Table of Contents
Belling IDW60 User Manual
Displayed below is the user manual for IDW60 by Belling which is a product in the Dishwashers category. This manual has pages.
Related Manuals
22
·Ö Çø
DD
[]
()
BEL IDW60(7711D)
(BELLING)
1 PANTONE BLACK C
2
3 A4, A5
4
105
6710020216
BEL IDW60
12 place settings
14 place settings
half-load function
To review the section on troubleshooting Tips
will help you to solve some co mmon problems
by yourself .
Dear Customer,
Please carefully read this manual before using the
dishwasher, it will help you to use and maintain the
dishwasher properly.
Pass it on to any subsequent owner of the appliance.
This manual contains sections on safety Instructions,
Operating Instructions, Installation Instructions and
Troubleshooting Tips, etc.
The manufact urer, following a policy of constant
deve lopment and updating of the product, may
make modifications without giving prior notice.
Keep it as a refer in the later days.
If you can not solve the problems by yourself ,
please ask for the help of professional technicians.
Dishwasher Features....... ...... ... ...... ......... ... .. .. .6
A Wate r S oftener..... ... .. ... ......... ... ......... .. . ... ... 7、
Attention b efore or after loading the Di shwasher
Baskets........................ .................... ............ 12
Filtering System.............................................16
Caring for the Dishwasher..................... .........17.
B Loading the Salt into the Softener.................8、
C Fill the Rinse A id Dispenser................. ........8、
D Function of Detergent ............... ..................9、
Loading t he uppe r ..... ......... ........ . ... .....13Ba ske t
Lo ading t he Low er .............. ...... ...........1 3Ba sket
Wash Cycle Table................................... ........14
Turning on th e Appliance... ... . .. ......... ... ... ........ 1 4
Change the Programme.............. ................15....
At the end of the Wash Cycle...........................15
Befor e calling for service.......................... . .....25.
Erro r co des....... ... ......... .. .... ......... . . ... ... ... ... ..26.
Techn ica l in formation.... ... ....................... .....2 7..
Co ntrol Pan el. ... ...... ...... ...... ...... ... ......... ......... ..6
.................................. 18Installation preparation
...19Aesthetic panel's dimensio ns and installation
.... ..........21Tension adjustm ent of the door spring
.............................. 21Connection of drain hoses
......................... 22Dishwasher installation steps
About Electricity Con nectin g..... ... ......... ......... .23
Cold Water Co nnection.. ...... ... ...... .. ...... ......... 24
1
This appliance is intended to be used in household
and similar applications such as:
-staff kitchen areas in shops, offices and other
working environments;
-farm houses;
-by clients in hotels, motels and other residential type
environments;
-bed and breakfast type environments.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have b een given supervision
or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children
without supervision. For EN60335-1
This appliance is not intended for use by persons
(including children )with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge ,unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety. For IEC60335-1
This appliance is for indoor use only, for household
use only.
To protect against the risk of electrical shock, do not
immerse the unit, cord or plug in water or other liquid.
Please unplug before cleaning and maintenance the
appliance .
Use a soft cloth moisten with mild soap, and then use
a dry cloth to wipe it again.
（ ）
（ ）
When using your dishwasher,
follow the precautions listed below:
2
This appliance must be earthed. In the event of a
malfunction or breakdown, earthing will reduce the risk
of anelectric shock by providing a path of least
resistance of electric current. This appliance is equipped
with a cord having an equipment-earthing conductor
and a grounding plug.
The plug must be plugged into an appropriate outlet that
is installed and earthed in accordance with all local
codes and ordinances.
Improper connection of the equipment-earthing
conductor can result in the risk of an electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the appliance
is properly grounded.
Do not modify the plug provided with the appliance;
If it does not fit the outlet.
Have a proper outlet installed by a qualified electrician.
Do not abuse, sit on, or stand on the door or dish rack of
the dishwasher.
Do not operate your dishwasher unless all enclosure
panels are properly in place.
Open the door very carefully if the dishwasher is
operating, there is a risk of water squirting out.
Do not place any heavy objects on or stand on the door
when it is open. The appliance could tip forward.
When loading items to be washed:
1) Locate sharp items so that they are not likely to
damage the door seal;
3
2) Warning: Knives and other utensils with sharp points
must be loaded in the basket with their points down or
placed in a horizontal position.
Check that the detergent powder is empty after
completion of the wash cycle.
Do not wash plastic items unless they are marked
dishwasher safe or the equivalent.
For plastic items not so marked, check the manufacturer's
recommendations.
Use only detergent and rinse additives designed for
an automatic dishwasher.
Never use soap, laundry detergent, or hand washing
detergent in your dishwasher.
Children should be supervised to ensure that they do not
play with the appliance.
The door should not be left open, since this could increase
the risk of tripping.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
During installation, the power supply must not be
excessively or dangerously bent or flattened.
Do not tamper with controls.
The appliance is to be connected to the water mains using
new hose sets and that old hose-sets should not be reused.
The maximum number of place settings to be washed
is 14.
The maximum permissible inlet water pressure is 1MPa.
The minimum permissible inlet water pressure is 0.04MPa.
Dispose of the dishwasher packaging material
correctly.
All packaging materials can be recycled.
Plastic parts are marked with the standard
international abbreviations:
PE for polyethylene, e.g. sheet wrapping material
PS for polystyrene, e.g. padding material
POM polyoxymethylene, e.g. plastic clips
PP polypropylene, e.g. Salt filler
ABS Acrylonitrile Butadiene Styrene, e.g. Control
Panel .
Packaging material could be dangerous for children!
For disposing of package and the appliance please
go to a recycling centre. Therefore cut off the power
supply cable and make the door closing device
unusable.
Cardboard packaging is manufactured from recycled
paper and should be disposed in the waste paper
collection for recycling.
By ensuring this product is disposed of correctly, you
will help prevent potential negative consequences
for the environment and human health, which could
otherwise be caused by inappropriate waste handling
of this product.
For more detailed information about recycling of this
product, please contact your local city office and your
household waste disposal service.
