Latitude 3520 Service Manual
Contents
Working inside your computer
- Safety instructions
Removing and installing components
Drivers and downloads
BIOS setup
Troubleshooting
Getting help and contacting Dell

DELL 3520 User Manual

Displayed below is the user manual for 3520 by DELL which is a product in the Notebooks category. This manual has pages.

Related Manuals

DELL 3520 Manual

Latitude 3520

Service Manual

Regulatory Model: P108F

Regulatory Type: P108F001/P108F002

April 2022

Rev. A03

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

trademarks may be trademarks of their respective owners.

Chapter 1: Working inside your computer...................................................................................... 7

Safety instructions.............................................................................................................................................................. 7

Before working inside your computer....................................................................................................................... 7

Entering Service Mode................................................................................................................................................. 8

Exiting Service Mode.................................................................................................................................................... 8

Safety precautions........................................................................................................................................................ 8

Electrostatic discharge—ESD protection............................................................................................................... 9

ESD field service kit ..................................................................................................................................................... 9

Transporting sensitive components.........................................................................................................................10

After working inside your computer........................................................................................................................ 10

Chapter 2: Removing and installing components...........................................................................11

Recommended tools...........................................................................................................................................................11

Screw List.............................................................................................................................................................................11

Major components of your system................................................................................................................................ 13

MicroSD-card......................................................................................................................................................................14

Removing the microSD-card..................................................................................................................................... 14

Installing the MicroSD-card....................................................................................................................................... 15

SIM card tray...................................................................................................................................................................... 15

Removing the SIM card tray..................................................................................................................................... 15

Installing the SIM card tray........................................................................................................................................16

Base cover........................................................................................................................................................................... 17

Removing the base cover...........................................................................................................................................17

Installing the base cover.............................................................................................................................................19

Battery cable...................................................................................................................................................................... 20

Lithium-ion battery precautions...............................................................................................................................20

Removing the battery cable...................................................................................................................................... 21

Installing the battery cable........................................................................................................................................22

Memory module................................................................................................................................................................. 22

Removing the memory module.................................................................................................................................22

Installing the memory module...................................................................................................................................23

M.2 solid-state drive.........................................................................................................................................................25

Removing the M.2 2230 solid-state drive............................................................................................................. 25

Installing the M.2 2230 solid-state drive............................................................................................................... 25

Removing the M.2 2280 solid-state drive............................................................................................................. 26

Installing the M.2 2280 solid-state drive............................................................................................................... 27

M.2 solid-state drive conversion bracket....................................................................................................................28

Replacing the M.2 solid-state drive conversion bracket................................................................................... 28

M.2 solid-state drive conversion plate.........................................................................................................................29

Removing the M.2 solid-state drive conversion plate........................................................................................ 29

Installing the M.2 solid-state drive conversion plate.......................................................................................... 30

Hard-disk drive assembly................................................................................................................................................. 31

Removing the hard-disk drive assembly................................................................................................................. 31

Removing the hard-disk drive bracket .................................................................................................................. 32

Contents

Contents 3

Installing the hard-disk drive bracket..................................................................................................................... 33

Installing the hard-disk drive assembly.................................................................................................................. 34

WLAN card..........................................................................................................................................................................35

Removing the WLAN card.........................................................................................................................................35

Installing the WLAN card........................................................................................................................................... 36

WWAN card........................................................................................................................................................................ 38

Removing the WWAN card....................................................................................................................................... 38

Installing the WWAN card......................................................................................................................................... 39

System fan..........................................................................................................................................................................40

Removing the system fan..........................................................................................................................................40

Installing the system fan.............................................................................................................................................41

Battery................................................................................................................................................................................. 42

Removing the 3-cell battery..................................................................................................................................... 42

Installing the 3-cell battery....................................................................................................................................... 43

Removing the 4-cell battery..................................................................................................................................... 45

Installing the 4-cell battery....................................................................................................................................... 46

I/O cable..............................................................................................................................................................................47

Removing the I/O cable............................................................................................................................................. 47

Installing the I/O cable............................................................................................................................................... 48

Display assembly................................................................................................................................................................48

Removing the display assembly............................................................................................................................... 48

Installing the display assembly.................................................................................................................................. 51

Heatsink assembly.............................................................................................................................................................53

Removing the heatsink assembly - for computers with discrete graphics card..........................................53

Installing the heatsink assembly - for computers with discrete graphics card............................................ 54

Removing the heatsink assembly - for computers with integrated graphics card......................................55

Installing the heatsink assembly - for computers with integrated graphics card........................................55

Power adapter port.......................................................................................................................................................... 56

Removing the power adapter port.......................................................................................................................... 56

Installing the power adapter port............................................................................................................................ 57

Coin-cell battery................................................................................................................................................................58

Removing the coin-cell battery................................................................................................................................58

Installing the coin-cell battery..................................................................................................................................59

USB cable............................................................................................................................................................................60

Removing the USB cable...........................................................................................................................................60

Installing the USB cable..............................................................................................................................................61

Ethernet port......................................................................................................................................................................62

Removing the ethernet port..................................................................................................................................... 62

Installing the ethernet port....................................................................................................................................... 63

I/O board.............................................................................................................................................................................64

Removing the I/O board............................................................................................................................................ 64

Installing the I/O board.............................................................................................................................................. 65

Power button..................................................................................................................................................................... 66

Removing the power button without fingerprint reader................................................................................... 66

Installing the power button without fingerprint reader...................................................................................... 67

Removing the power button with fingerprint reader..........................................................................................68

Installing the power button with fingerprint reader............................................................................................69

System board..................................................................................................................................................................... 69

Removing the system board - for computers with discrete graphics card...................................................69

Installing the system board - for computers with discrete graphics card..................................................... 72

4Contents

Removing the system board - for computers with integrated graphics card...............................................74

Installing the system board - for computers with integrated graphics card................................................. 77

Speakers.............................................................................................................................................................................. 79

Removing the speaker................................................................................................................................................ 79

Installing the speaker..................................................................................................................................................80

Touchpad ............................................................................................................................................................................ 81

Removing the touchpad............................................................................................................................................. 81

Installing the touchpad............................................................................................................................................... 82

WWAN I/O board .............................................................................................................................................................83

Removing the WWAN I/O board............................................................................................................................. 83

Installing the WWAN I/O board............................................................................................................................... 84

Palmrest assembly............................................................................................................................................................ 85

Removing the palmrest assembly............................................................................................................................85

Installing the palmrest assembly.............................................................................................................................. 86

Display bezel....................................................................................................................................................................... 88

Removing the display bezel.......................................................................................................................................88

Installing the display bezel.........................................................................................................................................89

Display panel.......................................................................................................................................................................90

Removing the display panel...................................................................................................................................... 90

Installing the display panel.........................................................................................................................................93

Camera.................................................................................................................................................................................96

Removing the camera ............................................................................................................................................... 96

Installing the camera ................................................................................................................................................. 96

Display cable....................................................................................................................................................................... 97

Removing the display cable ......................................................................................................................................97

Installing the display cable ........................................................................................................................................98

Display back-cover.......................................................................................................................................................... 100

Removing the display back-cover..........................................................................................................................100

Installing the display back-cover............................................................................................................................100

Chapter 3: Drivers and downloads.............................................................................................. 102

Chapter 4: BIOS setup............................................................................................................... 103

BIOS overview..................................................................................................................................................................103

Entering BIOS setup program.......................................................................................................................................103

Navigation keys................................................................................................................................................................ 103

One time boot menu....................................................................................................................................................... 104

System setup options..................................................................................................................................................... 104

Updating the BIOS........................................................................................................................................................... 114

Updating the BIOS in Windows............................................................................................................................... 114

Updating the BIOS in Linux and Ubuntu............................................................................................................... 114

Updating the BIOS using the USB drive in Windows......................................................................................... 114

Updating the BIOS from the F12 One-Time boot menu....................................................................................115

System and setup password..........................................................................................................................................115

Assigning a system setup password...................................................................................................................... 116

Deleting or changing an existing system setup password................................................................................ 116

Clearing CMOS settings..................................................................................................................................................117

Clearing BIOS (System Setup) and System passwords..........................................................................................117

Contents 5

Chapter 5: Troubleshooting........................................................................................................ 118

Handling swollen Lithium-ion batteries....................................................................................................................... 118

Dell SupportAssist Pre-boot System Performance Check diagnostics...............................................................118

Running the SupportAssist Pre-Boot System Performance Check............................................................... 119

Built-in self-test (BIST).................................................................................................................................................. 119

M-BIST.......................................................................................................................................................................... 119

LCD Power rail test (L-BIST)................................................................................................................................. 120

LCD Built-in Self Test (BIST)................................................................................................................................. 120

System-diagnostic lights................................................................................................................................................120

Recovering the operating system................................................................................................................................122

Real-Time Clock (RTC Reset)...................................................................................................................................... 122

Backup media and recovery options........................................................................................................................... 122

WiFi power cycle..............................................................................................................................................................123

Drain residual flea power (perform hard reset)........................................................................................................123

Chapter 6: Getting help and contacting Dell...............................................................................124

6 Contents

Working inside your computer

Safety instructions

Prerequisites

Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless

otherwise noted, each procedure included in this document assumes that the following conditions exist:

●You have read the safety information that shipped with your computer.

●A component can be replaced or, if purchased separately, installed by performing the removal procedure in reverse order.

About this task

WARNING: Before working inside your computer, read the safety information that shipped with your computer.

For additional safety best practices information, see the Regulatory Compliance Homepage

CAUTION: Many repairs may only be done by a certified service technician. You should only perform

troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or

telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by

your warranty. Read and follow the safety instructions that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically

touching an unpainted metal surface at the same time as touching a connector on the back of the computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a

card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by

its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some

cables have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking

tabs before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending

any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and

aligned.

NOTE: Disconnect all power sources before opening the computer cover or panels. After you finish working inside the

computer, replace all covers, panels, and screws before connecting to the power source.

CAUTION: Exercise caution when handling Lithium-ion batteries in laptops. Swollen batteries should not be used

and should be replaced and disposed properly.

NOTE: The color of your computer and certain components may appear differently than shown in this document.

Before working inside your computer

Steps

1. Save and close all open files and exit all open applications.

2. Shut down your computer. Click Start > Power > Shut down.

NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down

instructions.

3. Disconnect your computer and all attached devices from their electrical outlets.

4. Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.

Working inside your computer 7

5. Remove any media card and optical disc from your computer, if applicable.

6. After the computer is unplugged, press and hold the power button for 5 seconds to ground the system board.

CAUTION: Place the computer on a flat, soft, and clean surface to avoid scratches on the display.

7. Place the computer face down.

Entering Service Mode

Service Mode allows users to immediately cut off electricity from the computer and conduct repairs without disconnecting the

battery cable from the system board.

To enter Service Mode:

1. Shut down your computer and disconnect the AC adapter.

2. Hold <B> key on the keyboard and press the power button for 3 seconds or until the Dell logo appears on the screen.

3. Press any key to continue.

NOTE: If the power adapter has not been disconnected, a message prompting you to remove the AC adapter appears

on the screen. Remove the AC adapter and then press any key to continue the Service Mode procedure.

NOTE: The Service Mode procedure automatically skips the following step if the Owner Tag of the computer is not

set up in advance by the manufacturer.

4. When the ready-to-proceed message appears on the screen, press any key to proceed. The computer emits three short

beeps and shuts down immediately.

Once the computer shuts down, you may perform the replacement procedures without disconnecting the battery cable from

the system board.

Exiting Service Mode

Service Mode allows users to immediately cut off electricity from the computer and conduct repairs without disconnecting the

battery cable from the system board.

To exit Service Mode:

1. Connect the AC adapter to the power-adapter port on your computer.

2. Press the power button to turn on the computer. Your computer will automatically return to normal functioning mode.

Safety precautions

The safety precautions chapter details the primary steps to be taken before performing any disassembly instructions.

Observe the following safety precautions before you perform any installation or break/fix procedures involving disassembly or

reassembly:

●Turn off the system and all attached peripherals.

●Disconnect the system and all attached peripherals from AC power.

●Disconnect all network cables, telephone, and telecommunications lines from the system.

●Use an ESD field service kit when working inside any to avoid electrostatic discharge (ESD) damage.

●After removing any system component, carefully place the removed component on an anti-static mat.

●Wear shoes with non-conductive rubber soles to reduce the chance of getting electrocuted.

Standby power

Dell products with standby power must be unplugged before you open the case. Systems that incorporate standby power are

essentially powered while turned off. The internal power enables the system to be remotely turned on (wake on LAN) and

suspended into a sleep mode and has other advanced power management features.

Unplugging, pressing and holding the power button for 15 seconds should discharge residual power in the system board.

8Working inside your computer

Bonding

Bonding is a method for connecting two or more grounding conductors to the same electrical potential. This is done through

the use of a field service electrostatic discharge (ESD) kit. When connecting a bonding wire, ensure that it is connected to bare

metal and never to a painted or non-metal surface. The wrist strap should be secure and in full contact with your skin, and

ensure that you remove all jewelry such as watches, bracelets, or rings prior to bonding yourself and the equipment.

Electrostatic discharge—ESD protection

ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards,

processors, memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such

as intermittent problems or a shortened product life span. As the industry pushes for lower power requirements and increased

density, ESD protection is an increasing concern.

Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than

in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.

Two recognized types of ESD damage are catastrophic and intermittent failures.

●Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes

an immediate and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has

received a static shock and immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or

nonfunctional memory.

●Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of

intermittent failures means that most of the time when damage occurs, it is not immediately recognizable. The DIMM

receives a static shock, but the tracing is merely weakened and does not immediately produce outward symptoms related to

the damage. The weakened trace may take weeks or months to melt, and in the meantime may cause degradation of memory

integrity, intermittent memory errors, etc.

