Table of Contents
- Precision 3530 Service Manual
- Working on your computer
- Technology and components
- Disassembly and reassembly
- Subscriber Identity Module(SIM) board
- Base cover
- Battery
- Solid State Drive — optional
- WLAN card
- WWAN card
- Coin-cell battery
- Memory modules
- Keyboard
- Heat sink
- Power connector port
- Chassis frame
- System board
- Touchpad
- SmartCard module
- LED board
- Speaker
- Hinge cap
- Display assembly
- Display bezel
- Display hinges
- Display panel
- Display (eDP) cable
- Camera
- Display back cover assembly
- Palm rest
- Troubleshooting
- Getting help
DELL 3530 User Manual
Displayed below is the user manual for 3530 by DELL which is a product in the Notebooks category. This manual has pages.
Related Manuals
Precision 3530
Service Manual
Regulatory Model: P60F
Regulatory Type: P60F002
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2018 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks
may be trademarks of their respective owners.
2018 - 03
Rev. A00
Contents
1 Working on your computer............................................................................................................................. 6
Safety instructions.............................................................................................................................................................6
Turning o your computer — Windows 10.....................................................................................................................6
Before working inside your computer..............................................................................................................................6
After working inside your computer.................................................................................................................................7
2 Technology and components..........................................................................................................................8
Power adapter.................................................................................................................................................................... 8
DDR4................................................................................................................................................................................... 8
DDR4 Details.................................................................................................................................................................8
Memory Errors..............................................................................................................................................................9
HDMI 1.4- HDMI 2.0...........................................................................................................................................................9
HDMI 1.4- HDMI 2.0 Features...................................................................................................................................10
Advantages of HDMI..................................................................................................................................................10
USB features.....................................................................................................................................................................10
USB 3.0/USB 3.1 Gen 1 (SuperSpeed USB)............................................................................................................10
Speed............................................................................................................................................................................ 11
Applications.................................................................................................................................................................. 11
Compatibility................................................................................................................................................................12
Advantages of Displayport over USB Type-C......................................................................................................... 12
USB Type-C.......................................................................................................................................................................12
Alternate Mode........................................................................................................................................................... 12
USB Power Delivery................................................................................................................................................... 13
USB Type-C and USB 3.1........................................................................................................................................... 13
3 Disassembly and reassembly........................................................................................................................ 14
Subscriber Identity Module(SIM) board........................................................................................................................ 14
Installing the Subscriber Identication Module card...............................................................................................14
Removing the Subscriber Identication Module card............................................................................................ 14
Base cover.........................................................................................................................................................................15
Removing the base cover..........................................................................................................................................15
Installing the base cover............................................................................................................................................ 16
Battery............................................................................................................................................................................... 16
Removing the battery................................................................................................................................................ 16
Installing the battery...................................................................................................................................................17
Solid State Drive — optional ..........................................................................................................................................17
Removing the M.2 Solid State Drive - SSD.............................................................................................................17
Installing the M.2 Solid State Drive - SSD............................................................................................................... 19
WLAN card........................................................................................................................................................................19
Removing the WLAN card.........................................................................................................................................19
Installing the WLAN card.......................................................................................................................................... 20
WWAN card.......................................................................................................................................................................21
Removing the WWAN card....................................................................................................................................... 21
Contents 3
Installing the WLAN card.......................................................................................................................................... 22
Coin-cell battery...............................................................................................................................................................22
Removing the coin cell battery.................................................................................................................................22
Installing the coin cell battery................................................................................................................................... 23
Memory modules..............................................................................................................................................................23
Removing the memory module................................................................................................................................ 23
Installing the memory module...................................................................................................................................24
Keyboard........................................................................................................................................................................... 24
Removing keyboard lattice........................................................................................................................................24
Removing the keyboard............................................................................................................................................ 25
Installing the keyboard............................................................................................................................................... 27
Installing the keyboard trim....................................................................................................................................... 27
Heat sink ...........................................................................................................................................................................27
Removing the heat sink ............................................................................................................................................27
Installing the heat sink ..............................................................................................................................................29
Power connector port..................................................................................................................................................... 29
Removing the power connector port...................................................................................................................... 29
Installing the power connector port........................................................................................................................ 30
Chassis frame...................................................................................................................................................................30
Removing the chassis frame.................................................................................................................................... 30
Installing the chassis frame.......................................................................................................................................32
System board....................................................................................................................................................................32
Removing the system board.....................................................................................................................................32
Installing the system board....................................................................................................................................... 35
Touchpad...........................................................................................................................................................................35
Removing the touchpad............................................................................................................................................35
Installing the touchpad.............................................................................................................................................. 37
SmartCard module........................................................................................................................................................... 37
Removing the SmartCard reader............................................................................................................................. 37
Installing the SmartCard reader............................................................................................................................... 39
LED board......................................................................................................................................................................... 39
Removing the LED board..........................................................................................................................................39
Installing the LED board............................................................................................................................................ 40
Speaker.............................................................................................................................................................................. 41
Removing the speaker............................................................................................................................................... 41
Installing the speaker.................................................................................................................................................42
Hinge cap.......................................................................................................................................................................... 42
Removing the hinge cap........................................................................................................................................... 42
Installing the hinge cap..............................................................................................................................................43
Display assembly.............................................................................................................................................................. 43
Removing the display assembly................................................................................................................................43
Installing the display assembly..................................................................................................................................46
Display bezel..................................................................................................................................................................... 46
Removing display bezel ............................................................................................................................................ 46
Installing display bezel ...............................................................................................................................................47
Display hinges................................................................................................................................................................... 47
Removing the display hinge...................................................................................................................................... 47
4Contents
Installing the display hinge........................................................................................................................................ 48
Display panel.....................................................................................................................................................................49
Removing the display panel...................................................................................................................................... 49
Installing the display panel........................................................................................................................................ 50
Display (eDP) cable...........................................................................................................................................................51
Removing the eDP cable........................................................................................................................................... 51
Installing the eDP cable..............................................................................................................................................51
Camera..............................................................................................................................................................................52
Removing camera...................................................................................................................................................... 52
Installing camera.........................................................................................................................................................53
Display back cover assembly.......................................................................................................................................... 53
Removing the display back cover assembly........................................................................................................... 53
Installing the display back cover assembly..............................................................................................................54
Palm rest........................................................................................................................................................................... 54
Replacing the palm rest.............................................................................................................................................54
4 Troubleshooting........................................................................................................................................... 56
Enhanced Pre-Boot System Assessment — ePSA diagnostics................................................................................56
Running the ePSA Diagnostics................................................................................................................................ 56
Real Time Clock reset......................................................................................................................................................56
5 Getting help.................................................................................................................................................58
Contacting Dell.................................................................................................................................................................58
Contents 5
Working on your computer
Safety instructions
Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise
noted, each procedure included in this document assumes that the following conditions exist:
• You have read the safety information that shipped with your computer.