DISPOSAL: Do not dispose this product as unsorted
municipal waste. Collection of such waste separately
for special treatment is necessary.
4
5
2.Quick operation guide2.Quick operation guide
For detailed operating method read the corresponding content on the instruction manual.
Compartment A:Compartment A:
With each wash cycle.
Compartment B:B:
For programmes with pre-wash only.
(Follow the user instructions!)
Mechanical indicator C. Mechanical indicator C.
Electric indicator on control panel (if provided).
Check the rinse aid level
(On models with water softener system only.)
Electric indicator on control panel (if provided).
If there is no salt warning light in the control panel
(for some models), you can estimate when to fill the salt into
the softener by the number of cycles the dishwasher has run.
Check the regeneration
salt level
Load the baskets
Select a programme
T urn on the water tap ,close the door . The machine will start working right now.
Running the dishwasher
Switch off the appliance
Turn off the water tap,
unload the baskets
Fill the detergent dispenser
Warning: wait a few minutes (about 15 minutes) before unloading the dishwasher to avoid handling
the dishes and utensils while they are still hot and more susceptible to break.
They will also dry better.Unload the appliance, starting from the lower basket.
Changing the programme
Add forgotten dishes in the
dishwasher.
Scrape off any large amount of leftover food. Soften remnants of burnt food in pans,
then load the baskets. Refer to the dishwasher loading instructions.
Press the Programme Button until the selected programme lights up.
( See the section entitled Operation instruction )
When the working cycle has finished, the buzzer of the
dishwasher will sound 8 times, then stop.
Turn off the appliance using the On/Off Button.
If the appliance is switched
off during a wash cycle.
Open the door carefully.
Hot steam may escape
when the door is opened!
WARNING!
If the appliance is switched off during a wash cycle, when switched
on again, please re-select the washing cycle and operate the dishwasher
according to the original Power-on state ).
Switch on the appliance
Open the door,press the On/Off button to switch on the appliance .
1.Open the door a little to stop the dishwasher.
2.After the spray arms stop working, you can open the door completely.
3.Add the forgotten dishes.
4.Close the door, the dishwasher will start running again after 10 seconds.
1. A running cycle can only be modified if it has been running for a short time. Otherwise the detergent
may have already been released and the water already drained. If this is the case, the detergent
dispenser must be refilled.
2. Open the door carefully,when the sprayers stop running, press the program button more than
3 seconds,the machinewill be in standby state, then you can change the
program to the desired cycle setting.
CC
AA
BB
Dishwasher FeaturesDishwasher Features
3.Operation Instruction3.Operation Instruction
Control PanelControl Panel
before using it for the first time.
To get the best performance from your dishwasher, read all operating instructions
IMPORTANTIMPORTANT
6
Back View
Front view
Dispenser
Cup Shelf
Spray arms
Filter assembly
Inlet pipe connector
Drain pipe
Lower Basket
Inner pipe
Upper Basket
1Salt Container
5
6
7
8
9
10
3
2
4
910
1
2
3
4
5
6
7
8
1.On/Off Button: To turn on/off the power supply.
3.Program Button : To Press the button to select a
wash Program.
4.Delay Button : To Press the button to delay.
5. Display screen: to show the error code,delay time etc.
Delay time,Program indicators or error codes
indicator:
Half load functions indicator:
Infall Warning Light :
Being on When faucets is not opened.
Rinse Aid indicator:
Indicates when the dispenser needs to be refilled.
Add salt indicator:
Indicates when the dispenser needs to be refilled.
2.Half load functions Button: To select Half load
functions. (With this Half load function you can
only use it when you have only about or less than
6 place setting dish wave, and you will see less
water and energy consumption , can only be used
with Intensive, Normal, ECO,Glass and 90 min .)
1122
P
334455
P1 P2 P3
P4 P5 P6
7
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the water, which would have
a detrimental or adve rse effect on the operation of the appliance.
The higher the content of these minerals and salts, the harder your water is.
The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority
can advise you on the hardness of the water in your area.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjustment in the amount of salt consumed based on the hardness of
the water used. This is intended to optimise and customise the level o f salt consumption.
WATER SOFTENER
The hardness of the water varie s from place to place. If hard water is used in the dishwasher, deposits will
form on the dishes and utensils.
The appliance is equipped with a special softener that uses a salt container specifically designed to elim inate
lime and minerals from the water.
Contact your local water board for information on the hardness of your water supply.
If your model do es no t have an y wa ter soften er, y ou m ay sk ip this section.
C lar k: Br itish de gr ee
fH : Fr ench degree
dH: German degree
dH=1.25 Cla rke=1.78 fH=0.1 78mm ol/l
1
Th e ma nuf acto ry se tting: H3 (EN 50242)
Before using your dishwasher for the first time:
A. Set the water softener
B. Add 1.5Kg dishwasher salt and then full fill the salt container with water
C. Fill the rinse aid dispense r
D. Fill in detergent
dH mmol /l
0~90~5 0~0.94 H1 0
10-20
6-11
1.0-2.0 H2 9
21-30
12-17 2.1-3. 0
H3
12
H4 20
fH
0~6
7-14
15-21
Clar ke
WA TE R HAR DNES S
Sel ect or Po si ti on S alt c onsum pti on
( gram/c ycl e)
18-22 31- 40 22-28 3. 1-4.0
41-6023-34 4.1-6.0 H5 30
H6 60
29-42
35-55 61- 98 43-69 6. 1-9.8
1. Open the door ,Switch on the appliance;
2. Press the Program button for more than 5 seconds to start the water softener
set model within 60seconds after the appliance was switched on( The Salt and
Rinse aid warning lights will be on periodically when it get in the set model );
3. Press the Program button to select the proper set according to your local environment,
the sets will change in the following sequence: H1->H2->H3->H4->H5->H6;
4. Press the Power button to end the set up model.
Please follow the steps below for adjustment in salt consumption.
1. The salt container must only be refilled when the salt warning light in the control panel comes on.
Depending on how well the salt dissolves, the salt warning light may still be on even though the
salt container is filled.