Perform the following steps to prevent ESD damage:

●Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do not

provide adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts

with increased sensitivity to ESD damage.

●Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.

●When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static

packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you

discharge static electricity from your body.

●Before transporting a static-sensitive component, place it in an anti-static container or packaging.

ESD field service kit

The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components:

anti-static mat, wrist strap, and bonding wire.

Components of an ESD field service kit

The components of an ESD field service kit are:

●Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an

anti-static mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal

on the system being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly

on the mat. ESD-sensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.

●Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist

and bare metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that

is temporarily placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD

mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never

use wireless wrist straps. Always be aware that the internal wires of a wrist strap are prone to damage from normal wear

and tear, and must be checked regularly with a wrist strap tester in order to avoid accidental ESD hardware damage. It is

recommended to test the wrist strap and bonding wire at least once per week.

●ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored

kit, it is a best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A

wrist strap tester is the best method for doing this test. If you do not have your own wrist strap tester, check with your

Working inside your computer 9

regional office to find out if they have one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is

strapped to your wrist and push the button to test. A green LED is lit if the test is successful; a red LED is lit and an alarm

sounds if the test fails.

●Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts

that are insulators and often highly charged.

●Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For

example, deploying the kit for a server environment is different than for a desktop or portable environment. Servers are

typically installed in a rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always

look for a large open flat work area that is free of clutter and large enough to deploy the ESD kit with additional space to

accommodate the type of system that is being repaired. The workspace should also be free of insulators that can cause an

ESD event. On the work area, insulators such as Styrofoam and other plastics should always be moved at least 12 inches or

30 centimeters away from sensitive parts before physically handling any hardware components

●ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded

bags are preferred. However, you should always return the damaged part using the same ESD bag and packaging that the

new part arrived in. The ESD bag should be folded over and taped shut and all the same foam packing material should be

used in the original box that the new part arrived in. ESD-sensitive devices should be removed from packaging only at an

ESD-protected work surface, and parts should never be placed on top of the ESD bag because only the inside of the bag is

shielded. Always place parts in your hand, on the ESD mat, in the system, or inside an anti-static bag.

●Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts

to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.

ESD protection summary

It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static

mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all

insulator parts while performing service and that they use anti-static bags for transporting sensitive components.

Transporting sensitive components

When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place

these parts in anti-static bags for safe transport.

After working inside your computer

About this task

NOTE: Leaving stray or loose screws inside your computer may severely damage your computer.

Steps

1. Replace all screws and ensure that no stray screws remain inside your computer.

2. Connect any external devices, peripherals, or cables you removed before working on your computer.

3. Replace any media cards, discs, or any other parts that you removed before working on your computer.

4. Connect your computer and all attached devices to their electrical outlets.

5. Turn on your computer.

10 Working inside your computer

Removing and installing components

NOTE: The images in this document may differ from your computer depending on the configuration you ordered.

Recommended tools

The procedures in this document may require the following tools:

●Phillips #0 screwdriver

●Plastic scribe

Screw List

The following table shows the screw list and the image of the screws.

Table 1. Screw list

Component Screw type Quantity Image

Base cover Captive screws 9

M.2 Solid-state drive bracket M2x3 1

M.2 Solid-state drive conversion bracket M2x3 1

M.2 Solid-state drive conversion plate M2x3 2

Hard disk-drive module M2X4.5 4

Hard disk-drive M3x3 4

WLAN card M2x3 1

WWAN card M2x3 1

System Fan M2x3 2

3-cell battery M2x3 3

4-cell battery M2x3 4

Removing and installing components 11

Table 1. Screw list (continued)

Component Screw type Quantity Image

Display hinges M2.5x6

M2.5x4

Hinge bracket M2.5x2.5

M2.5x3

Heatsink assembly Captive screws 7 (For systems

enabled with

discrete graphic

card)

4 (For systems

enabled with

integrated graphic

card)

Power adapter port M2x3 1

Ethernet port M2x5 2

I/O board M2x3 2

System board M2x2 2

Touchpad bracket M2x2.5 3

Touchpad module M2x2 4

WWAN I/O board M2x3 2

12 Removing and installing components

Major components of your system

Removing and installing components 13

1. Base cover

2. Battery

3. Memory module

4. WLAN card

5. Solid-state drive

6. Solid-state drive conversion bracket

7. WWAN card

8. Power adapter port

9. Coin-cell battery

10. Touchpad bracket

11. System board

12. Touchpad

13. Computer chassis/palmrest assembly

14. Display assembly

15. WWAN I/O board

16. I/O board

17. System fan

18. Heatsink assembly

19. Ethernet port

20. Power-button board

NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These

parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative for

purchase options.

MicroSD-card

Removing the microSD-card

Prerequisites

1. Follow the procedure in before working inside your computer.

About this task

The following image provides a visual representation of the microSD-card removal procedure.

14 Removing and installing components

Steps

1. Push the microSD-card to eject it from the slot.

2. Remove the microSD-card from the system.

Installing the MicroSD-card

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image provides a visual representation of the MicroSD-card installation procedure.

Steps

Insert the microSD-card into its slot until it clicks into place.

Next steps

1. Follow the procedure in after working inside your computer.

SIM card tray

Removing the SIM card tray

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

About this task

NOTE: The following steps are applicable only for 4G LTE enabled systems.

The following image provides a visual representation of the SIM card tray removal procedure.

Removing and installing components 15

Steps

1. Insert the SIM card removal pin into the release hole to release the SIM card tray.

2. Push the pin to disengage the lock, and eject the SIM card tray.

3. Slide the SIM card tray out of the slot on the computer.

4. Remove the MicroSIM-card from the SIM tray.

5. Slide the SIM card tray back into the slot on the computer.

Installing the SIM card tray

Prerequisites

If you are replacing a component, remove the necessary component before the installation procedure.

About this task

NOTE: The following steps are applicable only for 4G LTE enabled systems.

The following image provides a visual representation of the SIM card tray installation procedure.

16 Removing and installing components

Steps

1. Insert the SIM card removal pin into the release hole to remove the SIM card tray.

2. Push the pin to disengage the lock, and eject the SIM card tray.

3. Slide the SIM card tray out of the slot on the computer.

4. Align and place the MicroSIM-card in the dedicated slot on the SIM card tray.

5. Slide the SIM card tray back into the slot on the computer.

Next steps

1. Install the microSD-card.

2. Follow the procedure in after working inside your computer.

Base cover

Removing the base cover

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

Removing and installing components 17

About this task

The following images indicate the location of the base cover and provide a visual representation of the removal procedure.

18 Removing and installing components

Steps

1. Loosen the nine captive screws that secure the base cover to the palmrest assembly.

2. Using a plastic scribe, pry open the base cover starting from the recesses located in the U-shaped indents near the hinges at

the top edge of the base cover.

3. Carefully lift and remove the base cover from the chassis.

NOTE: Be careful of the latches while removing the base cover as the latches may break.

Installing the base cover

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following images indicate the location of the battery and provide a visual representation of the installation procedure.

Removing and installing components 19

Steps

1. Align and place the base cover on the palmrest assembly, and snap the base cover latches into place.

2. Tighten the nine captive screws to secure the base cover to the computer chassis.

Next steps

1. Exit the service mode

2. Install the SIM card tray for 4G LTE enabled systems.

3. Install the microSD-card.

4. Follow the procedure in after working inside your computer.

Battery cable

Lithium-ion battery precautions

CAUTION:

●Exercise caution when handling Lithium-ion batteries.

●Discharge the battery completely before removing it. Disconnect the AC power adapter from the system and

operate the computer solely on battery power—the battery is fully discharged when the computer no longer

turns on when the power button is pressed.

●Do not crush, drop, mutilate, or penetrate the battery with foreign objects.

●Do not expose the battery to high temperatures, or disassemble battery packs and cells.

●Do not apply pressure to the surface of the battery.

●Do not bend the battery.

20 Removing and installing components

●Do not use tools of any kind to pry on or against the battery.

●Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental

puncture or damage to the battery and other system components.

●If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing,

bending, or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical

support for assistance. See www.dell.com/contactdell.

●Always purchase genuine batteries from www.dell.com or authorized Dell partners and resellers.

●Swollen batteries should not be used and should be replaced and disposed properly. For guidelines on how to

handle and replace swollen Lithium-ion batteries, see Handling swollen Lithium-ion batteries.

Removing the battery cable

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Remove the base cover.

About this task

The following image indicates the location of the battery cable and provides a visual representation of the removal procedure.

Steps

1. Disconnect the battery cable from the connector on the system board.

2. Slide the metal above the connector on the battery to unlock.

3. Peel the adhesive tapes and unroute the battery cable from routing channel in the battery.

4. Disconnect the battery cable from the connector on the battery.

Removing and installing components 21

Installing the battery cable

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the battery cable and provides a visual representation of the installation procedure.

Steps

1. Connect the battery cable to the connector on the battery.

2. Slide the metal above the connector on the battery to lock.

3. Route the battery cable through the routing channel in the battery and adhere the adhesive tapes.

4. Connect the battery cable to the connector on the system board.

Next steps

1. Install the base cover.

2. Install the SIM card tray for 4G LTE enabled systems.

3. Install the microSD-card.

4. Follow the procedure in after working inside your computer.

Memory module

Removing the memory module

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

22 Removing and installing components

4. Enter the service mode.

5. Remove the base cover.

About this task

The following image indicates the location of the memory module and provides a visual representation of the removal procedure.

NOTE: The location of the memory module may vary depending on your system.

Steps

1. Lift the mylar to uncover the memory module.

2. Pry the retention clips securing the memory module slot until the memory module pops-up.

3. Remove the memory module from the memory module slot.

Installing the memory module

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

Removing and installing components 23

About this task

The following image indicates the location of the memory module and provides a visual representation of the installation

procedure.

NOTE: The location of the memory module may vary depending on your system.

Steps

1. Lift the mylar to find the memory module slot.

2. Align the notch on the memory module with the tab on the memory-module slot.

3. Slide the memory module firmly into the slot at an angle.

4. Press the memory module down until it clicks into place.

NOTE: If you do not hear the click, remove the memory module and reinstall it.

Next steps

1. Install the base cover.

2. Exit the service mode.

3. Install the SIM card tray for 4G LTE enabled systems.

4. Install the microSD-card.

24 Removing and installing components

5. Follow the procedure in after working inside your computer.

M.2 solid-state drive

Removing the M.2 2230 solid-state drive

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

About this task

The following image indicates the location of the solid-state drive and provides a visual representation of the removal procedure.

Steps

1. Remove the (M2x3) screw that secures the solid-state drive to the system board.

2. Slide and remove the solid-state drive from the solid-state drive slot on the system board.

Installing the M.2 2230 solid-state drive

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the solid-state drive and provides a visual representation of the installation

procedure.

Removing and installing components 25

Steps

1. Align the notch on the solid-state drive with the tab on the solid-state drive slot.

2. Slide the solid-state drive into the solid-state drive slot on the system board.

3. Replace the (M2x3) screw to secure the solid-state drive to the system board.

Next steps

1. Install the base cover.

2. Exit the service mode

3. Install the SIM card tray for 4G LTE enabled systems.

4. Install the microSD-card.

5. Follow the procedure in after working inside your computer.

Removing the M.2 2280 solid-state drive

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

About this task

The following image indicates the location of the solid-state drive and provides a visual representation of the removal procedure.

26 Removing and installing components

Steps

1. Remove the (M2x3) screw that secures the solid-state drive to the system board.

2. Slide and remove the solid-state drive from the solid-state drive slot on the system board.

Installing the M.2 2280 solid-state drive

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the solid-state drive and provides a visual representation of the installation

procedure.

Steps

1. Align the notch on the solid-state drive with the tab on the solid-state drive slot.

Removing and installing components 27

2. Slide the solid-state drive into the solid-state drive slot on the system board.

3. Replace the (M2x3) screw to secure the solid-state drive to the system board.

Next steps

1. Install the base cover.

2. Exit the service mode

3. Install the SIM card tray for 4G LTE enabled systems.

4. Install the microSD-card.

5. Follow the procedure in after working inside your computer.

M.2 solid-state drive conversion bracket

Replacing the M.2 solid-state drive conversion bracket

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

6. Remove the M.2 SSD.

About this task

The following image indicates the location of the M.2 solid-state drive conversion bracket and how it can be used to fit

solid-state drives of different length.

NOTE: The following image is from systems shipped with discrete graphic card. The system board has a different

configuration for systems shipped with integrated graphic card.

28 Removing and installing components

Steps

1. Remove the (M2x3) screw that secures the solid-state drive conversion bracket to the solid-state drive conversion plate.

2. Depending on the type of solid-state drive (M.2 2230/ M.2 2280), turn, align and place the solid-state drive conversion

bracket into the slot.

3. Install the (M2x3) screw to secure the solid-state drive conversion bracket to the solid-state drive conversion plate.

M.2 solid-state drive conversion plate

Removing the M.2 solid-state drive conversion plate

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

6. Remove the M.2 SSD.

Removing and installing components 29

About this task

The following image indicates the location of the M.2 solid-state drive conversion plate and provides a visual representation of

the removal procedure.

NOTE: The following image is from systems shipped with discrete graphic card. The system board has a different

configuration for systems shipped with integrated graphic card.

Steps

1. Remove the two (M2x3) screws that secures the solid-state drive conversion plate to the system board.

2. Lift and remove the solid-state drive conversion plate from the solid-state drive slot on the system board.

Installing the M.2 solid-state drive conversion plate

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the M.2 solid-state drive conversion plate and provides a visual representation of

the installation procedure.

NOTE: The following image is from systems shipped with discrete graphic card. The system board has a different

configuration for systems shipped with integrated graphic card.

