Table of Contents
- OptiPlex 3080 Tower Service Manual
- Working on your computer
- Technology and components
- Major components of your system
- Disassembly and reassembly
- Side cover
- Front bezel
- Fan duct
- Hard-drive assembly
- 3.5-inch hard drive
- Solid-state drive
- Memory modules
- Processor fan and heat-sink assembly
- Processor
- Graphics card
- Graphical processing unit
- Coin-cell battery
- WLAN card
- Slim optical-drive
- Slim optical-drive bracket
- Speaker
- Power button
- Power-supply unit
- Intrusion switch
- Optional I/O modules (Type C/ HDMI/VGA/DP/Serial)
- System board
- Troubleshooting
- Getting help
DELL 3080 User Manual
Displayed below is the user manual for 3080 by DELL which is a product in the PCs/Workstations category. This manual has pages.
Related Manuals
OptiPlex 3080 Tower
Service Manual
Regulatory Model: D29M
Regulatory Type: D29M002
May 2020
Rev. A00
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid
the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other
trademarks may be trademarks of their respective owners.
Chapter 1: Working on your computer........................................................................................... 6
Safety instructions.............................................................................................................................................................. 6
Before working inside your computer.......................................................................................................................6
Safety precautions.........................................................................................................................................................7
Electrostatic discharge—ESD protection................................................................................................................7
ESD field service kit ..................................................................................................................................................... 8
After working inside your computer..........................................................................................................................9
Chapter 2: Technology and components.......................................................................................10
Graphics options................................................................................................................................................................ 10
Intel UHD 610 Graphics...............................................................................................................................................10
Intel UHD 630 Graphics..............................................................................................................................................10
NVIDIA GeForce GT 730............................................................................................................................................. 11
AMD Radeon RX 640.................................................................................................................................................. 12
AMD Radeon R5 430...................................................................................................................................................13
System management features........................................................................................................................................ 13
Dell Client Command Suite for In-Band systems management ........................................................... 14
Chapter 3: Major components of your system.............................................................................. 15
Chapter 4: Disassembly and reassembly.......................................................................................18
Side cover............................................................................................................................................................................ 18
Removing the side cover............................................................................................................................................18
Installing the side cover............................................................................................................................................. 20
Front bezel...........................................................................................................................................................................21
Removing the front bezel...........................................................................................................................................21
Installing the front bezel............................................................................................................................................ 22
Fan duct...............................................................................................................................................................................23
Removing the fan duct...............................................................................................................................................23
Installing the fan duct.................................................................................................................................................23
Hard-drive assembly......................................................................................................................................................... 24
Removing the 2.5-inch hard-disk drive assembly................................................................................................24
Removing the 2.5-inch hard-disk drive bracket.................................................................................................. 25
Installing the 2.5-inch hard-disk drive bracket.....................................................................................................26
Installing the 2.5-inch hard-disk drive assembly.................................................................................................. 27
3.5-inch hard drive............................................................................................................................................................29
Removing the 3.5 inch hard drive........................................................................................................................... 29
Installing the 3.5 inch hard drive..............................................................................................................................29
Solid-state drive................................................................................................................................................................ 30
Removing the M.2 2230 PCIe solid-state drive................................................................................................... 30
Installing the M.2 2230 PCIe solid-state drive...................................................................................................... 31
Removing the M.2 2280 PCIe solid-state drive................................................................................................... 32
Installing the M.2 2280 PCIe solid-state drive..................................................................................................... 33
Memory modules............................................................................................................................................................... 34
Contents
Contents 3
Removing the memory modules...............................................................................................................................34
Installing the memory modules.................................................................................................................................35
Processor fan and heat-sink assembly.........................................................................................................................36
Removing the processor fan and heat-sink assembly........................................................................................ 36
Installing the processor fan and heat-sink assembly.......................................................................................... 37
Processor............................................................................................................................................................................ 38
Removing the processor............................................................................................................................................38
Installing the processor.............................................................................................................................................. 39
Graphics card...................................................................................................................................................................... 41
Removing the graphics card...................................................................................................................................... 41
Installing the graphics card....................................................................................................................................... 42
Graphical processing unit................................................................................................................................................ 43
Removing the powered GPU.................................................................................................................................... 43
Installing the powered GPU...................................................................................................................................... 43
Coin-cell battery................................................................................................................................................................ 43
Removing the coin-cell battery................................................................................................................................43
Installing the coin-cell battery.................................................................................................................................. 44
WLAN card..........................................................................................................................................................................45
Removing the WLAN card.........................................................................................................................................45
Installing the WLAN card........................................................................................................................................... 46
Slim optical-drive...............................................................................................................................................................48
Removing the Slim-Optical Disk Drive....................................................................................................................48
Installing the Slim-Optical Disk Drive......................................................................................................................48
Slim optical-drive bracket............................................................................................................................................... 49
Removing the slim-ODD bracket............................................................................................................................. 49
Installing the slim-ODD bracket............................................................................................................................... 50
Speaker.................................................................................................................................................................................51
Removing the speaker................................................................................................................................................ 51
Installing the speaker...................................................................................................................................................51
Power button..................................................................................................................................................................... 52
Removing the power button..................................................................................................................................... 52
Installing the power button....................................................................................................................................... 53
Power-supply unit............................................................................................................................................................. 54
Removing the power-supply unit.............................................................................................................................54
Installing the power-supply unit...............................................................................................................................56
Intrusion switch................................................................................................................................................................. 58
Removing the intrusion switch.................................................................................................................................58
Installing the intrusion switch...................................................................................................................................59
Optional I/O modules (Type C/ HDMI/VGA/DP/Serial)........................................................................................ 60
Removing optional I/O modules (Type C/ HDMI/VGA/DP/Serial)................................................................60
Installing optional I/O modules (Type-C/HDMI/VGA/DP/Serial)................................................................... 61
System board..................................................................................................................................................................... 65
Removing the system board.....................................................................................................................................65
Installing the system board....................................................................................................................................... 68
Chapter 5: Troubleshooting......................................................................................................... 72
Dell SupportAssist Pre-boot System Performance Check diagnostics................................................................72
Running the SupportAssist Pre-Boot System Performance Check................................................................ 72
Diagnostic LED behavior..................................................................................................................................................73
Diagnostic error messages.............................................................................................................................................. 74
4Contents
System error messages....................................................................................................................................................77
WiFi power cycle................................................................................................................................................................77
Chapter 6: Getting help............................................................................................................... 79
Contacting Dell...................................................................................................................................................................79
Contents 5
Working on your computer
Topics:
•Safety instructions
Safety instructions
Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless
otherwise noted, each procedure included in this document assumes that you have read the safety information that shipped
with your computer.
NOTE: Before working inside your computer, read the safety information that is shipped with your computer. For more
safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
NOTE: Disconnect your computer from all power sources before opening the computer cover or panels. After you finish
working inside the computer, replace all covers, panels, and screws before connecting your computer to an electrical outlet.
CAUTION: To avoid damaging the computer, ensure that the work surface is flat, dry and clean.
CAUTION: To avoid damaging the components and cards, handle them by their edges, and avoid touching the
pins and the contacts.
CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical
assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the
safety instructions that is shipped with the product or at www.dell.com/regulatory_compliance.
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal
surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal
surface to dissipate static electricity which could harm internal components.
CAUTION: When you disconnect a cable, pull it by its connector or its pull tab, not the cable itself. Some cables
have connectors with locking tabs or thumb-screws that you must disengage before disconnecting the cable.
