DELL 3046 User Manual

Displayed below is the user manual for 3046 by DELL which is a product in the PCs/Workstations category. This manual has pages.

Related Manuals

DELL 3046 Manual

OptiPlex 3046 - Small Form Factor

Owner's Manual

Regulatory Model: D11S

Regulatory Type: D11S001

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the

problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

Dell logo are trademarks of Dell Inc. in the United States and/or other jurisdictions. All other marks and names mentioned herein may be

trademarks of their respective companies.

2016 - 06

Rev. A00

Contents

1 Working on your computer................................................................................................................................... 5

Before working inside your computer................................................................................................................... 5

Turning off your computer.......................................................................................................................................5

After working inside your computer.......................................................................................................................5

2 Removing and installing components.................................................................................................................6

Recommended tools................................................................................................................................................. 6

Removing the cover...................................................................................................................................................6

Installing the cover..................................................................................................................................................... 6

Removing the front bezel..........................................................................................................................................7

Installing the front bezel............................................................................................................................................7

Removing the fan duct.............................................................................................................................................. 7

Installing the fan duct................................................................................................................................................ 8

Removing the memory module.............................................................................................................................. 8

Installing the memory module................................................................................................................................ 8

Removing the intrusion switch................................................................................................................................9

Installing the intrusion switch.................................................................................................................................. 9

Removing the expansion card................................................................................................................................. 9

Installing the expansion card................................................................................................................................. 10

Removing the hard drive assembly.......................................................................................................................10

Removing the hard drive from the hard drive bracket......................................................................................11

Installing the hard drive into the hard drive bracket..........................................................................................11

Installing the hard drive assembly......................................................................................................................... 12

Removing the optical drive.....................................................................................................................................12

Installing the optical drive....................................................................................................................................... 13

Removing the system fan........................................................................................................................................14

Installing the system fan..........................................................................................................................................14

Removing the heat sink assembly.........................................................................................................................14

Installing the heat sink assembly........................................................................................................................... 15

Removing the processor......................................................................................................................................... 15

Installing the processor........................................................................................................................................... 16

Removing the VGA daughter board......................................................................................................................16

Installing the VGA daughter board........................................................................................................................ 17

Removing the power supply unit (PSU)................................................................................................................17

Installing the power supply unit (PSU)..................................................................................................................18

Removing the power switch...................................................................................................................................19

Installing the power switch.....................................................................................................................................19

Removing the SD card reader................................................................................................................................19

Installing the SD card reader..................................................................................................................................20

Removing the system board..................................................................................................................................20

Installing the system board.................................................................................................................................... 22

System board layout................................................................................................................................................ 23

Contents 3

3 Troubleshooting your computer........................................................................................................................24

Diagnostic power LED codes.................................................................................................................................24

Diagnostic error messages.....................................................................................................................................25

System error messages........................................................................................................................................... 28

4 System Setup..........................................................................................................................................................29

Boot Sequence..........................................................................................................................................................29

Navigation keys.........................................................................................................................................................29

System Setup overview........................................................................................................................................... 30

Accessing System Setup......................................................................................................................................... 30

System Setup options..............................................................................................................................................30

Updating the BIOS ...................................................................................................................................................37

System and setup password...................................................................................................................................38

Assigning a system password and setup password.....................................................................................38

Deleting or changing an existing system and/or setup password...........................................................39

5 Specifications.........................................................................................................................................................40

6 Contacting Dell......................................................................................................................................................45

Owner's Manual 4

Working on your computer

Before working inside your computer

To avoid damaging your computer, perform the following steps before you begin working inside the computer.

1 Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

2 Turn off your computer (see Turning off your computer).

CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable

from the network device.

3 Disconnect all network cables from the computer.

4 Disconnect your computer and all attached devices from their electrical outlets.

5 Press and hold the power button while the computer is unplugged to ground the system board.

6 Remove the cover.

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface,

such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to

dissipate static electricity, which could harm internal components.

Turning off your computer

After working inside your computer

After you complete any replacement procedure, ensure that you connect any external devices, cards, and cables before turning

on your computer.

1 Replace the cover.

CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the

computer.

2 Connect any telephone or network cables to your computer.

3 Connect your computer and all attached devices to their electrical outlets.

4 Turn on your computer.

5 If required, verify that the computer works correctly by running Dell Diagnostics.

Working on your computer 5

Removing and installing components

This section provides detailed information on how to remove or install the components from your computer.

Recommended tools

The procedures in this document require the following tools:

• Small flat blade screwdriver

• Phillips screwdriver

• Small plastic scribe

Removing the cover

1 Follow the procedure in Before Working Inside Your Computer.

2 To remove the cover:

a Loosen the captive screws that secure the cover to the computer [1].

b Slide the cover toward the back of the computer [2].

c Lift the cover from the computer [3].

Installing the cover

1 Place the cover on the computer and slide the cover until it clicks into place.

2 Tighten the captive screws to secure the cover to the computer.

3 Follow the procedure in After Working Inside Your Computer

Removing and installing components 6

Removing the front bezel

1 Follow the procedure in Before Working Inside Your Computer.

2 Remove the cover.

3 To remove the front bezel:

a Lift the tabs to release the front bezel from the computer [1].

b Remove the front bezel from the computer [2].

Installing the front bezel

1 Insert the tabs on the bezel into the slots on the computer.

2 Press the bezel until the tabs clicks into place.

3 Install the cover.

4 Follow the procedure in After Working Inside Your Computer

Removing the fan duct

1 Follow the procedure in Before Working Inside Your Computer.

2 Remove the cover.

3 To remove the fan duct:

a Holding the touch points, pull the fan duct bracket to release the fan duct [1].

b Lift the fan duct away from the computer [2].

Removing and installing components 7

Installing the fan duct

1 Align the slots on the fan duct, with the screws on the heat sink.

2 Insert the fan duct until it clicks into place.

3 Install the cover.

4 Follow the procedure in After Working Inside Your Computer.

Removing the memory module

1 Follow the procedure in Before Working Inside Your Computer.

2 Remove the:

acover

bfan duct

chard drive assembly

doptical drive

3 To remove the memory module:

a Press the memory module retention tabs on both sides of the memory module.

b Lift the memory module from the memory module connector on the system board.

Installing the memory module

1 Align the notch on the memory module with the tab on the memory module connector.

2 Insert the memory module into the memory module socket.

3 Press the memory module until the memory module retention tabs click into place.

4 Install the:

aoptical drive

bhard drive assembly

Removing and installing components 8

cfan duct

dcover

5 Follow the procedure in After Working Inside Your Computer.

Removing the intrusion switch

1 Follow the procedure in Before Working Inside Your Computer.

2 Remove the:

acover

bfan duct

3 To remove the intrusion switch:

a Disconnect the intrusion switch cable from the connector on the system board [1][2].

b Slide the intrusion switch and lift it away from the computer [3].

