Table of Contents
D-Link DCS-4701E User Manual
Displayed below is the user manual for DCS-4701E by D-Link which is a product in the Security Cameras category. This manual has pages.
User Manual
Version 2.00 | 23/5/2018
DCS-4701E
Vigilance Full HD H.265 Outdoor Bullet Camera
2D-Link DCS-4701E User Manual
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or
organization of such revisions or changes. Information in this document may become obsolete as our services and websites develop and
change.
Manual Revisions
Revision Date Description
2.00 14/05/2018 Version B1 with rmware version 2.00
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other
countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.
Copyright © 2018 D-Link Corporation.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Corporation.
Preface
3D-Link DCS-4701E User Manual
Table of Contents
Product Overview ........................................................4
Package Contents .................................................................4
Introduction ............................................................................ 5
System Requirements .........................................................5
Features ....................................................................................6
Hardware Overview ............................................................. 7
Installation ...................................................................9
Mounting the Camera .........................................................9
Waterproong Your Installation ....................................11
Software Installation .........................................................14
Conguration ............................................................17
Using the Conguration Interface ................................17
Live Video ..............................................................................19
Setup Wizard ........................................................................21
Network Setup Wizard ..................................... 22
Motion Detection Setup Wizard ................................24
Settings ..................................................................................26
Network Settings ............................................................26
Camera Settings ..............................................................32
Event Management ........................................................39
Advanced Setup ..................................................................48
Advanced ........................................................................... 48
Camera Conguration ................................................... 54
Camera Options ..................................................................58
Camera Info .......................................................................58
Time .....................................................................................59
Administration Settings ...............................................62
Camera Log .......................................................................65
Technical Specications ............................................66
Regulatory Information ............................................68
4D-Link DCS-4701E User Manual
Section 1: Product Overview
Product Overview
Package Contents
If any of the above items are missing, please contact your reseller.
Safety Notice: Installation and servicing should be done by certied technicians to conform with all local codes and prevent voiding
your warranty.
DCS-4701E Vigilance Full HD H.265 Outdoor Bullet Camera
Mounting Kit
CD-ROM with User Manual and software
Quick Installation Guide
Cable Waterproong Connector
Rubber Power Connector Plug
5D-Link DCS-4701E User Manual
Section 1: Product Overview
Introduction
The DCS-4701E Vigilance Full HD H.265 Outdoor Bullet Camera is a professional surveillance and security solution for small, medium, and large
enterprises. It uses a full-HD progressive scan CMOS sensor to deliver low-noise video and low-light capability ideal for surveillance applications.
The DCS-4701E oers a complete surveillance solution featuring a built-in IR cut lter and IR LEDs eective up to 30 meters with built-in smart IR
function, avoiding overexposure of near objects at night, allowing it to stream simultaneous real-time full-HD resolution video 24/7. In addition,
the IP66-certied weatherproof housing make the DCS-4701E ideal for both indoor and outdoor applications.
The DCS-4701E streams video with H.265 compression which has lower a bandwidth requirement compared to H.264 while also saving storage
capacity of NVR/VMS. The DCS-4701E also incorporates Power over Ethernet (PoE), allowing it to be easily installed in a variety of locations especially
with D-Link Surveillance Switches which supports ONVIF and surveillance VLAN, bandwidth control, and cable diagnostics functions.
The DCS-4701E can be accessed remotely, controlled, and congured from any computer over your local network or through the Internet via a
web browser. The simple installation and intuitive web-based interface oer easy conguration across the full range of its advanced feature set and
make it an ideal choice for a dependable and cost-eective surveillance solution with easy clutter-free installation.
• Computer with Microsoft Windows® 10, 8, or 7, Mac OSX 10.9 or above
• Internet Explorer 9 or higher for Windows®, Firefox 2-51, 52 ESR, Chrome 42 or higher, or Safari 9 or higher for MacOS X
• Existing 10/100 Ethernet-based network with an available 802.3af Power over Ethernet (PoE) port
System Requirements
6D-Link DCS-4701E User Manual
Section 1: Product Overview
H.265 Compression
The DCS-4701E supports the latest H.265 compression algorithm to bring out the best combination of performance, quality, bandwidth, and storage
space.
Simple to Maintain
The DCS-4701E is a stand-alone system with a built-in CPU, requiring no special hardware or software. The DCS-4701E can be viewed and managed
through most web browsers, including Internet Explorer®, Chrome®, Firefox®, and Safari®.
Supports a Variety of Platforms
With support for TCP/IP networking, HTTP/HTTPS, and other Internet-related protocols, the DCS-4701E can also be integrated easily into other
Internet/Intranet applications because of its standards-based features. The DCS-4701E works in any network that supports 10/100 Ethernet, making
the DCS-4701E easy to integrate into your existing network environment.
Advanced Event Management
The DCS-4701E can be set up to send e-mail notications with snapshots when an event occurs, such as when motion is detected. Events can be
triggered from several sources, such as motion detection and time-based events.
IR LEDs for Day and Night Functionality
The built-in infrared LEDs enable night time viewing of up to 30 meters. With built-in smart IR function, it can avoid overexposure of near objects
at night.
IP66 Weatherproof and Vandal-proof Housing
The DCS-4701E uses an IP66 weatherproof housing, allowing you to rest assured that in the toughest of conditions, it will continue to provide
round-the-clock surveillance.
PoE (Power over Ethernet) for Flexible Installation
The DCS-4701E can draw all the power it needs from a PoE switch or PoE injector for a simple and clutter-free installation.
Remote Monitoring Utility
The D-Link D-ViewCam™ application adds enhanced features and functionality for the camera and allows administrators to congure and access
the camera from a separate site via Intranet or Internet. Other features include image monitoring, recording images to a hard drive, viewing up to
32 cameras on one screen, and taking snapshots.
Features
7D-Link DCS-4701E User Manual
Section 1: Product Overview
Hardware Overview
3
2
1
4
5
1 IR LEDs Provide illumination for low-light environments.
2 Camera Lens Camera lens to record video of the surrounding area.
3 Adjustment Ring Loosen to adjust and tighten to lock the camera angle.
4 Ethernet Port RJ-45 connector for Ethernet which can also be used to power the camera using Power over
Ethernet (PoE).
5 Power Port Connects to an optional 12 V / 1.5 A power adapter (not included).
8D-Link DCS-4701E User Manual
Section 1: Product Overview
1Grounding
Screw Used to connect the camera to ground.
2 Reset Button Press and hold this button down for 10 seconds to reset the camera to factory default settings.
12
Hardware Overview
9D-Link DCS-4701E User Manual
Section 2: Installation
Installation
Mounting the Camera
It is highly recommended that you congure and test your camera before mounting it. Refer to "Software Installation" on page 14 for more
information.
Step 1
Place the mounting sticker where you want to position the camera.
Use a 6 mm drill bit to make the required holes approximately 25 mm deep, then insert the
wall anchors into the holes.
Step 2
If you are running the camera cables through the wall, drill a hole in the center and pull
the cables through the hole.
Step 3
Use the screws provided to mount the camera to the wall.
If you are running the camera cables out the side of the camera, guide the camera cables
through the cable channel on the base.
10D-Link DCS-4701E User Manual
Section 2: Installation
Step 6
To adjust the camera's angle, turn the adjustment ring counterclockwise to loosen it, then move
the camera to the desired position and angle. When you are nished, turn the adjustment ring
clockwise to tighten it.
Step 5
Connect the power and Ethernet cables, or just the Ethernet cable if you are using a PoE
connection.
11D-Link DCS-4701E User Manual
Section 2: Installation
Waterproong Your Installation
Step 1
Place the washer around the base of the Ethernet connector as shown.
Round Ethernet cable, a crimping tool, and RJ-45 plugs are required for this procedure.
Step 2
Thread bare Ethernet cable through the waterproof connector as shown, then crimp an RJ-45
plug onto the cable.
Step 3
Crimp an RJ-45 connector onto the end of the cable.
Step 4
Connect the other end of the Ethernet cable to the camera's Ethernet port.
12D-Link DCS-4701E User Manual
Section 2: Installation
Step 6
Screw the back part of the waterproof connector clockwise until there is a tight seal around
the Ethernet cable.
Step 5
Connect the RJ-45 plug into the Ethernet connector, then screw the waterproof connector to
the Ethernet connector by turning it about a half-turn clockwise.
If you are using PoE to power your camera, use the power connector cap to seal the power
connector.
13D-Link DCS-4701E User Manual
Section 2: Installation
If you are using a power adapter (not included) to power your camera, wind waterproof
tape around the connection in an overlapping manner to cover it.
14D-Link DCS-4701E User Manual
Section 2: Installation
Step 1
Insert the DCS-4701E CD into your computer's CD-ROM drive to begin the installation.
