DELL 3052 User Manual

Displayed below is the user manual for 3052 by DELL which is a product in the All-in-One PCs/Workstations category. This manual has pages.

Related Manuals

DELL 3052 Manual

DELL 20 3052 Manual

DELL 3052 Manual

Dell Vostro 20–3052

Owner's Manual

Regulatory Model: W15B

Regulatory Type: W15B002

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other

jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.

2015 - 07

Rev. A00

Working on Your Computer

Before Working Inside Your Computer

Use the following safety guidelines to help protect your computer from potential damage and to help to

ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes

that the following conditions exist:

• You have read the safety information that shipped with your computer.

• A component can be replaced or--if purchased separately--installed by performing the removal

procedure in reverse order.

WARNING: Disconnect all power sources before opening the computer cover or panels. After you

finish working inside the computer, replace all covers, panels, and screws before connecting to

the power source.

WARNING: Before working inside your computer, read the safety information that shipped with

your computer. For additional safety best practices information, see the Regulatory Compliance

Homepage at www.dell.com/regulatory_compliance

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or

by periodically touching an unpainted metal surface, such as a connector on the back of the

computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts

on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a

processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable

itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable,

press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep

them evenly aligned to avoid bending any connector pins. Also, before you connect a cable,

ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear differently than shown in

this document.

To avoid damaging your computer, perform the following steps before you begin working inside the

computer.

1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

2. Turn off your computer (see Turning Off Your Computer).

CAUTION: To disconnect a network cable, first unplug the cable from your computer and

then unplug the cable from the network device.

3. Disconnect all network cables from the computer.

4. Disconnect your computer and all attached devices from their electrical outlets.

5. Press and hold the power button while the computer is unplugged to ground the system board.

6. Remove the cover.

CAUTION: Before touching anything inside your computer, ground yourself by touching an

unpainted metal surface, such as the metal at the back of the computer. While you work,

periodically touch an unpainted metal surface to dissipate static electricity, which could

harm internal components.

Recommended Tools

The procedures in this document may require the following tools:

• Small flat-blade screwdriver

• Phillips screwdriver

• Small plastic scribe

Turning Off Your Computer

CAUTION: To avoid losing data, save and close all open files and exit all open programs before

you turn off your computer.

1. Shut down the operating system:

• In Windows 8:

– Using a touch-enabled device:

a. Swipe in from the right edge of the screen, opening the Charms menu and select

Settings.

b. Select the and then select Shut down

– Using a mouse:

a. Point to upper-right corner of the screen and click Settings.

b. Click the and select Shut down.

• In Windows 7:

1. Click Start .

2. Click Shut Down.

1. Click Start .

2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click

Shut Down..

2. Ensure that the computer and all attached devices are turned off. If your computer and attached

devices did not automatically turn off when you shut down your operating system, press and hold

the power button for about 6 seconds to turn them off.

After Working Inside Your Computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and

cables before turning on your computer.

1. Replace the cover.

CAUTION: To connect a network cable, first plug the cable into the network device and then

plug it into the computer.

2. Connect any telephone or network cables to your computer.

3. Connect your computer and all attached devices to their electrical outlets.

4. Turn on your computer.

5. If required, verify that the computer works correctly by running the Dell Diagnostics.

Removing and Installing Components

This section provides detailed information on how to remove or install the components from your

computer.

Removing the Stand

1. Follow the procedures in Before Working Inside Your Computer.

2. Place the computer on a flat surface, display facing downwards.

3. Pry and remove the hinge cover from the computer.

4. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the stand to the computer [1].

b. Slide the stand from the computer [2].

5. Remove the stand from the computer.

Installing the Stand

1. Align the stand on the computer, and tighten the screws to secure the stand to the computer.

2. Place and press the hinge cover on the computer until it clicks into place.

3. Follow the procedures in After Working Inside Your Computer.

Removing the Optical-disk Drive

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the stand.

3. Perform the following steps as shown in the illustration:

a. Press on the tab indicated using a scribe [1].

b. Slide the optical-disk drive (ODD) out of the computer [2].

4. Remove the screws that secure the optical-disk drive bracket, and remove it from the optical drive

[1,2].

