Table of Contents
- Dell Vostro 14–3468 Owner's Manual
- Working on your computer
- Disassembly and reassembly
- Recommended tools
- Screw size list
- Chassis view
- Battery
- Optical drive
- Keyboard lattice and Keyboard
- Base cover
- Hard drive
- Fingerprint reader
- WLAN card
- Memory modules
- Coin-cell battery
- Power button board
- Heat sink
- System fan
- Speaker
- System board
- Input-Output board
- Power connector port
- Display assembly
- Display bezel
- Camera
- Display panel
- Display hinges
- Palm rest
- Technology and components
- System setup
- Enhanced Pre-Boot System Assessment — ePSA diagnostics
- Technical specifications
- Contacting Dell
DELL 3468 User Manual
Displayed below is the user manual for 3468 by DELL which is a product in the Notebooks category. This manual has pages.
Related Manuals
Dell Vostro 14–3468
Owner's Manual
Regulatory Model: P76G
Regulatory Type: P76G002
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2018 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks
may be trademarks of their respective owners.
2018 - 01
Rev. A01
Contents
1 Working on your computer............................................................................................................................. 7
Safety instructions............................................................................................................................................................. 7
Before working inside your computer.............................................................................................................................. 7
Turning o your computer................................................................................................................................................ 8
Turning o your — Windows......................................................................................................................................8
Turning o your computer — Windows 7.................................................................................................................8
After working inside your computer.................................................................................................................................8
2 Disassembly and reassembly..........................................................................................................................9
Recommended tools.......................................................................................................................................................... 9
Screw size list..................................................................................................................................................................... 9
Chassis view......................................................................................................................................................................10
Front open view..........................................................................................................................................................10
Left view.......................................................................................................................................................................11
Palm rest view.............................................................................................................................................................12
Right view....................................................................................................................................................................13
Battery............................................................................................................................................................................... 13
Removing the battery................................................................................................................................................ 13
Installing the battery...................................................................................................................................................14
Optical drive...................................................................................................................................................................... 14
Removing the optical drive .......................................................................................................................................14
Removing the optical drive bracket..........................................................................................................................15
Installing the optical drive bracket............................................................................................................................ 16
Installing the optical drive.......................................................................................................................................... 16
Keyboard lattice and Keyboard....................................................................................................................................... 16
Removing the keyboard............................................................................................................................................. 16
Installing the keyboard................................................................................................................................................18
Base cover.........................................................................................................................................................................18
Removing the base cover..........................................................................................................................................18
Installing the base cover............................................................................................................................................ 21
Hard drive.......................................................................................................................................................................... 21
Removing the hard drive assembly...........................................................................................................................21
Removing the hard drive from the hard drive bracket.......................................................................................... 22
Installing the hard drive into the hard drive bracket.............................................................................................. 23
Installing the hard drive assembly............................................................................................................................ 23
Fingerprint reader.............................................................................................................................................................23
Removing the ngerprint reader..............................................................................................................................23
Installing the ngerprint reader................................................................................................................................ 24
WLAN card....................................................................................................................................................................... 25
Removing the WLAN card........................................................................................................................................ 25
Installing the WLAN card.......................................................................................................................................... 25
Memory modules............................................................................................................................................................. 26
Removing the memory module................................................................................................................................ 26
Contents 3
Installing the memory module...................................................................................................................................27
Coin-cell battery............................................................................................................................................................... 27
Removing the coin cell battery.................................................................................................................................27
Installing the coin cell battery................................................................................................................................... 28
Power button board.........................................................................................................................................................28
Removing the power button board..........................................................................................................................28
Installing the power button board............................................................................................................................ 29
Heat sink .......................................................................................................................................................................... 30
Removing the heat sink ........................................................................................................................................... 30
Installing the heat sink ..............................................................................................................................................30
System fan.........................................................................................................................................................................31
Removing the system fan.......................................................................................................................................... 31
Installing the system fan............................................................................................................................................32
Speaker............................................................................................................................................................................. 32
Removing the speakers.............................................................................................................................................32
Installing the speakers............................................................................................................................................... 33
System board....................................................................................................................................................................33
Removing the system board.....................................................................................................................................33
Installing the system board....................................................................................................................................... 36
Input-Output board.......................................................................................................................................................... 37
Removing the Input-Output board ..........................................................................................................................37
Installing the Input-Output board ............................................................................................................................37
Power connector port..................................................................................................................................................... 38
Removing the power connector.............................................................................................................................. 38
Installing the power connector.................................................................................................................................39
Display assembly.............................................................................................................................................................. 39
Removing the display assembly............................................................................................................................... 39
Installing the display assembly...................................................................................................................................41
Display bezel..................................................................................................................................................................... 42
Removing the display bezel.......................................................................................................................................42
Installing the display bezel.........................................................................................................................................42
Camera.............................................................................................................................................................................. 43
Removing the camera............................................................................................................................................... 43
Installing the camera..................................................................................................................................................43
Display panel..................................................................................................................................................................... 44
Removing the display panel...................................................................................................................................... 44
Installing the display panel.........................................................................................................................................45
Display hinges...................................................................................................................................................................45
Removing the display hinges.................................................................................................................................... 45
Installing the display hinges.......................................................................................................................................46
Palm rest........................................................................................................................................................................... 47
Replacing the palmrest..............................................................................................................................................47
Installing the palmrest................................................................................................................................................48
3 Technology and components........................................................................................................................49
Processors........................................................................................................................................................................ 49
Identifying processors in Windows 10..................................................................................................................... 49
4Contents
Identifying processors in Windows 8.......................................................................................................................49
Identifying processors in Windows 7.......................................................................................................................50
Verifying the processor usage in Task Manager..................................................................................................... 51
Verifying the processor usage in Resource Monitor...............................................................................................51
Chipsets............................................................................................................................................................................ 52
Downloading the chipset driver............................................................................................................................... 52
Identifying the chipset in Device Manager on Windows 10..................................................................................52
Identifying chipset in Device Manager on Windows 8.......................................................................................... 52
Identifying chipset in Device Manager on Windows 7...........................................................................................53
Intel chipset drivers....................................................................................................................................................54
Graphics card................................................................................................................................................................... 54
Intel HD Graphics drivers.......................................................................................................................................... 54
Intel HD Graphics 520............................................................................................................................................... 55
Display options................................................................................................................................................................. 56
Identifying the display adapter................................................................................................................................. 56
Rotating the display...................................................................................................................................................56
Downloading drivers.................................................................................................................................................. 57
Changing the screen resolution................................................................................................................................57
Adjusting brightness in Windows 10........................................................................................................................ 58
Adjusting brightness in Windows 8..........................................................................................................................58
Adjusting brightness in Windows 7..........................................................................................................................58
Cleaning the display...................................................................................................................................................58
Connecting to external display devices...................................................................................................................59
Hard drive options............................................................................................................................................................59
Identifying the hard drive in Windows 10................................................................................................................59
Identifying the hard drive in Windows 8..................................................................................................................59
Identifying the hard drive in Windows 7..................................................................................................................60
Entering BIOS setup..................................................................................................................................................60
USB features.................................................................................................................................................................... 60
USB 3.0/USB 3.1 Gen 1 (SuperSpeed USB)...........................................................................................................60
Speed........................................................................................................................................................................... 61
Applications.................................................................................................................................................................62
Compatibility...............................................................................................................................................................62
HDMI 1.4............................................................................................................................................................................62
HDMI 1.4 Features......................................................................................................................................................63
Advantages of HDMI................................................................................................................................................. 63
USB Powershare..............................................................................................................................................................63
Camera features...............................................................................................................................................................64
Identifying the camera in Device Manager on Windows 10..................................................................................64
Identifying the camera in Device Manager on Windows 8................................................................................... 64
Identifying the camera in Device Manager on Windows 7....................................................................................64
Starting the camera...................................................................................................................................................64
Starting the camera app........................................................................................................................................... 65
Memory features..............................................................................................................................................................66
Verifying system memory ........................................................................................................................................ 66
Verifying system memory in setup...........................................................................................................................66
Testing memory using ePSA.....................................................................................................................................66
Contents 5
Audio drivers.....................................................................................................................................................................66
4 System setup............................................................................................................................................... 67
Boot Sequence.................................................................................................................................................................67
Navigation keys................................................................................................................................................................ 67
System setup options......................................................................................................................................................68
Updating the BIOS in Windows .....................................................................................................................................75
System and setup password...........................................................................................................................................76
Assigning a system setup password........................................................................................................................ 76
Deleting or changing an existing system setup password.................................................................................... 76
5 Enhanced Pre-Boot System Assessment — ePSA diagnostics.................................................................... 78
Running the ePSA Diagnostics.......................................................................................................................................78
6 Technical specications............................................................................................................................... 79
7 Contacting Dell............................................................................................................................................ 84
6 Contents
Working on your computer
Safety instructions
Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise
noted, each procedure included in this document assumes that the following conditions exist:
• You have read the safety information that shipped with your computer.
• A component can be replaced or, if purchased separately, installed by performing the removal procedure in the reverse order.
WARNING: Disconnect all power sources before opening the computer cover or panels. After you nish working inside the
computer, replace all covers, panels, and screws before connecting to the power source.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional
safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance
CAUTION: Many repairs may only be done by a certied service technician. You should only perform troubleshooting and simple
repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an
unpainted metal surface that is grounded to ground yourself before you touch the computer to perform any disassembly tasks.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its
edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have
connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the
cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a
cable, ensure that both connectors are correctly oriented and aligned.