If the Autorun function on your computer is disabled, or if the D-Link Launcher fails to start
automatically, click the Start button and type D:\autorun.exe (where D: represents the drive
letter of your CD-ROM drive) and press Enter.
Step 2
Click on the D-Link Setup Wizard SE icon that was created in your Windows Start menu (Start
> D-Link > Setup Wizard SE).
Software Installation
15D-Link DCS-4701E User Manual
Section 2: Installation
Step 4
Enter the Admin ID and password. When logging in for the rst time, the default Admin ID is
admin with the password left blank.
Click the checkboxes if you wish to change the admin ID and password for the camera, and
enter the new ID and password you wish to use.
Click Next to continue.
Step 3
The Setup Wizard will appear and display the MAC address and IP address of your camera(s). If
you have a DHCP server on your network, a valid IP Address will be displayed. If your network
does not use a DHCP server, the network camera's default static IP 192.168.0.20 will be
displayed.
Select your camera, then click the Wizard button to continue.
16D-Link DCS-4701E User Manual
Section 2: Installation
Step 6
Take a moment to conrm your settings and click Restart.
Step 5
Select DHCP if your camera obtains an IP address automatically from a DHCP server such as a
router. Select Static IP if you want to manually enter the IP settings for the camera.
Click Next to continue.
17D-Link DCS-4701E User Manual
Section 3: Conguration
Conguration
Using the Conguration Interface
After completing the Camera Installation Wizard, you are ready to use your camera. The camera’s built-in Web conguration utility is designed to allow
you to easily access and congure your DCS-4701E. At the end of the wizard, click Link, or enter the IP address of your camera into a web browser,
such as Firefox. To log in, use the User name admin and the password you created in the Installation Wizard. If you did not create a password, the
default password is blank. After entering your password, click OK.
Step 1
Click on the D-Link Setup Wizard SE icon that was created in your Windows Start menu (Start
> D-Link > Setup Wizard SE).
Step 2
Select the camera and click Link to access the web conguration.
The Setup Wizard will automatically open your web browser to the IP address of the camera.
18D-Link DCS-4701E User Manual
Section 3: Conguration
Step 3
The first time you connect to the camera, you will be asked to set a password for the
administrator account. After entering a password, click Save.
OR
Under Password, enter the same password congured during setup and click Login to continue.
Step 4
This section displays your camera’s live video. You can select your video prole and view or
operate the camera.
19D-Link DCS-4701E User Manual
Section 3: Conguration
Live Video
This section shows your camera’s live video. You may select any of the available icons listed below to operate the camera. You may also select your
language using the drop-down menu on the left side of the screen.
If your view window area is less than your frame size, you can click and drag on the live video to move the camera view around. Refer to "Video
Stream" on page 37.
Setup Clicking this will take you to the camera conguration pages.
Edit Toolbar
Clicking this will allow you to add and remove icons from the
toolbar. This lets you create a custom toolbar with only the
options you want.
Window Size
You can choose between various screen sizes for your camera's
video:
Auto Screen: Automatically resize the camera video to
match your browser window
Full Screen: View your camera video using the entire screen
100% Screen: View your camera's video at 100% size
50% Screen: View your camera's video at 50% size
25% Screen: View your camera's video at 25% size
Video Prole 1/2 Select a video prole to use. For more on setting up your video
proles, refer to "Video Stream" on page 37.
Take a Snapshot This will save a snapshot to your PC using the storage folder you
have selected.
Record a Video
Clip
This will start recording a video clip to your PC using the storage
folder you have selected. Click it again to stop recording. If you
close the browser window, the recording will stop.
Set a Storage
Folder
Select a storage folder to save snapshots and video clips to.
Zoom In/Out Click this and use the slider to zoom in and out of your camera's
video.
20D-Link DCS-4701E User Manual
Section 3: Conguration
You can nd these icons in the top-right corner of the Live Video screen:
Alarm This will ash red when motion is detected or a DI signal is
received.
Record Status This will turn red when the camera is recording.
Help Click this to open a window that describes the Live Video
controls.
Logout Click this to log out of the web interface.
21D-Link DCS-4701E User Manual
Section 3: Conguration
Setup Wizard
This page lets your use setup wizards to walk you through setting up your camera's network and motion detection settings.
Network Setup
Wizard:
Motion
Detection
Setup Wizard:
Click on this button to start the Network Setup Wizard. Refer to "Network
Setup Wizard" on page 22.
Click on this button to start the Motion Detection Setup Wizard. Refer to
"Motion Detection Setup Wizard" on page 24.
22D-Link DCS-4701E User Manual
Section 3: Conguration
Network Setup Wizard
This wizard will guide you through a step-by-step process to congure your camera and
connect it to the Internet. Click Next to continue.
Step 1:
Select how the camera will connect to the Internet.
• If your camera is connected to a router, or you are unsure how your camera will connect to
the Internet, select DHCP.
• Select Static IP Client if your Internet Service Provider has provided you with connection
settings, or if you wish to set a static address within your home network. Enter the correct
conguration information and click Next to continue.
• If you are using PPPoE, select PPPoE and enter your user name and password.
Click Next to continue.
23D-Link DCS-4701E User Manual
Section 3: Conguration
Step 2:
If you have a Dynamic DNS account and would like the camera to update your IP address
automatically, select Enable DDNS and enter your host information. Click Next to continue.
Step 3:
Enter a name for your camera and click Next to continue.
Step 4:
Set the correct time to ensure that all events will be triggered as scheduled. Click Next to
continue.
Step 5:
Conrm the settings are correct and click Apply to save them. The settings will be saved to
the DCS-4701E and the camera will restart.
24D-Link DCS-4701E User Manual
Section 3: Conguration
Motion Detection Setup Wizard
This wizard will guide you through a step-by-step process to congure your camera's
motion detection functions.
Click Next to continue.
Step 1
This step will allow you to enable or disable motion detection, specify the detection sensitivity,
and dene what parts of the camera's view to monitor for motion.
You may specify whether the camera should capture a snapshot or record a video clip when
motion is detected.
Please refer to "Motion Detection" on page 47 for more information about how to congure
motion detection.
Click Next to continue.
Step 2
This step allows you to enable motion detection based on a customized schedule. Specify the
day and hours. You may also choose to always record whenever motion is detected.
Click Next to continue.
25D-Link DCS-4701E User Manual
Section 3: Conguration
Step 3
This step allows you to specify where to send the snapshot/video clip/system log when motion
is detected. Select E-mail, FTP, or Network Storage and enter the relevant information.
Click Next to continue.
Step 4
You have completed the Motion Detection Wizard.
Please verify your settings and click Apply to save them.
Please wait a few moments while the camera saves your settings and restarts.
26D-Link DCS-4701E User Manual
Section 3: Conguration
Settings
Network Settings
Use this section to congure the network connections for your camera. All relevant information must be entered accurately. Please note that PPPoE
must be disabled to make any changes on this page; refer to "PPPoE" on page 27 for more details. After making any changes, click the Save
button to save your changes.
DHCP:
Static IP Client:
IP address:
Subnet mask:
Default router:
Primary DNS:
Secondary
DNS:
Select this connection if you have a DHCP server running on your network
and would like your camera to obtain an IP address automatically.
If you choose DHCP, you do not need to ll out the IP address settings.
You may obtain a static or xed IP address and other network information
from your network administrator for your camera. A static IP address may
simplify access to your camera in the future.
Enter the xed IP address in this eld.
This number is used to determine if the destination is in the same subnet.
The default value is 255.255.255.0.
Enter the router/gateway used to forward frames to destinations in a
dierent subnet. Invalid router/gateway settings may cause the failure of
transmissions to a dierent subnet.
Enter the primary domain name server for translating domain names to IP
addresses.
Enter the secondary domain name server for translating domain names to
IP addresses.
LAN Settings
27D-Link DCS-4701E User Manual
Section 3: Conguration
Enable IPv6:
Manually
Setup The IP
Address:
Enable the IPv6 setting to use the IPv6 protocol.
Enabling the option allows you to manually set up the address, specify an
optional IP address, specify an optional router address, and an optional
primary DNS address. You can click the Information button to see the IPv6
address lists for the host, gateway, and DNS server.
IPv6
Use this section to congure your camera's IPv6 settings. After making any changes, click the Save button to save your changes.
PPPoE
Enable PPPoE:
User Name /
Password:
PPPoE Status:
Enable this setting if your network uses PPPoE.
Enter the username and password for your PPPoE account. Re-enter your
password in the Conrm Password eld. You may obtain this information
from your ISP.
This shows your current PPPoE connection status.
Use this section to congure your camera's PPPoE settings. After making any changes, click the Save button to save your changes.
28D-Link DCS-4701E User Manual
Section 3: Conguration
HTTP and HTTPS
HTTP Port:
Access Name
for Stream 1~2:
The default port number is 80.