Installing the Optical-disk Drive

1. Tighten the screws to secure the optical-disk drive bracket to the optical drive.

2. Insert the optical-disk drive into its slot until it clicks into place.

3. Install:

a. stand

4. Follow the procedures in After Working Inside Your Computer.

Removing the Back Cover

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. stand

b. optical-disk drive

3. Perform the following steps as shown in the illustration:

a. Pry the edge of the base cover [1].

b. Remove the back cover from the computer [2].

Installing the Back Cover

1. Align and press the back cover, until it clicks into place.

2. Install:

a. optical-disk drive

b. stand

3. Follow the procedures in After Working Inside Your Computer.

Removing the Hard Drive

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. stand

b. optical-disk drive

c. back cover

3. Perform the following steps as shown in the illustration:

a. Disconnect the hard-drive cable from the computer [1].

b. Remove the screw that secures the hard-drive to the computer [2].

c. Slide the hard-drive [3].

4. Remove the hard-drive from the computer.

5. Remove the screws that secure the hard-drive to the bracket, lift the hard-drive from bracket [1,2]

Installing the Hard Drive

1. Place the hard-drive in the bracket.

2. Tighten the screws that secure the hard-drive to the bracket.

3. Slide the hard-drive into the screw holes of the display bracket.

4. Tighten the screw that secures the hard-drive to the computer.

5. Connect the hard-drive cable.

6. Install:

a. back cover

b. optical-disk drive

c. stand

7. Follow the procedures in After Working Inside Your Computer.

Removing the Power-Switch Board

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. stand

b. optical-disk drive

c. back cover

3. Perform the following steps as shown in the illustration:

a. Press the locking tab that secures the power-switch to the computer [1].

b. Lift the power-switch board [2].

c. Lift the lock tab and disconnect the power switch cable from the computer [3.4].

Installing the Power-Switch Board

1. Connect the power-switch cable to the power-switch board. Insert the power-switch board into its

slot on the computer.

2. Install:

a. back cover

b. optical-disk drive

c. stand

3. Follow the procedures in After Working Inside Your Computer.

Removing the System-Board Shield

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. stand

b. optical-disk drive

c. back cover

3. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the system-board shield to the computer [1].

b. Lift the system-board shield from the computer [2].

c. Remove the system-board shield from the computer [3].

Installing the System-Board Shield

1. Align the system-board shield on the system board. Tighten the screws to secure it to the computer.

2. Install:

a. back cover

b. optical-disk drive

c. stand

3. Follow the procedures in After Working Inside Your Computer.

Removing the Memory

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. stand

b. optical-disk drive

c. back cover

d. system-board shield

3. Pry the retention clips away from the memory module until it pops-up. Lift and remove the memory

module from its connector.

Installing the Memory

NOTE: Please use DIMM 2 slot if there is only one memory module available.

1. Align the notch on the memory-card with the tab on the system-board connector.

2. Press down on the memory module until the release tabs spring back to secure them in place.

3. Install:

a. system-board shield

b. back cover

c. optical-disk drive

d. stand

4. Follow the procedures in After Working Inside Your Computer.

Removing the System Fan

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. stand

b. optical-disk drive

c. back cover

d. system-board shield

3. Perform the following steps as shown in the illustration:

a. Disconnect the system fan cable from the system board [1].

b. Remove the screws that secure the system fan to the computer [2].

4. Remove the system fan from the computer.

Installing the System Fan

1. Align the system fan with the heatsink such that pins of the bracket are in line with the holes of the

system fan and tighten the screws to secure it to the computer.

2. Connect the system-fan cable to the system board.

3. Install:

a. system-board shield

b. back cover

c. optical-disk drive

d. stand

4. Follow the procedures in After Working Inside Your Computer.

Removing the Heatsink Assembly

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. stand

b. optical-disk drive

c. back cover

d. system-board shield

3. Remove the screws that secure the heatsink assembly to the system board [1,2,3,4,5,6].

4. Remove the heatsink assembly from the system board.

Installing the Heatsink Assembly

1. Install the heatsink assembly and tighten the screws to secure it to the system board.

2. Install:

a. system-board shield

b. back cover

c. optical-disk drive

d. stand

3. Follow the procedures in After Working Inside Your Computer.

Removing the Coin-Cell Battery

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. stand

b. optical-disk drive

c. back cover

d. system-board shield

3. Press the release latch away from the battery and remove the coin-cell battery from the computer

[1,2].