NOTE: The color of your computer and certain components may appear dierently than shown in this document.
Before working inside your computer
To avoid damaging your computer, perform the following steps before you begin working inside the computer.
1 Ensure that you follow the Safety instructions.
2 Ensure that your work surface is at and clean to prevent the computer cover from being scratched.
3 Turn o your computer (see Turning o your computer).
4 If the computer is connected to a docking device (docked), undock it.
CAUTION: To disconnect a network cable, rst unplug the cable from your computer and then unplug the cable from the
network device.
5 Disconnect all network cables from the computer.
6 Disconnect your computer and all attached devices from their electrical outlets.
7 Close the display and turn the computer upside-down on a at work surface.
NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer.
8 Remove the main battery.
9 Turn the computer top-side up.
1
Working on your computer 7
10 Open the display.
11 Press the power button to ground the system board.
CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the
display.
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as
the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static
electricity, which could harm internal components.
12 Remove any installed ExpressCards or Smart Cards from the appropriate slots.
Turning o your computer
Turning o your — Windows
CAUTION: To avoid losing data, save and close all open les and exit all open programs before you turn o your computer .
1 Click or tap .
2 Click or tap and then click or tap Shut down.
NOTE: Ensure that the computer and all attached devices are turned o. If your computer and attached devices did not
automatically turn o when you shut down your operating system, press and hold the power button for about 6 seconds to
turn them o.
Turning o your computer — Windows 7
CAUTION: To avoid losing data, save and close all open les and exit all open programs before you turn o your computer.
1 Click Start.
2 Click Shut Down.
NOTE: Ensure that the computer and all attached devices are turned o. If your computer and attached devices did not
automatically turn o when you shut down your operating system, press and hold the power button for about 6 seconds to
turn them o.
After working inside your computer
After you complete any replacement procedure, ensure that you connect external devices, cards, and cables before turning on your
computer.
CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries
designed for other Dell computers.
1 Connect any external devices, such as a port replicator or media base, and replace any cards, such as an ExpressCard.
2 Connect any telephone or network cables to your computer.
CAUTION: To connect a network cable, rst plug the cable into the network device and then plug it into the
computer.
3 Connect your computer and all attached devices to their electrical outlets.
4 Turn on your computer.
8Working on your computer
Disassembly and reassembly
Recommended tools
The procedures in this document require the following tools:
• Phillips #0 screwdriver
• Phillips #1 screwdriver
• Small plastic scribe
Screw size list
Table 1. Vostro 14–3468 screw size list
Component M2L2(Big
head 07)
M2L2(Big
head 05) M2L2.5 M2L5
M2L3
(Thin
head)
M2.5L2.5
(Big head) M2.5L8 M3L3
Optical drive 2
Optical drive bracket 1
Base Cover 6 1 1 8
Hard drive 2
Hard drive bracket 4
System fan 2
System board 1
Power connector 1
Display assembly 3
Camera
Display panel 4
Hinge 6
Power button board 1 1
Fingerprint reader 1
2
Disassembly and reassembly 9
Chassis view
Front open view
1 Camera 2 Camera-status light
3 Microphone 4 LCD panel
5 Power and battery-status light/ Hard-drive activity light
10 Disassembly and reassembly
Left view
1 Power connector 2 Network connector
3 VGA connector 4 HDMI 1.4 connector
5 USB 3.1 Gen 1 connector 6 USB 3.1 Gen 1 connector
Disassembly and reassembly 11
Palm rest view
1 Power button 2 Keyboard
3 Fingerprint reader 4 Palm rest
5 Touchpad
12 Disassembly and reassembly
Right view
1 SD card reader 2 Universal audio port
3 USB 2.0 connector 4 Optical drive
5 Security cable slot
Battery
Removing the battery
1 Follow the procedure in Before working inside your computer.
2 To remove the battery:
a Slide the release latch to release the battery [1].
b Remove the battery from the computer [2].
Disassembly and reassembly 13
Installing the battery
1 Insert the battery into the slot and press until it clicks into place.
2 Follow the procedures in After working inside your computer.
Optical drive
Removing the optical drive
1 Follow the procedure in Before working inside your computer.
2 Remove the battery.
3 To remove the optical drive:
a Remove the two M2L3 screws that secure the optical drive to the computer [1].
b Using a plastic scribe, push the tab in the direction of the arrow indicated on the chassis. [2].
c Slide the optical drive out of the computer [3].
14 Disassembly and reassembly
Removing the optical drive bracket
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
3 To remove the optical drive from the bracket:
a Remove the single M2L2(Big head05) screw that secures the optical drive bracket.
b Remove the optical drive bracket from the optical drive .
Disassembly and reassembly 15
Installing the optical drive bracket
1 Install the optical drive bracket.
2 Tighten the single M2L2(Big head05) screw to secure the optical drive bracket.
3 Install the:
aoptical drive
bbattery
4 Follow the procedure in After working inside your computer.
Installing the optical drive
1 Insert the optical drive into the slot until it clicks into place.
2 Tighten the two M2L3 screws to secure the optical drive to the computer.
3 Install the battery.
4 Follow the procedure in After working inside your computer.
Keyboard lattice and Keyboard
Removing the keyboard
1 Follow the procedure in Before working inside your computer.
2 Remove the battery.
3 To remove the keyboard:
a Using a plastic scribe, release the ve tabs from the slots located above the keyboard [1].
b Flip the keyboard on the palm rest to access the keyboard connector cable under the keyboard [2].
16 Disassembly and reassembly
4 To remove the keyboard cable:
a Disconnect the keyboard cable from the system board.
b Remove the keyboard from the computer.
Disassembly and reassembly 17
Installing the keyboard
1 Connect the keyboard cable to the connector on the system board.
2 Slide the keyboard to align it with the tabs.
3 Press along the top edges to lock the keyboard in place.
4 Install the battery.
5 Follow the procedure in After working inside your computer.
Base cover
Removing the base cover
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
ckeyboard
3 To remove the base cover:
a Disconnect the optical drive connector and lift it to remove it from the system board [1].
18 Disassembly and reassembly
b Remove the three M2L5 screws that secure the base cover [2].
4 Flip the computer and remove the screws (3 screws - M2L2; 2 screws- M2L2; 8 screws - M2.5L8) that secure the base cover to the
computer [1, 2, 3].
Disassembly and reassembly 19
5 To remove the base cover:
a Use a scribe to pry the edges of the base cover [1].
b Lift the base cover and remove it from the computer [2].
20 Disassembly and reassembly
Installing the base cover
1 Align the base cover with the screw holders on the computer.
2 Press the edges of the cover until it clicks into place.
3 Tighten the ( 8 screws - M2.5L8; 3 screws - M2L2; 2 screws- M2L2) screws to secure the base cover to the computer.
4 Flip the computer over.
5 Open the display and connect the optical drive connector to the system board.
6 Tighten the three M2L5 screws to secure the base cover to the palm rest.
7 Install the:
akeyboard
boptical drive
cbattery
8 Follow the procedure in After working inside your computer.
Hard drive
Removing the hard drive assembly
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
Disassembly and reassembly 21
boptical drive
ckeyboard
dbase cover
3 To remove the hard drive assembly:
a Disconnect the hard drive cable from the connector on the system board [1].
b Remove the two M2L3 screws that secure the hard drive assembly to the computer [2].
c Lift the hard drive assembly away from the computer [3].
Removing the hard drive from the hard drive bracket
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
ckeyboard
dbase cover
ehard drive assembly
3 To remove the hard drive from the hard drive assembly:
a Pull the hard drive cable connector to remove it from the hard drive [1].
b Remove the four M3L3 screws that secure the hard drive bracket to the hard drive [2].
c Lift the hard drive from the hard drive bracket [3].
22 Disassembly and reassembly
Installing the hard drive into the hard drive bracket
1 Align the screw holders and insert the hard drive into the hard drive bracket.
2 Tighten the four M3L3 screws to secure the hard drive to the hard drive bracket.
3 Connect the hard drive cable connector to the hard drive.
4 Install the:
ahard drive assembly
bbase cover
ckeyboard
doptical drive
ebattery
5 Follow the procedure in After working inside your computer
Installing the hard drive assembly
1 Insert the hard drive assembly into the slot on the computer.
2 Tighten the two M2L3 screws to secure the hard drive assembly to the computer.
3 Connect the hard drive cable to the connector on the system board.
4 Install the:
abase cover
bkeyboard
coptical drive
dbattery
5 Follow the procedures in After working inside your computer.
Fingerprint reader
Removing the ngerprint reader
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
Disassembly and reassembly 23
ckeyboard
dbase cover
ehard drive
fI/O board
3 To remove the ngerprint reader:
a Disconnect the ngerprint reader from the connector on the system board [1].
b Remove the single M2L2.5 screw that secures the hard drive assembly to the computer [2, 3].
c Lift the ngerprint reader board away from the computer [4].
Installing the ngerprint reader
1 Place the ngerprint reader board into the slot on the computer.
2 Tighten the single M2L2.5 screw that secures the ngerprint reader to the computer.
3 Connect the ngerprint reader cable to the connector on the system board.
4 Install the:
aI/O board
bhard drive
cbase cover
dkeyboard
eoptical drive
fbattery
5 Follow the procedures in After working inside your computer.
24 Disassembly and reassembly
WLAN card
Removing the WLAN card
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
ckeyboard
dbase cover
3 To remove the WLAN card:
a Remove the single M2L3 screw that secures the tab to the WLAN card [1].
b Lift the tab that secures the WLAN card [2].
c Disconnect the WLAN cables from the connectors on the WLAN card [3].
d Slide the WLAN card from the connector on the system board [4].
