Table of Contents
- Latitude 3410 Service Manual
- Working on your computer
- Technology and components
- Major components of your system
- Disassembly and reassembly
- Troubleshooting
- Getting help
DELL 3410 User Manual
Displayed below is the user manual for 3410 by DELL which is a product in the Notebooks category. This manual has pages.
Related Manuals
Latitude 3410
Service Manual
1
Regulatory Model: P129G
Regulatory Type: P129G001/P129G002
September 2020
Rev. A01
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid
the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other
trademarks may be trademarks of their respective owners.
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid
the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Other trademarks may be trademarks of their respective owners.
Chapter 1: Working on your computer........................................................................................... 6
Safety instructions.............................................................................................................................................................. 6
Before working inside your computer.......................................................................................................................6
Safety precautions.........................................................................................................................................................7
Electrostatic discharge—ESD protection................................................................................................................7
ESD field service kit ..................................................................................................................................................... 8
After working inside your computer..........................................................................................................................9
Chapter 2: Technology and components.......................................................................................10
USB features.......................................................................................................................................................................10
USB Type-C.........................................................................................................................................................................12
HDMI 1.4............................................................................................................................................................................... 13
Power button LED behavior............................................................................................................................................ 14
Chapter 3: Major components of your system.............................................................................. 16
Chapter 4: Disassembly and reassembly.......................................................................................18
MicroSD card...................................................................................................................................................................... 18
Removing the microSD card......................................................................................................................................18
Installing the microSD card....................................................................................................................................... 20
Base cover.......................................................................................................................................................................... 20
Removing the base cover..........................................................................................................................................20
Installing the base cover............................................................................................................................................ 22
Battery................................................................................................................................................................................. 24
Lithium-ion battery precautions...............................................................................................................................24
Disconnecting the battery cable..............................................................................................................................24
Reconnecting the battery cable.............................................................................................................................. 25
Removing the battery.................................................................................................................................................26
Installing the battery................................................................................................................................................... 27
Memory modules............................................................................................................................................................... 28
Removing the memory module.................................................................................................................................28
Installing the memory modules.................................................................................................................................29
WLAN card..........................................................................................................................................................................30
Removing the WLAN card.........................................................................................................................................30
Installing the WLAN card............................................................................................................................................31
Coin-cell battery................................................................................................................................................................ 32
Removing the coin-cell battery................................................................................................................................32
Installing the coin-cell battery.................................................................................................................................. 33
DC-in port........................................................................................................................................................................... 34
Removing the DC-in....................................................................................................................................................34
Installing the DC-in......................................................................................................................................................35
Solid-state drive.................................................................................................................................................................37
Solid state drive bracket............................................................................................................................................ 37
Hard Drive............................................................................................................................................................................ 41
Contents
4 Contents
Removing the Hard Drive........................................................................................................................................... 41
Installing the Hard Drive............................................................................................................................................. 41
Touchpad.............................................................................................................................................................................42
Removing the touchpad.............................................................................................................................................42
Installing the touchpad............................................................................................................................................... 43
Speakers.............................................................................................................................................................................. 45
Removing the speakers..............................................................................................................................................45
Installing the speakers................................................................................................................................................ 46
Fan Assembly......................................................................................................................................................................47
Removing the Fan Assembly.....................................................................................................................................47
Installing the Fan Assembly.......................................................................................................................................48
Heatsink assembly.............................................................................................................................................................49
Removing the Heatsink Assembly - Discrete........................................................................................................49
Installing the Heatsink Assembly - Discrete..........................................................................................................49
Removing the Heatsink Assembly - UMA..............................................................................................................50
Installing the Heatsink Assembly - UMA.................................................................................................................51
System board..................................................................................................................................................................... 52
Removing the system board - Discrete................................................................................................................. 52
Installing the system board - Discrete................................................................................................................... 55
Removing the system board - UMA........................................................................................................................57
Installing the system board - UMA..........................................................................................................................60
IO Board...............................................................................................................................................................................63
Removing the IO Board..............................................................................................................................................63
Installing the IO Board................................................................................................................................................ 64
Power button..................................................................................................................................................................... 65
Removing the Power Button.................................................................................................................................... 65
Installing the Power Button...................................................................................................................................... 66
Display assembly................................................................................................................................................................67
Removing the Display Assembly...............................................................................................................................67
Installing the Display Assembly.................................................................................................................................70
Palmrest assembly.............................................................................................................................................................72
Removing the Palmrest Assembly........................................................................................................................... 72
Chapter 5: Troubleshooting......................................................................................................... 74
Enhanced Pre-Boot System Assessment (ePSA) diagnostics............................................................................... 74
Running SupportAssist diagnostics......................................................................................................................... 74
System diagnostic lights.................................................................................................................................................. 75
WiFi power cycle................................................................................................................................................................76
Chapter 6: Getting help............................................................................................................... 77
Contacting Dell...................................................................................................................................................................77
Contents 5
Working on your computer
Topics:
•Safety instructions
Safety instructions
Prerequisites
Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless
otherwise noted, each procedure included in this document assumes that the following conditions exist:
●You have read the safety information that shipped with your computer.
●A component can be replaced or, if purchased separately, installed by performing the removal procedure in reverse order.
About this task
NOTE: Disconnect all power sources before opening the computer cover or panels. After you finish working inside the
computer, replace all covers, panels, and screws before connecting to the power source.
WARNING: Before working inside your computer, read the safety information that shipped with your computer.
For additional safety best practices information, see the Regulatory Compliance Homepage
CAUTION: Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by
your warranty. Read and follow the safety instructions that came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically
touching an unpainted metal surface at the same time as touching a connector on the back of the computer.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a
card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by
its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some
cables have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking
tabs before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending
any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and
aligned.
NOTE: The color of your computer and certain components may appear differently than shown in this document.
Before working inside your computer
Steps
1. Save and close all open files and exit all open applications.
2. Shut down your computer. Click Start > Power > Shut down.
NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down
instructions.
1
6 Working on your computer
3. Disconnect your computer and all attached devices from their electrical outlets.
4. Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.
5. Remove any media card and optical disc from your computer, if applicable.
6. After the computer is unplugged, press and hold the power button for 5 seconds to ground the system board.
CAUTION: Place the computer on a flat, soft, and clean surface to avoid scratches on the display.
7. Place the computer face down.
Safety precautions
The safety precautions chapter details the primary steps to be taken before performing any disassembly instructions.
Observe the following safety precautions before you perform any installation or break/fix procedures involving disassembly or
reassembly:
●Turn off the system and all attached peripherals.
●Disconnect the system and all attached peripherals from AC power.
●Disconnect all network cables, telephone, and telecommunications lines from the system.
●Use an ESD field service kit when working inside any to avoid electrostatic discharge (ESD) damage.
