Nuclias Connect
Hardware Overview
- Front Panel
- Side Panel
Basic Installation
- Hardware Setup
Setup Wizard
Web User Interface
Knowledge Base
- Wireless Basics
- Wireless Installation Considerations
Troubleshooting
- Why can’t I access the web-based configuration utility?
Technical Specifications
Antenna Patterns

D-Link DIS-2650AP User Manual

Displayed below is the user manual for DIS-2650AP by D-Link which is a product in the Wireless Access Points category. This manual has pages.

NUCLIAS CONNECT

DIS-2650AP User Guide

V 1.00

2020 | Business Class Networking

Table of Contents

Nuclias Connect .........................................................................4

Introduction ................................................................................... 4

Nuclias Connect Key Features .................................................. 5

Package Contents ......................................................................... 6

System Requirements ................................................................. 6

Hardware Overview ..................................................................7

Front Panel ...................................................................................... 7

Side Panel ........................................................................................ 7

Basic Installation ........................................................................8

Hardware Setup ............................................................................8

Mounting the Device on a Wall ....................................... 8

Installing the Device on a DIN Rail .................................9

Installing the Device into a Rack ...................................10

Grounding the Device .......................................................11

Powering the Device .........................................................11

Using the Terminal Connections ...................................11

Connecting Devices ...........................................................13

Setup Wizard ........................................................................... 15

Web User Interface ................................................................. 16

Wireless ..........................................................................................17

Access Point Mode .............................................................17

WDS with AP Mode ............................................................19

WDS Mode ............................................................................21

Wireless Client Mode .........................................................23

Wireless Security .................................................................24

Wired Equivalent Privacy (WEP) ..............................24

Wi-Fi Protected Access (WPA / WPA2)....................25

LAN ..........................................................................................27

IPv6 ..........................................................................................28

Advanced Settings .....................................................................29

Performance .........................................................................30

Wireless Resource Control .......................................................32

Multi-SSID ..............................................................................34

VLAN ........................................................................................36

VLAN List ..........................................................................36

Port List ............................................................................. 37

Add/Edit VLAN ...............................................................38

PVID Settings ..................................................................39

Intrusion .................................................................................40

Schedule ................................................................................41

Internal RADIUS Server .....................................................42

ARP Spoong Prevention ................................................43

Bandwidth Optimization .................................................44

Hotspot 2.0 ............................................................................ 46

Hotspot ............................................................................. 46

Interworking ...................................................................47

WAN Metrics ...................................................................48

LIST .....................................................................................49

OSU ....................................................................................50

Captive Portal .......................................................................52

Authentication Settings-Web Redirection Only 52

Authentication Settings- Username/Password ..54

Authentication Settings- Passcode ........................56

Authentication Settings- Remote RADIUS ........... 58

Authentication Settings- LDAP ................................60

Authentication Settings- POP3 ................................62

MAC Bypass .....................................................................65

DHCP Server .........................................................................66

Dynamic Pool Settings ................................................ 66

Static Pool Setting ........................................................67

Current IP Mapping List ..............................................68

Filters .......................................................................................69

Wireless MAC ACL .........................................................69

IP Filter Settings ............................................................. 70

WLAN Partition ..............................................................71

Trac Control...............................................................................72

Uplink/Downlink Setting .................................................72

QoS...........................................................................................73

Trac Manager ....................................................................74

Status ..............................................................................................75

Device Information ............................................................76

Client Information ..............................................................77

WDS Information Page .....................................................78

Statistics .........................................................................................79

Ethernet Trac Statistics ..................................................79

WLAN Trac Statistics ....................................................... 80

Log ...................................................................................................81

View Log .................................................................................81

Log Settings ..........................................................................82

Maintenance Section ................................................................83

Administration ............................................................................. 84

Limit Administrator ............................................................84

System Name Settings ......................................................85

Console Settings .................................................................86

Ping Control Settings ........................................................86

LED Settings..........................................................................86

Country Settings .................................................................86

DDP Settings ........................................................................87

Nuclias Connect Settings .................................................87

Firmware and SSL Upload ................................................88

Conguration File Upload ...............................................89

Time and Date Settings ....................................................90

Conguration and System.......................................................91

System Settings ........................................................................... 92

Help .................................................................................................93

Knowledge Base ..................................................................... 94

Wireless Basics .............................................................................94

Wireless Installation Considerations .................................... 95

Troubleshooting ..................................................................... 96

Why can’t I access the web-based conguration

utility? .....................................................................................96

What can I do if I forgot my password? .......................96

How to check your IP address? ......................................97

How to statically assign an IP address? ....................... 98

Technical Specications ........................................................ 99

Antenna Patterns .................................................................100

Nuclias Connect

Introduction

Nuclias Connect is D-Link’s centralized management solution for Small-to-Medium-Sized Business (SMB) networks. Nuclias Connect makes it easier

to analyze, automate, congure, optimize, scale, and secure your network — delivering the convenience of an Enterprise-wide management

solution, at an SMB price. Nuclias Connect gives you the nancial and technical exibility to expand from a small network to a larger one (up

to 1,000 APs), while retaining a robust and centralized management system. And with its intuitive Graphical User Interface (GUI), a wealth of

enhanced AP features, and a setup wizard that supports 11 languages, Nuclias Connect minimizes the hassle of deployment, conguration,

and administration tasks.

Deployable on Windows server (or Linux via Docker), PC, or Smartphone (via lite management app) the Nuclias Connect free-to-download

software is capable of managing up to 1,000 Access Points (APs) without licensing charges, coupled with an inexpensive optional

hardware controller (The Hub) suitable for remote locations. Through software-based monitoring and remote management of all wireless Access

Points (APs) on your network, Nuclias Connect oers tremendous exibility compared to traditional hardware-based unied

management systems. Conguration can be done remotely. Network trac analytics are available at a glance (in whole or in part). Load Balancing,

Airtime Fairness, and Localized Throttling are enabled.

Nuclias Connect supports multi-tenancy, so network admins can grant localized management authority for local networks. In addition, because

APs can support 8 SSIDs per radio (16 SSIDs per dual band APs), administrators have the option of using one SSID to create a guest network for

visitors.

Nuclias Connect provides direct AP discovery and provisioning when it shares the same Layer-2/Layer-3 network with a given AP, allowing

users to nd APs and import proles with minimum eort, which can be applied as needed to groups or individual APs for even more eective

conguration.

Since Nuclias Connect’s software operates transparently on the network, an AP can be deployed anywhere in an NAT environment. Admins can

provide & manage a variety of distributed deployments, including setting & admin account conguration for each deployment.

Nuclias Connect allows for multiple user authentications while enabling specic access control congurations for each SSID, giving admins the

option of conguring separate internal networks for dierent subnets, while enabling more advanced Value-Added Services, such as Captive

Portal or Wi-Fi Hotspot.

Nuclias Connect

Nuclias Connect Key Features

• Free-to-Download Management Software

• Searchable Event Log and Change Log

• License-Free Access Points

• Trac Reporting & Analytics

• Authentication via Customizable Captive Portal, 802.1x and RADIUS Server, POP3, LDAP, AD

• Remote Cong. & Batch Cong.

• Multilingual Support

• Intuitive Interface

• Multi-Tenant & Role-Based Administration

• Payment Gateway (Paypal) Integration and Front-Desk Ticket Management

For more information on how to use Nuclias Connect with DIS-2650AP, please refer to the Nuclias Connect User Guide.

Nuclias Connect

Package Contents

• DIS-2650AP

• Quick Installation Guide

• DIN rail mounting kit

• 4 installation scres (3 x 7 mm)

• Bracket

System Requirements

yComputers with Windows®, Macintosh®, or Linux-based operating systems with an Ethernet Adapter

yInternet Explorer 11, Safari 7, Firefox 28, or Google Chrome 33 and above (for web-based conguration)

Hardware Overview

Front Panel

2Power Receptor Connect the supplied power adapter.

3LAN (PoE) Port Connect to a Power over Ethernet (PoE) switch or router

via an Ethernet cable.

4Reset Button

Press and hold for ve seconds to reset the access point

to the factory default settings. Press and hold for one

second to reboot the access point.

1Power/Status

Solid Red Indicates the access point has malfunctioned.

Blinking Red This LED will blink during boot-up.

Solid Green Indicates that the DIS-2650AP is working

properly.

DIS-2650AP

5G 2.4G ALARM POE PWR2 PWR1STATUS SIGNAL

CONSOLE RESET LAN2 LAN1/ POE

134

Side Panel

Basic Installation

Hardware Setup

Mounting the Device on a Wall

The DIS-2650AP can be installed on a solid surface by using the included wall mounting plates attached to the back of the device. Use the following

instructions to install the DIS-2650AP on a wall:

1. Align the cross-section of the mounting plates with the openings on the back of the device. Secure the plates with the included mounting screws.

2. Remove the DIN rail mounting clip from the back of the device (if present).

3. Place the mounting brackets (attached to the device) on the location where you want to mount it, and use the brackets as a guide to mark

where to drill the screw holes.

4. Drill holes on the marks and insert wall anchors appropriate for the material of the wall.

5. Align the device with the wall anchors and secure it to the wall using appropriate screws for the wall anchors.

Basic Installation

Installing the Device on a DIN Rail

The DIS-2650AP can be mounted on a standard DIN rail using the included DIN mounting kit.

Use the following instructions to install the DIS-2650AP on a rail:

1. Check that the DIN rail is installed properly using at least two screws on each end.

2. Fasten the DIN mounting clip to the rear panel of the device using the included mounting screws.

3. Position the DIS-2650AP against the rail, then tilt it upwards and hook the DIN rail clip on the back of the device against the rail. Snap the device

into place to complete the installation.

Basic Installation

Installing the Device into a Rack

The DIS-2650AP can be mounted on a standard rack using the included mounting plates. To install the device on a rack:

1. Attach the mounting brackets to the rear panel of the device using the provided installation screws.

2. Use the provided screws to attach the two rear mounting plates to the rack.

Basic Installation

Grounding the Device

To use the DIS-2650AP safely, it needs to be grounded. Please complete these steps before powering on the device.

1. Remove the grounding screw from the top of the DIS-2650AP and place the grounding cable lug ring on top of the grounding screw opening.

2. Insert the grounding screw back into the grounding screw opening and use a screwdriver to tighten the grounding screw, securing the grounding

cable to the DIS-2650AP.

3. Attach the terminal lug ring at the other end of the grounding cable to an appropriate grounding source.

Powering the Device

The DIS-2650AP can be powered with an 802.3at PoE source or by using the built-in terminal adapter. This allows dual power inputs using wires

from the power source(s) to be screwed into the terminal connections.

