D-Link DMS-1100-10TS User Manual
Displayed below is the user manual for DMS-1100-10TS by D-Link which is a product in the Network Switches category. This manual has pages.
DMS-1100 Series
L2 2.5 Gigabit Ethernet
Switch Series
Ver. 1.00
D-Link DMS-1100 Series User Manual
i
i
Table of Contents
Table of Contents ............................................................................................................................................. i
About This Guide ............................................................................................................................................. 1
Terms/Usage .................................................................................................................................................. 1
Copyright and Trademarks ............................................................................................................................ 1
1 Product Introduction ................................................................................................................................... 2
DMS-1100-10TS ............................................................................................................................................ 3
Front Panel ................................................................................................................................................. 3
Rear Panel .................................................................................................................................................. 3
DMS-1100-10TP ............................................................................................................................................ 4
Front Panel ................................................................................................................................................. 4
Rear Panel .................................................................................................................................................. 4
DMS-1100 LED Indicators ............................................................................................................................. 5
2 Hardware Installation .................................................................................................................................. 7
Safety Cautions .............................................................................................................................................. 7
Step 1: Unpacking .......................................................................................................................................... 8
Step 2: Switch Installation .............................................................................................................................. 8
Desktop or Shelf Installation ....................................................................................................................... 8
Rack Installation ......................................................................................................................................... 9
Step 3 – Plugging in the AC Power Cord with Power Cord Clip .................................................................... 9
Power Failure ........................................................................................................................................... 12
Grounding the Switch ............................................................................................................................... 12
3 Getting Started ........................................................................................................................................... 13
Management Options ................................................................................................................................... 13
Using Web-based Management .................................................................................................................. 13
Supported Web Browsers ........................................................................................................................ 13
Connecting to the Switch .......................................................................................................................... 13
Login Web-based Management ............................................................................................................... 13
Smart Wizard ............................................................................................................................................... 14
Web-based Management ............................................................................................................................. 14
4 Configuration ............................................................................................................................................. 15
Smart Wizard Configuration ......................................................................................................................... 15
IPv4 Information ....................................................................................................................................... 15
SNMP Settings ......................................................................................................................................... 16
User Accounts Settings ............................................................................................................................ 16
Web-based Management ......................................................................................................................... 17
Tool Bar > Save Menu ................................................................................................................................. 18
Save Configuration ................................................................................................................................... 18
Tool Bar > Tool Menu .................................................................................................................................. 19
Firmware Information................................................................................................................................ 19
Configuration Information ......................................................................................................................... 19
Firmware Upgrade & Backup > Firmware Upgrade from HTTP .............................................................. 19
Firmware Upgrade & Backup > Firmware Upgrade from TFTP ............................................................... 20
Firmware Backup to HTTP & Backup > Firmware Backup to HTTP ........................................................ 20
Firmware Backup to HTTP & Backup > Firmware Backup to TFTP ........................................................ 21
Configuration Upgrade & Backup > Configuration Restore from HTTP ................................................... 21
Configuration Upgrade & Backup > Configuration Restore from TFTP ................................................... 22
Configuration Upgrade & Backup > Configuration Backup to HTTP ....................................................... 22
D-Link DMS-1100DMS-1100 Series User Manual
ii
Configuration Upgrade & Backup > Configuration Backup to TFTP ........................................................ 22
Log Backup > Log Backup to HTTP ......................................................................................................... 23
Log Backup > Log Backup to TFTP ......................................................................................................... 23
Ping .......................................................................................................................................................... 23
Reset ........................................................................................................................................................ 24
Reboot System ......................................................................................................................................... 24
Tool Bar > Smart Wizard .............................................................................................................................. 25
Tool Bar > Online Help ................................................................................................................................. 25
Function Tree ............................................................................................................................................... 27
Device Information.................................................................................................................................... 27
System > System Information .................................................................................................................. 27
System > Port Configuration > Port Settings ........................................................................................... 28
System > Port Configuration > Port Status .............................................................................................. 29
System > Port Configuration > Error Disable Settings ............................................................................. 29
System > Port Configuration > Jumbo Frame .......................................................................................... 30
System > PoE > PoE System (DMS-1100-10TP only) ............................................................................ 31
System > PoE > PoE Status (DMS-1100-10TP only) .............................................................................. 32
System > PoE > PoE Configuration (DMS-1100-10TP only) ................................................................... 32
System > PoE > PoE Measurement (DMS-1100-10TP only) .................................................................. 33
System > System Log > System Log Settings ......................................................................................... 33
System > System Log > System Log Server Settings ............................................................................. 34
System > System Log > System Log ....................................................................................................... 35
System > Time and SNTP > Clock Settings ............................................................................................ 35
System > Time and SNTP > Time Zone Settings .................................................................................... 35
System > Time and SNTP > SNTP Settings ............................................................................................ 37
Management > User Accounts Settings ................................................................................................... 38
Management > Password Encryption ...................................................................................................... 39
Management > SNMP > SNMP Global Settings ...................................................................................... 39
Management > SNMP > SNMP View Table Settings .............................................................................. 40
Management > SNMP > SNMP Community Table Settings .................................................................... 41
Management > SNMP > SNMP Group Table Settings ............................................................................ 42
Management > SNMP > SNMP Engine ID Local Settings ....................................................................... 43
Management > SNMP > SNMP User Table Settings ............................................................................... 43
Management > SNMP > SNMP Host Table Settings ............................................................................... 45
Management > Web ................................................................................................................................. 45
Management > Session Timeout ............................................................................................................. 46
Management > D-Link Discover Protocol Settings................................................................................... 46
L2 Features > FDB > Static FDB > Unicast Static FDB ........................................................................... 47
L2 Features > FDB > Static FDB > Multicast Static FDB ......................................................................... 48
L2 Features > FDB > MAC Address Table Settings ................................................................................ 49
L2 Features > FDB > MAC Address Table .............................................................................................. 50
L2 Features > 802.1Q VLAN .................................................................................................................... 50
L2 Features > Asymmetric VLAN ............................................................................................................. 51
L2 Features > VLAN Interface .................................................................................................................. 51
L2 Features > Auto Surveillance VLAN > Auto Surveillance Properties .................................................. 53
L2 Features > Auto Surveillance VLAN > MAC Settings and Surveillance Device ................................. 54
L2 Features > Voice VLAN > Voice VLAN Global .................................................................................... 55
L2 Features > Voice VLAN > Voice VLAN Port ....................................................................................... 55
L2 Features > Voice VLAN > Voice VLAN OUI ........................................................................................ 56
D-Link DMS-1100 Series User Manual
iii
L2 Features > Voice VLAN > Voice VLAN Device ................................................................................... 57
L2 Features > Voice VLAN > Voice VLAN LLDP-MED Device ................................................................ 57
L2 Features > STP > STP Global Settings .............................................................................................. 57
L2 Features > STP > STP Port Settings .................................................................................................. 59
L2 Features > STP > MST Configuration Identification............................................................................ 61
L2 Features > STP > STP Instance ......................................................................................................... 62
L2 Features > STP > MSTP Port Information .......................................................................................... 62
L2 Features > ERPS(G.8032) > ERPS .................................................................................................... 63
L2 Features > ERPS(G.8032) > ERPS Profile ......................................................................................... 65
L2 Features > Loopback Detection .......................................................................................................... 66
L2 Features > Link Aggregation ............................................................................................................... 67
L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Settings ................................. 69
L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Groups Settings .................... 71
L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Mrouter Settings ................... 72
L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Statistics Settings ................. 72
L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Setting ...................................... 73
L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Groups Settings ....................... 75
L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Mrouter Settings ...................... 76
L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Statistics Settings .................... 77
L2 Features > LLDP > LLDP Global Settings .......................................................................................... 78
L2 Features > LLDP > LLDP Port Settings .............................................................................................. 79
L2 Features > LLDP > LLDP Management Address List ......................................................................... 80
L2 Features > LLDP > LLDP Basic TLVs Settings ................................................................................... 81
L2 Features > LLDP > LLDP Dot1 TLVs Settings .................................................................................... 82
L2 Features > LLDP > LLDP Dot3 TLVs Settings .................................................................................... 82
L2 Features > LLDP > LLDP-MED Port Settings ..................................................................................... 84
L2 Features > LLDP > LLDP Statistics Information ................................................................................. 84
L2 Features > LLDP > LLDP Local Port Information ................................................................................ 86
L2 Features > LLDP > LLDP Neighbor Port Information.......................................................................... 87
L3 Features > IPv4 Interface .................................................................................................................... 87
L3 Features > IPv4 Default Gateway ....................................................................................................... 89
L3 Features > IPv6 Interface .................................................................................................................... 89
L3 Features > IPv6 Default Gateway ....................................................................................................... 90
QoS > Port Default CoS ........................................................................................................................... 91
QoS > Port Scheduler Method ................................................................................................................. 91
QoS > Queue Settings ............................................................................................................................. 92
QoS > CoS to Queue Mapping ................................................................................................................ 93
QoS > Port Rate Limiting .......................................................................................................................... 93
Security > Safeguard Engine.................................................................................................................... 94
Security > Trusted Host ............................................................................................................................ 94
Security > Traffic Segmentation Settings ................................................................................................. 95
Security > Storm Control Settings ............................................................................................................ 95
Security > DoS Attack Prevention Settings .............................................................................................. 97
Security > SSL > SSL Global Setting ....................................................................................................... 97
Security > SSL > SSL Service Policy ....................................................................................................... 98
OAM > Cable Diagnostics ........................................................................................................................ 99
Monitoring > Statistics > Port ................................................................................................................... 99
Monitoring > Statistics > Port Counters .................................................................................................. 100
Monitoring > Statistics > Counters ......................................................................................................... 102
D-Link DMS-1100DMS-1100 Series User Manual
iv
Monitoring > Mirror Settings ................................................................................................................... 103
Green > Power Saving ........................................................................................................................... 104
Green > EEE .......................................................................................................................................... 104
Appendix A - Technical Specifications ..................................................................................................... 106
Hardware Specifications ............................................................................................................................ 106
Features ..................................................................................................................................................... 108
L2 Features ............................................................................................................................................ 108
L3 Features ............................................................................................................................................ 108
VLAN ...................................................................................................................................................... 108
QoS (Quality of Service) ......................................................................................................................... 108
Security ................................................................................................................................................... 108
OAM ....................................................................................................................................................... 108
Management ........................................................................................................................................... 108
D-Link Green Technology ...................................................................................................................... 108
Appendix B – Rack mount Instructions .................................................................................................... 109
D-Link DMS-1100 Series User Manual
1
About This Guide
This guide provides installation and instructions for the D-Link 2.5 Gigabit Ethernet L2 Switch (DMS-1100-
10TS and DMS-1100-10TP).
Note: The model you have purchased may
appear slightly different from the illustrations
shown in the document. Refer to the sections for
detailed information about your switch, its
components, network connections, and technical
specifications.
This guide is divided into four parts:
1. Hardware Installation: Step-by-step hardware installation procedures.
2. Getting Started: A startup guide for basic switch installation and settings.
3. D-Link Network Assistant: An introduction to the central configuration utility.
4. Configuration: Information about the function descriptions and configuration settings.
Terms/Usage
In this guide, the term “Switch” (first letter capitalized) refers to the DMS-1100 Series switch and “switch”
(first letter lower case) refers to other Ethernet switches. Some technologies use “switch”, “bridge” and
“switching hubs” interchangeably, and all are commonly accepted terms for Ethernet switches.
A NOTE indicates important information that
helps you make better use of the device.
A CAUTION indicates the potential for property
damage or personal injury.
Copyright and Trademarks
Information in this document is subjected to change without notice.
© 2017 D-Link Corporation. All rights reserved.
Reproduction in any manner whatever without the written permission of D-Link Corporation is strictly
forbidden.
Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation; Microsoft
and Windows are registered trademarks of Microsoft Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the
marks and names or their products. D-Link Corporation disclaims any proprietary interest in trademarks and
trade names other than its own.
D-Link DMS-1100 Series User Manual
2
1 Product Introduction
Thank you and congratulations on your purchase of D-Link DMS-1100 Series Switch.
D-Link's latest generation L2 2.5 Gigabit Ethernet switch series blends plug-and-play simplicity with
exceptional value and reliability for small and medium-sized business (SMB) networking. All models are
housed in a new style rack-mount metal case with easy-to-view front panel diagnostic LEDs, and provide
advance features including network security, traffic segmentation, QoS and versatile management.
Flexible Port Configurations: The DMS-1100 Series is D-Link’s latest 2.5G switch which provides 8-port
2.5GBASE-T plus 2 SFP+ models. The DMS-1100 Series switches, have the advantage of using intuitive
feature-rich software and utilizing a neat and simplified Web GUI allowing users to access and configure the
Switch from everywhere via a web browser. 2.5GBASE-T provides the requisite backward compatibility that
allows end users to transparently upgrade from 100/1000Mbps to 2.5 Gbps, using Cat 5e, unshielded and
shielded twisted-pair cables. 10G SFP+ has the advantage of lower power consumption, longer cable
distance, and better latency performance. Direct Attach Cables (DACs) can be used to provide a cost
effective way of connecting switches at 10 Gbps that are in close proximity to each other.
D-Link Green Technology: D-Link Green devices aim to provide eco-friendly alternatives without
compromising performance. D-Link Green Technology includes a number of innovations to reduce energy
consumption on DMS-1100 series switches, such as reducing power when a port does not have a device
attached, or adjusting the power usage according to the length of Ethernet cable connected to it.
Extensive Layer 2 Features: Implemented as complete L2 devices, these switches include functions such
as IGMP snooping, port mirroring, Spanning Tree, ERPS, 802.3ad LACP, SNTP, LLDP and Loopback
Detection to enhance performance and network reliability.
QoS: The switches support bandwidth control and 802.1p priority queues, enabling users to run bandwidth-
sensitive applications such as voice and video on the network. These functions allow the switches to work
seamlessly with VLANs, 802.1p traffic and IPv6 Traffic Class priority to prioritize traffic on the network.
Network Security: D-Link’s innovative Safeguard Engine function protects the switches against traffic
flooding caused by virus attacks. Additional features such as Storm Control can help to keep the network
from being overwhelmed by abnormal traffic. Port Security is another simple but useful authentication
method to maintain the network device integrity.
Versatile Management: The new generation of D-Link 2.5 Gigabit Ethernet Switches provide growing
businesses with a simple and easy management of their network, using a web-based management interface
that allows administrators to remotely control their network down to the port level. Alternatively, the Switch
can also be managed, in-band, by using a Telnet connection to any of the LAN ports on the Switch.
Users can also access the switch via Telnet. Some basic tasks can be performed such as changing the
Switch IP address, resetting the settings to factory defaults, setting the administrator password and rebooting
the Switch.
In addition, users can utilize the SNMP MIB (Management Information Base) to poll the switches for
information about the status, or send out traps of abnormal events. SNMP support allows users to integrate
the switches with other third-party devices for management in an SNMP-enabled environment. D-Link Smart
Managed Switches provides easy-to-use graphic interface and facilitates the operation efficiency.
D-Link DMS-1100 Series User Manual
3
DMS-1100-10TS
8-Port 2.5GBASE-T and 2-Port 10G SFP+ Smart Managed Switch.
Front Panel
Figure 1.1 – DMS-1100-10TS Front Panel
Power LED : The Power LED lights up when the Switch is connected to a power source.
Fan Error: The Fan error LED lights up when the fan has runtime failure and is brought offline.
Reset: Press the Reset button for 1~5 seconds to reboot the device. Press the Reset button for 6~10
seconds to reset the Switch back to the default settings and led will be solid light with amber for 2 seconds.
Or press the Reset button over 11 seconds to enter the loader mode after device reboot and the led will be
solid light with green for 2 seconds. If the device cannot reboot the Switch, the device will enter the loader
mode automatically.
Port Link/Act/Speed LED (1-8): The port LEDs indicate a network link through the corresponding port.
Blinking indicates the Switch is either sending or receiving data to the port. When the port LED glows amber,
it indicates the port is running at 100 Mbps or 1000 Mbps. When the port LED glows green, it is running at
2.5 Gbps.
Port Link/Act/Speed LED (9F, 10F): The port LEDs indicate a network link through the corresponding port.
Blinking indicates the Switch is either sending or receiving data to the port. When the port LED glows green,
it is running at 1000 Mbps or 10 Gbps.
CAUTION: The MiniGBIC ports should use UL
listed Optical Transceiver product, Rated Laser
Class I. 3.3Vdc
Rear Panel
Figure 1.2 – DMS-1100-10TS Rear Panel
Power: Connect the AC power cord to this port.
D-Link DMS-1100 Series User Manual
4
DMS-1100-10TP
8-port 2.5GBASE-T PoE+ and 2-port 10G SFP+ Smart Managed Switch.
Front Panel
Figure 1.3 – DMS-1100-10TP Front Panel
Power LED : The Power LED lights up when the Switch is connected to a power source.
Fan Error: The Fan error LED lights up when the fan has runtime failure and is brought offline.
Reset: Press the Reset button for 1~5 seconds to reboot the device. Press the Reset button for 6~10
seconds to reset the Switch back to the default settings and led will be solid light with amber for 2 seconds.
Or press the Reset button over 11 seconds to enter the loader mode after device reboot and the led will be
solid light with green for 2 seconds. If the device cannot reboot the Switch, the device will enter the loader
mode automatically.
