Product Overview
Hardware Overview
- LEDs
- Connections
Basic Installation
- Hardware Setup
Web User Interface
Knowledge Base
- Wireless Basics
- Wireless Installation Considerations
Troubleshooting
- Why can’t I access the web-based configuration utility?
Technical Specifications
Antenna Pattern
Contacting Technical Support
Warranty
Registration

D-Link N300 User Manual

Displayed below is the user manual for N300 by D-Link which is a product in the Wireless Access Points category. This manual has pages.

Related Manuals

Toshiba N300 Manual

Document Created by Nick Schuster

Table of Contents

D-Link DAP-2330 User Manual 2

Table of Contents

Product Overview ...................................................................... 4

Introduction ................................................................................... 4

Features ............................................................................................5

Package Contents .........................................................................6

System Requirements ................................................................. 6

Hardware Overview ..................................................................7

LEDs ...................................................................................................7

Connections ...................................................................................7

Basic Installation ........................................................................8

Hardware Setup ............................................................................8

Method 1 - PoE with PoE Switch .....................................8

Method 2 - PoE without PoE Switch or Router ................9

Method 3 - No PoE..............................................................10

Web User Interface ................................................................. 11

Wireless ..........................................................................................12

Access Point Mode .............................................................12

WDS with AP Mode ............................................................14

WDS Mode ............................................................................16

Wireless Client Mode .........................................................18

Wireless Security .................................................................19

Wired Equivalent Privacy (WEP) ..............................19

Wi-Fi Protected Access (WPA / WPA2)....................20

802.1x Authentication ................................................. 22

LAN ..........................................................................................23

IPv6 ..........................................................................................24

Advanced Settings .....................................................................25

Performance .........................................................................26

Wireless Resource Control .......................................................28

Multi-SSID ..............................................................................30

VLAN ........................................................................................32

VLAN List ..........................................................................32

Port List ............................................................................. 33

Add/Edit VLAN ...............................................................34

PVID Settings ..................................................................35

Intrusion .................................................................................36

Schedule ................................................................................37

Internal RADIUS Server .....................................................38

ARP Spoong Prevention ................................................39

Bandwidth Optimization .................................................40

AP Array ..................................................................................42

AP Array Scan .................................................................42

Conguration Settings ................................................ 43

Auto-RF ............................................................................. 47

Load Balance ..................................................................48

Captive Portal ....................................................................... 49

Authentication Settings - Passcode .......................49

Authentication Settings - User Name/Password 50

Authentication Settings - Remote RADIUS ..........51

Authentication Settings - LDAP ...............................52

Authentication Settings - POP3 ...............................53

Table of Contents

D-Link DAP-2330 User Manual 3

Web Redirection ............................................................ 55

DHCP Server .........................................................................56

Dynamic Pool Settings ................................................ 56

Static Pool Setting ........................................................57

Current IP Mapping List ..............................................58

Filters .......................................................................................59

Wireless MAC ACL .........................................................59

WLAN Partition ..............................................................60

Trac Control...............................................................................61

Uplink/Downlink Setting .................................................61

QoS...........................................................................................62

Trac Manager .................................................................... 63

Status ..............................................................................................64

Device Information ............................................................65

Client Information ..............................................................66

WDS Information Page .....................................................67

Channel Analyze .................................................................68

Stats Page ......................................................................................69

Ethernet Trac Statistics ..................................................69

WLAN Trac Statistics .......................................................70

Log ...................................................................................................71

View Log .................................................................................71

Log Settings ..........................................................................72

Maintenance Section ................................................................73

Administration ............................................................................. 74

Limit Administrator ............................................................74

System Name Settings ......................................................75

Console Settings .................................................................75

SNMP Settings .....................................................................76

Administration ............................................................................. 77

Central WiFiManager Settings ........................................ 77

Firmware and SSL Upload ................................................78

Conguration File Upload ...............................................79

Time and Date Settings ....................................................80

Conguration and System.......................................................81

System Settings ........................................................................... 82

Help .................................................................................................83

Knowledge Base ..................................................................... 84

Wireless Basics .............................................................................84

Wireless Installation Considerations .................................... 85

Troubleshooting ..................................................................... 86

Why can’t I access the web-based conguration

utility? .....................................................................................86

What can I do if I forgot my password? ....................... 86

How to check your IP address? ......................................87

How to statically assign an IP address? .......................88

Technical Specications ........................................................ 89

Antenna Pattern ..................................................................... 90

Contacting Technical Support .............................................. 91

Warranty ................................................................................... 92

Registration ............................................................................. 98

Section 1 - Product Overview

D-Link DAP-2330 User Manual 4

Product Overview

Introduction

D-Link, an industry pioneer in wireless networking, introduces a solution for businesses seeking to deploy next generation 802.11n LANs. D-Link unveils

its new DAP-2330, designed specically for environments with high trac areas such as airports, coee shops, shopping centers, sporting venues, and

school campuses to provide secure and manageable dual band wireless network options for network administrators.

Versatile Access Point

The DAP-2330 Access Point allows network administrators to deploy a highly manageable and extremely robust dual band wireless network. For

advanced installations, this new high-speed Access Point has integrated 802.3af Power over Ethernet (PoE) support, allowing installation of this device in

areas where power outlets are not readily available. In addition to bridging 802.11b/g/n wireless networks, the DAP-2330 can bridge to wired networks

with its integrated Gigabit (10/100/1000Mbps) Ethernet port.

Enhanced Performance

The DAP-2330 delivers reliable wireless performance with maximum wireless signal rates of up to 300Mbps. This, coupled with support for Wi-Fi

Multimedia™ (WMM) Quality of Service features, makes it an ideal access point for audio, video, and voice applications.

Security

To help maintain a secure wireless network, the DAP-2330 provides the latest in wireless security technologies by supporting both Personal and Enterprise

versions of WPA and WPA2 (802.11i) with support for RADIUS server back end. To further protect your wireless network, MAC Address Filtering, Wireless

LAN segmentation, Disable SSID Broadcast, Rogue AP Detection, and Wireless Broadcast Scheduling are also included.

* Maximum wireless signal rate derived from IEEE Standard 802.11g and 802.11n specications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network trac,

building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely aect wireless signal range.

Section 1 - Product Overview

D-Link DAP-2330 User Manual 5

Features

yProvide Ethernet to Wireless LAN bridge fully IEEE 802.3/u compatible on the Ethernet side and fully interoperable with IEEE 802.11b/g/n compliant

equipment

yCompatible with IEEE 802.11b high rate standard to provide wireless 11Mbps data rate*

yCompatible with IEEE 802.11g higher speed standard to provide wireless 54Mbps data rate*

yCompatible with IEEE 802.11n higher speed standard to provide wireless 300Mbps data rate*

yOperation at 2.4~2.5GHz frequency band to meet worldwide regulations

ySupports IEEE 802.11b/g/n wireless data encryption with 64/128-bit WEP for security

ySupports enhanced security – WPA-PSK and WPA2-PSK, RADIUS client, and Cipher negotiation

yAllows auto fallback data rate for reliability, optimized throughput and transmission range

yWeb-based conguration and management

ySupports 802.3af PoE

ySupports 802.3az

ySupports one Gigabit Ethernet port

yAP Mode, WDS Mode, WDS with AP, and Wireless Client Mode

ySupports SNMP v1,v2,v3

ySupport Trap server (SNMP v1, v2c)

ySupport Central WiFiManager

ySupport AP Array and AP Array Setup Tool

* Maximum wireless signal rate derived from IEEE Standard 802.11g, and 802.11n specications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network trac,

building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely aect wireless signal range.

Section 1 - Product Overview

D-Link DAP-2330 User Manual 6

Package Contents

• DAP-2330 Access Point

• Power Adapter

• Mounting Plate and Hardware

• Ethernet Cable

• CD (with software and user manual)

• Quick Installation Guide

Note: Using a power supply with a dierent voltage rating than the one included with the DAP-2330 will cause damage and void the warranty for this product.

System Requirements

yComputers with Windows®, Macintosh®, or Linux-based operating systems with an installed Ethernet Adapter

yInternet Explorer Version 11.0, Chrome 33, Safari 7, or Firefox 28 and above (for web-based conguration)

Section 1 - Product Overview

D-Link DAP-2330 User Manual 7

Hardware Overview

LEDs Connections

2Power Receptor Connect the supplied power adapter.

3LAN (PoE) Port Connect to a Power over Ethernet (PoE) switch or router via

an Ethernet cable.

4Reset Button

Press and hold for ve seconds to reset the access point to

the factory default settings. Press and hold for one second

to reboot the access point.

1Power/Status

Solid Red Indicates the access point has

malfunctioned.

Blinking Red This LED will blink during boot-up.

Solid Green Indicates that the DAP-2330 is working

properly.

Blinking Green This light will blink green during data

transmission.

Section 2 - Installation

D-Link DAP-2330 User Manual 8

Basic Installation

Hardware Setup

To power the access point, you can use one of the following 3 methods:

Method 1 - Use if you have a PoE switch or router.

Method 2 - Use if you do not have a PoE switch or router and do not have a power outlet near the location of the access point.

Method 3 - Use if you do not have a PoE switch or router and have a power outlet near the location of the access point.

DAP-2330

PoE Switch or Router

Method 1 - PoE with PoE Switch

1. Connect one end of your Ethernet cable to the LAN (PoE) port on the access point.

2. Connect the other end into one port on a PoE switch.

Section 2 - Installation

D-Link DAP-2330 User Manual 9

Method 2 - PoE without PoE Switch or Router

1. Connect one end of an Ethernet cable into the Data In port on the PoE base unit and the other end into one port on your switch, router, or computer.

2. Connect one end of an Ethernet cable into the P+Data Out port on the PoE base unit and the other end into the LAN (PoE) port on the Access Point.

3. Use the supplied power adapter. Connect the power adapter to the Power In receptor on the PoE adapter.

4. Connect the power cable to the power adapter and then connect the other end into a power outlet.

DAP-2330

Switch or Router

Power Adapter

PoE Base Unit

Section 2 - Installation

D-Link DAP-2330 User Manual 10

Method 3 - No PoE

1. Connect one end of your Ethernet cable into the LAN (PoE) port and then connect the other end to a switch, router, or computer.

2. Use the supplied power adapter. Connect the power adapter to the Power receptor on the Access Point.

3. Connect the power cable to the power adapter and then connect the other end into a power outlet.

DAP-2330

Switch or Router

Power Adapter

Section 3 - Conguration

D-Link DAP-2330 User Manual 11

Web User Interface

The supports an elaborate web user interface where the user can congure and monitor the device. Most of the congurable settings are located

in the left menu of the web GUI which contains section called Basic Settings, Advanced Settings and Status.