Installing the Coin-Cell Battery

1. Insert the coin-cell battery and press to lock it.

2. Install:

a. system-board shield

b. back cover

c. optical-disk drive

d. stand

3. Follow the procedures in After Working Inside Your Computer.

Removing the WLAN Card

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. stand

b. optical-disk drive

c. back cover

d. system-board shield

3. Perform the following steps as shown in the illustration:

a. Remove the screw that secures the WLAN card and slide to remove the WLAN holder from the

system board [1,2].

b. Remove the two connectors that secure the WLAN card to the system board [3].

c. Remove the WLAN card from its socket [4].

Installing the WLAN Card

1. Insert the WLAN card into its slot.

2. Connect the two connectors (black cable to the black triangle and white cable to the white triangle).

3. Place the WLAN holder and tightened the screw that secures the WLAN card to the system board.

4. Install:

a. stand

b. optical-disk drive

c. back cover

d. system-board shield

5. Follow the procedures in After Working Inside Your Computer.

Removing the Speakers

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. stand

b. optical-disk drive

c. back cover

d. system-board shield

3. Perform the following steps as shown in the illustration:

a. Disconnect the speaker cable [1].

b. Unroute the speaker cable [2].

c. Lift the speaker from the computer chassis [3].

4. Remove the speaker from the computer.

Installing the Speakers

1. Align the speakers on the computer.

2. Align the speaker cables through their tabs on the computer and connect the speaker cable to the

system board.

3. Install:

a. system-board shield

b. back cover

c. optical-disk drive

d. stand

4. Follow the procedures in After Working Inside Your Computer.

System Board Layout

The following image displays the system board layout of the computer.

1. Processor 2. WLAN connector

3. Reserved 4. Webcam connector

5. TXE header 6. Password header

7. CMOS clear header 8. SD Card connector

9. USB 3.0 port 10. USB 3.0 port

11. Universal Jack connector 12. SIO IC

13. Speaker connector 14. Coin Cell Battery

15. Rear USB 2.0 Port 16. Rear USB 2.0 Port

17. Network connector 18. DC IN connector

19. Touch connector 20. Power switch connector

21. Converter connector 22. Audio Jack connector

23. Reserved 24. LVDS connector

25. AMD GPU Mars_LE 26. HDD port

27. Memory socket 28. HDD/ODD port

29. HDD Power connector 30. System fan connector

Removing the System Board

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. stand

b. optical-disk drive

c. back cover

d. system-board shield

e. heatsink

f. WLAN card

g. memory (optional)

3. Disconnect the following from the system board [1,2,3]:

a. display assembly cable

b. system-fan cable

c. hard-drive cable

d. hard-drive/optical-drive power cable

e. power-switch cable

f. speaker cable

g. camera cable

h. convertor cable

4. Remove the screws that secure the system board to the computer. Slide and remove the system

board to release it from the computer [1,2,3].

Installing the System Board

1. Align the system board on the computer.

2. Tighten the screws to secure the system board to the computer.

3. Connect the following cables to the system board:

a. camera cable

b. display assembly cable

c. system fan cable

d. hard-drive cable

e. hard-drive/optical-drive power cable

f. power-switch cable

g. speaker cable

h. convertor cable

4. Install:

a. memory (optional)

b. WLAN card

c. heatsink

d. system-board shield

e. back cover

f. optical-disk drive

g. stand

5. Follow the procedures in After Working Inside Your Computer.

Removing the Display Assembly

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. stand

b. optical-disk drive

c. back cover

d. system-board shield

e. hard drive

f. speakers

g. heatsink

h. system fan

i. memory

j. WLAN card

k. system board

3. Perform the following steps as shown in the illustration:

a. Disconnect convertor cable [1].

b. Unroute the cable [2].

4. Perform the following steps as shown in the illustration:

a. Peel the power cable tape that secures the display assembly cable [1].

b. Unroute the WLAN and camera cables [2].

