Table of Contents
D-Link DCS-6010L User Manual
Displayed below is the user manual for DCS-6010L by D-Link which is a product in the Security Cameras category. This manual has pages.
User Manual
Wireless N 360° Home Network Camera
Version 1.0 | 06/06/2012
DCS-6010L
2D-Link DCS-6010L User Manual
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or
organization of such revisions or changes. Information in this document may become obsolete as our services and websites develop and
change. Please refer to the www.mydlink.com website for the most current information.
Manual Revisions
Revision Date Description
1.0 June 6, 2012 DCS-6010L Revision A1 with rmware version 1.00
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other
countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.
Copyright © 2012 D-Link Corporation.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Corporation.
Preface
3D-Link DCS-6010L User Manual
Table of Contents
Product Overview ......................................................................... 4
Package Contents ................................................................. 4
Introduction ............................................................................ 5
System Requirements ......................................................... 5
Features ....................................................................................6
Hardware Overview .............................................................7
Outside ................................................................................. 7
Internal Ports ...................................................................... 8
Installation ...................................................................................... 9
Wireless Installation Considerations ..............................9
Zero Conguration Setup ........................................................10
Camera Installation Wizard .............................................14
Manual Hardware Installation ........................................22
Mounting the Camera .......................................................23
WPS - Push Button Setup .................................................24
mydlink ...........................................................................................25
Camera Status ......................................................................26
Live Video ..............................................................................27
Playback .................................................................................28
Settings ..................................................................................29
Recording Settings .........................................................30
Advanced Settings .........................................................32
Events ......................................................................................33
Conguration ...............................................................................34
Using the Conguration Interface ................................34
Live Video ..............................................................................35
Setup .......................................................................................38
Setup Wizard ....................................................................38
Network Setup .................................................................44
Wireless Setup ..................................................................47
Dynamic DNS ...................................................................48
Image Setup .....................................................................49
Audio and Video ..............................................................51
Preset ...................................................................................53
Motion Detection ...........................................................55
Time and Date ..................................................................56
Event Setup .......................................................................57
SD Card ...............................................................................65
Advanced ...............................................................................66
HTTPS ..................................................................................66
Access List ..........................................................................67
Maintenance .........................................................................68
Device Management .....................................................68
System ................................................................................69
Firmware Upgrade ..........................................................70
Status ......................................................................................71
Device Info ........................................................................71
Logs .....................................................................................72
Help......................................................................................73
Technical Specications ...........................................................74
Safety Statements ......................................................................77
4D-Link DCS-6010L User Manual
Section 1: Product Overview
Product Overview
Package Contents
If any of the above items are missing, please contact your reseller.
Note: Using a power supply with a dierent voltage than the one included with your
product will cause damage and void the warranty for this product.
DCS-6010L Wireless N 360° Home Network Camera
CAT5 Ethernet cable
Power adapter
CD-ROM with User Manual and software
Quick Installation Guide
Mounting Bracket
5D-Link DCS-6010L User Manual
Section 1: Product Overview
Introduction
Congratulations on your purchase of the DCS-6010L Wireless N 360° Home Network Camera. The DCS-6010L is a versatile and
unique solution for your small oce or home. Unlike a standard webcam, the DCS-6010L is a complete system with a built-in
CPU and web server that transmits high quality video images for security and surveillance. The DCS-6010L can be accessed
remotely, and controlled from any PC/Notebook over your local network or through the Internet via a web browser. The simple
installation and intuitive web-based interface oers easy integration with your Ethernet/Fast Ethernet or 802.11n/g wireless
network. The DCS-6010L also comes with remote monitoring and motion detection features for a complete and cost-eective
home security solution.
• Computer with Microsoft Windows® 7, Vista®, or XP (for CD-ROM Setup Wizard), Mac OS or Linux
• PC with 1.3GHz or above; at least 128MB RAM
• Internet Explorer 7 or above , Firefox 3.5 or above, Safari 4 and Chrome 8.0 or above
• Existing 10/100 Ethernet-based network or 802.11n wireless network
• A MicroSD memory card (optional) is required for recording to onboard storage. SDHC Class 6 or above is recommended.
• Broadband Internet connection
System Requirements
6D-Link DCS-6010L User Manual
Section 1: Product Overview
360 Degree Surveillance
The built-in sheye lens gives you a full 360 degrees of coverage, allowing it to monitor an entire room with ease. It can also be placed on a wall for
180 degree coverage of a hallway. Distortion correction gives you a panoramic view or a normal corrected image that you can pan across easily.
Simple to Use
The DCS-6010L is a stand-alone system with a built-in CPU, requiring no special hardware or software. The DCS-6010L supports both ActiveX mode
for Internet Explorer and Java mode for other browsers such as Firefox® and Safari®.
Supports a Variety of Platforms
Supporting TCP/IP networking, HTTP, and other Internet related protocols. The DCS-6010L can also be integrated easily into other Internet/Intranet
applications because of its standards-based features.
802.11n Wireless or Ethernet/Fast Ethernet Support
The DCS-6010L oers wireless 802.11n and Ethernet/Fast Ethernet connectivity, making the DCS-6010L easy to integrate into your existing
network environment. The DCS-6010L works with a 10Mbps Ethernet based network or 100Mbps Fast Ethernet based network for traditional wired
environments, and works with 802.11n routers or access points for added exibility. The Site Survey feature also allows you to view and connect to
any available wireless networks.
Web Conguration
Using a standard Web browser, administrators can congure and manage the Network Camera directly from its own Web page via Intranet or
Internet. This means you can access your DCS-6010L anytime, anywhere in the world.
Broad Range of Applications
With today’s high-speed Internet services, the Network Camera can provide the ideal solution for delivering live video images over the Intranet and
Internet for remote monitoring. The Network Camera allows remote access using a Web browser for live image viewing, and allows the administrator
to manage and control the Network Camera anytime, anywhere in the world. Many applications exist, including industrial and public monitoring
of homes, oces, banks, hospitals, child-care centers, and amusement parks.
Remote Monitoring Utility
The D-ViewCam application adds enhanced features and functionality for the Network Camera and allows administrators to congure and access
the Network Camera from a remote site via Intranet or Internet. Other features include image monitoring, recording images to a hard drive, viewing
up to 32 cameras on one screen, and taking snapshots.
Features
7D-Link DCS-6010L User Manual
Section 1: Product Overview
Outside
Hardware Overview
1 Camera Lens Records video of the surrounding area
2 Camera Cover
Rotate the cover counter-clockwise to remove it and access the Ethernet port
and power connector
Caution: When removing the cover, remove it slowly to avoid disconnecting the
microphone.
