Table of Contents
- Latitude 3320 Service Manual
- Contents
- Working inside your computer
- Removing and installing components
- Drivers and downloads
- System setup
- Troubleshooting
- Built-in self-test (BIST)
- LCD Built-in Self Test (BIST)
- Dell SupportAssist Pre-boot System Performance Check diagnostics
- Diagnostic LED behavior
- Diagnostic error messages
- System error messages
- Recovering the operating system
- Real-Time Clock (RTC Reset)
- Flashing the BIOS
- Backup media and recovery options
- WiFi power cycle
- Flea power release
- Getting help and contacting Dell
DELL 3320 User Manual
Displayed below is the user manual for 3320 by DELL which is a product in the Notebooks category. This manual has pages.
Related Manuals
Latitude 3320
Service Manual
Regulatory Model: P146G
Regulatory Type: P146G001
April 2021
Rev. A00
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid
the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other
trademarks may be trademarks of their respective owners.
Chapter 1: Working inside your computer...................................................................................... 6
Safety instructions.............................................................................................................................................................. 6
Before working inside your computer.......................................................................................................................6
Entering Service Mode................................................................................................................................................. 7
Exiting Service Mode.................................................................................................................................................... 7
Safety precautions.........................................................................................................................................................7
Electrostatic discharge—ESD protection............................................................................................................... 8
ESD field service kit ..................................................................................................................................................... 8
Transporting sensitive components.......................................................................................................................... 9
After working inside your computer..........................................................................................................................9
Chapter 2: Removing and installing components.......................................................................... 10
Recommended tools..........................................................................................................................................................10
Screw List............................................................................................................................................................................ 10
Major components of your system................................................................................................................................ 12
MicroSD-card......................................................................................................................................................................13
Removing the microSD-card..................................................................................................................................... 13
Installing the MicroSD-card....................................................................................................................................... 14
Base cover........................................................................................................................................................................... 14
Removing the base cover...........................................................................................................................................14
Installing the base cover.............................................................................................................................................16
Solid-state drive................................................................................................................................................................. 17
Removing the M.2 2230 solid-state drive.............................................................................................................. 17
Installing the M.2 2230 solid-state drive................................................................................................................ 18
Removing the M.2 2280 solid-state drive............................................................................................................. 20
Installing the M.2 2280 solid-state drive............................................................................................................... 20
Speakers...............................................................................................................................................................................21
Removing the speakers...............................................................................................................................................21
Installing the speakers................................................................................................................................................ 22
WLAN card..........................................................................................................................................................................23
Removing the WLAN card......................................................................................................................................... 23
Installing the WLAN card........................................................................................................................................... 24
Coin-cell battery................................................................................................................................................................ 26
Removing the coin-cell battery................................................................................................................................26
Installing the coin-cell battery.................................................................................................................................. 26
Battery cable...................................................................................................................................................................... 27
Installing the battery cable........................................................................................................................................ 27
Removing the battery cable......................................................................................................................................28
Battery................................................................................................................................................................................. 29
Removing the 3-cell battery..................................................................................................................................... 29
Installing the 3-cell battery....................................................................................................................................... 30
Removing the 4-cell battery......................................................................................................................................31
Installing the 4-cell battery....................................................................................................................................... 32
System fan.......................................................................................................................................................................... 33
Contents
Contents 3
Removing the left system fan.................................................................................................................................. 33
Installing the left system fan.................................................................................................................................... 34
Removing the right system fan................................................................................................................................35
Installing the right system fan..................................................................................................................................36
Display assembly................................................................................................................................................................38
Removing the display assembly............................................................................................................................... 38
Installing the display assembly..................................................................................................................................40
Input Output board........................................................................................................................................................... 42
Removing the Input Output board.......................................................................................................................... 42
Installing the Input Output board.............................................................................................................................43
Heatsink assembly.............................................................................................................................................................44
Removing the heatsink assembly.............................................................................................................................44
Installing the heatsink assembly...............................................................................................................................45
Touchpad ........................................................................................................................................................................... 46
Removing the touchpad.............................................................................................................................................46
Installing the touchpad............................................................................................................................................... 47
Power-button board......................................................................................................................................................... 48
Removing the power-button board.........................................................................................................................48
Installing the power-button board...........................................................................................................................49
System board..................................................................................................................................................................... 50
Removing the system board.....................................................................................................................................50
Installing the system board....................................................................................................................................... 53
Power adapter port.......................................................................................................................................................... 56
Removing the power adapter port.......................................................................................................................... 56
Installing the power adapter port............................................................................................................................ 57
Palmrest assembly............................................................................................................................................................ 58
Removing the palmrest assembly............................................................................................................................58
Chapter 3: Drivers and downloads............................................................................................... 60
Chapter 4: System setup............................................................................................................. 61
Boot menu........................................................................................................................................................................... 61
Boot Sequence................................................................................................................................................................... 61
Navigation keys..................................................................................................................................................................62
System setup options.......................................................................................................................................................62
Updating the BIOS in Windows ..................................................................................................................................... 71
Updating BIOS on systems with BitLocker enabled.............................................................................................71
Updating your system BIOS using a USB flash drive.......................................................................................... 72
System and setup password...........................................................................................................................................72
Assigning a system setup password....................................................................................................................... 73
Deleting or changing an existing system setup password................................................................................. 73
Chapter 5: Troubleshooting......................................................................................................... 74
Built-in self-test (BIST)................................................................................................................................................... 74
LCD Built-in Self Test (BIST)......................................................................................................................................... 74
Dell SupportAssist Pre-boot System Performance Check diagnostics................................................................75
Running the SupportAssist Pre-Boot System Performance Check................................................................75
Diagnostic LED behavior..................................................................................................................................................75
Diagnostic error messages.............................................................................................................................................. 77
4Contents
System error messages................................................................................................................................................... 80
Recovering the operating system................................................................................................................................. 80
Real-Time Clock (RTC Reset)........................................................................................................................................ 81
Flashing the BIOS...............................................................................................................................................................81
Backup media and recovery options..............................................................................................................................81
WiFi power cycle................................................................................................................................................................ 81
Flea power release............................................................................................................................................................ 82
Chapter 6: Getting help and contacting Dell................................................................................ 83
Contents 5
Working inside your computer
Safety instructions
Prerequisites
Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless
otherwise noted, each procedure included in this document assumes that the following conditions exist:
●You have read the safety information that shipped with your computer.
●A component can be replaced or, if purchased separately, installed by performing the removal procedure in reverse order.
About this task
WARNING: Before working inside your computer, read the safety information that shipped with your computer.
For additional safety best practices information, see the Regulatory Compliance Homepage
CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by
your warranty. Read and follow the safety instructions that came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically
touching an unpainted metal surface at the same time as touching a connector on the back of the computer.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a
card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by
its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some
cables have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking
tabs before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending
any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and
aligned.
NOTE: Disconnect all power sources before opening the computer cover or panels. After you finish working inside the
computer, replace all covers, panels, and screws before connecting to the power source.
NOTE: The color of your computer and certain components may appear differently than shown in this document.
Before working inside your computer
Steps
1. Save and close all open files and exit all open applications.
2. Shut down your computer. Click Start > Power > Shut down.
NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down
instructions.
3. Disconnect your computer and all attached devices from their electrical outlets.
4. Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.
5. Remove any media card and optical disc from your computer, if applicable.
1
6 Working inside your computer
6. After the computer is unplugged, press and hold the power button for 5 seconds to ground the system board.
CAUTION: Place the computer on a flat, soft, and clean surface to avoid scratches on the display.
7. Place the computer face down.
Entering Service Mode
Service Mode allows users to immediately cut off electricity from the computer and conduct repairs without disconnecting the
battery cable from the system board.
To enter Service Mode:
1. Shut down your computer and disconnect the AC adapter.
2. Hold <B> key on the keyboard and press the power button for 3 seconds or until the Dell logo appears on the screen.
3. Press any key to continue.
NOTE: If the power adapter has not been disconnected, a message prompting you to remove the AC adapter appears
on the screen. Remove the AC adapter and then press any key to continue the Service Mode procedure.
NOTE: The Service Mode procedure automatically skips the following step if the Owner Tag of the computer is not
set up in advance by the manufacturer.
4. When the ready-to-proceed message appears on the screen, press any key to proceed. The computer emits three short
beeps and shuts down immediately.
Once the computer shuts down, you may perform the replacement procedures without disconnecting the battery cable from
the system board.
Exiting Service Mode
Service Mode allows users to immediately cut off electricity from the computer and conduct repairs without disconnecting the
battery cable from the system board.
To exit Service Mode:
1. Connect the AC adapter to the power-adapter port on your computer.
2. Press the power button to turn on the computer. Your computer will automatically return to normal functioning mode.
Safety precautions
The safety precautions chapter details the primary steps to be taken before performing any disassembly instructions.
Observe the following safety precautions before you perform any installation or break/fix procedures involving disassembly or
reassembly:
●Turn off the system and all attached peripherals.
●Disconnect the system and all attached peripherals from AC power.
●Disconnect all network cables, telephone, and telecommunications lines from the system.
●Use an ESD field service kit when working inside any notebook to avoid electrostatic discharge (ESD) damage.
●After removing any system component, carefully place the removed component on an anti-static mat.
●Wear shoes with non-conductive rubber soles to reduce the chance of getting electrocuted.
Standby power
Dell products with standby power must be unplugged before you open the case. Systems that incorporate standby power are
essentially powered while turned off. The internal power enables the system to be remotely turned on (wake on LAN) and
suspended into a sleep mode and has other advanced power management features.
Unplugging, pressing and holding the power button for 20 seconds should discharge residual power in the system board.
Remove the battery from notebooks.
Working inside your computer 7
Bonding
Bonding is a method for connecting two or more grounding conductors to the same electrical potential. This is done through
the use of a field service electrostatic discharge (ESD) kit. When connecting a bonding wire, ensure that it is connected to bare
metal and never to a painted or non-metal surface. The wrist strap should be secure and in full contact with your skin, and
ensure that you remove all jewelry such as watches, bracelets, or rings prior to bonding yourself and the equipment.
Electrostatic discharge—ESD protection
ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards,
processors, memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such
as intermittent problems or a shortened product life span. As the industry pushes for lower power requirements and increased
density, ESD protection is an increasing concern.
Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than
in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.
Two recognized types of ESD damage are catastrophic and intermittent failures.
●Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes
an immediate and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has
received a static shock and immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or
nonfunctional memory.
●Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of
intermittent failures means that most of the time when damage occurs, it is not immediately recognizable. The DIMM
receives a static shock, but the tracing is merely weakened and does not immediately produce outward symptoms related to
the damage. The weakened trace may take weeks or months to melt, and in the meantime may cause degradation of memory
integrity, intermittent memory errors, etc.
The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded")
failure.
Perform the following steps to prevent ESD damage:
●Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do not
provide adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts
with increased sensitivity to ESD damage.
●Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.
●When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static
packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you
discharge static electricity from your body.
●Before transporting a static-sensitive component, place it in an anti-static container or packaging.
ESD field service kit
The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components:
anti-static mat, wrist strap, and bonding wire.
Components of an ESD field service kit
The components of an ESD field service kit are:
●Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an
anti-static mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal
on the system being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly
on the mat. ESD-sensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.
●Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist
and bare metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that
is temporarily placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD
mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never
use wireless wrist straps. Always be aware that the internal wires of a wrist strap are prone to damage from normal wear
and tear, and must be checked regularly with a wrist strap tester in order to avoid accidental ESD hardware damage. It is
recommended to test the wrist strap and bonding wire at least once per week.
8Working inside your computer
●ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored
kit, it is a best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A
wrist strap tester is the best method for doing this test. If you do not have your own wrist strap tester, check with your
regional office to find out if they have one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is
strapped to your wrist and push the button to test. A green LED is lit if the test is successful; a red LED is lit and an alarm
sounds if the test fails.
●Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts
that are insulators and often highly charged.
●Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For
example, deploying the kit for a server environment is different than for a desktop or portable environment. Servers are
typically installed in a rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always
look for a large open flat work area that is free of clutter and large enough to deploy the ESD kit with additional space to
accommodate the type of system that is being repaired. The workspace should also be free of insulators that can cause an
ESD event. On the work area, insulators such as Styrofoam and other plastics should always be moved at least 12 inches or
30 centimeters away from sensitive parts before physically handling any hardware components
●ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded
bags are preferred. However, you should always return the damaged part using the same ESD bag and packaging that the
new part arrived in. The ESD bag should be folded over and taped shut and all the same foam packing material should be
used in the original box that the new part arrived in. ESD-sensitive devices should be removed from packaging only at an
ESD-protected work surface, and parts should never be placed on top of the ESD bag because only the inside of the bag is
shielded. Always place parts in your hand, on the ESD mat, in the system, or inside an anti-static bag.
●Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts
to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.
ESD protection summary
It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static
mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all
insulator parts while performing service and that they use anti-static bags for transporting sensitive components.
Transporting sensitive components
When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place
these parts in anti-static bags for safe transport.
After working inside your computer
About this task
NOTE: Leaving stray or loose screws inside your computer may severely damage your computer.
Steps
1. Replace all screws and ensure that no stray screws remain inside your computer.
2. Connect any external devices, peripherals, or cables you removed before working on your computer.
3. Replace any media cards, discs, or any other parts that you removed before working on your computer.
4. Connect your computer and all attached devices to their electrical outlets.
5. Turn on your computer.
Working inside your computer 9
Removing and installing components
NOTE: The images in this document may differ from your computer depending on the configuration you ordered.
Recommended tools
The procedures in this document may require the following tools:
●Phillips #0 screwdriver
●Plastic scribe
Screw List
The following table shows the screw list and the image of the screws.
Table 1. Screw list
Component Screw type Quantity Image
Base cover Captive screws 7
3-cell battery M2x3 3
4-cell battery M2x3 5
Solid-state drive bracket M2x3 1
WLAN M2x3 1
Left system Fan M2x3 2
Right system Fan M2x3 2
Display cable bracket M2x2.5 1
Display hinge bracket M2x2.5
M2x3
1
4
Input Output board M2x2.5 1
Touchpad bracket M2x2 3
2
10 Removing and installing components
Table 1. Screw list (continued)
Component Screw type Quantity Image
Touchpad M2x2 2
Heatsink assembly Captive screws 4
Power button with fingerprint reader M2x3 1
System board M2x2.5 1
Type-C bracket M2x3 1
Removing and installing components 11
Major components of your system
1. Base cover
12 Removing and installing components
2. Heatsink assembly
3. Right system fan
4. Left system fan
5. Solid-state drive
6. System board
7. Battery
8. Speaker
9. Palmrest and keyboard assembly
10. Display assembly
11. Input Output board
12. Coin-cell battery
13. WLAN card
14. Power button with fingerprint reader
NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These
parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative for
purchase options.
MicroSD-card
Removing the microSD-card
Prerequisites
1. Follow the procedure in before working inside your computer.
About this task
The following image provides a visual representation of the microSD-card removal procedure.
Steps
1. Push the microSD-card to eject it from the slot.
2. Remove the microSD-card from the system.
Removing and installing components 13
Installing the MicroSD-card
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image provides a visual representation of the MicroSD-card installation procedure.
Steps
Insert the microSD-card into its slot until it clicks into place.
Next steps
1. Follow the procedure in after working inside your computer.
Base cover
Removing the base cover
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Enter the service mode.
About this task
The following images indicate the location of the base cover, and provide a visual representation of the removal procedure.
14 Removing and installing components
Removing and installing components 15
Steps
1. Loosen the seven captive screws that secure the base cover to the chassis.
2. Using a plastic scribe, pry open the base cover starting from the recesses located in the U-shaped indents near the hinges at
the top edge of the base cover.
3. Pry open the left, right, and bottom sides of the base cover.
4. Carefully lift and remove the base cover from the chassis.
NOTE: Be careful of the latches while removing the base cover as the latches may break.
Installing the base cover
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following images indicate the location of the base cover, and provide a visual representation of the installation procedure.
16 Removing and installing components
Steps
1. Align and place the base cover on the chassis, and snap the base cover into place.
2. Tighten the seven captive screws to secure the base cover to the chassis.
Next steps
1. Exit the service mode.
2. Install the microSD-card.
3. Follow the procedure in after working inside your computer.
Solid-state drive
Removing the M.2 2230 solid-state drive
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Enter the service mode.
4. Remove the base cover.
About this task
The following image indicates the location of the solid-state drive and provides a visual representation of the removal procedure.
Removing and installing components 17
Steps
1. Open the solid-state drive mylar sheet that covers the solid-state drive.
NOTE: There is a protective mylar sheet covering the solid-state drive. This mylar sheet must be opened in order to
proceed with the removal procedure.
2. Remove the screw (M2x3) that secures the solid-state drive bracket to the system board.
3. Remove the solid-state drive bracket from the system board.
4. Slide and remove the solid-state drive from the M.2 card connector on the system board.
Installing the M.2 2230 solid-state drive
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the solid-state drive and provides a visual representation of the installation
procedure.
18 Removing and installing components
Steps
1. Align the notch on the solid-state drive with the tab on the M.2 card connector.
2. Slide the solid-state drive into the M.2 card connector on the system board.
3. Align and place the solid-state drive bracket.
4. Install the screw (M2x3) that secures the solid-state drive bracket to the system board.
5. Close the solid-state drive mylar sheet to cover the solid-state drive.
NOTE: There is a protective mylar sheet covering the solid-state drive. This mylar sheet must be closed after the
installation procedure.
Next steps
1. Install the base cover.
2. Exit the service mode.
3. Install the microSD-card.
4. Follow the procedure in After working inside your computer.
Removing and installing components 19
Removing the M.2 2280 solid-state drive
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Enter the service mode.
4. Remove the base cover.
About this task
The following image indicates the location of the solid-state drive and provides a visual representation of the removal procedure.
Steps
1. Open the solid-state drive mylar sheet that covers the solid-state drive.
NOTE: There is a protective mylar sheet covering the solid-state drive. This mylar sheet must be opened in order to
proceed with the removal procedure.
2. Remove the single screw (M2x3) that secures the solid-state drive to the system board.
3. Slide and remove the solid-state drive from the M.2 card connector on the system board.
Installing the M.2 2280 solid-state drive
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the solid-state drive and provides a visual representation of the installation
procedure.
20 Removing and installing components
Steps
1. Align the notch on the solid-state drive with the tab on the M.2 card connector.
2. Slide the solid-state drive into the M.2 card connector on the system board.
3. Replace the screw (M2x3) that secures the solid-state drive to the system board.
4. Close the solid-state drive mylar sheet to cover the solid-state drive.
NOTE: There is a protective mylar sheet covering the solid-state drive. This mylar sheet must be closed after the
installation procedure.
Next steps
1. Install the base cover.
2. Exit the service mode.
3. Install the microSD-card.
4. Follow the procedure in After working inside your computer.
Speakers
Removing the speakers
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Enter the service mode.
4. Remove the base cover.
About this task
The following image indicates the location of the speakers and provides a visual representation of the removal procedure.
Removing and installing components 21
Steps
1. Disconnect the speaker cable from the connector on the system board.
2. Unroute the speaker cable from the routing guide.
3. Peel the adhesive tapes that secure the speakers in place.
4. Remove the speakers from the chassis.
Installing the speakers
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the speakers and provides a visual representation of the installation procedure.
22 Removing and installing components
Steps
1. Align and place the speakers in the slot on the chassis.
2. Route the speaker cables through the routing guide.
3. Connect the speaker cable to the connector.
4. Adhere the adhesive tapes to secure the speakers in place.
Next steps
1. Install the battery.
2. Install the base cover.
3. Install the microSD-card.
4. Follow the procedure in after working inside your computer.
WLAN card
Removing the WLAN card
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Enter the service mode.
4. Remove the base cover.
About this task
The following images indicate the location of the WWAN card and provide a visual representation of the removal procedure.
Removing and installing components 23
Steps
1. Remove the screw (M2x3) that secures WLAN card bracket to the system board.
2. Lift the WLAN card bracket out of the system.
3. Disconnect the antenna cables from the connectors on the WLAN card.
4. Lift and remove the WLAN card from the WLAN card slot.
Installing the WLAN card
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the WWAN card and provides a visual representation of the installation procedure.
24 Removing and installing components
Steps
1. Align the notch on the WLAN card with the tab on the WLAN card slot.
2. Slide the WLAN card at an angle into the WLAN card slot.
3. Connect the antenna cables to the connectors on the WLAN card.
NOTE: The antenna cable connectors are fragile and utmost care should be taken while replacing them.
