Da-Lite 34538LSR User Manual

Displayed below is the user manual for 34538LSR by Da-Lite which is a product in the Projection Screens category. This manual has pages.

INSTRUCTION BOOK FOR

Tensioned Advantage® Electrol®

Original Instructions

Important Safety Instructions

Disclaimer

Milestone and its ailiated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete.

However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide

for every possible contingency in connection with the installation or use of this subject to change without notice or obligation of any

kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone

assumes no responsibility for accuracy, completeness or suiciency of the information contained in this document.

When using your video equipment, basic safety precautions

should always be followed, including the following:

1. Read and understand all instructions before using.

2. Maximum surrounding air temperature 122°F (50°C).

3. Main disconnect must be incorporated in the ixed wiring in

accordance with the wiring rules.

4. Rated for indoor use only.

5. Use copper rated conductors rated 167°F (75°C) or higher.

6. If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualiied persons in

order to avoid hazard.

7. Supplied drive is only intended for use in Da-Lite screen models

Advantage, Contour, and Cosmopolitan.

8. Position the cord so that it will not be tripped over, pulled, or

contact hot surfaces.

9. If an extension cord is necessary, a cord with a current rating at

least equal to that of the appliance should be used. Cords rated

for less amperage than the appliance may overheat.

10. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric shock

when the appliance is used subsequently.

11. The use of an accessory attachment not recommended by the

manufacturer may cause a risk of ire, electric shock, or injury to

persons.

12. Failure to provide adequate structural strength for this

component can result in serious personal injury or damage to

equipment! It is the installer’s responsibility to make sure the

structure to which this component is attached can support the

weight of all equipment. Reinforce the structure as required

before installing the component.

13. Use this projection screen only for its intended use as described

in these instructions. Do not use attachments not recommended

by the manufacturer.

Save These Instructions

Tensioned Advantage® Electrol® Suggested Methods of Installation

⅜" Threaded Rod

(Not Supplied)

Hanger Bracket

Electrical

Junction Box

Motor

End

Variable Position

Mounting Bracket

Audience Side

6 ⁄"

6 ⁄"

7 ¾"

⅜" Threaded Rod

(Not Included)

Attached To

Mounting Bracket

Self-Trimming

Flange Finished

Ceiling

7 ¾"

6 ⁄"

6 ⅜"

3 ⁄"

7 ⁄"

6 ⁄"

Method 1

Method 2

9 ¼"

Tools Required for Installation

1. Hang case and attach to support structure with bolts. See

Suggested Methods of Installation.

2. Tighten bolts until trim lange is lush with ceiling.

NOTE: For proper operation, case must be levelled side to

side and front to back.

3. Remove 2 screws to open junction box. Install electrical

connections that apply to your unit. Make sure to review the

wiring diagram for proper hook up. Replace junction box

cover and secure with 2 screws.

NOTE: Must be installed in accordance with the requirements

of the Local Building Codes, the Canadian Electrical Code

(CEC), CAN/CSA C22.1 and the National Electric Code (NEC),

NFPA 70.

Case Installation

Pre-Installation

1. Carefully unpack case from shipping carton.

2. Set aside the Installation Kit. Items inside will be used

during installation.

3. Make sure to recheck measurement of case for proper

installation clearance.

4. Remove any protective foam covering the outside

of the case.

1/2“ and 5/16" Open Wrench

or Socket Driver

1/8” Hex Key

(included)

5. For shipping purposes, foam is also inserted between the

roller brackets and end caps (Figure 1). Remove these foam

blocks from the ends.

6. Remove the hanger brackets from the top of the case

using a 1/2" wrench. Do not discard the hardware; it will be

used during case installation to re-attach the hanger

brackets for mounting.

If your case was ordered in advance of the screen and

roller assembly, your installation is now complete.

Continue to step 4 if your Tensioned Advantage Electrol

was ordered as a complete unit.

4. Use a 5/16" socket or wrench and the supplied 1/8" hex key to

remove silver shipping brackets attached to slat and screen

case.

5. Test installation by running screen up and down a few times.

Be prepared to stop screen should any objects obstruct the

movement of the screen. To prevent damage to the motor,

the standard duty cycle is 1 minute on and 3 minutes of.

