Chief Impact User Manual

Displayed below is the user manual for Impact by Chief which is a product in the Monitor Mounts & Stands category. This manual has pages.

Related Manuals

Chief Impact Manual

INSTALLATION INSTRUCTIONS

40"/42"/43" Portrait Wall Kiosks

Spanish Product Description

German Product Description

Portuguese Product Description

Italian Product Description

Dutch Product Description

French Product Description

LW40/42/43UxP

LW40/42/43UxPG

LW40/42/43UxP LW40/42/43UxPG Installation Instructions

DISCLAIMER

Legrand | AV and its affiliated corporations and subsidiaries

(collectively “Legrand | AV”), intend to make this manual

accurate and complete. However, Legrand | AV makes no claim

that the information contained herein covers all details,

conditions or variations, nor does it provide for every possible

contingency in connection with the installation or use of this

product. The information contained in this document is subject

to change without notice or obligation of any kind. Legrand | AV

makes no representation of warranty, expressed or implied,

regarding the information contained herein. Legrand | AV

assumes no responsibility for accuracy, completeness or

sufficiency of the information contained in this document.

Chief® is a registered trademark of Legrand AV Inc.

DEFINITIONS

MOUNTING SYSTEM: A MOUNTING SYSTEM is the

primary Chief product to which an accessory and/or component

is attached.

ACCESSORY: AN ACCESSORY is the secondary Chief

product which is attached to a primary Chief product, and may

have a component attached or setting on it.

COMPONENT: A COMPONENT is an audiovisual item

designed to be attached or resting on an accessory or mounting

system such as a video camera, CPU, screen, display,

projector, etc.

WARNING: A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the

corresponding instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,

damage to equipment, or voiding of factory warranty! It is the

installer’s responsibility to make sure all mounting systems

are properly assembled and installed using the instructions

provided.

WARNING: Failure to provide adequate structural strength

for this mounting system can result in serious personal injury

or damage to equipment! It is the installer’s responsibility to

make sure the structure to which this mounting system is

attached can support five times the combined weight of all

equipment. Reinforce the structure as required before

installing the mounting system.

WARNING: Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the weight of

components attached to swing door does not exceed:

•LW40/42/43UxP Models: 100 lbs (45.4 kg)

Removable storage panel capacity: 5 lbs (2.3 kg)

•LW40/42/43UxPG Models: 85 lbs (38.6 kg)

Removable storage panel capacity: 5 lbs (2.3 kg)

The hinge-open position is for installation and service only.

WARNING: Use this mounting system only for its intended

use as described in these instructions. Do not use

attachments not recommended by the manufacturer.

WARNING: Never operate this mounting system if it is

damaged. Return the mounting system to a service center for

examination and repair.

WARNING: Do not use this mounting system outdoors.

IMPORTANT ! :

The LW40/42/43UxP and LW40/42/43UxPG

portrait wall kiosks are designed to be mounted to:

• a bare 8" concrete or 8"x8"x16" concrete block wall; or

• a 2" x 4" wood studs (16" on center maximum) wall with

a maximum drywall thickness of 5/8"; or

• a steel stud (16" on center maximum) wall with a

maximum drywall thickness of 5/8"; or

• a 3/4" thickness plywood-backed, wood or steel stud

wall (24" on center) covered with drywall having a

maximum thickness of 5/8".

NOTE: The kiosks have an adjustable depth of 3" to 5".

NOTE: LW40/42/43UxPG Models ONLY: Available monitor

space reduced by 0.25" (6.25mm) for kiosks with glass

installed.

