of these instructions. Save them for future reference.
Follow all warnings and instructions marked on the device.
Do not place the device on any unstable surface (cart, stand, table, etc.). If
the device falls, serious damage wi ll resul t.
Do not use the device near water.
Do not place the device near, or over, radiators or heat registers.
The device cabinet is provided with slots and openings to allow for
adequate ventilation. To ensure reliable operation, and to protect against
overheating, these openings must never be bl ocked or covered.
The device should never be placed on a soft surface (bed, sofa, rug, etc.) as
this will block its ventilation openings. Likewise, the device should not be
placed in a built in enclosure unless adequate ventilation has been
provided.
Never spill liquid of any kind on the device.
Unplug the device from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
The device shoul d be oper ated from the type of power source indicated on
the marking label. If you are not sure of the type of power available,
consult your dealer or local power company.
The device is designed for IT power distribution systems with 230V
phase-to-phase voltage.
To prevent damage to yo ur installation it is important that all devices are
properly grounded.
The device is equipped with a 3-wire grounding type plug. This is a safety
feature. If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not attempt to defeat the
purpose of the grounding-type plug . Always follow your local/national
wiring codes.
Appendix
66
Do not allow anything to rest on the power cord or cables. Route the
power cord and cables so that they cannot be stepped on or tripped over.
If an extension cord is used with this device make sure that the total of the
ampere ratings of all products used on this cord does not exceed the
extension cord ampere rating. Make sure that the total of all products
plugged into the wall outlet does not exceed 15 amperes.
To help pro tect you r system from sudden, transient increases and
decreases in electrical power, use a surge suppressor, line conditioner, or
uninterruptible power supply (UPS).
Position system cables and power cables carefully; Be sure that nothing
rests on any cables.
Never push objects of any kind into or through cabin et slots. They may
touch dangerous voltage points or short out parts resulting in a risk of fire
or electrical shock.
Do not attempt to service the device yourself. Refer all servicing to
qualified service personnel.
If the following conditions occur, unplug the device from the wall outlet
and bring it to qualified service personnel for repair.
The power cord or plug has become damaged or frayed.
Liquid has been spilled into the device.
The device has been exposed to rain or water.
The device has been dropped, or the cabinet has been damaged.
The device exhibits a distinct change in performance, indicating a need
for service.
The device does not operate normally when the operating instructions
are followed.
Only adjust those controls that are covered in the operatin g instructi ons.
Improper adjustment of other controls may result in damage that will
require extensive work by a qual ified technician to repair.
Do not connect the RJ-11 connector marked “UPGRADE” to a public
telecommunication netwo rk.
KL1508A / KL1516A User Manual
67
Rack Mounting
Before working on the rack, make sure that the stabilizers are secured to
the rack, extended to the floor, and that the full weight of the rack rests on
the floor. Install front and side stabilizers on a single rack or front
stabilizers for joined multiple racks before working on the rack.
Always load the rack from the bottom up, and load the heaviest item in the
rack first.
Make sure that the rack is level and stable before extending a device from
the rack.
Use caution when pressing the device rail release latches and sliding a
device into or out of a rack; the slide rails can pinch your fingers.
After a device is inserted into the rack, carefully extend the rail into a
locking position, and then slide the device into the rack.
Do not overload the AC supply branch circuit t hat provides power to the rack.
The total rack load should not exceed 80 percent of the branch circuit rating.
Make sure that all equipment used on the rack – including power strips and
other electrical connectors – is properly grounded.
Ensure that proper airflo w is provided to devices in the rack.
Ensure that the operating ambi ent temperature of the rack environment
does not exceed the maximum ambient temperature specified for the
equipment by the manufacturer
Do not step on or stand on any device when servicing other devices in a rack.
Caution: Slide/rail (LCD KVM) mounted
equipment is not to be used as a shelf or a work
space.
Appendix
68
Technical Support
International
For online technical support – including troubleshooting, documentation,
and software updates: http://support.aten.com
For telephone support, see Telephone Support, pag e iv.