When disconnecting cables, keep them evenly-aligned to avoid bending the connector pins. When connecting
cables, ensure that the ports and the connectors are correctly oriented and aligned.
CAUTION: Press and eject any installed card from the media-card reader.
NOTE: The color of your computer and certain components may appear differently than shown in this document.
Before working inside your computer
About this task
NOTE: The images in this document may differ from your computer depending on the configuration you ordered.
Steps
1. Save and close all open files and exit all open applications.
2. Shut down your computer. Click Start > Power > Shut down.
1
6 Working on your computer
NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down
instructions.
3. Disconnect your computer and all attached devices from their electrical outlets.
4. Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.
CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the
cable from the network device.
5. Remove any media card and optical disc from your computer, if applicable.
Safety precautions
The safety precautions chapter details the primary steps to be taken before performing any disassembly instructions.
Observe the following safety precautions before you perform any installation or break/fix procedures involving disassembly or
reassembly:
●Turn off the system and all attached peripherals.
●Disconnect the system and all attached peripherals from AC power.
●Disconnect all network cables, telephone, and telecommunications lines from the system.
●Use an ESD field service kit when working inside any desktop to avoid electrostatic discharge (ESD) damage.
●After removing any system component, carefully place the removed component on an anti-static mat.
●Wear shoes with non-conductive rubber soles to reduce the chance of getting electrocuted.
Standby power
Dell products with standby power must be unplugged before you open the case. Systems that incorporate standby power are
essentially powered while turned off. The internal power enables the system to be remotely turned on (wake on LAN) and
suspended into a sleep mode and has other advanced power management features.
Unplugging, pressing and holding the power button for 15 seconds should discharge residual power in the system board.
Bonding
Bonding is a method for connecting two or more grounding conductors to the same electrical potential. This is done through the
use of a field service electrostatic discharge (ESD) kit. When connecting a bonding wire, ensure that it is connected to bare
metal and never to a painted or non-metal surface. The wrist strap should be secure and in full contact with your skin, and
ensure that you remove all jewelry such as watches, bracelets, or rings prior to bonding yourself and the equipment.
Electrostatic discharge—ESD protection
ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards,
processors, memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such
as intermittent problems or a shortened product life span. As the industry pushes for lower power requirements and increased
density, ESD protection is an increasing concern.
Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than
in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.
Two recognized types of ESD damage are catastrophic and intermittent failures.
●Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes an
immediate and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has received
a static shock and immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or
nonfunctional memory.
●Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of
intermittent failures means that most of the time when damage occurs, it is not immediately recognizable. The DIMM
receives a static shock, but the tracing is merely weakened and does not immediately produce outward symptoms related to
the damage. The weakened trace may take weeks or months to melt, and in the meantime may cause degradation of memory
integrity, intermittent memory errors, etc.
Working on your computer 7
The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded")
failure.
Perform the following steps to prevent ESD damage:
●Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do
not provide adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on
parts with increased sensitivity to ESD damage.
●Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.
●When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static
packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you
discharge static electricity from your body.
●Before transporting a static-sensitive component, place it in an anti-static container or packaging.
ESD field service kit
The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components:
anti-static mat, wrist strap, and bonding wire.
Components of an ESD field service kit
The components of an ESD field service kit are:
●Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an
anti-static mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal
on the system being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly
on the mat. ESD-sensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.
●Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist
and bare metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that
is temporarily placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD
mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never use
wireless wrist straps. Always be aware that the internal wires of a wrist strap are prone to damage from normal wear and
tear, and must be checked regularly with a wrist strap tester in order to avoid accidental ESD hardware damage. It is
recommended to test the wrist strap and bonding wire at least once per week.
●ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored
kit, it is a best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A wrist
strap tester is the best method for doing this test. If you do not have your own wrist strap tester, check with your regional
office to find out if they have one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is
strapped to your wrist and push the button to test. A green LED is lit if the test is successful; a red LED is lit and an alarm
sounds if the test fails.
●Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts
that are insulators and often highly charged.
●Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For
example, deploying the kit for a server environment is different than for a desktop or portable environment. Servers are
typically installed in a rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always
look for a large open flat work area that is free of clutter and large enough to deploy the ESD kit with additional space to
accommodate the type of system that is being repaired. The workspace should also be free of insulators that can cause an
ESD event. On the work area, insulators such as Styrofoam and other plastics should always be moved at least 12 inches or
30 centimeters away from sensitive parts before physically handling any hardware components
●ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded
bags are preferred. However, you should always return the damaged part using the same ESD bag and packaging that the
new part arrived in. The ESD bag should be folded over and taped shut and all the same foam packing material should be
used in the original box that the new part arrived in. ESD-sensitive devices should be removed from packaging only at an
ESD-protected work surface, and parts should never be placed on top of the ESD bag because only the inside of the bag is
shielded. Always place parts in your hand, on the ESD mat, in the system, or inside an anti-static bag.
●Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts
to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.
8Working on your computer
ESD protection summary
It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static
mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all
insulator parts while performing service and that they use anti-static bags for transporting sensitive components.
After working inside your computer
About this task
CAUTION: Leaving stray or loose screws inside your computer may severely damage your computer.
Steps
1. Replace all screws and ensure that no stray screws remain inside your computer.
2. Connect any external devices, peripherals, or cables you removed before working on your computer.
3. Replace any media cards, discs, or any other parts that you removed before working on your computer.
4. Connect your computer and all attached devices to their electrical outlets.
5. Turn on your computer.
Working on your computer 9
Technology and components
This chapter details the technology and components available in the system.
