To Start Menu
How to Use This Manual
Quick Reference Guide
Table of Contents
Safety Instructions
Before Use
User’s Manual (Operation)
Projecting an Image
Useful Functions Available During a Presentation
- Useful Functions Available During a Presentation
Setting Functions from Menus
Installation Manual (Installation and Maintenance)
Installation
Connecting to a Network
Maintenance
Appendix
Appendix

Canon WX6000 User Manual

Displayed below is the user manual for WX6000 by Canon which is a product in the Data Projectors category. This manual has pages.

Related Manuals

Canon EF 85mm f/1.8 USM Manual

Canon 5D + EF 24-105mm + EF 100-400mm Kit Manual

Canon 105 Manual

Canon MF3010 Manual

Canon LBP7010C Manual

Installation

Connecting to a Network

Maintenance

Appendix

Index

AppendixInstallation Manual

Projecting an Image

Safety Instructions

Before Use

Table of Contents

Setting Functions from Menus

Useful Functions Available

During a Presentation

User’s Manual

ENG

MULTIMEDIA PROJECTOR

User’s Manual /

Installation

Manual

How to Use This Manual

Thank you for purchasing a Canon projector.

The WUX5000 / WUX4000 / WX6000 / SX6000 Multimedia Projector (hereinafter referred

to as “the projector”) is a high-performance projector that is capable of projecting a high-

resolution computer screen and high-quality digital image on a large screen.

User’s Manual (Operation) / Installation Manual (Installation and Maintenance) (This Man-

ual)

This manual combines the user’s manual and the installation manual for the WUX5000 /

WUX4000 / WX6000 / SX6000 Multimedia Projectors. The user’s manual provides informa-

tion on how to use the projector. The installation manual describes how to install the pro-

jector and connect to a network, as well as perform maintenance. Read this manual

thoroughly to make the most of your projector. Installation of the projector should be per-

formed by a qualified technician. Contact the Canon Customer Support Center for further

information.

Symbols Used in This Manual

Meanings of the symbols used in this manual are as follows.

A precaution about operation or restriction is given here.

These descriptions are for WUX5000 / WUX4000.

These descriptions are for WX6000 / SX6000.

These descriptions are for WUX4000.

These descriptions are for WX6000.

Symbols of Button Operations

The projector can be operated using the buttons on the remote control or on the

side of the projector. The remote control allows you to operate all functions of

the projector. In this document, the button’s operations are shown as below.

Indicate the buttons to be pressed

Adjusting the Image Size

The size of the projected image can be adjusted b

remote control or the LENS button on the projector.

Change the projector installation position if your de

adjust it with the zoom function. (P155)

1Press either the ZOOM button on the remote control

Remote control Projector

Push twice

Operation of buttons on side of

projector

Remote control button operation Remote control

How to Use This Manual

Please note that enlarging or reducing the size of an image for commercial pur-

poses or public presentation may infringe on the legally protected copyright or the

About Trademarks

• Ethernet is a registered trademark of Xerox Corporation.

• Microsoft, Windows, Windows XP, Windows Vista and Windows 7 are registered

trademarks or trademarks of Microsoft Corporation in the United States and / or

other countries.

• Mac, Mac OS and Macintosh are trademarks of Apple Inc., registered in the United

States and / or other countries.

• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or

registered trademarks of HDMI Licensing, LLC.

• PJLink is a registered trademark, or an application has been submitted for trade-

mark, in Japan, the United States and / or other countries or regions.

Quick Reference Guide

This Quick Reference Guide will help you find functions that make full use of the projector

and are useful for producing an attractive presentation, etc.

Connecting to the Computer (P47 - P51)

Connecting to AV Equipment (P52 - P55)

Starting Projection (P56 - P58)

Selecting an Input Signal (P59 - P60)

Adjusting the Image Size and Focus (P71 -

P73)

Adjusting Keystone Distortion (P76)

Adjusting Aspect Ratio (P63 - P70)

Eliminating Flickers from Computer Screen

and Adjusting Positional Shift (P96, P97)

Projecting an Image on a Greenboard (P103)

Selecting an Image Mode Suitable for the

Projecting Image (P109)

Making Fine Color Adjustments (P114)

Removing Noise (P116)

Temporarily Blacking Out an Image (P82)

Freezing the Picture (P82)

Adjusting the Volume (P83)

Muting the Sound (P83)

Zooming an Image (P84)

Showing the Elapsed Time (P85)

Resetting Password (P128)

Initializing the Network Setting (P176)

Resetting to the Default Setting (P140)

Using the Power Saving Mode (P120)

Turning on the Projector by Connecting the

Power Cord (P121)

Disabling the Beep During Operation (P122)

Disabling Buttons (P123)

Hiding Guide Messages (P126)

Setting a Password (P128)

Reducing the Lamp Brightness (P119)

Displaying Test Pattern (P138)

Selecting Audio In Terminal (P139)

Connecting the Projector

Projecting an Image

Adjusting the Image

Adjusting Colors and Image Quality

Producing a Presentation

Changing the Remote Control Channel

(P124)

Resetting Projector Setting

Miscellaneous Functions

Table of Contents

How to Use This Manual ..............................................................................................2

Quick Reference Guide................................................................................................4

Safety Instructions.....................................................................................................12

Safety Precautions.................................................................................................................... 13

CAUTION ON HANGING FROM THE CEILING ...................................................................... 13

■ READ AND KEEP THIS OWNER’S MANUAL FOR LATER USE. ..................................... 14

AC Power Cord Requirement ................................................................................................... 16

Federal Communication Commission Notice............................................................................ 17

Canadian Radio Interference Regulations ................................................................................ 17

Precautions for Use .................................................................................................................. 18

Precautions for Installation ....................................................................................................... 19

Precautions on the lamp ........................................................................................................... 21

Precautions for the batteries of the remote control ................................................................... 22

Before Use ........................................................................................................ 25

Supplied Accessories ................................................................................................26

■ Installing Remote Control Batteries ................................................................................. 27

Preparing the Remote Control ..................................................................................29

■ Remote Control Operating Range ................................................................................... 29

■ When a remote control is connected using a cable (WX6000 / SX6000)........................30

Part Names..................................................................................................................31

Main Unit (The illustration shows WUX5000.) ..........................................................................31

■ Front Side ........................................................................................................................ 31

■ Rear Side ......................................................................................................................... 32

■ Bottom Side .....................................................................................................................32

Remote Control......................................................................................................................... 34

■ RS-RC04 .......................................................................................................................... 34

■ RS-RC05 .......................................................................................................................... 36

Side Control .............................................................................................................................. 38

■ LED Indicator Displays .................................................................................................... 39

Input Terminal...........................................................................................................................40

User’s Manual (Operation) ............................. 43

Projecting an Image ......................................................................................... 45

Steps for Connecting the Projector and Projecting an Image ...............................46

Connecting the Projector ..........................................................................................47

Connecting the Projector to a Computer .................................................................................. 47

■ Connecting to RGB Monitor Output Terminal (Analog Connection)................................ 47

■ Connecting to DVI Monitor Output Terminal (Digital Connection)................................... 50

■ Connecting with a HDMI Cable (Input signal type: [HDMI] – P59) ................................. 51

■ Outputting Audio to Speakers ......................................................................................... 51

Table of Contents

Connecting to AV Equipment ................................................................................................... 52

■ Connecting to Digital Video Output Terminal (Digital Connection) ................................ 52

■ Connecting to Analog Video Output Terminal (Analog Connection) .............................. 53

■ Outputting Audio to Speakers......................................................................................... 55

Starting Projection..................................................................................................... 56

■ When the Language Selection Screen Appears............................................................. 57

■ When the Password Input Screen Appears.................................................................... 58

■ When “No signal” Appears ............................................................................................. 58

■ When Notebook Computer Screen Does Not Appear .................................................... 58

■ Adjusting Image.............................................................................................................. 58

Changing Notebook Computer Screen Output......................................................................... 58

■ Turning on External Monitor Output ................................................................................ 58

Selecting an Input Signal (INPUT) ............................................................................ 59

■ Types of Input Signals .................................................................................................... 59

■ Selecting an Input Signal ................................................................................................ 60

Adjusting the Image................................................................................................... 61

Setting the Display Resolution of the Computer....................................................................... 61

■ Windows 7.......................................................................................................................61

■ Windows Vista................................................................................................................. 61

■ Windows XP .................................................................................................................... 61

■ Mac OS X ........................................................................................................................62

AUTO PC ................................................................................................................................. 62

■ Performing the Auto PC Function.................................................................................... 62

Selecting Screen Aspect and Aspect ....................................................................................... 63

■ Selecting Screen Aspect ................................................................................................ 63

■ Selecting Aspect Ratio.................................................................................................... 69

Adjusting the Image Size.......................................................................................................... 71

Adjusting the Focus.................................................................................................................. 73

Adjusting the Image Position....................................................................................................74

■ Resetting the Position ..................................................................................................... 75

Adjusting Keystone Distortion .................................................................................................. 76

■ Resetting the Keystone Adjustment................................................................................ 77

Selecting an Image Mode .......................................................................................... 78

■ Image Modes .................................................................................................................. 78

■ How to Select an Image Mode........................................................................................ 79

Turning Off the Projector .......................................................................................... 80

Useful Functions Available During a Presentation ....................................... 81

Useful Functions Available During a Presentation................................................. 82

Temporarily Blacking Out an Image ...................................................... BLANK ...................... 82

Freezing the Picture .............................................................................. FREEZE .................... 82

Adjusting the Volume ............................................................................ VOL........................... 83

Muting the Sound .................................................................................. MUTE........................ 83

Zooming an Image ................................................................................ D.ZOOM.................... 84

Showing the Elapsed Time (WUX5000 / WUX4000) ............................P-TIMER ................... 85

Table of Contents

Setting Functions from Menus........................................................................ 87

How to Use Menus .....................................................................................................88

■ Menu Configuration ......................................................................................................... 88

■ Basic Menu Operations ................................................................................................... 90

Setting Display Status ...............................................................................................93

Selecting an Image Projection Mode ........................................................................................ 93

Automatic Display Adjustment (WX6000 / SX6000) ................................................................. 94

Selecting an Input Signal Type (Analog PC) ............................................................................ 94

Selecting an Input Signal Type (Component) (WUX5000 / WUX4000) .................................... 95

Adjust Input Signal Type (Analog PC) Total Dots.....................................................................95

Adjust Input Signal Type (Analog PC) Tracking ....................................................................... 96

Adjust Input Signal Type (Analog PC) Horizontal Position .......................................................96

Adjust Input Signal Type (Analog PC) Vertical Position ........................................................... 97

Adjust Input Signal Type (Analog PC) Horizontal Pixels .......................................................... 97

Adjust Input Signal Type (Analog PC) Vertical Pixels...............................................................98

Selecting HDMI Input Level ......................................................................................................98

HDMI Color Format................................................................................................................... 99

Select HDMI Over Scan..........................................................................................................100

Performing Progressive Processing ....................................................................................... 101

Selecting a Menu Position ......................................................................................................102

Correcting the Screen Color ................................................................................................... 103

Reversing Projection............................................................................................................... 104

No Signal Screen.................................................................................................................... 105

Screen When Blank ................................................................................................................ 106

Selecting a Logo at Startup ....................................................................................................106

Selecting Aspect Ratio of Screen ........................................................................................... 107

Adjusting Keystone Distortion (WX6000 / SX6000) ................................................................ 108

Image Shift Adjustment (WX6000 / SX6000).......................................................................... 108

Selecting an Image Quality......................................................................................109

Image Adjustment................................................................................................................... 109

Saving the Desired Image Quality .......................................................................................... 110

Adjusting the Brightness ......................................................................................................... 111

Adjusting the Contrast ............................................................................................................112

Adjusting the Sharpness......................................................................................................... 113

Performing Gamma Correction ............................................................................................... 113

Adjusting Color ....................................................................................................................... 114

Correcting the Image According to the Ambient Light ............................................................ 115

Noise Reduction .....................................................................................................................116

Dynamic Gamma .................................................................................................................... 116

Memory Color Correction........................................................................................................117

6-axis Color Adjust (Detailed Color Adjustment) .................................................................... 117

Detailed Gamma Correction ................................................................................................... 118

Table of Contents

Reducing the Lamp Brightness (WUX4000) .......................................................................... 119

Resetting the Image Adjustment Settings .............................................................................. 119

Setting Various Functions....................................................................................... 120

Selecting the Power Management Mode ............................................................................... 120

Skip the POWER Button Operation........................................................................................ 121

Enabling / Disabling the Beep ................................................................................................ 122

Key Repeat (WX6000 / SX6000)............................................................................................ 122

Prohibiting Operations............................................................................................................ 123

Main Unit and Remote Control Channel Settings................................................................... 124

Selecting a Display Language................................................................................................ 125

Showing / Hiding the Guide Screen ....................................................................................... 126

Showing / Hiding the Input Status .......................................................................................... 127

Selecting the HDMI Input ....................................................................................................... 127

Setting a Password ................................................................................................................ 128

Registering a Password ......................................................................................................... 129

Prohibiting Operation of the Lens (WUX5000 / WUX4000).................................................... 130

Lens Shift Reset ..................................................................................................................... 131

Extending the Menu Display Time.......................................................................................... 132

Showing / Hiding the High Temperature Warning Icon .......................................................... 133

Reducing Flickering (WUX5000 / WUX4000)......................................................................... 134

Gamma Restore (WX6000 / SX6000) .................................................................................... 134

Lamp Warning Display (WX6000 / SX6000) .......................................................................... 135

Resetting the Lamp Counter .................................................................................................. 135

■ About the Display of the Lamp Counter........................................................................ 136

Filter Warning Display (WX6000 / SX6000) ........................................................................... 137

Resetting the Air Filter Counter (WX6000 / SX6000) ............................................................. 137

Displaying Test Pattern (WX6000 / SX6000) ......................................................................... 138

Selecting Audio In Terminal (WX6000 / SX6000) .................................................................. 139

Locking Installation Related Functions (WX6000 / SX6000).................................................. 139

Resetting to the Default Setting.............................................................................................. 140

Checking Projector Information ............................................................................. 141

Installation Manual

(Installation and Maintenance) .................... 143

Installation ...................................................................................................... 145

Installation Precautions........................................................................................... 146

Precautions When Carrying the Projector .............................................................................. 146

Installation Precautions .......................................................................................................... 146

Precautions When Carrying and Transporting the Projector.................................................. 146

■ When using mounted on the ceiling ............................................................................. 148

Table of Contents

■ Install facing in the correct direction ............................................................................. 148

Installation Procedure..............................................................................................149

Selecting the Projection Method and Installation Location .................................150

■ Ceiling Mounting or Rear Projection.............................................................................. 150

■ Adjusting the projection position when installed on the floor ........................................ 150

Installing / Removing the Lens Unit .......................................................................151

■ Installing the Lens Unit .................................................................................................. 151

■ Removing the Lens Unit ................................................................................................ 155

Setting Up the Projector ..........................................................................................156

■ Positioning the Projector in Front of the Screen ............................................................ 156

■ Relationship Between Image Size and Projecting Distance .........................................156

■ Lens Shift Function ........................................................................................................ 160

Connecting to AV Equipment..................................................................................162

■ Connectable Equipment and Input Terminals............................................................... 162

■ Connection Terminal and Connection Cable ................................................................ 164

Connecting to a Network ............................................................................... 165

Preparing the Remote Control ................................................................................166

Connection Methods...............................................................................................................166

Setting an IP Address .............................................................................................................167

■ Windows 7 ..................................................................................................................... 167

■ Windows Vista ............................................................................................................... 168

■ Windows XP................................................................................................................... 169

■ Mac OS X....................................................................................................................... 170

■ Resetting the IP Address Setting of the Computer........................................................ 170

Network Settings on the Projector .........................................................................171

Locking the Network Settings ................................................................................................. 171

Turning the Network Function On / Off ................................................................................... 172

Setting a Network Password................................................................................................... 173

Registering a Network Password............................................................................................ 173

Turning the PJLink Function On / Off .....................................................................................174

Turning DHCP Function On / Off ............................................................................................ 175

TCP / IP Setting ...................................................................................................................... 175

Initializing Network Settings....................................................................................................176

Configuring the Network From the Computer .......................................................177

■ Displaying and Configuring the Network Configuration Screen....................................177

■ Resetting to Factory Defaults ........................................................................................ 180

■ Setting Errors ................................................................................................................. 180

Setting Up the Network............................................................................................182

■ Setting Basic Information [Network] .............................................................................. 182

■ Setting Up Email [Mail] .................................................................................................. 183

■ Mail Authentication Settings [Mail auth] ........................................................................ 184

■ Sending a Test Mail [Send test mail]............................................................................. 185

■ SNMP Settings [SNMP] ................................................................................................. 185

■ Setting Projector Information [Projector info.]................................................................ 186

■ Setting PJLink [PJLink] .................................................................................................. 187

Table of Contents

Controlling the Projector from a Computer........................................................... 188

Error Mail .................................................................................................................. 190

Maintenance ................................................................................................... 191

Cleaning the Projector............................................................................................. 192

Cleaning and Replacing the Air Filter .................................................................... 193

Replacing the Air Filter ........................................................................................................... 193

Cleaning the Air Filter............................................................................................................. 194

Replacing the Lamp................................................................................................. 195

Replacement Lamp ................................................................................................................196

Replacing the Lamp ............................................................................................................... 196

Appendix ....................................................... 199

Appendix......................................................................................................... 201

Troubleshooting....................................................................................................... 202

LED Indicator Meanings ......................................................................................................... 202

Symptoms and Solutions........................................................................................................ 203

■ You Cannot Turn on the Projector................................................................................. 203

■ You Cannot Project an Image from the Projector ......................................................... 203

■ There is no Sound ......................................................................................................... 204

■ The Projected Image Is Blurred .................................................................................... 205

■ You Cannot Project an Image Appropriately ................................................................ 205

■ The Projector Power Turns Off ...................................................................................... 205

■ You Cannot Operate the Remote Control ..................................................................... 206

Relationship between Aspect and Screen Aspect................................................ 207

WUX5000 / WUX4000............................................................................................................ 207

■ When the image is projected on a 16:10 screen .......................................................... 207

■ When the image is projected on a 16:9 screen ............................................................ 208

■ When the image is projected on a 4:3 screen .............................................................. 208

■ When projecting on a 16:10 screen in the aspect ratio of the connected device ........ 209

■ When projecting on a 16:9 screen in the aspect ratio of the connected device .......... 209

■ When projecting on a 4:3 screen in the aspect ratio of the connected device ............ 210

WX6000.................................................................................................................................. 210

■ When the image is projected on a 16:10 screen .......................................................... 210

■ When the image is projected on a 16:9 screen ............................................................ 211

■ When the image is projected on a 4:3 screen .............................................................. 211

■ When projecting on a 16:10 screen in the aspect ratio of the connected device ........ 212

■ When projecting on a 16:9 screen in the aspect ratio of the connected device .......... 212

■ When projecting on a 4:3 screen in the aspect ratio of the connected device ............ 213

SX6000................................................................................................................................... 213

■ When the image is projected on a 4:3 screen .............................................................. 213

■ When the image is projected on a 16:10 screen .......................................................... 214

■ When the image is projected on a 16:9 screen ............................................................ 214

■ When projecting on a 4:3 screen in the aspect ratio of the connected device ............ 215

Table of Contents

■ When projecting on a 16:10 screen in the aspect ratio of the connected device......... 215

■ When projecting on a 16:9 screen in the aspect ratio of the connected device........... 216

Displayed Test Patterns...........................................................................................217

Supported Signal Types ..........................................................................................218

Product Specifications ............................................................................................219

■ Projector ........................................................................................................................ 219

■ Remote control .............................................................................................................. 221

■ Specification of Each Lens Unit (Option) ...................................................................... 221

■ External View ................................................................................................................. 223

■ ANALOG PC (WUX5000 / WUX4000), ANALOG PC-1 (WX6000 / SX6000) /

COMPONENT IN Terminal ................................................................................................ 223

■ Service Port (CONTROL)............................................................................................... 224

Index ..........................................................................................................................228

Menu Configuration ................................................................................................232

Safety Instructions

Before installing and operating the projector, read this manual thoroughly.

This projector provides many convenient features and functions. Operating the projector

properly enables you to manage those features and maintain it in good condition for

many years to come.

Improper operation may result in not only shortening the product life, but also malfunc-

tions, fire hazards, or other accidents.

If your projector does not seem to be operating properly, read this manual again, check

operations and cable connections, and try the solutions in the “Troubleshooting” section

in the back of this manual. If the problem still persists, contact the Canon Customer Sup-

port Center.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE

EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUT-

ING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING

AND MAINTENANCE INSTRUCTIONS FOR THIS UNIT IN THE OWNER’S

MANUAL.

CAUTION

Not for use in a computer room as defined in the Standard for the Protection of Elec-

tronic Computer / Data Processing Equipment, ANSI / NFPA 75.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Safety Instructions

Safety Precautions

WARNING:

• THIS APPARATUS MUST BE GROUNDED.

• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

• This projector produces intense light from the projection lens. Do not stare directly into

the lens, otherwise eye damage could result. Be especially careful that children do not

stare directly into the beam.

• Install the projector in a proper position. Otherwise it may result in a fire hazard.

• Allowing the proper amount of space on the top, sides, and rear of the projector cabinet

is critical for proper air circulation and cooling of the unit. The diagrams shown here

indicates the minimum space required. If the projector is to be built into a compartment

or similarly enclosed, these minimum distances must be maintained.

• Do not cover the ventilation slots on the projector. Heat build-up can reduce the service

life of your projector, and can also be dangerous.

• If the projector is unused for an extended time, unplug the projector from the power out-

let.

• Do not project the same image for a long time.

An afterimage may remain on the LCD panels due to the characteristics of the panels of

the projector.

CAUTION ON HANGING FROM THE CEILING

When hanging the projector from the ceiling, clean the air intake vents and top of the pro-

jector periodically with a vacuum cleaner. If you leave the projector unclean for a long

time, the cooling fans can be clogged with dust, and it may cause a breakdown or a

disaster.

DO NOT SET THE PROJECTOR IN GREASY, WET, OR SMOKY CONDITIONS SUCH

AS IN A KITCHEN TO PREVENT A BREAKDOWN OR A DISASTER. IF THE PROJEC-

TOR COMES IN CONTACT WITH OIL OR CHEMICALS, IT MAY BECOME DETERIO-

RATED.

SIDE and TOP REAR

50 cm (1.6') 50 cm (1.6')

50 cm (1.6')

Safety Instructions

■READ AND KEEP THIS OWNER’S MANUAL FOR LATER USE.

All the safety and operating instructions should be read before beginning to operate the

product.

Read all of the instructions given here and retain them for later use. Unplug this projector

from the AC power supply before cleaning. Do not use liquid or aerosol cleaners on the

projector. Use a damp cloth for cleaning.

Follow all warnings and instructions marked on the projector.

For added protection of the projector during a lightning storm, or when it is left unat-

tended or unused for long periods of time, unplug it from the wall outlet. This will prevent

damage due to lightning and power surges.

Do not expose this unit to rain or use near water... for example, in a wet basement, near a

swimming pool, etc...

Do not use attachments not recommended by the manufacturer as they may result in haz-

ards.

Do not place this projector on an unstable cart, stand, or table. The projector may fall,

causing serious injury to a child or adult, and serious damage to the projector. Use only

with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or

shelf mounting should be carried out in accordance with the manufacturer’s directions,

and should use a mounting kit approved by the manufacturers.

An appliance and cart combination should be moved with care.

Sudden stops, excessive force, and uneven surfaces may cause the

appliance and cart combination to overturn.

Slots and openings in the rear and front of the cabinet are provided for

ventilation, to insure reliable operation of the equipment and to protect

it from overheating.

The openings should never be covered with cloth or other materials, and the bottom

opening should not be blocked by placing the projector on a bed, sofa, rug, or other sim-

ilar surface. This projector should never be placed near or over a radiator or heat register.

This projector should not be placed in a built-in installation such as a book case unless

proper ventilation is provided.

Safety Instructions

Never push objects of any kind into this projector through cabinet slots as they may touch

dangerous voltage points or short out parts that could result in a fire or electric shock.

Never spill liquid of any kind onto the projector.

Do not install the projector near the ventilation duct of air-conditioning equipment.

This projector should be operated using only the type of power source indicated on the

marking label. If you are not sure of the type of power supplied, contact the Canon Cus-

tomer Support Center or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock.

Do not allow anything to rest on the power cord. Do not locate this projector where the

cord may be damaged by people walking on it.

Do not attempt to service this projector yourself as opening or removing covers may

expose you to dangerous voltages or other hazards. Refer all servicing to qualified ser-

vice personnel.

Unplug this projector from the wall outlet and refer servicing to qualified service person-

nel under the following conditions:

a. When the power cord or plug is damaged or frayed.

b. If liquid has been spilled into the projector.

c. If the projector has been exposed to rain or water.

d. If the projector does not operate normally after following the operating instructions.

Adjust only those controls that are covered in the operating instructions as improper

adjustment of other controls may result in damage and will often require extensive work

by a qualified technician to restore the projector to normal operating condition.

e. If the projector has been dropped or the cabinet has been damaged.

f. When the projector exhibits a distinct change in performance-this indicates a need for

servicing.

When replacement parts are required, be sure the service technician uses replacement

parts specified by the manufacturer that have the same characteristics as the original

parts. Unauthorized substitutions may result in fire, electric shock, or injury.

Upon completion of any service or repairs to this projector, ask the service technician to

perform routine safety checks to determine that the projector is in safe operating condi-

tion.

Safety Instructions

AC Power Cord Requirement

The AC Power Cord supplied with this projector meets the requirements for use in the

country you purchased it.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EAS-

ILY ACCESSIBLE.

AC Power Cord for the United States and Canada:

The AC Power Cord used in the United States and Canada is

listed by the Underwriters Laboratories (UL) and certified by the

Canadian Standard Association (CSA).

The AC Power Cord has a grounding-type AC line plug. This is a

safety feature to ensure the plug fits into the power outlet. Do not

try to tamper with this safety feature. Should you be unable to

insert the plug into the outlet, contact your electrician.

NOTE FOR CUSTOMERS IN THE US

LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED

OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS.

European Union (and EEA) only.

These symbols indicate that this product is not to be disposed of with

your household waste, according to the WEEE Directive (2002/96/EC),

the Battery Directive (2006/66/EC) and / or your national laws imple-

menting those Directives. If a chemical symbol is printed beneath the

symbol shown above, in accordance with the Battery Directive, this

indicates that a heavy metal (Hg = Mercury, Cd = Cadmium, Pb =

Lead) is present in this battery or accumulator at a concentration above

an applicable threshold specified in the Battery Directive. This product

should be handed over to a designated collection point, e.g., on an

authorized one-for-one basis when you buy a new similar product or to

an authorized collection site for recycling waste electrical and elec-

tronic equipment (EEE) and batteries and accumulators. Improper han-

dling of this type of waste could have a possible impact on the

environment and human health due to potentially hazardous sub-

stances that are generally associated with EEE. Your cooperation in the

correct disposal of this product will contribute to the effective usage of

natural resources. For more information about the recycling of this

product, please contact your local city office, waste authority, approved

scheme or your household waste disposal service or visit

www.canon-europe.com/environment.

(EEA: Norway, Iceland and Liechtenstein)

Ground

Safety Instructions

Federal Communication Commission Notice

Multimedia Projector, Model: WUX5000 / WUX4000 / WX6000 / SX6000

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pro-

vide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or tele-

vision reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

The cable with a ferrite core provided with the projector must be used with this equip-

ment in order to comply with Class B limits in Subpart B of Part 15 of the FCC rules.

Use of a shielded cable is required to comply with class B limits in Subpart B of Part 15

of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified

in the instructions. If such changes or modifications should be made, you could be

required to stop operation of the equipment.

Canon U.S.A. Inc.

One Canon Plaza, Lake Success, NY 11042-1198, U.S.A.

Tel No. (516) 328-5600

Canadian Radio Interference Regulations

This Class B digital apparatus complies with Canadian ICES-003.

Safety Instructions

Precautions for Use

As this section contains important safety-related information, be sure to read the following

carefully beforehand in order to use your projector correctly and safely.

If the following situations occur, turn the power off, remove the power plug from the

power outlet and contact the Canon Customer Support Center. Failure to do so could

cause a fire or result in an electric shock.

• If smoke is emitted

• If an unusual smell or noise is emitted

• If a loud noise is heard and the lamp turns off

• If water or other liquid has entered the projector

• If metal or any other foreign material has entered the projector

• If the projector is knocked over or dropped and the cabinet is damaged

Pay attention to the following points for handling the power cord. Failing to pay atten-

tion to these points could cause a fire, electric shock or personal injury.

• Do not place any objects on the power cord and do not allow it to become trapped

under the projector. The power cord may be damaged.

• Do not cover the power cord with a carpet.

• Do not excessively bend, twist, pull or make modifications to the power cord.

• Keep the power cord away from heaters and other sources of heat.

• Do not use the power cord when it is bent finely, coiled or bundled.

• Do not use a damaged power cord. If your power cord is damaged, contact the

Canon Customer Support Center.

• Do not use any power cord other than the type that is included with this projector.

• Be sure to connect the ground wire of the power cord to ground. Failure to do so

could result in an electric shock.

• Be sure to connect the ground wire before connecting the power plug to the outlet.

Also when you disconnect the ground wire, be sure to unplug the power plug from

the outlet beforehand.

Warning

Safety Instructions

Precautions for Installation

Pay attention to the following points regarding the power source, power plug and han-

dling of the connector. Failure to do so could result in a fire, electric shock or personal

injury.

• Do not use any power source with a voltage other than the voltage indicated (AC 100

– 240 V).

• Do not pull the power cord and be sure to hold the power plug or connector when

removing. The cord could be damaged as a result.

• Do not insert any metal objects into the contact parts of the power plug or connector.

• Remove the power plug from the outlet before performing cleaning or maintenance

of the projector.

• Do not remove the power plug or connector with wet hands.

• Insert the power plug and connector securely up to the base. Additionally, do not

use a damaged power plug or an outlet that is loose.

• If using an extension cord attached to the outlet, make sure that the total electric

power consumption of connected devices does not exceed the rated capacity.

• Periodically inspect the power plug and outlet and remove any dust or dirt from

between the plug and the outlet.

Pay attention to the following points regarding installation and handling of the projector.

Failure to do so may cause a fire, electric shock or personal injury.

• Do not use the projector in a bathroom or shower room.

• Do not use the projector in rain or snow, by the sea, or in close proximity to a body of

water.

• Do not place containers containing a liquid on top of the projector.

• Do not place the projector in any location where it will be exposed to oily smoke or

steam, such as a kitchen work surface or table etc.

• Do not touch the projector itself, the power cord, or the cable if lightening strikes.

Warning

Safety Instructions

Pay attention to the following points regarding installation and handling of the projector.

Failure to do so may cause a fire, electric shock or personal injury.

• Do not move the projector until you have switched off the power, removed the power

plug from the power outlet and unplugged any other cables.

• Before installing or replacing a lens unit, make sure to remove the power plug from

the outlet. Failure to do so could result in an electric shock or injury.

• Do not remove the cabinet from the projector or disassemble it. The interior of the

projector contains high-voltage components as well as parts that are hot. These

could cause an electric shock or burn. If inspection, maintenance or repair is

required, contact the Canon Customer Support Center.

• Do not disassemble or modify the projector (including consumable parts) or the

remote control.

• Do not insert any object into vents in the projector, such as the air intake vent or

exhaust vents.

• Do not place a pressurized can in front of the exhaust vents. The pressure of the

contents of the can may increase due to heat from the exhaust vents and this could

result in an explosion.

• As strong light beams are emitted while the projector is in use, do not look directly

into the projector lens. Doing so could cause an eye injury. Pay particular attention in

preventing young children to do so.

• When giving a presentation in front of the projector while it is projecting an image,

conduct your presentation from a position where your shadow will not be cast on the

screen and where you do not feel blinded by light from the projector.

Pay attention to the following points regarding installation and handling of the projec-

tor.

• If the projector will not be used for a long period of time, be sure to remove the

power plug from the power outlet to ensure safety. Failure to do so could cause a

fire.

•

The temperature of the cabinet around and above the exhaust vents can become hot

during projector operation.

Touching these areas during operation could cause

burns to the hands.

Do not touch these areas. Doing so may cause burns. Pay particular attention in pre-

venting young children from touching these parts. Additionally, do not place any

metal objects on these areas. Due to the heat from the projector, doing so could

cause an accident or personal injury.

Warning

Caution

Safety Instructions

Precautions on the lamp

Pay attention to the following points regarding installation and handling of the projector.

• Do not place any heavy objects on top of the projector or sit / stand on it. Pay partic-

ular attention to prevent small children from doing so. The projector may be knocked

over and this could result in damage or a personal injury.

• Do not place the projector on an unstable or slanted surface. Doing so may cause

the projector to fall or be knocked over and could result in a personal injury.

• Do not place any objects in front of the lens while the projector is operating. Doing so

could cause a fire.