Installing the intrusion switch

1 Insert the intrusion switch into the slot on the chassis.

2 Connect the intrusion switch cable to the system board.

3 Install the:

afan duct

bcover

4 Follow the procedure in After Working Inside Your Computer.

Removing the expansion card

1 Follow the procedure in Before Working Inside Your Computer.

2 Remove the:

acover

bfan duct

3 To remove the expansion card:

a Pull the metal tab to open the expansion card latch [1].

b Pull the tab forward [2] and pull the expansion card from the connector on the computer [3].

Removing and installing components 9

Installing the expansion card

1 Insert the expansion card into the connector on the system board.

2 Press the expansion card until it clicks into place.

3 Close the expansion card latch and press it until it clicks into place.

4 Install the:

afan duct

bcover

5 Follow the procedure in After Working Inside Your Computer.

Removing the hard drive assembly

1 Follow the procedure in Before Working Inside Your Computer.

2 Remove the:

acover

bfan duct

3 Disconnect the data and power cables from the connectors on the hard drive.

4 To remove the hard drive assembly:

a Pull the hard drive release handle forward to release the hard drive bracket from the computer [1].

b Lift the hard drive assembly away from the computer [2].

Removing and installing components 10

Removing the hard drive from the hard drive

bracket

1 Follow the procedure in Before Working Inside Your Computer.

2 Remove the:

acover

bbezel

chard drive assembly

3 To remove the hard drive bracket:

a Pull the hard drive bracket to release the hard drive [1].

b Lift the hard drive out of the hard drive bracket [2].

Installing the hard drive into the hard drive

bracket

1 Insert the hard drive into the hard drive bracket until it clicks into place.

2 Install the:

ahard drive assembly

bbezel

ccover

3 Follow the procedure in After Working Inside Your Computer.

Removing and installing components 11

Installing the hard drive assembly

1 Insert the hard drive assembly into the slot on the computer.

2 Connect the power cable to the slot on the hard drive bracket.

3 Install the:

afan duct

bcover

4 Follow the procedure in After Working Inside Your Computer.

Removing the optical drive

1 Follow the procedure in Before Working Inside Your Computer.

2 Remove the:

acover

bfront bezel

chard drive assembly

3 To release the optical drive:

a Remove the hard drive connector cables from the optical drive latch [1].

b Slide the blue latch to the unlock position [2].

4 To remove the optical drive:

a Holding the blue latch [1], lift the optical drive cage and disconnect the cables from the optical drive. [2]

b Lift the optical drive cage away from the computer [3].

Removing and installing components 12

5 To remove the optical drive from the optical drive cage:

a Press the optical drive release latch [1] and slide the optical drive forward. [2]

b Remove the optical drive from the optical drive cage [3].

Installing the optical drive

1 Slide the optical drive into the optical drive cage.

2 Align the tabs on the optical cage with the slots on the computer.

3 Lower the optical drive cage into the computer and lock the latch.

4 Connect the data and power cables to the optical drive.

5 Install the:

ahard drive assembly

bfront bezel

ccover

6 Follow the procedure in After Working Inside Your Computer.

Removing and installing components 13

Removing the system fan

1 Follow the procedure in Before Working Inside Your Computer.

2 Remove the:

acover

bfront bezel

chard drive assembly

doptical drive

3 To remove the system fan:

a Disconnect the system fan cable from the system board [1].

b Slide the fan grommets toward the slot on the back wall [2].

c Lift the fan away from the computer. [3]

Installing the system fan

1 Place the system fan in the computer.

2 Pass the grommets through the chassis and slide outward along the groove to secure it in place.

3 Connect the system fan cable to the system board.

4 Install the:

aoptical drive

bhard drive assembly

cfront bezel

dcover

5 Follow the procedure in After Working Inside Your Computer.

Removing the heat sink assembly

1 Follow the procedure in Before Working Inside Your Computer.

2 Remove the:

acover

bfront bezel

cfan duct

dhard drive assembly

eoptical drive

3 To remove the heat sink assembly:

a Disconnect the heat sink cable from the system board. [1]

Removing and installing components 14

b Loosen the captive screws that secure the heat sink assembly and lift it away from the computer [2] [3].

Installing the heat sink assembly

1 Place the heat sink assembly onto the processor.

2 Tighten the captive screws to secure the heat sink assembly to the system board.

3 Connect the heat sink cable to the system board.

4 Install the:

afan duct

boptical drive

chard drive assembly

dfront bezel

ecover

5 Follow the procedure in After Working Inside Your Computer.

Removing the processor

1 Follow the procedure in Before Working Inside Your Computer.

2 Remove the:

acover

bfront bezel

chard drive assembly

doptical drive

efan duct

fheat sink

3 To remove the processor:

a Release the socket lever by pushing the lever down and out from under the tab on the processor shield [1].

b Lift the lever upward and lift the processor shield [2].

c Lift the processor out of the socket [3].

Removing and installing components 15

Installing the processor

1 Align the processor with the socket keys.

2 Align the pin-1 indicator of the processor with the triangle on the socket.

3 Place the processor on the socket such that the slots on the processor align with the socket keys.

4 Close the processor shield by sliding it under the retention screw.

5 Lower the socket lever and push it under the tab to lock it.

6 Install the:

aheat sink

bfan duct

coptical drive

dhard drive assembly

efront bezel

fcover

7 Follow the procedure in After Working Inside Your Computer.

Removing the VGA daughter board

1 Follow the procedure in Before Working Inside Your Computer.

2 Remove the:

acover

bfan duct

3 To remove the VGA daughter board:

a Remove the screws that secure the VGA connector to the computer [1].

b Slide the VGA connector to release it from the computer [2].

c Remove the screw that secures the VGA daughter board to the computer [3].

d Lift the VGA daughter board using the handle to remove it from the computer [4].

Removing and installing components 16

Installing the VGA daughter board

1 Align the VGA daughter board with the screw holder on the system board.

2 Tighten the screw to secure the VGA daughter board to the system board.

3 Insert the VGA connector into the slot at the back of the computer.

4 Tighten the screws to secure the VGA connector to the computer.

5 Install the:

afan duct

bcover

6 Follow the procedure in After Working Inside Your Computer.

Removing the power supply unit (PSU)

1 Follow the procedure in Before Working Inside Your Computer.

2 Remove the:

acover

bfront bezel

chard drive assembly

doptical drive

efan duct

3 To release the PSU:

a Disconnect the power cable from the system board [1] [2].

b Unroute the power cables from the retention clips on the chassis [3] [4].

4 To remove the PSU:

a Disconnect the power cable from the system board [1] [2].

b Lift the cables away from the computer [3].

c Remove the screws that secure the PSU to the computer [4].