Topics:
•Graphics options
•System management features
Graphics options
Intel UHD 610 Graphics
Table 1. Intel UHD 610 Graphics specifications
Intel UHD 610 Graphics
Bus Type Integrated
Memory Type UMA
Graphics Level Celeron/Pentium Gold: GT2 (UHD)
Overlay Planes Yes
Operating Systems Graphics/ Video API Support DirectX 12, OpenGL (4.5 from Intel CML POR)
Supports maximum resolution ●DP: 4096 x 2304 @60 Hz, 24 bpp
●Option DP: 4096 x 2304 @60 Hz
●Option USB type-C Alt mode: 4096 x 2304 @60 Hz
●Option VGA: 1920 x 1200 @60 Hz
●Option HDMI2.0: 4096 x 2160 @60 Hz
Number of display supported Up to three displays supported
Multiple Display Support ●Two motherboard integrated DP1.4 HBR2 + One video
option (VGA/DP1.4 HBR2/HDMI2.0/USB3.2 Gen2 type-C
Alt-mode)
External Connectors Two MB integrated DP1.4 HBR2 + One video option (VGA/
DP1.4 HBR2/HDMI2.0/USB3.2 Gen2 type-C Alt-mode)
Intel UHD 630 Graphics
Table 2. Intel UHD 630 Graphics specifications
Intel UHD 630 Graphics
Bus Type Integrated
Memory Type UMA
Graphics Level i3/i5: GT2 (UHD)
Overlay Planes Yes
Operating Systems Graphics/ Video API Support DirectX 12, OpenGL (4.5 from Intel CML POR)
2
10 Technology and components
Table 2. Intel UHD 630 Graphics specifications (continued)
Intel UHD 630 Graphics
Supports maximum resolution ●DP: 4096 x 2304 @60 Hz, 24 bpp
●Option DP: 4096 x 2304 @60 Hz
●Option USB type-C Alt mode: 4096 x 2304 @60 Hz
●Option VGA: 1920 x 1200 @60 Hz
●Option HDMI2.0: 4096 x 2160 @60 Hz
Number of display supported Up to three displays supported
Multiple Display Support ●Two motherboard integrated DP1.4 HBR2 + One video
option (VGA/DP1.4 HBR2/HDMI2.0/USB3.2 Gen2 type-C
Alt-mode)
External Connectors Two MB integrated DP1.4 HBR2 + One video option (VGA/
DP1.4 HBR2/HDMI2.0/USB3.2 Gen2 type-C Alt-mode)
NVIDIA GeForce GT 730
Table 3. NVIDIA GeForce GT 730 specifications
Feature Values
GPU frequency 902 MHz
DirectX 12.0
Shader model 5.0
Open CL 1.1
Open GL 4.5
GPU memory interface 64 bit
PCIe bus PCIe 3.0 x8
Display support One DisplayPort 1.2
Graphics memory configuration 2 GB, GDDR5
Graphics memory clock speed 2.5 GHz
Active fan sink 2-pin excluded fan controller
Slot number Single slot
PCB form factor Low profile
PCB layer 4 layer
PCB solder mask Green
Bracket form factor Low profile
Maximum resolution 3840 x 2160
Power consumption u
Technology and components 11
Table 3. NVIDIA GeForce GT 730 specifications (continued)
Feature Values
●20 W TDP
30 W TGP
3D mark performance ●3DMark 11 (P): E4131
●3Dmark Vantage(P):
AMD Radeon RX 640
Table 4. AMD Radeon RX 640 specifications
Feature Values
GPU frequency 1.2 GHz
DirectX 12
Shader model 5.0
Open CL 2.0
Open GL 4.5
GPU memory interface 128 bit
PCIe bus PCIe 3.0 x8
Display support ●Two Mini DisplayPorts
●One DisplayPort
Graphics memory configuration 4 GB, GDDR5
Graphics memory clock speed 7 Gbps
Active fan sink 4-pin embedded fan controller
Slot number Single slot
PCB form factor Low profile
PCB layer 6 layer
PCB solder mask Green
Bracket form factor Low profile
Maximum resolution 5120 x 2880
Power consumption 50 W
3D mark performance 3DMark 11 (P): 5315
12 Technology and components
AMD Radeon R5 430
Table 5. AMD Radeon R5 430 specifications
Feature Values
GPU frequency 780 MHz
DirectX 11.2
Shader model 5.0
Open CL 1.2
Open GL 4.2
GPU memory interface 64 bit
PCIe bus PCIe 3.0 x8
Display support 1 DisplayPort 1.2
Graphics memory configuration 2 GB, GDDR5
Graphics memory clock speed 1.5 GHz
Active fan sink 2-pin excluded fan controller
Slot number Single slot
PCB form factor Low profile
PCB layer 6 layer
PCB solder mask Green
Bracket form factor ●Full height
●Low profile
Maximum resolution 4096 x 2160
Power consumption ●25 W TDP
●35 W TGP
3D mark performance ●3DMark 11 (P)
●3Dmark Vantage(P)
System management features
Dell commercial systems come with a number of systems management options that are included by default for In-Band
management with the Dell Client Command Suite. In-Band management is when the system has a functional operating system
and the device is connected to a network so that it can be managed. The Dell Client Command Suite of tools can be leveraged
individually or with a systems management console like SCCM, LANDESK, KACE, etc.
We also offer Out-of-Band management as an option. Out-of-band management is when the system does not have a functional
operating system or is turned off and you still want to be able to manage the system in that state.
Technology and components 13
Dell Client Command Suite for In-Band systems management
Dell Client Command Suite is a free toolkit available for download, for all Latitude Rugged tablets at dell.com/support,
automates and streamlines systems management tasks, saving time, money, and resources. It consists of the following modules
that can be used independently, or with a variety of systems management consoles such as SCCM.
Dell Client Command Suite's integration with VMware Workspace ONE Powered by AirWatch, now allows customers to manage
their Dell client hardware from the cloud, using a single Workspace ONE console.
Dell Command | Deploy enables easy operating system (OS) deployment across all major OS deployment methodologies and
provides numerous system-specific drivers that have been extracted and reduced to an OS-consumable state.
Dell Command l Configure is a graphical user interface (GUI) admin tool for configuring and deploying hardware settings in a
pre-OS or post-OS environment, and it operates seamlessly with SCCM and Airwatch and can be self-integrated into LANDesk
and KACE. Simply, this is all about the BIOS. Command l Configure allows you to remotely automate and configure over 150+
BIOS settings for a personalized user experience.
Dell Command l PowerShell Provider can do the same things as Command l Configure, but with a different method.
PowerShell is a scripting language that allows customers to create a customized and dynamic configuration process.
Dell Command l Monitor is a Windows Management Instrumentation (WMI) agent that provides IT admins with an extensive
inventory of the hardware and health-state data. Admins can also configure hardware remotely by using command line and
scripting.
Dell Command l Power Manager (end-user tool) is a GUI-based factory-installed battery management tool that allows end
users to choose the battery management methods that meet their personal preferences or work schedule without sacrificing
IT's capability to control those settings with Group Policy.
Dell Command | Update (end-user tool) is factory-installed and allows admins to individually manage and automatically
present and install Dell updates to the BIOS, drivers, and software. Command l Update eliminates the time-consuming hunting
and pecking process of update installation.
Dell Command l Update Catalog provides searchable metadata that allows the management console to retrieve the latest
system-specific updates (driver, firmware or BIOS). The updates are then delivered seamlessly to end-users using the
customer's systems management infrastructure that is consuming the catalog (like SCCM).
Dell Command | vPro Out of Band console extends hardware management to systems that are offline or have an un-
reachable OS (Dell exclusive features).
Dell Command | Integration Suite for System Center - This suite integrates all the key components of the Client Command
Suite into Microsoft System Center Configuration Manager 2012 and Current Branch versions.
14 Technology and components
3
Major components of your system 15
Major components of your system
16 Major components of your system
NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These
parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative for
purchase options.
Major components of your system 17
Disassembly and reassembly
Topics:
•Side cover
•Front bezel
•Fan duct
•Hard-drive assembly
•3.5-inch hard drive
•Solid-state drive
•Memory modules
•Processor fan and heat-sink assembly
•Processor
•Graphics card
•Graphical processing unit
•Coin-cell battery
•WLAN card
•Slim optical-drive
•Slim optical-drive bracket
•Speaker
•Power button
•Power-supply unit
•Intrusion switch
•Optional I/O modules (Type C/ HDMI/VGA/DP/Serial)
•System board
Side cover
Removing the side cover
Prerequisites
1. Follow the procedure in before working inside your computer.
NOTE: Ensure that you remove the security cable from the security-cable slot (if applicable).
About this task
The following images indicate the location of the side cover and provide a visual representation of the removal procedure.
4
18 Disassembly and reassembly
Steps
1. Loosen the thumbscrew (#6-32) that secures the side cover to the computer.
2. Slide the side cover towards the rear of the computer and lift the cover away from the computer.
Disassembly and reassembly 19
Installing the side cover
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the side cover and provides a visual representation of the installation procedure.
20 Disassembly and reassembly
Steps
1. Locate the side cover slot on your computer.
2. Align the tabs on the side cover with the slots on the chassis.
3. Slide the side cover towards the front of the computer to install it.
4. Tighten the thumbscrew (#6-32) to secure the side cover to the computer.
Next steps
1. Follow the procedure in after working inside your computer.
Front bezel
Removing the front bezel
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
About this task
The following images indicate the location of the front bezel and provide a visual representation of the removal procedure.