Follow these steps if your screen and roller assembly was ordered separately from the case.

1. Remove the access door. First, remove the 2 screws from the

ends using a #2 Phillips screwdriver. Be sure to support the

door during this step to avoid injury. Then lift the door slightly

and pull away from the edge of the case (Figure 1).

2. Carefully unpack screen and roller assembly. Use

a 5/16" socket

or wrench and a #2 Phillips Screwdriver

to remove shipping

brackets attached to slat. Remove fabric and roller assembly

from shipping board using a 1/2" wrench. Leave packing paper

on roller.

3. To install screen and roller assembly, loosen (but do not

remove) four 1/420 nuts securing pin end bracket (opposite

end from the junction box) to the case housing. Slide the pin

end bracket towards the end of the case (Figure 2).

4. Insert the motor end square shaft into the motor end bracket

(junction box end) and secure with the cotter pin (Figure 2).

5. Moving to the pin end of the case, slide the pin end bracket

until the hole its securely over the pin and secure with the

cotter pin. Tighten the 1/420 nuts on the pin end bracket

securely (Figure 2).

6. Complete electrical hook-up by snapping motor wire

connector into case connector (Figure 2).

8. Test installation by running screen up and down a few times.

Be prepared to stop screen should any objects obstruct the

movement of the screen. To prevent damage to the motor, the

standard duty cycle is 1 minute on and 3 minutes of.

9. Re-install the access door. Procedure is the reverse of step 1

listed above.

Screen And Roller Assembly Installation

#2 Phillips Screwdriver

Tools required for screen and roller assembly:

1/2“, 1/4" and 5/16"

Open Wrench

or Socket Driver

Motor Mount

Bracket

Motor Power

Connector

1/420 Nuts

Access Door Screws

Foam Blocks

Pin End

Figure 1

Motor End

Cotter Pins

Motor

Figure 2

4. Insert motor in tube with seam of tube lined up with drive wheel and collar cutouts.

Seam of Tube

Motor Collar

Motor Drive Wheel

Motor Key

Replacement Motor Instruction

Rated torque of model DL45E10/26 is 10 N/m with a duty cycle of 1 min. on / 3 min. of.

Rated torque of model DL45EQ6/28 is 6 N/m with a duty cycle of 1 min. on / 3 min. of.

Motor is intended for use in Da-Lite screens incorporating a 3.00" and 3.25" roller diameter.

1. Make sure motor collar is on motor.

2. Collars keyway must line up with the key on the motor.

3. Secure motor drive wheel on output shaft of motor and insert retaining clip.

Screen And Roller Assembly Installation (continued)

RJ45

Receptacle

RJ22

Output

(QAUX)

RJ22

Inputs

(QEYE)

Up (Dry Contact)

Down (Dry Contact)

Common (Both)

Bus (Bus)

5V (Bus)

STOP

DOWN

BUS

COM

Front of

Wall Switch

Bus

STOP

DOWN

BUS

COM

LED

Up Limit

Tactile Button

Down Limit

Tactile Button

Back of

Wall Switch

Tensioned Advantage® Electrol® Installation for 120V Screens

RJ22 Pin-Outs (Tab Is Facing Down)

Standard RJ22 can be used in place of RJ14 cable

Bus (RP Data)

+12V

RQ Clock

RQ Data

+5V

Ground

Yellow

Green

Red

Black

White

Blue

RJ45 Pin-Outs (Tab Is Facing Down)

+12V

Manual 2

Ground

Manual 1

RQ Clock

Bus (RP Data)

RQ Data

+5V

Blue

Green

Yellow

Red

Black

Orange

Purple

Brown

120V Wiring Diagram

3-conductor 2024 gauge wire can be used in place of the

supplied RJ14 cable to connect the wall switch. Connect the BUS

terminals on the wall switch to the corresponding BUS terminals

on the splitter board.