Removing and installing components 17

5 Press the blue release tab [1], slide the PSU and lift it away from the computer [2].

Installing the power supply unit (PSU)

1 Insert the PSU in the chassis and slide it toward the back of the computer to secure it.

2 Tighten the screws to secure the PSU to the back of the computer.

3 Route the PSU cables through the retention clips.

4 Connect the power cables to the system board.

5 Install the:

afan duct

boptical drive

chard drive assembly

dfront bezel

ecover

6 Follow the procedure in After Working Inside Your Computer.

Removing and installing components 18

Removing the power switch

1 Follow the procedure in Before Working Inside Your Computer.

2 Remove the:

acover

bfront bezel

chard drive assembly

doptical drive

epower supply unit

3 To remove the power switch:

a Disconnect the power switch cable from the system board [1].

b Press the power switch retention tabs and remove it from the chassis [2] [3].

Installing the power switch

1 Slide the power switch module into the slot on the chassis until it clicks into place.

2 Connect the power switch cable to the connector on the system board.

3 Install the:

apower supply unit

boptical drive

chard drive assembly

dfront bezel

ecover

4 Follow the procedure in After Working Inside Your Computer.

Removing the SD card reader

1 Follow the procedure in Before Working Inside Your Computer.

2 Remove the:

acover

bfront bezel

chard drive assembly

doptical drive

epower supply unit

3 To remove the SD card reader:

a Remove the power supply unit cables from the retention clips on the SD card reader enclosure [1].

Removing and installing components 19

b Remove the screws that secure the SD card reader and lift it away from the computer [2] [3].

Installing the SD card reader

1 Place the SD card reader on the chassis.

2 Tighten the screws that secure the SD card reader to the computer.

3 Route the power supply unit cables into the retention clips.

4 Install the:

apower supply unit

boptical drive

chard drive assembly

dfront bezel

ecover

5 Follow the procedure in After Working Inside Your Computer.

Removing the system board

1 Follow the procedure in Before Working Inside Your Computer.

2 Remove the:

acover

bfan duct

cfront bezel

dmemory module

ehard drive assembly

foptical drive

gexpansion card

hSD card reader

iVGA daughter board

jheat sink

kprocessor

3 To remove the I/O panel:

a Remove the screw that secures the I/O panel to the chassis [1].

b Remove the I/O panel from the computer [2].

Removing and installing components 20

4 Disconnect all the cables connected to the system board.

5 To remove the system board:

a Remove the screws that secure the system board to the computer [1].

b Slide the system board toward the front of the computer and lift it from the computer [2].

Removing and installing components 21

Installing the system board

1 Hold the system board by its edges and angle it toward the back of the computer.

2 Lower the system board into the computer until the connectors at the back of the system board align with the slots on the

back wall of the computer, and the screw holes on the system board align with the standoffs on the computer.

3 Tighten the screws that secure the system board to the computer.

4 Connect the cables to the system board.

5 Install the:

aVGA daughter board

bSD card reader

cexpansion card

dprocessor

eheat sink

foptical drive

ghard drive assembly

hfront bezel

ifan duct

jcover

6 Place the I/O panel on the chassis.

7 Tighten the screws to secure the I/O panel to the chassis.

8 Follow the procedure in After Working Inside Your Computer.

Removing and installing components 22

System board layout

1. PCIex16 connector 2. PCIex1 connector

3. RJ-45/USB 2.0 connector 4. USB 3.0 connector

5. Keyboard MS connector (optional) 6. DisplayPort connector

7. HDMI connector 8. Line-out connector

9. CPU power connector 10. Intrusion switch connector

11. VGA daughter board connector 12. Processor

13. CPU fan connector 14. Memory module connectors

15. Power switch connector 16. Media card reader connector (optional)

17. System fan connector 18. Hard drive activity LED

19. Universal audio jack 20. USB 2.0 connector

21. USB 3.0 connector 22. ATX power connector

23. SATA2 connector 24. Password clear jumper

25. Service mode jumper 26. Speaker connector

27. SATA hard drive power cable connector 28. Internal USB connector

29. SATA connector 30. Coin cell battery

31. Clear CMOS jumper

Removing and installing components 23

Troubleshooting your computer

You can troubleshoot your computer using indicators like diagnostic lights, beep codes, and error messages during the

operation of the computer.

Diagnostic power LED codes

Table 1. Diagnostic power LED codes

Power LED light status Possible cause Troubleshooting steps

Off The computer is either turned

off or is not receiving power

or in Hibernation mode.

• Re-seat the power cable in

the power connector on

the back of the computer

and the electrical outlet.

• If the computer is plugged

into a power strip, ensure

that the power strip is

plugged into an electrical

outlet and is turned on.

Also, bypass power

protection devices, power

strips, and power

extension cables to verify

that the computer turns

on properly.

• Ensure the electrical outlet

is working by testing it

with another device, such

as a lamp.

Steady/blinking amber Computer fails to complete

POST or processor failure. • Remove and reinstall any

cards.

• Remove and reinstall the

graphics card, if

applicable.

• Ensure the power cable is

connected to the system

board and processor.

Slow Blinking white light Computer is in sleep mode. • Press the power button to

bring the computer out of

the sleep mode.

• Ensure all power cables

are securely connected to

the system board.

• Ensure the main power

cable and front panel

cable are connected to

the system board.

Steady white The computer is fully

functional and in the On state.

If the computer is not

responding, do the following:

• Ensure the display is

connected and turned on.

Troubleshooting your computer 24

Power LED light status Possible cause Troubleshooting steps

• If the display is connected

and turned on, listen for a

beep code.

Diagnostic error messages

Table 2. Diagnostic error messages

Error messages Description

AUXILIARY DEVICE FAILURE The touchpad or external mouse may be faulty. For an

external mouse, check the cable connection. Enable the

Pointing Device option in the System Setup program.

BAD COMMAND OR FILE NAME Ensure that you have spelled the command correctly, put

spaces in the proper place, and used the correct path name.

CACHE DISABLED DUE TO FAILURE The primary cache internal to the microprocessor has failed.

Contact Dell.

CD DRIVE CONTROLLER FAILURE The optical drive does not respond to commands from the

computer.

DATA ERROR The hard drive cannot read the data.

DECREASING AVAILABLE MEMORY One or more memory modules may be faulty or improperly

seated. Reinstall the memory modules or, if necessary,

replace them.

DISK C: FAILED INITIALIZATION The hard drive failed initialization. Run the hard drive tests in

Dell Diagnostics.

DRIVE NOT READY The operation requires a hard drive in the bay before it can

continue. Install a hard drive in the hard drive bay.

ERROR READING PCMCIA CARD The computer cannot identify the ExpressCard. Reinsert the

card or try another card.