PoE OK/FAIL: The PoE LED shows the status of the PoE ports, the green light (OK) indicates that PoE work
fine and the amber light (Fail) indicate that the PoE is working abnormally.
Port Link/Act/Speed LED (1-8): The port LEDs indicate a network link through the corresponding port.
Blinking indicates the Switch is either sending or receiving data to the port. When the port LED glows amber,
it indicates the port is running at 100 Mbps or 1000 Mbps. When the port LED glows green, it is running at
2.5 Gbps.
Port Link/Act/Speed LED (9F, 10F): The port LEDs indicate a network link through the corresponding port.
Blinking indicates the Switch is either sending or receiving data to the port. When the port LED glows green,
it is running at 1000 Mbps or 10 Gbps.
CAUTION: The MiniGBIC ports should use UL
listed Optical Transceiver product, Rated Laser
Class I. 3.3Vdc.
Rear Panel
Figure 1.4 – DMS-1110-10TP Rear Panel
Power: Connect the AC power cord to this port.
D-Link DMS-1100 Series User Manual
5
DMS-1100 LED Indicators
The Switch supports LED indicators for Power, Fan Error, PoE OK/Fail and Link/Act for each port. The
following shows the LED indicators for the DMS-1100 series Smart Managed Switch along with an
explanation of each indicator.
Figure 1.5 –LED Indicators on DMS-1100 series
Location
LED Indicative
Color
Status
Description
Per Device
Power
Green
Solid Light
Power on.
Light off
Power off.
Fan Error
Red
Solid light
The fan has runtime failure and is
brought offline.
LED Per
2.5GBASE-T
Port
Link/Act/Speed
Green/Amber
Solid Green
When there is a secure 2.5Gbps
connection (or link) at any of the
ports.
Blinking Green
When there is reception or
transmission (i.e. Activity—Act) of
data occurring at any of the ports.
Solid Amber
When there is a secure
100/1000Mbps Ethernet connection
(or link) at any of the ports.
Blinking Amber
When there is reception or
transmission (i.e. Activity—Act) of
data occurring at any of the port.
Light off
No link.
LED Per SFP+
Port
Link/Act/Speed
Green/Amber
Solid Green
When there is a secure 10Gbps
connection (or link) at any of the
ports.
Blinking Green
When there is reception or
transmission (i.e. Activity—Act) of
data occurring at any of the ports.
Solid Amber
When there is a secure 1000Mbps
Ethernet connection (or link) at any
of the ports.
Blinking Amber
When there is reception or
transmission (i.e. Activity—Act) of
data occurring at any of the port.
Light off
No link.
LED Per PoE
Port
(DMS-1100-
10TP only)
PoE Status
Green/Amber
Solid Green
PD device insert and power feeding.
Solid Amber
PD device insert but failure occurs.
(PSE can't provide power to PD due
to PD error or power budget is not
enough.)
D-Link DMS-1100 Series User Manual
6
Light off
No PD device insert.
D-Link DMS-1100 Series User Manual
7
2 Hardware Installation
This chapter provides unpacking and installation information for the D-Link DMS-1100 Series Switch.
Safety Cautions
To reduce the risk of bodily injury, electrical shock, fire and damage to the equipment, observe the following
precautions:
Observe and follow service markings.
• Do not service any product except as explained in your system documentation.
• Opening or removing covers that are marked with the triangular symbol with a lightning bolt may
expose you to electrical shock.
Only a trained service technician should service components inside these compartments.
If any of the following conditions occur, unplug the product from the electrical outlet and replace the part
or contact your trained service provider:
• The power cable, extension cable, or plug is damaged.
• An object has fallen into the product.
• The product has been exposed to water.
• The product has been dropped or damaged.
• The product does not operate correctly when you follow the operating instructions.
Keep your system away from radiators and heat sources. Also, do not block cooling vents.
Do not spill food or liquids on your system components, and never operate the product in a wet
environment. If the system gets wet, contact your trained service provider.
Do not push any objects into the openings of your system. Doing so can cause fire or electric shock by
shorting out interior components.
Use the product only with approved equipment.
Allow the product to cool before removing covers or touching internal components.
Operate the product only from the type of external power source indicated on the electrical ratings label.
If you are not sure of the type of power source required, consult your service provider or local reseller.
Also, be sure that attached devices are electrically rated to operate with the power available in your
location.
Use only approved power cable(s). If you have not been provided with a power cable for your system or
for any AC powered option intended for your system, purchase a power cable that is approved for use in
your country. The power cable must be rated for the product and for the voltage and current marked on
the product’s electrical ratings label. The voltage and current rating of the cable should be greater than
the ratings marked on the product.
To help prevent electric shock, plug the system and peripheral power cables into properly grounded
electrical outlets.
These cables are equipped with three-prong plugs to help ensure proper grounding. Do not
use adapter plugs or remove the grounding prong from a cable. If you must use an extension
cable, use a 3-wire cable with properly grounded plugs.
Observe extension cable and power strip ratings. Make sure that the total ampere rating of all
products plugged into the extension cable or power strip does not exceed 80 percent of the
ampere ratings limit for the extension cable or power strip.
To help protect your system from sudden, transient increases and decreases in electrical
power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS).
Position system cables and power cables carefully; route cables so that they cannot be
stepped on or tripped over. Be sure that nothing rests on any cables.
D-Link DMS-1100 Series User Manual
8
Do not modify power cables or plugs. Consult a licensed electrician or your power company for
site modifications.
Always follow your local/national wiring rules.
When connecting or disconnecting power to hot-pluggable power supplies, if offered with your
system, observe the following guidelines:
• Install the power supply before connecting the power cable to the power supply.
• Unplug the power cable before removing the power supply.
• If the system has multiple sources of power, disconnect power from the system by
unplugging all power cables from the power supplies.
Move products with care; ensure that all casters and/or stabilizers are firmly connected to the system.
Avoid sudden stops and uneven surfaces.
Step 1: Unpacking
Open the shipping carton and carefully unpack its contents. Please consult the packing list located in the
User Manual to make sure all items are present and undamaged.
One D-Link DMS-1100 Series switch
One Multilingual Getting Started Guide
User Guide CD
Power Cord and Power Cord Retainer
Rack-mount kit and Rubber Feet
If any item is found missing or damaged, please contact the local reseller for replacement.
Step 2: Switch Installation
For safe switch installation and operation, it is recommended that you:
Visually inspect the power cord to see that it is secured fully to the AC power connector.
Make sure that there is proper heat dissipation and adequate ventilation around the switch.
Do not place heavy objects on the switch.
Desktop or Shelf Installation
When installing the switch on a desktop or shelf, the rubber feet included with the device must be attached
on the bottom at each corner of the device’s base. Allow enough ventilation space between the device and
the objects around it.
Figure 2.1 – Attach the adhesive rubber pads to the bottom
D-Link DMS-1100 Series User Manual
9
Rack Installation
The switch can be mounted in an EIA standard size 19-inch rack, which can be placed in a wiring closet with
other equipment. To install, attach the mounting brackets to the switch’s side panels (one on each side) and
secure them with the screws provided (with 8 M3*6.0 size screws).
Figure 2.2 – Attach the mounting brackets to the Switch
Then, use the screws provided with the equipment rack to mount the switch in the rack.
Figure 2.3 – Mount the Switch in the rack or chassis
Step 3 – Plugging in the AC Power Cord with Power Cord Clip
To prevent accidental removal of the AC power cord, it is recommended to install the power cord clip
together with the power cord.
A) With the rough side facing down, insert the Tie Wrap into the hole below the power socket.
Figure 2.1 – Insert Tie Wrap to the Switch
B) Plug the AC power cord into the power socket of the Switch.
D-Link DMS-1100 Series User Manual
10
Figure 2.2 – Connect the power cord to the Switch
C) Slide the Retainer through the Tie Wrap until the end of the cord.
Figure 2.3 – Slide the Retainer through the Tie Wrap
D) Circle the tie of the Retainer around the power cord and into the locker of the Retainer.
D-Link DMS-1100 Series User Manual
11
Figure 2.4 – Circle around the power cord
E) Fasten the tie of the Retainer until the power cord is secured.
Figure 2.5 – Secure the power cord
F) Users may now connect the AC power cord to an electrical outlet (preferably one that is grounded and
surge protected).
D-Link DMS-1100 Series User Manual
12
Figure 2.6 – Plugging the switch into an outlet
Power Failure
As a precaution, the switch should be unplugged in case of power failure. When power is resumed, plug the
switch back in.
Grounding the Switch
This section describes how to connect the DMS-1100 Series Switch to ground. You must complete this
procedure before powering your switch.
Required Tools and Equipment
Ground screws (included in the accessory kit): One M4 x 6 mm (metric) pan-head screw.
Ground cable (not included in the accessory kit): The grounding cable should be sized according to
local and national installation requirements. Depending on the power supply and system, a 12 to 6
AWG copper conductor is required for U.S installation. Commercially available 6 AWG wire is
recommended. The length of the cable depends on the proximity of the switch to proper grounding
facilities.
A screwdriver (not included in the accessory kit)
The following steps let you connect the switch to a protective ground:
Step 1: Verify if the system power is off.
Step 2: Use the ground cable to place the #8 terminal lug ring on top of the ground-screw opening, as
seen in the figure below.
Step 3: Insert the ground screw into the ground-screw opening.
Step 4: Using a screwdriver, tighten the ground screw to secure the ground cable to the switch.
Step 5: Attach the terminal lug ring at the other end of the grounding cable to an appropriate grounding
stud or bolt on rack where the switch is installed.
Step 6: Verify if the connections at the ground connector on the switch and the rack are securely
attached.
Figure 2.10 – Connect a Grounding Cable
D-Link DMS-1100 Series User Manual
13
3 Getting Started
This chapter introduces the management interface of D-Link DMS-1100 Series Switch.
Management Options
The D-Link DMS-1100 Series Switch can be managed through any port by using the Web-based
Management.
Each switch must be assigned its own IP Address, which is used for communication with the Web-Based
Management or a SNMP network manager. The PC should have an IP address in the same subnet as the
switch. Each switch can allow up to four users to access the Web-Based Management concurrently.
Please refer to the following installation instructions for the Web-based Management.
Using Web-based Management
After a successful physical installation, you can configure the Switch, monitor the network status, and display
statistics using a web browser.
Supported Web Browsers
The embedded Web-based Management currently supports the following web browsers:
Internet Explorer 7 or later version
Chrome
Firefox
Safari
Connecting to the Switch
You will need the following equipment to begin the web configuration of your device:
1. A PC with a RJ-45 Ethernet connection
2. A standard Ethernet cable
Connect the Ethernet cable to any of the ports on the front panel of the switch and to the Ethernet port on the
PC.
Figure 3.1 – Connected Ethernet cable
Login Web-based Management
In order to login and configure the switch via Web-based GUI, the PC must have an IP address in the same
subnet as the switch. For example, if the switch has an IP address of 10.90.90.90, the PC should have an IP
D-Link DMS-1100 Series User Manual
14
address of 10.x.y.z (where x/y is a number between 0 ~ 254 and z is a number between 1 ~ 254), and a
subnet mask of 255.0.0.0. There are two ways to launch the Web-based Management.
Figure 3.2 –Enter the IP address 10.90.90.90 in the web browser
NOTE: The switch's factory default IP address is
10.90.90.90 with a subnet mask of 255.0.0.0 and
a default gateway of 0.0.0.0.
When the following login dialog box appears, enter the password and choose the language of the Web-
based Management interface then click OK.
The switch supports 10 languages including English, Traditional Chinese, Simplified Chinese, German,
Spanish, French, Italian, Portuguese, Japanese and Russian. By default, the language is English. Enter the
User name and Password with “admin” and press Login to enter the main configuration window.
Figure 3.3 – Login Dialog Box
Smart Wizard
After a successful login, the Smart Wizard will guide you through essential settings of the D-Link DMS-1100
Series Switch. Please refer to the Smart Wizard Configuration section for details.
Web-based Management
By clicking the Exit button in the Smart Wizard, you will enter the Web-based Management interface. Please
refer to Chapter 4 Configuration for detailed instructions.
D-Link DMS-1100 Series User Manual
15
4 Configuration
The features and functions of the D-Link DMS-1100 Series Switch can be configured for optimum use
through the Web-based Management Utility.
Smart Wizard Configuration
After a successful login, the Smart Wizard will guide you through essential settings of the D-Link DMS-1100
Series Switch. If you do not plan to change anything, click Exit to leave the Wizard and enter the Web
Interface. You can also skip it by clicking Ignore the wizard next time for the next time you logon to the
Web-based Management.
IPv4 Information
IPv4 Information will guide you to do basic configurations on 3 steps for the IP Information, access password,
and SNMP. Select Static, to manually enter a new IP Address, Netmask and Gateway address, or select
DHCP to automatically receive IP settings from a DHCP server. Click the Next button to enter the SNMP
settings page The IP address is allowed for IPv4 and IPv6 address. If you are not changing the settings, click
Exit button to go back to the main page. Or you can click on Ignore the wizard next time to skip wizard
setting when the switch boots up.
Figure 4.1 – IPv4 Information in Smart Wizard
D-Link DMS-1100 Series User Manual
16
NOTE: The IPv4 Information of Smart Wizard
does not support IPv6 address.
SNMP Settings
The SNMP Settings page allows user to quickly enable/disable the SNMP function. The default SNMP
Setting is Disabled. Click Enabled and then click Next, then it will enter the User Accounts Settings page.
Figure 4.2 – SNMP Settings in Smart Wizard
User Accounts Settings
The User Accounts Settings page allows user to quickly specify the user account function. Enter the User
Name, Privilege, Password Type and Password. Click Apply & Save to save the configuration.
D-Link DMS-1100 Series User Manual
17
Figure 4.3 – User Accounts Setting in Smart Wizard
Web-based Management
After clicking the Exit button in the Smart Wizard you will see the screen below:
Figure 4.4 – Web-based Management
D-Link DMS-1100 Series User Manual
18
The above image is the Web-based Management screen. The three main areas are the Tool Bar on top, the
Function Tree, and the Main Configuration Screen.
The Tool Bar provides a quick and convenient way for essential utility functions like firmware and
configuration management.
By choosing different functions in the Function Tree, you can change all the settings in the Main
Configuration Screen. The main configuration screen will show the current status of your Switch by clicking
the model name on top of the function tree.
At the upper right corner of the screen the username and current IP address will be displayed.
Under the username is the Logout button. Click this to end this session.
NOTE: If you close the web browser without
clicking the Logout button first, then it will be seen
as an abnormal exit and the login session will still
be occupied.
Click the D-Link logo at the upper-left corner of the screen to be redirected to the local D-Link website.
Tool Bar > Save Menu
The Save Menu provides Save Configuration and Save Log functions.
Figure 4.5 – Save Menu
Save Configuration
The Save Configuration page allows user to save the configuration changes to the S witch’s non-volatile
RAM.
Figure 4.6 – Save Configuration
The fields that can be configured for Save Configuration are described below:
Item
Description
Destination
Select the destination to save the configuration to.
Startup-config
Check the box to enable the startup configuration function.
Table 4.1
Click Apply to make the configurations take effect.
D-Link DMS-1100 Series User Manual
19
Tool Bar > Tool Menu
The Tool Menu offers global functions controls such as Reset, Reboot Device, Configuration Backup and
Restore, Firmware Backup and Upgrade.
Figure 4.7 – Tool Menu
Firmware Information
The Firmware Information page displays the firmware image information, including the image that has been
booted and the image that is selected for the next reboot.
Figure 4.8 – Tool Menu > Firmware Information
Configuration Information
The Configuration Information page displays information for the Switch configuration. This includes the
configuration that has been loaded and the configuration that is selected for the next reboot.
Figure 4.9 – Tool Menu > Configuration Information
Firmware Upgrade & Backup > Firmware Upgrade from HTTP
The Firmware upgrade from HTTP page allows user to upgrade the firmware of Switch from a firmware file.
D-Link DMS-1100 Series User Manual
20
Figure 4.10 – Tool Menu > Firmware Upgrade & Backup > Firmware Upgrade from HTTP
The fields that can be configured for Firmware Upgrade are described below:
Item
Description
Source URL
Click Choose File button to select the source URL to upgrade the
configuration from.
Destination URL
Displays the destination URL to upgrade to.
Table 4.2
Click Upgrade button to upload firmware to the Switch via HTTP.
Note: The Switch will reboot after restoring the
firmware, and all current configurations will be lost.
Firmware Upgrade & Backup > Firmware Upgrade from TFTP
This Firmware Upgrade from TFTP page allows user to upgrade firmware using TFTP.
Figure 4.11 – Tool Menu > Firmware Upgrade & Backup > Firmware Upgrade from TFTP
The fields that can be configured for Firmware Upgrade from TFTP are described below:
Item
Description
TFTP Server IP
Select IPv4 or IPv6 and enter the address to be configured.
Source URL
Enter the source URL address.
Destination URL
Displays the destination URL address.
Table 4.3
Click the Upgrade button to upgrade the firmware from specified TFTP address.
Note: The Switch will reboot after
restoring the firmware, and all current
configurations will be lost.
Firmware Backup to HTTP & Backup > Firmware Backup to HTTP
The Firmware Backup to HTTP page allows user to save a backup of the firmware, select the source URL
and then click Backup.
D-Link DMS-1100 Series User Manual
21
Figure 4.12 – Tool Menu > Firmware Upgrade & Backup > Firmware Backup to HTTP
The fields that can be configured for Firmware Backup to HTTP are described below:
Item
Description
Source URL
Select the source URL to be backup to.