●After removing any system component, carefully place the removed component on an anti-static mat.
●Wear shoes with non-conductive rubber soles to reduce the chance of getting electrocuted.
Standby power
Dell products with standby power must be unplugged before you open the case. Systems that incorporate standby power are
essentially powered while turned off. The internal power enables the system to be remotely turned on (wake on LAN) and
suspended into a sleep mode and has other advanced power management features.
Unplugging, pressing and holding the power button for 15 seconds should discharge residual power in the system board.
Bonding
Bonding is a method for connecting two or more grounding conductors to the same electrical potential. This is done through the
use of a field service electrostatic discharge (ESD) kit. When connecting a bonding wire, ensure that it is connected to bare
metal and never to a painted or non-metal surface. The wrist strap should be secure and in full contact with your skin, and
ensure that you remove all jewelry such as watches, bracelets, or rings prior to bonding yourself and the equipment.
Electrostatic discharge—ESD protection
ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards,
processors, memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such
as intermittent problems or a shortened product life span. As the industry pushes for lower power requirements and increased
density, ESD protection is an increasing concern.
Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than
in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.
Two recognized types of ESD damage are catastrophic and intermittent failures.
●Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes an
immediate and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has received
a static shock and immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or
nonfunctional memory.
●Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of
intermittent failures means that most of the time when damage occurs, it is not immediately recognizable. The DIMM
receives a static shock, but the tracing is merely weakened and does not immediately produce outward symptoms related to
the damage. The weakened trace may take weeks or months to melt, and in the meantime may cause degradation of memory
integrity, intermittent memory errors, etc.
Working on your computer 7
The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded")
failure.
Perform the following steps to prevent ESD damage:
●Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do
not provide adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on
parts with increased sensitivity to ESD damage.
●Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.
●When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static
packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you
discharge static electricity from your body.
●Before transporting a static-sensitive component, place it in an anti-static container or packaging.
ESD field service kit
The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components:
anti-static mat, wrist strap, and bonding wire.
Components of an ESD field service kit
The components of an ESD field service kit are:
●Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an
anti-static mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal
on the system being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly
on the mat. ESD-sensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.
●Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist
and bare metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that
is temporarily placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD
mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never use
wireless wrist straps. Always be aware that the internal wires of a wrist strap are prone to damage from normal wear and
tear, and must be checked regularly with a wrist strap tester in order to avoid accidental ESD hardware damage. It is
recommended to test the wrist strap and bonding wire at least once per week.
●ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored
kit, it is a best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A wrist
strap tester is the best method for doing this test. If you do not have your own wrist strap tester, check with your regional
office to find out if they have one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is
strapped to your wrist and push the button to test. A green LED is lit if the test is successful; a red LED is lit and an alarm
sounds if the test fails.
●Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts
that are insulators and often highly charged.
●Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For
example, deploying the kit for a server environment is different than for a desktop or portable environment. Servers are
typically installed in a rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always
look for a large open flat work area that is free of clutter and large enough to deploy the ESD kit with additional space to
accommodate the type of system that is being repaired. The workspace should also be free of insulators that can cause an
ESD event. On the work area, insulators such as Styrofoam and other plastics should always be moved at least 12 inches or
30 centimeters away from sensitive parts before physically handling any hardware components
●ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded
bags are preferred. However, you should always return the damaged part using the same ESD bag and packaging that the
new part arrived in. The ESD bag should be folded over and taped shut and all the same foam packing material should be
used in the original box that the new part arrived in. ESD-sensitive devices should be removed from packaging only at an
ESD-protected work surface, and parts should never be placed on top of the ESD bag because only the inside of the bag is
shielded. Always place parts in your hand, on the ESD mat, in the system, or inside an anti-static bag.
●Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts
to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.
8Working on your computer
ESD protection summary
It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static
mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all
insulator parts while performing service and that they use anti-static bags for transporting sensitive components.
After working inside your computer
About this task
NOTE: Leaving stray or loose screws inside your computer may severely damage your computer.
Steps
1. Replace all screws and ensure that no stray screws remain inside your computer.
2. Connect any external devices, peripherals, or cables you removed before working on your computer.
3. Replace any media cards, discs, or any other parts that you removed before working on your computer.
4. Connect your computer and all attached devices to their electrical outlets.
5. Turn on your computer.
Working on your computer 9
Technology and components
This chapter details the technology and components available in the system.
Topics:
•USB features
•USB Type-C
•HDMI 1.4
•Power button LED behavior
USB features
Universal Serial Bus, or USB, was introduced in 1996. It dramatically simplified the connection between host computers and
peripheral devices like mouses, keyboards, external drivers, and printers.
Table 1. USB evolution
Type Data Transfer Rate Category Introduction Year
USB 2.0 480 Mbps High Speed 2000
USB 3.2 Gen 1 5 Gbps Super-Speed 2010
USB 3.2 Gen 2 10 Gbps Super-Speed 2013
USB 3.2 Gen 1 (Super-Speed USB)
For years, the USB 2.0 has been firmly entrenched as the de facto interface standard in the PC world with about 6 billion
devices sold, and yet the need for more speed grows by ever faster computing hardware and ever greater bandwidth demands.
The USB 3.2 Gen 1 finally has the answer to the consumer's demands with a theoretically 10 times faster than its predecessor. In
a nutshell, USB 3.2 Gen 1 features are as follows:
●Higher transfer rates (up to 5 Gbps)
●Increased maximum bus power and increased device current draw to better accommodate power-hungry devices
●New power management features
●Full-duplex data transfers and support for new transfer types
●Backward USB 2.0 compatibility
●New connectors and cable
The topics below cover some of the most commonly asked questions regarding USB 3.2 Gen 1.
Speed
Currently, there are 3 speed modes that are defined by the latest USB 3.2 Gen 1 specification. They are Super-Speed, Hi-Speed,
and Full-Speed. The new Super-Speed mode has a transfer rate of 4.8 Gbps. While the specification retains Hi-Speed, and Full-
Speed USB mode, commonly known as USB 2.0 and 1.1 respectively, the slower modes still operate at 480 Mbps and 12 Mbps
respectively and are kept to maintain backward compatibility.
USB 3.2 Gen 1 achieves the much higher performance by the technical changes below:
●An additional physical bus that is added in parallel with the existing USB 2.0 bus (see the figure below).
2
10 Technology and components
●USB 2.0 previously had four wires (power, ground, and a pair for differential data); USB 3.2 Gen 1 adds four more for two
pairs of differential signals (receive and transmit) for a combined total of eight connections in the connectors and cabling.
●USB 3.2 Gen 1 utilizes the bi-directional data interface, rather than USB 2.0's half-duplex arrangement. This gives a 10-fold
increase in theoretical bandwidth.