The default name is video#.mjepg, where # is the number of the stream.
HTTP
Use this section to congure the HTTP and HTTPS access settings for your camera. After making any changes, click the Save button to save your
changes.
29D-Link DCS-4701E User Manual
Section 3: Conguration
HTTPS Port:
Enable
HTTPS Secure
Connection:
Create
Certicate
Method:
Status:
Note:
You may use a PC with a secure browser to connect to the HTTPS port of
the camera. The default port number is 443.
Enable the HTTPS service.
Choose the way the certicate should be created. Three options are
available:
Create a self-signed certicate automatically
Create a self-signed certicate manually
Create a certicate request and install
Displays the status of the certicate.
The certicate cannot be removed while the HTTPS is still enabled. To
remove the certicate, you must rst uncheck HTTPS secure connection.
HTTPS
30D-Link DCS-4701E User Manual
Section 3: Conguration
RTSP and Multicast
Authentication:
RTSP Port:
Access Name
for Stream 1/2:
Choose to enable or disable RTSP digest encryption. Digest encryption
uses MD5 hashes.
The port number that you use for RTSP streaming to mobile devices, such
as mobile phones or tablets. The default port number is 554.
You may specify the address of a particular stream. For instance, live1.sdp
can be accessed at rtsp://x.x.x.x/live1.sdp where the x.x.x.x represents the
ip address of your camera.
Use this section to congure your camera's RTSP and multicast stream settings. After making any changes, click the Save button to save your
changes.
RTSP
Multicast
Multicast for
Stream 1/2:
The DCS-4701E allows you to multicast each of the available streams via
a group address and specify the TTL value for each stream. Enter the port
and TTL settings you wish to use if you do not want to use the defaults.
31D-Link DCS-4701E User Manual
Section 3: Conguration
Bonjour
Use this section to enable Bonjour, which allows your camera to be accessed more easily on your network. After making any changes, click the
Save button to save your changes.
Bonjour:
Bonjour Name:
Enable this to enable Bonjour support.
Enter a name to identify this camera on Bonjour.
32D-Link DCS-4701E User Manual
Section 3: Conguration
IP Camera
Name:
LED:
Create a unique name for your camera that will be added to the le name
prex when creating a snapshot or a video clip.
You may specify whether or not to illuminate the status LED on the camera.
For security reasons, this setting is set to O by default.
Camera Settings
Camera Settings
Use this section to congure the device name and LED behavior for your camera. After making any changes, click the Save button to save your
changes.
33D-Link DCS-4701E User Manual
Section 3: Conguration
Image Settings
Mirror:
Flip:
Anti-Flicker:
White Balance:
Exposure
Mode:
Denoise:
This will mirror the image horizontally.
This will ip the image vertically. When turning Flip on, you may want to
consider turning Mirror on as well.
Select the frequency used by your power lines to avoid interference or
distortion.
Use the drop-down box to change white balance settings to help balance
colors for dierent environments. You can choose from Auto, Outdoor,
Indoor.
Changes the exposure mode. Use the drop-down box to set the camera for
Indoor, Outdoor, or Night environments, or to Moving to capture moving
objects. You can also create 3 dierent custom exposure modes. Max Gain
will limit the brightness of the exposure.
This setting controls the amount of noise reduction that will be applied to
the picture.
Image
In this section, you may congure the video image settings for your camera. All changes in the Image Settings section will be made immediately.
For the other sections, after making any changes, click the Save button to save your changes.
34D-Link DCS-4701E User Manual
Section 3: Conguration
Adjust this setting to compensate for backlit subjects.
Adjust this setting to alter the color intensity/strength.
This setting controls the amount of coloration, from grayscale to fully
saturated.
Specify a value to determine how much sharpening to apply to the image.
Wide Dynamic Range (WDR) helps improve exposure, making it easier to
see objects in very bright or dark areas of the camera's image. Specify a
value to determine how much WDR adjustment to apply to the image, or
select None.
This reduces the amount of image noise when viewing a low-light
environment.
Click this button to reset the image to factory default settings.
Brightness:
Contrast:
Saturation:
Sharpness:
WDR Level:
3D Filter:
Reset Default:
35D-Link DCS-4701E User Manual
Section 3: Conguration
Automatic:
Day Mode:
Night Mode:
Schedule
Mode:
IR Light
Control:
O:
On:
Sync With ICR:
Schedule:
The Day/Night mode is set automatically. Generally, the camera uses Day
mode and switches to Night mode when needed. Use the Sensitivity drop-
down box to select when the camera should switch to Night mode. The text
to the right of the drop-down box shows what the current lighting conditions
are like, and you can refresh this information by clicking the Refresh button.
Day mode enables the IR Cut Filter and turns o the IR LEDs.
Night mode disables the IR Cut Filter and turns on the IR LEDs.
Set Day/Night mode using the schedule set in the drop-down boxes. The
camera will enter Day mode at the starting time and return to Night mode
at the ending time.
Activate the Disable IR LED to set Day mode for the set times.
The camera can enable or disable the IR (infrared) light according to your
preferences. This setting provides additional controls depending on your
specic application.
Disables the IR light.
Enables the IR light.
The IR light will turn on when the ICR lter is disabled (night mode).
The IR light will turn on or o according to the schedule that you specify
below.
ICR & IR
Use this section to congure the IR LED and IR-cut removable lter behavior
for your camera.
ICR
IR Light
36D-Link DCS-4701E User Manual
Section 3: Conguration
OSD Settings
OSD:
Label:
Select this option to enable the On-Screen Display feature for your camera.
This will allow some information to appear in the top-left corner of the
camera's video.
Enter a label for the camera, which will be shown on the OSD when it is
enabled.
Privacy Mask
Enable Privacy
Mask Setting:
Restore All:
The Privacy Mask setting allows you to click and drag the mouse cursor
over the camera image to draw maximum 3 rectangular areas which will be
blocked/excluded from recordings and snapshots. Click the Save button to
save your changes.
Clear all privacy mask areas.
37D-Link DCS-4701E User Manual
Section 3: Conguration
Video Stream
Aspect Ratio:
Mode:
Frame Size:
Maximum
Frame Rate:
Set whether you want your camera to use a 4:3 or 16:19 aspect ratio for its
video. When changing this setting, you will need to redo setup for motion
detection, privacy masks, and preset points.
Set the video codec to be used to H.264, H.265, or JPEG.
Select what frame size to use. Frame size determines the total capture
resolution. Larger frame sizes provide more detail, but will require more
bandwidth.
You can set the maximum frame rate. A higher frame rate provides smoother
motion for videos and requires more bandwidth. Lower frame rates will
result in stuttering motion and require less bandwidth.
You may congure up to 2 video proles with dierent settings for your camera. This allows you to set dierent settings for recording video and for
viewing your video remotely, for example. After making any changes, click the Save button to save your changes.
38D-Link DCS-4701E User Manual
Section 3: Conguration
Constant Bit
Rate:
Fixed Quality:
You can set the bit rate to use for this video prole.
Select the image quality level for the camera to try to maintain. Higher
quality levels will result in increased bit rates and use more bandwidth.
39D-Link DCS-4701E User Manual
Section 3: Conguration
Event Management
Event Management
The DCS-4701E has a comprehensive event management system that lets you congure the camera to perform certain actions when an event
occurs. For example, when motion is detected, you can have snapshots sent to an e-mail address. You can also congure the camera to take regular
video recordings according to a schedule you dene. Detailed information for the following steps can be found in the following pages.
Action
Step 1: Select your destination Server and Media type Step 2: Select your Trigger event and Action
Server
• E-mail
• FTP
• Network Storage
Media
• Snapshot
• Video Clip
• System Log
• Video motion detection
• Periodic
• System boot
• Event schedule
Event
• Server (can be any pre-selected
media such as snapshot, video
clip, or system log)
Event
Server 1:
E-mail
Server 2:
FTP
Action
Media 1:
Snapshot
Media 2:
Video Clip
When an event is triggered:
40D-Link DCS-4701E User Manual
Section 3: Conguration
The Event Setup page includes 4 dierent sections:
• Server
• Media
• Event Settings
• Recording
1. To add a new server, media, event, or recording item, click Add. A screen will appear and
allow you to update the elds accordingly.
2. To delete the selected item from the server, media, event, or recording drop-down menus,
click the Delete button next to it.
3. Click on the name of an item to edit it.
Event Management
41D-Link DCS-4701E User Manual
Section 3: Conguration
Server Name:
Email:
FTP:
Network
Storage:
Enter the name for the server.
If you want to use an e-mail address for your server, select this and enter the
settings for your target e-mail account.
If you want to use an FTP server for your server, select this and enter the
settings for your target FTP server.
If you want to use a network storage device for your server, select this and
enter its settings here.
Server
You can congure a server for each server type, and up to 5 FTP servers. After making any changes, click the Save button to save
your changes.