Table 2. Antenna cable guide
Cable color Connector
White cable (Main) White triangle (△) on the WLAN module of the system board
Black cable (Aux) Solid triangle (▲) on the WLAN module of the system board
4. Align and place the WLAN card bracket on the WLAN card.
5. Install the screw (M2x3) to secure the WLAN card bracket to the system board.
Next steps
1. Install the base cover.
2. Exit the service mode.
Removing and installing components 25
3. Install the microSD-card.
4. Follow the procedure in After working inside your computer.
Coin-cell battery
Removing the coin-cell battery
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Enter the service mode.
4. Remove the base cover.
About this task
The following image indicates the location of the coin-cell battery and provides a visual representation of the removal procedure.
Steps
1. Disconnect the coin-cell battery cable from the connector on the system board.
2. Lift and remove the coin-cell battery from the palmrest assembly.
Installing the coin-cell battery
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the coin-cell battery and provides a visual representation of the installation
procedure.
26 Removing and installing components
Steps
1. Align and place the coin-cell battery on the palmrest assembly.
2. Connect the coin-cell battery cable to the connector on the system board.
Next steps
1. Install the base cover.
2. Exit the service mode.
3. Install the microSD-card.
4. Follow the procedure in after working inside your computer.
Battery cable
Installing the battery cable
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the battery cable and provides a visual representation of the installation procedure.
Removing and installing components 27
Steps
1. Connect the battery cable to the connector on the battery and adhere the adhesive tape.
2. Route the battery cable through the routing channel in the battery and adhere the adhesive tapes.
3. Connect the battery cable to the connector on the system board.
Next steps
1. Install the base cover.
2. Install the microSD-card.
3. Follow the procedure in After working on your computer.
Removing the battery cable
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Remove the base cover.
About this task
The following image indicates the location of the battery cable and provides a visual representation of the installation procedure.
28 Removing and installing components
Steps
1. Disconnect the battery cable from the connector on the system board.
2. Peel the adhesive tapes and unroute the battery cable from routing channel in the battery.
3. Peel the adhesive tape and disconnect the battery cable from the connector on the battery.
Battery
Removing the 3-cell battery
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Remove the base cover.
NOTE: If battery was disconnected from system board for service, there will be a delay during system boot-up as the
system undergoes RTC battery reset.
About this task
The following image indicates the location of the battery and provide a visual representation of the removal procedure.
Removing and installing components 29
Steps
1. Peel the adhesive tapes that secure the battery in place.
2. Peel the secure-in tape that secures the battery cable to the connector on the system board.
3. Unroute the battery cable from the routing channels between the system board and 3-cell battery.
4. Remove the three (M2x3) screws that secure the battery to the palmrest assembly.
5. Carefully lift and remove the battery from the chassis.
NOTE: Be careful while removing the battery as the battery cable must be disconnected from the connector after the
battery is removed from the system.
6. Disconnect the battery cable from the connector on the system board.
Installing the 3-cell battery
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the battery and provides a visual representation of the installation procedure.
NOTE: If battery was disconnected from system board for service, there will be a delay during system boot-up as the
system undergoes RTC battery reset.
30 Removing and installing components
Steps
1. Connect the battery cable to the connector on the system board.
2. Adhere the secure-in tape to secure the battery cable to the connector on the system board.
3. Route the battery cable through the routing channels between the system board and 3-cell battery.
4. Align and place the battery in the slot on the chassis.
5. Install the three (M2x3) screws to secure the battery in place.
6. Adhere the adhesive tapes to secure the battery in place.
Next steps
1. Install the base cover.
2. Install the microSD-card.
3. Follow the procedure in After working on your computer.
Removing the 4-cell battery
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Remove the base cover.
NOTE: If battery was disconnected from system board for service, there will be a delay during system boot-up as the
system undergoes RTC battery reset.
About this task
The following image indicates the location of the battery and provides a visual representation of the removal procedure.
Removing and installing components 31
Steps
1. Peel the adhesive tapes that secure the battery in place.
2. Peel the secure-in tape that secures the battery cable to the connector on the system board.
3. Unroute the battery cable from the routing channels between the system board and 4-cell battery.
4. Remove the five (M2x3) screws that secure the battery to the palmrest assembly.
5. Carefully lift and remove the battery from the chassis.
NOTE: Be careful while removing the battery as the battery cable must be disconnected from the connector after the
battery is removed from the system.
6. Disconnect the battery cable from the connector on the system board.
Installing the 4-cell battery
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the battery and provides a visual representation of the installation procedure.
NOTE: If battery was disconnected from system board for service, there will be a delay during system boot-up as the
system undergoes RTC battery reset.
32 Removing and installing components
Steps
1. Connect the battery cable to the connector on the system board.
2. Adhere the secure-in tape to secure the battery cable to the connector on the system board.
3. Route the battery cable through the routing channels between the system board and 4-cell battery.
4. Align and place the battery in the slot on the chassis.
5. Install the five (M2x3) screws to secure the battery in place.
6. Adhere the adhesive tapes to secure the battery in place.
Next steps
1. Install the base cover.
2. Install the microSD-card.
3. Follow the procedure in After working on your computer.
System fan
Removing the left system fan
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Remove the base cover.
4. Remove the battery.
About this task
The following image indicates the location of the left system fan and provides a visual representation of the removal procedure.
Removing and installing components 33
Steps
1. Disconnect the system fan cable from the connector on the system board.
2. Remove the two (M2x3) screws that secure the system fan in place.
3. Lift the system fan off the palmrest assembly.
Installing the left system fan
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the left system fan and provides a visual representation of the installation
procedure.
34 Removing and installing components
Steps
1. Align and place the system fan onto the palmrest assembly.
2. Install the two (M2x3) screws that secure the system fan in place.
3. Connect the system fan cable to the connector on the system board.
Next steps
1. Install the battery.
2. Install the base cover.
3. Install the microSD-card.
4. Follow the procedure in after working inside your computer.
Removing the right system fan
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Remove the base cover.
4. Remove the battery.
About this task
The following image indicates the location of the right system fan and provides a visual representation of the removal procedure.
Removing and installing components 35
Steps
1. For visibility, open the solid-state drive mylar sheet that covers the solid-state drive.
2. Disconnect the system fan cable from the connector on the system board.
3. Remove the two (M2x3) screws that secure the system fan in place.
4. Lift the system fan off the palmrest assembly.
Installing the right system fan
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the right system fan and provides a visual representation of the installation
procedure.
36 Removing and installing components
Steps
1. Align and place the system fan onto the palmrest assembly.
2. Install the two (M2x3) screws that secure the system fan in place.
3. Connect the system fan cable to the connector on the system board.
4. Close the solid-state drive mylar sheet to cover the solid-state drive.
Next steps
1. Install the battery.
2. Install the base cover.
3. Install the microSD-card.
4. Follow the procedure in after working inside your computer.
Removing and installing components 37
Display assembly
Removing the display assembly
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Enter the service mode.
4. Remove the base cover.
About this task
The following images indicate the location of the display assembly and provide a visual representation of the removal procedure.
NOTE: The display assembly removal procedure is the same for both laptop and convertible chassis.
38 Removing and installing components
Steps
1. Remove the (M2x2.5) screw that secures the display cable bracket. Remove the display cable bracket.
2. Disconnect the display cable from the connector on the system board.
3. Peel the adhesive tape that secures the display cable.
4. Remove the (M2x2.5) screw and four (M2x3) screws that secure the display hinges to the system.
5. Lift the left and right hinges in upward direction away from the system.
6. Lift the display assembly off the system.
Removing and installing components 39
After performing the preceding steps, you are left with the display assembly.
Installing the display assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
NOTE: The display assembly installation procedure is the same for both laptop and convertible chassis.
About this task
The following images indicate the location of the display assembly and provide a visual representation of the installation
procedure.
40 Removing and installing components
Removing and installing components 41
Steps
1. Align and place the system chassis under the hinges of the display assembly.
2. Install the (M2x2.5) screw and four (M2x3) screws that secure the display hinges to the system.
3. Connect the display cable to its connector on the system board. Adhere the adhesive tape to secure the display cable.
4. Align and place the display cable bracket in place.
5. Install the (M2x2.5) screw to secure the display cable bracket.
Next steps
1. Install the base cover.
2. Exit the service mode.
3. Install the microSD-card.
4. Follow the procedure in after working inside your computer.
Input Output board
Removing the Input Output board
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Enter the service mode.
4. Remove the base cover.
About this task
The following image indicates the location of the Input Output board and provides a visual representation of the removal
procedure.
42 Removing and installing components
Steps
1. Remove the two (M2x3) screws that secure the left display hinge to the system.
2. Lift the left hinge in upward direction away from the system.
3. Open the latch and disconnect the Input Output board cable from the connector on the Input Output board.
4. Remove the (M2x2.5) screw that secures the Input Output board to the palmrest assembly.
5. Lift the Input Output board off the palmrest assembly.
Installing the Input Output board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the I/O board and provides a visual representation of the installation procedure.
Removing and installing components 43
Steps
1. Align and place the Input Output board on the palmrest assembly.
2. Install the (M2x2.5) screw to secure the Input Output board to the palmrest assembly.
3. Connect the Input Output board cable to the connector on the Input Output board and close its latch.
4. Gently press the left hinge in downward direction toward the system.
5. Install the two (M2x3) screws to secure the left display hinge to the system.
Next steps
1. Install the base cover.
2. Exit the service mode.
3. Install the microSD-card.
4. Follow the procedure in after working inside your computer.
Heatsink assembly
Removing the heatsink assembly
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Enter the service mode.
4. Remove the base cover.
44 Removing and installing components
About this task
The following image indicates the location of the heatsink assembly and provides a visual representation of the removal
procedure.
Steps
1. For visibility, open the solid-state drive mylar sheet that covers the solid-state drive.
2. Loosen the four captive screws (in reverse order, 4->3->2->1) that secure the heatsink assembly to the system board.
3. Slide, lift and remove the heatsink assembly from the system board.
Installing the heatsink assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the heatsink assembly and provides a visual representation of the installation
procedure.