Using the Terminal Connections

1. Before continuing, consult the diagram below to decide which wires from the power source need to connect to which contacts on the terminal

block. Note that two power sources can be used; one inserted into V1-/V1+ (labeled PWR 1) and the other inserted into V2-/V2+ (labeled PWR2).

Basic Installation

2. Use a lever to remove the terminal block from the switch.

3. Use a at head screwdriver to unscrew the terminal connections that you wish to use.

4. Insert the wires into the terminal connectiosn and use the screwdriver to tighten the screws to secure the wires.

5. Re-insert the terminal block into the socket on the device.

Basic Installation

Connecting Devices

The Ethernet port can be connected to an end device. Use a standard Category 5/5e/6 RJ-45 Ethernet cable to connect the end device to the

DIS-2650AP.

The port will auto-negotiate to the highest possible port speed based on the connected device.

Basic Installation

To set up and manage the DIS-2650AP, use one of the following methods:

1. Connect the access point and your computer to the same PoE switch. Manage the access point from the computer.

Enter dis2650ap.local in the address eld of your browser.

Username: admin

Password: admin

2. Connect the access point and your computer via DPE-311GI PoE injector. Manage the access point from the computer.

Enter dis2650ap.local in the address eld of your browser.

Username: admin

Password: admin

3. Connect the access point and your computer to the same network switch. Manage the access point from the computer.

Enter dis2650ap.local in the address eld on your browser.

Username: admin

Password: admin

Setup Wizard

The rst login instance displays the System Settings window which requires a change in password. Additional settings include the System Time

and System Country functions.

After logging in to the user interface, ll in the New Password and Conrm New Password elds.

In the System Time function, select Using Network Time Protocol (NTP) or Manually to dene the system time. If required, click the Daylight Sav-

ing Oset drop-down menu and select the value (minutes).

ySetting NTP System Time: Before trying to congure NTP check, perform a ping test with the NTP server. In the NTP Server eld, enter the NTP

server to use. Then click the Time Zone drop-down menu and select the appropriate time zone.

ySetting System Time Manually: From the System Date drop-down menu, select the Year, Month, and Day along with the Hour and Minutes ap-

propriate for the AP.

yEnable Daylight Saving: Click the radio button to enable the daylight savings time (DST) function. Set the DST start (24 hours) and end (24

hours) time by clicking on the drop-down menus and setting the Month, Week, Day, Hour, and Minute of the DST starting days.

Once the settings are congured, click Update button to accept the conguration and proceed to the main interface menu page.

Web User Interface

The DIS-2650AP supports an elaborate web user interface where the user can congure and monitor the device. Launch a web browser, type

in http://dis2650ap.local and then press Enter to login. The default username and password is: admin Most of the congurable settings are

located in the menu on the left side of the web GUI which contains sections called Basic Settings, Advanced Settings and Status.

Web User Interface

Wireless

On the wireless settings page, you can setup the basic wireless conguration for the access point. The user can choose from 4 dierent wireless

modes:

• Access Point - Used to create a wireless LAN

• WDS with AP - Used to connect multiple wireless networks while still functioning as a wireless access point

• WDS - Used to connect multiple wireless networks

• Wireless Client - Used when the access point needs to act as a wireless network adapter for an Ethernet enabled device

Wireless Band:

Mode:

Network Name (SSID):

SSID Visibility:

Auto Channel Selection:

Select either 2.4 GHz or 5 GHz from the drop-down

menu.

Select Access Point from the drop-down menu.

Service Set Identier (SSID) is the name designated

for a specic wireless local area network (WLAN).

The SSID’s factory default setting is dlink. The SSID

can be easily changed to connect to an existing

wireless network or to establish a new wireless

network. The SSID can be up to 32 characters and

is case-sensitive.

Select Enable to broadcast the SSID across the

network, thus making it visible to all network users.

Select Disable to hide the SSID from the network.

This feature when enabled automatically selects

the channel that provides the best wireless

performance. The channel selection process only

occurs when the AP is booting up. To manually

select a channel, set this option to Disable and

select a channel from the drop-down menu.

Access Point Mode

Web User Interface

Channel:

Channel Width:

Authentication:

802.11k/v/r:

To change the channel, rst toggle the Auto Channel Selection setting to Disable, and then use the drop-down menu to make

the desired selection.

Note: The wireless adapters will automatically scan and match the wireless settings.

Allows you to select the channel width you would like to operate in. Select 20 MHz if you are not using any 802.11n wireless

clients. Auto 20/40 MHz allows you to connect to both 802.11n and 802.11b/g or 802.11a wireless devices on your network.

Use the drop-down menu to choose Open System, Shared Key, WPA-Personal, WPA-Enterprise, or 802.1x.

• Select Open System to communicate the key across the network (WEP).

• Select Shared Key to limit communication to only those devices that share the same WEP settings. If multi-SSID is

enabled, this option is not available.

• Select WPA-Personal to secure your network using a password and dynamic key. No RADIUS server is required.

• Select WPA-Enterprise to secure your network with the inclusion of a RADIUS server.

• Select 802.1X if your network is using port-based Network Access Control.

Use the drop-down menu to choose to enable or disable 802.11k/v/r

Web User Interface

Wireless Band:

Mode:

Network Name (SSID):

SSID Visibility:

Auto Channel Selection:

Channel:

Channel Width:

Select either 2.4GHz or 5GHz from the drop-down

menu.

WDS with AP mode is selected from the drop-down

menu.

Service Set Identier (SSID) is the name designated

for a specic wireless local area network (WLAN).

The SSID’s factory default setting is dlink. The SSID

can be easily changed to connect to an existing

wireless network or to establish a new wireless

network.

Enable or Disable SSID visibility. Enabling this

feature broadcasts the SSID across the network,

thus making it visible to all network users.

Enabling this feature automatically selects

the channel that will provide the best wireless

performance. This feature is not supported in WDS

with AP mode. The channel selection process only

occurs when the AP is booting up.

All devices on the network must share the same

channel. To change the channel, use the drop-down

menu to make the desired selection. (Note: The

wireless adapters will automatically scan and match

the wireless settings.)

Allows you to select the channel width you would

like to operate in. Select 20 MHz if you are not using

any 802.11n wireless clients. Auto 20/40 MHz allows

you to connect to both 802.11n and 802.11b/g or

802.11a wireless devices on your network.

WDS with AP Mode

Web User Interface

Remote AP MAC

Address:

Site Survey:

Authentication:

Enter the MAC addresses of the APs on your network that will serve as bridges to wirelessly connect multiple networks.

Click on the Scan button to search for available wireless networks, then click on the available network that you want to

connect with.

Use the drop-down menu to choose Open System, or WPA-Personal.

• Select Open System to communicate the key across the network.

• Select WPA-Personal to secure your network using a password and dynamic key changes. No RADIUS server is required.

Web User Interface

Wireless Band:

Mode:

Network Name (SSID):

Auto Channel

Selection:

Channel:

Channel Width:

Remote AP MAC

Address:

Select either 2.4GHz or 5GHz from the drop-down

menu.

WDS is selected from the drop-down menu.

Service Set Identier (SSID) is the name designated

for a specic wireless local area network (WLAN). The

SSID’s factory default setting is dlink. The SSID can

be easily changed to connect to an existing wireless

network or to establish a new wireless network.

Enabling this feature automatically selects

the channel that will provide the best wireless

performance. This feature is not supported in WDS

mode.

All devices on the network must share the same

channel. To change the channel, use the drop-down

menu to make the desired selection.

Use the drop-down menu to choose 20 MHz or

Auto 20/40 MHz.

Enter the MAC addresses of the APs on your network

that will serve as bridges to wirelessly connect

multiple networks.

WDS Mode

Web User Interface

Site Survey:

Authentication:

Click on the Scan button to search for available wireless networks, then click on the available network that you

want to connect with.

Use the drop-down menu to choose Open System, or WPA-Personal.

• Select Open System to communicate the key across the network.

• Select WPA-Personal to secure your network using a password and dynamic key changes. No RADIUS server is

required.

Web User Interface

Wireless Band:

Mode:

Network Name (SSID):

SSID Visibility:

Auto Channel Selection:

Channel:

Channel Width:

Site Survey:

Authentication:

Select either 2.4 GHz or 5 GHz from the drop-down

menu.

Wireless Client is selected from the drop-down menu.

Service Set Identier (SSID) is the name designated

for a specic wireless local area network (WLAN). The

SSID’s factory default setting is dlink. The SSID can

be easily changed to connect to an existing wireless

network.

This option is unavailable in Wireless Client mode.

Enabling this feature automatically selects the channel

that will provide the best wireless performance. This

feature is not supported in Wireless Client mode.

The channel used will be displayed, and matches the

AP that the DIS-2650AP is connected to when set to

Wireless Client mode.

Use the drop-down menu to choose 20 MHz or Auto

20/40 MHz.

Click on the Scan button to search for available

wireless networks, then click on the available network

that you want to connect with.

Will be explained in the next topic.

Wireless Client Mode

Web User Interface

Wireless security is a key concern for any wireless network installed. Wireless networks will broadcast it’s presence for anyone to connect to it. Today, wireless

security has advanced to a level where it is virtually impenetrable.

There are mainly two forms of wireless encryption and they are called Wired Equivalent Privacy (WEP) and Wi-Fi Protected Access (WPA). WEP was the rst

security method developed. It is a low level encryption but better than no encryption. WPA is the newest encryption protocol. With the advanced WPA2

standard wireless networks have nally reach a point where the security is strong enough to give users the peace of mind when installing wireless networks.

Wireless Security

Wired Equivalent Privacy (WEP)

Encryption:

Key Type*,**:

Key Size:

Key Index (1-4):

Key:

Use the radio button to disable or enable

encryption.

Select HEX or ASCII.

Select 64 Bits or 128 Bits.

Select the 1st through the 4th key to be the active

key.

Input up to four keys for encryption. You will select

one of these keys in the Key Index drop-down

menu.

**Hexadecimal (HEX) digits consist of the numbers 0-9 and the letters A-F.

*ASCII (American Standard Code for Information Interchange) is a code that represents English letters using

numbers ranging from 0-127.

WEP provides two variations called Open System and Shared Key.

Open System sends a request to the access point and if the key used matches the one congured on the access point, the access point will return a success

message back to the wireless client. If the key does not match the one congured on the access point, the access point will deny the connection request from

the wireless client.