3 Microphone Records audio from the surrounding area
4 MicroSD Card Slot Insert a MicroSD card for Local storage for storing recorded image and video
5 WPS Status LED Indicates the WPS connection status of the camera Indicates the camera's
current status
6 Status LED Indicates the camera's current power and connectivity status.
7 WPS Button Press this button, then press the WPS button for 5 seconds on your router to set up
a wireless connection automatically
8 Reset Button Press and hold this button for 10 seconds to reset the camera
5
6
4
3
1
7
8
2
8D-Link DCS-6010L User Manual
Section 1: Product Overview
Internal Ports
You can access the inside of the DCS-6010L by rotating the camera cover counter-clockwise, then lifting it o of the camera.
Caution: When removing the cover, remove it slowly to avoid disconnecting the microphone.
1 Ethernet Cable Pre-attached Ethernet cable.
2 Power Cable Pre-attached power cable.
9D-Link DCS-6010L User Manual
Section 2: Installation
This D-Link device can connect to your wireless network from anywhere within the operating range of your wireless network. However, the number,
thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary
depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range
is to follow these basic guidelines:
1. Minimize the number of walls and ceilings between your adapter and other network devices (such as your Network Camera) - each wall or
ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters).
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle appears to be almost 3 feet
(1 meter) thick. At a 2-degree angle, it looks over 42 feet (14 meters) thick. Position your devices so that the signal will travel straight through
a wall or ceiling (instead of at an angle) for better reception.
3. Building Materials make a dierence. A solid metal door or aluminum studs may weaken the wireless signal. Try to position your access points,
wireless routers, and other networking devices where the signal passes through drywall or open doorways. Materials and objects such as
glass, steel, metal, walls with insulation, water (sh tanks), mirrors, le cabinets, brick, and concrete will degrade your wireless signal.
4. Keep your product at least 3-6 feet or 1-2 meters away from electrical devices or appliances that generate RF noise.
5. If you are using 2.4GHz cordless phones or other radio frequency sources (such as microwave ovens), your wireless connection may degrade
dramatically or drop completely. Make sure your 2.4GHz phone base is as far away from your wireless devices as possible. The base transmits
a signal even if the phone in not in use.
Installation
Wireless Installation Considerations
10D-Link DCS-6010L User Manual
Section 2: Installation
If you have a mydlink-enabled Cloud Router, you can take advantage of Zero Conguration. Zero Conguration automatically
congures your camera's settings for you, and adds it to your mydlink account automatically. This type of setup allows you to
set up your camera by simply plugging it in and connecting it to your router.
Connect your camera to your mydlink-enabled Cloud Router and Zero Conguration will automatically congure your DCS-6010L
and automatically add the camera to your mydlink account. After the short time it takes to do this you can remotely access
your camera from the www.mydlink.com website to manage and monitor your DCS-6010L.
Connect the Ethernet Cable
Using the pre-attached Ethernet cable connect the free-end to your network.
To use a longer ethernet cable or install a coupling adaptor, or see "Internal Ports"
on page 8 for more details. for how to change the Ethernet cable.
Attach the External Power Supply
Attach the external power supply to your wall outlet or power strip.
Zero Conguration Setup
2
1 Ethernet Cable Pre attached Ethernet cable
2 Power Cable Pre attached power cable.
1
11D-Link DCS-6010L User Manual
Section 2: Installation
To create a WPS connection:
Step 1
Press and hold the WPS button for approximately 5-6 seconds. The WPS LED will
blink.
Step 2
Within 60 seconds press the WPS button on your router. On some routers, you
may need to log in to the web interface and click on an on-screen button to
activate the WPS feature. If you are not sure where the WPS button is on your
router, please refer to your router’s User Manual.
The DCS-6010L will automatically create a wireless connection to your router.
While connecting, the status LED will ash. When the connection process is
complete, the status LED will turn solid.
You can now remove the pre-attached Ethernet cable by removing the camera
cover and disconnecting the Ethernet cable. See "Internal Ports" on page 8 for
more details.
Note: If your router does not support WPS, you can still use the wired connection
method on the previous page. After Zero Conguration setup is complete, your
router's wireless settings will be automatically transferred to the camera.
Optional: WPS Wireless Connection
Alternatively, if your router supports WPS, you can use the WPS button on the
camera to easily create a secure wireless connection to your network.
WPS ButtonWPS LED
12D-Link DCS-6010L User Manual
Section 2: Installation
A summary and conrmation notication will appear with the automatically
congured details. Make a note of the details and click OK to add the camera to
your account.
Check Your mydlink Account
From any computer, open a web browser, go to http://www.mydlink.com and log
into your account. Once mydlink detects your camera, a New Device Found!
notice will appear in the bottom-left corner. Click on the device name to continue.
13D-Link DCS-6010L User Manual
Section 2: Installation
Zero Conguration is now complete and your camera has been added to your
mydlink account. You can now view your camera on the mydlink Live View tab.
If you wish to connect your camera to your router wirelessly, you can simply
disconnect the Ethernet cable and move the camera to its intended location; your
router's wireless settings have been automatically transferred to the camera, and
no further conguration is required.
Your camera is now set up, and you can skip to "mydlink" on page 25 to learn more
about the mydlink features of this camera, or to "Conguration" on page 34 for
advanced conguration of your camera.
14D-Link DCS-6010L User Manual
Section 2: Installation
Insert the Installation CD-ROM into your computer’s optical drive to start the autorun program.
The CD-ROM will open the Camera Installation Wizard. Simply click Setup Your Camera to go through the Installation Wizard,
which will guide you through the installation process from connecting your hardware to conguring your camera.
Camera Installation Wizard
15D-Link DCS-6010L User Manual
Section 2: Installation
Connect the included Ethernet cable to the internal network cable connector of
the DCS-6010L and attach it to the network.
Click Next to continue.
Select your preferred language for the installation from the drop down menu
and click on Start to continue.
16D-Link DCS-6010L User Manual
Section 2: Installation
Connect the other end of the same Ethernet cable to a router.
Click Next to continue.
Attach the external power supply to the power connector located inside the
DCS-6010L and connect it to your wall outlet or power strip.
Click Next to continue.
17D-Link DCS-6010L User Manual
Section 2: Installation
The LED on the front of the DCS-6010L will blink, then turn solid green once it
successfully connects to your network. Click Next to proceed.
If the LED continues to stay red, check your connections or click on the "What
should I do if the LED stays red?" link for more information.
Select your camera from the list, then click Next. If you have multiple cameras, you
can identify them by the MAC ID printed on the label on the back of your camera.
