Da-Lite 70217L User Manual
Displayed below is the user manual for 70217L by Da-Lite which is a product in the Projection Screens category. This manual has pages.
INSTRUCTION BOOK FOR
Tensioned Cosmopolitan Electrol
For Sizes Up To 10' x 10'
2
1. Carefully unpack screen and remove outer wrapping
from case.
2. Remove shipping brackets by removing the screws from
the slat bar and wooden board and use supplied 1/8" next
key to remove silver shipping brackets attached to slat.
3. Always handle screen in horizontal position.
There are three methods of mounting to include:
Flush against wall; Suspended from ceiling (use extension brackets); and recessed above ceiling.
Important Safety Instructions
When using your video equipment, basic safety precautions
should always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or
contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rating
at least equal to that of the appliance should be used. Cords
rated for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric
shock when the appliance is used subsequently.
5. The use of an accessory attachment not recommended by
the manufacturer may cause a risk of ire, electric shock, or
injury to persons.
Save These Instructions
Pre-Installation
Installation
NOTE: Under no circumstances should unit be completely sealed in recessed installation. Allow access for service. Picture surface is centered
in case. Case extends 51/2" beyond surface on either end. Do not attach anything to screen slat rod or bottom fabric pocket.
1. Make sure screen is level. Use a carpenter‘s level and plumb level.
CAUTION! Do not cut wrapping paper or tape with knife or any
sharp tool. Remove by hand.
ATTENTION! Ne coupez pas le papier d'emballage ou le ruban
adhésif avec un couteau ou un outil tranchant. Retirez à la
main.
2. Install electrical hook-up that applies to your unit. Make sure to
review your Electrical Installation Checklists and Wiring Diagrams
(included) for either 120 Volt Switch, 220/240 Volt Switch, or Low
Voltage Control.
3. Test installation by running screen up and down a few times. Be
prepared to stop screen. Standard Duty Cycle:
1 MIN. ON / 3 MIN. OFF.
NOTE: Must be installed in accordance with the requirements of
the Local Building Codes, the Canadian Electrical Code (CEC),
CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70.
Picture
Surface
Picture
Surface
Picture
Surface Picture
Surface
Ceiling
Mounted
Wall Mounted Concealed (Allow Room For Access)
Use No. 6
Brackets To
Hang Behind
Beam or
Valance
3
Tensioned Cosmopolitan® Electrol® Installation
120V Wiring Diagram
Wiring Enclosure Cover
Down
White Limit
Switch
Adjustment
In Multiple Control
Installations This
Switch Is Replaced By
The Low Voltage
Control, Operated
From Push Button
Stations.
Operating Switch
And Plate Furnished
With Screen (SPDT
With Center Of)
Side View
Of Switch
And Box
This Switch Cannot Be Used With LVC.
NOTE: A single switch cannot be used to operate more
than one screen. Contact the factory for further
information.
Down Black
Black
Up White
Red
Down
AC Hot
Of
Common
White
Black With
Yellow
Up Red
Rocker
Switch
AC Common
120 V. 60 Hz. 2.5 Max. Amp
To Junction Box, Mounted In Screen Case,
In Which Internal Wiring Terminates In
White, Black and Red Leads
Motor
End
¾" Diameter
Hole For Wall
Installation
Overall Length of Case
Between Hanger Eyes
Overall Length of Slat
Slat
Picture
Surface
Enclosure Cover
⅜" Diameter For
Ceiling Mounting
⅞" Diameter Opening
For Electrical Settings
1 ⅞"
⁄"
5 ⅞"
4 ⅝"
240 VOLT WIRING DIAGRAM FOR STANDARD WALL SWITCH:
Da-Lite ofers two styles of 240 volt wall switches for standard
operation. Please see wiring diagram included in wall switch box
included with screen.
4
120V Wiring Diagram with Optional Built-In Low Voltage Control
Up
Down
Common
Bus
5V
Ground–Must Be Connected
To Building Ground
UP
STOP
DOWN
Power Input 120VAC / 60Hz
Green (Ground)
Black (Hot)
White (Common)
Power Wire
Data Cable
RJ45 Jack
RJ45 Receptacle
RJ22 Output
RJ22
Jack
RJ22
Inputs
RJ22
Jack
LED
Up Limit
Tactile
Button
Down
Limit
Tactile
Button
Front Of
Wall Switch
Back Of
Wall Switch
Dry Contacts
BUS
BUS
COM
5V
BUS
3-conductor 2024 gauge wire can be used in place of the
supplied RJ14 cable to connect the wall switch. Connect the BUS
terminals on the wall switch to the corresponding BUS terminals
on the splitter board.
IMPORTANT NOTE: The wall switch is REQUIRED to make any
limit switch adjustments, EVEN if a third party control system is
used. Therefore, it is advised to wire the switch or provide a
3-conductor connection that is accessible.
RJ14 Pin-Outs (Tab Is Facing Up)
Supplied RJ14 cable
Bus (RP Data)
RQ Data
+5V
Ground
White
Green
Red
Black
RJ22 Pin-Outs (Tab Is Facing Up)
Standard RJ22 can be used in place of RJ14
Bus (RP Data)
+12V
RQ Clock
RQ Data
+5V
Ground
Yellow
Green
Red
Black
White
Blue
RJ45 Pin-Outs (Tab Is Facing Up)
+12V
Manual 2
Ground
Manual 1
RQ Clock
Bus (RP Data)
RQ Data
+5V
Blue
Green
Yellow
Red
Black
Orange
Purple
Brown
5
CAUTION: The projector must be turned of before
connecting the trigger wires to the projector. Failure to do
so may damage the controller.