• A component can be replaced or, if purchased separately, installed by performing the removal procedure in reverse order.
WARNING: Disconnect all power sources before opening the computer cover or panels. After you nish working inside the
computer, replace all covers, panels, and screws before connecting to the power source.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional
safety best practices information, see the Regulatory Compliance Homepage at www.Dell.com/regulatory_compliance
CAUTION: Many repairs may only be done by a certied service technician. You should only perform troubleshooting and simple
repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an
unpainted metal surface at the same time as touching a connector on the back of the computer.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its
edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have
connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the
cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a
cable, ensure that both connectors are correctly oriented and aligned.
NOTE: The color of your computer and certain components may appear dierently than shown in this document.
Turning o your computer — Windows 10
CAUTION: To avoid losing data, save and close all open les and exit all open programs before you turn o your computer or
remove the side cover.
1 Click or tap .
2 Click or tap and then click or tap Shut down.
NOTE: Ensure that the computer and all attached devices are turned o. If your computer and attached devices did not
automatically turn o when you shut down your operating system, press and hold the power button for about 6 seconds to
turn them o.
Before working inside your computer
1 Ensure that your work surface is at and clean to prevent the computer cover from being scratched.
2 Turn o your computer.
3 If the computer is connected to a docking device (docked), undock it.
4 Disconnect all network cables from the computer (if available).
1
6 Working on your computer
CAUTION: If your computer has an RJ45 port, disconnect the network cable by rst unplugging the cable from your
computer.
5 Disconnect your computer and all attached devices from their electrical outlets.
6 Open the display.
7 Press and hold the power button for few seconds, to ground the system board.
CAUTION: To guard against electrical shock unplug your computer from the electrical outlet before performing Step # 8.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an
unpainted metal surface at the same time as touching a connector on the back of the computer.
8 Remove any installed ExpressCards or Smart Cards from the appropriate slots.
After working inside your computer
After you complete any replacement procedure, ensure that you connect any external devices, cards, and cables before turning on your
computer.
CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries
designed for other Dell computers.
1 Replace the battery.
2 Replace the base cover.
3 Connect any external devices, such as a port replicator or media base, and replace any cards, such as an ExpressCard.
4 Connect any telephone or network cables to your computer.
CAUTION: To connect a network cable, rst plug the cable into the network device and then plug it into the
computer.
5 Connect your computer and all attached devices to their electrical outlets.
6 Turn on your computer.
Working on your computer 7
Technology and components
This chapter details the technology and components available in the system.
Topics:
• Power adapter
• DDR4
• HDMI 1.4- HDMI 2.0
• USB features
• USB Type-C
Power adapter
This laptop is shipped with 7.4mm barrel plug on power adapter.
WARNING: When you disconnect the power adapter cable from the laptop, grasp the connector, not the cable itself, and then
pull rmly but gently to avoid damaging the cable.
WARNING: The power adapter works with electrical outlets worldwide. However, power connectors and power strips vary
among countries. Using an incompatible cable or improperly connecting the cable to the power strip or electrical outlet may
cause re or equipment damage.
DDR4
DDR4 (double data rate fourth generation) memory is a higher-speed successor to the DDR2 and DDR3 technologies and allows up to 512
GB in capacity, compared to the DDR3's maximum of 128 GB per DIMM. DDR4 synchronous dynamic random-access memory is keyed
dierently from both SDRAM and DDR to prevent the user from installing the wrong type of memory into the system.
DDR4 needs 20 percent less or just 1.2 volts, compared to DDR3 which requires 1.5 volts of electrical power to operate. DDR4 also supports
a new, deep power-down mode that allows the host device to go into standby without needing to refresh its memory. Deep power-down
mode is expected to reduce standby power consumption by 40 to 50 percent.
DDR4 Details
There are subtle dierences between DDR3 and DDR4 memory modules, as listed below.
Key notch dierence
The key notch on a DDR4 module is in a dierent location from the key notch on a DDR3 module. Both notches are on the insertion edge
but the notch location on the DDR4 is slightly dierent, to prevent the module from being installed into an incompatible board or platform.
2
8 Technology and components
Figure 1. Notch dierence
Increased thickness
DDR4 modules are slightly thicker than DDR3, to accommodate more signal layers.