30 Removing and installing components

Steps

1. Align and place the solid-state drive conversion plate on the system board.

2. Install the two (M2x3) screws to secure the solid-state drive conversion plate to the system board.

Next steps

1. Install the M.2 SSD.

2. Install the base cover.

3. Exit the service mode

4. Install the SIM card tray for 4G LTE enabled systems.

5. Install the microSD-card.

6. Follow the procedure in after working inside your computer.

Hard-disk drive assembly

Removing the hard-disk drive assembly

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

About this task

The following image indicates the location of the hard-disk drive assembly and provides a visual representation of the removal

procedure.

NOTE: The following steps are applicable only for systems shipped with 3-cell battery.

Removing and installing components 31

Steps

1. Lift and disconnect the hard-disk drive cable from the connector on the system board.

2. Loosen the four (M2X4.5) screws that secure the hard-disk drive assembly to the palmrest assembly.

3. Lift and remove the hard-disk drive assembly from the slot on the palmrest assembly.

Removing the hard-disk drive bracket

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

6. Remove the hard-disk drive.

About this task

The following image indicates the location of the hard-disk drive bracket and provides a visual representation of the removal

procedure.

32 Removing and installing components

Steps

1. Disconnect the hard-disk drive cable from the connector on the hard-disk drive bracket.

2. Remove the four (M3x3) screws that secure the hard-disk drive to the hard-disk drive bracket.

3. Flip the hard-disk drive bracket, lift the silver foil, and remove the hard-disk drive from the hard-disk drive bracket.

Installing the hard-disk drive bracket

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the hard-disk drive bracket and provides a visual representation of the installation

procedure.

Removing and installing components 33

Steps

1. Lift the silver foil, align and place the hard-disk drive in the hard-disk drive bracket.

2. Install the four (M3x3) screws to secure the hard-disk drive to the hard-disk drive bracket.

3. Connect the hard-disk drive cable to the connector on the hard-disk drive bracket.

Next steps

1. Install the hard-disk drive.

2. Install the base cover.

3. Exit the service mode

4. Install the SIM card tray for 4G LTE enabled systems.

5. Install the microSD-card.

6. Follow the procedure in after working inside your computer.

Installing the hard-disk drive assembly

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the hard-disk drive assembly and provides a visual representation of the installation

procedure.

NOTE: The following steps are applicable only for systems shipped with 3-cell battery.

NOTE: Systems that are shipped with 3-cell battery contain a rubber bumper that must be removed manually before

installing the hard-disk drive assembly.

34 Removing and installing components

Steps

1. Align and place the hard-disk drive assembly in the slot on the palmrest assembly.

2. Tighten the four (M2X4.5) screws to secure the hard-disk drive assembly to the palmrest assembly.

3. Connect the hard-disk drive cable to the connector on the system board.

Next steps

1. Install the base cover.

2. Exit the service mode

3. Install the SIM card tray for 4G LTE enabled systems.

4. Install the microSD-card.

5. Follow the procedure in after working inside your computer.

WLAN card

Removing the WLAN card

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

About this task

The following image indicates the location of the WLAN card and provides a visual representation of the removal procedure.

Removing and installing components 35

Steps

1. Remove the screw (M2x3) that secures WLAN card bracket to the WLAN card on the system board.

2. Lift and remove the WLAN card bracket from the WLAN card that secures the two antenna cables.

3. Disconnect the antenna cables from the connectors on the WLAN card.

4. Disconnect and remove the WLAN card from the WLAN card slot.

Installing the WLAN card

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the WLAN card and provides a visual representation of the installation procedure.

36 Removing and installing components

Steps

1. Connect the two antenna cables to the connectors on the WLAN card.

NOTE: The antenna cable connectors are fragile and utmost care should be taken while replacing them.

Table 2. Antenna cable guide

Cable color Connector

White cable (Main) White triangle (△) on the WLAN module of the system board

Black cable (Aux) Solid triangle (▲) on the WLAN module of the system board

2. Align the notch on the WLAN card with the tab on the WLAN card slot.

3. Slide the WLAN card at an angle into the WLAN card slot.

4. Align and place the WLAN card bracket on the WLAN card.

5. Install the screw (M2x3) to secure the WLAN card bracket on the WLAN card to the system board.

Next steps

1. Install the base cover.

2. Exit the service mode

Removing and installing components 37

3. Install the SIM card tray for 4G LTE enabled systems.

4. Install the microSD-card.

5. Follow the procedure in after working inside your computer.

WWAN card

Removing the WWAN card

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

About this task

The following image indicates the location of the WWAN card and provides a visual representation of the removal procedure.

NOTE: The following steps are applicable only for 4G LTE enabled systems.

38 Removing and installing components

Steps

1. Open the mylar sheet that covers the WWAN card.

2. Remove the screw (M2x3) that secures WWAN card bracket to the WWAN card on the system board.

3. Lift and remove the WWAN card bracket from the WWAN card that secures the two antenna cables.

4. Disconnect the antenna cables from the connectors on the WWAN card.

5. Disconnect and remove the WWAN card from the WWAN card slot.

Installing the WWAN card

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the WWAN card and provides a visual representation of the installation procedure.

NOTE: The following steps are applicable only for 4G LTE enabled systems.

Steps

1. Connect the two antenna cables to the connectors on the WWAN card.

NOTE: The antenna cable connectors are fragile and utmost care should be taken while replacing them.

Removing and installing components 39

Table 3. Antenna cable guide

Cable color Connector

White cable (Main) White triangle (△) on the WWAN module of the system

board

Black cable (Aux) Solid triangle (▲) on the WWAN module of the system

board

2. Align the notch on the WWAN card with the tab on the WWAN card slot.

3. Slide the WWAN card at an angle into the WWAN card slot.

4. Align and place the WWAN card bracket on the WWAN card.

5. Install the screw (M2x3) to secure the WWAN card bracket on the WWAN card to the system board.

6. Close the mylar sheet to cover the WWAN card.

Next steps

1. Install the base cover.

2. Exit the service mode

3. Install the SIM card tray for 4G LTE enabled systems.

4. Install the microSD-card.

5. Follow the procedure in after working inside your computer.

System fan

Removing the system fan

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for systems enabled with 4G LTE.

4. Enter the service mode.

5. Remove the base cover.

About this task

The following image indicates the location of the system fan and provides a visual representation of the removal procedure.

40 Removing and installing components

Steps

1. Disconnect the system fan cable from the connector on the system board.

2. Remove the two (M2x3) screws that secure the system fan to the palmrest assembly.

3. Lift and remove the system fan from the palmrest assembly.

Installing the system fan

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the system fan and provides a visual representation of the installation procedure.

Removing and installing components 41

Steps

1. Align and place the system fan into the slot on the palmrest assembly.

2. Install the two (M2x3) screws to secure the system fan to the palmrest assembly.

3. Connect the system fan cable to the connector on the system board.

Next steps

1. Install the base cover.

2. Exit the service mode

3. Install the SIM card tray for systems enabled with 4G LTE.

4. Install the microSD-card.

5. Follow the procedure in after working inside your computer.

Battery

Removing the 3-cell battery

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Remove the base cover.

About this task

The following image indicates the location of the battery and provides a visual representation of the removal procedure.

42 Removing and installing components

Steps

1. Disconnect the battery cable from the connector on the system board.

2. Remove the three (M2X3) screws that secure the battery in place.

3. Lift and remove the battery from the palmrest assembly.

4. Slide the metal above the connector on the battery to unlock.

5. Peel the adhesive tapes and unroute the battery cable from routing channel in the battery.

6. Disconnect the battery cable from the connector on the battery.

Installing the 3-cell battery

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the battery and provides a visual representation of the installation procedure.

Removing and installing components 43

Steps

1. Connect the battery cable to the connector on the battery.

2. Slide the metal above the connector on the battery to lock.

3. Route the battery cable through the routing channel in the battery and adhere the adhesive tapes.

4. Align and place the battery in the slot on the palmrest assembly.

5. Install the three (M2X3) screws to secure the battery in place.

6. Connect the battery cable to the connector on the system board.

Next steps

1. Install the base cover.

2. Install the SIM card tray for 4G LTE enabled systems.

3. Install the microSD-card.

4. Follow the procedure in after working inside your computer.

44 Removing and installing components

Removing the 4-cell battery

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Remove the base cover.

About this task

The following image indicates the location of the battery and provides a visual representation of the removal procedure.

Steps

1. Disconnect the battery cable from the connector on the system board.

2. Remove the four (M2X3) screws that secure the battery in place.

3. Lift and remove the battery from the palmrest assembly.

4. Slide the metal above the connector on the battery to unlock.

5. Peel the adhesive tapes and unroute the battery cable from routing channel in the battery.

Removing and installing components 45

6. Disconnect the battery cable from the connector on the battery.

Installing the 4-cell battery

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the battery and provides a visual representation of the installation procedure.

Steps

1. Connect the battery cable to the connector on the battery.

2. Slide the metal above the connector on the battery to lock.

3. Route the battery cable through the routing channel in the battery and adhere the adhesive tapes.

4. Align and place the battery in the slot on the palmrest assembly.

5. Install the four (M2X3) screws to secure the battery in place.

46 Removing and installing components

6. Connect the battery cable to the connector on the system board.

Next steps

1. Install the base cover.

2. Install the SIM card tray for 4G LTE enabled systems.

3. Install the microSD-card.

4. Follow the procedure in after working inside your computer.

I/O cable

Removing the I/O cable

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the SIM card tray for 4G LTE enabled systems.

3. Enter the service mode.

4. Remove the base cover.

About this task

The following image indicates the location of the I/O cable and provides a visual representation of the removal procedure.

Steps

1. Peel the adhesive tape, open the latch and disconnect the I/O cable from the connector on the system board.

2. Peel the adhesive tape and unroute the I/O cable from the routing guides in the palmrest assembly.

3. Peel the adhesive tape, open the latch and disconnect the I/O cable from the connector on the I/O board.

4. Lift and remove the I/O cable from the palmrest assembly.

Removing and installing components 47

Installing the I/O cable

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the I/O cable and provides a visual representation of the installation procedure.

Steps

1. Route the I/O cable through the routing guides and adhere the adhesive tape to secure the I/O cable in place.

2. Connect the I/O cable to the connector on the system board, adhere the adhesive tape, and close the latch.

3. Connect the I/O cable to the connector on the I/O board, adhere the adhesive tape, and close the latch.

Next steps

1. Install the base cover.

2. Exit the service mode

3. Install the microSD-card.

4. Install the SIM card tray for 4G LTE enabled systems.

5. Follow the procedure in after working inside your computer.

Display assembly

Removing the display assembly

Prerequisites

1. Follow the procedure in before working inside your computer.

48 Removing and installing components

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

6. Remove the WLAN card.

7. Remove the WWAN card for systems enabled with 4G LTE.

8. Remove the I/O cable.

About this task

The following images indicate the location of the display assembly and provide a visual representation of the removal procedure.

Removing and installing components 49

Steps

1. Unroute the display cable from the routing guides in the palmrest assembly.

2. Peel the adhesive tape that secures the display cable in place.

3. Open the latch and disconnect the display cable from the connector on the system board.

4. Remove the (M2.5x4) and six (M2.5x6) screws that secure the display hinges to the system.

5. Lift the left and right hinges in upward direction away from the palmrest assembly.

6. Lift the palmrest assembly off the display assembly.

50 Removing and installing components

Installing the display assembly

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following images indicate the location of the display assembly and provide a visual representation of the installation

procedure.

Removing and installing components 51

Steps

1. Align and place the system chassis under the hinges of the display assembly.

2. Press the left and right hinges in downward direction toward the palmrest assembly.

3. Install the (M2.5x4) and six (M2.5x6) screws to secure the display hinges to the palmrest assembly.

4. Connect the display cable to the connector on the system board and close the latch.

5. Route the display cable through the routing guides in the palmrest assembly.

6. Affix the adhesive tape to secures the display cable in place.

Next steps

1. Install the I/O cable.

2. Install the WWAN card for systems enabled with 4G LTE.

3. Install the WLAN card.

4. Install the base cover.

5. Exit the service mode

6. Install the SIM card tray for 4G LTE enabled systems.

7. Install the microSD-card.

8. Follow the procedure in after working inside your computer.

52 Removing and installing components

Heatsink assembly

Removing the heatsink assembly - for computers with discrete

graphics card

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for systems enabled with 4G LTE.

4. Enter the service mode.

5. Remove the base cover.

About this task

The following images indicate the location of the heatsink assembly and provide a visual representation of the removal

procedure.

Steps

1. Loosen the seven captive screws (in reverse order, 7>6>5>4->3->2->1) that secure the heatsink assembly to the system

board.

2. Lift and remove the heatsink assembly from the system board.

Removing and installing components 53

Installing the heatsink assembly - for computers with discrete

graphics card

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the heatsink assembly and provides a visual representation of the installation

procedure.

Steps

1. Align and place the heatsink assembly into the slot on the system board.

2. Tighten the seven captive screws (in order, 1>2>3>4->5->6->7) to secure the heatsink assembly to the system board.

Next steps

1. Install the base cover.

2. Exit the service mode

3. Install the SIM card tray for systems enabled with 4G LTE.

4. Install the microSD-card.

5. Follow the procedure in after working inside your computer.

54 Removing and installing components

Removing the heatsink assembly - for computers with integrated

graphics card

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for systems enabled with 4G LTE.

4. Enter the service mode.

5. Remove the base cover.

About this task

The following images indicate the location of the heatsink assembly and provide a visual representation of the removal

procedure.

Steps

1. Loosen the four captive screws (in reverse order, 4->3->2->1) that secure the heatsink assembly to the system board.

2. Lift and remove the heatsink assembly from the system board.

Installing the heatsink assembly - for computers with integrated

graphics card

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

Removing and installing components 55

About this task

The following image indicates the location of the heatsink assembly and provides a visual representation of the installation

procedure.