Shared Key sends a request to the access point and if the key used matches the one congured on the access point, the access point will send a challenge

to the client. The client will then again send a conrmation of the same key back to the access point where the access point will either return a successful or a

denial packet back to the wireless client.

Web User Interface

Wi-Fi Protected Access (WPA / WPA2)

WPA was created by the Wi-Fi Alliance to address the limitations and weaknesses found in WEP. This protocol is mainly based on the 802.11i standard.

There are also two variations found in WPA called WPA-Personal (PSK) and WPA-Enterprise (EAP).

WPA-Enterprise requires the user to install a Radius Server on the network for authentication.

WPA-Personal does not require the user to install a Radius Server on the network.

Comparing WPA-PSK with WPA-EAP, WPA-PSK is seen as a weaker authentication but comparing WPA-PSK to WEP, WPA-PSK is far more secure than

WEP. WPA-EAP is the highest level of wireless security a user can use for wireless today.

WPA2 is an upgrade of WPA. WPA2 yet again solves some possible security issues found in WPA. WPA2 has two variations called WPA2-Personal (PSK)

and WPA2-Enterprise (EAP) which is the same as found with WPA.

WPA Mode:

Cipher Type:

Group Key Update:

Pass Phrase:

When WPA-Personal is selected for Authentication type,

you must also select a WPA mode from the drop-down

menu: AUTO (WPA or WPA2), WPA2 Only, or WPA Only.

WPA and WPA2 use dierent algorithms. AUTO (WPA or

WPA2) allows you to use both WPA and WPA2.

When you select WPA-Personal, you must also select AUTO,

AES, or TKIP from the pull down menu.

Select the interval during which the group key will be valid.

The default value of 1800 is recommended.

When you select WPA-Personal, please enter a Pass Phrase

in the corresponding eld.

Web User Interface

WPA Mode:

Cipher Type:

Group Key Update Interval:

Network Access Protection:

RADIUS Server:

RADIUS Port:

RADIUS Secret:

Account Server:

Account Port:

Account Secret:

When WPA-Enterprise is selected, you must also

select a WPA mode from the drop-down menu:

AUTO (WPA or WPA2), WPA2 Only, or WPA Only.

WPA and WPA2 use dierent algorithms. AUTO

(WPA or WPA2) allows you to use both WPA and

WPA2.

When WPA-Enterprise is selected, you must also

select a cipher type from the drop-down menu:

Auto, AES, or TKIP.

Select the interval during which the group key

will be valid. 1800 is the recommended value as

a lower interval may reduce data transfer rates.

Enable or disable Microsoft Network Access

Protection.

Enter the IP address of the RADIUS server.

Enter the RADIUS port.

Enter the RADIUS secret.

Enter the IP address of the Account Server.

Enter the Account port.

Enter the Account secret.

Web User Interface

LAN

LAN is short for Local Area Network. This is considered your internal network. These are the IP settings of the LAN interface for the DIS-2650AP.

These settings may be referred to as private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal

network and cannot be seen on the Internet.

Get IP From:

IP Address:

Subnet Mask:

Default Gateway:

DNS:

Dynamic IP (DHCP) is chosen here. Choose this option if

you have a DHCP server in your network. When Dynamic

IP (DHCP) is selected, the other elds here will be grayed

out. Please allow about 2 minutes for the DHCP client to

be functional once this selection is made. If you wish

to assign a static IP address to the DIS-2650AP, choose

Static IP (Manual).

Assign a static IP address that is within the IP address

range of your network.

Enter the subnet mask. All devices in the network must

share the same subnet mask.

Enter the IP address of the gateway/router in your

network.

Enter a DNS server IP address. This is usually the local IP

address of your gateway/router.

Web User Interface

IPv6

Enable IPv6:

Get IP From:

IP Address:

Prex:

Default Gateway:

Check to enable the IPv6

Auto is chosen here. Choose this option the DIS-2650AP

can get IPv6 address automatically or use Static to set

IPv6 address manually.

Other elds here will be grayed out when Auto is selected.

Enter the LAN IPv6 address used here.

Enter the LAN subnet prex length value used here.

Enter the LAN default gateway IPv6 address used here.

Web User Interface

Advanced Settings

In the Advanced Settings Section users can congure advanced settings concerning Performance, Multiple SSID, VLAN, Security, Quality of Service, AP Array,

Web Redirection, DHCP Server, Filters and Scheduling. The following pages will explain settings found in the Advanced Settings section in more detail.

Web User Interface

Performance

On the Performance Settings page users can congure more advanced settings concerning the wireless signal and hosting.

Wireless Band:

Wireless:

Wireless Mode:

Data Rate*:

Beacon Interval (40-

500):

DTM Interval (1-15):

Select either 2.4GHz or 5GHz.

Use the drop-down menu to turn the wireless function On or O.

The dierent combinations of clients that can be supported include

Mixed 802.11n, 802.11g and 802.11b, Mixed 802.11g and 802.11b

and 802.11n Only in the 2.4 GHz band and Mixed 802.11n, 802.11a,

802.11a only, and 802.11n Only in the 5 GHz band. Please note that

when backwards compatibility is enabled for legacy (802.11a/g/b)

clients, degradation of 802.11n (draft) wireless performance is

expected.

Indicate the base transfer rate of wireless adapters on the wireless

LAN. The AP will adjust the base transfer rate depending on the base

rate of the connected device. If there are obstacles or interference, the

AP will step down the rate. This option is enabled in Mixed 802.11g

and 802.11b mode (for 2.4 GHz) and 802.11a only mode (for 5 GHz).

The choices available are Best (Up to 54), 54, 48, 36, 24, 18, 12, 9, 6

for 5 GHz and Best (Up to 54), 54, 48, 36, 24, 18, 12, 9, 6, 11, 5.5, 2 or

1 for 2.4 GHz.

Beacons are packets sent by an access point to synchronize a

wireless network. Specify a value in milliseconds. The default (100)

is recommended. Setting a higher beacon interval can help to save

the power of wireless clients, while setting a lower one can help a

wireless client connect to an access point faster.

Select a Delivery Trac Indication Message setting between 1 and 15. 1 is the default setting. DTIM is a countdown informing

clients of the next window for listening to broadcast and multicast messages.

Web User Interface

Transmit Power:

WMM (Wi-Fi

Multimedia):

Ack Time Out

(2.4 GHZ, 64~200):

Short GI:

IGMP Snooping:

Multicast Rate:

Multicast Bandwidth

Control :

Maximum Multicast

Bandwidth :

HT20/40 Coexistence :

Transfer DHCP Oer

to Unicast :

PMF:

This setting determines the power level of the wireless transmission. Transmitting power can be adjusted to eliminate the

overlapping of wireless area coverage between two access points where interference is a major concern. For example, if wireless

coverage is intended for half of the area, then select 50% as the option. Use the drop-down menu to select 100%, 50%, 25%, or

12.5%.

WMM stands for Wi-Fi Multimedia. Enabling this feature will improve the user experience for audio and video applications over

a Wi-Fi network.

To eectively optimize throughput over long distance links enter a value for Acknowledgement Time Out between 25 and 200

microseconds for 5 GHz or from 64 to 200 microseconds in the 2.4 GHz in the eld provided.

Select Enable or Disable. Enabling a short guard interval can increase throughput. However, be aware that it can also increase

the error rate in some installations due to increased sensitivity to radio-frequency installations.

Select Enable or Disable. Internet Group Management Protocol allows the AP to recognize IGMP queries and reports sent between

routers and an IGMP host (wireless STA). When IGMP snooping is enabled, the AP will forward multicast packets to an IGMP host

based on IGMP messages passing through the AP.

Adjust the multicast packet data rate here. The multicast rate is supported in AP mode, (2.4 GHZ and 5 GHZ) and WDS with AP

mode, including Multi-SSIDs.

Adjust the multicast packet data rate here. The multicast rate is supported in AP mode, and WDS with AP mode, including Multi-

SSIDs

Set the multicast packets maximum bandwidth pass through rate from the Ethernet interface to the Access Point.

Enable this option to reduce interference from other wireless networks in your area. If the channel width is operating at 40MHz

and there is another wireless network’s channel over-lapping and causing interference, the Access Point will automatically change

to 20MHz.

Enable to transfer the DHCP Oer to Unicast from LAN to WLAN, suggest to enable this function if stations number is larger than 30.

Enable this option to help protect clients against forged management frames spoofed from other devices that might otherwise

disrupt a valid user session.

Web User Interface

Wireless Resource Control

The Wireless Resource Control window is used to congure the wireless connection settings so that the device can detect the best wireless con-

nection in your environment.

Airtime Fairness:

Wireless band:

Band Steering:

Band Steering Age:

Band Steering

Dierence:

Band Steering

Refuse Number:

Connection Limit:

Enable airtime fairness to help regulate downlink

airtime.

Select 2.4GHz or 5GHz.

Use the drop-down menu to Enable the 5G Preferred

function. When the wireless clients support both

2.4GHz and 5GHz and the 2.4GHz signal is not strong

enough, the device will use 5G as higher priority.

Enter the time in seconds to specify the interval of

updating information.

The 5G preferred dierence value is equal to the

number of 5GHz wireless client connections minus

the number of 2.4GHz wireless client connections.

If the number of 5GHz wireless client connections

minus the number of 2.4GHz wireless client connec-

tions exceed this value, the extra 5GHz wireless client

connections will be forced to connect to the 2.4GHz

band and not the 5GHz band.

Enter the maximum 5G connection attempts allowed before the 5G preferred function will be disabled for the wireless

station connection.

Select Enable or Disable. This is an option for load balancing. This determines whether to limit the number of users

accessing this device. The exact number is entered in the User Limit eld below. This feature allows the user to share

the wireless network trac and the client using multiple APs. If this function is enabled and when the number of users

exceeds this value, or the network utilization of this AP exceeds the percentage that has been specied, the DIS-2650AP

will not allow clients to associate with the AP.

Web User Interface

User Limit:

11n Preferred:

Network Utilization:

Aging out:

RSSI Threshold:

Data Rate Threshold:

ACL RSSI:

ACL RSSI Threshold:

Set the maximum amount of users that are allowed access (zero to 64 users) to the device using the specied wireless

band. The default setting is 20.

Use the drop-down menu to Enable the 11n Preferred function. The wireless clients with 802.11n protocol will have

higher priority to connect to the device.

Set the maximum utilization of this access point for service. The DIS-2650AP will not allow any new clients to associate

with the AP if the utilization exceeds the value the user species. Select a utilization percentage between 100%, 80%,

60%, 40%, 20%, or 0%. When this network utilization threshold is reached, the device will pause one minute to allow net-

work congestion to dissipate.