18D-Link DCS-6010L User Manual
Section 2: Installation
If you wish to remove the camera from a previously registered mydlink account,
press and hold the reset button on the rear panel for at least 10 seconds and click
Restart to restart the wizard.
After you have selected your camera from the list, you will be asked to create
and conrm a password for it. The password is case sensitive and must contain
at least 2 letters.
Click Next to continue.
19D-Link DCS-6010L User Manual
Section 2: Installation
To move the camera to a wireless connection by using WPS or by selecting a
wireless network, select the appropriate option then follow the steps displayed.
Otherwise, click Next to continue.
Complete the mydlink account registration form with your details making sure to
select the I accept mydlink terms and conditions box, and click the Next button.
20D-Link DCS-6010L User Manual
Section 2: Installation
If you already have a mydlink account, enter your login details and click Next to
proceed.
Conrm your mydlink account details and give the camera a unique name and
click Done.
21D-Link DCS-6010L User Manual
Section 2: Installation
Conrm your camera login details and IP address details and click Done.
Your DCS-6010L camera is now set up. Log on to your mydlink account and
explore the exciting benets available to you.
Your camera is now set up, and you can skip to "mydlink" on page 25 to learn more
about the mydlink features of this camera, or to "Conguration" on page 34 for
advanced conguration of your camera.
22D-Link DCS-6010L User Manual
Section 2: Installation
Manual Hardware Installation
If you wish to set up your camera without using the Camera Setup Wizard, please follow these steps.
Note: In order to use the mydlink features of this product, you will need to go through the Camera Setup Wizard.
Connect the Ethernet Cable
Using the pre-attached Ethernet cable connect the free end to your network.
To use a longer ethernet cable or install a coupling adaptor, or see "Internal Ports"
on page 8 for more details. for how to change the Ethernet cable.
Attach the External Power Supply
Attach the external power supply to your wall outlet or power strip.
2
1
1 Ethernet Cable Pre attached Ethernet cable
2 Power Cable Pre attached power cable.
23D-Link DCS-6010L User Manual
Section 2: Installation
Mounting the Camera
The DCS-6010L is suitable for mounting to a ceiling, wall or desktop using the bracket provided.
Note: In order to use the mydlink features of this product, you will need to go through the Camera Setup Wizard.
Step 1
Unclip the wall bracket from the DCS-6010L by sliding the base down.
Step 2
Position the mounting bracket in the desired location and mark the surface
behind it holes using the bracket as a stencil / in pencil
Step 3
Use a 6mm drill bit to make required holes approximately 25mm deep.
Step 4
Insert wall anchors.
Step 5
Ax bracket using the screws provided.
Step 6
Clip the DCS-6010L to the bracket ensuring a tight t
Note: if mounting on a wall ensure the camera is oriented with the cables
positioned to the bottom of the device.
1
24D-Link DCS-6010L User Manual
Section 2: Installation
WPS - Push Button Setup
If your router supports WPS, you can use the WPS button on the camera to easily create a secure wireless connection to your
network.
To create a WPS connection:
Step 1
Press and hold the WPS button for approximately 5-6 seconds. The WPS LED will
blink.
Step 2
Within 60 seconds press the WPS button on your router. On some routers, you
may need to log in to the web interface and click on an on-screen button to
activate the WPS feature. If you are not sure where the WPS button is on your
router, please refer to your router’s User Manual.
The DCS-6010L will automatically create a wireless connection to your router.
While connecting, the status LED will ash. When the connection process is
complete, the status LED will turn solid.
Note: If your router does not support WPS, you can still use the wired connection
method on the previous page.
WPS ButtonWPS LED
25D-Link DCS-6010L User Manual
Section 3: mydlink
mydlink
After registering your DCS-6010L camera with a mydlink account in the Camera Installation Wizard. You will be able to remotely
access your camera from the www.mydlink.com website. After signing in to your mydlink account, you will see a screen similar
to the following:
Note: The above screenshot is representative only. The mydlink website is constantly improving and so may appear dierent.
26D-Link DCS-6010L User Manual
Section 3: mydlink
Camera Status
If your camera is oine, try the following:
• Check to make sure that the Internet connection to your camera is working properly.
• Try restarting your Internet router.
• Check your camera’s Ethernet and power cable connections and make sure they are secure.
• Check to make sure that the LED on your camera is lit solid green.
If you still cannot access your camera, reset your camera and run the Camera Installation Wizard again from the CD-ROM
included in your package.
Here, you can see the online status of each of your cameras. Your online status may be one of the following:
A red X indicates that your camera is oine and currently cannot be accessed remotely.
A green checkmark indicates that your camera is online and ready to use.
A yellow exclamation point indicates that your camera is online, but the camera password
has changed. You will need to enter your new camera password to access your camera
again.
27D-Link DCS-6010L User Manual
Section 3: mydlink
Live Video
In the main part of the screen, the Live Video tab will be selected by default. If
the camera is available, a Live Video feed will be displayed. Video will be shown
at VGA resolution (640x480) if viewing your camera from a PC on the same local
network, or at QVGA resolution (320x240) if viewing your camera from a PC on
a remote network.
View Mode Here, you can select between the dierent view modes:
Fisheye Mode: shows the full camera view.
Normal Mode: shows a corrected view similar to a
standard camera view that you can move using the
control pad.
Panoramic Mode: This shows a corrected, full 180
view across 2 video panels.
Multi-View with Fisheye: This shows a multiple
window view, with a full sheye view in the top-
right panel.
Multi-View: This shows a multiple window view.
Brightness Adjust the slider control to account for brightness.
Zoom Adjust the slider control to zoom in or out.
28D-Link DCS-6010L User Manual
Section 3: mydlink
Playback
Select the date of the footage you wish to preview from the drop down menu,
then choose from the recordings available for playback.
The Playback tab allows you to review pre-recorded footage captured to an
inserted microSD card.
29D-Link DCS-6010L User Manual
Section 3: mydlink
Settings
The Settings tab contains several options for you to control how your DCS-6010L operates.
Click on the Edit button to change how the camera name appears.
This is the unique mydlink number for your device.
This shows the model name of the camera.
The shows the Media Access Control (MAC) address of the camera.
The date the camera was registered to the mydlink service.
E-mail notication of events can be switched on or o.
Camera Name:
mydlink No:
Model name:
MAC:
Camera Activated on:
Event Notication
Settings:
Each of the recording settings will open a further menu.Recording Settings:
30D-Link DCS-6010L User Manual
Section 3: mydlink
Select this option to enable the automatic recording when motion
is detected.