Steps

1. Align and place the heatsink assembly into the slot on the system board.

2. Tighten the four captive screws (in order, 1>2>3>4) to secure the heatsink assembly to the system board.

Next steps

1. Install the base cover.

2. Exit the service mode

3. Install the SIM card tray for systems enabled with 4G LTE.

4. Install the microSD-card.

5. Follow the procedure in after working inside your computer.

Power adapter port

Removing the power adapter port

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

56 Removing and installing components

About this task

The following image indicates the location of the power adapter port and provides a visual representation of the removal

procedure.

Steps

1. Remove the (M2.5x4) and two (M2.5x6) screws that secure the display hinges to the system.

2. Disconnect the power adapter port from the connector on the system board.

3. Remove the (M2x3) screw that secures the power adapter port to the palmrest assembly.

4. Lift and remove the power adapter port from the palmrest assembly.

Installing the power adapter port

About this task

The following image indicates the location of the power adapter port and provides a visual representation of the removal

procedure.

Removing and installing components 57

Steps

1. Align and place the power adapter port on the palmrest assembly.

2. Install the (M2x3) screw to secure the power adapter port to the palmrest assembly.

3. Connect the power adapter port to the connector on the system board.

4. Install the (M2.5x4) and two (M2.5x6) screws to secure the display hinges to the system.

Next steps

1. Install the base cover.

2. Exit the service mode

3. Install the SIM card tray for 4G LTE enabled systems.

4. Install the microSD-card.

5. Follow the procedure in after working inside your computer.

Coin-cell battery

Removing the coin-cell battery

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

6. Remove the WWAN card for 4G LTE enabled systems.

7. Remove the hard-disk drive for systems shipped with hard-disk drive.

About this task

NOTE: If the CMOS battery is disconnected from system board for service, there will be a delay during system boot as the

system undergoes RTC battery reset.

58 Removing and installing components

The following image indicates the location of the coin-cell battery and provides a visual representation of the removal procedure.

Steps

1. Open the mylar sheet that covers the coin-cell battery cable.

2. Disconnect the coin-cell battery cable from the connector on the I/O board.

3. Lift and remove the coin-cell battery from the palmrest assembly.

Installing the coin-cell battery

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

NOTE: If the CMOS battery is disconnected from system board for service, there will be a delay during system boot as the

system undergoes RTC battery reset.

The following image indicates the location of the coin-cell battery and provides a visual representation of the installation

procedure.

Removing and installing components 59

Steps

1. Align and place the coin-cell battery on the palmrest assembly.

2. Connect the coin-cell battery cable to the connector on the I/O board.

3. Close the mylar sheet to cover the coin-cell battery cable.

Next steps

1. Install the hard-disk drive for systems shipped with hard-disk drive.

2. Install the WWAN card for 4G LTE enabled systems.

3. Install the base cover.

4. Exit the service mode

5. Install the SIM card tray for 4G LTE enabled systems.

6. Install the microSD-card.

7. Follow the procedure in after working inside your computer.

USB cable

Removing the USB cable

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Remove the base cover.

5. Remove the battery.

6. Remove the hard-disk drive.

60 Removing and installing components

7. Remove the WWAN card for 4G LTE enabled systems.

About this task

The following image indicates the location of the USB cable and provides a visual representation of the removal procedure.

Steps

1. Open the latch and disconnect the USB cable from the connector on the system board.

2. Carefully peel the USB cable from the palmrest assembly.

3. Open the latch and disconnect the USB cable from the connector on the I/O board.

4. Lift and remove the USB cable from the palmrest assembly.

Installing the USB cable

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the USB cable and provides a visual representation of the installation procedure.

Removing and installing components 61

Steps

1. Connect the USB cable to the connector on the system board and close the latch.

2. Align and adhere the USB cable on the palmrest assembly.

3. Connect the USB cable to the connector on the I/O board and close the latch.

Next steps

1. Install the WWAN card for 4G LTE enabled systems.

2. Install the hard-disk drive.

3. Install the battery.

4. Install the base cover.

5. Install the SIM card tray for 4G LTE enabled systems.

6. Install the microSD-card.

7. Follow the procedure in after working inside your computer.

Ethernet port

Removing the ethernet port

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

About this task

The following image indicates the location of the ethernet port and provides a visual representation of the removal procedure.

62 Removing and installing components

Steps

1. Remove the four (M2.5x6) screws to secure the hinge bracket on the palmrest assembly.

2. Lift the hinge in upward direction away from the palmrest assembly.

3. Remove the two (M2x5) screws that secure the ethernet on the I/O board.

4. Lift and remove the ethernet from the I/O board.

Installing the ethernet port

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the ethernet port and provides a visual representation of the installation procedure.

Removing and installing components 63

Steps

1. Align and place the ethernet on the I/O board.

2. Install the two (M2x5) screws to secure the ethernet on the I/O board.

3. Press the hinge in downward direction toward the palmrest assembly.

4. Install the four (M2.5x6) screws to secure the hinge bracket on the palmrest assembly.

Next steps

1. Install the base cover.

2. Exit the service mode

3. Install the SIM card tray for 4G LTE enabled systems.

4. Install the microSD-card.

5. Follow the procedure in after working inside your computer.

I/O board

Removing the I/O board

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

6. Remove the ethernet port.

About this task

NOTE:

The following image indicates the location of the I/O board and provides a visual representation of the removal procedure.

64 Removing and installing components

Steps

1. For systems shipped with power button, peel the adhesive, open the latch and disconnect the power button cable from the

connector on the I/O board.

2. Open the latch and disconnect the I/O cable from the connector on the system board.

3. Disconnect the USB cable and coin-cell cable from the connectors on the system board.

4. Remove the two (M2x3) screws that secure the I/O board on the palmrest assembly.

5. Lift and remove the I/O board from the palmrest assembly.

Installing the I/O board

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

NOTE:

The following image indicates the location of the I/O board and provides a visual representation of the installation procedure.

Removing and installing components 65

Steps

1. Align and place the I/O board into its slot on the palmrest assembly.

2. Install the two (M2x3) screws that secure the I/O board on the palmrest assembly.

3. Connect the USB cable and coin-cell cable to the connectors on the system board.

4. Connect the I/O cable to the connector on the system board and close the latch.

5. For systems shipped with power button, connect the power button cable to the connector on the I/O board, close the latch

and affix the adhesive tape.

Next steps

1. Install the ethernet port.

2. Install the base cover.

3. Exit the service mode

4. Install the SIM card tray for 4G LTE enabled systems.

5. Install the microSD-card.

6. Follow the procedure in after working inside your computer.

Power button

Removing the power button without fingerprint reader

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

6. Remove the I/O board.

66 Removing and installing components

7. Remove the ethernet port.

About this task

The following image indicates the location of the power button without fingerprint reader and provides a visual representation of

the removal procedure.

Steps

Lift the power button off the palmrest assembly.

Installing the power button without fingerprint reader

About this task

The following image indicates the location of the power button without fingerprint reader and provides a visual representation of

the removal procedure.

Removing and installing components 67

Steps

Align and place the power button into the slot on the palmrest assembly.

Next steps

1. Install the ethernet port.

2. Install the I/O board.

3. Install the base cover.

4. Exit the service mode

5. Install the SIM card tray for 4G LTE enabled systems.

6. Install the microSD-card.

7. Follow the procedure in after working inside your computer.

Removing the power button with fingerprint reader

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

6. Remove the I/O board.

7. Remove the ethernet port.

About this task

The following image indicates the location of the power button with fingerprint reader and provides a visual representation of

the removal procedure.

NOTE:

Steps

1. Peel the power button cable with adhesive backing from the palmrest assembly.

2. Lift the power button with fingerprint reader off the palmrest assembly.

68 Removing and installing components

Installing the power button with fingerprint reader

About this task

The following image indicates the location of the power button with fingerprint reader and provides a visual representation of

the removal procedure.

NOTE:

Steps

1. Affix the power button cable with adhesive backing.

2. Align and place the power button with fingerprint reader into the slot on the palmrest assembly.

Next steps

1. Install the ethernet port.

2. Install the I/O board.

3. Install the base cover.

4. Exit the service mode

5. Install the SIM card tray for 4G LTE enabled systems.

6. Install the microSD-card.

7. Follow the procedure in after working inside your computer.

System board

Removing the system board - for computers with discrete graphics

card

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Remove the base cover.

5. Remove the battery.

Removing and installing components 69

6. Remove the memory module.

7. Remove the M.2 SSD.

8. Remove the hard-disk drive for systems shipped with hard-disk drive.

9. Remove the WLAN card.

10. Remove the heatsink assembly.

About this task

Figure 1. System board connectors

1. System fan cable connector 2. Display cable connector

3. Power adapter port connector 4. Memory module connector

5. Keyboard backlit LED cable connector 6. Keyboard cable connector

7. Touchpad cable connector 8. Battery cable connector

9. WLAN card connector 10. Hard-disk drive cable connector

11. USB cable connector 12. Speaker cable connector

13. I/O cable connector 14. M.2 SSD connector

70 Removing and installing components

The following images indicate the location of the system board and provide a visual representation of the removal procedure.

Removing and installing components 71

Steps

1. Remove the two (M2.5x6) and the (M2.5x4) screws that secure the hinge to the palmrest assembly.

2. Lift the hinge in upward direction away from the palmrest assembly.

3. For 4G LTE enabled systems, peel the WWAN I/O board cable from the palmrest assembly.

4. Disconnect the speaker cable, power adapter port cable, hard-disk drive cable, and system fan cable from the connector on

the system board.

5. Open the latch and disconnect the touchpad cable, keyboard cable, and USB cable from the connector on the system board.

6. Peel the adhesive, open the latch, and disconnect the display cable and I/O cable from the connector on the system board.

7. Remove the two (M2x5) screws that secure the type-c bracket in place.

8. Lift and remove the type-c bracket from the system board.

9. Remove the two (M2x2) screws that secure the system board in place.

10. Lift and remove the system board from the palmrest assembly.

Installing the system board - for computers with discrete graphics

card

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

Figure 2. System board connectors

1. System fan cable connector 2. Display cable connector

3. Power adapter port connector 4. Memory module connector

5. Keyboard backlit LED cable connector 6. Keyboard cable connector

7. Touchpad cable connector 8. Battery cable connector

9. WLAN card connector 10. Hard-disk drive cable connector

11. USB cable connector 12. Speaker cable connector

13. I/O cable connector 14. M.2 SSD connector

72 Removing and installing components

The following images indicate the location of the system board and provide a visual representation of the installation procedure.

Removing and installing components 73

Steps

1. Align and place the system board into the slot on the palmrest assembly.

2. Install the two (M2x2) screws to secure the system board in place.

3. Align and place the type-c bracket on the system board.

4. Install the two (M2x5) screws to secure the type-c bracket in place.

5. Connect the display cable and I/O cable to the connector on the system board, close the latches and affix the adhesive

tapes.

6. Connect the touchpad cable, keyboard cable, and USB cable to the connector on the system board and close the latches.

7. Connect the speaker cable, power adapter port cable, hard-disk drive cable, and system fan cable to the connector on the

system board.

8. For 4G LTE enabled systems, affix the WWAN I/O board cable on the palmrest assembly.

9. Press the hinge in downward direction toward the palmrest assembly.

10. Install the two (M2.5x6) and the (M2.5x4) screws to secure the hinge to the palmrest assembly.

Next steps

1. Install the heatsink assembly.

2. Install the WLAN card.

3. Install the hard-disk drive for systems shipped with hard-disk drive.

4. Install the M.2 SSD.

5. Install the memory module.

6. Install the battery.

7. Install the base cover.

8. Install the SIM card tray for 4G LTE enabled systems.

9. Install the microSD-card.

10. Follow the procedure in after working inside your computer.

Removing the system board - for computers with integrated

graphics card

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Remove the base cover.

5. Remove the battery.

6. Remove the memory module.

7. Remove the M.2 SSD.

8. Remove the hard-disk drive for systems shipped with hard-disk drive.

9. Remove the WLAN card.

10. Remove the heatsink assembly.

74 Removing and installing components

About this task

Figure 3. System board connectors

1. System fan cable connector 2. Display cable connector

3. Power adapter port connector 4. Memory module connector

5. Keyboard backlit LED cable connector 6. Keyboard cable connector

7. Touchpad cable connector 8. Battery cable connector

9. WLAN card connector 10. Hard-disk drive cable connector

11. USB cable connector 12. Speaker cable connector

13. I/O cable connector 14. M.2 SSD connector

Removing and installing components 75

The following images indicate the location of the system board and provide a visual representation of the removal procedure.

76 Removing and installing components

Steps

1. Remove the two (M2.5x6) and the (M2.5x4) screws that secure the hinge to the palmrest assembly.

2. Lift the hinge in upward direction away from the palmrest assembly.

3. For 4G LTE enabled systems, peel the WWAN I/O board cable from the palmrest assembly.

4. Disconnect the speaker cable, power adapter port cable, hard-disk drive cable, and system fan cable from the connector on

the system board.

5. Open the latch and disconnect the touchpad cable, keyboard cable, and USB cable from the connector on the system board.

6. Peel the adhesive, open the latch, and disconnect the display cable and I/O cable from the connector on the system board.

7. Remove the two (M2x5) screws that secure the type-c bracket in place.

8. Lift and remove the type-c bracket from the system board.

9. Remove the two (M2x2) screws that secure the system board in place.

10. Lift and remove the system board from the palmrest assembly.

Installing the system board - for computers with integrated

graphics card

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

Figure 4. System board connectors

1. System fan cable connector 2. Display cable connector

3. Power adapter port connector 4. Memory module connector

5. Keyboard backlit LED cable connector 6. Keyboard cable connector

7. Touchpad cable connector 8. Battery cable connector

9. WLAN card connector 10. Hard-disk drive cable connector

11. USB cable connector 12. Speaker cable connector

13. I/O cable connector 14. M.2 SSD connector

Removing and installing components 77

The following images indicate the location of the system board and provide a visual representation of the installation procedure.