Steps
1. Pry the retention tabs to release the front bezel from the computer.
Disassembly and reassembly 21
2. Slightly pull the front bezel and gently rotate to release the other tabs on the bezel from the slots in the computer chassis.
3. Remove the front bezel from the computer.
Installing the front bezel
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the front bezel and provides a visual representation of the installation procedure.
Steps
1. Position the front bezel to align the tabs on the bezel with the slots on the chassis.
2. Press the bezel until the tabs clicks into place.
Next steps
1. Install the side cover.
2. Follow the procedure in after working inside your computer.
22 Disassembly and reassembly
Fan duct
Removing the fan duct
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
About this task
The following images indicate the location of the fan duct and provide a visual representation of the removal procedure.
Steps
1. Press the retention tabs on both sides of the fan duct to release it.
2. Pull and remove the fan duct from the computer.
Installing the fan duct
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the fan duct and provides a visual representation of the installation procedure.
Disassembly and reassembly 23
Steps
1. Position the fan duct to align it with the slots on the computer chassis.
2. Press the fan duct until it clicks into place.
Next steps
1. Install the side cover.
2. Follow the procedure in after working inside your computer.
Hard-drive assembly
Removing the 2.5-inch hard-disk drive assembly
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the fan duct.
About this task
The following images indicate the location of the 2.5-inch hard-disk drive assembly and provide a visual representation of the
removal procedure.
24 Disassembly and reassembly
Steps
1. Disconnect the hard-drive data and power cables from the connectors on the 2.5-inch hard-disk drive module.
2. Press the release tabs on both the sides of the hard-disk drive bracket to release it from the slots on the computer chassis.
3. Tilt the hard-disk drive assembly slightly at an angle.
4. Lift the hard-disk drive assembly from the computer.
NOTE: Note the orientation of the hard-disk drive so that you can replace it correctly.
Removing the 2.5-inch hard-disk drive bracket
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the fan duct.
4. Remove the 2.5 in. hard-disk drive assembly.
Disassembly and reassembly 25
About this task
The following images indicate the location of the 2.5-inch hard-disk drive bracket and provides a visual representation of the
removal procedure.
Steps
1. Remove the two (M3x3.5) screws that secure the first hard-disk drive to the hard-drive metal bracket.
2. Slide and lift the hard drive from the hard-drive metal bracket.
3. Remove the two (M3x3.5) screws that secure the second hard drive to the hard-disk drive metal bracket.
4. Slide and lift the second hard-disk drive from the hard-disk drive metal bracket.
Installing the 2.5-inch hard-disk drive bracket
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the 2.5-inch hard-disk drive bracket and provides a visual representation of the
installation procedure.
26 Disassembly and reassembly
Steps
1. Place the first hard-disk drive into the hard-disk drive metal bracket and align the slots on the bracket with the slots on the
hard-disk drive.
2. Replace the two (M3x3.5) screws to secure the first hard-disk drive to the hard-disk drive metal bracket.
3. Place the second hard-disk drive into the hard-disk drive metal bracket and align the slots on the bracket with the slots on
the hard-disk drive.
4. Replace the two (M3x3.5) screws to secure the second hard-disk drive to the hard-disk drive metal bracket.
Next steps
1. Install the 2.5 in. hard-disk drive assembly.
2. Install the fan duct.
3. Install the side cover.
4. Follow the procedure in after working inside your computer.
Installing the 2.5-inch hard-disk drive assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
Disassembly and reassembly 27
About this task
The following image indicates the location of the 2.5-inch hard-disk drive assembly and provides a visual representation of the
installation procedure.
Steps
1. Align the hard-drive assembly at an angle to the slot on the computer.
2. Press the release tabs on the hard-disk drive bracket and slightly align back to insert the hard-disk drive assembly to the slot
on the computer chassis.
3. Connect the hard-drive data and power cables to the connectors on the 2.5-inch hard-disk drive module.
Next steps
1. Install the fan duct.
2. Install the side cover.
3. Follow the procedure in after working inside your computer.
28 Disassembly and reassembly
3.5-inch hard drive
Removing the 3.5 inch hard drive
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the fan duct.
About this task
The following images indicate the location of the 3.5 inch hard drive and provides a visual representation of the removal
procedure.
Steps
1. Disconnect the data and power cables from the 3.5 inch hard drive.
2. Remove the four (#6-32) screws from the front-side of the chassis that secures the hard drive to the chassis.
3. Remove the 3.5 inch hard drive away from the chassis.
Installing the 3.5 inch hard drive
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the 3.5-inch hard drive and provides a visual representation of the installation
procedure.
Disassembly and reassembly 29
Steps
1. Align and insert the 3.5 inch hard drive into the slot on the chassis.
2. Hold the hard drive against the chassis and replace the four (#6-32) screws to secure the hard drive to the computer
chassis.
3. Connect the power cable and data cable to the hard drive.
Next steps
1. Install the fan duct.
2. Install the side cover.
3. Follow the procedure in after working inside your computer.
Solid-state drive
Removing the M.2 2230 PCIe solid-state drive
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the fan duct.
About this task
The following images indicate the location of the solid-state drive and provide a visual representation of the removal procedure.
30 Disassembly and reassembly
Steps
1. Remove the screw (M2x3.5) that secures the solid-state drive to the system board.
2. Slide and lift the solid-state drive off the system board.
Installing the M.2 2230 PCIe solid-state drive
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the solid-state drive and provides a visual representation of the installation
procedure.
Disassembly and reassembly 31
Steps
1. Align the notch on the solid-state drive with the tab on the solid-state drive connector.
2. Insert the solid-state drive at a 45-degree angle into the slot on the system board.
3. Replace the screw (M2x3.5) to secure the M.2 2230 solid-state drive to the system board.
Next steps
1. Install the fan duct.
2. Install the side cover.
3. Follow the procedure in after working inside your computer.
Removing the M.2 2280 PCIe solid-state drive
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the fan duct.
About this task
The following images indicate the location of the solid-state drive and provide a visual representation of the removal procedure.
32 Disassembly and reassembly
Steps
1. Remove the screw (M2x3.5) that secures the solid-state drive to the system board.
2. Slide and lift the solid-state drive off the system board.
Installing the M.2 2280 PCIe solid-state drive
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the solid-state drive and provides a visual representation of the installation
procedure.
Disassembly and reassembly 33
Steps
1. Align the notch on the solid-state drive with the tab on the solid-state drive connector.
2. Insert the solid-state drive at a 45-degree angle into the slot on the system board.
3. Replace the screw (M2x3.5) to secure the M.2 2280 solid-state drive to the system board.
Next steps
1. Install the fan duct.
2. Install the side cover.
3. Follow the procedure in after working inside your computer.
Memory modules
Removing the memory modules
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the fan duct.
About this task
The following images indicate the location of the memory modules and provide a visual representation of the removal procedure.
34 Disassembly and reassembly
Steps
1. Pull the securing clips from both side of the memory module until the memory module pops up.
2. Slide and remove the memory module from the memory-module slot.
Installing the memory modules
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the memory modules and provides a visual representation of the installation
procedure.
Disassembly and reassembly 35
Steps
1. Align the notch on the memory module with the tab on the memory-module slot.
2. Slide the memory module firmly into the slot at an angle and press the memory module down until it clicks into place.
NOTE: If you do not hear the click, remove the memory module and reinstall it.
Next steps
1. Install the fan duct.
2. Install the side cover.
3. Follow the procedure in after working inside your computer.
Processor fan and heat-sink assembly
Removing the processor fan and heat-sink assembly
Prerequisites
1. Follow the procedure in before working inside your computer.
WARNING: The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to
cool before you touch it.
