Da-Lite 24412 User Manual

Displayed below is the user manual for 24412 by Da-Lite which is a product in the Projection Screens category. This manual has pages.

INSTRUCTION BOOK FOR

UTB Contour

Tools Required for InstallationIncluded Hardware

Large Wall Bracket (47”)

(1) Screens under 104" in viewing width

(2) Screens 104" and over in viewing width

Phillips Screwdriver

Tape Measure

Pencil

Small Bottom Wall bracket (8”)

(1) Screens under 104" in viewing width

Large Bottom Wall bracket (44”)

(1) Screens 104" and over in viewing width

Frame Brackets

(1) Screens under 104" in viewing width

(2) Screens 104" and over in viewing width

#10

X ⅜"

Silver Screws (12) 832

X ⅜"

Machine Screws (4)

#10

X ⅜"

Pointed

Black Screws (Varies)

832 X ½" Fillister Screw

(1) Screens under 104" in viewing width

(2) Screens 104" and over in viewing width

1. Create a clean work area for assembly using a soft clean material.

This will protect the inner frame and ensure a clean projection

surface.

2. Unwrap frame pieces. Assemble inner frame pieces on the work

area.

3. Slide inner frame pieces together at corners. Secure inner frame

pieces with (12) #10 x

⅜

" silver screws (Figure 1).

4. Set the assembled inner frame aside. Unroll screen surface and

place it viewing side down on the clean work area.

5. Place inner frame on screen surface, screw side up.

Inner Frame & Viewing Surface Assembly

Figure 1

(12) #10 x ⅜" Screws.

Silver, Flat Tip

6. Wrap the corners of the surface around the inner frame and

hook the grommets over the corner pins (Figure 2).

Note: Make sure the screen surface is even and covering all four

corners of the inner frame before proceeding or you may see a

visible gap in the corner after the outer bezel is attached.

7. Hook the rest of the grommets over the lat head screws on all

sides (Figure 2). Please be sure the grommets clear the head of

each screw.

Note: Your screen was assembled and aligned prior to shipment.

If any realignment is necessary, the positioning of the lat head

screws can be adjusted. Using a Phillips screwdriver, rotate the

lat head screw one turn counterclockwise. Reposition screw as

needed. Secure the screw in place by slowly rotating it clockwise.

Grommets

Corner

Flat Head

Screw

Figure 2

Grommet is under

the Flat Head Screw

1. Position outer bezel pieces on all sides (Figure 3a). Gently lift and

slide each outer bezel piece around the inner frame and viewing

surface assembly (Figure 3b).

2. Align corners and insert one 832 x ⅜" screw in each corner to

attach the outer bezel onto the inner frame assembly (Figure 4).

Outer Bezel Assembly

(4) 832 x ⅜"

Machine Screws

Side View of Screen

with Bezel in Place

Bezel

Viewing

Surface

Align

Corners

Figure 3b

Figure 3a

Figure 4 Figure 5

Top Outer Bezel

Bottom Outer Bezel

Side Outer Bezel

#10 x ⅜"

Black Screws

3. Secure the outer bezel to the inner frame by inserting the #10 x

⅜" black screws into each of the large holes on all four sides of

the screen (Figure 5).

Note: The long outer bezel side with (2) or (4) small holes will be

the bottom of the screen. Do not insert screws in these holes as

they will be needed for the next step.

Outer Bezel Assembly (continued)

b. For screens 104” wide viewable and over, attach (2) frame

brackets If your screen is 104" or over in viewing area width

(Figure 7).

5. Insert 832 x ½" zinc plated illister screw into frame bracket(s)

(Figure 6 or 7). Rotate four or ive turns only.

Figure 6 — Screens Under 104" in Viewing Width

Figure 7 — Screens 104" and Over in Viewing Width

Frame Bracket

832 X ½" Fillister Screw

(2) #10 X ⅜" Pointed

Black Screws

(4) #10 X ⅜" Pointed

Black Screws

4. Depending on the size of your screen, you will have one or two

frame brackets.

a. For screens under 104” wide viewable, attach (1) frame bracket

to the bottom of the screen with (2) #10 x

⅜

" pointed BLACK

screws (Figure 6).