• When cleaning off dust or dirt from the projector lens etc., do not use any kind of

spray that is flammable. As the temperature of the lamp inside the projector is high, it

could ignite, causing a fire.

• Using the lens shift function the lens in the projector moves up / down / left / right

cause a personal injury.

• Before replacing the lens unit, wait at least one hour after the projector is turned off

to allow the projector to cool thoroughly. Failure to do so could result in a burn or

injury.

• If the projector is used for a long period of time, dust could accumulate inside the

projector. This could cause a fire or malfunction. It is recommended that periodic

maintenance of the projector be performed. For details of maintenance costs, con-

tact the Canon Customer Support Center.

• When hanging the projector from a ceiling, put the projector down on the floor or a

workbench before attaching or replacing the lens unit. Failure to do so could result in

parts falling off the projector and may cause an accident or personal injury.

When replacing the lamp, or when the lamp is damaged, pay attention to the following

points. Failure to do so could result in an electric shock or personal injury.

• Be sure to remove the power plug from the power outlet before replacing the lamp.

• When the lamp is damaged, shards of glass may be scattered inside the projector.

Contact the Canon Customer Support Center for cleaning and inspection of the pro-

jector interior and lamp replacement.

Caution

Warning

Safety Instructions

Precautions for the batteries of the remote control

When handling the lamp, pay attention to the following points.

• Be sure not to handle the lamp immediately after it has been used. Be sure to switch

off the power and wait for approximately 1 hour for the lamp and the projector to cool

down sufficiently. Failure to do so could result in a burn or personal injury due to heat

from the lamp or projector.

• When an instruction to replace the lamp has been displayed (LAMP Indicator Dis-

plays (P39)), the possibility of the lamp breaking will increase. Replace the lamp with

a new one as soon as possible.

• If the lamp is damaged, gas inside the lamp (containing mercury) and dust may be

emitted from the exhaust vents. If this happens, immediately open the windows and

doors to provide ventilation to the room. If you inhale any gas emitted from the lamp

or it has come into contact with your eyes or mouth, consult a doctor immediately.

• When disposing of a used mercury lamp, dispose of it in the same way as a fluores-

cent lamp and in accordance with the local regulations where you live.

Pay attention to the following points regarding handling of batteries. Failure to do so

could result in a fire or injury.

• Do not place the batteries in a fire or apply heat to, short circuit or disassemble the

batteries.

• Do not attempt to recharge the batteries that are included with the remote control.

• Remove the batteries when they have been fully used, or if they will not be used for a

long period of time.

• When replacing the batteries, replace both at the same time. Also, do not use two

batteries of a different type at the same time.

• Insert the batteries in the correct + / - positions.

• If any liquid leaks from the batteries and comes into contact with skin, wash off thor-

oughly with water.

Caution

Warning

Safety Instructions

For Safe Use

Pay attention to the following points when carrying or transporting the projector.

• This projector is a precision instrument. Do not knock it over or subject it to impacts.

Doing so may cause a malfunction.

• When carrying or holding up the projector after attaching the lens unit, be sure not to

hold the lens. Doing so may cause damage to the lens unit.

• Do not reuse any packaging or shock-absorbent materials that were supplied with

the projector at the time of purchase for transporting or shipping the projector. Pro-

tection of the projector cannot be guaranteed if used packaging or shock-absorbent

materials are reused. Fragments from shock-absorbent material may also enter the

interior of the projector which could cause a malfunction.

• If transportation is necessary, the lens unit should be removed before transporting

the projector. If the projector is subjected to excessive impacts during transporta-

tion, the lens unit may be damaged. Removal and installation of the lens unit should

not be performed by the user. Be sure to have the procedure performed by a quali-

fied technician or contact the Canon Customer Support Center.

Safety Instructions

Pay attention to the following points when installing or using the projector.

• Be sure to install the projector in a location where the air intake and exhaust vents

are separated from the wall by more than 50 cm (1.6'). Failure to do so could cause

a malfunction.

• Do not install the projector in a location that is damp, or where there is a lot of dust,

oily smoke or tobacco smoke. Doing so could cause contamination of optical com-

ponents such as the lens and the mirror and may result in deterioration of image

quality.

• Do not touch the lens with bare hands. Doing so may result in deterioration of image

quality.

• If the projector is suddenly moved from a location where the temperature is low to a

location where the temperature is high, or if the temperature in the location where the

projector is installed increases suddenly, moisture in the air could cause condensa-

tion to form on the projector lens or mirror. This may cause a blurred image. Wait until

the condensation has evaporated for the image projected to return to normal.

• Do not install the projector in a location where the temperature is high or low. Doing

so may cause a malfunction.

Operating temperature: 5°C to 35°C Humidity level: up to 85%

Storage temperature: -10°C to 60°C

• Do not install the projector near high-voltage electrical power lines or an electrical

power source.

• Do not use the projector on a soft surface such as carpet or sponge mat, etc. Doing

so could cause heat to build up inside the projector and this could result in a mal-

function.

• Do not block the air intake or exhaust vents of the cooling fan. Doing so could cause

heat to build up inside the projector and may cause a malfunction.

• Installing the projector in the wrong direction may cause a malfunction or accident.

Install the projector so that the left / right incline is within 10°.

• Do not place any objects on top of the projector that may change shape or color due

to heat.

• When using the projector at altitudes greater than 2,300 m, or for projecting

upward / downward:

When using the projector at altitudes greater than 2,300 m, or for upward pro-

jection or downward projection, it is necessary to change the settings of the

projector. For further details, contact the Canon Customer Support Center.

For Safe Use

Installation

Connecting to a Network

Maintenance

Appendix

Index

AppendixInstallation Manual

Projecting an Image

Safety Instructions

Before Use

Table of Contents

Setting Functions from Menus

User’s Manual

Useful Functions Available

During a Presentation

Before Use

Supplied Accessories

Check that the following accessories have been supplied with the projector.

Remote control

Batteries for the remote control

Power cord (1.8 m)

For the U.S.A. and

Canada

User’s Manual /

Installation Manual (CD-ROM)

Warranty Card

Important Information

VGA cable (1.8 m) for connection

to a computer (part No.: YH7-2307)

(mini D-sub 15-pin / mini D-sub 15-pin)

For Continental Eu-

rope

(AAA size x2) (AA size x2)

(part No.: RS-RC04) (part No.: RS-RC05)

Supplied Accessories

Before Use

■Installing Remote Control Batteries

• If buttons on the remote control are inoperative when you attempt to operate the projector,

replace the batteries with new ones.

• Do not drop the remote control or subject it to impact.

• Do not spill any liquids on the remote controller. Doing so could damage it.

1Open the battery com-

partment lid.

Raise the battery

cover tab while push-

ing it.

3Close the compart-

ment lid.

Insert the tab into the

remote control notch

(1) and push the bat-

tery cover down (2).

2Insert batteries.

Insert 2 new AA batter-

ies in the compart-

ment with the + and –

poles positioned cor-

rectly.

1Open the battery com-

partment lid.

Slide the lid while

pressing it down.

2Insert batteries.

Insert 2 new AAA bat-

teries in the compart-

ment with the + and –

poles positioned cor-

rectly.

3Close the compart-

ment lid.

Slide the lid until you

hear a click to

securely close it.

(1) (2)

Supplied Accessories

Pay attention to the following points when handling the bat-

teries. Failing to do so could result in a fire or personal

injury.

• Do not heat, short circuit or disassemble the batteries, or

place them in a fire.

• Do not attempt to recharge the batteries that are included

with the remote control.

• Remove the batteries when they are flat or when the

remote control will not be used for a long period of time.

• When replacing the batteries, replace both batteries at the

same time and do not use two batteries of a different type

together.

• Insert the batteries with the + and - terminals in the correct

directions.

• If any liquid from inside the batteries leaks out and con-

tacts your skin, be sure to wash the liquid off thoroughly.

Before Use

Preparing the Remote Control

■Remote Control Operating Range

The remote control is an infrared type. Point it at the infrared remote receiver on the front

or rear of the projector to operate it.

• Use the remote control within a distance of approximately 8 m (26.3') from the projector.

• Use the remote control within an angle of 25° in any direction from directly in front of the

infrared remote receiver.

• The remote control may be inoperative if there is an obstacle between the remote control

and main unit or the infrared remote receiver on the main unit is exposed to direct sunlight

or strong light of lighting equipment.

• When you use 2 or more projectors at the same time, you can change the channel set-

tings to prevent the 2 remote controls from interfering with each other. (P124)

(26.3')

Preparing the Remote Control

■When a remote control is connected using a cable (WX6000 / SX6000)

The remote control for WX6000 / SX6000 (RS-RC05) can be used connected to the pro-

jector with a cable.

Use a cable with a Ø3.5 mm stereo mini jack (not included).

• Infrared operations cannot be performed if a cable is connected to the projector or the

remote control.

• Use a cable with a Ø3.5 mm stereo mini jack (not included) with a length of 30 m or less.

Ø3.5 mm stereo mini jack cable

(not included)

Terminal for

wired remote

control

Before Use

Part Names

Main Unit (The illustration shows WUX5000.)

■Front Side

Terminals

and con-

nectors

Infrared remote receiver (P29)

Lens unit

Air intake vent

Power cord connector (P56)

Side control (P38)

Air filter (P193)

Anti-theft lock hole

An anti-theft wire cable (not included) can be

connected.

Do not block the air intake.

Doing so may cause a malfunc-

tion.

Part Names

■Rear Side

■Bottom Side

Exhaust vent

Infrared remote receiver (P29)

Do not block the air exhaust.

Doing so may cause a malfunc-

tion.

Lamp cover

Adjustable feet (P150)

Screw holes for installation of ceiling

attachment

Part Names

Before Use

Mounting the Projector on the Ceiling

You can mount the projector on the ceiling.

The ceiling attachment (part No.: RS-CL11)

is required in order to mount the projector on

the ceiling. Depending on the installation

environment, an extension pipe (part No.:

RS-CL08 or RS-CL09) may also be required.

Contact the Canon Customer Support Center

for more detailed information.

If you mount the projector on the ceil-

ing, you have to invert the projected

image by selecting [Image flip H/V]

from the menu. (P104)

• Make sure to use the optional ceil-

ing attachment.

• You should never install the ceiling

attachment by yourself.

Part Names

Remote Control

The projector can be operated using buttons on the remote control or the side control on

the main unit. The RS-RC04 remote control is included with WUX5000 / WUX4000 and the

RS-RC05 remote control is included with WX6000 / SX6000.

The remote control allows you to operate all functions of the projector.

■RS-RC04

POWER button (P56, P80)

Turns the projector on or off.

FOCUS button (P73)

Adjusts focusing.

[ ] / [ ] buttons: Moves the focus posi-

tion farther away.

[ ] / [ ] buttons: Moves the focus posi-

tion nearer.

ASPECT button (P70)

Changes the aspect ratio mode.

D.SHIFT/KEYSTONE button (P76)

Corrects keystone distortion.

[ ], [ ], [ ] / [ ] buttons: For keystone

adjustment.

Press D.SHIFT/KEYSTONE to correct

keystone distortion.

• Moves the image up, down, left, or right

when the screen aspect setting is [16:9

D. image shift] or [4:3 D. image shift] is

selected. (P67, P68)

• To move the image, use the [ ] / [ ] or

the [ ] / [ ] buttons.

D. ZOOM button (P84)

Zooms the image in or out digitally.

[+] button: Zooms the image in (up to 12x).

[+] button: Zooms the image out (1x mini-

mum).

[], [], [] / []

buttons: Move the zoom-

in location.

FREEZE button (P82)

Freezes the projected image.

IMAGE button (P79)

Switches the image mode (image quality).

–

Part Names

Before Use

LENS-SHIFT button (P74)

Moves the lens up, down, left, or right.

[], [], [] / [] buttons: Move the lens.

INPUT button (P60)

Switches the input signal.

ZOOM button (P71)

Adjusts the image size.

[ ] / [ ] buttons: Increase the image size.

[ ] / [ ] buttons: Decrease the image size.

Pointer buttons (P90)

Selects the upper, lower, left or right item in the menu

and performs remote control channel settings. (P127)

MENU button (P88)

Displays the menu on the screen and performs remote control

channel settings.

VOL button (P83)

Adjusts the sound volume.

[+] button: Increases the volume.

[+] button: Decreases the volume.

BLANK button (P82)

Toggles between display / non-display of image.

P-TIMER button (P85)

Displays the time elapsed since this

button was pressed.

AUTO PC button (P62)

Adjusts tracking etc. automatically in accordance with the signal from

a computer when the analog PC input is selected.

OK button (P92)

Confirms the item selected from the menu.

MUTE button (P83)

Mutes the sound.

LAMP button (WUX4000) (P119)

Toggles the lamp mode between Standard

and Silent.

GAMMA button (P113)

Adjusts the gamma of the image.

[ ] button: Corrects dark parts of the image so that they are easier to see.

[ ] button: Corrects bright parts of the image so that they are easier to see.

–

Part Names

■RS-RC05

POWER button (P56, P80)

Turns the projector on or off.

IMAGE button (P79)

Switches the image mode (image quality).

Pointer buttons (P90)

Selects the upper, lower, left or right item

in the menu. Performs remote control

channel settings when the remote control

is used via the infrared transmitter. (P124)

OK button (P92)

Determines the item selected from the menu.

ZOOM button (P71)

Adjusts the image size.

[ ] / [ ] buttons: Increase the image size.

[ ] / [ ] buttons: Decrease the image size.

FOCUS button (P73)

Adjusts focusing.

[ ] / [ ] buttons: Moves the focus position further away.

[ ] / [ ] buttons: Moves the focus position nearer.

ASPECT button (P70)

Changes the aspect ratio mode.

Ch button (P124)

Changes the remote control channel when

the remote control is used via the infrared

transmitter.

D.ZOOM button (P84)

Zooms the image in or out digitally.

[1] button: Zooms the image in (up to 12x).

[4] button: Zooms the image out (1x minimum).

[ ] / [ ] / [ ] / [ ] buttons: Move the zoom-in

location.

TEST PATTERN button (P138, P217)

Displays the test pattern.

Part Names

Before Use

SHIFT button (P74)

Moves the lens up, down, left or right.

[] / [] / [] / []

buttons:

Move the lens.

INPUT button (P60)

Switches the input signal.

MENU button (P89)

Displays the menu on the screen. Performs remote control channel settings

when the remote control is used via the infrared transmitter. (P127

)

VOL button (P83)

Adjusts the sound volume.

[3] button: Increases the volume.

[6] button: Decreases the volume.

BLANK button (P82)

Toggles between display / non-display of

the image.

AUTO PC button (P62)

Adjusts tracking etc. automatically in accordance with the signal from a com-

puter when the analog PC input is selected.

EXIT button (P92)

Cancels functions such as menu

display or test pattern during oper-

ation and returns to the image dis-

play.

MUTE button (P83)

Mutes the sound.

Change input buttons (P60)

Change the input signal between Digital

PC, Analog PC-1, Analog PC-2, HDMI

and Component.

KEYSTONE button (P76)

Corrects keystone distortion.

To move the image, use the [ ] / [ ] or [ ] / [ ] buttons.

Fn button

Cannot be used on this

product.

FREEZE button (P82)

Freezes the projected image.

Numerical buttons (P129, P173, P175)

Enter password and TCP/IP setting values.

Terminal for wired remote control (P30)

Connects a cable to the projector for remote control operation.

Part Names

Side Control

(1) LED indicators (P39)

The projector status is shown by the LED indicators (off / on / flashing).

For indicator status, refer to page 39.

(2) POWER button (P56, P80)

Turns the projector on or off.

(3) MENU button (P88, P89)

Displays a menu on the screen.

(4) LENS button

Each time the button is pressed, the

screen changes to focus adjustment

(P73), zoom (image size) adjustment

(P71), or lens shift (image position)

adjustment (P74). To adjust, use the

[] / [] or the [] / [] buttons.

(5) INPUT button (P60)

Switches the input signal.

(6) Pointer / VOL buttons (P90)

Adjust the sound volume.

[ ] button: Decreases the volume.

[ ] button: Increases the volume.

Selects the upper, lower, left or right

item in the menu.

(7) OK button (P92)

Determines the item selected from the

menu.

• POWER ON (green): Lights up or flashes when the power is on.

• STAND BY (red) : Lights up or flashes during standby or when the projector is

shut down.

• WARNING (red) : Lights up or flashes when an error occurs.

• LAMP (orange) : Flashes when the time for replacing the lamp is near. When a

lamp cover error occurs, the [WARNING] indicator will also

flash. When a lamp error occurs, it will illuminate at the same

time as the [WARNING] indicator.

• TEMP (red) : When the temperature inside the projector is high, it will flash. If

the temperature inside the projector increases further and a

temperature error occurs, it will illuminate at the same time that

the [WARNING] indicator illuminates.

(1)

(2)

(3)

(4)

(5)

(7) (6)

Part Names

Before Use

■LED Indicator Displays

The LED indicators flash or illuminate to indicate the operating status of the projector.

* Either the [POWER ON] or [STAND BY] indicator illuminates, depending on the power

status.

: Off : Lit : Flashing

LED indicator

Operating status

POWER

(green)

STAND BY

(red)

WARN-

ING (red)

LAMP

(orange)

TEMP

(red)

Power is not connected.

Ready to turn power on (standby).

Power is on.

Power-saving mode engaged.

* *The time for replacing the lamp is near.

Internal temperature is high.

A lamp error has occurred.

Power was turned off due to high inter-

nal temperature.

The lamp cover is open.

Another error has occurred.

Part Names

Input Terminal

(1)LAN port (P166)

Connects the LAN cable.

Used to connect the projector to a network.

(2)ANALOG PC / COMPONENT IN terminal

( /COMPONENT IN) (P47, P53)

Receives the analog PC signal (Analog PC).

A component cable can be used to receive the component image signal (Component).

(3)DVI-D IN terminal ( DVI-D IN) (P50)

Connects the external monitor output from a computer.

Receives the digital signal (Digital PC).

(4)HDMI IN terminal (HDMI IN) (P51)

Receives the digital content image signal (HDMI).

Carries both video and audio signals across a single cable.

(5)Service port (CONTROL)

This terminal is used by servicing technicians. It is not used during ordinary use.

(6)AUDIO IN terminal (AUDIO IN) (P47, P50, P53)

Receives the audio input corresponding to 2 image input systems other than HDMI IN.

The internal speaker outputs the audio for the selected image signal.

(7)AUDIO OUT terminal ( AUDIO OUT) (P51, P55)

Outputs the audio to external AV equipment. This outputs the audio signal that corre-

sponds to the projected image signal.

(1) (2) (3) (4) (5) (6) (7)

Part Names

Before Use

(1)LAN port (P166)

Connects the LAN cable.

Used to connect the projector to a network.

(2)ANALOG PC-1 / COMPONENT IN terminal

( /COMPONENT IN) (P47, P53)

Receives the analog PC signal (Analog PC-1).

A component cable can be used to receive the component image signal (Component).

(3)ANALOG PC- 2 / DVI-I IN terminal ( DVI-I IN) (P50)

Connects the external monitor output from a computer.

Receives the digital PC signal (Digital PC) or analog PC signal (Analog PC-2).

(4)HDMI IN terminal (HDMI IN) (P51)

Receives the

digital content image signal (HDMI).

Carries both video and audio signals across a single cable.

(5)Service port (CONTROL)

This terminal is used by servicing technicians. It is not used during ordinary use.

(6)Terminal for wired remote control (REMOTE) (P30)

This terminal is used to connect the remote control using a cable.

(7)AUDIO IN terminal (AUDIO IN) (P47, P50, P53)

Receives the audio signal input for 2 kinds of image input except HDMI IN.

The internal speaker outputs the audio for the selected image signal.

(8)AUDIO OUT terminal ( AUDIO OUT) (P51, P55)

Outputs the audio to external AV equipment. This outputs the audio signal that corre-

sponds to the projected image signal.

(1) (2) (3) (4) (5) (6) (7) (8)

MULTIMEDIA PROJECTOR

User’s Manual

(Operation)

Safety Instructions

Before Use

Table of Contents

Projecting an Image

Useful Functions Available

During a Presentation

Setting Functions from Menus

User’s Manual

Installation

Connecting to a Network

Maintenance

Appendix

Index

AppendixInstallation Manual

Projecting an

Image

Steps for Connecting the Projector and Projecting an Image

Connecting the Projector to Equipment (P162)

Starting Projection (P56)

Selecting an Input Signal (P59)

Adjusting the Image

(

P61

)

Make the following adjustments.

• Setting the Display Resolution of the Computer

(

P61

)

• Selecting an Aspect Ratio of Projected Image (Screen aspect) and a Screen

Mode (Aspect)

(

P63

P69

)

•

Adjusting Misaligned Images or Flickering of the Screen Using the Auto PC (

P62

)

• Adjusting the Image Size

(

P71

)

• Adjusting the Focus

(

P73

)

• Adjusting the Image Position (Lens shift) (P74)

• Adjusting Keystone Distortion

(

P76

)

Making Fine Adjustments

• Selecting an Image Mode

(

P78

)

Do you want to project an image from a

notebook computer?

Is the image projected properly?

For a notebook computer,

turn on the monitor output

(P58) and then proceed.

Yes

Projection is complete.

Yes

Installation work should be performed by a qualified technician.

Contact the Canon Customer Support Center for further information.

User’s Manual Projectin

an Ima

Connecting the Projector

Connecting the Projector to a Computer

Connect the projector to the computer.

A digital connection (P50) is recommended when projecting an image in high quality.

When using a computer with an HDMI output terminal, a digital connection (P51) can be

made using an HDMI cable.

■Connecting to RGB Monitor Output Terminal (Analog Connection)

Connecting with a VGA cable (Input signal type: [Analog PC] (WUX5000 / WUX4000),

[Analog PC-1] (WX6000 / SX6000) P59)

Before connecting the cables, turn off both the projector and computer.

Computer

Monitor output

terminal

(mini D-sub 15-pin)

AUDIO output terminal

(AUDIO OUT)

VGA cable (supplied)

When inputting corresponding audio

Audio cable (not included)

To ANALOG PC /

COMPONENT IN terminal

To AUDIO IN terminal

Projector

Connecting the Projector

Connecting with VGA-DVI cable (Input signal type: [Analog PC-2] P59)

• Use a VGA cable in which all pins are connected. If the cable is a type in which all pins

are not connected, the image may not be correctly displayed.

• Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor

will reduce the audio volume.

• The AUDIO IN terminal can be changed in the Audio in terminal select screen (P139).

(WX6000 / SX6000)

Computer

Monitor output

terminal

(mini D-sub 15-pin)

AUDIO output terminal

(AUDIO OUT)

VGA cable (supplied)

When inputting corresponding audio

Audio cable (not included)

To ANALOG PC-1 /

COMPONENT IN terminal

To AUDIO IN terminal

Projector

Computer

Monitor output

terminal

(mini D-sub 15-pin)

AUDIO output terminal

(AUDIO OUT)

VGA-DVI-I cable (not included)

When inputting corresponding audio

Audio cable (not included)

To ANALOG PC-2 /

DVI-I IN terminal

To AUDIO IN terminal

Projector

Connecting the Projector

User’s Manual Projectin

an Ima

Connecting with a BNC cable (Input signal type: [Analog PC] (WUX5000 / WUX4000),

[Analog PC-1] (WX6000 / SX6000) P59)

• A signal with a dot clock higher than 162 MHz cannot be projected.

• Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor

will reduce the audio volume.

• The AUDIO IN terminal can be changed in the Audio in terminal select screen (P139).

(WX6000 / SX6000)

Computer

Monitor output

terminal

(mini D-sub 15-pin)

AUDIO output terminal

(AUDIO OUT)

BNC cable (not included)

When inputting corresponding audio

Audio cable (not included)

To ANALOG PC /

COMPONENT IN terminal

To AUDIO IN terminal

Projector

Mini D-sub 15-pin -

BNC terminal con-

verter cable (not

included)

Mini D-sub 15-pin -

BNC terminal con-

verter cable (not

included)

Computer

Monitor output

terminal

(mini D-sub 15-pin)

AUDIO output terminal

(AUDIO OUT)

BNC cable (not included)

When inputting corresponding audio

Audio cable (not included)

To ANALOG PC-1 /

COMPONENT IN terminal

To AUDIO IN terminal

Projector

Mini D-sub 15-pin -

BNC terminal con-

verter cable (not

included)

Mini D-sub 15-pin -

BNC terminal con-

verter cable (not

included)

Connecting the Projector

■Connecting to DVI Monitor Output Terminal (Digital Connection)

Connecting with a DVI cable (Input signal type: [DVI-D] (Digital PC) – P59)

• Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor

will reduce the audio volume.

• The AUDIO IN terminal can be changed in the Audio in terminal select screen (P139).

(WX6000 / SX6000)

Computer

Monitor output

terminal

(DVI terminal)

AUDIO output terminal

(AUDIO OUT)

DVI-D cable (not included)

When inputting corresponding sound

Audio cable (not included)

To DVI-D IN terminal

To AUDIO IN terminal

Projector

Computer

Monitor output

terminal

(DVI terminal)

AUDIO output terminal

(AUDIO OUT)

DVI-I cable (not included)

When inputting corresponding audio

Audio cable (not included)

To Analog PC-2 / DVI-I IN

terminal

To AUDIO IN terminal

Projector

Connecting the Projector

User’s Manual Projectin

an Ima

■Connecting with a HDMI Cable (Input signal type: [HDMI] – P59)

■Outputting Audio to Speakers

It is possible to output audio from the projected images to amplified speakers.

Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor will

reduce the audio volume.

Computer

Digital image

output terminal

(HDMI terminal)

HDMI cable (not included)

* When an HDMI cable is connected, digi-

tal audio is also connected at the same

time.

To HDMI IN terminal

Projector

Speaker

Audio input terminal

(AUDIO IN)

Audio cable (not included)

To AUDIO OUT terminal

Projector

RCA terminal

Mini jack

Connecting the Projector

Connecting to AV Equipment

Connect the projector and AV equipment.

The description provided here is one example. For more detailed information, refer to the

manual for the connected AV equipment.

■Connecting to Digital Video Output Terminal (Digital Connection)

Connecting with a HDMI cable (Input signal type: [HDMI] – P59)

Before connecting the cables, turn off both the projector and AV equipment.

AV equipment

Digital video out-

put terminal

(HDMI terminal)

HDMI cable (not included)

* When an HDMI cable is connected, digi-

tal audio is also connected at the same

time.

To HDMI IN terminal

Projector

Digital video

camera

Connecting the Projector

User’s Manual Projectin

an Ima

■Connecting to Analog Video Output Terminal (Analog Connection)

Connecting with a component cable (Input signal type: [Component] – P59)

A component video signal from the AV equipment can be inputted into the projector by

connecting the component cable to the COMPONENT IN terminal of the projector.

Use a commercially available component cable (not included) that fits the terminal type of

the AV equipment to create a relay connection.

AV equipment

To ANALOG PC / COMPONENT

IN terminal

Projector

RCA component

terminal

D terminal

RCA plug - RCA plug component cable

(not included)

D terminal plug - RCA plug component

conversion cable (not included)

Component cable

(not included)

To AUDIO IN terminal

Video output ter-

minal

DVI-D cable (not included)

Monitor output

terminal (DVI ter-

minal)

When inputting corresponding audio

Mini jack

AUDIO output terminal

Audio cable (not included)

RCA terminal

Connecting the Projector

• Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor

will reduce the audio volume.

• The AUDIO IN terminal can be changed in the Audio in terminal select screen (P139).

(WX6000 / SX6000)

AV equipment

When inputting corresponding audio

To ANALOG PC-1 / COMPO-

NENT IN terminal

Projector

RCA component

terminal

D terminal

Mini jack

AUDIO output terminal

RCA plug - RCA plug component cable

(not included)

Audio cable (not included)

D terminal plug - RCA plug component

conversion cable (not included)

Component cable

(not included)

To AUDIO IN terminal

Video output

terminal

RCA terminal

Connecting the Projector

User’s Manual Projectin

an Ima

■Outputting Audio to Speakers

It is possible to output audio from the projected images to AV equipment or amplified

speakers.

Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor will

reduce the audio volume.

RCA terminal

Speaker

Projector

To AUDIO OUT terminal

Audio cable (not included) Mini jack

Audio input terminal

(AUDIO IN)

Starting Projection

1Check the connection between the projector and the computer or AV equipment.

(P52 – P55)

2Connect the power cord and make sure that the [STAND BY] indicator is lit (red).

3Press the POWER button.

The [POWER] indicator flashes green, and then stops flashing and remains lit.

The countdown window is displayed for approximately 20 seconds, and then the pro-

jection is started. Press the OK or EXIT button (WX6000 / SX6000) to make the count-

down window disappear.

•Fully insert the power cord plug into the socket.

•After turning off the projector, wait at least 5 minutes before turning it on again.

It may shorten the lamp life if you turn on the projector immediately after turning

it off.

•Unplug the power cord when not in use.

Connect the ground terminal on the power plug to ground. Not

doing so could result in an electric shock. Also the computer

may suffer electromagnetic interference or be subject to poor TV

and radio reception.

Remote control Projector Remote control

Starting Projection

User’s Manual Projectin

an Ima

4Turn on the computer or AV equipment power.

■When the Language Selection Screen Appears

A window appears when the projector is turned on for the first time. You can select a lan-

guage to be used by the projector for displaying menus and messages in the window.

Select the desired language with the pointer buttons and press the OK button.

You can change the language from the menu at a later time. (P125)

If the language selection screen is out of focus, press the FOCUS button to perform focus

adjustment. (P73)

Changing Operations When Projector is Turned On

You can change operations when the projector is turned on as follows.

• You can turn on the projector by connecting the power cord, without pressing the

POWER button. (P121)

• You can change the countdown window. (P106)

• You can skip the countdown window. (P56)

Using the Power Saving Mode (Power Management)

When you enable the power management mode, the lamp is automatically turned

off if the projector receives no signal input for a certain period of time. (P120)

An item highlighted in orange will be selected.

Remote control Projector Remote control

Starting Projection

■When the Password Input Screen Appears

If you have set a password, the Password input screen appears. Enter your password.

(P128)

■When “No signal” Appears

With a notebook computer, the user must turn on the external monitor output. (P58)

Press the INPUT button to select the input signal. (P60)

■When Notebook Computer Screen Does Not Appear

Set your notebook computer to output signals to an external monitor. For more details,

refer to “Changing Notebook Computer Screen Output” below.

■Adjusting Image

• Set the display resolution of the computer to the highest resolution or the resolution

closest to that setting. (P61)

• Use the auto PC function to adjust shift in computer image or the flickering of the

screen. (P62)

•Use the ZOOM button to adjust the size of the projected image. (P71)

•Use the FOCUS button to correct the focus adjustment if necessary. (P73)

• Use the

D.SHIFT/KEYSTONE

button (WUX5000 / WUX4000) or

KEYSTONE

button

(WX6000 / SX6000) to adjust keystone correction if necessary. (P76)

• Select the aspect ratio of the projected image (screen aspect) or a screen mode

(aspect) according to the aspect ratio of the screen, type of input image signal etc.

(P63 - P70)

• Select an image mode depending on the projected image. (P78)

Changing Notebook Computer Screen Output

With a notebook computer, the user must turn on the external monitor output on the com-

puter side.

This operation is not required for a desktop computer.

■Turning on External Monitor Output

You can turn on the external monitor output via keyboard operation.

To turn on the external monitor output with most computers, press the function key ([F1] to

[F12]) which is marked with the external monitor icon while holding down the [Fn] key.

• The function key you use and the method used to turn on the external monitor output vary

depending on the model. For details, see the manual for your notebook computer.

• With Windows 7, you can turn on image output by holding down the Windows logo key

and pressing the [P] key.

While pushing key Press a key such as or .

User’s Manual Projectin

an Ima

Selecting an Input Signal (INPUT)

Select the input signal in the [Input] menu when you want to project a digital PC or AV

equipment signal, or to switch between inputs when multiple computers or multiple sets

of AV equipment are connected.

Skip this step if you have not changed the input signal since the last projection.

■Types of Input Signals

The table below shows the relationship among input signals supported by the projector,

input terminals and connection cables.

Input

signal

Supported

projectors Input terminal Types of connection cables

HDMI

WUX5000

WUX4000

WX6000

SX6000

HDMI cable (not included)

Digital

WUX5000

WUX4000

DVI cable (not included)

WX6000

SX6000



Analog

PC-1

WUX5000

WUX4000

WX6000

SX6000

COMPONENT IN

VGA cable (supplied)

WUX5000

WUX4000

WX6000

SX6000

COMPONENT IN

BNC cable (not included)

Analog

PC-2

WX6000

SX6000

VGA-DVI cable (not included)

Compo-

nent

WUX5000

WUX4000

WX6000

SX6000

COMPONENT IN

Component cable (not included)

BNC cable

(not included)

Mini D-sub 15-pin - BNC

terminal converter cable

(not included)

D terminal plug - RCA plug

component conversion ca-

ble (not included)

RCA plug - RCA plug com-

ponent cable (not included)

Selecting an Input Signal (INPUT)

■Selecting an Input Signal

1Press the INPUT button to display the window shown below.