Table 4.4
Click Backup button to backup the specified firmware.
Firmware Backup to HTTP & Backup > Firmware Backup to TFTP
The Firmware Backup to TFTP allows user to save a backup of the firmware using TFTP, enter the TFTP
server IP address, the source URL, and the destination URL. Click Backup.
Figure 4.13 – Tool Menu > Firmware Upgrade & Backup > Firmware Backup to TFTP
The fields that can be configured for Firmware Backup to TFTP are described below:
Item
Description
TFTP Server IP
Select IPv4 or IPv6 and enter the address to be configured.
Source
Enter the source URL address.
Destination URL
Displays the destination URL address.
Table 4.5
Click the Upgrade button to upgrade the firmware to specified TFTP address.
Configuration Upgrade & Backup > Configuration Restore from HTTP
The Configuration Restore from HTTP page allows user to restore the Switch from a saved configuration file.
Figure 4.14 – Tool Menu > Configuration Upgrade & Backup > Configuration Restore from HTTP
The fields that can be configured for Configuration Restore are described below:
Item
Description
Source URL
Click Choose File button to select the source URL to restore the
configuration from.
D-Link DMS-1100 Series User Manual
22
Destination URL
Displays the destination URL to upgrade to.
Startup-config
Check the box to enable the startup configuration function.
Table 4.6
Click Restore button to upload configuration to the Switch via HTTP.
Configuration Upgrade & Backup > Configuration Restore from TFTP
The Configuration Restore from TFTP page allows user to load the Switch’s configuration from a saved
configuration file using TFTP.
Figure 4.15 – Tool Menu > Configuration Upgrade & Backup > Configuration Restore from TFTP
The fields that can be configured for Configuration Restore from TFTP are described below:
Item
Description
TFTP Server IP
Select IPv4 or IPv6 and enter the address to be configured.
Destination URL
Displays the destination URL address.
Startup-config
Check the box to enable the startup configuration function.
Source URL
Enter the source URL address.
Table 4.7
Click the Restore button to upgrade the configuration from specified TFTP address.
Configuration Upgrade & Backup > Configuration Backup to HTTP
The Configuration Backup to HTTP page allows user to save the current configuration to a file.
Figure 4.16 – Tool Menu > Configuration Upgrade & Backup > Configuration Backup to HTTP
Configuration Upgrade & Backup > Configuration Backup to TFTP
The Configuration Backup to TFTP page allows user to save the current configuration to a file using TFTP.
Figure 4.17 – Tool Menu > Configuration Upgrade & Backup > Configuration Backup to TFTP
D-Link DMS-1100 Series User Manual
23
The fields that can be configured for Configuration Backup from TFTP are described below:
Item
Description
TFTP Server IP
Select IPv4 or IPv6 and enter the address to be configured.
Source
Enter the source URL address.
Startup-config
Check the box to enable the startup configuration function.
Destination URL
Displays the destination URL address.
Table 4.8
Click the Backup button to save the configuration from specified TFTP address.
Log Backup > Log Backup to HTTP
The Log Backup to HTTP page allows user to save the log to a file.
Figure 4.18 – Tool Menu > Log Backup > Log Backup to HTTP
Log Backup > Log Backup to TFTP
The Log Backup to TFTP page allows user to save the log to a file using TFTP.
Figure 4.19 – Tool Menu > Log Backup > Log Backup to TFTP
The fields that can be configured for Log Backup are described below:
Item
Description
TFTP Server IP
Select IPv4 or IPv6 and enter the address to be configured.
Destination URL
Enter the destination URL for the backup.
Table 4.9
Click the Backup button to save the log to specified TFTP address.
Ping
The Ping page allows user to ping a computer or device. The result will be displayed in the Result box.
D-Link DMS-1100 Series User Manual
24
Figure 4.20 – Ping
The fields that can be configured for Ping are described below:
Item
Description
IPv4 Ping
Target Ipv4 Address
Enter the IPv4 address to be pinged.
Ping Times (1-255)
Specify the ping time. The range is from 1 to 255.
Timeout (1-99)
Specify the timeout period while waiting for a response from the remote
device. The range is from 1 to 99 seconds.
IPv6 Ping
Target Ipv6 Address
Enter the IPv6 address to be pinged.
Ping Times (1-255)
Specify the ping time. The range is from 1 to 255.
Timeout (1-99)
Specify the timeout period while waiting for a response from the remote
device. The range is from 1 to 99 seconds.
Table 4.10
Click Apply to make the configurations take effect.
Reset
Select which reset option you want to perform and click Apply.
Figure 4.21 – Tool Menu > Reset
Reboot System
Select to save your current settings and then click Reboot to restart the Switch.
Figure 4.22 – Tool Menu > Reboot System
D-Link DMS-1100 Series User Manual
25
The fields that can be configured for Reboot System are described below:
Item
Description
Destination
Select the configuration destination to be saved.
Startup-config
When checking the box, only the current startup configuration file will
be backed up which may be stored in the “Config 1” location.
Table 4.11
Click Reboot to reboot the system with specified configuration.
Tool Bar > Smart Wizard
By clicking the Smart Wizard button, you can re-run to the Smart Wizard if you wish to make any changes.
Tool Bar > Online Help
The Online Help provides two ways of online support: D-link Support Site will lead you to the D-Link
website where you can find online resources such as updated firmware; User Guide can offer an immediate
reference for the feature definition or configuration guide.
Figure 4.23 – Online Help
D-Link DMS-1100 Series User Manual
26
Figure 4.24 – User Guide Micro Site
D-Link DMS-1100 Series User Manual
27
Function Tree
All configuration options on the switch are accessed through the Setup menu on the left side of the main
window. Click on the setup item that you want to configure. The following sections provide more detailed
description of each feature and function.
Figure 4.25 –Function Tree
Device Information
The Device Information provides an overview of the switch, including essential information such as firmware
& hardware information, and IP settings.
Figure 4.26 – Device Information
System > System Information
The System Setting page allows user to configure basic system information.
D-Link DMS-1100 Series User Manual
28
Figure 4.27 – System > System Information
The fields that can be configured for System Information are described below:
Item
Description
System name
Enter the system name to be specified.
System Location
Enter the system location to be specified.
System Contact
Enter the system contact to be specified.
Table 4.12
Click Apply to make the configurations take effect.
System > Port Configuration > Port Settings
In the Port Settings page, the status of all ports can be monitored and adjusted for optimum configuration.
Figure 4.28 – System > Port Configuration > Port Settings
The fields that can be configured for Port Settings are described below:
Item
Description
From Port / To Port
Select the appropriate port range to be configured.
Media
Select the media type for specified port. The media type is Copper for
port 1 ~ port 8 and Fiber for port 9 ~ port 10.
State
Enable or disable the physical port.
Flow Control
Select On or Off. Ports configured for full-duplex use 802.3x flow
control, half-duplex ports use back-pressure flow control, and Auto
ports use an automatic selection of the two.
Duplex
Select the duplex mode used. Options to choose from are Auto and
D-Link DMS-1100 Series User Manual
29
Full.
Speed
Select the speed for the ports. The speed values are Auto, 10M,
100M, 1000M, 2.5G and 10G. Any other configuration will result in a
link down status for both ports.
Capability Advertised
When the Speed is set to Auto, these capabilities are advertised
during auto-negotiation. When specify the port 1 ~ port 8, these
capabilities advertised with 10G cannot be selected. When specify the
port 9 ~ port 10, the capability advertised can be selected with 1000M
and 10G.
Description
Enter a 64 characters description for the corresponding port.
Table 4.13
Click Apply to make the configurations take effect.
Click the Refresh button to refresh the displayed table.
System > Port Configuration > Port Status
The Port Settings page allows user to view the Switch’s physical port status and settings. The table will
display the Port, Status, MAC Address, VLAN, Flow Control Operator, Duplex, and Speed.
Figure 4.29 – System > Port Configuration > Port Status
System > Port Configuration > Error Disable Settings
The Error Disable Settings page allows user to configure the sending of SNMP notifications for error disable
state.
D-Link DMS-1100 Series User Manual
30
Figure 4.30 – System > Port Configuration > Error Disable Settings
The fields that can be configured for Error Disable Settings are described below:
Item
Description
Error Disable Trap Settings
Asserted
Select to enable or disable the notifications when entering into the error
disabled state.
Cleared
Select to enable or disable the notifications when exiting from the error
disabled state.
Notification Rate (0-1000)
Enter the number of traps per minute. The packets that exceed the rate
will be dropped. The value is between 0 and 1000.
Error Disable Recovery Settings
ErrDisable Cause
Specify the error disable causes. Options to choose from are Storm
and Loopback Detect.
State
Select to enable or disable the auto-recovery for an error port caused
by the specified cause.
Interval (5-586400)
Enter the time interval. The values are between 5 and 586400
seconds. And default value is 300.
Table 4.14
Click Apply to make the configurations take effect.
System > Port Configuration > Jumbo Frame
The Jumbo Frame page allows user to view and configure the Jumbo Frame settings.
Figure 4.31 –System > Port Configuration > Jumbo Frame
The fields that can be configured for Jumbo Frame are described below:
Item
Description
From Port / To Port
Specify the port to be configured.
Maximum Receive Frame Size
(1518-9216)
Specify the maximum receive frame size. The range is between 1518
and 9216. The default value is 1536.
Table 4.15
D-Link DMS-1100 Series User Manual
31
Click Apply to make the configurations take effect.
System > PoE > PoE System (DMS-1100-10TP only)
DMS-1100-10TP supports Power over Ethernet (PoE) as defined by the IEEE specification. It supplies power
to PD device up to 30W for port 1~8, meeting IEEE802.3af standards and pre-802.3at standards.
DMS-1100-10TP works with all D-Link 802.3af or 802.3at capable devices. The Switch is highly compatible
with all IEEE 802.3at/af compliant equipment, and transform the PoE to provide power to D-Link wireless
APs, IP Cams, IP phones. And also works with DPE-301GS PoE splitter providing 30W power to legacy PD
devices.
IEEE 802.3af defined that the PSE provides power according to the following classification:
Class
Usage
Minimum Power Levels
Output at the PSE
Maximum Power Levels at
the Powered Device
0
Default
15.4W
0.44 to 12.95W
1
Optional
4.0W
0.44 to 3.84W
2
Optional
7.0W
3.84 to 6.49W
3
Optional
15.4W
6.49 to 12.95W
4
Optional
Treat as Class 0
Reserved for future use
IEEE 802.3at defined that the PSE provides power according to the following classification:
Class
Usage
Powered Device
Classification
Guaranteed output
power by PSE Output
Maximum Power Levels
at the Powered Device
0
Default
Default, Type 1
15.4W
0.44 to 12.95W
1
Optional
Type 1
4.0W
0.44 to 3.84W
2
Optional
Type 1
7.0W
3.84 to 6.49W
3
Optional
Type 1
15.4W
6.49 to 12.95W
4
Optional
Type 2
30W
12.95 to 25.5W
IEEE 802.3at defined that the PSE provides power according to the following classification: The PoE System
page is used to configure the PoE system for PoE modules.
Figure 4.32 –System > PoE > PoE System
The fields that can be configured for PoE System are described below:
Item
Description
Power Budget (W)
Displays the power budget of Watts on the device
D-Link DMS-1100 Series User Manual
32
Delivered (W)
Displays how much power of Watts had been delivered.
Legacy Support
Specify to enable or disable detecting legacy PDs signal. The default is
disabled.
Table 4.16
Click Apply to make the configurations take effect.
Note: This product is to be connected only to PoE
networks without routing to the outside plant.
System > PoE > PoE Status (DMS-1100-10TP only)
The PoE Status page displays the PoE status of each port.
Figure 4.33 –System > PoE > PoE Status
Note: For the PoE Port Settings table, if the
classification was shown as “Legacy PD”, it will be
classified to non-AF PD or Legacy PD.
System > PoE > PoE Configuration (DMS-1100-10TP only)
The PoE Configuration page is used to configure the PoE port.
Figure 4.34 –System > PoE > PoE Configuration
The fields that can be configured for PoE Configuration are described below:
Item
Description
From Port / To Port
Select the appropriate port range used for the configuration.
D-Link DMS-1100 Series User Manual
33
Pirority
Select the priority for provisioning power to the port. Options to choose
from are Critical, High and Low.
Mode
Select the power management mode for the PoE ports. Options to
choose from are Auto, Class 1, Class 2, Class 3, and Class 4.
Max Wattage (1000-30000)
When selecting Auto in the Mode drop-down list, this option appears.
Tick the check box and enter the maximum wattage of power that can
be provisioned to the auto-detected PD. If the value is not entered, the
class of the PD automatically determines the maximum wattage which
can be provisioned. The valid range for maximum wattage is between
1000 mW and 30000 mW.
Table 4.17
Click Apply to make the configurations take effect.
Note: For DMS-1100-10TP, the port 1 ~ port 8 are compliance with
802.3at. The total PoE budget is 240 Watts.
System > PoE > PoE Measurement (DMS-1100-10TP only)
The PoE measurement page displays the measurement information of PoE ports.
Figure 4.35 –System > PoE > PoE Measurement
System > System Log > System Log Settings
The System Log Settings page allows user to view and configure the system’s log settings.
Figure 4.36 – System > System Log > System Log Settings
The fields that can be configured for System Log Settings are described below:
Item
Description
Global Settings
D-Link DMS-1100 Series User Manual
34
Source Interface State
Select to enable or disable the source interface’s global state.
Type
Select the type of interface that will be used. The default option is
VLAN.
VID (1-4094)
Specifies the VLAN ID. The possible range is 1 – 4094.
Buffer Log Settings
Buffer Log State
Select to enable or disable the buffer log state.
Severity
Select the severity value of the type of information that will be logged.
The values are 0 (Emergencies), 1 (Alerts), 2 (Critical), 3 (Errors), 4
(Warnings), 5 (Notifications), 6 (Informational), and 7 (Debugging).
Write Delay (0-65535)
Enter the interval for periodic writing of the logging buffer to flash. The
value is between 0 and 65535 seconds. And default is 300 seconds.
Tick the Infinite option, to disable the write delay feature.
Table 4.18
Click Apply to make the configurations take effect.
System > System Log > System Log Server Settings
The System Log Server Settings page allows user to view and configure the system log’s server settings.
Figure 4.37 – System > System Log > System Log Server Settings
The fields that can be configured for System Log Server Settings are described below:
Item
Description
IPv4 Address
Select and enter the IPv4 address.
UDP Port (514 or 1024-65535)
Enter the system log server’s UDP port number. This value must be
514 or between 1024 and 65535. The default value is 514.
Severity
Select the severity value of the type of information that will be logged.
Options to choose from are 0 (Emergencies), 1 (Alerts), 2 (Critical), 3
(Errors), 4 (Warnings), 5 (Notifications), 6 (Informational), and 7
(Debugging).
Facility
Select the facility value. The values must be between 0 and 23.
Table 4.19
Click Apply to make the configurations take effect and click the Delete button to remove the entry.
D-Link DMS-1100 Series User Manual
35
System > System Log > System Log
The System Log page displays the system logs on the Switch.
Figure 4.38 – System > System Log > System Log
System > Time and SNTP > Clock Settings
The Clock Settings page allows user to configure the time settings for the Switch.
Figure 4.39 – System > Time and SNTP > Clock Settings
The fields that can be configured for Clock Settings are described below:
Item
Description
Time (HH:MM:SS)
Enter the current time in hours, minutes, and seconds.
Data (DD/MM/YYYY)
Enter the current day, month, and year to update the system clock.
Table 4.20
Click Apply to make the configurations take effect.
System > Time and SNTP > Time Zone Settings
The Time Zone Settings page allows user to configure time zones and Daylight Saving Time settings for
SNTP.
D-Link DMS-1100 Series User Manual
36
Figure 4.40 – System > Time and SNTP > Time Zone Settings
The fields that can be configured for Time Zone Settings are described below:
Item
Description
Time Zone Settings
Summer Time State
Select Summer Time State setting. Options to choose from are
Disabled, Recurring Setting, and Date Setting.
Time Zone
Select the local time zone’s offset from Coordinated Universal Time
(UTC).
Recurring Settings
From: Week of the Month
Select week of the month that daylight saving time will start.
From: Day of the Week
Select day of the week that daylight saving time will start.
From: Month
Select the month that daylight time will start.
From: Time in HH MM
Select the time of the day that daylight saving time will start.
To: Week of the Month
Select week of the month that daylight saving time will end.
To: Day of the Week
Specify day of the week that daylight saving time will end.
To: Month
Select the month that daylight saving time will end.
To: Time In HH MM
Select the time of the day that daylight saving time will end.
Offset
Enter the number of minutes to add during daylight saving time. The
default value is 60. The range of this offset is 30, 60, 90 and 120.
Date Settings
D-Link DMS-1100 Series User Manual
37
From: Date of the Month
Select date of the month that daylight saving time will start.
From: Month
Select the month that daylight saving time will start.
From: Year
Select the year that the daylight saving time will start.
From: Time In HH MM
Select the time of the day that daylight saving time will start.
To: Date of the Month
Select the date of the month that daylight saving time will end.
To: Month
Select the month that daylight saving time will end.
To: Year
Select the year that the daylight saving time will end.
To: Time In HH MM
Select the time of the day that daylight time will end.