78 Removing and installing components

Steps

1. Align and place the system board into the slot on the palmrest assembly.

2. Install the two (M2x2) screws to secure the system board in place.

3. Align and place the type-c bracket on the system board.

4. Install the two (M2x5) screws to secure the type-c bracket in place.

5. Connect the display cable and I/O cable to the connector on the system board, close the latches and affix the adhesive

tapes.

6. Connect the touchpad cable, keyboard cable, and USB cable to the connector on the system board and close the latches.

7. Connect the speaker cable, power adapter port cable, hard-disk drive cable, and system fan cable to the connector on the

system board.

8. For 4G LTE enabled systems, affix the WWAN I/O board cable on the palmrest assembly.

9. Press the hinge in downward direction toward the palmrest assembly.

10. Install the two (M2.5x6) and the (M2.5x4) screws to secure the hinge to the palmrest assembly.

Next steps

1. Install the heatsink assembly.

2. Install the WLAN card.

3. Install the hard-disk drive for systems shipped with hard-disk drive.

4. Install the M.2 SSD.

5. Install the memory module.

6. Install the battery.

7. Install the base cover.

8. Install the SIM card tray for 4G LTE enabled systems.

9. Install the microSD-card.

10. Follow the procedure in after working inside your computer.

Speakers

Removing the speaker

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Remove the base cover.

5. Remove the battery.

About this task

The following image indicates the location of the speakers and provides a visual representation of the removal procedure.

Removing and installing components 79

Steps

1. Disconnect the speaker cable from the connector on the system board.

2. Unroute the speaker cable from the routing guides in the palmrest assembly.

3. Peel the adhesive tapes, lift and remove the speakers off the palmrest assembly.

Installing the speaker

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the speakers and provides a visual representation of the installation procedure.

80 Removing and installing components

Steps

1. Align and place the speakers into the slot on the palmrest assembly.

2. Route the speaker cable through the routing guides in the palmrest assembly.

3. Connect the speaker cable to the connector on the system board.

4. Affix the adhesive tapes to secure the speakers in place.

Next steps

1. Install the battery.

2. Install the base cover.

3. Install the SIM card tray for 4G LTE enabled systems.

4. Install the microSD-card.

5. Follow the procedure in after working inside your computer.

Touchpad

Removing the touchpad

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Remove the base cover.

5. Remove the battery.

6. Remove the speakers.

About this task

The following image indicates the location of the touchpad and provides a visual representation of the removal procedure.

Removing and installing components 81

Steps

1. Open the latch and disconnect the touchpad cable from the connector on the system board.

2. Peel the adhesive tapes that secure the touchpad module in place.

3. Remove the three (M2x2.5) screws that secure the touchpad bracket to the touchpad module.

4. Lift and remove the touchpad bracket from the touchpad module.

5. Remove the four (M2x2) screws that secure the touchpad module to the palmrest assembly.

6. Lift and remove the touchpad module from the palmrest assembly.

Installing the touchpad

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the touchpad and provides a visual representation of the installation procedure.

82 Removing and installing components

Steps

1. Align and place the touchpad module into the slot on the palmrest assembly.

2. Install the four (M2x2) screws to secure the touchpad module to the palmrest assembly.

3. Align and place the touchpad bracket on the touchpad module.

4. Install the three (M2x2.5) screws to secure the touchpad bracket to the touchpad module.

5. Affix the adhesive tapes to secure the touchpad module in place.

6. Connect the touchpad cable to the connector on the system board and close the latch.

Next steps

1. Install the speakers.

2. Install the battery.

3. Install the base cover.

4. Install the SIM card tray for 4G LTE enabled systems.

5. Install the microSD-card.

6. Follow the procedure in after working inside your computer.

WWAN I/O board

Removing the WWAN I/O board

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Remove the base cover.

5. Remove the battery cable.

Removing and installing components 83

About this task

The following image indicates the location of the WWAN I/O board and provides a visual representation of the removal

procedure.

NOTE: The following steps are applicable only for 4G LTE enabled systems.

Steps

1. Remove the two (M2x3) screws that secure the WWAN I/O board to the palmrest assembly.

2. Open the latch and disconnect the WWAN cable from the connector on the WWAN I/O board.

3. Lift and remove the WWAN I/O board from the palmrest assembly.

Installing the WWAN I/O board

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the WWAN I/O board and provides a visual representation of the installation

procedure.

NOTE: The following steps are applicable only for 4G LTE enabled systems.

84 Removing and installing components

Steps

1. Connect the WWAN cable to the connector on the WWAN I/O board and close the latch.

2. Align and place the WWAN I/O board into its slot on the palmrest assembly.

3. Install the two (M2x3) screws to secure the WWAN I/O board to the palmrest assembly.

Next steps

1. Install the battery cable

2. Install the base cover.

3. Install the SIM card tray for 4G LTE enabled systems.

4. Install the microSD card.

5. Follow the procedure in After working on your computer.

Palmrest assembly

Removing the palmrest assembly

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Remove the base cover.

5. Remove the battery.

6. Remove the memory module.

7. Remove the M.2 SSD.

8. Remove the M.2 SSD conversion bracket.

9. Remove the M.2 SSD conversion plate.

10. Remove the hard-disk drive.

11. Remove the WLAN card.

12. Remove the WWAN card for systems enabled with 4G LTE.

13. Remove the I/O board cable.

Removing and installing components 85

14. Remove the display assembly.

15. Remove the system fan.

16. Remove the heatsink assembly.

17. Remove the power adapter port.

18. Remove the I/O board.

19. Remove the coin-cell battery.

20. Remove the USB cable.

21. Remove the WWAN I/O board for systems enabled with 4G LTE.

22. Remove the system board.

NOTE: The system board can be removed along with the heat sink.

About this task

The following images indicate the location of the palmrest assembly.

Steps

After performing the preceding steps, you are left with the palmrest assembly.

Installing the palmrest assembly

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the palmrest assembly.

86 Removing and installing components

Steps

After performing the succeeding steps, you are left with the palmrest assembly.

Next steps

1. Install the system board.

2. Install the WWAN I/O board for systems enabled with 4G LTE.

3. Install the USB cable.

4. Install the coin-cell battery.

5. Install the I/O board.

6. Install the power adapter port.

7. Install the heatsink assembly.

8. Install the system fan.

9. Install the display assembly.

10. Install the I/O board cable.

11. Install the WWAN card for systems enabled with 4G LTE.

12. Install the WLAN card.

13. Install the hard-disk drive.

14. Install the M.2 SSD conversion plate.

15. Install the M.2 SSD conversion bracket.

16. Install the M.2 SSD.

17. Install the memory module.

18. Install the battery.

19. Install the base cover.

20. Install the SIM card tray for 4G LTE enabled systems.

21. Install the microSD-card.

22. Follow the procedure in after working inside your computer.

Removing and installing components 87

Display bezel

Removing the display bezel

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

6. Remove the WLAN card.

7. Remove the WWAN card for 4G LTE enabled systems.

8. Remove the I/O board cable.

9. Remove the display assembly.

About this task

The following images indicate the location of the display bezel and provide a visual representation of the removal procedure.

Steps

1. Use a plastic scribe to carefully pry open the top, left, and right sides of the display bezel.

CAUTION: When prying open the display bezel, ensure to pry along the outside edge of the display bezel

using your hand or a plastic scribe. Using a screw driver or any sharp object may damage the display cover.

2. Lift and remove the display bezel from the display assembly.

88 Removing and installing components

Installing the display bezel

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the display bezel and provides a visual representation of the installation procedure.

Steps

Align the display bezel with the display assembly. Gently snap the display bezel into place.

Next steps

1. Install the display assembly.

2. Install the I/O board cable.

3. Install the WWAN card for 4G LTE enabled systems.

4. Install the WLAN card.

5. Install the base cover.

6. Exit the service mode

7. Install the SIM card tray for 4G LTE enabled systems.

8. Install the microSD-card.

9. Follow the procedure in after working inside your computer.

Removing and installing components 89

Display panel

Removing the display panel

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Enter the service mode.

3. Remove the microSD-card.

4. Remove the SIM card tray for 4G LTE enabled systems.

5. Remove the base cover.

6. Remove the WLAN card.

7. Remove the WWAN card for 4G LTE enabled systems.

8. Remove the I/O board cable.

9. Remove the display assembly.

10. Remove the display bezel.

About this task

NOTE: The display panel is pre-assembled with the display brackets as a single service part. Do not pull and release the

Stretch Release (SR) Tapes from the display panel and separate the brackets from the display panel.

The following images indicate the location of the display panel and provide a visual representation of the removal procedure.

90 Removing and installing components

Removing and installing components 91

92 Removing and installing components

Steps

1. Remove the six (M2.5x2.5) and two (M2.5x3) screws that secure the left and right hinge brackets in place.

2. Gently flip over the display panel.

3. Peel the adhesive tape, open the latch and disconnect the display cable from the connector on the display panel.

4. Lift and remove the display panel from the display assembly.

Installing the display panel

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

NOTE: The display panel is pre-assembled with the display brackets as a single service part. Do not pull and release the

Stretch Release (SR) Tapes from the display panel and separate the brackets from the display panel.

The following images indicate the location of the display panel and provide a visual representation of the installation procedure.

Removing and installing components 93

94 Removing and installing components

Steps

1. Align and place the display panel on the display assembly.

2. Connect the display cable to the connector on the display panel, close the latch and affix the adhesive tape.

3. Install the six (M2.5x2.5) and two (M2.5x3) screws to secure the left and right hinge brackets in place.

4. Gently flip over the display panel.

Next steps

1. Install the display bezel.

2. Install the display assembly.

3. Install the I/O board cable.

4. Install the WWAN card for 4G LTE enabled systems..

5. Install the WLAN card.

6. Install the base cover.

7. Install the SIM card tray for 4G LTE enabled systems.

8. Install the microSD-card.

9. Exit the service mode

10. Follow the procedure in after working inside your computer.

Removing and installing components 95

Camera

Removing the camera

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

6. Remove the WLAN card.

7. Remove the WWAN card for 4G LTE enabled systems.

8. Remove the I/O board cable.

9. Remove the display assembly.

10. Remove the display bezel.

11. Remove the display panel.

About this task

The following image indicates the location of the camera and provides a visual representation of the removal procedure.

Steps

1. Peel the adhesive that secures the camera cable to the connector on the camera module.

2. Disconnect the camera cable from the connector on the camera module.

3. Peel the camera cable from the display back-cover.

4. Carefully pry loose and remove the camera module from the display back-cover.

Installing the camera

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

96 Removing and installing components

About this task

The following image indicates the location of the camera and provides a visual representation of the installation procedure.

Steps

1. Align and place the camera module into the slot on the display back-cover.

2. Connect the camera cable to the connector on the camera module.

3. Affix the adhesive tape to secure the camera cable to the connector on the camera module.

4. Align and affix the camera cable on the display back-cover.

Next steps

1. Install the display panel.

2. Install the display bezel.

3. Install the display assembly.

4. Install the I/O board cable.

5. Install the WWAN card for 4G LTE enabled systems.

6. Install the WLAN card.

7. Install the base cover.

8. Exit the service mode

9. Install the SIM card tray for 4G LTE enabled systems.

10. Install the microSD-card.

11. Follow the procedure in after working inside your computer.

Display cable

Removing the display cable

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

6. Remove the WLAN card.

7. Remove the WWAN card for 4G LTE enabled systems.

Removing and installing components 97

8. Remove the I/O board cable.

9. Remove the display assembly.

10. Remove the display bezel.

11. Remove the display panel.

About this task

The following image indicates the location of the display cable and provides a visual representation of the removal procedure.

Steps

1. Disconnect the display cable from the connector on the system board.

2. Disconnect the display cable from the connector on the display panel.

3. Disconnect the display cable from the connector on the camera module.

Installing the display cable

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

98 Removing and installing components

About this task

The following image indicates the location of the display cable and provides a visual representation of the installation procedure.

Steps

1. Connect the display cable from the connector on the camera module.

2. Connect the display cable from the connector on the display panel.

3. Connect the display cable from the connector on the system board.

Next steps

1. Install the display panel.

2. Install the display bezel.

3. Install the display assembly.

4. Install the I/O board cable.

5. Install the WWAN card for 4G LTE enabled systems. .

6. Install the WLAN card.

7. Install the base cover.

8. Exit the service mode

9. Install the SIM card tray for 4G LTE enabled systems.

10. Install the microSD-card.

11. Follow the procedure in after working inside your computer.

Removing and installing components 99

Display back-cover

Removing the display back-cover

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the microSD-card.

3. Remove the SIM card tray for 4G LTE enabled systems.

4. Enter the service mode.

5. Remove the base cover.

6. Remove the WLAN card.

7. Remove the WWAN card for 4G LTE enabled systems.

8. Remove the I/O board cable.

9. Remove the display assembly.

10. Remove the display bezel.

11. Remove the display panel.

12. Remove the camera.

13. Remove the display cable.

About this task

The following images indicate the location of the display back-cover and provide a visual representation of the removal

procedure.

Steps

After performing the preceding steps, you are left with the base cover assembly.

Installing the display back-cover

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

100 Removing and installing components

About this task

The following image indicates the location of the display back-cover and provides a visual representation of the installation

procedure.

Steps

After performing the succeeding steps, you are left with the base cover assembly.

Next steps

1. Install the display cable.

2. Install the camera.

3. Install the display panel.

4. Install the display bezel.

5. Install the display assembly.

6. Install the I/O board cable.

7. Install the WWAN card for 4G LTE enabled systems. .

8. Install the WLAN card.

9. Install the base cover.

10. Exit the service mode

11. Install the SIM card tray for 4G LTE enabled systems.

12. Install the microSD-card.

13. Follow the procedure in after working inside your computer.

Removing and installing components 101

Drivers and downloads

When troubleshooting, downloading, or installing drivers, it is recommended that you read the Dell knowledge base article,

Drivers and Downloads FAQs .