5. Remove the screws that secure the display bracket to the computer. Lift the display bracket.

6. Pry the edges of the display assembly from the computer.

7. Remove the display assembly from the computer.

Installing the Display Assembly

1. Align and press the display bracket on the computer.

2. Tighten the screws to secure the display bracket to the computer.

3. Align the display assembly cable through the tabs on the display bracket.

4. Install:

a. system board

b. memory

c. WLAN card

d. system fan

e. heatsink

f. speakers

g. system-board shield

h. hard drive

i. optical-disk drive

j. back cover

k. stand

5. Follow the procedures in After Working Inside Your Computer.

System Setup

System Setup enables you to manage your computer hardware and specify BIOS‐level options. From the

System Setup, you can:

• Change the NVRAM settings after you add or remove hardware

• View the system hardware configuration

• Enable or disable integrated devices

• Set performance and power management thresholds

• Manage your computer security

Boot Sequence

Boot Sequence allows you to bypass the System Setup‐defined boot device order and boot directly to a

specific device (for example: optical drive or hard drive). During the Power-on Self Test (POST), when the

Dell logo appears, you can:

• Access System Setup by pressing <F2> key

• Bring up the one-time boot menu by pressing <F12> key

The one-time boot menu displays the devices that you can boot from including the diagnostic option.

The boot-menu options are:

• Removable Drive (if available)

• STXXXX Drive

NOTE: XXX denotes the SATA drive number.

• Optical Drive

• Diagnostics

NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.

The boot sequence screen also displays the option to access the System Setup screen.

Navigation Keys

The following table displays the system setup navigation keys.

NOTE: For most of the system setup options, changes that you make are recorded but do not take

effect until you re-start the system.

Table 1. Navigation Keys

Keys Navigation

Up arrow Moves to the previous field.

Down arrow Moves to the next field.

<Enter> Allows you to select a value in the selected field (if applicable) or follow the link in

the field.

Spacebar Expands or collapses a drop‐down list, if applicable.

<Tab> Moves to the next focus area.

NOTE: For the standard graphics browser only.

<Esc> Moves to the previous page till you view the main screen. Pressing <Esc> in the main

screen displays a message that prompts you to save any unsaved changes and

restarts the system.

<F1> Displays the System Setup help file.

Setup Utility Options

Main

The Main tab lists out the primary hardware features of the computer. The table below defines the

function of each option.

System Time Resets the time on the

computer's internal

clock.

System Date Resets the date on the

computer's internal

calendar.

BIOS Version Displays the BIOS

revision.

Product Name Displays the computer

model number.

Service Tag Displays the Service Tag

of your computer.

Asset Tag Displays the asset tag of

your computer.

CPU Type Displays the processor

model number.

CPU Speed Displays the processor

speed.

CPU ID Displays the processor

ID.

CPU Cache

L1 Cache Displays the processor

L1 cache size.

L2 Cache Displays the processor

L2 cache size.

Fixed HDD Displays the HDD ID and

capacity.

SATA ODD Displays the type of

ODD.

AC Adapter Type Displays the power

adapter type.

System Memory Displays the memory

capacity and type.

Extended Memory Displays the extended

memory capacity

Memory Speed Displays the memory

speed.

Advanced

The Advanced tab allows you to set various functions that affect the performance of the computer. The

table below defines the function of each option and its default value.

Power Now - Enable Allows you to

enable or disable

the Power Now-

Enable.

Default: Enabled

Virtualization Allows you to

enable or disable

the Virtualization.

Default: Enabled

Integrated NIC Allows you to

enable or disable

the Integrated NIC.

Default: Enabled

SATA Operation Allows you to

choose the SATA

operation mode.

Default: AHCI

Adapter Warnings Allows you to

enable or disable

the Adapter

Warnings.

Default: Enabled

Microphone Allows you to

enable or disable

the Microphone.

Default: Enabled

Camera Allows you to

enable or disable

the Camera mode.

Default: Enabled

Internal Bluetooth Allows you to

enable or disable

the Internal

Bluetooth.

Default: Enabled

Internal WLAN Allows you to

enable or disable

the Internal WLAN

Default: Enabled

Media Card Reader Allows you to

enable or disable

the Media Card

Reader

Default: Enabled

Optical Device Allows you to

enable or disable

the Optical Device

Default: Enabled

Boot Disable Allows you to

enable or disable

the Boot Disable

Default: Disabled

USB Configuration

Rear USB Ports Allows you to

enable or disable

the rear USB ports.

Default: Enabled

Side USB Ports Allows you to

enable or disable

the side USB ports.

Default: Enabled

USB debug Allows you to

enable or disable

the USB debug

Default: Disabled

Power Options

Wake Up By Integrated LAN/WLAN Allows the

computer to be

remotely turned

on.