ATTENTION: Le projecteur doit être éteint avant de brancher
les ils de déclenchement à celui-ci. Tout manquement à
cette instruction pourrait endommager le contrôleur.
Use 2-conductor 2024 gauge wire to extend the low voltage
connection from the projector’s 5 or 12-volt screen trigger output
to the length required to reach the VPI. When extending the low
voltage connection from the projector’s screen trigger output
polarity does not matter. The red and black wires from the VPI
are interchangeable.
120V Wiring Diagram with Optional Built-In Video Projector Interface
⁄ Volt Screen
Trigger On Projector
Ground–Must Be Connected
To Building Ground
UP
STOP
DOWN
Power Input 120VAC / 60Hz
Green (Ground)
Black (Hot)
White (Common)
Power
Wire
Data Cable
RJ45 Jack
RJ45 Receptacle
RJ22 Output
RJ22 Jack
RJ22
Inputs
RJ22
Jack
LED
Up
Limit
Tactile
Button
Down
Limit
Tactile
Button
Front Of
Wall Switch
Back Of
Wall Switch
Black
Red
VPI Trigger Module
Dry Contacts
Up
Down
Common
Bus
5V
BUS
BUS
COM
5V
BUS
IMPORTANT NOTE: The wall switch is REQUIRED to make any
limit switch adjustments, EVEN if a third party control system is
used. Therefore, it is advised to wire the switch or provide a
3-conductor connection that is accessible.
3-conductor 2024 gauge wire can be used in place of the
supplied RJ14 cable to connect the wall switch. Connect the
BUS terminals on the wall switch to the corresponding BUS
terminals on the splitter board.
6
Tensioned Cosmopolitan® Electrol® Installation
Screen Adjustment
The screen surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly
adjusted at Da-Lite. The screen should not be adjusted for more or less drop. The fabric cables are adjusted for proper vertical
and lateral tension at Da-Lite.
CAUTION! Contact Da-Lite at 8006223737 or 5742678101 if screen motor needs adjustment.
ATTENTION! Contactez Da-Lite au 8006223737 ou au 5742678101 au cas le moteur de l'écran a besoin d'être ajusté.
Low-Voltage Wall Switch
Optional IR and RF
Remote Control
Splitter
Motor
Ground to Case
240VAC 50Hz
240V Wiring Diagram
With Optional Built-In
Low Voltage Control
Up
Stop
Down
Ground–Must be
Connected to
Building Ground
Green
Front Back
UP DN GND +5V
3Position
Switch RJ9
UP
+5V
COM
DN
IMPORTANT NOTE: The wall switch is REQUIRED to make
any limit switch adjustments, EVEN if a third party control
system is used. Therefore, it is advised to wire the switch or
provide a 4-conductor connection that is accessible.
Connect Supplied RJ9 Cable
to Splitter and Switch, or use
4 Cable Conductor to Connect
to Screw Terminals.
ILT RJ9 Pin-Outs (Tab Is Facing Up)
Ground Common
IR or Up
+5V
DN or Data
Red
Green
White
Black
Green
Brown (Hot)
Blue (Common)
RJ9
RJ9
Dry Contacts
7
Troubleshooting
Symptom Cause Solution
Screen will not operate.
Motor does not hum.
Motor hums.
Incorrect line voltage. Verify 115125V (or 220240V). If insuicient voltage, rewire
incoming electric line.
Blown fuse. Replace fuse.
Tripped circuit breaker. Reset circuit breaker.
No power to operating switch or junction.
Check above. Tighten all loose wire connections.
Correct any improper connections.
“Down” Position
Check for power across black and white leads.
“Up” Position
Check for power across red and white leads.
Power at junction box.
Thermal overload tripped.
Let motor cool down for 15 minutes. Try again.
Broken wire in the “up” or ”down” position. Check for continuity. Cut o old splice and reconnect.
Defective motor, limit switch or capacitor. Replace motor assembly.
NOTE: Motor is a sealed assembly.
Temporary binding. With power “o”, turn roller by hand to free binding.
Capacitor burned out. Replace motor assembly.
Incorrect stopping position in
downward direction. “Down” limit switch out of adjustment. Contact Da-Lite at 8006223737 or 5742678101.
Incorrect stopping position in
upward direction. “Up” limit switch out of adjustment. Contact Da-Lite at 8006223737 or 5742678101.
Noise.
NOTE: Screen will operate
with a low pitched hum.
Gear noise. Replace motor assembly.
Coasting. Defective brake. Replace motor assembly.
Roller displaced from
mounting bracket. Pin end slipped out of nylon bearing. Realign pin end bracket.
Visit www.da-lite.com to ind installation and troubleshooting
tutorials. You will also ind a link to Live Chat for interactive
support and you can contact us by email at
info@da-lite.com or by phone at (800) 6223737 or (574) 2678101
with any troubleshooting questions.
LIMITED ONE YEAR WARRANTY ON DALITE PRESENTATION PRODUCTS
Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in
materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly
operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the
factory.
This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered
with or repaired by a person other than authorized Da-Lite personnel.
Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise.
Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,
transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.
To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use,
or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives
you speciic legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED
BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION
OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.
In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137,
Warsaw, IN 465810137, (574) 2678101, (800) 6223737.
IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DALITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS
WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DALITE WRITTEN INSTRUCTIONS.
Keep your sales receipt to prove the date of purchase and your original ownership.
76063
A Milestone AV Technologies Brand
3100 North Detroit Street
Warsaw, Indiana 46582
P: 574.267.8101 or 800.622.3737
F: 574.267.7804 or 877.325.4832
E: info@da-lite.com
www.da-lite.com
DL–0264 (Rev. 2) 10.14
© 2014 Milestone AV Technologies LLC. Printed in U.S.A.