Figure 2. Thickness dierence
Curved edge
DDR4 modules feature a curved edge to help with insertion and alleviate stress on the PCB during memory installation.
Figure 3. Curved edge
Memory Errors
Memory errors on the system display the new ON-FLASH-FLASH or ON-FLASH-ON failure code. If all memory fails, the LCD does not
turn on. Troubleshoot for possible memory failure by trying known good memory modules in the memory connectors on the bottom of the
system or under the keyboard, as in some portable systems.
HDMI 1.4- HDMI 2.0
This topic explains the HDMI 1.4 and its features along with the advantages.
HDMI (High-Denition Multimedia Interface) is an industry-supported, uncompressed, all-digital audio/video interface. HDMI provides an
interface between any compatible digital audio/video source, such as a DVD player, or A/V receiver and a compatible digital audio and/or
video monitor, such as a digital TV (DTV). The intended applications for HDMI TVs, and DVD players. The primary advantage is cable
reduction and content protection provisions. HDMI supports standard, enhanced, or high-denition video, plus multichannel digital audio on
a single cable.
NOTE: The HDMI 1.4 will provide 5.1 channel audio support.
Technology and components 9
HDMI 1.4- HDMI 2.0 Features
•HDMI Ethernet Channel - Adds high-speed networking to an HDMI link, allowing users to take full advantage of their IP-enabled
devices without a separate Ethernet cable
•Audio Return Channel - Allows an HDMI-connected TV with a built-in tuner to send audio data "upstream" to a surround audio system,
eliminating the need for a separate audio cable
•3D - Denes input/output protocols for major 3D video formats, paving the way for true 3D gaming and 3D home theater applications
•Content Type - Real-time signaling of content types between display and source devices, enabling a TV to optimize picture settings
based on content type
•Additional Color Spaces - Adds support for additional color models used in digital photography and computer graphics
•4K Support - Enables video resolutions far beyond 1080p, supporting next-generation displays that will rival the Digital Cinema systems
used in many commercial movie theaters
•HDMI Micro Connector - A new, smaller connector for phones and other portable devices, supporting video resolutions up to 1080p
•Automotive Connection System - New cables and connectors for automotive video systems, designed to meet the unique demands of
the motoring environment while delivering true HD quality
Advantages of HDMI
• Quality HDMI transfers uncompressed digital audio and video for the highest, crispest image quality.
• Low -cost HDMI provides the quality and functionality of a digital interface while also supporting uncompressed video formats in a
simple, cost-eective manner
• Audio HDMI supports multiple audio formats from standard stereo to multichannel surround sound
• HDMI combines video and multichannel audio into a single cable, eliminating the cost, complexity, and confusion of multiple cables
currently used in A/V systems
• HDMI supports communication between the video source (such as a DVD player) and the DTV, enabling new functionality
USB features
Universal Serial Bus, or USB, was introduced in 1996. It dramatically simplied the connection between host computers and peripheral
devices like mice, keyboards, external drivers, and printers.
Let's take a quick look on the USB evolution referencing to the table below.
Table 1. USB evolution
Type Data Transfer Rate Category Introduction Year
USB 3.0/USB 3.1 Gen 1 5 Gbps Super Speed 2010
USB 2.0 480 Mbps High Speed 2000
USB 3.1 Gen 2 10 Gbps Super Speed 2013
USB 3.0/USB 3.1 Gen 1 (SuperSpeed USB)
For years, the USB 2.0 has been rmly entrenched as the de facto interface standard in the PC world with about 6 billion devices sold, and
yet the need for more speed grows by ever faster computing hardware and ever greater bandwidth demands. The USB 3.0/USB 3.1 Gen 1
nally has the answer to the consumers' demands with a theoretically 10 times faster than its predecessor. In a nutshell, USB 3.1 Gen 1
features are as follows:
• Higher transfer rates (up to 5 Gbps)
10 Technology and components
• Increased maximum bus power and increased device current draw to better accommodate power-hungry devices
• New power management features
• Full-duplex data transfers and support for new transfer types
• Backward USB 2.0 compatibility
• New connectors and cable
The topics below cover some of the most commonly asked questions regarding USB 3.0/USB 3.1 Gen 1.
Speed
Currently, there are 3 speed modes dened by the latest USB 3.0/USB 3.1 Gen 1 specication. They are Super-Speed, Hi-Speed and Full-
Speed. The new SuperSpeed mode has a transfer rate of 4.8Gbps. While the specication retains Hi-Speed, and Full-Speed USB mode,
commonly known as USB 2.0 and 1.1 respectively, the slower modes still operate at 480Mbps and 12Mbps respectively and are kept to
maintain backward compatibility.
USB 3.0/USB 3.1 Gen 1 achieves the much higher performance by the technical changes below:
• An additional physical bus that is added in parallel with the existing USB 2.0 bus (refer to the picture below).
• USB 2.0 previously had four wires (power, ground, and a pair for dierential data); USB 3.0/USB 3.1 Gen 1 adds four more for two pairs
of dierential signals (receive and transmit) for a combined total of eight connections in the connectors and cabling.
• USB 3.0/USB 3.1 Gen 1 utilizes the bidirectional data interface, rather than USB 2.0's half-duplex arrangement. This gives a 10-fold
increase in theoretical bandwidth.
With today's ever increasing demands placed on data transfers with high-denition video content, terabyte storage devices, high megapixel
count digital cameras etc., USB 2.0 may not be fast enough. Furthermore, no USB 2.0 connection could ever come close to the 480Mbps
theoretical maximum throughput, making data transfer at around 320Mbps (40MB/s) — the actual real-world maximum. Similarly, USB
3.0/USB 3.1 Gen 1 connections will never achieve 4.8Gbps. We will likely see a real-world maximum rate of 400MB/s with overheads. At this
speed, USB 3.0/USB 3.1 Gen 1 is a 10x improvement over USB 2.0.