Section 3 - Conguration

D-Link DAP-2330 User Manual 12

Wireless

On the wireless settings page, you can setup the basic wireless conguration for the access point. The user can choose from 4 dierent wireless

modes:

Access Point - Used to create a wireless LAN

WDS with AP - Used to connect multiple wireless networks while still functioning as a wireless access point

WDS - Used to connect multiple wireless networks

Wireless Client - Used when the access point needs to act as a wireless network adapter for an Ethernet enabled device

Wireless Band:

Mode:

Network Name (SSID):

SSID Visibility:

Auto Channel Selection:

Select 2.4GHz in default.

Select Access Point from the drop-down menu.

Service Set Identier (SSID) is the name designated

for a specic wireless local area network (WLAN).

The SSID’s factory default setting is dlink. The SSID

can be easily changed to connect to an existing

wireless network or to establish a new wireless

network. The SSID can be up to 32 characters and

is case-sensitive.

Select Enable to broadcast the SSID across the

network, thus making it visible to all network users.

Select Disable to hide the SSID from the network.

This feature when enabled automatically selects

the channel that provides the best wireless

performance. The channel selection process only

occurs when the AP is booting up. To manually

select a channel, set this option to Disable and

select a channel from the drop-down menu.

Access Point Mode

Section 3 - Conguration

D-Link DAP-2330 User Manual 13

Channel:

Channel Width:

Captive Prole:

Authentication:

To change the channel, rst toggle the Auto Channel Selection setting to Disable, and then use the drop-down menu to make

the desired selection.

Note: The wireless adapters will automatically scan and match the wireless settings.

Allows you to select the channel width you would like to operate in. Select 20 MHz if you are not using any 802.11n wireless

clients. Auto 20/40 MHz allows you to connect to both 802.11n and 802.11b/g wireless devices on your network.

Disable or select a Captive Portal prole for Primary SSID.

Use the drop-down menu to choose Open System, Shared Key, WPA-Personal, WPA-Enterprise, or 802.1x.

• Select Open System to communicate the key across the network (WEP).

• Select Shared Key to limit communication to only those devices that share the same WEP settings. If multi-SSID is

enabled, this option is not available.

• Select WPA-Personal to secure your network using a password and dynamic key changes. No RADIUS server is required.

• Select WPA-Enterprise to secure your network with the inclusion of a RADIUS server.

• Select 802.1X if your network is using port-based Network Access Control.

Section 3 - Conguration

D-Link DAP-2330 User Manual 14

Wireless Band:

Mode:

Network Name (SSID):

SSID Visibility:

Auto Channel Selection:

Channel:

Channel Width:

Select 2.4GHz in default.

WDS with AP mode is selected from the drop-down

menu.

Service Set Identier (SSID) is the name designated

for a specic wireless local area network (WLAN).

The SSID’s factory default setting is dlink. The SSID

can be easily changed to connect to an existing

wireless network or to establish a new wireless

network.

Enable or Disable SSID visibility. Enabling this

feature broadcasts the SSID across the network,

thus making it visible to all network users.

Enabling this feature automatically selects

the channel that will provide the best wireless

performance. This feature is not supported in WDS

with AP mode. The channel selection process only

occurs when the AP is booting up.

All devices on the network must share the same

channel. To change the channel, use the drop-down

menu to make the desired selection. (Note: The

wireless adapters will automatically scan and match

the wireless settings.)

Allows you to select the channel width you would

like to operate in. Select 20 MHz if you are not using

any 802.11n wireless clients. Auto 20/40 MHz allows

you to connect to both 802.11n and 802.11b/g

wireless devices on your network.

WDS with AP Mode

Section 3 - Conguration

D-Link DAP-2330 User Manual 15

Captive Prole:

Remote AP MAC Address:

Site Survey:

Authentication:

Disable or select a Captive Portal prole.

Enter the MAC addresses of the APs on your network that will serve as bridges to wirelessly connect multiple networks.

Click on the Scan button to search for available wireless networks, then click on the available network that you want to

connect with.

Use the drop-down menu to choose Open System, Shared Key, or WPA-Personal.

• Select Open System to communicate the key across the network.

• Select Shared Key to limit communication to only those devices that share the same WEP settings. If multi-SSID is enabled,

this option is not available.

• Select WPA-Personal to secure your network using a password and dynamic key changes. No RADIUS server is required.

Section 3 - Conguration

D-Link DAP-2330 User Manual 16

Wireless Band:

Mode:

Network Name (SSID):

SSID Visibility:

Auto Channel Selection:

Channel:

Channel Width:

Captive Prole:

Remote AP MAC Address:

Select 2.4GHz in default.

WDS is selected from the drop-down menu.

Service Set Identier (SSID) is the name designated

for a specic wireless local area network (WLAN). The

SSID’s factory default setting is dlink. The SSID can

be easily changed to connect to an existing wireless

network or to establish a new wireless network.

Enable or Disable SSID visibility. Enabling this

feature broadcasts the SSID across the network, thus

making it visible to all network users.

Enabling this feature automatically selects

the channel that will provide the best wireless

performance. This feature is not supported in WDS

mode.

All devices on the network must share the same

channel. To change the channel, use the drop-down

menu to make the desired selection.

Use the drop-down menu to choose 20 MHz or

Auto 20/40 MHz.

Disable in default.

Enter the MAC addresses of the APs on your network

that will serve as bridges to wirelessly connect

multiple networks.

WDS Mode

Section 3 - Conguration

D-Link DAP-2330 User Manual 17

Site Survey:

Authentication:

Click on the Scan button to search for available wireless networks, then click on the available network that you

want to connect with.

Use the drop-down menu to choose Open System, Shared Key, or WPA-Personal.

• Select Open System to communicate the key across the network.

• Select Shared Key to limit communication to only those devices that share the same WEP settings.

• Select WPA-Personal to secure your network using a password and dynamic key changes. No RADIUS server is

required.

Section 3 - Conguration

D-Link DAP-2330 User Manual 18

Wireless Band:

Mode:

Network Name (SSID):

SSID Visibility:

Auto Channel Selection:

Channel:

Channel Width:

Site Survey:

Captive Prole:

Authentication:

Select 2.4GHz in default.

Wireless Client is selected from the drop-down menu.

Service Set Identier (SSID) is the name designated

for a specic wireless local area network (WLAN). The

SSID’s factory default setting is dlink. The SSID can

be easily changed to connect to an existing wireless

network.

This option is unavailable in Wireless Client mode.

Enabling this feature automatically selects the channel

that will provide the best wireless performance. This

feature is not supported in Wireless Client mode.

The channel used will be displayed, and matches the

AP that the DAP-2330 is connected to when set to

Wireless Client mode.

Use the drop-down menu to choose 20 MHz or Auto

20/40 MHz.

Click on the Scan button to search for available

wireless networks, then click on the available network

that you want to connect with.

Disable in default.

Will be explained in the next topic.

Wireless Client Mode

Section 3 - Conguration

D-Link DAP-2330 User Manual 19

Wireless security is a key concern for any wireless network installed. Unlike any other networking method wireless networks will broadcast it’s presence for

anyone to connect to it. Today, wireless security has advanced to a level where it is virtually impenetrable.

There are mainly two forms of wireless encryption and they are called Wired Equivalent Privacy (WEP) and Wi-Fi Protected Access (WPA). WEP was the rst

security method developed. It is a low level encryption but better than now encryption. WPA is the newest encryption standard and with the advanced WPA2

standard wireless networks have nally reach a point where the security is strong enough to give users the peace of mind when installing wireless networks.

Wireless Security

Wired Equivalent Privacy (WEP)

WEP provides two variations called Open System and Shared Key.

Open System will send a request to the access point and if the key used matches the one congured on the access point, the access point will return a success

message back to the wireless client. If the key does not match the one congured on the access point, the access point will deny the connection request from

the wireless client.

Shared Key will send a request to the access point and if the key used matches the one congured on the access point, the access point will send a challenge

to the client. The client will then again send a conrmation of the same key back to the access point where the access point will either return a successful or a

denial packet back to the wireless client.

Encryption:

Key Type*:

Key Size:

Key Index (1-4):

Key:

Use the radio button to disable or enable

encryption.

Select HEX or ASCII.

Select 64 Bits or 128 Bits.

Select the 1st through the 4th key to be the active

key.

Input up to four keys for encryption. You will select

one of these keys in the Key Index drop-down

menu.

**Hexadecimal (HEX) digits consist of the numbers 0-9 and the letters A-F.

*ASCII (American Standard Code for Information Interchange) is a code that represents English letters using

numbers ranging from 0-127.

Section 3 - Conguration

D-Link DAP-2330 User Manual 20

Wi-Fi Protected Access (WPA / WPA2)

WPA was created by the Wi-Fi Alliance to address the limitations and weaknesses found in WEP. This protocol is mainly based on the 802.11i

standard. There are also two variations found in WPA called WPA-Personal (PSK) and WPA-Enterprise (EAP).

WPA-EAP requires the user to install a Radius Server on the network for authentication.

WPA-Personal does not require the user to install a Radius Server on the network.

Comparing WPA-PSK with WPA-EAP, WPA-PSK is seen as a weaker authentication but comparing WPA-PSK to WEP, WPA-PSK is far more secure

than WEP. WPA-EAP is the highest level of wireless security a user can use for wireless today.

WPA2 is an upgrade of WPA. WPA2 yet again solves some possible security issues found in WPA. WPA2 has two variations called WPA2-Personal

(PSK) and WPA2-Enterprise (EAP) which is the same as found with WPA.

WPA Mode:

Cipher Type:

Group Key Update:

Pass Phrase:

When WPA-Personal is selected for Authentication type,

you must also select a WPA mode from the drop-down

menu: AUTO (WPA or WPA2), WPA2 Only, or WPA Only.

WPA and WPA2 use dierent algorithms. AUTO (WPA or

WPA2) allows you to use both WPA and WPA2.

When you select WPA-Personal, you must also select AUTO,

AES, or TKIP from the pull down menu.

Select the interval during which the group key will be valid.

The default value of 1800 is recommended.

When you select WPA-Personal, please enter a Pass Phrase

in the corresponding eld.

Section 3 - Conguration

D-Link DAP-2330 User Manual 21

WPA Mode:

Cipher Type:

Group Key Update Interval:

Network Access Protection:

RADIUS Server:

RADIUS Port:

RADIUS Secret:

Account Server:

Account Port:

Account Secret:

When WPA-Enterprise is selected, you must also

select a WPA mode from the drop-down menu:

AUTO (WPA or WPA2), WPA2 Only, or WPA Only.