--SAVE THESE INSTRUCTIONS--

Installation Instructions LW40/42/43UxP LW40/42/43UxPG

DIMENSIONS

43.00

1092.2

26.00

660.4

19.60

497.8

LW40UxP / LW40UxPG

DIMENSIONS: INCHES

[MILLIMETERS]

43.00

1092.2

26.00

660.4

20.40

518.2

LW42UxP / LW42UxPG

DIMENSIONS: INCHES

[MILLIMETERS]

LW40/42/43UxP LW40/42/43UxPG Installation Instructions

DIMENSIONS--continued

LEGEND

43.00

1092.2

26.00

660.4

20.90

530.9

LW43UxP / LW43UxPG

DIMENSIONS: INCHES

[MILLIMETERS]

Phillips Screwdriver

Destornillador Phillips

Kreuzschlitzschraubendreher

Chave de fendas Phillips

Cacciavite a stella

Kruiskopschroevendraaier

Tournevis à pointe cruciforme

Open-Ended Wrench

Llave de boca

Gabelschlüssel

Chave de bocas

Chiave a punte aperte

Steeksleutel

Clé à fourche

Drill Hole

Perforar

Bohrloch

Fazer furo

Praticare un foro

Gat boren

Percez un trou

Hex-Head Wrench

Llave de cabeza hexagonal

Sechskantschlüssel

Chave de cabeça sextavada

Chiave esagonale

Zeskantsleutel

Clé à tête hexagonale

Installation Instructions LW40/42/43UxP LW40/42/43UxPG

TOOLS REQUIRED FOR INSTALLATION

PARTS

7/32" (wood studs)

1/2"

5/32" (security)

5/16" (concrete)

1/2" (steel studs)

[included]

Hardware Bag -

Wall Hardware Hardware Bag - Monitor Interface Hardware

Hardware Bag -

Security/Swap Hardware

AA (8)

5/16 x 2-1/2"

AB (8)

5/16"

AC (4)

1/4-20

SnapToggle

AD (4)

AE (4)

1/4-20 x 1-3/4"

1/4"

BA (4)

M4 x 12mm

BD (4)

M5 x 12mm

BG (4)

M6 x 12mm

BJ (4)

M8 x 12mm

BB (4)

M4 x 25mm BC (4)

M4 x 50mm

BE (4)

M5 x 25mm BF (4)

M5 x 50mm

BH (4)

M6 x 25mm

BI (4)

M6 x 50mm

BK (4)

M8 x 25mm

BL (4)

M8 x 50mm

BM (8)

.750x.344x.500"

BO (4)

[universal

washer]

5/32"

(security)

CA (1)

10-24 x 3/8"

CB (4)

10-32 x 3/4"

CC (4)

10-32 x 5/16"

A (1)

[Enclosure assembly]

(LW40UxP shown

as example)

BN (8)

.750x.323x.250"

AF (8)

UX10x60R

CD (4)

10-24 x 2-3/4"

NOTE: Letters match markings on hardware bags

CE (4)

10-24 x 3-1/2"

[not used]

B (1 roll)

[1/2" wide

gasket strip]

LW40/42/43UxP LW40/42/43UxPG Installation Instructions

ASSEMBLY AND INSTALLATION

Preparing Wall Bracket

1. Remove kiosk (A) from the packaging and place on a flat surface. (See Figure 1)

2. Open so that wall bracket is at a 90° angle from the swing door.

3. Keeping the wall bracket at 90°, slide the wall bracket about 1 inch towards bottom of kiosk until hinge pins clear the hinges, and

move the wall bracket away from the swing door. (See Figure 1)

Figure 1

Wall bracket

Swing door

(A)

NOTE: The kiosks ship with the removable storage panel

already in place in the lower of two mounting positions.

The panel may be removed to add components as

required, and then reinstalled in either location. (See

instructions included with the panel.)

The storage panel latch is spring-loaded. To remove

the panel, squeeze the latch on end tabs and slide the

panel sideways out of the slots on the wall bracket.

Pivot the panel and remove it from the slots on the

opposite side.

Install AV component(s) to the panel using the

hardware and instructions included with the

component(s). Either screws or cable ties may be

used to fasten component(s) to the panel.

To reinstall the panel, slide the panel end without

latches sideways into the slots on one side of the wall

bracket opening. Pivot panel in and slide it sideways

toward the slots on opposite side of the wall bracket

panel opening. The panel will snap into the slots,

securing it to the wall bracket.

IMPORTANT ! : The kiosks ship with the hinge located

on the left side. The hinge location may be switched, if

required, for installation or service. Before beginning

the installation, decide on which side the hinge should

be located and, if you require the kiosk be hinged on the

right side, switch the hinge before completing any other

installation steps. See Switching Hinge Location

section in Appendix.

