Table of Contents
- Preface
- Product Overview
- Installation
- Configuration
- Connect a Wireless Client to your Router
- Troubleshooting
- Wireless Basics
- Networking Basics
- Technical Specifications
D-Link DIR-809 User Manual
Displayed below is the user manual for DIR-809 by D-Link which is a product in the Wireless Routers category. This manual has pages.
Version 1.01 | 2015/9/7
Wireless AC750 Dual Band Router
User Manual
DIR-809
iD-Link DIR-809 User Manual
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any
person or organization of such revisions or changes.
Manual Revisions
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United
States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of
their respective companies.
Copyright © 2015 by D-Link Corporation, Inc.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission
from D-Link Corporation, Inc.
Revision Date Description
1.01 September 7, 2015 • Initial release for revision A3
Preface
iiD-Link DIR-809 User Manual
Table of Contents
Preface ................................................................................. i
Product Overview .............................................................. 1
Package Contents ......................................................................... 1
System Requirements ................................................................. 2
Introduction ................................................................................... 3
Features ............................................................................................ 4
Hardware Overview ..................................................................... 5
Connections ........................................................................... 5
LEDs ........................................................................................... 6
Installation ......................................................................... 7
Before you Begin ........................................................................... 7
Wireless Installation Considerations ......................................8
Manual Setup ................................................................................. 9
Conguration ...................................................................11
Easy Setup Wizard ......................................................................12
Internet Connection ..........................................................13
Wireless Connection ..........................................................13
Advanced Network Conguration .......................................15
Internet Connection Type (Manual Conguration) 17
Dynamic IP (DHCP) ........................................................18
Static (assigned by ISP) ................................................19
PPPoE (Username / Password) ..................................20
PPTP ....................................................................................22
L2TP ....................................................................................24
Wireless Settings .................................................................26
Wireless Router Mode ..................................................26
Access Point Mode ........................................................27
Repeater Mode ...............................................................28
Wireless Router Mode .......................................................29
2.4G Wireless Network Settings ................................29
5G Wireless Network Settings ...................................30
Wireless Security .................................................................31
What is WPA? ...................................................................31
2.4G/5G Wireless Security Mode ..............................32
AP Mode ................................................................................. 34
Repeater 2.4 GHz Mode .................................................... 35
Repeater 5 GHz Mode .......................................................37
Network Settings ................................................................39
Router Settings ...............................................................39
DHCP Server Settings ...................................................40
DHCP Reservation .........................................................41
Advanced ............................................................................... 42
Virtual Server ...................................................................42
Port Forwarding .............................................................43
Application Rules ...........................................................44
MAC Filter .........................................................................45
Website Filters .................................................................46
Trac Control ..................................................................47
Firewall Settings .............................................................48
2.4G Advanced Wireless ..............................................50
Table of Contents
iiiD-Link DIR-809 User Manual
Table of Contents
5G Advanced Wireless ..................................................51
Advanced Network Settings ......................................52
Wi-Fi Protected Setup .......................................................54
Wi-Fi Protected Setup Wizard ......................................... 55
Tools ........................................................................................57
Admin.................................................................................57
Time ....................................................................................58
System ...............................................................................59
Firmware ...........................................................................60
Language Pack ................................................................ 60
Dynamic DNS ..................................................................61
System Check ..................................................................62
Status ......................................................................................63
Device Info .......................................................................63
Logs.....................................................................................64
Statistics ............................................................................65
Internet Sessions ............................................................ 66
Wireless..............................................................................67
Support ..................................................................................68
Connect a Wireless Client to your Router ......................69
WPS Button ...................................................................................69
Windows® 8 ................................................................................... 70
WPA/WPA2 ............................................................................70
Windows® 7 ................................................................................... 72
WPA/WPA2 ............................................................................72
WPS ..........................................................................................75
Windows Vista® ............................................................................79
WPA/WPA2 ............................................................................80
WPS/WCN 2.0 .......................................................................82
Windows® XP ................................................................................ 83
WPA/WPA2 ............................................................................84
Troubleshooting ..............................................................86
Wireless Basics .................................................................90
What is Wireless? ......................................................................... 91
Tips ...................................................................................................93
Wireless Modes ............................................................................94
Networking Basics ...........................................................95
Check your IP address ...............................................................95
Statically Assign an IP address ...............................................96
Technical Specications ..................................................97
1D-Link DIR-809 User Manual
Section 1 - Product Overview
Product Overview
Package Contents
Note: Using a power supply with a dierent voltage rating than the one included with the DIR-809 will cause damage and void the warranty
for this product.
If any of the above items are missing, please contact your reseller.
DIR-809 Wireless AC750 Dual Band Router
Ethernet Cable
Power Adapter
Wi-Fi Conguration Note
CD-ROM
Wi-Fi Conguration Note
2D-Link DIR-809 User Manual
Section 1 - Product Overview
Network Requirements
• An Ethernet-based Cable or DSL modem
• IEEE 802.11ac, 802.11a, 802.11n or 802.11g wireless clients
• 10/100 Ethernet
Web-based Conguration
Utility Requirements
Computer with the following:
• Windows®, Apple® Mac OS®, or Linux-
based operating system
• An installed Ethernet adapter
Browser Requirements:
Microsoft Internet Explorer® 9, Mozilla® Firefox® 20.0,
Google® Chrome® 25.0, or Safari® 5.1 or higher version
Windows® Users: Make sure you have the latest version of Java
installed. Visit www.java.com to download the latest version.
System Requirements
3D-Link DIR-809 User Manual
Section 1 - Product Overview
Introduction
The D-Link DIR-809 is a IEEE 802.11ac compliant device that delivers up to three times faster speeds than 802.11n while staying
backward compatible with 802.11a/g/b devices. Connect the DIR-809 to a Cable or DSL modem and provide high-speed
Internet access to multiple computers, game consoles, and media players. Create a secure wireless network to share photos,
les, music, videos, printers, and network storage. Powered by the 802.11ac technology this router provides wireless coverage
for homes and oces, or for users running bandwidth-intensive applications.
With some routers, all wired and wireless trac, including VoIP, Video Streaming, Online Gaming, and Web browsing are mixed
together into a single data stream. By handling data this way, applications like video streaming could pause or delay. With
D-Link Intelligent QoS Technology, wired and wireless trac are analyzed and separated into multiple data streams.
The DIR-809 supports the latest wireless security features to help prevent unauthorized access, be it from over a wireless network
or the Internet. Support for WPA™ and WPA2™ standards ensure that you will be able to use the best possible encryption
regardless of your client devices. In addition, this router utilizes Dual Active Firewalls (SPI and NAT) to prevent potential attacks
from across the Internet so you and your family can browser the Internet with peace-of-mind.
4D-Link DIR-809 User Manual
Section 1 - Product Overview
• Ultimate Fast Wireless Networking - The DIR-809 provides up to 300 Mbps wireless bandwidth in the 2.4 GHz
band and up to 433 Mbps wireless bandwidth in the 5 GHz band with other 802.11ac and draft 802.11n wireless
clients. This capability allows users to participate in real-time activities online, such as video streaming, online
gaming, and real-time audio. The performance of this 802.11ac wireless router gives you the freedom of wireless
networking at speeds 3x faster than 802.11n.
• Compatible with 802.11a/g/n Devices - The DIR-809 is compatible with the IEEE 802.11a, 802.11g, and 802.11n
wireless standards, so it can connect with existing networking devices as well as PCI, USB, and CardBus network
adapters.
• Advanced Firewall Features - The Web-based user interface displays a number of advanced network
management features including:
• Content Filtering - Easily applied content ltering based on MAC address or URL.
• Secure Multiple/Concurrent Sessions - The DIR-809 can pass through VPN sessions. It supports
multiple and concurrent IPSec and PPTP sessions, so users behind the DIR-809 can securely access
corporate networks.
• User-friendly Easy Setup Wizard - Through its easy-to-use Web-based user interface, the DIR-809 lets you
quickly and easily congure your router, letting you surf the Internet within minutes.
* Maximum wireless signal rate derived from IEEE Standard 802.11a, 802.11g, 802.11n and draft 802.11ac specications. Actual data throughput will vary. Network conditions
and environmental factors, including volume of network trac, building materials and construction, and network overhead, lower actual data throughput rate. Environmental
conditions will adversely aect wireless signal range.
Features
5D-Link DIR-809 User Manual
Section 1 - Product Overview
Hardware Overview
Connections
1LAN Ports (1 - 4) Connect 10/100 Ethernet devices such as computers, switches, storage (NAS) devices
and game consoles.
2Internet Port Using an Ethernet cable, connect your broadband modem to this port.
3Power Connector Connector for the supplied power adapter.
4WPS & Reset
Button
Press and hold the button for 1-7 seconds to activate WPS-PBC Discovery Mode.
Press and hold the button for at least 8 seconds to reset the router to default settings.
4
12 3
6D-Link DIR-809 User Manual
Section 1 - Product Overview
Hardware Overview
LEDs
1 Power LED A solid green light indicates a proper connection to the power supply.
2 Internet LED A solid light indicates connection on the Internet port.
3 WPS LED This LED blinks during WPS handshake phase.
4 WLAN A solid light indicates that the wireless segment is ready.
5Local Network LEDs A solid light indicates a connection to an Ethernet-enabled computer on ports 1-4.