Offset
Select the number of minutes to add during daylight saving time. The
default value is 60. The range of this offset is 30, 60, 90 and 120.
Table 4.21
Click Apply to make the configurations take effect.
System > Time and SNTP > SNTP Settings
The SNTP Settings page allows user to configure the time settings for the Switch.
Figure 4.41 – System > Time and SNTP > SNTP Settings
The fields that can be configured for SNTP Settings are described below:
Item
Description
SNTP Global Settings
SNTP State
Select to enable or disable the SNTP state.
Poll Interval (30-99999)
Enter the poll interval. The value is from 30 to 99999 seconds. The
default interval is 720 seconds.
SNTP Server Settings
IPv4 Address
Enter the IPv4 address of the SNTP server which provides the clock
synchronization.
Table 4.22
Click Apply to make the configurations take effect.
D-Link DMS-1100 Series User Manual
38
Management > User Accounts Settings
The User Accounts Settings page allows user to create and configure user accounts. Active user account
sessions can be viewed. By default, there is no user account created on the Switch.
The pre-defined user account privilege levels supported by this switch are:
Basic User – Privilege Level 1. This user account level has the lowest priority of the user accounts.
The purpose of this type of user account level is for basic system checking.
Operator – Privilege Level 12. This user account level is used to grant system configuration
information for users who need to change or monitor system configuration, except for security related
information such as user accounts and SNMP account settings.
Administrator – Privilege Level 15. This administrator user account level can monitor all system
information and change any of the system configuration settings expressed in this guide.
Figure 4.42 – Management > User Accounts Settings
The fields that can be configured for User Accounts Settings are described below:
Item
Description
User Name
Enter the name of the user name. The name can be up to 32
characters long.
Privilege (1-15)
Select the privilege level for this account. The value is between 1 and
15.
Password Type
Select a password type for this user account. The options are None,
Plain Text, and Encrypted.
Password
If you selected either Plain Text or Encrypted for the password type,
please enter a password for this user account.
Table 4.23
Click Apply to make the configurations take effect.
Click the Delete button to remove the specified user account entry.
After clicking the Session Table tab, the following page will appear:
Figure 4.43 – Management > User Accounts Settings – Session Table
D-Link DMS-1100 Series User Manual
39
Management > Password Encryption
The Password Encryption page allows user to enable or disable password encryption.
Figure 4.44 – Management > Password Encryption
The fields that can be configured for Password Encryption are described below:
Item
Description
Password Encryption State
Specify to enable or disable the password encryption.
Password Type
Specify the password encryption type to Encrypted-SHA1 or
Encrypted-MD5.
Table 4.24
Click Apply to make the configurations take effect.
Management > SNMP > SNMP Global Settings
Simple Network Management Protocol (SNMP) is an OSI Layer 7 (Application Layer) protocol designed
specifically for managing and monitoring network devices. SNMP enables network management stations to
read and modify the settings of gateways, routers, switches, and other network devices. Use SNMP to
configure system features for proper operation, monitor performance and detect potential problems on the
Switch or your local network.
Managed devices that support SNMP include software (referred to as an agent), which runs locally on the
device. A defined set of variables (managed objects) is maintained by the SNMP agent and used to manage
the device. These objects are defined in a Management Information Base (MIB), which provides a standard
presentation of the information controlled by the on-board SNMP agent. SNMP defines both the format of the
MIB specifications and the protocol used to access this information over the network.
The default SNMP global state is disabled. Select Enable and then select Trap Settings. Click Apply to
enable the SNMP function.
Figure 4.45 – Management > SNMP > SNMP Global Settings
The fields that can be configured for SNMP Global Settings are described below:
Item
Description
D-Link DMS-1100 Series User Manual
40
SNMP Global Settings
SNMP Global State
Specify to enable or disable the SNMP feature. The default setting is
Disabled.
SNMP Response Broadcast
Request
Select to enable or disable the server to response to broadcast SNMP
GetRequest packets.
SNMP UDP Port (0-65535)
Enter the SNMP UDP port number. The value is between 0 and 65535.
Trap Source Interface
Specify the interface whose IP address will be used as the source
address for sending the SNMP trap packet.
Trap Settings
Trap Global State
Enable or disable SNMP trap notifications from client devices.
Disabling this option means no trap signals will be sent. When enabling
this option, you may choose the type of SNMP traps to enable.
SNMP Authentication Trap
Tick this option to control the sending of SNMP authentication failure
notifications. An authentication Failure trap is generated when the
device receives an SNMP message that is not properly authenticated.
The authentication method depends on the version of SNMP being
used. For SNMPv1 or SNMPv2c, authentication failure occurs if
packets are formed with an incorrect community string. For SNMPv3,
authentication failure occurs if packets are formed with an incorrect
SHA/MD5 authentication key.
Port Link Up
Check this feature to enable Link Up traps. Whenever a device
changes status from ‘link down’ to ‘link up’, it will send a Link Up trap to
the management station.
Port Link Down
Check this feature to enable Link Down traps. Whenever a device
changes status from ‘link up’ to ‘link down’, it will send a Link Down
trap to the management station.
STP Port Status Change
Check this feature to enable STP Port Status Change traps. Whenever
a device changes status from STP Port Status, it will send a STP Port
Status Change trap to the management station.
LBV Detection
Check this feature to enable LBV Detection traps. Whenever a device
does detect LBV, it will send a LBV Detection trap to the management
station.
Firmware Upgrade
Check this feature to enable Firmware Upgrade traps. Whenever a
device does do firmware upgrade, it will send a Firmware Upgrade trap
to the management station.
Table 4.25
Click Apply to make the configurations take effect.
Management > SNMP > SNMP View Table Settings
The SNMP View page allows user to define SNMP Views, which can be used to manage the MIB objects
that are accessible to a remote SNMP manager.
D-Link DMS-1100 Series User Manual
41
Figure 4.46 – Management > SNMP > SNMP View Table Settings
The fields that can be configured for SNMP View Table Settings are described below:
Item
Description
View Name
Create a name of the view, up to 32 characters.
Subtree OID
The Object Identifier (OID) Subtree for the view. The OID identifies an
object tree (MIB tree) that will be included or excluded from access by
an SNMP manager.
View Type
Select the OIDs that can accessed by a SNMP manager.
Table 4.26
Click Add to create a new view or Delete to remove an existing view.
Management > SNMP > SNMP Community Table Settings
The SNMP Community page allows user to set the SNMP community string of the Switch. SNMP managers
using the same community string are permitted access to the Switch's SNMP agent.
Figure 4.47 – Management > SNMP > SNMP Community Table Settings
The fields that can be configured for SNMP Community Table Settings are described below:
Item
Description
D-Link DMS-1100 Series User Manual
42
Key Type
Select the key type for the SNMP community. Select either Plain Text
or Encrypted.
Community Name
Select an alphanumeric string of up to 32 characters that is used to
identify members of an SNMP community. This string is used like a
password to give remote SNMP managers access to MIB objects in the
Switch’s SNMP agent.
View Name
Enter an alphanumeric string of up to 32 characters that is used to
identify the group of MIB objects that a remote SNMP manager is
allowed access to on the Switch. The view name must exist in the
SNMP View Table.
Access Right
Select the user’s access rights from the drop-down menu:
◆ Read Only - SNMP community members can read the contents
of the MIBs on the Switch.
◆ Read Write - SNMP community members can read and write the
contents of the MIBs on the Switch.
Table 4.27
Click Add to a new entry based on the information entered or Delete to remove the specified entry.
Management > SNMP > SNMP Group Table Settings
The SNMP Group page allows user to manage SNMP Groups. Access to SNMP OIDs and security policies
can be controlled on a per group basis.
Figure 4.48 – Management > SNMP > SNMP Group Table Settings
The fields that can be configured for SNMP Group Table Settings are described below:
Item
Description
Group Name
Enter a SNMP group name of up to 32 characters.
User-based Security Model
Select the SNMP security model.
◆ SNMPv1 - SNMPv1 does not support any security features.
◆ SNMPv2c - SNMPv2 supports both centralized and distributed
network management strategies. It includes improvements in the
Structure of Management Information (SMI) and adds some
security features.
D-Link DMS-1100 Series User Manual
43
◆ SNMPv3 - SNMPv3 provides secure access to devices through a
combination of authentication and encryption.
Security Level
This function is only available when you select SNMPv3 security level.
◆ NoAuthNoPriv – No authorization and no encryption for packets
sent between the Switch and SNMP manager.
◆ AuthNoPriv – Authorization is required, but no encryption for
packets sent between the Switch and SNMP manager.
◆ AuthPriv – Both authorization and encryption are required for
packets sent between the Switch and SNMP manger.
Read View Name
Enter a SNMP group name for users that are allowed SNMP read
privileges to the Switch's SNMP agent.
Write View Name
Enter a SNMP group name for users that are allowed SNMP write
privileges to the Switch's SNMP agent.
Notify View Name
Enter a SNMP group name for users that can receive SNMP trap
messages generated by the Switch's SNMP agent.
Table 4.28
Click the Add button to add a new entry based on the information entered.
Click the Delete button to remove the specified entry.
Management > SNMP > SNMP Engine ID Local Settings
The Engine ID is a unique identifier used to identify the SNMPv3 engine on the Switch.
Input the Engine ID then click Apply to apply the changes or click Default to change back to the default
value.
Figure 4.49 – Management > SNMP > SNMP Engine ID Local Settings
Management > SNMP > SNMP User Table Settings
The SNMP User Table Settings page allows user to manage the SNMP users that can access the Switch. It
allows user to set the Group, SNMP version, and authentication and encryption type for a user.
D-Link DMS-1100 Series User Manual
44
Figure 4.50 – Management > SNMP > SNMP User Table Settings
The fields that can be configured for SNMP User Table Settings are described below:
Item
Description
User Name
Enter a SNMP user name of up to 32 characters.
Group Name
Enter the SNMP group of the SNMP user.
SNMP Version
Select the SNMP version of the user. The options to choose are v1,
v2c and v3.
SNMP V3 Encryption
When selecting v3 in the SNMP Version drop-down list, this option is
available. Options to choose from are None, Password, and Key.
Auth-Protocol by Password
Select either MD5 or SHA to be the authentication protocol. Enter a
password for SNMPv3 encryption in the right column.
◆ MD5 – Select to use the HMAC-MD5-96 authentication level. This
field will require the user to enter a password.
◆ SHA - Select that the HMAC-SHA authentication protocol will be
used. This field will require the user to enter a password.
Priv-Protocol by Password
Select either None or DES56 and then enter a password for SNMPv3
encryption in the right column.
◆ None – Select to not use any authorization.
◆ DES56 – Select to use DES 56-bit encryption, based on the
CBC-DES (DES-56) standard. This field will require you to enter
a password.
Auth-Protocol by Key
Select either MD5 or SHA to be the authentication protocol. Enter a
key for SNMPv3 encryption in the right column.
◆ MD5 – Select to use the HMAC-MD5-96 authentication level. This
field will require the user to enter a key.
◆ SHA – Select to use the HMAC-SHA authentication protocol. This
field will require you to enter a key.
Priv-Protocol by Key
Select either None or DES56 and then enter a password for SNMPv3
encryption in the right column.
◆ None – Select to not use any authorization.
◆ DES56 – Select to use DES 56-bit encryption, based on the
CBC-DES (DES-56) standard. This field will require the user to
enter a key.
D-Link DMS-1100 Series User Manual
45
Table 4.29
Click Add to create a new SNMP user account or click Delete to remove any existing data.
Management > SNMP > SNMP Host Table Settings
The SNMP Host Table Settings page allows user to configure the SNMP trap recipients.
Figure 4.51 – Management > SNMP > SNMP Host Table Settings
The fields that can be configured for SNMP Host Table Settings are described below:
Item
Description
Host IPv4/IPv6 Address
Select IPv4 or IPv6 and specify the IP address of SNMP management
host.
User-based Security Model
Specify the SNMP version to be used to the management host. The
options are SNMPv1, SNMPv2C and SNMPv3.
Security Level
When selecting SNMPv3 in the User-based Security Model drop-
down list, this option is available.
◆ NoAuthNoPriv – Select to have no authorization and no
encryption of packets sent between the Switch and a remote
SNMP manager.
◆ AuthNoPriv – Select to require authorization, but with no
encryption of packets sent between the Switch and a remote
SNMP manager.
◆ AuthPriv – Select to require authorization, and packets sent
between the Switch and a remote SNMP manger will be
encrypted.
UDP Port (0-65535)
Enter the UDP port number. The default trap UDP port number is 162.
The range of UDP port numbers is from 0 to 65535.
Community String / SNMPv3
User Name
Enter the community string to be sent with the notification packet.
Table 4.30
Click Add to create a new SNMP host, Delete to remove an existing host.
Management > Web
The Web page allows user to configure Web settings on the Switch.
D-Link DMS-1100 Series User Manual
46
Figure 4.52 – Management > Telnet/Web
The fields that can be configured for Web are described below:
Item
Description
Port (1-65535)
Enter the TCP port number used for Telnet management of the Switch.
The standard TCP port for the HTTP protocol is 80.
Table 4.31
Click Apply to make the configurations take effect.
Management > Session Timeout
The Session Timeout page allows user to configure the session timeout on the Switch.
Figure 4.53 – Management > Session Timeout
The fields that can be configured for Session Timeout are described below:
Item
Description
Web Session Timeout (60-
36000)
Enter the time in seconds of the web session timeout. The range of
timeout is between 60 and 36000 seconds. Tick the Default check box
to use default value. The default is 180.
Table 4.32
Click Apply to make the configurations take effect.
Management > D-Link Discover Protocol Settings
The D-Link Discover Protocol Settings page allows user to configure and display D-Link Discovery Protocol
(DDP).
D-Link DMS-1100 Series User Manual
47
Figure 4.54 – Management > D-Link Discover Protocol Settings
The fields that can be configured for D-Link Discover Protocol Settings are described below:
Item
Description
DDP Global Settings
D-Link Discovery Protocol
State
Select the enable or disable the D-Link Discovery Protocol state.
Report Timer
Specify the interval in seconds between two consecutive DDP report
messages. Options to choose from are 30, 60, 90,120, and Never.
DDP Port Settings
From Port / To Port
Enter the appropriate port range used for the configuration.
State
Select to enable or disable the DDP port state.
Table 4.33
Click Apply to make the configurations take effect.
L2 Features > FDB > Static FDB > Unicast Static FDB
The Unicast Static FDB page allows user to view and configure the static unicast forwarding settings on the
Switch.
Figure 4.55 – L2 Features > FDB > Static FDB > Unicast Static FDB
Port / Drop: Allows the selection of the port number on which the MAC address entered resides. This option
could also drop the MAC address from the unicast static FDB. When selecting Port, select the switch unit
D-Link DMS-1100 Series User Manual
48
and port number.
VID (1-4094): Enter the VLAN ID on which the associated unicast MAC address resides.
MAC Address: Enter the MAC address to which packets will be statically forwarded or dropped. This must
be a unicast MAC address.
The fields that can be configured for Unicast Static FDB are described below:
Item
Description
Port / Drop
Allows the selection of the port number on which the MAC address
entered resides. This option could also drop the MAC address from the
unicast static FDB. When selecting Port, select the switch unit and port
number.
VID (1-4094)
Enter the VLAN ID on which the associated unicast MAC address
resides.
MAC Address
Enter the MAC address to which packets will be statically forwarded or
dropped. This must be a unicast MAC address.
Table 4.34
Click Apply to make the configurations take effect.
Click the Delete All button to delete all the entries found in the display table.
Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
L2 Features > FDB > Static FDB > Multicast Static FDB
The Multicast Static FDB page allows user to view and configure the static multicast forwarding settings on
the Switch.
Figure 4.56 – L2 Features > FDB > Static FDB > Multicast Static FDB
The fields that can be configured for Multicast Static FDB are described below:
Item
Description
From Port / To Port
Enter the appropriate port range used for the configuration.
VID (1-4094)
Enter the VLAN ID of the VLAN the corresponding MAC address
belongs to.
MAC Address
Enter the static destination MAC address of the multicast packets. This
must be a multicast MAC address. The format of the destination MAC
address is 01-XX-XX-XX-XX-XX.
Table 4.35
Click Apply to make the configurations take effect.
D-Link DMS-1100 Series User Manual
49
Click the Delete All button to remove all the entries.
Click the Delete button to remove the specific entry.
Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
L2 Features > FDB > MAC Address Table Settings
The MAC Address Table Settings page allows user to view and configure the MAC address table’s global
settings.
Figure 4.57 – L2 Features > FDB > MAC Address Table Settings – Global Setting
The fields that can be configured for MAC Address Table Settings are described below:
Item
Description
Aging Time
Enter the MAC address table’s aging time value. This value must be
between 10 and 410 seconds. Entering 0 will disable MAC address
aging. By default, this value is 300 seconds.
Aging Destination Hit
Select to enable or disable the aging destination hit function.
Table 4.36
Click Apply to make the configurations take effect.
After clicking the MAC Address Learning tab, the following page will appear.
Figure 4.58 – L2 Features > FDB > MAC Address Table Settings – MAC Address Learning
The fields that can be configured for MAC Address Table Settings are described below:
Item
Description
From Port / To Port
Enter the range of ports that will be used for this configuration.
State
Select to enable or disable the MAC address learning function on the
D-Link DMS-1100 Series User Manual
50
specified ports.