42D-Link DCS-4701E User Manual
Section 3: Conguration
Media Name:
Snapshot:
Source:
Send pre-event
image(s):
Send post-
event image(s):
Enter a unique name for media type you want to create.
Select this option to set the media type to snapshots.
Set the video prole to use as the media source. Refer to "Video Stream" on
page 37 for more information on video proles.
Set the number of pre-event images to take. Pre-event images are images
taken before the main event snapshot is taken.
Set the number of post-event images to take. Post-event images are images
taken after the main event snapshot is taken.
For example:
If both the Send pre-event images and Send post-event images are set to 4,
a total of 9 images are generated after a trigger is activated.
1 pic. 2 pic. 3 pic. 4 pic. 5 pic. 6 pic. 7 pic. 8 pic. 9 pic.
The moment the
trigger is activated.
Media
There are three types of media: Snapshot, Video Clip, and System Log. You can make a media entry for each type. After making
any changes, click the Save button to save your changes.
43D-Link DCS-4701E User Manual
Section 3: Conguration
File name
prex:
Add date and
time sux to
le name:
Video clip:
Source:
Pre-event
recording:
Maximum
duration:
Maximum le
size:
File Name
Prex:
System log:
The prex name will be added to the le name.
SNAPSHOTS20080104_100341
Date and time suffix
The format is: YYYYMMDD_HHMMSS
File name prefix
Enable this to add the date and time the snapshot was recorded as a le
name sux.
Select this option to set the media type to video clips.
Set the video prole to use as the media source. Refer to "Video Stream" on
page 37 for more information on video proles.
This sets how many seconds to record before the main event video clip starts.
Set the maximum length of video to record for your video clips.
Set the maximum le size to record for your video clips.
This is the prex that will be added to the lename of saved video clips.
Select this option to set the media type to system logs. This will save the
event to the camera system log, but will not record any snapshots or video.
44D-Link DCS-4701E User Manual
Section 3: Conguration
Create and schedule up to three events with their own settings here. After making any changes, click the Save button to save
your changes.
Event name:
Enable this
event:
Priority:
Delay for:
Enter a name for the event.
Toggle this to activate this event.
Set the priority for this event. Events with higher priority will be executed
rst.
Specify the delay time before allowing this event to be triggered again. This
is used for both motion detection events and event triggers.
Event
Selecting this will trigger the event when motion is detected during live
video monitoring. Make sure you have enabled motion detection and
specied what part of the image to monitor for motion. For more details,
refer to "Motion Detection" on page 47.
Selecting this will trigger the event in specied intervals. The trigger interval
unit is in minutes.
Selecting this will trigger an event when the system boots up.
Video Motion
Detection:
Periodic:
System Boot:
Trigger
45D-Link DCS-4701E User Manual
Section 3: Conguration
Action: Select the actions you want the camera to take when the event happens.
Select the Server to use, then choose the Media you want to save to it. Please
note that you need to set up your Server and Media entries rst.
Event Schedule
Specify when you want to monitor for this event. Select which days to
monitor for this event, then select Always or enter the time interval to
monitor for the specied event.
46D-Link DCS-4701E User Manual
Section 3: Conguration
Here you can congure and schedule the recording settings. After making any changes, click the Save button to save your changes.
Recording
Entry Name:
Enable This
Recording:
Priority:
Source:
Enter a name for the recording.
Select this to enable the recording function.
Set the priority for this entry. An entry with a higher priority value will be
executed rst.
Select the video prole to use as the recording source.
Recording
Use the checkboxes to set which days to record video on. Select Always to
record for the entire day, or select From and select what period of time you
want to record using the drop-down boxes.
Select a storage destination that was congured in Server to send recordings
there.
If this is selected, les will be split based on the le size you specify.
If this is selected, les will be based on the maximum length you specify.
The prex name will be added to the beginning of the le name of the
recording le(s).
Destination:
Size of Each
File for
Recording:
Time of
Each File for
Recording:
File Name
Prex:
Recording Schedule
47D-Link DCS-4701E User Manual
Section 3: Conguration
Enable Video
Motion:
Sensitivity:
Percentage:
Enable this to enable the motion detection feature of your camera. Please
note that you must create at least one motion detection box for the camera
to detect motion.
Set how sensitive motion detection will be from 0% to 100%. A low sensitivity
means that there must be large changes between two images in order to
detect motion, and a high sensitivity means that even small changes will
cause motion to be detected.
Low sensitivities may be useful when monitoring an area that has ickering
lights or a window to the outside in view. High sensitivities may be useful
when monitoring an area that rarely changes, such as a storeroom or
warehouse.
Set how much of the area being monitored for motion must change for
motion to be detected. A low percentage means that only part of the area
being monitored has to change to detect motion, and a high percentage
means that most of the area needs to change to detect motion.
Low percentages can be useful when monitoring an area such as a large
room, and high percentages can be useful when you are only monitoring a
specic part of the camera's view, such as a doorway.
Motion detection enables the camera to monitor the video feed for movement. Here, you can adjust the sensitivity settings that determine whether
motion is detected by the camera or not. After making any changes, click the Save button to save your changes.
Motion Detection
48D-Link DCS-4701E User Manual
Section 3: Conguration
Advanced Setup
Advanced
UPnP
Enable UPnP
Presentation:
Enable
UPnP Port
Forwarding:
Forwarding
Port:
Forwarding
Status:
Enabling this setting allows your camera to be congured as a UPnP device
on your network.
Enabling this setting allows the camera to add port forwarding entries into
the router automatically on a UPnP capable network.
If UPnP Port Forwarding is enabled, you can set which port to use for
forwarding.
If UPnP Port Forwarding is enabled, this will show the UPnP Port Forwarding
status.
Enabling Video Motion will allow your camera to use UPnP to automatically set up port forwarding on your router. After making any changes, click
the Save button to save your changes.
49D-Link DCS-4701E User Manual
Section 3: Conguration
DDNS allows you to compensate for changing IP addresses by having a URL that automatically points to the current IP address of your camera. To
do this, you will need to have an account with one of the DDNS services listed in the drop-down box on this page. After making any changes, click
the Save button to save your changes.
DDNS
DDNS:
Server Address:
Host Name:
User Name:
Password:
Verify
Password:
Timeout:
Status:
Check this box to enable the DDNS function.
Enter your DDNS server address, or select a service from the drop-down
menu.
Enter the host name of the DDNS service.
Enter the username or e-mail address used to connect to the DDNS service.
Enter the password used to connect to the DDNS service.
Enter your DDNS service password again.
You can set up how often the camera noties the DDNS service of its current
global IP address by entering a whole number in hours.
This shows the current status of your DDNS updates.
50D-Link DCS-4701E User Manual
Section 3: Conguration
Here you can set the Simple Network Management Protocol (SNMP) settings for the camera, which allow for SNMP management of the camera.
After making any changes, click the Save button to save your changes.
SNMP
Enable
SMNPv1,
SNMPv2c:
Read/Write
Community:
Read Only
Community:
Enable
SNMPv3:
Read/Write
Security Name:
Authentication
Type:
Authentication
Password:
Encryption
Password:
Read Only
Security Name:
Enable this option to allow for SNMPv1 and SNMPv2c management of the
camera.
Enter a name for the read/write community of your SNMP server.
Enter a name for the read-only community of your SNMP server.
Enable this option to allow SNMPv3 management of the camera.
Enter a name for the read/write community of your read/write SNMP server.
Enter the type of authentication used by your read/write SNMP server.
Enter the authentication password used for your read/write SNMP server.
Enter the encryption password used for your read/write SNMP server.
Enter a name for the read-only community of your read-only SNMP server.
51D-Link DCS-4701E User Manual
Section 3: Conguration
Enter the type of authentication used by your read-only SNMP server.
Enter the authentication password used for your read-only SNMP server.
Enter the encryption password used for your read-only SNMP server.
Authentication
Type:
Authentication
Password:
Encryption
Password:
52D-Link DCS-4701E User Manual
Section 3: Conguration
Class of Service (CoS) and Quality of Service (QoS) allow you to prioritize surveillance trac on your network to ensure that your cameras can
stream video smoothly and remain accessible even when there is heavy trac on your network. Your network must support CoS or QoS in order
to use them. After making any changes, click the Save button to save your changes.
CoS and QoS
Enable CoS:
Enable QoS:
Enabling the Class of Service setting implements a best-eort policy to
prioritize trac without making any bandwidth reservations.
To use CoS, enable it, enter the VLAN ID to use for the camera, and set the
priority for your Live Video, Live Audio, Event/Alarm, and Management
camera trac.
Enabling QoS allows you to specify a trac priority policy to ensure a
consistent Quality of Service during busy periods. If the network camera is
connected to a router that itself implements QoS, the router's settings will
override the QoS settings of the camera.