If there is no salt warning light in the control panel (for some Models),you can estimate when to fill
the salt into the softener by the cycles that the dishwasher has run.
2. If there are spills of the salt, a soak or a rapid program should be run to remove the excessive salt.
Always use th e salt intended f or use wit h dis hwash er.
The sa lt contai ner is loca ted beneath th e low er basket an d should be filled as explained
in th e fo llowin g:
Attenti on!
Only u se sa lt spe cific ally design ed for the u se in dishw ashe rs! Ev ery oth er t ype o f
salt not sp ecif ically desi gned for the use in a dishwasher, es pecia lly table salt, wi ll
damage the wate r so fte ner. In c ase o f da ma ges ca used by t he u se of unsu ita ble
salt t he m anu fa cturer does no t give any wa rran ty nor is lia ble f or any d ama ges caus ed.
Only f ill with s alt just be for e start ing o ne of th e complete wa shin g programs.
This will preve nt any grain s of salt or salty water, wh ich may ha ve be en spilled,
remain ing o n th e bo tto m of the m ac hine for any p eriod o f time, wh ich may cause
cor ro sion.
8
T he r in se aid is rel ea sed duri ng th e f inal r inse to prevent w ater fr om form ing dropl ets o n yo ur di shes , whi ch can
leave spots and streaks. I t also im proves drying by all owing water t o roll off the dishes. Your dishwasher is
de signed to u se l iq ui d r inse aids. The ri nse ai d di spenser is located i ns ide the door n ext t o t he det erg ent dispe nser.
To fill t he dis penser, o pen the cap and pour the rin se aid into the d ispenser until t he l ev el indi cator turns com plet ely
black. The vo lum e of t he rinse aid container is about 110ml.
Rinse Aid Dispenser
Function of Rinse Aid
Rinse ai d is automatical ly a dde d dur ing the l ast ri nse, e nsur ing t horough ri nsi ng, and spot a nd str eak fr ee dr ying .
Attention!
Only use branded rinse ai d f or dishwas her. Never f ill the r inse ai d disp ens er with any other substances
( e.g. Di shwasher cl eani ng agent, l iqui d de ter gent) . This w ou ld dam age the ap pl ian ce.
Ful l fi ll the s al t c on ta iner wit h wa ter,I t i s n ormal fo r a s mall a mou nt o f wa ter t o come o ut o f t he
salt con ta iner.
AAfte r the lower basket ha s be en r emo ved , unscrew an d re move the cap from the salt co ntainer.
BP lace the end of the fu nnel (su pplied) into the h ole an d int ro duc e ab out 1.5k g of dishwas her salt.
C
DA fter fill ing the container , sc re w th e ca p tight ly bac k clockwis e.
EThe salt warning li ght will stop being after the sal t containe r h as b een fil led wi th salt.
FImmediately a fter fill in g t he sal t i nt o t he s al t c ont ainer, a wa sh in g pr og ra m s ho ul d be st arte d
program Otherwis e the filter sy stem, pump or o ther important part s of th e machine may b e da mage d
by salty w ater. Thi s is out of w arra nty.
(We sug gest to u se a short
) .
9
To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.
Pour the rinse aid into the dispenser, being careful not to overfill.
Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.
Adjusting Rinse Aid Dispenser
The rinse aid dispenser has six or four settings. Always start with the dispenser
set on "4". If spots and poor drying are a problem, increase the amount of rinse
aid dispensed by removing the dispenser lid and rotating the dial to "5". If the
dishes still are not drying properly or are show spots, adjust the dial to the next
higher lever until your dishes are spot-free. The recommended setting is "4".
(Factory value is "4".)
Increase the dose if there are drops of water or lime spots on the dishes after washing.
Reduce it if there are sticky whitish stains on your dishes or a bluish film on glassware or
knife blades.
112233
1
2
3
As the rinse aid diminishes, the size of the black dot
on the rinse aid level indicator changes, as illustrated below.
Full
3 / 4 ful l
1 / 2 ful l
1 / 4 full - Should refill to eliminate spotting
Empty
Adjust lever
(Rinse)
Adjust lever
(Rinse)
When to Refill the Rinse Aid Dispenser
If there is no rinse-aid warning light in the control panel, you can estimate the amount from the colour
of the optical level indicator C located next to the cap. When the rinse-aid container is full, the whole
indicator will be dark .As the rinse-aid diminishes, the size of the dark dot decreases. You should never let
the rinse aid level fall 1 / 4 full.
during the next wash. Don't forget to replace the cap before you close dishwasher door.
Clean up any rinse aid spilled while during filling with an absorbent cloth to avoid excessive foaming
NOTE:NOTE:
NOTE:NOTE:
Detergents with its chemical ingredients are necessary to remove dirt, crush dirt and transport it out of the dishwasher.
Most of the commercial quality detergents are suitable for this purpose.
D. Function of DetergentD. Function of Detergent
MAXMAX
Proper Use of Detergent
Use only detergent specifically made for the use in dishwashers. Keep your detergent fresh and dry.
Don't put powdered detergent into the dispenser until you're ready to wash dishes.
Attention!
C (Rinse-Aid indicator) C
10
Amount of Detergent to Use
Based on their chemical composition, detergents can be split in two basic types:
Detergent tablets of different brands dissolve at different speeds. For this reason some
detergent tablets cannot dissolve and develop their full cleaning power during short
programs. Therefore please use long programs when using detergent tablets, to
ensure the complete removal of detergent residuals.
The dispenser must be refilled before the start of each wash cycle following the instructions
provided in the wash cycle table . Your dishwasher uses less detergent and rinse aid than
Conventional dishwasher. Generally, only one tablespoon of detergent is needed for
a normal wash load. More heavily soiled items need more detergent. Always add the
detergent just before starting the dishwasher, otherwise it could get damp and will not
dissolve properly.