Locate Mounting Site

WARNING:

IMPROPER INSTALLATION CAN LEAD TO

MOUNT FALLING CAUSING SEVERE PERSONAL INJURY

OR DAMAGE TO EQUIPMENT! It is the installers responsibility

to make certain the structure to which the mount is being

attached is capable of supporting five times the combined

weight of all

components attached to swing door

•LW40/42/43UxP Models: 100 lbs (45.4 kg)

Removable storage panel capacity: 5 lbs (2.3 kg).

(See Figure 2)

•LW40/42/43UxPG Models: 85 lbs (38.6 kg)

Removable storage panel capacity: 5 lbs (2.3 kg).

(See Figure 2)

Figure 2

LW40/42/43UxP Models

Weight Capacity:

5 lbs (2.3kg)

Removable storage panel

Installation Instructions LW40/42/43UxP LW40/42/43UxPG

Installing Wall Bracket

The LW40/42/43UxP and LW40/42/43UxPG wall kiosk mounts

are designed to be mounted to:

• a bare 8" concrete or 8"x8"x16" concrete block wall; or

• a 2" x 4" wood studs (16" on center minimum) wall with

a maximum drywall thickness of 5/8"; or

• a steel stud (16" on center minimum to 24" on center

maximum) wall with a maximum drywall thickness of

5/8".

Table 1: Fastener Information

1. Determine the horizontal center of the wall bracket, and

where it should be located on the wall. (See Figure 3)

• For wood or steel stud walls, use a level and mark the

two uppermost locations over studs for attachment a

minimum of 16" apart and a maximum of 24" apart.

(See Figure 3)

IMPORTANT ! : For maximum stability in a wood or steel

stud wall, mount the hinge side of kiosk as close as

possible to a stud.

• For concrete walls, use a level and mark the two

uppermost locations for attachment as far apart as

possible to provide maximum stability. (See Figure 3)

Figure 3

2. Drill one pilot hole (see Table 1 for size) at both locations

marked in Step 1 (See Figure 3) and follow fastener

information (appropriate for wall type) located in Table 1.

IMPORTANT ! : Refer to Fastener Installation Methods

(located in Appendix at end of Installation Instructions)

for details on installing product into various wall types.

WALL

TYPE

PILOT

HOLE

FASTENERS (see PARTS

drawing)

Steel

stud /

Wood

stud

1/2"

7/32"

- 1/4-20 x 1-3/4" Phillips screw (AD)

- 1/4" washer (AE)

- 1/4-20 Snap toggler (AC)

- 5/16 x 2-1/2" hex head lag (AA)

- 5/16" washer (AB)

Concrete 5/16 x 3-1/4" - 5/16 x 2-1/2" hex head lag (AA)

- 5/16" washer (AB)

- Fischer Anchor UX10x60R (AF)

x 2

Wall

bracket

Uppermost attachment area

Center wall bracket over desired location on wall

LW40/42/43UxP LW40/42/43UxPG Installation Instructions

IMPORTANT ! : Attaching the wall bracket requires a

minimum of 8 wall fasteners. For installation in a wood or

steel stud applications, the snap toggles are required

near the edge of the wall bracket hinge side if the hinge

side is not fastened to a stud. (See Figure 4) and (See

Figure 5)

Figure 4

3. Partially install fasteners into wall, but do not completely

tighten to wall.

4. Hang wall bracket, aligning upper mounting slot clearance

holes over fasteners and adjust side-to-side for proper

location. (See Figure 4)

5. Tighten fasteners to secure wall bracket to wall at upper

mounting slots.

6. Drill six remaining pilot holes (see Table 1 for size) at

attachment locations and follow fastener information

(appropriate for wall type) located in Table 1. (See Figure 4)

7. Tighten six fasteners to secure wall bracket to wall at middle

and lower mounting slots.

8. For Wood and Steel Stud walls: Insert four snap toggles

and related fasteners into hinge side of wall bracket. (See

Figure 5)

IMPORTANT ! : Refer to Fastener Installation Methods

(located in Appendix at end of Installation Instructions)

for details on installing snap toggles and related

fasteners into various wall types.