EXTENDED MEMORY SIZE HAS CHANGED The amount of memory recorded in non-volatile memory

(NVRAM) does not match the memory module installed in the

computer. Restart the computer. If the error appears again,

Contact Dell

THE FILE BEING COPIED IS TOO LARGE FOR THE

DESTINATION DRIVE

The file that you are trying to copy is too large to fit on the

disk, or the disk is full. Try copying the file to a different disk or

use a larger capacity disk.

A FILENAME CANNOT CONTAIN ANY OF THE FOLLOWING

CHARACTERS: \ / : * ? " < > | -

Do not use these characters in filenames.

GATE A20 FAILURE A memory module may be loose. Reinstall the memory

module or, if necessary, replace it.

GENERAL FAILURE The operating system is unable to carry out the command.

The message is usually followed by specific information. For

example, Printer out of paper. Take the

appropriate action.

HARD-DISK DRIVE CONFIGURATION ERROR The computer cannot identify the drive type. Shut down the

computer, remove the hard drive, and boot the computer

from an optical drive. Then, shut down the computer, reinstall

Troubleshooting your computer 25

Error messages Description

the hard drive, and restart the computer. Run the Hard Disk

Drive tests in Dell Diagnostics.

HARD-DISK DRIVE CONTROLLER FAILURE 0 The hard drive does not respond to commands from the

computer. Shut down the computer, remove the hard drive,

and boot the computer from an optical drive. Then, shut

down the computer, reinstall the hard drive, and restart the

computer. If the problem persists, try another drive. Run the

Hard Disk Drive tests in Dell Diagnostics.

HARD-DISK DRIVE FAILURE The hard drive does not respond to commands from the

computer. Shut down the computer, remove the hard drive,

and boot the computer from an optical drive. Then, shut

down the computer, reinstall the hard drive, and restart the

computer. If the problem persists, try another drive. Run the

Hard Disk Drive tests in Dell Diagnostics.

HARD-DISK DRIVE READ FAILURE The hard drive may be defective. Shut down the computer,

remove the hard drive, and boot the computer from an

optical. Then, shut down the computer, reinstall the hard

drive, and restart the computer. If the problem persists, try

another drive. Run the Hard Disk Drive tests in Dell

Diagnostics.

INSERT BOOTABLE MEDIA The operating system is trying to boot to non-bootable

media, such as an optical drive. Insert bootable media.

INVALID CONFIGURATION INFORMATION-PLEASE RUN

SYSTEM SETUP PROGRAM

The system configuration information does not match the

hardware configuration. The message is most likely to occur

after a memory module is installed. Correct the appropriate

options in the system setup program.

KEYBOARD CLOCK LINE FAILURE For external keyboards, check the cable connection. Run the

Keyboard Controller test in Dell Diagnostics.

KEYBOARD CONTROLLER FAILURE For external keyboards, check the cable connection. Restart

the computer, and avoid touching the keyboard or the mouse

during the boot routine. Run the Keyboard Controller test in

Dell Diagnostics.

KEYBOARD DATA LINE FAILURE For external keyboards, check the cable connection. Run the

Keyboard Controller test in Dell Diagnostics.

KEYBOARD STUCK KEY FAILURE For external keyboards or keypads, check the cable

connection. Restart the computer, and avoid touching the

keyboard or keys during the boot routine. Run the Stuck Key

test in Dell Diagnostics.

LICENSED CONTENT IS NOT ACCESSIBLE IN

MEDIADIRECT

Dell MediaDirect cannot verify the Digital Rights Management

(DRM) restrictions on the file, so the file cannot be played.

MEMORY ADDRESS LINE FAILURE AT ADDRESS, READ

VALUE EXPECTING VALUE

A memory module may be faulty or improperly seated.

Reinstall the memory module or, if necessary, replace it.

MEMORY ALLOCATION ERROR The software you are attempting to run is conflicting with the

operating system, another program, or a utility. Shut down the

computer, wait for 30 seconds, and then restart it. Run the

program again. If the error message still appears, see the

software documentation.

Troubleshooting your computer 26

Error messages Description

MEMORY DOUBLE WORD LOGIC FAILURE AT ADDRESS,

READ VALUE EXPECTING VALUE

A memory module may be faulty or improperly seated.

Reinstall the memory module or, if necessary, replace it.

MEMORY ODD/EVEN LOGIC FAILURE AT ADDRESS, READ

VALUE EXPECTING VALUE

A memory module may be faulty or improperly seated.

Reinstall the memory module or, if necessary, replace it.

MEMORY WRITE/READ FAILURE AT ADDRESS, READ

VALUE EXPECTING VALUE

A memory module may be faulty or improperly seated.

Reinstall the memory module or, if necessary, replace it.

NO BOOT DEVICE AVAILABLE The computer cannot find the hard drive. If the hard drive is

your boot device, ensure that the drive is installed, properly

seated, and partitioned as a boot device.

NO BOOT SECTOR ON HARD DRIVE The operating system may be corrupted, Contact Dell.

NO TIMER TICK INTERRUPT A chip on the system board may be malfunctioning. Run the

System Set tests in Dell Diagnostics.

NOT ENOUGH MEMORY OR RESOURCES. EXIT SOME

PROGRAMS AND TRY AGAIN

You have too many programs open. Close all windows and

open the program that you want to use.

OPERATING SYSTEM NOT FOUND Reinstall the operating system. If the problem persists,

Contact Dell.

OPTIONAL ROM BAD CHECKSUM The optional ROM has failed. Contact Dell.

SECTOR NOT FOUND The operating system cannot locate a sector on the hard

drive. You may have a defective sector or corrupted File

Allocation Table (FAT) on the hard drive. Run the Windows

error-checking utility to check the file structure on the hard

drive. See Windows Help and Support for instructions (click

Start > Help and Support). If a large number of sectors are

defective, back up the data (if possible), and then format the

hard drive.

SEEK ERROR The operating system cannot find a specific track on the hard

drive.

SHUTDOWN FAILURE A chip on the system board may be malfunctioning. Run the

System Set tests in Dell Diagnostics. If the message

reappears, Contact Dell.

TIME-OF-DAY CLOCK LOST POWER System configuration settings are corrupted. Connect your

computer to an electrical outlet to charge the battery. If the

problem persists, try to restore the data by entering the

System Setup program, then immediately exit the program. If

the message reappears, Contact Dell.

TIME-OF-DAY CLOCK STOPPED The reserve battery that supports the system configuration

settings may require recharging. Connect your computer to

an electrical outlet to charge the battery. If the problem

persists, Contact Dell.

TIME-OF-DAY NOT SET-PLEASE RUN THE SYSTEM SETUP

PROGRAM

The time or date stored in the system setup program does not

match the system clock. Correct the settings for the Date and

Time options.

TIMER CHIP COUNTER 2 FAILED A chip on the system board may be malfunctioning. Run the

System Set tests in Dell Diagnostics.

