Da-Lite 28271 User Manual
Displayed below is the user manual for 28271 by Da-Lite which is a product in the Projection Screens category. This manual has pages.
INSTRUCTION BOOK FOR
IDEA™ Screen
2
Tools Required For Assembly
Phillips Screwdriver Level
Rubber Mallet Measuring Tape
Hardware Provided
(7) #8 x ½” Screws
44” Wall Bracket
(2) 89”, 94¼”, 95¼” and 106” Wide Screens
28” Wall Bracket
(2) 57½”, 64”, 73½”, 80”, 81¾” and 84¾” Wide Screens
(2) LBrackets
(Not included on units with full
length marker tray)
Disclaimer
Milestone and its ailiated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete.
However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide
for every possible contingency in connection with the installation or use of this subject to change without notice or obligation of any
kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone
assumes no responsibility for accuracy, completeness or suiciency of the information contained in this document.
Da-Lite® is a registered trademark of Milestone AV Technologies. All rights reserved.
Important Safety Instructions
1. Read and understand all instructions before using.
2. Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the structure to which this component is attached can support the weight of all equipment. Reinforce
the structure as required before installing the component.
3. Use this projection screen only for its intended use as described in these instructions. Do not use attachments not recommended by the
manufacturer.
Save These Instructions
3
Preparation
Assembly Instructions for Screens with 24” Marker Tray
Note: It requires two people to assemble an IDEA Screen. To maintain optimal projected image geometry and screen alignment, a lat
and straight wall free from obstructions and angular distortions should be used.
Choose a clean work area for assembly using padded material or other soft, clean materials. The work area should be larger than the
overall screen size and directly in front of the location where the screen is to be installed.
1. Carefully unpack unit and place assembly on top of the clean
work area. The viewing surface must face up.
#8 X ½" Screws
Figure 1
Cleaning
Everyday Cleaning: The supplied foam eraser can be used to clean marks on the screen surface made by everyday dry erase marker
usage. Do not use spray cleaner in combination with the foam eraser.
Thorough Cleaning: For periodic full screen cleaning or to clean persistent marks from dry erase markers, use the supplied Da-Lite
spray cleaner and cleaning cloth. Use clean or dry sections of the microiber cloth when erasing the screen. This is important to prevent
smearing on the screen while cleaning. To clean permanent markers and other unintentional marks on the surface, use the supplied
foam eraser or the Da-Lite spray cleaner and cleaning cloth.
2. Center aluminum tray to the bottom of frame and attach with (3)
of the provided #8 x ½” screws. Insert screws through the tray into
the groove (Figure 1).
4
Wall Mounting Instructions for Screens with 24” Marker Tray
NOTE: The screen is shipped with two wall brackets. Screens in
widths of 88” and below receive (2) 28” wall brackets. Screens
above 88” in width receive (2) 44” wall brackets. Use appropriate
mounting hardware for the wall type and to accommodate for
the screen’s hanging weight (Figure 2).
1. Secure the two wall brackets to wall studs at the desired height.
The outside edge of each wall bracket must be no greater than
5” away from the left and right edges of the frame. You will need
at least 1” clearance above the drilled holes to hang the screen
(Figure 2) .
2. To install the (2) L-brackets, you must measure the overall height
of the screen frame and subtract 1⅛”. Using that dimension,
measure down from the top edge of the wall brackets and mark
the wall for two screw holes. The outside edge of each L-bracket
must be no greater than 5” away from the left and right edges of
the screen frame (Figure 2).
3. Secure the two L-brackets to the wall at the marked locations. The
longest side of the two L-brackets should be pointing upwards
when secured in order to hide the L-brackets behind the screen
frame once the screen is installed.
Wall Brackets
LBracket
No More
than 5”
No More
than 5”
No More
than 5”
Figure 2
Screws (Not Supplied)
5
Wall Mounting Instructions for Screens with 24” Marker Tray (continued)
4. This step requires two people. Hang the screen on the wall
brackets. There is a lip on the back of the frame that wedges itself
into the wall brackets once fully installed. Ensure that the screen
clears the L-brackets and that the screen weight is on the wall
brackets, not the L-brackets.
5. Tap the bottom of the two L-brackets with the rubber mallet until
they make contact with the frame. Secure the two L-brackets to
the frame with the remaining (4) #8 x ½” screws (Figure 3).
#8 X ½" Screws
Figure 3
6. Attach bottom of screen to wall through the mounting holes
located under the tray.
6
Assembly Instructions for Screens with Full Length Tray
1. Carefully unpack unit and place frame assembly on top of the
clean work area. The viewing surface must face up.
2. Center the marker tray to the bottom of the frame and attach
with (7) of the provided #8 x ½” screws (Figure 4). Insert screws
through the tray into the groove.
Viewing Surface
Aluminum Tray
#8 X ½" Screws
Figure 4
7
Wall Mounting Instructions for Screens with Full Length Tray
NOTE: The screen is shipped with two wall brackets. Screens
in widths of 88” and below receive (2) 28” wall brackets.
Screens above 88” in width receive (2) 44” wall brackets. Use
appropriate mounting hardware for the wall type and to
accommodate for the screen’s hanging weight.
1. Secure the two wall brackets to wall studs at the desired
height. The outside edge of each wall bracket must be no
greater than 5” away from the left and right edges of the
screen frame. You will need at least 1” clearance above the
drilled holes to hang the screen.
Figure 5
Screws (Not Supplied)
Wall Brackets
2. This step requires two people. Hang the screen on the wall
brackets (Figure 5). There is a lip on the back of the frame that
wedges itself into the wall brackets once fully installed.
3. Attach bottom of screen to wall through the mounting holes
located under the tray (Figure 5).
No More
than 5”
No More
than 5”
28407
A BRAND OF MILESTONE AV TECHNOLOGIES | www.milestone.com
P 800.622.3737 / 574.267.8101 F 877.325.4832 / 574.267.7804
E info@da-lite.com
In British Columbia, Milestone AV Technologies ULC carries on business as MAVT Milestone
AV Technologies ULC.
©2018 Milestone AV Technologies. DL0488 (Rev. 6) 01.18
Da-Lite is a registered trademarks of Milestone AV Technologies. All other brand names or
marks are used for identiication purposes and are trademarks of their respective owners.
All patents are protected under existing designations. Other patents pending.
LIMITED FIVE YEAR WARRANTY ON DA-LITE IDEA™ PRODUCTS ONLY
Milestone AV Technologies LLC warrants these Da-Lite branded products to the original purchaser only, to be free from defects in materials and
workmanship for a period of ive (5) years from the date of purchase by the original purchaser; provided they are properly operated according
to Da-Lite’s instructions and are not damaged due to improper handling or treatment after shipment from the factory.
This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage,
or which has been tampered with or repaired by a person other than authorized Da-Lite personnel.
Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise. Returns
for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite, transportation expenses
to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.
To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use, or
merchantability, that may be mandated by statute or rule of law are limited to the ive (5) year warranty period. This warranty gives you speciic
legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE
LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT,
OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.
In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Customer Care Specialists at 3100
North Detroit Street, Warsaw, IN 46582, (574) 2678101, (800) 6223737.
IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS
WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA-LITE WRITTEN INSTRUCTIONS.
Keep your sales receipt to prove the date of purchase and your original ownership.