Figure 5

Attaching Flat Panel

1. Remove and SAVE four Phillips screws, loosen four thumb

nuts and remove hinged frame from swing door. (See

Figure 6)

Figure 6

x 2

[16" on-center attachment

shown as example only]

Clearance

holes

Mounting

slots

Insert snap-toggles at arrows

[For Wood and Steel Stud Walls Only]

x 4

Thumb

nut

Hinged

frame

Swing

door

Installation Instructions LW40/42/43UxP LW40/42/43UxPG

2. Clean the inside edge of the swing door (approximately one

inch depth around entire opening) with an alcohol wipe or

something similar, and let dry. (See Figure 7)

3. Install gasket strip (B) around inside edge of swing door

opening. (See Figure 7)

NOTE: Do not install gasket strip right up to edge. The gasket

strip should be placed approximately 1/16" away from

opening.

Figure 7

4. Carefully lay flat panel face down into the depth-adjustable

outer frame. (See Figure 8)

Figure 8

5. Center flat panel on opening within outer frame in both

vertical and horizontal directions.

NOTE: Measuring from inside edges to display edges assists

in centering the display within opening.

WARNING: IMPROPER INSTALLATION CAN LEAD TO

DISPLAY FALLING CAUSING SERIOUS PERSONAL

INJURY OR DAMAGE TO EQUIPMENT! Using screws of

improper size may damage your display. Properly sized

screws will easily and completely thread into display

mounting holes. If spacers are required, be sure to use longer

screws of the same diameter.

6. Select screw diameter by examining hardware (BA-BL) and

comparing with mounting holes on flat panel.

7. Select spacers:

• Spacers are NOT required if mounting holes are not

recessed and hinged frame can lay flat against flat

panel.

•Spacers (BM, BN) ARE required if mounting holes are

recessed, or if protrusions prevent hinged frame from

laying flat.

• Spacers may also be used between the hinged frame

and flat panel to create more space for AV

components, or to accommodate thinner flat panels.

(See Depth Adjustment section for further

information.)

8. Select screw length:

• By hand, insert SHORTEST length screw of selected

diameter (BA, BD, BG, or BJ) through universal washer

(BO--if required), hinged frame, spacer (BM, BN--if

required), into flat panel mounting hole. Do NOT thread

screw into hole at this time.

IMPORTANT ! : The M8 screws do NOT require a

washer. Use the universal washer (BO) ONLY with the

M4, M5 or M6 screws.

• Proper screw length requires base of screw head to

protrude above flat washer a distance equal to or

greater than the screw diameter. If screw length is

inadequate, select longer screw. Select shortest screw

which will protrude the required distance.

9. Place hinged frame onto back of flat panel and match the

VESA pattern on flat panel to the hinged frame mounting

slots. Also match the threaded studs in outer frame to the

hooks on the hinged frame. (See Figure 9)

10. Use selected screws (BA-BL), washers (BO--if required),

and spacers (BM, BN--if required), to connect hinged frame

to back of flat panel. (See Figure 9)

Figure 9

(B)

Swing door

Leave approximately

1/16" space between

edge of opening

(B)

Gasket

strip

and gasket strip

Depth-adjustable

outer frame

Flat panel

NOTE: Use universal washer (BO)

(BO)

(BM and/or BN)

(BA-BL) x 4

Outer

frame

ONLY with M4, M5 or

M6 screws.

LW40/42/43UxP LW40/42/43UxPG Installation Instructions

NOTE: The outer frame depth may be adjusted between

3" - 5" to make room for a variety of different flat panel

thicknesses. (See Figure 10)

• This outer frame adjustable depth can also be used to

make more space between the back of the flat panel

and wall for AV component storage.

• The 4 Phillips screws removed in Step 1 can be

replaced with four 10-24 x 2-3/4" Phillips screws (CD)

for larger depth adjustments.

Figure 10

11. Tighten thumb nuts over threaded studs in four locations on

the hinged frame. (See Figure 10)

12. Replace and fasten four Phillips screws which were

removed in Step 1, OR replace the removed screws with

four 10-24 x 2-3/4" Phillips head screws (CD) to allow for a

larger depth adjustment of the outer frame. (See Figure 10)

13. Carefully lift (using two people) the swing door with attached

flat panel.