Table 4.37
Click Apply to make the configurations take effect.
L2 Features > FDB > MAC Address Table
The MAC Address Table page allows user to view the entries listed in the MAC address table.
Figure 4.59 – L2 Features > FDB > MAC Address Table
The fields that can be configured for MAC Address Table are described below:
Item
Description
Port
Select the port that will be used for this configuration.
VID (1-4094)
Enter the VLAN ID that will be used for this configuration.
MAC Address
Enter the MAC address that will be used for this configuration.
Table 4.38
Click the Find button to locate a specific entry based on the information entered.
Click the Clear Dynamic by Port button to clear the dynamic MAC address listed on the corresponding port.
Click the Clear Dynamic by VLAN button to clear the dynamic MAC address listed on the corresponding
VLAN.
Click the Clear Dynamic by MAC button to clear the dynamic MAC address entered.
Click the Find button to locate a specific entry based on the information entered.
Click the Clear All button to clear all dynamic MAC addresses.
Click the View All button to display all the MAC addresses recorded in the MAC address table.
L2 Features > 802.1Q VLAN
The 802.1Q VLAN page allows user to view and configure the VLAN settings on this switch.
Figure 4.60 – L2 Features > 802.1Q VLAN
D-Link DMS-1100 Series User Manual
51
The fields that can be configured for 802.1Q VLAN are described below:
Item
Description
802.1Q VLAN
VID List
Enter the VLAN ID list that will be created.
Find VLAN
VID (1-4094)
Enter the VLAN ID to be displayed.
Table 4.39
Click Apply to make the configurations take effect.
Click the Delete button to remove the specific entry.
Click the Find button to locate a specific entry based on the information entered.
Click the View All button to locate all the entries.
Click the Edit button to re-configure the specific entry.
Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
L2 Features > Asymmetric VLAN
The Asymmetric VLAN page allows user to configure the asymmetric VLAN function on this switch.
Figure 4.61 – L2 Features > Asymmetric VLAN
The fields that can be configured for MAC Address Table are described below:
Item
Description
Asymmetric VLAN State
Select to enable or disable the Asymmetric VLAN function.
Table 4.40
Click Apply to make the configurations take effect.
L2 Features > VLAN Interface
The VLAN Interface page allows user to view and configure the VLAN interface settings on this switch.
Figure 4.62 – L2 Features > VLAN Interface
D-Link DMS-1100 Series User Manual
52
Click the VLAN Detail button to view more detailed information about the VLAN on the specific interface.
Click the Edit button to re-configure the specific entry.
After clicking the VLAN Detail button, the following page will appear:
Figure 4.63 – L2 Features > VLAN Interface – VLAN Detail
After clicking the Edit button, the following window will appear. This is a dynamic window that will change
when a different VLAN Mode is selected. When Access was selected as the VLAN Mode, the following
page will appear.
Figure 4.64 – L2 Features > VLAN Interface – VLAN Detail
The fields that can be configured for VLAN Interface are described below:
Item
Description
Port
Display the VLAN port number.
VLAN Mode
Select the VLAN mode option. Options to choose from are Access,
Hybrid, and Trunk.
Acceptable Frame Type
Select the acceptable frame type behavior option. Options to choose
from are Tagged Only, Untagged Only, and Admit All.
Ingress Checking
Select to enable or disable the ingress checking function.
Native VLAN
Tick the option to enable the native VLAN function.
VID (1-4094)
After ticking the Native VLAN check box, this option will be available.
Enter the VLAN ID used for this configuration. This value must be
between 1 and 4094.
Action
Select the action that will be taken here. Options to choose from are
Add, Remove, Tagged, and Untagged.
D-Link DMS-1100 Series User Manual
53
Add Mode
Select whether to add an Untagged or Tagged parameters.
Allowed VLAN Range
Enter the allowed VLAN range information.
Clone
Tick the Clone check box to copy the configuration to specified ports.
From Port / To Port
Copy the configuration of VLAN interface for specified port ranges.
Table 4.41
Click Apply to make the configurations take effect.
Click the Back button to return to the previous page.
L2 Features > Auto Surveillance VLAN > Auto Surveillance Properties
The Auto Surveillance Properties page is used to configure the auto surveillance VLAN global settings and
display the ports surveillance VLAN information.
Figure 4.65 – L2 Features > Auto Surveillance VLAN > Auto Surveillance Properties
The fields that can be configured for Auto Surveillance Properties are described below:
Item
Description
Global Settings
Surveillance VLAN
Specify to enable or disable the surveillance VLAN state.
Surveillance VLAN ID
Enter the surveillance VLAN ID. The range is from 1 to 4094.
Surveillance VLAN CoS
Specify the priority of the surveillance VLAN from 0 to 7.
Aging Time (1-65535)
Specify the aging time of the surveillance VLAN. The range is from 1 to
65535 minutes. The default value is 720 minutes. The aging time is
used to remove a port from surveillance VLAN if the port is an
automatic surveillance VLAN member. When the last surveillance
device stops sending traffic and the MAC address of this surveillance
D-Link DMS-1100 Series User Manual
54
device is aged out, the surveillance VLAN aging timer will be started.
The port will be removed from the surveillance VLAN after expiration of
surveillance VLAN aging timer. If the surveillance traffic resumes
during the aging time, the aging counter will be reset and the timer will
stop.
Surveillance VLAN Log
Specify to enable or disable the Surveillance VLAN log feature.
Port Settings
From Port/To Port
Specify the port range used for the configuration.
State
Specify to enable or disable the state of the port.
Table 4.42
Click Apply to make the configurations take effect.
L2 Features > Auto Surveillance VLAN > MAC Settings and Surveillance Device
The MAC Settings and Surveillance Device page is used to configure the user-defined surveillance device
OUI and display the surveillance VLAN information.
Figure 4.66 – L2 Features > Auto Surveillance VLAN > MAC Settings and Surveillance Device
The fields that can be configured for MAC Settings and Surveillance Device are described below:
Item
Description
Component Type
Specify the surveillance component type. Option to choose from are
Vms, VmsClient, VideoEncoder, NetworkStorage and Other.
Description
Enter the description for the user-defined OUI with a maximum of 32
characters.
MAC Address
Enter the description for the user-defined OUI with a maximum of 32
characters.
Mask
Enter the OUI MAC address matching bitmask.
Table 4.43
Click the Apply button to accept the changes made.
Click the Delete button to remove the specified entry.
After click the Auto Surveillance VLAN Summary tab, the following page will appear.
D-Link DMS-1100 Series User Manual
55
Figure 4.67 – L2 Features > Auto Surveillance VLAN > MAC Settings and Surveillance Device
L2 Features > Voice VLAN > Voice VLAN Global
The Voice VLAN is a VLAN used to carry voice traffic from an IP phone. As the sound quality of Voice over
IP, is sensitive to delay Quality of service (QoS) for voice traffic should be configured to ensure that voice
traffic is handled with a higher priority.
The switches determine whether a received packet is a voice packet by checking its source MAC address. If
the source MAC addresses of a packet complies with the organizationally unique identifier (OUI) addresses
configured by the system, the packets are determined as voice packets and transmitted in voice VLAN.
Figure 4.68 – L2 Features > Voice VLAN > Voice VLAN Global Settings
The fields that can be configured for Voice VLAN Global Settings are described below:
Item
Description
Voice VLAN State
Select to enable or disable Voice VLAN.
VLAN ID (1-4094)
Enter the voice VLAN ID. The value is range from 1 to 4094.
Voice VLAN CoS
Specify the priority of the voice VLAN from 0 to 7.
Aging Time
Enter the aging time of surveillance VLAN. The range is from 1 to
65535 minutes. The default value is 720 minutes. The aging time is
used to remove a port from voice VLAN if the port is an automatic
VLAN member. When the last voice device stops sending traffic and
the MAC address of this voice device is aged out, the voice VLAN
aging timer will be started. The port will be removed from the voice
VLAN after expiration of voice VLAN aging timer. If the voice traffic
resumes during the aging time, the aging counter will be reset and the
timer will stop.
Table 4.44
Click the Apply button to accept the changes made.
L2 Features > Voice VLAN > Voice VLAN Port
The Voice VLAN Port page is used to show the ports voice VLAN information.
D-Link DMS-1100 Series User Manual
56
Figure 4.69 – L2 Features > Voice VLAN > Voice VLAN Port
The fields that can be configured for Voice VLAN Port are described below:
Item
Description
From Port / To Port
Select the appropriate port range used for the configuration.
State
Specify to enable or disable the state of the port.
Mode
Specify the mode of the port. Options to choose from are Auto
Untagged, Auto Tagged, and Manual.
Table 4.45
Click the Apply button to accept the changes made.
L2 Features > Voice VLAN > Voice VLAN OUI
The Voice VLAN OUI page is used to configure the user-defined voice traffic’s OUI. The OUI is used to
identify voice traffic. There are a number of pre-defined OUIs. The user can further define the user-defined
OUIs if needed. The user-defined OUI cannot be the same as the pre-defined OUI.
Figure 4.70 – L2 Features > Voice VLAN > Voice VLAN OUI
The fields that can be configured for Voice VLAN OUI are described below:
Item
Description
D-Link DMS-1100 Series User Manual
57
OUI Address
Specify the OUI MAC address.
Mask
Specify the OUI MAC address matching bitmask.
Description
Enter the description for the user-defined OUI with a maximum of 32
characters.
Table 4.46
Click the Apply button to accept the changes made.
Click the Delete button to remove the specified entry.
L2 Features > Voice VLAN > Voice VLAN Device
The Voice VLAN Device page is used to show voice devices that are connected to the Switch. The Start
Time is the time when the device was detected on the port and the Status displays the voice VLAN status of
the port.
Figure 4.71 – L2 Features > Voice VLAN > Voice VLAN Device
L2 Features > Voice VLAN > Voice VLAN LLDP-MED Device
The page displays the Voice VLAN LLDP-MED voice devices connected to the Switch.
Figure 4.72 – L2 Features > Voice VLAN > Voice VLAN LLDP-MED Device
L2 Features > STP > STP Global Settings
The Switch implements three versions of the Spanning Tree Protocol: Rapid Spanning Tree Protocol (RSTP)
as defined by IEEE 802.1w, a version compatible with the IEEE 802.1D STP and Multiple Spanning Tree
Protocol (MSTP), as defined by IEEE802.1. RSTP can operate with legacy equipment implementing IEEE
802.1D, however the advantages of using RSTP will be lost.
The Rapid Spanning Tree Protocol (RSTP) evolved from the 802.1D STP standard and was developed in
order to overcome some of the limitations of STP that impede the function of some recent switching
innovations. The basic function and much of the terminology is the same and most of the settings configured
for STP are also used for RSTP. This section introduces some new Spanning Tree concepts and illustrates
the main differences between the two protocols.
The IEEE 802.1 Multiple Spanning Tree (MSTP) provides various load balancing techniques by allowing
multiple VLANs to be mapped to a single spanning tree instance, providing multiple pathways across the
network. For example, while port A is blocked in one STP instance, the same port can be placed in the
Forwarding state in another STP instance.
D-Link DMS-1100 Series User Manual
58
By default, Rapid Spanning Tree is disabled. If enabled, the Switch will listen for Bridge Protocol Data Unit
(BPDU) packets and its accompanying Hello packet. The BPDU packets are sent even if a BPDU packet is
not received. Therefore, each link between bridges is sensitive to the status of the link. Ultimately this
difference results in faster detection of failed links, and therefore faster topology adjustment.
By default Multiple Spanning Tree is enabled. It will tag BPDU packets to receiving devices and distinguish
spanning tree instances, spanning tree regions and the VLANs associated with them.
After enabling STP, configure the STP Global Settings (shown below).
Figure 4.73 – L2 Features > STP > STP Global Settings
The fields that can be configured for STP Global Settings are described below:
Item
Description
STP State
STP State
Select to enable or disable the Spanning Tree Protocol.
STP Traps
STP New Root Trap
Select to enable or disable the STP new root trap option.
STP Topology Change Trap
Select to enable or disable the STP topology change trap option.
STP Mode
STP Mode
Select the STP mode. The options to choose from are MSTP, RSTP
and STP.
STP Priority
Priority (0-61440)
This value is between 0 and 61440. By default, this value is 32768.
The lower the value, the higher the priority.
STP Configuration
Bridge Max Age (6-40)
Enter the bridge’s maximum age value here. This value must be
between 6 and 40 seconds. By default, this value is 20 seconds. The
maximum age value may be set to ensure that old information does not
endlessly circulate throughout the network. Set by the root bridge, this
D-Link DMS-1100 Series User Manual
59
value ensures that the Switch has spanning tree configuration
consistent with other devices on the LAN.
Bridge Forward Time (4-30)
Enter the bridge’s forwarding time value. This value must be between 4
and 30 seconds. By default, this value is 15 seconds. Any port on the
Switch spends this time in the listening state while moving from the
blocking state to the forwarding state.
Max Hops (1-40)
Enter the maximum number of hops that are allowed. This value must
be between 1 and 40 hops. By default, this value is 20 hops. This
value is used to set the number of hops between devices in a spanning
tree region before the BPDU packet sent by the Switch will is
discarded. Each switch on the hop count will reduce the hop count by
one until the value reaches zero. The Switch will then discard the
BDPU packet and the information held for the port will age out.
Bridge Hello Time (0-2)
After selecting RSTP/STP as the STP Mode, this parameter will be
available. Enter the bridge’s hello time value here. This value must be
between 1 and 2 seconds. By default, this value is 2 seconds. This is
the interval between two transmissions of BPDU packets sent by the
Root Bridge to all switches. This field will only appear when STP or
RSTP is selected for the STP Version. For MSTP, the Hello Time must
be set on a port by port basis.
TX Hop Count (1-10)
Enter the transmit hold count value. This value must be between 1 and
10. The default value is 6. This value is used to set the maximum
number of Hello packets transmitted per interval.
Table 4.47
Click Apply to make the configurations take effect.
L2 Features > STP > STP Port Settings
In addition to setting spanning tree parameters for use on the switch level, the Switch allows for the
configuration of STP on a port level Groups of ports can be configured in a port group, each of which can
have its own spanning tree instance and configuration settings.
Port level spanning tree works in the same way as switch level spanning tree, but the root bridge is replaced
with a root port. A root port in the group, which is elected based on port priority and port cost, and is the
connection to the network for the group. Redundant links will be blocked, just as redundant links are blocked
on the switch level.
The STP on the switch level blocks redundant links between switches (and similar network devices). The
port level STP will block redundant links within an STP group.
D-Link DMS-1100 Series User Manual
60
Figure 4.74 – L2 Features > STP > STP Port Settings
The fields that can be configured for STP Port Settings are described below:
Item
Description
From Port/To Port
Enter a consecutive group of ports to be configured starting with the
selected port.
Cost
This is the STP port cost, which is used to calculate the spanning tree
topology. It represents the relative interface bandwidth and is the
desirability of the link. The port cost can be set automatically or set
manually as a metric value. The default value is 0 (auto).
0 (auto): Setting 0 for the external cost will automatically set the
speed for forwarding packets to the specified port(s) in the list for
optimal efficiency. Default port cost: 100Mbps port = 200000.
Gigabit port = 20000.
Value 1-200000000: Define a value between 1 and 200000000 to
determine the external cost. The lower the number, the greater
the probability the port will be chosen to forward packets.
State
Select to enable or disable port based STP. It will be selectable after
STP is enabled globally on the Switch.
Guard Root
Select to enable or disable the guard root function.
Link Type
Select the link type option. The options to choose from are Auto, P2P,
and Shared. A full-duplex port is considered to have a point-to-point
(P2P) connection. A half-duplex port is considered to have a Shared
connection. The port cannot rapidly transition to the forwarding state if
the link type is set to Shared. By default this option is Auto.
Port Fast
Select the port fast option. The options are Disabled and Edge. In the
Disabled mode, the port will always be in the non-port fast state. It will
wait for the forward-time delay to change to the forwarding state. In the
Edge mode, the port will directly change to the forwarding state without
waiting for the forward-time delay. If the interface receives a BPDU, its
operation state changes to the non-port fast state.
D-Link DMS-1100 Series User Manual
61
TCN Filter
Select to enable or disable the TCN filter option. Enabling TCN filtering
on a port is useful for connecting to an external network, which may not
be under full control of the administrator. When a port is set to the TCN
filter mode, the topology change event received by the port will be
ignored. By default, this option is disabled.
BPDU Forward
Bridges use Bridge Protocol Data Units (BPDUs) in the operation of
spanning tree, BPDU. Forwarding is useful when a bridge
interconnects two regions, with each region requiring a separate
spanning tree. BPDU filtering functions only when STP is disabled
either globally or on a single interface. The possible field values are:
Disabled: BPDU filtering is enabled on the port.
Enabled: BPDU forwarding is enabled on the port (STP must be
disabled).
Priority
Select the priority of each port. Selectable range is from 0 to 240, and
the default setting is 128. The lower the number, the greater the
probability the port will be chosen as a root port.
Hello Time
The interval between two transmissions of BPDU packets sent by the
Root Bridge to indicate to all other switches that it is indeed the Root
Bridge. The default value is 2.
Table 4.48
Click Apply to make the configurations take effect.
L2 Features > STP > MST Configuration Identification
Multiple Spanning Tree (MSTP) provides various load balancing scenarios by allowing multiple VLANs to be
mapped to a single spanning tree instance, providing multiple pathways across the network. For example,
while port A is blocked in one STP instance, the same port can be placed in the Forwarding state in another
STP instance.