Installing the WLAN card
1 Install the WLAN card to the connector on the system board.
2 Connect the WLAN cables to the connectors on the WLAN card.
Disassembly and reassembly 25
3 Place the securing tab on the WLAN card and tighten the M2L3 screw on the computer.
4 Install the:
abase cover
bkeyboard
coptical drive
dbattery
5 Follow the procedure in After working inside your computer.
Memory modules
Removing the memory module
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
ckeyboard
dbase cover
3 To remove memory module:
a Pull the clips securing the memory module until the memory module pops up [1].
b Remove the memory module from the system board [2].
26 Disassembly and reassembly
Installing the memory module
1 Insert the memory module into the memory socket.
2 Press the memory module until the clips secure the memory module.
3 Install the:
abase cover
bkeyboard
coptical drive
dbattery
4 Follow the procedures in After working inside your computer.
Coin-cell battery
Removing the coin cell battery
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
ckeyboard
dbase cover
3 Use a plastic scribe to lift the battery out of the slot [1,2].
Disassembly and reassembly 27
Installing the coin cell battery
1 Insert the coin cell battery into the battery slot.
2 Press the battery until it clicks into place.
3 Install the:
abattery
bkeyboard
coptical drive
dbattery
4 Follow the procedures in After working inside your computer.
Power button board
Removing the power button board
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
ckeyboard
28 Disassembly and reassembly
dbase cover
3 To remove the power button board:
a Disconnect the system board cable from the computer [1].
b Remove the single display hinge screw (M2.5L8) from the computer [2].
c Flip the display hinge to reveal the power button board beneath the hinge [3].
d Remove the single screw [M2L2(Big head07)] that secures the power button board to the chassis [4].
e Peel the system board cable from the chassis and then peel the tape that holds the power button board.
f Slide the Power button board away from the chassis.
Installing the power button board
1 Place the button board on the chassis.
2 Ax the tape that holds the power button board.
3 Ax the system board cable to the chassis.
4 Place the power button board and tighten the single [M2L2(Big head07)] screw.
5 Connect the system board cable to the power button board.
6 Tighten the single (M2.5L8) screw to secure the display hinge to the power button board.
7 Install the:
abase cover
bkeyboard
coptical drive
dbattery
8 Follow the procedures in After working inside your computer.
Disassembly and reassembly 29
Heat sink
Removing the heat sink
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
ckeyboard
dbase cover
3 To remove the heat sink:
a Loosen the four captive screws that secure the heat sink to the system board [1, 2, 3, 4].
NOTE: Loosen the screws in the order of the callout numbers [1, 2, 3, 4]. These screws are retention screws and
cannot be fully removed.
b Remove the heat sink from the system board [5 ].
Installing the heat sink
1 Align the screws on the heat sink with the screw holders on the system board.
2 Tighten the four captive screws to secure it to the system board.
NOTE: Secure the screws in the order of the callout numbers [1, 2, 3, 4].
3 Install the:
abase cover
30 Disassembly and reassembly
bkeyboard
coptical drive
dbattery
4 Follow the procedures in After working inside your computer.
System fan
Removing the system fan
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
ckeyboard
dbase cover
3 To remove the system fan:
a Disconnect the system fan connector cable from the system board [1].
b Remove the two M2L5 screws that secure the system fan to the computer [2].
c Lift and remove the system fan from the chassis [3].
Disassembly and reassembly 31
Installing the system fan
1 Align the system fan on the chassis.
2 Secure the system fan to the computer by tightening the two M2L5 screws.
3 Connect the system fan connector cable to the system board connector.
4 Install the:
abase cover
bkeyboard
coptical drive
dbattery
5 Follow the procedures in After working inside your computer.
Speaker
Removing the speakers
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
ckeyboard
dbase cover
3 To remove the speakers:
a Disconnect the speaker cable from the computer [1].
b Remove the speakers from the computer [2].
32 Disassembly and reassembly
Installing the speakers
1 Place the speakers into the slots on the computer.
2 Connect the speaker cable to the system board.
3 Install the:
abase cover
bkeyboard
coptical drive
dbattery
4 Follow the procedure in After working inside your computer
System board
Removing the system board
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
ckeyboard
dbase cover
eWLAN card
fmemory module
gheat sink
hsystem fan
3 Lift the locking tab to disconnect the following cables
angerprint reader connector [1]
b power button board connector [2]
c remove the adhesive tape [3]
d lift the locking tab and disconnect the eDP connector [4]
e touchpad connector [5]
f speaker [6]
g I/O connector [7]
h hard drive connector [8]
Disassembly and reassembly 33
4 Remove the single M2L3 screws that secure the system board to the computer [1] and lift the system board [2].
34 Disassembly and reassembly
5 Flip the system board.
6 To remove the system board:
a Peel the adhesive tape [1].
b Unlock the tab and disconnect the power cable [2].
c Remove the system board from the computer.
Disassembly and reassembly 35
Installing the system board
1 Connect the power cable cable.
2 Ax the adhesive tape.
3 Flip the system board.
4 Align the system board with the screw holders on the computer.
5 Tighten the single M2L3 screw to secure the system board to the computer.
6 Connect the following cables to the system board.
a hard drive connector
b touchpad connector
c speaker connector
d I/O connector
e eDP connector
f power connector
gngerprint connector
7 Install the:
asystem fan
bheat sink
cmemory module
dWLAN Card
ebase cover
fkeyboard
goptical drive
hbattery
8 Follow the procedure in After working inside your computer.
36 Disassembly and reassembly
Input-Output board
Removing the Input-Output board
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
ckeyboard
dbase cover
ehard drive assembly
3 To remove the Input/Output board (I/O board):
a Disconnect the I/O board cable [1].
b Lift and remove the I/O board from the computer [2].
Installing the Input-Output board
1 Place the I/O board on the computer.
2 Connect the input/output (I/O board) cable to the I/O board.
3 Install the:
Disassembly and reassembly 37
ahard drive assembly
bbase cover
ckeyboard
doptical drive
ebattery
4 Follow the procedure in After working inside your computer.
Power connector port
Removing the power connector
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
ckeyboard
dbase cover
ehard drive assembly
fWLAN card
gmemory module
hheat sink
isystem fan
jsystem board
3 To remove the power connector:
a Remove the single [M2x2 (Big head 07)] screw that secures the power connector to the computer [1].
b Lift the power connector [2].
38 Disassembly and reassembly
Installing the power connector
1 Insert the power connector into the slot on the computer.
2 Secure the power connector to the computer by using the single [ M2x2 (Big head 07)] screw.
3 Install the:
asystem board
bsystem fan
cWLAN Card
dmemory module
eheat sink
fhard drive assembly
gbase cover
hkeyboard
ioptical drive
jbattery
4 Follow the procedure in After working inside your computer.
Display assembly
Removing the display assembly
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
ckeyboard
dbase cover
eWLAN card
3 To remove the display assembly:
a Unroute the WLAN cable [1].
b Peel the adhesive tape [2].
c Lift the locking tab [3].
d Disconnect the eDP cable [4].
Disassembly and reassembly 39
4 Flip the computer.
5 To remove the display assembly:
40 Disassembly and reassembly
NOTE: Place the chassis on the edge of a table with the display facing down.
a Remove the three M2.5L8 screws that secure the display hinge to the computer [1].
CAUTION: Practice caution when handling the LCD HUD by supporting it with one hand, while working on the hinges.
b Lift and remove the display assembly [2].
Installing the display assembly
1 Align the display assembly with the chassis.
2 Connect the eDP cable to the connector on the system board and lock the locking tab.
3 Ax the adhesive tape to secure the eDP cable.
4 Route the WLAN and display assembly cables through the cable-securing tabs.
5 Tighten the display hinges three M2.5L8 screws to secure the display assembly.
6 Install the:
aWLAN Card
bbase cover
ckeyboard
doptical drive
ebattery
7 Follow the procedure in After working inside your computer.
Disassembly and reassembly 41
Display bezel
Removing the display bezel
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
ckeyboard
dbase cover
eWLAN card
fdisplay assembly
3 To disconnect the display bezel:
a Use a plastic scribe to release the tabs on the edges to release the display bezel from the display assembly.
b Remove the display bezel display assembly.
Installing the display bezel
1 Place the display bezel on the display assembly.
2 Press the display bezel on the edges until it snaps onto the display assembly.
3 Install the:
adisplay assembly
bWLAN Card
cbase cover
dkeyboard
42 Disassembly and reassembly
eoptical drive
fbattery
4 Follow the procedure in After working inside your computer.
Camera
Removing the camera
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
ckeyboard
dbase cover
eWLAN card
fdisplay assembly
gdisplay bezel
3 To remove the camera:
a Disconnect the camera cable from the camera [1].
b Remove the camera from the display assembly [2].
Installing the camera
1 Install the camera into the slot on the display assembly.
2 Connect the camera cable.
3 Install the:
Disassembly and reassembly 43
adisplay bezel
bdisplay assembly
cWLAN Card
dbase cover
ekeyboard
foptical drive
gbattery
4 Follow the procedure in After working inside your computer.
Display panel
Removing the display panel
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
ckeyboard
dbase cover
eWLAN card
fdisplay assembly
gdisplay bezel
3 To remove the display panel:
a Remove the M2.5L8 screws that secure the display panel to the display assembly [1].
b Lift the display panel to access the cables underneath [2].