With today's ever increasing demands that are placed on data transfers with high-definition video content, terabyte storage
devices, high megapixel count digital cameras etc., USB 2.0 may not be fast enough. Furthermore, no USB 2.0 connection could
ever come close to the 480Mbps theoretical maximum throughput, making data transfer at around 320 Mbps (40 MB/s) — the
actual real-world maximum. Similarly, USB 3.2 Gen 1 connections will never achieve 4.8Gbps. We will likely see a real-world
maximum rate of 400 MB/s with overheads. At this speed, USB 3.2 Gen 1 is a 10x improvement over USB 2.0.
Applications
USB 3.2 Gen 1 opens up the laneways and provides more headroom for devices to deliver a better overall experience. Where
USB video was barely tolerable previously (both from a maximum resolution, latency, and video compression perspective), it's
easy to imagine that with 5-10 times the bandwidth available, USB video solutions should work that much better. Single-link DVI
requires almost 2Gbps throughput. Where 480Mbps was limiting, 5Gbps is more than promising. With its promised 4.8Gbps
speed, the standard will find its way into some products that previously weren't USB territory, like external RAID storage
systems.
Listed below are some of the available Super-Speed USB 3.2 Gen 1 products:
●External Desktop USB 3.2 Gen 1 Hard Drives
●Portable USB 3.2 Gen 1 Hard Drives
●USB 3.2 Gen 1 Drive Docks & Adapters
●USB 3.2 Gen 1 Flash Drives & Readers
●USB 3.2 Gen 1 Solid-state Drives
●USB 3.2 Gen 1 RAIDs
●Optical Media Drives
●Multimedia Devices
●Networking
●USB 3.2 Gen 1 Adapter Cards & Hubs
Compatibility
The good news is that USB 3.2 Gen 1 has been carefully planned from the start to peacefully co-exist with USB 2.0. First of all,
while USB 3.2 Gen 1 specifies new physical connections and thus new cables to take advantage of the higher speed capability of
the new protocol, the connector itself remains the same rectangular shape with the four USB 2.0 contacts in the exact same
location as before. Five new connections to carry receive and transmitted data independently are present on USB 3.2 Gen 1
cables and only come into contact when connected to a proper Super-Speed USB connection.
Technology and components 11
USB Type-C
USB Type-C is a new, tiny physical connector. The connector itself can support various exciting new USB standards like USB 3.1
and USB power delivery (USB PD).
Alternate Mode
USB Type-C is a new connector standard that is very small. It is about a third the size of an old USB Type-A plug. This is a
single connector standard that every device should be able to use. USB Type-C ports can support a variety of different
protocols using “alternate modes,” which allows you to have adapters that can output HDMI, VGA, DisplayPort, or other types
of connections from that single USB port
USB Power Delivery
The USB PD specification is also closely intertwined with USB Type-C. Currently, smartphones, tablets, and other mobile
devices often use a USB connection to charge. A USB 2.0 connection provides up to 2.5 watts of power — that'll charge your
phone, but that's about it. A laptop might require up to 60 watts, for example. The USB Power Delivery specification ups this
power delivery to 100 watts. It's bi-directional, so a device can either send or receive power. And this power can be transferred
at the same time the device is transmitting data across the connection.
This could spell the end of all those proprietary laptop charging cables, with everything charging via a standard USB connection.
You could charge your laptop from one of those portable battery packs you charge your smartphones and other portable devices
from today. You could plug your laptop into an external display connected to a power cable, and that external display would
charge your laptop as you used it as an external display — all via the one little USB Type-C connection. To use this, the device
and the cable have to support USB Power Delivery. Just having a USB Type-C connection doesn't necessarily mean they do.
USB Type-C and USB 3.1
USB 3.1 is a new USB standard. USB 3's theoretical bandwidth is 5 Gbps, while USB 3.1's is 10 Gbps. That's double the
bandwidth, as fast as a first-generation Thunderbolt connector. USB Type-C isn't the same thing as USB 3.1. USB Type-C is just
a connector shape, and the underlying technology could just be USB 2 or USB 3.0. In fact, Nokia's N1 Android tablet uses a USB
Type-C connector, but underneath it's all USB 2.0 — not even USB 3.0. However, these technologies are closely related.
Thunderbolt over USB Type-C
Thunderbolt is a hardware interface that combines data, video, audio, and power in a single connection. Thunderbolt combines
PCI Express (PCIe) and DisplayPort (DP) into one serial signal, and additionally provides DC power, all in one cable. Thunderbolt
1 and Thunderbolt 2 use the same connector as miniDP (DisplayPort) to connect to peripherals, while Thunderbolt 3 uses a USB
Type-C connector.
Figure 1. Thunderbolt 1 and Thunderbolt 3
1. Thunderbolt 1 and Thunderbolt 2 (using a miniDP connector)
2. Thunderbolt 3 (using a USB Type-C connector)
12 Technology and components
Thunderbolt 3 over USB Type-C
Thunderbolt 3 brings Thunderbolt to USB Type-C at speeds up to 40 Gbps, creating one compact port that does it all -
delivering the fastest, most versatile connection to any dock, display or data device like an external hard drive. Thunderbolt 3
uses a USB Type-C connector/port to connect to supported peripherals.
1. Thunderbolt 3 uses USB Type-C connector and cables - It is compact and reversible
2. Thunderbolt 3 supports speed up to 40 Gbps
3. DisplayPort 1.4 – compatible with existing DisplayPort monitors, devices and cables
4. USB Power Delivery - Up to 130W on supported computers
Key Features of Thunderbolt 3 over USB Type-C
1. Thunderbolt, USB, DisplayPort and power on USB Type-C on a single cable (features vary between different products)
2. USB Type-C connector and cables which are compact and reversible
3. Supports Thunderbolt Networking (*varies between different products)
4. Supports up to 4K displays
5. Up to 40 Gbps
NOTE: Data transfer speed may vary between different devices.
Thunderbolt Icons
Figure 2. Thunderbolt Iconography Variations
HDMI 1.4
This topic explains the HDMI 1.4 and its features along with the advantages.
HDMI (High-Definition Multimedia Interface) is an industry-supported, uncompressed, all-digital audio/video interface. HDMI
provides an interface between any compatible digital audio/video source, such as a DVD player, or A/V receiver and a
compatible digital audio and/or video monitor, such as a digital TV (DTV). The primary advantage is cable reduction and content
protection provisions. HDMI supports standard, enhanced, or high-definition video, plus multichannel digital audio on a single
cable.
HDMI 1.4 Features
●HDMI Ethernet Channel - Adds high-speed networking to an HDMI link, allowing users to take full advantage of their IP-
enabled devices without a separate Ethernet cable.
●Audio Return Channel - Allows an HDMI-connected TV with a built-in tuner to send audio data "upstream" to a surround
audio system, eliminating the need for a separate audio cable.