Use the drop-down menu to select the criteria of disconnecting the wireless clients. Available options are RSSI and Data

Rate.

When RSSI is selected in the Aging out drop-down menu, select the percentage of RSSI here. When the RSSI of wireless

clients is lower than the specied percentage, the device disconnects the wireless clients.

When Data Rate is selected in the Aging out drop-down menu, select the threshold of data rate here. When the data

rate of wireless clients is lower than the specied number, the device disconnects the wireless clients.

Use the drop-down menu to Enable the function. When enabled, the device denies the connection request from the

wireless clients with the RSSI lower than the specied threshold below.

Set the ACL RSSI Threshold.

Web User Interface

Multi-SSID

This device supports up to four multiple Service Set Identiers. You can set the Primary SSID under Basic > Wireless. The SSID’s factory default setting

is dlink. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network.

Enable Multi-

SSID:

Enable Priority:

Band:

Index:

SSID:

SSID Visibility:

Security:

Priority:

WMM (Wi-Fi

Multimedia):

Check to enable support for multiple SSIDs.

Check to enable support for SSID priority level.

Select 2.4GHz or 5GHz.

You can select up to seven multi-SSIDs. With the Primary

SSID, you have a total of eight multi-SSIDs.

Service Set Identier (SSID) is the name designated for a

specic wireless local area network (WLAN). The SSID’s

factory default setting is dlink. The SSID can be easily

changed to connect to an existing wireless network or to

establish a new wireless network.

Enable or Disable SSID visibility. Enabling this feature

broadcasts the SSID across the network, thus making it

visible to all network users.

The Multi-SSID security can be Open System, WPA-

Personal, or WPA-Enterprise. For a detailed description of

the Open System parameters please go to page 23. For

a detailed description of the WPA-Personal parameters

please go to page 24. For a detailed description of the

WPA-Enterprise parameters please go to page 25.

Select the priority level of the SSID selected.

WMM stands for Wi-Fi Multimedia. Enabling this feature

will improve the user experience for audio and video

applications over a Wi-Fi network.

Web User Interface

Encryption:

Key Type:

Key Size:

Key Index (1-4):

Key:

WPA Mode:

Cipher Type:

Group Key Update Interval:

Pass Phrase:

Conrm Pass Phrase:

RADIUS Server:

RADIUS Port:

RADIUS Secret:

When you select Open System, toggle between Enable and Disable. If Enable is selected, the Key Type, Key Size, Key Index

(1~4), Key, and Conrm Keys must also be congured.

Select HEX or ASCII.

Select 64-bit or 128-bit.

Select from the 1st to 4th key to be set as the active key.

Input up to four keys for encryption. You will select one of these keys in the Key Index drop-down menu.

When you select either WPA-Personal or WPA-Enterprise, you must also choose a WPA mode from the drop-down menu: AUTO

(WPA or WPA2), WPA2 Only, or WPA Only. WPA and WPA2 use dierent algorithms. AUTO (WPA or WPA2) allows you to use both

WPA and WPA2. In addition, you must congure Cipher Type, and Group Key Update Interval.

Select Auto, AES, or TKIP from the drop-down menu.

Select the interval during which the group key will be valid. The default value of 1800 seconds is recommended.

When you select WPA-Personal, please enter a Pass Phrase in the corresponding eld.

When you select WPA-Personal, please re-enter the Pass Phrase entered in the previous item in the corresponding eld.

When you select WPA-Enterprise, enter the IP address of the RADIUS server. In addition, you must congure RADIUS Port and

RADIUS Secret.

Enter the RADIUS port.

Enter the RADIUS secret.

Web User Interface

VLAN

The DIS-2650AP supports VLANs. VLANs can be created with a Name and VID. Mgmt (TCP stack), LAN, Primary/Multiple SSID, and WDS connection

can be assigned to VLANs as they are physical ports. Any packet which enters the DIS-2650AP without a VLAN tag will have a VLAN tag inserted

with a PVID. The VLAN List tab displays the current VLANs.

VLAN Status:

VLAN Mode:

Use the radio button to toggle to Enable. Next,

go to the Add/Edit VLAN tab to add or modify

an item on the VLAN List tab.

The current VLAN mode is displayed.

VLAN List

Web User Interface

The Port List tab displays the current ports. If you want to congure the guest and internal networks on a Virtual LAN (VLAN), the switch and DHCP

server you are using must also support VLANs. As a prerequisite step, congure a port on the switch for handling VLAN tagged packets as described

in the IEEE 802.1Q standard.

VLAN Status:

Port Name:

Tag VID:

Untag VID:

PVID:

Use the radio button to toggle to Enable. Next, go to the Add/Edit

VLAN tab to add or modify an item on the VLAN List tab.

The name of the port is displayed in this column.

The Tagged VID is displayed in this column.

The Untagged VID is displayed in this column.

The Port VLAN Identier is displayed in this column.

Port List

Web User Interface

The Add/Edit VLAN tab is used to congure VLANs. Once you have made the desired changes, click Save to have your changes take eect.

VLAN Status:

VLAN ID:

VLAN Name:

Use the radio button to toggle to Enable.

Provide a number between 1 and 4094

for the Internal VLAN.

Enter the VLAN to add or modify.

Add/Edit VLAN

Web User Interface

The PVID Setting tab is used to enable/disable the Port VLAN Identier Auto Assign Status as well as to congure various types of PVID settings.

Click Save button to have your changes take eect.

VLAN Status:

PVID Auto Assign Status:

Use the radio button to toggle between

Enable and Disable.

Use the radio button to toggle PVID auto

assign status to Enable.

PVID Settings

Web User Interface

Intrusion

The Wireless Intrusion Protection window is used to classify APs as Valid, Neighborhood, Rogue, or a New group. Click Save for the changes to take

eect.

Wireless Band: Click the drop-down menu to select the wireless

band, 2.4GHz or 5GHz.

Detect: Click Detect to initiate a scan of the network.

AP List: Click the drop-down menu to select All, Valid,

Neighbor, Rogue, and New.

The following is a denition of the listed AP cat-

egories:

yValid: An AP which is authenticated to the net-

work with encryption is classied as valid.

yNeighbor: A detected AP with a weak signal

strength is classied as a suspect neighbor.

yRogue: An AP that has been installed on the

secure network without explicit authorization.

yNew: An alternative category.

From the AP List select a detected AP and click

Set as Valid, Set as Neighborhood, Set as Rogue,

or Set as New to manually dene the category

type for the AP. Alternatively, click the radio but-

ton to mark all new access points as valid or

rogue.

Web User Interface

Schedule

The Wireless Schedule Settings window is used to add and modify scheduling rules on the device. Click Save for your changes to take eect.

Wireless Schedule:

Name:

Index:

SSID:

Day(s):

All Day(s):

Start Time:

End Time:

Use the drop-down menu to enable the device’s

scheduling feature.

Enter a name for the new scheduling rule in the eld

provided.

Use the drop-down menu to select the desired SSID.

This read-only eld indicates the current SSID in use. To

create a new SSID, go to the Wireless Settings window

(Basic Settings > Wireless).

Toggle the radio button between All Week and Select

Day(s). If the second option is selected, check the

specic days you want the rule to be eective on.

Check this box to have your settings apply 24 hours

a day.

Enter the beginning hour and minute, using a 24-hour

clock.

Enter the ending hour and minute, using a 24-hour

clock.

Web User Interface

Internal RADIUS Server

The DIS-2650AP features a built-in RADIUS server. Once you have nished adding a RADIUS account, click the Save to have your changes take eect.

The newly-created account will appear in this RADIUS Account List. The radio buttons allow the user to enable or disable the RADIUS account. Click

the icon in the delete column to remove the RADIUS account. We suggest you limit the number of accounts to below 30.

User Name:

Password:

Status:

RADIUS Account List:

Enter a name to authenticate user access to the

internal RADIUS server.

Enter a password to authenticate user access to the

internal RADIUS server. The length of your password

should be 8~64.

Toggle the drop-down menu between Enable and

Disable.

Displays the list of users.

Web User Interface

ARP Spoong Prevention

The ARP Spoong Prevention feature allows users to add IP/MAC address mapping to prevent ARP Spoong attack.

ARP Spoong Prevention:

Gateway IP Address:

Gateway MAC Address:

This check box allows you to enable the ARP

Spoong prevention function.

Enter a gateway IP address.

Enter a gateway MAC address.

Web User Interface

Bandwidth Optimization

The Bandwidth Optimization window allows the user to manage the bandwidth of the device and arrange the bandwidth for various wireless clients.

When the Bandwidth Optimization rule is nished, click the Add button. To discard the Add Bandwidth Optimization Rule settings, click the Clear

button. Click Save button to have your changes take eect.

Enable Bandwidth

Optimization:

Downlink Bandwidth:

Uplink Bandwidth:

Allocate average BW

for each station:

Allocate maximum BW

for each station:

Allocate dierent BW

for a/b/g/n stations:

Allocate specic BW

for SSID:

Rule Type:

Use the drop-down menu to Enable the Bandwidth

Optimization function.

Enter the downlink bandwidth of the device in

Mbits per second.

Enter the uplink bandwidth of the device in Mbits

per second.

AP will distribute the average bandwidth for each

client.

Specify the maximum bandwidth for each

connected client. Reserve certain bandwidth for

future clients.

The weight of 11b/g/n and 11a/n client are

10%/20%/70% ; 20%/80%. AP will distribute

dierent bandwidth for 11a/b/g/n clients.

All clients share the total bandwidth.

Use the drop-down menu to select the type

that is applied to the rule. Available options are:

Allocate average BW for each station, Allocate

maximum BW for each station, Allocate

dierent BW for 1a/b/g/n stations, and Allocte

specic BW for SSID.

Web User Interface

Band:

SSID Index:

Downlink Speed:

Uplink Speed:

Use the drop-down menu to toggle the wireless band between 2.4GHz and 5GHz.

Use the drop-down menu to select the SSID for the specied wireless band.

Enter the download speed limit in either Kbits/sec or Mbits/sec for the rule.

Enter the upload speed limit in either Kbits/sec or Mbits/sec for the rule.

Web User Interface

Hotspot 2.0

Hotspot 2.0 (HS2) is a new networking standard designed to make the process of connecting to public wireless hotspots easier and more secure

with seamless authentication and encryption between your device and access points. This is based on the IEEE 802.11u standard and uses WPA2-

Enterprise for authentication between clients and access points.

