Bouncepad Wing Lite User Manual
Displayed below is the user manual for Wing Lite by Bouncepad which is a product in the Tablet Security Enclosures category. This manual has pages.
Related Manuals
Sheet Code: BP-IM-071_REV1
Release Date: 24/05/2021
Copyright 2016 Spotspot Ltd. (T/A
Bouncepad) all rights reserved.
Condential, no part of this publication
may be reproduced or transmitted in any
form without the written permission of the
copyright holder.
Wing - Slim
Assembly Instructions
In the Box Fixings
List
Tools Required:
All tools provided
Mounting Arm
Access Panel
Mounting
Bracket
Bouncepad
Lock
Mounting Arm
Case Back
Faceplate
8x M4x8mm
Buttonhead
screw
10x M6x10mm
Buttonhead
screw
*xings to attach the stand to the
ground are not provided.
Position the Mount Bracket on the
ground where the stand is to be
located.
1
If using a hard-wired power supply,
feed the cable into the Mounting
Arm.
56Locate the Mounting Arm onto the
Mount Bracket as shown.
Minimum:
or
380mm 15”
2Mark your mounting surface, then
drill (as appropriate to your chosen
xing method).
*xings to attach the
product to the ground
are not provided.
3
4
Secure the Mount Bracket to your
mounting surface, with your chosen
xing method.
Remove the Access Panel from the
Mounting Arm. Store all parts safely
aside for use later.
*shown for illustrative purposes.
*Fitted into Case by Bouncepad.
**Lock available as optional extra
(at additional charge).
14 15
Locate and secure the
Access Panel to the
Mounting Arm.
For added security, install
a Kensington security
cable.
8 9
11 12
Remove the Faceplate from the Case
Back. Store this aside.
Locate and secure the Case Back to
the Mounting Arm, with 4x M6x10mm
screws. Ensure good Case alignment.
Install the tablet and the tablet
power cable. Connect the tablet to a power source.
Installation is
complete.
16
*The Case is congured to your order.
If requiring a dierent tablet
conguration, please contact us.
7Secure the Mounting Arm to the
Mount Bracket, with 5x M6x10mm
screws.
Complete the separate tablet setup
document - specic to your tablet,
device orientation & locking method.
10
*Kensington security
cable not provided.
13 Secure the Faceplate shut with your
chosen locking method.
*If requiring an upgrade to a
keyed Case, please contact us.
Sheet Code: BP-IM-074_REV0
Release Date: 15/06/2021
Copyright 2016 Spotspot Ltd. (T/A
Bouncepad) all rights reserved.
Condential, no part of this publication
may be reproduced or transmitted in any
form without the written permission of the
copyright holder.
Wing - Tablet Setup
Assembly Instructions
Tools Required:
All tools provided
Follow the tablet specic assembly guide
shown for locating your tablet setup kit.
Take care to ensure correct thread
engagement between the xings & tablet
supports.
!
*Your congured product may not be representative of the shown illustration.
**The Bouncepad lock is an optional extra (at additional charge).
M4x8mm
Buttonhead
screw
Tablet support
Follow the shown
guide if installing your
device in Landscape.
Follow the shown
guide if installing your
device in Portrait.
Device:
iPad Pro 12.9” (Gen3,4,5)
Follow the shown
guide if installing your
device in Landscape.
Follow the shown
guide if installing your
device in Portrait.
TDL16
TDL17
TDL16
TDL17
TDL16
TDL16
TDL16
TDL16
TDL16
TDL16
TDL17
TDL17