53
21 4
7D-Link DIR-809 User Manual
Section 2 - Installation
Before you Begin
Installation
This section will walk you through the installation process. Placement of the router is very important. Do not place the router
in an enclosed area such as a closet, cabinet, or in an attic or garage.
• Please congure the router with the computer that was last connected directly to your modem.
• You can only use the Ethernet port on your modem. If you were using the USB connection before using the router,
then you must turn o your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port
on the router, and then turn the modem back on. In some cases, you may need to call your ISP to change connection
types (USB to Ethernet).
• If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as WinPoet,
Broadjump, or Enternet 300 from your computer or you will not be able to connect to the Internet.
8D-Link DIR-809 User Manual
Section 2 - Installation
Wireless Installation Considerations
The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the
operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings,
or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types
of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to
follow these basic guidelines:
1. Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum -
each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that
the number of walls or ceilings is minimized.
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle
appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position
devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception.
3. Building Materials make a dierence. A solid metal door or aluminum studs may have a negative eect on range.
Try to position access points, wireless routers, and computers so that the signal passes through drywall or open
doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (sh tanks), mirrors, le
cabinets, brick, and concrete will degrade your wireless signal.
4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF
noise.
5. If you are using 2.4 GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security
systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4 GHz phone
base is as far away from your wireless devices as possible. The base transmits a signal even if the phone in not
in use.
9D-Link DIR-809 User Manual
Section 2 - Installation
1. Turn o and unplug your cable or DSL broadband modem. This is required.
Manual Setup
2. Position your router close to your modem and a computer. Place the router in an open area of your intended
work area for better wireless coverage.
3. Unplug the Ethernet cable from your modem (or existing router if upgrading) that is connected to your computer.
Plug it into the LAN port labeled 1 on the back of your router. The router is now connected to your computer.
Modem
DIR-809
Computer
10D-Link DIR-809 User Manual
Section 2 - Installation
INTERNET
4. Plug one end of the included blue Ethernet cable that came with your router into the yellow port labeled
INTERNET on the back of the router. Plug the other end of this cable into the Ethernet port on your modem.
5. Reconnect the power adapter to your cable or DSL broadband modem and wait for two minutes.
6. Connect the supplied power adapter into the power port on the back of the router and then plug it into a power
outlet or surge protector. The power LED will light up. Allow 1 minute for the router to boot up.
7. If you are connecting to a Broadband service that uses a dynamic connection (not PPPoE), you may be online
already. Try opening a web browser and enter a web site address.
INTERNET
DIR-809
DIR-809
Modem
Modem
Computer
Computer
11D-Link DIR-809 User Manual
Section 3 - Conguration
There are several dierent ways you can congure your router to connect to the Internet and connect to your clients:
• D-Link Easy Setup Wizard - This wizard will launch when you log into the router for the rst time. Refer to page 12.
• Manual Setup - Log into the router and manually congure your router (advanced users only). Refer to page 15.
Conguration
12D-Link DIR-809 User Manual
Section 3 - Conguration
The Easy Setup Wizard consists of two parts: Internet Connection and Wireless
Connection.
Easy Setup Wizard
If this is your rst time using the router, open your web browser. You will
automatically be directed to the Wizard Setup Screen. If not, type http://
dlinkrouter.local./ or 192.168.0.1 into the address bar and press Enter. The
username, “admin” will already be lled in. Leave the password blank and
press the login button.
If you would like to manually set up the router, please refer to the Web-Based
Conguration Utility section on page 15.
13D-Link DIR-809 User Manual
Section 3 - Conguration
PPPoE
Enter your username and user password details provided by your Internet
Service Provider. This option is typically used for DSL Internet service.
Note: Make sure to remove your PPPoE software from your computer. The software
is no longer needed and will not work through a router.
First select the INTERNET connection type. The options are Static IP, Dynamic IP (DHCP), and PPPoE(Username / Password).
Internet Connection
Static IP
Enter the IP and DNS settings supplied by your ISP.
Dynamic IP (DHCP)
The router will attempt to automatically congure itself for Dynamic IP Internet
Connections.
Next, create a Wi-Fi network name (SSID) for both the 2.4 GHz and 5 GHz
segments using up to 32 characters.
Create a Wi-Fi password (between 8-63 characters). Your wireless clients will
need to have this passphrase or key in order to connect to your wireless network.
Click Connect to continue.
Wireless Connection
14D-Link DIR-809 User Manual
Section 3 - Conguration
Please wait while your router detects your Internet connection type. If you
selected PPPoE as your Internet connection, you may need to enter information
provided by you ISP, such as username and password.
Congratulations, your router setup is complete. Upon clicking Complete you
will be redirected to the www.dlink.com may now freely use the Internet.
If the router does not detect a valid Ethernet connection from the Internet
port, this screen will appear. Verify your broadband modem is connected to
the Internet port and then click Try Again.
15D-Link DIR-809 User Manual
Section 3 - Conguration
Advanced Network Conguration
Upon login, bypass the Easy Setup by clicking Advanced Network in the
bottom right hand corner of the page.
If this is your rst time using the router, open your web browser. You will
automatically be directed to the Wizard Setup Screen. If not, type http://
dlinkrouter.local./ or 192.168.0.1 into the address bar and press Enter. The
username, “admin” will already be lled in. Leave the password blank and
press the login button.
16D-Link DIR-809 User Manual
Section 3 - Conguration
Upon clicking the “Advanced Network” option, you will be brought to the
Setup - Internet page. From this page you can congure your connection and
router settings manually.
If you want to congure your router to connect to the Internet using the wizard,
click Easy Setup. You will be directed back to the Easy Setup Wizard. Refer to
the previous section.
17D-Link DIR-809 User Manual
Section 3 - Conguration
At any given point the user can save the conguration by clicking on the
Save Settings button. If you choose to discard the changes made, click on
the Don’t Save Settings button.
Internet Connection Type (Manual Conguration)
Internet Connection Type
In this section, the user can select from a list of Internet Connection types
that can be congured and used on this router. Options to choose from are
Static IP, Dynamic IP, PPPoE, PPTP, and L2TP.
After selecting a specic Internet Connection type, this page will automati-
cally refresh and provide unique elds to congure related to the specied
Internet Connection type.
18D-Link DIR-809 User Manual
Section 3 - Conguration
My Internet Connection is: Dynamic IP (DHCP)
This option allows the router to obtain an IP address automatically from the WAN device that is connected to the Internet
port.
Note: If you’re not sure about the type of Internet Connection you have, please contact your Internet Service Provider (ISP)
for assistance.
After selecting Dynamic IP, the following parameters will be available for conguration:
Host Name: The Host Name is optional but may be required by some ISPs. Leave blank
if you are not sure.
MAC
Address:
The default MAC Address is set to the Internet port’s physical interface
MAC address on the Broadband Router. It is not recommended that you
change the default MAC address unless required by your ISP. You can use
the Clone Your PC’s MAC Address button to replace the Internet port’s
MAC address with the MAC address of your Ethernet card.
Primary DNS: Enter the Primary DNS IP address used here.
Secondary
DNS:
Enter the Secondary DNS IP address used here. This eld is normally
optional. Only one DNS address is required for a functional Internet
connection, but using a second DNS address provides more stability.
MTU: Maximum Transmission Unit - you may need to change the MTU for opti-
mal performance with your specic ISP. 1500 is the default MTU.
Dynamic IP (DHCP)
19D-Link DIR-809 User Manual
Section 3 - Conguration
Static (assigned by ISP)
My Internet Connection is: Static IP
Select Static IP Address if all the Internet port’s IP information is provided to you by your ISP. You will need to enter in the IP
address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the elds
must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Router will not accept the IP address
if it is not in this format.
My Internet
Connnection
Select Static IP to manually enter the IP settings supplied by your ISP.
IP Address: Enter the Static IP address provided by the ISP here.
Subnet Mask: Enter the Subnet Mask provided by the ISP here.
Default
Gateway:
Enter the Gateway IP address provided by the ISP here.
MAC Address: The default MAC Address is set to the Internet port’s physical interface MAC
address on the Broadband Router. It is not recommended that you change
the default MAC address unless required by your ISP. You can use the Copy
Your PC’s MAC Address button to replace the Internet port’s MAC address
with the MAC address of your Ethernet card.
Primary
DNS Address:
Enter the Primary DNS IP address used here.
Secondary
DNS Address:
Enter the Secondary DNS IP address used here. This eld is normally op-
tional. Only one DNS address is required for a functional Internet connec-
tion, but using a second DNS address provides more stability.
MTU: Maximum Transmission Unit - you may need to change the MTU for optimal
performance with your specic ISP. 1500 is the default MTU.
20D-Link DIR-809 User Manual
Section 3 - Conguration
PPPoE (Username / Password)
Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a
username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your
computer. The software is no longer needed and will not work through a router.
My Internet
Connection:
Select PPPoE (Username/Password) from the drop-down menu.
Address
Mode:
Here the user can specify whether this Internet connection requires the
use of a Dynamic or Static IP address. PPPoE usually requires a Dynamic
IP conguration.
Username: Enter the PPPoE account user name used here. This information is given
by the ISP.
Password: Enter the PPPoE account password used here. This information is given by
the ISP.
Conrm
Password:
Re-enter the PPPoE account password used here.