Default: Disabled

AC Recovery Allows you to

select the power

state of the

computer after an

AC power loss.

Default: Power Off

Deep Sleep Control Allows you to

select the Deep

Sleep Control

Default: Enabled in

S4 and S5

Auto Power On Enable or disable

the Auto Power

On.

Default: Disabled

Auto Power On Mode Allows you to

control the power

mode

Auto Power On Date Allows you to

designate a specific

date when the

computer will turn

on automatically

Default: Disabled

Auto Power On Time Allows you to

designate a specific

time when the

computer will turn

on automatically

Default: Disabled

SMART Settings

SMART Self Test Enable or disable

the SMART Self

Test

Default: Disabled

Security

The Security tab displays the security status and allows you to manage the security features of the

computer.

Unlock Setup Status Allows you to enable an Unlock Setup Status (Default: Unlocked)

Admin Password Status Allows you to set, change or delete the administrator (admin)

password status.

System Password Status Allows you to set, change or delete the system password status.

HDD Passwords Status Allows you to set, change or delete the password on the system

hard-disk drive.

Asset Tag

Admin Password Allows you to set, change or delete the administrator (admin)

password.

System Password Allows you to set, change or delete the system password.

HDD Passwords Allows you to set, change or delete the password on the system

hard-disk drive.

Password Change Allows you to enable the disable permission to the System and

Hard Drive passwords when the admin password is set.

Password Bypass Allows you to enable or disable the permission to bypass the

System when they are set

Secure Boot Mode This option enables or disables the Secure Boot Feature.

Key Management

Default Key Provisioning This option enables or disables the Default Key Provisioning

(Default: Disabled)

Install Default Secure Boot keys Allows you to enables you to Install Factory Secure Variables.

Save All Secure Boot Variables Allows you to Save All Secure Boot Variables.

Platform Key (PK)

Delete the PK Allows you to Delete the PK.

Set PK from Files Allows you to Set PK from Files from Factory Default.

Key Exchange Key Database

(KEK)

Delete the KEY Allows you to Delete the KEK.

Set KEK from Files Allows you to Set KEY from Files from Factory Default.

Append an entry to KEK Allows you to Append KEK key from Factory Default.

Authorized Signature Database

(DB)

Delete the DB Allows you to Delete the DB.

Set DB from Files Allows you to Set DB from Files from Factory Default.

Append an entry to DB Allows you to Append DB key from Factory Default.

Authorized TimeStamps

Delete the DBT Allows you to Delete the DBT.

Set DBT from Files Allows you to Set DBT from Files from Factory Default.

Append an entry to DBT Allows you to Append DBT key from Factory Default.

HDD Protection This option enables or disables the HDD Protection (Default:

Disabled)

HDD Recovery This option enables or disables the HDD Recovery (Default:

Enabled)

Boot

The Boot tab allows you to change the boot sequence.

Boot List Option Allows you to change

the order in which the

computer attempts to

find an operating

system.

Default: UEFI

File Browser Add Boot Option Allows you to Add file

browser boot option.

File Browser Delete Boot Option Allows you to Delete file

browser boot option.

Secure Boot Enable or disable the

Secure Boot Control.

Default: Enabled

Load Legacy Option ROM This option control

whether CSM should be

loaded during POST.

Default: Disabled

Boot Option Priorities

Boot Option 1 Allows you to select the

1st boot device

preference

Boot Option 2 Allows you to select the

2nd boot device

preference

Boot Option 3 Allows you to select the

3rd boot device

preference

Exit

This section allows you to save, discard and load default settings before exiting from Setup Utility.

Save Changes and Reset Allows you to Save Changes and Reset default setting before

exiting from Setup Utility.

Discard Changes and Reset Allows you to Discard Changes and Reset default setting

before exiting from Setup Utility.

Restore Defaults Allows you to Restore Default setting before exiting from

Setup Utility.

Discard Changes Allows you to Discard Changes setting before exiting from

Setup Utility.

Save Changes Allows you to Save Changes setting before exiting from Setup

Utility.