CAUTION: For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The
oils in your skin can reduce the heat transfer capability of the thermal grease.
2. Remove the side cover.
3. Remove the fan duct.
36 Disassembly and reassembly
About this task
The following images indicate the location of the processor fan and heat-sink and provide a visual representation of the removal
procedure.
Steps
1. Disconnect the processor fan cable from the connector on the system board.
2. Loosen the four captive screws that secure the processor fan and heat-sink assembly to the system board.
3. Lift the processor fan and heat-sink assembly off the system board.
Installing the processor fan and heat-sink assembly
Prerequisites
NOTE: If either the processor or the heat sink is replaced, use the thermal grease provided in the kit to ensure that thermal
conductivity is achieved.
About this task
The following image indicates the location of the processor fan and heat-sink assembly and provides a visual representation of
the installation procedure.
Disassembly and reassembly 37
Steps
1. Align the screw holes on the processor fan and heat-sink assembly with the screw holes on the system board.
2. Tighten the four captive screws that secure the processor fan and heat-sink assembly to the system board.
3. Connect the processor-fan cable to the connector on the system board.
Next steps
1. Install the fan duct.
2. Install the side cover.
3. Follow the procedure in after working inside your computer.
Processor
Removing the processor
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the fan duct.
4. Remove the processor fan and heat-sink assembly.
NOTE: The processor might still be hot after the computer is shut down. Allow the processor to cool down before removing
it.
38 Disassembly and reassembly
About this task
The following images indicate the location of the processor and provide a visual representation of the removal procedure.
Steps
1. Press down and push the release lever away from the processor to release it from the securing tab.
2. Lift the lever upward to lift the processor cover.
CAUTION: When removing the processor, do not touch any of the pins inside the socket or allow any objects
to fall on the pins in the socket.
3. Gently lift the processor from the processor socket.
Installing the processor
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the processor and provides a visual representation of the installation procedure.
Disassembly and reassembly 39
Steps
1. Ensure that the release lever on the processor socket is fully extended in the open position.
2. Align the notches on the processor with the tabs on the processor socket and place the processor in the processor socket.
NOTE: The pin-1 corner of the processor has a triangle that aligns with the triangle on the pin-1 corner on the processor
socket. When the processor is properly seated, all four corners are aligned at the same height. If one or more corners of
the processor are higher than the others, the processor is not seated properly.
3. When the processor is fully seated in the socket, pivot the release-lever down and place it under the tab on the processor
cover.
Next steps
1. Install the processor fan and heat-sink assembly.
2. Install the fan duct.
3. Install the side cover.
4. Follow the procedure in after working inside your computer.
40 Disassembly and reassembly
Graphics card
Removing the graphics card
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the fan duct.
About this task
The following images indicate the location of the graphics card and provides a visual representation of the removal procedure.
Steps
1. Locate the graphics card (PCI-Express).
2. Lift the pull tab to open the PCIe door.
3. Push and hold the securing tab on the graphics-card slot and lift the graphics card from the graphics-card slot.
Disassembly and reassembly 41
Installing the graphics card
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the graphics card and provides a visual representation of the installation procedure.
Steps
1. Align the graphics card with the PCI-Express card connector on the system board.
2. Using the alignment post, connect the graphics card in the connector and press down firmly. Ensure that the card is firmly
seated.
3. Lift the pull tab to close the PCIe door.
Next steps
1. Install the fan duct.
2. Install the side cover.
3. Follow the procedure in after working inside your computer.
42 Disassembly and reassembly
Graphical processing unit
Removing the powered GPU
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the fan duct.
About this task
The following images indicate the location of the powered graphical processing unit and provides a visual representation of the
removal procedure.
Steps
1. Disconnect the two power cables from the connectors on the powered GPU.
2. Lift the pull tab to open the PCIe door.
3. Push and hold the securing tab on the graphics-card slot and lift the powered GPU away from the graphics-card slot.
Installing the powered GPU
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the powered graphical processing unit and provides a visual representation of the
installation procedure.
Steps
1. Align the powered GPU with the PCI-Express card connector on the system board.
2. Using the alignment post, connect the powered GPU in the connector and press down firmly. Ensure that the powered GPU
is firmly seated.
3. Lift the pull tab to close the PCIe door.
4. Connect the two power cables to the connector on the powered GPU.
Next steps
1. Install the fan duct.
2. Install the side cover.
3. Follow the procedure in after working inside your computer.
Coin-cell battery
Removing the coin-cell battery
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the fan duct.
4. Remove the powered GPU.
Disassembly and reassembly 43
NOTE: This step is required only if the system is configured with powered GPU.
About this task
The following images indicate the location of the coin-cell battery and provide a visual representation of the removal procedure.
Steps
1. Using a plastic scribe, gently pry the coin-cell battery out of the slot on the system board.
2. Remove the coin-cell battery away from the computer.
Installing the coin-cell battery
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the coin-cell battery and provides a visual representation of the installation
procedure.
44 Disassembly and reassembly
Steps
1. Insert the coin cell battery with the "+" sign facing up and slide it under the securing tabs at the positive side of the
connector.
2. Press the battery into the connector until it locks into place.
Next steps
1. Install the powered GPU.
NOTE: This step is required only if the system is configured with powered GPU.
2. Install the fan duct.
3. Install the side cover.
4. Follow the procedure in after working inside your computer.
WLAN card
Removing the WLAN card
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the fan duct.
4. Remove the powered GPU.
NOTE: This step is required only if the system is configured with powered GPU.
About this task
The following images indicate the location of the wireless card and provide a visual representation of the removal procedure.
Disassembly and reassembly 45
Steps
1. Remove the (M2x3.5) screw that secures the WLAN card to the system board.
2. Lift the WLAN card bracket away from the WLAN card.
3. Disconnect the antenna cables from the WLAN card.
4. Slide and remove the WLAN card from the connector on the system board.
Installing the WLAN card
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the wireless card and provides a visual representation of the installation procedure.
46 Disassembly and reassembly
Steps
1. Connect the antenna cables to the WLAN card.
The following table provides the antenna-cable color scheme for the WLAN card of your computer.
Table 6. Antenna-cable color scheme
Connectors on the wireless card Antenna-cable color
Main (white triangle) White
Auxiliary (black triangle) Black
2. Place the WLAN card bracket to secure the WLAN antenna cables.
3. Insert the WLAN card into the connector on the system board.
4. Replace the (M2x3.5) screw to secure the plastic tab to the WLAN card.
Next steps
1. Install the powered GPU.
NOTE: This step is required only if the system is configured with powered GPU.
2. Install the fan duct.
3. Install the side cover.
4. Follow the procedure in after working inside your computer.
Disassembly and reassembly 47
Slim optical-drive
Removing the Slim-Optical Disk Drive
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the fan duct.
About this task
The following images indicate the location of the slim ODD and provides a visual representation of the removal procedure.
Steps
1. Disconnect the data and power cables from the slim ODD.
2. Pull the securing tab to release the slim ODD from the chassis.
3. Slide and remove the slim ODD from the ODD slot.
Installing the Slim-Optical Disk Drive
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the slim ODD and provide a visual representation of the installation procedure.
48 Disassembly and reassembly
Steps
1. Insert the slim ODD assembly into the ODD slot.
2. Slide the slim ODD assembly until it snaps into place.
3. Route the power cable and data cable through the routing guides and connect the cables to the slim ODD.
Next steps
1. Install the fan duct.
2. Install the side cover.
3. Follow the procedure in after working inside your computer.
Slim optical-drive bracket
Removing the slim-ODD bracket
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the fan duct.