North America
When you contact us, please have the following information ready beforehand:
Product model number, serial number, and date of purchase.
Your computer con fig urat ion, including operating system, revision lev e l,
expansion cards, and software.
Any error messages displayed at the time the error occurred.
The sequence of operations that led up to the error.
Any other information you feel may be of help.
Email Support support@aten-usa.com
Online
Technical
Support
Troubleshooting
Documentation
Software Updates
http://support.aten.com
Telephone Support 1-888-999-ATEN ext 4988
KL1508A / KL1516A User Manual
69
Specifications
Function KL1508A KL1516A
Computer
Connections Direct 8 16
Max. 256 (via Daisy Chain) 512 (via Daisy Chain)
Port Selection OSD (On Screen Display); Hotkeys Pushbuttons
Connectors Console Keyboard 1 x 6-pin Mini-DIN Female (Purple);
1 x USB Type A Female
Video 1 x HDB-15 Female (Blue)
Mouse 1 x 6-pin Mini-DIN Fema le (Green);
1 x USB Type A Female
KVM Ports 8 x RJ-45 Female (Black) 16 x RJ-45 Female (Black)
Daisy Chain Out 1 x DB-25 Male (Black)
F/W Upgrade 1 x RJ-11 Male (Black)
Power 1 x 3-Prong AC socket
External Mouse 1 x USB Type A Female
Switches Port Selection 8 x Pushbutton 16 x Pushbutton
KVM Reset 1 x Semi-recessed Pushbutton
F/W Upgrade 1 x Slide
Power 1 x Rocker
LCD Power 1 x Pushbutton
LCM Adjustment 4 x Pushbutton
Station 2 x Pushbutton
LEDs Port On Line 8 (Green) 16 (Green)
Selected 8 (Orange) 16 (Orange)
Power 1 (Blue)
Station ID 1 x 2 Digit 7-segment (Orange)
Lock 1 x Num Lock(Green)
1 x Caps Lock(Green)
1 x Scroll Lock(Green)
LCD Power 1 (Orange)
Emulation Keyboard / Mous e PS/2; USB (PC, Mac, Sun) ; Ser i al
Video 1280 x 1024 @ 75Hz
Scan Interval 1 - 255 sec.
I/P Rating 100-240 VAC; 50/60 Hz; 1A
Power
Consumption 17” LCD 100V, 23.2W/ 230V, 24.4W 100V, 24.5W/ 230V, 24.5W
19” LCD 100V, 23W / 230V, 23W 100V, 23W / 230V, 23W
Appendix
70
Environment Operating Temp. 0 - 40o C
Storage Temp. -20–60o C
Humidity 0 - 80% RH, Non-condensing
Physical
Properties Housing Metal
Weight 17” LCD 15.19 kg 15.20 kg
19” LCD 15.35 kg 15.36 kg
Dimensions
(L x W x H) 17” LCD 48.00 x 70.12 x 4.40 cm
19” LCD 48.00 x 70.12 x 4.40 cm
Function KL1508A KL1516A
KL1508A / KL1516A User Manual
71
Connection Tables
The following table indicates the relationship between the number of KL1508A
/ KL1516A unit s and the number of computers that they control
KL1508A
KL1516A
No. Computers No. Computers No. Computers No. Computers
1 1 - 8 9 65 - 72 17 129 - 136 25 193 - 200
29 - 16 10 73 - 80 18 137 - 144 26 201- 208
3 17 - 24 11 81 - 88 19 145 - 152 27 209 - 216
425 - 32 12 89 - 96 20 153 - 160 28 217 - 224
5 33 - 40 13 97 - 104 21 161 - 168 29 225 - 232
641 - 48 14 105 - 112 22 169 - 176 30 233 - 240
7 49- 56 15 113 - 120 23 177- 184 31 241 - 248
857 - 64 16 121 - 128 24 185 - 192 32 249 - 256
No. Computers No. Computers No. Computers No. Computers
1 1 - 16 9 129 - 144 17 257 - 272 25 385 - 400
217 - 32 10 145 - 160 18 273 - 288 26 401 - 416
3 33 - 48 11 161 - 176 19 289 - 304 27 417 - 432
449 - 64 12 177 - 192 20 305 - 320 28 433 - 448
5 65 - 80 13 193 - 208 21 321 - 336 29 449 - 464
681 - 96 14 209 - 224 22 337 - 352 30 465 - 480
7 97- 112 15 225 - 240 23 353 - 368 31 481 - 496
8113 - 128 16 241 - 256 24 369 - 384 32 497 - 512
Appendix
72
Compatible Switches