Applications
USB 3.0/USB 3.1 Gen 1 opens up the laneways and provides more headroom for devices to deliver a better overall experience. Where USB
video was barely tolerable previously (both from a maximum resolution, latency, and video compression perspective), it's easy to imagine
Technology and components 11
that with 5-10 times the bandwidth available, USB video solutions should work that much better. Single-link DVI requires almost 2Gbps
throughput. Where 480Mbps was limiting, 5Gbps is more than promising. With its promised 4.8Gbps speed, the standard will nd its way
into some products that previously weren't USB territory, like external RAID storage systems.
Listed below are some of the available SuperSpeed USB 3.0/USB 3.1 Gen 1 products:
• External Desktop USB 3.0/USB 3.1 Gen 1 Hard Drives
• Portable USB 3.0/USB 3.1 Gen 1 Hard Drives
• USB 3.0/USB 3.1 Gen 1 Drive Docks & Adapters
• USB 3.0/USB 3.1 Gen 1 Flash Drives & Readers
• USB 3.0/USB 3.1 Gen 1 Solid-state Drives
• USB 3.0/USB 3.1 Gen 1 RAIDs
• Optical Media Drives
• Multimedia Devices
• Networking
• USB 3.0/USB 3.1 Gen 1 Adapter Cards & Hubs
Compatibility
The good news is that USB 3.0/USB 3.1 Gen 1 has been carefully planned from the start to peacefully co-exist with USB 2.0. First of all,
while USB 3.0/USB 3.1 Gen 1 species new physical connections and thus new cables to take advantage of the higher speed capability of
the new protocol, the connector itself remains the same rectangular shape with the four USB 2.0 contacts in the exact same location as
before. Five new connections to carry receive and transmitted data independently are present on USB 3.0/USB 3.1 Gen 1 cables and only
come into contact when connected to a proper SuperSpeed USB connection.
Windows 8/10 will be bringing native support for USB 3.1 Gen 1 controllers. This is in contrast to previous versions of Windows, which
continue to require separate drivers for USB 3.0/USB 3.1 Gen 1 controllers.
Microsoft announced that Windows 7 would have USB 3.1 Gen 1 support, perhaps not on its immediate release, but in a subsequent Service
Pack or update. It is not out of the question to think that following a successful release of USB 3.0/USB 3.1 Gen 1 support in Windows 7,
SuperSpeed support would trickle down to Vista. Microsoft has conrmed this by stating that most of their partners share the opinion that
Vista should also support USB 3.0/USB 3.1 Gen 1.
Advantages of Displayport over USB Type-C
• Full DisplayPort audio/video (A/V) performance (up to 4K at 60Hz)
• SuperSpeed USB (USB 3.1) data
• Reversible plug orientation and cable direction
• Backwards compatibility to VGA, DVI with adaptors
• Supports HDMI 2.0a and is backwards compatible with previous versions
USB Type-C
USB Type-C is a new, tiny physical connector. The connector itself can support various exciting new USB standard like USB 3.1 and USB
power delivery (USB PD).
Alternate Mode
USB Type-C is a new connector standard that's very small. It's about a third the size of an old USB Type-A plug. This is a single connector
standard that every device should be able to use. USB Type-C ports can support a variety of dierent protocols using “alternate modes,”
which allows you to have adapters that can output HDMI, VGA, DisplayPort, or other types of connections from that single USB port
12 Technology and components
USB Power Delivery
The USB PD specication is also closely intertwined with USB Type-C. Currently, smartphones, tablets, and other mobile devices often use
a USB connection to charge. A USB 2.0 connection provides up to 2.5 watts of power — that'll charge your phone, but that's about it. A
laptop might require up to 60 watts, for example. The USB Power Delivery specication ups this power delivery to 100 watts. It's bi-
directional, so a device can either send or receive power. And this power can be transferred at the same time the device is transmitting
data across the connection.
This could spell the end of all those proprietary laptop charging cables, with everything charging via a standard USB connection. You could
charge your laptop from one of those portable battery packs you charge your smartphones and other portable devices from today. You
could plug your laptop into an external display connected to a power cable, and that external display would charge your laptop as you used
it as an external display — all via the one little USB Type-C connection. To use this, the device and the cable have to support USB Power
Delivery. Just having a USB Type-C connection doesn't necessarily mean they do.
USB Type-C and USB 3.1
USB 3.1 is a new USB standard. USB 3's theoretical bandwidth is 5 Gbps, while USB 3.1 Gen2 is10Gbps . That's double the bandwidth, as
fast as a rst-generation Thunderbolt connector. USB Type-C isn't the same thing as USB 3.1. USB Type-C is just a connector shape, and
the underlying technology could just be USB 2 or USB 3.0. In fact, Nokia's N1 Android tablet uses a USB Type-C connector, but underneath
it's all USB 2.0 — not even USB 3.0. However, these technologies are closely related.
Technology and components 13
Disassembly and reassembly
Subscriber Identity Module(SIM) board
Installing the Subscriber Identication Module card
1 Insert Subscriber Identication Module (SIM) card removal tool or a paperclip into the pinhole [1].
2 Pull the SIM card tray to remove it [2].
3 Place the SIM on the SIM card tray.
4 Push the SIM card tray into the slot until it clicks into place.
Removing the Subscriber Identication Module card
CAUTION: Removing the Subscriber Identication Module (SIM) card when the computer is on may cause data loss or damage
the card. Ensure your computer is turned o or the network connections are disabled.