4. Remove the slim Optical Disk Drive.
About this task
The following images indicate the location of the slim-ODD bracket and provides a visual representation of the removal
procedure.
Disassembly and reassembly 49
Steps
1. Pry the slim-ODD bracket to release it from the slot on the ODD.
2. Remove the slim-ODD bracket off the ODD.
Installing the slim-ODD bracket
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the slim-ODD bracket and provides a visual representation of the installation
procedure.
Steps
1. Align and place the slim-ODD bracket on the ODD slots.
2. Snap the slim-ODD bracket into the slim ODD.
Next steps
1. Install the slim Optical Disk Drive.
2. Install the fan duct.
3. Install the side cover.
50 Disassembly and reassembly
4. Follow the procedure in after working inside your computer.
Speaker
Removing the speaker
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the fan duct.
About this task
The following images indicate the location of the speakers and provide a visual representation of the removal procedure.
Steps
1. Disconnect the speaker cable from the connector on the system board.
2. Unroute the speaker cable from the routing guides on the chassis.
3. Press the tab and slide the speaker along with the cable from the slot on the chassis.
Installing the speaker
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the speaker and provides a visual representation of the installation procedure.
Disassembly and reassembly 51
Steps
1. Press and slide the speaker in the slot on the chassis until it snaps into place.
2. Route the speaker cable through the routing guide on the chassis.
3. Connect the speaker cable to the connector on the system board.
Next steps
1. Install the fan duct.
2. Install the side cover.
3. Follow the procedure in after working inside your computer.
Power button
Removing the power button
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the fan duct.
4. Remove the front bezel.
About this task
The following images indicate the location of the power button and provides a visual representation of the removal procedure.
52 Disassembly and reassembly
Steps
1. Disconnect the power-button cable from the connector on the system board.
2. Press the release tabs on the power-button head and slide the power-button cable out from the front-side chassis of the
computer.
3. Pull the power-button cable out from the computer.
Installing the power button
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the power button switch and provides a visual representation of the installation
procedure.
Disassembly and reassembly 53
Steps
1. Insert the power-button cable into the slot from the front-side of the computer, and press the power-button head until it
clicks into the place in the chassis.
2. Align and connect the power-button cable to the connector on the system board.
Next steps
1. Install the front bezel.
2. Install the fan duct.
3. Install the side cover.
4. Follow the procedure in after working inside your computer.
Power-supply unit
Removing the power-supply unit
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the fan duct.
NOTE: Note the routing of all cables as you remove them so that you can route them correctly while you are replacing the
power-supply unit.
About this task
The following images indicate the location of the power-supply unit and provides a visual representation of the removal
procedure.
54 Disassembly and reassembly
Disassembly and reassembly 55
Steps
1. Lay the computer on the right side.
2. Disconnect the power cables from the system board and unroute them from the routing guides on the chassis.
3. Remove the three (#6-32) screws that secure the power-supply unit to the chassis.
4. Press the securing clip and slide the power-supply unit away from the back of the chassis.
5. Lift the power-supply unit off the chassis.
Installing the power-supply unit
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
WARNING: The cables and ports on the back of the power-supply unit are color-coded to indicate the different
power wattage. Ensure that you plug in the cable to the correct port. Failure to do so may result in damaging
the power-supply unit and/or system components.
About this task
The following images indicate the location of the power-supply unit and provides a visual representation of the installation
procedure.
56 Disassembly and reassembly
Disassembly and reassembly 57
Steps
1. Slide the power-supply unit into the chassis until the securing tab snaps into position.
2. Replace the three (#6-32) screws to secure the power-supply unit to the chassis.
3. Route the power cable through the routing guides on the chassis and connect the power cables to their respective
connectors on the system board.
Next steps
1. Install the fan duct.
2. Install the side cover.
3. Follow the procedure in after working inside your computer.
Intrusion switch
Removing the intrusion switch
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the fan duct.
About this task
The following images indicate the location of the intrusion switch and provides a visual representation of the removal procedure.
58 Disassembly and reassembly
Steps
1. Disconnect the intruder cable from the connector on the system board.
2. Slide and remove the intrusion switch from the chassis.
Installing the intrusion switch
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the intrusion switch and provides a visual representation of the installation
procedure.
Disassembly and reassembly 59
Steps
1. Insert the intrusion switch into its slot and slide the switch to secure it into the slot.
2. Connect the intruder cable to the connector on the system board.
Next steps
1. Install the fan duct.
2. Install the side cover.
3. Follow the procedure in after working inside your computer.
Optional I/O modules (Type C/ HDMI/VGA/DP/Serial)
Removing optional I/O modules (Type C/ HDMI/VGA/DP/Serial)
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the side cover.
3. Remove the front bezel.
4. Remove the fan duct.
About this task
The following images indicate the location of the optional I/O Modules and provides a visual representation of the removal
procedure.
Steps
1. Remove the two (M3X3) screws that secure the optional i/O module to the computer chassis.
2. Disconnect the I/O-module cable from the connector on the system board.
60 Disassembly and reassembly
3. Remove the I/O module from the computer.
Installing optional I/O modules (Type-C/HDMI/VGA/DP/Serial)
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the system board and provides a visual representation of the installation procedure.
Disassembly and reassembly 61
62 Disassembly and reassembly
Disassembly and reassembly 63
Steps
1. To remove the dummy metal bracket, insert a flathead screwdriver in the hole of the bracket, push the bracket to release
the bracket, and then lift the bracket out from the system.
2. Insert the optional I/O module (Type-C/HDMI/VGA/DP/Serial) into its slot from the inside of your computer.
3. Connect the I/O cable to the connector on the system board .
4. Replace the two (M3X3) screws to secure the optional I/O module to the system.
Next steps
1. Install the fan duct.
2. Install the front bezel.
3. Install the side cover.
4. Follow the procedure in after working inside your computer.
64 Disassembly and reassembly
System board
Removing the system board
Prerequisites
1. Follow the procedure in before working inside your computer.
NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup
program after you replace the system board.
NOTE: Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup
program. You must make the appropriate changes again after you replace the system board.
NOTE: Before disconnecting the cables from the system board, note the location of the connectors so that you can
reconnect the cables correctly after you replace the system board.
2. Remove the side cover.
3. Remove the front bezel.
4. Remove the fan duct.
5. Remove the memory module.
6. Remove the wireless.
7. Remove the M.2 2230 SSD/M.2 2280 SSD.
8. Remove the coin-cell battery.
9. Remove the graphics card/ powered graphical processing unit.
10. Remove the processor fan and heat-sink assembly.
11. Remove the processor.
About this task
The following images indicate the location of the system board and provides a visual representation of the removal procedure.
Disassembly and reassembly 65
66 Disassembly and reassembly
Steps
1. Remove the two (#6-32) screws that secure the front I/O-bracket to the chassis.
2. Slide and remove the front I/O-bracket from the chassis.
3. Disconnect all the cables that are connected to the system board.
4. Remove the M.2 card standoff (#6-32) screw and eight (#6-32) screws that secure the system board to the chassis.
Disassembly and reassembly 67
5. Lift the system board at an angle and remove the system board off the chassis.
Installing the system board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the system board and provides a visual representation of the installation procedure.
68 Disassembly and reassembly
Disassembly and reassembly 69
Steps
1. Slide the front I/O-ports on the system board into the front I/O-slots on the chassis and align the screw holes on the
system board with the screw holes on the chassis.
