Da-Lite 28848V User Manual

Displayed below is the user manual for 28848V by Da-Lite which is a product in the Projection Screens category. This manual has pages.

INSTRUCTION BOOK FOR

Parallax™ Screen

Tools Required for Installation

Included Hardware

Phillips Screwdriver Tape MeasurePencil

Large Wall Bracket (47" Long)

Installation screws not included

Quantities vary by screen size:

Screens 80" and smaller viewing width = 1

Screens over 80" to 96" viewing width = 2

Screens over 96" viewing width = 3

Small Wall Bracket (8" Long)

Installation screws not included

Quantity = 1. Only for screens 80" and smaller viewing width.

#8 Stud with Shoulder (8 each) Black Flat Head Screw (12) Elastic Ring

(1 Pack - Usage Varies by Screen Size)

Foam Sheet (1)

Gloves (2 pair)

Disclaimer

Milestone and its ailiated corporations and subsidiaries

(collectively "Milestone"), intend to make this manual accurate

and complete. However, Milestone makes no claim that the

information contained herein covers all details, conditions or

variations, nor does it provide for every possible contingency in

connection with the installation or use of this subject to change

without notice or obligation of any kind. Milestone makes no

representation of warranty, expressed or implied, regarding the

information contained herein. Milestone assumes no

responsibility for accuracy, completeness or suiciency of the

information contained in this document.

Da-Lite® is a registered trademark of Milestone AV Technologies.

Material Handling Guidelines

CAUTION: Handle screen surface with care. Ambient light rejecting screen surfaces are delicate and should remain lat at all

times.

• Carefully and evenly unroll screen surface to ensure latness.

• Do not fold, stretch or crease screen surface.

• Do not allow objects to rest on screen surface.

• Do not puncture screen surface.

1. Unwrap the frame pieces. Assemble frame pieces on provided

foam sheet. This will help keep the frame clean and protect it

from scratches.

NOTE: The frame pieces are labeled “top” and “bottom”. Be

sure the frame pieces are assembled according to the labels.

This will ensure the attachment pattern on the frame and

screen surface will match.

Figure 1 (Rear View)

Frame Assembly

Cleaning

Parallax screen surface can be cleaned as follows:

Using a white clean cloth (100% cotton preferred) that is dampened with clean water, gently wipe the area in a horizontal direction. Do

not wipe in a vertical direction or with a circular motion. Using a dry 100% cotton cloth, wipe screen surface dry in horizontal direction

after each cleaning. Windex Original spray cleaner can be used on tough to clean areas.

2. Slide the frame pieces together at corners.

NOTE: The frame assembly holes may not appear to it

properly at the corners until all fasteners have been attached.

Once fasteners are attached, the frame corners will be drawn

in for a proper it.

3. Secure frame pieces with black lat head screws provided. Do

not tighten screws until all are started. See Figure 1.

4. Attach the eight #8 studs to the back of the frame in the

predrilled holes.

Black Flat Head Screws

#8 Studs

1. Unpack screen surface.

CAUTION: Handle screen surface with care. See Material

Handling Guidelines.

2. Locate the top of the screen surface. "Top" will be labeled on

the back of the surface and should be matched with the "top"

of the frame.

Surface Attachment

3. Remove foam and unroll screen surface evenly on the back

of the frame. Make sure that the perimeter of the screen

surface is resting on the frame. See Figure 2.

4. At the top right corner, insert an elastic ring through the hole

in the screen surface and secure it over the stud. Repeat this

action for the other stud in the top right corner. See Figure 3.

Figure 2

Figure 3a Figure 3b

Figure 3c Figure 3d

Reinforcement tabs will be

on the back of the surface

Surface Attachment (continued)

5. Repeat Step 4 for the remaining three corners of the screen.

Use the sequence shown in Figure 4.

6. Insert one elastic ring into the center hole on the right, left,

top and bottom of the screen surface and secure it over the

stud. Use the sequence shown in Figure 4.

Figure 4

7. Start at the top right corner and work counter clockwise

inserting an elastic ring into the hole in the screen surface

and secure it over the stud. Repeat action until all holes have

elastic rings secured over the studs.

NOTE: Having leftover elastic rings is typical. You wil have

more rings than required.