1 Insert a paperclip or a SIM card removal tool into the pinhole on the SIM card tray.
2 Pull the SIM card tray to remove it.
3 Remove the SIM card from the SIM card tray.
4 Push the SIM card tray into the slot until it clicks into place.
3
14 Disassembly and reassembly
Base cover
Removing the base cover
1 Follow the procedure in Before working inside your computer.
2 To remove the base cover:
a Loosen the M2.5x5 (8) captive screws that secure the base cover to the [1].
b Pry the base cover from the edge near the air vent [2].
NOTE: a plastic scribe to pry the recess, starting from the top edge of the base cove.
3 Lift the base cover away from the laptop.
Disassembly and reassembly 15
Installing the base cover
1 Align the base cover with the screw holders on the laptop .
2 Press the edges of the cover until it clicks into place.
3 Tighten the M2x5 screws to secure the base cover to the laptop.
4 Follow the procedure in After working inside your computer.
Battery
Removing the battery
NOTE: A 6-cell 92WHr battery has 2 screws.
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 To remove the battery:
a Disconnect the battery cable from the connector on the system board [1].
b Loosen the M2.5x5 captive screw 2 that secures the battery to the laptop [2].
c Lift the battery away from the laptop chassis [3].
16 Disassembly and reassembly
Installing the battery
NOTE: the 92Whr battery requires the use of a M.2 card and a 68Whr battery can be used with either a M.2 or 7mm SATA drive.
1 Insert the battery into the slot on the laptop.
NOTE: Route the battery cable below the battery routing channels to enable proper connection to the connector.
2 Connect the battery cable to the connector on the system board.
3 Tighten the M2.5x5 screw (2) to secure the battery to the laptop.
4 Install the base cover.
5 Follow the procedure in After working inside your computer.
Solid State Drive — optional
Removing the M.2 Solid State Drive - SSD
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
3 To remove the SSD:
a Remove the one M2x3 screw [1] that secures the SSD bracket to the laptop and lift the SSD frame [2] that secures the SSD
card to the system board. .
b the SSD that secures the SSD card to the system board .
Disassembly and reassembly 17
c Lift and pull the SSD card from the laptop [3].
NOTE: For models shipped with NVMe SSDs, remove the thermal plate placed over the SSD.
4 To remove the SSD clip:
a Remove the M2x3 screw that secures the SSD clip to the laptop [1].
b Lift the SSD clip away from the laptop [2].
18 Disassembly and reassembly
Installing the M.2 Solid State Drive - SSD
NOTE: Before installing SSD card, ensure that the battery is fully charged or the power cable is plugged in.
1 Place the SSD clip on the laptop.
NOTE: Ensure to place the SSD clip head in the placeholder in the system chassis.
2 Tighten the M2x3 screw that secures SSD clip to the laptop.
3 Insert the SSD into the socket on the laptop.
4 Place the SSD bracket and tighten the M2x3 screw to secure the SSD to the laptop.
5 Install the:
abattery
bbase cover
6 Follow the procedure in After working inside your computer.
WLAN card
Removing the WLAN card
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
Disassembly and reassembly 19
bbattery
3 To remove the WLAN card:
a Remove the M2x3 screw (1) that secures the WLAN card to the laptop [1].
b Lift the metal bracket that secures the WLAN cables to the WLAN card [2].
c Disconnect the WLAN cables from the connectors on the WLAN card [3].
NOTE: The WLAN card is held in place with an adhesive foam spacer. When removing the wireless card from the
system, make sure the adhesive pad stays on the system board/chassis frame during the prying process. If the
adhesive pad is removed from the system along with the wireless card, adhere it back to the system.
d Pull the WLAN card to release it from the connector on the system board[4].
NOTE: Ensure NOT to pull the WLAN card more than 35°, to avoid pin damage.
Installing the WLAN card
1 Insert the WLAN card into the slot on the laptop.
2 Route the WLAN cables through the routing channel.
NOTE: When installing the display assembly or chassis frame onto the system, the wireless and WLAN antennas must be
routed correctly into the routing channels on the chassis frame.
3 Connect the WLAN cables to the connectors on the WLAN Card.
4 Place the metal bracket and tighten the M2x3 screw to secures the WLAN card to the system board.
5 Install the:
abattery
bbase cover
20 Disassembly and reassembly
6 Follow the procedure in After working inside your system.
WWAN card
Removing the WWAN card
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
3 To remove the WWAN card:
a Disconnect the WWAN cables from the connectors on the WWAN card [1].
NOTE: The WWAN card is held in place with an adhesive foam spacer. When removing the wireless card from the
system, make sure the adhesive pad stays on the system board/chassis frame during the prying process. If the
adhesive pad is removed from the system along with the wireless card, adhere it back to the system.
b Remove the M2x3 screw (1) that secures the WWAN card to the system board [2].
c Lift the WWAN card to release it from the connector on the system board [3].
NOTE: Ensure NOT to pull the WWAN card more than 35°, to avoid pin damage.
Disassembly and reassembly 21
Installing the WLAN card
1 Insert the WWAN card into the slot on the laptop.
2 Place the M2x3 screw to secures the WWAN card to the system board.
3 Connect the WWAN cables to the connectors on the WWAN Card.
4 Install the:
abattery
bbase cover
5 Follow the procedure in After working inside your system.
Coin-cell battery
Removing the coin cell battery
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
3 To remove the coin cell battery:
a Disconnect the coin cell battery cable from the connector on the system board [1].
b Pry the coin cell battery to release from the adhesive and lift it away from the system board [2].
