D-Link DES-F1018P-E User Manual
Displayed below is the user manual for DES-F1018P-E by D-Link which is a product in the Network Switches category. This manual has pages.
PRODUCT QUICK INSTALLATION GUIDE
DES-F1018P-E
18-Port 250m Long Reach PoE Switch with
16 Fast Ethernet PoE+ Ports and
2 Gigabit Uplink Ports with 1 Combo SFP/RJ45 Port
1.1 Package Contents
The package contains the following items:
• PoE Switch
• Power Cord
• 19” Rack Mounting Kit
• Quick Installation Guide
1.2 Safety Instructions
Use the following safety guidelines to ensure your own personal safety and to
help protect your equipment from potential damage.
• The power cable should be disconnected from the mains during the installation
process;
• Wear a grounded anti-static wrist band to avoid the build-up of static electricity;
• Power the product only from the type of external power source indicated on the
electrical ratings label.
• Observe extension cable and power strip ratings. Make sure that the total ampere
rating of all products plugged into the extension cable or power strip does not exceed
80 percent of the ampere ratings limit for the extension cable or power strip;
To avoid the risk of electric shock, do not open the switch housing.
• Do not use damaged power cords. Do not modify power cables or plugs.
1.3 Connecting Power
Connect one end of the power cord to the rear of the switch, and the other end to
the mains power outlet.
1.4 Product Connection Diagram
FRONT PANEL
1.5 Product Installation
The DES-F1018P-E switch can be installed on a desktop, shelf or mounted in a
standard 19-inch rack.
To install the switch in a rack, attach the supplied mounting brackets to the side of the
switch and fasten the brackets to the sides of the switch using the screws from the
switch mounting kit.
Align the brackets and rack holes. Fasten each bracket to the rack.
1.6 Product Ports Description
Port
Description
PoE 1-16
PoE Port: Support IEEE802.3af/at standard Power over Ethernet,
used to connect PD devices;
Ports 1 – 8 PoE support cable lengths up to 250m @ 10Mbps
(“Extend” mode enabled);
Ports 9 – 16 PoE, support cable lengths up to 100m.
Uplink
Non-PoE port: used to connect NVR, PC, Aggregation Switch etc.
AC Power
Input
Connect power cord to the mains power outlet.
1.7 Product Specifications
Switch Modes
Extend: Supports long reach PoE delivery, up to 250m.
(Cat 5 or better cabling is recommended)
VLAN: Isolates ports from each other. Adds security and improves
network performance by constraining broadcast traffic.
QOS: Introduces application prioritisation. Traffic with higher priority
(e.g. Voice over IP) will be forwarded ahead of the queue.
PoE: Automatically restarts a remote device by disabling and re-enabling
PoE on the port if it detects the remote device has locked up (no
incoming traffic).
Network Ports
16 x 10/100Mbps PoE RJ45 ports (Port 1 – Port 16)
2 x Gigabit RJ45 Uplink ports with SFP (Combo) port
Transfer Rate
100Mbps full Duplex, 10 or 100Mbps Half Duplex (Downlink)
Network
Protocol
Standards
IEEE 802.3i, IEEE 802.3u, IEEE 802.3x, IEEE 802.3af, IEEE 802.3at
Performance
Bandwidth: 5.2Gbps (non-blocking)
Network delay (100 to 100Mbps):
maximum 20 μs (using 64 byte packet)
Frame filtering and transmission rate:
10M port maximum 14,800pps
100M port maximum 148,800pps
LED indicator
Power
RESV
LINK/ACT
PoE pins
1, 2 (+), 3, 6 (-)
Power
Max power for single port 30W
Total PoE budget: 150W
Dimensions
Size (L x W x H): 285mm x 180mm x 44mm
Weight: 2.3kg
Environmental
Operating Temperature: 0° - 40°C
Operating Humidity: 10% - 90%, Non-condensing
Safety
CE/ROHS/FCC