To use QoS, enable it and set the priority for your Live Video, Live Audio,
Event/Alarm, and Management camera trac.
53D-Link DCS-4701E User Manual
Section 3: Conguration
Here you can dene which IP addresses are allowed to view your DCS-4701E. You can set up to 7 IP address ranges for both the allow and deny lists.
Access List
Allow List:
Start IP
Address:
End IP Address:
Delete Allow
List:
Deny List:
Start IP
Address:
End IP Address:
Delete Deny
List:
The section lets you dene what IP addresses have access rights to the
camera.
Note: When adding entries to the Allow list, make sure the rst entry includes
the IP address of the computer or device you are using to access the camera.
Otherwise, you may be blocked from accessing the camera after adding the
entry to the Allow list.
The starting IP address of the IP address range for the devices (such as a
computer) that have permission to access the video of the camera.
The ending IP address of the IP address range for the devices (such as a
computer) that have permission to access the video of the camera. Click Add
to save your changes.
Select an entry to remove from the Allow List, then click Delete.
The list of IP addresses that have no access rights to the camera.
The starting IP address of the IP address range for the devices (such as a
computer) that will be denied access to the camera.
The ending IP address of the IP address range for the devices (such as a
computer) that will be denied access to the camera. Click Add to save your
changes.
Select an entry to remove from the Deny List, then click Delete.
Note: All addresses in the Deny List will be denied access, even if they are
also in the Allow List.
54D-Link DCS-4701E User Manual
Section 3: Conguration
Camera Conguration
Save and Load Conguration
In this section, you may back up or restore the camera conguration.
Save To Local
Hard Drive:
Load From
Local Hard
Drive:
You may save your current camera conguration as a le on your computer.
Locate a pre-saved conguration by clicking Browse and then restore the
pre-dened settings to your camera by clicking Load Conguration.
55D-Link DCS-4701E User Manual
Section 3: Conguration
Here you can reset the camera conguration back to the factory defaults.
Factory Reset
Restore
to Factory
Default:
You may reset your camera and restore the factory settings by clicking
Restore Factory Defaults.
56D-Link DCS-4701E User Manual
Section 3: Conguration
Here you can reboot the camera, or set a schedule to reboot the camera automatically.
Reboot Device
Reboot Device:
Schedule
Reboot:
This will restart your camera.
If you want your camera to reboot on a regular schedule, enable this
option, then select the days and time you want the camera to reboot on
and click the Save button.
57D-Link DCS-4701E User Manual
Section 3: Conguration
Here you can update the camera's rmware. The current version of the rmware is shown next to the D-Link logo at the top of the page.
Firmware Update
File Path: To update the rmware, select a rmware le to use from your hard drive
by clicking Browse..., then click the Upload button.
Note: While the rmware is being updated, do not close the web browser
or disconnect your camera's power or network connection until the update
is complete.
58D-Link DCS-4701E User Manual
Section 3: Conguration
This page displays detailed information about your camera, the services running on your camera, and active video streams.
Camera Options
Camera Info
59D-Link DCS-4701E User Manual
Section 3: Conguration
This section allows you set the time zone and Daylight Saving settings for your camera.
Time
Time Settings
Time Zone:
Daylight
Saving:
Oset:
Start Time:
End Time:
Select your time zone from the drop-down menu.
If your region uses Daylight Saving time, you can enable it here. Select
Set date and time manually if you want to manually set the oset and the
period of time that the Daylight Saving correction should be used.
Enter the oset that should be used when Daylight Saving is being used.
Set the date and time that Daylight Saving should start.
Set the date and time that Daylight Saving should end.
60D-Link DCS-4701E User Manual
Section 3: Conguration
This section lets you set your camera's date and time automatically by using an NTP server.
Auto Time Cong
NTP Server: Enable this option to set your camera's time using an NTP server, then
select an NTP server to use from the drop-down box.
61D-Link DCS-4701E User Manual
Section 3: Conguration
This section lets you manually set your camera's date and time. If you have NTP Server enabled in Auto Time Cong, you will need to disable it
before setting the date and time manually.
Set Date and Time
Set Date and
Time Manually:
Copy Your PC's
Time:
Enable this option to manually set the time and date.
This will synchronize the time information with your PC.
62D-Link DCS-4701E User Manual
Section 3: Conguration
Here, you may modify the administrator’s password for your camera.
Administration Settings
Admin Password
New Password
/ Retype
Password:
Set a new password for the administrator’s account.
63D-Link DCS-4701E User Manual
Section 3: Conguration
Here, you may add user accounts for accessing the camera. User accounts are allowed to access the Live Video page, but cannot access any of the
camera's conguration pages.
User Accounts
User Name:
New Password
/ Retype
Password:
Enter a user name for the user you wish to create.
Enter a password for the user you wish to create.
64D-Link DCS-4701E User Manual
Section 3: Conguration
Here, you may manage the user accounts for accessing the camera.
User List
User Name: If you want to change a user's password, select a user from the drop-down
box, enter the new password, then click the Modify button.
If you want to remove a user from the user list, select a user from the drop-
down box, then click the Delete button.
65D-Link DCS-4701E User Manual
Section 3: Conguration
This page displays the log information of your camera. You may download the information by clicking Download. You may also click Clear to delete
the saved log information.
Camera Log
66D-Link DCS-4701E User Manual
Appendix A: Technical Specications
Technical Specications
Technical Specications
Camera
Camera Hardware Profile • 1/2.7” 2-megapixel progressive CMOS sensor
• 30 meter IR illumination distance
• Minimum illumination:
• 0.1 lux (color)
• 0.05 lux (B/W)
• 0 lux (IR LED on)
• Built-in Infrared-Cut Removable (ICR) Filter module
• 10x digital zoom
• Minimum object distance 0.5 m
• Focal length: 3.6 mm
• Aperture: F1.8
• Angle of view:
• (H) 90°
• (V) 50°
• (D) 104°
Camera Housing • IP66 compliant weatherproof housing • Wire-in bracket
Image Features • Configurable image size, quality, frame rate, and bit rate
• Time stamp and text overlays
• Configurable motion detection windows
• Configurable privacy mask zones
• Configurable shutter speed, brightness, saturation, contrast, and sharpness
• WDR
• 3D filter
Video Compression • Simultaneous H.265/H.264/MJPEG format compression
• H.265/H.264/MJPEG multicast streaming
• JPEG for still images
Video Resolution • 16:9 - 1920 x 1080, 1280 x 720, 800 x 448, 640 x 480 up to 30 fps • 4:3 - 1440 x 1080, 900 x 720, 800 x 592, 640 x 480 up to 30 fps
External Device Interface • 10/100 BASE-TX Fast Ethernet port • Supports 802.3af PoE
Network
Network Protocols • IPv6
• IPv4
• TCP/IP
• UDP
• ICMP
• DHCP client
• NTP client (D-Link)
• DNS client
• DDNS client (D-Link)
• SMTP client
• FTP client
• HTTP / HTTPS
• Samba client
• PPPoE
• UPnP port forwarding
• RTP / RTSP/ RTCP
• IP filtering
• Multicast
• SNMP
• ONVIF compliant
Security • Administrator and user group protection
• Password authentication
• HTTP and RTSP authentication
67D-Link DCS-4701E User Manual
Appendix A: Technical Specications
System Management
Event Management • Motion detection
• Event notification and uploading of snapshots/video clips via e-mail or FTP
• Supports multiple SMTP and FTP servers
• Multiple event notifications
• Multiple recording methods for easy backup
Remote Management • Remote management via D-ViewCam™ software
• Configuration interface accessible via web browser
• Remotely take snapshots/video clips and save to local hard drive
System Requirements for Web Interface • Windows 10/8/7 or Mac OS X 10.9 and higher • Internet Explorer 9 and higher (on Windows), Firefox 12-51, 52 ESR, Chrome 42
and higher, or Safari 9 and higher (on Mac OS X).
D-ViewCam™ System Requirements • Operating System:
• 32-bit: Windows 8 / 7 (SP1)
• 64-bit: Windows 10 / 8 / 7 (SP1) / Server 2012 / Server 2008 R2
• Web Browser: Internet Explorer 7 or higher
• Protocol: Standard TCP/IP
D-ViewCam™ Software Functions • Remote management of up to 32 cameras
• Supports all management functions provided in web interface
• Viewing of up to 32 cameras on one screen
• Scheduled, motion triggered, or manual recording options
General
Weight • 445 g ± 5 %
External Power Adapter • Input: 100 to 240 V AC, 50/60 Hz • Output: 12 V DC 1.5 A
Power Consumption • 3.2 (DC) / 3.1 W (PoE) ± 5%
Temperature • Operating: -30 to 50 °C (-22 to 122 °F) • Storage: -20 to 70° C (-4° to 158° F)
Humidity • Operating: 20 % to 80 % non-condensing • Storage: 5 % to 95 % non-condensing
Certifications • CE
• CE LVD
• FCC
• C-Tick
Dimensions
Ø 65
164.7
66.698.1
68D-Link DCS-4701E User Manual
Appendix B: Regulatory Information
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
Non-modication Statement
Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Innovation, Science and Economic Development Canada (ISED) Statement:
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
警告使用者:
此為甲類的資訊技術設備，在居住環境中使用時，可能會造成射頻擾動，在這種情況下，使用者會被要求採取某些適當的對策。
Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required
to take adequate measures.
