Da-Lite 70082M User Manual
Displayed below is the user manual for 70082M by Da-Lite which is a product in the Projection Screens category. This manual has pages.
INSTRUCTION BOOK FOR
Tensioned Advantage®
Deluxe Electrol®
2
1. The case provides multiple attachment points for bolts,
cables, or threaded rod. Page 7 shows threaded rod installed.
The variable position-mounting bracket may be located
anywhere along the length of the case. It is recommended to
keep the brackets spaced evenly enough to distribute the
weight of the screen.
The case has a self-trimming lange around the bottom.
Ceiling tiles or drywall may be placed on top of this lange to
provide a inished appearance.
2. After securing the case in the ceiling check that the case is
level and plumb.
3. Use supplied 1/8" hex key and a 1/4" wrench to remove silver
shipping brackets attached to slat and screen case.
4. Install electrical connections that apply to your unit. Refer to
the following diagrams for proper installation. The diagrams
on page 4 are for standard controls; the diagrams on page 5
are for SCB100 controls and page 6 for SCB200 controls. The
terminal block for the wall switch connections is located
under the metal housing surrounding the junction box.
Remove two screws for access.
Case Installation
Important Safety Instructions
When using your video equipment, basic safety precautions
should always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or
contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rating
at least equal to that of the appliance should be used. Cords
rated for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric
shock when the appliance is used subsequently.
5. The use of an accessory attachment not recommended by
the manufacturer may cause a risk of ire, electric shock, or
injury to persons.
Save These Instructions
Pre-Installation
1. Carefully unpack screen and remove outer wrapping
from case.
2. Make sure to recheck measurements of screen location
before installation.
Figure 1
Fabric Door Access
Door
Screw For
Securing Roller
Access Door
3
Screen And Roller Assembly Installation
Screen Adjustment
If your screen was shipped with the motor and roller already installed proceed to step 6.
1. Remove the screw from each end of the access door (front
door) and open the door. See igure 1.
2. Carefully unpack screen and roller assembly. Leave packing
paper on the roller.
3. Place the roller assembly into the case with the motor on the
left side. The limit switches should be facing down. Line up
the square pin on the motor with the square hole in the
bracket.
4. Lift the pin end (right end) of the roller into position and slide
the bracket onto the roller pin. Tighten two nuts to secure the
bracket.
5. Complete electrical hook-up by snapping motor wire
connector into case connector.
6. Remove shipping brackets by removing the hex head screws
from aluminum slat and case. Slat should move freely. See
igure 2. (Only if the roller assembly is preinstalled.)
7. Test installation by operating the screen several times. Be
prepared to stop the screen. Standard Duty Cycle: 1 MIN. ON/3
MIN. OFF. The fabric door (rear door) will not close until the
wall switch is placed in the up position and when the screen
motor stops at its limit switch in the up direction.
CAUTION: Excessive continuous operation may cause the
motor to overheat. If this happens the motor will shut of
until it cools to a normal operating temperature.
ATTENTION! Le fonctionnement continu et excessif peut
provoquer une surchaufe.Si cela se produit, les moteurs
s'arrêteront jusqu'à qu'ils se soient refroidis à la
température normale de fonctionnement.
8. Run the screen down enough to open the fabric door. Close
the access door and reinstall the screws to secure the door.
CAUTION: Contact Da-Lite at 8006223737 or 5742678101 if screen or door motor needs adjustment.
ATTENTION: Contactez Da-Lite au 8006223737 ou au 5742678101 au cas le moteur de l'écran a besoin d'être ajusté.