102 Drivers and downloads

BIOS setup

CAUTION: Unless you are an expert computer user, do not change the settings in the BIOS Setup program.

Certain changes can make your computer work incorrectly.

NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not be displayed.

NOTE: Before you change BIOS Setup program, it is recommended that you write down the BIOS Setup program screen

information for future reference.

Use the BIOS Setup program for the following purposes:

●Get information about the hardware installed in your computer, such as the amount of RAM and the size of the hard drive.

●Change the system configuration information.

●Set or change a user-selectable option, such as the user password, type of hard drive installed, and enabling or disabling

base devices.

BIOS overview

The BIOS manages data flow between the computer's operating system and attached devices such as hard disk, video adapter,

keyboard, mouse, and printer.

Entering BIOS setup program

Steps

1. Turn on your computer.

2. Press F2 immediately to enter the BIOS setup program.

NOTE: If you wait too long and the operating system logo appears, continue to wait until you see the desktop. Then,

turn off your computer and try again.

Navigation keys

NOTE: For most of the System Setup options, changes that you make are recorded but do not take effect until you restart

the system.

Table 4. Navigation keys

Keys Navigation

Up arrow Moves to the previous field.

Down arrow Moves to the next field.

Enter Selects a value in the selected field (if applicable) or follow

the link in the field.

Spacebar Expands or collapses a drop-down list, if applicable.

Tab Moves to the next focus area.

NOTE: For the standard graphics browser only.

BIOS setup 103

Table 4. Navigation keys (continued)

Keys Navigation

Esc Moves to the previous page until you view the main screen.

Pressing Esc in the main screen displays a message that

prompts you to save any unsaved changes and restarts the

system.

One time boot menu

To enter one time boot menu, turn on your computer, and then press F12 immediately.

NOTE: It is recommended to shutdown the computer if it is on.

The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot menu options

are:

●Removable Drive (if available)

●STXXXX Drive (if available)

NOTE: XXX denotes the SATA drive number.

●Optical Drive (if available)

●SATA Hard Drive (if available)

●Diagnostics

The boot sequence screen also displays the option to access the System Setup screen.

System setup options

NOTE: Depending on your system and its installed devices, the items that are listed in this section may or may not appear.

Table 5. System setup options—System information menu

Overview

Latitude 3520

BIOS Version Displays the BIOS version number.

Service Tag Displays the Service Tag of the system.

Asset Tag Displays the Asset Tag of the system.

Manufacture Date Displays the manufacture date of the system.

Ownership Date Displays the ownership date of the system.

Express Service Code Displays the express service code of the system.

Ownership Tag Displays the Ownership Tag of the system.

Signed Firmware Update Displays whether the Signed Firmware Update is enabled on your system.

Battery Information

Primary Displays that battery is primary.

Battery Level Displays the battery level of the system.

Battery State Displays the battery state of the system.

Health Displays the battery health of the system.

AC Adapter Displays whether the AC adapter is connected or not.

Processor Information

Processor Type Displays the processor type.

104 BIOS setup

Table 5. System setup options—System information menu (continued)

Overview

Maximum Clock Speed Displays the maximum processor clock speed.

Minimum Clock Speed Displays the minimum processor clock speed.

Current Clock Speed Displays the current processor clock speed.

Core Count Displays the number of cores on the processor.

Processor ID Displays the processor identification code.

Processor L2 Cache Displays the processor L2 Cache size.

Processor L3 Cache Displays the processor L3 Cache size.

Microcode Version Displays the microcode version.

Intel Hyper-Threading Capable Displays whether the processor is Hyper-Threading (HT) capable.

64-Bit Technology Displays whether 64-bit technology is used.

Memory Information

Memory Installed Displays the total system memory installed.

Memory Available Displays the total system memory available.

Memory Speed Displays the memory speed.

Memory Channel Mode Displays single or dual channel mode.

Memory Technology Displays the technology that is used for the memory.

DIMM SLOT 1 Displays DIMM slot information.

DIMM SLOT 2 Displays DIMM slot information.

Devices Information

Panel Type Displays the Panel Type of the system.

Video Controller Displays the video controller type of the system.

Video Memory Displays the video memory information of the system.

Wi-Fi Device Displays the wireless device information of the system.

Native Resolution Displays the native resolution of the system.

Video BIOS Version Displays the video BIOS version of the system.

Audio Controller Displays the audio controller information of the system.

Bluetooth Device Displays the Bluetooth device information of the system.

LOM MAC Address Displays the LAN On Motherboard (LOM) MAC address of the system.

Pass Through MAC Address Displays the pass through MAC address of the system.

Cellular Device Displays the M.2 PCIe SSD information of the system.

dGPU Video Controller (For systems with

discrete video card only)

Displays the video controller information.

Table 6. System setup options—Boot Configuration menu

Boot Configuration

Boot Sequence

Boot mode Displays the boot mode.

NOTE: Legacy Boot mode is not supported on this platform.

Boot Sequence Displays the boot sequence.

Secure Digital (SD) Card Boot Enable or disable the SD card read-only boot.

BIOS setup 105

Table 6. System setup options—Boot Configuration menu (continued)

Boot Configuration

By default, the Secure Digital (SD) Card Boot option is not enabled.

Secure Boot

Enable Secure Boot Enable or disable the secure boot feature.

By default, the option is disabled.

Secure Boot Mode Allows you to modify the secure boot mode options.

By default, the Deployed Mode is enabled.

By default, the Audit Mode is disabled.

Expert Key Management

Enable Custom Mode Enable or disable custom mode.

By default, the custom mode option is not enabled.

Custom Mode Key Management Allows you to select the custom values for expert key management.

Table 7. System setup options—Integrated Devices menu

Integrated Devices

Date/Time Displays the current date in MM/DD/YYYY format and current time in

HH:MM:SS AM/PM format.

Camera Enables or disable the camera.

By default, the Enable Camera option is selected

Audio

Enable Audio Enable or disable the integrated audio controller.

By default, the Enable Audio option is enabled.

By default, the Enable Microphone option is enabled.

By default, the Enable Internal Speaker option is enabled.

USB Configuration ●Enable or disable booting from USB mass storage devices that are

connected to external USB ports.

By default, the Enable External USB Ports option is enabled.

●Enable or disable booting from USB mass storage devices such as external

hard drive, optical drive, and USB drive.

By default, the Enable USB Boot Support option is enabled.

Disable USB4 PCIE Tunneling Disable the USB4 PCIE Tunneling option. By default, this option is disabled.

Video/Power only on Type-C Ports Enable or disable the Type-C port functionality to video or only power. By

default, the Video/Power only on Type-C Ports option is disabled.

Miscellaneous Devices

Enable Fingerprint Reader Device (For

systems with discrete video card only)

Enables Fingerprint Reader Device. This option is enabled by default.

Table 8. System setup options—Storage menu

Storage

SATA/NVMe Operation

SATA/NVMe Operation Set the operating mode of the integrated storage device controller.

By default, the RAID On option is enabled.

106 BIOS setup

Table 8. System setup options—Storage menu (continued)

Storage

Storage interface

Port Enablement This page allows you to enable the onboard drives.

By default, the SATA-1 option is enabled.

By default, the M.2 PCIe SSD-1 option is enabled.

SMART Reporting

Enable SMART Reporting Enable or disable Self-Monitoring, Analysis, and Reporting Technology

(SMART) during system startup.

By default, the Enable SMART Reporting option is disabled.

Drive Information

SATA-1

Type Displays the SATA type information of the system.

Device Displays the SATA device information of the system.

M.2 PCIe SSD-1

Type Displays the M.2 PCIe SSD type information of the system.

Device Displays the M.2 PCIe SSD device information of the system.

Enable Hard Drive Free Fall

Protection

Enable Hard Drive Free Fall Protection Allows you to enable Hard Drive Free Fall Protection feature.

By default, the Enable Hard Drive Free Fall Protection option is selected.

Enable MediaCard Enable or disable the media card in read-only state.

By default, the Secure Digital (SD) Card option is enabled.

Table 9. System setup options—Display menu

Display

Display Brightness

Brightness on battery power Enable to set screen brightness when the system is running on

battery power.

Brightness on AC power Enable to set screen brightness when the system is running on

AC power.

Touchscreen Enable or disable touchscreen for the operating system.

Touchscreen will always work in the BIOS setup irrespective

of this setting. This option is enabled by default.

EcoPower

Enable EcoPower Enable or disabled EcoPower feature. This option is enabled by

default.

Full Screen Logo Enable or disable full screen logo.

By default, the option is disabled.

Table 10. System setup options—Connection menu

Connection

Network Controller Configuration

BIOS setup 107

Table 10. System setup options—Connection menu (continued)

Connection

Integrated NIC If enabled, UEFI network protocols are installed and available, allowing pre-OS

and early OS networking features to use any enabled NICs. The option Enable

with PXE is enabled by default.

Wireless Device Enable

WWAN/GPS (For systems with discrete

video card only)

Enable or disable the internal WWAN/GPS device. By default, the option

enabled. The WWAN Bus Mode option is used to set the interface type of

the WWAN card. By default, the option Bus Mode PCIe is enabled.

WLAN Enable or disable the internal WLAN device.

By default, the option enabled.

Bluetooth Enable or disable the internal Bluetooth device.

By default, the option enabled.

Enable UEFI Network Stack Enable or disable UEFI Network Stack.

By default, the Enable UEFI Network Stack option is enabled.

Wireless Radio Control

Control WLAN radio Sense the connection of the system to a wired network and subsequently

disable the selected wireless radios (WLAN).

By default, the option is disabled.

Control WWAN radio Sense the connection of the system to a wired network and subsequently

disable the selected wireless radios (WWAN).

By default, the option is disabled.

HTTPs Boot Feature(For systems with

discrete video card only)

HTTPs Boot Enable or disable the HTTPs Boot feature.

By default, the HTTPs Boot option is enabled.

Table 11. System setup options—Power menu

Power

Battery configuration Enables the system to run on battery during peak power usage hours. Use the

table Custom Charge Start and Custom Charge Stop, to prevent AC power

usage between certain times of each day.

By default, the Adaptive option is enabled.

Advanced Configuration

Enable Advanced Battery Charge

Configuration

Enable or disable the advanced battery charge configuration.

By default, the Enable Advanced Battery Charge Configuration option is

disabled.

Peak Shift Enables the system to run on battery during peak power usage hours.

Enable Peak Shift By default, the Enable Peak Shift option is disabled.

USB PowerShare

Enable USB PowerShare Enable or disable the USB PowerShare.

By default, the Enable USB PowerShare option is disabled

Thermal Management Enables to cool the fan and processor heat management to adjust the system

performance, noise, and temperature.

108 BIOS setup

Table 11. System setup options—Power menu (continued)

Power

By default, the Optimized option is enabled.

USB Wake Support

Enable USB Wake Support Enables USB wake support.

By default, the Enable USB Wake Support option is disabled.

Wake on Dell USB-C Dock When enabled, connecting a Dell USB-C Dock will wake the system from

standby.

By default, the Wake on Dell USB-C Dock option is enabled.

Block Sleep Enables to block entering sleep (S3) mode in the operating system.

By default, the Block Sleep option is disabled.

Lid Switch Enable or disable the lid switch.

By default, the Lid Switch option is enabled.

Power On Lid Open Enables or diables system Power up from Off state when the lid is opened.

By default, the Power On Lid Open option is enabled.

Intel Speed Shift Technology Enable or disable the Intel speed shift technology support.

By default, the Intel Speed Shift Technology option is enabled.

Table 12. System setup options—Security menu

Security

TPM 2.0 Security

TPM 2.0 Security On Enable or disable TPM 2.0 security options.

By default, the TPM 2.0 Security On option is enabled.

PPI Bypass for Enable Commands Enables to control TPM Physical Presence Interface (PPI).

By default, the PPI Bypass for Enable Commands option is disabled.

PPI Bypass for Disable Commands Enables to control TPM Physical Presence Interface (PPI).

By default, the PPI Bypass for Disable Commands option is disabled.

Attestation Enable Enables to control whether the Trusted Platform Module (TPM) Endorsement

Hierarchy is available to the operating system.

By default, the Attestation Enable option is enabled.

Key Storage Enable Enables to control whether the Trusted Platform Module (TPM) Storage

Hierarchy is available to the operating system.

By default, the Key Storage Enable option is enabled.

SHA-256 BIOS and the TPM will use the SHA-256 hash algorithm to extend

measurements into the TPM PCRs during BIOS boot.

By default, the SHA-256 option is enabled.

Clear Enables to clear the TPM owner information and returns the TPM to the

default state.

By default, the Clear option is disabled.

PPI ByPass for Clear Commands Controls the TPM Physical Presence Interface (PPI).

By default, the PPI ByPass for clear Commands option is disabled.

TPM State Enables or disables TPM.

BIOS setup 109

Table 12. System setup options—Security menu (continued)

Security

By default, the option is enabled.

SMM Security Mitigation Enable or disable SMM Security Mitigation.

By default, the option is enabled.

Data Wipe on Next Boot

Start Data Wipe Enable or disable the data wipe on next boot.

By default, the option is disabled.

Absolute Enable or disable or permanently disable the BIOS module interface of the

optional Absolute Persistence Module service from Absolute software.

By default, the option is enabled.

UEFI Boot Path Security Controls whether the system will prompt the user to enter the admin password

(if set) when booting to a UEFI boot device from the F12 boot menu.

By default, the Always Except Internal HDD option is enabled.

Table 13. System setup options—Passwords menu

Passwords

Admin Password Set, change, or delete the administrator password.

System Password Set, change, or delete the system password.

Internal HDD-1 Password Set, change, or delete the Internal HDD-1 password.