●3D - Defines input/output protocols for major 3D video formats, paving the way for true 3D gaming and 3D home theater
applications.
●Content Type - Real-time signaling of content types between display and source devices, enabling a TV to optimize picture
settings based on content type.
●Additional Color Spaces - Adds support for additional color models used in digital photography and computer graphics.
●4K Support - Enables video resolutions far beyond 1080p, supporting next-generation displays that will rival the Digital
Cinema systems used in many commercial movie theaters.
Technology and components 13
●HDMI Micro Connector - A new, smaller connector for phones and other portable devices, supporting video resolutions up
to 1080p.
●Automotive Connection System - New cables and connectors for automotive video systems, designed to meet the unique
demands of the motoring environment while delivering true HD quality.
Advantages of HDMI
●Quality HDMI transfers uncompressed digital audio and video for the highest, crispest image quality.
●Low-cost HDMI provides the quality and functionality of a digital interface while also supporting uncompressed video
formats in a simple, cost-effective manner.
●Audio HDMI supports multiple audio formats from standard stereo to multichannel surround sound.
●HDMI combines video and multichannel audio into a single cable, eliminating the cost, complexity, and confusion of multiple
cables currently used in A/V systems.
●HDMI supports communication between the video source (such as a DVD player) and the DTV, enabling new functionality.
Power button LED behavior
On certain Dell Latitude systems, the power button LED is used to provide an indication of the system status, and as a result the
power button illuminates when pressed. The systems with the optional power button/fingerprint reader will have no LED under
the power button and hence will apply the available LED's in the system to provide an indication of the system status.
Power button LED behavior without Fingerprint reader
●System is ON (S0) = LED illuminates solid white.
●System in Sleep/Standby (S3, SOix) = LED is off
●System is Off/Hibernating (S4/S5) = LED is off
Power On and LED behavior with Fingerprint reader
●Pressing the power button for a duration between 50 msec to 2 sec turns on the device.
●Power button does not register additional presses until the SOL (Sign-Of-Life) has been provided to the user.
●System LED's illuminates upon pressing the power button.
●All the available LED's (Keyboard backlit/ Keyboard caps lock LED/ Battery Charge LED) illuminates and displays specified
behavior.
●The auditory tone is Off by default. It can be enabled in the BIOS setup.
●Safeguards do not time out if the device gets hung during the logon process.
●Dell logo: Turns on within 2 secs after pressing the power button.
●Full boot: Within 22 secs after pressing the power button.
●Below is the example timelines:
14 Technology and components
Power button with fingerprint reader will have no LED and will leverage the available LED's in the system to provide indication of
the system status
●Power Adapter LED:
○The LED on Power adapter connector illuminates white when power is supplied from electrical outlet.
●Battery Indicator LED:
○If the computer is connected to an electrical outlet, the battery light operates as follows:
1. Solid white -the battery is charging. When the charge is complete the LED turns off.
○If the computer is running on a battery, the battery light operates as follows:
1. Off -the battery is adequately charged (or the computer is turned off).
2. Solid amber -the battery charge is critically low. A low battery state is approximately 30 minutes or less of battery life
remaining.
●Camera LED
○White LED activates when camera is on.
●Mic Mute LED:
○When activated (muted), the mic mute LED on the F4 Key should illuminate WHITE.
●RJ45 LEDs:
○Table 2. LED on either side of RJ45 port
Link speed indicator (LHS) Activity indicator (RHS)
Green Amber
Technology and components 15
Major components of your system
1. Base cover
2. Battery
3. DC-in Port
4. Heatsink
5. Memory Modules
6. Speakers
7. System Board
8. Touchpad
9. Palmrest Assembly
10. Display Assembly
11. Power Button Module
12. Coin-cell Battery
13. IO Board
14. Fan Assembly
15. WLAN Card
16. Solid-state Drive
17. Hard Drive Assembly
3
16 Major components of your system
NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These
parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative for
purchase options.
Major components of your system 17
Disassembly and reassembly
Topics:
•MicroSD card
•Base cover
•Battery
•Memory modules
•WLAN card
•Coin-cell battery
•DC-in port
•Solid-state drive
•Hard Drive
•Touchpad
•Speakers
•Fan Assembly
•Heatsink assembly
•System board
•IO Board
•Power button
•Display assembly
•Palmrest assembly
MicroSD card
Removing the microSD card
Prerequisites
1. Follow the procedure in Before working inside your computer.
4
18 Disassembly and reassembly
About this task
Steps
1. Push the microSD card to release it from the computer.
2. Slide the microSD card out of the computer.
Disassembly and reassembly 19
Installing the microSD card
About this task
Steps
1. Align the microSD card to its slot on the computer.
2. Slide the microSD card into the slot until it clicks into place.
Next steps
Follow the procedures in After working inside your computer.
Base cover
Removing the base cover
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the SD Card.
20 Disassembly and reassembly
About this task
Disassembly and reassembly 21
Steps
1. Loosen the six (M2.5x6) and two (M2.5x7) screws that secure the base cover to the computer.
2. Using a plastic scribe, pry the base cover from the top-right corner and lift the base cover away from the computer.
Installing the base cover
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
22 Disassembly and reassembly
About this task
The figure indicates the location of the base cover and provides a visual representation of the installation procedure.
Disassembly and reassembly 23
Steps
1. Align and place the base cover on the computer, press the edges and sides of the base cover until it snaps into place.
2. Tighten the six (M2.5x6) and two (M2.5x7) screws to secure the base cover to the computer.
Next steps
1. Replace the SD Card.
2. Follow the procedure in after working inside your computer.
Battery
Lithium-ion battery precautions
CAUTION:
●Exercise caution when handling Lithium-ion batteries.
●Discharge the battery completely before removing it. Disconnect the AC power adapter from the system and
operate the computer solely on battery power—the battery is fully discharged when the computer no longer
turns on when the power button is pressed.
●Do not crush, drop, mutilate, or penetrate the battery with foreign objects.
●Do not expose the battery to high temperatures, or disassemble battery packs and cells.
●Do not apply pressure to the surface of the battery.
●Do not bend the battery.
●Do not use tools of any kind to pry on or against the battery.
●Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental
puncture or damage to the battery and other system components.
●If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing,
bending, or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical
support for assistance. See www.dell.com/contactdell.
●Always purchase genuine batteries from www.dell.com or authorized Dell partners and resellers.
Disconnecting the battery cable
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD card.
3. Remove the base cover.
24 Disassembly and reassembly
Steps
Use the pull tab to disconnect the battery cable from the connector on the system board.
Reconnecting the battery cable
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the battery cable and provides a visual representation of the installation procedure.