4 To disconnect the cable:
44 Disassembly and reassembly
a Remove the tape that secures the eDP cable to the display panel [1].
b Lift the locking tab and remove the eDP cable [2].
c Remove the display panel from the computer [3].
Installing the display panel
1 Connect the eDP cable to the display panel.
2 Ax the tape to secure the display cable.
3 Place the display panel on the display assembly.
4 Tighten the M2.5L8 screws to secure the display panel to the display assembly.
5 Install the:
adisplay bezel
bdisplay assembly
cWLAN Card
dbase cover
ekeyboard
foptical drive
gbattery
6 Follow the procedure in After working inside your computer.
Display hinges
Removing the display hinges
1 Follow the procedure in Before working inside your computer.
2 Remove the:
Disassembly and reassembly 45
abattery
boptical drive
ckeyboard
dbase cover
eWLAN card
fdisplay assembly
gdisplay bezel
hdisplay panel
3 To remove the hinges:
a Remove the six M2.5L2.5 screws that secure the display hinges to the display assembly [1].
b Remove the display hinges [2].
Installing the display hinges
1 Tighten the six M2.5L2.5 screws to secure the display hinges to the display assembly.
2 Install the:
adisplay panel
bdisplay bezel
cdisplay assembly
dWLAN Card
ebase cover
fkeyboard
goptical drive
hbattery
3 Follow the procedure in After working inside your computer.
46 Disassembly and reassembly
Palm rest
Replacing the palmrest
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abattery
boptical drive
ckeyboard
dbase cover
ehard drive assembly
fngerprint reader
gWLAN card
hmemory module
ipower button board
jheat sink
ksystem fan
lspeaker
mI/O board
npower connector port
osystem board
pdisplay assembly
NOTE: The component you are left with is the palmrest.
Disassembly and reassembly 47
Installing the palmrest
1 Place the palmrest.
2 Install the:
adisplay assembly
bsystem board
cpower connector port
dI/O board
espeaker
fsystem fan
gheat sink
hpower button board
imemory module
jWLAN Card
kngerprint reader
lhard drive assembly
mbase cover
nkeyboard
ooptical drive
pbattery
3 Follow the procedure in After working inside your computer.
48 Disassembly and reassembly
Technology and components
Processors
This laptop is shipped with Intel 6th generation processor:
• Intel Celeron
• Intel i5 series
NOTE: The clock speed and performance varies depending on the workload and other variables.
Identifying processors in Windows 10
1 Tap Search the Web and Windows.
2 Type Device Manager.
3 Tap Processor.
The basic information of the processor is displayed.
Identifying processors in Windows 8
1 Tap Search the Web and Windows.
2 Type Device Manager.
3 Tap Processor.
3
Technology and components 49
The basic information of the processor is displayed.
Identifying processors in Windows 7
1 Click Start > Control Panel > Device Manager.
2 Select Processor.
The basic information of the processor is displayed.
50 Technology and components
Verifying the processor usage in Task Manager
1 Press and hold the taskbar.
2 Select Start Task Manager.
The Windows Task Manager window is displayed.
3 Click the Performance tab in the Windows Task Manager window.
The processor performance details are displayed.
Verifying the processor usage in Resource Monitor
1 Press and hold the taskbar.
2 Select Start Task Manager.
The Windows Task Manager window is displayed.
3 Click the Performance tab in the Windows Task Manager window.
The processor performance details are displayed.
4 Click Open Resource Monitor.
Technology and components 51
Chipsets
All laptops communicate with the CPU through the chipset. This laptop is shipped with the Intel 100 Series chipset.
Downloading the chipset driver
1 Turn on the laptop.
2 Go to Dell.com/support.
3 Click Product Support, enter the Service Tag of your laptop, and then click Submit.
NOTE: If you do not have the Service Tag, use the autodetect feature or manually browse for your laptop model.
4 Click Drivers and Downloads.
5 Select the operating system installed in your laptop.
6 Scroll down the page, expand Chipset, and select your chipset driver.
7 Click Download File to download the latest version of the chipset driver for your laptop.
8 After the download is complete, navigate to the folder where you saved the driver le.
9 Double-click the chipset driver le icon and follow the instructions on the screen.
Identifying the chipset in Device Manager on Windows 10
1 Click All Settings on the Windows 10 Charms Bar.
2 From the Control Panel, select Device Manager.
3 Expand System Devices and search for the chipset.
Identifying chipset in Device Manager on Windows 8
1 Click Settings on the Windows 8.1 Charms Bar.
2 From the Control Panel, select Device Manager.
3 Expand System Devices and search for the chipset.
52 Technology and components
Identifying chipset in Device Manager on Windows 7
1 Click Start → Control Panel → Device Manager.
2 Expand System Devices and search for the chipset.
Technology and components 53
Intel chipset drivers
Verify if the Intel chipset drivers are already installed in the laptop.
Table 2. Intel chipset drivers
Before installation After installation
Graphics card
This laptop is shipped with the Intel HD Graphics 520 graphics chipset.
Intel HD Graphics drivers
Verify if the Intel HD Graphics drivers are already installed in the laptop.
Table 3. Intel HD Graphics drivers
Before installation After installation
54 Technology and components
Intel HD Graphics 520
The Intel HD Graphics 520 (GT2) is an integrated graphics unit, which can be found in various ULV (Ultra Low Voltage) processors of the
Skylake generation. This GT2 version of the Skylake GPU oers 24 Execution Units (EUs) clocked at up to 1050 MHz (depending on the
CPU model). Due to its lack of dedicated graphics memory or eDRAM cache, the HD 520 has to access the main memory (2x 64-bit
DDR3L-1600/DDR4-2133).
Performance
The exact performance of the HD Graphics 520 depends on various factors like L3 cache size, memory conguration (DDR3/DDR4) and
maximum clock rate of the specic model. The fastest versions Core i7-6600U should perform similar to a dedicated GeForce 820M and
handles modern games (as of 2015) in low settings.
Features
The revised video engine now decodes H.265/HEVC completely in hardware and more eciently than before. Displays can be connected
using a DP 1.2/eDP 1.3 (max. 3840 x 2160 @ 60 Hz), whereas HDMI is limited to the older version 1.4a (max. 3840 x 2160 @ 30 Hz).
However, HDMI 2.0 can be added using a DisplayPort converter. Up to three displays can be controlled simultaneously.
Power Consumption
The HD Graphics 520 can be found in mobile processors specied at 15 W TDP and is therefore suited for compact laptops and Ultrabooks.
Key Specications
The following table contains the key specications of the Intel HD Graphics 520:
Table 4. Key specications
Specication Intel HD Graphics 520
Codename Skylake GT2
Architecture Intel Gen 6 (Skylake)
Technology and components 55
Specication Intel HD Graphics 520
Pipelines 24 — unied
Core Speed 300 — 1050 (Boost) MHz
Memory Type DDR3/DDR4
Memory Bus Width 64/128 bit
Shared Memory Yes
Technology 14 nm
Features QuickSync
DirectX DirectX 12 (FL 12_1)
Max. Displays Supported Up to 3
DP 1.2/eDP 1.3 max. resolution 3840 x 2160 @ 60 Hz
HDMI max. resolution 3840 x 2160 @ 30 Hz
Display options
This laptop has a 14– inch HD with 1366 x 768 pixels resolution (maximum).
Identifying the display adapter
1 Start the Search Charm and select Settings.
2 Type Device Manager in the search box and tap Device Manager from the left pane.
3 Expand Display adapters.
The display adapters are displayed.
Rotating the display
1 Press and hold on the desktop screen.
56 Technology and components
A sub menu is displayed.
2 Select Graphic Options > Rotation and choose on of the following:
• Rotate to Normal
• Rotate to 90 Degrees
• Rotate to 180 Degrees
• Rotate to 270 Degrees
NOTE: The Display can also be rotated using the following key combinations:
• Ctrl + Alt + Up arrow key (Rotate to normal)
• Right arrow key (Rotate 90 degrees)
• Down arrow key (Rotate 180 degrees)
• Left arrow key (Rotate 270 degrees)
Downloading drivers
1 Turn on the laptop.
2 Go to Dell.com/support.
3 Click Product Support, enter the Service Tag of your laptop, and then click Submit.
NOTE: If you do not have the Service Tag, use the auto detect feature or manually browse for your laptop model.
4 Click Drivers and Downloads.
5 Select the operating system installed on your laptop.
6 Scroll down the page and select the graphic driver to install.
7 Click Download File to download the graphic driver for your laptop.
8 After the download is complete, navigate to the folder where you saved the graphic driver le.
9 Double-click the graphic driver le icon and follow the instructions on the screen.
Changing the screen resolution
1 Press and hold the desktop screen and select Display Settings.
2 Tap or click Advanced display settings.
3 Select the required resolution from the drop-down list and tap Apply.
Technology and components 57
Adjusting brightness in Windows 10
To enable or disable automatic screen brightness adjustment:
1 Swipe-in from the right edge of the display to access the Action Center.
2 Tap or click All Settings → System → Display.
3 Use the Adjust my screen brightness automatically slider to enable or disable automatic-brightness adjustment.
NOTE: You can also use the Brightness level slider to adjust the brightness manually.