Updating the BIOS

It is recommended to update your BIOS (system setup), on replacing the system board or if an update is

available. For laptops, ensure that your computer battery is fully charged and connected to a power

outlet

1. Re-start the computer.

2. Go to dell.com/support.

3. Enter the Service Tag or Express Service Code and click Submit.

NOTE: To locate the Service Tag, click Where is my Service Tag?

NOTE: If you cannot find your Service Tag, click Detect My Product. Proceed with the

instructions on screen.

4. If you are unable to locate or find the Service Tag, click the Product Category of your computer.

5. Choose the Product Type from the list.

6. Select your computer model and the Product Support page of your computer appears.

7. Click Get drivers and click View All Drivers.

The Drivers and Downloads page opens.

8. On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS.

9. Identify the latest BIOS file and click Download File.

You can also analyze which drivers need an update. To do this for your product, click Analyze

System for Updates and follow the instructions on the screen.

10. Select your preferred download method in the Please select your download method below window,

click Download File.

The File Download window appears.

11. Click Save to save the file on your computer.

12. Click Run to install the updated BIOS settings on your computer.

Follow the instructions on the screen.

System and Setup Password

You can create a system password and a setup password to secure your computer.

Password Type Description

System password Password that you must enter to log on to your system.

Setup password Password that you must enter to access and make changes to the BIOS settings of

your computer.

CAUTION: The password features provide a basic level of security for the data on your computer.

CAUTION: Anyone can access the data stored on your computer if it is not locked and left

unattended.

NOTE: Your computer is shipped with the system and setup password feature disabled.

Assigning a System Password and Setup Password

You can assign a new System Password and/or Setup Password or change an existing System Password

and/or Setup Password only when Password Status is Unlocked. If the Password Status is Locked, you

cannot change the System Password.

NOTE: If the password jumper is disabled, the existing System Password and Setup Password are

deleted and you need not provide the system password to log on to the computer.

To enter a system setup, press <F2> immediately after a power-on or re-boot.

1. In the System BIOS or System Setup screen, select System Security and press <Enter>.

The System Security screen appears.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password , enter your system password, and press <Enter> or <Tab>.

Use the following guidelines to assign the system password:

• A password can have up to 32 characters.

• The password can contain the numbers 0 through 9.

• Only lower case letters are valid, upper case letters are not allowed.

• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

Re-enter the system password when prompted.

4. Type the system password that you entered earlier and click OK.

5. Select Setup Password, type your system password and press <Enter> or <Tab>.

A message prompts you to re-type the setup password.

6. Type the setup password that you entered earlier and click OK.

7. Press <Esc> and a message prompts you to save the changes.

8. Press <Y> to save the changes.

The computer reboots.

Deleting or Changing an Existing System and/or Setup Password

Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change

the existing System and/or Setup password. You cannot delete or change an existing System or Setup

password, if the Password Status is Locked.

To enter the System Setup, press <F2> immediately after a power-on or reboot.

1. In the System BIOS or System Setup screen, select System Security and press <Enter>.

The System Security screen is displayed.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password, alter or delete the existing system password and press <Enter> or <Tab>.

4. Select Setup Password, alter or delete the existing setup password and press <Enter> or <Tab>.

NOTE: If you change the System and/or Setup password, re-enter the new password when

promoted. If you delete the System and/or Setup password, confirm the deletion when

promoted.

5. Press <Esc> and a message prompts you to save the changes.

6. Press <Y> to save the changes and exit from the System Setup.

The computer reboots.

Technical Specifications

NOTE: Offerings may vary by region. The following specifications are only those required by law to

ship with your computer. For more information about the configuration of your computer, go to

Help and Support in your Windows operating system and select the option to view information

about your computer.

Table 2. System Information

Feature Specification

Processor type 2 MB cache

Total cache Up to 4 MB cache depending on processor type

Table 3. Memory

Feature Specification

Type up to 1600 MHz

Connectors one DIMM slots

Capacity 2 GB, 4 GB, and 8 GB

Minimum Memory 2 GB

Maximum Memory 8 GB

Table 4. Video

Feature Specification

Video Controller:

Integrated SoC

Discrete Radeon R5 A315

Video Memory 2 GB

Table 5. Audio

Feature Specification

Controller ALC3661-CG (Realtek)