IMPORTANT ! : Be sure to keep swing door at a 90°

angle to the wall to enable a smooth installation.

14. Keeping the swing door at a 90° angle against the wall, slide

the swing door so that hinge pins are above hinges.

15. Lower swing door to engage hinge pins into hinges. (See

Figure 11)

NOTE: Some resistance is normal when the hinge pins drop

into the hinges.

Figure 11

16. Close swing door and add 10-24 x 3/8" button head security

screw (CA) in hole below latch to lock door. (See Figure 11)

Thumb nuts x 4

Previously

(CD) x 4

removed OR

[Flat panel not shown]

Two washers

should remain

between hook

and outside

panel

Hinge pin

Hinge

(CA x 1)

Swing

door

Swing door must be closed before

Door

open

security screw (CA) is added

Be sure to keep swing door at a 90° angle to

the wall to enable a smooth installation.

Installation Instructions LW40/42/43UxP LW40/42/43UxPG

Cabling

1. Cables may be placed through the center slot in the wall

bracket flanges. (See Figure 12)

IMPORTANT ! : Cables should not be placed OVER the

wall bracket flanges. Damage to cables may occur. (See

Figure 12)

Figure 12

APPENDIX

Switching Hinge Location

1. Remove AND SAVE the hardware on the latch (right) side

of the wall bracket. (See Figure 13)

Figure 13

2. Remove and SAVE two lift-off hinges from hinged side of

wall bracket. (See Figure 14)

3. DISCARD the four fasteners from these hinge parts.

Figure 14

Center

slot

Do NOT place

cables (dashed

Wall

flanges

Place cables through

center slot in wall

bracket flanges.

lines shown

above) in areas

over wall bracket

flanges as shown.

Remove and SAVE

fasteners noted

all parts and

Wall

bracket

Remove and

SAVE two hinges

Wall

bracket

Hinge

LW40/42/43UxP LW40/42/43UxPG Installation Instructions

4. Remove and SAVE lift-off hinge and hinge spacer plate

from two locations on swing door. (See Figure 15)

5. DISCARD the four fasteners from these hinge parts.

Figure 15

6. Replace two lift-off hinges and hinge spacer plates onto

opposite side (left) of swing door. (See Figure 16)

7. Fasten in place with four (two each hinge)

NEW

10-32 x 3/4"

button head cap screws (CB). (See Figure 16)

Figure 16

8. Move the lift-off hinges to the right side of the wall bracket.

(See Figure 17)

9. Fasten in place with four (two each hinge)

NEW

10-32 x 5/16"

button head cap screws (CC). (See Figure 17)

Figure 17

Remove and

SAVE two hinges

and hinge

spacer plates

Spacer

plate

Hinge

Swing door

assembly

Lift-off

hinge

Hinge

spacer

plate

(CB) x 4

Wall

(CC) x 4

Lift-off

hinge

bracket

Installation Instructions LW40/42/43UxP LW40/42/43UxPG

10. Flip and install latch section on left side of wall bracket.

NOTE: Be sure that upper and lower tabs are slid into slots on

wall bracket. (See Figure 18)

11. Fasten in place with two washers and screws removed in

Step 1. (See Figure 18)

12. Re-install small horizontal tab removed from bottom of latch

section in Step 1, by fastening it onto the top of the latch

section. (See Figure 18)

13. Re-install outside latch using fastener removed in Step 1.

(See Figure 18)

14. Re-install inside latch: (See Figure 18)

a. Place spring on top of horizontal tab and compress

spring slightly.

b. Place latch over spring, lining up tabs on latch with slots

in wall bracket.

c. Fasten latch in place with button head cap screw and

washer removed earlier in Step 1.

Figure 18

x 2

Insert tab

at top and

into slot

bottom

Horizontal tab

Wall bracket

14a

14b

14c

x 1

Slots

Spring

Ta b s

LW40/42/43UxP LW40/42/43UxPG Installation Instructions

Fastener Installation Methods

IMPORTANT ! : See Table 1 for appropriate hardware

and pilot hole sizes for various wall types.