2. Replace the M.2 card standoff (#6-32) screw and eight (#6-32) screws that secure the system board to the chassis.
3. Route and connect all the cables to the connectors on the system board.
70 Disassembly and reassembly
4. Align the front I/O-bracket with the slots on the chassis.
5. Replace the two (#6-32) screws to secure the front I/O-bracket to the chassis.
Next steps
1. Install the processor.
2. Install the processor fan and heat-sink assembly.
3. Install the coin-cell battery.
4. Install the graphics card/powered GPU.
5. Install the M.2 2230 SSD/M.2 2280 SSD.
6. Install the wireless.
7. Install the memory module.
8. Install the fan duct
9. Install the front bezel.
10. Install the side cover.
11. Follow the procedure in after working inside your computer.
NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup
program after you replace the system board.
NOTE: Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup
program. You must make the appropriate changes again after you replace the system board.
Disassembly and reassembly 71
Troubleshooting
Topics:
•Dell SupportAssist Pre-boot System Performance Check diagnostics
•Diagnostic LED behavior
•Diagnostic error messages
•System error messages
•WiFi power cycle
Dell SupportAssist Pre-boot System Performance
Check diagnostics
About this task
The SupportAssist diagnostics (also known as system diagnostics) performs a complete check of your hardware. The Dell
SupportAssist Pre-boot System Performance Check diagnostics is embedded with the BIOS and is launched by the BIOS
internally. The embedded system diagnostics provides a set of options for particular devices or device groups allowing you to:
●Run tests automatically or in an interactive mode
●Repeat tests
●Display or save test results
●Run thorough tests to introduce additional test options to provide extra information about the failed device(s)
●View status messages that inform you if tests are completed successfully
●View error messages that inform you of problems encountered during testing
NOTE: Some tests for specific devices require user interaction. Always ensure that you are present at the computer
terminal when the diagnostic tests are performed.
For more information, see Resolve Hardware Issues With Built-in and Online Diagnostics (SupportAssist ePSA, ePSA or PSA
Error Codes) .
Running the SupportAssist Pre-Boot System Performance Check
Steps
1. Turn on your computer.
2. As the computer boots, press the F12 key as the Dell logo appears.
3. On the boot menu screen, select the Diagnostics option.
4. Click the arrow at the bottom left corner.
Diagnostics front page is displayed.
5. Click the arrow in the lower-right corner to go to the page listing.
The items detected are listed.
6. To run a diagnostic test on a specific device, press Esc and click Yes to stop the diagnostic test.
7. Select the device from the left pane and click Run Tests.
8. If there are any issues, error codes are displayed.
Note the error code and validation number and contact Dell.
5
72 Troubleshooting
Diagnostic LED behavior
Table 7. Diagnostic LED behavior
Blinking pattern
Problem description Suggested resolutionAmber White
1 2 Unrecoverable SPI Flash
Failure
2 1 CPU failure ●Run the Intel CPU
diagnostics tools.
●If problem persists,
replace the system board.
2 2 System board failure (included
BIOS corruption or ROM
error)
●Flash latest BIOS version
●If problem persists,
replace the system board.
2 3 No memory/RAM detected ●Confirm that the memory
module is installed
properly.
●If problem persists,
replace the memory
module.
2 4 Memory/RAM failure ●Reset the memory module.
●If problem persists,
replace the memory
module.
2 5 Invalid memory installed ●Reset the memory module.
●If problem persists,
replace the memory
module.
2 6 System board / Chipset
Error / Clock failure / Gate
A20 failure / Super I/O
failure / Keyboard controller
failure
●Flash latest BIOS version
●If problem persists,
replace the system board.
3 1 CMOS battery failure ●Reset the CMOS battery
connection.
●If problem persists,
replace the RTS battery.
3 2 PCI or Video card/chip failure Replace the system board.
3 3 BIOS Recovery image not
found
●Flash latest BIOS version
●If problem persists,
replace the system board.
3 4 BIOS Recovery image found
but invalid
●Flash latest BIOS version
●If problem persists,
replace the system board.
3 5 Power rail failure ●EC ran into power
sequencing failure.
●If problem persists,
replace the system board.
Troubleshooting 73
Table 7. Diagnostic LED behavior (continued)
Blinking pattern
Problem description Suggested resolutionAmber White
3 6 SBIOS Flash corruption ●Flash corruption detected
by SBIOS
●If problem persists,
replace the system board.
3 7 Intel ME (Management
Engine) Error
●Timeout waiting on ME to
reply to HECI message
●If problem persists,
replace the system board.
4 2 CPU Power Cable Connection
Issue
Diagnostic error messages
Table 8. Diagnostic error messages
Error messages Description
AUXILIARY DEVICE FAILURE The touchpad or external mouse may be faulty. For an
external mouse, check the cable connection. Enable the
Pointing Device option in the System Setup program.
BAD COMMAND OR FILE NAME Ensure that you have spelled the command correctly, put
spaces in the proper place, and used the correct path name.
CACHE DISABLED DUE TO FAILURE The primary cache internal to the microprocessor has failed.
Contact Dell
CD DRIVE CONTROLLER FAILURE The optical drive does not respond to commands from the
computer.
DATA ERROR The hard drive cannot read the data.
DECREASING AVAILABLE MEMORY One or more memory modules may be faulty or improperly
seated. Reinstall the memory modules or, if necessary, replace
them.
DISK C: FAILED INITIALIZATION The hard drive failed initialization. Run the hard drive tests in
Dell Diagnostics.
DRIVE NOT READY The operation requires a hard drive in the bay before it can
continue. Install a hard drive in the hard drive bay.
ERROR READING PCMCIA CARD The computer cannot identify the ExpressCard. Reinsert the
card or try another card.
EXTENDED MEMORY SIZE HAS CHANGED The amount of memory recorded in non-volatile memory
(NVRAM) does not match the memory module installed in the
computer. Restart the computer. If the error appears again,
Contact Dell
THE FILE BEING COPIED IS TOO LARGE FOR THE
DESTINATION DRIVE
The file that you are trying to copy is too large to fit on the
disk, or the disk is full. Try copying the file to a different disk
or use a larger capacity disk.
A FILENAME CANNOT CONTAIN ANY OF THE
FOLLOWING CHARACTERS: \ / : * ? " < > | -
Do not use these characters in filenames.
GATE A20 FAILURE A memory module may be loose. Reinstall the memory module
or, if necessary, replace it.
74 Troubleshooting
Table 8. Diagnostic error messages (continued)
Error messages Description
GENERAL FAILURE The operating system is unable to carry out the command.
The message is usually followed by specific information. For
example, Printer out of paper. Take the
appropriate action.
HARD-DISK DRIVE CONFIGURATION ERROR The computer cannot identify the drive type. Shut down the
computer, remove the hard drive, and boot the computer from
an optical drive. Then, shut down the computer, reinstall the
hard drive, and restart the computer. Run the Hard Disk
Drive tests in Dell Diagnostics.
HARD-DISK DRIVE CONTROLLER FAILURE 0 The hard drive does not respond to commands from the
computer. Shut down the computer, remove the hard drive,
and boot the computer from an optical drive. Then, shut down
the computer, reinstall the hard drive, and restart the
computer. If the problem persists, try another drive. Run the
Hard Disk Drive tests in Dell Diagnostics.
HARD-DISK DRIVE FAILURE The hard drive does not respond to commands from the
computer. Shut down the computer, remove the hard drive,
and boot the computer from an optical drive. Then, shut down
the computer, reinstall the hard drive, and restart the
computer. If the problem persists, try another drive. Run the
Hard Disk Drive tests in Dell Diagnostics.
