Da-Lite 29206 User Manual
Displayed below is the user manual for 29206 by Da-Lite which is a product in the Projection Screens category. This manual has pages.
INSTRUCTION BOOK FOR
Tensioned Wireline™
Advantage® Electrol®
2
Tools Required for Installation
1. The case provides multiple attachment points for bolts,
cables, or threaded rod. Page 4 shows threaded rod
installed. The variable position-mounting bracket may be
located anywhere along the length of the case. It is
recommended to keep the brackets spaced evenly enough
to distribute the weight of the screen. One mounting bracket
is required for every 4' of case length.
2. Tighten bolts until trim lange is lush with ceiling.
NOTE: For proper operation, screen assembly must be level
after installation.
3. Remove 2 screws to open junction box. Install electrical
connections that apply to your unit. Make sure to review the
wiring diagram for proper hook up. Replace junction box
cover and secure with 2 screws.
NOTE: Please Note: Motor Operator Projection Screen Model
WAD must be installed in accordance with the requirements
of the Local Building Codes, the Canadian Electrical Code
(CEC), CAN/CSA C22.1 and the National Electric Code (NEC),
NFPA 70. An appropriate disconnect device shall be
provided as part of the building installation.
If your case was ordered in advance of the screen and roller
assembly, your installation is now complete. Continue to
step 4 if your Tensioned Wireline Advantage Electrol was
ordered as a complete unit.
4. Carefully remove paper and tape from roller assembly
CAUTION! Do not use a knife or sharp object to cut tape;
you will damage the screen. Pull orange string.
ATTENTION! Ne coupez pas le ruban adhésif sur la toile
avec un couteau ou un outil tranchant. Retirez à la main.
5. Use supplied 1/8" hex key to remove silver shipping brackets
attached to slat and screen case.
6. Test installation by running screen up and down a few times.
Be prepared to stop screen should any objects obstruct the
movement of the screen. To prevent damage to the motor,
the standard duty cycle is 1 minute 30 seconds on and 60
minutes of.
7. The screen comes set standard with 18" of wire drop out of
the case.
Case Installation
Important Safety Instructions
When using your video equipment, basic safety precautions
should always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so it will not be tripped over, pulled or contact
hot surfaces.
3. If an extension cord is necessary, a cord with a current rating at
least equal to that of the appliance should be used. Cords rated
for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric shock
when the appliance is used subsequently.
5. The use of an accesory attachement not recommended by the
manufacturer may cause a risk of ire, electric shock, or injury to
persons.
6. Do not allow children to play with ixed controls. Keep remote
controls away from children.
7. Frequently examine the installation for imbalance and signs of
wear or damage to cables. Do not use if repair or adjustment is
necessary.
Save These Instructions
Pre-Installation
1. Carefully unpack case from shipping crate.
2. Set aside the Installation Kit. Items inside will be used during
installation.
3. Make sure to recheck measurement of case for proper
installation clearance.
4. Remove any protective foam from case.
5. If necessary. adjust hanger brackets with a 3/4" open wrench
or socket driver.
3/4“ Open Wrench
or Socket Driver
1/8“ Hex Key
(included)
3
Installation
Variable Position
Mounting Brackets
Electrical
Junction Box
Electrical
Junction Box
Screen Roller
Access Door
Audience
Side
Self-Trimming
Flange
(Suggested) 1/2"
Threaded Rod
(Not Included)
Attached to
Mounting Bracket
Finished
Ceiling
Self-Trimming
Flange
12 ⁄"
13 ⅛"
11"
9 ⅛"
11 ⁄"
4
1. Run screen in down direction until it reaches lower limit and
stops.
2. Press and hold both UP and DOWN arrows simultaneously until
screen jogs.
3. Run screen to new desired lower limit position by pressing
DOWN arrow on remote
Note: Motor will run in momentary contact mode while in this
procedure. If you go to far down you can press up and move
to the next step.
4. Press and MY (STOP) button until the screen jogs to conirm
new limit.
1. Run screen in down direction until it reaches lower limit and
stops.
2. Press and hold both UP and DOWN arrows simultaneously until
screen jogs.
3. Run screen to new desired lower limit position by pressing UP
arrow on remote.
Note: Motor will run in momentary contact mode while in this
procedure. If you go to far down you can press down and
move to the next step.
4. Press and MY (STOP) button until the screen jogs to conirm
new limit.
Note: The entire screen must be unrolled from the large roller
for proper tensioning.
Screen Adjustment
More Screen Drop
Less Screen Drop
Surface travel is set to stop automatically with 18" of wire travel out of the case. Use the supplied radio frequency remote control to
make adjustments to the amount of travel.
Figure 1
CAUTION: Do not adjust for more than 29' of cable drop.
ATTENTION! Ne pas régler plus de 884 centimètres de chute
de câble
5
240V Wiring Diagram
120V Wiring Diagram
Power Input
120VAC / 60Hz
Black (Hot)
White (Common)
Green
(Ground)
Ground
Lug
Power Input
220VAC / 50Hz
Brown (Hot)
Blue (Common)
Green/Yellow
(Ground)
Ground
Lug
6
Troubleshooting
Visit www.da-lite.com to ind installation and troubleshooting
tutorials. You will also ind a link to Live Chat for interactive
support.
You can contact us by email at info@da-lite.com or by phone
at 800.622.3737 or 574.267.8101 with any additional
troubleshooting questions.
Symptom Cause Solution
Screen will not operate
and motor does not hum.
Incorrect line voltage. Verify 115125V (or 220240V). If insuicient voltage, rewire
incoming electric line.
Blown fuse. Replace fuse.
Tripped circuit breaker. Reset circuit breaker.
No power to junction. Check above. Tighten all loose wire connections.
Correct any improper connections.
Screen will not operate
and motor does not hum.
Power at junction box.
Thermal overload tripped. Let motor cool down for 50 minutes. Try again.
Defective motor, limit switch or capacitor. Replace motor assembly. NOTE: Motor is a sealed assembly.
Capacitor burned out. Replace motor assembly.
Screen does not stop
at correct position. Limit switch out of adjustment. See Screen Adjustment section.
Noise.
NOTE: Screen will operate
with a low pitched hum.
Squeaking, rubber end plug rubbing on motor. Center roller in case.
Grinding. Foreign object in screen
rubbing on roller or fabric. Remove.
Gear noise. Replace motor assembly.
Coasting. Defective brake. Replace motor assembly.
Fabric hangs crooked.
Screen not installed properly. Check for level and plumb.
Fabric is damaged. Replace fabric.
7
29355
A Milestone AV Technologies Brand
3100 North Detroit Street
Warsaw, Indiana 46582
P: 574.267.8101 or 800.622.3737
F: 574.267.7804 or 877.325.4832
E: info@da-lite.com
www.da-lite.com
DL–0620 11.15
© 2015 Milestone AV Technologies LLC. Printed in U.S.A.
LIMITED ONE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS
Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in
materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly
operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the
factory.
This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered
with or repaired by a person other than authorized Da-Lite personnel.
Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise.
Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,
transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.
To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use,
or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives
you speciic legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED
BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION
OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.
In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Customer Care Specialists at
3100 North Detroit Street, Warsaw, IN 46582, (574) 2678101, (800) 6223737.
IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS
WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA-LITE WRITTEN INSTRUCTIONS.
Keep your sales receipt to prove the date of purchase and your original ownership.