22 Disassembly and reassembly
Installing the coin cell battery
1 Place the coin cell battery on the system board.
2 Connect the coin cell battery cable to the connector on the system board.
NOTE: Route the coin cell battery cable carefully to avoid damaging the cable.
3 Install the:
achassis frame
bbattery
cbase cover
4 Follow the procedure in After working inside your computer.
Memory modules
Removing the memory module
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
3 To remove the memory module:
a Press the clips securing the memory module until the memory pops-up [1].
b Pull the memory module from the connector on the system board [2].
Disassembly and reassembly 23
Installing the memory module
1 Insert the memory module into the memory module socket then press downward until the clips secure the memory module.
NOTE: Ensure to insert the memory module at an angle NOT more than 30°. Press the memory module down to engage the
retaining clips.
2 Install the:
abattery
bbase cover
3 Follow the procedures in After working inside your computer.
Keyboard
Removing keyboard lattice
1 Follow the procedure in Before working inside your computer.
2 Pry the keyboard lattice from one of the recess points [1] and lift the lattice from the system [2].
NOTE: Gently pull or lift keyboard lattice in clockwise or anticlockwise direction to avoid breakage.
NOTE: Use a plastic scribe to pry the keyboard lattice from the pry points and move around the lattice for removal.
24 Disassembly and reassembly
Removing the keyboard
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
ckeyboard lattice
3 To remove the keyboard:
a Lift the latch and disconnect the keyboard cable from the connector on the system.
b Lift the latch and disconnect the keyboard backlight cable from the connector on the system [2].
NOTE: Number of cables to disconnect is based on the keyboard type.
c Lift the latch and disconnect the cable from the connector on the system board [3].
d Lift the latch and disconnect the cable from the connector on the system board [4].
e Turn over the system and open the laptop in front view mode.
f Remove the M2 x 2.5 (6) screws that secure the keyboard to the system [1].
g Flip the keyboard from the bottom and lift it from the system along with the keyboard cable and the keyboard back light cable
[2].
WARNING: Gently pull the keyboard cable and the keyboard back light cable routed beneath the chassis frame to
avoid damaging the cables.
Disassembly and reassembly 25
26 Disassembly and reassembly
Installing the keyboard
1 Hold the keyboard and route the keyboard cable and the keyboard backlight cables through the palmrest in the system.
2 Align the keyboard with the screw holders on the system.
3 Replace the M2x2.5 screws (6) to secure the keyboard to the system.
4 Turn the system over and connect the keyboard cable and the keyboard backlight cable to the connector in the system.
NOTE: When reinstalling the chassis frame ensure the keyboard cables are NOT under the lattice , but run through the
opening in the frame before connecting them to system board.
5 Install the:
akeyboard lattice
bbattery
cbase cover
6 Follow the procedure in After working inside your computer.
Installing the keyboard trim
1 Align the keyboard trim with the tabs on the computer and press the keyboard until the keyboard clicks into place.
2 Follow the procedure in After working inside your system.
Heat sink
Removing the heat sink
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
3 To remove the heat sink - :
a Disconnect the heat sink assembly cable and remove the screws (2) that secure on the system board[1, 2]. .
NOTE: Remove the screws that secure the heat sink .
Disassembly and reassembly 27
b Remove the M2x3 screws (6) that secures the heat sink assembly to the system board [1].
c Lift the heat sink assembly away from the system board [2].
28 Disassembly and reassembly
Installing the heat sink
1 Place the heat sink assembly on the system board and align the heat sink with the screw holders.
2 Tighten the M2x3 screws 8 to secure the heat sink assembly to the system board.
3 Connect the heat sink assembly to the connector on the system board.
4 Install the:
abattery
bbase cover
5 Follow the procedure in After working inside your computer.
Power connector port
Removing the power connector port
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
3 To remove the power connector port:
a Disconnect the power connector port cable from the connector on the system board [1].
NOTE: Use a plastic scribe to release the cable from the connector. Do not pull the cable as it may result in breakage.
b Remove the M2x3 screw to release the metal bracket that secures the power connector port [2].
c Remove the metal bracket that secures the power connector port [3].
d Lift the power connector port away from the laptop [4].
Disassembly and reassembly 29
Installing the power connector port
1 Insert the power connector port into the slot on the laptop.
2 Place the metal bracket on the power connector port.
3 Tighten the M2x3 screw to secure the metal bracket to the power connector port on the laptop.
4 Connect the power connector port cable to the connector on the system board.
5 Install the:
abattery
bbase cover
6 Follow the procedure in After working inside your computer.
Chassis frame
Removing the chassis frame
1 Follow the procedure in Before working inside your computer.
2 Remove the:
aSIM card module
bbase cover
cbattery
dWLAN card
eWWAN card
30 Disassembly and reassembly
fSSD card
3 To release the chassis frame:
a Release the WLAN and WWAN cables from the routing channels [1].
b Disconnect the speaker cable from the connector on the system board [2].
c Lift the latch to disconnect the backlight cable (optional) [3], touchpad cable [4], pointstick cable [5], and keyboard cable [6]
from the connector on the system board.
4 To remove the chassis frame:
a Remove the M2x3 (5), M2x5 (2) screws that secure the chassis frame to the laptop[1].
b Lift the chassis frame away from the laptop [2].
Disassembly and reassembly 31
Installing the chassis frame
1 Place the chassis frame on the computer and tighten the screws M2x5 (2), M2x3 (5).
NOTE: When reinstalling the chassis frame ensure the keyboard cables are NOT under the frame, but run through the
opening in the frame.