Figure 2 Figure 3
Fabric
Door
Knockouts For
Conduit Installation
SCB100/SCB200
Access Cover
Access Door
Screen Motor
White
Adjustment
Knob "Down"
Door
Microswitch
Door Motor
Hex Head Screws Shipping
Bracket
Black
Adjustment
Knob "Up"
4
Tensioned Advantage® Deluxe Electrol® Instructions For Standard Control
220/240V Wiring Diagram
120V Wiring Diagram
Screen Motor
Screen Motor
Black (Up)
Red (Up)
Red (Up)
Black (Down)
Black (Down)
WHITE (Common)
WHITE (Common)
Optional RF or IR
Remote Connector
Optional RF or IR
Remote Connector
White (Common)
Blue (Common)
Black (Hot)
Brown (Hot)
Green (Ground)
Green/Yellow (Ground)
Power Input
120VAC/60HZ
Power Input
240VAC/50HZ
Door Motor
Door Motor
DOWN
STOP
UP
NOTE: Electrical connections
on left end of case.
Not Used
Not Used
AUX EYE
AUX EYE
Not Used
Not Used
WHITE (Common)
NOTE: 2024AWG Wire Recommended
For Connecting Wall Switch to the Dual
Motor Controller
NOTE: 2024AWG Wire Recommended
For Connecting Wall Switch to the Dual
Motor Controller
Door Microswitch
Door Microswitch
Front of
Wall
Switch
Front of
Wall
Switch
Back of
Wall
Switch
Back of
Wall
Switch
Black (Down)
WHITE (Common)
Red (Up)
Red (Down)
WHITE (Common)
Red (Up)
Black (Down)
Green (Ground)
WHITE (Common)
Red (Up)
Black (Down)
Green (Ground)
WHITE (Common)
Red (Down)
Black (Up)
Green (Ground)
WHITE (Common)
Red (Down)
Black (Up)
Green (Ground)
NOTE: Electrical connections
on left end of case.
DOWN
STOP
UP
WHITE (Common)
Red (Up)
Black (Down)
Brown (Up)
Brown (Down)
Blue (Common)
Black (Up)
Black (Down)
Blue (Common)
Blue (Common)
Blue (Common)
Black (Up)
Black (Down)
Brown (Down)
Brown (Up)
Green/Yellow (Ground)
Green/Yellow (Ground)
Blue (Common)
Blue (Common)
Black (Up)
Black (Down)
Brown (Down)
Brown (Up)
Green/Yellow (Ground)
Green/Yellow (Ground)
Not Used
Not Used
Red (Up)
Black (Down)
WHITE (Common)
5
Not Used
Not Used
Tensioned Advantage® Deluxe Electrol® Instructions SCB100 Control
Power Input and Control
Board are Located on Right
Side of Screen Housing.
Brown (Hot)
Green/Yellow (Ground)
Blue (Common)
Power Input
240VAC/50HZ
DOWN
STOP
UP
Back Of Front Of
Wall Switch Wall Switch
Screen Motor
Door Motor
Terminal Block
TX - Data Out
G - Ground
RX - Data In
TX - Data Out
G - Ground
RX - Data In
White (Common)
Black (Down)
Red (Up)
- 12VDC Out
+ 12VDC Out
Screen and Door Motor, Microswitch
and Timer Relay Are Located on Left
Side of Screen Housing.
Door Microswitch
Blue
(Common)
Brown (Up)
Brown (Down)
Blue (Common)
Black (Up)
Gray (Door)
Brown (Down)
Green/Yellow (Ground)
Blue (Common)
Black (Down)
Brown (Down)
Green/Yellow (Ground)
Blue (Common)
Black (Up)
Gray (Door)
Brown (Down)
Green/Yellow (Ground)
Brown/
Yellow
Black (Down)
Blue (Common)
Blue (Common)
Brown (Down)
Black (Up)
Brown (Hot)
Green/Yellow (Ground)
Blue (Common)
NOTE: 2024AWG Wire
Recommended for Connecting Wall
Switch to the Dual Motor Controller
Power Input and Control
Board are Located on Right
Side of Screen Housing.
220/240V Wiring Diagram
120V Wiring Diagram
NOTE: Electrical connections on right side of case.
NOTE: Electrical connections on right side of case.