UNEXPECTED INTERRUPT IN PROTECTED MODE The keyboard controller may be malfunctioning, or a memory

module may be loose. Run the System Memory tests and the

Keyboard Controller test in Dell Diagnostics or Contact Dell.

Troubleshooting your computer 27

Error messages Description

X:\ IS NOT ACCESSIBLE. THE DEVICE IS NOT READY Insert a disk into the drive and try again.

System error messages

Table 3. System error messages

System message Description

Alert! Previous attempts at booting this system

have failed at checkpoint [nnnn]. For help in

resolving this problem, please note this

checkpoint and contact Dell Technical Support

The computer failed to complete the boot routine three

consecutive times for the same error.

CMOS checksum error RTC is reset, BIOS Setup default has been loaded.

CPU fan failure CPU fan has failed.

System fan failure System fan has failed.

Hard-disk drive failure Possible hard disk drive failure during POST.

Keyboard failure Keyboard failure or loose cable. If reseating the cable does

not solve the problem, replace the keyboard.

No boot device available No bootable partition on hard disk drive, the hard disk drive

cable is loose, or no bootable device exists.

• If the hard drive is your boot device, ensure that the cables

are connected and that the drive is installed properly and

partitioned as a boot device.

• Enter system setup and ensure that the boot sequence

information is correct.

No timer tick interrupt A chip on the system board might be malfunctioning or

motherboard failure.

NOTICE - Hard Drive SELF MONITORING SYSTEM has

reported that a parameter has exceeded its

normal operating range. Dell recommends that

you back up your data regularly. A parameter

out of range may or may not indicate a

potential hard drive problem

S.M.A.R.T error, possible hard disk drive failure.

Troubleshooting your computer 28

System Setup

System Setup enables you to manage your computer hardware and specify BIOS level options. From the System Setup, you

can:

• Change the NVRAM settings after you add or remove hardware

• View the system hardware configuration

• Enable or disable integrated devices

• Set performance and power management thresholds

• Manage your computer security

Topics:

• Boot Sequence

• Navigation keys

• System Setup overview

• Accessing System Setup

• System Setup options

• Updating the BIOS

• System and setup password

Boot Sequence

Boot Sequence allows you to bypass the System Setup‐defined boot device order and boot directly to a specific device (for

example: optical drive or hard drive). During the Power-on Self Test (POST), when the Dell logo appears, you can:

• Access System Setup by pressing F2 key

• Bring up the one-time boot menu by pressing F12 key

The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot menu options

are:

• Removable Drive (if available)

• STXXXX Drive

NOTE: XXX denotes the SATA drive number.

• Optical Drive

• Diagnostics

NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.

The boot sequence screen also displays the option to access the System Setup screen.

Navigation keys

NOTE: For most of the System Setup options, changes that you make are recorded but do not take effect until you restart

the system.

System Setup 29

Keys Navigation

Up arrow Moves to the previous field.

Down arrow Moves to the next field.

Enter Selects a value in the selected field (if applicable) or follow the link in the field.

Spacebar Expands or collapses a drop‐down list, if applicable.

Tab Moves to the next focus area.

NOTE: For the standard graphics browser only.

Esc Moves to the previous page until you view the main screen. Pressing Esc in the main screen displays a

message that prompts you to save any unsaved changes and restarts the system.

F1 Displays the System Setup help file.

System Setup overview

System Setup allows you to:

• Change the system configuration information after you add, change, or remove any hardware in your computer.

• Set or change a user-selectable option such as the user password.

• Read the current amount of memory or set the type of hard drive installed.

Before you use System Setup, it is recommended that you write down the System Setup screen information for future

reference.

CAUTION: Unless you are an expert computer user, do not change the settings for this program. Certain changes can

cause your computer to work incorrectly.

Accessing System Setup

1 Turn on (or restart) your computer.

2 After the white Dell logo appears, press F2 immediately.

The System Setup page is displayed.

NOTE: If you wait too long and the operating system logo appears, wait until you see the desktop. Then, shut down or

restart your computer and try again.

NOTE: After the Dell logo appears, you can also press F12 and then select BIOS setup.

System Setup options

NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not appear.

Table 4. General

Option Description

System Information Displays the following information:

• System Information: Displays BIOS Version, Service Tag, Asset Tag, Ownership Date,

Manufacture Date, and the Express Service Code.

• Memory Information: Displays Memory Installed, Memory Available, Memory Speed,

Memory Channels Mode, Memory Technology, DIMM 1 Size,, DIMM 2 Size, DIMM 3

Size, and DIMM 4 Size.

• PCI Information: Displays SLOT1, SLOT2, SLOT3, SLOT4, and SLOT5_M.2

System Setup 30

Option Description

• Processor Information: Displays Processor Type, Core Count, Processor ID, Current

Clock Speed, Minimum Clock Speed, Maximum Clock Speed, Processor L2 Cache,

Processor L3 Cache, HT Capable, and 64-Bit Technology.

• Device Information: Displays SATA-0, LOM MAC Address, Video Controller, Audio

Controller, Wi-Fi Device, and Bluetooth Device.

Boot Sequence Allows you to specify the order in which the computer attempts to find an operating system

from the devices specified in this list.

• Legacy

• UEFI

Advanced Boot Options Allows you to select the Enable Legacy Option ROMs option, when in UEFI boot mode. By

default, this option is enabled.

Date/Time Allows you to set the date and time settings. Changes to the system date and time take

effect immediately.

Table 5. System configuration

Option Description

Integrated NIC Allows you to control the on-board LAN controller. The options are:

• Disabled

• Enabled (default)

• Enabled w/PXE

• Enabled w/Cloud Desktop

NOTE: Depending on the computer and its installed devices, the items listed in this

section may or may not appear.

WIDI Allows you to connect to display through WiFi. WIDI requires Intel WiFi card, Intel graphics,

and WIDI receiver in display (or WIDI compliant display). To install the WIDI application, see

the Dell.com/support site to download the WIDI application.

NOTE: When installing the WIDI application, connect the display to Intel onboard

graphic output.

Serial Port Allows you to determine how the built-in serial port to operate. The options are:

• Disabled

• COM 1 – Default setting

• COM 2

• COM 3

• COM 4

SATA Operation Allows you to configure the operating mode of the integrated hard drive controller.

• Disabled = The SATA controllers are hidden

• ATA = SATA is configured for ATA mode

• RAID ON = SATA is configured to support RAID mode

Drives Allows you to enable or disable the various drives on-board:

• SATA-0

• SATA-1

• SATA-2

System Setup 31

Option Description

Smart Reporting This field controls whether hard drive errors for integrated drives are reported during system

startup. This option is disabled by default.

USB Configuration Allows you to enable or disable the integrated USB controller for:

• Enable Boot Support

• Enable Front USB Ports

• Enable Rear USB Ports

All the options are enabled by default.