WPA and WPA2 use dierent algorithms. AUTO

(WPA or WPA2) allows you to use both WPA and

WPA2.

When WPA-Enterprise is selected, you must also

select a cipher type from the drop-down menu:

Auto, AES, or TKIP.

Select the interval during which the group key

will be valid. 1800 is the recommended value as

a lower interval may reduce data transfer rates.

Enable or disable Microsoft Network Access

Protection.

Enter the IP address of the RADIUS server.

Enter the RADIUS port.

Enter the RADIUS secret.

Enter the IP address of the Account Server

Enter the Account port

Enter the Account secret

Section 3 - Conguration

D-Link DAP-2330 User Manual 22

802.1x Authentication

Key Update Interval :

RADIUS Server Mode :

RADIUS Server:

RADIUS Port :

RADIUS Secret:

Account Server:

Account Port:

Account Secret:

Select the interval during which the group key will be valid

(300 is the recommended value). A lower interval may

reduce data transfer rates.

Select External or Internal RADIUS server

Enter the IP address of the RADIUS server.

Enter the RADIUS port.

Enter the RADIUS secret.

Enter the IP address of the Account Server

Enter the Account port

Enter the Account secret

Section 3 - Conguration

D-Link DAP-2330 User Manual 23

LAN

LAN is short for Local Area Network. This is considered your internal network. These are the IP settings of the LAN interface for the DAP-2330.

These settings may be referred to as private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal

network and cannot be seen on the Internet.

Get IP From:

IP Address:

Subnet Mask:

Default Gateway:

DNS:

Static IP (Manual) is chosen here. Choose this option if

you do not have a DHCP server in your network, or if you

wish to assign a static IP address to the DAP-2330. When

Dynamic IP (DHCP) is selected, the other elds here will

be grayed out. Please allow about 2 minutes for the DHCP

client to be functional once this selection is made.

The default IP address is 192.168.0.50. Assign a static

IP address that is within the IP address range of your

network.

Enter the subnet mask. All devices in the network must

share the same subnet mask.

Enter the IP address of the gateway/router in your

network.

Enter a DNS server IP address. This is usually the local IP

address of your gateway/router.

Section 3 - Conguration

D-Link DAP-2330 User Manual 24

IPv6

Enable IPv6:

Get IP From:

IP Address:

Prex:

Default Gateway:

Check to enable the IPv6

Auto is chosen here. Choose this option the

DAP-2330 can get IPv6 address automatically

or use Static to set IPv6 address manually.

When Auto is selected, the other elds here will be grayed

out.

Enter the LAN IPv6 address used here.

Enter the LAN subnet prex length value used here.

Enter the LAN default gateway IPv6 address used here.

Section 3 - Conguration

D-Link DAP-2330 User Manual 25

Advanced Settings

In the Advanced Settings Section the user can congure advanced settings concerning Performance, Multiple SSID, VLAN, Security, Quality of Service, AP

Array, Web Redirection, DHCP Server, Filters and Scheduling. The following pages will explain settings found in the Advanced Settings section in more detail.

Section 3 - Conguration

D-Link DAP-2330 User Manual 26

Performance

On the Performance Settings page the users can congure more advanced settings concerning the wireless signal and hosting.

Wireless Band:

Wireless:

Wireless Mode:

Data Rate*:

Beacon Interval (25-500):

DTM Interval (1-15):

Select 2.4Ghz in default.

Use the drop-down menu to turn the wireless function On or O.

The dierent combination of clients that can be supported include

Mixed 802.11n, 802.11g and 802.11b, Mixed 802.11g and 802.11b and

802.11n Only in the 2.4 GHz band Please note that when backwards

compatibility is enabled for legacy (802.11g/b) clients, degradation

of 802.11n wireless performance is expected.

Indicate the base transfer rate of wireless adapters on the wireless

LAN. The AP will adjust the base transfer rate depending on the base

rate of the connected device. If there are obstacles or interference, the

AP will step down the rate. This option is enabled in Mixed 802.11g

and 802.11b mode (for 2.4 GHz). The choices available are Best (Up

to 54), 54, 48, 36, 24, 18, 12, 9, 6, 11, 5.5, 2 or 1 for 2.4 GHz.

Beacons are packets sent by an access point to synchronize a

wireless network. Specify a value in milliseconds. The default (100)

is recommended. Setting a higher beacon interval can help to save

the power of wireless clients, while setting a lower one can help a

wireless client connect to an access point faster.

Select a Delivery Trac Indication Message setting between 1 and 15. 1 is the default setting. DTIM is a countdown informing

clients of the next window for listening to broadcast and multicast messages.

Section 3 - Conguration

D-Link DAP-2330 User Manual 27

Transmit Power:

WMM (Wi-Fi Multimedia):

Ack Time Out

(2.4 GHZ, 64~200):

Short GI:

IGMP Snooping:

Multicast Rate :

Multicast Bandwidth

Control :

Maximum Multicast

Bandwidth :

HT20/40 Coexistence :

Transfer DHCP Oer to

Unicast :

This setting determines the power level of the wireless transmission. Transmitting power can be adjusted to eliminate overlapping

of wireless area coverage between two access points where interference is a major concern. For example, if wireless coverage is

intended for half of the area, then select 50% as the option. Use the drop-down menu to select 100%, 50%, 25%, or 12.5%.

WMM stands for Wi-Fi Multimedia. Enabling this feature will improve the user experience for audio and video applications over

a Wi-Fi network.

To eectively optimize throughput over long distance links enter a value for Acknowledgement Time Out between 64 to 200

microseconds in the 2.4 GHz in the eld provided.

Select Enable or Disable. Enabling a short guard interval can increase throughput. However, be aware that it can also increase

the error rate in some installations due to increased sensitivity to radio-frequency installations.

Select Enable or Disable. Internet Group Management Protocol allows the AP to recognize IGMP queries and reports sent between

routers and an IGMP host (wireless STA). When IGMP snooping is enabled, the AP will forward multicast packets to an IGMP host

based on IGMP messages passing through the AP.

Select the multicast rate for 2.4G band.

Adjust the multicast packet data rate here. The multicast rate is supported in AP mode, and WDS

with AP mode, including Multi-SSIDs.

Set the multicast packets maximum bandwidth pass through rate from the Ethernet interface to the Access Point.

Enable this option to reduce interference from other wireless networks in your area. If the channel width is operating at 40MHz

and there is another wireless network’s channel over-lapping and causing interference, the Access Point will automatically change

to 20MHz.

Enable to transfer the DHCP Oer to Unicast from LAN to WLAN, suggest to enable this function if stations number is larger than 30.

Section 3 - Conguration

D-Link DAP-2330 User Manual 28

Wireless Resource Control

The Wireless Resource Control window is used to congure the wireless connection settings so that the device can detect the better wireless

connection in your environment.

Wireless band:

Connection Limit:

User Limit:

11n Preferred:

Network Utilization:

Aging out:

Select 2.4GHz in default.

Select Enable or Disable. This is an option for load

balancing. This determines whether to limit the num-

ber of users accessing this device. The exact number

is entered in the User Limit eld below. This feature

allows the user to share the wireless network trac

and the client using multiple APs. If this function is

enabled and when the number of users exceeds this

value, or the network utilization of this AP exceeds

the percentage that has been specied, the DAP-

2330 will not allow clients to associate with the AP.

Set the maximum amount of users that are allowed

access (zero to 64 users) to the device using the

specied wireless band. The default setting is 20.

Use the drop-down menu to Enable the 11n Pre-

ferred function. The wireless clients with 802.11n

protocol will have higher priority to connect to the

device.

Set the maximum utilization of this access point for service. The DAP-2330 will not allow any new clients to associate

with the AP if the utilization exceeds the value the user species. Select a utilization percentage between 100%, 80%,

60%, 40%, 20%, or 0%. When this network utilization threshold is reached, the device will pause one minute to allow net-

work congestion to dissipate.

Use the drop-down menu to select the criteria of disconnecting the wireless clients. Available options are RSSI and Data

Rate.

Section 3 - Conguration

D-Link DAP-2330 User Manual 29

RSSI Threshold:

Data Rate Threshold:

ACL RSSI:

ACL RSSI Threshold:

When RSSI is selected in the Aging out drop-down menu, select the percentage of RSSI here. When the RSSI of wireless

clients is lower than the specied percentage, the device disconnects the wireless clients.

When Data Rate is selected in the Aging out drop-down menu, select the threshold of data rate here. When the data

rate of wireless clients is lower than the specied number, the device disconnects the wireless clients.

Use the drop-down menu to Enable the function. When enabled, the device denies the connection request from the

wireless clients with the RSSI lower than the specied threshold below.

Set the ACL RSSI Threshold.

Section 3 - Conguration

D-Link DAP-2330 User Manual 30

Multi-SSID

The device supports up to four multiple Service Set Identiers. You can set the Primary SSID in the Basic > Wireless section. The SSID’s factory

default setting is dlink. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network.

Enable Multi-SSID:

Band:

Index:

SSID:

SSID Visibility:

Security:

Priority:

WMM (Wi-Fi

Multimedia):

Captive Prole:

Check to enable support for multiple SSIDs.

Select 2.4GHz in default.

You can select up to three multi-SSIDs. With the Primary

SSID, you have a total of four multi-SSIDs.

Service Set Identier (SSID) is the name designated for a

specic wireless local area network (WLAN). The SSID’s

factory default setting is dlink. The SSID can be easily

changed to connect to an existing wireless network or to

establish a new wireless network.

Enable or Disable SSID visibility. Enabling this feature

broadcasts the SSID across the network, thus making it

visible to all network users.

The Multi-SSID security can be Open System, WPA-

Personal, or WPA-Enterprise. For a detailed description of

the Open System parameters please go to page 23. For

a detailed description of the WPA-Personal parameters

please go to page 24. For a detailed description of the

WPA-Enterprise parameters please go to page 25.

Select the priority level of the SSID selected.

WMM stands for Wi-Fi Multimedia. Enabling this feature

will improve the user experience for audio and video

applications over a Wi-Fi network.

Enable or disable captive port prole for user authentication.

Section 3 - Conguration

D-Link DAP-2330 User Manual 31

Encryption:

Key Type:

Key Size:

Key Index (1-4):

Key:

WPA Mode:

Cipher Type:

Group Key Update Interval:

Pass Phrase:

Conrm Pass Phrase:

RADIUS Server:

RADIUS Port:

RADIUS Secret:

When you select Open System, toggle between Enable and Disable. If Enable is selected, the Key Type, Key Size, Key Index

(1~4), Key, and Conrm Keys must also be congured.