Black (Hot)
Green (Ground)
White (Common)
Power Input
120VAC/60HZ
DOWN
STOP
UP
Back Of Front Of
Wall Switch Wall Switch
Screen Motor
Door Motor
TX - Data Out
G - Ground
RX - Data In
TX - Data Out
G - Ground
RX - Data In
White (Common)
Black (Down)
Red (Up)
- 12VDC Out
+ 12VDC Out
Screen and Door Motor, Microswitch
and Timer Relay Are Located on Left
Side of Screen Housing.
Door Microswitch
White
(Common)
Black (Up)
White (Common)
Red (Down)
Black (Up)
Green (Ground)
Black (Down)
White (Common)
Red (Up)
Gray (Door)
Black (Down)
Green (Ground)
White (Common)
Red (Up)
Gray (Door)
Black (Down)
Green (Ground)
Black/
Yellow
Red (Down)
White (Common)
White (Common)
Black (Down)
Black (Hot)
Green (Ground)
White (Common)
NOTE: 2024AWG Wire
Recommended For Connecting Wall
Switch to the Dual Motor Controller
Red (Up)
Terminal Block
6
Not Used
Not Used
Tensioned Advantage® Deluxe Electrol® Instructions SCB200 Control
Blue (Common)
Black (Down)
Brown (Down)
Green/Yellow (Ground)
Power Input and Control
Board are Located on Right
Side of Screen Housing.
Brown (Hot)
Green/Yellow (Ground)
Blue (Common)
Power Input
240VAC/50HZ
Encoder
5V A B GND
Screen Motor
Door Motor
Screen and Door Motor, Microswitch
and Timer Relay Are Located on Left
Side of Screen Housing.
Door Microswitch
Blue
(Common)
Brown (Up)
Brown (Down)
Blue (Common)
Black (Up)
Gray (Door)
Brown (Down)
Green/Yellow (Ground)
Blue (Common)
Black (Up)
Gray (Door)
Brown (Down)
Green/Yellow (Ground)
Black (Down)
Blue (Common)
Blue (Common)
Brown (Down)
Black (Up)
Brown (Hot)
Green/Yellow (Ground)
Blue (Common)
Black (Up)
Brown (Down)
Blue (Common)
B + A -
Power Input and Control
Board are Located on Right
Side of Screen Housing.
220/240V Wiring Diagram
120V Wiring Diagram
NOTE: Electrical connections on right side of case.
NOTE: Electrical connections on right side of case.
Black (Hot)
Green (Ground)
White (Common)
Power Input
120VAC/60HZ
Encoder
5V A B GND
Screen Motor
Door Motor
Screen and Door Motor, Microswitch
and Timer Relay Are Located on Left
Side of Screen Housing.
Door Microswitch
White
(Common)
Black (Up)
White (Common)
Red (Up)
Black (Down)
Green (Ground)
Black (Down)
White (Common)
Red (Up)
Gray (Door)
Black (Down)
Green (Ground)
White (Common)
Red (Up)
Gray (Door)
Black (Down)
Green (Ground)
Black/
Yellow
Brown/
Yellow
Red (Down)
White (Common)
White (Common)
Black (Down)
Red (Up)
Black (Hot)
Green (Ground)
White (Common)
Red (Up)
Black (Hot)
White (Common)
B + A -
7
Tensioned Advantage® Deluxe Electrol® Installation
See Detail A
(Suggested) ⅜"
Threaded Rod (Not
Included)
4.59"
Detail A
Hanger Bracket
Flat Bracket Mounting Method
Formed Bracket
Mounting Method
(Suggested) ⅜"
Threaded Rod
(Not Included)
Attached to
Mounting
Bracket
9 ¼"
Finished
Ceiling
Self-Trimming
Flange
8 ¾"
7 ¼"
8.75"
7.21" 8.74"
Motor End
Variable Position
Mounting Brackets
7 ¼"
7 ⅝"
Electrical
Junction Box
7 ¼"
7 ⅝"
Case Length
8
Troubleshooting
Visit www.da-lite.com to ind installation and troubleshooting
tutorials. You will also ind a link to Live Chat for interactive
support and you can contact us by email at info@da-lite.com or
by phone at (800) 6223737 or (574) 2678101 with any
troubleshooting questions.