Concentrated Detergent
Detergent Tablets
Detergent Dispenser
conventional, alkaline detergents with caustic components
low alkaline concentrated detergents with natural enzym es
Normally new pulverised detergent is without phosphate. Thus the water softener function of
phosphate is not given. In this case we recommend to fill salt in the salt container even when
the hardness of water is only 6 dH. If detergents without phosphate are used in the case of hard water
often white spots appear on dishes and glasses. In this case please add more detergent to reach
better results. Detergents without chlorine do only bleach a little. Strong and coloured spots will not
be removed completely. In this case ple ase choose a program with a higher temperature.
°
Detergents
There are 3 sorts of detergents
1.With phosphate and with chlorine
2.With phospha te and w ithout chlorine
3.Without phosphate and without chlorine
Always add the detergent just before starting each wash cycle.
Only use branded detergent aid for dishwasher.
If the lid is closed: press release button. The lid will spring open.
Deter gent tablet
Deter gent pow der
Dishwasher detergent is corrosive!
Take care to keep it out of reach of children.
Fill the detergent dispenser with detergent.
The marking indicates the dosing levels , as
illustrated on the right:
The place of main wash cycle detergent placed.
The place of pre-wash cycle detergent placed.
Please observe the manufacturers dosing and storage
Recommendations as stated on the detergent packaging.
Close the lid and press until it locks in place.
If the dishes are heavily soiled, place an additional
detergent dose in the pre-wash detergent chamber. This detergent will take effect during the pre-wash phase.
A
B
Fill in Detergent
You find information about the amount of detergent for the single programme on the last page.
Please aware, that according to the level soiling and the specific hardness of water differences are possible.
Please observe the manufacturer's recommendations on the detergent packaging.
NOTE:NOTE:
11
AABB
Cutlery with wooden, horn china or
mother-of-pearl handles
Plastic items that are not heat resistant
Older cutlery with glued parts that are not
temperature resistant
Bonded cutlery items or dishes
Pewter or cooper items
Crystal glass
Steel items subject to rusting
Wooden platters
Items made from synthetic fibres
Some types of glasses can become
dull after a large number of washes
Silver and aluminum parts have a
tendency to discolour during washing
Glazed patterns may fade if machine
washed frequently
Are not suitable Are of limited suitability
Dishes and it ems of cutlery must not lie inside one another, or cover each other.
To avoid damage to glasses, they must not touch.
Load la rge items which are most difficult to clean into the lower basket.
The upper basket is designed to hold more delicate and lighter dishware such as glasses, coffee
and tea cups
Long bladed knive s stored in an upright position are a potential hazard!
Long and/or sharp items of cutlery such as carving knives must be positioned
horizontally in the upper basket.
Please do not overload your dishwasher. This is important for good results and for
reasonable consumption of energy.
Load hollow items such as cups, glasses, pans etc. With the opening facing downwards so that
water cannot collect in the container or a deep base.
Consider buying utensils which are identified as dishwasher-proof.
Use a mild detergent that is described as 'kind to dishes'. If necessary, seek further
information from the detergent manufacturers.
For particular items, select a program with as low a temperature as possible.
To prevent damage, do not take glass and cutlery out of the dishwasher immediately
after the programme has ended.
(For best performance of the dishwasher, follo w these loading guidelines.
Features and appearance of baskets and cutlery baskets may va ry from your model.)
Scrape off any large amounts of leftover food. Soften remnants of burnt food in pans.
It is not necessary to rinse the dishes under running water.
Place objects in the dishwasher in following way:
1.Items such as cups, glasses, pots/pans, etc. are faced downwards.
2.Curved items, or ones with recesses, should be loaded aslant so that water can run off.
3.All utensils are stacked securely and can not tip over.
4.All utensils are place d in the way that the spray arms can rotate freely during washing.
Very small items should not be washed in the dishwasher as they could easily fall out of the basket.
To prevent water dripping from the upper basket into the lower basket, we recommend that you
empty the lower basket first and then the upper basket.
12
13
Folding Spikes of Lower Basket
For better stacking of pots and pans,
the spikes can be folded down as
show in the picture right.
Adjusting the Upper Basket
The height of the upper basket can be adjusted in order to
create more space for large utensils both for the upper
/lower basket. The height of the upper basket can be
adjusted by placing the wheels on different height of the
rails. Long items, serving cutlery, salad servers and knives
should be placed on the shelf so that they do not obstruct
the rotation of the spray arms..
Folding back the cup shelives
F or b etter stacking of pot s a nd p ans,
the spikes c an be folde d d own as
show in th e picture right.
The upper basket is designed to hold more delicate
and lighter dishware such as glasses, co ffee and
tea cups and saucers, as well as plates, sm all bowls
and shallow pans (as long as they are not too dirty).
Position the dishes and cookware so that they will
not get moved by the spray of water.
We suggest that you place large items and the most
difficult to clean items are to be placed into the lower
basket: such as pots, pans, lids, serving dishes and
bowls, as shown in the figure belo w. It is preferable to
place serving dishes and lids on the side of the racks
in order to avoid blocking the rotation of the top spray
arm.
Pots, serving bowls, etc, must always be pla ced top down.
Deep pots should be slanted to allow water to flow out.
Please be reminded that:
The Bottom Basket features folding spikes so that larger or more pots and pans can be loaded.
Cutlery should be placed in the cutlery rack separately from each other in the appropriate positions, and do
make sure the utensils do not nest together, this may cause bad performance.
Do not let any item extend through the bottom.
Always load sharp utensils with the sharp
point down!
14
NOTE:NOTE:
*EN 5 0242 : This programme is the test cycle. The information for comparability test
in accordance with EN 50242, as follows:
Capacity: 14 setting
Position Upper basket: upper wheels on rails
Rinse aid setting: 6
Pl:0.49w; Po:0.45w.
6.Starting a washing program6.Starting a washing program
Wash Cycle TableWash Cycle Table
NOTE:NOTE:
Means: need to fill rinse into the Rinse-Aid Dispenser.
( )
Detergent
pre/main
Detergent
pre/main
Cycle Selection
Information
Cycle Selection
Information
ProgramProgram Running
time(min)
Running
time(min)
Water
(L)
Water
(L)
Energy
(Kwh)
Energy
(Kwh)
Rinse
Aid
Rinse
Aid
Description
of Cycle
Description
of Cycle
Turning On the ApplianceTurning On the Appliance
Starting a cycle wash
Draw out the lower and upper basket, load the dishes and push them back.