Select HEX or ASCII.

Select 64-bit or 128-bit.

Select from the 1st to 4th key to be set as the active key.

Input up to four keys for encryption. You will select one of these keys in the Key Index drop-down menu.

When you select either WPA-Personal or WPA-Enterprise, you must also choose a WPA mode from the drop-down menu: AUTO

(WPA or WPA2), WPA2 Only, or WPA Only. WPA and WPA2 use dierent algorithms. AUTO (WPA or WPA2) allows you to use both

WPA and WPA2. In addition, you must congure Cipher Type, and Group Key Update Interval.

Select Auto, AES, or TKIP from the drop-down menu.

Select the interval during which the group key will be valid. The default value of 1800 seconds is recommended.

When you select WPA-Personal, please enter a Pass Phrase in the corresponding eld.

When you select WPA-Personal, please re-enter the Pass Phrase entered in the previous item in the corresponding eld.

When you select WPA-Enterprise, enter the IP address of the RADIUS server. In addition, you must congure RADIUS Port and

RADIUS Secret.

Enter the RADIUS port.

Enter the RADIUS secret.

Section 3 - Conguration

D-Link DAP-2330 User Manual 32

VLAN

The DAP-2330 supports VLANs. VLANs can be created with a Name and VID. Mgmt (TCP stack), LAN, Primary/Multiple SSID, and WDS connection

can be assigned to VLANs as they are physical ports. Any packet which enters the DAP-2330 without a VLAN tag will have a VLAN tag inserted

with a PVID. The VLAN List tab displays the current VLANs.

VLAN Status:

VLAN Mode:

Use the radio button to toggle to Enable. Next,

go to the Add/Edit VLAN tab to add or modify

an item on the VLAN List tab.

The current VLAN mode is displayed.

VLAN List

Section 3 - Conguration

D-Link DAP-2330 User Manual 33

The Port List tab displays the current ports. If you want to congure the guest and internal networks on a Virtual LAN (VLAN), the switch and

DHCP server you are using must also support VLANs. As a prerequisite step, congure a port on the switch for handling VLAN tagged packets as

described in the IEEE 802.1Q standard.

VLAN Status:

Port Name:

Tag VID:

Untag VID:

PVID:

Use the radio button to toggle to Enable. Next, go to the Add/Edit

VLAN tab to add or modify an item on the VLAN List tab.

The name of the port is displayed in this column.

The Tagged VID is displayed in this column.

The Untagged VID is displayed in this column.

The Port VLAN Identier is displayed in this column.

Port List

Section 3 - Conguration

D-Link DAP-2330 User Manual 34

The Add/Edit VLAN tab is used to congure VLANs. Once you have made the desired changes, click the Save button to let your changes take

eect.

VLAN Status:

VLAN ID:

VLAN Name:

Use the radio button to toggle to Enable.

Provide a number between 1 and 4094

for the Internal VLAN.

Enter the VLAN to add or modify.

Add/Edit VLAN

Section 3 - Conguration

D-Link DAP-2330 User Manual 35

The PVID Setting tab is used to enable/disable the Port VLAN Identier Auto Assign Status as well as to congure various types of PVID settings.

Click the Save button to let your changes take eect.

VLAN Status:

PVID Auto Assign Status:

Use the radio button to toggle between

Enable and Disable.

Use the radio button to toggle PVID auto

assign status to Enable.

PVID Settings

Section 3 - Conguration

D-Link DAP-2330 User Manual 36

Intrusion

The Wireless Intrusion Protection window is used to set APs as All, Valid, Neighborhood, Rogue, and New. Click the Save button to let your changes

take eect.

Wireless Band:

AP List:

Detect:

Select 2.4GHz in default.

The choices include All, Valid, Neighbor,

Rogue, and New.

Click this button to initiate a scan of the

network.

Section 3 - Conguration

D-Link DAP-2330 User Manual 37

Schedule

The Wireless Schedule Settings window is used to add and modify scheduling rules on the device. Click the Save button to let your changes take

eect.

Wireless Schedule:

Name:

Index:

SSID:

Day(s):

All Day(s):

Start Time:

End Time:

Use the drop-down menu to enable the device’s

scheduling feature.

Enter a name for the new scheduling rule in the eld

provided.

Use the drop-down menu to select the desired SSID.

This read-only eld indicates the current SSID in use. To

create a new SSID, go to the Wireless Settings window

(Basic Settings > Wireless).

Toggle the radio button between All Week and Select

Day(s). If the second option is selected, check the

specic days you want the rule to be eective on.

Check this box to have your settings apply 24 hours

a day.

Enter the beginning hour and minute, using a 24-hour

clock.

Enter the ending hour and minute, using a 24-hour

clock.

Section 3 - Conguration

D-Link DAP-2330 User Manual 38

Internal RADIUS Server

The DAP-2330 features a built-in RADIUS server. Once you have nished adding a RADIUS account, click the Save button to let your changes take

eect. The newly-created account will appear in this RADIUS Account List. The radio buttons allow the user to enable or disable the RADIUS account.

Click the icon in the delete column to remove the RADIUS account. We suggest you limit the number of accounts below 30.

User Name:

Password:

Status:

RADIUS Account List:

Enter a name to authenticate user access to the

internal RADIUS server.

Enter a password to authenticate user access to the

internal RADIUS server. The length of your password

should be 8~64.

Toggle the drop-down menu between Enable and

Disable.

Displays the list of users.

Section 3 - Conguration

D-Link DAP-2330 User Manual 39

ARP Spoong Prevention

The ARP Spoong Prevention feature allows users to add IP/MAC address mapping to prevent arp spoong attack.

ARP Spoong Prevention:

Gateway IP Address:

Gateway MAC Address:

This check box allows you to enable the arp

spoong prevention function.

Enter a gateway IP address.

Enter a gateway MAC address.

Section 3 - Conguration

D-Link DAP-2330 User Manual 40

Bandwidth Optimization

The Bandwidth Optimization window allows the user to manage the bandwidth of the device and arrange the bandwidth for various wireless clients.

When the Bandwidth Optimization ruile is nished, click the Add button. To discard the Add Bandwidth Optimization Rule settings, click the Clear

button. Click the Save button to let your changes take eect.

Enable Bandwidth

Optimization:

Downlink Bandwidth:

Uplink Bandwidth:

Allocate average BW

for each station:

Allocate maximum BW

for each station:

Allocate dierent BW

for b/g/n stations:

Allocate specic BW

for SSID:

Rule Type:

Use the drop-down menu to Enable the Bandwidth

Optimization function.

Enter the downlink bandwidth of the device in

Mbits per second.

Enter the uplink bandwidth of the device in Mbits

per second.

AP will distribute average bandwidth for each

client.

Specify the maximum bandwidth for each

connected client. Reserve certain bandwidth for

future clients.

The weight of 11b/g/n client are 10%/20%/70% ;

20%/80%. AP will distribute dierent bandwidth

for 11b/g/n clients.

All clients share the total bandwidth.

Use the drop-down menu to select the type

that is applied to the rule. Available options are:

Allocate average BW for each station, Allocate

maximum BW for each station, Allocate

dierent BW for 11 b/g/n stations, and Allocte

specic BW for SSID.

Section 3 - Conguration

D-Link DAP-2330 User Manual 41

Band:

SSID Index:

Downlink Speed:

Uplink Speed:

Use the drop-down menu to toggle the wireless band between 2.4GHz.

Use the drop-down menu to select the SSID for the specied wireless band.

Enter the limitation of the downloading speed in either Kbits/sec or Mbits/sec for the rule.

Enter the limitation of the uploading speed in either Kbits/sec or Mbits/sec for the rule.

Section 3 - Conguration

D-Link DAP-2330 User Manual 42

AP Array

The AP Array window is used to create up to 32 APs on a local network to be organized into a single group in order to increase ease of management.

Click the Save button to let your changes take eect. Central WiFiManager and AP Array are mutually exclusive functions.

Enable AP Array:

AP Array Name:

AP Array Password:

Scan AP Array List:

Connection Status:

AP Array List:

Current Members:

Select the check box to enable the AP array

function. The three modes that are available are

Master, Backup Master, and Slave. APs in the

same array will use the same conguration. The

conguration will sync the Master AP to the Slave

AP and the Backup Master AP when a Slave AP and

a Backup Master AP join the AP array.

Enter an AP array name for the group here.

Enter an AP array password for the group here.

This password must be the same on all the APs

in the group.

Click this button to initiate a scan of all the

available APs currently on the network.

Display the AP array connection status.

This table displays the current AP array status for

the following parameters: Array Name, Master

IP, MAC, Master, Backup Master, Slave, and Total.

This table displays all the current array members.

The DAP-2330 AP array feature supports up to

eight AP array members.

AP Array Scan

Section 3 - Conguration

D-Link DAP-2330 User Manual 43

In the AP array conguration settings windows, users can specify which settings all the APs in the group will inherit from the master AP. Make the

required selection in this window and click the Save button to accept the changes made.

Enable AP Array

Conguration:

Wireless Basic

Settings:

Wireless Advanced

Settings:

Multiple SSID & VLAN:

Advanced Functions:

Administration

Settings:

Select to Enable or Disable the AP array congure

feature here.

Select this option to specify the basic wireless

settings that the APs in the group will inherit.

Select this option to specify the advanced wireless

settings that the APs in the group will inherit.

Select this option to specify the multiple SSIDs

and VLAN settings that the APs in the group will

inherit.

Select this option to specify the other advanced

settings that the APs in the group will inherit.

Select this option to specify the administrative

settings that the APs in the group will inherit.

Conguration Settings

Section 3 - Conguration

D-Link DAP-2330 User Manual 44

Network Name (SSID):

SSID Visibility:

Auto Channel Selection:

Channel Width:

Security:

Captive Prole:

Band:

Select this option to use the same SSID.

Select this option to enable SSID visibility.

Select this option to use auto channel selection.

Select this option to use the same channel width.

Wireless Basic Settings

Wireless:

Wireless Mode:

Data Rate:

Beacon Interval:

DTIM Interval:

Transmit Power:

WMM (Wi-Fi

Multimedia):

Ack Time Out:

Wireless ACL:

Select this option to use the same wireless

settings.

Select this option to use the same wireless mode.

Select this option to use the same data rate.

Select this option to use the same beacon interval.