Add Detection Area: Click on this icon to draw areas that
will trigger automatic recording when motion is detected.
Remove Detection Area: Click on this icon to erase areas
from regions that trigger automatic recording when
motion is detected.
Clear Detection Area: This will remove all detection areas
Refresh Snapshot: This will refresh the current snapshot
of the monitored area.
Increase/Decrease Sensitivity Increase the motion
detection sensitivity
Toggles notication by email on or o.
In the event that the microSD card can not store further recordings,
the user can choose to record over previous recordings or to be
notied and cease recording.
Record video clips
when motion is
detected:
Email Notication:
Video Clips Recording
Mode:
Recording Settings
31D-Link DCS-6010L User Manual
Section 3: mydlink
Toggles notication by email on or o.Email Notication:
This option enables either continuous or recurring scheduled
recording.
Record Video Clips by
Schedule:
In the event that the microSD card can not store further recordings,
the user can choose to record over previous recordings or to be
notied and cease recording.
Video Clips Recording
Mode:
32D-Link DCS-6010L User Manual
Section 3: mydlink
Checking this box will show the password.Show password:
Advanced Settings
Clicking on the Advanced Setting button will open a secondary
window allowing full conguration of the DCS-6010L
Advanced Setting:
33D-Link DCS-6010L User Manual
Section 3: mydlink
Events
Select from the available options to manage your event log.
Mark Page as Read: Clicking this button will mark the
current page of event notications as read.
Mark all as Read: Clicking this button will mark all event
notications as read.
The Events tab contains options for you to keep track of your DCS-6010L event notications.
34D-Link DCS-6010L User Manual
Section 4: Conguration
Conguration
Using the Conguration Interface
After completing the Camera Installation Wizard, you are ready to use your camera. The camera’s built-in Web conguration utility is designed to
allow you to easily access and congure your DCS-6010L. At the end of the wizard, click Go To Camera, or enter the IP address of your camera into
a web browser, such as Mozilla Firefox. To log in, use the User name admin and the password you created in the Installation Wizard. If you did not
create a password, the default password is blank. After entering your password, click OK.
35D-Link DCS-6010L User Manual
Section 4: Conguration
Live Video
This section shows your camera’s live video. You may select any of the available icons listed below to operate the camera. You may also select your
language using the drop-down menu on the left side of the screen.
You can zoom in and out on the live video image using your mouse. Right-click to zoom out or left-click to zoom in on the image.
Motion Trigger
Indicator
This indicator will change color when a trigger event
occurs.
Note: The video motion feature for your camera must be
enabled.
Recording
Indicator
When a recording is in progress, this indicator will change
color.
Control Pad
This control pad can be used to electronically pan, tilt, and
zoom (ePTZ) within the camera's predened view area, if
one has been dened.
Auto Pan
Click this button to start the automated circular rotation
through a regional view (360* continuous rotation).
Note: This function does not apply in a Panoramic view
because a panoramic view already shows the full coverage.
Stop Click this button to stop the Auto Pano and Auto Rotate
functions.
Preset Path
Once you have determined a list of preset PTZ positions, click
this button to consecutively display views of these positions.
The DCS-6010L will display these views continuously. For
more information please refer to "Preset" on page 53
This option displays the status of the SD card. If no SD card has been
inserted, this screen will display the message "Card Invalid."
SD Status:
36D-Link DCS-6010L User Manual
Section 4: Conguration
You can set the speed of pan/tilt/zoom/auto pan movement and
sequence changes by using the dropdown menus.
You may select the interface language using this menu.
Pan/Tilt/Zoom/
Auto Pan/
Sequence
Speed:
Language:
Display Mode Here, you can select between the dierent display modes:
Fisheye Mode: shows the full camera view
Normal Mode: shows a corrected view similar to a
standard camera view that you can move using the
control pad.
Panoramic Mode: This shows a corrected, full 180
view across 2 video panels.
Multi-View with Fisheye: This shows a multiple
window view, with a full Fisheye view in the top-
right panel.
Multi-View: This shows a multiple window view.
37D-Link DCS-6010L User Manual
Section 4: Conguration
If any presets have been dened, selecting a preset from this list will
display it.
Go To:
(Preset List)
Video Prole 1
Video Prole 2
Video Prole 3
Full screen mode
Take a Snapshot
Record a Video Clip
Set a Storage Folder
Listen/Stop Audio In (from microphone)
Start/Stop Audio Out (to speaker)
38D-Link DCS-6010L User Manual
Section 4: Conguration
Setup
Setup Wizard
To congure your Network Camera, click Internet Connection Setup Wizard. Alternatively,
you may click Manual Internet Connection Setup to manually congure your Network
Camera and skip to "Network Setup" on page 44.
To quickly congure your Network Camera’s motion detection settings, click Motion
Detection Setup Wizard. If you want to enter your settings without running the wizard, click
Manual Motion Detection Setup and skip to"Motion Detection" on page 55.
39D-Link DCS-6010L User Manual
Section 4: Conguration
Internet Connection Setup Wizard
This wizard will guide you through a step-by-step process to congure your new D-Link
Camera and connect the camera to the internet. Click Next to continue.
Note: Select DHCP if you are unsure of which settings to choose.
Click Next to continue.
40D-Link DCS-6010L User Manual
Section 4: Conguration
Select Static IP if your Internet Service Provider has provided you with connection settings, or
if you wish to set a static address within your home network. Enter the correct conguration
information and click Next to continue.
If you are using PPPoE, select Enable PPPoE and enter your user name and password,
otherwise click Next to continue.
If you have a Dynamic DNS account and would like the camera to update your IP address
automatically, Select Enable DDNS and enter your host information. Click Next to continue.
Enter a name for your camera and click Next to continue.
41D-Link DCS-6010L User Manual
Section 4: Conguration
Congure the correct time to ensure that all events will be triggered as scheduled. Click Next
to continue.
Conrm the settings are correct and click Apply to save them..
The settings will be saved to the DCS-6010L and the camera will restart.
42D-Link DCS-6010L User Manual
Section 4: Conguration
This wizard will guide you through a step-by-step process to congure your camera's
motion detection functions.
Click Next to continue.
Motion Detection Setup Wizard
Step 1
This step will allow you to enable or disable motion detection, specify the detection sensitivity,
and adjust the camera’s ability to detect movement.
You may specify whether the camera should capture a snapshot or a video clip when motion
is detected.
Please see the Motion Detection section on "Motion Detection" on page 55for information
about how to congure motion detection.
Step 2
This step allows you to enable motion detection based on a customized schedule. Specify the
day and hours. You may also choose to always record whenever motion is detected.