Symptom Cause Solution
If screen is not responding
properly and SCB100 or
SCB200 controls are used,
contact the factory for
troubleshooting assistance.
Screen will not operate or will
not go “down”.
Motor does not hum.
Motor hums.
Incorrect line voltage. Verify 115125V (or 220240V). If insuicient voltage,
rewire incoming electric line.
Blown facility fuse. Replace facility fuse.
Tripped facility circuit breaker. Reset facility circuit breaker.
No power to operating switch
or junction box.
Check above. Tighten all loose wire connections.
Recheck wiring. See installation instructions.
"Down" Position
Check for power across black and white leads.
Power at junction box.
Thermal overload tripped. Let motor cool down for 15 minutes. Try again.
Broken wire in the “down” position. Check for continuity.
Defective motor, limit switch or capacitor. Replace motor assembly. NOTE: Motor is a sealed assembly.
Capacitor burned out. Replace motor assembly.
Screen will not move upward.
Motor does not hum.
Motor hums.
Incorrect line voltage. Verify 115125V (or 220240V). If insuicient voltage,
rewire incoming electric line.
Blown facility fuse. Replace facility fuse.
Tripped facility circuit breaker. Reset facility circuit breaker.
No power to operating switch or junction box.
Check above. Tighten all loose wire connections. See above
"Up" Position
Check for power across red and white leads.
.
Open door limit switch. Replace switch.
Power at junction box. Thermal overload tripped. Let motor cool down for 15 minutes. Try again.
Broken wire in the “up” position. Check for continuity.
Defective motor, limit switch or capacitor. Replace motor assembly. NOTE: Motor is a sealed assembly.
Capacitor burned out. Replace motor assembly.
9
Symptom Cause Solution
Door will not open.
Hinge is bound or has a foreign substance on it
which does not allow it to open by gravity.
Check installation to free door. Clear any foreign
substance; i.e., paint or plaster from hinge.
No power. See above.
Door does not close.
Open door limit switch. Replace switch.
No power from screen motor. Replace screen motor
“Down” limit switch incorrect.. “Down” limit switch out of adjustment. See installation instructions.
Noise.
NOTE: Screen will operate with
a low-pitched hum.
Buzzing noise. Adjust door limit switch (too far down).
Gear noise Replace motor assembly.
Coasting. Defective brake. Replace motor assembly.
Roller displaced from mounting
bracket. Pin end slipped out of nylon bearing Realign pin end bracket.
Fabric hangs crooked.
Screen not installed properly. Check for level and plumb.
Fabric is damaged. Replace fabric.
Door closes before screen is all
the way up. Screen “up” limit out of adjustment. Adjust “up” limit (call factory for instructions).
Door opens but screen does not
operate. Loose wire. Check all wiring and connections..
LIMITED ONE YEAR WARRANTY ON DALITE PRESENTATION PRODUCTS
Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in
materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly
operated according to Da-Lite’s instructions and are not damaged due to improper handling or treatment after shipment from the
factory.
This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered
with or repaired by a person other than authorized Da-Lite personnel.
Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise.
Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,
transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.
To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use,
or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives
you speciic legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED
BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION
OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.
In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137,
Warsaw, IN 465810137, (574) 2678101, (800) 6223737.
IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DALITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS
WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DALITE WRITTEN INSTRUCTIONS.
Keep your sales receipt to prove the date of purchase and your original ownership.
88585
A Milestone AV Technologies Brand
3100 North Detroit Street
Warsaw, Indiana 46582
P: 574.267.8101 or 800.622.3737
F: 574.267.7804 or 877.325.4832
E: info@da-lite.com
www.da-lite.com
DL–0176 (Rev. 3) 10.14
© 2014 Milestone AV Technologies LLC. Printed in U.S.A.