Service
Name:
This optional eld enables the user to enter a service name to identify this
Internet connection here.
IP Address: Enter the PPPoE IP address used here. This option is only available if Static
IP is selected.
MAC
Address:
The default MAC Address is set to the Internet port’s physical interface
MAC address on the Broadband Router. It is not recommended that you
change the default MAC address unless required by your ISP. You can use
the Copy Your PC’s MAC Address button to replace the Internet port’s
MAC address with the MAC address of your Ethernet card.
21D-Link DIR-809 User Manual
Section 3 - Conguration
DNS Mode: This option allow the router to obtain the DNS IP addresses from the ISP,
when Receive DNS from ISP is selected, or allows the user to enter DNS
IP address manually, when Enter DNS Manually is selected.
Primary DNS
Server:
Enter the Primary DNS IP address used here.
Secondary
DNS Server:
Enter the Secondary DNS IP address used here. This eld is normally op-
tional. Only one DNS address is required for a functional Internet connec-
tion, but using a second DNS address provides more stability.
Maximum
Idle Time:
Enter a maximum idle time during which the Internet connection is main-
tained during inactivity.
MTU: Maximum Transmission Unit - you may need to change the MTU for opti-
mal performance with your specic ISP. 1492 is the default MTU.
Connection
Mode Select
Use the radio buttons to specify the reconnect mode. The user can select
Always On, Manual, or Connection-on Demand.
22D-Link DIR-809 User Manual
Section 3 - Conguration
PPTP
Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with a username
and password. This option is typically used for DSL services.
My Internet
Connection:
Select PPTP (Username/Password) from the drop-down menu.
Address
Mode:
Select Dynamic (most common) or Static. Select Static if your ISP as-
signed you the IP address, subnet mask, gateway, and DNS server ad-
dresses.
PPTP IP
Address:
Enter the IP address (Static PPTP only).
PPTP Subnet
Mask:
Enter the primary and secondary DNS server addresses (Static PPTP only).
PPTP
Gateway IP
Address:
Enter the gateway IP address provided by your ISP (Static only).
Primary DNS
Server:
The DNS server information will be supplied by your ISP (Internet Service
Provider.)
MAC
Address:
The default MAC address is set to the WAN’s physical interface MAC ad-
dress on the broadband router. It is not recommended that you change
the default MAC address unless required by your ISP.
You can use the Copy Your PC’s MAC Address button to copy the MAC
address of the Ethernet card installed by your ISP and replace the WAN
MAC address with the MAC address of the router. It is not recommended
that you change the default MAC address unless required by your ISP.
PPTP Server
IP Address:
Enter the server IP address provided by your ISP (optional).
23D-Link DIR-809 User Manual
Section 3 - Conguration
User Name: Enter your PPTP account name.
Password: Enter your PPTP password, then retype the password in the next box.
Maximum
Idle Time:
Enter a maximum idle time during which the Internet connection is main-
tained during inactivity.
MTU: Maximum Transmission Unit - You may need to change the MTU for opti-
mal performance.
Connect
Mode:
Select either Always-on, Manual, or Connect-on demand.
24D-Link DIR-809 User Manual
Section 3 - Conguration
L2TP
My Internet
Connection:
Select L2TP (Username/Password) from the drop-down menu.
Address
Mode:
Here the user can specify whether this Internet connection requires the
use of a dynamic or static IP address. L2TP usually requires a
dynamic IP conguration.
L2TP IP
Address:
Enter the L2TP IP address used here. This
option is only available if Static IP is selected.
L2TP
Subnet
Mask:
Enter the L2TP subnet mask used here.
L2TP
Gateway IP
Address:
Enter the L2TP gateway IP address used here.
Primary
DNS
Address:
Enter the primary DNS IP address used here.
MAC
Address:
The default MAC address is set to the WAN’s physical interface MAC ad-
dress on the broadband router. It is not recommended that you change
the default MAC address unless required by your ISP.
You can use the Copy Your PC’s MAC Address button to copy the MAC
address of the Ethernet card installed by your ISP and replace the WAN
MAC address with the MAC address of the router. It is not recommended
that you change the default MAC address unless required by your ISP.
Choose L2TP (Point-to-Point-Tunneling Protocol ) if your ISP uses a L2TP connection. Your ISP will provide you with a username
and password.
25D-Link DIR-809 User Manual
Section 3 - Conguration
L2TP Server
IP Address:
Enter the L2TP server IP address used here. This is normally the same as
the L2TP gateway IP address.
User Name: Enter the L2TP username used here.
Password: Enter your L2TP password, then retype the password in the next box.
Maximum
Idle Time:
Enter a maximum idle time during which the Internet connection is main-
tained during inactivity. To disable this feature, enable Auto-reconnect.
MTU: Maximum Transmission Unit - You may need to change the MTU for opti-
mal performance with your specic ISP.
Connect
Mode
Select:
Select either Always-on, Manual, or Connect-on demand.
26D-Link DIR-809 User Manual
Section 3 - Conguration
Wireless Settings
Wireless Router Mode
Router Repeater Mode Wi-Fi Hotspot Mode
Cable/DSL Modem Wireless DevicesInternet
In Wireless Router Mode, the DIR-809 connects to your cable modem, DSL modem, or other Internet source and shares
your Internet connection with your devices wirelessly, providing Internet access for an entire home or oce. See “Wireless
Router Mode” on page 29 for conguration options.
Wireless Mode: The DIR-809 may be used as a Wireless Router, Access Point,
or a Repeater on either the 2.4 GHz or 5 Ghz bands.
27D-Link DIR-809 User Manual
Section 3 - Conguration
Access Point Mode
Router
(optional)
Wireless Devices
Internet
(optional)
In Access Point Mode, the DIR-809 connects your wireless devices together, but does not provide routing functionality. It
also allows a connected wired device to connect to your other devices wirelessly. This can be useful if you already have an
existing Internet router that does not have built-in wireless capabilities. You can also use this to create a private wireless
network without Internet access so that your devices can securely connect to one another without being exposed to the
Internet or other computers. See “AP Mode” on page 34 for conguration options.
Access Point Mode
28D-Link DIR-809 User Manual
Section 3 - Conguration
Router Repeater Mode Wi-Fi Hotspot Mode
Internet Wireless Router Wireless Devices
Wired device
(optional)
In Repeater Mode (2.4 GHz/5 GHz), the DIR-809 extends the range of an existing wireless network. You can use this to ex-
tend the coverage of an existing wireless router to provide better signal for parts of your home or oce that may have poor
reception. Additionally, you can use this mode to connect a wired device to a wireless network, which can be useful for de-
vices that do not have a built-in wireless card, such as some smart TVs, game consoles, or DVRs. When using repeater mode,
the SSID and settings of the repeated network will be duplicated by the DIR-809. The other unused wireless frequency will
be available to create a second wireless network with a dierent SSID. See “Repeater 2.4 GHz Mode” on page 35 and “Repeater
5 GHz Mode” on page 37 for conguration options.
Repeater Mode
29D-Link DIR-809 User Manual
Section 3 - Conguration
Enable
Wireless
Select or deslect this checkbox in order to enable or disable the 2.4 GHz
wireless radio.
Wireless
Network
Name:
The Service Set Identier (SSID) is the name of your wireless network. Cre-
ate a name using up to 32 characters. The SSID is case-sensitive. Enable
Auto Channel
Enable Auto
Channel
Scan:
The auto channel selection setting can be selected to allow this device to
choose the channel with the least amount of interference.
Wireless
Channel:
By default the channel is set to 1. The Channel can be changed to t the
channel setting for an existing wireless network or to customize the wire-
less network. If you enable Auto Channel Selection, this option will be
greyed out.
Transmission
Rate:
Select the transmit rate. It is strongly suggested to select Best (Automatic)
for best performance.
WMM WMM is QoS for your wireless network. This will improve the quality of
video and voice applications for your wireless clients.
Enable
Hidden
Wireless
The Hidden Wireless option allows you to hide your wireless network.
When this option is set to Visible, your wireless network name is broad-
casted to anyone within the range of your signal. If you are not using en-
cryption then they could connect to your network. When Invisible mode
is enabled, you must enter the Wireless Network Name (SSID) on the client
manually to connect to the network.
Wireless Router Mode
2.4G Wireless Network Settings
30D-Link DIR-809 User Manual
Section 3 - Conguration
Enable
Wireless
Select or deslect this checkbox in order to enable or disable the 2.4 GHz
wireless radio.
Wireless
Network
Name:
The Service Set Identier (SSID) is the name of your wireless network. Cre-
ate a name using up to 32 characters. The SSID is case-sensitive. Enable
Auto Channel
Enable Auto
Channel
Scan:
The auto channel selection setting can be selected to allow this device to
choose the channel with the least amount of interference.
Wireless
Channel:
By default the channel is set to 1. The Channel can be changed to t the
channel setting for an existing wireless network or to customize the wire-
less network. If you enable Auto Channel Selection, this option will be
greyed out.
Transmission
Rate:
Select the transmit rate. It is strongly suggested to select Best (Automatic)
for best performance.
WMM WMM is QoS for your wireless network. This will improve the quality of
video and voice applications for your wireless clients.
Enable
Hidden
Wireless
The Hidden Wireless option allows you to hide your wireless network.