43D-Link DCS-6010L User Manual
Section 4: Conguration
Step 3
This step allows you to specify how you will receive event notications from your camera. You
may choose not to receive notications, or to receive notications via e-mail or FTP.
Please enter the relevant information for your e-mail or FTP account.
Click Next to continue.
Step 4
You have completed the Motion Detection Wizard.
Please verify your settings and click Apply to save them.
Please wait a few moments while the camera saves your settings and restarts.
44D-Link DCS-6010L User Manual
Section 4: Conguration
Network Setup
Use this section to congure the network connections for your camera. All relevant information must be entered accurately. After making any
changes, click the Save Settings button to save your changes.
LAN Settings:
DHCP:
Static IP Client:
IP Address:
Subnet Mask:
Default Gateway:
Primary DNS:
Secondary DNS:
This section lets you congure settings for your local
area network.
Select this connection if you have a DHCP server running
on your network and would like your camera to obtain
an IP address automatically.
If you choose DHCP, you do not need to ll out the IP
address settings.
You may obtain a static or xed IP address and other
network information from your network administrator
for your camera. A static IP address may simplify access
to your camera in the future.
Enter the xed IP address in this eld.
This number is used to determine if the destination is in
the same subnet. The default value is 255.255.255.0.
The gateway used to forward frames to destinations in a
dierent subnet. Invalid gateway settings may cause the
failure of transmissions to a dierent subnet.
The primary domain name server translates names to IP
addresses.
The secondary DNS acts as a backup to the primary DNS.
45D-Link DCS-6010L User Manual
Section 4: Conguration
Enable UPnP Presentation:
Enable UPnP Port Forwarding:
Enable PPPoE:
User Name / Password:
HTTP Port:
Access Name for Stream 1~3:
HTTPS Port:
RTSP Port:
Enabling this setting allows your camera to be congured
as a UPnP device on your network.
Enabling this setting allows the camera to add port
forwarding entries into the router automatically on a
UPnP capable network.
Enable this setting if your network uses PPPoE.
Enter the username and password for your PPPoE
account. Re-enter your password in the Conrm
Password eld. You may obtain this information from
your ISP.
The default port number is 80.
The default name is video#.mjpg, where # is the number
of the stream.
You may use a PC with a secure browser to connect to
the HTTPS port of the camera. The default port number
is 443.
The port number that you use for RTSP streaming to
mobile devices, such as mobile phones or PDAs. The
default port number is 554. You may specify the address
of a particular stream. For instance, live1.sdp can be
accessed at rtsp://x.x.x.x/video1.sdp where the x.x.x.x
represents the ip address of your camera.
46D-Link DCS-6010L User Manual
Section 4: Conguration
Enable CoS:
Enable QoS:
Enable IPV6:
Enable Multicast for stream
Enabling the Class of Service setting implements a
best-eort policy without making any bandwidth
reservations.
Enabling QoS allows you to specify a trac priority
policy to ensure a consistent Quality of Service during
busy periods. If the Network Camera is connected to a
router that itself implements QoS, the router's settings
will override the QoS settings of the camera.
Enable the IPV6 setting to use the IPV6 protocol. Enabling
the option allows you to manually set up the address,
specify an optional IP address, specify an optional router
and an optional primary DNS.
The DCS-6010L allows you to multicast each of the
available streams via group address and specify the TTL
value for each stream. Enter the port and TTL settings
you wish to use if you do not want to use the defaults.
47D-Link DCS-6010L User Manual
Section 4: Conguration
Wireless Setup
This section allows you to set up and congure the wireless settings on your camera. After making any changes, click the Save Settings button to
save your changes.
Site Survey:
SSID:
Wireless Mode:
Channel:
Authentication:
Encryption:
Key:
Click the Rescan button to scan for available wireless
networks. After scanning, you can use the drop-down
box to select an available wireless network. The related
information (SSID, Wireless Mode, Channel, Authentication,
Encryption) will be automatically lled in for you.
Enter the SSID of the wireless access point you wish to
use.
Use the drop-down box to select the mode of the
wireless network you wish to connect to. Infrastructure
is normally used to connect to an access point or router.
Ad-Hoc is usually used to connect directly to another
computer.
If you are using Ad Hoc mode, select the channel of the
wireless network you wish to connect to, or select Auto.
Select the authentication you use on your wireless
network - Open, Shared, WPA-PSK, or WPA2-PSK.
If you use WPA-PSK or WPA2-PSK authentication, you
will need to specify whether your wireless network
uses TKIP or AES encryption. If you use Open or Shared
authentication, WEP encryption should be the setting.
If you use WEP, WPA-PSK, or WPA2-PSK authentication,
enter the Key (also known as password) used for your
wireless network.
48D-Link DCS-6010L User Manual
Section 4: Conguration
Dynamic DNS
DDNS (Dynamic Domain Name Server) will hold a DNS host name and synchronize the public IP address of the modem when it has been modied.
A user name and password are required when using the DDNS service. After making any changes, click the Save Settings button to save your
changes.
Enable DDNS:
Server Address:
Host Name:
User Name:
Password:
Timeout:
Status:
Select this checkbox to enable the DDNS function.
Select your Dynamic DNS provider from the pull down
menu or enter the server address manually.
Enter the host name of the DDNS server.
Enter the user name or e-mail used to connect to your
DDNS account.
Enter the password used to connect to your DDNS
server account.
Enter the DNS timeout values you wish to use.
Indicates the connection status, which is automatically
determined by the system.
49D-Link DCS-6010L User Manual
Section 4: Conguration
Image Setup
In this section, you may congure the video image settings for your camera. A preview of the image will be shown in Live Video.
Mirror:
Flip:
Power Line:
White Balance:
Exposure Mode:
Denoise:
Brightness:
This will mirror the image horizontally.
This will ip the image vertically. When turning Flip on,
you may want to consider turning Mirror on as well.
Select the frequency used by your power lines to avoid
interference or distortion.
Use the drop-down box to change white balance settings
to help balance colors for dierent environments. You
can choose from Auto, Outdoor, Indoor, Fluorescent,
and Push Hold.
Changes the exposure mode. Use the drop-down
box to set the camera for Indoor, Outdoor, or Night
environments, or to Moving to capture moving objects.
The Low Noise option will focus on creating a high-
quality picture without noise. You can also create 3
dierent custom exposure modes. The Max Gain setting
will allow you to control the maximum amount of gain
to apply to brighten the picture.
This setting controls the amount of noise reduction that
will be applied to the picture.
Adjust this setting to compensate for backlit subjects.
