Da-Lite 34683V User Manual

Displayed below is the user manual for 34683V by Da-Lite which is a product in the Projection Screens category. This manual has pages.

INSTRUCTION BOOK FOR

Da-Snap Screen

2

1. Unpack the frame parts from the carton. DO NOT unroll the

screen surface at this time.

2. Slide the frame pieces together at corners. (NOTE: Frame

assembly holes may not appear to it properly at the corners

until all fasteners have been attached. Once fasteners are

attached, the frame corners will be drawn in for a proper it.)

Secure frame pieces with #10 screws provided. Do not tighten

screws until all are started, then tighten. See Figure 1.

NOTE: The frame pieces are labeled “top” and “bottom”. Be

sure the frame pieces are assembled according to the labels.

This will ensure the snap pattern on the frame and screen

surface will match.

Figure 1. Rear View

Snap Stud

Side

#10 Black Screw

Side

Top

Bottom

Snap Stud

Frame Bracket

Quantities vary by screen size

Screens 80" and smaller viewing width = 3

Screens over 80" to 96" viewing width = 4

Screens over 96" viewing width = 6

Quantity Included ________________________________________________

Frame Assembly

Included Hardware

Large Wall Bracket (47" Long)

Installation screws not included

Quantities vary by screen size:

Screens 80" and smaller viewing width = 1

Screens over 80" to 96" viewing width = 2

Screens over 96" viewing width = 3

Quantity Included ___________________________

Small Wall Bracket (8" Long)

Installation screws not included

Quantity = 1. Only for screens 80" and smaller viewing width.

Quantity Included ___________________________

High Power® Frame Bracket

Screens with High Power® quantity = 2

Screens with 2-piece side frame rails quantity = 2

Quantity Included ___________________________

Snap Stud

Quantity Included ___________________________

#10 Screw

Quantity Included ___________________________

Use Installation Method Number ____________

3

There are four methods of installation based on the size of the

screen and type of viewing surface. Measure the width of the

viewing area of your screen and refer to the appropriate method

of installation below. The wall bracket diagram shows the type

and quantity of bracket that is supplied based on the size of

the screen.

Method 1: Screens 80" and smaller in viewing width.

Method 2: Screens over 80" up to 96" in viewing width.

Method 3: Screens over 96" in viewing width.

Method 4: Any size screen with High Power® viewing surface.

Installation

Method 1 (Screens 80" And

Smaller In Viewing Width)

Method 1 (Screens 80" And

Smaller In Viewing Width)

4. Attach the small wall bracket to the wall. Refer to Figure 4

for proper orientation. Do not tighten the screws completely.

The bracket should slide up and down easily.

5. Unroll the screen on a clean surface. Do not use newspaper.

The viewing side is rolled to the inside of the roll. Place the

frame over the screen surface, and while lifting the frame with

one hand, snap the screen surface onto the frame with the

other hand while maintaining a steady pull on the surface.

6. Hang the screen on the brackets by hooking the bottom of the

frame onto the small wall bracket and lift up until you can hook

the top of the frame on the top bracket. Push down on the

frame to seat it on the brackets. Refer to Figure 4.

6"

2

Lift

3

1

Wall

Figure 3

Figure 4

1. Use the supplied #10 screws to attach three frame brackets to

the back of the frame as shown in Figure 2.

2. Secure the large wall bracket to wall studs at the desired height.

Make sure the bracket is level. The top of the frame will be 1/8"

above the top of the wall bracket when mounted. You will need at

least 5/8" clearance above the bracket to hang the screen.

3. To install the small wall bracket, you must measure the overall

height of the screen frame and subtract 13/8". Using that

dimension, measure down from the top edge of the large wall

bracket and mark the wall for two screw holes. The holes should

be centered within the frame and 6" apart. Refer to Figure 3.

Frame Brackets

3Pieces

#10 Screws

6Pieces

Large Wall

Bracket

1Piece

Small Wall Bracket

1Piece

Figure 2

Overall

Height Overall Height - 1 ⅜"

4

Method 2 (Screens Over 80" Up To 96" In Viewing Width)

1. Use the supplied #10 screws to attach four frame brackets to the

back of the frame as shown in Figure 5.

2. Secure the wall bracket to wall studs at the desired height. Make

sure the bracket is level. The top of the frame will be 1/8" above

the top of the wall bracket when mounted. You will need at least

5/8" clearance above the bracket to hang the screen.

3. To install the lower wall bracket, you must measure the overall

height of the screen frame and subtract 1/4". This is the

dimension from the top of the upper wall bracket to the

bottom of the lower wall bracket. See Figure 6.

