Da-Lite 81187V User Manual

Displayed below is the user manual for 81187V by Da-Lite which is a product in the Projection Screens category. This manual has pages.

INSTRUCTION BOOK FOR

Imager

There are three methods of installation based on the size of the screen. Measure the width of the viewing area of your screen and refer

to the appropriate method of installation below. The hanger bracket igure shows the type and quantity of bracket that is supplied based

on the size of the screen.

Method 1: Screens 80" and smaller in viewing width.

Method 2: Screens over 80" up to 96" in viewing width.

Method 3: Screens over 96" in viewing width.

Installation

Included Hardware

Large Wall Bracket (47" Long)

Installation screws not included

Quantities vary by screen size:

Screens 80" and smaller viewing width = 1

Screens over 80" to 96" viewing width = 2

Screens over 96" viewing width = 3

Quantity Included ___________________________

Small Wall Bracket (8" Long)

Installation screws not included

Quantity = 1. Only for screens 80" and smaller viewing width.

Quantity Included ___________________________

Corner Bracket

Quantity = 4 (Attached to frame)

Quantity Included ___________________________ Snap Stud

Quantity Included ___________________________

#10 Screw

Quantity Included ___________________________

Use Installation Method Number ____________

Tools Required:

Phillips Screwdriver

Carpenter’s Level

Tape Measure

Frame Assembly

1. Place the four frame pieces on a clean loor.

2. Slide the frame pieces together at corners. (Note: Frame

assembly holes may not appear to it properly at the corners

until all fasteners have been attached. Once fasteners are

attached, the frame corners will be drawn in for a proper it.)

Secure frame pieces with #10 screws provided. Do not tighten

screws until all are started, then tighten. See Figure 1.

3. Tighten the two screws at each corner. Do not over-tighten

the screws.

4. Insert and tighten the snap stud in the center of the corner

bracket (Figure 1).

Attach The Viewing Surface

Unroll the screen on a clean surface. Do not use newspaper.

The viewing side is rolled to the inside of the roll. Place the frame

over the screen surface, and while lifting the frame with one

hand, snap the screen surface onto the frame with the other

hand while maintaining a steady pull on the surface.

Method 1

1. Secure the large wall bracket to wall studs at the desired height.

Make sure the bracket is level. The top of the frame will be 1/8"

above the top of the wall bracket when mounted. You will need at

least 5/8" clearance above the bracket to hang the screen.

Figures 2, 3, and 4 show the proper orientation for the supplied

wall brackets.

2. To install the small wall bracket, you must measure the overall

height of the screen frame and subtract 13/8". Using that

dimension, measure down from the top edge of the wall bracket

and mark the wall for two screw holes. The holes should be

centered within the frame and 6" apart. Refer to Figure 3.

3. Attach the small wall bracket to the wall. Refer to Figure 4 for

proper orientation. Do not tighten the screws completely. The

bracket should slide up and down easily.

4. Hang the screen on the brackets by hooking the bottom of the

frame onto the small wall bracket and lift up until you can hook

the top of the frame on the top large bracket. Push down on the

frame to seat it on the brackets. Refer to Figure 4.

Setting Up Your Screen

Method 1 (Screens 80" And Smaller In Viewing Width)

Figure 1

Figure 2

Small Wall Bracket

1Piece

Large Wall

Bracket

1Piece

Method 1 (Screens 80" And Smaller

In Viewing Width)

Method 2 (Screens Over 80" Up To 96"

In Viewing Width)

Method 2

1. Secure the large wall bracket to wall studs at the desired

height. Make sure the large bracket is level. The top of the

frame will be 1/8" above the top of the large wall bracket when

mounted. You will need at least 5/8" clearance above the

bracket to hang the screen. Figures 5 and 6 show the proper

orientation for the supplied wall brackets.

2. To install the lower wall bracket, you must measure the

overall height of the screen frame and subtract 1/4". This is

the dimension from the top of the upper wall bracket to the

bottom of the lower wall bracket. See Figure 6.

3. Position the screen with the attached surface onto the top

wall bracket as shown in Figure 6. Push down at the center of

the bottom frame rail to hook onto the lower wall bracket.

Figure 3

Large Wall Bracket

Figure 4

Lift

Wall

Overall

Height Overall Height – 1 ⅜"

Figure 5

Large Wall

Bracket

2Pieces

Figure 6

Wall

Overall

Height – ¼"

Overall

Height

1. Secure the large wall brackets to wall studs at the desired height.

Make sure the brackets are level. The top of the frame will be 1/8"

above the top of the large wall bracket when mounted. You will

need at least 5/8" clearance above the bracket to hang the

screen. Figures 6 and 7 show the proper orientation for the

supplied wall brackets.

2. To install the lower large wall bracket, you must measure the

overall height of the screen frame and subtract 1/4". This is the

dimension from the top of the upper large wall bracket to the

bottom of the lower large wall bracket. See Figure 6.

3. Position the screen with the attached surface onto the top large

wall bracket as shown in Figure 6. Push down at the center of the

bottom frame rail to hook onto the lower large wall bracket.

Method 3 (Screens Over 96"

In Viewing Width) Cleaning

Da-Tex®, Dual Vision, Pearlescent, Cinema Vision, Da-Mat®,

High Contrast Da-Mat®, Audio Vision, High Contrast Audio

Vision, High Contrast Cinema Vision and High Contrast

Cinema Perf surfaces can be cleaned as follows:

Using a white clean cloth (100% cotton preferred) that is

dampened with clear water, gently wipe the area in one direction.

Do not use a circular motion. Using a dry 100% cotton cloth,

wipe dry after each cleaning session. To clean a stubborn stain

or a sticky surface, use denatured alcohol (methanol or methyl

alcohol) following the same procedure as for water.

Figure 7

Large Wall

Brackets

3Pieces

LIMITED ONE YEAR WARRANTY ON DALITE PRESENTATION PRODUCTS

Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in

materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly

operated according to Da-Lite's instructions and are not damaged due to improper handling or treatment after shipment from the

factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered

with or repaired by a person other than authorized Da-Lite personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise.

Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite,

transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.

To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of itness for use,

or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives

you speciic legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED

BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION

OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137,

Warsaw, IN 465810137, (574) 2678101, (800) 6223737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DALITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS

WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DALITE WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

86478

A Milestone AV Technologies Brand

3100 North Detroit Street

Warsaw, Indiana 46582

P: 574.267.8101 or 800.622.3737

F: 574.267.7804 or 877.325.4832

E: info@da-lite.com

www.da-lite.com

DL–0282 01.14