Disassembly and reassembly 25
Steps
Re-connect the battery cable to the connector on the system board.
Next steps
1. Replace the base cover.
2. Replace the SD Card.
3. Follow the procedure in after working inside your computer
Removing the battery
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the microSD card.
3. Remove the base cover.
26 Disassembly and reassembly
Steps
1. Disconnect the battery cable from the connector on the system board.
2. Remove the five (M2x3) screws that secures the battery to the palm rest assembly.
3. Lift and move the battery away from the computer.
Installing the battery
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the battery and provides a visual representation of the installation procedure.
Disassembly and reassembly 27
Steps
1. Align the tabs on the battery with the slots on the palm rest assembly.
2. Place the battery in the battery bay.
3. Tighten the five (M2x3) screws to secure the battery to the palm rest assembly.
4. Connect the battery cable to the connector on the system board.
Next steps
1. Replace the base cover.
2. Replace the SD Card.
3. Follow the procedure in after working inside your computer
Memory modules
Removing the memory module
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the SD Card.
3. Remove the base cover.
4. Disconnect the battery.
About this task
The following images indicate the location of the memory module and provide a visual representation of the removal procedure.
28 Disassembly and reassembly
Steps
1. Pry the clips securing the memory module until the memory module pops-up.
2. Remove the memory module from the memory slot.
Installing the memory modules
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the memory module and provides a visual representation of the installation procedure.
Disassembly and reassembly 29
Steps
1. Align the notch on the memory module with the tab on the memory module slot.
2. Slide the memory module firmly into the slot at an angle.
3. Press the memory module down until it clicks into place.
NOTE: If you do not hear the click, remove the memory module and reinstall it.
Next steps
1. Install the battery.
2. Install the base cover.
3. Install the SD Card.
4. Follow the procedure in After working inside your computer.
WLAN card
Removing the WLAN card
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the SD card
3. Remove the base cover.
4. Disconnect the battery cable.
About this task
The figure indicates the location of the WLAN card and provides a visual representation of the removal procedure.
30 Disassembly and reassembly
Steps
1. Remove the single (M2x3) screw that secures the WLAN bracket to the computer.
2. Remove the WLAN bracket.
3. Disconnect the WLAN antenna cables from the WLAN module.
4. Slide and remove the WLAN card from the WLAN card slot.
Installing the WLAN card
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the WLAN card and provides a visual representation of the installation procedure.
Disassembly and reassembly 31
Steps
1. Align the notch on the WLAN card with the tab on the WLAN-card slot and insert the WLAN card at an angle into the
WLAN-card slot.
2. Connect the WLAN antenna cables to the WLAN card.
3. Align and place the WLAN-card bracket to secure the WLAN card to the system board.
4. Replace the single (M2x3) screw to secure the WLAN card to the system board.
Next steps
1. Reconnect the battery cable.
2. Install the base cover.
3. Install the SD Card
4. Follow the procedure in After working inside your computer.
Coin-cell battery
Removing the coin-cell battery
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the SD card.
32 Disassembly and reassembly
3. Remove the base cover.
4. Disconnect the battery cable.
About this task
The figure indicates the location of the coin-cell battery and provides a visual representation of the removal procedure.
Steps
1. Disconnect the coin-cell battery cable from the system board.
2. Peel the coin-cell battery off the palmrest assembly as the coin-cell is affixed to the board with an adhesive.
NOTE: CAUTION: The removal of the coin cell battery will result in an RTC error and will clear all CMOS settings.
Installing the coin-cell battery
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the coin-cell and provides a visual representation of the installation procedure.
Disassembly and reassembly 33
Steps
1. Re-adhere the coin-cell battery to the slot on the palmrest assembly.
2. Connect the coin-cell battery cable to the system board.
Next steps
1. Reconnect the battery cable.
2. Install the base cover.
3. Install the SD card
4. Follow the procedure in After working inside your computer.
DC-in port
Removing the DC-in
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the SD card.
3. Remove the base cover.
4. Disconnect the battery cable.
About this task
The figure indicates the location of the DC-in and provides a visual representation of the removal procedure.
34 Disassembly and reassembly
Steps
1. Locate the DC-in port on your computer, remove the three (M2.5x5) screws from the hinge covering it.
2. Lift the hinge and fold it away from the chassis.
3. Disconnect the DC-in cable from the computer and remove the single (M2x3) screw.
4. Remove the DC-in port from the computer.
Installing the DC-in
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the DC-in port and provides a visual representation of the installation procedure.
Disassembly and reassembly 35
Steps
1. Place the DC-in module into the provided slot.
2. Install the (M2x3) screw and connect the DC-in cable to the system board.
3. Fold and align the hinge to the screw holders on the palmrest.
4. Install the three (M2.5x5) screws to secure the hinge.
Next steps
1. Reconnect the battery cable.
2. Install the base cover.
3. Install the SD card.
4. Follow the procedure in After working inside your computer.
36 Disassembly and reassembly
Solid-state drive
Solid state drive bracket
Removing the M.2 2280 solid-state drive
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the SD Card.
3. Remove the base cover.
4. Disconnect the battery.
About this task
The figure indicates the location of the M.2 2280 solid-state drive and provides a visual representation of the removal
procedure.
Steps
1. Remove the single (M2x3) screw that secures the solid-state module to the palmrest assembly.
2. Slide the solid-state module out from the M.2 slot.
Installing M.2 2280 solid-state drive
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the M.2 2280 solid-state drive and provides a visual representation of the installation
procedure.
Disassembly and reassembly 37
Steps
1. Align and slide the solid-state drive into the slot.
2. Replace the single (M2x3) screw to secure the solid-state drive module to the system.
Next steps
1. Install the battery cable.
2. Install the base cover.
3. Install the SD card.
4. Follow the procedure in After working inside your computer.
Removing the M.2 2230 solid-state drive
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the SD Card.
3. Remove the base cover.
4. Disconnect the battery.
About this task
The figure indicates the location of the M.2 2230 solid-state drive and provides a visual representation of the removal
procedure.
38 Disassembly and reassembly
Steps
1. Remove the single (M2x3) screw that secures the solid-state module to the palmrest assembly.
2. Slide the solid-state module out from the M.2 slot.
Installing M.2 2230 solid-state drive
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the M.2 2230 solid-state drive and provides a visual representation of the installation
procedure.
Disassembly and reassembly 39
Steps
1. Align and slide the solid-state drive into the slot.
2. Replace the single (M2x3) screw to secure the solid-state drive module to the palmrest and keyboard assembly.
Next steps
1. Install the battery cable.
2. Install the base cover.
3. Install the SD card.
4. Follow the procedure in After working inside your computer.
Installing M.2 solid-state drive bracket
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the M.2 solid-state drive bracket and provides a visual representation of the installation
procedure.