Removing and installing components 45
Steps
1. Align and place the heatsink assembly into the slot on the system board.
2. Tighten the four captive screws to secure the heatsink assembly to the system board.
3. Close the solid-state drive mylar sheet to cover the solid-state drive.
Next steps
1. Install the base cover.
2. Exit the service mode.
3. Install the microSD-card.
4. Follow the procedure in after working inside your computer.
Touchpad
Removing the touchpad
Prerequisites
1. Follow the procedure in before working inside your computer.
46 Removing and installing components
2. Remove the microSD-card.
3. Remove the base cover.
4. Remove the battery.
About this task
The following image indicates the location of the touchpad and provides a visual representation of the removal procedure.
Steps
1. Open the latch and disconnect the touchpad cable from the connector on the system board.
2. Remove the three (M2x2) screws that secure the touchpad bracket to the touchpad module.
3. Lift and remove the touchpad bracket from the touchpad module.
4. Remove the two (M2x2) screws that secure the touchpad module to the palmrest assembly.
5. Lift and remove the touchpad module from the palmrest assembly.
Installing the touchpad
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the touchpad and provides a visual representation of the installation procedure.
Removing and installing components 47
Steps
1. Align and place the touchpad module into the slot on the palmrest assembly.
2. Install the two (M2x2) screws to secure the touchpad module to the palmrest assembly.
3. Align and place the touchpad bracket on the touchpad module.
4. Install the three (M2x2) screws to secure the touchpad bracket to the touchpad module.
5. Connect the touchpad cable to the connector on the system board and close the latch.
Next steps
1. Install the battery.
2. Install the base cover.
3. Install the microSD-card.
4. Follow the procedure in after working inside your computer.
Power-button board
Removing the power-button board
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Enter the service mode.
4. Remove the base cover.
5. Remove the display assembly.
6. Remove the input output board.
7. Remove the heatsink assembly.
About this task
The following image indicates the location of the power-button board and provides a visual representation of the removal
procedure.
48 Removing and installing components
Steps
1. Open the latch and disconnect the power-button board cable from the connector on the system board.
2. Remove the (M2x3) screw that secures the power-button board to the chassis.
3. Remove the power-button board from the chassis.
Installing the power-button board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the power-button board and provides a visual representation of the installation
procedure.
Removing and installing components 49
Steps
1. Align and place the power-button board on the chassis.
2. Install the (M2x3) screw to secure the power-button board to the chassis.
3. Connect thepower-button board cable to the connector on the system board and close its latch.
Next steps
1. Install the heatsink assembly.
2. Install the input output board.
3. Install the display assembly.
4. Install the base cover.
5. Exit the service mode.
6. Install the microSD-card.
7. Follow the procedure in after working inside your computer.
System board
Removing the system board
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Enter the service mode.
4. Remove the base cover.
5. Remove the speaker.
6. Remove the M.2 solid-state drive.
7. Remove the system fan.
8. Remove the display assembly.
9. Remove the input output board.
50 Removing and installing components
10. Remove the heatsink assembly.
11. Remove the power button with fingerprint reader.
About this task
The following image indicates the connectors on your system board.
Figure 1. System-board connectors
1. Power button with fingerprint reader cable 2. Speaker cable
3. Display cable 4. Power cable
5. Backlit LED cable 6. Keyboard cable
7. Touchpad cable 8. Coin-cell battery cable
9. Input output board cable
The following images indicate the location of the system board assembly and provide a visual representation of the removal
procedure.
Removing and installing components 51
Steps
1. Open the latch and disconnect the touchpad cable, keyboard cable and LED cable from the connectors on the system board.
2. Disconnect the power cable, power button with finger print reader cable, speaker cable, and coin-cell battery cable from the
connectors on the system board.
3. Open the latch and pull the input output board cable from the connector on the system board.
4. Remove the (M2x2.5) screw that secures the system board in place.
52 Removing and installing components
5. Remove the (M2x3) screw that secures the type-c bracket in place.
6. Lift and remove the system board from the system.
7. Lift and remove the type-c bracket from the system.
Installing the system board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the connectors on your system board.
Figure 2. System-board connectors
1. Power button with fingerprint reader cable 2. Speaker cable
3. Display cable 4. Power cable
5. Backlit LED cable 6. Keyboard cable
7. Touchpad cable 8. Coin-cell battery cable
9. Input output board cable
The following images indicate the location of the system board and provide a visual representation of the installation procedure.
Removing and installing components 53
54 Removing and installing components
Steps
1. Align and place the type-c bracket on the system board.
NOTE: The type-c bracket must be installed on the system board before installing the system board into the palmrest
assembly. Technicians cannot install the Type-c bracket once the system board is assembled into the palmrest assembly.
2. Align and place the system board on the chassis.
3. Install the (M2x3) screw to secure the type-c bracket in place.
4. Install the (M2x2.5) screw to secure the system board in place.
5. Connect the input output board cable to the connector on the system board and close the latch.
6. Connect the power cable, power button with finger print reader cable, speaker cable, and coin-cell battery cable to the
connectors on the system board.
7. Connect the touchpad cable, keyboard cable, and LED cable to the connectors on the system board and close the latch.
Next steps
1. Install the power button with fingerprint reader.
2. Install the heatsink assembly.
3. Install the input output board.
4. Install the display assembly.
5. Install the system fan.
6. Install the M.2 solid-state drive.
7. Install the speakers.
8. Install the base cover.
9. Exit the service mode.
10. Install the microSD-card.
11. Follow the procedure in after working inside your computer.
Removing and installing components 55
Power adapter port
Removing the power adapter port
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Enter the service mode.
4. Remove the base cover.
5. Remove the speaker.
6. Remove the M.2 solid-state drive.
7. Remove the system fan.
8. Remove the display assembly.
9. Remove the input output board.
10. Remove the heatsink assembly.
11. Remove the power button with fingerprint reader.
12. Remove the system board.
NOTE: The system board can be removed with the heat sink attached.
About this task
The following image indicates the location of the power adapter port and provides a visual representation of the removal
procedure.
Steps
Remove the power adapter port from the chassis.
56 Removing and installing components
Installing the power adapter port
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The following image indicates the location of the power adapter port and provides a visual representation of the installation
procedure.
Steps
Align and place the power adapter port on the chassis.
Next steps
1. Install the system board.
NOTE: The system board can be installed with the heat sink attached.
2. Install the power button with fingerprint reader.
3. Install the heatsink assembly.
4. Install the input output board.
5. Install the display assembly.
6. Install the system fan.
7. Install the M.2 solid-state drive.
8. Install the speakers.
9. Install the base cover.
10. Exit the service mode.
11. Install the microSD-card.
12. Follow the procedure in after working inside your computer.
Removing and installing components 57
Palmrest assembly
Removing the palmrest assembly
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD-card.
3. Remove the base cover.
4. Remove the battery.
5. Remove the speaker.
6. Remove the M.2 solid-state drive.
7. Remove the system fan.
8. Remove the display assembly.
9. Remove the input output board.
10. Remove the heatsink assembly.
11. Remove the touchpad.
12. Remove the power button with fingerprint reader.
13. Remove the system board.
NOTE: The system board can be removed with the heat sink attached.
About this task
The following image indicates the location of the palmrest and provides a visual representation of the removal procedure.
Steps
After performing the preceding steps, you are left with the palmrest assembly.
Next steps
1. Install the system board.
NOTE: The system board can be installed with the heat sink attached.
58 Removing and installing components
2. Install the power button with fingerprint reader.
3. Install the heatsink assembly.
4. Install the touchpad.
5. Install the input output board.
6. Install the display assembly.
7. Install the system fan.
8. Install the M.2 solid-state drive.
9. Install the speakers.
10. Install the battery.
11. Install the base cover.
12. Install the microSD-card.
13. Follow the procedure in after working inside your computer.
Removing and installing components 59
System setup
CAUTION: Unless you are an expert computer user, do not change the settings in the BIOS Setup program.
Certain changes can make your computer work incorrectly.
NOTE: Before you change BIOS Setup program, it is recommended that you write down the BIOS Setup program screen
information for future reference.
Use the BIOS Setup program for the following purposes:
●Get information about the hardware installed in your computer, such as the amount of RAM and the size of the hard drive.
●Change the system configuration information.
●Set or change a user-selectable option, such as the user password, type of hard drive installed, and enabling or disabling
base devices.
Boot menu
To initiate a one-time boot menu with a list of the valid boot devices for the system, press <F12> when the Dell logo is displayed.
Diagnostics and BIOS Setup options are also in this menu. The devices that are listed on the boot menu depend on the bootable
devices in the system. This menu is useful when you are attempting to boot to a particular device or to bring up the diagnostics
for the system. Using the boot menu, do not change the boot order that is stored in the BIOS.
The options are:
●Legacy External Device Boot
○Onboard NIC
●UEFI Boot:
○UEFI: TOSHIBA MQ01ACF050
●Other Options:
○BIOS Setup
○Device Configuration
○BIOS Flash Update
○Diagnostics
○Intel (R) Management Engine BIOS Extension (MEBx)
○Change Boot Mode Settings
Boot Sequence
Boot sequence enables you to bypass the System Setup–defined boot device order and boot directly to a specific device (for
example: optical drive or hard drive). During the Power-on Self-Test (POST), when the Dell logo appears, you can:
●Access System Setup by pressing F2 key
●Bring up the one-time boot menu by pressing F12 key.
The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot menu options
are:
●Removable Drive (if available)
●STXXXX Drive
NOTE: XXXX denotes the SATA drive number.
●Optical Drive (if available)
●SATA Hard Drive (if available)
●Diagnostics
NOTE: Choosing Diagnostics, displays the SupportAssist screen.
4
System setup 61
The boot sequence screen also displays the option to access the System Setup screen.
Navigation keys
NOTE: For most of the System Setup options, changes that you make are recorded but do not take effect until you restart
the system.
Keys Navigation
Up arrow Moves to the previous field.
Down arrow Moves to the next field.
Enter Selects a value in the selected field (if applicable) or follow the link in the field.
Spacebar Expands or collapses a drop-down list, if applicable.
Tab Moves to the next focus area.
Esc Moves to the previous page until you view the main screen. Pressing Esc in the main screen displays a
message that prompts you to save any unsaved changes and restarts the system.
System setup options
NOTE: Depending on your system and its installed devices, the items that are listed in this section may or may not appear.
Table 3. System setup options—System information menu
Overview
Lattitude 3320
BIOS Version Displays the BIOS version number.
Service Tag Displays the Service Tag of the system.
Asset Tag Displays the Asset Tag of the system.
Manufacture Date Displays the manufacture date of the system.