50D-Link DCS-6010L User Manual
Section 4: Conguration
Contrast:
Saturation:
Sharpness:
Reset Default
Mounting:
Adjust this setting to alter the color intensity/strength.
This setting controls the amount of coloration, from
grayscale to fully saturated.
Specify a value from 0 to 8 to specify how much
sharpening to apply to the image.
Click this button to reset the image to factory default
settings.
Select the correct mounting type from either Ceiling, Wall,
or Desktop to ensure the PTZ controls respond accurately.
51D-Link DCS-6010L User Manual
Section 4: Conguration
Audio and Video
You may congure up to 3 video proles with dierent settings for your camera. Hence, you may set up dierent proles for your computer and
mobile display. In addition, you may also congure the two-way audio settings for your camera. After making any changes, click the Save Settings
button to save your changes.
Number of active proles:
Aspect ratio:
Mode:
Frame size / View window area:
Maximum frame rate:
Video Quality:
Constant bit rate:
You can use the drop-down box to set up to 2 active
proles.
Set the aspect ratio of the video to 4:3 standard or 16:9
widescreen.
Set the video codec to be used to JPEG, MPEG-4, or
H.264.
TBD 1600 x 1200, 1200 x 900, 800 x 600, 400 x 300
A higher frame rate provides smoother motion for
videos, and requires more bandwidth. Lower frame
rates will result in stuttering motion, and requires less
bandwidth.
This limits the maximum frame rate, which can be
combined with the "Fixed quality" option to optimize
the bandwidth utilization and video quality. If xed
bandwidth utilization is desired regardless of the video
quality, choose "Constant bit rate" and select the desired
bandwidth.
The bps will aect the bit rate of the video recorded
by the camera. Higher bit rates result in higher video
quality.
52D-Link DCS-6010L User Manual
Section 4: Conguration
Fixed quality:
Encoding
Audio in o:
Audio in gain level:
Audio out o:
Audio out volume level:
Select the image quality level for the camera to try to
maintain. High quality levels will result in increased bit
rates.
Choose between G.726 or G.711
Selecting this checkbox will mute incoming audio.
This setting controls the amount of gain applied to
incoming audio to increase its volume.
Selecting this checkbox will mute outgoing audio.
This setting controls the amount of gain applied to
outgoing audio to increase its volume.
53D-Link DCS-6010L User Manual
Section 4: Conguration
Preset
This page allows you to set preset points for the ePTZ function of the camera, which allows you to look around the camera's viewable area by using
a zoomed view. Presets allow you to quickly go to and view a specic part of the area your camera is covering, and you can create preset sequences,
which will automatically change the camera's view between the dierent presets according to a dened order and timing you can set.
Video Prole:
Arrow Buttons and Home Button:
Input Preset Name:
Preset List:
Preset Sequence:
This selects which video prole to use.
Use these buttons to move to a specic part of the
viewing area, which you can then set as a preset. Click
the Home button to return to the center of the viewing
area.
Enter the name of the preset you want to create, then
click the Add button to make a new preset. If an existing
preset has been selected from the Preset List, you can
change its name by typing in a new name, then clicking
the Rename button.
Click this drop-down box to see a list of all the presets
that have been created. You can select one, then click
the GoTo button to change the displayed camera view
to the preset. Clicking the Remove button will delete
the currently selected preset.
This section allows you to create a preset sequence,
which automatically moves the camera's view between
a set of preset views.
The page displays 2 video panes. The left pane shows the zoomed view, the right pane shows the entire viewable area. Select a video prole from
the dropdown menu to work with, then click and drag within either pane to control the viewing area. Use the arrow buttons to ne tune the area
you wish to focus on.
54D-Link DCS-6010L User Manual
Section 4: Conguration
Preset List: To add a preset to the sequence, select it from the drop-
down box at the bottom of this window, set the Dwell
time to determine how long the camera view will stay at
that preset, then click the Add button. The preset name
will appear in the list, followed by the dwell time to view
that preset for.
You can rearrange your presets in the sequence by
selecting a preset in the sequence, then clicking the
arrow buttons to move it higher or lower in the current
sequence.
Clicking the trash can button will remove the currently
selected preset from the sequence.
If you want to change the dwell time for a preset, select
it from the list, enter a new dwell time, then click the
Update button.
55D-Link DCS-6010L User Manual
Section 4: Conguration
Motion Detection
Enabling Video Motion will allow your camera to use the motion detection feature. You may draw a nite motion area that will be used for
monitoring. After making any changes, click the Save Settings button to save your changes.
Enable Video Motion:
Sensitivity:
Percentage:
Draw Motion Area:
Erase Motion Area:
Select this box to enable the motion detection feature
of your camera.
Species the measurable dierence between two
sequential images that would indicate motion. Please
enter a value between 0 and 100.
Species the amount of motion in the window being
monitored that is required to initiate an alert. If this is set
to 100%, motion is detected within the whole window
will trigger a snapshot.
Draw the motion detection area by dragging your mouse
in the window (indicated by the red square).
To erase a motion detection area, simply click on the red
square that you wish to remove.
Right clicking on the camera image brings up the
following menu options:
Select All: Draws a motion detection area over the
entire screen.
Clear All: Clears any motion detection areas that have
been drawn.
Restore: Restores the previously specied motion
detection areas.
56D-Link DCS-6010L User Manual
Section 4: Conguration
Time and Date
This section allows you to automatically or manually congure, update, and maintain the internal system clock for your camera. After making any
changes, click the Save Settings button to save your changes.
Time Zone:
Enable Daylight Saving:
Auto Daylight Saving:
Set Date and Time Manually:
Oset:
Synchronize with NTP Server:
NTP Server:
Set the Date and Time Manually:
Copy Your Computer's Time
Settings:
Select your time zone from the drop-down menu.
Select this to enable Daylight Saving Time.
Select this option to allow your camera to congure the
Daylight Saving settings automatically.
Selecting this option allows you to congure the Daylight
Saving date and time manually.
Sets the amount of time to be added or removed when
Daylight Saving is enabled.
Enable this feature to obtain time automatically from an
NTP server.
Network Time Protocol (NTP) synchronizes the
DCS-6010L with an Internet time server. Choose the one
that is closest to your location.
This option allows you to set the time and date manually.
This will synchronize the time information from your PC.
57D-Link DCS-6010L User Manual
Section 4: Conguration
Event Setup
In a typical application, when motion is detected, the DCS-6010L sends images to a FTP server or via e-mail as notications. As shown in the
illustration below, an event can be triggered by many sources, such as motion detection. When an event is triggered, a specied action will be
performed. You can congure the Network Camera to send snapshots or videos to your e-mail address or FTP site.