Select this option to use the same DTIM interval.

Wireless Advanced Settings

Select this option to use the same wireless security.

Select this option to use the same captive prole settings.

Select this option to use the same wireless band.

Select this option to use the same transmit power.

Select this option to use the same WMM settings.

Select this option to use the same ACK timeout value.

Select this option to use the same wireless ACL settings.

Section 3 - Conguration

D-Link DAP-2330 User Manual 45

SSID:

SSID Visibility:

Security:

WMM:

Captive Prole:

VLAN:

Select this option to use the same multi-SSIDs.

Select this option to use the same SSID visible.

Select this option to use the same wireless security

settings.

Multiple SSID & VLAN

Short GI:

Link Integrity:

Connection Limit:

IGMP Snooping::

Select this option to use the same short GI settings.

Select this option to use the same link integrity settings.

Select this option to use the same connection limit value.

Select this option to use the same IGMP snooping settings.

Schedule Settings:

QoS Settings:

Log Settings:

Time and Date Settings:

Select this option to use the same schedule

settings.

Select this option to use the same Quality of

Service settings.

Select this option to use the same log settings.

Select this option to use the same time and date

settings.

Advanced Functions

Select this option to use the same WMM settings.

Select this option to use the same captive prole settings.

Select this option to use the same VLAN settings.

Section 3 - Conguration

D-Link DAP-2330 User Manual 46

System Name Settings:

SNMP Settings:

Console Settings:

Limit Administrator:

Ping Control Setting:

Select this option to use the same system name.

Select this option to use the same SNMP settings.

Select this option to use the same login settings.

Administration Settings

ARP Spoong

Prevention:

Bandwidth

Optimization:

Captive Portal:

Auto RF:

Load Balance:

DHCP Server Settings:

Select this option to use the same ARP spoong prevention settings.

Select this option to use the same bandwidth optimization settings.

Select this option to use the same captive portal settings.

Select this option to use the same auto-RF settings.

Select this option to use the same load balancing settings.

Select this option to use the same DHCP server settings.

Select this option to use the same console settings.

Select this option to use the same limit administrator settings.

Select this option to use the same ping control settings.

Section 3 - Conguration

D-Link DAP-2330 User Manual 47

In this windows, users can view and congure the automatic radio frequency settings as well as congure the the auto-initiate period and threshold

values. Click the Save button to accept the changes made.

Enable: Auto-RF:

Initiate Auto-RF:

Auto-Initiate:

Auto-Initiate Period:

RSSI Threshold:

RF Report Frequency:

Select to Enable or Disable the auto-RF feature

here.

Click the Auto-RF Optimize button to initiate the

auto-RF optimization feature.

Select the Enable or Disable the auto-initiate

feature here.

After enabling the auto-initiate option, the auto-

initiate period value can be entered here. This

value must be between 1 and 24 hours.

Select the RSSI threshold value here. This value is

listed in the drop-down menu in increments of

10% from 10% to 100%.

Enter the RF report frequency value here.

Auto-RF

Section 3 - Conguration

D-Link DAP-2330 User Manual 48

In this window, users can view and congure the AP array’s load balancing settings. Click the Save button to accept the changes made.

Enable Load Balance:

Active Threshold:

Select to Enable or Disable the load balance

feature here.

Enter the active threshold value here.

Load Balance

Section 3 - Conguration

D-Link DAP-2330 User Manual 49

Captive Portal

The Captive Portal is a built-in web authentication server. When a station connects to an AP, the web brower will be redirected to a web authentication

page. In this windows, user can view and congure the Captive Portal settings. Click the Add button to add a new entry. Click the Delete or Delete

All button to remove a specic entry or all the entries congured.

Encryption Type:

Passcode Quantity:

Duration:

Last Active Day:

User Limit:

Select the captive portal encryption type here.

Options to choose from are Passcode, User

Name/Password, Remote RADIUS, LDAP and

POP3. In this section we’ll discuss the Passcode

option.

Enter the number of Passcode that will be used

here.

Enter the duration value, in hours, for this

Passcode.

Select the last active date for this Passcode here.

Year, Month and Day selections can be made.

Enter the maximum amount of users that can use

this Passcode at the same time.

Authentication Settings - Passcode

Section 3 - Conguration

D-Link DAP-2330 User Manual 50

Encryption Type:

Restricted Subnets:

Username:

Password:

Group:

Select the captive portal encryption type here.

Options to choose from are Passcode, User

Name/Password, Remote RADIUS, LDAP and

POP3. In this section we’ll discuss the User Name/

Password option.

Enter the restricted subnets here. Access to these

subnets will denied to guest accounts. Up to four

restricted subnet entries can be dened.

Enter the username for the new account here.

Enter the password for the new account here.

Select the group for the new account here.

Options to choose from are Manager and Guest.

Guest accounts will have limited access.

Authentication Settings - User Name/Password

Section 3 - Conguration

D-Link DAP-2330 User Manual 51

Encryption Type:

Remote RADIUS Type:

RADIUS Server:

RADIUS Port:

RADIUS Secret:

Accounting Mode:

Accounting Server:

Accounting Port:

Accounting Secret:

Select the captive portal encryption type here.

Options to choose from are Passcode, User

Name/Password, Remote RADIUS, LDAP and

POP3. In this section we’ll discuss the Remote

RADIUS option.

Select the remote RADIUS server type here.

Currently, only SPAP will be used.

Enter the RADIUS server’s IP address here.

Enter the RADIUS server’s port number here.

Enter the RADIUS server’s shared secret here.

Select to Enable or Disable the accounting mode

here.

Enter the accounting server’s IP address here.

Enter the accounting server’s port number here.

Enter the accounting server’s shared serect here.

Authentication Settings - Remote RADIUS

Section 3 - Conguration

D-Link DAP-2330 User Manual 52

Encryption Type:

Server:

Port:

Authenticate Mode:

Username:

Password:

Base DN:

Account Attribute:

Identity:

Select the captive portal encryption type here.

Options to choose from are Passode, User Name/

Password, Remote RADIUS, LDAP and POP3. In

this section we’ll discuss the LDAP option.

Enter the LDAP server’s IP address or domain

name here.

Enter the LDAP server’s port number here.

Select the authentication mode here. Options to

choose from are Simple and TLS.

Enter the LDAP server account’s username here.

Enter the LDAP server account’s password here.

Enter the administrator’s domain name here.

Enter the LDAP account attribute string here. This

string will be used to search for clients.

Enter the identity’s full path string here.

Alternatively, select the Auto Copy checkbox to

automatically add the generic full path of the web

page in the identity eld.

Authentication Settings - LDAP

Section 3 - Conguration

D-Link DAP-2330 User Manual 53

Encryption Type:

Server:

Port:

Connection Type:

Select the captive portal encryption type here.

Options to choose from are Passode, User Name/

Password, Remote RADIUS, LDAP and POP3.

In this section we’ll discuss the Passcode option.

Enter the POP3 server’s IP address or domain

name here.

Enter the POP server’s port number here.

Select the connection type here. Options to

choose from are None and SSL/TLS.

Authentication Settings - POP3

Section 3 - Conguration

D-Link DAP-2330 User Manual 54

In this window, users can upload a custom login page picture that will be used by the captive portal feature. Click the Browse button to navigate

to the image le, located on the managing computer and then click the Upload button to initiate the upload.

Upload picture from

le:

In this eld the path to the image le, that will be

uploaded, will be displayed. Alternatively, the path

can be manually entered here.

Section 3 - Conguration

D-Link DAP-2330 User Manual 55

Web Redirection

In this windows, users can view and congure the Web redirection settings for the captive portal hosted by this access point. Wireless clients will

be redirected to this web site prior and after authentication. Click the Save button to accept the changes made.

Web Redirection:

Web Site:

Select this checkbox to enable the Web redirection

feature.

Enter the destination web site’s address here.

Section 3 - Conguration

D-Link DAP-2330 User Manual 56

DHCP Server

The DHCP address pool denes the range of the IP address that can be assigned to stations in the network. A Dynamic Pool allows wireless

stations to receive an available IP with lease time control. If needed or required in the network, the DAP-2330 is capable of acting as a DHCP

server.

Function Enable/Disable:

IP Assigned From:

The Range of Pool (1-254):

Subnet Mask:

Gateway:

WINS:

DNS:

Domain Name:

Lease Time:

Dynamic Host Configuration Protocol (DHCP) assigns

dynamic IP addresses to devices on the network. This protocol

simplies network management and allows new wireless

devices to receive IP addresses automatically without the

need to manually assign new IP addresses. Select Enable to

allow the DAP-2330 to function as a DHCP server.

Input the rst IP address available for assignment on your

network.

Enter the number of IP addresses available for assignment.

IP addresses are increments of the IP address specied in the

“IP Assigned From” eld.

Dynamic Pool Settings

All devices in the network must have the same subnet mask to communicate. Enter the subnet mask for the network

here.

Enter the IP address of the gateway on the network.

Specify the Windows Internet Naming Service (WINS) server address for the wireless network. WINS is a system that

determines the IP address of a network computer that has a dynamically assigned IP address.

Enter the IP address of the Domain Name System (DNS) server. The DNS server translates domain names such as

www.dlink.com into IP addresses.

Enter the domain name of the network, if applicable. (An example of a domain name is: www.dlink.com.)

The lease time is the period of time before the DHCP server will assign new IP addresses.

Section 3 - Conguration

D-Link DAP-2330 User Manual 57

Static Pool Setting

The DHCP address pool denes the range of IP addresses that can be assigned to stations on the network. A static pool allows specic wireless

stations to receive a xed IP without time control.

Function Enable/Disable:

Assigned IP:

Assigned MAC Address:

Subnet Mask:

Gateway:

WINS:

DNS:

Domain Name:

Dynamic Host Configuration Protocol (DHCP)

assigns IP addresses to wireless devices on

the network. This protocol simplifies network

management and allows new wireless devices

to receive IP addresses automatically without

the need to manually assign IP addresses. Select

Enable to allow the DAP-2330 to function as a

DHCP server.

Use the Static Pool Settings to assign the same IP

address to a device every time you start up. The

IP addresses assigned in the Static Pool list must

NOT be in the same IP range as the Dynamic

Pool. After you have assigned a static IP address

to a device via its MAC address, click Apply; the

device will appear in the Assigned Static Pool at

the bottom of the screen. You can edit or delete

the device in this list.

Enter the MAC address of the device requesting

association here.

Dene the subnet mask of the IP address specied

in the “IP Assigned From” eld.

Specify the Gateway address for the wireless network.