Ownership Date Displays the ownership date of the system.
Express Service Code Displays the express service code of the system.
Ownership Tag Displays the Ownership Tag of the system.
Signed Firmware Update Displays whether the Signed Firmware Update is enabled on your system.
Battery Information
Primary Displays that battery is primary.
Battery Level Displays the battery level of the system.
Battery State Displays the battery state of the system.
Health Displays the battery health of the system.
AC Adapter Displays whether the AC adapter is connected or not.
Processor Information
Processor Type Displays the processor type.
Maximum Clock Speed Displays the maximum processor clock speed.
Minimum Clock Speed Displays the minimum processor clock speed.
Current Clock Speed Displays the current processor clock speed.
Core Count Displays the number of cores on the processor.
62 System setup
Table 3. System setup options—System information menu (continued)
Overview
Processor ID Displays the processor identification code.
Processor L2 Cache Displays the processor L2 Cache size.
Processor L3 Cache Displays the processor L3 Cache size.
Microcode Version Displays the microcode version.
Intel Hyper-Threading Capable Displays whether the processor is Hyper-Threading (HT) capable.
64-Bit Technology Displays whether 64-bit technology is used.
Memory Information
Memory Installed Displays the total system memory installed.
Memory Available Displays the total system memory available.
Memory Speed Displays the memory speed.
Memory Channel Mode Displays single or dual channel mode.
Memory Technology Displays the technology that is used for the memory.
Devices Information
Panel Type Displays the Panel Type of the system.
Video Controller Displays the video controller type of the system.
Video Memory Displays the video memory information of the system.
Wi-Fi Device Displays the wireless device information of the system.
Native Resolution Displays the native resolution of the system.
Video BIOS Version Displays the video BIOS version of the system.
Audio Controller Displays the audio controller information of the system.
Bluetooth Device Displays the Bluetooth device information of the system.
Table 4. System setup options—Boot Configuration menu
Boot Configuration
Boot Sequence
Boot mode Displays the boot mode.
Boot Sequence Displays the boot sequence.
Secure Digital (SD) Card Boot Enable or disable the SD card read-only boot.
By default, the Secure Digital (SD) Card Boot option is not enabled.
Secure Boot
Enable Secure Boot Enable or disable the secure boot feature.
By default, the option is not enabled.
Secure Boot Mode Enable or disable to change the secure boot mode options.
By default, the Deployed Mode is enabled.
Expert Key Management
Enable Custom Mode Enable or disable custom mode.
By default, the custom mode option is not enabled.
Custom Mode Key Management Select the custom values for expert key management.
System setup 63
Table 5. System setup options—Integrated Devices menu
Integrated Devices
Date/Time Displays the current date in MM/DD/YYYY format and current time in
HH:MM:SS AM/PM format.
Camera Enables or disable the camera.
By default, the Enable Camera option is selected
Audio
Enable Audio Enable or disable the integrated audio controller.
By default, all the options are enabled.
USB Configuration ●Enable or disable booting from USB mass storage devices that are
connected to external USB ports.
By default, the Enable External USB Ports option is enabled.
●Enable or disable booting from USB mass storage devices such as external
hard drive, optical drive, and USB drive.
By default, the Enable USB Boot Support option is enabled.
Disable USB4 PCIE Tunneling Disable the USB4 PCIE Tunneling option.
By default, the option is disabled.
Video/Power only on Type-C Ports Enable or disable the Type-C port functionality to video or power only.
By default, the Video/Power only on Type-C Ports option is disabled.
Table 6. System setup options—Storage menu
Storage
SATA/NVMe Operation
SATA/NVMe Operation Set the operating mode of the integrated storage device controller.
By default, the RAID On option is enabled.
Storage interface
Port Enablement This page allows you to enable the onboard drives.
By default, the M.2 PCIe SSD option is enabled.
SMART Reporting
Enable SMART Reporting Enable or disable Self-Monitoring, Analysis, and Reporting Technology
(SMART) during system startup.
By default, the Enable SMART Reporting option is not enabled.
Drive Information
M.2 PCIe SSD
Type Displays the M.2 PCIe SSD type information of the system.
Device Displays the M.2 PCIe SSD device information of the system.
Enable MediaCard
Secure Digital (SD) Card Enable or disable the SD card.
By default, the Secure Digital (SD) Card option is enabled.
Secure Digital (SD) Card Read-Only Mode Enable or disable the SD card read-only mode.
By default, the Secure Digital (SD) Card Read-Only Mode option is not
enabled.
64 System setup
Table 7. System setup options—Display menu
Display
Display Brightness
Brightness on battery power Enable to set screen brightness when the system is running on battery power.
Brightness on AC power Enable to set screen brightness when the system is running on AC power.
EcoPower Enable or disable EcoPower Feature in your panel. EcoPower can increase
the battery life of your system by reducing the display brightness when
appropriate.
By default, Enable EcoPower option is enabled.
Full Screen Logo Enable or disable full screen logo.
By default, the option is not enabled.
Table 8. System setup options—Connection menu
Connection
Wireless Device Enable
WLAN Enable or disable the internal WLAN device.
By default, the option enabled.
Bluetooth Enable or disable the internal Bluetooth device
By default, the option enabled.
Enable UEFI Network Stack Enable or disable UEFI Network Stack and controls the on-board LAN
Controller.
By default, the Enable UEFI Network Stack option is enabled.
HTTPs Boot Feature
HTTPs Boot Enable or disable the HTTPs Boot feature.
By default, the HTTPs Boot option is disabled.
Table 9. System setup options—Power menu
Power
Battery configuration Enables the system to run on battery during peak power usage hours. Use the
table Custom Charge Start and Custom Charge Stop, to prevent AC power
usage between certain times of each day.
By default, the Adaptive option is enabled.
Advanced Configuration
Enable Advanced Battery Charge
Configuration
Enable or disable the advanced battery charge configuration.
By default, the Enable Advanced Battery Charge Configuration option is
disabled.
Peak Shift Enables the system to run on battery during peak power usage hours.
Enable Peak Shift By default, the Enable Peak Shift option is disabled.
Thermal Management Enables to cool the fan and processor heat management to adjust the system
performance, noise, and temperature.
By default, the Optimized option is enabled.
USB Wake Support
Enable USB Wake Support When enabled, the USB devices like a mouse or keyboard can be used to wake
the system from Standby, Hibernate, and Power Off.
System setup 65
Table 9. System setup options—Power menu (continued)
Power
NOTE: This feature requires Deep Sleep Control to be disabled.
NOTE: This feature is only functional when the AC power adapter is
connected. If the AC power adapter is removed before Standby, the BIOS
will remove power from all of the USB ports to conserve battery power.
By default, the Enable USB Wake Support option is disabled.
Wake on Dell USB-C Dock When enabled, connecting a Dell USB-C Dock will wake the system from
Standby, Hibernate, and Power Off.
By default, the Wake on Dell USB-C Dock option is enabled.
Block Sleep Enables to block entering sleep (S3) mode in the operating system.
By default, the Block Sleep option is disabled.
Lid Switch
Enabled Lid Switch Enable or disable the lid switch.
By default, the Enable Lid Switch option is enabled.
Power On Lid Open When enabled, allows the system to power up from the off state whenever the
lid is opened.
By default, the Power On Lid Open option is enabled.
Intel Speed Shift Technology Enable or disable the Intel speed shift technology support.
By default, the Intel Speed Shift Technology option is enabled.
Table 10. System setup options—Security menu
Security
TPM 2.0 Security
TPM 2.0 Security On Allows you to enable or disable TPM visibility to operating system.
By default, the TPM 2.0 Security On option is enabled.
Attestation Enable Enables to control whether the Trusted Platform Module (TPM) Endorsement
Hierarchy is available to the operating system.
By default, the Attestation Enable option is enabled.
Key Storage Enable Enables to control whether the Trusted Platform Module (TPM) Storage
Hierarchy is available to the operating system.
By default, the Key Storage Enable option is enabled.
SHA-256 When enabled, the BIOS and TPM will use the SHA-256 hash algorithm to
extend measurements into the TPM PCRs during BIOS boot.
By default, the SHA-256 option is enabled.
Clear Enables to clear the TPM owner information and returns the TPM to the
default state.
By default, the Clear option is disabled.
PPI Bypass for Clear Commands Controls the TPM Physical Presence Interface (PPI).
By default, the PPI ByPass for clear Commands option is disabled.
SMM Security Mitigation Enable or disable additional UEFI SMM Security Mitigation protections.
By default, the option is enabled.
Data Wipe on Next Boot
66 System setup
Table 10. System setup options—Security menu (continued)
Security
Start Data Wipe Enable or disable the data wipe on next boot.
By default, the Start Data Wipe option is disabled.
Absolute Enable or disable or permanently disable the BIOS module interface of the
optional Absolute Persistence Module service from Absolute software.
By default, the option is enabled.
WARNING: The 'Permanently Disabled' option can only be
selected once. When 'Permanently Disabled' is selected, Absolute
Persistence cannot be re-enabled. No further changes to the
Enable/Disable states are allowed.
NOTE: The Enable/Disable options will be unavailable while Computrace is
in the activated state.
UEFI Boot Path Security Controls whether the system will prompt the user to enter the admin password
(if set) when booting to a UEFI boot path device from the F12 boot menu.
By default, the Always Except Internal HDD option is enabled.
Table 11. System setup options—Passwords menu
Passwords
Admin Password Set, change, or delete the administrator password.
System Password Set, change, or delete the system password.
NVMe SSD0 Set, change, or delete the NVMe SSD0 password.
Password Configuration
Upper Case Letter Reinforces password must have at least one upper case letter.
By default, the option is disabled.
Lower Case Letter Reinforces password must have at least one lower case letter.
By default, the option is disabled.
Digit Reinforces password must have at least one digit number.
By default, the option is disabled.
Special Character Reinforces password must have at least one special character.
By default, the option is disabled.
Minimum Characters Set the minimum characters allowed for password.
Password Bypass When enabled, this always prompts for system and internal hard drive
passwords when powered on from the off state.
By default, the Disabled option is selected.
Password Changes
Enable Non-Admin Password Changes Enable or disable to change system and hard drive password without the need
for admin password.
By default, the option is enabled.
Admin Setup Lockout
Enable Admin Setup Lockout Enables administrators control over how their users can or cannot access BIOS
setup.
By default, the option is disabled.