1. Secure the large top wall bracket to wall studs at the desired

height. Make sure the bracket is level. The top of the screen will

be 2¼" above the top of the edge of this wall bracket when

mounted. You will need at least a 3" clearance above the bracket

to hang the screen (Figure 8).

2. To install the small bottom wall bracket, you must measure the

overall height of the screen and subtract 3". Find the center point

of the top wall bracket. Using your screen height minus 3”,

measure down from the top edge of the top wall bracket and

mark the wall. This will be the center point of the bottom edge of

the bottom wall bracket. Level the bottom wall bracket and mark

the wall for the two screw holes in this bracket (Figure 8).

Installation of Screens Under 104" in Viewing Width

Figure 8 — Screens Under 104" in Viewing Width

Fillister Screw

Large Wall Bracket

Wall

Small Bottom

Wall Bracket

Small Bottom

Wall Bracket

Small Bottom

Wall Bracket

Screws Not Provided

Overall Height

of Screen Less 3"

Overall Height

of Screen

3. Attach the bottom wall bracket to the wall.

4. Lift the screen at least 3" over the top wall bracket. Lower the

screen until the frame hooks onto the top wall bracket.

5. To secure your screen against wall, locate the illister screw in the

bottom frame bracket. Tighten the screw until it touches the

bottom wall bracket, then rotate two more turns (Figure 8).

Note: This screw can be rotated up to three more turns if

stretching of viewing surface is needed.

1. Secure the (2) large top wall bracket to wall studs at the desired

height. Make sure the brackets are level. The top of the screen will

be 2¼" above the top of the edge of this wall bracket when

mounted. You will need at least a 3" clearance above the brackets to

hang the screen (Figure 9).

2. To install the large bottom wall bracket, you must measure the

overall height of the screen and subtract 3". Draw a line on your wall

between the top edges of the two top wall brackets. Mark the center

point between the top wall brackets on this line. Using your screen

height minus 3”, measure down from this center point and mark the

wall. This will be the center point of the bottom edge of the bottom

wall bracket. Level the bottom wall bracket and mark the wall for the

six screw holes in this bracket (Figure 9).

Installation of Screens 104" and Over in Viewing Width

Overall Height

of Screen

Figure 9 — Screens 104" and Over in Viewing Width

(2) Large Wall Brackets

Large Bottom Wall Bracket

Fillister Screw

(2) Large Wall Brackets

Wall

Large Bottom

Wall Bracket

Large Bottom

Wall Bracket

Screws Not Provided

Overall Height

of Screen Less 3"

3. Attach the bottom wall bracket to the wall.

4. Lift the screen at least 3" over the top wall brackets. Lower the

screen until the frame hooks onto the top wall brackets.

5. To secure your screen against wall, locate the illister screws in

the bottom frame brackets. Tighten the screws until they touch

the bottom wall bracket, then rotate two more turns (Figure 9).

Note: This screw can be rotated up to three more turns if

stretching of viewing surface is needed.

23568

A Milestone AV Technologies Brand

3100 North Detroit Street

Warsaw, Indiana 46582

P: 574.267.8101 or 800.622.3737

F: 574.267.7804 or 877.325.4832

E: info@da-lite.com

www.da-lite.com

DL–0142 (Rev. 3) 03.16

LIMITED ONE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS

Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in

materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly

operated according to Da-Lite’s instructions and are not damaged due to improper handling or treatment after shipment from the

factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered

with or repaired by a person other than authorized Da-Lite personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise.

Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,

transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.

To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use,

or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives

you speciic legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED

BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION

OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Customer Care Specialists at

3100 North Detroit Street, Warsaw, IN 46582, (574) 2678101, (800) 6223737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS

WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA-LITE WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.