The currently active input signal is marked with a circle and highlighted in orange.

An input signal that is ready for projection is displayed in white. When no signal is

received, it is displayed in gray. However [HDMI] and [DVI-D] (WUX5000 / WUX4000)

(Digital PC), or [Digital PC] (WX6000 / SX6000) may be displayed in gray even if they

are ready for projection.

2You can switch the available input signal types by pressing the INPUT button.

• You can select the target input signal with [ ] / [ ].

• Only the input signals displayed in white can be selected.

3Press the OK button to confirm the input signal type.

Change the input signal with the input signal buttons. (WX6000 / SX6000)

For WX6000 / SX6000, you can also switch to the input signal you want by pressing

the button that corresponds to that signal.

Remote control Projector Remote control

Remote control

User’s Manual Projectin

an Ima

Adjusting the Image

Setting the Display Resolution of the Computer

Based on the maximum resolution of the projector, set the display resolution of the com-

puter to the resolution closest to the output signal resolution of the projector. (P218)

Maximum resolution

WUX5000 / WUX4000: 1920 X 1200 dots

SX6000: 1400 X 1050 dots

WX6000: 1440 X 900 dots

■Windows 7

1Open the [Control Panel] from the start

menu, then select [Appearance and Per-

sonalization] - [Adjust screen resolution] in

the [Control Panel Home].

2Click the [Resolution] tab, and move the

slider to select or the resolution closest to

the maximum output signal resolution of

the computer.

Click the OK button.

■Windows Vista

1Open the [Control Panel] from the start

menu, then select [Appearance and

Personalization] - [Adjust screen reso-

lution] in the [Control Panel Home].

2Select the resolution closest to the

maximum output signal resolution of

the computer from the [Resolution] list.

3Click the OK button.

■Windows XP

1Right-click on the desktop background

and select [Properties] to open the

[Display Properties].

2Click the [Settings] tab, and under

[Screen Resolution], select the resolu-

tion closest to the maximum output

signal resolution of the computer.

3Click the OK button.

Adjusting the Image

■Mac OS X

1Open the Apple Menu and select [System

Preferences].

2In the [System Preferences] window, click

the [Displays] icon to display the Display

window.

3Select the [Display] tab and select the res-

olution closest to the maximum output sig-

nal resolution of the computer from the

[Resolutions] list.

4Close the [System Preferences] window.

AUTO PC

If the image display is shifted or there is flickering of the screen when [Analog PC]

(WUX5000 / WUX4000) or [Analog PC-1] [Analog PC-2] (WX6000 / SX6000) is selected,

press the AUTO PC button to adjust the projector to the optimal condition.

The adjustment results will be stored. If the projector is used again with the same com-

puter, when the input signal is selected the image will be projected automatically under

the same conditions that were previously adjusted.

■Performing the Auto PC Function

Press the AUTO PC button to perform projector adjustment.

If the projected image was not properly adjusted with the [AUTO PC] function, perform the

following steps.

• From [Input signal select], select an input signal type based on the resolution of the com-

puter. (P94)

• If the adjustment is still insufficient, from [Input signal settings] select [Total dots], [Track-

ing], [Horizontal position], [Vertical position], [Horizontal pixels] and [Vertical pixels] to

make adjustments. (P95 - P98)

• For the signal types supported by the projector, see the table on page 218.

Remote control

Adjusting the Image

User’s Manual Projectin

an Ima

Selecting Screen Aspect and Aspect

Select an optimum aspect ratio of the projected image (screen aspect) or an optimum

screen mode (aspect) according to the aspect ratio of the screen, type of input image

signal and so on for the projection to make best use of the screen size.

[Screen aspect] Select the same screen aspect ratio as the screen you are using.

[Aspect] In general, select [Auto].

You may need to change the setting depending on the resolution of the computer or other

AV equipment connected. If the image is not projected with the desired aspect ratio, refer

to page 207.

■Selecting Screen Aspect

Select the correct aspect ratio for the screen which is used.

Perform the following steps to select the aspect ratio of the projected image.

1Press the MENU button to display a menu window.

Remote control Projector Remote control

Adjusting the Image

2Use the [ ] / [ ] buttons to select the [Display settings] tab (WUX5000 / WUX4000) or

[Install settings] (WX6000 / SX6000).

3Select [Screen aspect] with the [] / [ ], and then press the OK button.

Remote control Projector Remote control

Adjusting the Image

User’s Manual Projectin

an Ima

4Use the [] / [ ] buttons to select the desired contents.

Screen aspect compatibility for each model of projector is as follows.

: Compatible : Not compatible

WUX5000 WUX4000 WX6000 SX6000

16:10

16:9

4:3

16:10 D. image shift

16:9 D. image shift

4:3 D. image shift

Remote control Projector Remote control

Adjusting the Image

16:10

Select this when you use a screen with aspect ratio of

16:10. Also, select this when you project an image on

a wall. You can correct keystone distortion with this

mode. (P76)

16:9

Select this when you use a screen with aspect ratio of

16:9. You can correct keystone distortion with this

mode. (P76)

4:3

Select this when you use a screen with aspect ratio of

4:3. You can correct keystone distortion with this

mode. (P76)

16:10 D. image shift (SX6000)

Select when the screen aspect ratio is 16:10. Key-

stone correction cannot be performed in this mode.

However when projecting level, it is possible to shift

the image up or down.

For details about how to shift the image, refer to page

67.

16:9 D. image shift

Select this when you use a screen with aspect ratio of 16:9. You cannot correct keystone

distortion in this mode, but you can move the image up or down with images being pro-

jected horizontally.

For the details on how to move the image, refer to page 67.

4:3 D. image shift (WUX5000 / WUX4000 / WX6000)

Select this when you use a screen with aspect ratio of 4:3.

You cannot perform the keystone adjustment in this mode; however, you can move the

image to the left or right while projecting the image horizontally.

For the details on how to move the image, refer to page 68.

5Press the OK button to confirm your setting and then press the MENU button.

16:10 screen

16:9 screen

4:3 screen

Adjusting the Image

User’s Manual Projectin

an Ima

Moving Image with 16:9 D. Image Shift / 16:10 D. Image Shift (SX6000)

16:10 D. image shift cannot be used for the WUX5000, WUX4000 and WX6000.

1For the WUX5000 / WUX4000, when the screen aspect is [16:9 D. image shift], if the

D.SHIFT/KEYSTONE button is pressed, the screen below on the right is displayed.

For the WX6000 / SX6000, when the screen aspect is [16:9 D. image shift], and for

the SX6000, when the screen aspect is set to [16:10 D. image shift], press the MENU

button, select the [Installation settings] tab with the [ ] and [ ] buttons, and then

select [Digital image shift] with the [ ] and [ ] buttons. (P108)

2Use the [ ] / [] buttons to move the image.

3When the image fits the screen, press the OK button.

Remote control

[ ] button

Moves image up

[ ] button

Moves image down

Remote control Projector

Screen

Remote control

Adjusting the Image

Moving Image with 4:3 D. Image Shift (WUX5000 / WUX4000 / WX6000)

4:3 D image shift cannot be used for SX6000.

1For the WUX5000 / WUX4000, when the screen aspect is [4:3 D. image shift], if the

D.SHIFT/KEYSTONE button is pressed, the screen below on the right is displayed.

For the WX6000, when the screen aspect is set to [4:3 D. image shift], press the

MENU button, select the [Installation settings] tab with the [ ] and [ ] buttons, and

then select [Digital image shift] with the [ ] and [ ] buttons. (P108)

2Use [ ] / [ ] to move the image.

3When the image fits the screen, press the OK button.

Remote control

[ ] button

Moves the image left

[ ] button

Moves the image right

Remote control Projector

Screen

Remote control

Adjusting the Image

User’s Manual Projectin

an Ima

Resetting the Image Shift

Perform the following steps to reset the image shift adjustment.

Press the D.SHIFT/KEYSTONE button (WUX5000 / WUX4000), twice to display the [D.

image shift reset] window.

Then, select [OK] with the [] button and press the OK button.

■Selecting Aspect Ratio

Select [Aspect] based on the input signal type, aspect ratio of the screen and resolution.

For more details about aspect ratios, refer to page 207.

Types of Aspect Ratios

Auto

The image is projected at the aspect ratio of the input signal. Select this mode for nor-

mal image projection.

Full (WUX5000 / WUX4000)

The image is projected using an input signal aspect ratio of 16:10.

Select this to project computer screen images having an aspect ratio of 16:10

(WUXGA, WSXGA+, WXGA+ and WXGA (1280 x 800)) fully on the screen.

16:10 (WX6000 / SX6000)

The image is projected using an input signal aspect ratio of 16:10.

Select this if an image of 16:10 aspect ratio cannot be correctly projected in [Auto]

mode when using video software.

16:9

The image is projected using an input signal aspect ratio of 16:9. Select this if an image

of 16:9 aspect ratio cannot be correctly projected in [Auto] mode.

4:3

The image is projected using an input signal aspect ratio of 4:3. Select this if an image

of 4:3 aspect ratio cannot be correctly projected in [Auto] mode.

Zoom

This cuts the upper/lower or left/right part of the image according to the screen aspect

and zooms in or out of the center of the image. Select this if a letter box is displayed

(black lines at the top/bottom of the screen) when using video software.

True size

The image is projected with the original resolution of the input signal. Select this to

clearly project a computer screen image which has a resolution of WUXGA or lower.

This can only be selected when the screen aspect is 16:10.

There may be some cases when this cannot be selected, depending on the input signal and/or

resolution.

There may be some cases when this cannot be selected, depending on the input signal and/or

resolution.

Adjusting the Image

How to Select an Aspect Ratio

Press the ASPECT button on the remote control and select an appropriate aspect ratio. Press the

ASPECT button to change the aspect ratio type.

For more details about aspect ratios, refer to

page 207

You can also select any aspect ratio from [Aspect] in the menu. (P93)

Some aspect ratios may not appear depending on the type of input signal.

Example:

Remote control

Adjusting the Image

User’s Manual Projectin

an Ima

Adjusting the Image Size

The size of the projected image can be adjusted by pressing the ZOOM button on the

remote control or the LENS button on the projector. Change the projector installation posi-

tion if your desired image is too large or too small to adjust it with the zoom function.

(P156)

1Press either the ZOOM button on the remote control or the LENS button on the projec-

tor twice in order to display the window shown below.

Push twice

Remote control Projector Remote control

Adjusting the Image

2Press the pointer buttons to adjust the image size.

3When the desired image size is selected, press the OK button or the ZOOM button.

When the Short Fixed Lens (RS-IL03WF) is attached, zoom adjustment cannot

be performed.

Use the [] button on the remote control, or the UP button on the projector to

increase the image size.

Use the [] button on the remote control, or the DOWN button on the projector to

decrease the image size.

Remote control Projector Remote control

Screen

Adjusting the Image

User’s Manual Projectin

an Ima

Adjusting the Focus

To adjust the focus, press the FOCUS button on the remote control or the LENS button on

the projector.

For the projection distances of the lens unit, refer to page 156.

1Press either the FOCUS button on the remote control or the LENS button on the pro-

jector in order to display the window shown below.

2Press the pointer buttons to adjust the focus.

3When the focus is adjusted optimally, press the OK button or the FOCUS button.

Remote control Projector Remote control

Use the [] button on the remote control, or the UP button on the projector to adjust the

focus position.

Use the [] button on the remote control, or the DOWN button on the projector to per-

form fine adjustment.

Remote control Projector Remote control

Adjusting the Image

Adjusting the Image Position

To adjust the screen position up, down, left, or right, press the LENS-SHIFT button

(WUX5000 / WUX4000) or SHIFT button (WX6000 / SX6000) on the remote control, or the

LENS button on the projector. This function is referred to as “lens shift”. It can change the

projected screen to the most suitable position by moving the position of the lens up/down/

left/right. (P160)

1Press either the LENS-SHIFT button (WUX5000 / WUX4000) or the SHIFT button

(WX6000 / SX6000) on the remote control, or the LENS button on the projector 3

times in order to display the window shown below.

* If the Short Fixed Focus Lens (RS-IL03WF) is attached, when the LENS button on

the projector is pressed twice, the window below will be displayed.

• The available range for lens shift (percentage of movement relative to the screen size) var-

ies depending on the lens unit which is used. (P161)

• There are areas where each lens is unable to move. With the Short Fixed Lens (RS-

IL03WF), the areas are at the four corners and for the other lenses, the areas are at the top

left and bottom right. (P161)

Push three times*

Remote control Projector Remote control

Adjusting the Image

User’s Manual Projectin

an Ima

2Press the pointer buttons to adjust.

3When the desired position is reached, press the OK button.

■Resetting the Position

The lens position after movement with the lens shift function is not returned when the

power is turned off. To return it to its original position, perform reset.

During screen position adjustment, press and hold the LENS-SHIFT button (WUX5000 /

WUX4000) or SHIFT button (WX6000 / SX6000) on the remote control, or the LENS button

on the projector to display the [Lens shift Reset] window.

The selections for the lens currently used are displayed. Use the pointer buttons to select

one of them, then press the OK button.

Lens unit type Available items

Standard Zoom Lens

RS-IL01ST

50% (Home position) : Up 50%, left / right 0%

0% : Up / down / left / right 0%

Long Zoom Lens

RS-IL02LZ

Ultra Long Zoom Lens

RS-IL04UL

Short Fixed Lens

RS-IL03WF 0% (Home position) : Up / down / left / right 0%

Remote control Projector

Screen

Remote control

Adjusting the Image

Adjusting Keystone Distortion

The D.SHIFT/KEYSTONE button (WUX5000 / WUX4000) or KEYSTONE button

(WX6000 / SX6000) can be used to correct keystone distortion.

1Press the D.SHIFT/KEYSTONE button (WUX5000 / WUX4000) or KEYSTONE button

(WX6000 / SX6000) to display the window in the center illustration below.

• Keystone can be adjusted within the range of ±20 degrees. If the keystone distortion is

too large to adjust, move the projector installation position so that it is completely straight.

• The result of keystone adjustment is stored in memory. If you place the projector in the

same position, the keystone adjustment is not necessary.

• Signals are processed digitally when keystone distortion is corrected. The image may

look different from the original one. In addition, the aspect ratio of the image may change.

• Perform keystone distortion correction with the lens shift position in the home position. Cor-

rection will not be performed correctly if the position is not the home position.

Remote control Remote control

Adjusting the Image

User’s Manual Projectin

an Ima

2Press the pointer buttons to adjust.

3When keystone distortion has been corrected, press the OK button.

■Resetting the Keystone Adjustment

Perform the following steps to reset the keystone adjustment.

Press the D.SHIFT/KEYSTONE button (WUX5000 / WUX4000) or KEYSTONE button

(WX6000 / SX6000) twice to display the [Keystone reset] window.

Then, select [OK] with the [ ] button, and press the OK button.

Remote control Projector

[ ] button

Reduces the dimensions of the upper edge

[ ] button

Reduces the dimensions of the lower edge

[] button

Reduces the dimension of the left edge

[ ] button

Reduces the dimension of the right edge

Screen

Remote control

Selecting an Image Mode

You can select an image mode to suit the projected image.

In each image mode, you can further adjust the brightness, contrast, sharpness, gamma,

color adjustment, advanced adjustment, and lamp mode (WUX4000). (P109)

■Image Modes

The image modes which can be selected vary somewhat depending on the selected

input signal.

Image

Mode

Compatible input signals

Explanation

Digital PC

Analog PC

(WUX5000 / WUX4000)

Analog PC-1, 2

(WX6000 / SX6000)

HDMI (when [HDMI

In] is [Computer])

Component HDMI

(when [HDMI In] is

[Auto])

Standard

Suitable for projecting a computer

screen or watching media played with

video software in a brightish room.

This image mode emphasizes white

tones.

Presenta-

tion

Suitable for viewing text-based images

in a brightish room.

Dynamic Suitable for watching media played

with video software in a brightish room.

VividPhoto

Suitable for viewing images with

vibrant colors in a moderately dark

room.

This image mode emphasizes color

saturation.

Photo/

sRGB

Suitable for viewing images taken with

a digital camera that supports sRGB in

a moderately dark room.

This image mode supports the sRGB

standard.

Video

Suitable for watching video taken with

a video camera in a moderately dark

room.

Cinema

Suitable for watching media played

with video software in a dark room.

This image mode enables viewers to

enjoy the atmosphere of a movie the-

ater.

User 1 - 5 * *

* Up to 5 user-selected combinations

of image quality settings can be

stored in the memory. (P110) Stored

settings can be selected as an image

mode.

: Compatible : Not compatible

Selecting an Image Mode

User’s Manual Projectin

an Ima

■How to Select an Image Mode

Press the IMAGE button on the remote control to select.

The image mode changes each time the IMAGE button is pressed. (The displayed image

modes vary depending on the selected input signal.)

You can also select any image mode from the [Image mode] menu. (P109)

• User settings 1 - 5 are displayed when the desired image settings have been created

and stored using the user memory function in the image adjustment menu. (P110)

Remote control

Turning Off the Projector

1Press the POWER button to display the window shown below.

When this window is displayed, press the POWER button again to turn off the power.

The lamp goes off, the [STAND BY] indicator starts flashing in red and the cooling

process starts.

2Disconnect the power cord from the electrical outlet.

If the power plug is left connected, the [STAND BY] indicator will switch from flashing

to constantly illuminated after the cooling process is completed.

• You cannot turn the projector on while the cooling process is in operation.

• If you want to continue projecting without turning off the power, press a button other than

POWER, or else wait until the confirmation message disappears.

• After turning off the projector, wait at least 5 minutes before turning it on again. It may shorten

the lamp life if you turn on the projector immediately after turning it off.

• Using the projector for a long time may shorten the life of the lamp and internal optical

components.

Remote control Projector Remote control

Useful Functions Available

During a Presentation

User’s Manual

Safety Instructions

Before Use

Table of Contents

Appendix

Index

Appendix

Installation

Connecting to a Network

Projecting an Image

Setting Functions from Menus

Maintenance

Installation Manual

Useful Functions

Available During

a Presentation

Useful Functions Available During a Presentation

Temporarily Blacking Out

an Image

Press the BLANK button to black out the

image.

Press the BLANK button again to show the

image.

• You can set the screen state while black-

ing out the image in the menu. (P106)

• The lamp remains illuminated while the

image is blacked out.

Freezing the Picture

Press the FREEZE button to freeze the

moving image. The projector shows the

following icon.

Press the FREEZE button again to cancel

the FREEZE function.

• It is also cancelled when the input signal is

terminated.

Useful when:

• You have finished the presentation.

• You want to divert attendees’ attention from

the screen.

Remote control

Useful when:

• You want to perform a computer operation

which is irrelevant to the proceedings of the

presentation.

• You want to stop a moving image.

Remote control

Screen

Useful Functions Available During a Presentation

User’s Manual Useful Functions Available During a Presentation

Adjusting the Volume

Press the VOL button. The following

screen appears.

• You can also adjust the volume level with

the [] / [] buttons of the projector.

• Adjust the volume or mute setting on the

computer if the volume level is too low.

• You can also adjust the volume level of the

speakers connected via the audio output

terminal.

Muting the Sound

Press the MUTE button to mute the sound.

The projector shows the following icon.

Press the

MUTE

button again to cancel the

mute function.

• You can also mute the sound of the speak-

ers connected via the audio output termi-

nal.

For the WX6000 / SX6000, depending

on whether the AUDIO IN terminal has

been set in the Audio in terminal select

screen (P139), there may be no audio

output in some cases.

Useful when:

• You want to adjust the volume level of the

projector or external speakers.

Remote control

Useful when:

• You want to temporality mute unnecessary

sound.

• You want to immediately mute the sound.

Remote control

Screen

Useful Functions Available During a Presentation

Zooming an Image

Press the + D.ZOOM button to enlarge a

part of the image. Press the - D.ZOOM

button to reduce the image size.

• The magnification appears on the screen.

You can move the area you want to zoom in

on by using the

[] / [] / [] / []

buttons.

You can restore the original size of the

image by pressing the OK button.

Useful when:

• Zooming in on an object such as a small

graph during a presentation (up to 12x).

• Focusing on the current subject.

スクリーン

Screen

Remote control

Screen

Remote control

Useful Functions Available During a Presentation

User’s Manual Useful Functions Available During a Presentation

Showing the Elapsed

Time

Press the P-TIMER button to start counting.

• The elapsed time is displayed on the lower

right corner of the screen.

• Time is counted up to 59:59. The timer

then returns to 00:00.

Press the P-TIMER button again to stop

the timer.

• Press the P-TIMER button while the timer

is stopped. The timer disappears from the

screen. Then press the P-TIMER button to

start counting from 00:00.

Useful when:

• You want to manage the timing of the presen-

tation.

Screen

Remote control

Projecting an Image

Safety Instructions

Before Use

Table of Contents

Useful Functions Available

During a Presentation

Setting Functions from Menus

User’s Manual

Installation

Connecting to a Network

Maintenance

Appendix

Index

AppendixInstallation Manual

Setting Func-

tions from Menus

How to Use Menus

Use the menus to set the operation of the projector in detail.

■Menu Configuration

The menu screen is divided into 5 tabs as shown below.

Input Signal Types for which a Menu Item is Displayed

Different menu items are displayed for different input signal types.

In the following explanation of each menu item, the input signal type for which the

menu item is displayed is indicated as follows:

Contents of menu Menu items

[Display settings] tab

You can set the type of signal

or the method of projection of

the images input.

[

System settings] tab

You can set the operation of the projector.

[Image adjustment] tab

You can adjust the image quality

and colors according to your

preference.

[Network setting] tab

These settings are for when using the

projector from a PC via a network.

For the network settings, refer to page

165.

[Information] tab

You can check information about the

signal types of the images projected

and other projector-specific informa-

tion.

HDMI Component

Digital PC Analog PC

Input signal for which the

menu item is displayed

Input signal for which the

menu item is not displayed

How to Use Menus

User’s Manual Settin

Functions from Menus

The menu screen is divided into 6 tabs as shown below.

Contents of menu Menu items

[Input settings] tab

You can set the type of signal or

the method of projection of the

images input.

[Image adjustment] tab

You can adjust the image qual-

ity and colors according to your

preference.

[Network setting] tab



These settings are for when using the

projector from a PC via a network.

For the network settings, refer to page

165.

[Information] tab

You can check information about the

signal types of the images projected

and other projector-specific informa-

tion.

[Install settings] tab

This setting is used when installing the projector.

[System settings] tab

You can set the operation of the projector.

How to Use Menus

■Basic Menu Operations

The menus shown below are for WUX5000.

1Press the [MENU] button to display the menu window.

2Use the [] / [] buttons to select a tab.

• If the tab position is not highlighted in orange, use the [ ] / [ ] buttons to move the

highlight to the top.

Remote control Projector Remote control

How to Use Menus

User’s Manual Settin

Functions from Menus

3Use the [] / [] buttons to select an item.

Remote control Projector Remote control

How to Use Menus

4Select contents.

How to select the contents varies depending on the item.

Selecting from a list Example: Aspect

Adjusting with the [ ] / [ ] buttons Example: Contrast

Selecting from a different screen (1) Example: Menu position

Selecting from a different screen (2) Example: Tracking

5Pressing the MENU button causes the menu screen to disappear.

The menu screen will also disappear if the EXIT button (WX6000 / SX6000) is

pressed.

1. Select Aspect.

2. Press the OK button or [ ] button to dis-

play a list of the contents.

3. Use the [ ] / [ ] buttons to select the

desired contents.

4. When you have found the contents you

desired, press the OK button or [ ].

1. Select Contrast.

2. Use the [ ] / [ ] buttons to adjust the set-

ting.

1. Select Menu position.

2. Press the OK button to display a different

screen.

3. Then follow the instruction on the screen.

1. Select Input signal settings.

2. Select Tracking.

3. Press the OK button to display a different

screen.

4. Use the [ ] / [ ] buttons to select the set-

ting, then use the [ ] / [ ] buttons to select

the value.

5. When you have completed the settings,

press the OK button.

User’s Manual Settin

Functions from Menus

Setting Display Status

Selecting an Image Pro-

jection Mode

[Aspect]

You can select a projection mode corre-

sponding to the aspect ratio of the image.

(P69)

MENU > [Display settings] > [Aspect]

MENU > [Input settings] > [Aspect]

• Different contents are displayed for differ-

ent screen aspects or input signal types.

•The ASPECT button on the remote control

can also be used to select the Aspect set-

tings.

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

HDMI Component

Digital PC Analog PC

Auto An image is projected at the

aspect ratio of the input signal.

Select this mode for normal image

projection.

Full (WUX5000 / WUX4000)

The image is projected using an

input signal aspect ratio of 16:10.

Select this to project computer

screen images with an aspect ratio

of 16:10 (WUXGA, WSXGA+,

WXGA+ and WXGA (1280 x 800))

fully on the screen.

16:10 (WX6000 / SX6000)

The image is projected using an

input signal aspect ratio of 16:10.

16:9 The image is projected using an

input signal aspect ratio of 16:9.

Select this if an image of 16:9

aspect ratio cannot be correctly

projected in [Auto] mode.

4:3 The image is projected using an

input signal aspect ratio of 4:3.

Select this if an image of 4:3

aspect ratio cannot be correctly

projected in [Auto] mode.

Zoom This cuts the upper/lower or left/

right part of the screen according

to the screen aspect and zooms in

or out of the center of the image.

Select this if a letter box is dis-

played (black lines at the top/bot-

tom of the screen) when using

video software.

True size

The image is projected with the origi-

nal resolution of the input signal.

Select this to clearly project a computer

screen image that has a resolution of

WUXGA and lower (WUX5000 /

WUX4000), WXGA+ and lower

(WX6000) or SXGA+ and lower

(SX6000).

This can only be selected when

the screen aspect is 16:10.

There may be some cases when

this cannot be selected, depend-

ing on the input signal and/or reso-

lution.

There may be some cases when

this cannot be selected, depend-

ing on the input signal and/or reso-

lution.

Setting Display Status

Automatic Display

Adjustment

[Auto PC]

Automatically adjusts display position mis-

alignment and screen flickering. The

adjusted result is stored in the memory.

MENU > [Input settings] > [Auto PC]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

Selecting an Input Signal

Type (Analog PC)

[Input signal select]

You can select a suitable resolution if the

auto PC adjustment function (P62) cannot

project the correct image from a computer.

MENU > [Display settings] > [Input signal select]

MENU > [Input settings] > [Input signal select]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

Select an input signal corresponding to

the resolution of the computer.

• For the signal types supported by the pro-

jector, see the table on page 218.

HDMI Component

Digital PC Analog PC

If [Auto PC] adjustment is insufficient,

perform the following operations.

• Select the input signal that matches

the resolution of the computer from

[Input signal select]. (P94)

• If adjustment is insufficient even

when using the above operation,

adjust [Total dots], [Tracking], [Hori-

zontal/Vertical position] and [Hori-

zontal/Vertical pixels] in [Input signal

settings]. (P95 – P98)

• For details about signal formats that

are compatible with the projector,

refer to page 218.

HDMI Component

Digital PC Analog PC

Setting Display Status

User’s Manual Settin

Functions from Menus

Selecting an Input Signal

Type (Component)

[Input signal select]

You can select the proper component sig-

nal type if the video image from AV equip-

ment is not projected correctly.

MENU > [Display settings]> [Input signal select]

Press the OK button to accept your setting

and then press the MENU button.

• [Auto] is the factory default.

• Refer to the user’s manual for the AV

equipment connected to the projector to

confirm the component signal type.

Adjust Input Signal Type

(Analog PC) Total Dots

[Total dots]

You can adjust the total number of dots in

the horizontal direction.

Adjust it when stripes are displayed on the

screen.

MENU > [Display settings]> [Input signal set-

tings] > [Total dots]

MENU > [Input settings] > [Input signal

settings] > [Total dots]

Use [ ] / [ ] to select a value.

When you have completed the adjust-

ment, press the OK button to accept your

setting and then press the MENU button

or EXIT button (WX6000 / SX6000).

• Perform this adjustment if the [AUTO PC]

function (P62) cannot adjust the projected

image correctly.

HDMI Component

Digital PC Analog PC

HDMI Component

Digital PC Analog PC

Setting Display Status

Adjust Input Signal Type

(Analog PC) Tracking

[Tracking]

You can fine-tune the timing for generating

an image from the image signal.

Adjusts the tracking when the image dis-

torts or flickers.

MENU > [Display settings]> [Input signal set-

tings] > [Tracking]

MENU > [Input settings] > [Input signal

settings] > [Tracking]

Use [ ] / [ ] to select a value.

When you have completed the adjust-

ment, press the OK button to accept your

setting and then press the MENU button

or EXIT button (WX6000 / SX6000).

• Perform this adjustment if the [AUTO PC]

function (P62) cannot adjust the projected

image correctly.

Adjust Input Signal Type

(Analog PC) Horizontal

Position

[Horizontal position]

You can adjust the horizontal position of

the screen when the projected image is

shifted in the horizontal direction.

MENU > [Display settings]> [Input signal set-

tings] > [Horizontal position]

MENU > [Input settings] > [Input signal settings]

> [Horizontal position]

Use [ ] / [ ] to select a value. As the

value increases, the screen moves to the

left.

When you have completed the adjust-

ment, press the OK button to accept your

setting and then press the MENU button

or EXIT button (WX6000 / SX6000).

• Perform this adjustment if the [AUTO PC]

function (P62) cannot adjust the projected

image correctly.

HDMI Component

Digital PC Analog PC HDMI Component

Digital PC Analog PC

Screen

Setting Display Status

User’s Manual Settin

Functions from Menus

Adjust Input Signal Type

(Analog PC) Vertical Posi-

tion

[Vertical position]

You can adjust the vertical position of the

screen when the projected image is shifted

in the vertical direction.

MENU > [Display settings]> [Input signal set-

tings] > [Vertical position]

MENU > [Input settings] > [Input signal

settings] > [Vertical position]

Use [ ] / [ ] to select a value. As the

value increases, the screen moves

upward.

When you have completed the adjust-

ment, press the OK button to accept your

setting and then press the MENU button

or EXIT button (WX6000 / SX6000).

• Perform this adjustment if the [AUTO PC]

function (P62) cannot adjust the projected

image correctly.

Adjust Input Signal Type

(Analog PC) Horizontal

Pixels

[Horizontal pixels]

You can adjust the number of the pixels in

the horizontal direction if the length of the

screen is too long or too short in the hori-

zontal direction.

MENU > [Display settings]> [Input signal set-

tings] > [Horizontal pixels]

MENU > [Input settings] > [Input signal

settings] > [Horizontal pixels]

Use [ ] / [ ] to select a value.

When you have completed the adjust-

ment, press the OK button to accept your

setting and then press the MENU button

or EXIT button (WX6000 / SX6000).

• Perform this adjustment if the [AUTO PC]

function (P62) cannot adjust the projected

image correctly.

HDMI Component

Digital PC Analog PC

Screen

HDMI Component

Digital PC Analog PC

Screen

Setting Display Status

Adjust Input Signal Type

(Analog PC) Vertical Pixels

[Vertical pixels]

You can adjust the number of the pixels in

the vertical direction if the screen is too

long or too short in the vertical direction.

MENU > [Display settings] > [Input signal set-

tings] > [Vertical pixels]

MENU > [Input settings] > [Input signal

settings] > [Vertical pixels]

Use [ ] / [ ] to select a value.

When you have completed the adjust-

ment, press the OK button to accept your

setting and then press the MENU button

or EXIT button (WX6000 / SX6000).

• Perform this adjustment if the [AUTO PC]

function (P62) cannot adjust the projected

image correctly.

Selecting HDMI Input

Level

[HDMI input level]

You can select this as required when you

project visual software with an HDMI sig-

nal.

MENU > [Display settings] > [HDMI input level]

MENU > [Input settings] > [HDMI input level]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [Auto] is the factory default.

• You can select this only when the type of sig-

nal sent from AV equipment is RGB.

• The signal level is selected automatically in

[Auto] mode. (Some AV equipment may not

support this.)

• If the HDMI output of your AV equipment

allows switching between [Normal] and

HDMI Component

Digital PC Analog PC

Screen

HDMI Component

Digital PC Analog PC

Setting Display Status

User’s Manual Settin

Functions from Menus

[Expanded], we recommend you to set

[Expanded]. The contrast of images will be

improved and dark scenes will be rendered

more realistically. In this case, select [Auto]

or [Expanded] for the HDMI input level.

For more detailed information, refer to the

user’s manual for the AV equipment con-

nected to the projector.

HDMI Color Format

[HDMI color space]

Select the color space for the HDMI signal.

MENU > [Display settings] > [HDMI color space]

MENU > [Input settings] > [HDMI color space]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [Auto] is the factory default.

HDMI Component

Digital PC Analog PC

Auto Selects the optimal color format

for the input HDMI signal.

RGB Forces the projector to handle the

input signal as an RGB signal.

YCbCr Forces the projector to handle the

input signal as a color difference

signal.

Setting Display Status

100

Select HDMI Over Scan

[HDMI over scan]

You can select this as required when you

project visual software using an HDMI sig-

nal.