It is commended to load the lower basket first, then the upper one (see the section entitled
Loading the Dishwasher ).
Pour in the detergent (see the section entitled Salt, Detergent and Rinse Aid ).
Insert the plug into the socket. The power supply is 220-240 VAC /50 HZ, the specification
of the socket is 10A 250VAC. Make sure that the water supply is turned on to full pressure.
Open the door, press the ON/OFF Button, and the display windows will light.
Press the program Button , the wash program will be changed as follows direction:
P1->P2->P3->P4->P5->P6;
If a program is selected, the LED will light. Then close the door, the dishwasher
begins to start.
1
2
3
4
5
For normally soiled loads,
such as pots, plates,glasses
and lightly soiled pans.
For heaviest soiled crockery,
and normally soiled pots
pans dishes etc with dried
on soiling.
A shorter wash for lightly
soiled loads and quick wash.
For lightly soiled crockery
and glass
5/30g
5/30g
5/30g
Wash (45 )
Rinse(50 )
Rinse(55 )
180
190
170
30
1.3
0.93
1.6
0.75
18.5
15
11
11
25g
5/30g
Pre-wash
wash(40 )
Rinse
Rinse(60 )
Drying
130
0.9 14.5
Prewash 50
Wash 60
Rinse
Rinse
Rinse 70
Drying
Prewash(45 )
Wash (55 )
Rinse
Rinse (65 )
Drying
Prewash
Wash (45 )
Rinse(65 )
Drying
This is standard programme, it is
suitable to clean normally soiled
tableware and it is the most efficient
programme in terms of its combined
energy and water consumption for
that type of tableware.
ECO
Intensive
Normal
(*EN 5 0242)
Rapid
Glass
P1
P2
P3
P6
P4
1or 2 pieces
1or 2 pieces
1or 2 pieces
1 pieces
For lightly soiled loads that
do not need excellent drying
efficiency.
90 Min
P5
Wash(65 )
Rinse
Rinse (65 )
Drying
35g
90
1.35 12.5
1 pieces
15
When the working cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then stop. Turn off
the appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher.
Wait for a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they
are still hot and more susceptible to breakage. They will also dry better.
Sw itch O ff the D ishwa sher
The program light is on but is not blinking, only in this case the programme has ended.
1.Switch off the dishwasher by pressing the ON/OFF button.
2.Turn off the water tap!
Open the door carefu lly.
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 minutes
before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.
Unloading the dishwasher
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper Basket onto
the dishes in the lower one.
A forgotten dish can be added any time before the detergent cup opens.
Add forgotten dishes.
Close the door
After the spray arms stop working, you can open the door
completely.
2
3
Open the door a little .
14
5The dishwasher will run after 10 seconds.
If you open the door , the machine will pause. The program light will
stop blinking and the buzzer will mooing every minute unless you close the door . After
you close the door ,the machine will k eep on working after 10 seconds.
during a wash cycle
Premise:
A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the
detergent may have already been re leased, and the appliance may have already drain ed the wash water.
If this is the case, the detergent disp enser must be refilled (see the section entitled " L oading the
Detergent " ).
Open the door ,press the Program bu tton , the machine will be in s tandby state,
then you can change the program to t he desired cycle setting (see the section entitled " Starting a
wash cycle. . ." ).
more than 3 seconds
1
2
If your model has broken remember function, the machine will go on to finis h the selected
program .after the power cut
It is dangerous to open the door when washing,
because the hot water may scald you.
The filter prevents larger remnants of food or other objects from getting inside the pump.
The residues may block the filt er, in this case they must be removed.
The filter system consists of a coarse filter,a flat (Main filter)
And a microfilter(Fine filter).
Food and soil particle s trapped in this filter are pulverized by a
special jet on the lower spray arm and washed down to drain.
Larger items, such as pieces of bones or glass, that could block
the drain are trapped in the coarse filter. To remove the items
caught by the filter, gently squeeze the tap on the top of this
filter and lift out.
This filter holds soil and food residues in the sump area and
prevents it from being redeposit on the dishes during wash cycle.
Main filt er
1
Coarse filter
2
Fine filter
3
2
3
1
Filter assembly
The filter efficiently
For best performance and results, the filter must be cleaned regularly. this reason, it is a good idea to
remove the larger food particles trapped in the filter after each wash cycle by rinsing the semicircular filter and
cup under running water. To remove the filter device, pull the cup handle in the upward direction.
removes food particles from the wash water, allowing it to be recycled during the cycle.
For
The dishwasher must never be used without the filter s.
Improper replacement of the filter may reduce the performance level of the appliance
and damage dishes and utensils.
Step 1 Turn the filter in anti-clockwise direction,：
Step 2 lift the filter a ssy up：
When following this procedure from step1 to step 2, the filter system will be removed;
when following it from Step 2 to Step 1, the filter system will be installed.
16
1
2
The control panel can be cleaned by using a lightly dampened cloth.
After cleaning, make sure to dry it thoroughly.
For the exterior, use a good appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on any part of the dish washer.
Protect Against Freezing
1.Cut off the electrical power to the dishwasher.
2.Turn off the water supply and disconnect the water inlet pipe from the water valve.
3.Drain the water from the inlet pipe and water valve. (Use a pan to gather the water)
4.Reconnect the water inlet pipe to the water valve.
5.Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump.
please take frost protection measures on the dishwasher in winter. Every fter wash ing cycles,
please operate as follows
time a
：
Cleaning the Filter
Cleaning The Door
To clean the coarse filter and the fine filter, use a cleaning brush. Reassemble the filter parts as shown in the figures
on the last page and reinsert the entire assembly in the dishwasher, positioning it in its seat and pressing downwards.
When cleaning the filt ers, don't knock on them. Otherwise, the filters could be
contorted and the performanc e of the d ishwash er could be decreased.
To clean the edge around the door, you should use only a soft warm, damp cloth.
