Da-Lite 70373 User Manual
Displayed below is the user manual for 70373 by Da-Lite which is a product in the Projection Screens category. This manual has pages.
INSTRUCTION BOOK FOR
Da-Snap Screen
2
1. Unpack the frame parts from the carton. DO NOT unroll the
screen surface at this time.
2. Slide the frame pieces together at corners. (NOTE: Frame
assembly holes may not appear to it properly at the corners
until all fasteners have been attached. Once fasteners are
attached, the frame corners will be drawn in for a proper it.)
Secure frame pieces with #10 screws provided. Do not tighten
screws until all are started, then tighten. See Figure 1.
NOTE: The frame pieces are labeled “top” and “bottom”. Be
sure the frame pieces are assembled according to the labels.
This will ensure the snap pattern on the frame and screen
surface will match.
Figure 1. Rear View
Snap Stud
Side
#10 Black Screw
Side
Top
Bottom
Snap Stud
Frame Bracket
Quantities vary by screen size
Screens 80" and smaller viewing width = 3
Screens over 80" to 96" viewing width = 4
Screens over 96" viewing width = 6
Quantity Included ________________________________________________
Frame Assembly
Included Hardware
Large Wall Bracket (47" Long)
Installation screws not included
Quantities vary by screen size:
Screens 80" and smaller viewing width = 1
Screens over 80" to 96" viewing width = 2
Screens over 96" viewing width = 3
Quantity Included ___________________________
Small Wall Bracket (8" Long)
Installation screws not included
Quantity = 1. Only for screens 80" and smaller viewing width.
Quantity Included ___________________________
High Power® Frame Bracket
Screens with High Power® quantity = 2
Screens with 2-piece side frame rails quantity = 2
Quantity Included ___________________________
Snap Stud
Quantity Included ___________________________
#10 Screw
Quantity Included ___________________________
Use Installation Method Number ____________
3
There are four methods of installation based on the size of the
screen and type of viewing surface. Measure the width of the
viewing area of your screen and refer to the appropriate method
of installation below. The wall bracket diagram shows the type
and quantity of bracket that is supplied based on the size of
the screen.
Method 1: Screens 80" and smaller in viewing width.
Method 2: Screens over 80" up to 96" in viewing width.
Method 3: Screens over 96" in viewing width.
Method 4: Any size screen with High Power® viewing surface.
Installation
Method 1 (Screens 80" And
Smaller In Viewing Width)
Method 1 (Screens 80" And
Smaller In Viewing Width)
4. Attach the small wall bracket to the wall. Refer to Figure 4
for proper orientation. Do not tighten the screws completely.
The bracket should slide up and down easily.
5. Unroll the screen on a clean surface. Do not use newspaper.
The viewing side is rolled to the inside of the roll. Place the
frame over the screen surface, and while lifting the frame with
one hand, snap the screen surface onto the frame with the
other hand while maintaining a steady pull on the surface.
6. Hang the screen on the brackets by hooking the bottom of the
frame onto the small wall bracket and lift up until you can hook
the top of the frame on the top bracket. Push down on the
frame to seat it on the brackets. Refer to Figure 4.
6"
2
Lift
3
1
Wall
Figure 3
Figure 4
1. Use the supplied #10 screws to attach three frame brackets to
the back of the frame as shown in Figure 2.
2. Secure the large wall bracket to wall studs at the desired height.
Make sure the bracket is level. The top of the frame will be 1/8"
above the top of the wall bracket when mounted. You will need at
least 5/8" clearance above the bracket to hang the screen.
3. To install the small wall bracket, you must measure the overall
height of the screen frame and subtract 13/8". Using that
dimension, measure down from the top edge of the large wall
bracket and mark the wall for two screw holes. The holes should
be centered within the frame and 6" apart. Refer to Figure 3.
Frame Brackets
3Pieces
#10 Screws
6Pieces
Large Wall
Bracket
1Piece
Small Wall Bracket
1Piece
Figure 2
Overall
Height Overall Height - 1 ⅜"
4
Method 2 (Screens Over 80" Up To 96" In Viewing Width)
1. Use the supplied #10 screws to attach four frame brackets to the
back of the frame as shown in Figure 5.
2. Secure the wall bracket to wall studs at the desired height. Make
sure the bracket is level. The top of the frame will be 1/8" above
the top of the wall bracket when mounted. You will need at least
5/8" clearance above the bracket to hang the screen.
3. To install the lower wall bracket, you must measure the overall
height of the screen frame and subtract 1/4". This is the
dimension from the top of the upper wall bracket to the
bottom of the lower wall bracket. See Figure 6.
4. Unroll the screen on a clean surface. Do not use newspaper. The
viewing side is rolled to the inside of the roll. Place the frame over
the screen surface, and while lifting the frame with one hand,
snap the screen surface onto the frame with the other hand
while maintaining a steady pull on the surface.