MENU > [Display settings] > [HDMI over scan]

MENU > [Input settings] > [HDMI over scan]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• The factory defaults settings are [On]

when [HDMI In] (P127) is set for [Auto]

and [Off] when it is set for [Computer].

HDMI Component

Digital PC Analog PC

Off The entire input signal (100%) is pro-

jected. The images projected may be

smaller than the full projection screen.

On Images are projected with distortion

at the peripheral section of images

trimmed off. (The central 95% of the

images are projected.)

Part of the peripheral sections of

images may be cut out depending on

the resolution of the signal. In such a

case, select [Off].

101

Setting Display Status

User’s Manual Settin

Functions from Menus

Performing Progressive

Processing

[Progressive]

You can select this as required when the

images have low resolution.

MENU > [Display settings] > [Progressive]

MENU > [Input settings] > [Progressive]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

•[Auto] is the factory default.

• When [HDMI In] (P127) is [Computer], this

can only be set when the input signal is

1080i, 1035i, 576i or 480i and the input

signal color space is YCbCr422.

• Select [Off] when flickers and horizontal

lines are noticeable in media that has a lot

of fast-moving action.

HDMI Component

Digital PC Analog PC

Off Does not perform progressive

processing.

On Performs progressive processing.

This mode is available when the

HDMI signal is 1080i, or compo-

nent signal is 1080i, 1035i, 576i

or 480i.

Auto Performs the appropriate pro-

gressive processing according to

the input signal.

Setting Display Status

102

Selecting a Menu Position

[Menu position]

You can change the position of menus dis-

played.

MENU > [Display settings] > [Menu position]

MENU > [Install settings] > [On screen] > [Menu

position]

Move the menu to the desired position

with the [ ] / [ ] / [ ] / [ ] buttons.

When the menu has been moved to the

desired position, press the OK, MENU or

EXIT button (WX6000 / SX6000).

HDMI Component

Digital PC Analog PC

103

Setting Display Status

User’s Manual Settin

Functions from Menus

Correcting the Screen

Color

[Screen color]

You can adjust the color quality of the

images projected according to the color of

the projection screen.

MENU > [Display settings] > [Screen color]

MENU > [Install settings] > [Screen color]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [Normal] is the factory default.

HDMI Component

Digital PC Analog PC

Normal Select this if a standard type of pro-

jection screen is used. The images

are projected in a light quality similar

to that of natural light.

Green-

board

Select this if a greenboard (dark

green color) is used for the projec-

tion screen. The color quality similar

to [Normal] is obtained on the

greenboard.

Adjust Select this to make detailed adjust-

ment.

The following popup screen will

appear.

Use the [ ] / [ ] buttons to select a

primary color.

[]

makes the color selected darker.

[] makes the color selected lighter.

Setting Display Status

104

Reversing Projection

[Image flip H/V]

Select this setting if you want to hang the

projector from the ceiling or project an

image from behind the screen.

MENU > [Display settings] > [Image flip H/V]

MENU > [Install settings] > [Image flip H/V]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [None] is the factory default.

HDMI Component

Digital PC Analog PC

None Select this to project an image

normally.

Ceiling

mounted

Select this to project an image

with the projector hung from the

ceiling.

The projected image is inverted

in both vertical and horizontal

directions.

Rear Select this to project an image

from behind the screen.

The projected image is inverted

in the horizontal direction.

Rear, Ceil-

ing mounted

Select this to project an image

from behind the screen with the

projector hung from the ceiling.

The projected image is inverted

in the vertical direction.

105

Setting Display Status

User’s Manual Settin

Functions from Menus

• To hang the projector from the ceiling, use

the optional bracket. Contact the Canon

Customer Support Center for more

detailed information.

• If you flip the image, the keystone distor-

tion adjustment will be reset.

No Signal Screen

[No signal screen]

You can display either a black or blue

screen when there is no input signal.

MENU > [Display settings]> [User screen set-

tings] > [No signal screen]

MENU > [System settings] > [User screen set-

tings] > [No signal screen]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [Blue] is the factory default.

Normal projection (none)

Ceiling mounted projection

Rear projection

Rear ceiling mounted projection

HDMI Component

Digital PC Analog PC

Black The screen is all black.

Blue The screen is all blue.

Setting Display Status

106

Screen When Blank

[Screen when blank]

You can display a black or blue screen and

temporarily blank out the projected image

by pressing the BLANK button on the

remote control.

MENU > [Display settings] > [User screen set-

tings] > [Screen when blank]

MENU > [System settings] > [User screen set-

tings] > [Screen when blank]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [Black] is the factory default.

Selecting a Logo at Star-

tup

[Projector on]

You can display a specified logo on the

screen from the moment the projector is

turned on to the moment it is ready for pro-

jection.

MENU > [Display settings] > [User screen set-

tings] > [Projector on]

MENU > [System settings] > [User screen set-

tings] > [Projector on]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [Canon logo] is the factory default.

HDMI Component

Digital PC Analog PC

Black The screen is all black.

Blue The screen is all blue.

HDMI Component

Digital PC Analog PC

Skip Projects an input signal

immediately after turning on

the projector.

Canon logo

Displays the Canon logo that

was registered in advance at

the factory.

107

Setting Display Status

User’s Manual Settin

Functions from Menus

Selecting Aspect Ratio of

Screen

[Screen aspect]

Select according to the aspect ratio of the

projection screen. (P63)

MENU > [Display settings]> [Screen aspect]

MENU > [Install settings] > [Screen aspect]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• The factory default is [16:10] for the

WUX5000 / WUX4000 / WX6000, and [4:3]

for the SX6000.

• If you select [16:9 D. image shift], [4:3 D.

image shift], or [16:10 D. image shift] (for

SX6000), the keystone correction will be

canceled. For more details, refer to page

66.

• [Auto] may be automatically selected for

the aspect depending on the screen

aspect setting.

HDMI Component

Digital PC Analog PC

16:10 Select this when you use a screen

with an aspect ratio of 16:10.

16:9 Select this when you use a screen

with an aspect ratio of 16:9.

4:3 Select this when you use a screen

with an aspect ratio of 4:3.

16:10 D

image

shift

(SX6000)

Select this when the screen

aspect ratio is 16:10. Keystone

correction cannot be performed in

this mode. However when project-

ing level, it is possible to shift the

image up or down. For details

about how to shift the image, refer

to page 67.

16:9

image

shift

Select this when you use a screen

with an aspect ratio of 16:9.

Keystone correction cannot be

performed in this mode. However,

it is possible to move the image

up / down when projecting level.

For details about how to move the

image, refer to page 67.

4:3

image

shift

(Except

for

SX6000)

Select this when you use a screen

with an aspect ratio of 4:3.

Keystone correction cannot be

performed in this mode. However,

it is possible to move the image

left / right when projecting level.

For details about how to move the

image, refer to page 68.

Setting Display Status

108

Adjusting Keystone Dis-

tortion

[Keystone adjustment]

Corrects keystone distortion.

MENU > [Install settings] > [Keystone adjust-

ment]

If the OK button or [ ] button is pressed,

the Keystone adjustment screen is dis-

played.

Correct using the [ ] / [ ] / [ ] / [ ] but-

tons. When you have finished correcting,

press the OK button.

• This cannot be selected when the screen

aspect is 16:9D image shift, 16:10D image

shift or 4:3D image shift.

• The Keystone adjustment screen can also be

displayed by pressing the KEYSTONE but-

ton on the remote control. (P76)

Image Shift Adjustment

[Digital image shift]

Moves the position of the projected image.

MENU > [Install settings] > [Digital image shift]

If the OK button or [ ] button is pressed,

the D image shift adjustment screen is dis-

played.

Correct using the [ ] / [ ] buttons. When

you have finished correcting, press the OK

button.

• This cannot be selected when the screen

aspect is 16:9, 16:10 or 4:3.

• When the screen aspect is 16:9D image shift

or 16:10D image shift (SX6000), the image

can be adjusted vertically, and when the

screen aspect is 4:3D image shift (WX6000),

it can be adjusted horizontally.

HDMI Component

Digital PC Analog PC

HDMI Component

Digital PC Analog PC

109

User’s Manual Settin

Functions from Menus

Selecting an Image Quality

Image Adjustment

[Image mode]

You can select an image mode suitable for

the projected image. (P78)

You can also select it with the IMAGE but-

ton on the remote control. (P79)

MENU > [Image adjustment] > [Image mode]

(The screen is for the WUX5000.)

MENU > [Image adjustment] > [Image mode]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [Standard] is the factory default.

• You can adjust the image quality by

adjusting the following items in each

image mode:

[Brightness], [Contrast], [Sharpness],

[Gamma], [Color adjustment],

[Advanced adjustment] and [Lamp

mode] (WUX4000)

• The adjustment you have made is

stored as each combination of input sig-

nals and an image mode.

• When a user memory that was saved in

[Create profile] is selected, [Baseline

Image Mode] appears in the menu. This

indicates the image mode that was the

base when the user memory was saved.

HDMI Component

Digital PC Analog PC

Standard Suitable for projecting a computer

screen or watching media played

with video software in a brightish

room.

This image mode emphasizes

white tones.

Presenta-

tion

Suitable for viewing text-based

images in a brightish room.

Dynamic Suitable for watching media

played with video software in a

brightish room.

VividPhoto Suitable for viewing images with

vibrant colors in a moderately

dark room.

This image mode emphasizes

color saturation.

Photo/

sRGB

Suitable for projecting images

taken with a digital camera that

supports sRGB in a moderately

dark room. Supports the sRGB

standard.

Video Suitable for watching video taken

with a video camera in a moder-

ately dark room.

Cinema Suitable for watching media

played with video software in a

dark room.

This image mode enables viewers

to enjoy the atmosphere of a

movie theater.

User 1 - 5 Up to 5 user-selected combina-

tions of image quality settings can

be stored in the memory. (P110)

Stored settings can be selected

as an image mode.

Selecting an Image Quality

110

(The screen is for the WUX5000.)

Saving the Desired Image

Quality

[Create profile]

Up to 5 combinations of image quality set-

tings can be stored. The stored image

quality can be selected as an image mode.

MENU > [Image adjustment] > [Create Profile]

(The screen is for the WUX5000.)

MENU > [Image adjustment] > [Create profile]

Use the [ ] / [ ] buttons and select the

save destination. (Saved memories are

indicated by checkmarks.)

HDMI Component

Digital PC Analog PC

111

Selecting an Image Quality

User’s Manual Settin

Functions from Menus

When the desired save destination is

selected, press the OK button to accept

your setting and then press the [Return]

button.

• The saved settings consist of the brightness,

contract, sharpness, gamma, color adjust-

ment, advanced adjustment, and lamp mode

(WUX4000).

• The number of displayed user memories is 5,

however it is possible to save different set-

tings for when the connected equipment is a

computer (ANALOG PC, DIGITAL PC or

HDMI (when [HDMI In] (P127) is [Computer])

and when AV equipment is connected (COM-

PONENT, HDMI (when [HDMI In] (P127) is

[Auto])). As a result, it is possible to save up

to 10 settings.

• The image mode name which was the basis

for the settings change is also saved in the

user memory. When a user memory is

selected as the image mode, the image

mode that was the base for that user memory

is displayed in the menu as [Baseline image

mode].

Adjusting the Brightness

[Brightness]

You can adjust the brightness of images.

MENU > [Image adjustment] > [Brightness]

(The screen is for the WUX5000.)

MENU > [Image adjustment] > [Brightness]

When you have completed the adjust-

ment, press the OK button to accept your

setting and then press the MENU button

or EXIT button (WX6000 / SX6000).

• The adjustment you have made is stored

as adjusted values for the input signals

and image mode of the current projection.

HDMI Component

Digital PC Analog PC

[ ] Increases the brightness of an image.

[ ] Decreases the brightness of an image.

Selecting an Image Quality

112

Adjusting the Contrast

[Contrast]

You can adjust the contrast of images.

Adjust the difference between the light and

dark parts of the image to produce an

image with emphasized contrast or an

image that is soft.

MENU > [Image adjustment] > [Contrast]

(The screen is for the WUX5000.)

MENU > [Image adjustment] > [Contrast]

When you have completed the adjust-

ment, press the OK button to accept your

setting and then press the MENU button

or EXIT button (WX6000 / SX6000).

• The adjustment you have made is stored

as adjusted values for the input signals

and image mode of the current projection.

HDMI Component

Digital PC Analog PC

[ ] Increases the contrast of an image.

This emphasizes the darker and

brighter parts of the image on the pro-

jected image.

[ ] Decreases the contrast of an image.

The image becomes less vivid.

113

Selecting an Image Quality

User’s Manual Settin

Functions from Menus

Adjusting the Sharpness

[Sharpness]

You can adjust the sharpness of images.

MENU > [Image adjustment] > [Sharpness]

(The screen is for the WUX5000.)

MENU > [Image adjustment] > [Sharpness]

When you have completed the adjust-

ment, press the OK button to accept your

setting and then press the MENU button

or EXIT button (WX6000 / SX6000).

• The adjustment you have made is stored

as adjusted values for the input signals

and image mode of the current projection.

Performing Gamma Cor-

rection

[Gamma]

You can correct portions of an image that

are difficult to see because they are too

dark or bright.

For the WUX5000 / WUX4000, correction

can be made by using the GAMMA button

on the remote control.

MENU > [Image adjustment] > [Gamma]

(The screen is for the WUX5000.)

MENU > [Image adjustment] > [Gamma]

When you have completed the adjust-

ment, press the OK button to accept your

HDMI Component

Digital PC Analog PC

[ ] Increases the sharpness of an image.

[ ] Decreases the sharpness of an image.

HDMI Component

Digital PC Analog PC

[ ] Brightens the dark portion

[ ] Darkens the bright portion

Selecting an Image Quality

114

setting and then press the MENU button

or EXIT button (WX6000 / SX6000).

• The adjustment you have made is stored

as adjusted values for the input signals

and image mode of the current projection.

• More detailed adjustment is possible by

using the detailed gamma correction

(P118).

Adjusting Color

[Color adjustment]

You can adjust the color depth and hue of

images for each primary color, red, green

and blue. The color temperature can also

be adjusted.

MENU > [Image adjustment] > [Color adjust-

ment]

When you have completed the adjust-

ment, press the OK button to accept your

setting and then press the MENU button

or EXIT button (WX6000 / SX6000).

• The adjustments you have made are

stored as adjusted values for the input sig-

nals and image mode of the current pro-

jection.

HDMI Component

Digital PC Analog PC

Color

level

Adjusts the intensity of each color.

[ ] Increases the intensity of color.

[ ] Decreases the intensity of color.

Color

balance

Adjusts the color balance of a purplish

or greenish image.

[ ] Corrects a purplish image.

[ ] Corrects a greenish image.

Color

temper-

ature

Adjusts the color temperature of the

image.

[]

Changes to a bluish color (cold color).

[]

Changes to a reddish color (warm color).

R / G / B

Gain

Adjust the intensity of each color.

[ ] Increases the color intensity.

[ ] Decreases the color intensity.

R / G / B

Offset

Adjusts the color reproducibility of

dark portions of each color.

[ ] Increases the color reproducibility.

[]

Decreases the color reproducibility.

115

Selecting an Image Quality

User’s Manual Settin

Functions from Menus

Correcting the Image

According to the Ambi-

ent Light

[Ambient light]

You can correct and more effectively

project an image according to the ambient

light on the screen.

MENU > [Image adjustment] > [Advanced

adjustment] > [Ambient light]

Examples of Ambient Light Level Settings

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [Off] is the factory default.

• [Ambient light] can be set only in the fol-

lowing image modes.

-HDMI (when [HDMI In] is [Auto]) or

COMPONENT:

Video, Cinema, Photo/sRGB

-HDMI (when [HDMI In] is [Computer]),

DIGITAL PC or ANALOG PC:

Photo/sRGB

HDMI Component

Digital PC Analog PC

Off Projects an image with no correc-

tion.

Adjust You can specify the type and

level (brightness) of the ambient

light.

Type Tungsten Select this if the

ambient light

source is a light

bulb or bulb color

fluorescent.

Fluorescent Select this if the

ambient light

source is a day

white fluorescent.

Fluorescent H Select this if the

ambient light

source is a day-

light color fluores-

cent.

Level L Select this if the ambient light

is low.

M Select this if the ambient light

is normal.

H Select this if the ambient light

is high (bright).

Level Example Location

LProjection room, sports bar, etc.

MPhoto studio, gallery

HConference room, lecture room

Selecting an Image Quality

116

Noise Reduction

[Noise reduction]

You can reduce image noise.

MENU > [Image adjustment] > [Advanced

adjustment] > [Noise reduction]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• The factory default for HDMI (when [HDMI

In] (P127) is set to [Auto]) is [Off] and

when Component is used, it is set to

[Weak].

• Noise reduction may produce motion arti-

facts when projecting fast-moving images.

• Select [Weak] for fast-moving images.

Select [Strong] for slow-moving images.

• The adjustment you have made is stored

as adjusted values for the input signals

and image mode of the current projection.

• When [HDMI In] (P127) is [Computer], this

setting is not displayed.

Dynamic Gamma

[Dynamic gamma]

You can adjust the gradation representa-

tion of light and dark portions of an image

automatically.

MENU > [Image adjustment] > [Advanced

adjustment] > [Dynamic gamma]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• The factory default settings are [Off] when

the connected equipment is a Computer

(ANALOG PC, DIGITAL PC, HDMI (when

[HDMI In] (P127) is [Computer])) and

[Weak] when the connected equipment is

AV equipment (COMPONENT, HDMI

(when [HDMI In] (P127) is [Auto])).

• The adjustment you have made is stored

as adjusted values for the input signals

and image mode of the current projection.

HDMI Component

Digital PC Analog PC

Off Disables noise reduction.

Weak

Middle

Strong

Specifies the intensity of the noise

reduction in three steps.

HDMI Component

Digital PC Analog PC

Off Dynamic gamma is disabled.

Weak

Middle

Strong

Specifies the intensity of the

dynamic gamma in three steps.

117

Selecting an Image Quality

User’s Manual Settin

Functions from Menus

Memory Color Correction

[Mem. color correct]

This function produces beautiful skin

tones, blues, and other colors.

MENU > [Image adjustment] > [Advanced

adjustment] > [Mem. color correct]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• The factory default settings are as follows.

-For HDMI (when [HDMI In] (P127) is set

to [Computer]), Digital PC and Analog

PC, when any image mode is used

except [VividPhoto], the default setting

is [Off]. When [VividPhoto] is used, the

default setting is [M].

-For HDMI (when [HDMI In] (P127) is set

to [Auto]) and Component, the default

setting is [L], regardless of the image

mode.

• The adjustment you have made is stored

as adjusted values for the input signals

and image mode of the current projection.

6-axis Color Adjust

(Detailed Color Adjust-

ment)

[6-axis color adjust]

You can make fine adjustments to the

image colors with RGB (red, green, blue)

and CMY (cyan, magenta, yellow).

MENU > [Image adjustment] > [Advanced

adjustment] > [6-axis color adjust]

When you have completed the adjust-

ment, press the OK button to accept your

setting and then press the MENU button

or EXIT button (WX6000 / SX6000).

• [Off] is the factory default.

• The adjustments you have made are stored

as adjusted values for the input signals and

image mode of the current projection.

HDMI Component

Digital PC Analog PC

Off Disables the memory color correc-

tion function.

Specifies the intensity of the memory

color correction in three steps.

HDMI Component

Digital PC Analog PC

Off Disables 6-axis color adjustment.

If you select [Adjust], the previous

setting of 6-axis color adjustment

becomes active again.

Adjust Enables 6-axis color adjustment.

Use the [ ] / [ ] buttons to select

[ Hue], [ Saturation], or [* Bright-

ness], then adjust them with the [ ] /

[ ] buttons.

When color adjustments are com-

pleted, press the OK button.

Reset Returns all adjustment values to zero.

Selecting an Image Quality

118

Detailed Gamma Correc-

tion

[Fine-Tune Gamma]

The four gamma curves (white, red, green,

blue) can be adjusted. When the white

curve is adjusted, the adjustment is also

applied to the other three colors. This func-

tion allows more fine-tuned gamma correc-

tion. When either of these two functions is

adjusted, the settings of the other are over-

written.

MENU > [Image adjustment] > [Advanced

adjustment] > [Fine-Tune Gamma]

Select [Fine-Tune Gamma] then press the

OK button. The following [Fine-Tune

Gamma] screen for confirmation appears.

Use the [ ] / [ ] buttons to select the

color, then press the OK button. Next use

the [ ] / [ ] buttons to select a point on

the gamma curve, and use the [ ] / [ ]

buttons to adjust the position of the point.

When you have completed the adjust-

ment, press the OK button to accept your

setting and then press the MENU button

or EXIT button (WX6000 / SX6000).

• The adjustments you have made are

stored as adjusted values for the input sig-

nals and image mode of the current pro-

jection.

• For details of gamma correction, refer to

page 113.

HDMI Component

Digital PC Analog PC

119

Selecting an Image Quality

User’s Manual Settin

Functions from Menus

Reducing the Lamp

Brightness

[Lamp mode]

Reducing the lamp brightness reduces

power consumption and cooling fan noise.

For the WUX4000, you can also enable or

disable this mode with the LAMP button on

the remote control.

MENU > [Image adjustment] > [Lamp mode]

Press the OK button to accept your setting

and then press the MENU button.

• [Normal] is the factory default.

• The adjustment you have made is stored

as adjusted values for the input signals

and image mode of the current projection.

Resetting the Image

Adjustment Settings

[Reset]

You can reset the current image adjust-

ment settings to the default settings. If

reset is performed when user setting 1 - 5

is selected for [Image mode], the settings

are returned to the settings that were

saved in [User setting 1 - 5].

MENU > [Image adjustment] > [Reset]

• Only the setting for the combination of

input signal and image mode for the cur-

rent projection is reset.

HDMI Component

Digital PC Analog PC

Normal Projects an image at the normal

brightness level.

Quiet Reduces the lamp brightness and

cooling fan noise.

HDMI Component

Digital PC Analog PC

OK Resets the image adjustment set-

tings.

Cancel Cancels resetting of the image

adjustment settings.

120

Setting Various Functions

Selecting the Power Man-

agement Mode

[Power management mode]

You can turn off the lamp or projector auto-

matically in order to save power when the

projector is not in use.

MENU > [System settings] > [Power manage-

ment mode]

MENU > [System settings] > [Power manage-

ment mode]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [Off] is the factory default.

• During standby mode, the [POWER ON]

indicator and [STAND BY] indicator flash

alternately.

• You cannot enable the [Direct power on]

function (see the next item), if you select

[Off].

HDMI Component

Digital PC Analog PC

Off Disables the power management

mode.

Standby If no input signal is received for 30

seconds, the countdown will be dis-

played and after 5 minutes, the

lamp will turn off.

If it receives an input signal or is

operated during this period, it

resumes projection.

Exit If no input signal is received for 30

seconds, it displays the countdown

and turns off the projector after 5

minutes.

121

Setting Various Functions

User’s Manual Settin

Functions from Menus

Skip the POWER Button

Operation

[Direct power on]

You can turn on the projector by connect-

ing the power cable without pressing the

POWER button.

MENU > [System settings] > [Direct power on]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [Off] is the factory default.

HDMI Component

Digital PC Analog PC

Off You need to press the POWER button

to turn on the projector.

On You can turn on the projector by con-

necting the power cable only.

• Before setting the direct power on to

[On], be sure to set the [Power man-

agement mode] to [Standby] or

[Exit].

•

After turning off the projector, wait at

least 5 minutes before turning it on

again. It may shorten the lamp life if

you turn on the projector immediately

after turning it off.

Setting Various Functions

122

Enabling / Disabling the

Beep

[Beep]

You can select whether a beep sounds or

not when you operate the projector.

MENU > [System settings] > [Beep]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [On] is the factory default.

• The beep will not sound if you mute the

projector sound with the MUTE button on

the remote control.

Key Repeat

[Key repeat]

By pressing and holding the button on the

projector or the remote control you can

operate Key repeat in the same was as

when the button is pressed repeatedly.

MENU > [System settings] > [Key repeat]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• The factory default is [On].

• Even when Key repeat is [Off], Focus adjust-

ment, Zoom Adjustment and Lens shift

adjustment can still be used.

HDMI Component

Digital PC Analog PC

Off Disables the beep.

On Enables the beep.

HDMI Component

Digital PC Analog PC

Off Key repeat is not enabled.

On Key repeat is enabled.

123

Setting Various Functions

User’s Manual Settin

Functions from Menus

Prohibiting Operations

[Key lock]

You can lock the projector to prevent its

operation from either the main unit or

remote control.

MENU > [System settings] > [Key lock]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [Off] is the factory default.

HDMI Component

Digital PC Analog PC

Off Disables the key lock.

Main

unit

Operation is not possible using the

main unit.

Use the remote control.

Remote

control

Infrared remote control operations

can no longer be performed. Use the

main unit button. If using the

WX6000 / SX6000, this can also be

set by connecting a cable. (P30)

The key lock function becomes effec-

tive from the moment the OK button is

pressed after selecting [Main unit] or

[Remote control]. Control via the item

selected will then be disabled.

To Unlock Key Lock Function

Turn off the projector and unplug the

power plug. Hold down the OK button

on the main unit and connect the

power plug. Keep holding down the

OK button until a beep sounds. The

key lock will be unlocked.

Setting Various Functions

124

Main Unit and Remote

Control Channel Settings

[Remote control]

When using multiple projectors at the

same time (maximum 4), you can assign a

different channel to each remote control so

that each operates independently.

For the WX6000 / SX6000, set this when

performing infrared operations.

Select the main unit channel.

MENU > [System settings] > [Remote control]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• The factory default is [Independent] for

both projector and remote control.

• After changing the channel on the menu,

be sure to change the channel of the

remote control too.

• If a cable is connected, it is not necessary

to perform remote control channel setting.

Selecting a Channel on the Remote control

You can change the channel on the

remote control as follows.

HDMI Component

Digital PC Analog PC

Ch1

Ch2

Ch3

Ch4

Select the remote control

channel to use with this

projector.

Independent Remote controls set to any

channel can be used.

Ch1 Press and hold the OK button

and [ ] button at the same time

for 3 seconds.

Ch2 Press and hold the OK button

and [ ] button at the same time

for 3 seconds.

Ch3 Press and hold the OK button

and [ ] button at the same time

for 3 seconds.

Ch4 Press and hold the OK button

and [ ] button at the same time

for 3 seconds.

Inde-

pendent

Press and hold the OK button

and MENU button at the same

time for 3 seconds.

Ch1 Press and hold the Ch button

and 1 button at the same time

for 3 seconds.

Ch2 Press and hold the Ch button

and 2 button at the same time

for 3 seconds.

Ch3 Press and hold the Ch button

and 3 button at the same time

for 3 seconds.

Ch4 Press and hold the Ch button

and 4 button at the same time

for 3 seconds.

Inde-

pendent

Independent Press and hold the

Ch button and 0 button at the

same time for 3 seconds.

125

Setting Various Functions

User’s Manual Settin

Functions from Menus

Selecting a Display Language

[Language]

You can select the language in which the

menus are displayed.

MENU > [System settings] > [Language]

Use the [ ] / [ ] / [ ] / [ ] buttons to

select the menu language, then press the

OK button.

When the setting is completed, press the

OK button to accept your setting and then

press the MENU button or EXIT button

(WX6000 / SX6000).

HDMI Component

Digital PC Analog PC

English

German

French

Italian

Spanish

Portuguese

Swedish

Russian

Dutch

Finnish

Norwegian

Turkish

Polish

Hungarian

Czech

Danish

Arabic

Chinese (Simplified)

Chinese (Traditional)

Korean

Japanese

Setting Various Functions

126

Showing / Hiding the

Guide Screen

[Guide]

You can select whether to show or hide the

guide screen which explains operations.

MENU > [System settings] > [Guide]

MENU > [Install settings] > [On screen] >

[Guide]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [On] is the factory default.

• The guide screen is shown at the following

times.

-Power is turned off by pressing the

POWER button. (P80)

-No input signal can be detected. (P58)

-An invalid button is pressed in the

[BLANK], [FREEZE] or [D.ZOOM]

mode. (P82, P84)

-When the positional lock (P139) is set to

[On] (WX6000 / SX6000)

HDMI Component

Digital PC Analog PC

Off Hides the guide screen.

On Shows the guide screen.

127

Setting Various Functions

User’s Manual Settin

Functions from Menus

Showing / Hiding the

Input Status

[Show Input Status]

You can select whether the signal status is

displayed on the screen when there is no

signal or when making signal settings.

MENU > [System settings] > [Show Input Sta-

tus]

MENU > [Install settings] > [On screen] > [Show

input status]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [On] is the factory default.

Selecting the HDMI Input

[HDMI In]

Set the type of equipment which is con-

nected to the HDMI port.

MENU > [System settings] > [HDMI In]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

HDMI Component

Digital PC Analog PC

Off The input status is not displayed.

On The input status is displayed.

HDMI Component

Digital PC Analog PC

Auto Select when AV equipment will

be connected. Image pro-

cessing, menu displays, and

other elements are adjusted

for video equipment.

Computer Select when a computer will be

connected. Image processing,

menu displays, and other ele-

ments are adjusted for a com-

puter.

Setting Various Functions

128

Setting a Password

[Password settings]

Disables the projector unless the correct

password is entered.

MENU > [System settings] > [Other settings] >

[Password settings]

MENU > [System settings] > [Other settings] >

[Password settings]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [Off] is the factory default.

• You cannot set [On] unless you have com-

pleted [Register password].

Once you set a password, the password

entry screen appears at power-on.

Enter a 4 digit password.

For the WUX5000 / WUX4000, the pass-

word can be entered using the [ ] / [ ] /

[ ] / [ ] buttons. For the WX6000 /

SX6000, the password can be entered

using a combination of the numerical but-

tons and the [ ] / [ ] / [ ] / [ ] buttons.

[ ] / [1], [ ] / [2], [ ] / [3], and [ ] / [4]

have the same function.

If the password is valid, the projection

starts. If you enter a wrong password three

times, the power will be turned off.

• The power is also turned off if no password

is input for 3 minutes.

HDMI Component

Digital PC Analog PC

Off

The projector can be used even if no pass-

word is entered.

The projector cannot be used unless you

enter your password.

To Cancel the Password

Turn off the projector and unplug the power

plug.

Hold down the

button on the side control

and connect the power plug. Make sure to keep

holding down the

button until a beep

sounds. When the beep sounds, the password

is canceled. (The entered password is also

reset.)

To forcibly cancel the password from the remote

control, in standby state press the

button

3 times, then press the

POWER

button.

129

Setting Various Functions

User’s Manual Settin

Functions from Menus

Registering a Password

[Register password]

You can register a password for starting

projection.

MENU > [System settings] > [Other settings] >

[Register password]

MENU > [System settings] > [Other settings] >

[Register password]

Press the OK button after selecting [Reg-

ister password], and the following screen

for registering a password appears.

Enter a 4 digit password.

For the WUX5000 / WUX4000, the pass-

word can be entered using the [ ] / [ ] /

[ ] / [ ] buttons. For the WX6000 /

SX6000, the password can be entered

using a combination of the numerical but-

tons and the [ ] / [ ] / [ ] / [ ] buttons.

[ ] / [1], [ ] / [2], [ ] / [3], and [ ] / [4]

have the same function.

The 4-digit password is entered from the

left to right digits. When the final digit is

entered, the password is automatically

registered.

• Press the MENU button to abort the regis-

tration.

HDMI Component

Digital PC Analog PC

Setting Various Functions

130

Prohibiting Operation of

the Lens

[Lens Ctrl Lock]

You can lock lens-related button opera-

tions.

MENU > [System settings] > [Other settings] >

[Lens Ctrl Lock]

Press the OK button to accept your setting

and then press the MENU button.

• [Off] is the factory default.

HDMI Component

Digital PC Analog PC

Off Focus, zoom, lens shift, and other

lens-related operations are permit-

ted.

On Focus, zoom, lens shift, and other

lens-related operations are locked.

131

Setting Various Functions

User’s Manual Settin

Functions from Menus

Lens Shift Reset

[Lens shift Reset]

Resets the lens shift (P74) setting to the

standard position.

MENU > [System settings] > [Other settings] >

[Lens shift Reset]

MENU > [Install settings] > [Lens shift Reset]

Select [Lens shift Reset] and press the OK

button. The following screen for confirma-

tion appears.

Use the [ ]

[ ] buttons to select the

standard position, and then select OK.

• The standard position varies depending

on the type of lens unit used. For details,

refer to page 75.

• The position which was adjusted by lens

shift does not change when the power is

turned off.

HDMI Component

Digital PC Analog PC

Setting Various Functions

132

Extending the Menu Dis-

play Time

[Menu display time]

The setting for the menu display time can

be extended from the normal 10 or 30 sec-

onds to 3 minutes. For the WUX5000 /

WUX4000, if [Extended] is set, when push-

ing and holding a button on the projector or

remote control, the same key repeat func-

tion will be enabled as when pressing a

button repeatedly.