NVMe SSD0 Set, change, or delete the NVMe SSD0 password.

Password Configuration

Upper Case Letter Reinforces password must have at least one upper case letter.

By default, the option is enabled.

Lower Case Letter Reinforces password must have at least one lower case letter.

By default, the option is enabled.

Digit Reinforces password must have at least one digit.

By default, the option is enabled.

Special Character Reinforces password must have at least one special character.

By default, the option is enabled.

Minimum Characters Set the minimum characters allowed for password.

Password Bypass When enabled, this always prompts for system and internal hard drive

passwords when powered on from the off state.

By default, the Disabled option is selected.

Password Changes

Enable Non-Admin Password Changes Enable or disable to change system and hard drive password without the need

for admin password.

By default, the option is disabled.

Admin Setup Lockout

Enable Admin Setup Lockout Enables administrators control over how their users can or cannot access BIOS

setup.

By default, the option is disabled.

110 BIOS setup

Table 13. System setup options—Passwords menu (continued)

Passwords

Master Password Lockout

Enable Master Password Lockout When enabled, this disables the master password support.

By default, the option is disabled.

Allow Non-Admin PSID Revert(For

systems with discrete video card only)

Enable Allow Non-Admin PSID Revert Controls access to the Physical Security ID (PSID) revert of NVMe hard-drives

from the Dell Security Manager prompt.

By default, the option is disabled.

Table 14. System setup options—Update, Recovery menu

Update, Recovery

UEFI Capsule Firmware Updates Enable or disable BIOS updates through UEFI capsule update packages.

By default, the option is enabled.

BIOS Recovery from Hard Drive Enables the user to recover from certain corrupted BIOS conditions from a

recovery file on the user primary hard drive or an external USB key.

By default, the option is enabled.

BIOS Downgrade

Allow BIOS Downgrade Enable or disable the flashing of the system firmware to previous revision is

blocked.

By default, the option is enabled.

SupportAssist OS Recovery Enable or disable the boot flow for SupportAssist OS Recovery tool in the

event of certain system errors.

By default, the option is enabled.

BIOSConnect Enable or disable cloud Service operating system recovery if the main operating

system fails to boot with the number of failures equal to or greater than the

value specified by the Auto operating system Recovery Threshold setup option

and local Service operating system does not boot or is not installed.

By default, the option is enabled.

Dell Auto operating system Recovery

Threshold

Controls the automatic boot flow for SupportAssist System Resolution Console

and for Dell operating system Recovery Tool.

By default, the threshold value is set to 2.

Table 15. System setup options—System Management menu

System Management

Service Tag Display the Service Tag of the system.

Asset Tag Create a system Asset Tag.

AC Behavior

Wake on AC Enable or disable the wake on AC option.

By default, the option is disabled.

Wake on LAN

Wake on LAN Enable or disable the system to power on by special LAN signals when it

receives a wakeup signal from the WLAN.

By default, the Disabled option is selected.

BIOS setup 111

Table 15. System setup options—System Management menu (continued)

System Management

Auto on Time Enable to set the system to turn on automatically every day or on a preselected

date and time. This option can be configured only if the Auto On Time is set to

Everyday, Weekdays, or Selected Days.

By default, the option is disabled.

Table 16. System setup options—Keyboard menu

Keyboard

Numlock Options By default, the Numlock option is enabled.

Fn Lock Options By default, the Fn lock option is enabled.

Lock Mode By default, Lock Mode Secondary is enabled.

Keyboard Illumination Enables to change the keyboard illumination settings.

By default, the Bright option is enabled.

Keyboard Backlight Timeout on AC Set the timeout value for the keyboard backlight when an AC adapter is

connected to the system.

By default, the 1 minute option is enabled.

Keyboard Backlight Timeout on

Battery

Set the timeout value for the keyboard backlight when the is running only on

battery power.

By default, the 1 minute option is enabled.

Table 17. System setup options—Pre-boot Behavior menu

Pre-boot Behavior

Adapter Warnings

Enable Adapter Warnings Enable or disable the warning messages during boot when the adapters with

less power capacity are detected.

By default, the option is enabled.

Warning and Errors Enable or disable the action to be done when a warning or error is encountered.

By default, the Prompt on Warnings and Errors option is enabled.

USB-C Warnings

Enable Dock Warning Messages By default, the option is enabled.

Fastboot Enable to set the speed of the boot process.

By default, the Thorough option is enabled.

Extend BIOS POST Time Set the BIOS POST time.

By default, the 0 seconds option is enabled.

MAC Address Pass-Through Replaces the external NIC MAC address with the selected MAC address from

the system.

By default, the System Unique MAC Address option is enabled.

Table 18. System setup options—Virtualization menu

Virtualization

Intel Virtualization Technology

Enable Intel Virtualization Technology

(VT)

Specify whether a Virtual Machine Monitor (VMM) can use the additional

hardware capabilities that are provided by Intel Virtualization Technology.

112 BIOS setup

Table 18. System setup options—Virtualization menu (continued)

Virtualization

By default, the option is enabled.

VT for Direct I/O Specify whether a Virtual Machine Monitor (VMM) can use the additional

hardware capabilities that are provided by Intel Virtualization Technology for

Direct I/O.

By default, the option is enabled.

Table 19. System setup options—Performance menu

Performance

Multi Core Support

Active Cores Enables to change the number of CPU cores available to the operating system.

By default, the All Cores option is enabled.

Intel SpeedStep

Enable Intel SpeedStep Technology Enables the system to dynamically adjust processor voltage and core

frequency, decreasing average power consumption and heat production.

By default, the option is enabled.

C-States Control

Enable C-State Control Enable or disable additional processor sleep states.

By default, the option is enabled.

Enable Adaptive C-States for Discrete

Graphics

Enable or disable usage of Discrete graphics and requires AC adapter due to

higher energy consumption.

By default, the option is enabled.

Intel TurbocBoost Technology

Enable Intel Turbo Boost Technology Enable or disable Intel TurboBoost mode of the processor.

By default, the option is enabled.

Intel Hyper-Threading Technology

Enable Intel Hyper-Threading Technology Enable or disable Hyper-Threading in the processor.

By default, the option is enabled.

Table 20. System setup options—System Logs menu

System Logs

BIOS Event Log

Clear Bios Event Log Display BIOS events.

By default, the Keep option is enabled.

Thermal Event Log

Clear Thermal Event Log Display Thermal events.

By default, the Keep option is enabled.

Power Event Log

Clear Power Event Log Display power events.

By default, the Keep option is enabled.

License Information Displays the license information of the system.

BIOS setup 113

Updating the BIOS

Updating the BIOS in Windows

About this task

CAUTION: If BitLocker is not suspended before updating the BIOS, the next time you reboot the system it

will not recognize the BitLocker key. You will then be prompted to enter the recovery key to progress and the

system will ask for this on each reboot. If the recovery key is not known this can result in data loss or an

unnecessary operating system re-install. For more information on this subject, see Knowledge Article: https://

www.dell.com/support/article/sln153694

Steps

1. Go to www.dell.com/support.

2. Click Product support. In the Search support box, enter the Service Tag of your computer, and then click Search.

NOTE: If you do not have the Service Tag, use the SupportAssist feature to automatically identify your computer. You

can also use the product ID or manually browse for your computer model.

3. Click Drivers & Downloads. Expand Find drivers.

4. Select the operating system installed on your computer.

5. In the Category drop-down list, select BIOS.

6. Select the latest version of BIOS, and click Download to download the BIOS file for your computer.

7. After the download is complete, browse the folder where you saved the BIOS update file.

8. Double-click the BIOS update file icon and follow the on-screen instructions.

For more information, see knowledge base article 000124211 at www.dell.com/support.

Updating the BIOS in Linux and Ubuntu

To update the system BIOS on a computer that is installed with Linux or Ubuntu, see the knowledge base article 000131486 at

www.dell.com/support.

Updating the BIOS using the USB drive in Windows

About this task

CAUTION: If BitLocker is not suspended before updating the BIOS, the next time you reboot the system it

will not recognize the BitLocker key. You will then be prompted to enter the recovery key to progress and the

system will ask for this on each reboot. If the recovery key is not known this can result in data loss or an

unnecessary operating system re-install. For more information on this subject, see Knowledge Article: https://

www.dell.com/support/article/sln153694

Steps

1. Follow the procedure from step 1 to step 6 in Updating the BIOS in Windows to download the latest BIOS setup program file.

2. Create a bootable USB drive. For more information, see the knowledge base article 000145519 at www.dell.com/support.

3. Copy the BIOS setup program file to the bootable USB drive.

4. Connect the bootable USB drive to the computer that needs the BIOS update.

5. Restart the computer and press F12 .

6. Select the USB drive from the One Time Boot Menu.

7. Type the BIOS setup program filename and press Enter.

The BIOS Update Utility appears.

8. Follow the on-screen instructions to complete the BIOS update.

114 BIOS setup

Updating the BIOS from the F12 One-Time boot menu

Update your computer BIOS using the BIOS update.exe file that is copied to a FAT32 USB drive and booting from the F12

One-Time boot menu.

About this task

CAUTION: If BitLocker is not suspended before updating the BIOS, the next time you reboot the system it

will not recognize the BitLocker key. You will then be prompted to enter the recovery key to progress and the

system will ask for this on each reboot. If the recovery key is not known this can result in data loss or an

unnecessary operating system re-install. For more information on this subject, see Knowledge Article: https://

www.dell.com/support/article/sln153694

BIOS Update

You can run the BIOS update file from Windows using a bootable USB drive or you can also update the BIOS from the F12

One-Time boot menu on the computer.

Most of the Dell computers built after 2012 have this capability, and you can confirm by booting your computer to the F12

One-Time Boot Menu to see if BIOS FLASH UPDATE is listed as a boot option for your computer. If the option is listed, then the

BIOS supports this BIOS update option.

NOTE: Only computers with BIOS Flash Update option in the F12 One-Time boot menu can use this function.

Updating from the One-Time boot menu

To update your BIOS from the F12 One-Time boot menu, you need the following:

●USB drive formatted to the FAT32 file system (key does not have to be bootable)

●BIOS executable file that you downloaded from the Dell Support website and copied to the root of the USB drive

●AC power adapter that is connected to the computer

●Functional computer battery to flash the BIOS

Perform the following steps to perform the BIOS update flash process from the F12 menu:

CAUTION: Do not turn off the computer during the BIOS update process. The computer may not boot if you turn

off your computer.

Steps

1. From a turn off state, insert the USB drive where you copied the flash into a USB port of the computer.

2. Turn on the computer and press F12 to access the One-Time Boot Menu, select BIOS Update using the mouse or arrow keys

then press Enter.

The flash BIOS menu is displayed.

3. Click Flash from file.

4. Select external USB device.

5. Select the file and double-click the flash target file, and then click Submit.

6. Click Update BIOS. The computer restarts to flash the BIOS.

7. The computer will restart after the BIOS update is completed.

System and setup password

Table 21. System and setup password

Password type Description

System password Password that you must enter to log in to your system.

Setup password Password that you must enter to access and make changes to

the BIOS settings of your computer.

You can create a system password and a setup password to secure your computer.

BIOS setup 115

CAUTION: The password features provide a basic level of security for the data on your computer.

CAUTION: Anyone can access the data that is stored on your computer if it is not locked and left unattended.

NOTE: System and setup password feature is disabled.

Assigning a system setup password

Prerequisites

You can assign a new System or Admin Password only when the status is in Not Set.

About this task

To enter the system setup, press F12 immediately after a power-on or reboot.

Steps

1. In the System BIOS or System Setup screen, select Security and press Enter.

The Security screen is displayed.

2. Select System/Admin Password and create a password in the Enter the new password field.

Use the following guidelines to assign the system password:

●A password can have up to 32 characters.

●The password can contain the numbers 0 through 9.

●Only lower case letters are valid, upper case letters are not valid.

●Only the following special characters are valid: Space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

3. Type the system password that you entered earlier in the Confirm new password field and click OK.

4. Press Esc and a message prompt's you to save the changes.

5. Press Y to save the changes.

The computer restarts.

Deleting or changing an existing system setup password

Prerequisites

Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing

System and/or Setup password. You cannot delete or change an existing System or Setup password, if the Password Status is

Locked.

About this task

To enter the System Setup, press F12 immediately after a power-on or reboot.

Steps

1. In the System BIOS or System Setup screen, select System Security and press Enter.

The System Security screen is displayed.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password, update, or delete the existing system password, and press Enter or Tab.

4. Select Setup Password, update, or delete the existing setup password, and press Enter or Tab.

NOTE: If you change the System and/or Setup password, reenter the new password when prompted. If you delete the

System and/or Setup password, confirm the deletion when prompted.

5. Press Esc and a message prompts you to save the changes.

6. Press Y to save the changes and exit from System Setup.

The computer restarts.

116 BIOS setup

Clearing CMOS settings

About this task

CAUTION: Clearing CMOS settings will reset the BIOS settings on your computer.

Steps

1. Remove the base cover.

2. Disconnect the battery cable from the system board.

3. Remove the coin-cell battery.

4. Wait for one minute.

5. Replace the coin-cell battery.

6. Connect the battery cable to the system board.

7. Replace the base cover.

Clearing BIOS (System Setup) and System passwords

About this task

To clear the system or BIOS passwords, contact Dell technical support as described at www.dell.com/contactdell.

NOTE: For information on how to reset Windows or application passwords, refer to the documentation accompanying

Windows or your application.

BIOS setup 117

Troubleshooting

Handling swollen Lithium-ion batteries

Like most laptops, Dell laptops use lithium-ion batteries. One type of lithium-ion battery is the lithium-ion polymer battery.

Lithium-ion polymer batteries have increased in popularity in recent years and have become standard in the electronics industry

due to customer preferences for a slim form factor (especially with newer ultra-thin laptops) and long battery life. Inherent to

lithium-ion polymer battery technology is the potential for swelling of the battery cells.