The MST Configuration Identification page is for defining global MSTP settings, including region names,
MSTP revision level.
Figure 4.75 – L2 Features > STP > MST Configuration Identification
The fields that can be configured for MST Configuration Identification are described below:
Item
Description
MST Configuration Identification
Configuration Name
Enter a name set on the switch to uniquely identify the MSTI (multiple
D-Link DMS-1100 Series User Manual
62
spanning tree instance). If a configuration name is not set, this field
shows the MAC address of the device running MSTP.
Revision Level(0 - 65535)
This value, together with the configuration name and identical VLANs
mapped for STP instance IDs identifies the MST region configured on
the switch.
Instance ID Settings
Instance ID (1 - 64)
Enter the MSTI ID associated with the VID List. The possible field
range is 1-64.
Action
Action: The possible values are:
Add VID - Indicates that the edit type is add.
Remove VID - Indicates that the edit type is removed.
VID List
Enter the VID range from configured VLANs set on the Switch.
Table 4.49
Click Apply to define the configuration name and revision level.
Click the Edit to modify the setting of VID or click Delete to remove it.
L2 Features > STP > STP Instance
The STP Instance Settings page display MSTIs currently set on the Switch and allows users to change the
Priority of the MSTPs.
Figure 4.76 – L2 Features > STP > STP Instance
Click the Edit button to re-configure the specific entry.
L2 Features > STP > MSTP Port Information
The MSTP Port Information page allows user to configure the MSTP Interface settings.
Figure 4.77 – L2 Features > STP > MSTP Port Information
The fields that can be configured for MSTP Port Information are described below:
D-Link DMS-1100 Series User Manual
63
Item
Description
Port
Select the port to be fined.
Table 4.50
Click the Clear Detected Protocol button to clear the detected protocol settings for the port selected.
Click Find to search the MSTP port information.
Click the Edit button to re-configure the specific entry.
L2 Features > ERPS(G.8032) > ERPS
ERPS (Ethernet Ring Protection Switching) is the first industry standard (ITU-T G.8032) for Ethernet ring
protection switching. It is achieved by integrating mature Ethernet Operations, Administration, and
Maintenance (OAM)* functions and a simple automatic protection switching (APS) protocol for Ethernet ring
networks. ERPS provides sub-50ms failover for Ethernet traffic in a ring topology. It ensures that there are no
loops formed at the Ethernet layer.
One link within a ring, the ring Protection Link (RPL), will be blocked to avoid a Layer 2 loop. When there is a
failure, protection switching blocks the failed link and unblocks the RPL. When the failure clears, protection
switching blocks the RPL again and unblocks the link on which the failure is cleared.
The ERPS page allows user to configure the ERPS instance and profile configuration of the Switch.
Figure 4.78 – L2 Features > ERPS(G.8032) > ERPS
The fields that can be configured for ERPS are described below:
Item
Description
Instance ID (1-16)
Specify the Instance ID to be created.
Table 4.51
Click Apply to make the configurations take effect.
NOTE: STP and LBD should be disabled on the
ring ports before enabling ERPS.
Enter Instance ID 1 and click Apply to create ERPS physical ring. Then the following page will be displayed.
Figure 4.79 – L2 Features > ERPS(G.8032) > ERPS - Create
D-Link DMS-1100 Series User Manual
64
Click Edit Instance button to modify the ERP instance, click Show Status button to display the ERPS
physical ring’s status information, or click Delete button to remove the Ethernet instance.
Click Edit Instance to modify the Ethernet Instance configuration:
Figure 4.80 – L2 Features > ERPS(G.8032) > ERPS – Edit Instance
The fields that can be configured for edit ERPS are described below:
Item
Description
Ethernet Ring Name
Enter the Ethernet ring name for the specified instance.
Sub Ring Name
Enter the sub ring name of a physical ring.
Port0
Specifies the port as the first ring port and also specifies the virtual port
channel used.
Port1
Specifies the port as the second ring port and also specifies the virtual
port channel used.
Description
Enter the description for the specified instance.
R-APS Channel VLAN (1-4094)
Specifies the R-APS channel of ERP instance. The range is between 1
and 4094.
Inclusion VLAN List
Specifies to add or delete the inclusion VLAN group. The VLANs
specified here will be protected by the ERP mechanism.
MEL(0-7)
Specifies the ring MEL of the R-APS function. The default ring MEL is
1.
Profile Name
Specifies the profile name of Ethernet Instance.
RPL Port
Specifies the RPL port used. Options to choose from are Port0, Port1,
and None.
RPL Owner
Specifies to enable or disable the RPL owner node.
Active
Specifies enable or disable to active this ERP instance.
Table 4.52
Click Apply to make the configurations take effect.
Click the Back button to return to the previous page.
D-Link DMS-1100 Series User Manual
65
Click Show Status button to display the ERPS status information.
Figure 4.81 – L2 Features > ERPS(G.8032) > ERPS – Show Status
L2 Features > ERPS(G.8032) > ERPS Profile
The ERPS Profile page allows user to configure the ERPS profile information of the Switch.
Figure 4.82 – L2 Features > ERPS(G.8032) > ERPS Profile
The fields that can be configured for ERPS Profile are described below:
Item
Description
Profile Name
Specify the profile name to be created on the Switch.
Table 4.53
Click Apply to make the configurations take effect.
Click the Delete button to remove the profile.
Enter Profile Name and click Apply button to associate the G.8032 profile with the ERP instance created.
Figure 4.83 – L2 Features > ERPS(G.8032) > ERPS Profile - created
D-Link DMS-1100 Series User Manual
66
Click Edit button to configure the Ethernet Profile settings:
Figure 4.84 – L2 Features > ERPS(G.8032) > ERPS Profile - Edit
The fields that can be configured for edit ERPS Profile are described below:
Item
Description
Revertive
Specifies whether to enable or disable to the original state after a
failure, for example, when the RPL was blocked.
Guard Time (10-2000)
Specifies the guard time of the R-APS function. The value is between
10 and 2000 milliseconds. The default guard time is 500 milliseconds.
Hold-Off Timer (0-10000)
Specifies the hold-off time of the R-APS function. The value is between
0 and 10000 milliseconds. The default hold-off time is 0 milliseconds.
WTR Timer (1-12)
Specifies the WTR time of the R-APS function. The value is between 1
and 12 minutes. The default WTR time is 5 minutes.
Table 4.54
Click Apply to make the configurations take effect.
Click the Back button to return to the previous page.
L2 Features > Loopback Detection
The Loopback Detection function is used to detect the loop created by a specific port while Spanning Tree
Protocol (STP) is not enabled in the network, especially when the down links are hubs or unmanaged
switches. The Switch will automatically shut down the port and send a log to the administrator. The Loopback
Detection port will be unlocked when the Loopback Detection Recover Time times out. The Loopback
Detection function can be implemented on a range of ports at a time. You may enable or disable this function
using the pull-down menu.
D-Link DMS-1100 Series User Manual
67
Figure 4.85 – L2 Features > Loopback Detection Settings
The fields that can be configured for Loopback Detection Settings are described below:
Item
Description
Loopback Detection Global Settings
Loopback Detection State
Enable or disable loopback detection. The default is disabled.
Mode
Select either Port-based or VLAN-based loopback detection.
Enabled VLAN ID List
Enter the VLAN ID for loopback detection. This only takes effect when
VLAN-based is selected in the Mode drop-down list.
Interval (1-32767)
Set a Loop Detection Interval between 1 and 32767 seconds. The
default is 2 seconds.
Trap State
Select to enable or disable the loopback detection trap state.
Action
Select Shut-down or None for loopback detection.
Loopback Detection Port Settings
From Port / To Port
Enter a consecutive group of ports to be configured starting with the
selected port.
From Port / To Port
Use the drop-down menu to toggle between Enabled and Disabled.
Default is disabled.
Table 4.55
Click Apply to make the configurations take effect.
L2 Features > Link Aggregation
The Link Aggregation page allows user to view and configure the link aggregation settings.
D-Link DMS-1100 Series User Manual
68
Figure 4.86 – L2 Features > Link Aggregation
The fields that can be configured for Link Aggregation are described below:
Item
Description
Ling Aggregation Settings
System Priority (1-65535)
Enter the system’s priority value. This must be between 1 and 65535.
By default, the value is 32768. The system priority determines which
ports can join a port-channel and which ports are put in stand-alone
mode. The lower value has a higher priority. If two or more ports have
the same priority, the port number determines the priority.
Load Balance Algorithm
Specify the load balancing algorithm that will be used. Options to
choose from are: Source MAC, Destination MAC, Source
Destination MAC, Source IP, Destination IP, and Source
Destination IP. By default, this option is Source MAC.
System ID: The System ID information.
Channel Group Information
From Port / To Port
Select the appropriate port range used for the configuration.
Group ID: Enter the channel-group number. This value must be
between 1 and 32. The system will automatically create the port-
channel when a physical port first joins a channel-group. An interface
can only join one channel-group.
Mode
Select either On, Active, or Passive. If you selected On, the channel-
group type is static. If Active or Passive is selected, the channel-group
type is LACP. A channel-group can only consist of either static
members or LACP members. Once the type of channel-group has
been determined, other types of interfaces cannot join the channel-
group.
Table 4.56
Click Apply to make the configurations take effect.
Click the Add button to add a new entry based on the information entered.
Click the Delete Member Port button to remove the specific member port.
Click the Delete Channel button to remove the specific entry.
Click the Channel Detail button to view more detailed information about the channel.
D-Link DMS-1100 Series User Manual
69
L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Settings
With Internet Group Management Protocol (IGMP) snooping, the DMS-1100 Series Switch can make
intelligent multicast forwarding decisions by examining the contents of each frame’s Layer 2 MAC header.
IGMP snooping can help reduce cluttered traffic on the LAN. With IGMP snooping enabled globally, the
DMS-1100 Series Switch will forward multicast traffic only to connections that have group members attached.
The settings of IGMP snooping is set by each VLAN individually.
Figure 4.87 – L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Settings
The fields that can be configured for IGMP Snooping Settings are described below:
Item
Description
Global Settings
Global State
Select to enable or disable the IGMP Snooping global state.
VLAN Status Settings
VID (1-4094)
Enter the VLAN ID and select to enable or disable the IGMP snooping
on the VLAN.
IGMP Snooping Table
VID (1-4094)
Enter the VLAN ID between 1 and 4094.
Table 4.57
Click Apply to make the configurations take effect.
Click the Find button to display a specific entry based on the information entered.
Click the Find All button to display all the entries.
Click the Show Detail button to display the detail information of the specified VLAN.
Click the Edit button to re-configure the specific entry.
Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
After clicking the Show Detail button, the following window will appear:
D-Link DMS-1100 Series User Manual
70
Figure 4.88 – L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping – Show Detail
Click the Modify button to edit the information in the following window:
Figure 4.89 L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping – Modify
The fields that can be configured for edit IGMP Snooping are described below:
Item
Description
Fast Leave
Select to enable or disable the IGMP snooping fast leave function.
Querier State
Select to enable or disable the querier state.
Query Version
Select the general query packet version sent by the IGMP snooping
querier.
Query Interval (1-31744)
Enter the interval at which the IGMP snooping querier sends IGMP
general query messages periodically.
Max. Response Time (1-25)
Enter the interval at which the IGMP snooping querier sends IGMP
general query messages periodically.
Robustness Value (1-7)
Enter the robustness variable used in IGMP snooping.
Last Member Query Interval
Enter the interval at which the IGMP snooping querier sends IGMP
D-Link DMS-1100 Series User Manual
71
(1-25)
group-specific or group-source-specific query messages.
Table 4.58
Click Apply to make the configurations take effect.
L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Groups Settings
The IGMP snooping Groups Settings page allows user to configure and view the IGMP snooping static group,
and view IGMP snooping group.
Figure 4.90 – L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Group Settings
The fields that can be configured for edit IGMP Snooping Group Settings are described below:
Item
Description
VID (1-4094)
Enter the VLAN ID.
Group Address
Enter the IP multicast group address.
From Port / To Port
Select the range of ports to be configured.
Table 4.59
Click Apply to make the configurations take effect.
Click the Delete button to remove the specified entry.
Click the Find button to locate a specific entry based on the information entered.
Click the Find All button to view all the entries.
Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
The fields that can be configured for IGMP Snooping Groups Table are described below:
Item
Description
VID (1-4094)
Specify the VLAN ID.
Group Address
Enter the IP multicast group address.
Table 4.60
Click the Find button to locate a specific entry based on the information entered.
D-Link DMS-1100 Series User Manual
72
Click the Find All button to view all the entries.
L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Mrouter Settings
The IGMP Snooping Mrouter Settings page allows user to configure interfaces as multicast router ports or
ports that cannot be multicast router ports on the Switch.
Figure 4.91 – L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Mrouter Settings
The fields that can be configured for IGMP Snooping Mrouter Settings are displayed below:
Item
Description
VID (1-4094)
Enter the VLAN ID in the range 1 to 4094.
Configuration
Select the port configuration type.
◆ Port: Select to configure the port as a static multicast router port.
◆ Forbidden Port: Select to configure the port as a port that
cannot be a static multicast router port.
From Port / To Port
Select the range of ports to be configured.
Table 4.61
Click Apply to make the configurations take effect.
Click the Delete button to remove the specified entry.
The fields that can be configured for IGMP Snooping Mrouter Table are displayed below:
Item
Description
VID (1-4094)
Enter the VLAN ID to be searched.
Table 4.62
Click the Find button to locate a specific entry based on the information entered.
Click the Find All button to view all the entries.
Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Statistics Settings
The IGMP Snooping Statistics Settings page allows user to clear and display the IGMP snooping related
statistics.
D-Link DMS-1100 Series User Manual
73
Figure 4.92 – L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Statistics Settings
The fields that can be configured for IGMP Snooping Statistics Settings are displayed below:
Item
Description
Statistics
Select the interface to be cleared. The options are All and VLAN.
VID (1-4094)
Enter the VLAN ID.
Table 4.63
Click the Clear button to clear the IGMP snooping related statistics.
The fields that can be configured for IGMP Snooping Statistics Table are displayed below:
Item
Description
Find Type
Select the interface to be searched. The options are VLAN and Port.
VID (1-4094)
Enter the VLAN ID.
Table 4.64
Click the Find button to locate a specific entry based on the information entered.
Click the Find All button to view all the entries.
L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Setting
The MLD Snooping Settings page allows user to configure the MLD snooping settings.
Figure 4.93 – L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Setting
D-Link DMS-1100 Series User Manual
74
The fields that can be configured for MLD Snooping Settings are described below:
Item
Description
Global Settings
Global State
Select to enable or disable the MLD Snooping state.
VLAN Status Settings
VID (1-4094)
Enter the VLAN ID and select to enable or disable MLD snooping on
the VLAN.
MLD Snooping Table
VID (1-4094)
Enter the VLAN ID to be searched.
Table 4.65
Click Apply to make the configurations take effect.
Click the Find button to locate a specific entry based on the information entered.
Click the Find All button to view all the entries.
Click the Show Detail button to see the detail information of the specific VLAN.
Click the Edit button to re-configure the specific entry.
After clicking the Show Detail button, the following window will appear.
Figure 4.94 – L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Setting – Show Detail
The window displays the detail information about MLD snooping VLAN. Click the Modify button to edit the
information in the following window.
After clicking the Edit button in MLD Snooping Settings window, the following window will appear.
D-Link DMS-1100 Series User Manual
75
Figure 4.95 – L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Setting – Edit
The fields that can be configured for MLD Snooping Settings are displayed below:
Item
Description
Fast Leave
Select to enable or disable the MLD snooping fast leave function.
Querier State
Select to enable or disable the querier state.
Query Version
Select the general query packet version sent by the MLD snooping
querier.
Query Interval (1-31744)
Enter the interval at which the MLD snooping querier sends MLD
general query messages periodically.
Max. Response Time (1-25)
Enter the maximum response time, in seconds, advertised in MLD
snooping queries. The range is 1 to 25.
Robustness Value (1-7)
Enter the robustness variable used in MLD snooping.
Last Member Query Interval
(1-25)
Enter the interval at which the MLD snooping querier sends MLD
group-specific or group-source-specific (channel) query messages.
Table 4.66
Click Apply to make the configurations take effect.
L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Groups Settings
The MLD Snooping Groups Settings page allows user to configure and view the MLD snooping static group,
and view MLD snooping group.
D-Link DMS-1100 Series User Manual
76
Figure 4.96 – L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Group Settings
The fields that can be configured for MLD Snooping Group Settings are displayed below:
Item
Description
VID (1-4094)
Enter the VLAN ID.
Group Address
Enter the IP multicast group address.
From Port / To Port
Select the range of ports to be configured.
Table 4.67
Click Apply to make the configurations take effect.
Click the Delete button to remove the specified entry.
Click the Find button to locate a specific entry based on the information entered.
Click the Find All button to view all the entries.
Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
The fields that can be configured for the MLD Snooping Groups Table are described below:
Item
Description
VID (1-4094)
Enter the VLAN ID.
Group Address
Enter the IP multicast group address.
From Port / To Port
Select the range of ports to be configured.
Table 4.68
Click the Find Snooping button to locate a specific entry based on the information entered.
Click the Find All Snooping button to view all the entries.