CE EMI Class A Warning
This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference.
69D-Link DCS-4701E User Manual
Appendix B: Regulatory Information
SAFETY INSTRUCTIONS
The following general safety guidelines are provided to help ensure your own personal safety and protect your product from potential damage.
Remember to consult the product user instructions for more details.
• Static electricity can be harmful to electronic components. Discharge static electricity from your body (i.e. touching grounded bare metal)
before touching the product.
• Do not attempt to service the product and never disassemble the product. For some products with a user replaceable battery, please read
and follow the instructions in the user manual.
• Do not spill food or liquid on your product and never push any objects into the openings of your product.
• Do not use this product near water, areas with high humidity, or condensation unless the product is specically rated for outdoor application.
• Keep the product away from radiators and other heat sources.
• Always unplug the product from mains power before cleaning and use a dry lint free cloth only.
SICHERHEITSVORSCHRIFTEN
Die folgenden allgemeinen Sicherheitsvorschriften dienen als Hilfe zur Gewährleistung Ihrer eigenen Sicherheit und zum Schutz Ihres Produkts.
Weitere Details nden Sie in den Benutzeranleitungen zum Produkt.
• Statische Elektrizität kann elektronischen Komponenten schaden. Um Schäden durch statische Auadung zu vermeiden, leiten Sie
elektrostatische Ladungen von Ihrem Körper ab,
(z. B. durch Berühren eines geerdeten blanken Metallteils), bevor Sie das Produkt berühren.
• Unterlassen Sie jeden Versuch, das Produkt zu warten, und versuchen Sie nicht, es in seine Bestandteile zu zerlegen. Für einige Produkte mit
austauschbaren Akkus lesen Sie bitte das Benutzerhandbuch und befolgen Sie die dort beschriebenen Anleitungen.
• Vermeiden Sie, dass Speisen oder Flüssigkeiten auf Ihr Produkt gelangen, und stecken Sie keine Gegenstände in die Gehäuseschlitze oder
-önungen Ihres Produkts.
• Verwenden Sie dieses Produkt nicht in unmittelbarer Nähe von Wasser und nicht in Bereichen mit hoher Luftfeuchtigkeit oder Kondensation,
es sei denn, es ist speziell zur Nutzung in Außenbereichen vorgesehen und eingestuft.
• Halten Sie das Produkt von Heizkörpern und anderen Quellen fern, die Wärme erzeugen.
• Trennen Sie das Produkt immer von der Stromzufuhr, bevor Sie es reinigen und verwenden Sie dazu ausschließlich ein trockenes fusselfreies
Tuch.
70D-Link DCS-4701E User Manual
Appendix B: Regulatory Information
CONSIGNES DE SÉCURITÉ
Les consignes générales de sécurité ci-après sont fournies an d’assurer votre sécurité personnelle et de protéger le produit d’éventuels
dommages. Veuillez consulter les consignes d’utilisation du produit pour plus de détails.
• L’électricité statique peut endommager les composants électroniques. Déchargez l’électricité statique de votre corps (en touchant un objet
en métal relié à la terre par exemple) avant de toucher le produit.
• N’essayez pas d’intervenir sur le produit et ne le démontez jamais. Pour certains produits contenant une batterie remplaçable par l’utilisateur,
veuillez lire et suivre les consignes contenues dans le manuel d’utilisation.
• Ne renversez pas d’aliments ou de liquide sur le produit et n’insérez jamais d’objets dans les orices.
• N’utilisez pas ce produit à proximité d’un point d’eau, de zones très humides ou de condensation sauf si le produit a été spéciquement
conçu pour une application extérieure.
• Éloignez le produit des radiateurs et autres sources de chaleur.
• Débranchez toujours le produit de l’alimentation avant de le nettoyer et utilisez uniquement un chion sec non pelucheux.
INSTRUCCIONES DE SEGURIDAD
Las siguientes directrices de seguridad general se facilitan para ayudarle a garantizar su propia seguridad personal y para proteger el producto
frente a posibles daños. No olvide consultar las instrucciones del usuario del producto para obtener más información.
• La electricidad estática puede resultar nociva para los componentes electrónicos. Descargue la electricidad estática de su cuerpo (p. ej.,
tocando algún metal sin revestimiento conectado a tierra) antes de tocar el producto.
• No intente realizar el mantenimiento del producto ni lo desmonte nunca. Para algunos productos con batería reemplazable por el usuario,
lea y siga las instrucciones del manual de usuario.
• No derrame comida o líquidos sobre el producto y nunca deje que caigan objetos en las aberturas del mismo.
• No utilice este producto cerca del agua, en zonas con humedad o condensación elevadas a menos que el producto esté clasicado
especícamente para aplicación en exteriores.
• Mantenga el producto alejado de los radiadores y de otras fuentes de calor.
• Desenchufe siempre el producto de la alimentación de red antes de limpiarlo y utilice solo un paño seco sin pelusa.
71D-Link DCS-4701E User Manual
Appendix B: Regulatory Information
ISTRUZIONI PER LA SICUREZZA
Le seguenti linee guida sulla sicurezza sono fornite per contribuire a garantire la sicurezza personale degli utenti e a proteggere il prodotto da
potenziali danni. Per maggiori dettagli, consultare le istruzioni per l’utente del prodotto.
• L’elettricità statica può essere pericolosa per i componenti elettronici. Scaricare l’elettricità statica dal corpo (ad esempio toccando una parte
metallica collegata a terra) prima di toccare il prodotto.
• Non cercare di riparare il prodotto e non smontarlo mai. Per alcuni prodotti dotati di batteria sostituibile dall’utente, leggere e seguire le
istruzioni riportate nel manuale dell’utente.
• Non versare cibi o liquidi sul prodotto e non spingere mai alcun oggetto nelle aperture del prodotto.
• Non usare questo prodotto vicino all’acqua, in aree con elevato grado di umidità o soggette a condensa a meno che il prodotto non sia
specicatamente approvato per uso in ambienti esterni.
• Tenere il prodotto lontano da caloriferi e altre fonti di calore.
• Scollegare sempre il prodotto dalla presa elettrica prima di pulirlo e usare solo un panno asciutto che non lasci lacce.
VEILIGHEIDSINFORMATIE
De volgende algemene veiligheidsinformatie werd verstrekt om uw eigen persoonlijke veiligheid te waarborgen en uw product te beschermen
tegen mogelijke schade. Denk eraan om de gebruikersinstructies van het product te raadplegen voor meer informatie.
• Statische elektriciteit kan schadelijk zijn voor elektronische componenten. Ontlaad de statische elektriciteit van uw lichaam (d.w.z. het
aanraken van geaard bloot metaal) voordat uhet product aanraakt.
• U mag nooit proberen het product te onderhouden en u mag het product nooit demonteren. Voor sommige producten met door de
gebruiker te vervangen batterij, dient u de instructies in de gebruikershandleiding te lezen en te volgen.
• Mors geen voedsel of vloeistof op uw product en u mag nooit voorwerpen in de openingen van uw product duwen.
• Gebruik dit product niet in de buurt van water, gebieden met hoge vochtigheid of condensatie, tenzij het product speciek geclassiceerd is
voor gebruik buitenshuis.
• Houd het product uit de buurt van radiators en andere warmtebronnen.
• U dient het product steeds los te koppelen van de stroom voordat u het reinigt en gebruik uitsluitend een droge pluisvrije doek.
72D-Link DCS-4701E User Manual
Appendix B: Regulatory Information
Disposing and Recycling Your Product
ENGLISH EN
This symbol on the product or packaging means that according to local laws and regulations this product should be not be disposed
of in household waste but sent for recycling. Please take it to a collection point designated by your local authorities once it has
reached the end of its life, some will accept products for free. By recycling the product and its packaging in this manner you help to
conserve the environment and protect human health.
D-Link and the Environment
At D-Link, we understand and are committed to reducing any impact our operations and products may have on the environment. To minimise
this impact D-Link designs and builds its products to be as environmentally friendly as possible, by using recyclable, low toxic materials in both
products and packaging.
D-Link recommends that you always switch o or unplug your D-Link products when they are not in use. By doing so you will help to save energy
and reduce CO2 emissions.