When this option is set to Visible, your wireless network name is broad-
casted to anyone within the range of your signal. If you are not using en-
cryption then they could connect to your network. When Invisible mode
is enabled, you must enter the Wireless Network Name (SSID) on the client
manually to connect to the network.
5G Wireless Network Settings
31D-Link DIR-809 User Manual
Section 3 - Conguration
Wireless Security
This section will show you the dierent levels of security you can use to protect your data from intruders. The DIR-809 oers the following
types of security:
• WPA2 (Wi-Fi Protected Access 2) • WPA2-PSK (Pre-Shared Key)
• WPA (Wi-Fi Protected Access) • WPA-PSK (Pre-Shared Key)
What is WPA?
WPA (Wi-Fi Protected Access), is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy).
The 2 major improvements over WEP:
• Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing
algorithm and, by adding an integrity-checking feature, ensures that the keys haven’t been tampered with. WPA2 is
based on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP.
• User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP). WEP
regulates access to a wireless network based on a computer’s hardware-specic MAC address, which is relatively simple
to be snied out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized
network users can access the network.
WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between
8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key entered on your
wireless router or access point.
WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more secure public
key encryption system to ensure that only authorized network users can access the network.
32D-Link DIR-809 User Manual
Section 3 - Conguration
By default the wireless security of this router will be disabled. In this next options you can enable or disable wireless security for the 2.4 and 5
GHz frequency bands. There are ve settings available: Disable Wireless Security, WEP Wireless Security, WPA Only Wireless Security, WPA2
Only Wireless Security, and WPA/WPA2 Wireless Security. Each wireless band may be congured independently.
Wireless Security Mode: WEP
Wired Equivalent Privacy (WEP) is the most basic form of encryption that can be used for
wireless networks. Even though it is known as a ‘weak’ security method, it is better than
no security at all. Because some older wireless adapters only support WEP encryption,
this encryption method is still supported.
The following parameters will be available for conguration:
WEP Key
Length:
Here the user can specify to either use a 64 Bit or a 128 Bit encrypted key.
Authentication: Authentication is a process by which the router veries the identity of a
network device that is attempting to join the wireless network. There are
two types authentication for this device when using WEP. Open System
allows all wireless devices to communicate with the router before they
are required to provide the encryption key needed to gain access to the
network. Shared Key requires any wireless device attempting to commu-
nicate with the router to provide the encryption key needed to access the
network before they are allowed to communicate with the router.
WEP Key 1: Enter the WEP key used here. For 64-bit keys you must enter 10 hex digits
into each key box. For 128-bit keys you must enter 26 hex digits into each
key box. A hex digit is either a number from 0 to 9 or a letter from A to F.
You may also enter any text string into a WEP key box, in which case it will
be converted into a hexadecimal key using the ASCII values of the charac-
ters. A maximum of 5 text characters can be entered for 64-bit keys, and a
maximum of 13 characters for 128-bit keys.
2.4G/5G Wireless Security Mode
33D-Link DIR-809 User Manual
Section 3 - Conguration
Wireless Security Mode: WPA Wireless Security
Wi-Fi Protected Access (WPA) is a more advanced and secure wireless encryption method
than WEP. The options are WPA Only Wireless Security, WPA2 Only Wireless Security,
and WPA/WPA2 Wireless Security.
The following parameters will be available for conguration:
Cipher Type: Select the appropriate cipher type to use here. Options to choose from
are Temporal Key Integrity Protocol (TKIP), Advanced Encryption Standard
(AES), and Both (TKIP and AES).
Network Key: Enter the password you wish to use for the wireless network here. Wireless
clients wishing to join this network must supply this password in order to
join the network.
34D-Link DIR-809 User Manual
Section 3 - Conguration
AP Mode
Upon pressing the Save Settings button, the following reboot conrmation warning will
be shown.
To switch to AP Mode, select it from the drop down box, congure the desired wireless
network settings and press the Save Settings button at the top of the page.
After clicking Reboot Now the following screen will appear indicating that the device
may be congured from the 192.168.0.50 IP address.
Note: While in AP Mode, the DIR-809’s DHCP server is disabled and many conguration
options will be unavailable.
35D-Link DIR-809 User Manual
Section 3 - Conguration
Repeater 2.4 GHz Mode
To repeat a 2.4 GHz network, select Repeater 2.4 GHz Mode, from the drop down box.
From Site Survey, press the Scan button to nd networks available for repeating.
Once a Site Survey is complete, a list of potential candidates will be listed indicating the
type of networking device available, the channel it operates on, its signal strength, the
type of wireless security in use, and its SSID.
Select the radio button on the left side of the table of the wireless network you wish to
repeat.
If the selected wireless network has security enabled, supply the Network Key in box
provided.
36D-Link DIR-809 User Manual
Section 3 - Conguration
The following reboot conrmation warning will be shown.
Press the Save Settings button at the top of the page once you are satised with the
repeater settings,
Note: When the router is in repeater mode, the Enable Hidden Wireless option will be
disabled. WMM will automatically be enabled.
After clicking Reboot Now the following screen will appear indicating that the device
may be congured from the 192.168.0.50 IP address.
37D-Link DIR-809 User Manual
Section 3 - Conguration
Repeater 5 GHz Mode
From Site Survey, press the Scan button to nd networks available for repeating.
Once a Site Survey is complete, a list of potential candidates will be listed indicating the
type of networking device available, the channel it operates on, its signal strength, the
type of wireless security in use, and its SSID.
Select the radio button on the left side of the table of the wireless network you wish to
repeat.
If the selected wireless network has security enabled, supply the Network Key in the box
provided.
To repeat a 5 GHz network, select Repeater 5 GHz Mode, from the drop down box.
Note: When the router is in repeater mode, the Enable Hidden Wireless option will be
disabled. WMM will automatically be enabled.
38D-Link DIR-809 User Manual
Section 3 - Conguration
The following reboot conrmation warning will be shown.
Press the Save Settings button at the top of the page once you are satised with the
repeater settings,
Note: When the router is in repeater mode, the Enable Hidden Wireless option will be
disabled. WMM will automatically be enabled.
After clicking Reboot Now the following screen will appear indicating that the device
may be congured from the 192.168.0.50 IP address.
39D-Link DIR-809 User Manual
Section 3 - Conguration
This section will allow you to change the local network settings of the router and to congure the DHCP settings.
Network Settings
Router Settings
Router IP
Address:
Enter the IP address of the router. The default IP address is 192.168.0.1.
Subnet Mask: If you change the IP address, once you click Save Settings, you will need to
enter the new IP address in your browser to get back into the conguration
utility.
Enter the Subnet Mask. The default subnet mask is 255.255.255.0.
Local Domain: Enter the Domain name (Optional).
Enable DNS
Relay:
Uncheck the box to transfer the DNS server information from your ISP to your
computers. If checked, your computers will use the router for a DNS server.
40D-Link DIR-809 User Manual
Section 3 - Conguration
DHCP Server Settings
DHCP stands for Dynamic Host Control Protocol. The DIR-809 has a built-in DHCP server. The DHCP Server will automatically
assign an IP address to the computers on the LAN/private network. Be sure to set your computers to be DHCP clients by setting
their TCP/IP settings to “Obtain an IP Address Automatically.” When you turn your computers on, they will automatically load
the proper TCP/IP settings provided by the DIR-809. The DHCP Server will automatically allocate an unused IP address from
the IP address pool to the requesting computer. You must specify the starting and ending address of the IP address pool.
Enable DHCP
Server:
Check this box to enable the DHCP server on your router. Uncheck to disable
this function.
DHCP IP
Address
Range:
Enter the starting and ending IP addresses for the DHCP server’s IP
assignment.
Note: If you statically (manually) assign IP addresses to your computers or
devices, make sure the IP addresses are outside of this range or you may have
an IP conict.
DHCP Lease
Time:
The length of time for the IP address lease. Enter the Lease time in minutes.
DHCP Client
List:
This displays a list of devices which have received an IP
address from the DHCP server. The Host Name, IP Address,
MAC Address, and Expiration time is listed.
41D-Link DIR-809 User Manual
Section 3 - Conguration
DHCP Reservation
If you want a computer or device to always have the same IP address assigned, you can create a DHCP reservation. The router will assign the IP
address only to that computer or device.
Note: This IP address must be within the DHCP IP Address Range.
Computer
Name:
Enter the computer name or select from the drop-down menu and click <<.
IP Address: Enter the IP address you want to assign to the computer or device. This IP
Address must be within the DHCP IP Address Range.
MAC
Address:
Enter the MAC address of the computer or device.
Computer
Name:
If you want to assign an IP address to the computer you are currently on,
click this button to populate the elds.
Save: Click Save to save your entry. You must click Save Settings at the top to
activate your reservations.
DHCP Client Reserved List
DHCP
Reservations
List:
Displays any reservation entries. Displays the host name (name of your
computer or device), MAC Address, and IP address.
42D-Link DIR-809 User Manual
Section 3 - Conguration
This will allow you to open a single port. If you would like to open a range of
ports, refer to the next page.
Virtual Server
Advanced
Name: Enter a name for the rule or select an application from the drop-down menu.
Select an application and click << to populate the elds.
IP Address: Enter the IP address of the computer on your local network that you want
to allow the incoming service to. If your computer is receiving an IP address
automatically from the router (DHCP), you computer will be listed in the
“Computer Name” drop-down menu. Select your computer and click <<.