System setup 67
Table 11. System setup options—Passwords menu (continued)
Passwords
Master Password Lockout
Enable Master Password Lockout When enabled, this disables the master password support.
By default, the option is disabled.
Allow Non-Admin PSID Revert
Enable Allow Non-Admin PSID Revert Controls access to the Physical Security ID (PSID) revert of NVMe hard-drives
from the Dell Security Manager prompt.
By default, the option is disabled.
Table 12. System setup options—Update, Recovery menu
Update, Recovery
UEFI Capsule Firmware Updates Enable or disable BIOS updates through UEFI capsule update packages.
NOTE: Disabling this option will block BIOS updates from services such as
Microsoft Windows Update and Linux Vendor Firmware Service (LVFS).
By default, the option is enabled.
BIOS Recovery from Hard Drive Enables the user to recover from certain corrupted BIOS conditions from a
recovery file on the user primary hard drive or an external USB key.
By default, the option is enabled.
NOTE: BIOS Recovery from Hard Drive is not available for self-encrypting
drives (SED).
BIOS Downgrade
Allow BIOS Downgrade This field controls the flashing of the system firmware to previous revisions.
By default, the option is enabled.
SupportAssist OS Recovery Enable or disable the boot flow for SupportAssist OS Recovery tool in the
event of certain system errors.
By default, the option is enabled.
BIOSConnect Enable or disable cloud Service operating system recovery if the main operating
system fails to boot with the number of failures equal to or greater than the
value specified by the Auto operating system Recovery Threshold setup option
and local Service operating system does not boot or is not installed.
By default, the option is enabled.
Dell Auto operating system Recovery
Threshold
Controls the automatic boot flow for SupportAssist System Resolution Console
and for Dell operating system Recovery Tool.
By default, the threshold value is set to 2.
Table 13. System setup options—System Management menu
System Management
Service Tag Displays the Service Tag of the system.
Asset Tag Create a system Asset Tag.
AC Behavior
Wake on AC Enable or disable the wake on AC option.
By default, the option is disabled.
68 System setup
Table 13. System setup options—System Management menu (continued)
System Management
Auto on Time Enable to set the system to turn on automatically every day or on a preselected
date and time. This option can be configured only if the Auto On Time is set to
Everyday, Weekdays, or Selected Days.
By default, the option is disabled.
Table 14. System setup options—Keyboard menu
Keyboard
Numlock Enable Allows you to enable or disable the Numlock function when the system boots.
By default, the option Fn Lock Options is enabled.
Fn Lock Options By default, the Fn lock option is enabled.
Lock Mode By default, the Lock Mode Secondary option is enabled. With this option, the
F1-F2 keys scan the code for their secondary functions.
Table 15. System setup options—Pre-boot Behavior menu
Pre-boot Behavior
Adapter Warnings
Enable Adapter Warnings Enable or disable the warning messages during boot when the adapters with
less power capacity are detected.
By default, the option is enabled.
Warning and Errors Enable or disable the action to be done when a warning or error is encountered.
By default, the Prompt on Warnings and Errors option is enabled.
USB-C Warnings
Enable Dock Warning Messages By default, the option is enabled.
Fastboot Allows you to configure the speed of the UEFI boot process.
By default, the Minimal option is enabled.
Extend BIOS POST Time Set the BIOS POST load time.
By default, the 0 seconds option is enabled.
Table 16. System setup options—Virtualization menu
Virtualization
Intel Virtualization Technology
Enable Intel Virtualization Technology
(VT)
When enabled, the system will be able to run a Virtual Machine Monitor
(VMM).
By default, the option is enabled.
VT for Direct I/O When enabled, the system will be able to perform Virtualization Technology for
Direct I/O (VT-d).
By default, the option is enabled.
Intel Trusted Execution Technology
(TXT)
Enable Intel Trusted Execution
Technology (TXT)
Specifies whether a measured Virtual Machine Monitor (MVMM) can use the
additional hardware capabilities that are provided by Intel Trusted Execution
Technology. The following must be enabled in order to enable Intel TXT.
●Trusted Platform Module (TPM)
System setup 69
Table 16. System setup options—Virtualization menu (continued)
Virtualization
●Intel Hyper-Threading
●All CPU cores (Multi-Core Support)
●Intel Virtualization Technology
●Intel VT for Direct I/O
By default, the option is disabled.
Table 17. System setup options—Performance menu
Performance
Multi Core Support
Active Cores Enables to change the number of CPU cores available to the operating system.
By default, the All Cores option is enabled.
Intel SpeedStep
Enable Intel SpeedStep Technology Enables the system to dynamically adjust processor voltage and core
frequency, decreasing average power consumption and heat production.
By default, the option is enabled.
C-States Control
Enable C-State Control Enable the ability of the CPU to enter and exit low power state. When disabled,
it disabled all C-states. When enabled, it enabled all C-states that the chipset
or platform allows.
By default, the option is enabled.
Intel Turbo Boost Technology
Enable Intel Turbo Boost Technology Enable or disable the Intel TurboBoost mode of the processor.
By default, the option is enabled.
Intel Hyper-Threading Technology
Enable Intel Hyper-Threading Technology Enable or disable Hyper-Threading in the processor.
By default, the option is enabled.
Dynamic Tuning:Machine Learning
Enable Dynamic Tuning:Machine Learning Enables the operating system capability to enhance dynamic power tuning
capabilities based on detected workloads.
By default, the option is disabled.
Table 18. System setup options—System Logs menu
System Logs
BIOS Event Log
Clear Bios Event Log Displays BIOS events.
By default, the Keep Log option is enabled.
Thermal Event Log
Clear Thermal Event Log Displays Thermal events.
By default, the Keep Log option is enabled.
Power Event Log
Clear Power Event Log Displays power events.
By default, the Keep Log option is enabled.
70 System setup
Table 18. System setup options—System Logs menu (continued)
System Logs
License Information Displays the license information of the system.
Updating the BIOS in Windows
Prerequisites
It is recommended to update your BIOS (System Setup), when you replace the system board or if an update is available. For
laptops, ensure that your computer battery is fully charged and connected to a power outlet.
About this task
NOTE: If BitLocker is enabled, it must be suspended before updating the system BIOS, and then re-enabled after the BIOS
update is completed.
Steps
1. Restart the computer.
2. Go to www.dell.com/support.
●Enter the Service Tag or Express Service Code and click Search.
●Click Drivers & Downloads.
●Click Detect Drivers and follow the on-screen instructions.
3. If you are unable to detect or find the Service Tag, click Browse all products.
4. Choose the appropriate category to reach the product page.
5. Select your computer model, followed by its model number.
NOTE: The Product Support page of your computer appears.
6. Click Drivers & Downloads.
NOTE: The Drivers & Downloads section is displayed.
7. Click Category, and select BIOS from the drop-down list.
8. Click the toggle button Show downloads for only THIS PC XXXXXXX.
NOTE: XXXXXXX denotes the Service Tag.
9. Select the latest BIOS file and click Download.
10. After the download is complete, browse to the folder where you saved the system BIOS executable file.
11. Double-click the system BIOS executable file.
NOTE: Follow the on-screen instructions.
Updating BIOS on systems with BitLocker enabled
CAUTION: If BitLocker is not suspended before updating the BIOS, the next time you reboot the system it
will not recognize the BitLocker key. You will then be prompted to enter the recovery key to progress and the
system will ask for this on each reboot. If the recovery key is not known this can result in data loss or an
unnecessary operating system re-install. For more information on this subject, see Knowledge Article: https://
www.dell.com/support/article/sln153694
System setup 71
Updating your system BIOS using a USB flash drive
About this task
If the computer cannot load into Windows but there is still a need to update the BIOS, download the BIOS file using another
computer and save it to a bootable USB flash drive.
NOTE: You must use a bootable USB flash drive. For more information, see the knowledge base article SLN143196.
Steps
1. Download the BIOS update .exe file to another computer.
2. Copy the .exe file onto the bootable USB flash drive.
3. Insert the USB flash drive into the computer that requires the BIOS update.
4. Restart the computer and press F12 when the Dell logo appears to display the One Time Boot Menu.
5. Using arrow keys, select USB Storage Device and press Enter.
6. The computer restarts to a Diag C:\> prompt.
7. Run the file by typing the complete filename and press Enter.
8. The BIOS Update Utility is displayed. Follow the on-screen instructions.
Figure 3. DOS BIOS Update Screen
System and setup password
Table 19. System and setup password
Password type Description
System password Password that you must enter to log on to your system.
Setup password Password that you must enter to access and make changes to
the BIOS settings of your computer.
You can create a system password and a setup password to secure your computer.
CAUTION: The password features provide a basic level of security for the data on your computer.
CAUTION: Anyone can access the data stored on your computer if it is not locked and left unattended.
72 System setup
NOTE: System and setup password feature is disabled.
Assigning a system setup password
Prerequisites
You can assign a new System or Admin Password only when the status is in Not Set.
About this task
To enter the system setup, press F2 immediately after a power-on or reboot.
Steps
1. In the System BIOS or System Setup screen, select Security and press Enter.
The Security screen is displayed.
2. Select System/Admin Password and create a password in the Enter the new password field.
Use the following guidelines to assign the system password:
●A password can have up to 32 characters.
●The password can contain the numbers 0 through 9.
●Only lower case letters are valid, upper case letters are not allowed.
●Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).
3. Type the system password that you entered earlier in the Confirm new password field and click OK.
4. Press Esc and a message prompts you to save the changes.
5. Press Y to save the changes.
The computer reboots.
Deleting or changing an existing system setup password
Prerequisites
Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing
System and Setup password. You cannot delete or change an existing System or Setup password, if the Password Status is
Locked.
About this task
To enter the System Setup, press F2 immediately after a power-on or reboot.
Steps
1. In the System BIOS or System Setup screen, select System Security and press Enter.
The System Security screen is displayed.
2. In the System Security screen, verify that Password Status is Unlocked.
3. Select System Password, alter or delete the existing system password and press Enter or Tab.
4. Select Setup Password, alter or delete the existing setup password and press Enter or Tab.
NOTE: If you change the System and/or Setup password, re enter the new password when prompted. If you delete the
System and Setup password, confirm the deletion when prompted.
5. Press Esc and a message prompts you to save the changes.
6. Press Y to save the changes and exit from System Setup.
The computer restarts.