Band: Specify Either 2.4 GHz or 5 GHz from the drop down list.

SSID Index: Specify from drop down list the SSID index.

Hotspot 2.0:

OSEN:

Allow Cross

Connection:

Manage P2P:

DGAF:

Proxy ARP:

L2TIF:

Choose enable to turn on hotspot 2.0 function.

Enable OSU Server-only authenticated layer-2

Encryption Network (OSEN) to indicate that the

hotspot uses a OSEN network type.

Choose enable to allow cross connection for

clients.

Choose enable to allow P2P.

This option congures the Downstream Group

Addressed Forwarding. Choose enable to

allow AP to forward downstream group-

addressed frames.

Choose enable to allow proxy ARP.

Choose enable to allow Layer 2 Traffic

Inspection and Filtering.

Hotspot

Web User Interface

Interworking:

Access Network Type:

Internet:

ASRA:

ESR:

Venue Group:

Venue Type:

Venue Name:

HESSID:

Choose enable to turn on interworking

function.

Specify type of network.

Choose to enable or disable Internet access for

this network.

Choose enable if the network has Additional

Steps required for Access.

Choose enable to indicate that emergency

services are reachable through this device.

Specify group venue belongs to.

Specify type of venue.

Specify name of venue. Choose from the drop

down list a language used in the name.

Specify a homogenous extended service set

(ESS) ID that can be used to identify a specic

service provider network.

Interworking

Web User Interface

WAN Link Status:

WAN Symmetric Link:

WAN At Capacity:

WAN Metrics DL Speed:

WAN Metrics UL Speed:

Information about the status of the Access

Point’s WAN connection.

Set to 1 if the WAN link is symmetric (upload

and download speeds are the same), or set to

0 if not.

Set to 1 if the Access Point or the network is at

its max capacity, or set to 0 if not.

The downlink speed of the WAN connection

set in kbps. If the downlink speed is not known,

set to 0.

The uplink speed of the WAN connection set in

kbps. If the uplink speed is not known set to 0.

WAN Metrics

Web User Interface

Network Auth Type:

IP Address Type

Avilability:

Domain Name List:

Roaming Consortium:

Nai Realm List:

3gpp Cellular Network:

Connection Capability:

Operator Friendly

Name:

QoS Map:

Identies whether this is an unsecured network.

Identifies IP address version and type that

the Hotspot Operator uses and that would be

allocated and available to a mobile device after

it authenticates to the network.

List one or more domain names for the entity

operating the AP.

Identifies service providers or groups of

roaming partners whose security credentials

can be used to connect to a network.

List of all NAI realms available through the BSS.

Identies the 3GPP cellular networks available

through the AP.

Identifies the availability of common IP

protocols (TCP, UDP, IPsec) and ports (21, 80,

443, 5060).

Identies the Hotspot venue operator.

Bit set to indicate support for QoS mapping

from 802.11 to external networks.

LIST

Web User Interface

OSU SSID:

OSU Server URI:

OSU Method List:

OSU Cong:

OSU language:

OSU Friendly Name:

OSU Nai:

OSU Service

Description:

OSU Icon Language:

Specify the SSID that the device will associate

and connect to when accessing the

OSU server.

Specify the Uniform Resource Identier (URI)

of the OSU Server.

Spcify preferred list of encoding methods that

the OSU server supports in order of priority.

Choose from drop down list which conguration

set to use.

Choose from drop down list language to use.

Specify a list of one or more names in dierent

languages which will allow the device to

display the OSU Friendly Name in alternative

languages based on the language slected in

the setting of the mobile device.

Specify OSU Network Access Identier.

Choose the service description lagnuage from

drop down list. Specify the service provider’s

descrption of service oering.

Choose icon language from drop down list.

OSU

Web User Interface

OSU Icon Name:

OSU Icon Width:

OSU Icon Height:

OSU Icon Type:

OSU Icon File Path:

Specify icon name.

Specify width of the icon, in pixels.

Spcify length of the icon, in pixels.

Speciy icon le type, where the icon type is any mim-type

graphic format.

Specify location of icon le.

Web User Interface

Captive Portal

The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web browser will be redirected to a web authentication

page. In this window, user can view and congure the Captive Portal settings. After selecting Web Redirection Only as the Authentication Type, we

can congure the redirection website URL that will be applied to each wireless client in this network.

Authentication Settings-Web Redirection Only

Session

timeout(1-1440) :

Band :

SSID Index :

Authentication Type :

Web Redirection State :

URL Path :

IPIF Status :

VLAN Group :

Get IP From :

Enter the session timeout value here. This value can be from 1 to 1440 minutes. By default, this value is 60 minutes.

Select 2.4GHz or 5GHz.

Select the SSID for this Authentication.

Select the captive portal encryption type here.

Options to choose from are Web Redirection,

Username/Password, Passcode, Remote

RADIUS, LDAP and POP3. In this section we’ll

discuss the Web Redirection option.

Default setting is Enable when select Web

Redirection Only.

Select whether to use either HTTP or HTTPS

here. After selecting either http:// or https://,

enter the URL of the website that will be used

in the space provided.

Select to Enable or Disable the Captive Portal

with its IP interface feature here.

Enter the VLAN Group ID here.

Static IP (Manual) is chosen here. Choose this option if you do not have a DHCP server in your network, or if you wish to

assign a static IP address to the DIS-2650AP. When Dynamic IP (DHCP) is selected, the other elds here will be grayed out.

Please allow about 2 minutes for the DHCP client to be functional once this selection is made.

Web User Interface

IP Address :

Subnet Mask :

Gateway :

DNS :

Assign a static IP address that is within the IP address range of your network.

Enter the subnet mask. All devices in the network must share the same subnet mask.

Enter the IP address of the gateway/router in your network.

Enter a DNS server IP address. This is usually the local IP address of your gateway/router.

Web User Interface

After selecting Username/Password as the Authentication Type, we can congure the Username/Password authentication that will be applied to

each wireless client in this network.

Authentication Settings- Username/Password

Session

timeout(1-1440) :

Band :

SSID Index :

Authentication Type :

Web Redirection State :

URL Path :

IPIF Status :

VLAN Group :

Get IP From :

Enter the session timeout value here. This value

can be from 1 to 1440 minutes. By default, this

value is 60 minutes.

Select 2.4GHz or 5GHz.

Select the SSID for this Authentication.

Select the captive portal encryption type here.

Options to choose from are Web Redirection,

Username/Password, Passcode, Remote

RADIUS, LDAP and POP3. In this section we’ll

discuss the Username/Password option.

Default is Disable or select Enable to enable the

website redirection feature.

Select whether to use either HTTP or HTTPS

here. After selecting either http:// or https://,

enter the URL of the website that will be used

in the space provided.

Select to Enable or Disable the Captive Portal

with its IP interface feature here.

Enter the VLAN Group ID here.

Static IP (Manual) is chosen here. Choose this

option if you do not have a DHCP server in

your network, or if you wish to assign a static

IP address to the DIS-2650AP. When Dynamic

Web User Interface

IP Address :

Subnet Mask :

Gateway :

DNS :

Username:

Password:

IP (DHCP) is selected, the other elds here will be grayed out. Please allow about 2 minutes for the DHCP client to be

functional once this selection is made.

Assign a static IP address that is within the IP address range of your network.

Enter the subnet mask. All devices in the network must share the same subnet mask.

Enter the IP address of the gateway/router in your network.

Enter a DNS server IP address. This is usually the local IP address of your gateway/router.

Enter the username for the new account here.

Enter the password for the new account here.

Web User Interface

After selecting Passcode as the Authentication Type, we can congure the Passcode authentication that will be applied to each wireless client in

this network.

Authentication Settings- Passcode

Session

timeout(1-1440) :

Band :

SSID Index :

Authentication Type :

Web Redirection State :

URL Path :

IPIF Status :

VLAN Group :

Get IP From :

Enter the session timeout value here. This value

can be from 1 to 1440 minutes. By default, this

value is 60 minutes.

Select 2.4GHz or 5GHz.

Select the SSID for this Authentication.

Select the captive portal encryption type here.

Options to choose from are Web Redirection,

Username/Password, Passcode, Remote

RADIUS, LDAP and POP3. In this section we’ll

discuss the Passcode option.

Default is Disable or select Enable to enable the

website redirection feature.

Select whether to use either HTTP or HTTPS

here. After selecting either http:// or https://,

enter the URL of the website that will be used

in the space provided.

Select to Enable or Disable the Captive Portal

with its IP interface feature here.

Enter the VLAN Group ID here

Static IP (Manual) is chosen here. Choose this

option if you do not have a DHCP server in

your network, or if you wish to assign a static

IP address to the DIS-2650AP. When Dynamic IP

(DHCP) is selected, the other elds here will be

Web User Interface

IP Address :

Subnet Mask :

Gateway :

DNS :

Passcode Quantity:

Duration:

Last Active Day:

User Limit:

grayed out. Please allow about 2 minutes for the DHCP client to be functional once this selection is made.

Assign a static IP address that is within the IP address range of your network.

Enter the subnet mask. All devices in the network must share the same subnet mask.

Enter the IP address of the gateway/router in your network.

Enter a DNS server IP address. This is usually the local IP address of your gateway/router.

Enter the number of ticket that will be used here.

Enter the duration value, in hours, for this passcode.

Select the last active date for this passcode here. Year, Month and Day selections can be made.

Enter the maximum amount of users that can use this passcode at the same time

Web User Interface

After selecting Remote RADIUS as the Authentication Type, we can congure the Remote RADIUS authentication that will be applied to each

wireless client in this network.

Authentication Settings- Remote RADIUS

Session

timeout(1-1440) :

Band :

SSID Index :

Authentication Type :

Web Redirection State :

URL Path :

IPIF Status :

VLAN Group :

Get IP From :

Enter the session timeout value here. This value can

be from 1 to 1440 minutes. By default, this value is 60

minutes.

Select 2.4GHz or 5GHz.

Select the SSID for this Authentication.

Select the captive portal encryption type here. Options

to choose from are Web Redirection, Username/

Password, Passcode, Remote RADIUS, LDAP and POP3.

In this section we’ll discuss the Remote RADIUS option.

Default is Disable or select Enable to enable the

website redirection feature.

Select whether to use either HTTP or HTTPS here. After

selecting either http:// or https://, enter the URL of the

website that will be used in the space provided.

Select to Enable or Disable the Captive Portal with its

IP interface feature here.