Private Port/
Public Port:
Enter the port that you want to open next to Private Port and Public Port.
The private and public ports are usually the same. The public port is the port
seen from the Internet side, and the private port is the port being used by
the application on the computer within your local network.
Protocol
Type:
Select TCP, UDP, or Any from the drop-down menu.
43D-Link DIR-809 User Manual
Section 3 - Conguration
This will allow you to open a single port or a range of ports.
Port Forwarding
Name: Enter a name for the rule or select an application from the drop-down menu.
Select an application and click << to populate the elds.
IP Address: Enter the IP address of the computer on your local network that you want
to allow the incoming service to. If your computer is receiving an IP address
automatically from the router (DHCP), you computer will be listed in the
“Computer Name” drop-down menu. Select your computer and click <<.
TCP/UDP: Enter the TCP and/or UDP port or ports that you want to open. You can enter
a single port or a range of ports. Separate ports with a common.
Example: 24,1009,3000-4000
44D-Link DIR-809 User Manual
Section 3 - Conguration
Application Rules
Some applications require multiple connections, such as Internet gaming, video conferencing, Internet telephony and others.
These applications have diculties working through NAT (Network Address Translation). Special Applications makes some of
these applications work with the DIR-809. If you need to run applications that require multiple connections, specify the port
normally associated with an application in the “Trigger Port” eld, select the protocol type as TCP or UDP, then enter the rewall
(public) ports associated with the trigger port to open them for inbound trac.
The DIR-809 provides some predened applications in the table on the bottom of the web page. Select the application you
want to use and enable it.
Name: Enter a name for the rule. You may select a
pre-dened application from the drop-down menu and click <<.
Trigger: This is the port used to trigger the application. It can
be either a single port or a range of ports.
Trac Type: Select the protocol of the trigger port (TCP, UDP, or Both).
Firewall: This is the port number on the Internet side that will be used to
access the application. You may dene a single port or a range of
ports. You can use a comma to add multiple ports or port ranges.
Trac Type: Select the protocol of the rewall port (TCP, UDP, or Both).
45D-Link DIR-809 User Manual
Section 3 - Conguration
MAC Filter
Use MAC (Media Access Control) Filters to allow or deny LAN (Local Area Network) computers by their MAC addresses from
accessing the network. You can either manually add a MAC address or select the MAC address from the list of clients that are
currently connected to the Broadband Router.
Congure
MAC
Filtering:
Select Turn MAC Filtering O, Allow MAC addresses listed below, or Deny
MAC addresses listed below from the drop-down menu.
MAC
Address:
Enter the MAC address you would like to lter.
To nd the MAC address on a computer, please refer to the Networking Basics
section in this manual.
DHCP Client: Select a DHCP client from the drop-down menu and click << to copy that
MAC Address.
46D-Link DIR-809 User Manual
Section 3 - Conguration
Website Filters
Website Filters are used to allow you to set up a list of Web sites that can be viewed by multiple users through the network.
To use this feature select to Allow or Deny, enter the domain or website and click Save Settings. You must also select Apply
Web Filter under the Access Control section.
Add Website
Filtering
Rule:
Select either DENY computers access to ONLY these sites or ALLOW
computers access to ONLY these sites.
Website URL Enter the URLs that you want to allow or block. Click Save Settings.
47D-Link DIR-809 User Manual
Section 3 - Conguration
Trac Control
Enable Trac
Control:
Select this function to control the access bandwidth of computers in LAN.
Automatic
Distribute
Bandwidth:
All of the computers in LAN will have their bandwidth distributed equally.
Key in
Download
Bandwidth
Manually:
Key in the value in kbps to setup the bandwidth manually.
Key in
Upload
Bandwidth
Manually:
Key in the value in kbps to setup the upload bandwidth manually.
Trac
Control
Rules:
When the option Automatic Distribute Bandwidth is unchecked,
you can select Guarantee minimum bandwidth, Restrict
maximum download bandwidth, or Restrict maximum upload
bandwidth of specic IP addresses from their drop-down boxes.
Schedule: The schedule of time when the lter will be enabled. The schedule
may be set to Always, which will allow the particular service to
always be enabled. You can create your own times by clicking New
Scheduler as well as in the Maintenance > Schedules section.
Trac Control can guarantee bandwidth priority to specied LAN/Wireless clients. You can do this by setting up trac control
rules. Click Save Settings to apply your settings.
48D-Link DIR-809 User Manual
Section 3 - Conguration
Firewall Settings
A rewall protects your network from the outside world. The DIR-809 oers a rewall type functionality. The SPI feature helps
prevent cyber attacks. Sometimes you may want a computer exposed to the outside world for certain types of applications.
If you choose to expose a computer, you can enable DMZ. DMZ is short for Demilitarized Zone. This option will expose the
chosen computer completely to the outside world.
Enable SPI: SPI (Stateful Packet Inspection, also known as dynamic packet ltering) helps
to prevent cyber attacks by tracking more state per session. It validates that
the trac passing through the session conforms to the protocol.
DMZ IP
Address:
Specify the IP address of the computer on the LAN that you want to have
unrestricted Internet communication. If this computer obtains it’s IP address
automatically using DHCP, be sure to make a static reservation on the Setup
> Network Settings page so that the IP address of the DMZ machine does
not change.
RTSP: Allows application that uses Real Time Streaming Protocol to receive
streaming media from the Internet. QuickTime and Real Player are some of
the common applications using this protocol.
49D-Link DIR-809 User Manual
Section 3 - Conguration
Firewall
Rules:
A total of 24 re wall rules may be created which dictate how specic trac
should be allowed or denied to pass through the rewall.
Name: Enter a descriptive name for the rewall rule.
Source
Interface:
Select the source interface, either WAN or LAN trac.
Source IP
Address
Input the source IP address, or IP address range to apply the rule to.
Destination
Interface:
Select the destination interface, either WAN or LAN.
Destination
IP Address
Input the IP address, or IP address range to apply the rule to.
Action: Select to Allow or Deny transport of the data packets according to the
criteria dened in the rule.
Protocol: Select the transport protocol that will be used for
the lter rule: TCP, UDP, ICMP, or ALL.
Port Range: Enter the desired port range for the lter rule.
50D-Link DIR-809 User Manual
Section 3 - Conguration
2.4G Advanced Wireless
Transmit
Power:
Set the transmit power of the antennas.
Wireless
Mode
Select the preferred frequency band to use for this wireless network. 802.11n
only, 802.11Mixed(g/b), 802.11, 802.11Mixed(n/g/b).
Band Width Select 20 MHz or 20/40 MHz (Auto). Select Select 20/40 MHz (Auto),if you
are using both 802.11n and non-802.11n wireless devices. Select Select 20
MHz, if you are not using any 802.11n wireless clients.
HT20/40
Coexistence:
Enable this option to reduce interference from other wireless networks in
your area. If the channel width is operating at 40 MHz and there is another
wireless network’s channel over-lapping and causing interference, the router
will automatically change to 20 MHz.
51D-Link DIR-809 User Manual
Section 3 - Conguration
5G Advanced Wireless
Transmit
Power:
Set the transmit power of the antennas.
Wireless
Mode
Select the preferred frequency band to use for this wireless network. The
options are 5G A, 5G N, 5G A+N, 5G AC, 5G N+AC, 5G A+N+AC.
Band Width Select 20 MHz, 20/40 MHz (Auto), or 20/40/80 MHz (Auto).
52D-Link DIR-809 User Manual
Section 3 - Conguration
Advanced Network Settings
Enable UPnP: To use the Universal Plug and Play (UPnP™) feature click on Enabled.
UPnP provides compatibility with networking equipment, software and
peripherals.
WAN Ping: Checking the box will allow the DIR-809 to respond to pings. Unchecking
the box may provide some extra security from hackers.
WAN Port
Speed:
You may set the port speed of the Internet port to 10 Mbps, 100 Mbps, or
Auto (recommended).
Enable
Multicast
Streams:
Check the box to allow multicast trac to pass through the router from the
Internet (IPv4).
53D-Link DIR-809 User Manual
Section 3 - Conguration
This Wizard helps you add wireless devices to the wireless network.
The wizard will either display the wireless network settings to guide you through manual conguration, prompt you to enter the
PIN for the device, or ask you to press the conguration button on the device. If the device supports Wi-Fi Protected Setup and has a
conguration button, you can add it to the network by pressing the conguration button on the device and then the on the router
within 120 seconds. The status LED on the router will ash three times if the device has been successfully added to the network.
There are several ways to add a wireless device to your network. A “registrar” controls access to the wireless network. A registrar
only allows devices onto the wireless network if you have entered the PIN, or pressed a special Wi-Fi Protected Setup button on the
device. The router acts as a registrar for the network, although other devices may act as a registrar as well.
Add Wireless
You can also simply press and hold the WPS button for one second on the back of the router
or until the WPS indicator LED begins ashing, and then press the WPS button on your
wireless client to automatically connect without logging into the router.
Refer to page 69 for more information.
WPS Button
WPS Button
54D-Link DIR-809 User Manual
Section 3 - Conguration
Wi-Fi Protected Setup
Wi-Fi Protected Setup (WPS) System is a simplied method for securing your wireless network during the “Initial setup” as well
as the “Add New Device” processes. The Wi-Fi Alliance (WFA) has certied it across dierent products as well as manufactures.