Adjusting brightness in Windows 8
To enable or disable automatic screen brightness adjustment:
1 Swipe-in from the right edge of the display to access the Charms menu.
2 Tap or click Settings → Change PC Settings → PC and devices→ Power and sleep.
3 Use the Adjust my screen brightness automatically slider to enable or disable automatic-brightness adjustment.
Adjusting brightness in Windows 7
To enable or disable automatic screen brightness adjustment:
1 Click Start → Control Panel → Display.
2 Use the Adjust brightness slider to enable or disable automatic-brightness adjustment.
NOTE: You can also use the Brightness level slider to adjust the brightness manually.
Cleaning the display
1 Check for any smudges or areas that has to be cleaned.
2 Use a microber cloth to remove any obvious dust and gently brush o any dirt particles.
3 Proper cleaning kits should be used to clean and keep your display in a crisp, clear, and pristine condition.
NOTE: Never spray any cleaning solutions directly on the screen; spray it to the cleaning cloth.
4 Gently wipe the screen in a circular motion. Do not press hard on the cloth.
NOTE: Do not press hard or touch the screen with your ngers or you may leave oily prints and smears.
NOTE: Do not leave any liquid on the screen.
5 Remove all excess moisture as it may damage your screen.
6 Let the display dry thoroughly before you turn it on.
7 For stains that are hard to remove, repeat this procedure till the display is clean.
58 Technology and components
Connecting to external display devices
Follow these steps to connect your laptop to an external display device:
1 Ensure that the projector is turned on and plug the projector cable into a video port on your laptop.
2 Press the Windows logo+P key.
3 Select one of the following modes:
• PC screen only
• Duplicate
• Extend
• Second Screen only
NOTE: For more information, see the document that shipped with your display device.
Hard drive options
This laptop supports SATA drives and SSDs.
Identifying the hard drive in Windows 10
1 Tap or click All Settings on the Windows 10 Charms Bar.
2 Tap or click Control Panel, select Device Manager , and expand Disk drives.
The hard drive is listed under Disk drives.
Identifying the hard drive in Windows 8
1 Tap or click Settings on the Windows 8 Charms Bar.
2 Tap or click Control Panel, select Device Manager, and expand Disk drives.
The hard drive is listed under Disk drives.
Technology and components 59
Identifying the hard drive in Windows 7
1 Click Start > Control Panel > Device Manager.
The hard drive is listed under Disk drives.
2 Expand Disk drives.
Entering BIOS setup
1 Turn on or restart your laptop.
2 When the Dell logo appears, perform one of the following actions to enter the BIOS setup program:
• With keyboard — Tap F2 until the Entering BIOS setup message appears. To enter the Boot selection menu, tap F12.
• Without keyboard — When the F12 boot selection menu is displayed, press the Volume Down button to enter BIOS setup. To
enter the Boot selection menu, press the Volume Up button.
Hard drive is listed under the System Information under the General group.
USB features
Universal Serial Bus, or USB, was introduced in 1996. It dramatically simplied the connection between host computers and peripheral
devices like mice, keyboards, external drivers, and printers.
Let's take a quick look on the USB evolution referencing to the table below.
Table 5. USB evolution
Type Data Transfer Rate Category Introduction Year
USB 2.0 480 Mbps High Speed 2000
USB 3.0/USB 3.1 Gen 1 5 Gbps Super Speed 2010
USB 3.1 Gen 2 10 Gbps Super Speed 2013
USB 3.0/USB 3.1 Gen 1 (SuperSpeed USB)
For years, the USB 2.0 has been rmly entrenched as the de facto interface standard in the PC world with about 6 billion devices sold, and
yet the need for more speed grows by ever faster computing hardware and ever greater bandwidth demands. The USB 3.0/USB 3.1 Gen 1
60 Technology and components
nally has the answer to the consumers' demands with a theoretically 10 times faster than its predecessor. In a nutshell, USB 3.1 Gen 1
features are as follows:
• Higher transfer rates (up to 5 Gbps)
• Increased maximum bus power and increased device current draw to better accommodate power-hungry devices
• New power management features
• Full-duplex data transfers and support for new transfer types
• Backward USB 2.0 compatibility
• New connectors and cable
The topics below cover some of the most commonly asked questions regarding USB 3.0/USB 3.1 Gen 1.
Speed
Currently, there are 3 speed modes dened by the latest USB 3.0/USB 3.1 Gen 1 specication. They are Super-Speed, Hi-Speed and Full-
Speed. The new SuperSpeed mode has a transfer rate of 4.8Gbps. While the specication retains Hi-Speed, and Full-Speed USB mode,
commonly known as USB 2.0 and 1.1 respectively, the slower modes still operate at 480Mbps and 12Mbps respectively and are kept to
maintain backward compatibility.
USB 3.0/USB 3.1 Gen 1 achieves the much higher performance by the technical changes below:
• An additional physical bus that is added in parallel with the existing USB 2.0 bus (refer to the picture below).
• USB 2.0 previously had four wires (power, ground, and a pair for dierential data); USB 3.0/USB 3.1 Gen 1 adds four more for two pairs
of dierential signals (receive and transmit) for a combined total of eight connections in the connectors and cabling.
• USB 3.0/USB 3.1 Gen 1 utilizes the bidirectional data interface, rather than USB 2.0's half-duplex arrangement. This gives a 10-fold
increase in theoretical bandwidth.
With today's ever increasing demands placed on data transfers with high-denition video content, terabyte storage devices, high megapixel
count digital cameras etc., USB 2.0 may not be fast enough. Furthermore, no USB 2.0 connection could ever come close to the 480Mbps
theoretical maximum throughput, making data transfer at around 320Mbps (40MB/s) — the actual real-world maximum. Similarly, USB
3.0/USB 3.1 Gen 1 connections will never achieve 4.8Gbps. We will likely see a real-world maximum rate of 400MB/s with overheads. At this
speed, USB 3.0/USB 3.1 Gen 1 is a 10x improvement over USB 2.0.
Technology and components 61
Applications
USB 3.0/USB 3.1 Gen 1 opens up the laneways and provides more headroom for devices to deliver a better overall experience. Where USB
video was barely tolerable previously (both from a maximum resolution, latency, and video compression perspective), it's easy to imagine
that with 5-10 times the bandwidth available, USB video solutions should work that much better. Single-link DVI requires almost 2Gbps
throughput. Where 480Mbps was limiting, 5Gbps is more than promising. With its promised 4.8Gbps speed, the standard will nd its way
into some products that previously weren't USB territory, like external RAID storage systems.
Listed below are some of the available SuperSpeed USB 3.0/USB 3.1 Gen 1 products:
• External Desktop USB 3.0/USB 3.1 Gen 1 Hard Drives
• Portable USB 3.0/USB 3.1 Gen 1 Hard Drives
• USB 3.0/USB 3.1 Gen 1 Drive Docks & Adapters
• USB 3.0/USB 3.1 Gen 1 Flash Drives & Readers
• USB 3.0/USB 3.1 Gen 1 Solid-state Drives
• USB 3.0/USB 3.1 Gen 1 RAIDs
• Optical Media Drives
• Multimedia Devices
• Networking
• USB 3.0/USB 3.1 Gen 1 Adapter Cards & Hubs
Compatibility
The good news is that USB 3.0/USB 3.1 Gen 1 has been carefully planned from the start to peacefully co-exist with USB 2.0. First of all,
while USB 3.0/USB 3.1 Gen 1 species new physical connections and thus new cables to take advantage of the higher speed capability of
the new protocol, the connector itself remains the same rectangular shape with the four USB 2.0 contacts in the exact same location as
before. Five new connections to carry receive and transmitted data independently are present on USB 3.0/USB 3.1 Gen 1 cables and only
come into contact when connected to a proper SuperSpeed USB connection.
Windows 8/10 will be bringing native support for USB 3.1 Gen 1 controllers. This is in contrast to previous versions of Windows, which
continue to require separate drivers for USB 3.0/USB 3.1 Gen 1 controllers.
Microsoft announced that Windows 7 would have USB 3.1 Gen 1 support, perhaps not on its immediate release, but in a subsequent Service
Pack or update. It is not out of the question to think that following a successful release of USB 3.0/USB 3.1 Gen 1 support in Windows 7,
SuperSpeed support would trickle down to Vista. Microsoft has conrmed this by stating that most of their partners share the opinion that
Vista should also support USB 3.0/USB 3.1 Gen 1.
HDMI 1.4
This topic explains the HDMI 1.4 and its features along with the advantages.
HDMI (High-Denition Multimedia Interface) is an industry-supported, uncompressed, all-digital audio/video interface. HDMI provides an
interface between any compatible digital audio/video source, such as a DVD player, or A/V receiver and a compatible digital audio and/or
video monitor, such as a digital TV (DTV). The intended applications for HDMI TVs, and DVD players. The primary advantage is cable
reduction and content protection provisions. HDMI supports standard, enhanced, or high-denition video, plus multichannel digital audio on
a single cable.
NOTE: The HDMI 1.4 will provide 5.1 channel audio support.