HARD-DISK DRIVE READ FAILURE The hard drive may be defective. Shut down the computer,
remove the hard drive, and boot the computer from an
optical. Then, shut down the computer, reinstall the hard
drive, and restart the computer. If the problem persists, try
another drive. Run the Hard Disk Drive tests in Dell
Diagnostics.
INSERT BOOTABLE MEDIA The operating system is trying to boot to non-bootable media,
such as an optical drive. Insert bootable media.
INVALID CONFIGURATION INFORMATION-PLEASE RUN
SYSTEM SETUP PROGRAM
The system configuration information does not match the
hardware configuration. The message is most likely to occur
after a memory module is installed. Correct the appropriate
options in the system setup program.
KEYBOARD CLOCK LINE FAILURE For external keyboards, check the cable connection. Run the
Keyboard Controller test in Dell Diagnostics.
KEYBOARD CONTROLLER FAILURE For external keyboards, check the cable connection. Restart
the computer, and avoid touching the keyboard or the mouse
during the boot routine. Run the Keyboard Controller test in
Dell Diagnostics.
KEYBOARD DATA LINE FAILURE For external keyboards, check the cable connection. Run the
Keyboard Controller test in Dell Diagnostics.
KEYBOARD STUCK KEY FAILURE For external keyboards or keypads, check the cable
connection. Restart the computer, and avoid touching the
keyboard or keys during the boot routine. Run the Stuck Key
test in Dell Diagnostics.
LICENSED CONTENT IS NOT ACCESSIBLE IN
MEDIADIRECT
Dell MediaDirect cannot verify the Digital Rights Management
(DRM) restrictions on the file, so the file cannot be played.
MEMORY ADDRESS LINE FAILURE AT ADDRESS, READ
VALUE EXPECTING VALUE
A memory module may be faulty or improperly seated.
Reinstall the memory module or, if necessary, replace it.
MEMORY ALLOCATION ERROR The software you are attempting to run is conflicting with the
operating system, another program, or a utility. Shut down the
computer, wait for 30 seconds, and then restart it. Run the
Troubleshooting 75
Table 8. Diagnostic error messages (continued)
Error messages Description
program again. If the error message still appears, see the
software documentation.
MEMORY DOUBLE WORD LOGIC FAILURE AT ADDRESS,
READ VALUE EXPECTING VALUE
A memory module may be faulty or improperly seated.
Reinstall the memory module or, if necessary, replace it.
MEMORY ODD/EVEN LOGIC FAILURE AT ADDRESS,
READ VALUE EXPECTING VALUE
A memory module may be faulty or improperly seated.
Reinstall the memory module or, if necessary, replace it.
MEMORY WRITE/READ FAILURE AT ADDRESS, READ
VALUE EXPECTING VALUE
A memory module may be faulty or improperly seated.
Reinstall the memory module or, if necessary, replace it.
NO BOOT DEVICE AVAILABLE The computer cannot find the hard drive. If the hard drive is
your boot device, ensure that the drive is installed, properly
seated, and partitioned as a boot device.
NO BOOT SECTOR ON HARD DRIVE The operating system may be corrupted, Contact Dell.
NO TIMER TICK INTERRUPT A chip on the system board may be malfunctioning. Run the
System Set tests in Dell Diagnostics.
NOT ENOUGH MEMORY OR RESOURCES. EXIT SOME
PROGRAMS AND TRY AGAIN
You have too many programs open. Close all windows and
open the program that you want to use.
OPERATING SYSTEM NOT FOUND Reinstall the operating system. If the problem persists,
Contact Dell.
OPTIONAL ROM BAD CHECKSUM The optional ROM has failed. Contact Dell.
SECTOR NOT FOUND The operating system cannot locate a sector on the hard
drive. You may have a defective sector or corrupted File
Allocation Table (FAT) on the hard drive. Run the Windows
error-checking utility to check the file structure on the hard
drive. See Windows Help and Support for instructions (click
Start > Help and Support). If a large number of sectors are
defective, back up the data (if possible), and then format the
hard drive.
SEEK ERROR The operating system cannot find a specific track on the hard
drive.
SHUTDOWN FAILURE A chip on the system board may be malfunctioning. Run the
System Set tests in Dell Diagnostics. If the message
reappears, Contact Dell.
TIME-OF-DAY CLOCK LOST POWER System configuration settings are corrupted. Connect your
computer to an electrical outlet to charge the battery. If the
problem persists, try to restore the data by entering the
System Setup program, then immediately exit the program. If
the message reappears, Contact Dell.
TIME-OF-DAY CLOCK STOPPED The reserve battery that supports the system configuration
settings may require recharging. Connect your computer to an
electrical outlet to charge the battery. If the problem persists,
Contact Dell.
TIME-OF-DAY NOT SET-PLEASE RUN THE SYSTEM
SETUP PROGRAM
The time or date stored in the system setup program does not
match the system clock. Correct the settings for the Date
and Time options.
TIMER CHIP COUNTER 2 FAILED A chip on the system board may be malfunctioning. Run the
System Set tests in Dell Diagnostics.
UNEXPECTED INTERRUPT IN PROTECTED MODE The keyboard controller may be malfunctioning, or a memory
module may be loose. Run the System Memory tests and the
Keyboard Controller test in Dell Diagnostics or Contact
Dell.
76 Troubleshooting
Table 8. Diagnostic error messages (continued)
Error messages Description
X:\ IS NOT ACCESSIBLE. THE DEVICE IS NOT
READY
Insert a disk into the drive and try again.
System error messages
Table 9. System error messages
System message Description
Alert! Previous attempts at booting this
system have failed at checkpoint [nnnn]. For
help in resolving this problem, please note
this checkpoint and contact Dell Technical
Support
The computer failed to complete the boot routine three
consecutive times for the same error.
CMOS checksum error RTC is reset, BIOS Setup default has been loaded.
CPU fan failure CPU fan has failed.
System fan failure System fan has failed.
Hard-disk drive failure Possible hard disk drive failure during POST.
Keyboard failure Keyboard failure or loose cable. If reseating the cable does not
solve the problem, replace the keyboard.
No boot device available No bootable partition on hard disk drive, the hard disk drive
cable is loose, or no bootable device exists.
●If the hard drive is your boot device, ensure that the
cables are connected and that the drive is installed
properly and partitioned as a boot device.
●Enter system setup and ensure that the boot sequence
information is correct.
No timer tick interrupt A chip on the system board might be malfunctioning or
motherboard failure.
NOTICE - Hard Drive SELF MONITORING SYSTEM
has reported that a parameter has exceeded
its normal operating range. Dell recommends
that you back up your data regularly. A
parameter out of range may or may not
indicate a potential hard drive problem
S.M.A.R.T error, possible hard disk drive failure.
WiFi power cycle
About this task
If your computer is unable to access the internet due to WiFi connectivity issues a WiFi power cycle procedure may be
performed. The following procedure provides the instructions on how to conduct a WiFi power cycle:
NOTE: Some ISPs (Internet Service Providers) provide a modem/router combo device.
Steps
1. Turn off your computer.
2. Turn off the modem.
3. Turn off the wireless router.
4. Wait for 30 seconds.
Troubleshooting 77
5. Turn on the wireless router.
6. Turn on the modem.
7. Turn on your computer.
78 Troubleshooting
Getting help
Topics:
•Contacting Dell
Contacting Dell
Prerequisites
NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing
slip, bill, or Dell product catalog.
About this task
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and
some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues:
Steps
1. Go to Dell.com/support.
2. Select your support category.
3. Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.
4. Select the appropriate service or support link based on your need.
6
Getting help 79