To learn more about our environmentally responsible products and packaging please visit www.dlinkgreen.com.
DEUTSCH DE
Dieses Symbol auf dem Produkt oder der Verpackung weist darauf hin, dass dieses Produkt gemäß bestehender örtlicher Gesetze
und Vorschriften nicht über den normalen Hausmüll entsorgt werden sollte, sondern einer Wiederverwertung zuzuführen ist. Bringen
Sie es bitte zu einer von Ihrer Kommunalbehörde entsprechend amtlich ausgewiesenen Sammelstelle, sobald das Produkt das Ende
seiner Nutzungsdauer erreicht hat. Für die Annahme solcher Produkte erheben einige dieser Stellen keine Gebühren. Durch ein auf
diese Weise durchgeführtes Recycling des Produkts und seiner Verpackung helfen Sie, die Umwelt zu schonen und die menschliche
Gesundheit zu schützen.
D-Link und die Umwelt
D-Link ist sich den möglichen Auswirkungen seiner Geschäftstätigkeiten und seiner Produkte auf die Umwelt bewusst und fühlt sich verpichtet,
diese entsprechend zu mindern. Zu diesem Zweck entwickelt und stellt D-Link seine Produkte mit dem Ziel größtmöglicher Umweltfreundlichkeit
her und verwendet wiederverwertbare, schadstoarme Materialien bei Produktherstellung und Verpackung.
D-Link empehlt, Ihre Produkte von D-Link, wenn nicht in Gebrauch, immer auszuschalten oder vom Netz zu nehmen. Auf diese Weise helfen
Sie, Energie zu sparen und CO2-Emissionen zu reduzieren.
Wenn Sie mehr über unsere umweltgerechten Produkte und Verpackungen wissen möchten, nden Sie entsprechende Informationen im Internet
unter www.dlinkgreen.com.
73D-Link DCS-4701E User Manual
Appendix B: Regulatory Information
FRANÇAIS FR
Ce symbole apposé sur le produit ou son emballage signie que, conformément aux lois et règlementations locales, ce produit ne
doit pas être éliminé avec les déchets domestiques mais recyclé. Veuillez le rapporter à un point de collecte prévu à cet eet par les
autorités locales; certains accepteront vos produits gratuitement. En recyclant le produit et son emballage de cette manière, vous
aidez à préserver l’environnement et à protéger la santé de l’homme.
D-Link et l’environnement
Chez D-Link, nous sommes conscients de l'impact de nos opérations et produits sur l'environnement et nous engageons à le réduire. Pour limiter
cet impact, D-Link conçoit et fabrique ses produits de manière aussi écologique que possible, en utilisant des matériaux recyclables et faiblement
toxiques, tant dans ses produits que ses emballages.
D-Link recommande de toujours éteindre ou débrancher vos produits D-Link lorsque vous ne les utilisez pas. Vous réaliserez ainsi des économies
d’énergie et réduirez vos émissions de CO2.
Pour en savoir plus sur les produits et emballages respectueux de l’environnement, veuillez consulter le www.dlinkgreen.com.
ESPAÑOL ES
Este símbolo en el producto o el embalaje signica que, de acuerdo con la legislación y la normativa local, este producto no se debe
desechar en la basura doméstica sino que se debe reciclar. Llévelo a un punto de recogida designado por las autoridades locales una
vez que ha llegado al n de su vida útil; algunos de ellos aceptan recogerlos de forma gratuita. Al reciclar el producto y su embalaje
de esta forma, contribuye a preservar el medio ambiente y a proteger la salud de los seres humanos.
D-Link y el medio ambiente
En D-Link, comprendemos y estamos comprometidos con la reducción del impacto que puedan tener nuestras actividades y nuestros productos
en el medio ambiente. Para reducir este impacto, D-Link diseña y fabrica sus productos para que sean lo más ecológicos posible, utilizando
materiales reciclables y de baja toxicidad tanto en los productos como en el embalaje.
D-Link recomienda apagar o desenchufar los productos D-Link cuando no se estén utilizando. Al hacerlo, contribuirá a ahorrar energía y a reducir
las emisiones de CO2.
Para obtener más información acerca de nuestros productos y embalajes ecológicos, visite el sitio www.dlinkgreen.com.
74D-Link DCS-4701E User Manual
Appendix B: Regulatory Information
ITALIANO IT
La presenza di questo simbolo sul prodotto o sulla confezione del prodotto indica che, in conformità alle leggi e alle normative locali,
questo prodotto non deve essere smaltito nei riuti domestici, ma avviato al riciclo. Una volta terminato il ciclo di vita utile, portare il
prodotto presso un punto di raccolta indicato dalle autorità locali. Alcuni questi punti di raccolta accettano gratuitamente i prodotti
da riciclare. Scegliendo di riciclare il prodotto e il relativo imballaggio, si contribuirà a preservare l'ambiente e a salvaguardare la
salute umana.
D-Link e l'ambiente
D-Link cerca da sempre di ridurre l'impatto ambientale dei propri stabilimenti e dei propri prodotti. Allo scopo di ridurre al minimo tale impatto,
D-Link progetta e realizza i propri prodotti in modo che rispettino il più possibile l'ambiente, utilizzando materiali riciclabili a basso tasso di
tossicità sia per i prodotti che per gli imballaggi.
D-Link raccomanda di spegnere sempre i prodotti D-Link o di scollegarne la spina quando non vengono utilizzati. In questo modo si contribuirà
a risparmiare energia e a ridurre le emissioni di anidride carbonica.
Per ulteriori informazioni sui prodotti e sugli imballaggi D-Link a ridotto impatto ambientale, visitate il sito all'indirizzo www.dlinkgreen.com.
NEDERLANDS NL
Dit symbool op het product of de verpakking betekent dat dit product volgens de plaatselijke wetgeving niet mag worden weggegooid
met het huishoudelijk afval, maar voor recyclage moeten worden ingeleverd. Zodra het product het einde van de levensduur heeft
bereikt, dient u het naar een inzamelpunt te brengen dat hiertoe werd aangeduid door uw plaatselijke autoriteiten, sommige
autoriteiten accepteren producten zonder dat u hiervoor dient te betalen. Door het product en de verpakking op deze manier te
recyclen helpt u het milieu en de gezondheid van de mens te beschermen.
D-Link en het milieu
Bij D-Link spannen we ons in om de impact van onze handelingen en producten op het milieu te beperken. Om deze impact te beperken, ontwerpt
en bouwt D-Link zijn producten zo milieuvriendelijk mogelijk, door het gebruik van recycleerbare producten met lage toxiciteit in product en
verpakking.
D-Link raadt aan om steeds uw D-Link producten uit te schakelen of uit de stekker te halen wanneer u ze niet gebruikt. Door dit te doen bespaart
u energie en beperkt u de CO2-emissies.
Breng een bezoek aan www.dlinkgreen.com voor meer informatie over onze milieuverantwoorde producten en verpakkingen.
75D-Link DCS-4701E User Manual
Appendix B: Regulatory Information
POLSKI PL
Ten symbol umieszczony na produkcie lub opakowaniu oznacza, że zgodnie z miejscowym prawem i lokalnymi przepisami
niniejszego produktu nie wolno wyrzucać jak odpady czy śmieci z gospodarstwa domowego, lecz należy go poddać procesowi
recyklingu. Po zakończeniu użytkowania produktu, niektóre odpowiednie do tego celu podmioty przyjmą takie produkty
nieodpłatnie, dlatego prosimy dostarczyć go do punktu zbiórki wskazanego przez lokalne władze. Poprzez proces recyklingu i
dzięki takiemu postępowaniu z produktem oraz jego opakowaniem, pomogą Państwo chronić środowisko naturalne i dbać o
ludzkie zdrowie.
D-Link i środowisko
D-Link podchodzimy w sposób świadomy do ochrony otoczenia oraz jesteśmy zaangażowani w zmniejszanie wpływu naszych działań i produktów
na środowisko naturalne. W celu zminimalizowania takiego wpływu rma D-Link konstruuje i wytwarza swoje produkty w taki sposób, aby były
one jak najbardziej przyjazne środowisku, stosując do tych celów materiały nadające się do powtórnego wykorzystania, charakteryzujące się
małą toksycznością zarówno w przypadku samych produktów jak i opakowań.
Firma D-Link zaleca, aby Państwo zawsze prawidłowo wyłączali z użytku swoje produkty D-Link, gdy nie są one wykorzystywane. Postępując w
ten sposób pozwalają Państwo oszczędzać energię i zmniejszać emisje CO2.
Aby dowiedzieć się więcej na temat produktów i opakowań mających wpływ na środowisko prosimy zapoznać się ze stroną Internetową www.
dlinkgreen.com.