62 Technology and components
HDMI 1.4 Features
•HDMI Ethernet Channel - Adds high-speed networking to an HDMI link, allowing users to take full advantage of their IP-enabled
devices without a separate Ethernet cable
•Audio Return Channel - Allows an HDMI-connected TV with a built-in tuner to send audio data "upstream" to a surround audio system,
eliminating the need for a separate audio cable
•3D - Denes input/output protocols for major 3D video formats, paving the way for true 3D gaming and 3D home theater applications
•Content Type - Real-time signaling of content types between display and source devices, enabling a TV to optimize picture settings
based on content type
•Additional Color Spaces - Adds support for additional color models used in digital photography and computer graphics
•4K Support - Enables video resolutions far beyond 1080p, supporting next-generation displays that will rival the Digital Cinema systems
used in many commercial movie theaters
•HDMI Micro Connector - A new, smaller connector for phones and other portable devices, supporting video resolutions up to 1080p
•Automotive Connection System - New cables and connectors for automotive video systems, designed to meet the unique demands of
the motoring environment while delivering true HD quality
Advantages of HDMI
• Quality HDMI transfers uncompressed digital audio and video for the highest, crispest image quality.
• Low -cost HDMI provides the quality and functionality of a digital interface while also supporting uncompressed video formats in a
simple, cost-eective manner
• Audio HDMI supports multiple audio formats from standard stereo to multichannel surround sound
• HDMI combines video and multichannel audio into a single cable, eliminating the cost, complexity, and confusion of multiple cables
currently used in A/V systems
• HDMI supports communication between the video source (such as a DVD player) and the DTV, enabling new functionality
USB Powershare
USB PowerShare is a feature which allows for external USB devices (i.e. cellular phones, portable music players, etc.) to charge using the
portable system's battery.
Only the USB connector with a SS+USB+Battery--> icon, can be used.
This functionality is enabled in the system setup under the On Board Devices heading. You can select how much of the battery's charge
can be used as well (pictured below). If you set the USB PowerShare to 25%, the external device is allowed to charge until the battery
reaches 25% of full capacity (e.g. 75% of the portable's battery charge is used up).
Technology and components 63
Camera features
This laptop comes with front-facing camera with the image resolution of 1280 x 720 (maximum).
Identifying the camera in Device Manager on Windows 10
1 In the Search box, type device manager, and tap to start it.
2 Under Device Manager, expand Imaging devices.
Identifying the camera in Device Manager on Windows 8
1 Start the Charms Bar from the desktop interface.
2 Select Control Panel.
3 Select Device Manager and expand Imaging devices.
Identifying the camera in Device Manager on Windows 7
1 Click Start > Control Panel > Device Manager.
2 Expand Imaging devices.
Starting the camera
To start the camera, open an application that uses the camera. For instance, if you tap the Dell webcam central software or the Skype
software that is shipped with the laptop, the camera turns on. Similarly, if you are chatting on the internet and the application requests to
access the webcam, the webcam turns on.
64 Technology and components
Starting the camera app
1 Tap or click the Windows button and select All apps.
2 Select Camera from the apps list.
3 If the Camera App is not available in the apps list, search for it.
Technology and components 65
Memory features
This Laptop supports 4 GB to 16 GB, 2400 MHz DDR4 SoDIMM (2 slots)
Verifying system memory
Windows 10
1 Tap the Windows button and select All Settings > System .
2 Under System, tap About.
Verifying system memory in setup
1 Turn on or restart your laptop.
2 Perform one of the following actions after the Dell logo is displayed:
• With keyboard — Tap F2 until the Entering BIOS setup message appears. To enter the Boot selection menu, tap F12.
• Without keyboard — When the F12 boot selection menu is displayed, press the Volume Down button to enter BIOS setup. To
enter the Boot selection menu, press the Volume Up button.
3 On the left pane, select Settings > General > System Information,
The memory information is displayed on the right pane.
Testing memory using ePSA
1 Turn on or restart your laptop.
2 Perform one of the following actions after the Dell logo is displayed:
• With keyboard — Press F2.
• Without keyboard — Press and hold the Volume Up button when the Dell logo is displayed on the screen. When the F12 boot
selection menu is displayed, select Diagnostics from the boot menu, and press Enter.
The PreBoot System Assessment (PSA) starts on your laptop.
NOTE: If you wait too long and the operating system logo appears, continue to wait until you see the desktop. Turn o the
laptop and try again.
Audio drivers
Verify if the Realtek audio drivers are already installed in the laptop.
Table 6. Realtek HD audio drivers
Before installation After installation
66 Technology and components
System setup
System setup enables you to manage your hardware and specify BIOS level options. From the System setup, you can:
• Change the NVRAM settings after you add or remove hardware
• View the system hardware conguration
• Enable or disable integrated devices
• Set performance and power management thresholds
• Manage your computer security
Topics:
• Boot Sequence
• Navigation keys
• System setup options
• Updating the BIOS in Windows
• System and setup password
Boot Sequence
Boot Sequence allows you to bypass the System Setup–dened boot device order and boot directly to a specic device (for example:
optical drive or hard drive). During the Power-on Self Test (POST), when the Dell logo appears, you can:
• Access System Setup by pressing F2 key
• Bring up the one-time boot menu by pressing F12 key
The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot menu options are:
• Removable Drive (if available)
• STXXXX Drive
NOTE: XXX denotes the SATA drive number.
• Optical Drive (if available)
• SATA Hard Drive (if available)
• Diagnostics
NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.
The boot sequence screen also displays the option to access the System Setup screen.
Navigation keys
NOTE: For most of the System Setup options, changes that you make are recorded but do not take eect until you restart the
system.
Keys Navigation
Up arrow Moves to the previous eld.
Down arrow Moves to the next eld.
4
System setup 67
Keys Navigation
Enter Selects a value in the selected eld (if applicable) or follow the link in the eld.
Spacebar Expands or collapses a drop-down list, if applicable.
Tab Moves to the next focus area.
NOTE: For the standard graphics browser only.
Esc Moves to the previous page until you view the main screen. Pressing Esc in the main screen displays a message
that prompts you to save any unsaved changes and restarts the system.
System setup options
NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not appear.
Table 7. General tab
Option Description
System Information This section lists the primary hardware features of your computer.
• System Information: Displays BIOS Version, Service Tag, Asset Tag, Ownership Tag, Ownership Date,
Manufacture Date, and the Express Service Code.
• Memory Information: Displays Memory Installed, Memory Available, Memory Speed, Memory Channels Mode,
Memory Technology, DIMM A Size, DIMM B Size,
• Processor Information: Displays Processor Type, Core Count, Processor ID, Current Clock Speed, Minimum
Clock Speed, Maximum Clock Speed, Processor L2 Cache, Processor L3 Cache, HT Capable, and 64-Bit
Technology.
• Device Information: Displays Primary Hard Drive, ODD Device, LOM MAC Address, Video Controller, Video
BIOS Version, Video Memory, Panel Type, Native Resolution, Audio Controller, Wi-Fi Device, Bluetooth Device.
Battery Information Displays the battery status and the type of AC adapter connected to the computer.
Boot Sequence Boot Sequence Allows you to change the order in which the computer
attempts to nd an operating system. The option is:
• Windows Boot Manager
By default, all the options are checked. You can also
deselect any option or change the boot order.
Boot List Option Allows you to change the boot list option.
• Legacy
• UEFI
Advanced Boot
Options
This option allows you the legacy option ROMs to load. By default, the Enable Legacy Option ROMs is disabled.
Date/Time Allows you to change the date and time.
Table 8. System Conguration
Option Description
Integrated NIC Allows you to congure the integrated network controller. The options are:
• Disabled
• Enabled
68 System setup
Option Description
• Enabled w/PXE: This option is enabled by default.
SATA Operation Allows you to congure the internal SATA hard-drive controller. The options are:
• Disabled
• AHCI: This option is enabled by default.
Drives Allows you to congure the SATA drives on board. All drives are enabled by default. The options
are:
• SATA-0: This option is selected by default.
• SATA-1: This option is selected by default.
SMART Reporting This eld controls whether hard drive errors for integrated drives are reported during system
startup. This technology is part of the SMART (Self-Monitoring Analysis and Reporting
Technology) specication. This option is disabled by default.
• Enable SMART Reporting
USB Conguration This eld congures the integrated USB controller. If Boot Support is enabled, the system is
allowed to boot any type of USB Mass Storage Devices (HDD, memory key, oppy).
If USB port is enabled, device attached to this port is enabled and available for OS.
If USB port is disabled, the OS cannot see any device attached to this port.
• Enable Boot Support
• Enable External USB Port
NOTE: USB keyboard and mouse always work in the BIOS setup irrespective of these
settings.
Audio This eld enables or disables the integrated audio controller. By default, the Enable Audio option
is selected. The options are:
• Enable Microphone
• Enable Internal Speaker
Unobtrusive Mode: This eld enables or disables all light and sound emissions in the system. By default option is
disabled.
Miscellaneous Devices Allows you to enable or disable the following devices:
• Enable Camera
• Enabled Secure Digital (SD) Card
NOTE: All devices are enabled by default.
Table 9. Video
Option Description
LCD Brightness Allows you to set the display brightness depending up on the power source (On Battery and On
AC).
NOTE: The Video setting will only be visible when a video card is installed into the
system.
System setup 69
Table 10. Security
Option Description
Admin Password Allows you to set, change, or delete the administrator (admin) password.
NOTE: You must set the admin password before you set the system or hard drive
password. Deleting the admin password automatically deletes the system password
and the hard drive password.
NOTE: Successful password changes take eect immediately.
Default Setting: Not set
System Password Allows you to set, change or delete the system password.
NOTE: Successful password changes take eect immediately.
Default Setting: Not set
Internal HDD-0 Password Allows you to set, change or delete the password on the system's internal hard-disk drive.
NOTE: Successful password changes take eect immediately.
Default Setting: Not set
Strong Password Allows you to enforce the option to always set strong passwords.
Default Setting: Enable Strong Password is not selected.