The following ATEN switches can be installed on a KL1508A / KL1516A daisy
chain:
ACS1208A / ACS1216A CS1708A / CS1716AKH1508A / KH1516A
KL1508A / KL1516A User Manual
73
OSD Factory Default Settings
The factory default settings are as follows:
Setting Default
OSD Hotkey [Scroll Lock] [Scroll Lock]
Port ID Display Position Upper Left Corner
Port ID Display Duration 3 Seconds
Port ID Display Mode The Port Number plus the Port Name
Scan Duration 5 Seconds
Scan/Skip Mode All
Screen Blanker OFF
Hotkey Command Mode ON
Hotkey [Num Lock] + [-]
Logout Timeout OFF
Beeper ON
Accessible Ports F (Full Access) For all Users on all Ports
Operation Mode Share
OSD Language English
Appendix
74
Administrator Login Failure
If you are unable to perform an Administrator login (because the Username and
Password information has become corrupted or you have forgotten it, for
example) you can clear the login information with the following procedure:
1. Power off the KL1508A / KL1516A and remove its housing.
2. Short the jumper labeled J15.
3. Power on the switch.
The on screen display will show a message informing you that the
password information has been cleared.
4. Power off the switch.
5. Remove the ju mper cap from J15.
6. Close the housing and start the KL1508A / KL1516A back up.
After you start back up, you can use the default Username and Password (see
OSD Overview, page 31) to log in.
J15
KL1508A / KL1516A User Manual
75
Optional Rack Mounting
For convenience and flexibility, three optional rack mounting kits are available
as shown in the following table:
To install the long bracket standard rack mount kit, simply replace the short L
brackets on the standard rack mount kit with the long ones, and mount the
switch according to the instructions given for Standard Rack Mounting,
page 12.
While it takes two people to perform a standard installation, with an Easy-
Installation, kit, one person can mount the switch. To install the Easy-
Installation kit, do the following:
1. Remove the standard L brackets and the side mounting brackets from both
sides of the switch.
KVM Model Bracket Type Size (cm)
KL1508M / KL1516M Standard Installation – Long 68.0—105.0
Easy Installation – Short 57.0—70.0
Easy Installation – Long 68.0—105.0
KL1508N / KL1516N Standard Installation – Long 68.0—105.0
Easy Installation – Short 63.0—70.0
Easy Installation – Long 74.0—105.0
Phillips head hex
M4L4
Appendix
76
2. Attach the left and ri ght easy-installation mounting rails to the inside of
the rack. The flange that supports the switch will be to the inside.
a) Screw the front flanges to the rack first.
b) Slide the bars with the rear flanges toward the rack until the fl anges
make contact with the rack, then screw the rear flanges to the rack.
Rear Attachment
Sliding Bracket
Support
Flange
Slide Bar
Rear Flange
Front Flange
LEFT
RAIL
RIGHT
RAIL
KL1508A / KL1516A User Manual
77
3. Slide the switch onto the support flanges. Use the screws supplied with
this package to loosely attach the front of the switch to the front of the rack
(only tighten the screws part way).
4. Slide the rear attachment sliding brackets along the slide bars until they
contact the rear of the switch, then use the screws supplied with this
package to attach the bars to the rear of the switch (tighten the screws all
the way).