Enter the VLAN Group ID here

Static IP (Manual) is chosen here. Choose this option if

you do not have a DHCP server in your network, or if

you wish to assign a static IP address to the DIS-2650AP.

When Dynamic IP (DHCP) is selected, the other elds

here will be grayed out. Please allow about 2 minutes

for the DHCP client to be functional once this selection

is made.

Web User Interface

IP Address :

Subnet Mask :

Gateway :

DNS :

Radius Server:

Radius Port:

Remote Radius Type:

Assign a static IP address that is within the IP address range of your network.

Enter the subnet mask. All devices in the network must share the same subnet mask.

Enter the IP address of the gateway/router in your network.

Enter a DNS server IP address. This is usually the local IP address of your gateway/router.

Enter the RADIUS server’s IP address here

Enter the RADIUS server’s port number here

Enter the RADIUS server’s shared secret here

Select the remote RADIUS server type here. Currently, only SPAP will be used.

Web User Interface

After selecting LDAP as the Authentication Type, we can congure the LDAP authentication that will be applied to each wireless client in this network.

Authentication Settings- LDAP

Session

timeout(1-1440) :

Band :

SSID Index :

Authentication Type :

Web Redirection State :

URL Path :

IPIF Status :

VLAN Group :

Get IP From :

IP Address :

Enter the session timeout value here. This value can

be from 1 to 1440 minutes. By default, this value is

60 minutes.

Select 2.4GHz or 5GHz.

Select the SSID for this Authentication.

Select the captive portal encryption type here.

Options to choose from are Web Redirection,

Username/Password, Passcode, Remote RADIUS,

LDAP and POP3. In this section we’ll discuss the LDAP

option.

Default is Disable or select Enable to enable the

website redirection feature.

Select whether to use either HTTP or HTTPS here.

After selecting either http:// or https://, enter the URL

of the website that will be used in the space provided.

Select to Enable or Disable the Captive Portal with

its IP interface feature here.

Enter the VLAN Group ID here.

Static IP (Manual) is chosen here. Choose this option

if you do not have a DHCP server in your network,

or if you wish to assign a static IP address to the

DIS-2650AP. When Dynamic IP (DHCP) is selected,

the other elds here will be grayed out. Please allow

about 2 minutes for the DHCP client to be functional

once this selection is made.

Assign a static IP address that is within the IP address

range of your network.

Web User Interface

Subnet Mask :

Gateway :

DNS :

Server:

Port:

Authenticate Mode:

Username:

Password:

Base DN:

Account Attribute:

Identity:

Enter the subnet mask. All devices in the network must share the same subnet mask.

Enter the IP address of the gateway/router in your network.

Enter a DNS server IP address. This is usually the local IP address of your gateway/router.

Enter the LDAP server’s IP address or domain name here.

Enter the LDAP server’s port number here.

Select the authentication mode here. Options to choose from are Simple and TLS.

Enter the LDAP server account’s username here.

Enter the LDAP server account’s password here.

Enter the administrator’s domain name here.

Enter the LDAP account attribute string here.

This string will be used to search for clients.

Enter the identity’s full path string here. Alternatively, select the Auto Copy checkbox to automatically add the generic full

path of the web page in the identity eld.

Web User Interface

After selecting POP3 as the Authentication Type, we can congure the POP3 authentication that will be applied to each wireless client in this network.

Authentication Settings- POP3

Session

timeout(1-1440) :

Band :

SSID Index :

Authentication Type :

Web Redirection State :

URL Path :

IPIF Status :

VLAN Group :

Get IP From :

Enter the session timeout value here. This value

can be from 1 to 1440 minutes. By default, this

value is 60 minutes.

Select 2.4GHz or 5GHz.

Select the SSID for this Authentication.

Select the captive portal encryption type here.

Options to choose from are Web Redirection,

Username/Password, Passcode, Remote

RADIUS, LDAP and POP3. In this section we’ll

discuss the POP3 option.

Default is Disable or select Enable to enable the

website redirection feature.

Select whether to use either HTTP or HTTPS

here. After selecting either http:// or https://,

enter the URL of the website that will be used

in the space provided.

Select to Enable or Disable the Captive Portal

with its IP interface feature here.

Enter the VLAN Group ID here.

Static IP (Manual) is chosen here. Choose this

option if you do not have a DHCP server in

your network, or if you wish to assign a static

IP address to the DIS-2650AP. When Dynamic IP

Web User Interface

IP Address :

Subnet Mask :

Gateway :

DNS :

Server:

Port:

Connection Type:

(DHCP) is selected, the other elds here will be grayed out. Please allow about 2 minutes for the DHCP client to be functional

once this selection is made.

Assign a static IP address that is within the IP address range of your network.

Enter the subnet mask. All devices in the network must share the same subnet mask.

Enter the IP address of the gateway/router in your network.

Enter a DNS server IP address. This is usually the local IP address of your gateway/router.

Enter the POP3 server’s IP address or domain name here.

Enter the POP server’s port number here.

Select the connection type here. Options to choose from are None and SSL/TLS.

Web User Interface

In this window, users can upload a custom login web page that will be used by the captive portal feature. Click the Browse button to navigate to

the login style, located on the managing computer and then click the Upload button to initiate the upload.

Upload Login Style

From Local Hard Drive:

In this eld the path to the login style le that will

be uploaded, will be displayed. Alternatively, the

path can be manually entered here.

Select the wireless band and login style that will

be used in each SSID here. Click Download button

to download the template le for login page and

Click Del button to delete the template le.

Web User Interface

MAC Bypass

The DIS-2650AP features a wireless MAC Bypass. Once a user is nished with these settings, click Save for changes to take eect.

Wireless Band:

SSID Index:

MAC Address:

MAC Address List:

Upload File:

Load MAC File to Local

Hard Driver:

Select the wireless band for MAC Bypass.

Select the SSID for MAC Bypass.

Enter each MAC address that you wish to include

in your bypass list, and click Add.

When a MAC address is entered, it appears in

this list.

Highlight a MAC address and click the Delete

icon to remove it from this list.

To upload a MAC bypass list le, click Browse and

navigate to the MAC bypass list le saved on the

computer, and then click Upload.

To download MAC bypass list le, click Download

and to save the MAC bypass list.

Web User Interface

DHCP Server

The DHCP address pool denes the range of the IP address that can be assigned to stations in the network. A Dynamic Pool allows wireless stations

to receive an available IP with lease time control. If needed or required in the network, the DIS-2650AP is capable of acting as a DHCP server.

Function Enable/Disable:

IP Assigned From:

The Range of Pool (1-254):

Subnet Mask:

Gateway:

WINS:

DNS:

Domain Name:

Lease Time:

Dynamic Host Configuration Protocol (DHCP) assigns

dynamic IP addresses to devices on the network. This protocol

simplies network management and allows new wireless

devices to receive IP addresses automatically without the

need to manually assign new IP addresses. Select Enable to

allow the DIS-2650AP to function as a DHCP server.

Input the rst IP address available for assignment on your

network.

Enter the number of IP addresses available for assignment.

IP addresses are increments of the IP address specied in the

“IP Assigned From” eld.

Dynamic Pool Settings

All devices in the network must have the same subnet

mask to communicate. Enter the subnet mask for the

network here.

Enter the IP address of the gateway on the network.

Specify the Windows Internet Naming Service (WINS) server address for the wireless network. WINS is a system that

determines the IP address of a network computer that has a dynamically assigned IP address.

Enter the IP address of the Domain Name System (DNS) server. The DNS server translates domain names such as

www.dlink.com into IP addresses.

Enter the domain name of the network, if applicable. (An example of a domain name is: www.dlink.com.)

The lease time is the period of time before the DHCP server will assign new IP addresses.

Web User Interface

Static Pool Setting

The DHCP address pool denes the range of IP addresses that can be assigned to stations on the network. A static pool allows specic wireless

stations to receive a xed IP without time control.

Function Enable/Disable:

Assigned IP:

Assigned MAC Address:

Subnet Mask:

Gateway:

WINS:

DNS:

Domain Name:

Dynamic Host Configuration Protocol (DHCP)

assigns IP addresses to wireless devices on

the network. This protocol simplifies network

management and allows new wireless devices

to receive IP addresses automatically without

the need to manually assign IP addresses. Select

Enable to allow the DIS-2650AP to function as a

DHCP server.

Use the Static Pool Settings to assign the same IP

address to a device every time you start up. The

IP addresses assigned in the Static Pool list must

NOT be in the same IP range as the Dynamic

Pool. After you have assigned a static IP address

to a device via its MAC address, click Apply; the

device will appear in the Assigned Static Pool at

the bottom of the screen. You can edit or delete

the device in this list.

Enter the MAC address of the device requesting

association here.

Dene the subnet mask of the IP address specied

in the “IP Assigned From” eld.

Specify the Gateway address for the wireless network.

Specify the Windows Internet Naming Service (WINS) server address for the wireless network. WINS is a system that

determines the IP address of a network computer with a dynamically assigned IP address, if applicable.

Enter the DNS server address for your wireless network.

Specify the domain name for the network.

Web User Interface

Current IP Mapping List

This window displays information about the current assigned DHCP dynamic and static IP address pools. This information is available when you

enable DHCP server on the AP and assign dynamic and static IP address pools.

Current DHCP Dynamic

Prole:

Binding MAC Address:

Assigned IP Address:

Lease Time:

Current DHCP Static Pools:

Binding MAC Address:

Assigned IP Address:

Binding MAC Address:

Assigned IP Address:

These are IP address pools the DHCP server has

assigned using the dynamic pool setting.

The MAC address of a device on the network

that is assigned an IP address from the DHCP

dynamic pool.

The current corresponding DHCP-assigned IP

address of the device.

The length of time that the dynamic IP address

will be valid.

These are the IP address pools of the DHCP

server assigned through the static pool settings.

The MAC address of a device on the network

that is within the DHCP static IP address pool.

The current corresponding DHCP-assigned

static IP address of the device.

The MAC address of a device on the network

that is assigned an IP address from the DHCP

dynamic pool.

The current corresponding DHCP-assigned

static IP address of the device.

Web User Interface

Filters

This page allows the user to congure Wireless MAC ACL settings for access control.

Wireless Band:

Access Control List:

MAC Address:

MAC Address List:

Current Client

Information:

Upload ACL File:

Download ACL File:

Displays the current wireless band rate.

Select Disable to disable the lters function.

Select Accept to accept only those devices with MAC

addresses in the Access Control List. All other devices

not on the list will be rejected.

Select Reject to reject the devices with MAC

addresses on the Access Control List. All other devices

not on the list will be accepted.