Specify the Windows Internet Naming Service (WINS) server address for the wireless network. WINS is a system that

determines the IP address of a network computer with a dynamically assigned IP address, if applicable.

Enter the DNS server address for your wireless network.

Specify the domain name for the network.

Section 3 - Conguration

D-Link DAP-2330 User Manual 58

Current IP Mapping List

This window displays information about the current assigned DHCP dynamic and static IP address pools. This information is available when you

enable DHCP server on the AP and assign dynamic and static IP address pools.

Current DHCP Dynamic

Prole:

Binding MAC Address:

Assigned IP Address:

Lease Time:

Current DHCP Static Pools:

Binding MAC Address:

Assigned IP Address:

Binding MAC Address:

Assigned IP Address:

These are IP address pools the DHCP server has

assigned using the dynamic pool setting.

The MAC address of a device on the network

that is assigned an IP address from the DHCP

dynamic pool.

The current corresponding DHCP-assigned IP

address of the device.

The length of time that the dynamic IP address

will be valid.

These are the IP address pools of the DHCP

server assigned through the static pool settings.

The MAC address of a device on the network

that is within the DHCP static IP address pool.

The current corresponding DHCP-assigned

static IP address of the device.

The MAC address of a device on the network

that is assigned an IP address from the DHCP

dynamic pool.

The current corresponding DHCP-assigned

static IP address of the device.

Section 3 - Conguration

D-Link DAP-2330 User Manual 59

Filters

This page allows the user to congure Wireless MAC ACL settings for access control.

Wireless Band:

Access Control List:

MAC Address:

MAC Address List:

Current Client

Information:

Displays the current wireless band rate.

Select Disable to disable the lters function.

Select Accept to accept only those devices with MAC

addresses in the Access Control List. All other devices

not on the list will be rejected.

Select Reject to reject the devices with MAC

addresses on the Access Control List. All other devices

not on the list will be accepted.

Enter each MAC address that you wish to include in

your lter list, and click Apply.

When you enter a MAC address, it appears in this list.

Highlight a MAC address and click Delete to remove

it from this list.

This table displays information about all the current

connected stations.

Wireless MAC ACL

Section 3 - Conguration

D-Link DAP-2330 User Manual 60

This page allows the user to congure a WLAN Partition.

Wireless Band:

Link Integrity:

Ethernet WLAN Access:

Internal Station Connection:

Displays the current wireless band.

Select Enable or Disable. If the Ethernet

connection between the LAN and the AP is

disconnected, enabling this feature will cause

the wireless segment associated with the AP to

be disassociated from the AP.

The default is Enable. When disabled, all data

from the Ethernet to associated wireless devices

will be blocked. Wireless devices can still send

data to the Ethernet.

The default value is Enable, which allows stations

to intercommunicate by connecting to a target

AP. When disabled, wireless stations cannot

exchange data on the same Multi-SSID. In Guest

mode, wireless stations cannot exchange data

with any station on your network.

WLAN Partition

Section 3 - Conguration

D-Link DAP-2330 User Manual 61

Trac Control

The uplink/downlink setting allows users to customize the downlink and uplink interfaces including specifying downlink/uplink bandwidth rates

in Mbits per second. These values are also used in the QoS and Trac Manager windows. Once the desired uplink and downlink settings are

nished, click the Save button to let your changes take eect.

Downlink Bandwidth:

Uplink Bandwidth:

The downlink bandwidth in Mbits per second.

Uplink Bandwidth: The uplink bandwidth in

Mbits per second.

Uplink/Downlink Setting

Section 3 - Conguration

D-Link DAP-2330 User Manual 62

Quality of Service (QoS) enhances the experience of using a network by prioritizing the trac of dierent applications. The DAP-2330 supports

four priority levels. Once the desired QoS settings are nished, click the Save button to let your changes take eect.

Enable QoS:

Downlink Bandwidth:

Uplink Bandwidth:

Check this box to allow QoS to prioritize trac.

Use the drop-down menus to select the four

levels of priority. Click the Save button when

you are nished.

Downlink Bandwidth: The downlink bandwidth

in Mbits per second. This value is entered in the

Uplink/Downlink Setting window.

Uplink Bandwidth: The uplink bandwidth in

Mbits per second. This value is entered in the

Uplink/Downlink Setting window.

QoS

Section 3 - Conguration

D-Link DAP-2330 User Manual 63

The trac manager feature allows users to create trac management rules that specify how to deal with listed client trac and specify

downlink/ uplink speed for new trac manager rules. Click the Save button to let your changes take eect.

Trac Manager:

Unlisted Client Trac:

Downlink Bandwidth:

Uplink Bandwidth:

Use the drop-down menu to Enable the trac

manager feature.

Select Deny or Forward to determine how to

deal with unlisted client trac.

The downlink bandwidth in Mbits per second.

This value is entered in the Uplink/Downlink

Setting window.

Uplink Bandwidth:The uplink bandwidth in

Mbits per second. This value is entered in the

Uplink/Downlink Setting window.

Trac Manager

Section 3 - Conguration

D-Link DAP-2330 User Manual 64

Status

In the Status Section the user can monitor and view conguration settings of the access point. Here the user can also view statistics about client

information, WDS information and more. The following pages will explain settings found in the Status section in more detail.

Section 3 - Conguration

D-Link DAP-2330 User Manual 65

Device Information

This page displays the current information like rmware version, Ethernet and wireless parameters, as well as the information regarding CPU and

memory utilization.

Device Information: This read-only window displays the

configuration settings of the DAP-2330,

including the firmware version and the

device’s MAC address.

Section 3 - Conguration

D-Link DAP-2330 User Manual 66

Client Information

This page displays the associated clients SSID, MAC, band, authentication method, signal strength, and power saving mode for the DAP-2330

network.

Client Information:

SSID:

MAC:

Band:

Authentication:

RSSI:

Power Saving Mode:

This window displays the wireless client

information for clients currently connected

to the DAP-2330.

Displays the SSID of the client.

Displays the MAC address of the client.

Displays the wireless band that the client is

connected to.

Displays the type of authentication being

used.

Displays the client’s signal strength.

Displays the status of the power saving

feature.

Section 3 - Conguration

D-Link DAP-2330 User Manual 67

WDS Information Page

This page displays the access points SSID, MAC, band, authentication method, signal strength, and status for the DAP-2330’s Wireless Distribution

System network.

WDS Information:

Name:

MAC:

Authentication:

Signal:

Status:

This window displays the Wireless Distribution

System information for clients currently

connected to the DAP-2330.

Displays the SSID of the client.

Displays the MAC address of the client.

Displays the type of authentication being

used.

Displays the client’s signal strength.

Displays the status of the power saving

feature.

Section 3 - Conguration

D-Link DAP-2330 User Manual 68

Channel Analyze

Wireless Band:

Detect:

AP List:

Select 2.4GHz in default.

Click the Detect button to scan.

This will list the transmitting channels and

quality.

Section 3 - Conguration

D-Link DAP-2330 User Manual 69

Stats Page

Displays wired interface network trac information.

Ethernet Trac Statistics: This page displays transmitted and received

count statistics for packets and bytes.

Ethernet Trac Statistics

Section 3 - Conguration

D-Link DAP-2330 User Manual 70

WLAN Trac Statistics

Displays throughput, transmitted frame, received frame, and WEP frame error information for the AP network.

WLAN Trac Statistics: This page displays wireless network

statistics for data throughput,

transmitted and received frames, and

frame errors.

Section 3 - Conguration

D-Link DAP-2330 User Manual 71

Log

The AP’s embedded memory holds logs here. The log information includes but is not limited to the following items: cold start AP, upgrading

rmware, client associate and disassociate with AP, and web login. The web page holds up to 500 logs.

View Log: The AP’s embedded memory displays

system and network messages including

a time stamp and message type. The log

information includes but is not limited

to the following items: cold start AP,

upgrading rmware, client associate and

disassociate with AP, and web login. The

web page holds up to 500 logs.

View Log

Section 3 - Conguration

D-Link DAP-2330 User Manual 72

Log Settings

Enter the log server’s IP address to send the log to that server. Check or uncheck System Activity, Wireless Activity, or Notice to specify what kind

of log type you want it to log.

Log Server/IP Address:

Log Type:

E-mail Notication:

E-mail Log Schedule:

Enter the IP address of the server you

would like to send the DAP-2330 log to.

Check the box for the type of activity

you want to log. There are three types:

System Activity, Wireless Activity, and

Notice.

Support Simple Mail Transfer Protocol for

log schedule and periodical change key.

It can not support Gmail SMTP port 465.

Please set to Gmail SMTP port 25 or 587.

Use the drop-down menu to set the

e-mail log schedule.

Section 3 - Conguration

D-Link DAP-2330 User Manual 73

Maintenance Section

In the Status Section the user can monitor and view conguration settings of the access point. Here the user can also view statistics about client

information, WDS information and more. The following pages will explain settings found in the maintenance section in more detail.

Section 3 - Conguration

D-Link DAP-2330 User Manual 74

Administration

Check one or more of the ve main categories to display the various hidden administrator parameters and settings displayed on the next ve

pages. Each of the ve main categories display various hidden administrator parameters and settings.

Limit Administrator VLAN

ID:

Limit Administrator IP:

IP Range:

Check the box provided and the

enter the specic VLAN ID that the

administrator will be allowed to log in

from.

Check to enable the Limit Administrator

IP address.

Enter the IP address range that the

administrator will be allowed to log in

from and then click the Add button.

Limit Administrator

Section 3 - Conguration

D-Link DAP-2330 User Manual 75

System Name Settings

Each of the ve main categories display various hidden administrator parameters and settings.

System Name:

Location:

The name of the device. The default

name is D-Link DAP-2330.

The physical location of the device, e.g.

72nd Floor, D-Link HQ.

Each of the ve main categories display various hidden administrator parameters and settings.

User Name:

Old Password:

New Password:

Conrm Password:

Enter a user name. The default is admin.

When changing your password, enter the

old password here.

When changing your password, enter the new password here. The password is case-sensitive. “A” is a dierent

character than “a.” The length should be between 0 and 12 characters.

Enter the new password a second time for conrmation purposes.

Console Settings

Each of the ve main categories display various hidden administrator parameters and settings.

Status:

Console Protocol:

Time-out:

Status is enabled by default. Uncheck the

box to disable the console.

Select the type of protocol you would

like to use, Telnet or SSH.

Set to 1 Min, 3 Mins, 5 Mins, 10 Mins, 15 Mins or Never.