System setup 73
Troubleshooting
Built-in self-test (BIST)
About this task
There are three different types of BIST to check the performance of display, power rail, and system board. These tests are
important to evaluate if an LCD or system board needs a replacement.
1. M-BIST: M-BIST is the system board built-in self-test diagnostics tool that improves the diagnostics accuracy of system
board embedded controller (EC) failures. M-BIST must be manually initiated before POST and can also run on a dead
system .
2. L-BIST: L-BIST is an enhancement to the single LED error code diagnostics and is automatically initiated during POST.
3. LCD-BIST: LCD BIST is an enhanced diagnostic test that is introduced through Preboot System Assessment (PSA) on legacy
systems.
Table 20. Functions
M-BIST L-BIST
Purpose Evaluates the health condition of the
system board.
Checks if the system board is supplying
power to the LCD by performing an LCD
Power Rail test.
Trigger Press the <M> key and the power
button.
Integrated into the single LED error
code diagnostics. Automatically initiated
during POST.
Indicator of fault Battery LED light with Solid Amber Battery LED error code of [2,8] blinks
Amber x2, then pause, then blinks White
x8.
Repair instruction Indicates a problem with the system
board.
Indicates a problem with the system
board.
LCD Built-in Self Test (BIST)
Dell laptops have a built-in diagnostic tool that helps you determine if the screen abnormality you are experiencing is an inherent
problem with the LCD (screen) of the Dell laptop or with the video card (GPU) and PC settings.
When you notice screen abnormalities like flickering, distortion, clarity issues, fuzzy or blurry image, horizontal or vertical lines,
color fade etc., it is always a good practice to isolate the LCD (screen) by running the Built-In Self Test (BIST).
How to invoke LCD BIST Test
1. Power off the Dell laptop.
2. Disconnect any peripherals that are connected to the laptop. Connect only the AC adapter (charger) to the laptop.
3. Ensure that the LCD (screen) is clean (no dust particles on the surface of the screen).
4. Press and hold D key and Power on the laptop to enter LCD built-in self test (BIST) mode. Continue to hold the D key, until
you see color bars on the LCD (screen).
5. The screen will display multiple color bars and change colors on the entire screen to red, green, and blue.
6. Carefully inspect the screen for abnormalities.
7. Press Esc key to exit.
5
74 Troubleshooting
NOTE: Dell SupportAssist Pre-boot diagnostics upon launch, initiates an LCD BIST first, expecting a user intervention
confirm functionality of the LCD.
Dell SupportAssist Pre-boot System Performance
Check diagnostics
About this task
SupportAssist diagnostics (also known as system diagnostics) performs a complete check of your hardware. The Dell
SupportAssist Pre-boot System Performance Check diagnostics is embedded with the BIOS and is launched by the BIOS
internally. The embedded system diagnostics provides a set of options for particular devices or device groups allowing you to:
●Run tests automatically or in an interactive mode
●Repeat tests
●Display or save test results
●Run thorough tests to introduce additional test options to provide extra information about the failed device(s)
●View status messages that inform you if tests are completed successfully
●View error messages that inform you of problems encountered during testing
NOTE: Some tests for specific devices require user interaction. Always ensure that you are present at the computer
terminal when the diagnostic tests are performed.
For more information, see Resolve Hardware Issues With Built-in and Online Diagnostics (SupportAssist ePSA, ePSA or PSA
Error Codes) .
Running the SupportAssist Pre-Boot System Performance Check
Steps
1. Turn on your computer.
2. As the computer boots, press the F12 key as the Dell logo appears.
3. On the boot menu screen, select the Diagnostics option.
4. Click the arrow at the bottom left corner.
Diagnostics front page is displayed.
5. Click the arrow in the lower-right corner to go to the page listing.
The items detected are listed.
6. To run a diagnostic test on a specific device, press Esc and click Yes to stop the diagnostic test.
7. Select the device from the left pane and click Run Tests.
8. If there are any issues, error codes are displayed.
Note the error code and validation number and contact Dell.
Diagnostic LED behavior
Table 21. Diagnostic LED behavior
Blinking pattern
Problem description Suggested resolutionAmber White
1 1 TPM detection failure Replace the system board.
1 2 Unrecoverable SPI Flash
Failure
Replace the system board.
1 5 EC unable to program i-Fuse Replace the system board.
Troubleshooting 75
Table 21. Diagnostic LED behavior (continued)
Blinking pattern
Problem description Suggested resolutionAmber White
1 6 Generic catch-all for
ungraceful EC code flow
errors
Disconnect all power source
(AC, battery, coin cell) and
drain flea power by pressing
and holding down power
button for 3~5 seconds.
2 1 CPU failure ●Run the Dell Support
Assist/Dell Diagnostics
tool.
●If problem persists,
replace the system board.
2 2 System board failure (included
BIOS corruption or ROM
error)
●Flash latest BIOS version
●If problem persists,
replace the system board.
2 3 No memory/RAM detected ●Confirm that the memory
module is installed
properly.
●If problem persists,
replace the memory
module.
2 4 Memory/RAM failure ●Reset and swap memory
modules among the slots.
●If problem persists,
replace the memory
module.
2 5 Invalid memory installed ●Reset and swap memory
modules among the slots.
●If problem persists,
replace the memory
module.
2 6 System board/Chipset Error Replace the system board.
2 7 LCD failure (SBIOS message) Replace the LCD module.
2 8 LCD failure (EC detection of
power rail failure)
Replace the system board.
3 1 CMOS battery failure ●Reset the main battery
connection.
●If problem persists,
replace the main battery.
3 2 PCI or Video card/chip failure Replace the system board.
3 3 BIOS Recovery image not
found
●Flash latest BIOS version
●If problem persists,
replace the system board.
3 4 BIOS Recovery image found
but invalid
●Flash latest BIOS version
●If problem persists,
replace the system board.
3 5 Power rail failure Replace the system board.
3 6 Flash corruption detected by
SBIOS.
●Press power button for
over 25 seconds to do
76 Troubleshooting
Table 21. Diagnostic LED behavior (continued)
Blinking pattern
Problem description Suggested resolutionAmber White
RTC reset. If problem
persists, replace the
system board.
●Disconnect all power
source (AC, battery, coin
cell) and drain flea power
by pressing and holding
down power button 3~5
seconds to ensure all
power are drained.
●Run "BIOS recovery from
USB", and the instructions
are in the website Dell
support.
●If problem persists,
replace the system board.
3 7 Timeout waiting on ME to
reply to HECI message.
Replace the system board.
NOTE: Blinking 3-3-3 LEDs on Lock LED (Caps-Lock or Nums-Lock), Power button LED (without Fingerprint reader), and
Diagnostic LED indicates failure to provide input during LCD panel test on Dell SupportAssist Pre-boot System Performance
Check diagnostics.
Diagnostic error messages
Table 22. Diagnostic error messages
Error messages Description
AUXILIARY DEVICE FAILURE The touchpad or external mouse may be faulty. For an
external mouse, check the cable connection. Enable the
Pointing Device option in the System Setup program.
BAD COMMAND OR FILE NAME Ensure that you have spelled the command correctly, put
spaces in the proper place, and used the correct path name.
CACHE DISABLED DUE TO FAILURE The primary cache internal to the microprocessor has failed.
Contact Dell
CD DRIVE CONTROLLER FAILURE The optical drive does not respond to commands from the
computer.
DATA ERROR The hard drive cannot read the data.
DECREASING AVAILABLE MEMORY One or more memory modules may be faulty or improperly
seated. Reinstall the memory modules or, if necessary, replace
them.
DISK C: FAILED INITIALIZATION The hard drive failed initialization. Run the hard drive tests in
Dell Diagnostics.
DRIVE NOT READY The operation requires a hard drive in the bay before it can
continue. Install a hard drive in the hard drive bay.
ERROR READING PCMCIA CARD The computer cannot identify the ExpressCard. Reinsert the
card or try another card.
EXTENDED MEMORY SIZE HAS CHANGED The amount of memory recorded in non-volatile memory
(NVRAM) does not match the memory module installed in the
Troubleshooting 77
Table 22. Diagnostic error messages (continued)
Error messages Description
computer. Restart the computer. If the error appears again,
Contact Dell
THE FILE BEING COPIED IS TOO LARGE FOR THE
DESTINATION DRIVE
The file that you are trying to copy is too large to fit on the
disk, or the disk is full. Try copying the file to a different disk
or use a larger capacity disk.
A FILENAME CANNOT CONTAIN ANY OF THE
FOLLOWING CHARACTERS: \ / : * ? " < > | -
Do not use these characters in filenames.
GATE A20 FAILURE A memory module may be loose. Reinstall the memory module
or, if necessary, replace it.
GENERAL FAILURE The operating system is unable to carry out the command.
The message is usually followed by specific information.
For example, Printer out of paper. Take the
appropriate action.
HARD-DISK DRIVE CONFIGURATION ERROR The computer cannot identify the drive type. Shut down the
computer, remove the hard drive, and boot the computer from
an optical drive. Then, shut down the computer, reinstall the
hard drive, and restart the computer. Run the Hard Disk
Drive tests in Dell Diagnostics.
HARD-DISK DRIVE CONTROLLER FAILURE 0 The hard drive does not respond to commands from the
computer. Shut down the computer, remove the hard drive,
and boot the computer from an optical drive. Then, shut
down the computer, reinstall the hard drive, and restart the
computer. If the problem persists, try another drive. Run the
Hard Disk Drive tests in Dell Diagnostics.
HARD-DISK DRIVE FAILURE The hard drive does not respond to commands from the
computer. Shut down the computer, remove the hard drive,
and boot the computer from an optical drive. Then, shut
down the computer, reinstall the hard drive, and restart the
computer. If the problem persists, try another drive. Run the
Hard Disk Drive tests in Dell Diagnostics.
HARD-DISK DRIVE READ FAILURE The hard drive may be defective. Shut down the computer,
remove the hard drive, and boot the computer from an
optical. Then, shut down the computer, reinstall the hard
drive, and restart the computer. If the problem persists,
try another drive. Run the Hard Disk Drive tests in Dell
Diagnostics.
INSERT BOOTABLE MEDIA The operating system is trying to boot to non-bootable media,
such as an optical drive. Insert bootable media.
INVALID CONFIGURATION INFORMATION-PLEASE RUN
SYSTEM SETUP PROGRAM
The system configuration information does not match the
hardware configuration. The message is most likely to occur
after a memory module is installed. Correct the appropriate
options in the system setup program.