Steps
1. Slide the bracket out of the metal holder.
2. Rotate the bracket so that it faces the opposite side from its original mounting position.
3. Slide the bracket into the metal holder on the opposite end.
Next steps
1. Install the battery cable.
2. Install the base cover.
40 Disassembly and reassembly
3. Follow the procedure in After working inside your computer.
Hard Drive
Removing the Hard Drive
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the SD Card.
3. Remove the base cover.
4. Disconnect the battery.
About this task
The following images indicate the location of the hard drive and provide a visual representation of the removal procedure.
Steps
1. Remove the four M3x3 screws and disconnect the hard drive cable from the connector on the system board.
2. Remove the hard drive from the computer.
Installing the Hard Drive
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the Hard Drive and provides a visual representation of the installation procedure.
Disassembly and reassembly 41
Steps
1. Align the screw holes on the hard drive assembly with the mounting points on the palmrest.
2. Replace the four M3x3 screws to secure the hard drive in place and connect the hard drive cable to the connector on the
system board.
Next steps
1. Install the battery.
2. Install the base cover.
3. Install the SD card.
4. Follow the procedure in After working inside your computer.
Touchpad
Removing the touchpad
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the SD Card.
3. Remove the base cover.
4. Remove the battery.
42 Disassembly and reassembly
About this task
Steps
1. Remove the three (M2x2) screws from the bottom portion of the touchpad.
2. Disconnect the ribbon cable from the system board.
3. Peel away the adhesive straps holding the top portion of the touchpad.
4. Remove the four (M2x2) screws from the top portion of the touchpad and lift the touchpad away from the computer.
Installing the touchpad
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the touchpad and provides a visual representation of the installation procedure.
Disassembly and reassembly 43
Steps
1. Place the touchpad onto the palmrest, ensure the screw posts align with the ones on the palmrest. Install the four (M2x2)
screws to the top of touchpad.
2. Fold back the two adhesive tape strips onto the touchpad.
3. Connect the ribbon cable from the touchpad to the system board.
4. Install the three (M2x2) screws into the screw posts at the bottom of the palmrest
Next steps
1. Install the battery.
2. Install the base cover.
3. Install the SD card.
4. Follow the procedure in After working inside your computer.
44 Disassembly and reassembly
Speakers
Removing the speakers
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the SD Card.
3. Remove the base cover.
4. Remove the battery.
About this task
The figure indicates the location of the speakers and provides a visual representation of the removal procedure.
Steps
1. Disconnect the speaker cable from the connector on the system board and peel back the adhesive strips holing the
connected cables in place.
2. Ensure the cables are free and lift the speaker modules from both ends of the computer.
Disassembly and reassembly 45
Installing the speakers
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the speakers and provides a visual representation of the installation procedure.
Steps
1. Place the speaker assembly onto the mounting points on the bottom base on the computer.
2. Route the cables from both the speaker modules through the middle section of the bottom base, above the touchpad, and
fold back the adhesive strips to secure the cables. Once secured, connect the speaker's cable connector to the connector
on the system board.
Next steps
1. Install the battery.
2. Install the base cover.
3. Install the SD card.
4. Follow the procedure in After working inside your computer.
46 Disassembly and reassembly
Fan Assembly
Removing the Fan Assembly
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the SD Card.
3. Remove the base cover.
4. Disconnect the battery.
About this task
The figure indicates the location of the fan assembly and provides a visual representation of the removal procedure.
Steps
1. Disconnect the IO board cable from the connector on the system board and remove the cables from the cable management
routes along side the fan assembly.
2. Disconnect the fan cable from the system board.
Disassembly and reassembly 47
3. Disconnect the WLAN antenna cables, and remove the cables from the cable management routes along side the fan
assembly.
4. Remove the two (M2x2) screws from the fan assembly and lift the fan assembly away from the computer.
Installing the Fan Assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the fan assembly and provides a visual representation of the installation procedure.
Steps
1. Place the fan assembly onto the mounting points on the palmrest on the computer and install the two (M2x2) screws.
2. Route the antenna cables along the cable management routes on the fan assembly and connect the cables to the WLAN
card.
3. Install the two (M2x2) screws onto the fan assembly and secure it in place.
4. Route the IO board cable along the cable management route on the fan assembly and connect it to the system board.
48 Disassembly and reassembly
Next steps
1. Install the battery.
2. Install the base cover.
3. Install the SD card.
4. Follow the procedure in After working inside your computer.
Heatsink assembly
Removing the Heatsink Assembly - Discrete
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the SD Card.
3. Remove the base cover.
4. Disconnect the battery.
About this task
The following images indicate the location of the heatsink and provide a visual representation of the removal procedure.
Steps
1. Loosen the seven captive screws that secure the heatsink to the system board.
2. Lift the heatsink assembly away from the computer.
Installing the Heatsink Assembly - Discrete
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
Disassembly and reassembly 49
About this task
The figure indicates the location of the heatsink and provides a visual representation of the installation procedure.
Steps
1. Place the heatsink onto the system board ensuring the mounting points on heatsink and system board align.
2. Tighten the seven captive screws to secure the heatsink to the system board.
Next steps
1. Install the battery.
2. Install the base cover.
3. Install the SD Card.
4. Follow the procedure in After working inside your computer.
Removing the Heatsink Assembly - UMA
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the SD Card.
3. Remove the base cover.
4. Disconnect the battery.
About this task
The following images indicate the location of the heatsink and provide a visual representation of the removal procedure.
50 Disassembly and reassembly
Steps
1. Loosen the four captive screws that secure the heatsink to the system board.
2. Lift the heatsink assembly away from the computer.
Installing the Heatsink Assembly - UMA
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the heatsink and provides a visual representation of the installation procedure.
Disassembly and reassembly 51
Steps
1. Place the heatsink onto the system board ensuring the mounting points on heatsink and system board align.
2. Tighten the four captive screws to secure the heatsink to the system board.
Next steps
1. Install the battery.
2. Install the base cover.
3. Install the SD Card.
4. Follow the procedure in After working inside your computer.
System board
Removing the system board - Discrete
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the SD Card.
3. Remove the base cover.
4. Disconnect the battery.
5. Remove the memory modules.
6. Remove the WLAN card.
7. Remove the solid state drive.
8. Remove the heatsink.
About this task
The figure indicates the location of the system board and provides a visual representation of the removal procedure.
52 Disassembly and reassembly
Disassembly and reassembly 53
Steps
1. Remove the three (M2.5x5) screws from the right hinge.
2. Disconnect the DC-in connector cable from the system board.
3. Disconnect the Fan assembly cable from the system board.
4. Lift the latch that locks down the LCD cable onto the system board.
5. Disconnect the LCD cable from the system board.
6. Peel back the adhesive tape from over the IO board connector cable and disconnect the IO boards connector cable.
7. Disconnect the connector cables from the system board in the following order (left - right): Speaker, Touchpad, USB,
Battery, Keyboard.