The process is just as easy as pressing a button for the Push-Button Method or correctly entering the 8-digit code for the Pin
Code Method. The time reduction in setup and ease of use are quite benecial, while the highest wireless Security setting of
WPA2 is automatically used.
Enable: Enable the Wi-Fi Protected Setup feature.
Current PIN: Note: if this option is unchecked, the WPS button on the side of the router will
be disabled.
Reset PIN to Shows the current PIN.
Default: Restore the default PIN of the router.
Generate
New PIN:
Create a random number that is a valid PIN. This becomes the router’s PIN.
You can then copy this PIN to the user interface of the wireless client.
55D-Link DIR-809 User Manual
Section 3 - Conguration
Step 1: In this step the user have two options to choose from. You can choose Auto if the
wireless client supports WPS, or Manual if the wireless client does not support WPS.
Click on the Prev button to return to the previous page. Click on the Next button to
continue to the next page. Click on the Cancel button to discard the changes made and
return to the main wireless page.
Wi-Fi Protected Setup Wizard
Wireless Settings: Wi-Fi Protected Setup Wizard
If your Wireless Clients support the WPS connection method, this Wi-Fi Protected Setup Wizard can be used to initiate a wireless connection be-
tween this device and Wireless clients with a simple click of the WPS button. The Wi-Fi Protected Setup Wizard is specially designed to assist basic
network users with a simple, step-by-step set of instructions to connect wireless clients to this router using the WPS method.
To initiate the Wi-Fi Protected Setup Wizard click on the Add Wireless Device with WPS button.
Step 2: After selecting Auto, the following page will appear. There are two ways to add
a wireless device, that supports WPS. Firstly, there is the Personal Identication Number
(PIN) method. Using this method will prompt the user to enter a PIN code. This PIN code
should be identical on the wireless client. Secondly, there is the Push Button Congura-
tion (PBC) method. Using this method will allow the wireless client to connect to this
device by similarly pressing the PBC button on it.
Click on the Prev button to return to the previous page. Click on the Next button to
continue to the next page. Click on the Cancel button to discard the changes made and
return to the main wireless page.
56D-Link DIR-809 User Manual
Section 3 - Conguration
Step 2: After selecting Manual, the following page will appear. On this page to user can
view the wireless conguration of this router. The wireless clients should congure their
wireless settings to be identical to the settings displayed on this page for a successful
connection. This option is for wireless clients that can’t use the WPS method to connect to
this device.
Click on the Prev button to return to the previous page. Click on the Next button to
continue to the next page. Click on the Cancel button to discard the changes made and
return to the main wireless page. Click on the Wireless Status button to navigate to the
Status > Wireless page to view what wireless client are connected to this device.
End of Wizard.
57D-Link DIR-809 User Manual
Section 3 - Conguration
Admin
This page will allow you to change the Administrator. You can also enable Remote Management.
Tools
Password: Enter a new password for the Administrator Login Name. The administrator can make
changes to the settings.
Enable Remote
Management:
Remote management allows the DIR-809 to be congured from the Internet by a
web browser. A username/password is still required to access the Web Management
interface.
Remote
Admin Port:
The port number used to access the DIR-809 is used in the URL. Example: http://
x.x.x.x:8080 whereas x.x.x.x is the Internet IP address of the DIR-809 and 8080 is the
port used for the Web Management interface.
58D-Link DIR-809 User Manual
Section 3 - Conguration
Time
The Time Conguration option allows you to congure, update, and maintain the correct time on the internal system clock.
From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also be congured to
automatically adjust the time when needed.
Time: Displays the current date and time of the router.
Time Zone: Select your Time Zone from the drop-down menu.
Enable
Daylight
Saving:
To select Daylight Saving time manually, select enabled or disabled, and
enter a start date and an end date for daylight saving time.
Automatically
synchronize with
D-Link’s Internet
Time Server
NTP is short for Network Time Protocol. A NTP server will synch the time and
date with your router. This will only connect to a server on the Internet, not
a local server. Check the box to enable this feature.
NTP Server
Used:
Enter the IP address of a NTP server or select one from the drop-down menu.
Manual: To manually input the time, enter the values in these elds for the Year,
Month, Day, Hour, Minute, and Second and then click Set Time.
You can also click Copy Your Computer’s Time Settings to synch the date
and time with the computer you are currently on.
59D-Link DIR-809 User Manual
Section 3 - Conguration
System
This section allows you to manage the router’s conguration settings, reboot the router, and restore the router to the factory
default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that you’ve created.
Save Settings
to Local Hard
Drive:
Use this option to save the current router conguration settings to a le on the
hard disk of the computer you are using. First, click the Save button. A le dialog
will appear, allowing you to select a location and le name for the settings.
Load Settings
from Local
Hard Drive:
Use this option to load previously saved router conguration settings. First, use
the Browse option to nd a previously saved le of conguration settings. Then,
click the Load button to transfer those settings to the router.
Restore
to Factory
Default
Settings:
This option will restore all conguration settings back to the settings that were
in eect at the time the router was shipped from the factory. Any settings that
have not been saved will be lost, including any rules that you have created. If
you want to save the current router conguration settings, use the Save button
above.
Reboot
Device:
Click to reboot the router.
60D-Link DIR-809 User Manual
Section 3 - Conguration
Firmware
You can upgrade the rmware of the access point here. Make sure the rmware you want to use is on the local hard drive of
the computer. Click on Browse to locate the rmware le to be used for the update. Please check the D-Link support website
for rmware updates at http://support.dlink.com. You can download rmware upgrades to your hard drive from this site.
Language Pack
You can change the language of the web UI by uploading available language
packs.
Browse: After you have downloaded the new rmware, click Browse to locate the
rmware update on your hard drive. Click Upload to complete the rmware
upgrade.
Upload: Once you have a rmware update on your computer, use this option to
browse for the le and then upload the information into the access point.
Browse: After you have downloaded the new language pack, click Browse to locate
the language pack le on your hard drive. Click Upload to complete the
language pack upgrade.
61D-Link DIR-809 User Manual
Section 3 - Conguration
Dynamic DNS
The DDNS feature allows you to host a server (Web, FTP, Game Server, etc…) using a domain name that you have purchased
(www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign
dynamic (changing) IP addresses. Using a DDNS service provider, your friends can enter in your domain name to connect to
your server no matter what your IP address is.
Enable
Dynamic
DNS:
Dynamic Domain Name System is a method of keeping a domain name
linked to a changing IP Address. Check the box to enable DDNS.
Server
Address:
Select your DDNS provider from the drop-down menu or enter the DDNS
server address.
Host Name: Enter the Host Name that you registered with your DDNS service provider.
Username or
Key:
Enter the Username or key for your DDNS account.
Password or
Key:
Enter the Password or key for your DDNS account.
Timeout: Enter a timeout time (in hours).
Status: Displays the current connection status.
62D-Link DIR-809 User Manual
Section 3 - Conguration
System Check
Virtual Cable
Tester (VCT)
INFO:
VCT is an advanced feature that integrates a LAN cable tester on every
Ethernet port on the router. Through the graphical user interface (GUI), VCT
can be used to remotely diagnose and report cable faults such as opens,
shorts, swaps, and impedance mismatch. This feature signicantly reduces
service calls and returns by allowing users to easily troubleshoot their cable
connections.
Ping Test: The Ping Test is used to send Ping packets to test if a computer is on the
Internet. Enter the IP address that you wish to Ping and click Ping.
Ping Results: The results of your ping attempts will be displayed here.
63D-Link DIR-809 User Manual
Section 3 - Conguration
This page displays the current information for the DIR-809. It will display the LAN, WAN (Internet), and Wireless information. If
your Internet connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed. Use
Release to disconnect from your ISP and use Renew to connect to your ISP.
If your Internet connection is set up for PPPoE, a Connect button and a Disconnect button will be displayed. Use Disconnect
to drop the PPPoE connection and use Connect to establish the PPPoE connection.
Device Info
Status
Device
Information:
Displays the router’s time and rmware version.
LAN: Displays the MAC address and the public IP settings
Internet: Displays the MAC address and the private (local) IP settings for the router.
Wireless
2.4G:
Displays the 2.4 GHz wireless MAC address and your wireless settings such
as SSID and Channel.
Wireless 5G: Displays the 5 GHz wireless MAC address and your wireless settings such as
SSID and Channel.
64D-Link DIR-809 User Manual
Section 3 - Conguration
Logs
The router automatically logs (records) events of possible interest in it’s internal memory. If there isn’t enough internal memory
for all events, logs of older events are deleted but logs of the latest events are retained. The Logs option allows you to view the
router logs. You can dene what types of events you want to view and the level of the events to view.
First Page: Click to go to the rst page.
Last Page: Click to go to the last page.
Previous: Click to go back one page.
Next: Click to go to the next page.
Clear: Clears all of the log contents.
65D-Link DIR-809 User Manual
Section 3 - Conguration
Statistics
The screen below displays the Trac Statistics. Here you can view the amount of packets that pass through the DIR-809 on both
the WAN, LAN ports and the wireless segments. The trac counter will reset if the device is rebooted.
66D-Link DIR-809 User Manual
Section 3 - Conguration
Internet Sessions
The Internet Sessions page displays full details of active Internet sessions through your router. An Internet session is a
conversation between a program or application on a LAN-side computer and a program or application on a WAN-side computer.