Phillips I head
M4L6
Phillips I head
M4L6
Appendix
78
5. Slide the switch open and closed a couple of times to be sure that it is
properly aligned and operating smoothly. (See Opening the Console,
page 20 for opening an d closing procedures.)
6. After determ ining that the switch is properly lined up and operating
correctly, finish up by fully tightening down the partially tightened front
attachment screws inserted in step 3.
Dedicated Invocation Keys
Two dedicated keys are provid ed on the keyboard module to make it easy to
invoke Hotkey Mode and the OSD (as shown in the diagram below):
Note: These keys are toggles. Press once to invoke the feature; press again to
exit.
KL1508A / KL1516A User Manual
79
Troubleshooting
General
Problem Solution
Keyboard and/or mouse do
not work after computer
boots up.
For computers with PS/2 connectors, if you are using 2L-
520xP cables, make sure that all the connectors
(keyboard, video, and mouse) are plugged into their ports
on the computer before starting the computer. Plugging
the cables in after the computer has booted will not
resolve the problem.
When I emulate the Sun
keyboard, I can’t go into OK
Mode ([Stop] [A]).
To go into OK Mode, use the following key sequence:
1. Press and release [Ctrl].
2. Press and hold [T].
3. Press and hold [A].
4. Release [T] and [A] together.
There are ghost images on
the external monitor. The distance between the external console and the
KL1508A / KL1516A is too great. The maximum VGA
cable distance should not exceed 20m and, in some
cases, may need to be shorter. Replace the VGA cable
with one of an appropriately short length.
I can’t set the computers’
screen resolutions higher
than 1280 x 1024.
The maximum screen resolution of the KL1508A /
KL1516A’s integrated LCD monitor is 1280 x 1024. In
order to protect it from being damaged by resolutions that
are beyond its display capability, we recommend that the
screen resolutions of the connected computers be set to
1280 x 1024 or lower.
When I switch to one of the
computers on my
installation, the LCD
monitor screen goes blank.
All I see is a black screen.
The maximum screen resolution of the KL1508A /
KL1516A’s integrated LCD monitor is 1280 x 1024. The
screen resolution of the problem computer is set to
something that is too high for the KL1508A / KL1516A’s
LCD monitor to display.
To resolve the problem, connect an external KVM
console (with a monitor capable of displaying the problem
computer’s screen resolution) to the KL1508A /
KL1516A’s external console ports. Use the external
console to access the problem computer and reduce its
resolution to 1280 x 1024.
Appendix
80
Sun Systems
*These solutions work for most common Sun VGA cards. If these procedures
fail to resolve the problem, consult the manual for the Sun VGA card.
Problem Solution
Video display problems
with HDB-15 interface
systems (e.g. Sun Blade
1000 servers).
The display resolution should be set to 1024 x 768 @
60Hz.
Under Text Mode:
1. Go to OK mode and issue the following commands:
setenv output-device screen:r1024x768x60
reset-all
Under XWindow:
1. Open a console and issue the following command:
m64config -res 1024x768x60
2. Log out.
3. Log in.
Video display problems
with 13W3 interface
systems (e.g. Sun Ultra
servers).*
The display resolution should be set to 1024 x 768 @
60Hz.
Under Text Mode:
1. Go to OK mode and issue the following commands:
setenv output-device screen:r1024x768x60
reset-all
Under XWindow:
1. Open a console and issue the following command:
ffbconfig -res 1024x768x60
2. Log out.
3. Log in.
KL1508A / KL1516A User Manual
81
Limited Warranty
ALTUSEN warrants this product against defects in material or workmanship for a period of one
(1) year from the da te of purchase. If this product proves to be defective, contact ALTUSEN's
support department for repair or replacement of your unit. ALTUSEN will not issue a refund.
Return requests can not be proces sed without the original proof of purchase.
When returning the product, you mu st ship the product in its original packaging or packaging that
gives an equal degree of protection. Include your proof of purchase in the packag ing and the RMA
number clearly marked on the outside of the package.