STOP

DOWN

BUS

COM

Power Input 120VAC / 60Hz

Green (Ground)

(Ground–Must be Connected

to Building Ground)

Black

(Hot)

White

(Common)

Power

Wire

Data

Cable

RJ45 Jack

RJ22 Jack

(Connection to

Wall Switch)

RJ22

Jack

RJ14 Pin-Outs (Tab Is Facing Down)

Supplied RJ14 cable

Bus (RP Data)

RQ Data

+5V

Ground

White

Green

Red

Black

Installation Video

To view a video of this installation,

visit http://youtu.be/t2ZQ9PVAhEg

or use the QR code below.

IMPORTANT NOTE: The wall switch is REQUIRED to make any

limit switch adjustments, EVEN if a third party control system is

used. Therefore, it is advised to wire the switch or provide a

3-conductor connection that is accessible..

Tensioned Advantage® Electrol® Installation for 220V Screens

RJ45

Receptacle

RJ22

Output

RJ22

Inputs

Up (Dry Contact)

Down (Dry Contact)

Common (Both)

Bus (Bus)

5V (Bus)

STOP

DOWN

BUS

COM

Front of

Wall Switch

Bus

STOP

DOWN

BUS

COM

LED

Up Limit

Tactile Button

Down Limit

Tactile Button

Back of

Wall Switch

RJ22 Pin-Outs (Tab Is Facing Down)

Standard RJ22 can be used in place of RJ14 cable

Bus (RP Data)

+12V

RQ Clock

RQ Data

+5V

Ground

Yellow

Red

Green

Black

White

Blue

RJ45 Pin-Outs (Tab Is Facing Down)

+12V

Manual 2

Ground

Manual 1

RQ Clock

Bus (RP Data)

RQ Data

+5V

Blue

Green

Yellow

Red

Black

Orange

Purple

Brown

220V Wiring Diagram with Operation & Limit Adjustment

Wall Switch

3-conductor 2024 gauge wire can be used in place of the

supplied RJ14 cable to connect the wall switch. Connect the BUS

terminals on the wall switch to the corresponding BUS terminals

on the splitter board.

IMPORTANT NOTE: The wall switch is REQUIRED to make any

limit switch adjustments, EVEN if a third party control system is

used. Therefore, it is advised to wire the switch or provide a

3-conductor connection that is accessible.

STOP

DOWN

BUS

COM

Power Input 220VAC / 50Hz

Green / Yellow (Ground)

Blue

(Hot)

Brown

(Common)

Power

Wire

Data

Cable

RJ45 Jack

RJ22 Jack

(Connection to

Wall Switch)

RJ22

Jack

RJ14 Pin-Outs (Tab Is Facing Down)

Supplied RJ14 cable

Bus (RP Data)

RQ Data

+5V

Ground

White

Green

Red

Black

Tensioned Advantage® Electrol® Installation for 220V Screens (continued)

220V Wiring Diagram with European Style Wall Switch

Use 3-conductor 2024 gauge wire for wall switch connections.

IMPORTANT NOTE: The European style wall switch is for

operation only and CANNOT be used to make limit switch

adjustments. Therefore, it is advised to wire the limit adjustment

switch or provide a 3-conductor connection that is accessible.

Power Input 220VAC / 50Hz

Green / Yellow (Ground)

Blue

(Hot)

Brown

(Common)

Power

Wire

Data

Cable

RJ45 Jack

Black (Down)

White (Common)

Red (Up)

Red

Black

White

Inputs

Output

Black (Down)

White (L / Common)

Red (Up)

Push Down on Tab to

Insert Wire

STOP

DOWN

BUS

COM

RJ22 Jack

(Connection to

Wall Switch)

RJ22

Jack (QEYE)

Optional Built-In Video Projector Interface

5/12 Volt

Screen Trigger

on Projector

Black

Red

VPI Trigger

Module

CAUTION: The projector must be turned of before

connecting the trigger wires to the projector. Failure to

do so may damage the controller.

ATTENTION: Le projecteur doit être éteint avant de

brancher les ils de déclenchement à celui-ci. Tout

manquement à cette instruction pourrait endommager le

contrôleur.

Use 2-conductor 1824 gauge wire to extend the low voltage

connection from the projector’s 5 or 12-volt screen trigger output

to the length required to reach the VPI.