To avoid penetration of water into the door lock and electrical components, do not
use a spray cleaner of any kind.
Never use a spray cleaner to clean the door panel as it may damage the door lock
and electrical components.
Abrasive agents or some paper towels should not be used because of the risk of
scratching or leaving spots on the stainless steel surface.
Cleaning the Spray Arms
If your dishwasher ca nn ot work becaus e o f the ice,
p lea se co ntac t p rof es sio na l s er vic e p erso ns .
It is necessary to clean the spray arms regularly for hard
water chemicals will clo g the spray arm jets and bearings.
- Inspect the filters for blocking after every time the dishwasher has been used.
- By unscrewing the coarse filter, you can remove the filter system. Remove any food remnants and
clean the filters under running water.
Remarks:
The entire filter assembly should be cle aned once a week.
To remove the lower spray arm, pull out the spray arm upward.
To remove the upper spray arm, hold the nut, rotate the arm
clockwise to remove it.
Wash the arms in soapy and warm water and use a soft brush to
clean the jets. Replace them after rinsing them thoroughly.
17
It is recommend that you run a wash cycle with the
dishwasher empty and then remove the plug from the
socket, turn off the water supply and leave the door of
the appliance slightly open. This will help the door
seals to last longer and prevent odours from forming
within the appliance.
If the appliance must be moved, try to keep it in the
vertical position. If absolutely necessary, it can be
positioned on its back.
One of the factors that cause odours to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this
from occurring.
Before cleaning or performing maintenance, always
remove the plug from the socket.
To clean the exterior and rubber parts of the dishwasher,
do not use solvents or abrasive cleaning products.
Only use a cloth with warm soapy water.
To remove spots or stains from the surface of the
interior, use a cloth dampened with water an a little
vinegar, or a cleaning product made specifically for
dishwashers.
Remove the Plug
No Solvents or Abrasive Cle aning
Moving t he App liance
Seal s
After every wash, turn off the water supply to the
appliance and leave the door slightly open so that
moisture and odours are not trapped inside.
After Eve ry Wash
When no t in Use for a LongTim e
18
The installation of the pipes
and electrical equipments
should be done by professionals.
Electrical Shock Hazard
Disconnect electrical power before
installing dishwasher.
Failure to do so can result in death or
electrical shock.
The installation position of dishwasher should be near the existing inlet and drain hoses and
power cord.
One side of the cabinet sink should be chosen to facilitate the connection of drain hoses of
the dishwasher.
Installation preparation
Note: please check the accompanying installation accessories(hook for aesthetic panel,screw)
●
Please caref ully read the installation instruction.
Illustrations of cabinet dimensions and installation position of the dishwasher
Preparat ions should be made before moving the dishwasher to the installation place.
Choose a place near the sink to facilitate the installation of inlet and drain hoses
(see figu re 1).
If dishwasher is in stalled at the corner of the cabinet, there should be some space
(illustrated in figure 2) when the door is opened.
2
1
Minimum space when
the door is opened
【 】Figure2
Cabinet dimensions
【 】Fig ure1
Cabinet
Dishwasher
Door of
dishwasher
Minimum space of 50mm
1The aestheti c wooden panel could be processed ac cording to the Figure 3.
T he aes thetic p anel sho uld
be processed in accordance
with the illustrat ed dimensions
【 】Figure3
●Aesthetic panel's dimensions and installation
Less than 5mm
between the top
of dishwasher and
cabinet and the
outer door aligned
to cabinet.
90 °90 °
600 mm
820mm
100
580mm
80
Space between cabinet
bottom and floor
Electrical, drain and
water supply line
entrances
(Unit: mm)
19
Installa tion of aesth etic panel
【 】Figure4a
2 Install the hook on the aesthetic wooden panel and put the hook into the slot of the outer door of
dishwasher(see figure 4a). After positioning of the panel , fix the panel onto the outer door by
screws and bolts(See figure 4b) .
Ins tallation of aesthetic
wood en pan el
【 】Figure4b
. take away the four
short screws
. pin up the four long
screws
1
2
20
Tension adjustment
of the door spring
【 】Figure5
Tension adjustment of the door spring
●
Connection of drain hoses
●
The door springs are set at the factory to t he proper tension for the outer door.
If aesthetic woode n pan el are installed, you will have to adjust the door spring tension.
Rotate the adjusti ng screw to drive the ad justor to strain or relax the steel cable
(see figure 5 ).
Door spring tension is correct when
the door remains horizontal in the
fully opened position yet rises
to a close with the slight lift of a
finger.
，
21
Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink, making sure to
avoid bending or crimping it. The top of the hose must be less than 1000mm.
A
Counter
Front
Drain pipe
NOTE
The top of the hose
must be less than
1000mm.
φ40 mm
B
22
Dishwasher installation steps
●
1
2
.
3 .
4 .
5 .
6
7
8
Install the furn iture d oor to the outer door of the dishwasher using the brackets p rovided. Refer
to the template for positioning of the brackets.
Adjust the tension of the door spri ngs by using an All en key turning in a clockw ise m otion t o
tighten the left and right door springs. Failure to do this could cause damage to your di shwas her
(Illustration 2)
Connect the inlet hos e to the cold water supply
Connect the drain ho se. Refer to diagram (Figure 6)
Connect the po wer cord
Affix the condensation strip under the work sur face of cabinet. Please ensure the condensation
strip is flush with edge of work surface.
Pla ce the dishwasher into position.(Illustration 4)
Level the dishwasher. The rear food can be adjusted from the fro nt of the dishwasher by tu rning
the A llen sc rew in the middle o f the base of dishwasher use a n Allen key (Illustration 5 A). To adjust
the fr ont feet, use a flat screw driver and turn the fron t feet un til the dishw asher is level (Illustration 5B).
9 The dishwasher must be secured in place. There are two w ays to do this:
A. No rmal work s urface:Put th e insta llation hook into the slot of the side plane and se cure it to the
work sur face with the wo od screws (Illustratio n 6).