Speaker single 4-ohms, 2.5 W AVG speakers

Internal speaker amplifier up to 3 W per channel

Internal microphone support single digital microphone

Feature Specification

Volume controls Volume up/down buttons, program menus, and keyboard

media-control keys

Table 6. Communications

Feature Specification

Network adapter Intel 10/100/1000 Mbps Ethernet LAN

Table 7. Displays

Feature Specification

Type 19.5 inch HD+

Maximum resolution 1600 x 900

Refresh rate 60 Hz

Brightness 250nits

Operating angle 170 horizontal / 160 vertical

Pixel pitch 0.2712 mm x 0.2626 mm

Table 8. Drives

Feature Specification

Hard drive one 2.5-inch SATA drive

Optical drive (optional) one DVD RW

Table 9. Ports and Connectors

Feature Specification

Audio one audio combo connector

Network adapter one RJ45 connector

USB 2.0 two

USB 3.0 two

Media card reader one 4-in-1 slot

Table 10. Power Adapter

Feature Specification

Type 45 W (UMA) 65W (Discrete)

Frequency 50 Hz - 60 Hz

Voltage 100 VAC - 240 VAC

Input current: Maximum 1.7 A Maximum 2.5 A

Adapter Physical Dimensions:

Feature Specification

Height 26.00 mm (1.02 inches) 32.00 mm (1.3 inches)

Width 40.00 mm (1.57 inches) 52.00 mm (2.0 inches)

Depth 94.00 mm (3.70 inches) 128.00 mm (5.0 inches)

Coin-cell battery 3 V CR2032 lithium coin cell

Table 11. Camera

Feature Specification

Image resolution 2.0 Megapixel

Video resolution HD / 720P / 0.92 Megapixels (1280 x 720 pixels)

Diagonal viewing angle 74 degrees

Table 12. Stand

Feature Specification

Tilt –5 degrees to 30 degrees

Table 13. Physical Dimensions

Feature Without Stand With Stand

Width 480.52 mm (18.91 inches) 480.52 mm (18.91 inches)

Height 317.64 mm (12.50 inches) 387.11 mm (15.24 inches)

Depth: 69.47 mm (2.73 inches) 204.98 mm (8.07 inches)

Weight: 3.42 kg (7.53 lb) 4.92 kg ( 10.84 lb)

NOTE: The weight of your computer may vary depending on the configuration ordered and the

manufacturing variability. The above weight is without an optical-disk drive.

Table 14. Controls and Lights

Feature Specification

Power button light White light — Solid white light indicates power-on state;

blinking white light indicates sleep state of the computer.

Hard Drive activity light White light — Blinking white light indicates that the computer

is reading data from or writing data to the hard drive.

Camera LED White light — solid while light indicates that the camera is on.

Back panel:

Link integrity light on integrated

network adapter :

Green — a good 10 Mbps connection exists between the

network and the computer.

Orange — a good 1000 Mbps connection exists between the

network and the computer.

Feature Specification

Off (no light) — the computer is not detecting a physical

connection to the network.

Network activity light on integrated

network adapter

Yellow light — A blinking yellow light indicates that network

activity is present.

Power supply diagnostic light Green light — The power supply is turned on and is

functional. The power cable must be connected to the

power connector (at the back of the computer) and the

electrical outlet.

Table 15. Environmental

Feature Specification

Temperature range:

Operating 5 °C to 35 °C (41 °F to 95 °F)

Storage –40 °C to 65 °C (–40 °F to 149 °F)

Relative humidity (maximum):

Operating 10% to 90% (non-condensing)

Storage 10% to 95% (non-condensing)

Maximum vibration:

Operating 0.66 GRMS

Storage 1.30 GRMS

Maximum shock:

Operating 110 G

Storage 160 G

Altitude:

Operating –15.2 m to 3048 m (–50 to 10,000 ft)

Storage –15.20 m to 10,668 m (–50 ft to 35,000 ft)

Airborne contaminant level G2 or lower as defined by ANSI/ISA-S71.04-1985

Contacting Dell

NOTE: If you do not have an active Internet connection, you can find contact information on your

purchase invoice, packing slip, bill, or Dell product catalog.

Dell provides several online and telephone-based support and service options. Availability varies by

country and product, and some services may not be available in your area. To contact Dell for sales,

technical support, or customer service issues:

1. Go to support.dell.com.

2. Select your support category.

3. Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the

page.

4. Select the appropriate service or support link based on your need.

Table of Contents

DELL 3052 User Manual

Related Manuals