Enter each MAC address that you wish to include in

your lter list, and click Apply.

When you enter a MAC address, it appears in this list.

Highlight a MAC address and click Delete to remove

it from this list.

This table displays information about all the current

connected stations.

Upload the user’s own ACL File here.

Download currenty ACL list to local hard drive.

Wireless MAC ACL

Web User Interface

Enter the IP address or network address that will be used in the IP lter rule. For example, an IP address like 192.168.70.66 or a network address

like 192.168.70.0. This IP address or network will be inaccessible to wireless clients in this network.

IP Filter Settings

Wireless Band: Click the drop-down menu to select the

wireless band, 2.4GHz or 5GHz.

SSID Index: Click the drop-down menu to select the SSID

for the IP lter.

Filter State: Click the drop-down menu to enable or

disable the lter state. By default this feature

is disabled.

IP Address: Enter the IP address or network address.

Subnet Mask: Enter the subnet mask of the IP address or

networks address.

IP Address List: When an IP address is entered, it appears in

the list.

Highlight a IP address and click Delete icon

to remove it from the list.

Upload IP Filter File: To upload a IP lter list le, click Choose File

and navigate to the IP lter list le saved on

the computer, and then click Upload.

Download IP Filter File: To download IP Filter list le, click Download

and to save the IP lter list.

Web User Interface

This page allows the user to congure a WLAN Partition.

Wireless Band:

Link Integrity:

Ethernet WLAN Access:

Internal Station

Connection:

Displays the current wireless band.

Select Enable or Disable. If the Ethernet

connection between the LAN and the AP is

disconnected, enabling this feature will cause

the wireless segment associated with the AP to

be disassociated from the AP.

The default is Enable. When disabled, all data

from the Ethernet to associated wireless devices

will be blocked. Wireless devices can still send

data to the Ethernet.

The default value is Enable, which allows stations

to intercommunicate by connecting to a target

AP. When disabled, wireless stations cannot

exchange data on the same Multi-SSID. In Guest

mode, wireless stations cannot exchange data

with any station on your network.

WLAN Partition

Web User Interface

Trac Control

The uplink/downlink setting allows users to customize the downlink and uplink interfaces including specifying downlink/uplink bandwidth rates in

Mbits per second. These values are also used in the QoS and Trac Manager windows. Once the desired uplink and downlink settings are nished,

click the Save button to have your changes take eect.

Downlink Bandwidth:

Uplink Bandwidth:

The downlink bandwidth in Mbits per second.

The uplink bandwidth in Mbits per second.

Uplink/Downlink Setting

Web User Interface

Quality of Service (QoS) enhances the experience of using a network by prioritizing the trac of dierent applications. The DIS-2650AP supports

four priority levels. Once the desired QoS settings are nished, click the Save to have your changes take eect.

Enable QoS:

Downlink Bandwidth:

Uplink Bandwidth:

Check this box to allow QoS to prioritize trac.

Use the drop-down menus to select the four

levels of priority. Click the Save button when

you are nished.

Downlink Bandwidth: The downlink bandwidth

in Mbits per second. This value is entered in the

Uplink/Downlink Setting window.

Uplink Bandwidth: The uplink bandwidth in

Mbits per second. This value is entered in the

Uplink/Downlink Setting window.

QoS

Web User Interface

The trac manager feature allows users to create trac management rules that specify how to deal with listed client trac and specify downlink/

uplink speed for new trac manager rules. Click the Save to have your changes take eect.

Trac Manager:

Unlisted Client Trac:

Downlink Bandwidth:

Uplink Bandwidth:

Name:

Client IP (optional):

Client MAC (optional):

Downlink Speed:

Uplink Speed:

Use the drop-down menu to Enable the

trac manager feature.

Select Deny or Forward to determine how

to deal with unlisted client trac.

The downlink bandwidth in Mbits per

second. This value is entered in the Uplink/

Downlink Setting window.

The uplink bandwidth in Mbits per second.

This value is entered in the Uplink/Downlink

Setting window.

Enter the name of the trac manager rule.

Enter the client IP address of the trac

manager rule.

Enter the client MAC address of the trac

manager rule.

Enter the downlink speed in Mbits per

second.

Enter the uplink speed in Mbits per second.

Trac Manager

Web User Interface

Status

In the Status Section the user can monitor and view conguration settings of the access point. Here the user can also view statistics about client

information, WDS information and more. The following pages will explain settings found in the Status section in more detail.

Web User Interface

Device Information

This page displays the current information like rmware version, Ethernet and wireless parameters, as well as the information regarding CPU and

memory utilization.

Device Information: This read-only window displays the

conguration settings of the DIS-2650AP,

including the firmware version and the

device’s MAC address.

Web User Interface

Client Information

This page displays the associated clients SSID, MAC, band, authentication method, signal strength, RSSI, and power saving mode for the DIS-2650AP

network.

Client Information:

SSID:

MAC:

Band:

Authentication:

RSSI:

Power Saving Mode:

This window displays the wireless client

information for clients currently connected

to the DIS-2650AP.

Displays the SSID of the client.

Displays the MAC address of the client.

Displays the wireless band that the client is

connected to.

Displays the type of authentication being

used.

Displays the client’s signal strength.

Displays the status of the power saving

feature.

Web User Interface

WDS Information Page

This page displays the access points SSID, MAC, band, authentication method, signal strength, and status for the DIS-2650AP’s Wireless Distribution

System network.

WDS Information:

Name:

MAC:

Authentication:

Signal:

Status:

This window displays the Wireless Distribution

System information for clients currently

connected to the DIS-2650AP.

Displays the SSID of the client.

Displays the MAC address of the client.

Displays the type of authentication being

used.

Displays the client’s signal strength.

Displays the status of the power saving

feature.

Web User Interface

Statistics

Displays wired interface network trac information.

Ethernet Trac Statistics: This page displays transmitted and received

count statistics for packets and bytes.

Ethernet Trac Statistics

Web User Interface

WLAN Trac Statistics

Displays throughput, transmitted frame, received frame, and WEP frame error information for the AP network.

WLAN Trac Statistics: This page displays wireless network

statistics for data throughput,

transmitted and received frames, and

frame errors.

Web User Interface

Log

The AP’s embedded memory holds logs here. The log information includes but is not limited to the following items: cold start AP, upgrading rmware,

client associate and disassociate with AP, and web login. The web page holds up to 500 logs.

View Log: The AP’s embedded memory displays

system and network messages including

a time stamp and message type. The log

information includes but is not limited

to the following items: cold start AP,

upgrading rmware, client associate and

disassociate with AP, and web login. The

web page holds up to 500 logs.

View Log

Web User Interface

Log Settings

Enter the log server’s IP address to send the log to that server. Check or uncheck System Activity, Wireless Activity, or Notice to specify what kind

of log type you want it to log.

Log Server / IP Address: Enter the IP address of the log server.

Log Type: Check the boxes to select the log type.

Log Server / IP Address: Enter the IP address of the EU directive Syslog

server.

Email Notication: Check the box to enable sending email

notication.

Outgoing mail server

(SMTP):

Click the drop-down menu to select the SMTP

server type, options include: Internal, Gmail,

Hotmail.

Authentication: Check the box to enable the authentication

of the email notication.

SSL/TLS: Check the box to enable the SSL/TLS function.

From Email Address: Enter the email address.

To Email Address: Enter the email address.

Email Server Address: Enter the email server address.

SMTP Port: Enter the SMTP port.

User Name: Enter the name of the new user entry.

Password: Enter the password set for the email

notication.

Conrm Password: Retype the password entry to conrm the

password.

Schedule: Click the drop-down menu to set email log

schedule.

Web User Interface

Maintenance Section

In the Status Section the user can monitor and view conguration settings of the access point. Here the user can also view statistics about client

information, WDS information and more. The following pages will explain settings found in the maintenance section in more detail.

Web User Interface

Administration

Check one or more of the ve main categories to display the various hidden administrator parameters and settings displayed on the next ve pages.

Each of the nine main categories display various hidden administrator parameters and settings. Click Save when done.

Limit Administrator VLAN

ID:

Limit Administrator IP:

IP Range:

Check the box provided and the enter the

specic VLAN ID that the administrator will

be allowed to log in from.

Check to enable the Limit Administrator

IP address.

Enter the IP address range that the

administrator will be allowed to log in

from and then click the Add button.

Limit Administrator

Web User Interface

System Name Settings

Each of the ve main categories display various hidden administrator parameters and settings.

System Name:

Location:

MDNS Name:

The name of the device. The default

name is D-Link DIS-2650AP.

The physical location of the device, e.g.

72nd Floor, D-Link HQ.

Enter the name of the multicast DNS. The

default name is dis2650ap.

Each of the ve main categories display various hidden administrator parameters and settings.

User Name:

Old Password:

New Password:

Conrm Password:

Enter a user name. The default is admin.

When changing your password, enter the

old password here.

When changing your password, enter

the new password here. The password is

case-sensitive. “A” is a dierent character

than “a.” The length should be between

0 and 12 characters.

Enter the new password a second time

for conrmation purposes.

Web User Interface

Ping Control Settings

Choose to enable or disable ping function.

Enable: Click to disable. (By default it is enabled.)

LED Settings

Choose to enable or disable LED status.

LED Status: Choose corresponding radio button to

enable or disable LED Status.

Country Settings

Select your country.

Select a Country: Choose from the drop down list the

country your device is located.

Console Settings

Each of the ve main categories display various hidden administrator parameters and settings.

Status:

Console Protocol:

Time-out:

Status is enabled by default. Uncheck the

box to disable the console.

Select the type of protocol you would

like to use, Telnet or SSH.

Set to 1 Min, 3 Mins, 5 Mins, 10 Mins, 15

Mins or Never.

Web User Interface

Nuclias Connect Settings

Choose to enable or disable Nuclias Connect.

Enable Nuclias Connect: Choose from drop down list to enable or

disable Nuclias Connect.

DDP Settings

Choose to enable or disable DDP.

Status: Click to disable. (By default it is enabled.)

Web User Interface

Firmware and SSL Upload

This page allows the user to perform a rmware upgrade. A Firmware upgrade is a function that upgrade the running software used by the access

point. This is a useful feature that prevents future bugs and allows for new features to be added to this product. Please go to your local D-Link

website to see if there is a newer version of the rmware available.