B. Marble or granite work top:Fix the side w ith Screw. (Illustration 7 ).
【Figure 7】
23
Dis hwash er must be level for prope r dish rack operation and wash perfor mance.
Place a spiri t level on doo r and rack tr ack inside the tub a s show n to check t hat the
dishwa sher is level.
level th e dish washe r by adjusting the three levelling legs individ ually.
When level th e dishwasher, please pay attention not to let the dishwasher tip over.
1
2
3
Illustration of feet adjustment
【 】Figure 8
NOTE:
The maximum adjustment
height of t he feet is 50 mm.
Ensure the voltage and frequency o f the power being corresponds to
those on the rating plate. Only insert the plug into an electrical socket which is earthed
properly. If the electrical socket to w hich the appliance must be connected is not
appropriate for the plug , replace the socket, rather than using a adaptors or the like as
they could cause overheating and b urns.
Please look at the rating label to know the rating voltage and connect the dishwasher to the appropriate power supply.
Use the required fuse 10 amp, time delay fuse or circuit breaker recommended and provide separate circuit serving
only this appliance.
Ch eck le ve l s ide t o side
Spirit l evel
C hec k l eve l Front t o B ack
For personal safety:
Do not use an extension cord or an adapter plug
with this appliance.
Do not, under any circumstances, cut or remove the
earthing
Connection from the power cord.
24
Positioning the Appliance
How to Drain Excess Water From Hoses
If the sink is 1000 higher from the floor, the excess water in hoses cannot be drained directly
into the sink. It will be necessary to drain excess water from hoses into a bowl or suitable
container that is held outside and lower than the sink.
Water Outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.
Ensure that the water inlet hose is not kinked or squashed.
The foll owing things shoul d be c hecked before starting the dishwasher.
Syphon Connection
Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink, making sure to
avoid bending or crimping it. The top of the hose must be less than 1000mm.
The content of t his manual i s very helpful to the users.
After installation, please make sure t o keep this manual .
Extension Hose
If you need a drain hose extension, make sure to use a similar drain hose.
It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be reduced.
1The dishwasher is le vel and fixed prope rly
2The inlet valve is open
3There is a leakage at the connections o f the conduct s
4The wires are tightly connected
5The power is switched on
6The inlet and drain hoses are knotted
7All packing ma terials and p rinting s shou ld be t aken out fro m the dishwasher
Position the a ppliance in the desired location. The back should rest against the wall behind it, and the sides,
along the adjacent cabinets or walls. The dishwash er is equipped with water supply and drain hoses that can
be positioned either to the right or the left sides to facilitate proper installation.
Connect the cold water supply hose to a threa ded 3/4(inch) connector and make sure
that it is fastened tightly in place .
If the water pipes are new or have not been used for an extended period of time, let the
water run to make sure that the water is clear. This precaution is needed to avoid the
risk of the water inle t to be blocked and damage the appliance.
Please clo se the hydrant after using.
25
Fuse blown, or the
circuit breaker acted
Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Spilled rinse-aid Always wipe up rinse-aid spills immediately.
Hard water minerals
The affected items are
not corrosion resistant.
The lid of the softer
is loose
A sp ay arm is
knocking against
an item in a basket
r
Items of crockery
are loose in the
wash cabinet
This may be caused
by on-site installation
or the cross-section of
the piping.
A programme was not
run after dishwasher
salt was added.
Traces of salt have
gotten into the wash cycle.
To clean the interior, use a damp sponge with
dishwasher detergent and wear rubber gloves.
Never use any other cleaner than dishwasher
detergent for the risk of foaming or suds.
Always run the quick wash programme .
without any crockery in the dishwasher and
without selecting the Turbo function (if present),
after adding dishwasher salt.
Check the lip .Ensure the fix is fine.
Interrupt the programme, and rearrange the items
which are obstructing the sp ay arm.r
Interrupt the programme,
and rearrange the items of crockery.
This has no influence on the dishwasher function.
if in doubt, contact a suitably qualified plumber.
Detergent with
colourant was used
Make sure that the detergent is the one without
colourant.
Improper detergent
Make sure the dishwasher is turned on and the door is
closed securely.
Check that the water supply is connected properly and
the water is turned on.
Make sure to close the door properly and latch it.
Make sure the power cord is properly plugged into the
wall socket.
Power supply is not
turned on
Water pressure is low
Door of dishwasher
not properly closed.
Kink in drain hose
Filter clogged
Kitchen sink clogged
Check drain hose.
Check coarse the filter
(see section titled )" Cleaning The Filter "
Check the kitchen sink to make sure it is draining well.
If the problem is the kitchen sink not draining ,you may
need a plumber rather than a serviceman for dishwashers.
Use only the special dishwasher detergent to avoid suds.
If this occurs, open the dishwasher and let suds evaporate.
Add 1 gallon of cold water to the tub. Close and latch the
dishwasher, then select any cycle. Dishwasher will drain
out the water at the first step.Open the door after draining
is stop and check if the suds is disappeared.
Repeat if necessary.
26
The dishes were not
loaded correctly.
See notes in " Loading the Dishwasher Baskets ".
Select a more intensive programme.
See" Wash Cycle Table ."
Use more detergent, or change your detergent.
Rearrange the items so that the sp ay can rotate freely.r
Clean and/or fit the filter combination correctly.
Clean the sp ay arm jets. See "Cleaning the Spray
Arms".
r
Use less detergent if you have soft water and select
a shortest cycle to wash the glassware and to get
them clean.
Use a mild abrasive cleaner to eliminate those marks.
Re-loading the dishes properly.
Load the dishwasher as suggested in the directions.
Increase the amount of rinse-aid/refill the rinse-aid
dispenser.
Do not empty your dishwasher immediately after
washing. Open the door slightly so that the steam can
escape. Begin unloading the dishwasher only once t
he dishes are barely warm to the touch. Empty the low
basket first. This prevents water form dropping off
dishes in the upper basket.
In short program the washing temperature is lower.
This also lowers cleaning performance. Choose
a program with a long washing time.
Water drainage is more difficult with these items.
Cutlery or dishes of this type are not suitable for
washing in the dishwasher.