Section 3 - Conguration

D-Link DAP-2330 User Manual 76

SNMP Settings

Each of the ve main categories display various hidden administrator parameters and settings.

Status:

Public Community String:

Private Community String:

Check the box to enable the SNMP

functions. This is enabled by default.

Enter the public SNMP community string.

Enter the private SNMP community

string.

Section 3 - Conguration

D-Link DAP-2330 User Manual 77

Administration

Enable Central

WiFiManager:

Central WiFiManager Settings

The Central WiFiManager section is used to create a set of APs on the Internet to be organized into a single group in order to increase ease of

management. Central WiFiManager and AP Array are mutually exclusive functions.

Select to enable or disable the Central

WiFiManager.

Section 3 - Conguration

D-Link DAP-2330 User Manual 78

Firmware and SSL Upload

This page allows the user to perform a rmware upgrade. A Firmware upgrade is a function that upgrade the running software used by the

access point. This is a useful feature that prevents future bugs and allows for new features to be added to this product. Please go to your local

D-Link website to see if there is a newer version rmware available.

Firmware and SSL

Certication Upload:

Upload Firmware from

Local Hard Drive:

Upload SSL Certication

from Local Hard Drive:

You can upload les to the access point.

The current rmware version is displayed

above the le location eld. After the

latest rmware is downloaded, click on

the “Choose File” button to locate the

new rmware. Once the le is selected,

click on the “Open” and “Upload” button

to begin updating the rmware. Please

don’t turn the power o while upgrading.

After you have downloaded a SSL

certication to your local drive, click

“Choose File.” Select the certication and

click “Open” and “Upload” to complete

the upgrade.

Section 3 - Conguration

D-Link DAP-2330 User Manual 79

Conguration File Upload

This page allows the user to backup and recover the current conguration of the access point in case of a unit failure.

Conguration File Upload

and Download:

Upload Conguration File:

Download Conguration

File:

You can upload and download

conguration les of the access point.

Browse to the saved conguration

le you have in local drive and click

“Open” and “Upload” to update the

conguration.

Click “Download” to save the current

conguration le to your local disk. Note

that if you save one conguration le

with the administrator’s password now,

after resetting your DAP-2330 and then

updating to this saved conguration le,

the password will be gone.

Section 3 - Conguration

D-Link DAP-2330 User Manual 80

Time and Date Settings

Enter the NTP server IP, choose the time zone, and enable or disable daylight saving time.

Current Time:

Enable NTP Server:

NTP Server:

Time Zone:

Enable Daylight

Saving:

Daylight Saving

Dates:

Set the Date and

Time Manually:

Displays the current time and date settings.

Check to enable the AP to get system time

from an NTP server from the Internet.

Enter the NTP server IP address.

Use the drop-down menu to select your

correct Time Zone.

Check the box to enable Daylight Saving

Time.

Use the drop-down menu to select the

correct Daylight Saving oset.

A user can either manually set the time

for the AP here, or click the Copy Your

Computer’s Time Settings button to copy

the time from the computer in use (Make

sure that the computer’s time is set correctly).

Section 3 - Conguration

D-Link DAP-2330 User Manual 81

Conguration and System

These options are the remaining option to choose from in the top menu. Conguration allows the user to save and activate or discard the

congurations done. System allows the user to restart the unit, perform a factory reset or clear the language pack settings. Logout allows the

user to safely log out from the access point’s web conguration. Help allows the user to read more about the given options to congure without

the need to consult the manual. The following pages will explain settings found in the conguration and system section in more detail.

Section 3 - Conguration

D-Link DAP-2330 User Manual 82

System Settings

On this page the user can restart the unit, perform a factory reset of the access point or clear the added language pack.

Restart the Device:

Restore to Factory Default

Settings:

Clear Language Pack:

Click Restart to restart the DAP-2330.

Click Restore to restore the DAP-2330

back to factory default settings.

Click to clear the current Language pack

running.

Section 3 - Conguration

D-Link DAP-2330 User Manual 83

Help

The help page is useful to view a brief description of a function available on the access point in case the manual is not present.

Help: Scroll down the Help page for topics and

explanations.

Appendix A - Wireless Basics

D-Link DAP-2330 User Manual 84

Knowledge Base

D-Link wireless products are based on industry standards to provide high-speed wireless connectivity that is easy to use within your home,

business or public access wireless networks. D-Link wireless products provides you with access to the data you want, whenever and wherever

you want it. Enjoy the freedom that wireless networking can bring to you.

WLAN use is not only increasing in both home and oce environments, but in public areas as well, such as airports, coee shops and universities.

Innovative ways to utilize WLAN technology are allowing people to work and communicate more eciently. Increased mobility and the absence

of cabling and other types of xed infrastructure have proven to be benecial to many users.

Wireless adapter cards used on laptop and desktop systems support the same protocols as Ethernet adapter cards, allowing wireless users to use

the same applications as those used on a wired network.

People use WLAN technology for many dierent purposes:

• Mobility - productivity increases when people can have access to data in any location within the operating range of their WLAN.

Management decisions based on real-time information can signicantly improve the eciency of a worker.

• Low implementation costs - WLANs are easy to set up, manage, change and relocate. Networks that frequently change can benet from

WLAN’s ease of implementation. WLANs can operate in locations where installation of wiring may be impractical.

• Installation and network expansion - by avoiding the complications of troublesome cables, a WLAN system can be fast and easy during

installation, especially since it can eliminate the need to pull cable through walls and ceilings. Wireless technology provides more versatility

by extending the network beyond the home or oce.

• Inexpensive solution - wireless network devices are as competitively priced as conventional Ethernet network devices. The DAP-2330 saves

money by providing users with multi-functionality congurable in four dierent modes.

• Scalability - Congurations can be easily changed and range from Peer-to-Peer networks, suitable for a small number of users to larger

Infrastructure networks to accommodate hundreds or thousands of users, depending on the number of wireless devices deployed.

Wireless Basics

Appendix A - Wireless Basics

D-Link DAP-2330 User Manual 85

The D-Link Access Point lets you access your network using a wireless connection from virtually anywhere within the operating range of your

wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must

pass through, may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your

home or business. The key to maximizing wireless range is to follow these basic guidelines:

1. Keep the number of walls and ceilings between the access point and other network devices to a minimum. Each wall or ceiling can reduce

your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is minimized.

2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a

3. 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick! Position devices so

that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception.

4. Building Materials make a dierence. A solid metal door or aluminum studs may have a negative eect on the range. Try to position access

points, wireless routers, and computers so that the signal passes through drywall or open doorways. Materials and objects such as glass,

steel, metal, walls with insulation, water (sh tanks), mirrors, le cabinets, brick, and concrete will degrade your wireless signal.

5. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF noise.

6. If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security systems), your wireless

connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone base is as far away from your wireless devices as

possible. The base transmits a signal even if the phone in not in use.

Wireless Installation Considerations

Section 6 - Troubleshooting

D-Link DAP-2330 User Manual 86

Troubleshooting

When entering the IP address of the D-Link access point (192.168.0.50 for example), you are not connecting to a website on the Internet or have to

be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must be on the same IP subnet to

connect to the web-based utility.

• Make sure you have an updated Java-enabled web browser. We recommend the following:

• Internet Explorer 7.0 or higher, Chrome, Firefox, or Safari 4 or higher

• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a dierent cable or connect to a

dierent port on the device if possible. If the computer is turned o, the link light may not be on.

• Disable any internet security software running on the computer. Software rewalls such as Zone Alarm, Black Ice, Sygate, Norton Personal Firewall, and

Windows® rewall may block access to the conguration pages. Check the help les included with your rewall software for more information on disabling

or conguring it.

• Congure your Internet settings:

Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click the button to restore the settings to their

defaults.

Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button. Make sure nothing is checked. Click OK.

Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.

Close your web browser (if open) and open it.

• Access the web management. Open your web browser and enter the IP address of your D-Link access point in the address bar. This should open the login

page for your the web management.

• If you still cannot access the conguration, unplug the power to the access point for 10 seconds and plug back in. Wait about 30 seconds and try accessing

the conguration. If you have multiple computers, try connecting using a dierent computer.

Why can’t I access the web-based conguration utility?

This chapter provides solutions to problems that can occur during the installation and operation of the DAP-2330. Read the following

descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a dierent operating system, the

screenshots on your computer will look similar to the following examples.)

If you forgot your password, you must reset your access point. Unfortunately, this process will change all your settings back to the factory defaults.

To reset the access point, locate the reset button (hole) on the rear panel of the unit. With the access point powered on, use a paperclip to hold the

button down for 10 seconds. Release the button and the access point will go through its reboot process. Wait about 30 seconds to access the access

point. The default IP address is 192.168.0.50. When logging in, the username is admin and leave the password box empty.

What can I do if I forgot my password?

Section 6 - Troubleshooting

D-Link DAP-2330 User Manual 87

After you install your network adapter, by default, the TCP/IP settings

should be set to obtain an IP address from a DHCP server (i.e. wireless

router) automatically. To verify your IP address, please follow the steps

below.

Click on Start > Run. In the run box type cmd and click OK.

At the prompt, type ipcong and press Enter.

This will display the IP address, subnet mask, and the default gateway of

your adapter.

If the address is 0.0.0.0, check your adapter installation, security settings,

and the settings on your router. Some rewall software programs may

block a DHCP request on newly installed adapters.

How to check your IP address?

If you are connecting to a wireless network at a hotspot (e.g. hotel, coee shop, airport), please contact an employee or administrator to verify

their wireless network settings.

Section 6 - Troubleshooting

D-Link DAP-2330 User Manual 88

If you are not using a DHCP capable gateway/router, or you need to

assign a static IP address, please follow the steps below:

Step 1:

Windows® 2000: Click on Start > Settings > Control Panel > Network

Connections

Windows XP: Click on Start > Control Panel > Network Connections

Windows Vista®: Click on Start > Control Panel > Network and Internet >

Network and Sharing Center > Manage network connections

Step 2:

Right-click on the Local Area Connection which represents your network

adapter and select Properties.

Step 3:

Highlight Internet Protocol (TCP/IP) and click Properties.

Step 4:

Click Use the following IP address and enter an IP address that is on the

same subnet as your network or the LAN IP address on your router.

Example: If the router’s LAN IP address is 192.168.0.1, make your IP

address 192.168.0.X where X is a number between 2 and 99. Make sure

that the number you choose is not in use on the network. Set Default

Gateway the same as the LAN IP address of your router (192.168.0.1).

Set Primary DNS the same as the LAN IP address of your router

(192.168.0.1). The Secondary DNS is not needed or you may enter a DNS

server from your ISP.