NOTE: If Strong Password is enabled, Admin and System passwords must contain at
least one uppercase character, one lowercase character and be at least 8 characters
long.
Password Conguration Allows you to determine the minimum and maximum length of Administrator and System
passwords.
Password Bypass Allows you to enable or disable the permission to bypass the System and the Internal HDD
password, when they are set. The options are:
• Disabled
• Reboot bypass
Default Setting: Disabled
Password Change Allows you to enable the disable permission to the System and Hard Drive passwords when the
admin password is set.
Default Setting: Allow Non-Admin Password Changes is selected.
Non-Admin Setup Changes Allows you to determine whether changes to the setup options are allowed when an
Administrator Password is set. If disabled the setup options are locked by the admin password.
UEFI Capsule Firmware Updates Allows you to controls whether the system allows BIOS update via UEFI capsule update
packages. Default setting: Enable
TPM 2.0 Security Allows you to enable the Trusted Platform Module (TPM) during POST. The options are:
• TPM On (enabled by default)
• Clear
• PPI Bypass for Enabled Commands
• PPI Bypass for Disabled Commands
• Attestation Enable (enabled by default)
• Key Storage Enable (enabled by default)
• SHA-256 (enabled by default)
• Disabled
70 System setup
Option Description
• Enabled
NOTE: To upgrade or downgrade TPM1.2/2.0, download the TPM wrapper tool
(software).
Computrace Allows you to activate or disable the optional Computrace software The options are:
• Deactivate
• Disable
• Activate
NOTE: The Activate and Disable options will permanently activate or disable the
feature and no further changes will be allowed.
Default setting: Deactivate
CPU XD Support Allows you to enable the Execute Disable mode of the processor.
Enable CPU XD Support (default)
Admin Setup Lockout Allows you to prevent users from entering Setup when an Administrator password is set.
Default Setting: Enable Admin Setup Lockout is not selected.
Table 11. Secure Boot
Option Description
Secure Boot Enable This option enables or disables the Secure Boot Feature.
• Disabled
• Enabled
Default Setting: The option is disabled.
Expert Key Management Allows you to manipulate the security key databases only if the system is in Custom Mode. The
Enable Custom Mode option is disabled by default. The options are:
• PK
• KEK
• db
• dbx
If you enable the Custom Mode, the relevant options for PK, KEK, db, and dbx appear. The
options are:
•Save to File- Saves the key to a user-selected le
•Replace from File- Replaces the current key with a key from a user-selected le
•Append from File- Adds a key to the current database from a user-selected le
•Delete- Deletes the selected key
•Reset All Keys- Resets to default setting
•Delete All Keys- Deletes all the keys
NOTE: If you disable the Custom Mode, all the changes made will be erased and the
keys will restore to default settings.
System setup 71
Table 12. Intel Software Guard Extensions screen options
Option Description
Intel SGX Enable This eld species you to provide a secured environment for
running code/storing sensitive information in the context of the
main OS. The options are:
• Disabled
• Enabled
Default setting: Disabled
Enclave Memory Size This option sets SGX Enclave Reserve Memory Size. The options
are:
• 32 MB
• 64 MB
• 128 MB
Table 13. Performance
Option Description
Multi Core Support This eld species whether the process will have one or all cores enabled. The performance of
some applications will improve with the additional cores. This option is enabled by default. Allows
you to enable or disable multi-core support for the processor. The installed processor supports
two cores. If you enable Multi Core Support, two cores will be enabled. If you disable Multi Core
Support, one core will be enabled.
• Enable Multi Core Support
Default Setting: The option is enabled.
Intel SpeedStep Allows you to enable or disable the Intel SpeedStep feature.
• Enable Intel SpeedStep
Default Setting: The option is enabled.
C States Control Allows you to enable or disable the additional processor sleep states.
• C states
Default Setting: The option is enabled.
Intel TurboBoost Allows you to enable or disable the Intel TurboBoost mode of the processor.
• Enable Intel TurboBoost
Default Setting: The option is enabled.
Hyper-Thread Control Allows you to enable or disable the HyperThreading in the processor.
• Disabled
• Enabled
Default Setting: The option is enabled.
72 System setup
Table 14. Power Management
Option Description
AC Behavior Allows you to enable or disable the computer from turning on automatically when an AC adapter
is connected.
Default Setting: Wake on AC is not selected.
Auto On Time Allows you to set the time at which the computer must turn on automatically. The options are:
• Disabled (default)
• Every Day
• Weekdays
• Select Days
USB Wake Support Allows you to enable USB devices to wake the system from Standby.
NOTE: This feature is only functional when the AC power adapter is connected. If the
AC power adapter is removed during Standby, the system setup will remove power
from all of the USB ports to conserve battery power.
• Enable USB Wake Support
Default Setting: The option is disabled.
Wake on LAN Allows you to enable or disable the feature that powers on the computer from the O state
when triggered by a LAN signal.
• Disabled: This option is enabled by default
• LAN Only
Primary Battery Charge Conguration Allows you to select the charging mode for the battery. The options are:
• Adaptive
• Standard — Fully charges your battery at a standard rate.
• Primarily AC use
• Custom
If Custom Charge is selected, you can also congure Custom Charge Start and Custom Charge
Stop.
NOTE: All charging mode may not be available for all the batteries. To enable this
option, disable the Advanced Battery Charge Conguration option.
Table 15. POST Behavior
Option Description
Adapter Warnings Allows you to enable or disable the system setup (BIOS) warning messages when you use
certain power adapters.
Default Setting: Enable Adapter Warnings
Fn Lock Option Allows the hot key combination <Fn> +<Esc> toggle the primary behavior of F1–F12, between
the standard and secondary functions.
• Lock Mode Disable/Standard. This option is enabled by default.
• Lock Mode Enable/Secondary
Fastboot Allows you to speed up the boot process by bypassing some of the compatibility steps. The
options are:
System setup 73
Option Description
• Minimal
• Thorough (default)
• Auto
Extended BIOS POST Time Allows you to create an additional preboot delay. The options are:
• 0 seconds. This option is enabled by default.
• 5 seconds
• 10 seconds
Table 16. Virtualization Support
Option Description
Virtualization Allows you to enable or disable the Intel Virtualization Technology.
•Enable Intel Virtualization Technology (default)
VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the additional hardware
capabilities provided by Intel® Virtualization technology for direct I/O.
Enable VT for Direct I/O — enabled by default.
Table 17. Wireless
Option Description
Wireless Switch Allows to set the wireless devices that can be controlled by the wireless
switch. The options are:
• WLAN
• Bluetooth
All the options are enabled by default.
Wireless Device Enable Allows you to enable or disable the internal wireless devices.
• WLAN
• Bluetooth
All the options are enabled by default.
Table 18. Maintenance
Option Description
Service Tag Displays the Service Tag of your computer.
Asset Tag Allows you to create a system asset tag if an asset tag is not already set. This option is not set
by default.
BIOS Downgrade This eld controls ashing of the system rmware to pervious revisions.
Allows BIOS Downgrade (Enabled by default)
Data Wipe This eld enables user to erase data from all internal storage device.
74 System setup
Option Description
BIOS Recovery Allows you to recover from certain corrupted BIOS conditions from a recover le on the user
primary hard drive or an external USB key. Enabled by default.
Table 19. System Logs
Option Description
BIOS Events Allows you to view and clear the System Setup (BIOS) POST events.
Thermal Events Allows you to view and clear the System Setup (Thermal) POST events.
Power Events Allows you to view and clear the System Setup (Power) POST events.
Table 20. SupportAssist System Resolution
Option Description
Auto OS Recovery Threshold Allows you to control the automatic boot ow for SupportAssist System. Options are:
•O
• 1
• 2 (Enabled by default)
• 3
SupportAssist OS Recovery Allows you to recover the SupportAssist OS Recovery (Disabled by default)
Updating the BIOS in Windows
It is recommended to update your BIOS (System Setup), when you replace the system board or if an update is available.
NOTE: If BitLocker is enabled, it must be suspended prior to updating the system BIOS, and then re-enabled after the BIOS
update is completed.
1 Restart the computer.
2 Go to Dell.com/support.
• Enter the Service Tag or Express Service Code and click Submit.
• Click Detect Product and follow the instructions on screen.
3 If you are unable to detect or nd the Service Tag, click Choose from all products.
4 Choose the Products category from the list.
NOTE: Choose the appropriate category to reach the product page
5 Select your computer model and the Product Support page of your computer appears.
6 Click Get drivers and click Drivers and Downloads.
The Drivers and Downloads section opens.
7 Click Find it myself.
8 Click BIOS to view the BIOS versions.
9 Identify the latest BIOS le and click Download.
10 Select your preferred download method in the Please select your download method below window, click Download File.
The File Download window appears.
11 Click Save to save the le on your computer.
12 Click Run to install the updated BIOS settings on your computer.
Follow the instructions on the screen.
System setup 75
System and setup password
Table 21. System and setup password
Password type Description
System password Password that you must enter to log on to your system.
Setup password Password that you must enter to access and make changes to the
BIOS settings of your computer.
You can create a system password and a setup password to secure your computer.
CAUTION: The password features provide a basic level of security for the data on your computer.
CAUTION: Anyone can access the data stored on your computer if it is not locked and left unattended.
NOTE: System and setup password feature is disabled.
Assigning a system setup password
You can assign a new System or Admin Password only when the status is in Not Set.
To enter the system setup, press F2 immediately after a power-on or re-boot.