NOTE: When extending the low voltage connection from the

projector’s screen trigger output polarity does not matter. The

red and black wires from the VPI are interchangeable.

IMPORTANT NOTE: The wall switch is REQUIRED to make any

limit switch adjustments, EVEN if a third party control system is

used. Therefore, it is advised to wire the switch or provide a

3-conductor connection that is accessible.

3-conductor 2024 gauge wire can be used in place of the

supplied RJ14 cable to connect the wall switch. Connect the BUS

terminals on the wall switch to the corresponding BUS terminals

on the splitter board.

See 120V or 220V wiring diagram for complete wiring

instructions.

Screen Adjustment

If your Tensioned Advantage Electrol was ordered as a complete unit, the up and down limits were pre-set by Da-Lite. If your screen and

roller assembly was ordered separately from the case, or if general adjustment is needed, please follow the steps below and refer to the

Wiring Diagram.

1. Locate the wall switch and remove the cover plate from the

wall switch and remove the switch from the junction box.

2. Locate the two tactile buttons on the back of the switch.

They are black round buttons on silver plates.

3. To adjust the down limit switch, press and hold the down

tactile button until the LED on the back of the switch turns

solid red. This will put the motor in limit set mode. Turn the

wall switch over and use the down button on the front of the

switch. Press and hold the down button until the desired

down position is reached. If you travel too far down, press the

up button to move the screen upward. If you press and let go

of either the up or down buttons, the motor will do a small

jog in that direction for ine adjustment of the screen. Once

the desired position is reached, turn the switch over; press

and hold the down tactile button until the LED on back of

switch blinks red twice. The down limit is now set.

CAUTION: Do not adjust for more drop than what was

ordered. At least 11/2 wraps of fabric must remain on

the roller.

ATTENTION! N'efectuez pas de réglage pour obtenir un

déroulement supérieur à celui commandé. Au moins 1 à

1/2 tour de toile doit être maintenu sur le cylindre.

NOTE: If the screen is in limit set mode and no buttons are

pushed for 20 seconds, the LED on the back of the wall

switch will turn of, the motor will return to run mode and no

changes will be saved. If this occurs, return to step 3 for down

limit adjustment or step 4 for up limit adjustment.

NOTE: All screens except Parallax standard with 12" black

drop at the top. Screens with Parallax surface standard with 2"

of black drop at the top.

4. To adjust the up limit switch, press and hold the up tactile

button until the LED on the back of the switch turns solid

green. This will put the motor in limit set mode. Turn the wall

switch over and use the up button on the front of the switch.

Press and hold the up button until the desired up position is

reached. If you travel too far up, press the down button to

move the screen downward. If you press and let go of either

the up or down buttons, the motor will do a small jog in that

direction for ine adjustment of the screen. Once the desired

position is reached, turn the switch over; press and hold the

up tactile button until the LED on back of switch blinks green

twice. The up limit is now set.

CAUTION: Adjusting the down limit switch for less drop

by more than 6" can cause the screen surface to lose

proper tensioning.

ATTENTION! LE FAIT D'AJOUTER NE DÉROULEZ PAS

TROP L'ÉCRAN PLUS DE 15 CM (6PO) AUX

INTERRUPTEURS DE FIN DE COURSE PEUT FAIRE

PERDRE LA BONNE TENSION À LA SURFACE DE L'ÉCRAN.

5. To test the limit switch settings, press and release the up or

down buttons on the switch to operate the screen.

6. Replace the switch and cover plate on the wall.

IMPORTANT NOTE: The wall switch is REQUIRED to make

any limit switch adjustments, even if a third party control

system is used. Therefore, it is advised to wire the switch or

provide a 3-conductor connection that is accessible.

STOP

DOWN

BUS

COM

Front of Wall

Switch

STOP

DOWN

BUS

COM

LED

Up Limit

Tactile Button

Down Limit

Tactile Button

Back of

Wall Switch

Third Party Control

Control Panel

A control panel may be connected to the splitter board by using

the dry contact Up, Down and Common connections. The

control panel must provide a momentary, dry contact closure of

at least 1/2 second.

1. Use 3-conductor 2024 gauge wire to connect the control panel

to the splitter board.