MENU > [System settings] > [Other settings] >

[Menu display time]

MENU > [Install settings] > [On screen] > [Menu

display time]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [Normal] is the factory default.

• The following display and operation are also

changed.

*1 WUX4000

*2 WX6000 / SX6000

HDMI Component

Digital PC Analog PC

Normal The menu is displayed for 10 or 30 sec-

onds.

Extended The menu is displayed for 3 minutes.

Item [Normal] [Extended]

The display time of the following

screens

-MENU screen

-Input (P60)

-Zoom adjustment (P71)

-Focus adjustment (P73)

-Keystone adjustment (P76)

-Keystone reset (P77)

-D.image shift adjustment (P67, P68)

-D.image shift reset (P69)

-Aspect (P70)

-Image mode (P78)

-Volume adjustment (P83)

-Lamp mode (P119) *1

-Lens shift (P74)

-Lens shift reset (P131)

10 / 30

seconds 3 minutes

Press-and-hold operation of

pointer buttons other than for

[Zoom adjustment], [Focus

adjustment], and [Lens shift]

Press-and-hold operation of

VOL

button

Press-and-hold operation of the

D.ZOOM button

Enabled Disabled

Key repeat *2 [On] [Off]

133

Setting Various Functions

User’s Manual Settin

Functions from Menus

Showing / Hiding the High

Temperature Warning Icon

[Overheat Warning Display]

You can select whether or not to display

the [High temperature warning] icon when

the temperature inside the projector has

increased and is approaching the overheat

temperature.

MENU > [System settings] > [Other settings] >

[Overheat Warning Display]

MENU > [Install settings] > [On screen] > [Over-

heat warning display]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

When [On] is set, the [High temperature

warning] icon shown below will be dis-

played when the temperature inside the

projector is abnormally high.

• [Off] is the factory default.

HDMI Component

Digital PC Analog PC

Off The [High temperature warning] icon is

not displayed.

On The [High temperature warning] icon is

displayed.

Screen

Setting Various Functions

134

Reducing Flickering

[Deflicker]

This function adjusts the image display in

order to reduce flickering in the projected

image.

MENU > [System settings] > [Other settings] >

[Deflicker]

• When deflicker is performed, the image

adjustment screen is projected for approx-

imately 20 seconds.

• To cancel deflicker, press the POWER

button.

Gamma Restore

[Gamma restore]

This function is used when changing and

turning of the tone characteristics and ach-

romatic color is noticed over a long period

of time.

MENU > [System settings] > [Other settings] >

[Gamma restore]

If Gamma restore is performed, the pro-

jected image will be adjusted for a period

of approximately 150 seconds.

• To stop Gamma restore, press the POWER

button or the EXIT button (WX6000 /

SX6000).

HDMI Component

Digital PC Analog PC

Off Deflicker adjustment is not per-

formed.

Adjust Select [Deflicker] to adjust. The fol-

lowing screen appears.

OK Deflicker is performed.

Cancel Deflicker is not performed.

• Deflicker is a function that decreases

flickering. However, there are some

cases that flickering continues.

• Deflicker can only be used when the

lamp has been on for approximately

30 minutes or longer.

HDMI Component

Digital PC Analog PC

Off Returns to the factory default with-

out performing Gamma restore.

Adjust Performs Gamma restore and

applies the result.

OK Gamma Restore is per-

formed.

Cancel Gamma Restore is not

performed.

• If Gamma restore is performed, the

tone characteristics and achromatic

color will be restored as close as

possible to the condition when the

unit was purchased, however it is not

possible to restore it completely to

the original condition. So the chang-

ing and turning color cannot be elim-

inated completely.

• Gamma restore can only be used

when the lamp has been on for

approximately 30 minutes or longer.

135

Setting Various Functions

User’s Manual Settin

Functions from Menus

Lamp Warning Display

[Lamp warning display]

A message that advises you to change the

lamp can be set to display when the lamp

has been used for the specified period of

time.

MENU > [Install settings] > [On screen] > [Lamp

warning display]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• The factory default is [On].

• Regardless of the [Lamp warning display]

setting, when the lamp replacement time has

been reached, the LAMP indicator on the

projector will flash.

Resetting the Lamp

Counter

[Lamp counter]

You can reset the lamp counter that indi-

cates the time for lamp replacement.

MENU > [System settings] > [Other settings] >

[Lamp counter]

MENU > [System settings] > [Other settings] >

[Lamp counter]

HDMI Component

Digital PC Analog PC

Off The lamp warning display is not

displayed.

On The prepare lamp message and

the lamp warning display are dis-

played.

HDMI Component

Digital PC Analog PC

Do not reset the lamp counter except

when you have replaced the lamp.

Otherwise, the lamp counter cannot

indicate the correct timing for replac-

ing the lamp.

For details of lamp replacement, refer

to page 195.

Setting Various Functions

136

Select [Lamp counter] and press the OK

button to display the lamp counter.

Select [Reset] and press the OK button.

Select [OK] on the screen for confirmation

and press the OK button to reset the lamp

counter.

Press the MENU button or EXIT button

(WX6000 / SX6000).

■About the Display of the Lamp

Counter

The lamp counter displays the hours of

use of the lamp in the following way.

Less than 2,700 hours

Displayed as a green bar.

2,700 hours to less than 3,000 hours

Displayed as a green and yellow bar.

When the lamp hours are 2,700 hours to

less than 3,000 hours, the message

“Obtain a new lamp.” appears when

power is turned on.

Over 3,000 hours

Displayed as a green, yellow and red

bar.

The message “Replace with the new

lamp.” appears when power is turned on.

137

Setting Various Functions

User’s Manual Settin

Functions from Menus

Filter Warning Display

[Filter warning display]

A message advising you to perform clean-

ing can be set to display when the filter

needs cleaning.

MENU > [Install settings] > [On screen] > [Filter

warning display]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• The factory default is [On].

Resetting the Air Filter

Counter

[Filter counter]

This resets the counter which reminds you

of the time for cleaning and replacing the

air filter.

MENU > [System settings] > [Other settings] >

[Filter counter]

If the OK button is pressed on [Filter

counter], the air filter counter is displayed.

Select [Reset] and press the OK button.

[OK] is selected on the confirmation

screen and the OK button is pressed, the

air filter counter is reset.

Press the MENU button or EXIT button

(WX6000 / SX6000).

HDMI Component

Digital PC Analog PC

Off The filter warning display is not

displayed.

On The filter warning display is dis-

played.

HDMI Component

Digital PC Analog PC

For details about how to replace or

clean the filter, refer to page 193.

Setting Various Functions

138

Displaying Test Pattern

[Test pattern]

A test pattern for checking the resolution

and color when installing the projector can

be displayed.

MENU > [Install settings] > [Test pattern]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• The factory default is [Off].

• While the test pattern is displayed, you can

use the [] / [] buttons to change to a dif-

ferent test pattern. Also, if a test pattern has

option settings, you can change the settings

using the [] / [] button. (P217)

• The test pattern can also be displayed or

turned off by pressing the TEST PATTERN

button on the remote control.

HDMI Component

Digital PC Analog PC

Off The test pattern is not displayed.

On The test pattern is displayed.

The following functions in the [Image

adjustment] tab are not applied to the

test pattern.

• Brightness adjustment function

(P111)

• Contrast adjustment function (P112)

• Sharpness adjustment function

(P113)

• Color level adjustment function

(P114)

• Color balance adjustment function

(P114)

139

Setting Various Functions

User’s Manual Settin

Functions from Menus

Selecting Audio In Termi-

nal

[Audio in terminal select]

You can select the audio in terminal that is

used for each input signal (HDMI, Digital

PC, Analog PC-1, Analog PC-2, Compo-

nent).

MENU > [Install settings] > [Audio in terminal

select]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• The factory default is as follows.

HDMI: HDMI

Digital PC: Audio in 2

Analog PC-1: Audio in 1

Analog PC-2: Audio in 2

Component: Audio in 1

Locking Installation

Related Functions

[Positional lock]

Operation of installation related functions

can be prohibited.

MENU > [Install settings] > [Positional lock]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• The factory default is [Off].

• The positional lock can be applied to Test

pattern display, Screen aspect settings, Key-

stone adjustment, Digital image shift adjust-

ment, Image flip H/V, Focus adjustment,

Zoom adjustment, Lens shift adjustment and

Lens shift reset.

HDMI Component

Digital PC Analog PC

Off No audio is output.

Audio in 1 Outputs the audio signal that

is inputted in Audio in terminal

Audio in 2 Outputs the audio signal that

is inputted in Audio in terminal

HDMI Outputs the HDMI audio sig-

nal. (Only for HDMI)

HDMI Component

Digital PC Analog PC

Off The positional lock is not used.

On Installation related functions can-

not be used.

Setting Various Functions

140

Resetting to the Default Setting

[Factory defaults]

You can reset the menu item settings and

restore the system settings to the factory

defaults.

MENU > [System settings] > [Other settings] >

[Factory defaults]

MENU > [System settings] > [Other settings] >

[Factory defaults]

Select [Factory defaults] and press the OK

button. The following screen for confirma-

tion appears.

• This function does not reset the values for

[Lamp counter], [Language], [Remote con-

trol], [Input signal], [Network Setting], [Filter

counter], [Focus position], [Zoom position],

and [Lens shift position].

• For factory defaults settings, refer to pages

232 – 238.

• The contents of the user memory return to the

conditions at the time it was saved. (P110)

HDMI Component

Digital PC Analog PC

OK Settings are reset to default.

Cancel Settings are not reset to default.

141

User’s Manual Settin

Functions from Menus

Checking Projector Information

[Information]

You can check information about the

signal types of the images projected and other

information.

Information shown

* Not displayed when network functions are [Off].

HDMI Component

Digital PC Analog PC

Item Meaning

Model name WUX5000 / WUX4000 / WX6000 / SX6000

Input signal Details of the input signal currently selected

Information such as the signal type, signal resolution, and frequency

is displayed.

Firmware Current firmware version

Serial No. Serial number unique to this projector

IP address* IP address of the projector (P175)

Gateway address* IP address of the gateway device (P175)

E-mail sender address* Sender e-mail address used for sending error mails (P183)

E-mail recipient

address*

Displays [Already set] or [Not set] to show whether a recipient e-mail

address has been set for receiving error mails. (P183)

Projector name* Name which identifies this projector on the network

Location* Location where the projector is installed

System information ID System information. Normally this is not displayed.

MENU > [Information] MENU > [Information]

142

143

MULTIMEDIA PROJECTOR

Installation Manual

(Installation and

Maintenance)

Do not attempt installation yourself. Be sure to

request installation from a qualified technician or

contact the Canon Customer Support Center.

144

Projecting an Image

Safety Instructions

Before Use

Table of Contents

Useful Functions Available

During a Presentation

Setting Functions from Menus

Installation

Connecting to a Network

Maintenance

Index

Appendix

User’s Manual

Installation Manual

Appendix

145

Installation

146

Installation Precautions

Precautions When Carrying the Projector

Installation Precautions

Be sure to read on page 12 – 24. Pay attention to the following when installing the

projector.

Precautions When Carrying and Transporting the Pro-

jector

Prepare the projector as described below before carrying it.

• Disconnect the cables connected to the projector. Carrying

the projector with the cables attached may cause an acci-

dent.

• Retract the adjustable feet.

• When the projector is transported after the lens unit is

installed, be sure that you do not grasp the lens while trans-

porting it. Doing so may damage the projector.

• Do not strike the projector or

subject it to impact. Doing so

may cause a malfunction.

• Do not install the projector so

that it is inclined or standing

vertically. The projector may tip

over, causing damage.

• Do not block the cooling fan

intake or exhaust vent. If the intake or exhaust vent is

blocked, heat may accumulate inside the projector, causing

a malfunction.

• Do not reuse any packaging or shock-absorbent materials

that were supplied with the projector at the time of purchase

for transporting or shipping the projector. Protection of the

projector cannot be guaranteed if used packaging or shock-

absorbent materials are reused. Fragments from shock-

absorbent material may also enter the interior of the projec-

tor which could cause a malfunction.

• If transportation is necessary, the lens unit should be

removed before transporting the projector. If the projector is

subjected to excessive impacts during transportation, the

lens unit may be damaged. Removal and installation of the

lens unit should not be performed by the user. Be sure to

have the procedure performed by a qualified technician or

contact the Canon Customer Support Center.

Exhaust

Intake

147

Installation Precautions

Installation Manual Installation

■Do Not Use in the Following Environments

• Do not install the projector in a humid or dusty location or a position where there is a lot

of oily smoke or cigarette smoke. Optical parts such as the lens and mirror may be

stained, resulting in poor picture quality.

• Do not install close to high-voltage power lines or power sources. The projector may not

operate correctly.

• Do not use the projector on a soft surface such as a carpet or sponge mat. Heat may

accumulate inside the projector, causing a malfunction.

• Do not use the projector in a location that is subject to very high temperatures, very low

temperatures, or high levels of humidity. Doing so may cause a malfunction. The tem-

perature and humidity ranges for operation and the temperature range for storage are

shown below.

■Do Not Touch the Lens with Bare Hands

Do not touch the lens with bare hands. Doing so may adversely affect picture quality.

■Install at a Sufficient Distance from Walls and Other Obstructions

■Be Careful of Condensation

If the temperature of the room rises suddenly, moisture in the air may condense on the

projector lens and mirror, causing the image to become blurred. Wait until condensation

evaporates and a normal picture is shown.

■When Using the Projector at Altitudes Greater than 2,300 m

Contact the Canon Customer Support Center if you intend to use this projector at altitudes

of 2,300 m or higher.

Operating

temperature

Operating

humidity

Storage

temperature

5°C to 35°C Up to 85% -10°C to 60°C

If the air intake or

exhaust vent is blocked,

heat will accumulate

inside the projector,

possibly resulting in a

shortened projector life-

time or a malfunction.

Do not install in a

closet, on a bookshelf,

or other narrow location

with poor ventilation.

Install in a well venti-

lated location. (Install

with a minimum of 50

cm (1.6') clearance on

the top and sides, and

50 cm (1.6') to the rear.)

50 cm

(1.6')

Exhaust vent

Air intake vent

Warmed airflow

50 cm

(1.6') 50 cm

(1.6')

Installation Precautions

148

■When using mounted on the ceiling

■Install facing in the correct direction

When the projector is used mounted on the

ceiling or installed in a high location, it is nec-

essary to periodically clean the air intake and

exhaust vents, and the area around the air fil-

ter. If dust accumulates in the intake or

exhaust vents, cooling performance will dete-

riorate, causing the internal temperature to rise and possibly resulting in a

malfunction or fire. Use a vacuum cleaner or similar means to remove dust

from the intake vent and exhaust vent.

10°

10°10°

This projector can be installed in directions of 360° *1 as shown in the

illustration below. However, if projecting upward or downward , the

life span of the lamp may be shortened, and it is necessary to change the

settings of the projector. If using the projector for upward or downward

projection, please contact the Canon Customer Support Center.

*1 There are no options for installing the projector other than the ceiling attachment. (P33, P150, P231)

*2 This may damage the lamp.

Downward projec-

tion:

Inclination of the

projector should be

no more than 10°

from the vertical

axis. *2

Upward projection:

Inclination of the

projector should be

no more than 10°

from the vertical

axis. *2

If installing the projec-

tor on the floor or

hanging from the ceil-

ing, the left / right incli-

nation of the projector

should be no more

than 10°. *2

Do not use the projector

standing on its side. *2

149

Installation Manual Installation

Installation Procedure

Selecting the Projection Method and

Installation Location (P150)

Installing / Removing the Lens Unit (P151)

Setting Up the Projector (P156)

Connecting to AV Equipment (P162)

Selecting an Input Signal (P59)

Adjusting the Image (P61)

Connecting to a Network (P165)

150

Selecting the Projection Method and Installation Location

■Ceiling Mounting or Rear Projection

You can mount the projector on the ceiling (ceiling mounting) with it turned upside down

or place it behind the screen (rear projection) if you use a translucent screen.

Make sure to use the optional ceiling attachment. For the ceiling attachment, refer to

page 231.

■Adjusting the projection position when installed on the floor

To adjust the projection position when the projector is installed on the floor, use the lens

shift function (P74 and P160) to adjust up / down / left / right. You can also use the adjust-

able feet to incline the projector upward by up to 6°. For information about the relationship

between screen size and projection distance, refer to page 156.

When the projector is inclined upwards, the projected image will be distorted into a trape-

zoid shape. This can be corrected by using the keystone correction. (P76)

Ceiling Mounting Rear Projection

Adjust-

able feet

Lens shift

151

Installation Manual Installation

Installing / Removing the Lens Unit

■Installing the Lens Unit

1Use a Phillips-head screwdriver and loosen the lamp cover screw, then open the lamp

cover.

The lamp cover screw is attached to the lamp cover and designed to prevent it from

falling off.

Before installing or removing the lens unit, be sure to disconnect

the power plug or connector. Failure to do so may result in fire,

electric shock, or injury.

• Before replacing the lens unit, make sure to turn off the pro-

jector, wait at least 1 hour to allow the projector to cool thor-

oughly. Failure to do so may result in burns or other injuries.

• Do not touch the lens when the lens is moving (the lens is

shifting) to adjust the projected image after installation. There

is the risk of injury.

• When hanging the projector from a ceiling, put the projector

down on the floor or a workbench before attaching or replac-

ing the lens unit. Failure to do so could result in parts falling

off the projector and may cause an accident or personal

injury.

• Do not attempt to install or remove the lens unit yourself. Be

sure to request this service from a qualified technician or con-

tact the Canon Customer Support Center.

• When installing and removing the lens unit, be sure not to

touch the surface of the lens with your hands or scratch it.

• Do not apply force to parts (e.g. lead wires) that are connected

to the lens unit or lens motor. Doing so may cause a malfunc-

tion.

• Do not replace the lens unit in a dusty location. If any dust or

dirt enters the projector, this may adversely affect picture

quality.

• For details about which devices the projector is compatible

with, contact the Canon Customer Support Center.

Screw

Installing / Removing the Lens Unit

152

2Loosen the cosmetic panel screw, then slide the cosmetic panel toward the rear to

remove it.

The cosmetic panel screw is attached to the cosmetic panel and designed to prevent

it from falling off.

3In order to prevent damage, close the lamp cover and temporarily fasten the screw.

4Remove the sleeve screws (2 on top and 2 on bottom).

After the 2 screws on top are removed, turn the projector upside down on a flat desk

or similar location and remove the 2 screws from the bottom.

153

Installing / Removing the Lens Unit

Installation Manual Installation

5Then turn the projector back over and remove the sleeve.

6Referring to the following illustration, insert the lens connector of the lens unit into the

front right side of the projector slowly until it contacts the end. At this time, pull out the

lens cable shown in the illustration and fix it.

7Tighten the 4 screws to fasten the lens unit in place.

The 4 lens unit screws are attached to the lens unit and cannot be removed.

Lens connector

Lens cable

Installing / Removing the Lens Unit

154

8Insert the projector lens cable into the connector until a click sound is heard.

9Reinstall the sleeve, cosmetic panel, and lamp cover in their original positions.

When the power is first turned on after the lens unit has been installed or replaced, lens shift

initialization operation will be performed. It will take approximately 1 minute for the initializa-

tion operation to start up. However, if the lens has been replaced with a lens of the same

model number, initialization operation will not be performed. The position will be the same as

before the lens was replaced.

The lens shift initialization operation uses the motor to move

the lens up / down / left / right. Do not touch the lens. Doing so

could result in an injury.

When installing and removing the lens unit, be sure to fix the

lens cable as shown in the illustration. When inserting the lens

unit, it is possible to damage the lens cable between the lens

unit and projector.

155

Installing / Removing the Lens Unit

Installation Manual Installation

■Removing the Lens Unit

1Perform steps 1 to 5 on pages 151 – 153 and remove the sleeve.

2Disconnect the lens cable from the lens connector.

3Fix the lens cable as shown in the illustration and loosen the 4 screws to remove the

lens unit.

The 4 lens unit screws are attached to the lens unit and cannot be removed.

When pulling out (disconnecting) the lens cable, press the buttons on both sides of the lens

cable connector while pulling out the cable.

156

Setting Up the Projector

■Positioning the Projector in Front of the Screen

Place the projector in front of the screen.

■Relationship Between Image Size and Projecting Distance

The projected image size is determined by the distance between the projector and the

screen (projection distance) as well as the zoom. Refer to the following table and decide

the distance between the projector and screen.

• Be sure to place the projector parallel

to the screen to ensure distortion-free

projection.

• The screen must not be exposed to

direct sunlight or light from lighting

equipment. In a bright room, it is rec-

ommended that lights be turned off,

curtains be drawn, and other steps

taken to make the screen easier to see.

• H1 and H2 are the distances when lens shift is the default value below.

• Standard Zoom Lens / Long Zoom Lens / Ultra Long Zoom Lens:

+50% (up / down), 0% (left / right)

Short Fixed Lens: 0% (up / down / left / right)

Optical axis

Screen

16:9/16:10

Optical axis when pro-

jection is perpendicu-

lar to screen

Screen

Height Height

WidthWidth

16:9 / 16:10

Screen size

(diagonal) 4:3

157

Setting Up the Projector

Installation Manual Installation

WUX5000 / WUX4000

Lens unit Diagonal

when

16:10

Image size (cm) Projection distance

m (feet)

Distance from optical

axis when projection is

perpendicular to

screen* (cm)

16:10 16:9 4:3 16:10

Width Height Width Height Width Height Wide limit Tele limit H1 H2

Standard

Zoom Lens

RS-IL01ST

40 86 54 86 48 72 54 1.3 (4.3) 1.9 (6.2) 54 0

60 129 81 129 73 108 81 1.9 (6.2) 2.9 (9.5) 81 0

80 172 108 172 97 144 108 2.6 (8.5) 3.9 (12.8) 108 0

100 215 135 215 121 179 135 3.2 (10.5) 4.8 (15.7) 135 0

150 323 202 323 182 269 202 4.8 (15.7) 7.2 (23.6) 202 0

200 431 269 431 242 359 269 6.4 (21.0) 9.6 (31.5) 269 0

250 538 337 538 303 449 337 8.0 (26.2) 12.1 (39.7) 337 0

300 646 404 646 363 538 404 9.6 (31.5) 14.5 (47.6) 404 0

350 754 471 754 424 628 471 11.3 (37.1) 16.9 (55.4) 471 0

400 862 538 862 484 718 538 12.9 (42.3) 19.3 (63.3) 538 0

450 969 606 969 544 808 606 14.5 (47.6) 21.7 (71.2) 606 0

500 1077 673 1077 605 898 673 16.1 (52.8) 24.1 (79.1) 673 0

550 1185 740 1185 666 987 740 17.7 (58.1) 26.6 (87.3) 740 0

600 1292 808 1292 726 1076 808 19.3 (63.3) 29.0 (95.1) 808 0

Long Zoom

Lens

RS-IL02LZ

40 86 54 86 48 72 54 1.9 (6.2) 3.2 (10.5) 54 0

60 129 81 129 73 108 81 2.8 (9.2) 4.8 (15.7) 81 0

80 172 108 172 97 144 108 3.8 (12.5) 6.4 (21.0) 108 0

100 215 135 215 121 179 135 4.7 (15.4) 8.0 (26.2) 135 0

150 323 202 323 182 269 202 7.1 (23.3) 12.1 (39.7) 202 0

200 431 269 431 242 359 269 9.5 (31.2) 16.1 (52.8) 269 0

250 538 337 538 303 449 337 11.9 (39.0) 20.2 (66.3) 337 0

300 646 404 646 363 538 404 14.2 (46.6) 24.2 (79.4) 404 0

350 754 471 754 424 628 471 16.6 (54.5) 28.3 (92.8) 471 0

400 862 538 862 484 718 538 19.0 (62.3) 32.3 (106.0) 538 0

450 969 606 969 544 808 606 20.9 (68.6) 35.6 (116.8) 606 0

500 1077 673 1077 605 898 673 23.8 (78.1) 40.4 (132.5) 673 0

550 1185 740 1185 666 987 740 26.1 (85.6) 44.5 (146.0) 740 0

600 1292 808 1292 726 1076 808 28.5 (93.5) 48.5 (159.1) 808 0

Short Fixed

Lens

RS-IL03WF

40 86 54 86 48 72 54 0.7 (2.3) 27 27

60 129 81 129 73 108 81 1.0 (3.3) 41 41

80 172 108 172 97 144 108 1.4 (4.6) 54 54

100 215 135 215 121 179 135 1.7 (5.6) 68 68

150 323 202 323 182 269 202 2.6 (8.5) 101 101

200 431 269 431 242 359 269 3.4 (11.2) 135 135

250 538 337 538 303 449 337 4.3 (14.1) 168 168

300 646 404 646 363 538 404 5.2 (17.1) 202 202

Ultra long

Zoom Lens

RS-IL04UL

40 86 54 86 48 72 54 – – 54 0

60 129 81 129 73 108 81 4.6 (15.1) 9.0 (29.5) 81 0

80 172 108 172 97 144 108 6.1 (20.0) 12.0 (39.4) 108 0

100 215 135 215 121 179 135 7.6 (24.9) 14.9 (50.2) 135 0

150 323 202 323 182 269 202 11.4 (37.4) 22.3 (77.3) 202 0

200 431 269 431 242 359 269 15.2 (49.7) 29.8 (97.8) 269 0

250 538 337 538 303 449 337 18.9 (62.0) 37.2 (122.0) 337 0

300 646 404 646 363 538 404 22.7 (74.5) 44.6 (146.3) 404 0

350 754 471 754 424 628 471 26.4 (86.6) 52.0 (170.6) 471 0

400 862 538 862 484 718 538 30.2 (99.1) 59.4 (194.9) 538 0

450 969 606 969 544 808 606 34.0 (111.5) 66.8 (219.2) 606 0

500 1077 673 1077 605 898 673 37.7 (123.7) 74.2 (243.4) 673 0

550 1185 740 1185 666 987 740 41.5 (136.2) 81.6 (267.7) 740 0

600 1292 808 1292 726 1076 808 45.2 (148.3) 89.0 (292.0) 808 0

Setting Up the Projector

158

WX6000

Lens unit Diagonal

when

16:10

Image size (cm) Projection distance

m (feet)

Distance from optical

axis when projection is

perpendicular to

screen* (cm)

16:10 16:9 4:3 16:10

Width Height Width Height Width Height Wide limit Tele limit H1 H2

Standard

Zoom Lens

RS-IL01ST

40 86 54 86 48 72 54 1.3 (4.3) 2.0 (6.6) 54 0

60 129 81 129 73 108 81 2.0 (6.6) 3.0 (9.8) 81 0

80 172 108 172 97 144 108 2.6 (8.5) 4.0 (13.1) 108 0

100 215 135 215 121 179 135 3.3 (10.8) 4.9 (16.1) 135 0

150 323 202 323 182 269 202 4.9 (16.1) 7.4 (24.3) 202 0

200 431 269 431 242 359 269 6.6 (21.6) 9.9 (32.5) 269 0

250 538 337 538 303 449 337 8.2 (26.9) 12.4 (40.7) 337 0

300 646 404 646 363 538 404 9.9 (32.5) 14.9 (48.9) 404 0

350 754 471 754 424 628 471 11.5 (37.7) 17.3 (56.8) 471 0

400 862 538 862 484 718 538 13.2 (43.3) 19.8 (65.0) 538 0

450 969 606 969 544 808 606 14.9 (48.9) 22.3 (73.2) 606 0

500 1077 673 1077 605 898 673 16.5 (54.1) 24.8 (81.4) 673 0

550 1185 740 1185 666 987 740 18.2 (59.7) 27.2 (89.2) 740 0

600 1292 808 1292 726 1076 808 19.8 (65.0) 29.7 (97.4) 808 0

Long Zoom

Lens

RS-IL02LZ

40 86 54 86 48 72 54 1.9 (6.2) 3.3 (10.8) 54 0

60 129 81 129 73 108 81 2.9 (9.5) 4.9 (16.1) 81 0

80 172 108 172 97 144 108 3.9 (12.8) 6.6 (21.6) 108 0

100 215 135 215 121 179 135 4.8 (15.7) 8.3 (27.2) 135 0

150 323 202 323 182 269 202 7.3 (23.9) 12.4 (40.7) 202 0

200 431 269 431 242 359 269 9.7 (31.8) 16.6 (54.5) 269 0

250 538 337 538 303 449 337 12.2 (40.0) 20.7 (67.9) 337 0

300 646 404 646 363 538 404 14.6 (47.9) 24.9 (81.7) 404 0

350 754 471 754 424 628 471 17.1 (56.1) 29.0 (95.1) 471 0

400 862 538 862 484 718 538 19.5 (64.0) 33.1 (108.6) 538 0

450 969 606 969 544 808 606 21.9 (71.8) 37.3 (122.4) 606 0

500 1077 673 1077 605 898 673 24.4 (80.1) 41.4 (135.8) 673 0

550 1185 740 1185 666 987 740 26.8 (87.9) 45.6 (149.6) 740 0

600 1292 808 1292 726 1076 808 29.3 (96.1) 49.7 (163.1) 808 0

Short Fixed

Lens

RS-IL03WF

40 86 54 86 48 72 54 0.7 (2.3) 27 27

60 129 81 129 73 108 81 1.1 (3.6) 41 41

80 172 108 172 97 144 108 1.4 (4.6) 54 54

100 215 135 215 121 179 135 1.8 (5.9) 68 68

150 323 202 323 182 269 202 2.7 (8.9) 101 101

200 431 269 431 242 359 269 3.5 (11.5) 135 135

250 538 337 538 303 449 337 4.4 (14.4) 168 168

300 646 404 646 363 538 404 5.3 (17.4) 202 202

Ultra long

Zoom Lens

RS-IL04UL

40 86 54 86 48 72 54 – – 54 0

60 129 81 129 73 108 81 4.8 (15.7) 9.2 (30.2) 81 0

80 172 108 172 97 144 108 6.3 (20.7) 12.3 (40.4) 108 0

100 215 135 215 121 179 135

7.8 (25.6)

15.3 (50.2) 135 0

150 323 202 323 182 269 202 11.7 (38.4) 22.9 (75.1) 202 0

200 431 269 431 242 359 269 15.6 (51.2) 30.5 (100.1) 269 0

250 538 337 538 303 449 337 19.4 (63.6) 38.1 (125.0) 337 0

300 646 404 646 363 538 404 23.3 (76.4) 45.7 (149.9) 404 0

350 754 471 754 424 628 471 27.1 (88.9) 53.3 (174.9) 471 0

400 862 538 862 484 718 538 31.0 (101.7) 60.9 (199.8) 538 0

450 969 606 969 544 808 606 34.8 (114.2) 68.5 (224.7) 606 0

500 1077 673 1077 605 898 673 38.7 (127.0) 76.1 (249.7) 673 0

550 1185 740 1185 666 987 740 42.5 (139.4) 83.7 (274.6) 740 0

600 1292 808 1292 726 1076 808 46.4 (152.2) 91.3 (299.5) 808 0

159

Setting Up the Projector

Installation Manual Installation

SX6000

Lens unit Diagonal

when 4:3 Image size (cm) Projection distance

m (feet)

Distance from optical

axis when projection is

perpendicular to

screen* (cm)

4:3 16:10 16:9 4:3

Width Height Width Height Width Height Wide limit Tele limit H1 H2

Standard

Zoom Lens

RS-IL01ST

40 81 61 81 51 81 46 1.3 (4.3) 1.9 (6.2) 61 0

60 122 91 122 76 122 69 1.9 (6.2) 2.9 (9.5) 91 0

80 163 122 163 102 163 91 2.5 (8.2) 3.8 (12.5) 122 0

100 203 152 203 127 203 114 3.2 (10.5) 4.8 (15.7) 152 0

150 305 229 305 191 305 171 4.8 (15.7) 7.2 (23.6) 229 0

200 406 305 406 254 406 229 6.4 (21.0) 9.6 (31.5) 305 0

250 508 381 508 318 508 286 8.0 (26.2) 12.0 (39.4) 381 0

300 610 457 610 381 610 343 9.6 (31.5) 14.4 (47.2) 457 0

350 711 533 711 445 711 400 11.2 (36.7) 16.8 (55.1) 533 0

400 813 610 813 508 813 457 12.8 (42.0) 19.2 (63.0) 610 0

450 914 686 914 572 914 514 14.4 (47.2) 21.6 (70.9) 686 0

500 1016 762 1016 635 1016 572 16.0 (52.5) 24.0 (78.7) 762 0

550 1118 838 1118 699 1118 629 17.6 (57.7) 26.4 (86.6) 838 0

600 1219 914 1219 762 1219 686 19.2 (63.0) 28.8 (94.5) 914 0

Long Zoom

Lens

RS-IL02LZ

40 81 61 81 51 81 46 1.9 (6.2) 3.2 (10.5) 61 0

60 122 91 122 76 122 69 2.8 (9.2) 4.8 (15.7) 91 0

80 163 122 163 102 163 91 3.7 (12.1) 6.4 (21.0) 122 0

100 203 152 203 127 203 114 4.7 (15.4) 8.0 (26.2) 152 0

150 305 229 305 191 305 171 7.1 (23.3) 12.0 (39.4) 229 0

200 406 305 406 254 406 229 9.4 (30.8) 16.1 (52.8) 305 0

250 508 381 508 318 508 286 11.8 (38.7) 20.1 (65.9) 381 0

300 610 457 610 381 610 343 14.2 (46.6) 24.1 (79.6) 457 0

350 711 533 711 445 711 400 16.5 (54.1) 28.1 (92.2) 533 0

400 813 610 813 508 813 457 18.9 (62.0) 32.2 (105.6) 610 0

450 914 686 914 572 914 514 21.3 (69.9) 36.2 (118.8) 686 0

500 1016 762 1016 635 1016 572 23.7 (77.8) 40.2 (131.9) 762 0

550 1118 838 1118 699 1118 629 26.0 (85.3) 44.2 (145.0) 838 0

600 1219 914 1219 762 1219 686 28.4 (93.2) 48.3 (158.5) 914 0

Short Fixed

Lens

RS-IL03WF

40 81 61 81 51 81 46 0.7 (2.3) 30 30

60 122 91 122 76 122 69 1.0 (3.3) 46 46

80 163 122 163 102 163 91 1.4 (4.6) 61 61

100 203 152 203 127 203 114 1.7 (5.6) 76 76

150 305 229 305 191 305 171 2.6 (8.5) 114 114

200 406 305 406 254 406 229 3.4 (11.2) 152 152

250 508 381 508 318 508 286 4.3 (14.1) 191 191

300 610 457 610 381 610 343 5.1 (16.7) 229 229

Ultra long

Zoom Lens

RS-IL04UL

40 81 61 81 51 81 46 – – 61 0

60 122 91 122 76 122 69 4.6 (15.1) 9.0 (29.5) 91 0

80 163 122 163 102 163 91 6.1 (20.0) 11.9 (39.0) 122 0

100 203 152 203 127 203 114 7.6 (24.9) 14.9 (48.9) 152 0

150 305 229 305 191 305 171 11.3 (37.1) 22.2 (72.8) 229 0

200 406 305 406 254 406 229 15.1 (49.5) 29.6 (97.1) 305 0

250 508 381 508 318 508 286 18.8 (61.7) 37.0 (121.4) 381 0

300 610 457 610 381 610 343 22.6 (74.1) 44.4 (145.7) 457 0

350 711 533 711 445 711 400 26.3 (86.3) 51.7 (169.6) 533 0

400 813 610 813 508 813 457 30.0 (98.4) 59.1 (193.9) 610 0

450 914 686 914 572 914 514 33.8 (110.9) 66.5 (218.2) 686 0

500 1016 762 1016 635 1016 572 37.5 (123.0) 73.8 (242.1) 762 0

550 1118 838 1118 669 1118 629 41.3 (135.5) 81.2 (266.4) 838 0

600 1219 914 1219 762 1219 686 45.0 (147.6) 88.6 (290.7) 914 0

Setting Up the Projector

160

■Lens Shift Function

The projector includes a lens shift function. Operation of the buttons slides the lens up,

down, left, and right, moving the image position. For the function operations, refer to page

74.