1 In the System BIOS or System Setup screen, select Security and press Enter.
The Security screen is displayed.
2 Select System/Admin Password and create a password in the Enter the new password eld.
Use the following guidelines to assign the system password:
• A password can have up to 32 characters.
• The password can contain the numbers 0 through 9.
• Only lower case letters are valid, upper case letters are not allowed.
• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).
3 Type the system password that you entered earlier in the Conrm new password eld and click OK.
4 Press Esc and a message prompts you to save the changes.
5 Press Y to save the changes.
The computer reboots.
Deleting or changing an existing system setup password
Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing System and/or
Setup password. You cannot delete or change an existing System or Setup password, if the Password Status is Locked.
To enter the System Setup, press F2 immediately after a power-on or reboot.
1 In the System BIOS or System Setup screen, select System Security and press Enter.
The System Security screen is displayed.
2 In the System Security screen, verify that Password Status is Unlocked.
3 Select System Password, alter or delete the existing system password and press Enter or Tab.
4 Select Setup Password, alter or delete the existing setup password and press Enter or Tab.
NOTE: If you change the System and/or Setup password, re-enter the new password when prompted. If you delete the
System and/or Setup password, conrm the deletion when prompted.
76 System setup
5 Press Esc and a message prompts you to save the changes.
6 Press Y to save the changes and exit from System Setup.
The computer reboot.
System setup 77
Enhanced Pre-Boot System Assessment — ePSA
diagnostics
The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware. The ePSA is embedded with the
BIOS and is launched by the BIOS internally. The embedded system diagnostics provides a set of options for particular devices or device
groups allowing you to:
• Run tests automatically or in an interactive mode
• Repeat tests
• Display or save test results
• Run thorough tests to introduce additional test options to provide extra information about the failed device(s)
• View status messages that inform you if tests are completed successfully
• View error messages that inform you of problems encountered during testing
CAUTION: Use the system diagnostics to test only your computer. Using this program with other computers may cause invalid
results or error messages.
NOTE: Some tests for specic devices require user interaction. Always ensure that you are present at the computer terminal
when the diagnostic tests are performed.
Running the ePSA Diagnostics
Invoke diagnostics boot by either of the methods that are suggested below:
1 Power on the computer.
2 As the computer boots, press the F12 key when the Dell logo is displayed.
3 In the boot menu screen, use Up/Down arrow key to select the Diagnostics option and then press Enter.
NOTE: The Enhanced Pre-boot System Assessment window displays, listing all devices detected in the computer. The
diagnostics starts running the tests on all the detected devices.
4 Press the arrow in the lower-right corner to go to the page listing.
The detected items are listed and tested.
5 To run a diagnostic test on a specic device, press Esc and click Yes to stop the diagnostic test.
6 Select the device from the left pane and click Run Tests.
7 If there are any issues, error codes are displayed.
Note the error code and contact Dell.
5
78 Enhanced Pre-Boot System Assessment — ePSA diagnostics
Technical specications
NOTE: Oerings may vary by region. For more information regarding the conguration of your computer in:
• Windows 10, click or tap Start > Settings > System > About.
• Windows 8.1 and Windows 8, from the charms sidebar, click or tap Settings > Change PC settings. In the PC Settings window,
select PC and devices > PC Info.
• Windows 7, click Start , right-click My Computer, and then select Properties.
Table 22. System specications
Feature Specication
Chipset Skylake Celeron/ Intel Kaby Lake
DRAM bus width 64 bits
Flash EPROM 16 MB
Table 23. Processor specications
Feature Specication
Processor type • 7th Generation Intel Core i7-7500U (4M Cache, up to 3.50 GHz, 4 GT/s)
• 7th Generation Intel Core i5-7200U (3M Cache, up to 3.10 GHz, 4 GT/s)
• 7th Generation Intel Core i3-7100U (3M Cache, up to 2.40 GHz, 4 GT/s)
• 6th Generation Intel Core i3-6100U (3M Cache, up to 2.30 GHz, 4 GT/s)
• Intel Celeron 3855U
L1 cache 128 KB
L2 cache 512 KB
L3 cache Up to 4 MB
Table 24. Memory specications
Feature Specication
Memory connector Two internally accessible DDR4 connectors
Memory capacity 4 GB to 16 GB
Memory speed 2400 MHz
NOTE: If product is purchased with Intel® 6th Gen CPUs or 7th Gen
CPUs, the maximum memory speed achievable is 2133 MHz
Minimum memory 4 GB
Maximum memory 8-16 GB
6
Technical specications 79
Table 25. Storage specications
Feature Specication
SATA HDD 500GB , 1TB 5400RPM and 7200RPM SATA hard drive
Table 26. Audio specications
Feature Specication
Type Two channels high-denition audio
Controller Realtek ALC3246 with Waves MaxxAudio
Stereo conversion 24-bit (analog-to-digital and digital-to-analog)
Interface Intel HDA bus
Speakers 2 x 2 W
Volume controls Program menu and keyboard media-control keys
Table 27. Video specications
Feature Specication
Video type eDP
Video Controller:
UMA Intel HD Graphics (shared memory)
Discrete AMD Radeon R5 M315 (up to 2 GB DDR3)
Data bus: 64 bits
External display support VGA
Table 28. Camera specications
Feature Specication
Camera Resolution HD resolution
Video Resolution (maximum) Still image: HD resolution (1280x720)
Video: HD resolution (1280x720) at 30 fps (maximum)
Diagonal viewing angle 74°
Table 29. Communication specications
Feature Specication
Network adapter 10/100/1000 Mbps Ethernet LAN on Motherboard (LOM)
Wireless • Wi-Fi 802.11 b/g/n
• Bluetooth 4.0
80 Technical specications
Table 30. Ports and Connectors specications
Feature Specication
Audio One headphone/microphone combo port (headset)
Video VGA and HDMI out
Network adapter One RJ-45 port
USB: • Two USB 3.0 ports
• One USB 2.0 port
NOTE: The powered USB 3.0 connector also supports Microsoft Kernel Debugging. The ports are identied in the
documentation shipped with your computer.
Media card reader One SD slot
Table 31. Display specications
Feature Specication
Type 14.0 inches HD (non-touch)
Dimensions:
Height 320.90 mm (12.63 inches)
Diagonal 355.00 mm (14.00 inches)
Width 205.60 mm (8.09 inches)
Active area (X/Y) 320.90 mm x 205.60 mm (12.63 inches x 8.09 inches)
Maximum resolution 1366 x 768 pixels
Maximum brightness 220 nits
Operating angle 0° (closed) to 135°
Refresh rate 60 Hz
Minimum Viewing angles:
Horizontal 40° / 40°
Vertical 10° / 30°
Pixel pitch 0.2265 mm
Table 32. Keyboard specications
Feature Specication
Number of keys: US 80, Brazil 82, UK 81, and Japan 84
Backlit keyboard No
Layout Qwerty
Technical specications 81
Table 33. Touchpad specications
Feature Specication
Active Area:
X-axis 105.00 mm (4.13 inches)
Y-axis 65.00 mm (2.50 inches)
Multi-touch Supports ve ngers
Table 34. Battery specications
Feature Specication
Type • 4-cell “smart” lithium ion (40 and 47 WHr)
Dimensions:
Height 20.00 mm (0.78 inches)
Width 270.00 mm (10.63 inches)
Depth 37.50 mm (1.47 inches)
Weight 0.26 kg (0.56 lb)
Life span 300 discharge/charge cycles
Voltage 14.80 VDC
Temperature range:
Operating 0 °C to 35 °C (32 °F to 95 °F)
Non-Operating –40 °C to 65 °C (–40 °F to 149 °F)
Coin-cell battery 3 V CR2032 lithium ion
Table 35. AC Adapter specications
Feature Specication
Type 45 W
65 W
Input voltage 100 V AC to 240 V AC
Input frequency 50 Hz to 60 Hz
Input current (maximum)
45 W 1.30 A
65 W 1.70 A
Output current
45 W 2.31 A
65 W 3.34 A
Rated output voltage 19.50 V DC
82 Technical specications
Feature Specication
Temperature range:
Operating 0 °C to 40 °C (32 °F to 104 °F)
Non-Operating –40 °C to 70 °C (–40 °F to 158 °F)
Table 36. Physical specications
Feature Specication
Height 23.35 mm (0.91 inch)
Width 345.00 mm (13.58 inches)
Depth 243.00 mm (9.57 inches)
Weight 1.95 kg (4.20 lb)
Table 37. Environmental specications
Feature Specication
Temperature:
Operating 0 °C to 35 °C (32 °F to 95 °F)
Storage –40 °C to 65 °C (–40 °F to 149 °F)
Relative humidity (maximum):
Operating 10 % to 90 % (non-condensing)
Storage 0 % to 95 % (non-condensing)
Altitude (maximum):
Operating –15.2 m to 3048 m (–50 ft to 10,000 ft)
0° to 35°C
Non-Operating –15.2 m to 10,668 m (–50 ft to 35,000 ft)
Airborne contaminant level G1 as dened by ISA-S71.04-1985
Technical specications 83
Contacting Dell
NOTE: If you do not have an active Internet connection, you can nd contact information on your purchase invoice, packing slip,
bill, or Dell product catalog.
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services
may not be available in your area. To contact Dell for sales, technical support, or customer service issues:
1 Go to Dell.com/support.
2 Select your support category.
3 Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.
4 Select the appropriate service or support link based on your need.
7
84 Contacting Dell