DIR-809
67D-Link DIR-809 User Manual
Section 3 - Conguration
The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and
MAC address of the connected wireless clients.
Wireless
68D-Link DIR-809 User Manual
Section 3 - Conguration
Support
From the Support section you can nd online help covering a number of topics.
69D-Link DIR-809 User Manual
Section 4 - Connecting to a Wireless Network
Connect a Wireless Client to your Router
WPS Button
Step 2 - Within 2 minutes, press the WPS button on your wireless client (or launch the software utility and start the WPS
process).
The easiest and most secure way to connect your wireless devices to the router is WPS (Wi-Fi Protected Setup). Most wireless
devices such as wireless adapters, media players, Blu-ray DVD players, wireless printers and cameras will have a WPS button
(or a software utility with WPS) that you can press to connect to the DIR-809 router. Please refer to your user manual for the
wireless device you want to connect to make sure you understand how to enable WPS. Once you know, follow the steps below:
Step 1 - Press and hold the WPS button on the back of DIR-809 for 1-7 seconds. If held longer than 8 seconds the router will
reset. The Internet LED on the front will start to blink.
Step 3 - Allow up to 1 minute to congure. Once the Internet light stops blinking, you will be connected and your wireless
connection will be secure with WPA2.
WPS Button
70D-Link DIR-809 User Manual
Section 4 - Connecting to a Wireless Network
Windows® 8
WPA/WPA2
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before conguring your
wireless adapter. If you are joining an existing network, you will need to know the security key (Wi-Fi password) being used.
To join an existing network, locate the wireless network icon in the taskbar, next to the
time display.
Wireless Icon
Clicking on this icon will display a list of wireless networks which are within connecting
proximity of your computer. Select the desired network by clicking on the network name.
71D-Link DIR-809 User Manual
Section 4 - Connecting to a Wireless Network
You will then be prompted to enter the network security key (Wi-Fi password) for
the wireless network. Enter the password into the box and click Next.
If you wish to use Wi-Fi Protected Setup (WPS) to connect to the router, you can also
press the WPS button on your router at the point to enable the WPS function.
When you have established a successful connection a wireless network, the word
Connected will appear next to the name of the network to which you are connected.
72D-Link DIR-809 User Manual
Section 4 - Connecting to a Wireless Network
Windows® 7
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before conguring your
wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.
1. Click on the wireless icon in your system tray (lower-right corner).
2. The utility will display any available wireless networks in your area.
Wireless Icon
WPA/WPA2
73D-Link DIR-809 User Manual
Section 4 - Connecting to a Wireless Network
3. Highlight the wireless connection with Wi-Fi name (SSID) you would
like to connect to and click the Connect button.
If you get a good signal but cannot access the Internet, check your
TCP/IP settings for your wireless adapter. Refer to the Networking
Basics section in this manual for more information.
4. The following window appears while your computer tries to
connect to the router.
74D-Link DIR-809 User Manual
Section 4 - Connecting to a Wireless Network
5. Enter the same security key or passphrase (Wi-Fi password) that is
on your router and click Connect. You can also connect by pushing
the WPS button on the router.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the security settings are correct. The
key or passphrase must be exactly the same as on the wireless router.
75D-Link DIR-809 User Manual
Section 4 - Connecting to a Wireless Network
WPS
The WPS feature of the DIR-809 can be congured using Windows® 7. Carry out the following steps to use Windows® 7 to
congure the WPS feature:
1. Click the Start button and select Computer from the Start menu.
2. Click Network on the left side.
76D-Link DIR-809 User Manual
Section 4 - Connecting to a Wireless Network
3. Double-click the DIR-809.
4. Input the WPS PIN number (on the router label or in the Setup >
Wireless Setup menu in the Router’s Web UI) and click Next.
77D-Link DIR-809 User Manual
Section 4 - Connecting to a Wireless Network
5. Type a name to identify the network.
6. To congure advanced settings, click the icon.
Click Next to continue.
78D-Link DIR-809 User Manual
Section 4 - Connecting to a Wireless Network
7. The following window appears while the router is being congured.
Wait for the conguration to complete.
8. The following window informs you that WPS on the router has
been setup successfully.
Make a note of the security key as you may need to provide this
security key if adding an older wireless device to the network in
the future.
9. Click Close to complete WPS setup.
79D-Link DIR-809 User Manual
Section 4 - Connecting to a Wireless Network
Windows Vista®
Windows Vista® users may use the built-in wireless utility. If you are using another company’s utility, please refer to the user
manual of your wireless adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option
similar to the Windows Vista® utility as seen below.
Right-click on the wireless computer icon in your system tray (lower-right
corner next to the time). Select Connect to a network.
If you receive the Wireless Networks Detected bubble, click on the
center of the bubble to access the utility.
or
The utility will display any available wireless networks in your area. Click
on a network (displayed using the SSID) and click the Connect button.
If you get a good signal but cannot access the Internet, check you TCP/
IP settings for your wireless adapter. Refer to the Networking Basics
section in this manual for more information.
80D-Link DIR-809 User Manual
Section 4 - Connecting to a Wireless Network
WPA/WPA2
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before conguring your
wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.
2. Highlight the Wi-Fi name (SSID) you would like to connect to and
click Connect.
1. Open the Windows Vista® Wireless Utility by right-clicking on the
wireless computer icon in your system tray (lower right corner of
screen). Select Connect to a network.
81D-Link DIR-809 User Manual
Section 4 - Connecting to a Wireless Network
3. Enter the same security key or passphrase (Wi-Fi password) that is on
your router and click Connect.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the security settings are correct. The
key or passphrase must be exactly the same as on the wireless router.
82D-Link DIR-809 User Manual
Section 4 - Connecting to a Wireless Network
WPS/WCN 2.0
The router supports Wi-Fi protection, referred to as WCN 2.0 in Windows Vista®. The following instructions for setting this up
depends on whether you are using Windows Vista® to congure the router or third party software.
When you rst set up the router, Wi-Fi protection is disabled and uncongured. To enjoy the benets of Wi-Fi protection, the
router must be both enabled and congured. There are three basic methods to accomplish this: use Windows Vista’s built-in
support for WCN 2.0, use software provided by a third party, or manually congure.
If you are running Windows Vista®, log into the router and click the Enable checkbox in the Basic > Wireless section. Use the
Current PIN that is displayed on the Advanced > Wi-Fi Protected Setup section or choose to click the Generate New PIN
button or Reset PIN to Default button.
If you are using third party software to set up Wi-Fi Protection, carefully follow the directions. When you are nished, proceed
to the next section to set up the newly-congured router.
83D-Link DIR-809 User Manual
Section 4 - Connecting to a Wireless Network
Windows® XP
Windows® XP users may use the built-in wireless utility (Zero Conguration Utility). The following instructions are for Service
Pack 2 users. If you are using another company’s utility, please refer to the user manual of your wireless adapter for help with
connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows® XP utility as seen below.
Right-click on the wireless computer icon in your system tray (lower-right
corner next to the time). Select View Available Wireless Networks.
If you receive the Wireless Networks Detected bubble, click on the
center of the bubble to access the utility.
or
The utility will display any available wireless networks in your area. Click
on a Wi-Fi network (displayed using the SSID) and click the Connect
button.
If you get a good signal but cannot access the Internet, check you TCP/
IP settings for your wireless adapter. Refer to the Networking Basics
section in this manual for more information.
84D-Link DIR-809 User Manual
Section 4 - Connecting to a Wireless Network
It is recommended to enable WPA on your wireless router or access point before conguring your wireless adapter. If you are
joining an existing network, you will need to know the WPA key being used.
2. Highlight the Wi-Fi network (SSID) you would like to connect
to and click Connect.
1. Open the Windows® XP Wireless Utility by right-clicking on the
wireless computer icon in your system tray (lower-right corner
of screen). Select View Available Wireless Networks.
WPA/WPA2
85D-Link DIR-809 User Manual
Section 4 - Connecting to a Wireless Network
3. The Wireless Network Connection box will appear. Enter the WPA-PSK
Wi-Fi password and click Connect.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the WPA-PSK settings are correct. The
Wi-Fi password must be exactly the same as on the wireless router.
86D-Link DIR-809 User Manual
Section 5 - Troubleshooting
Troubleshooting
This chapter provides solutions to problems that can occur during the installation and operation of the DIR-809. Read the
following descriptions if you are having problems. The examples below are illustrated in Windows® XP. If you have a dierent
operating system, the screenshots on your computer will look similar to the following examples.
1. Why can’t I access the web-based conguration utility?
When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website nor do you
have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must
be on the same IP subnet to connect to the web-based utility.
• Make sure you have an updated Java-enabled web browser. We recommend the following:
- Microsoft Internet Explorer® 9 and higher
- Mozilla Firefox 20.0 and higher
- Google™ Chrome 25.0 and higher
- Apple Safari 5.1 and higher
• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a
dierent cable or connect to a dierent port on the device if possible. If the computer is turned o, the link light may not
be on.
• Disable any Internet security software running on the computer. Software rewalls such as Zone Alarm, Black Ice, Sygate,
Norton Personal Firewall, and Windows® XP rewall may block access to the conguration pages. Check the help les included
with your rewall software for more information on disabling or conguring it.