This warranty becomes invalid if the factory-supplied serial number has been removed or altered
on the product.
This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse,
abuse, negligence or modification of any part of the pr oduct. This warranty does not cover damage
due to improper operation or maintenance, connection to improper equipment, or attempted repair
by anyone other than ALTUSEN. This warr anty does not cover products sold AS IS or WITH
FAULTS.
IN NO EVENT SHALL ALTU SEN'S LIAB ILITY EXCEED THE PRICE PAID FOR THE
PRODUCT. FURTHER, ALTUSEN SHALL NOT BE RESPONSIBLE FOR DIRECT,
INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING
FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE, OR ITS
DOCUMENTATION. ALTUSEN SHALL NOT IN ANY WAY BE RESPONSIBLE FOR,
WITHOUT LIMITATION, LOSS OF DATA, LOSS OF PROFITS, DOWNTIME, GOODWILL,
DAMAGE OR REPLACEMENT OF EQUIPMENT OR PROPERTY, AND ANY EXPENSES
FROM RECOVERY, PROGRAMMING, AND REPRODUCTION OF ANY PROGRAM OR
DATA.
ALTUSEN makes no warranty or representation, expressed, implied, or statutory with respect to
its products, contents or use of this documentation and all accompanying software, and specifically
disclaims its quality, performance, merchantability, or fitness for any particular purpose.
ALTUSEN reserves the right to revise or update its product, software or documentation without
obligation to notify any individual or entity of such revisions, or update.
For details about extended warranties, please contact one of our dedicated value added resellers.
82
Index
A
Adapter cable installation, 16
Administrator Login Failure, 74
Auto Scanning, 36, 48
Invoking Auto Scan, 48
Pausing Auto Scan, 48
Setting the Scan Interval, 48
Stopping, 49
B
Benefits, 3
C
Closing the Console, 24
Components
Front View, 7
Rear View, 10
Connection Tables, 69
Console
Closing, 24
Opening Together, 22
Separate Opening, 20
D
Daisy chaining, 18
F
Factory Default Settings, 73
Features, 3
Firmware Upgrade
Recovery, 64
Firmware upgrade
cable, 58
port, 58
recovery, 63
Firmware Upgrade Mode
Invoking, 58
Front View, 7
H
Hardware Setup, 11
Hot Plugging, 29
Hotkey, 31
Selecting the Active Port, 47
Summary Table, 54
Hotkey Mode
Exiting, 46
Invoking, 46
Hotkey Port Control, 45
I
Installation
Daisy chaining, 18
Single Station, 14
Invoking Hotkey Mode, 46
K
Keyboard Emulation
Mac, 55
Sun, 56
Keyboard port operation, 45
Keyboard Reset, 51
KL1508A,10
Rear View, 10
KL1516A
Rear View, 10
KVM Adapter Cables, 5
KVM adapter installation, 16
L
LCD OSD
Adjustment Settings, 27
Buttons, 26
Configuration, 26
KL1508A / KL1516A User Manual
83
M
Mouse Reset, 51
O
Online
Registration, iv
Opening the Console, 20
Operating Precautions, 23
OSD
Factory Default Settings, 7 3
Functions, 34
Hotkey, 31
Main Screen Headings, 33
Navigation, 33
Overview, 31
Password, 31
P
Password, 31
Port
Selection, 27
Port ID
Numbering, 30
Powering Off and Restarting, 30
R
Rack mounting
Optional, 75
Standard, 12
Rear View
KL1508A,10
KL1516A,10
Requirements
Computer, 5
Console, 5
KVM adapter cables, 5
Operating Systems, 6
OS Support, 6
RoHS, iii
S
Safety Instructions
General, 65
Rack Mounting, 67
Scan Duration, 36
Selecting the Active Port, 47
Setting the Auto Scan Interval, 36,
48
Setting the Scan Interval, 36
SJ/T 11364-2006, iii
Skip Mode, 50
T
Technical Support, 68
Telephone support, iv
Troubleshooting, 79
U
User Notice, iv