Front USB Configuration Allows you to enable or disable the front USB ports. All the ports are enabled by default.

Back USB Configuration Allows you to enable or disable the back USB ports. All the ports are enabled by default.

USB PowerShare This option allows you to charge the external devices, such as mobile phones, music player.

This option is disabled by default.

Audio Allows you to enable or disable the integrated audio controller.

• Enable Microphone

• Enable Internal Speaker

Both the options are enabled by default.

Miscellaneous Devices Allows you to enable or disable the various on-board devices.

• Enable PCI Slot

• Enable Media Card (default option)

• Disable Media Card

Table 6. Video

Option Description

Primary Display Allows you to select the primary display when multiple controllers are available in the

system.

• Auto

• Intel HD Graphics

NOTE: If you do not select Auto, the on-board graphics device will be present and

enabled.

Table 7. Security

Option Description

Admin Password Allows you to set, change, and delete the admin password.

System Password Allows you to set, change, and delete the system password.

Internal HDD-0 Password Allows you to set, change, and delete the computer’s internal HDD.

Strong Password This option lets you enable or disable strong passwords for the system.

Password Configuration Allows you to control the minimum and maximum number of characters allowed for a

administrative password and the system password.

System Setup 32

Option Description

Password Bypass This option lets you bypass the System (Boot) Password and the internal HDD password

prompts during a system restart.

• Disabled — Always prompt for the system and internal HDD password when they are set.

This option is disabled by default.

• Reboot Bypass — Bypass the password prompts on Restarts (warm boots).

NOTE: The system will always prompt for the system and internal HDD passwords

when powered on from the off state (a cold boot). Also, the system will always prompt

for passwords on any module bay HDDs that may be present.

Password Change This option lets you determine whether changes to the System and Hard Disk passwords are

permitted when an administrator password is set.

Allow Non-Admin Password Changes - This option is enabled by default.

TPM 1.2 Security Allows you to control whether the Trusted Platform Module (TPM) is visible to the operating

system.

• TPM On (default)

• Clear

• PPI Bypass for Enable Commands

• PPI Bypass for Disable Commands

• Disabled

• Enabled (default)

Computrace This field lets you Activate or Disable the BIOS module interface of the optional Computrace

Service from Absolute Software. Enables or disables the optional Computrace service

designed for asset management.

•Deactivate - This option is disabled by default.

• Disable

• Activate

Chassis Intrusion Allows you to control the chassis intrusion feature. You can set this option to:

• Enable

• Disable

•On-Silent — Enabled by default if chassis intrusion is detected.

CPU XD Support Allows you to enable or disable the Execute Disable mode of the processor. This option is

enabled by default.

OROM Keyboard Access This option determines whether users are able to enter Option ROM Configuration screens

via hotkeys during boot. Specifically, these settings are capable of preventing access to Intel

RAID (CTRL+I) or Intel Management Engine BIOS Extension (CTRL+P/F12)

•Enable — User may enter OROM configuration screens via the hotkey.

•One-Time Enable — User may enter OROM configuration screens via the hotkeys on

next boot only. After next boot, the setting will revert to disabled.

•Disable — User may not enter OROM configuration screens via the hotkey.

This option is set to Enable by default.

Admin Setup Lockout Allows you to enable or disable the option to enter Setup when an Administrative password

is set. This option is not set by default.

HDD Protection Support Allows you to enable or disable the HDD Protection feature. This option is an advanced

feature, which is intended to keep the HDD data secure and unchangeable. By default, this

option is disabled.

System Setup 33

Table 8. Secure boot

Option Description

Secure Boot Enable Allows you to enable or disable Secure Boot feature

• Disable

• Enable

Expert key Management Allows you to manipulate the security key databases only if the system is in Custom Mode.

The Enable Custom Mode option is disabled by default. The options are:

• PK

• KEK

• db

• dbx

If you enable the Custom Mode, the relevant options for PK, KEK, db, and dbx appear. The

options are:

•Save to File- Saves the key to a user-selected file

•Replace from File- Replaces the current key with a key from a user-selected file

•Append from File- Adds a key to the current database from a user-selected file

•Delete- Deletes the selected key

•Reset All Keys- Resets to default setting

•Delete All Keys- Deletes all the keys

NOTE: If you disable the Custom Mode, all the changes made will be erased and the

keys will restore to default settings.

Table 9. Intel software guard extensions

Option Description

Intel SGX Enable Allows you to enable or disable the Intel Software Guard Extensions to provide a secured

environment for running code/storing sensitive information in the context of the main

operating system.

• Disabled (default)

• Enabled

Enclave Memory Size Allows you to set the Intel SGX Enclave Reserve Memory Size.

• 32 MB

• 64 MB

• 128 MB

Table 10. Performance

Option Description

Multi Core Support This field specifies whether the process will have one or all cores enabled. This option is

enabled by default.

Intel SpeedStep Allows you to enable or disable the Intel SpeedStep mode of the processor. This option is

disabled by default.

C States Control Allows you to enable or disable additional processor sleep states. This option is disabled by

default.

System Setup 34

Option Description

Limited CPUID Value Allows you to limit the maximum value of the processor standard CPUID function. This

options is disable by default.

Intel TurboBoost Allows you to enable or disable the Intel TurboBoost mode of the processor. This option is

enabled by default.

HyperThread control Allows you to enable or disable HyperThreading in the processor.

Table 11. Power management

Option Description

AC Recovery Determines how the system responds when AC power is re-applied after a power loss. You

can set the AC Recovery to:

• Power Off

• Power On

• Last Power State

This option is Power Off by default.

Auto On Time Sets time to automatically turn on the computer. Time is kept in standard 12-hour format

(hour:minutes:seconds). Change the startup time by typing the values in the time and

AM/PM fields.

NOTE: This feature does not work if you turn off your computer using the switch on a

power strip or surge protector or if Auto Power is set to disabled.

Deep Sleep Control Allows you to define the controls when Deep Sleep is enabled.

• Disabled

• Enabled in S5 only

• Enabled in S4 and S5

This option is Disabled by default.

Fan Control Override Allows you to determine the speed of the system fan. When this option is enabled, the

system fan runs at the maximum speed. This option is disabled by default.

USB Wake Support Allows you to enable the USB devices to wake the computer from standby mode.

Wake on LAN/WWAN This option allows the computer to power up from the off state when triggered by a special

LAN signal. This feature only works when the computer is connected to AC power supply.

•Disabled - Does not allows the system to power on by special LAN signals when it

receives a wake-up signal from the LAN or wireless LAN.

•LAN or WLAN - Allows the system to be powered on by special LAN or wireless LAN

signals.

•LAN Only - Allows the system to be powered on by special LAN signals.

•LAN with PXE Boot - A wakeup packet sent to the system in either the S4 or S5 state,

that will cause the system to wake-up and immediately boot to PXE.