87D-Link DIR-809 User Manual
Section 5 - Troubleshooting
• Congure your Internet settings:
• Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click
the button to restore the settings to their defaults.
• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button.
Make sure nothing is checked. Click OK.
• Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
• Close your web browser (if open) and open it.
• Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This
should open the login page for your web management.
• If you still cannot access the conguration, unplug the power to the router for 10 seconds and plug back in. Wait about 30
seconds and try accessing the conguration. If you have multiple computers, try connecting using a dierent computer.
2. What can I do if I forgot my password?
If you forgot your password, you must reset your router. Unfortunately this process will change all your settings back to the
factory defaults.
To reset the router, locate the reset button (hole) on the rear panel of the unit. With the router powered on, use a paperclip
to hold the button down for 10 seconds. Release the button and the router will go through its reboot process. Wait about 30
seconds to access the router. The default IP address is 192.168.0.1. When logging in, the username is admin and leave the
password box empty.
88D-Link DIR-809 User Manual
Section 5 - Troubleshooting
3. Why can’t I connect to certain sites or send and receive emails when connecting through my router?
If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail,
we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc).
To nd the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to. A destination could be
another computer, or a URL.
• Click on Start and then click Run.
• Windows® 95, 98, and Me users type in command (Windows® NT, 2000, XP, Vista®, and 7 users type in cmd) and
press Enter (or click OK).
• Once the window opens, you’ll need to do a special ping. Use the following syntax:
ping [url] [-f] [-l] [MTU value]
Example: ping yahoo.com -f -l 1472
89D-Link DIR-809 User Manual
Section 5 - Troubleshooting
You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented
packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the
proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480).
Once you nd your MTU, you can now congure your router with the proper MTU size.
To change the MTU rate on your router follow the steps below:
• Open your browser, enter the IP address of your router (192.168.0.1) and click OK.
• Enter your username (admin) and password (blank by default). Click OK to enter the web conguration page
for the device.
• Click on Setup and then click Manual Congure.
• To change the MTU enter the number in the MTU eld and click Save Settings to save your settings.
• Test your email. If changing the MTU does not resolve the problem, continue changing the MTU in increments
of ten.
90D-Link DIR-809 User Manual
Appendix A - Wireless Basics
D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless
connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link
wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able
to enjoy the freedom that wireless networking delivers.
A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of
wires. Wireless LANs are used increasingly in both home and oce environments, and public areas such as airports, coee shops
and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more eciently.
Increased mobility and the absence of cabling and other xed infrastructure have proven to be benecial for many users.
Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop
systems support the same protocols as Ethernet adapter cards.
Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to
use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide
this link.
Wireless Basics
91D-Link DIR-809 User Manual
Appendix A - Wireless Basics
What is Wireless?
Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio
frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or oce network.
Why D-Link Wireless?
D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link
delivers the performance you need at a price you can aord. D-Link has all the products you need to build your network.
How does wireless work?
Wireless works similar to how cordless phone work, through radio signals to transmit data from one point A to point B. But
wireless technology has restrictions as to how you can access the network. You must be within the wireless network range area
to be able to connect your computer. There are two dierent types of wireless networks Wireless Local Area Network (WLAN),
and Wireless Personal Area Network (WPAN).
Wireless Local Area Network (WLAN)
In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has
a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point
as seen in the picture, the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles
to serve places like manufacturing plants, industrial locations, college and high school campuses, airports, golf courses, and
many other outdoor venues.
92D-Link DIR-809 User Manual
Appendix A - Wireless Basics
Wireless Personal Area Network (WPAN)
Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to
30 feet away.
Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as
much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other
devices that operate on batteries.
Who uses wireless?
Wireless technology as become so popular in recent years that almost everyone is using it, whether it’s for home, oce, business,
D-Link has a wireless solution for it.
Home
• Gives everyone at home broadband access
• Surf the web, check email, instant message, etc.
• Gets rid of the cables around the house
• Simple and easy to use
Small Oce and Home Oce
• Stay on top of everything at home as you would at oce
• Remotely access your oce network from home
• Share Internet connection and printer with multiple computers
• No need to dedicate oce space
93D-Link DIR-809 User Manual
Appendix A - Wireless Basics
Where is wireless used?
Wireless technology is expanding everywhere not just at home or oce. People like the freedom of mobility and it’s becoming
so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public
places is usually called “hotspots”.
Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations
like: Airports, Hotels, Coee Shops, Libraries, Restaurants, and Convention Centers.
Wireless network is easy to setup, but if you’re installing it for the rst time it could be quite a task not knowing where to start.
That’s why we’ve put together a few setup steps and tips to help you through the process of setting up a wireless network.
Tips
Here are a few things to keep in mind, when you install a wireless network.
Centralize your router or Access Point
Make sure you place the router/access point in a centralized location within your network for the best performance. Try to
place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have
a two-story home, you may need a repeater to boost the signal to extend the range.
Eliminate Interference
Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access
point. This would signicantly reduce any interference that the appliances might cause since they operate on same frequency.
Security
94D-Link DIR-809 User Manual
Appendix A - Wireless Basics
Don’t let you next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on
the WPA or WEP security feature on the router. Refer to product manual for detail information on how to set it up.
There are basically two modes of networking:
• Infrastructure – All wireless clients will connect to an access point or wireless router.
• Ad-Hoc – Directly connecting to another computer, for peer-to-peer communication, using wireless network
adapters on each computer, such as two or more DIR-809 wireless network Cardbus adapters.
An Infrastructure network contains an Access Point or wireless router. All the wireless devices, or clients, will connect to the
wireless router or access point.
An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc
mode to communicate.
Wireless Modes
95D-Link DIR-809 User Manual
Appendix B - Networking Basics
Networking Basics
Check your IP address
After you install your new D-Link adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP
server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below.
Click on Start > Run. In the run box type cmd and click OK. (Windows® 7/Vista® users type cmd in the Start Search box.)
At the prompt, type ipcong and press Enter.
This will display the IP address, subnet mask, and the
default gateway of your adapter.
If the address is 0.0.0.0, check your adapter installation,
security settings, and the settings on your router.
Some rewall software programs may block a DHCP
request on newly installed adapters.
96D-Link DIR-809 User Manual
Appendix B - Networking Basics
Statically Assign an IP address
If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:
Step 1
Windows® 7 - Click on Start > Control Panel > Network and Internet > Network and Sharing Center.
Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network
Connections.
Windows® XP - Click on Start > Control Panel > Network Connections.
Windows® 2000 - From the desktop, right-click My Network Places > Properties.
Step 2
Right-click on the Local Area Connection which represents your network adapter and select Properties.
Step 3
Highlight Internet Protocol (TCP/IP) and click Properties.
Step 4
Click Use the following IP address and enter an IP address that is on the same subnet
as your network or the LAN IP address on your router.
Example: If the router´s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X
where X is a number between 2 and 99. Make sure that the number you choose is not
in use on the network. Set the Default Gateway the same as the LAN IP address of your
router (I.E. 192.168.0.1).
Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The
Secondary DNS is not needed or you may enter a DNS server from your ISP.
Step 5
Click OK twice to save your settings.
97D-Link DIR-809 User Manual
Appendix C - Technical Specications
Technical Specications
Hardware Specications
• LAN Interface: Four 10/100 Mbps LAN ports
• WAN Interface: One 10/100 Mbps Internet port
• Wireless Interface (2.4 GHz): IEEE 802.11n/g/b
• Wireless Interface (5 GHz): IEEE 802.11ac/n/a
Operating Voltage
• Input: 100~240 V (±20%), 50~60 Hz
• Output: DC 5 V, 1 A
Temperature
• Operating: 0 ~ 40 oC (32 ~ 104 oF)
• Non-Operating: -20 ~ 65 oC (-4 ~ 149 oF)
Humidity
• Operating: 10% - 90% non-condensing
• Non-Operating: 5% - 95% non-condensing
Wireless Frequency Range1
• IEEE 802.11a: 5180 MHz~5240 MHz, 5745 MHz~5825 MHz
• IEEE 802.11b: 2400 MHz~2483 MHz
• IEEE 802.11g: 2400 MHz~2484 MHz
• IEEE 802.11n: 2400 MHz~2484 MHz, 5180 MHz~5240 MHz, 5745
MHz~5825 MHz
• IEEE 802.11ac: 5180 MHz~5240 MHz, 5745 MHz~5825 MHz
Wireless Bandwidth Rate
• IEEE 802.11a: 54, 48, 36, 24, 18, 12, 9, and 6 Mbps
• IEEE 802.11b: 11, 5.5, 2, and 1 Mbps
• IEEE 802.11g: 54, 48, 36, 24, 18, 12, 9, and 6 Mbps
• IEEE 802.11n: 6.5 to 300 Mbps
• IEEE 802.11ac (draft): 6.5 to 433 Mbps
Antenna Type
• Three external antennas
Wireless Security
• WPA/WPA2-Personal, WPA/WPA2-Enterprise, WPS (PIN & PBC)
Certications
• FCC
• CE
• CSA
Dimensions & Weight
• 189.95 x 149.75 x 83.11 mm (7.48 x 5.90 x 3.27 inches)
• 227.8 grams (8.03 ounces)
Warranty
• 2 years
1 Wireless frequency range may vary according to regional regulations.