To start plotting an event, it is suggested to congure server and media columns rst so that the Network Camera will know what action shall be
performed when a trigger is activated.
58D-Link DCS-6010L User Manual
Section 4: Conguration
The Event Setup page includes 4 dierent sections.
• Event
• Server
• Media
• Recording
1. To add a new item - "event, server or media," click Add. A screen will appear and allow you
to update the elds accordingly.
2. To delete the selected item from the pull-down menu of event, server or media, click Delete.
3. Click on the item name to pop up a window for modifying.
59D-Link DCS-6010L User Manual
Section 4: Conguration
Add Server
Server Name:
E-mail:
FTP:
Network Storage:
SD Card:
Enter the unique name of your server.
Enter the conguration for the target e-mail server
account.
Enter the conguration for the target FTP server account.
Specify a network storage device. Only one network
storage device is supported.
Use the camera's onboard SD card storage.
You can congure up to 5 servers to save snapshots and/or video to. After making any
changes, click the Save Settings button to save your changes.
60D-Link DCS-6010L User Manual
Section 4: Conguration
Add Media
Media Name:
Snapshot:
Source:
Send pre-event image(s) [0~4]:
Send post-event image(s) [0~7]:
File name prex:
Add date and time sux to le
name:
Enter a unique name for media type you want to create.
Select this option to set the media type to snapshots.
Set the video prole to use as the media source. Refer
to Audio and Video on "Audio and Video" on page 51 for
more information on video proles.
Set the number of pre-event images to take. Pre-event
images are images taken before the main event snapshot
is taken.
Set the number of post-event images to take. Post-event
images are images taken after the main event snapshot
is taken. You can set up to 7 post-event images to be
taken.
The prex name will be added on the le name.
Check it to add timing information as le name sux.
There are three types of media, Snapshot, Video Clip, and System Log. After making any
changes, click the Save Settings button to save your changes.
61D-Link DCS-6010L User Manual
Section 4: Conguration
Video clip:
Source:
Pre-event recording:
Maximum duration:
Maximum le size:
File name prex:
System log:
Select this option to set the media type to video clips.
Set the video prole to use as the media source. Refer to
"Audio and Video" on page 46 for more information on
video proles.
This sets how many seconds to record before the main
event video clip starts. You can record up to 4 seconds of
pre-event video.
Set the maximum length of video to record for your
video clips.
Set the maximum le size to record for your video clips.
This is the prex that will be added to the lename of
saved video clips.
Select this option to set the media type to system logs.
This will save the event to the camera system log, but
will not record any snapshots or video.
62D-Link DCS-6010L User Manual
Section 4: Conguration
Add Event
Create and schedule up to 2 events with their own settings here. After making any changes,
click the Save Settings button to save your changes.
Event name:
Enable this event:
Priority:
Delay:
Trigger:
Video Motion Detection:
Periodic:
System Boot:
Network Lost:
Passive Infrared Sensor:
Time:
Server:
Enter a name for the event.
Select this box to activate this event.
Set the priority for this event. The event with higher
priority will be executed rst.
Select the delay time before checking the next event. It is
used for motion detection events.
Specify the input type that triggers the event.
Motion is detected during live video monitoring. Select
the windows that need to be monitored.
The event is triggered in specied intervals. The trigger
interval unit is in minutes.
Triggers an event when the system boots up.
Triggers an event when the network connection is lost.
Triggers an event when the PIR sensor is activated by
moving infrared objects even in dark environment.
Select Always or enter the time interval.
Specify the location where the event information should
be saved to.
63D-Link DCS-6010L User Manual
Section 4: Conguration
Add Recording
Recording entry name:
Enable this recording:
Priority:
Source:
Recording schedule:
Recording settings:
Destination:
Total cycling recording size:
The unique name of the entry.
Select this to enable the recording function.
Set the priority for this entry. The entry with a higher
priority value will be executed rst.
The source of the stream.
Scheduling the recording entry.
Conguring the setting for the recording.
Select the folder where the recording le will be stored.
Please input a HDD volume between 1MB and 2TB for
recording space. The recording data will replace the
oldest record when the total recording size exceeds this
value. For example, if each recording le is 6MB, and the
total cyclical recording size is 600MB, then the camera
will record 100 les in the specied location (folder) and
then will delete the oldest le and create new le for
cyclical recording.
Please note that if the free HDD space is not enough, the
recording will stop. Before you set up this option please
make sure your HDD has enough space, and it is better to
not save other les in the same folder as recording les.
Here you can congure and schedule the recording settings. After making any changes,
click the Save Settings button to save your changes.
64D-Link DCS-6010L User Manual
Section 4: Conguration
Size of each le for recording:
Time of each le for recording:
File Name Prex:
If this is selected, les will be separated based on the le
size you specify.
If this is selected, les will be separated based on the
maximum length you specify.
The prex name will be added on the le name of the
recording le(s).
65D-Link DCS-6010L User Manual
Section 4: Conguration
SD Card
Format SD Card:
View Recorded Picture:
Playback Recorded Video:
Refresh:
Click this icon to automatically format the SD card and
create "Picture" & "Video" folders.
If the picture les are stored on the SD card, click on the
picture folder and choose the picture le you would like
to view.
If video les are stored on the SD card, click on the video
folder and choose the video le you would like to view.
Reloads the le and folder information from the SD card.
Here you may browse and manage the recorded les which are stored on the SD card.
66D-Link DCS-6010L User Manual
Section 4: Conguration
Advanced
HTTPS
This page allows you to install and activate an HTTPS certicate for secure access to your camera. After making any changes, click the Save Settings
button to save your changes.
Enable HTTPS Secure Connection:
Create Certicate Method:
Status:
Note:
Enable the HTTPS service.
Choose the way the certicate should be created. Three
options are available:
Create a self-signed certicate automatically
Create a self-signed certicate manually
Create a certicate request and install
Displays the status of the certicate.
The certicate cannot be removed while the HTTPS is
still enabled. To remove the certicate, you must rst
uncheck Enable HTTPS secure connection.
67D-Link DCS-6010L User Manual
Section 4: Conguration
Access List
Here you can set access permissions for users to view your DCS-6010L.
Allow list:
Start IP address:
End IP address:
Delete allow list:
Deny list:
Delete deny list:
The list of IP addresses that have the access right to the
camera.
The starting IP Address of the devices (such as a computer)
that have permission to access the video of the camera.
Click Add to save the changes made.
Note: A total of seven lists can be congured for both
columns.
The ending IP Address of the devices (such as a computer)
that have permission to access the video of the camera.