5. Position the screen with the attached surface onto the top wall
bracket as shown in Figure 7. Push down at the center of the
bottom frame rail to hook onto the lower wall bracket.
Figure 5
Frame Brackets
4Pieces
#10 Screws
8Pieces
Large Wall
Bracket
2Pieces
Figure 6
Wall
2
1
Wall
Figure 7
Overall Height - ¼"
Overall Height
5
Method 3 (Screens Over 96"
In Viewing Width) Method 4 (High Power® Fabric)
Cleaning
1. Use the supplied #10 screws to attach six frame brackets to the
back of the frame as shown in Figure 8.
2. Secure the wall brackets to wall studs at the desired height. Make
sure the brackets are level. The top of the frame will be 1/8" above
the top of the wall bracket when mounted. You will need at least
5/8" clearance above the bracket to hang the screen.
3. To install the lower wall bracket, you must measure the overall
height of the screen frame and subtract 1/4". This is the
dimension from the top of the upper wall bracket to the bottom
of the lower wall bracket. See Figure 6.
4. For 150", 180", 200", 220" and larger screens with 2-piece side
frame rails you will need to attach one High Power® bracket to
each side frame rail. Use the black #10 screws supplied.
See Figure 8.
5. Unroll the screen on a clean surface. Do not use newspaper. The
viewing side is rolled to the inside of the roll. Place the frame over
the screen surface, and while lifting the frame with one hand,
snap the screen surface onto the frame with the other hand
while maintaining a steady pull on the surface.
6. Position the screen with the attached surface onto the top wall
bracket as shown in Figure 7. Push down at the center of the
bottom frame rail to hook onto the lower wall bracket.
7. If you attached brackets to the side frame rails in step 4,
anchor these to the wall with an appropriate fastener for
your type of wall.
1. Use the supplied #10 screws to attach two frame brackets and
two High Power® brackets to the back of the frame as shown in
Figure 9.
2. Secure the large wall bracket to wall studs at the desired height.
Make sure the bracket is level. The top of the frame will be 1/8"
above the top of the wall bracket when mounted. You will need
at least 5/8" clearance above the bracket to hang the screen.
3. Unroll the screen on a clean surface. Do not use newspaper.
The viewing side is rolled to the inside of the roll. Place the frame
over the screen surface, and while lifting the frame with one
hand, snap the screen surface onto the frame with the other
hand while maintaining a steady pull on the surface.
4. Position the screen with the attached surface onto the top wall
bracket as shown in Figure 7. Push down at the center of the
bottom frame rail to tension the fabric. Mark the screw holes
for the bottom brackets. Drill holes in wall and attach the
brackets to the wall with screws.
Da-Tex®, Dual Vision, Pearlescent, Cinema Vision, High
Power®, Da-Mat®, High Contrast Da-Mat®, Audio Vision, High
Contrast Audio Vision, High Contrast Cinema Vision and High
Contrast Cinema Perf surfaces can be cleaned as follows:
Using a white clean cloth (100% cotton preferred) that is
dampened with clear water, gently wipe the area in one direction.
Do not use a circular motion. Using a dry 100% cotton cloth,
wipe dry after each cleaning session. To clean a stubborn stain
or a sticky surface, use denatured alcohol (methanol or methyl
alcohol) following the same procedure as for water.
Figure 9
Frame Brackets
2Pieces
#10 Screws
8Pieces
Large Wall
Bracket
1Piece
High Power
®
Bracket
2Pieces
Figure 8
Frame Brackets
6Pieces
#10 Screws
12Pieces
Large Wall
Brackets
3Pieces
High
Power
®
Bracket For
Large Split
Frames,
And 150",
180", 200"
And 220"
Diagonal
Screens.
2Pieces
6
7
LIMITED ONE YEAR WARRANTY ON DALITE PRESENTATION PRODUCTS
Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in
materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly
operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the
factory.
This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered
with or repaired by a person other than authorized Da-Lite personnel.
Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise.
Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,
transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.
To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use,
or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives
you speciic legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED
BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION
OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.
In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137,
Warsaw, IN 465810137, (574) 2678101, (800) 6223737.
IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DALITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS
WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DALITE WRITTEN INSTRUCTIONS.
Keep your sales receipt to prove the date of purchase and your original ownership.
75135
A Milestone AV Technologies Brand
3100 North Detroit Street
Warsaw, Indiana 46582
P: 574.267.8101 or 800.622.3737
F: 574.267.7804 or 877.325.4832
E: info@da-lite.com
www.da-lite.com
DL–0262 01.14
© 2013 Milestone AV Technologies LLC. Printed in U.S.A.