2 Connect the speaker, keyboard cable, touchpad cable, pointstick cable and backlight cable(optional).
3 Route the WLAN and WWAN cable.
NOTE: Ensure the coin cell battery cable is properly routed in between the chassis frame and the system board to avoid
damages to the cable.
4 Install the:
aSSD card
bWWAN card
cWLAN card
dbattery
ebase cover
fSIM card module
5 Follow the procedure in After working inside your system.
System board
Removing the system board
1 Follow the procedure in Before working inside your computer.
2 Remove the:
aSIM card module
32 Disassembly and reassembly
bbase cover
cbattery
dWLAN card
eWWAN card
fSSD card
gmemory module
hheat sink
icoin cell battery
jPower connector port
kchassis frame
3 To release the system board:
a Remove the M2x5 screws that secures the metal bracket to the system board [1].
b Lift the metal bracket that secures the display cable to the system board [ 2].
c Disconnect the display cable from the connectors on the system board [3].
4 To remove the system board:
a Lift the latch and disconnect the LED board, mother board and touchpad cable from the connectors on the system board [1].
b Remove the M2x5 screws (2) that secure the metal USB-C port bracket to the system board and lift the bracket away from the
system board [2,3].
NOTE: The metal bracket referred is the USB-C port bracket.
Disassembly and reassembly 33
5 Remove the M2x3 screws (3) and lift the system board away from the computer [1, 2].
34 Disassembly and reassembly
Installing the system board
1 Align the system board with the screw holders on the laptop.
2 Tighten the M2x3 screws to secure the system board to the laptop.
3 Place the metal USB-C bracket and tighten the M2x5 screws on the system board.
4 Connect the LED, mother board and touchpad cable to the system board.
5 Connect the display cable on the system board.
6 Place the eDP cable and metal bracket to system board and tighten the M2x3 screws to secure to the system board.
7 Install the:
achassis frame
bPower connector port
ccoin cell battery
dheat sink
ememory module
fSSD card
gWWAN card
hWLAN card
ibattery
jbase cover
kSIM card module
8 Follow the procedure in After working inside your computer.
Touchpad
Removing the touchpad
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
cWLAN card
dWWAN card
eSSD card
fchassis frame
3 To release the touchpad panel:
a Lift the latch and disconnect the SmartCard reader cable from the connector on the system board [1].
b Peel o the SmartCard reader cable from the adhesive [2].
Disassembly and reassembly 35
4 To remove the touchpad panel:
a Lift the latch and disconnect the touchpad panel cable from the connector on the system board [1].
b Remove the M2x3 screws (2) that secure the touchpad panel to the laptop [2].
c Lift the touchpad panel away from the laptop [3].
36 Disassembly and reassembly
Installing the touchpad
1 Insert the bottom edge of the Button Board under the plastic holder tabs rst when placing the buttons board back into the chassis.
2 Tighten the M2x3 screws to secure the touchpad panel.
3 Connect the touchpad cable.
4 Connect the SmartCard reader cable to the laptop.
5 Install the:
achassis frame
bSSD card
cWWAN card
dWLAN card
ebattery
fbase cover
6 Follow the procedure in After working inside your computer.
SmartCard module
Removing the SmartCard reader
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
Disassembly and reassembly 37
bbattery
cWLAN card
dWWAN card
eSSD card
fchassis frame
3 To release the SmartCard reader:
a Disconnect the SmartCard reader board cable from the connector on the system board [1].
b Peel o the cable to release from the adhesive [2].
4 To remove the SmartCard reader:
a Remove the M2x3 screws (2) that secure the SmartCard reader board to the palmrest [1].
b Pull the SmartCard reader board to release on the system board [2].
38 Disassembly and reassembly
Installing the SmartCard reader
1 Place the SmartCard reader on the laptop.
2 Tighten the M2x3 screws to secure the SmartCard reader to the laptop.
3 Ax the SmartCard reader cable and connect the cable to the connector on the system board.
4 Install the:
achassis frame
bSSD card
cWWAN card
dWLAN card
ebattery
fbase cover
5 Follow the procedure in After working inside your computer.
LED board
Removing the LED board
1 Follow the procedure in Before working inside your computer.
2 Remove the:
Disassembly and reassembly 39
abase cover
bbattery
cWLAN card
dWWAN card
eSSD card
fchassis frame
3 To remove the LED board:
a Lift the latch and disconnect the LED board cable from the connector on the LED board [1].
b Remove the M2x3 screw that secures the LED board to the laptop [2].
c Lift the LED board away from the laptop [3].
Installing the LED board
1 Place the LED board on the laptop.
2 Tighten the M2x3 screw to secure the LED board to the laptop.
3 Connect the LED board cable to the connector on the LED board.
4 Install the:
achassis frame
bSSD card
cWWAN card
dWLAN card
ebattery
fbase cover
5 Follow the procedure in After working inside your computer.
40 Disassembly and reassembly
Speaker
Removing the speaker
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
cWLAN card
dWWAN card
eSSD card
fchassis frame
3 To disconnect the cables:
a Lift the latch and disconnect the LED board cable [1].
b Disconnect and unroute the speaker cable [2].
c Remove the speaker cable from the routing clips [3].
4 Lift the speakers from the laptop.
NOTE: Speaker are xed to the laptop in the speaker holder, lift the speaker gently to avoid damage to the
holders.