4. Unroll the screen on a clean surface. Do not use newspaper. The

viewing side is rolled to the inside of the roll. Place the frame over

the screen surface, and while lifting the frame with one hand,

snap the screen surface onto the frame with the other hand

while maintaining a steady pull on the surface.

5. Position the screen with the attached surface onto the top wall

bracket as shown in Figure 7. Push down at the center of the

bottom frame rail to hook onto the lower wall bracket.

Figure 5

Frame Brackets

4Pieces

#10 Screws

8Pieces

Large Wall

Bracket

2Pieces

Figure 6

Wall

2

1

Wall

Figure 7

Overall Height - ¼"

Overall Height

5

Method 3 (Screens Over 96"

In Viewing Width) Method 4 (High Power® Fabric)

Cleaning

1. Use the supplied #10 screws to attach six frame brackets to the

back of the frame as shown in Figure 8.

2. Secure the wall brackets to wall studs at the desired height. Make

sure the brackets are level. The top of the frame will be 1/8" above

the top of the wall bracket when mounted. You will need at least

5/8" clearance above the bracket to hang the screen.

3. To install the lower wall bracket, you must measure the overall

height of the screen frame and subtract 1/4". This is the

dimension from the top of the upper wall bracket to the bottom

of the lower wall bracket. See Figure 6.

4. For 150", 180", 200", 220" and larger screens with 2-piece side

frame rails you will need to attach one High Power® bracket to

each side frame rail. Use the black #10 screws supplied.

See Figure 8.

5. Unroll the screen on a clean surface. Do not use newspaper. The

viewing side is rolled to the inside of the roll. Place the frame over

the screen surface, and while lifting the frame with one hand,

snap the screen surface onto the frame with the other hand

while maintaining a steady pull on the surface.

6. Position the screen with the attached surface onto the top wall

bracket as shown in Figure 7. Push down at the center of the

bottom frame rail to hook onto the lower wall bracket.

7. If you attached brackets to the side frame rails in step 4,

anchor these to the wall with an appropriate fastener for

your type of wall.

1. Use the supplied #10 screws to attach two frame brackets and

two High Power® brackets to the back of the frame as shown in

Figure 9.

2. Secure the large wall bracket to wall studs at the desired height.

Make sure the bracket is level. The top of the frame will be 1/8"

above the top of the wall bracket when mounted. You will need

at least 5/8" clearance above the bracket to hang the screen.

3. Unroll the screen on a clean surface. Do not use newspaper.

The viewing side is rolled to the inside of the roll. Place the frame

over the screen surface, and while lifting the frame with one

hand, snap the screen surface onto the frame with the other

hand while maintaining a steady pull on the surface.

4. Position the screen with the attached surface onto the top wall

bracket as shown in Figure 7. Push down at the center of the

bottom frame rail to tension the fabric. Mark the screw holes

for the bottom brackets. Drill holes in wall and attach the

brackets to the wall with screws.

Da-Tex®, Dual Vision, Pearlescent, Cinema Vision, High

Power®, Da-Mat®, High Contrast Da-Mat®, Audio Vision, High

Contrast Audio Vision, High Contrast Cinema Vision and High

Contrast Cinema Perf surfaces can be cleaned as follows:

Using a white clean cloth (100% cotton preferred) that is

dampened with clear water, gently wipe the area in one direction.

Do not use a circular motion. Using a dry 100% cotton cloth,

wipe dry after each cleaning session. To clean a stubborn stain

or a sticky surface, use denatured alcohol (methanol or methyl

alcohol) following the same procedure as for water.

Figure 9

Frame Brackets

2Pieces

#10 Screws

8Pieces

Large Wall

Bracket

1Piece

High Power

®

Bracket

2Pieces

Figure 8

Frame Brackets

6Pieces

#10 Screws

12Pieces

Large Wall

Brackets

3Pieces

High

Power

®

Bracket For

Large Split

Frames,

And 150",

180", 200"

And 220"

Diagonal

Screens.

2Pieces

6

7

LIMITED ONE YEAR WARRANTY ON DALITE PRESENTATION PRODUCTS

Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in

materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly

operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the

factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered

with or repaired by a person other than authorized Da-Lite personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise.

Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,

transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.

To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use,

or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives

you speciic legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED

BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION

OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137,

Warsaw, IN 465810137, (574) 2678101, (800) 6223737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DALITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS

WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DALITE WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

75135

A Milestone AV Technologies Brand

3100 North Detroit Street

Warsaw, Indiana 46582

P: 574.267.8101 or 800.622.3737

F: 574.267.7804 or 877.325.4832

E: info@da-lite.com

www.da-lite.com

DL–0262 01.14

© 2013 Milestone AV Technologies LLC. Printed in U.S.A.