2. A momentary closure across the common and up wires will be

an “up” command.

3. A momentary closure across the common and down wires will

be a “down” command.

4. A momentary closure across the common, up and down wires

will be a “stop” command.

Operation of Screen

Operation & Limit Adjustment Wall Switch

1. Press ”DOWN” button on screen switch and screen will deploy

out of case in downward direction.

2. Press “STOP “button on screen switch and screen will stop if in

movement.

3. Press “UP” button on screen switch and screen will retract

upward into case.

“Up”

Button

“Stop”

Button

“Down”

Button

“Up”

Button

“Down”

Button

European Style Wall Switch (220V models only)

1. Press ”DOWN” button on screen switch and screen will deploy

out of case in downward direction.

2. Press “UP” button on screen switch and screen will retract

upward into case.

Up (Dry Contact)

Down (Dry Contact)

Common (Both)

Bus (Bus)

5V (Bus)

Conditions for Transportation and Storage

• Temperature: Between 40 - 100F (5 - 40C)

• Relative Humidity: 30% to 70%, non-condensing

• Always keep the projection screen horizontal during transport

and storage

• Make sure the entire package is supported when stored

• Do not stack more than six projection screens on top of each other

• Make sure the heaviest package is places at the bottom of the stack

Screen surface should be allowed to air out once every two months, or otherwise used on a regular basis, if the temperature is above

72F (22C) and at least once every month if the temperature goes above 85F (30C).

Troubleshooting

Symptom Cause Solution

Screen will not operate

and motor does not hum.

Incorrect line voltage. Verify 115125V (or 220240V). If insuicient voltage, rewire

incoming electric line.

Blown fuse. Replace fuse.

Tripped circuit breaker. Reset circuit breaker.

No power to operating switch

or junction.

Check above. Tighten all loose wire connections.

Correct any improper connections.

Down Position

Check for power across black and white leads.

Up Position

Check for power across red and white leads.

Screen will not operate

and motor does not hum.

Power at junction box.

Thermal overload tripped. Let motor cool down for 15 minutes. Try again.

Broken wire in the “down” or “up” position. Check for continuity. Cut o old splice and reconnect.

Defective motor, limit switch or capacitor. Replace motor assembly. NOTE: Motor is a sealed assembly.

Capacitor burned out. Replace motor assembly.

Screen does not stop

at correct position. Limit switch out of adjustment. See Screen Adjustment section.

Noise.

NOTE: Screen will operate

with a low pitched hum.

Squeaking, rubber end plug rubbing on motor. Center roller in case.

Grinding. Foreign object in screen

rubbing on roller or fabric. Remove.

Gear noise. Replace motor assembly.

Coasting. Defective brake. Replace motor assembly.

Fabric hangs crooked.

Screen not installed properly. Check for level and plumb.

Fabric has backed up inside case. Adjust “down” limit switch slowly until roller is exposed and

wrinkle comes out, then readjust for proper drop.

Fabric is damaged. Replace fabric.

84215

LIMITED FIVE YEAR WARRANTY ON DALITE PRESENTATION PRODUCTS

Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in

materials and workmanship for a period of ive (5) years from the date of purchase by the original purchaser; provided they are properly

operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the

factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered

with or repaired by a person other than authorized Da-Lite personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise.

Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,

transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.

To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use,

or merchantability, that may be mandated by statute or rule of law are limited to the ive (5) year warranty period. This warranty gives

you speciic legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED

BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION

OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Customer Care Specialists at

3100 North Detroit Street, Warsaw, IN 46582, (574) 2678101, (800) 6223737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DALITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS

WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DALITE WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

FOR YOUR IMAGE | legrandav.com

USA P 866.977.3901 E info@da-lite.com

CANADA P 877.345.4329 E canadainfo@milestone.com

EMEA P +31 495 580 840 E emea.sales@milestone.com

APAC P +852 2145 4099 E asia.da-lite@milestone.com

In British Columbia, Milestone AV Technologies ULC carries on business as MAVT Milestone AV Technologies ULC.

Technologies. All other brand names or marks are used for identiication purposes and are trademarks of

their respective owners. All patents are protected under existing designations. Other patents pending.