Swollen battery may impact the performance of the laptop. To prevent possible further damage to the device enclosure or

internal components leading to malfunction, discontinue the use of the laptop and discharge it by disconnecting the AC adapter

and letting the battery drain.

Swollen batteries should not be used and should be replaced and disposed of properly. We recommend contacting Dell product

support for options to replace a swollen battery under the terms of the applicable warranty or service contract, including options

for replacement by a Dell authorized service technician.

The guidelines for handling and replacing Lithium-ion batteries are as follows:

●Exercise caution when handling Lithium-ion batteries.

●Discharge the battery before removing it from the system. To discharge the battery, unplug the AC adapter from the system

and operate the system only on battery power. When the system will no longer power on when the power button is pressed,

the battery is fully discharged.

●Do not crush, drop, mutilate, or penetrate the battery with foreign objects.

●Do not expose the battery to high temperatures, or disassemble battery packs and cells.

●Do not apply pressure to the surface of the battery.

●Do not bend the battery.

●Do not use tools of any type to pry on or against the battery.

●If a battery gets stuck in a device as a result of swelling, do not try to free it as puncturing, bending, or crushing a battery

can be dangerous.

●Do not attempt to reassemble a damaged or swollen battery into a laptop.

●Swollen batteries that are covered under warranty should be returned to Dell in an approved shipping container (provided

by Dell)—this is to comply with transportation regulations. Swollen batteries that are not covered under warranty should be

disposed of at an approved recycling center. Contact Dell product support at https://www.dell.com/support for assistance

and further instructions.

●Using a non-Dell or incompatible battery may increase the risk of fire or explosion. Replace the battery only with a

compatible battery purchased from Dell that is designed to work with your Dell computer. Do not use a battery from other

computers with your computer. Always purchase genuine batteries from https://www.dell.com or otherwise directly from

Dell.

Lithium-ion batteries can swell for various reasons such as age, number of charge cycles, or exposure to high heat. For more

information on how to improve the performance and lifespan of the laptop battery and to minimize the possibility of occurrence

of the issue, see Dell Laptop Battery - Frequently Asked Questions.

Dell SupportAssist Pre-boot System Performance

Check diagnostics

About this task

SupportAssist diagnostics (also known as system diagnostics) performs a complete check of your hardware. The Dell

SupportAssist Pre-boot System Performance Check diagnostics is embedded with the BIOS and is launched by the BIOS

internally. The embedded system diagnostics provides a set of options for particular devices or device groups allowing you to:

●Run tests automatically or in an interactive mode

●Repeat tests

●Display or save test results

118 Troubleshooting

●Run thorough tests to introduce additional test options to provide extra information about the failed device(s)

●View status messages that inform you if tests are completed successfully

●View error messages that inform you of problems encountered during testing

NOTE: Some tests for specific devices require user interaction. Always ensure that you are present at the computer

terminal when the diagnostic tests are performed.

For more information, see https://www.dell.com/support/kbdoc/000180971.

Running the SupportAssist Pre-Boot System Performance Check

Steps

1. Turn on your computer.

2. As the computer boots, press the F12 key as the Dell logo appears.

3. On the boot menu screen, select the Diagnostics option.

4. Click the arrow at the bottom left corner.

Diagnostics front page is displayed.

5. Click the arrow in the lower-right corner to go to the page listing.

The items detected are listed.

6. To run a diagnostic test on a specific device, press Esc and click Yes to stop the diagnostic test.

7. Select the device from the left pane and click Run Tests.

8. If there are any issues, error codes are displayed.

Note the error code and validation number and contact Dell.

Built-in self-test (BIST)

M-BIST

M-BIST (Built In Self-Test) is the system board's built-in self-test diagnostics tool that improves the diagnostics accuracy of

system board embedded controller (EC) failures.

NOTE: M-BIST can be manually initiated before POST (Power On Self Test).

How to run M-BIST

NOTE: M-BIST must be initiated on the system from a power-off state either connected to AC power or with battery only.

1. Press and hold both the M key on the keyboard and the power button to initiate M-BIST.

2. With both the M key and the power button held down, the battery indicator LED may exhibit two states:

a. OFF: No fault detected with the system board

b. AMBER: Indicates a problem with the system board

3. If there is a failure with the system board, the battery status LED will flash one of the following error codes for 30 seconds:

Table 22. LED error codes

Blinking Pattern Possible Problem

Amber White

2 1 CPU Failure

2 8 LCD Power Rail Failure

1 1 TPM Detection Failure

2 4 Unrecoverable SPI Failure

4. If there is no failure with the system board, the LCD will cycle through the solid color screens described in the LCD-BIST

section for 30 seconds and then power off.

Troubleshooting 119

LCD Power rail test (L-BIST)

L-BIST is an enhancement to the single LED error code diagnostics and is automatically initiated during POST. L-BIST will check

the LCD power rail. If there is no power being supplied to the LCD (i.e., the L-BIST circuit fails), the battery status LED will flash

either an error code [2,8] or an error code [2,7].

NOTE: If L-BIST fails, LCD-BIST cannot function as no power will be supplied to the LCD.

How to invoke L-BIST Test:

1. Press the power button to start the system.

2. If the system does not start up normally, look at the battery status LED:

●If the battery status LED flashes an error code [2,7], the display cable may not be connected properly.

●If the battery status LED flashes an error code [2,8], there is a failure on the LCD power rail of the system board, hence

there is no power supplied to the LCD.

3. For cases, when a [2,7] error code is shown, check to see if the display cable is properly connected.

4. For cases when a [2,8] error code is shown, replace the system board.

LCD Built-in Self Test (BIST)

Dell laptops have a built-in diagnostic tool that helps you determine if the screen abnormality you are experiencing is an inherent

problem with the LCD (screen) of the Dell laptop or with the video card (GPU) and PC settings.

When you notice screen abnormalities like flickering, distortion, clarity issues, fuzzy or blurry image, horizontal or vertical lines,

color fade etc., it is always a good practice to isolate the LCD (screen) by running the Built-In Self Test (BIST).

How to invoke LCD BIST Test

1. Power off the Dell laptop.

2. Disconnect any peripherals that are connected to the laptop. Connect only the AC adapter (charger) to the laptop.

3. Ensure that the LCD (screen) is clean (no dust particles on the surface of the screen).

4. Press and hold D key and Power on the laptop to enter LCD built-in self test (BIST) mode. Continue to hold the D key, until

the system boots up.

5. The screen will display solid colors and change colors on the entire screen to white, black, red, green, and blue twice.

6. Then it will display the colors white, black and red.

7. Carefully inspect the screen for abnormalities (any lines, fuzzy color or distortion on the screen).

8. At the end of the last solid color (red), the system will shut down.

NOTE: Dell SupportAssist Pre-boot diagnostics upon launch, initiates an LCD BIST first, expecting a user intervention

confirm functionality of the LCD.

System-diagnostic lights

Table 23. System-diagnostic lights

Blinking pattern

Problem description Suggested resolutionAmber White

1 1 TPM detection failure Replace the system board.

1 2 Unrecoverable SPI Flash

Failure

Replace the system board.

1 5 EC unable to program i-Fuse Replace the system board.

120 Troubleshooting

Table 23. System-diagnostic lights (continued)

Blinking pattern

Problem description Suggested resolutionAmber White

1 6 Generic catch-all for

ungraceful EC code flow

errors

Disconnect all power source

(AC, battery, coin cell) and

drain flea power by pressing

and holding down power

button for 3~5 seconds.

2 1 CPU failure ●Run the Dell Support

Assist/Dell Diagnostics

tool.

●If problem persists,

replace the system board.

2 2 System board failure (included

BIOS corruption or ROM

error)

●Flash latest BIOS version

●If problem persists,

replace the system board.

2 3 No memory/RAM detected ●Confirm that the memory

module is installed

properly.

●If problem persists,

replace the memory

module.

2 4 Memory/RAM failure ●Reset and swap memory

modules among the slots.

●If problem persists,

replace the memory

module.

2 5 Invalid memory installed ●Reset and swap memory

modules among the slots.

●If problem persists,

replace the memory

module.

2 6 System board/Chipset Error Replace the system board.

2 7 LCD failure (SBIOS message) Replace the LCD module.

2 8 LCD failure (EC detection of

power rail failure)

Replace the system board.

3 1 CMOS battery failure ●Reset the main battery

connection.

●If problem persists,

replace the main battery.

3 2 PCI or Video card/chip failure Replace the system board.

3 3 BIOS Recovery image not

found

●Flash latest BIOS version

●If problem persists,

replace the system board.

3 4 BIOS Recovery image found

but invalid

●Flash latest BIOS version

●If problem persists,

replace the system board.

3 5 Power rail failure Replace the system board.

3 6 Flash corruption detected by

SBIOS.

●Press power button for

over 25 seconds to do

Troubleshooting 121

Table 23. System-diagnostic lights (continued)

Blinking pattern

Problem description Suggested resolutionAmber White

RTC reset. If problem

persists, replace the

system board.

●Disconnect all power

source (AC, battery, coin

cell) and drain flea power

by pressing and holding

down power button 3~5

seconds to ensure all

power are drained.

●Run "BIOS recovery from

USB", and the instructions

are in the website Dell

support.

●If problem persists,

replace the system board.

3 7 Timeout waiting on ME to

reply to HECI message.

Replace the system board.

NOTE: Blinking 3-3-3 LEDs on Lock LED (Caps-Lock or Nums-Lock), Power button LED (without Fingerprint reader), and

Diagnostic LED indicates failure to provide input during LCD panel test on Dell SupportAssist Pre-boot System Performance

Check diagnostics.

Recovering the operating system

When your computer is unable to boot to the operating system even after repeated attempts, it automatically starts Dell

SupportAssist OS Recovery.

Dell SupportAssist OS Recovery is a standalone tool that is preinstalled in all Dell computers installed with Windows operating

system. It consists of tools to diagnose and troubleshoot issues that may occur before your computer boots to the operating

system. It enables you to diagnose hardware issues, repair your computer, back up your files, or restore your computer to its

factory state.

You can also download it from the Dell Support website to troubleshoot and fix your computer when it fails to boot into their

primary operating system due to software or hardware failures.

For more information about the Dell SupportAssist OS Recovery, see Dell SupportAssist OS Recovery User's Guide at

www.dell.com/serviceabilitytools. Click SupportAssist and then, click SupportAssist OS Recovery.

Real-Time Clock (RTC Reset)

The Real Time Clock (RTC) reset function allows you or the service technician to recover Dell Latitude systems from No

POST/No Power/No Boot situations. The legacy jumper enabled RTC reset has been retired on these models.

Start the RTC reset with the system powered off and connected to AC power. Press and hold the power button for thirty (30)

seconds. The system RTC Reset occurs after you release the power button.

Backup media and recovery options

It is recommended to create a recovery drive to troubleshoot and fix problems that may occur with Windows. Dell proposes

multiple options for recovering Windows operating system on your Dell PC. For more information. see Dell Windows Backup

Media and Recovery Options.

122 Troubleshooting

WiFi power cycle

About this task

If your computer is unable to access the internet due to WiFi connectivity issues a WiFi power cycle procedure may be

performed. The following procedure provides the instructions on how to conduct a WiFi power cycle:

NOTE: Some ISPs (Internet Service Providers) provide a modem/router combo device.

Steps

1. Turn off your computer.

2. Turn off the modem.

3. Turn off the wireless router.

4. Wait for 30 seconds.

5. Turn on the wireless router.

6. Turn on the modem.

7. Turn on your computer.

Drain residual flea power (perform hard reset)

About this task

Flea power is the residual static electricity that remains in the computer even after it has been powered off and the battery is

removed.

For your safety, and to protect the sensitive electronic components in your computer, you are requested to drain residual flea

power before removing or replacing any components in your computer.

Draining residual flea power, also known as a performing a "hard reset", is also a common troubleshooting step if your computer

does not power on or boot into the operating system.

To drain residual flea power (perform a hard reset)

Steps

1. Turn off your computer.

2. Disconnect the power adapter from your computer.

3. Remove the base cover.

4. Remove the battery.

5. Press and hold the power button for 20 seconds to drain the flea power.

6. Install the battery.

7. Install the base cover.

8. Connect the power adapter to your computer.

9. Turn on your computer.

NOTE: For more information about performing a hard reset, see the knowledge base article 000130881 at

www.dell.com/support.

Troubleshooting 123

Getting help and contacting Dell

Self-help resources

You can get information and help on Dell products and services using these self-help resources:

Table 24. Self-help resources

Self-help resources Resource location

Information about Dell products and services www.dell.com

My Dell app

Tips

Contact Support In Windows search, type Contact Support, and press

Enter.

Online help for operating system www.dell.com/support/windows

Access top solutions, diagnostics, drivers and downloads, and

learn more about your computer through videos, manuals and

documents.

Your Dell computer is uniquely identified by a Service Tag or

Express Service Code. To view relevant support resources for

your Dell computer, enter the Service Tag or Express Service

Code at www.dell.com/support.

For more information on how to find the Service Tag for your

computer, see Locate the Service Tag on your computer.

Dell knowledge base articles for a variety of computer

concerns

1. Go to www.dell.com/support.

2. On the menu bar at the top of the Support page, select

Support > Knowledge Base.

3. In the Search field on the Knowledge Base page, type the

keyword, topic, or model number, and then click or tap the

search icon to view the related articles.

Contacting Dell

To contact Dell for sales, technical support, or customer service issues, see www.dell.com/contactdell.

NOTE: Availability varies by country/region and product, and some services may not be available in your country/region.

NOTE: If you do not have an active Internet connection, you can find contact information about your purchase invoice,

packing slip, bill, or Dell product catalog.

124 Getting help and contacting Dell

Table of Contents

DELL 3520 User Manual

Related Manuals