ČESKY CZ
Tento symbol na výrobku nebo jeho obalu znamená, že podle místně platných předpisů se výrobek nesmí vyhazovat do komunálního
odpadu, ale odeslat k recyklaci. Až výrobek doslouží, odneste jej prosím na sběrné místo určené místními úřady k tomuto účelu.
Některá sběrná místa přijímají výrobky zdarma. Recyklací výrobku i obalu pomáháte chránit životní prostředí i lidské zdraví.
D-Link a životní prostředí
Ve společnosti D-Link jsme si vědomi vlivu našich provozů a výrobků na životní prostředí a snažíme se o minimalizaci těchto vlivů. Proto své
výrobky navrhujeme a vyrábíme tak, aby byly co nejekologičtější, a ve výrobcích i obalech používáme recyklovatelné a nízkotoxické materiály.
Společnost D-Link doporučuje, abyste své výrobky značky D-Link vypnuli nebo vytáhli ze zásuvky vždy, když je nepoužíváte. Pomůžete tak šetřit
energii a snížit emise CO2.
Více informací o našich ekologických výrobcích a obalech najdete na adrese www.dlinkgreen.com.
76D-Link DCS-4701E User Manual
Appendix B: Regulatory Information
MAGYAR HU
Ez a szimbólum a terméken vagy a csomagoláson azt jelenti, hogy a helyi törvényeknek és szabályoknak megfelelően ez a termék
nem semmisíthető meg a háztartási hulladékkal együtt, hanem újrahasznosításra kell küldeni. Kérjük, hogy a termék élettartamának
elteltét követően vigye azt a helyi hatóság által kijelölt gyűjtőhelyre. A termékek egyes helyeken ingyen elhelyezhetők. A termék és
a csomagolás újrahasznosításával segíti védeni a környezetet és az emberek egészségét.
A D-Link és a környezet
A D-Linknél megértjük és elkötelezettek vagyunk a műveleteink és termékeink környezetre gyakorolt hatásainak csökkentésére. Az ezen hatás
csökkentése érdekében a D-Link a lehető leginkább környezetbarát termékeket tervez és gyárt azáltal, hogy újrahasznosítható, alacsony károsanyag-
tartalmú termékeket gyárt és csomagolásokat alkalmaz.
A D-Link azt javasolja, hogy mindig kapcsolja ki vagy húzza ki a D-Link termékeket a tápforrásból, ha nem használja azokat. Ezzel segít az energia
megtakarításában és a széndioxid kibocsátásának csökkentésében.
Környezetbarát termékeinkről és csomagolásainkról további információkat a www.dlinkgreen.com weboldalon tudhat meg.
NORSK NO
Dette symbolet på produktet eller forpakningen betyr at dette produktet ifølge lokale lover og forskrifter ikke skal kastes sammen
med husholdningsavfall, men leveres inn til gjenvinning. Vennligst ta det til et innsamlingssted anvist av lokale myndigheter når
det er kommet til slutten av levetiden. Noen steder aksepteres produkter uten avgift. Ved på denne måten å gjenvinne produktet
og forpakningen hjelper du å verne miljøet og beskytte folks helse.
D-Link og miljøet
Hos D-Link forstår vi oss på og er forpliktet til å minske innvirkningen som vår drift og våre produkter kan ha på miljøet. For å minimalisere denne
innvirkningen designer og lager D-Link produkter som er så miljøvennlig som mulig, ved å bruke resirkulerbare, lav-toksiske materialer både i
produktene og forpakningen.
D-Link anbefaler at du alltid slår av eller frakobler D-Link-produkter når de ikke er i bruk. Ved å gjøre dette hjelper du å spare energi og å redusere
CO2-utslipp.
For mer informasjon angående våre miljøansvarlige produkter og forpakninger kan du gå til www.dlinkgreen.com.
77D-Link DCS-4701E User Manual
Appendix B: Regulatory Information
DANSK DK
Dette symbol på produktet eller emballagen betyder, at dette produkt i henhold til lokale love og regler ikke må bortskaes som
husholdningsaald, mens skal sendes til genbrug. Indlever produktet til et indsamlingssted som angivet af de lokale myndigheder,
når det er nået til slutningen af dets levetid. I nogle tilfælde vil produktet blive modtaget gratis. Ved at indlevere produktet og dets
emballage til genbrug på denne måde bidrager du til at beskytte miljøet og den menneskelige sundhed.
D-Link og miljøet
Hos D-Link forstår vi og bestræber os på at reducere enhver indvirkning, som vores aktiviteter og produkter kan have på miljøet. For at minimere
denne indvirkning designer og producerer D-Link sine produkter, så de er så miljøvenlige som muligt, ved at bruge genanvendelige materialer
med lavt giftighedsniveau i både produkter og emballage.
D-Link anbefaler, at du altid slukker eller frakobler dine D-Link-produkter, når de ikke er i brug. Ved at gøre det bidrager du til at spare energi og
reducere CO2-udledningerne.
Du kan nde ere oplysninger om vores miljømæssigt ansvarlige produkter og emballage på www.dlinkgreen.com.
SUOMI FI
Tämä symboli tuotteen pakkauksessa tarkoittaa, että paikallisten lakien ja säännösten mukaisesti tätä tuotetta ei pidä hävittää
yleisen kotitalousjätteen seassa vaan se tulee toimittaa kierrätettäväksi. Kun tuote on elinkaarensa päässä, toimita se lähimpään
viranomaisten hyväksymään kierrätyspisteeseen. Kierrättämällä käytetyn tuotteen ja sen pakkauksen autat tukemaan sekä ympäristön
että ihmisten terveyttä ja hyvinvointia.
D-Link ja ympäristö
D-Link ymmärtää ympäristönsuojelun tärkeyden ja on sitoutunut vähentämään tuotteistaan ja niiden valmistuksesta ympäristölle mahdollisesti
aiheutuvia haittavaikutuksia. Nämä negatiiviset vaikutukset minimoidakseen D-Link suunnittelee ja valmistaa tuotteensa mahdollisimman
ympäristöystävällisiksi käyttämällä kierrätettäviä, alhaisia pitoisuuksia haitallisia aineita sisältäviä materiaaleja sekä tuotteissaan että niiden
pakkauksissa.
Suosittelemme, että irrotat D-Link-tuotteesi virtalähteestä tai sammutat ne aina, kun ne eivät ole käytössä. Toimimalla näin autat säästämään
energiaa ja vähentämään hiilidioksiidipäästöjä.
Lue lisää ympäristöystävällisistä D-Link-tuotteista ja pakkauksistamme osoitteesta www.dlinkgreen.com.
78D-Link DCS-4701E User Manual
Appendix B: Regulatory Information
SVENSKA SE
Den här symbolen på produkten eller förpackningen betyder att produkten enligt lokala lagar och föreskrifter inte skall kastas i
hushållssoporna utan i stället återvinnas. Ta den vid slutet av dess livslängd till en av din lokala myndighet utsedd uppsamlingsplats,
vissa accepterar produkter utan kostnad. Genom att på detta sätt återvinna produkten och förpackningen hjälper du till att bevara
miljön och skydda människors hälsa.
D-Link och miljön
På D-Link förstår vi och är fast beslutna att minska den påverkan våra verksamheter och produkter kan ha på miljön. För att minska denna påverkan
utformar och bygger D-Link sina produkter för att de ska vara så miljövänliga som möjligt, genom att använda återvinningsbara material med
låg gifthalt i både produkter och förpackningar.
D-Link rekommenderar att du alltid stänger av eller kopplar ur dina D-Link produkter när du inte använder dem. Genom att göra detta hjälper
du till att spara energi och minska utsläpp av koldioxid.
För mer information om våra miljöansvariga produkter och förpackningar www.dlinkgreen.com.
PORTUGUÊS PT
Este símbolo no produto ou embalagem signica que, de acordo com as leis e regulamentações locais, este produto não deverá ser
eliminado juntamente com o lixo doméstico mas enviado para a reciclagem. Transporte-o para um ponto de recolha designado pelas
suas autoridades locais quando este tiver atingido o m da sua vida útil, alguns destes pontos aceitam produtos gratuitamente. Ao
reciclar o produto e respectiva embalagem desta forma, ajuda a preservar o ambiente e protege a saúde humana.
A D-Link e o ambiente
Na D-Link compreendemos e comprometemo-nos com a redução do impacto que as nossas operações e produtos possam ter no ambiente.
Para minimizar este impacto a D-Link concebe e constrói os seus produtos para que estes sejam o mais inofensivos para o ambiente possível,
utilizando meteriais recicláveis e não tóxicos tanto nos produtos como nas embalagens.
A D-Link recomenda que desligue os seus produtos D-Link quando estes não se encontrarem em utilização. Com esta acção ajudará a poupar
energia e reduzir as emissões de CO2.
Para saber mais sobre os nossos produtos e embalagens responsáveis a nível ambiental visite www.dlinkgreen.com.