The amount of lens shift is indicated as a percentage relative to the image height and

width.

The table below shows the lens shift for each lens.

WUX5000 WUX4000 WX6000 SX6000

Standard

Zoom Lens

(RS-IL01ST)

Up (1) +55% +55% +55% +50%

Down (2) -15% -15% -15% -12%

Left/right (3) ±10% ±10% ±10% ±10%

Long Zoom

Lens

(RS-IL02LZ)

Up (1) +55% +55% +55% +50%

Down (2) -15% -15% -15% -12%

Left/right (3) ±10% ±10% ±10% ±10%

Short Fixed

Lens

(RS-IL03WF)

Up (1) +5% +5% +5% +5%

Down (2) -5% -5% -5% -5%

Left/right (3) ±2% ±2% ±2% ±2%

Ultra Long

Zoom Lens

(RS-IL04UL)

Up (1) +55% +55% +55% +50%

Down (2) -15% -15% -15% -12%

Left/right (3) ±10% ±10% ±10% ±10%

90°

At maximum downward lens shift

90°

At maximum upward lens shift

(1)

(2)

Amount movable in up/down

direction

161

Setting Up the Projector

Installation Manual Installation

Area where lens movement is not possible

With the Standard Zoom Lens, Long Zoom Lens and Ultra Long Zoom Lens, when the

shift exceeds 44% in the upward direction, the amount of available shift in the left / right

directions decreases. When the lens is shifted upward to the maximum (1), the amount of

available shift in the left / right direction is ±2%.

With the Short Fixed Lens, greater shift in the up / down direction reduces the available

shift in the left / right direction. When the lens is shifted upward or downward to the maxi-

mum, shift in the left / right direction is not possible.

90°

At maximum rightward lens shift

90°

At maximum leftward lens shift

(3)

Amount movable in

left/right direction

2% of projected

image width

2% of projected

image width

44% of projected

image height

(1) Shift range

Projected

image

Area where

shift is not

possible

2% of projected

image width

2% of projected

image width

Area where shift

is not possible

Shift range

Projected

image

5% of

project-

ed image

height

5% of

project-

ed image

height

162

Connecting to AV Equipment

■Connectable Equipment and Input Terminals

Computer (P49)AV equipment (P52)

Digital video camera* (P52)

Computer (P47, P49)

AV equipment (P53)

(P166)

(P47, P49,

P53)

(P50)

(P51, P55)

Computer (P51)

* Select play-

back mode be-

fore connecting.

Analog PC / Component Digital PC

ANALOG PC / COMPO-

NENT IN terminal DVI-D IN terminal HDMI IN terminal

LAN terminal Service port (not

normally used) AUDIO IN terminal AUDIO OUT terminal

Network Audio signal for each

image input

Analog PC /

Component

Digital PC

Amplified speakers

HDMI

HDMI Use this name to select the image input. Direction of signal and data flow

HDMI IN

terminal

The name of the terminal to which to

connect equipment. (Pxxx): indicates the page(s) to refer to.

AV equipment (P53)

163

Connecting to AV Equipment

Installation Manual Installation

Computer (P49)AV equipment (P52)

Digital video camera* (P52)

Computer (P48, P49)

AV equipment(P54)

(P166)

(P48, P49,

P54)

(P50)

(

P51

P55

)

Computer

(P51)

(P30)

Analog PC-1

Component

Analog PC-2

Digital PC HDMI

ANALOG PC-1 / COM-

PONENT IN terminal

ANALOG PC-2 / DVI-D IN

terminal HDMI IN terminal

DVI-I IN terminal can only

be used to connect to a

PC.

* Select play-

back mode be-

fore connecting.

LAN terminal Remote terminal AUDIO IN terminal AUDIO OUT terminal

Network Audio signal for each

image input

Analog

PC-1, 2 /

Component

Digital PC

Amplified speakers

Service terminal (not normally used)

Remote control

(RC-RC05)

Connecting to AV Equipment

164

■Connection Terminal and Connection Cable

Input

signal

Supported

projectors Input terminal Types of connection cables

HDMI

WUX5000

WUX4000

WX6000

SX6000

HDMI cable (not included)

Digital

WUX5000

WUX4000

DVI cable (not included)

WX6000

SX6000



Analog

PC-1

WUX5000

WUX4000

WX6000

SX6000

COMPONENT IN

VGA cable (supplied)

WUX5000

WUX4000

WX6000

SX6000

COMPONENT IN

BNC cable (not included)

Analog

PC-2

WX6000

SX6000

VGA-DVI cable (not included)

Compo-

nent

WUX5000

WUX4000

WX6000

SX6000

COMPONENT IN

Component cable (not included)

BNC cable

(not included)

Mini D-sub 15-pin - BNC

terminal converter cable

(not included)

D terminal plug - RCA plug

component conversion ca-

ble (not included)

RCA plug - RCA plug com-

ponent cable (not included)

Safety Instructions

Table of Contents

Connecting to a Network

Maintenance

Before Use

Projecting an Image

Useful Functions Available

During a Presentation

Setting Functions from Menus

Installation

User’s Manual

Appendix

Index

AppendixInstallation Manual

165

Connecting to a

Network

166

Preparing the Remote Control

If the projector is connected to a network, projector error notification mails can be

received and the projector can be controlled via a computer. Settings related to the net-

work connection can be made from either the projector side (P172) or computer side

(P177).

Depending on the method of network connection, preparation on the computer side may

be necessary. The following is an explanation of preparation on the computer side.

Connection Methods

Connect the projector to the computer via LAN.

• When the [Network function] setting of the projector is set to [Off] (Network Connections

is disabled), switch it to [On] to enable it (P172).

• Referring to page 141, check that the projector IP address does not overlap with other

computers that are on the same LAN. When you set the IP address of the projector, fol-

low the instruction on page 177 on the web screen or refer to page 175.

• When you connect the computer to the network for the first time, it is also necessary to

perform settings on the computer. In this case, consult the network administrator

regarding the necessary settings.

In a network environment where a DHCP server is operating, choose [On] on the projector [DHCP]

screen to enable the DHCP function and connect it (P175).

LAN cable (not included)

(crossover or straight cable) Hub or router, etc.Projector

167

Preparing the Remote Control

Installation Manual Connecting to a Networ

Setting an IP Address

Following is an explanation of how to set the PC IP address for each operating system.

■Windows 7

1From the PC [Start] menu, select [Control Panel].

2Click on [Network and Internet Connections], then click on [View network status and

tasks].

3From the menu on the left side of the window, click on [Change adapter settings].

4Right-click [Local Area Connection], and open [Properties].

5Select [Internet Protocol Version 4 (TCP/IP)] and click the [Properties] button. Make a

note of the original network settings (IP address, subnet mask, default gateway, etc).

6Select [Use the following IP address] and set the IP address and subnet mask.

The factory default IP address for the projector is “192.168.254.254”. Set an IP

address which is different from this.

Example

IP address:192.168.254.1

Subnet mask: 255.255.255.0

7When the settings are completed, click the [OK] button and then click the [OK] button

on the [Local Area Connection Properties] window to close it.

Preparing the Remote Control

168

■Windows Vista

1From the PC [Start] menu, select [Control Panel].

2Click on [View network status and tasks].

3From the menu on the left side of the window, click on [Manage network connections].

4Right-click [Local Area Connection], and open [Properties].

5Select [Internet Protocol Version 4 (TCP/IP)] and click the [Properties] button. Make a

note of the original network settings (IP address, subnet mask, default gateway, etc).

6Select [Use the following IP address] and set the IP address and subnet mask.

The factory default IP address for the projector is “192.168.254.254”. Set an IP

address which is different from this.

Example

IP address:192.168.254.1

Subnet mask: 255.255.255.0

7When the settings are completed, click the [OK] button and then click the [OK] button

on the [Local Area Connection Properties] window to close it.

169

Preparing the Remote Control

Installation Manual Connecting to a Networ

■Windows XP

1From the PC [Start] menu, select [Control Panel].

2Select [Network and Internet Connections] and open [Network Connections].

3Right-click [Local Area Connection], and open [Properties].

4Select [Internet Protocol (TCP/IP)] and click the [Properties] button. Make a note of

the original network settings (IP address, subnet mask, default gateway, etc).

5Select [Use the following IP address] and set the IP address and subnet mask.

The factory default IP address for the projector is “192.168.254.254”. Set an IP

address which is different from this.

Example

IP address:192.168.254.1

Subnet mask: 255.255.255.0

6When the settings are completed, click the [OK] button and then click the [OK] button

on the [Local Area Connection Properties] window to close it.

Preparing the Remote Control

170

■Mac OS X

1Open the Apple Menu and select [System Preferences].

2In the System Preferences window, click [Network] to display the Network window.

3Select [Built-in Ethernet] and click the [TCP/IP] tab. Make a note of the original net-

work settings (IP address, subnet mask, router, DNS server, etc.).

4 Create a new network environment and set the IP address and subnet mask.

The factory default IP address for the projector is “192.168.254.254”. Set an IP

address which is different from this.

Example

IP address:192.168.254.1

Subnet mask: 255.255.255.0

5Click [Apply] to close the network preference window.

■Resetting the IP Address Setting of the Computer

Follow the same procedure as for changing the IP address and reset the values to the

original values based on the notes taken before the change.

171

Installation Manual Connecting to a Networ

Network Settings on the Projector

From the projector menus screen, network

settings can be configured in the [Network

Setting] tab. For the menu operations,

refer to page 88.

(The screen is for the WUX5000 /

WUX4000.)

Locking the Network Settings

You can lock / unlock the network settings

so that they cannot be changed and cancel

the lock.

MENU > [Network Setting] > [Network Setting

lock]

After the OK button is pressed to accept

your setting and the MENU button or the

EXIT button (WUX6000 / SX6000) is

pressed to close the window, the lock is

re-engaged. If you change the network

settings, be sure to continue operating

without closing the window.

• [Lock] is the factory default.

• For the default network password, refer to

page 173.

Unlock Cancels the lock and allows

other network settings to be

changed. The password must

be entered in order to cancel the

lock.

When [Unlock] is selected, the

window shown below appears.

Use the [] / [] / [] / [] but-

tons to enter the 4-digit pass-

word.

For the WX6000 / SX6000, num-

bers can be entered using the

numerical buttons on the remote

control.

Lock Lock the settings.

Network Settings on the Projector

172

Turning the Network Function

On / Off

You can turn the projector network function

on or off. Power can be saved by turning

the function [Off].

MENU > [Network Setting] > [Network function]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [Off] is the factory default.

Forcibly canceling the network lock

In the Network Password Input screen, press the

buttons in the following sequence to cancel the

lock: [ ] [OK] [ ] [OK] [ ] [OK]. This will reset

the network password to [ ] [ ] [ ] [ ].

Off Disables the network function.

On Enables the network function.

173

Network Settings on the Projector

Installation Manual Connecting to a Networ

Setting a Network Password

You can set whether or not a password is

required in order to change the projector

network settings.

MENU > [Network Setting] > [Network Pass-

word setting]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [On] is the factory default.

Registering a Network Pass-

word

MENU > [Network Setting] > [Register Network

Password]

When [Register Network Password] is

selected, the window shown below

appears.

Enter a 4 digit password.

For the WUX5000 / WUX4000, the pass-

word can be entered using the [ ] / [ ] /

[ ] / [ ] buttons. For the WX6000 /

SX6000, the password can be entered

using a combination of the numerical but-

tons and the [ ] / [ ] / [ ] / [ ] buttons.

[ ] / [1], [ ] / [2], [ ] / [3], and [ ] / [4]

have the same function.

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• The factory default is [ ] [ ] [ ] [ ]

(WUX5000 / WUX4000) or [1] [1] [1] [1]

(WX6000 / SX6000).

Off A network password is not used.

On A network password is used.

Network Settings on the Projector

174

Turning the PJLink Function

On / Off

You can turn the PJLink network function

on or off. When the function is turned on,

control is possible via the LAN using com-

mands that meet PJLink standards.

MENU > [Network Setting] > [PJLink]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [On] is the factory default.

• This projector conforms to Class 1 as

defined in the PJLink standards of the

JBMIA (Japan Business Machine and

Information System Industries Associa-

tion). This projector supports all com-

mands that are defined by PJLink Class 1,

and has been verified as conforming to the

PJLink standard Class 1 definition.

• For information about using PJLink, refer to

page 187.

Off Disables the PJLink function.

On Enables the PJLink function.

What is PJLink?

In September 2003, the PJLink Work-

ing Group was established under the

Data Projector Committee. During the

first year, this PJLink Working Group

standardized PJLink as a new inter-

face specification for projectors.

PJLink is a unified standard for opera-

tion and control of projectors.

It allows centralized control of projec-

tors and operation from a controller for

all projectors regardless of manufac-

turer.

The objective is for JBMIA to improve

convenience for users and expand

the use of projectors through early

systemization for network monitoring

and control of projectors, which will

become the mainstream in the future.

Class 1: Standardization of control

and monitoring specifications for

basic projector functions

Basic projector control: Power control,

input selection, etc.

Acquisition of projector information

and status: Power status, input selec-

tion status, error status, lamp use

time, etc.

JBMIA: Japan Business Machine and

Information System Industries

Association

The Japan Business Machine

and Information System

Industries Association is an

organization which was

launched in 1960 and

changed its name on April 1,

2002.

PJLink is a registered trademark of JBMIA and

pending trademark in some countries.

175

Network Settings on the Projector

Installation Manual Connecting to a Networ

Turning DHCP Function On /

Off

You can turn the projector DHCP function

on or off.

MENU > [Network Setting] > [DHCP]

Press the OK button to accept your setting

and then press the MENU button or EXIT

button (WX6000 / SX6000).

• [Off] is the factory default.

TCP / IP Setting

Configure the projector TCP / IP settings.

MENU > [Network Setting] > [TCP/IP setting]

When [TCP/IP setting] is selected, the win-

dow shown below appears. Use the [] /

[ ] buttons to select the IP address, then

press the OK button. Next, use the [ ] /

[ ] buttons to select the digit and the [] /

[ ] buttons to change the value. For the

WX6000 / SX6000, numbers can be

entered using the numerical buttons on

the remote control. Press the OK button,

then set the subnet mask and gateway

address in the same way. Finally, select

[Enter].

• The factory defaults are shown below.

IP address 192.168.254.254

Subnet mask 255.255.255.0

Gateway address 0.0.0.0

• Settings cannot be made when [DHCP]

(P175) is [On].

• If an invalid value is entered, the message

“Invalid entry” appears. If this occurs,

enter a valid value.

Off Disables the DHCP function. TCP / IP

settings are possible.

On Enables the DHCP function.

Searches the DHCP server. Because

the IP address is acquired from the

DHCP server, it is not necessary to

enter the TCP / IP settings (IP

address, subnet mask, gateway

address).

Network Settings on the Projector

176

Initializing Network Settings

You can initialize the projector network set-

tings.

MENU > [Network Setting] > [Network setting

initialization]

When [Network setting initialization] is

selected, the window shown below

appears. Select [YES] then press the OK

button.

• The following items are initialized.

Network setting screen user name, various

settings including password

Network Password setting

PJLink

DHCP

IP address

Subnet mask

Gateway address

E-mail sender address

E-mail recipient address

Projector name

Location

177

Installation Manual Connecting to a Networ

Configuring the Network From the Computer

■Displaying and Configuring the Network Configuration Screen

The web browser screen shown below is for the WUX4000.

1Turn on the computer and projector.

2Launch a web browser, enter “http://(projector IP address)” in the address bar, and

press the Enter key.

The password input screen appears.

3Enter the user name and password on the password input screen, then click OK.

The factory default user name is “root” and the password is “system”.

The projector web screen appears in the web browser.

The factory default IP address is “192.168.254.254”. If DHCP settings are used, ask the net-

work administrator for the projector IP address. It is possible to check the IP address from

the projector menu.

Configuring the Network From the Computer

178

The following information is displayed.

*1 WUX5000 / WX6000 / SX6000

*2 WUX4000

4To configure, click [Settings].

The settings window appears.

Projector name The name of the projector on the network

Location The location of projector installation

MAC address The MAC address of the projector

IP address The IP address of the projector

Power Status The power status of the projector

Lamp Time *1 Lamp operating time

Lamp Time Normal Mode *2 Lamp operating time in [Normal] lamp mode

Lamp Time Quiet Mode *2 Lamp operating time in [Quiet] lamp mode

Lamp Time Converted *2 Lamp operating time (converted value)

Filter Time Air filter operating time

Alert Error message (if an error has occurred)

Temperature abnormality

Faulty lamp

Faulty lamp cover

Faulty cooling fan

Faulty power supply

Faulty lens connector: Lens connector error

Faulty air filter unit: Air filter error

Unknown error

To operate the projector from the computer, click [Projector control] (P188).

179

Configuring the Network From the Computer

Installation Manual Connecting to a Networ

5Select the function to set from the menu (1), then enter the setting in the displayed

field (2) and click [OK] (3).

6A confirmation window appears. Check the contents and if they are correct, click

[Apply].

The settings are applied to the projector and “Save completed” is displayed.

7Click [Back to top] to return the web screen to the initial page.

(2)

(1)

(3)

Configuring the Network From the Computer

180

■Resetting to Factory Defaults

1Perform steps 1 - 3 on page 177 to display the setting window.

2Click [Initialize].

3A confirmation window appears. Click [OK].

■Setting Errors

When a setting-related error occurs, the error name is displayed on the screen, and a

“!” mark is displayed next to the input field which caused the error.

181

Configuring the Network From the Computer

Installation Manual Connecting to a Networ

The error meanings are as shown below.

Error Meaning

Input error A setting outside the valid range was set on the

setting screen.

Password setting error The set password and confirmation password did

not match.

Invalid SMTP The SMTP server IP address has not been set.

System failed to connect SMTP

server.

Failed to connect to the SMTP server when send-

ing a test mail.

System failed to connect POP3

server.

Failed to connect to the POP3 server attempting to

send a test mail.

System doesn't support this auth

type.

An authentication type was set which is not sup-

ported by the server.

System failed to authenticate. Authentication failed attempting to send a test mail.

The system failed to send the test

mail.

Sending of test mail failed due to a connection fail-

ure with the SMTP server or an error which does

not ordinarily occur.

Save Failed Mismatch in settings occurred when settings were

changed at the same time from multiple comput-

ers.

182

Setting Up the Network

■Setting Basic Information [Network]

From [Network] in the settings window, you can log into the web screen and set basic

network information. For the setting procedure, refer to page 177.

Item Explanation Factory default setting

Password

User name When logging into the web screen,

enter the user name in 1-byte

alphanumeric characters and

symbols (4 -15 characters).

root

New password When logging into the web screen,

enter the password in 1-byte

alphanumeric characters and

symbols (4 -15 characters).

system

Confirm new password For confirmation, enter the same

password that you entered in [New

password].

system

TCP/IP

DHCP Select whether to turn the DHCP

function on or off. If the function is

on, because the IP address is

acquired from the server, it is not

possible to enter the [IP address],

[Subnet mask], and [Default gate-

way].

OFF

IP address Enter the IP address of the projec-

tor in 1-byte numbers.

192.168.254.254

Subnet mask Enter the subnet mask in 1-byte

numbers.

255.255.255.0

Default gateway Enter the default gateway IP

address in 1-byte numbers.

0.0.0.0

If settings related to TCP / IP were changed, it is necessary to disconnect and reconnect to

the network. If the network subnet mask was changed, select [Subnet mask] in the above

window and set the new subnet mask.

183

Setting Up the Network

Installation Manual Connecting to a Networ

■Setting Up Email [Mail]

From [Mail] in the settings window, you can set the items necessary to send error

mails and test mails. For the setting procedure, refer to page 177.

Item Explanation Factory default setting

To: Enter the recipient address for error

mails in 1-byte alphanumeric char-

acters and symbols (1 - 63 charac-

ters).

MailUserAccount

Cc: Enter the CC address for error mails

in 1-byte alphanumeric characters

and symbols (1 - 63 characters).

<Blank>

From: Enter the sender address for error

mails in 1-byte alphanumeric char-

acters and symbols (1 - 63 charac-

ters).

Projector@canon.co.jp

SMTP server IP address Enter the SMTP server IP address in

1-byte numbers.

0.0.0.0

SMTP server port number Enter the SMTP server port number

in 1-byte numbers (1 - 65535).

SNTP server IP address Enter the SNTP server IP address in

1-byte numbers.

0.0.0.0

Time zone Select the time zone where the pro-

jector is used.

(GMT) Dublin, Lisbon,

London

Mail resend interval Enter the interval for resending mail

when an error occurred (units: sec-

onds) within the range of 0 - 59 sec-

onds using 1-byte numbers.

Mail resend times Enter the number of times to resend

mail when an error occurred within

the range of 0 - 255 using 1-byte

numbers.

Error report Select whether to turn the error mail

sending function on or off.

OFF

Setting Up the Network

184

■Mail Authentication Settings [Mail auth]

From [Mail auth] in the settings window, you can configure the settings for authentica-

tion of mail that is sent when an error occurs. For the setting procedure, refer to page

177.

Item Explanation Factory default set-

ting

Mail authentication Select the mail authentication method.

If OFF is selected, the other mail

authentication settings cannot be

changed.

OFF

User name Enter the user name to use for mail

authentication in 1-byte alphanu-

meric characters and symbols (1 - 63

characters).

<Blank>

Password Enter the password for mail authenti-

cation in 1-byte alphanumeric charac-

ters and symbols (1 - 63 characters).

<Blank>

Confirm password For confirmation, enter the same

password as you entered in [Pass-

word].

<Blank>

POP3 server IP address Enter the POP3 server IP address in

1-byte numbers.

0.0.0.0

POP3 server port number Enter the POP3 server port number in

1-byte numbers (1 - 65535).

110

POP before SMTP response time Enter the wait time from POP3 authen-

tication to SMTP authentication (units:

milliseconds) using 1-byte numbers

(0 - 9999 milliseconds).

300

185

Setting Up the Network

Installation Manual Connecting to a Networ

■Sending a Test Mail [Send test mail]

From [Send test mail] in the settings window, you can send a test mail to the mail

address that was set in [Mail]. The settings cannot be changed from this window.

■SNMP Settings [SNMP]

From [SNMP] in the settings window, you can configure the settings related to control

of projectors which use SNMP (Simple Network Management Protocol). For the set-

ting procedure, refer to page 177.

Item Explanation

To:

The recipient address which was set from [Mail] in the settings window

(

P183

)

is displayed.

Cc:

The CC address which was set from [Mail] in the settings window (

P183

)

is displayed.

From:

The sender name which was set from [Mail] in the settings window

(

P183

)

is displayed.

Subject:

The predetermined mail

title “Canon Projector test” is displayed.

Setting Up the Network

186

■Setting Projector Information [Projector info.]

From [Projector info.] in the settings window, you can set the names and location

names which are used to identify projectors when multiple projectors are installed on

the network. For the setting procedure, refer to page 177.

Item Explanation Factory default setting

SNMP Select the SNMP function version. If OFF is

selected, the SNMP function will be turned

off and the other settings in this window

cannot be changed.

OFF

Receive community Enter the community name which will

receive projector information in 1-byte

alphanumeric characters and symbols (1 -

15 characters).

<Blank>

Password Enter the community settings password in

1-byte alphanumeric characters and sym-

bols (8 - 15 characters). This is also used

as the password for trapping. It can be set

only when the SNMP version is V3.

<Blank>

Confirm password For confirmation, enter the same password

as you entered in [Password].

<Blank>

SNMP trap Select the type of error to trap. When any of

the checkboxes is turned on, it becomes

possible to set [Trap IP address] and [Trap

community].

OFF (no checkmarks)

Trap IP address Enter the IP address to send information to

when trap occurs. Enter in 1-byte numbers.

0.0.0.0

Trap community Enter the community name which will send

information when trap occurs. Enter in 1-

byte alphanumeric characters and symbols

(1 - 15 characters).

<Blank>

Item Explanation Factory default setting

Projector name Enter the projector name in 1-byte alphanu-

meric characters and symbols (1 - 63 char-

acters).

WUX5000 / WUX4000 /

WX6000 / SX6000

Location Enter the projector installation location in 1-

byte alphanumeric characters and symbols

(0 - 63 characters).

<Blank>

187

Setting Up the Network

Installation Manual Connecting to a Networ

■Setting PJLink [PJLink]

From [PJLink] in the setting window, you can set the PJLink functions which are the

standard for projector management on a network. For the setting procedure, refer to

page 177. For information about PJLink, refer to page 174.

Item Explanation Factory default

setting

PJLink Turn the PJLink function on or off. If

OFF is selected, the PJLink func-

tion will be turned off and the other

settings in this window cannot be

changed.

PJLink authentication Select whether to turn the PJLink

authentication function on or off. If

OFF is selected, [Password] and

[Confirm password] cannot be

changed.

Password Enter the PJLink authentication

password in 1-byte alphanumeric

characters (1 - 32 characters).

system

Confirm password For confirmation, enter the same

password that you entered in

[Password].

system

188

Controlling the Projector from a Computer

When the projector is connected to a network, it is possible to control the projector from a

computer via the network.

1Turn on the computer and projector.

2Launch a web browser, enter “http://(projector IP address)” in the address bar, and

press the Enter key.

The password input screen appears.

The factory default IP address is “192.168.254.254”. It is possible to check the IP

address from the projector menu.

3Enter the user name and password on the password input screen, then click OK.

The factory default user name is “root” and the password is “system”.

4The projector web screen appears in the web browser. Click [Projector control].

Controlling the Projector from a Computer

189

Installation Manual Connecting to a Networ

5The projector control screen appears. The projector can be controlled from this

screen.

6When the operations are finished, click [Back to top] to return the initial web screen.

Item Explanation

Projector name The name of the connected projector is displayed. (P186)

IP address The IP address of the connected projector is displayed. (P182)

Refresh Refreshes the displayed contents with the most recent informa-

tion.

Power Turns projector power on or off.

Input Select an input signal and click [Apply] to change to that input

signal. (P59)

Aspect Select an aspect and click [Apply] to change to that aspect. (P69)

Image mode Select an image mode and click [Apply] to change to that image

mode. (P78)

Blank Switches the blank setting on or off. (P82)

Mute Switches the mute setting on or off. (P83)

Auto PC Performs Auto PC. (P62)

Information The control results and control error information are displayed at

the top of the screen.

190

Error Mail

The messages shown in the following error list are sent when an error occurs in the pro-

jector.

Error list

* For details, contact the Canon Customer Support Center.

Errors related to

temperature

Error

name

Temperature abnormality

Text The temperature inside the projector is too high for some reason or the

outside air temperature is higher than the specified one.

If the problem is inside the projector, check whether the projector is

installed and operated normally, turn off the projector to cool its inside,

and retry projection. If the same warning occurs again, the projector

may be defective. Contact your dealer.

Errors related to

the lamp

Error

name

Faulty lamp

Text The lamp has burnt out. Replace the lamp with a new one. If the same

warning occurs again, the lamp drive circuit may be defective. Con-

tact your dealer.

Errors related to

the lamp cover

Error

name

Faulty lamp cover

Text The lamp cover is open. Check whether the lamp cover is installed

properly. If it is installed properly, the lamp cover detection switch may

be defective. Contact your dealer.

Errors related to

the cooling fan

Error

name

Faulty cooling fan

Text The cooling fan or another component may be defective. Contact your

dealer.

Errors related to

the power supply

Error

name

Faulty power supply

Text The voltage of part of the power supply is abnormally high or any

other problem has occurred in the power supply. Contact your dealer.

Errors related to

the lens connec-

tor

Error

name

Faulty lens connector

Text The lens cable is not connected to the lens unit. Check whether the

lens cable is connected to the lens unit properly.

If it is connected properly, the lens connector or cable may be defec-

tive. Contact your dealer.

Errors related to

the air filter

Error

name

Faulty air filter unit

Text The air filter unit is not installed properly.

Check whether the air filter unit is installed properly.

If it is installed properly, the air filter unit detection switch may be

defective. Contact your dealer.

Other types of

errors

Error

name

Unknown Error

Text Code in hexadecimal numbers*

Projecting an Image

Safety Instructions

Before Use

Table of Contents

Useful Functions Available

During a Presentation

Setting Functions from Menus

Installation

Connecting to a Network

Maintenance

Appendix

Index

Appendix

User’s Manual

Installation Manual

191

Maintenance

192

Cleaning the Projector

Clean the projector frequently to prevent dust from settling on the surface.

A dirty lens may ruin the quality of the projected image.

Wipe the projector’s main unit softly with a soft cloth.

If the projector is heavily soiled, soak the cloth in water with a small amount of detergent

in it, squeeze the cloth thoroughly, and then wipe the projector with it. After cleaning, wipe

the projector with a dry cloth.

When cleaning the projector, make sure to turn off the projector,

wait until the cooling fan stops, disconnect the power plug from the

electrical outlet, and let the projector stand for at least 1 hour. Oth-

erwise, you may get burned because the main unit is very hot

immediately after the projector is turned off.

• Never use volatile cleaning liquid or benzine, as these may damage the finish of the pro-

jector.

• When using a chemical dust cloth, make sure to read the instructions thoroughly.

• When cleaning the projector’s lens, use a commonly available air blower or lens cleaning

paper. The lens surface is easily damaged, so do not use a hard cloth or tissues.

193

Installation Manual Maintenance

Cleaning and Replacing the Air Filter

Replacing the Air Filter

Follow the procedure below when replacing the air filter.

1Turn off the projector power and remove the power plug.

2Hook your finger onto the handle of the

air filter on the side of the projector, and

pull the air filter out to remove it.

3Remove the filter from the air filter

frame. First disengage the tab on the

inside, then remove the entire air filter

from the frame.

4Install a new air filter into the frame.

First insert the air filter tab into the

groove on the handle side of the frame,

then press the air filter into the frame.

Air filter

Cleaning and Replacing the Air Filter

194

5Securely insert the air filter all the way

into the projector.