Remove the customized setting from the Allow List.
The list of IP addresses that have no access rights to the
camera.
Remove the customized setting from the Delete List.
For example:
When the range of the Allowed List is set from 1.1.1.0
to 192.255.255.255 and the range of the Denied List is
set from 1.1.1.0 to 170.255.255.255. Only users with IPs
located between 171.0.0.0 and 192.255.255.255 can
access the Network Camera.
Alowed
List
Denied
List
68D-Link DCS-6010L User Manual
Section 4: Conguration
Maintenance
Device Management
You may modify the name and administrator’s password of your camera, as well as add and manage the user accounts for accessing the camera.
You may also use this section to create a unique name and congure the OSD settings for your camera.
Admin Password Setting:
Add User Account:
User Name:
Password:
User List:
Camera Name:
Enable OSD:
Label:
Show Time:
Set a new password for the administrator’s account.
Add new user account.
The user name for the new account.
The password for the new account.
All the existing user accounts will be displayed here. You
may delete accounts included in the list, but you may
want to reserve at least one as a guest account.
Create a unique name for your camera that will be added
to the le name prex when creating a snapshot or a
video clip.
Select this option to enable the On-Screen Display
feature for your camera.
Enter a label for the camera, which will be shown on the
OSD when it is enabled.
Select this option to enable the time-stamp display on
the video screen.
69D-Link DCS-6010L User Manual
Section 4: Conguration
System
In this section, you may backup, restore and reset the camera conguration, or reboot the camera.
Save To Local Hard Drive:
Local From Local Hard Drive:
Restore to Factory Default:
Reboot Device:
You may save your current camera conguration as a le
on your computer.
Locate a pre-saved conguration by clicking Browse and
then restore the pre-dened settings to your camera by
clicking Load Conguration.
You may reset your camera and restore the factory
settings by clicking Restore Factory Defaults.
This will restart your camera.
70D-Link DCS-6010L User Manual
Section 4: Conguration
Firmware Upgrade
The camera's current rmware version will be displayed on this screen. You may visit the D-Link Support Website to check for the latest available
rmware version.
To upgrade the rmware on your DCS-6010L, please download and save the latest rmware version from the D-Link Support Page to your local
hard drive. Locate the le on your local hard drive by clicking the Browse button. Select the le and click the Upload button to start upgrading the
rmware.
Current Firmware Version:
Current Product Name:
File Path:
Upload:
Displays the detected rmware version.
Displays the camera model name.
Locate the le (upgraded rmware) on your hard drive
by clicking Browse.
Uploads the new rmware to your camera.
71D-Link DCS-6010L User Manual
Section 4: Conguration
Status
Device Info
This page displays detailed information about your device and network connection.
72D-Link DCS-6010L User Manual
Section 4: Conguration
This page displays the log information of your camera. You may download the information by clicking Download. You may also click Clear to delete
the saved log information.
Logs
73D-Link DCS-6010L User Manual
Section 4: Conguration
This page provides helpful information regarding camera operation.
Help
74D-Link DCS-6010L User Manual
Appendix A: Technical Specications
Technical Specications
Camera Camera Hardware
Prole
1/3.5” 2 megapixel progressive CMOS sensor
Minimum illumination: 2.0 lux
Built-in microphone and speaker
10x digital zoom
Focal length: 1.25 mm
Aperture: F2.0
Angle of view:
(H) 180°
(V) 180°
(D) 180°
Image Features
Congurable image size, quality, frame rate, and bit rate
Fisheye distortion correction
Time stamp and text overlays
Congurable privacy mask zones
Congurable shutter speed, brightness, saturation, contrast,
and sharpness
Congurable motion detection windows
Video Compression
Simultaneous H.264/MPEG-4/MJPEG format compression
H.264/MPEG-4 multicast streaming
JPEG for still images
Video Resolution 1600 x 1200, 1200 x 900, 800 x 600, 400 x 300
Audio Support G.726, G.711
External Device
Interface
10/100 BASE-TX Fast Ethernet port
IEEE 802.11n 2.4GHz single band wireless
MicroSD/SDHC card slot
Network Network Protocols IPv6
IPv4
TCP/IP
UDP
ICMP
DHCP client
NTP client (D-Link)
DNS client
DDNS client (D-Link)
SMTP client
FTP client
HTTP / HTTPS
Samba Client
PPPoE
UPnP port forwarding
RTP / RTSP/ RTCP
IP ltering
QoS
CoS
Multicast
IGMP
ONVIF compliant
Security
Administrator and user group protection
Password authentication
HTTP and RTSP digest encryption
75D-Link DCS-6010L User Manual
Appendix A: Technical Specications
System
Management
System
Requirements for
Web Interface
Browser: Internet Explorer, Firefox, Chrome, Safari
Event Management
Motion detection
Event notication and uploading of snapshots/video clips via
e-mail or FTP
Supports multiple SMTP and FTP servers
Multiple event notications
Multiple recording methods for easy backup
Remote
Management
Take snapshots/video clips and save to local hard drive or NAS
via web browser
Conguration interface accessible via web browser
Mobile Support Windows 7/Vista/XP system, Pocket PC, or mobile phone mydlink mobile app for iOS and Android mobile devices
D-ViewCam™ System
Requirements
Operating System: Microsoft Windows 7/Vista/XP
Web Browser: Internet Explorer 7 or higher
Protocol: Standard TCP/IP
D-ViewCam™
Software Functions
Remote management/control of up to 32 cameras
Viewing of up to 32 cameras on one screen
Supports all management functions provided in web interface
Scheduled motion triggered, or manual recording options
General Weight 267 g +-5%
External Power
Adaptor Input: 100 to 240 V AC, 50/60 Hz Output: 5 V DC, 1.2 A
Power Consumption 3.9 watts max.
Temperature Operating: 0 to 40 °C (32 to 104 °F) Storage: -20 to 70 °C (-4 to 158 °F)
Humidity Operating: 20% to 80% non-condensing Storage: 5% to 95% non-condensing
Certications CE
CE LVD
FCC
C-Tick
76D-Link DCS-6010L User Manual
Appendix A: Technical Specications
Dimensions
•
77D-Link DCS-6010L User Manual
Appendix B: Safety Statements
CE Mark Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take
adequate measures.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Safety Statements
78D-Link DCS-6010L User Manual
Appendix B: Safety Statements
IMPORTANT NOTICE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
The availability of some specic channels and/or operational frequency bands are country dependent and are rmware programmed at the factory
to match the intended destination. The rmware setting is not accessible by the end user.
For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local D-Link
oce.
Industry Canada Notice:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.