KEYBOARD CLOCK LINE FAILURE For external keyboards, check the cable connection. Run the
Keyboard Controller test in Dell Diagnostics.
KEYBOARD CONTROLLER FAILURE For external keyboards, check the cable connection. Restart
the computer, and avoid touching the keyboard or the mouse
during the boot routine. Run the Keyboard Controller test in
Dell Diagnostics.
KEYBOARD DATA LINE FAILURE For external keyboards, check the cable connection. Run the
Keyboard Controller test in Dell Diagnostics.
KEYBOARD STUCK KEY FAILURE For external keyboards or keypads, check the cable
connection. Restart the computer, and avoid touching the
78 Troubleshooting
Table 22. Diagnostic error messages (continued)
Error messages Description
keyboard or keys during the boot routine. Run the Stuck Key
test in Dell Diagnostics.
LICENSED CONTENT IS NOT ACCESSIBLE IN
MEDIADIRECT
Dell MediaDirect cannot verify the Digital Rights Management
(DRM) restrictions on the file, so the file cannot be played.
MEMORY ADDRESS LINE FAILURE AT ADDRESS, READ
VALUE EXPECTING VALUE
A memory module may be faulty or improperly seated.
Reinstall the memory module or, if necessary, replace it.
MEMORY ALLOCATION ERROR The software you are attempting to run is conflicting with the
operating system, another program, or a utility. Shut down
the computer, wait for 30 seconds, and then restart it. Run
the program again. If the error message still appears, see the
software documentation.
MEMORY DOUBLE WORD LOGIC FAILURE AT ADDRESS,
READ VALUE EXPECTING VALUE
A memory module may be faulty or improperly seated.
Reinstall the memory module or, if necessary, replace it.
MEMORY ODD/EVEN LOGIC FAILURE AT ADDRESS,
READ VALUE EXPECTING VALUE
A memory module may be faulty or improperly seated.
Reinstall the memory module or, if necessary, replace it.
MEMORY WRITE/READ FAILURE AT ADDRESS, READ
VALUE EXPECTING VALUE
A memory module may be faulty or improperly seated.
Reinstall the memory module or, if necessary, replace it.
NO BOOT DEVICE AVAILABLE The computer cannot find the hard drive. If the hard drive is
your boot device, ensure that the drive is installed, properly
seated, and partitioned as a boot device.
NO BOOT SECTOR ON HARD DRIVE The operating system may be corrupted, Contact Dell.
NO TIMER TICK INTERRUPT A chip on the system board may be malfunctioning. Run the
System Set tests in Dell Diagnostics.
NOT ENOUGH MEMORY OR RESOURCES. EXIT SOME
PROGRAMS AND TRY AGAIN
You have too many programs open. Close all windows and
open the program that you want to use.
OPERATING SYSTEM NOT FOUND Reinstall the operating system. If the problem persists,
Contact Dell.
OPTIONAL ROM BAD CHECKSUM The optional ROM has failed. Contact Dell.
SECTOR NOT FOUND The operating system cannot locate a sector on the hard
drive. You may have a defective sector or corrupted File
Allocation Table (FAT) on the hard drive. Run the Windows
error-checking utility to check the file structure on the hard
drive. See Windows Help and Support for instructions (click
Start > Help and Support). If a large number of sectors are
defective, back up the data (if possible), and then format the
hard drive.
SEEK ERROR The operating system cannot find a specific track on the hard
drive.
SHUTDOWN FAILURE A chip on the system board may be malfunctioning. Run
the System Set tests in Dell Diagnostics. If the message
reappears, Contact Dell.
TIME-OF-DAY CLOCK LOST POWER System configuration settings are corrupted. Connect your
computer to an electrical outlet to charge the battery. If
the problem persists, try to restore the data by entering the
System Setup program, then immediately exit the program. If
the message reappears, Contact Dell.
TIME-OF-DAY CLOCK STOPPED The reserve battery that supports the system configuration
settings may require recharging. Connect your computer to an
electrical outlet to charge the battery. If the problem persists,
Contact Dell.
Troubleshooting 79
Table 22. Diagnostic error messages (continued)
Error messages Description
TIME-OF-DAY NOT SET-PLEASE RUN THE SYSTEM
SETUP PROGRAM
The time or date stored in the system setup program does
not match the system clock. Correct the settings for the Date
and Time options.
TIMER CHIP COUNTER 2 FAILED A chip on the system board may be malfunctioning. Run the
System Set tests in Dell Diagnostics.
UNEXPECTED INTERRUPT IN PROTECTED MODE The keyboard controller may be malfunctioning, or a memory
module may be loose. Run the System Memory tests and the
Keyboard Controller test in Dell Diagnostics or Contact
Dell.
X:\ IS NOT ACCESSIBLE. THE DEVICE IS NOT
READY
Insert a disk into the drive and try again.
System error messages
Table 23. System error messages
System message Description
Alert! Previous attempts at booting this
system have failed at checkpoint [nnnn]. For
help in resolving this problem, please note
this checkpoint and contact Dell Technical
Support
The computer failed to complete the boot routine three
consecutive times for the same error.
CMOS checksum error RTC is reset, BIOS Setup default has been loaded.
CPU fan failure CPU fan has failed.
System fan failure System fan has failed.
Hard-disk drive failure Possible hard disk drive failure during POST.
Keyboard failure Keyboard failure or loose cable. If reseating the cable does not
solve the problem, replace the keyboard.
No boot device available No bootable partition on hard disk drive, the hard disk drive
cable is loose, or no bootable device exists.
●If the hard drive is your boot device, ensure that the
cables are connected and that the drive is installed
properly and partitioned as a boot device.
●Enter system setup and ensure that the boot sequence
information is correct.
No timer tick interrupt A chip on the system board might be malfunctioning or
motherboard failure.
NOTICE - Hard Drive SELF MONITORING SYSTEM
has reported that a parameter has exceeded
its normal operating range. Dell recommends
that you back up your data regularly. A
parameter out of range may or may not
indicate a potential hard drive problem
S.M.A.R.T error, possible hard disk drive failure.
Recovering the operating system
When your computer is unable to boot to the operating system even after repeated attempts, it automatically starts Dell
SupportAssist OS Recovery.
80 Troubleshooting
Dell SupportAssist OS Recovery is a standalone tool that is preinstalled in all Dell computers installed with Windows 10 operating
system. It consists of tools to diagnose and troubleshoot issues that may occur before your computer boots to the operating
system. It enables you to diagnose hardware issues, repair your computer, back up your files, or restore your computer to its
factory state.
You can also download it from the Dell Support website to troubleshoot and fix your computer when it fails to boot into their
primary operating system due to software or hardware failures.
For more information about the Dell SupportAssist OS Recovery, see Dell SupportAssist OS Recovery User's Guide at
www.dell.com/support.
Real-Time Clock (RTC Reset)
The Real Time Clock (RTC) reset function allows you or the service technician to recover Dell Inspiron, systems from No
POST/No Power/No Boot situations. The legacy jumper enabled RTC reset has been retired on these models.
Start the RTC reset with the system powered off and connected to AC power. Press and hold the power button for thirty (30)
seconds. The system RTC Reset occurs after you release the power button.
Flashing the BIOS
About this task
You may need to flash (update) the BIOS when an update is available or when you replace the system board.
Follow these steps to flash the BIOS:
Steps
1. Turn on your computer.
2. Go to www.dell.com/support.
3. Click Product support, enter the Service Tag of your computer, and then click Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.
4. Click Drivers & downloads > Find it myself.
5. Select the operating system installed on your computer.
6. Scroll down the page and expand BIOS.
7. Click Download to download the latest version of the BIOS for your computer.
8. After the download is complete, navigate to the folder where you saved the BIOS update file.
9. Double-click the BIOS update file icon and follow the instructions on the screen.
Backup media and recovery options
It is recommended to create a recovery drive to troubleshoot and fix problems that may occur with Windows. Dell proposes
multiple options for recovering Windows operating system on your Dell PC. For more information. see Dell Windows Backup
Media and Recovery Options.
WiFi power cycle
About this task
If your computer is unable to access the internet due to WiFi connectivity issues a WiFi power cycle procedure may be
performed. The following procedure provides the instructions on how to conduct a WiFi power cycle:
NOTE: Some ISPs (Internet Service Providers) provide a modem/router combo device.
Troubleshooting 81
Steps
1. Turn off your computer.
2. Turn off the modem.
3. Turn off the wireless router.
4. Wait for 30 seconds.
5. Turn on the wireless router.
6. Turn on the modem.
7. Turn on your computer.
Flea power release
About this task
Flea power is the residual static electricity that remains on the computer even after it has been powered off and the battery has
been removed. The following procedure provides the instructions on how to conduct flea power release:
Steps
1. Turn off your computer.
2. Disconnect the power adapter from your computer.
3. Press and hold the power button for 15 seconds to drain the flea power.
4. Connect the power adapter to your computer.
5. Turn on your computer.
82 Troubleshooting
Getting help and contacting Dell
Self-help resources
You can get information and help on Dell products and services using these self-help resources:
Table 24. Self-help resources
Self-help resources Resource location
Information about Dell products and services www.dell.com
My Dell app
Tips
Contact Support In Windows search, type Contact Support, and press
Enter.
Online help for operating system www.dell.com/support/windows
Access top solutions, diagnostics, drivers and downloads, and
learn more about your computer through videos, manuals and
documents.
Your Dell computer is uniquely identified by a Service Tag or
Express Service Code. To view relevant support resources for
your Dell computer, enter the Service Tag or Express Service
Code at www.dell.com/support.
For more information on how to find the Service Tag for your
computer, see Locate the Service Tag on your computer.
Dell knowledge base articles for a variety of computer
concerns
1. Go to www.dell.com/support.
2. On the menu bar at the top of the Support page, select
Support > Knowledge Base.
3. In the Search field on the Knowledge Base page, type the
keyword, topic, or model number, and then click or tap the
search icon to view the related articles.
Contacting Dell
To contact Dell for sales, technical support, or customer service issues, see www.dell.com/contactdell.
NOTE: Availability varies by country/region and product, and some services may not be available in your country/region.
NOTE: If you do not have an active Internet connection, you can find contact information about your purchase invoice,
packing slip, bill, or Dell product catalog.
6
Getting help and contacting Dell 83