54 Disassembly and reassembly
8. Remove the two (M2.3x5) screws from the system board and the two (M2) screws holding the metal shield. Then lift the
system board away from the chassis.
Installing the system board - Discrete
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the system board and provides a visual representation of the installation procedure.
Disassembly and reassembly 55
56 Disassembly and reassembly
Steps
1. Place the system board onto the palmrest, aligning the screw posts from the palmrest. Place the metal shield onto the USB
port module and install the two (M2) screws. Install the two (M2.3x5) screws to secure the system board to the palmrest.
2. Connect the DC-in port connector back to the system board.
3. Fold the right hinge back, install the three (M2.5x5) to secure the hinge in place.
4. Connect the fan connector back to the system board.
5. Connect the LCD cable back to the system board.
6. Fold the LCD connectors latch to secure it in place.
7. Connect the IO board cable to the system board.
8. Connect the following cables in the following order (left - right): Speaker, Touchpad, USB, Battery, Keyboard.
Next steps
1. Install the Heatsink.
2. Install the WLAN card.
3. Install the Solid state drive.
4. Install the memory module.
5. Install the battery.
6. Install the base cover.
7. Install the SD Card.
8. Follow the procedure in After working inside your computer.
Removing the system board - UMA
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the SD Card.
3. Remove the base cover.
4. Disconnect the battery.
5. Remove the memory modules.
6. Remove the WLAN card.
7. Remove the solid state drive.
8. Remove the heatsink.
About this task
The figure indicates the location of the system board and provides a visual representation of the removal procedure.
Disassembly and reassembly 57
58 Disassembly and reassembly
Steps
1. Disconnect the IO board connector cable from the system board.
2. Disconnect the Fan connector cable from the system board.
3. Remove the three (M2.5x5) screws from the right hinge and fold it up.
4. Peel back the adhesive tape from the LCD cable and disconnect the LCD cable from the system board.
5. Peel back the adhesive tape from the DC-in cable connector and disconnect the DC-in cable from the system board.
6. Remove the two (M2x4) screws from the metal shield covering the USB module.
7. Lift and take the metal shield away from the system.
8. Disconnect the connector cables from the system board in the following order (left - right): Speaker, Touchpad, USB,
Battery, Keyboard.
9. Remove the two (M2x4) screws from the system board and lift the board away from the computer.
Disassembly and reassembly 59
NOTE: For systems configured with a WWAN card, an additional cable must be disconnected from under the system
board, while flipping the board over.
Installing the system board - UMA
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the system board and provides a visual representation of the installation procedure.
60 Disassembly and reassembly
Disassembly and reassembly 61
Steps
1. Place the system board onto the palmrest, aligning the screw posts to the mounting points on the palmrest. Install the two
(M2x4) screws to secure the system board to the palmrest.
62 Disassembly and reassembly
NOTE: For systems configured with a WWAN card, you must connect the cable from WWAN daughterboard to the
connector on the systemboard.
2. Connect the IO board cable to the system board.
3. Connect the fan connector back to the system board.
4. Fold the right hinge back, install the three (M2.5x5) to secure the hinge in place.
5. Connect the LCD cable back to the system board and fold the adhesive tape back onto the LCD connector.
6. Connect the DC-in port connector back to the system board and fold the adhesive tape back onto the DC-in connector.
7. Place the metal shield onto the USB port module.
8. Install the two (M2x4) screws to secure the metal shield.
9. Connect the following cables in the following order (left - right): Speaker, Touchpad, USB, Battery, Keyboard.
Next steps
1. Install the Heatsink.
2. Install the WLAN card.
3. Install the Solid state drive.
4. Install the memory module.
5. Install the battery.
6. Install the base cover.
7. Install the SD Card.
8. Follow the procedure in After working inside your computer.
IO Board
Removing the IO Board
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the SD Card.
3. Remove the base cover.
Disassembly and reassembly 63
4. Disconnect the battery.
5. Remove the WLAN card.
NOTE: Hall Sensor is a part of the IO board and the entire IO board needs to be replaced if the Hall Sensor is faulty.
About this task
The following images indicate the location of the memory module and provide a visual representation of the removal procedure.
Steps
1. Remove the two (M2.5x5) screws from the left hinge and lift the hinge up.
2. Peel back the adhesive tape covering the IO board connector cable and disconnect it from the system board.
3. Disconnect the cable connectors from the IO board in the following order (left - right): USB data cable, Coin-cell battery
cable, Audio FFC cable.
4. Remove the single (M2x5) screw that is holding the IO board in place and lift the module away from the computer.
Installing the IO Board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the IO board and provides a visual representation of the installation procedure.
64 Disassembly and reassembly
Steps
1. Place the IO board onto the mounting points on the palmrest and secure it using the single (M2x5) screw.
2. Connect the three cable connectors to the connectors on lower right side of the IO board.
3. Route the IO Board connector cable through the routing points under the fan assembly and connect the cable to the
connector on the system board. Fold the adhesive tape back onto the IO Board connector on the system board.
4. Using the two (M2x3) screws, close and secure the left hinge to the palmrest.
Next steps
1. Install the WLAN card.
2. Install the battery.
3. Install the base cover.
4. Install the SD Card.
5. Follow the procedure in After working inside your computer.
Power button
Removing the Power Button
Prerequisites
1. Follow the procedure in before working inside your computer.
Disassembly and reassembly 65
2. Remove the SD Card.
3. Remove the base cover.
4. Disconnect the battery.
5. Remove the IO board.
6. Remove the solid state drive.
About this task
The figure indicates the location of the Power Button and provides a visual representation of the removal procedure.
Steps
1. Disconnect the power button connector cable from the daughterboard module. Peel off the adhesive cover from over the
power button assembly.
2. Remove the two (M2x2) screws that secure the shield over the power button module.
3. Lift the Power Button module away from the computer.
Installing the Power Button
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the power button and provides a visual representation of the installation procedure.
66 Disassembly and reassembly
Steps
1. Place the Power Button module onto the mounting points on the palmrest.
2. Place the shield on top of the power button module and install the two (M2x2) screws to secure the shield onto the power
button.
3. Connect the cable connector to the daughterboard module.
Next steps
1. Install the Solid state drive.
2. Install the IO board.
3. Install the battery.
4. Install the base cover.
5. Install the SD Card.
6. Follow the procedure in After working inside your computer.
Display assembly
Removing the Display Assembly
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the SD Card.
3. Remove the base cover.
4. Disconnect the battery.
About this task
The figure indicates the location of the LCD Assembly and provides a visual representation of the removal procedure.