Wood Stud

1. Use one 5/16" x 2-1/2" hex flange head lag bolt (AA) and

one 5/16" washer (AB) through product and into pilot hole.

(See Figure 19)

2. Repeat for remaining pilot holes.

Figure 19

Concrete

1. Install one UX10x60R anchor (AF) into each pilot hole using

a hammer, making sure that the anchor is flush with the wall.

(See Figure 20)

2. Use one 5/16" x 2-1/2" hex flange head lag bolt (AA) and

one 5/16" washer (AB) through product into each anchor in

wall. (See Figure 20)

3. Repeat for remaining pilot holes.

Figure 20

Steel Stud

IMPORTANT ! : See Site Requirements for Steel Stud

Installation section before proceeding with Steel Studs

installation to ensure installation site meets requirements!

The drywall must have a minimum thickness of 1/2"!

1. Hold metal channel on anchor (AC) flat alongside plastic

straps and slide channel through hole. (See Figure 21)

Figure 21

2. Holding plastic straps on anchor (AC), pull anchor away from

wall until channel rests flush behind wall making sure anchor

channel is positioned vertically on drywall, or steel stud (if

present). (See Figure 22)

3. Slide plastic cap on anchor (AC) towards wall until flange of

cap is flush with wall. (See Figure 22)

Figure 22

4. Snap off plastic straps on anchor at wall by pushing side to

side, snapping off straps level with flange of plastic cap.

(See Figure 23)

Figure 23

(AA) x 8

(AB) x 8

(AA)

(AF)

(AB)

(AC)

Drywall

Plastic straps

(AC)

Plastic cap

Drywall

Anchor metal channel

Steel stud

(side view)

(if present)

Plastic straps

Drywall

Anchor metal channel

Plastic cap

Steel stud

(side view)

(if present)

Installation Instructions LW40/42/43UxP LW40/42/43UxPG

5. Line up anchor with attachment point.

6. Insert 1/4-20 x 1-3/4" Phillips pan head screw (AD) through

1/4" washer (AE), corresponding mounting hole in wall

bracket and into anchor (AC), and tighten until flush against

wall bracket. DO NOT over tighten! (See Figure 24)

Figure 24

Drywall

Anchor metal channel

(AD) x 4

Steel stud

(AE) x 4

(side view)

Wall bracket

(if present)

Site Requirements for Wood or Steel Stud Installation

Figure 25

There must be a minimum of

1-7/8" (48mm) clearance

inside wall

If back side of wall is unfinished,

to a minimum of one stud left

*Steel stud type and structural strength must conform to the North American Specification for the

Design of Cold-Formed Steel Structural Members. [362 S 125 18, C-Shaped, S-Stud Section]

drywall must be installed

and right of the stud(s) being used

to install the mount. Drywall must be

secured to studs with screws a

maximum of 12" (305mm) apart

down center of stud.

Wood stud (2 x 4) or Steel stud* (2 x 4 / 25ga minimum)

Plywood

3/4" minimum thickness

5/8" maximum drywall thickness

(Both Sides of Stud)

Drywall

1/2" minimum

Drywall Thickness

(Both Sides of Stud) plywood-covered with drywall

having maximum thickness of 5/8"

Plywood-covered

Studs

Drywall-covered

Studs

Steel Studs ONLY

24" on-center FRONT

[Steel Stud]

LW40/42/43UxP LW40/42/43UxPG Installation Instructions

USA/International A 6436 City West Parkway, Eden Prairie, MN 55344

P800.582.6480 / 952.225.6000

F877.894.6918 / 952.894.6918

Europe A Franklinstraat 14, 6003 DK Weert, Netherlands

P+31 (0) 495 580 852

F+31 (0) 495 580 845

Asia Pacific A Office No. 918 on 9/F, Shatin Galleria

18-24 Shan Mei Street

Fotan, Shatin, Hong Kong

P852 2145 4099

F852 2145 4477

8800-003145 Rev02

2019 Legrand | AV

www.legrandav.com

11/19