•WLAN Only - Allows the system to be powered on by special WLAN signals.

This option is Disabled by default.

Block Sleep Allows you to block entering to sleep (S3 state) in OS environment. This option is disabled by

default.

Intel Ready Mode Allows you to enable the capability of Intel Ready Mode Technology. This option is disabled

by default.

System Setup 35

Table 12. POST behavior

Option Description

Numlock LED Allows you to enable or disable the Numlock feature when your computer starts. This option

is enabled by default.

MEBx Hotkey Allows you to specify whether the MEBx Hotkey function should be enabled when the

system boots. This option is enabled by default.

Keyboard Errors Allows you to enable or disable the keyboard error reporting when the computer starts. This

option is enabled by default.

Fast Boot This option can speed up the boot process by bypassing some compatibility steps:

• Minimal — The system boots quickly, unless the BIOS has been updated, memory

changed, or the previous POST did not complete.

• Thorough — The system does not skip any steps in the boot process.

• Auto — This allows the operating system to control this setting (this works only when the

operating system supports Simple Boot Flag).

This option is set to Thorough by default.

Table 13. Virtualization support

Option Description

Virtualization This option specifies whether a Virtual Machine Monitor (VMM) can utilize the additional

hardware capabilities provided by Intel® Virtualization Technology. Enable Intel

Virtualization Technology - This option is disabled by default.

VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the additional hardware

capabilities provided by Intel® Virtualization technology for direct I/O. Enable Intel

Virtualization Technology for Direct I/O - This option is disabled by default.

Trusted Execution This option specifies whether a Measured Virtual Machine Monitor (MVMM) can utilize the

additional hardware capabilities provided by the Intel Trusted Execution Technology. This

option is disabled by default.

Table 14. Maintenance

Option Description

Service Tag Displays the Service Tag of your computer.

Asset Tag Allows you to create a system asset tag if an asset tag is not already set. This option is not set

by default.

SERR Messages Controls the SERR message mechanism. This option is not set by default. Some graphics

cards require that the SERR message mechanism be disabled.

Dell Development

Configuration

Allows you to turn on/off certain features to control the BIOS. This option is disabled by

default.

BIOS Downgrade Allows you to control flashing of the system firmware to the previous versions. This option is

enabled by default.

NOTE: If this option is not selected, the flashing of the system firmware to the previous

versions is blocked.

Data Wipe Allows you to securely erase the data from all the available internal storages, such as HDD,

SSD, mSATA, and eMMC. This option is disabled by default.

BIOS recovery Allows you to recover the corrupted BIOS conditions from the recovery files on the primary

hard drive or an external USB key.

System Setup 36

Table 15. Cloud desktop

Option Description

Server Lookup Method Allows you to specify how the cloud desktop software will lookup server addresses.

• Static

• DNS (Default)

Server Name Allows you to specify the name of the server

Server IP Address Specifies the primary static IP address of the cloud desktop server. The default IP address is

255.255.255.255

Server port Specifies the primary port of the cloud desktop. The default setting is 06910.

Client Address Method Specifies how the client will obtain the IP address.

• Static IP

• DHCP (Default)

Client IP address Specifies the static IP address of the client. The default IP address is 255.255.255.255

Client Subnet Mask Specifies the subnet mask address of the client. The default IP address is 255.255.255.255

Client Gateway Specifies the gateway address of the client. The default IP address is 255.255.255.255

DNS IP Address Specifies the DNS IP address of the client. The default IP address is 255.255.255.255

Domain Name Specifies the domain name of the client.

Advanced Allows you to turn on the Verbose mode for advanced debugging. This option is disabled by

default.

Table 16. System logs

Option Description

BIOS Events Displays the system event log and allows you to:

• Clear Log

• Mark all Entries

Table 17. Advanced configurations

Option Description

ASPM Allows you to activate the state power management.

• Auto (Default)

• Disabled

• L1 Only

Updating the BIOS

It is recommended to update your BIOS (System Setup), on replacing the system board or if an update is available. For laptops,

ensure that your computer battery is fully charged and connected to a power outlet

1 Restart the computer.

2 Go to Dell.com/support.

3 Enter the Service Tag or Express Service Code and click Submit.

System Setup 37

NOTE: To locate the Service Tag, click Where is my Service Tag?

NOTE: If you cannot find your Service Tag, click Detect My Product. Proceed with the instructions on screen.

4 If you are unable to locate or find the Service Tag, click the Product Category of your computer.

5 Choose the Product Type from the list.

6 Select your computer model and the Product Support page of your computer appears.

7 Click Get drivers and click View All Drivers.

The Drivers and Downloads page opens.

8 On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS.

9 Identify the latest BIOS file and click Download File.

You can also analyze which drivers need an update. To do this for your product, click Analyze System for Updates and

follow the instructions on the screen.

10 Select your preferred download method in the Please select your download method below window, click Download File.

The File Download window appears.

11 Click Save to save the file on your computer.

12 Click Run to install the updated BIOS settings on your computer.

Follow the instructions on the screen.

NOTE: It is recommended not to update the BIOS version for more than 3 revisions. For example: If you want to update the

BIOS from 1.0 to 7.0, then install version 4.0 first and then install version 7.0.

System and setup password

You can create a system password and a setup password to secure your computer.

Password type Description

System password Password that you must enter to log on to your system.

Setup password Password that you must enter to access and make changes to the BIOS settings of your computer.

CAUTION: The password features provide a basic level of security for the data on your computer.

CAUTION: Anyone can access the data stored on your computer if it is not locked and left unattended.

NOTE: Your computer is shipped with the system and setup password feature disabled.

Assigning a system password and setup password

You can assign a new System Password and/or Setup Password or change an existing System Password and/or Setup

Password only when Password Status is Unlocked. If the Password Status is Locked, you cannot change the System Password.

NOTE: If the password jumper is disabled, the existing System Password and Setup Password are deleted and you need not

provide the system password to log on to the computer.

To enter the system setup, press F2 immediately after a power-on or re-boot.

1 In the System BIOS or System Setup screen, select System Security and press Enter.

The System Security screen appears.

2 In the System Security screen, verify that Password Status is Unlocked.

3 Select System Password , enter your system password, and press Enter or Tab.

Use the following guidelines to assign the system password:

• A password can have up to 32 characters.

• The password can contain the numbers 0 through 9.

System Setup 38

• Only lower case letters are valid, upper case letters are not allowed.

• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

Re-enter the system password when prompted.

4 Type the system password that you entered earlier and click OK.

5 Select Setup Password, type your system password and press Enter or Tab.

A message prompts you to re-type the setup password.

6 Type the setup password that you entered earlier and click OK.

7 Press Esc and a message prompts you to save the changes.

8 Press Y to save the changes.

The computer reboots.