Step 5:

Click OK twice to save your settings.

How to statically assign an IP address?

Appendix C - Technical Specications

D-Link DAP-2330 User Manual 89

Technical Specications

Standards

• IEEE 802.11n

• IEEE 802.11g

• IEEE 802.3

• IEEE 802.3u

• IEEE 802.3b

• IEEE 802.3af

• IEEE 802.3x

Network Management

• Web Browser interface (HTTP, Secure HTTP (HTTPS))

• Central WiFiManager

• SNMP Support (Private MIB)

• Command Line Interface (Telnet, Secure SSH Telnet)

Security

• WPA™ Personal/Enterprise

• WPA2™ Personal/Enterprise

• WEP™ 64-/128-bit

Wireless Frequency Range

• 2.4 to 2.4835 GHz

Operating Voltage

• 802.3af PoE or 12V/1A

Antenna Type

• 2x Internal 3 dBi antennas @2.4GHz

LEDs

• Power/Status

Temperature

• Operating: 0˚C to 40˚C

• Storing: -20˚C to 65˚C

Humidity

• Operating: 10%~90% (non-condensing)

• Storing: 5%~95% (non-condensing)

Certications

• FCC Class B

• CE

• UL

• IC

• C-Tick

• CSA

• Wi-Fi

Dimensions

• L = 170 mm

• W = 170 mm

• H = 28 mm

D-Link DAP-2330 User Manual 90

Appendix D - Antenna Pattern

Antenna Pattern

DAP-2660

Wireless AC1200 Concurrent Dual Band PoE Access Point

Physical

Dimensions • 170 x 170 x 28 mm (6.69 x 6.69 x 1.1 inches)

Weight • 316 grams (11.14 oz) with antennas

Operating Voltage • 12 V DC +/- 10%, or 802.3af PoE4

Maximum Power Consumption • 11 Watts

Temperature • Operating: 0 to 40 °C (32 to 104 °F) • Storage: -20 to 65 °C (-4 to 149 °F)

Humidity • Operating: 10% to 90% non-condensing • Storage: 5% to 95% non-condensing

Certications • FCC

• IC

• CE

• UL

• Wi-Fi® Certied

Antenna Patterns

Orientation H-Plane E-Plane

2.4 GHz Ceiling Mounted

2.4 GHz Wall Mounted

5 GHz Ceiling Mounted

5 GHz Wall Mounted

Z Y

Wall

(E-Plane)

Floor

(H-Plane)

Z Y

Wall

(E-Plane)

Floor

(H-Plane)

Z Y

Wall

(E-Plane)

Floor

(H-Plane)

Z Y

Wall

(E-Plane)

Floor

(H-Plane)

D-Link DAP-2330 User Manual 91

Appendix D - Antenna Pattern

Contacting Technical Support

U.S. and Canadian customers can contact D-Link technical support through our web site or by phone.

Before you contact technical support, please have the following ready:

• Model number of the product (e.g. DAP-2330)

• Hardware Revision (located on the label on the device (e.g. rev A1))

• Serial Number (s/n number located on the label on the device).

You can nd software updates and user documentation on the D-Link website as well as frequently asked questions and

answers to technical issues.

For customers within the United States:

Phone Support:

(877) 453-5465

Internet Support:

http://support.dlink.com

For customers within Canada:

Phone Support:

(800) 361-5265

Internet Support:

http://support.dlink.ca

D-Link DAP-2330 User Manual 92

Appendix E - Warranty

Warranty

Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty:

• Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and

• Only for products purchased and delivered within the fty states of the United States, the District of Columbia, U.S. Possessions

or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.

Limited Warranty:

D-Link warrants that the hardware portion of the D-Link product described below (“Hardware”) will be free from material defects in workmanship

and materials under normal use from the date of original retail purchase of the product, for the period set forth below (“Warranty Period”), except

as otherwise stated herein.

• Hardware (excluding power supplies and fans): One (1) year

• Power supplies and fans: One (1) year

• Spare parts and spare kits: Ninety (90) days

The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at

D-Link’s option, to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund the actual

purchase price paid. Any repair or replacement will be rendered by D-Link at an Authorized D-Link Service Oce. The replacement hardware

need not be new or have an identical make, model or part. D-Link may, at its option, replace the defective Hardware or any part thereof with any

reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware.

Repaired or replacement hardware will be warranted for the remainder of the original Warranty Period or ninety (90) days, whichever is longer,

and is subject to the same limitations and exclusions. If a material defect is incapable of correction, or if D-Link determines that it is not practical

to repair or replace the defective Hardware, the actual price paid by the original purchaser for the defective Hardware will be refunded by D-Link

upon return to D-Link of the defective Hardware. All Hardware or part thereof that is replaced by D-Link, or for which the purchase price is refunded,

shall become the property of D-Link upon replacement or refund.

D-Link DAP-2330 User Manual 93

Appendix E - Warranty

Limited Software Warranty:

D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specications

for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90)

days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its

documentation. D-Link further warrants that, during the Software Warranty Period, the magnetic media on which D-Link delivers the Software will

be free of physical defects. The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty

will be, at D-Link’s option, to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Link’s

functional specications for the Software or to refund the portion of the actual purchase price paid that is attributable to the Software. Except as

otherwise agreed by DLink in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions

of the license granted by D-Link for the Software. Replacement Software will be warranted for the remainder of the original Warranty Period and is

subject to the same limitations and exclusions. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion

that it is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be

refunded by D-Link; provided that the non-conforming Software (and all copies thereof) is rst returned to D-Link. The license granted respecting

any Software for which a refund is given automatically terminates.

Non-Applicability of Warranty:

The Limited Warranty provided hereunder for Hardware and Software portions of D-Link’s products will not be applied to and does not cover any

refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers, or

the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being sold “As-Is” without any

warranty whatsoever including, without limitation, the Limited Warranty as described herein, notwithstanding anything stated herein to the contrary.

Submitting A Claim:

The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and the

product is within warranty, the customer shall submit a claim to D-Link as outlined below:

• The customer must submit with the product as part of the claim a written description of the Hardware defect or Software

nonconformance in sucient detail to allow D-Link to conrm the same, along with proof of purchase of the product (such as a

copy of the dated purchase invoice for the product) if the product is not registered.

• The customer must obtain a Case ID Number from D-Link Technical Support (USA 1-877-453-5465 or Canada 1-800-361-5265), who

will attempt to assist the customer in resolving any suspected defects with the product. If the product is considered defective, the

customer must obtain a Return Material Authorization (“RMA”) number by completing the RMA form. Enter the assigned Case ID

Number at https://rma.dlink.com/ (USA only) or https://rma.dlink.ca (Canada only).

D-Link DAP-2330 User Manual 94

Appendix E - Warranty

• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package

to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package.

Do not include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product

and will not ship back any accessories.

• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD

will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped

to D-Link Systems, Inc.

• USA residents send to 17595 Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that

are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common

carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link if you use an address in the United States, otherwise

we will ship the product to you freight collect. Expedited shipping is available upon request and provided shipping charges are

prepaid by the customer. D-Link may reject or return any product that is not packaged and shipped in strict compliance with the

foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to

pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance

with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.

• Canadian residents send to D-Link Networks, Inc., 2525 Meadowvale Boulevard Mississauga, Ontario, L5N 5S2 Canada. D-Link will

not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to

the customer via Purolator Canada or any common carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link

if you use an address in Canada, otherwise we will ship the product to you freight collect. Expedited shipping is available upon

request and provided shipping charges are prepaid by the customer. D-Link may reject or return any product that is not packaged

and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from the outside of

the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product that is

not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or

non-conforming. RMA phone number: 1-800-361-5265 Hours of Operation: Monday-Friday, 9:00AM – 9:00PM EST

What Is Not Covered:

The Limited Warranty provided herein by D-Link does not cover:

Products that, in D-Link’s judgment, have been subjected to abuse, accident, alteration, modication, tampering, negligence, misuse, faulty installation,

lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number

has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs;

Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment, due to act

of God, failures due to power surge, and cosmetic damage; Any hardware, software, rmware or other products or services provided by anyone

other than D-Link; and Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers,

or the liquidators expressly disclaim their warranty obligation pertaining to the product.

D-Link DAP-2330 User Manual 95

Appendix E - Warranty

While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link

Service Oce. Improper or incorrectly performed maintenance or repair voids this Limited Warranty.

Disclaimer of Other Warranties:

EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER

INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.

IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY

SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER THE

LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE

PURCHASER OF THE PRODUCT.

Limitation of Liability:

TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL

OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL,

INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK

STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT

IS CONNECTED WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK

FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF

THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF

THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NONCONFORMING PRODUCT. THE MAXIMUM

LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING

EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED

OR STATUTORY.

Governing Law:

This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or

consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This

Limited Warranty provides specic legal rights and you may also have other rights which vary from state to state.

Trademarks:

D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their

respective owners.

No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any

D-Link DAP-2330 User Manual 96

Appendix E - Warranty

derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the

United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice.

CE Mark Warning:

This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take

adequate measures.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by

one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to

operate this equipment.

802.11g operation of this product in the U.S.A. is rmware-limited to channels 1 through 11.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and

operated with minimum distance 20cm between the radiator & your body.

D-Link DAP-2330 User Manual 97

Appendix E - Warranty

The availability of some specic channels and/or operational frequency bands are country dependent and are rmware programmed at the factory to match

the intended destination. The rmware setting is not accessible by the end user.

For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local D-Link oce.

This device and it’s antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC

multi-transmitter product procedures.

Industry Canada Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1) this device may not cause interference and

2) this device must accept any interference, including interference that may cause undesired operation of the device

This device has been designed to operate with an antenna having a maximum gain of 3dBi.

Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50ohms.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful

communication.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même

si le brouillage est susceptible d’en compromettre le fonctionnement.

Caution:

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d’autres canaux n’est pas possible.

This device and it’s antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with IC multi-

transmitter product procedures.

Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une autre antenne ou transmetteur.

IMPORTANT NOTE:

IC Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with

minimum distance 20cm between the radiator and your body.

Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé

et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

D-Link DAP-2330 User Manual 98

Appendix F - Registration

Version 1.0

May 12, 2014

Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.

Registration

Table of Contents

D-Link N300 User Manual

Related Manuals

LevelOne N300 Manual

LevelOne N300 Manual

LevelOne N300 Manual

Zyxel Wireless N300 Manual

Toshiba N300 Manual

Zyxel Wireless N300 Manual

Toshiba N300 Manual

Toshiba N300 Manual