Disassembly and reassembly 67
68 Disassembly and reassembly
Steps
1. Remove the five M2.5x5 screws from both the hinges. Lift and fold the hinges backwards.
2. Peel back the adhesive tape covering the LCD cable.
3. Fold the adhesive tape away from the LCD cable.
4. Remove the LCD cable and lift it away from the computer.
5. Move the system away from the LCD assembly.
Disassembly and reassembly 69
Installing the Display Assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the LCD Assembly and provides a visual representation of the installation procedure.
70 Disassembly and reassembly
Steps
1. Place the display assembly on a clean and flat surface.
2. Align and place the palmrest and keyboard assembly on the display assembly.
3. Using the alignment posts, close the display hinges.
4. Connect the display cable to the system board and adhere the tape to secure the display cable.
5. Place the EDP metal bracket on the display cable connector.
6. Install the six (M2.5x5) screws that secure the display hinges to the chassis of your computer.
Next steps
1. Install the battery.
2. Install the base cover.
3. Install the SD card.
4. Follow the procedure in After working inside your computer.
Disassembly and reassembly 71
Palmrest assembly
Removing the Palmrest Assembly
Prerequisites
1. Follow the procedure in before working inside your computer.
2. Remove the SD card.
3. Remove the base cover.
4. Remove the battery.
5. Remove the WLAN card.
6. Remove the coin-cell battery.
7. Remove the memory modules.
8. Remove the DC-in.
9. Remove the solid state drive.
10. Remove the hard drive.
11. Remove the touchpad.
12. Remove the speakers.
13. Remove the heatsink.
14. Remove the system board.
NOTE: The system board can be removed along with the heat sink.
About this task
The figure indicates the location of the Palmrest Assembly and provides a visual representation of the removal procedure.
Steps
Once the required parts are removed, the bare palmrest assembly can be accessed and removed.
Next steps
1. Install the system board
2. Install the heatsink.
72 Disassembly and reassembly
3. Install the speakers.
4. Install the touchpad.
5. Install the hard drive.
6. Install the solid state drive.
7. Install the DC-in.
8. Install the memory modules.
9. Install the coin-cell battery.
10. Install the WLAN card.
11. Install the battery.
12. Install the base cover.
13. Install the SD card SD card.
1. Follow the procedure in after working inside your computer.
Disassembly and reassembly 73
Troubleshooting
Topics:
•Enhanced Pre-Boot System Assessment (ePSA) diagnostics
•System diagnostic lights
•WiFi power cycle
Enhanced Pre-Boot System Assessment (ePSA)
diagnostics
About this task
The SupportAssist diagnostics (also known as system diagnostics) performs a complete check of your hardware. The
SupportAssist diagnostics is embedded with the BIOS and is launched by the BIOS internally. The embedded system diagnostics
provides a set of options for particular devices or device groups allowing you to:
●Run tests automatically or in an interactive mode
●Repeat tests
●Display or save test results
●Run thorough tests to introduce additional test options to provide extra information about the failed device(s)
●View status messages that inform you if tests are completed successfully
●View error messages that inform you of problems encountered during testing
NOTE: The SupportAssist window displays, listing all devices detected in the computer. The diagnostics starts running the
tests on all the detected devices.
Running SupportAssist diagnostics
Steps
1. Turn on your computer.
2. As the computer boots, press the F12 key as the Dell logo appears.
3. On the boot menu screen, select the Diagnostics option.
4. Click the arrow at the bottom left corner.
Diagnostics front page is displayed.
5. Click the arrow in the lower-right corner to go to the page listing.
The items detected are listed.
6. To run a diagnostic test on a specific device, press Esc and click Yes to stop the diagnostic test.
7. Select the device from the left pane and click Run Tests.
8. If there are any issues, error codes are displayed.
Note the error code and validation number and contact Dell.
SupportAssist diagnostic User Interface
SupportAssist diagnostic User Interface
About this task
This section contains information on Support Assist Basic and Advanced Screen.
5
74 Troubleshooting
SupportAssist opens the basic screen on start. You can switch to the advanced screen using the icon at the bottom left of the
screen. The advanced screen shows detected devices in a tiled format. Specific tests can be included or excluded only in the
advanced mode. The Basic Screen has minimal controls which allows easy navigation for the user to start or stop the
diagnostics.
System diagnostic lights
Battery-status light
Indicates the power and battery-charge status.
Solid white — Power adapter is connected and the battery has more than 5 percent charge.
Amber — Computer is running on battery and the battery has less than 5 percent charge.
Off
●Power adapter is connected and the battery is fully charged.
●Computer is running on battery and the battery has more than 5 percent charge.
●Computer is in sleep state, hibernation, or turned off.
The power and battery-status light blinks amber along with beep codes indicating failures.
For example, the power and battery-status light blinks amber two times followed by a pause, and then blinks white three times
followed by a pause. This 2,3 pattern continues until the computer is turned off indicating no memory or RAM is detected.
The following table shows different power and battery-status light patterns and associated problems.
Table 3. LED codes
Diagnostic light codes Problem description
2,1 Processor failure
2,2 System board: BIOS or ROM (Read-Only Memory) failure
2,3 No memory or RAM (Random-Access Memory) detected
2,4 Memory or RAM (Random-Access Memory) failure
2,5 Invalid memory installed
2,6 System-board or chipset error
2,7 Display failure
2,8 LCD power rail failure. Replace system board and LCD
3,1 Coin-cell battery failure
3,2 PCI, video card/chip failure
3,3 Recovery image not found
3,4 Recovery image found but invalid
3,5 Power-rail failure
3,6 System BIOS Flash incomplete
3,7 Management Engine (ME) error
Camera status light: Indicates whether the camera is in use.
●Solid white — Camera is in use.
●Off — Camera is not in use.
Caps Lock status light: Indicates whether Caps Lock is enabled or disabled.
●Solid white — Caps Lock enabled.
●Off — Caps Lock disabled.
Troubleshooting 75
WiFi power cycle
About this task
If your computer is unable to access the internet due to WiFi connectivity issues a WiFi power cycle procedure may be
performed. The following procedure provides the instructions on how to conduct a WiFi power cycle:
NOTE: Some ISPs (Internet Service Providers) provide a modem/router combo device.
Steps
1. Turn off your computer.
2. Turn off the modem.
3. Turn off the wireless router.
4. Wait for 30 seconds.
5. Turn on the wireless router.
6. Turn on the modem.
7. Turn on your computer.
76 Troubleshooting
Getting help
Topics:
•Contacting Dell
Contacting Dell
Prerequisites
NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing
slip, bill, or Dell product catalog.
About this task
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and
some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues:
Steps
1. Go to Dell.com/support.
2. Select your support category.
3. Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.
4. Select the appropriate service or support link based on your need.
6
Getting help 77