The programme was
not powerful enough.
Not enough detergent
was dispensed.
Items are blocking
the path of sp ay arms.r
The filter combination
in the base of wash
cabinet is not clean or
is not correctly fitted.
This may cause
the sp ay arm jets
to get blocked.
r
Combination of soft
water and too much
detergent.
Aluminum utensils
have rubbed against
dishes.
Dishes block
detergent cups.
Improper loading
Too little rinse-aid
Dishes are removed
too soon
Wrong program
has been selected
Use of cutlery with
a low-quality coating
If overflow occurs, turn off the main water supply before calling a service.
If there is water in the base pan because of an overfill or small leak,
the water should be removed before restarting the dishwasher.
When some malfunctions come on, the appliance will display error codes to warn you:
Longer inlet time.
Faucets is not opened, or water intake is
restricted,or water pressure is too low.
E1
Not reaching required temperature
Mulfunction of heating element.
E3
Overflow.
Some element of dishwasher leaks .
E4
27
Height : 815mm
Width : 598 mm
Depth : 550mm( )
with the door closed
Water pressure: 0.04-1.0MPa
Power supply: see rating label
Capacity: 14 place settings
Large serving bowl
Small serving bowl
Medium serving bowl
Glasses
Saucers
Cups
Oval platter
Dinner plates
Soup plates
Dessert dishes
TeaspoonsTeaspoons
4
Soup spoons
2Forks
1
Serving forks
8
Serving spoons
6
Knives
5
3
Dessert spoons
7
Gravy ladles
Loading the baskets according to En50242: Loading the baskets according to En50242:
1.Upper basket:1.Upper basket:
2.Lower basket:2.Lower basket:
3.Cutterly basket:3.Cutterly basket:
Information for comparability tests in accordance
with EN 50242
Information for comparability tests in accordance
with EN 50242
Capacity: 14 place settingsCapacity: place settings14
Position of the upper basket: lower position
Position of the upper basket: lower position
Programme: ECOProgramme: ECO
Rinse aid setting: 6Rinse aid setting: 6
Softener setting: H4 Softener setting: H4
IN
IN
77
77
99
88
88
1010
77
77
223333
6666
ShelfShelf
11
33
66
11
33
33
33
22
33
22
11
11
11
33
33
4
ShelfShelf
33
44
77
11111111
11
11
111111
1111111111
22222222
33333333
444444
44444444
4444444444
44
5555
5555
55555555555555555555
88
Note: Please place the light flat wares on the shelf. The
total weight is less than 1.5kg.
Note: Please place the light flat wares on the shelf. The
total weight is less than 1.5kg.
28
29
14
A++
266 kWh
0.93 kWh
0.45 W
0.49 W
3080 liter
A
190 min
81.5 cm
59.8 cm
55 cm
1930 W
Sheet of household dishwasher according to EU Directive 1059/2010:
Manufacturer
Type / Description
Standard place settings
Energy efficiency class
Annual energy consu mption
Energy consu mption of the standard cleaning cycle
Power consumption of off-mode
Power consumption of left-on mode
Annual water consumption
Drying efficiency class
Standard cleaning cycle
Program duration of the standard cleaning cycle
Noise level
Mounting
Height
Width
Depth (with connect ors)
Power consumption
Rated voltage / frequency
A + + + (highest efficiency) to D (lowest efficiency)
Energy consu mption 266 kWh per year, based on 280 standard cleaning cycles using cold water fill and
the consumption of the low power modes. Actual energy consumption will depend on how the appliance is used.
“ ”
Water consumption 3080 litres per year, based on 280 standard cleaning cycles. Actual water consumption
will depend on how the appliance is used.
“ ”
A (highest efficiency) to G (lowest efficiency)
This program is suitable for cleaning soiled normally soiled tableware and that it is the
most efficient programme in terms of its combined energy and water consu mption for
that type of tableware.
The device meets the European standards and the directives in the current version at delivery:
- LVD 2006/95/EC
- EMC2004/108/EC
- EUP 2009/125/EC
The above values have been measured in accordance with standards under specified operating conditions.
Results may vary greatly according to quantity and pollution of the dishes, water hardness,
amount of detergent, etc.
The manual is based on the European Union's standards and rules.
Technical Data Sheet
NOTE：
ECO 45℃
4 dB(A) re 1 pW
build under
220-240 V~ 50 Hz
Water pressure (flow pressure) 0.4-10 bar = 0.04-1 MPa
Could be built-in Yes
BELLING
BEL IDW60
7
DISHWASHER FEATURES
Additional features of this dishwasher are:
Error alarm
.
To alert you to any errors or problems with the
program while it is running
14 place settings
Be sufficient for normal use.
6 wash programs
You can choose desired program according to the
soiled level.
Adjustable upper basket
.
Flexible dish loading available. Adjust the upper
basket for large or awkward loads
Stainless steel tub
. No need to worry about staining
Rinse aid Warning Indicator
.
If the rinse aid is running low, the warning indicator
will light on the panel, alerting you to top it up.
This ensures the best results from your machine
Overflow protection
.
Your dishwasher has an overfill protection
program which automatically shuts off the
inlet valve and starts the drain pump if the
water is overflowing
Time delay feature
This allows the start of the programme to be delay
between 1 and 24 hours, enabling you to benefit
fully from cheaper electricity! Or just to benefit
from the convenience of the programming
finishing when you want to.
SS
1414
66
Broad applied voltage
The broad scope of the applied voltage ,reduce
the code of electric condition.
Salt Warning Indicator
.
If the salt is running low, the warning indicator will
light on the panel, alerting you to top it up. This
ensures the best results from your machine
This symbol on the product or in the instructions means that your electrical and electronic equipment should
Be disposed at the end of its life separately from your household waste. There are separate collection systems
for recycling in the EU.
For more information, please contact the local authority or your retailer where you purchased the product.
Customer Care
In case of difficulty within the UK and Northern Ireland, please
call the customer care help line on 08
Stoney lane,prescot,Merseyside,L35 2XW
44 815 3746