L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Mrouter Settings
The MLD Snooping Mrouter Settings page allows user to configure the interfaces as router ports or ports that
cannot be multicast router ports on the Switch.
D-Link DMS-1100 Series User Manual
77
Figure 4.97 – L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Mrouter Settings
The fields that can be configured for the MLD Snooping Mrouter Table are described below:
Item
Description
VID (1-4094)
Enter the VLAN ID.
Configuration
Select the port configuration type.
◆ Port: Select to configure the port as being connected to a
multicast-enabled router.
From Port / To Port
Select the range of ports to be configured.
Table 4.69
Click Apply to make the configurations take effect.
Click the Delete button to remove the specified entry.
Click the Find button to locate a specific entry based on the information entered.
Click the Find All button to view all the entries.
Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Statistics Settings
The MLD Snooping Statistics Settings page allows user to clear and display the MLD snooping related
statistics.
Figure 4.98 – L2 Features > L2 Multicast Control > MLD Snooping > MLD Snooping Statistics Settings
The fields that can be configured for the MLD Snooping Statistics Settings are described below:
D-Link DMS-1100 Series User Manual
78
Item
Description
Statistics
Select the type of statistics to display. Available options are All and
VLAN.
VID (1-4094)
Enter the VLAN ID to be specified.
Table 4.70
Click the Clear button to remove the entries.
The fields that can be configured to display the MLD Snooping Statistics Table are described below:
Item
Description
Find Type
Select the type to find the statistics table.
VID (1-4094)
Enter the VLAN ID to be displayed.
Table 4.71
Click the Find button to locate a specific entry based on the information entered.
Click the Find All button to view all the entries.
L2 Features > LLDP > LLDP Global Settings
Link Layer Discovery Protocol (LLDP) is and IEEE 802.1AB standards-compliant method for switches to
advertise themselves to neighbor devices, as well as to learn about neighbor LLDP devices. SNMP utilities
can learn the network topology by obtaining the MIB information for each LLDP device. The LLDP function is
enabled by default.
Figure 4.99 – L2 Features > LLDP > LLDP Global Settings
The fields that can be configured for LLDP Global Settings are described below:
D-Link DMS-1100 Series User Manual
79
Item
Description
LLDP Global Settings
LLDP State
Select to enable or disable LLDP globally on the Switch. With this
enabled, the Switch will transmit receive and process LLDP packets.
LLDP Forward State
Select to enable or disable LLDP forward state. When the LLDP State
is disabled and LLDP Forward Sate is enabled, the received LLDPDU
packet will be forwarded.
LLDP Trap Sate
Select to enable or disable the LLDP trap state.
LLDP-MED Trap State
Select to enable or disable the LLDP-MED trap state.
LLDP-MED Configuration
Fast Start Repeat Count (1-10)
Enter the LLDP-MED fast start repeat count value. This value must be
between 1 and 10.
LLDP Configurations
Message TX Interval (5-32768)
This parameter indicates the interval at which LLDP frames are
transmitted on behalf of this LLDP agent. The default value is 30
seconds.
Message TX Hold Multiplier (2-
10)
This parameter is a multiplier that determines the actual TTL value
used in an LLDPDU. The default value is 4.
LLDP ReInit Delay (1-10)
This parameter indicates the amount of delay from the time
adminStatus becomes disabled until re-initialization is attempted. The
default value is 2 seconds.
LLDP TX Delay (1-8192)
This parameter indicates the delay between successive LLDP frame
transmissions initiated by value or status changes in the LLDP local
systems MIB. The value for txDelay is set by the following range
formula: 1 < txDelay < (0.25 °— msgTxInterval). The default value is 2
seconds.
Table 4.72
Click Apply to make the configurations take effect.
L2 Features > LLDP > LLDP Port Settings
The Basic LLDP Port Settings page displays LLDP port information and contains parameters for configuring
LLDP port settings.
D-Link DMS-1100 Series User Manual
80
Figure 4.100 – L2 Features> LLDP > LLDP Port Settings
The fields that can be configured for the LLDP Port Settings are described below:
Item
Description
From Port/ To Port
Select the range of ports to be configured.
Subtype
Select the subtype of LLDP Type Length Value (TLV). Options to
choose from are MAC Address, and Local.
Admin Status
Select the LLDP transmission mode on the port. The available options
are:
◆ TX: Enables transmitting LLDP packets only.
◆ RX: Enables receiving LLDP packets only.
◆ TX and RX: Enables transmitting and receiving LLDP packets.
This is the default value.
◆ Disabled: Disables LLDP on the port.
IP Subtype
Select the type of the IP address information to be sent. Options to
choose from are All, IPv4 and IPv6.
Action
Select to remove or add the action field.
Address
Enter the IP address to be sent.
Table 4.73
Click Apply to make the configurations take effect.
L2 Features > LLDP > LLDP Management Address List
The LLDP Management Address List page displays the detailed management address information for the
entry.
Figure 4.101 – L2 Features > LLDP >LLDP Management Address List
D-Link DMS-1100 Series User Manual
81
The fields that can be displayed for the LLDP Management Address List are described below:
Item
Description
Management Address
Select IPv4, IPv6 or All address to be displayed.
Subtype
Displays the managed address subtype (e.g. MAC or IPv4)
Address
Displays the IP address.
IF Type
Displays the IF Type.
OID
Displays the SNMP OID.
Advertising Ports
Displays the advertising ports.
Table 4.74
Click Find and the table will update and display the values required.
L2 Features > LLDP > LLDP Basic TLVs Settings
This LLDP Basic TLVs Settings page allows user to configure the LLDP Port settings.
Figure 4.102 – L2 Features > LLDP > LLDP Basic TLVs Settings
The fields that can be configured for the LLDP Basic TLVs Settings are described below:
Item
Description
From Port / To Port
Select the range of ports to be configured.
Port Description
Select to enable or disable the Port Description option.
System Name
Select the system name to be enabled or disabled in the LLDP port. If
enabled is selected, users can specify the content of the system Name.
System Description
Select to enable or disable the System Description option.
System Capabilities
Select to enable or disable the System Capabilities option.
Advertising Ports
Displays the advertising ports.
Table 4.75
Click Apply to make the configurations take effect.
D-Link DMS-1100 Series User Manual
82
L2 Features > LLDP > LLDP Dot1 TLVs Settings
This LLDP Dot1 TLVs Settings page allows user to configure an individual port or group of ports to exclude
one or more of the IEEE 802.1 organizational port VLAN ID TLV data types from outbound LLDP
advertisements.
Figure 4.103 – L2 Features > LLDP > LLDP Dot1 TLVs Settings
The fields that can be configured for the LLDP Dot1 TLVs Settings are described below:
Item
Description
From Port / To Port
Select the range of ports to be configured.
Port VLAN
Select to enable or disable the port VLAN ID TLV to send. The Port
VLAN ID TLV is an optional fixed length TLV that allows a VLAN bridge
port to advertise the port’s VLAN identifier (PVID) that will be
associated with untagged or priority tagged frames.
Protocol VLAN
Select to enable or disable Port and Protocol VLAN ID (PPVID) TLV to
send, and enter the VLAN ID in PPVID TLV.
VLAN Name
Select to enable or disable the VLAN name TLV to send, and enter the
ID of the VLAN in the VLAN name TLV.
Protocol Identity
Select to enable or disable the Protocol Identity TLV to send, and the
protocol name. Options for protocol name to choose from are None,
EAPOL, LACP, GVRP, STP, and All.
Table 4.76
Click Apply to make the configurations take effect.
L2 Features > LLDP > LLDP Dot3 TLVs Settings
The LLDP Dot3 TLVs Settings page allows user to configure an individual port or group of ports to exclude
one or more IEEE 802.3 organizational specific TLV data type from outbound LLDP advertisements.
D-Link DMS-1100 Series User Manual
83
Figure 4.104 – L2 Features > LLDP > LLDP Dot3 TLVs Settings
The fields that can be configured for the LLDP Dot3 TLVs Settings are described below:
Item
Description
From Port / To Port
A consecutive group of ports may be configured starting with the
selected port.
MAC/PHY
Configuration/Status
Select whether the MAC/PHY Configuration Status is enabled on the
port. The possible field values are:
◆ Enabled: Enables the MAC/PHY Configuration Status on the
port.
◆ Disabled: Disables the MAC/PHY Configuration Status on the
port.
Link Aggregation
Specifies whether the link aggregation is enabled on the port. The
possible field values are:
◆ Enabled: Enables the link aggregation configured on the port.
◆ Disabled: Disables the link aggregation configured on the port.
Maximum Frame Size
Specifies whether the link aggregation is enabled on the port. The
possible field values are:
◆ Enabled: Enables the Maximum Frame Size configured on the
port.
◆ Disabled: Disables the Maximum Frame Size configured on the
port.
Power via MDI
Advertises the Power via MDI implementations supported by the port.
The possible field values are:
◆ Enabled: Enables the Power via MDI configured on the port.
◆ Disabled: Disables the Power via MDI configured on the port.
Table 4.77
Click Apply to make the configurations take effect.
D-Link DMS-1100 Series User Manual
84
L2 Features > LLDP > LLDP-MED Port Settings
The LLDP-MED Port Settings page allows user to enable or disable transmitting LLDP-MED TLVs.
Figure 4.105 – L2 Features > LLDP > LLDP-MED Port Settings
The fields that can be configured for the LLDP-MED Port Settings are described below:
Item
Description
From Port / To Port
Select the range of ports to be configured.
Capabilities
Select to enable or disable transmitting the LLDP-MED capabilities
TLV.
Network Policy
Select to enable or disable transmitting the LLDP-MED network policy
TLV.
Inventory
Select to enable or disable transmitting the LLDP-MED inventory
management TLV.
Table 4.78
Click Apply to make the configurations take effect.
L2 Features > LLDP > LLDP Statistics Information
The LLDP Statistics Information page displays an overview of the LLDP information.
D-Link DMS-1100 Series User Manual
85
Figure 4.106 – L2 Features > LLDP > LLDP Statistics Information
The fields that can be displayed for the LLDP Statistics information are described below:
Item
Description
Last Change Time
Displays the time of the last change. It also displays the amount of time
that has elapsed since the change was detected.
Total Inserts
Displays the number of new entries, since the last switch reboot.
Total Deletes
Displays the number of new entries, since the last switch reboot.
Total Drops
Displays the number of LLDP frames dropped due to the table was full.
Total Ageouts
Displays the number of entries deleted due to the Time-To-Live
expiring.
Table 4.79
Click the Clear Counter button to clear the counter information for the statistics displayed.
The fields that can be displayed for the LLDP port Statistics are described below:
Item
Description
Port
Select the port to be displayed.
Total Transmits
Displays the total number of LLDP frames transmitted on the port.
Total Discards
Displays the total discarded frame number of LLDP frames received on
the port.
Total Errors
Displays the Error frame number of LLDP frames received on the port.
Total Receives
Displays the total number of LLDP frames received on the port.
Total TLV Discards
Each LLDP frame can contain multiple pieces of information, known as
TLVs. If a TLV is malformed, it is counted and discarded.
Total TLV Unknowns
Displays the number of well-formed TLVs, but with a known type value.
D-Link DMS-1100 Series User Manual
86
Total Ageouts
Each LLDP frame contains information about how long time the LLDP
information is valid. If no new LLDP frame is received within the age
out time, the LLDP information is removed, and the Age-Out counter is
incremented.
Table 4.80
Click the Clear Counter button to clear the counter information for the statistics displayed.
Click the Clear All button to clear all the counter information displayed.
L2 Features > LLDP > LLDP Local Port Information
The LLDP Local Port Information page displays LLDP local port information.
Figure 4.107 – L2 Features > LLDP > LLDP Local Port Information
The fields that can be displayed for the LLDP Local Port information are described below:
Item
Description
Port
Displays the port number.
Port ID Subtype
Displays the port ID subtype.
Port ID
Displays the port ID (Unit number/Port number).
Port Description
Displays the port description.
Table 4.81
Click Find to displays more information for the specified port.
After clicking the Show Detail button, the following page will appear.
D-Link DMS-1100 Series User Manual
87
Figure 4.108 – L2 Features > LLDP > LLDP Local Port Information – Show Detail
Click the Back button to return to the previous window.
L2 Features > LLDP > LLDP Neighbor Port Information
This LLDP Neighbor Port Information page allows user to view the information on a per-port basis for
populating outbound LLDP advertisements in the local port brief table shown below.
Figure 4.109 – L2 Features > LLDP > LLDP Neighbors Port Information
Click the Find button to locate a specific entry based on the information entered.
Click the Clear button to remove the specified port of LLDP neighbor port or click Clear All button to remove
all LLDP neighbor ports.
L3 Features > IPv4 Interface
The IPv4 Interface page allows displays the information of IPv4 Interface entries.
Figure 4.110 – L3 Features > IPv4 Interface
Click the Edit button to re-configure the specific entry.
Click the Delete button to remove the specific entry.
Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
After clicking the Edit button, the following window will appear.
D-Link DMS-1100 Series User Manual
88
Figure 4.111 – L3 Features > IPv4 Interface Settings - Edit
The fields that can be configured for IPv4 Interface Settings are described below:
Item
Description
Management VLAN Settings
VID (1-4094)
Enter the VLAN ID on which the associated management VLAN ID.
IP Settings
Get IP From
Select Static or DHCP. When the Static option is selected, users can
enter the IPv4 address of this interface manually. When the DHCP
option is selected, this interface will obtain IPv4 information from a
DHCP server located on the local network.
IP Address
Enter the IPv4 Address for this interface.
Mask
Enter the IPv4 subnet mask for this interface.
Table 4.82
Click the Back button to return to the previous window.
Click Apply to make the configurations take effect.
After clicking the DHCP Client tab, the following page will appear.
Figure 4.112 – L3 Features > IPv4 Interface – DHCP Client
The fields that can be configured for the DHCP Client are described below:
Item
Description
DHCP Client Client-ID (1-4094)
Enter the VLAN interface, whose hexadecimal MAC address will be
used as the client ID to be sent with the discover message.
Class ID String
Enter the vendor class identifier with the maximum of 32 characters.
Tick the Hex check box to have the class identifier in the hexadecimal
form.
D-Link DMS-1100 Series User Manual
89
Host Name
Enter the host name.
Lease
Enter the preferred lease time for the IP address to request from the
DHCP server. Enter the day duration of the lease, or select the hour
and minute duration of the lease.
DHCP Retry Times (5-120)
Enter the DHCP retry times. The value is between 5 and 120 and
default is 7 times.
Table 4.83
Click Apply to make the configurations take effect.
L3 Features > IPv4 Default Gateway
The IPv4 Default Gateway page allows user to view and configure the IPv4 default gateway settings.
Figure 4.113 – L3 Features > IPv4 Default Gateway
The fields that can be configured for the IPv4 Default Gateway are described below:
Item
Description
Gateway
Enter the gateway address for IPv4 route. If this is a default route, then
this is the default gateway.
Table 4.84
Click Apply button to accept the changes made.
Click the Delete button to remove the specific entry.
L3 Features > IPv6 Interface
The IPv6 Interface page is used to view the IPv6 interface’s settings.
Figure 4.114 – L3 Features > IPv6 Interface
Click the Detail button to view and configure more detailed settings for the IPv6 interface entry.
After clicking the Detail button, the following window will be appeared.
D-Link DMS-1100 Series User Manual
90
Figure 4.115 – L3 Features > IPv6 Interface - Detail
The fields that can be configured for IPv6 Interface Settings are described below:
Item
Description
IPv6 Interface Settings
IPv6 State
Select to enable or disable the IPv6 interface’s global state.
Static IPv6 Address Settings
IPv6 Address
Enter the IPv6 address for this IPv6 interface. Select the EUI-64 option
to configure an IPv6 address on the interface using the EUI-64
interface ID. Select the Link Local option to configure a link-local
address for the IPv6 interface.
NS Interval Settings
NS Interval (1-3600)
Specify the NS interval and the values are between 1 and 3600.
Table 4.85
Click Apply to make the configurations take effect.
After clicking the Interface IPv6 Address tab located at the top of the page, the following page will appear:
Figure 4.116 – L3 Features > IPv6 Interface – Interface IPv6 Address
Click the Delete button to remove the specific entry.
L3 Features > IPv6 Default Gateway
The IPv6 Default Gateway is used to configure the IPv6 default gateway.
Figure 4.117 – L3 Features > IPv6 Default Gateway
D-Link DMS-1100 Series User Manual
91
The fields that can be configured for the IPv6 Default Gateway are described below:
Item
Description
Interface VLAN (1-4094)
Enter interface’s VLAN ID that will be associated with this route.
Next Hop IPv6 Address
Enter the router’s next hop IPv6 address.
Table 4.86
Click Apply to make the configurations take effect.
QoS > Port Default CoS
The Port Default CoS page allows user to view and configure the port’s default CoS settings.
Figure 4.118 – QoS > Port Default CoS
The fields that can be configured for the Port Default Cos are described below:
Item
Description
From Port / To Port
Select the range of ports to be configured.
Default CoS
Select the default CoS option for the specified ports. The values are
from 0 to 7. Click the Override check box to apply the port's default
CoS to all packets (tagged or untagged) received by the port. Select
the None option to use the default settings.
Table 4.87
Click Apply to make the configurations take effect.
QoS > Port Scheduler Method
The Port Scheduler Method page allows user to view and configure the port scheduler method settings.