Deleting or changing an existing system and/or setup

password

Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing System

and/or Setup password. You cannot delete or change an existing System or Setup password, if the Password Status is Locked.

To enter the System Setup, press F2 immediately after a power-on or reboot.

1 In the System BIOS or System Setup screen, select System Security and press Enter.

The System Security screen is displayed.

2 In the System Security screen, verify that Password Status is Unlocked.

3 Select System Password, alter or delete the existing system password and press Enter or Tab.

4 Select Setup Password, alter or delete the existing setup password and press Enter or Tab.

NOTE: If you change the System and/or Setup password, re-enter the new password when promoted. If you delete the

System and/or Setup password, confirm the deletion when promoted.

5 Press Esc and a message prompts you to save the changes.

6 Press Y to save the changes and exit from System Setup.

The computer reboots.

System Setup 39

Specifications

NOTE: Offerings may vary by region. For more information regarding the configuration of your computer in:

• Windows 10, click or tap Start > Settings > System > About.

• Windows 8.1 and Windows 8, click or tap Start > PC Settings > PC and devices > PC Info.

• Windows 7, click Start , right-click My Computer, and then select Properties.

Table 18. Processor

Feature Specification

Processor type • 6th Generation Intel Core i3/i5/i7 series

• Intel Celeron

• Intel PDC

Total cache Up to 8 MB cache depending on processor type

Table 19. Memory

Feature Specification

Type DDR4

Speed 1600 MHz

Connectors Two UDIMM slots

Memory module capacity 2 GB, 4 GB and 8 GB

Minimum memory 2 GB

NOTE: The minimum memory may differ based on the

operating system installed on the computer.

Maximum memory 16 GB

NOTE: Each UDIMM slot supports a minimum of 4 GB and a

maximum of 8 GB.

Table 20. Video

Feature Specification

Integrated Intel HD Graphics 530 / 510

Discrete PCI Express x16 graphics adapter

Specifications 40

Table 21. Audio

Feature Specification

Integrated Realtek HDA Codec ALC3234

Table 22. Network

Feature Specification

Integrated Realtek RTL8111HSD-CG Gigabit Ethernet LAN 10/100/1000 Mb/s

controller

Table 23. System information

Feature Specification

System chipset Intel H110

DMA channels Two 8237 DMA controllers with seven independently programmable

channels

Interrupt levels Integrated I/O APIC capability with 24 interrupts

BIOS chip (NVRAM) 16 MB

Table 24. Expansion bus

Feature Specification

Bus type PCIe gen3 (x16), USB 2.0, and USB 3.0

Bus speed PCI Express:

• x1 -slot each direction speed – up to 985 MB/s

• x16-slot each direction speed–16 GB/s

SATA: 1.5 Gbps, 3.0 Gbps, and 6 Gbps

Table 25. Cards

Feature Specification

PCI express x1 Half height card

PCI express x16 Half height card

Table 26. Drives

Feature Specification

Externally accessible (5.25-inch drive bays) Two

Optical drive One

Specifications 41

Table 27. External connectors

Feature Specification

Audio

Front panel Universal Audio Jack

Back panel Line out connector

Network adapter RJ-45 connector

Serial 9-pin connector; 16550 C compatible (optional)

Parallel 25-pin connector (optional)

USB 2.0 • Front panel: two

• Back panel: two

USB 3.0 • Front panel: two

• Back panel: two

Video • 19-pin HDMI connector

• 20-pin DisplayPort connector

• 15-pin VGA connector (optional)

NOTE: Available video connectors may vary based on the

graphics card selected.

Keyboard and mouse Back panel:

• PS2 Keyboard 6-pin connector (optional)

• PS2 Mouse 6-pin connector (optional)

Table 28. Internal connectors

Feature Specification

PCI Express x16 data width (maximum) — 16 PCI

Express lanes

164-pin connector

Serial ATA Two 7-pin connectors

Memory Two 240-pin connectors

Internal USB 10-pin connector

System fan 4-pin connector

Front panel control 5-pin connector

Processor 1151-pin connector

Processor fan 4-pin connector

Service mode jumper 2-pin connector

Password clear jumper 2-pin connector

RTC reset jumper 2-pin connector

Internal speaker 4-pin connector

Intruder connector 3-pin connector

Specifications 42

Feature Specification

Power connector One 8-pin for PSU, one 4-pin for CPU, one 6-pin for SATA power

Table 29. Controls and lights

Feature Specification

Front of the computer

Power button light White light — Solid white light indicates power-on state; slow

blinking white light indicates sleep state of the computer.

Drive activity light White light — Slow blinking white light indicates that the computer is

reading data from or writing data to the hard drive.

Back of the computer

Link integrity light on integrated network adapter • Green — a 10 Mbps connection exists between the network and

the computer.

• Green — a 100 Mbps connection exists between the network and

the computer.

• Orange — a 1000 Mbps connection exists between the network

and the computer.

• Off (no light) — the computer is not detecting a physical

connection to the network.

Network activity light on integrated network

adapter

Yellow light — A blinking yellow light indicates that network activity

is present.

Power supply diagnostic light Green light — The power supply is turned on and is functional. The

power cable must be connected to the power connector (at the

back of the computer) and the electrical outlet.

Table 30. Power

NOTE: Heat dissipation is calculated by using the power supply wattage rating.

Power Wattage Maximum Heat Dissipation Voltage

180 W 614 BTU/hr 100 V AC to 240 V AC, 50 Hz

to 60 Hz, 3A/1.5A

Coin cell battery 3 V CR2032 lithium coin cell

Table 31. Physical dimension

Feature Specifications

Height 290.00 mm (11.42 inches)

Width 93.00 mm (3.66 inches)

Depth 312.00 mm (8.38 inches)

Weight 6.00 kg (13.22 lb)

Specifications 43

Table 32. Environmental

Feature Specification

Temperature range

Operating 5°C to 35°C (41°F to 95°F)

Storage –40°C to 65°C (–40°F to 149°F)

Relative humidity (maximum)

Operating 20 percent to 80 percent (non-condensing)

Storage 5 percent to 95 percent (non-condensing)

Maximum vibration

Operating 0.26 Grms

Storage 2.20 Grms

Maximum shock

Operating 40 G

Storage 105 G

Altitude

Operating –15.2 m to 3048 m (–50 to 10,000 ft)

Storage –15.20 m to 10,668 m (–50 ft to 35,000 ft)

Airborne contaminant level G1 or lower as defined by ANSI/ISA-S71.04-1985

Specifications 44

Contacting Dell

NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice,

packing slip, bill, or Dell product catalog.

Dell provides several online and telephone-based support and service options. Availability varies by country and product, and

some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues:

1 Go to Dell.com/support.

2 Select your support category.

3 Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.

4 Select the appropriate service or support link based on your need.

Contacting Dell 45

Table of Contents

DELL 3046 User Manual

Related Manuals