Cleaning the Air Filter

The air filter protects the lens and mirror inside the projector from dust and dirt. Should

the air filter become clogged with dust, the projector may be damaged since it will block

the air flow into the projector and raise the internal temperature of the projector. The fol-

lowing screen is displayed when turning on the projector if the air filter needs to be

cleaned (after approx. 300 hours). Clean the air filter if it is displayed.

• Turn the power of the projector off and pull out the power plug.

• Hook your finger into the air filter handle on the side of the projector, and remove the air

filter. Then use a vacuum cleaner to remove the dust.

• If the filter replacement screen is displayed when turning on the projector after cleaning

the air filter, select [Yes] and press OK. The filter replacement screen will disappear.

• This screen is not displayed when [Filter warning display] is set to [Off]. (WX6000 /

SX6000) (P137)

• Handle the air filter carefully. If damaged, the air filter will not work properly.

• When the lamp is replaced, it is recommend that you also replace the air filter.

• Contact the Canon Customer Support Center for further information.

• Replacement air filter part No.: RS-FL01

• This can also be purchased from the Canon home page

(http://store.canon.jp/user/ListProducts/list?svid=2&sc=LMPPR&jsp=/jsp/search/

search_item_acc.jsp).

• Only the [ ], [ ], OK and POWER buttons are

available while this screen is displayed. (When you

press the POWER button, the message “Push

POWER button again to turn off power” appears.)

• When this screen has disappeared after being dis-

played for 10 seconds, all buttons become opera-

ble.

195

Installation Manual Maintenance

Replacing the Lamp

When the usage time of the lamp exceeds a certain amount of time, the following mes-

sage (two types) is displayed for 10 seconds every time the projector is turned on.

2,700 hours to less than 3,000 hours

Prepare a new lamp when this screen is displayed.

• Only the [ ], [ ], OK and POWER buttons are available while this screen is displayed.

• When you press the POWER button, “Push POWER button again to turn off power.”

message appears.

• After this screen has been displayed for 10 seconds and disappeared, all buttons

become operable.

• This message will not be displayed again if you select [Cancel] in response to the mes-

sage “Do you want to display this message again?”.

3,000 hours or more

If this screen is displayed, replace the lamp by referring to the procedure on page 196.

•Only the POWER button is available while this screen is displayed.

• When you press the POWER button, the “Push POWER button again to turn off power.”

message appears.

• When this screen has disappeared after being displayed for 10 seconds, all buttons

become operable.

• You can check the usage time of the lamp in [Lamp counter] in the [System settings]

menu. (P135)

• This screen is not displayed when [Lamp warning display] is set to [Off]. (WX6000 /

SX6000) (P135)

Replacing the Lamp

196

Replacement Lamp

This projector uses the following lamps.

Lamp part No.: RS-LP06 (WUX4000)

RS-LP07 (WUX5000 / WX6000 / SX6000)

Contact the Canon Customer Support Center when purchasing a replacement lamp.

Replacing the Lamp

1Turn off the projector power and remove the power plug.

2Loosen one screw and open the lamp cover in the direction of the arrow.

The lamp cover screw is attached to the lamp cover and designed to prevent it from

falling off.

When replacing the lamp, turn off the projector, wait until the cool-

ing fan stops, disconnect the power plug from the electrical outlet,

and let the projector stand for at least 1 hour. Otherwise, you may

get burned because the main unit is very hot immediately after the

projector is turned off.

• Be sure to use the specified lamp.

• Contact the Canon Customer Support Center or access to the

Canon home page.

• Do not touch the inner glass surface when you replace the lamp.

Doing so may cause deterioration to the projector’s performance.

• Be sure to handle the lamp carefully and correctly since it may

break during use if it has been scratched or subjected to impact.

If the lamp breaks, contact the Canon Customer Support Center

or follow the instructions on page 21 and page 22.

• When replacing the lamp, do not remove any screws other than

those specified.

Screw

197

Replacing the Lamp

Installation Manual Maintenance

3Loosen the 3 screws on the inside of the lamp unit, then slowly pull out the lamp unit in

the direction of the arrow.

Even when the screws are loosened, they will not fall off the lamp unit.

4Fully insert a new lamp unit and secure it with the 3 screws.

5Close the lamp cover and tighten the screws.

6Turn on the power. Bring up the menu and select [System settings] - [Other settings] -

[Lamp counter].

(The screen is for the WUX5000 / WUX4000.)

Replacing the Lamp

198

7Select [Reset] - [OK] to reset the lamp counter.

• It is recommended that you also replace the air filter when you replace the lamp.

• Contact the Canon Customer Support Center for further information.

• Replacement air filter product number: RS-FL01

(The screen is for the WUX5000 / WUX4000.)

199

MULTIMEDIA PROJECTOR

Appendix

200

Projecting an Image

Safety Instructions

Table of Contents

Useful Functions Available

During a Presentation

Setting Functions from Menus

Installation

Connecting to a Network

Maintenance

Appendix

Index

Appendix

User’s Manual

Installation Manual

Before Use

201

Appendix

202

Troubleshooting

LED Indicator Meanings

When there is a problem with the projector, the LED indicator on the side of the projector

illuminates or flashes continuously after the projector is turned off.

• Wait until the cooling fan stops and disconnect the power plug from the electrical outlet

before dealing with the problem.

LED indicator

status Meaning Countermeasure

WARNING and

TEMP are lit.

Temperature

abnormality

The temperature inside the projector is too high for some

reason or the outside air temperature is higher than the oper-

ating range. If the problem is inside the projector, check

whether the projector is installed and operating normally,

unplug the projector from the power outlet to cool down the

projector interior and then restart projection. If the air intake

or exhaust vent is blocked, remove the obstacle. If the same

warning occurs again, there may be a malfunction in the

projector. Contact the Canon Customer Support Center.

WARNING and

LAMP are lit.

Faulty lamp The lamp does not illuminate. Turn the power off and then

back on and check whether or not the lamp illuminates.

Also, check whether the air intake or exhaust vent is

blocked, and whether the air filter is clogged with dust. The

warning may indicate if the air flow in and out of the projector

is blocked, or if the internal temperature of the projector

rises. If the air filter is clogged, clean or replace the air filter.

(P193, P194) If the lamp does not illuminate, replace it. If the

same warning occurs again, there may be a malfunction in

the lamp drive circuit. Contact the Canon Customer Support

Center.

WARNING

flashes 3

times, LAMP is

lit.

Faulty lamp

cover

The lamp cover is open. Unplug the projector from the elec-

trical outlet, then install the lamp cover correctly and turn on

the projector again. If the lamp cover has been installed

properly, there may be a malfunction in the lamp cover

detection switch. Contact the Canon Customer Support

Center.

WARNING

(only) flashes 4

times repeat-

edly.

Faulty cool-

ing fan

There may be a malfunction in the cooling fan or another

component. Unplug the projector from the electrical outlet,

then plug it into the outlet and turn on the projector again.

Contact the Canon Customer Support Center if the same

warning occurs again.

WARNING

(only) flashes 5

times repeat-

edly.

Faulty power

supply

Abnormal voltage is applied to some parts in the power sup-

ply or another failure may have occurred. Unplug the projec-

tor from the electrical outlet, then plug it back into the outlet

and turn on the projector again. Contact the Canon Cus-

tomer Support Center if the same warning occurs again.

203

Troubleshooting

endix Other Information

Symptoms and Solutions

■You Cannot Turn on the Projector

■You Cannot Project an Image from the Projector

WARNING

(only) flashes 6

times repeat-

edly.

Faulty lens

connector

Disconnect the lens connector which joins the lens unit and

projector. Contact the Canon Customer Support Center.

WARNING

(only) flashes 3

times repeat-

edly.

Filter error The air filter is not installed. Check whether or not the air filter

is installed correctly. Contact the Canon Customer Support

Center if the same warning occurs again.

Cause Countermeasure

The power cord is not connected

correctly.

Check whether the power cord is connected correctly.

(P56)

The power cord has just been

connected.

You cannot turn on the projector until the [STAND BY] indi-

cator turns red after connecting the power plug. (P56)

The lamp cover is open. Unplug the projector from the power outlet, then install the

lamp cover correctly and turn on the projector again.

The safety device is activated

because the air intake or the

exhaust vent is blocked and the

internal temperature of the projec-

tor has increased.

When the safety device is active, the [STAND BY] indicator

does not turn on when you connect the power cord. You

cannot disable this safety device. Remove any obstacle

that is blocking the air intake or exhaust vent and contact

the Canon Customer Support Center.

The lens connector is not con-

nected correctly.

The lens connector that connects the lens unit with the main

unit of the projector is disconnected. Contact the Canon

Customer Services Center.

The air filter is not installed cor-

rectly.

Check whether the air filter is installed correctly. (P193)

Key lock is enabled. Check that Key lock (P123) is not enabled for the projector

or the remote control.

Cause Countermeasure

A cable is not connected cor-

rectly.

Check whether the projector is connected to the computer

or AV equipment correctly. (P52, P59)

20 seconds have not elapsed

since the projector was turned on.

When the projector is turned on, the opening window is dis-

played for approximately 20 seconds. To project an image

immediately, press the OK button on the remote control or

side control. (P56)

No image is sent from the AV

equipment.

Check whether an image is played on the connected video

camcorder, DVD, etc.

LED indicator

status Meaning Countermeasure

Troubleshooting

204

■There is no Sound

Connection with the input terminal

has not been performed correctly.

Check whether the AV equipment is connected to the pro-

jector input terminal correctly. (P47)

No input signal type has been

selected for the connected AV

equipment.

Check that the same input signal has been correctly

selected for the connected AV equipment from the [INPUT]

menu. (P60)

The input signal type is incorrect. Check whether the selected input signal type is correct.

(P94, P218)

The BLANK function has been

selected.

Press the BLANK button on the remote control. (P82)

No image is projected due to a

problem with the computer.

Turn first the projector and then the computer off and then

back on again.

The external monitor output is not

set on the notebook computer

correctly.

Turn on the external monitor output on the notebook com-

puter. To turn on the external monitor output, press the

[LCD] or [VGA] function key or a key with an icon for the

external monitor, while holding down the [Fn] key on the

keyboard of the notebook computer. With Windows 7, you

can turn on image output by holding down the Windows

logo key and pressing the [P] key. (P58)

The combination of keys used to perform this operation var-

ies depending on the model of notebook computer. For

more detailed information, refer to the manual that came

with your computer.

The displayed image is not the

same as that displayed on the

computer.

Check whether the dual screen (multi-display) mode is

selected on the computer. If the dual screen mode has

been selected, change it to the simultaneous display mode

on the computer.

The output setting method varies among computer manu-

facturers. For more detailed information, refer to the manual

that came with your computer.

Cause Countermeasure

The audio cable is not connected

correctly.

Check the audio cable connection. (P162)

The MUTE function is enabled. Press the MUTE button on the remote control. (P83)

The volume level is adjusted to

the minimum.

Press the VOL button on the remote control or the VOL+

button on the side control to adjust the volume level. (P83)

An audio cable with a built-in

resistor is used.

Use an audio cable without a built-in resistor.

Audio in terminal select is [Off]

(WX6000 / SX6000).

Change the Audio In terminal to the appropriate setting.

(P139)

Cause Countermeasure

205

Troubleshooting

endix Other Information

■The Projected Image Is Blurred

■You Cannot Project an Image Appropriately

■The Projector Power Turns Off

Cause Countermeasure

The image is out of focus. Adjust the focus. (P73)

The distance to the screen is too

short.

Check whether the distance to the screen is appropriate. If

the distance is shorter than approximately 1.3 m (4.3'), the

projector cannot focus on the screen. (P156)

The projector is not placed

straight in front of the screen.

Check whether the projector is placed obliquely to the

screen. A slight error in the projection angle can be cor-

rected through the keystone adjustment function. (P76)

The projector has been moved to

a place where the temperature

varies a lot.

When the projector is moved from a location where the tem-

perature is low to a location where the temperature is high,

condensation may form on the lens. The condensation will

evaporate after a period of time and the projector will be

able to project a normal image.

The lens is stained. Clean the lens. (P192)

The tracking is bad. Adjust the tracking with the [AUTO PC] or [Tracking] func-

tion. (P62, P96)

Cause Countermeasure

The projected image is inverted in

the vertical or horizontal direction.

The ceiling mounted / rear projection setting is incorrect.

Check the [Image flip H/V] setting in the [Display settings]

menu. (P104)

The dot clock of the input signal is

higher than 162 MHz with a BNC

cable.

Set the signal dot clock to 162 MHz or less on your com-

puter.

A VGA cable is used in which

some pins are not connected.

Use a VGA cable in which all pins are connected.

Cause Countermeasure

The air intake or exhaust vent is

blocked.

Check whether the air intake or exhaust vent is blocked. If

the air intake or exhaust vent is blocked, the temperature

inside the projector will increase and the power is automati-

cally turned off to protect the projector. (The [WARNING]

indicator and [TEMP] indicator are lit.) Wait until the projec-

tor temperature drops, then make sure that the intake and

exhaust vents are not blocked and turn on the projector.

(P32, P56)

The air filter is dirty. Check whether the air filter is clogged with dust.

If the air filter is clogged, clean or replace the air filter.

(P193)

Troubleshooting

206

■You Cannot Operate the Remote Control

If the above causes cannot be identified, the projector may be damaged. Contact the

Canon Customer Support Center as soon as possible.

The lamp has broken (or there is a

lamp malfunction).

Check whether the lamp has broken.

If the lamp has broken, follow the instructions on page 21. If

the lamp has not broken, there may be a malfunction with

the lamp. Check the lamp by replacing it with a spare lamp

if you have one. (P22, P195, P196)

The operating temperature is

inappropriate.

Check whether the operating temperature is between 5°C

and 35°C. (P24)

If you use the projector at 2300 m or higher above sea level,

contact the Canon Customer Support Center.

Cause Countermeasure

Batteries are not installed prop-

erly or they have run out.

Check whether batteries are installed correctly. If batteries

are installed correctly, replace them with new batteries.

(P27)

You are operating the remote con-

trol from the outside of the remote

control operating range.

Check whether you are operating the remote control within

the remote control operating range of the main unit of the

projector. (P29)

There is an obstacle between the

projector and the remote control.

Remove the obstacle between the infrared remote receiver

of the main unit of the projector and the remote control or

point the remote control in an obstacle-free path.

You are operating the remote con-

trol in an unsuitable operating

environment.

Check whether the infrared remote receiver of the main unit

of the projector is exposed to direct sunlight or strong light

of lighting apparatus. (P29)

The channel setting of the remote

control does not match the setting

of the projector.

Check whether the channel setting of the remote control

has been changed. You can check the [Remote control]

setting in the [System settings] menu. (P124)

The key lock function is prevent-

ing operation of the remote con-

trol.

Check whether [Key lock] is enabled to disable the remote

control operation.

In the System settings menu, set [Key lock] to [Off]. (P123)

When using infrared operation,

the cable is connected to the ter-

minal for the wired remote control

of the projector or remote control

(WX6000 / SX6000).

Pull out the cable that is connected to the terminal for the

wired remote control of the projector or remote control.

(P30)

When using with the cable con-

nected, the cable may not be

connected to the terminal for the

wired remote control of the pro-

jector or remote control (WX6000 /

SX6000).

Check whether the cable is connected to the terminal for

the wired remote control of the projector and remote con-

trol. Also check that the cable is not broken. (P30)

Cause Countermeasure

207

endix Other Information

Relationship between Aspect and Screen Aspect

This section describes the relationship between screen aspect (P63) and aspect (P69).

To project an image on the whole screen, select the most appropriate screen aspect ratio

and aspect according to the aspect ratio of the screen and input signal type.

• If an image from image software with an aspect ratio of 16:9 is not projected correctly, select [16:9]

as the screen aspect.

• For a 16:9 image with black borders at the top and bottom, such as a terrestrial broadcast movie,

you can project the 16:9 image area so that it is projected on the entire screen by selecting [Zoom]

in [Aspect].

[Zoom] is available when [16:10], [16:9] or [16:9 D. image shift] is selected for the screen aspect

and [HDMI (480p, 576p)] or [Component (480p, 480i, 576p, 576i)] is selected for the input signal.

• To perform keystone adjustment (P76), select [16:10], [4:3] or [16:9] for [Screen aspect].

WUX5000 / WUX4000

■When the image is projected on a 16:10 screen

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[16:10]

[Full]

[Auto]

(16:9)

1920 x 1080

1280 x 720 [Full]

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[Full]

Relationship between Aspect and Screen Aspect

208

■When the image is projected on a 16:9 screen

■When the image is projected on a 4:3 screen

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[16:9]

[16:9 D. image shift]

[16:9]

(16:9)

1920 x 1080

1280 x 720

[16:9]

[Auto]

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[16:9]

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[4:3]

[4:3 D. image shift]

[4:3]

(16:9)

1920 x 1080

1280 x 720 [4:3]

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[4:3]

[Auto]

209

Relationship between Aspect and Screen Aspect

endix Other Information

■When projecting on a 16:10 screen in the aspect ratio of the connected

device

■When projecting on a 16:9 screen in the aspect ratio of the connected

device

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[16:10]

[Full]

[Auto]

(16:9)

1920 x 1080

1280 x 720

[16:9]

[Auto]

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[4:3]

[Auto]

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[16:9]

[16:9 D. image shift]

[Auto]

(16:9)

1920 x 1080

1280 x 720

[16:9]

[Auto]

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[4:3]

[Auto]

Relationship between Aspect and Screen Aspect

210

■When projecting on a 4:3 screen in the aspect ratio of the connected

device

WX6000

■When the image is projected on a 16:10 screen

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[4:3]

[4:3 D. image shift]

[Auto]

(16:9)

1920 x 1080

1280 x 720

[16:9]

[Auto]

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[4:3]

[Auto]

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[16:10]

[Auto]

(16:9)

1920 x 1080

1280 x 720 [16:10]

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[16:10]

211

Relationship between Aspect and Screen Aspect

endix Other Information

■When the image is projected on a 16:9 screen

■When the image is projected on a 4:3 screen

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[16:9]

[16:9 D. image shift]

[16:9]

(16:9)

1920 x 1080

1280 x 720

[16:9]

[Auto]

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[16:9]

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[4:3]

[4:3 D. image shift]

[4:3]

(16:9)

1920 x 1080

1280 x 720 [4:3]

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[4:3]

[Auto]

Relationship between Aspect and Screen Aspect

212

■When projecting on a 16:10 screen in the aspect ratio of the connected

device

■When projecting on a 16:9 screen in the aspect ratio of the connected

device

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[16:10]

[Auto]

(16:9)

1920 x 1080

1280 x 720

[16:9]

[Auto]

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[4:3]

[Auto]

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[16:9]

[16:9 D. image shift]

[16:10]

[Auto]

(16:9)

1920 x 1080

1280 x 720

[16:9]

[Auto]

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[4:3]

[Auto]

213

Relationship between Aspect and Screen Aspect

endix Other Information

■When projecting on a 4:3 screen in the aspect ratio of the connected

device

SX6000

■When the image is projected on a 4:3 screen

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[4:3]

[4:3 D. image shift]

[16:10]

[Auto]

(16:9)

1920 x 1080

1280 x 720

[16:9]

[Auto]

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[4:3]

[Auto]

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[4:3]

[Auto]

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[4:3]

(16:9)

1920 x 1080

1280 x 720 [4:3]

Relationship between Aspect and Screen Aspect

214

■When the image is projected on a 16:10 screen

■When the image is projected on a 16:9 screen

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[16:10]

[16:10 D. image shift]

[16:10]

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[16:10]

[Auto]

(16:9)

1920 x 1080

1280 x 720 [16:10]

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[16:9]

[16:9 D. image shift]

[16:9]

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[16:9]

(16:9)

1920 x 1080

1280 x 720

[16:9]

[Auto]

215

Relationship between Aspect and Screen Aspect

endix Other Information

■When projecting on a 4:3 screen in the aspect ratio of the connected

device

■When projecting on a 16:10 screen in the aspect ratio of the connected

device

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[4:3]

[Auto]

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[16:10]

[Auto]

(16:9)

1920 x 1080

1280 x 720

[10:9]

[Auto]

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[16:10]

[16:10 D. image shift]

[4:3]

[Auto]

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[16:10]

[Auto]

(16:9)

1920 x 1080

1280 x 720

[10:9]

[Auto]

Relationship between Aspect and Screen Aspect

216

■When projecting on a 16:9 screen in the aspect ratio of the connected

device

Aspect ratio of

connected device

Screen aspect setting

(P63)Aspect setting (P69) Screen image

(4:3)

1600 x 1200

1400 x 1050

640 x 480

[16:9]

[16:9 D. image shift]

[4:3]

[Auto]

(16:10)

1920 x 1200

1440 x 900

1280 x 800

[16:10]

[Auto]

(16:9)

1920 x 1080

1280 x 720

[16:9]

[Auto]

217

endix Other Information

Displayed Test Patterns

If using WX6000 / SX6000

The test pattern can be displayed by pressing the [TEST PATTERN] button. Use this when

there is no image signal, etc.

While the test pattern is displayed, you can use the [ ] / [ ] buttons to change to a differ-

ent test pattern. Also, if there is an option pattern available, you can use the [ ] / [ ] but-

tons to switch pattern.

The following test patterns can be displayed.

[ ] / [ ] switch pattern Option pattern

([ ] / [ ] switch pattern)

White / red /

green / blue

(Raster 100%)

White / red /

green / blue

(Raster 50%)

Color bar

The following functions in the [Image

adjustment] tab are not applied to the

test pattern.

• Brightness adjustment function

(P111)

• Contrast adjustment function (P112)

• Sharpness adjustment function

(P113)

• Color level adjustment function

(P114)

• Color balance adjustment function

(P114)

218

Supported Signal Types

This projector supports the following signal types.

If your computer or AV equipment is compatible with any one of these signal types, the

projector’s Auto PC function selects the input signal type to project an image appropri-

ately.

ANALOG RGB

DVI

* The specifications in the table above are subject to

change without notice.

* This projector does not support any computer output

signal with a dot clock of higher than 162 MHz.

* Use a VGA cable in which all pins are connected. If the

cable is a type in which all pins are not connected, the

image may not be correctly displayed.

HDMI

Connecting to a computer

Connecting with AV equipment

COMPONENT

Resolution (dots) Signal type Horizontal fre-

quency (kHz)

Vertical fre-

quency (Hz)

640 x 480 VGA 31.469 59.940

720 x 480 - 31.469 59.940

720 x 576 - 31.250 50.000

800 x 600 SVGA 37.879 60.317

848 x 480 - 31.020 60.000

1024 x 768 XGA 48.363 60.004

1280 x 720 - 37.500 50.000

45.000 60.000

1280 x 768

WXGA

47.776 59.870

47.396 59.995

1280 x 800 49.702 59.810

49.306 59.910

1280 x 960 MAC 60.000 60.000

1280 x 1024 SXGA 63.981 60.020

1360 x 768 - 47.712 60.015

1366 x 768 - 47.712 59.790

1400 x 1050 SXGA+ 64.744 59.948

65.317 59.978

1440 x 900 WXGA+ 55.935 59.887

55.469 59.901

1600 x 1200 UXGA 75.000 60.000

1680 x 1050 WSXGA+ 64.674 59.883

65.290 59.954

1920 x 1080 - 56.250 50.000

67.500 60.000

1920 x 1200

(WUX5000 / WUX4000)

WUXGA 74.038 59.950

Resolution (dots) Signal type Horizontal fre-

quency (kHz)

Vertical fre-

quency (Hz)

640 x 480 D-VGA 31.469 59.940

720 x 480 - 31.469 59.940

720 x 576 - 31.250 50.000

800 x 600 D-SVGA 37.879 60.317

1024 x 768 D-XGA 48.363 60.004

1280 x 720 - 37.500 50.000

45.000 60.000

1280 x 800 D-WXGA 49.702 59.810

49.306 59.910

1280 x 1024 D-SXGA 63.981 60.020

1400 x 1050 D-SXGA+ 64.744 59.948

65.317 59.978

1440 x 900 D-WXGA+ 55.935 59.887

55.469 59.901

1600 x 1200 D-UXGA 75.000 60.000

1680 x 1050 D-

WSXGA+

64.674 59.883

65.290 59.954

1920 x 1080 - 56.250 50.000

67.500 60.000

1920 x 1200

(WUX5000 / WUX4000)

D-WUXGA 74.038 59.950

Resolution

(dots) Signal type Horizontal fre-

quency (kHz)

Vertical fre-

quency (Hz)

640 x 480 VGA 31.469 59.940

800 x 600 SVGA 37.879 60.317

1024 x 768 XGA 48.363 60.004

1280 x 800 WXGA 49.702 59.810

49.306 59.910

1280 x 1024 SXGA 63.981 60.020

1400 x 1050 SXGA+ 64.744 59.948

65.317 59.978

1440 x 900 WXGA+ 55.935 59.887

55.469 59.901

1600 x 1200 UXGA 75.000 60.000

1680 x 1050 WSXGA+ 64.674 59.883

65.290 59.954

1920 x 1200

(WUX5000 /

WUX4000)

WUXGA 74.038 59.950

Signal type Horizontal frequency

(kHz)

Vertical frequency

(Hz)

480p 31.469 59.940

576p 31.250 50.000

720p 37.500 50.000

45.000 60.000

1080i 28.125 50.000

33.750 60.000

1080p 56.250 50.000

67.500 60.000

Signal type Horizontal frequency

(kHz) Vertical frequency (Hz)

480i 15.734 59.940

480p 31.469 59.940

576i 15.625 50.000

576p 31.250 50.000

720p 37.500 50.000

720p 45.000 60.000

1080i 28.125 50.000

1080i 33.750 60.000

1080p 56.250 50.000

1080p 67.500 60.000

219

endix Other Information

Product Specifications

■Projector

*1When using a Standard Zoom Lens (RS-IL01ST). Varies depending on the type of lens unit.

*2When lamp mode (WUX4000) is set to [Normal].

*99.99% or more of the LCD panel pixels are effective. During projection, 0.01% or less of pixels may stay lit or unlit due to the characteristics of

the LCD panel.

* Using the projector continuously for an extended period of time may accelerate the deterioration of optical parts.

Model name WUX5000 WUX4000

Display system RGB liquid crystal system

Optical system Color separation by dichroic mirror / polarizing beam splitter and color com-

position by prism

Display device

Type Reflective liquid crystal panel

Size / Aspect ratio 0.71'' X3 / 16:10

Drive system Active matrix system

Number dots / Total number dots 2,304,000 (1920 x 1200) x 3 panels / 6,912,000

Projection

lens(*1)

Zoom ratio / Focal length / F value 1.5x / f = 23.0 - 34.5 mm / F1.89 - F2.65

Zooming / Focusing system Electric / Electric

Lens shift V: -15% - +55%, H: ±10%

Light source 330-NSHA 336 W 310-NSHA 300 / 264 W

(lamp mode Normal / Quiet)

Image size (projection distance) (*1) Size 40 to 600 (1.3 m / 4.6' to 29.0 m / 95.1')

Number of colors 16,770,000 colors (full color)

Brightness (*1) 5,000 lumen 4,000 lumen (*2)

Contrast ratio 1000:1 (Full white: Full black, during presentation)

Ratio of brightness at periphery to center (*1) 88%

Speaker 5W monaural x 1

Maximum input resolution 1920 x 1200 dots

Video signals

Analog PC input

WUXGA / UXGA / WSXGA+ / SXGA+ / WXGA+ / SXGA / WXGA / XGA /

SVGA / VGA

(Scan frequency: Horizontal 15 - 75 kHz, Vertical 50 - 85 Hz)

Digital PC input WUXGA / UXGA / WSXGA+ / SXGA+ / WXGA+ / SXGA / WXGA / XGA /

SVGA / VGA

Component input 1080p, 1080i, 720p, 576i, 576p, 480i, 480p

HDMI input 1080p, 1080i, 720p, 576p, 480p

Input terminal

DVI-D IN terminal Digital PC (24-pin DVI connector)

HDMI IN terminal HDMI (deep color)

ANALOG PC / COMPONENT IN terminal Analog PC, Component (mini D-sub 15-pin)

CONTROL terminal RS-232C (D-sub 9-pin)

AUDIO IN Terminal Audio signal (3.5Ø stereo mini jack x 2)

AUDIO OUT Terminal Audio signal (3.5Ø stereo mini jack)

LAN terminal Network connection (RJ-45)

Input signal

Digital PC TMDS (Transition Minimized Differential Signaling)

Analog PC

0.7Vp-p, positive polarity, impedance = 75Ω

Horizontal / vertical synchronization: TTL level, negative or positive polarity

Composite synchronization in G signal: 0.3Vp-p, negative polarity, imped-

ance = 75Ω

Component video

COMPONENT: Separate Y Cb/Pb Cr/Pr signal

Y: 1Vp-p, negative synchronization, impedance = 75Ω

Cb/Pb: 0.7Vp-p, impedance = 75Ω

Cr/Pr: 0.7Vp-p, impedance = 75Ω

Audio Impedance = 47kΩ or more

Noise 40 dB 39 / 36dB

(lamp mode Normal / Quiet)

Operating temperature 5°C - 35°C

Power supply AC100V - 240V 50 / 60Hz

Power consumption

450W / 1.7W / 0.35W

(Projection / standby / standby with

LAN OFF)

410W / 365W / 1.7W / 0.35W

(normal mode / silent mode / standby

/ standby with LAN OFF)

Dimensions 380 mm (W) x 150 mm (H) x 430 mm (D) / 15.0 (W) x 5.9 (H) x 16.9 (D) in

(not including the projection)

Weight 8.5 kg / 18.7 lbs (not including projection lens unit)

Accessories

Remote control, remote control dry-cell batteries, power cord, PC connection

cable, User’s Manual / Installation Manual (this manual), warranty certificate

Product Specifications

220

*1When using a Standard Zoom Lens (RS-IL01ST). Varies depending on the type of lens unit.

* 99.99% or more of the LCD panel pixels are effective. During projection, 0.01% or less of pixels may stay lit or unlit due to the char-

acteristics of the LCD panel.

* Using the projector continuously for an extended period of time may accelerate the deterioration of optical parts.

Model name WX6000 SX6000

Display system RGB liquid crystal system

Optical system Color separation by dichroic mirror / polarizing beam splitter and color com-

position by prism

Display device

Type Reflective liquid crystal panel

Size / Aspect ratio 0.7'' X3 / 16:10 0.72'' X3 / 4:3

Drive system Active matrix system

Number dots / Total number dots 1,296,000 (1440 x 900) x 3 panels /

3,888,000

1,470,000 (1400 x 1050) x 3 panels /

4,410,000

Projection

lens(*1)

Zoom ratio / Focal length / F value 1.5 x / f = 23.0 - 34.5 mm / F1.89 - F2.65

Zooming / Focusing system Electric / Electric

Lens shift V: -15% - +55%, H: ±10% V: -12% - +50%, H: ±10%

Light source 330-NSHA 336 W

Image size (projection distance) (*1) 40'' to 600'' (1.3 to 29.7 m) 40'' to 600'' (1.3 to 28.8 m)

Number of colors 16,770,000 colors (full color)

Brightness (*1) 5,700 lumen 6,000 lumen

Contrast ratio 1000:1 (Full white: Full black, during presentation)

Ratio of brightness at periphery to center (*1) 88%

Speaker 5W monaural x 1

Maximum input resolution 1440 x 900 dots 1400 x 1050 dots

Video signals

Analog PC input UXGA / WSXGA+ / SXGA+ / WXGA+ / WXGA / SXGA / XGA / SVGA / VGA

Digital PC input UXGA / WSXGA+ / SXGA+ / WXGA+ / WXGA / SXGA / XGA / SVGA / VGA

Digital video input 1080p, 1080i, 720p, 576p, 480p

Component video input 1080p, 1080i, 720p, 576p, 576i, 480p, 480i

Input terminal

DVI-I IN terminal Analog PC, Digital PC (24-pin DVI connector)

HDMI IN terminal Digital PC, HDMI (deep color)

ANALOG PC / COMPONENT IN terminal Analog PC, Component (mini D-sub 15-pin)

CONTROL terminal RS-232C (D-sub 9-pin)

Remote terminal Wired remote control (3.5Ø stereo mini jack)

AUDIO IN Terminal Audio signal (3.5Ø stereo mini jack x 2)

AUDIO OUT Terminal Audio signal (3.5Ø stereo mini jack)

LAN terminal Network connection (RJ-45)

Input signal

Digital PC TMDS (Transition Minimized Differential Signaling)

Analog PC

0.7Vp-p, positive polarity, impedance = 75Ω

Horizontal / vertical synchronization: TTL level, negative or positive polarity

Composite synchronization in G signal: 0.3Vp-p, negative polarity, imped-

ance = 75Ω

Component video

COMPONENT: Separate Y Cb/Pb Cr/Pr signal

Y: 1Vp-p, negative synchronization, impedance = 75Ω

Cb/Pb: 0.7Vp-p, impedance = 75Ω

Cr/Pr: 0.7Vp-p, impedance = 75Ω

Audio Impedance = 47kΩ or more

Noise 40 dB

Operating temperature 5°C - 35°C

Power supply AC100V - 240V 50 / 60Hz

Power consumption (Projection / standby /

standby with LAN OFF) 435W / 1.7W / 0.35W

Dimensions 380 mm (W) x 150 mm (H) x 430 mm (D) / 15.0 (W) x 5.9 (H) x 16.9 (D) in

(not including the projection)

Weight 8.5 kg / 18.7 lbs (not including projection lens unit)

Accessories

Remote control, remote control dry-cell batteries, power cord, PC connection

cable, User’s Manual / Installation Manual (this manual), warranty certificate

221

Product Specifications

endix Other Information

■Remote control

■Specification of Each Lens Unit (Option)

For details about the amount of lens shift, refer to page 160.