D-Link DMS-1100 Series User Manual
92
Figure 4.119 – QoS > Port Scheduler Method
The fields that can be configured for the Port Scheduler Method are described below:
Item
Description
From Port / To Port
Select the range of ports to be configured.
Scheduler Method
Select the scheduler method for the specified ports. Available options
are Strict Priority (SP), Round-Robin (RR), Weighted Round-Robin
(WRR), and Weighted Deficit Round-Robin (WDRR). By default, the
output queue scheduling algorithm is WRR.
Table 4.88
Click Apply to make the configurations take effect.
QoS > Queue Settings
The Queue Settings page allows user to configure the queue settings.
Figure 4.120 – QoS > Queue Settings
The fields that can be configured for the Queue Settings are described below:
Item
Description
Queue ID
Select the queue ID value. The range is between 0 and 7.
WRR Weight (0-127)
Enter the WRR weight value. The value is between 0 and 127.
Table 4.89
D-Link DMS-1100 Series User Manual
93
Click Apply to make the configurations take effect.
QoS > CoS to Queue Mapping
The CoS to Queue Mapping page allows user to view and configure the CoS-to-Queue mapping settings.
Figure 4.121 – QoS > CoS to Queue Mapping
The fields that can be configured for the Queue Settings are described below:
Item
Description
Queue ID
Select the queue ID that will be mapped to the corresponding CoS
value. The value is from are 0 to 7.
Table 4.90
Click Apply to make the configurations take effect.
QoS > Port Rate Limiting
The Port Rate Limiting page allows user to view and configure the port rate limiting settings.
Figure 4.122 – QoS > Port Rate Limiting
The fields that can be configured for the Port Rate Limiting are described below:
Item
Description
From Port / To Port
Select the range of ports to be configured.
D-Link DMS-1100 Series User Manual
94
Direction
Select the direction. Available options are Input and Output. When
Input is selected, the rate limit for ingress packets is configured. When
Output is selected, the rate limit for egress packets is configured.
Rate Limit
Enter the Rate Limit for the specified port.
When Bandwidth is selected, enter the input/output bandwidth value
used in the space provided. This value must be between 64 and
10000000 kbps. Also, enter the Burst Size value in the space
provided. This value must be between 0 and 128000 kilobytes.
When Percent is selected, enter the input/output bandwidth
percentage value used in the space provided. This value must be
between 1 and 100 percent (%). Also, enter the Burst Size value in the
space provided. This value must be between 0 and 128000 kilobytes.
Select the None option to remove the rate limit on the specified port(s).
The specified limitation cannot exceed the maximum speed of the
specified interface. For the ingress bandwidth limitation, the ingress
can trigger a pause frame or a flow control frame when the received
traffic exceeds the limitation.
Table 4.91
Click Apply to make the configurations take effect.
Security > Safeguard Engine
D-Link’s Safeguard Engine is a robust and innovative technology that automatically throttles the impact of
packet flooding into the switch's CPU. This function helps to protect the Switch from being interrupted by
malicious viruses or worm attacks. This option is enabled by default.
Figure 4.123 – Security > Safeguard Engine
Click Apply to make the configurations take effect.
Security > Trusted Host
The Trusted Host page allows user to view and configure the trusted host settings.
Figure 4.124 Security > Trusted Host
The fields that can be configured for the Trusted Host are described below:
Item
Description
D-Link DMS-1100 Series User Manual
95
IPv4 Host
Specify the IPv4 host address.
Type
Specify the trusted host type. The options are Ping, HTTP and HTTPS.
Table 4.92
Click Apply to make the configurations take effect.
Security > Traffic Segmentation Settings
This feature provides administrators to limit traffic flow from a single port to a group of ports on a single
Switch. This method of segmenting the flow of traffic is similar to using VLANs to limit traffic, but is more
restrictive.
Figure 4.125 – Security > Traffic Segmentation Settings
The fields that can be configured for the Traffic Segmentation Settings are described below:
Item
Description
From Port / To Port
Select the range of ports to be configured.
From Forward Port / To
Forward Port
Select the range of forward ports to be configured.
Table 4.93
Click the Add button to add a new entry.
Click the Delete button to remove an entry based on the information entered.
Security > Storm Control Settings
The Storm Control Settings page allows user to view and configure the storm control settings.
D-Link DMS-1100 Series User Manual
96
Figure 4.126 – Security > Storm Control Settings
The fields that can be configured for Storm Control Settings are described below:
Item
Description
Storm Control Trap Settings
Trap State
Select the storm control trap state. The options are None, Storm
Occur, Storm Clear, and Both. When None is selected, no traps will
be sent. When Storm Occur is selected, a trap notification will be sent
when a storm event is detected. When Storm Clear is selected, a trap
notification will be sent when a storm event is cleared.
Storm Control Trap Polling Settings
Interval (1-300)
Enter the interval value. The range is from 1 to 300.
Retries (0-360)
Enter the retry value. The range is from 0 to 360.
Storm Control Port Settings
From Port / To Port
Select the range of ports to be configured.
Type
Select the type of storm attack. The values are Broadcast, Multicast,
and Unicast.
Action
Select the action for the specified ports. The values are None,
Shutdown and Drop.
PPS Rise (1-2147483647)
Enter the rise packets per second value. The value is from 1 to
2147483647.
PPS Low (1-2147483647)
Enter the low packets per second value. The value is from 1 to
2147483647.
Table 4.94
D-Link DMS-1100 Series User Manual
97
Click Apply to make the configurations take effect.
Security > DoS Attack Prevention Settings
The DoS Attack Prevention Settings page allows user to view and configure the Denial-of-Service (DoS)
attack prevention settings.
Figure 4.127 – Security > DoS Attack Prevention Settings
The fields that can be configured for DoS Attack Prevention Settings are described below:
Item
Description
DoS Attack Prevention Settings
DoS Type Selection
Tick the DoS type to be prevented. The options are Land Attack, TCP
Null, TCP Xmas, TCP SYN-FIN, Ping of Death Attack and All Types.
DoS Settings
State
Select to enable or disable the DoS attack prevention state.
Action
Select the action for the DoS attack.
Table 4.95
Click Apply to make the configurations take effect.
Security > SSL > SSL Global Setting
Secure Sockets Layer (SSL) is a security feature that provides a secure communication path between the
management PC and the Switch Web UI by using authentication, digital signatures and encryption. These
security functions are implemented by Ciphersuite, a security string that determines the cryptographic
parameters, encryption algorithms and key sizes.
This page allows user to configure the SSL global state settings.
Figure 4.128 – Security > SSL > SSL Settings
The fields that can be configured for SSL Settings are described below:
D-Link DMS-1100 Series User Manual
98
Item
Description
SSL Status
Select to enable or disable the SSL feature’s global status.
Service Policy
Enter service policy name.
Table 4.96
Click Apply to make the configurations take effect.
NOTE: When SSL is enabled, it will take longer to
open a web page due to the extra processing
required for encryption. After saving, please wait
about 10 seconds for the system summery page
to load.
Security > SSL > SSL Service Policy
The SSL Service Policy page allows user to view and configure the SSL service policy settings.
Figure 4.129 – Security > SSL > SSL Service Policy
The fields that can be configured for SSL Service Policy are described below:
Item
Description
Policy Name
Enter a policy name for SSL.
Session Cache Timeout (60-
86400)
Enter the session cache timeout value. The value is between 60 and
86400 seconds.
Cipher Suites
Select the cipher suites that will be associated with this profile.
Table 4.97
Click the Add button to save your settings.
Click the Find button to locate a specific entry based on the information entered.
Click Apply to make the configurations take effect.
D-Link DMS-1100 Series User Manual
99
OAM > Cable Diagnostics
The Cable Diagnostics page is designed primarily for administrators and customer service representatives to
examine the copper cable quality. It determines the type of cable errors in the cable. Select the range of
ports and then click the Test button to start the diagnosis.
Figure 4.130 – OAM > Cable Diagnostic
Click the Clear button to clear all the information for the specific port.
Click the Clear All button to clear all the information in this table.
NOTE: Cable length detection is available on
Gigabit ports only.
NOTE: Please be sure that the Power Saving
feature is disabled before enabling the Cable
Diagnostics function.
Monitoring > Statistics > Port
This Port page allows user to display the port traffic statistics.
Figure 4.131 – Monitoring > Statistics > Port
The fields that can be displayed for Port information are described below:
D-Link DMS-1100 Series User Manual
100
Item
Description
From Port / To Port
Select the range of ports to be configured.
Table 4.98
Click the Find button to locate a specific entry based on the information entered.
Click the Refresh button to refresh the display table.
After clicking the Show Detail button, the following page will appear.
Figure 4.132 – Monitoring > Statistics > Port – Show Detail
Click the Back button to return to the previous window.
Click the Refresh button to refresh the display table.
Monitoring > Statistics > Port Counters
The Port Counters page allows user to display port counter statistics.
D-Link DMS-1100 Series User Manual
101
Figure 4.133 – Monitoring > Statistics > Port Counters
The fields that can be displayed for Port Counters are described below:
Item
Description
From Port / To Port
Select the range of ports to be viewed.
Table 4.99
Click the Find button to locate a specific entry based on the information entered.
Click the Refresh button to refresh the display table.
Click the Show Errors button to see all error counters of the specific port.
After clicking the Show Errors button, the following page will appear.
Figure 4.134 – Monitoring > Statistics > Port Counters – Show Errors
Click the Back button to return to the previous window.
Click the Refresh button to refresh the display table.
D-Link DMS-1100 Series User Manual
102
Monitoring > Statistics > Counters
The Counters page allows user to display all port counters, and clear the port counters of the specified or all
ports.
Figure 4.135 – Monitoring > Statistics > Counters
The fields that can be displayed for Counters are described below:
Item
Description
From Port / To Port
Select the range of ports to be viewed.
Table 4.100
Click the Find button to locate a specific entry based on the information entered.
Click the Refresh button to refresh the display table.
Click the Clear button to clear all the information for the specific ports.
Click the Clear All button to clear all the information in this table.
Click the Show Detail button to see the detail information of the specific port.
After clicking the Show Detail button, the following page will appear.
D-Link DMS-1100 Series User Manual
103
Figure 4.136 – Monitoring > Statistics > Counters – Show Detail
Click the Back button to return to the previous window.
Click the Refresh button to refresh the display table.
Monitoring > Mirror Settings
The Mirror Settings page allows user to view and configure the port mirroring feature.
Figure 4.137 – Monitoring > Mirror Settings
The fields that can be configured for Mirror Settings are described below:
Item
Description
Mirror Settings
Session Number
Select the mirror session number for the entry.
D-Link DMS-1100 Series User Manual
104
Destination
Select the destination port for mirror settings.
Source
Select the range of ports to be the source port and Frame Type to be
mirrored.
Mirror Session Table
Mirror Session Table
Select the Mirror Session Type to be displayed.
Table 4.101
Click the Add button to add the newly configured mirror entry based on the information entered.
Click the Delete button to delete an existing mirror entry based on the information entered.
Click the Find button to locate a specific entry based on the information entered.
Green > Power Saving
The Power Saving page allows user to configure the power saving settings of the Switch.
Figure 4.138 – Green > Power Saving
The fields that can be configured for Power Saving are described below:
Item
Description
Administrative Dim-LED
Select to enable or disable the scheduled port shutdown power saving
feature.
Table 4.102
Click Apply to make the configurations take effect for each individual section.
Green > EEE
The Energy Efficient Ethernet (EEE) is defined in IEEE 802.3az. It is designed to reduce the energy
consumption of a link when no packets are being sent.
Figure 4.139 – Green > EEE
The fields that can be configured for EEE are described below:
D-Link DMS-1100 Series User Manual
105
Item
Description
From Port / To Port
Select the range of ports to be configured.
State
Select to enable or disable the EEE feature.
Table 4.103
Click Apply to make the configurations take effect.
Appendix A - Technical Specifications D-Link DMS-1100 Series User Manual
106
Appendix A - Technical Specifications
This appendix contains the device specifications, and contains the topics:
• Hardware Specifications
• Features
Hardware Specifications
Key Components / Performance
Switching Capacity
DMS-1100-10TS: 80Gbps
DMS-1100-10TP: 80Gbps
Max. Forwarding Rate
DMS-1100-10TS: 59.52Mpps
DMS-1100-10TP: 59.52Mpps
Forwarding Mode
Store and Forward
Packet Buffer memory
DMS-1100-10TS: 1.5Mbytes
DMS-1100-10TP: 1.5Mbytes
DDRIII for CPU
256M bytes
Flash Memory
128M Bytes
Priority Queues
8 Priority Queues per port
Port Functions
10/100/1000/2.5GBASE-T
Ethernet Ports
DMS-1100-10TS: 8 x 10/100/1000/2.5GBASE-T ports
DMS-1100-10TP: 8 x 10/100/1000/2.5GBASE-T ports
1000Base-T ports compliant to following standards:
IEEE 802.3 compliance
IEEE 802.3u compliance
IEEE 802.3ab compliance
IEEE 802.3bz compliance
Support Half/Full-Duplex operations
IEEE 802.3x Flow Control support for Full-Duplex mode
Back Pressure for Half-Duplex mode
Head-of-line blocking prevention
Support manual/auto MDI/MDIX configuration
Support Auto-Negotiation for each port
Hardware interrupt signal to CPU when port link down for ERPS
SFP+ Ports
DMS-1100-10TS: 2 x 1000/10G ports (Port 9 and Port 10)
DMS-1100-10TP: 2 x 1000/10G ports (Port 9 and Port 10)
Supported SFP+ Direct Attached Cables:
DEM-CB100S: 10-GbE SFP+ 1m Direct Attach Cable
DEM-CB300S: 10-GbE SFP+ 3m Direct Attach Cable
Appendix A - Technical Specifications D-Link DMS-1100 Series User Manual
1
10
07
7
DEM-CB700S: 10-GbE SFP+ 7m Direct Attach Cable
Physical & Environment
Power Consumption
DMS-1100-10TS:
Maximum power consumption: 33.7 Watts
Standby power consumption: 21.6 Watts
DMS-1100-10TP:
Maximum power consumption: 293.4 Watts (PoE on), 38.1 Watts (PoE Off)
Standby power consumption: 27.3 Watts
Power Supply
AC input, 100~240 VAC, 50/60Hz, internal universal power supply
Fans
DMS-1100-10TS: 1 Smart Fan
DMS-1100-10TP: 3 Smart Fans
Operating Temperature
-5~50°C
Storage Temperature
-40~70°C
Humidity
Storage: 0%~95% non-condensing
Dimensions
DMS-1100-10TS: 440mm x 210mm x 44mm
DMS-1100-10TP: 440mm x 250mm x 44mm
Weight
DMS-1100-10TS: 2.53kg
DMS-1100-10TP: 3.43kg
EMI
CE, FCC/IC, VCCI, BSMI, C-Tick, CCC
Safety
UL, CB, BSMI, CCC
Appendix A - Technical Specifications D-Link DMS-1100 Series User Manual
108
Features
L2 Features
Supports up to 16K MAC address
Jumbo frame: Supports up to 9KB
IGMP snooping: Supports 192 multicast
group (shared with MLD Snooping)
MLD Snooping: Supports 192 multicast
group (shared with IGMP Snooping)
802.1D Spanning Tree
802.1s MSTP
ERPS
Loopback Detection
802.3ad Link Aggregation:
- DMS-1100-10TS: up to 8 groups per
device and 8 ports per group
- DMS-1100-10TP: up to 8 groups per
device and 8 ports per group
Port mirroring
L3 Features
Support 1 IPv4 and 1 IPv6 interfaces
VLAN
802.1Q VLAN standard (VLAN Tagging)
Up to 4094 static VLAN groups
Asymmetric VLAN
Management VLAN
Auto Voice VLAN
QoS (Quality of Service)
Priority queue mapping by :
- 802.1p
- CoS
Up to 8 queues per port
Supports Strict in queue handling
Bandwidth Control
Security
Trusted Host
Traffic Segmentation
D-Link Safeguard Engine
Broadcast Storm Control
SSL: Support v1/v2
OAM
Cable Diagnostics
Reset button (reset to factory default)
Management
Web-based GUI
SNMP support
DHCP client
Trap setting for destination IP, system
events, fiber port events, twisted-pair port
events
Password access control
Web-based configuration backup /
restoration
Web-based firmware backup/restore
Firmware upgrade & Web-based
management
Reset, Reboot
D-Link Green Technology
Power Saving: Enabled by default to save
power:
- By Link Status: Drastically save power
when the switch port link is down. For
example, no PC connection or the
connected PC is powered off.
- By LED Shut-Off: LEDs can be turned
on/off by port or system through schedule.
- By Port Shut-Off: Each port on the system
can be turned on/off by schedule.
- By System Hibernation: System enters
hibernation by schedule. In this mode,
switches save most power since main
chipsets (both MAC and PHY) are disabled
for all ports, and energy required to power
the CPU is minimal.
Appendix B – Rack mount Instructions D-Link DMS-1100 Series User Manual
1
10
09
9
Appendix B – Rack mount Instructions
Safety Instructions - Rack Mount Instructions - The following or similar rack-mount instructions are included
with the installation instructions:
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than room ambient. Therefore, consideration should be
given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma)
specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised.
C) Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is
not achieved due to uneven mechanical loading.
D) Circuit Overloading - Consideration should be given to the connection of the equipment to the supply
circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.
E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular
attention should be given to supply connections other than direct connections to the branch circuit (e.g. use
of power strips).
110