3 1

2 4

Installation Method 1 (Screens 80" And Smaller In Viewing Width)

1. Secure the wall bracket to wall studs at the desired height.

Make sure the bracket is level. The top of the frame will be

1/8" above the top of the wall bracket when mounted. You will

need at least 5/8" clearance above the bracket to hang the

screen. Figures 5, 6, and 7 show the proper orientation for the

supplied wall brackets.

2. To install the lower wall bracket, you must measure the

overall height of the screen frame and subtract 15/8". Using

that dimension, measure down from the top edge of the wall

bracket and mark the wall for two screw holes. The holes

should be centered within the frame and 6" apart. Refer to

Figure 6.

3. Attach the small wall bracket to the wall. Refer to Figure 7 for

proper orientation. Do not tighten the screws completely. The

bracket should slide up and down easily.

4. Position the screen with the attached surface onto the top

wall bracket. Push down at the center

of the bottom frame rail to hook onto the lower wall bracket.

Refer to Figure 7.

Figure 5

Small Wall Bracket

1Piece

Large Wall

Bracket

1Piece

Figure 7

Lift

Wall

Installation

There are three methods of installation based on the size of the

screen. Measure the width of the viewing area of your screen

and refer to the appropriate method of installation below. The

wall bracket diagram shows the type and quantity of bracket(s)

supplied based on the size of the screen.

Method 1: Screens 80" and smaller in viewing width.

Method 2: Screens over 80" up to 96" in viewing width.

Method 3: Screens over 96" in viewing width.

Figure 6

Large Wall Bracket

Small Wall Bracket

Overall Height Less 1 ⅝"

Overall

Height

Installation Method 2 (Screens Over 80" Up To 96" In Viewing Width)

1. Secure the wall bracket to wall studs at the desired height.

Make sure the bracket is level. The top of the frame will be

1/8" above the top of the wall bracket when mounted. You will

need at least 5/8" clearance above the bracket to hang the

screen. Figure 8 and 9 show the proper orientation for the

supplied wall brackets.

2. To install the bottom large wall bracket, you must measure

the overall height of the screen frame and subtract 1/2". This

is the dimension from the top of the upper wall bracket to the

bottom of the bottom wall bracket. See Figure 9.

3. Position the screen with the attached surface onto the top

wall bracket as shown in Figure 9. Push down at the center

of the bottom frame rail to hook onto the lower wall bracket.

Figure 8

Large Wall

Bracket

2Pieces

Installation Method 3 (Screens Over 96" In Viewing Width)

1. Secure the wall brackets to wall studs at the desired height.

Make sure the brackets are level. The top of the frame will be

1/8" above the top of the wall bracket when mounted. You will

need at least 5/8" clearance above the bracket to hang the

screen. Figure 9 and 10 show the proper orientation for the

supplied wall brackets.

2. To install the bottom large wall bracket, you must measure

the overall height of the screen frame and subtract 1/2". This

is the dimension from the top of the upper wall bracket to

the bottom of the lower wall bracket. See Figure 9.

3. Position the screen with the attached surface onto the top

wall bracket as shown in Figure 9. Push down at the center

of the bottom frame rail to hook onto the lower wall bracket.

Figure 10

Large Wall

Brackets

3Pieces

Figure 9

Overall Height

Overall Height Less ½"

Wall

LIMITED ONE YEAR WARRANTY ON DALITE PRESENTATION PRODUCTS

Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in

materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly

operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the

factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered

with or repaired by a person other than authorized Da-Lite personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise.

Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,

transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.

To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use,

or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives

you speciic legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED

BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION

OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Customer Care Specialists at

3100 North Detroit Street, Warsaw, IN 46582, (574) 2678101, (800) 6223737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DALITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS

WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DALITE WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

28841

A BRAND OF MILESTONE AV TECHNOLOGIES | www.milestone.com

P 800.622.3737 / 574.267.8101 F 877.325.4832 / 574.267.7804

E info@da-lite.com

In British Columbia, Milestone AV Technologies ULC carries on business as MAVT Milestone

AV Technologies ULC.

Da-Lite is a registered trademarks of Milestone AV Technologies. All other brand names or

marks are used for identiication purposes and are trademarks of their respective owners.

All patents are protected under existing designations. Other patents pending.