*: WUX5000 / WUX4000

Type RS-RC04 RS-RC05

Power supply DC 3.0V, using two AAA-size batter-

ies DC 3.0V, using two AA-size batteries

Operating range Approx. 8 m± 25° horizontal and vertical (to infrared remote receiver)

Dimensions

43 mm (W) x 23 mm (H) x

135 mm (D) /

1.7 (W) x 0.9 (H) x 5.3 (D) in.

51 mm (W) x 28 mm (H) x

176 mm (D) /

2.0 (W) x 1.1 (H) x 6.9 (D) in.

Weight 56 g / 2.0 oz 100 g / 3.5 oz

Name Standard Zoom Lens Long Zoom Lens

Model number RS-IL01ST RS-IL02LZ

External View

Focal length 23.0 - 34.5 mm

(0.9 - 1.4'')

34.0 - 57.7 mm

(1.3 - 2.3'')

F number 1.89 - 2.65 1.99 - 2.83

Projection distance* 1.3 - 28.8 m

(4.3 - 94.5')

1.9 - 48.3 m

(6.2 - 158.5')

Width 97.4 mm (3.8'') 97.4 mm (3.8'')

Height 106.5 mm (4.2'') 106.5 mm (4.2'')

Length 173.4 mm (6.8'') 173.4 mm (6.8'')

Weight 550 g (1.2 lbs) 755 g (1.7 lbs)

Zoom ratio 1.5x 1.7x

Size 100 projection dis-

tance*

3.2 - 4.8 m

(10.5 - 15.7')

4.7 - 8.0 m

(15.4 - 26.2')

Product Specifications

222

For details about the amount of lens shift, refer to page 160.

*: WUX5000 / WUX4000

Name Short Fixed Lens Ultra Long Zoom Lens

Model number RS-IL03WF RS-IL04UL

External View

Focal length 12.8 mm (0.5'') 53.6 - 105.6 mm (2.1 - 4.2'')

F number 2.0 2.34 - 2.81

Projection distance* 0.7 - 5.2 m

(2.3 - 17.1')

4.6 - 89.0 m

(15.1 - 292.0')

Width 97.4 mm (3.8'') 97.4 mm (3.8'')

Height 106.5 mm (4.2'') 106.5 mm (4.2'')

Length 175.2 mm (6.9'') 184.2 mm (7.3'')

Weight 910 g (2.0 lbs) 940 g (2.1 lbs)

Zoom ratio – 1.95x

Size 100 projection dis-

tance* 1.7 m (5.6') 7.6 - 14.9 m (24.9 - 48.9')

223

Product Specifications

endix Other Information

■External View

■ANALOG PC (WUX5000 / WUX4000), ANALOG PC-1 (WX6000 / SX6000) /

COMPONENT IN Terminal

This terminal is used as a computer ANALOG PC input or COMPONENT input terminal.

Use a D-sub computer cable for connection.

The terminal specifications for the ANALOG PC input and COMPONENT input are the

same.

Mini D-sub 15-pin

430mm

53mm

128mm

212mm

234.5mm

380mm

92mm

91mm

150mm

311mm

154.5mm141.5mm

Bolt holes (M4 x 6)

for installation of

ceiling attachment

430 mm (16.9'')

92 mm

(3.6'')

380 mm (15.0'')

53 mm

(2.1'') 212 mm (8.4'')

234.5 mm (9.2'')

91 mm (3.5'')

150 mm

(5.9'')

311 mm (12.2'')

141.5 mm

(5.6'')

154.5 mm

(6.1'')

128 mm (5.0'')

Pin No. Signal Pin No. Signal

1R 9+5 V power

2 G 10 Ground (Vertical

sync.)

3 B 11 Monitor ID0

4 Monitor ID2 12 DDC data

5 Ground (Horizontal

sync.)

13 Horizontal sync.

6 Ground (R) 14 Vertical sync.

7 Ground (G) 15 DDC clock

8 Ground (B)

Product Specifications

224

■Service Port (CONTROL)

Pin assignment

Communication format

Communication mode : RS-232-C, asynchronous, half-duplex communication

Communication speed : 19200bps

Character length : 8 bits

Stop bits : 2 bits

Parity : None

Flow control : None

Control commands

Commands ASCII representation Binary representation

Power supply Power on POWER ON<CR> 50h 4Fh 57h 45h 52h 20h 4Fh 4Eh 0Dh

Power off POWER OFF<CR> 50h 4Fh 57h 45h 52h 20h 4Fh 46h 46h 0Dh

Power status

acquisition GET POWER<CR> 47h 45h 54h 20h 50h 4Fh 57h 45h 52h 0Dh

Input status

(WUX5000 /

WUX4000)

DVI-D INPUT=D-RGB<CR> 49h 4Eh 50h 55h 54h 3Dh 44h 2Dh 52h 47h 42h 0Dh

HDMI INPUT=HDMI<CR> 49h 4Eh 50h 55h 54h 3Dh 48h 44h 4Dh 49h 0Dh

Analog PC INPUT=A-RGB<CR> 49h 4Eh 50h 55h 54h 3Dh 41h 2Dh 52h 47h 42h 0Dh

Component INPUT=COMP<CR> 49h 4Eh 50h 55h 54h 3Dh 43h 4Fh 4Dh 50h 0Dh

Input status

(WX6000 /

SX6000)

HDMI INPUT=HDMI<CR> 49h 4Eh 50h 55h 54h 3Dh 48h 44h 4Dh 49h 0Dh

Digital PC INPUT=D-RGB<CR> 49h 4Eh 50h 55h 54h 3Dh 44h 2Dh 52h 47h 42h 0Dh

Analog PC1 INPUT=A-RGB1<CR> 49h 4Eh 50h 55h 54h 3Dh 41h 2Dh 52h 47h 42h 31h 0Dh

Analog PC2 INPUT=A-RGB2<CR> 49h 4Eh 50h 55h 54h 3Dh 41h 2Dh 52h 47h 42h 32h 0Dh

Component INPUT=COMP<CR> 49h 4Eh 50h 55h 54h 3Dh 43h 4Fh 4Dh 50h 0Dh

Input source

acquisition GET INPUT<CR> 47h 45h 54h 20h 49h 4Eh 50h 55h 54h 0Dh

Pin No. Signal

1 OPEN

2RxD

3TxD

4 OPEN

5GND

6 OPEN

7 OPEN

8 OPEN

9 OPEN

225

Product Specifications

endix Other Information

Image mode Standard IMAGE=STANDARD<CR> 49h 4Dh 41h 47h 45h 3Dh 53h 54h 41h 4Eh 44h 41h 52h 44h

0Dh

Presentation IMAGE=PRESENTATION<CR> 49h 4Dh 41h 47h 45h 3Dh 50h 52h 45h 53h

45h 4Eh 54h 41h 54h 49h 4Fh 4Eh 0Dh

VividPhoto IMAGE=VIVID_PHOTO<CR> 49h 4Dh 41h 47h 45h 3Dh 56h 49h 56h 49h 44h 5Fh 50h 48h

4Fh 54h 4Fh 0Dh

Photo /sRGB IMAGE=PHOTO_SRGB<CR> 49h 4Dh 41h 47h 45h 3Dh 50h 48h 4Fh 54h 4Fh 5Fh 53h 52h

47h 42h 0Dh

Dynamic IMAGE=DYNAMIC<CR> 49h 4Dh 41h 47h 45h 3Dh 44h 59h 4Eh 41h 4Dh 49h 43h

0Dh

Video IMAGE=VIDEO<CR> 49h 4Dh 41h 47h 45h 3Dh 56h 49h 44h 45h 4Fh 0Dh

Cinema IMAGE=CINEMA<CR> 49h 4Dh 41h 47h 45h 3Dh 43h 49h 4Eh 45h 4Dh 41h 0Dh

Image mode User 1 IMAGE=USER_1<CR> 49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h 52h 5Fh 31h 0Dh

User 2 IMAGE=USER_2<CR> 49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h 52h 5Fh 32h 0Dh

User 3 IMAGE=USER_3<CR> 49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h 52h 5Fh 33h 0Dh

User 4 IMAGE=USER_4<CR> 49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h 52h 5Fh 34h 0Dh

User 5 IMAGE=USER_5<CR> 49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h 52h 5Fh 35h 0Dh

Image mode

acquisition GET IMAGE<CR> 47h 45h 54h 20h 49h 4Dh 41h 47h 45h 0Dh

Brightness Brightness value

setting BRI=<value><CR> 42h 52h 49h 3Dh <numeric code> 0Dh

Brightness

acquisition GET BRI<CR> 47h 45h 54h 20h 42h 52h 49h 0Dh

Sharpness Sharpness value

setting SHARP=<value><CR> 53h 48h 41h 52h 50h 3Dh <numeric code> 0Dh

Sharpness

acquisition GET SHARP<CR> 47h 45h 54h 20h 53h 48h 41h 52h 50h 0Dh

Contrast Contrast value

setting CONT=<value><CR> 43h 4Fh 4Eh 54h 3Dh <numeric code> 0Dh

Contrast

acquisition GET CONT<CR> 47h 45h 54h 20h 43h 4Fh 4Eh 54h 0Dh

Aspect

(WUX5000 /

WUX4000)

Auto ASPECT=AUTO<CR> 41h 53h 50h 45h 43h 54h 3Dh 41h 55h 54h 4Fh 0Dh

4:3 ASPECT=4:3<CR> 41h 53h 50h 45h 43h 54h 3Dh 34h 3Ah 33h 0Dh

16:9 ASPECT=16:9<CR> 41h 53h 50h 45h 43h 54h 3Dh 31h 36h 3Ah 39h 0Dh

Zoom ASPECT=ZOOM<CR> 41h 53h 50h 45h 43h 54h 3Dh 5Ah 4Fh 4Fh 4Dh 0Dh

True size ASPECT=TRUE<CR> 41h 53h 50h 45h 43h 54h 3Dh 54h 52h 55h 45h 0Dh

Full ASPECT=FULL<CR> 41h 53h 50h 45h 43h 54h 3Dh 46h 55h 4Ch 4Ch 0Dh

Aspect

(WX6000 /

SX6000)

Auto ASPECT=AUTO<CR> 41h 53h 50h 45h 43h 54h 3Dh 41h 55h 54h 4Fh 0Dh

4:3 ASPECT=4:3<CR> 41h 53h 50h 45h 43h 54h 3Dh 34h 3Ah 33h 0Dh

16:9 ASPECT=16:9<CR> 41h 53h 50h 45h 43h 54h 3Dh 31h 36h 3Ah 39h 0Dh

16:10 ASPECT=16:10<CR> 41h 53h 50h 45h 43h 54h 3Dh 31h 36h 3Ah 31h 30h 0Dh

Zoom ASPECT=ZOOM<CR> 41h 53h 50h 45h 43h 54h 3Dh 5Ah 4Fh 4Fh 4Dh 0Dh

True size ASPECT=TRUE<CR> 41h 53h 50h 45h 43h 54h 3Dh 54h 52h 55h 45h 0Dh

Aspect value

acquisition GET ASPECT<CR> 47h 45h 54h 20h 41h 53h 50h 45h 43h 54h 0Dh

Lamp mode Normal LAMP=NORMAL<CR> 4Ch 41h 4Dh 50h 3Dh 4Eh 4Fh 52h 4Dh 41h 4Ch 0Dh

Quiet LAMP=SILENT<CR> 4Ch 41h 4Dh 50h 3Dh 53h 49h 4Ch 45h 4Eh 54h 0Dh

Lamp mode

value acqui-

sition

GET LAMP<CR> 47h 45h 54h 20h 4Ch 41h 4Dh 50h 0Dh

Commands ASCII representation Binary representation

Product Specifications

226

Blank Blank On BLANK=ON<CR> 42h 4Ch 41h 4Eh 4Bh 3Dh 4Fh 4Eh 0Dh

Blank Off BLANK=OFF<CR> 42h 4Ch 41h 4Eh 4Bh 3Dh 4Fh 46h 46h 0Dh

Blank acqui-

sition GET BLANK<CR> 47h 45h 54h 20h 42h 4Ch 41h 4Eh 4Bh 0Dh

Commands ASCII representation Binary representation

227

Product Specifications

endix Other Information

228

Index

Numerics

6-axis color adjust ............................... 117

Adjusting Keystone Distortion .............. 76

Adjusting the focus ............................... 73

Adjusting the Volume ............................ 83

Air filter ................................................ 193

Ambient light ....................................... 115

Analog PC ............................... 47, 59, 164

ANALOG PC / COMPONENT IN

terminal (WUX5000 /

WUX4000) ........ 40, 47, 49, 53, 59, 164

Analog PC-1 (WX6000 / SX6000) ... 47, 48

Analog PC-1 / COMPONENT IN

terminal (WX6000 /

SX6000) ............ 41, 48, 49, 54, 59, 164

Analog PC-2 (WX6000 / SX6000) ......... 48

Analog PC-2 / DVI-I IN terminal (WX6000 /

SX6000) .......................... 41, 48, 50, 59

ASPECT ................................................ 70

Aspect .............................. 63, 69, 93, 207

AUDIO IN

terminal ............ 40, 41, 47, 50, 53, 139

AUDIO OUT terminal .......... 40, 41, 51, 55

Auto (Aspect) ........................................ 69

AUTO PC .............................................. 62

Beep ................................................... 122

BLANK .................................................. 82

Brightness ........................................... 111

Ceiling mounted .................................. 104

Channel setting ................................... 124

Component ....................... 53, 59, 95, 164

Connection to Computer ....................... 47

Contrast .............................................. 112

D. ZOOM ............................................... 84

D.SHIFT / KEYSTONE

(WUX5000 / WUX4000) ........ 67, 68, 76

DHCP .................................................. 175

Digital Image Shift ................................. 67

Digital PC ................................ 50, 59, 164

Direct power on .................................. 121

Display Resolution (Preparing the Comput-

er) ..................................................... 61

Display settings menu .......................... 88

Displaying logo ................................... 106

DVI .......................................... 50, 59, 164

DVI-D IN (WUX5000 / WUX4000) ......... 50

DVI-D IN terminal

(WUX5000 / WUX4000) .................... 40

DVI-I IN (WX6000 / SX6000) ........... 48, 50

DVI-I IN terminal (WX6000 / SX6000) ... 41

Dynamic gamma ................................. 116

Factory defaults .................................. 140

FOCUS .................................................. 73

FREEZE ................................................. 82

Guide .................................................. 126

HDMI ................................. 51, 52, 59, 164

HDMI color space ................................. 99

HDMI IN terminal ................ 40, 41, 51, 52

HDMI input level ................................... 98

HDMI over scan .................................. 100

Horizontal pixels ................................... 97

Horizontal position ................................ 96

IMAGE ................................................... 79

Image adjustment menu ................. 88, 89

Image flip H/V (Ceiling mounted /

Rear projection) .............................. 104

Image mode ........................................ 109

229

Index

endix Index

Image Mode (Image Quality) ................78

Information ..............................88, 89, 141

INPUT ....................................................60

Input settings (WX6000 / SX6000) ........89

Input signal select .....................59, 94, 95

Input Terminal .......................................40

Connecting to AV Equipment ............52

Connection to Computer ................... 47

Install settings (WX6000 / SX6000) ....... 89

Key lock ..............................................123

Keystone ...............................................76

KEYSTONE (WX6000 / SX6000) ...........76

LAMP (WUX4000) ...............................119

Lamp counter ......................................135

Lamp mode (WUX4000) ..................... 119

Lamp replacement ..............135, 195, 196

LAN port ..........................................40, 41

Language ............................................ 125

LED indicator ......................................202

Memory Color Correction ....................117

MENU .............................................. 88, 89

Menu display time ............................... 132

Menu position ...................................... 102

MUTE ....................................................83

Network function .................................172

Network Password setting ..................173

Network setting ............................... 88, 89

Network setting initialization ................176

Network setting lock ............................ 171

Noise reduction ...................................116

OK ...................................................35, 36

Password settings ...............................128

Performing Gamma Correction ...........113

PJLink ..................................................174

Positional lock (WX6000 / SX6000) .....139

POWER ...................................56, 80, 121

Power Management ..............................57

Power management mode (settings) ..120

Power Saving (Power Management) .....57

Progressive .........................................101

Projector on .........................................106

P-TIMER (WUX5000 / WUX4000) ..........85

Rear projection ....................................104

Remote control ..................29, 34, 36, 124

Reset ...........................................119, 140

Screen aspect .......................63, 107, 207

Screen color ........................................103

Screen When Blank .............................106

Selecting a language ....................57, 125

Selecting an Image Quality .................109

Setting Display Status ...........................93

Setting Various Functions ....................120

Sharpness ...........................................113

Side Control ...........................................38

Signal type ..........................................218

System settings menu .....................88, 89

TCP/IP settings ....................................175

Test pattern

(WX6000 / SX6000) .................138, 217

Total dots ...............................................95

Tracking .................................................96

True size (Aspect) .................................69

Turning on external monitor output (prepar-

ing the notebook computer) .............58

Index

230

Vertical pixels ........................................ 98

Vertical Position .................................... 97

VOL ....................................................... 83

WARNING indicator ...................... 38, 202

ZOOM ................................................... 71

Zoom (Aspect) ...................................... 69

Zooming an Image ................................ 84

231

Option

• Installing / Removing the Lens Unit

It is possible to use replace the lens unit. Regarding installation and replacement of the lens unit, con-

tact a qualified technician or the Canon Customer Support Center for further information. Do not

attempt installation and replacement of the lens unit yourself.

• Precaution for qualified technicians

Before installation and replacement the lens unit, check the part number and use the correct lens unit.

•Lamp

Part No.: RS-LP06 (WUX4000)

RS-LP07 (WUX5000 / WX6000 /

SX6000)

• Air filter

Part No.: RS-FL01

• Standard Zoom Lens

Part No.: RS-IL01ST

• Ceiling attachment

Part No.: RS-CL11

• Long Zoom Lens

Part No.: RS-IL02LZ

• Ceiling-mount pipe (400 - 600 mm)

Part No.: RS-CL08*

• Short Fixed Lens

Part No.: RS-IL03WF

• Ceiling-mount pipe (600 - 1000 mm)

Part No.: RS-CL09*

• Ultra Long Zoom Lens

Part No.: RS-IL04UL

• Black top panel

Part No.: RS-TC01

• Remote control

Part No.: RS-RC04 (WUX5000 / WUX4000)

RS-RC05 (WX6000 / SX6000)

* Use the above materials to hang the projector from the ceiling. For details, refer to the assembly and

installation manual provided with the ceiling attachment RS-CL11.

232

Menu Configuration

Display settings Menu

Aspect Digital PC / Analog PC

P93

Auto *

Full

16:9

4:3

True size

HDMI

Auto *

Full

16:9

4:3

Zoom

True size

Component

Auto *

16:9

4:3

Zoom

True size

Input signal

select Analog PC

P94

640x480

1920x1200

Component

P95

Auto *

1080p

1080i

1035i

720p

576p

480p

576i

480i

Input signal

settings Analog PC

Total dots P95

Tracking P96

Horizontal position P96

Vertical position P97

Horizontal pixels P97

Vertical pixels P98

HDMI input level HDMI P98

Auto *

Normal

Expanded

HDMI color space

HDMI

P99

Auto *

RGB

YCbCr

HDMI over scan *1

HDMI P100

Off

Progressive Component / HDMI

P101

Off

Auto *

Menu position P102

Screen color Normal *

P103

Greenboard

Adjust Red /

Green / Blue

Image flip H/V None *

P104

Ceiling mounted

Rear

Rear, Ceiling mounted

User screen

settings

No signal screen Black

P105

Blue*

Screen when blank Black *

P106

Blue

Projector on Skip

P106

Canon logo*

Return

Screen aspect 16:10*

P107

16:9

4:3

16:9 D. image shift

4:3 D. image shift

233

Menu Configuration

Image Adjustment Menu

Factory default settings for *1, *2 and *3 are set accord-

ing to the following conditions.

*1: • For Analog PC, Digital PC or HDMI (when [HDMI

In] is [Computer]), the factory default is [Off].

• For Component, and HDMI (when [HDMI In] is

[Auto]), the factory default is [On].

*2: • For HDMI (when [HDMI In] is [Auto]), the factory

default is [Off].

• For Component, the factory default is [Weak].

*3: • For HDMI (when [HDMI In] is [Computer]), Digi-

tal PC or Analog PC, if any image mode is used

except [VividPhoto], the factory default is [Off].

If [VividPhoto] is used, the factory default is

[Middle].

• For HDMI (when [HDMI In] is [Auto]) or Compo-

nent, the factory default is [Weak], regardless of

the image mode.

*4: • WUX4000

Image mode COMMON

P109

Standard *

Photo/sRGB

User 1 - 5 (as creating

profile)

Digital PC / Analog PC /

HDMI (when [HDMI In]

is [Computer])

P109

Presentation

VividPhoto

Component / HDMI

(when [HDMI In] is [Auto]) P109

Dynamic

Video

Cinema

Create Profile P110

Baseline Image

Mode (when user

memory is selected)

P110

Brightness P111

Contrast P112

Sharpness P113

Gamma P113

Color adjustment P114

Color level

Color balance

Color temperature

R Gain

G Gain

B Gain

R Offset

G Offset

B Offset

Advanced adjustment

Ambient light Off *

P115

Adjust

Type Tungsten

Fluorescent

Fluores-

cent H

Level L

Return

Noise reduction *2 Component / HDMI

P116

Off

Weak

Middle

Strong

Dynamic gamma Off *1

P116

Weak *2

Middle

Strong

Mem. color correct *3

Off

P117

6-axis color adjust Off *

P117

Adjust

Hue / Saturation /

Brightness

Reset

Fine-Tune Gamma P118

Return

Lamp mode *4 Normal *

P119

Quiet

Reset OK / Cancel

P119

Menu Configuration

234

System Settings Menu

Network Setting Menu

Information Menu

*: Factory defaults (setting after reset)

Power management

mode Off *

P120

Standby

Exit

Direct power on Off *

P121

Beep Off

P122

On *

Key lock Off *

P123

Main unit

Remote control

Remote control Ch1

P124

Ch2

Ch3

Ch4

Independent *

Language

English Turkish

P125

German Polish

French Hungarian

Italian Czech

Spanish Danish

Portuguese Arabic

Swedish Chinese

(Simplified)

Russian Chinese

(Traditional)

Dutch Korean

Finnish Japanese

Norwegian

Guide Off P126

On *

Show Input Status Off

P127

On *

HDMI In

Auto *

P127

Computer

Other settings

Password settings Off *

P128

P129

Lens Ctrl Lock Off *

P130

Lens shift Reset Lens shift Reset

P131

Menu display time Normal *

P132

Extended

Overheat Warning Dis-

play Off *

P133

Deflicker Off *

P134

Adjust

Lamp counter Return

P135

Reset (OK / Cancel)

Factory defaults OK / Cancel

P140

Return

Network setting lock Unlock

P171

Lock *

Network function Off *

P172

Network Password setting Off

P173

On *

word Password input

P173

PJLink Off

P174

On *

DHCP Off *

P175

TCP/IP setting IP address

P175

Subnet mask

Gateway address

Enter

Network setting initializa-

tion Yes / No

P176

Model name

P141

Input signal

Firmware

Serial No.

IP address

Gateway address

E-mail sender address

E-mail recipient address

Projector name

Location

System information ID

235

Menu Configuration

Input Settings Menu

Aspect

Digital PC / Analog PC-1 / 2 /

HDMI (when [HDMI In] is

[PC])

P93

Auto *

16:10

16:9

4:3

True size

HDMI (when [HDMI In] is

[Auto]) /Component

Auto *

16:10

16:9

4:3

Zoom

True size

Auto PC P94

Input signal

select Analog PC-1 / 2 P94

640 x 480

1920 x1200

Input signal set-

tings Analog PC-1 / 2

Total dots P95

Tracking P96

Horizontal position P96

Vertical position P97

Horizontal pixels P97

Vertical pixels P98

HDMI input level HDMI

P98

Auto *

Normal

Expanded

HDMI color

space HDMI P99

Auto *

RGB

YCbCr

HDMI over

scan*1 HDMI

P100

Off

Progressive Component / HDMI P101

Off

Auto *

Menu Configuration

236

Image Adjustment Menu

Image mode COMMON P109

Standard *

Photo/sRGB

User 1 - 5 (when creating

profile)

Digital PC /

Analog PC-1/2 /

HDMI (when [HDMI In] is

[Computer])

P109

Presentation

VividPhoto

Component / HDMI (when

[HDMI In] is [Auto]) P109

Dynamic

Video

Cinema

Create Profile P110

Save profile

(When profile is

selected)

P110

Baseline Image

Mode (When pro-

file is selected)

P111

Brightness P111

Contrast P112

Sharpness P113

Gamma P113

Color adjustment P114

Color level

Color balance

Color temperature

R Gain

G Gain

B Gain

R Offset

G Offset

B Offset

Advanced adjustment

Ambient light Off *

P115

Adjust

Type Tungsten

Fluorescent

Level L

Return

Noise reduction *2 Component / HDMI

P116

Off

Weak

Middle

Strong

Dynamic gamma Off *1

P116

Weak *2

Middle

Strong

Mem. color correct *3

Off

P117

6-axis color adjust Off *

P117

Adjust

Hue / Saturation /

Brightness

Reset

Fine-Tune Gamma

P118

Return

Reset OK / Cancel

P119

237

Menu Configuration

Install settings Menu

*1 - *5: Factory default settings are set according to the

following conditions.

*1: • For Analog PC-1/2, Digital PC or HDMI (when

[HDMI In] is [Computer]), the factory default is

[Off].

• For Component, and HDMI (when [HDMI In] is

[Auto]), the factory default is [On].

*2: • For HDMI (when [HDMI In] is [Auto]), the factory

default is [Off].

• For Component, the factory default is [Weak].

*3: • For HDMI (when [HDMI In] is [Computer]), Digi-

tal PC or Analog PC-1/2, if any image mode is

used except [VividPhoto], the factory default is

[Off]. If [VividPhoto] is used, the factory default

is [Middle].

• For HDMI (when [HDMI In] is [Auto]) or Compo-

nent, the factory default is [Weak], regardless of

the image mode.

*4: • SX6000

*5: • WX6000

Positional lock Off * P139

Test pattern Off * P138

Screen aspect 16:10 *5 P107

16:9

4:3 *4

16:10 D. image shift

(SX6000)

16: 9 D. image shift

4:3 D. image shift

(WX6000)

Keystone adjustment

Keystone adjustment P108

Digital image shift D. image shift adjustment P108

Image flip H/V None* P104

Ceiling mounted

Rear

Rear, Ceiling mounted

Lens shift reset Lens shift reset P131

Audio in terminal select

HDMI Off P139

Audio in 1

Audio in 2

HDMI *

Digital PC Off P139

Audio in 1

Audio in 2 *

Analog PC-1 Off P139

Audio in 1 *

Audio in 2

Analog PC-2 Off P139

Audio in 1

Audio in 2 *

Component Off P139

Audio in 1 *

Audio in 2

Screen color Normal * P103

Greenboard

Adjust

On screen

Menu position P102

Guide Off P126

On *

Show input status Off P127

On *

Overheat warning display

Off * P133

Menu display time Normal * P132

Extended

Lamp warning display Off P135

On *

Filter warning display Off P137

On *

Menu Configuration

238

System Settings Menu

Network Setting Menu

Information Menu

*: Factory defaults (setting after reset)

Power management mode

Off * P120

Standby

Exit

Direct power on Off * P121

User screen settings

No signal screen Black P105

Blue *

Screen when blank Black * P106

Blue

Projector on Skip P106

Canon logo *

Beep Off P122

On *

Key Repeat Off P122

On *

Key lock Off * P123

Main unit

Remote (wireless)

Remote control Ch1 P124

Ch2

Ch3

Ch4

Independent*

HDMI In Auto * P127

Computer

Language

English Turkish

P125

German Polish

French Hungarian

Italian Czech

Spanish Danish

Portuguese Arabic

Swedish Chinese

(Simplified)

Russian Chinese

(Traditional)

Dutch Korean

Finnish Japanese

Norwegian

Other settings

Password settings Off * P128

Gamma restore Off P134

Adjust

Lamp counter Return P135

Reset (OK / Cancel)

Filter counter Return P137

Reset (OK / Cancel)

Factory defaults OK / Cancel P140

Return

Network setting lock Unlock

P171

Lock *

Network function Off *

P172

Network Password setting Off

P173

On *

word Password input

P173

PJLink Off

P174

On *

DHCP Off *

P175

TCP/IP setting IP address

P175

Subnet mask

Gateway address

Enter

Network setting initializa-

tion Yes / No

P176

Model name P141

Input signal

Firmware

Serial No.

IP address

Gateway address

E-mail sender address

E-mail recipient address

Projector name

Location

System information ID

239

Menu Configuration

CANON INC.

30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo

146-8501, Japan

U.S.A.

CANON U.S.A. INC.

One Canon Plaza, Lake Success, NY 11042-

1198, U.S.A.

For all inquires concerning this product, call toll

free in the U.S. 1-800-OK-CANON

CANADA

CANON CANADA INC. HEADQUARTERS

6390 Dixie Road, Mississauga, Ontario L5T

1P7, Canada

CANON CANADA INC. MONTREAL BRANCH

5990, Côte-de-Liesse, Montréal Québec H4T

1V7, Canada

CANON CANADA INC. CALGARY OFFICE

2828, 16th Street, N.E. Calgary, Alberta T2E

7K7, Canada

For all inquiries concerning this product, call toll

free in Canada

1-800-OK-CANON

EUROPE, AFRICA & MIDDLE EAST

CANON EUROPE LTD.

3 The Square Stockley Park, Uxbridge, Middle-

sex, UB11 1ET United Kingdom

CANON EUROPA N.V.

Bovenkerkerweg 59-61, 1185 XB Amstelveen,

The Netherlands

CANON FRANCE S.A.S

17, quai du President Paul Doumer, 92414

Courbevoie Cedex, France

CANON UK LTD.

Woodhatch Reigate Surrey RH2 8BF, United

Kingdom

CANON DEUTSCHLAND GmbH

Europark Fichtenhain A10, 47807 Krefeld, Ger-

many

CANON ITALIA S.p.A.

Via Milano 8 I-20097 San Donato Milanese, Mil-

ano, Italy

CANON Schweiz AG

Geschäftsbereich Wiederverkauf, Industri-

estrasse 12, CH-8305 Dietlikon,

Switzerland

CANON GMBH

Zetschegasse 11, A-1230 Wien, Austria

CANON España, S.A.

Av. De Europa, 6 Alcobendas 28108 Madrid,

Spain

CANON PORTUGAL S.A.

Rua Alfredo da Silva, 14 Alfragide 2610-016

Amadora, Portugal

CANON Belgium N.V. / S.A.

Berkenlaan 3, 1831 Diegem (Mechelen), Bel-

gium

CANON Netherland NV

Neptunusstraat 1, 2132 JA Hoofddorp, The

Netherlands

CANON LUXEMBOURG S.A.

Rue des Joncs 21, L-1818 Howald, Luxem-

bourg

CANON DANMARK A / S

Knud Hoejgaards Vej 1 DK-2860 Soeborg, Dan-

mark

CANON OY

Huopalahdentie 24 PL 1 00351 Helsinki, Fin-

land

CANON SVENSKA AB

Gustav III:s Boulevard 26 169 88 Solna, Swe-

den

CANON NORGE as

Hallagerbakken 110, Postboks 33, Holmlia,

1201 Oslo, Norway

CENTRAL & SOUTH AMERICA

CANON LATIN AMERICA, INC.

703 Waterford Way, Ste. 400 Miami, FL 33126,

U.S.A.

ASIA

CANON (China) Co., Ltd.

15F Jinbao Building No.89 Jinbao Street,

Dongcheng District, Beijing 100005, China

CANON HONGKONG CO., LTD.

19 / F., The Metropolis Tower, 10 Metropolis

Drive, Hunghom, Kowloon, Hong Kong

CANON SINGAPORE PTE. LTD.

1 HarbourFront Avenue, #04-01 Keppel Bay

Tower, Singapore 098632

CANON KOREA CONSUMER IMAGING INC.

Canon BS Tower 5F, #168-12 Samseong-dong,

Gangnam-gu, Seoul, Korea

OCEANIA

CANON AUSTRALIA PTY. LTD.

1 Thomas Holt Drive, North Ryde, N.S.W. 2113,

Australia

CANON NEW ZEALAND LTD.

Akoranga Business Park, Akoranga Drive,

Northcote, Auckland, New Zealand