Upload Firmware from

Local Hard Drive:

Language Pack Upgrade:

Upload SSL Certication

from Local Hard Drive:

The current rmware version is displayed

above the le location eld. After the

latest rmware is downloaded, click on

the “Choose File” button to locate the

new rmware. Once the le is selected,

click on the “Open” and “Update” button

to begin updating the rmware. Please

don’t turn the power o while upgrading.

You can upload an updated language

pack from the device here. Click on the

“Choose File” button to locate the new

language pack. Once the le is selected,

click on the “Open” and “Update” button

to being updating the language les.

After you have downloaded a SSL

certication to your local drive, click

“Choose File.” Select the certication and

click “Open” and “Upload” to complete

the upgrade. You can upload a SSL Key

in the same way.

Web User Interface

Conguration File Upload

This page allows the user to backup and recover the current conguration of the access point in case of a unit failure.

Conguration File Upload

and Download:

Upload Conguration File:

Download Conguration

File:

Upload Nuclias Connect

Network File:

You can upload and download

conguration les of the access point.

Browse to the saved conguration

le you have in local drive and click

“Open” and “Upload” to update the

conguration.

Click “Download” to save the current

conguration le to your local disk. Note

that if you save one conguration le

with the administrator’s password now,

after resetting your DIS-2650AP and then

updating to this saved conguration le,

the password will be gone.

Browse to the saved conguration le

you have in local drive and click “Open”

and “Upload” to update the Nuclias

Connect Network le.

Web User Interface

Time and Date Settings

Enter the NTP server IP, choose the time zone, and enable or disable daylight saving time.

Current Time:

Enable NTP Server:

NTP Server:

Time Zone:

Enable Daylight

Saving:

Daylight Saving

Dates:

Set the Date and

Time Manually:

Displays the current time and date settings.

Check to enable the AP to get system time

from an NTP server from the Internet.

Enter the NTP server IP address.

Use the drop-down menu to select your

correct Time Zone.

Check the box to enable Daylight Saving

Time.

Use the drop-down menu to select the

correct Daylight Saving oset.

A user can either manually set the time

for the AP here, or click the Copy Your

Computer’s Time Settings button to copy

the time from the computer in use (Make

sure that the computer’s time is set correctly).

Web User Interface

Conguration and System

These options are the remaining option to choose from in the top menu. Conguration allows the user to save and activate or discard the congurations

done. System allows the user to restart the unit, perform a factory reset or clear the language pack settings. Logout allows the user to safely log

out from the access point’s web conguration. Help allows the user to read more about the given options to congure without the need to consult

the manual. The following pages will explain settings found in the conguration and system section in more detail.

Web User Interface

System Settings

On this page the user can restart the unit, perform a factory reset of the access point or clear the added language pack.

Restart the Device:

Restore to Factory Default

Settings:

Clear Language Pack:

Click Restart to restart the DIS-2650AP.

Click Restore to restore the DIS-2650AP

back to factory default settings.

Click to clear the current Language pack

running.

Web User Interface

Help

The help page is useful to view a brief description of a function available on the access point in case the manual is not present.

Help: Scroll down the Help page for topics and

explanations.

Knowledge Base

D-Link wireless products are based on industry standards to provide high-speed wireless connectivity that is easy to use within your home,

business or public access wireless networks. D-Link wireless products provides you with access to the data you want, whenever and wherever

you want it. Enjoy the freedom that wireless networking can bring to you.

WLAN use is not only increasing in both home and oce environments, but in public areas as well, such as airports, coee shops and universities.

Innovative ways to utilize WLAN technology are allowing people to work and communicate more eciently. Increased mobility and the absence

of cabling and other types of xed infrastructure have proven to be benecial to many users.

Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards, allowing wireless users to use

the same applications as those used on a wired network.

People use WLAN technology for many dierent purposes:

• Mobility - productivity increases when people can have access to data in any location within the operating range of their WLAN.

Management decisions based on real-time information can signicantly improve the eciency of a worker.

• Low implementation costs - WLANs are easy to set up, manage, change and relocate. Networks that frequently change can benet from

WLAN’s ease of implementation. WLANs can operate in locations where installation of wiring may be impractical.

• Installation and network expansion - by avoiding the complications of troublesome cables, a WLAN system can be fast and easy during

installation, especially since it can eliminate the need to pull cable through walls and ceilings. Wireless technology provides more versatility

by extending the network beyond the home or oce.

• Inexpensive solution - wireless network devices are as competitively priced as conventional Ethernet network devices. The DIS-2650AP saves

money by providing users with multi-functionality congurable in four dierent modes.

• Scalability - Congurations can be easily changed and range from Peer-to-Peer networks, suitable for a small number of users to larger

Infrastructure networks to accommodate hundreds or thousands of users, depending on the number of wireless devices deployed.

Wireless Basics

Knowledge Base

The D-Link Access Point lets you access your network using a wireless connection from virtually anywhere within the operating range of your

wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must

pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your

home or business. The key to maximizing wireless range is to follow these basic guidelines:

1. Keep the number of walls and ceilings between the access point and other network devices to a minimum. Each wall or ceiling can reduce

your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is minimized.

2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a

3. 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so

that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception.

4. Building Materials make a dierence. A solid metal door or aluminum studs may have a negative eect on the range. Try to position access

points, wireless routers, and computers so that the signal passes through drywall or open doorways. Materials and objects such as glass,

steel, metal, walls with insulation, water (sh tanks), mirrors, le cabinets, brick, and concrete will degrade your wireless signal.

5. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF noise.

6. If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security systems), your wireless

connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone base is as far away from your wireless devices as

possible. The base transmits a signal even if the phone in not in use.

Wireless Installation Considerations

Troubleshooting

When entering the IP address of the D-Link access point (192.168.0.50 for example), you are not connecting to a website on the Internet or have to

be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to

connect to the web-based utility.

• Make sure you have an updated Java-enabled web browser. We recommend the following:

• Internet Explorer 7.0 or higher, Chrome, Firefox, or Safari 4 or higher

• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a dierent cable or connect to a

dierent port on the device if possible. If the computer is turned o, the link light may not be on.

• Disable any internet security software running on the computer. Software rewalls such as Zone Alarm, Black Ice, Sygate, Norton Personal Firewall, and

Windows® rewall may block access to the conguration pages. Check the help les included with your rewall software for more information on disabling

or conguring it.

• Congure your Internet settings:

Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their

defaults.

Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK.

Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.

Close your web browser (if open) and open it.

• Access the web management. Open your web browser and enter the IP address of your D-Link access point in the address bar. This should open the login

page for your the web management.

• If you still cannot access the conguration, unplug the power to the access point for 10 seconds and plug back in. Wait about 30 seconds and try accessing

the conguration. If you have multiple computers, try connecting using a dierent computer.

Why can’t I access the web-based conguration utility?

This chapter provides solutions to problems that can occur during the installation and operation of the DIS-2650AP. Read the following

descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a dierent operating system, the

screenshots on your computer will look similar to the following examples.)

If you forgot your password, you must reset your access point. Unfortunately, this process will change all your settings back to the factory defaults.

To reset the access point, locate the reset button (hole) on the rear panel of the unit. With the access point powered on, use a paperclip to hold the

button down for 10 seconds. Release the button and the access point will go through its reboot process. Wait about 30 seconds to access the access

point. The default IP address is 192.168.0.50. When logging in, the username is admin and leave the password box empty.

What can I do if I forgot my password?

Troubleshooting

After you install your network adapter, by default, the TCP/IP settings

should be set to obtain an IP address from a DHCP server (i.e. wireless

router) automatically. To verify your IP address, please follow the steps

below.

Click on Start > Run. In the run box type cmd and click OK.

At the prompt, type ipcong and press Enter.

This will display the IP address, subnet mask, and the default gateway of

your adapter.

If the address is 0.0.0.0, check your adapter installation, security settings,

and the settings on your router. Some rewall software programs may

block a DHCP request on newly installed adapters.

How to check your IP address?

If you are connecting to a wireless network at a hotspot (e.g. hotel, coee shop, airport), please contact an employee or administrator to verify

their wireless network settings.

Troubleshooting

If you are not using a DHCP capable gateway/router, or you need to

assign a static IP address, please follow the steps below:

Step 1:

Windows® 2000: Click on Start > Settings > Control Panel > Network

Connections

Windows XP: Click on Start > Control Panel > Network Connections

Windows Vista®: Click on Start > Control Panel > Network and Internet >

Network and Sharing Center > Manage network connections

Step 2:

Right-click on the Local Area Connection which represents your network

adapter and select Properties.

Step 3:

Highlight Internet Protocol (TCP/IP) and click Properties.

Step 4:

Click Use the following IP address and enter an IP address that is on the

same subnet as your network or the LAN IP address on your router.

Example: If the router’s LAN IP address is 192.168.0.1, make your IP

address 192.168.0.X where X is a number between 2 and 99. Make sure

that the number you choose is not in use on the network. Set Default

Gateway the same as the LAN IP address of your router (192.168.0.1).

Set Primary DNS the same as the LAN IP address of your router

(192.168.0.1). The Secondary DNS is not needed or you may enter a DNS

server from your ISP.

Step 5:

Click OK twice to save your settings.

How to statically assign an IP address?

Technical Specications

Standards

• IEEE 802.11ac

• IEEE 802.11n

• IEEE 802.11g

• IEEE 802.11a

• IEEE 802.3b

• IEEE 802.3u

• IEEE 802.3ab

• IEEE 802.3az

• IEEE 802.3af

Network Management

• Web Browser interface (HTTP, Secure HTTP (HTTPS))

• Nuclias Connect

Security

• WPA™ Personal/Enterprise

• WPA2™ Personal/Enterprise

• WEP™ 64-/128-bit

Wireless Frequency Range

• 2.4 to 2.4835 GHz and 5.15 to 5.85 GHz**

Power Input

• 12 to 48 V DC terminal block dual input

• 802.3at PoE

Antenna Type

• 2x Detachable 2.5 dBi Omni antennas @2.4GHz

• 2x Detachable 3 dBi Omni antennas @5GHz

LED Displays

• PWR1/PWR2/POE/ALARM/2.4G/5G/STATUS/SIGNAL

Temperature

• Operating: -20˚C to 65˚C

• Storing: -40˚C to 80˚C

Humidity

• Operating: 10%~90% (non-condensing)

• Storing: 5%~95% (non-condensing)

Certications

• FCC

• CE

• NCC

Dimensions

• L = 196.2 mm

• W = 105.9 mm

• H = 40 mm

Antenna Patterns

100

Antenna Patterns

Orientation H-Plane E-Plane

2.4 GHz Wall/DIN-rail Mounted

5 GHz Wall/DIN-rail Mounted