Disassembly and reassembly 41
Installing the speaker
1 Place the speakers into the slots on the laptop.
2 Route the speaker cable through the retention clips through the routing channel.
3 Connect the speaker and LED board cable to the laptop.
4 Install the:
achassis frame
bSSD card
cWLAN card
dbattery
ebase cover
5 Follow the procedure in After working inside your computer.
Hinge cap
Removing the hinge cap
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
3 To remove the hinge cap:
a Remove the M2x3 screws that secure the hinge cap to the laptop [1].
b Remove the hinge cap from the laptop [2].
42 Disassembly and reassembly
Installing the hinge cap
1 Place the hinge bracket to align with the screw holders on the laptop.
2 Tighten the M2x3 screws to secure the display assembly to the laptop.
3 Install the:
abattery
bbase cover
4 Follow the procedure in After working inside your computer.
Display assembly
Removing the display assembly
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
cWWAN card
dWLAN card
ehinge cap
3 To disconnect the display cable:
a Release the WLAN cable from the routing channels [1].
Disassembly and reassembly 43
b Remove the M2x3 screws (2) and lift the metal bracket that secure the display cable on the computer [2,3].
c Disconnect the display cable [4].
4 To remove hinge screws:
a Remove the M2x5 screws (4) that secure the display assembly to the system board [1].
b Release the antenna cables and display cable from the routing channel [2, 3].
5 Turn over the laptop.
6 To remove the display assembly:
a Remove the M2x5 screws (2) that secure the display assembly to the laptop [1].
b Flip to open the display [2].
44 Disassembly and reassembly
7 Slide the display assembly away from the system base.
Disassembly and reassembly 45
Installing the display assembly
1 Place the display assembly to align with the screw holders on the laptop.
NOTE: Close the LCD before inserting the screws or turning over the laptop.
CAUTION: Route the display cable and the antenna cable through the LCD hinge mount holes as LCD assembly is inserted
into the base, to prevent possible cable damage.
2 Tighten the M2x5 screws to secure the display assembly to the laptop.
3 Turn over the laptop.
4 Connect the antenna cables and display cable to the connectors.
5 Place the display cable bracket over the connector and tighten the M2x5 screws to secure the display cable to the laptop.
6 Install the:
ahinge cap
bWLAN card
cbattery
dbase cover
7 Follow the procedure in After working inside your computer.
Display bezel
Removing display bezel
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
cWLAN card
dWWAN card
edisplay assembly
3 To remove the display bezel:
a Pry the display bezel at the base of the display [1].
NOTE: When removing or reinstalling the display bezel from the display assembly, technicians should note that the
display bezel is secured to the LCD panel with a strong adhesive and care must be taken to avoid damage to LCD.
b Lift the display bezel to release it [2].
c Pry the edges on the side of the display to release the display bezel [3, 4,5].
CAUTION: The adhesive used on the LCD bezel to seal it with the LCD itself, makes it hard to remove the bezel as the
adhesive is very strong and tends to stay stuck to the LCD portion and can peel the layers up or crack the glass when
trying to pry the two items apart.
46 Disassembly and reassembly
Installing display bezel
1 Place the display bezel on the display assembly.
NOTE: Remove the protective covering on the adhesive on the LCD bezel before placing on the display assembly.
2 Starting from a top corner, press clockwise on the display bezel and work around the entire bezel until it clicks on to the display
assembly.
3 Install the:
adisplay assembly
bWWAN card
cWLAN card
dbattery
ebase cover
4 Follow the procedure in After working inside your computer.
Display hinges
Removing the display hinge
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
cWWAN card
dWLAN card
ehinge cap
Disassembly and reassembly 47
fdisplay assembly
gdisplay bezel
3 To remove the display hinge:
a Remove the M2.5x3.5 screws that secure the display hinge to the display assembly [1].
b Lift the display hinge away from the display assembly [2].
c Repeat the to remove the other display hinge.
Installing the display hinge
1 Place the display hinge cover on the display assembly.
2 Tighten the M2.5x3.5 screw to secure the display hinge cover to the display assembly.
3 Repeat the same procedure step 1-2 to install the other display hinge cover.
4 Install the:
adisplay bezel
bdisplay assembly
chinge cap
dWWAN card
eWLAN card
fbattery
gbase cover
5 Follow the procedure in After working inside your computer.
48 Disassembly and reassembly
Display panel
Removing the display panel
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
cWWAN card
dWLAN card
ehinge cap
fdisplay assembly
gdisplay bezel
3 Remove the M2x3 screws (4) that secure the display panel to the display assembly [1] and lift to turn over the display panel to access
the eDP cable [2].
4 To remove the display panel:
a Peel o the adhesive tape [1].
b Lift the blue tape that secures the display cable [2].
c Lift the latch to disconnect the display cable from the connector on the display panel [3, 4].
Disassembly and reassembly 49
Installing the display panel
1 Connect the eDP cable to the connector and ax the blue tape.
2 Ax the adhesive tape to secure the eDP cable.
3 Replace the display panel to align with the screw holders on the display assembly.
4 Tighten the M2x3 screws to secure the display panel to the display assembly.
5 Install the:
adisplay bezel
bdisplay assembly
chinge cap
dWWAN card
eWLAN card
fbattery
gbase cover
6 Follow the procedure in After working inside your computer.
50 Disassembly and reassembly
Display (eDP) cable
Removing the eDP cable
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
cWWAN card
dWLAN card
edisplay assembly
fDisplay Panel
gdisplay bezel
3 Peel o the eDP cable from the adhesive to remove it from the display.
Installing the eDP cable
1 Ax the eDP cable on the display assembly.
2 Install the:
adisplay panel
bdisplay bezel
cdisplay assembly
dhinge cap
eWWAN card
fWLAN card
gbattery
hbase cover
Disassembly and reassembly 51
3 Follow the procedure in After working inside your computer.
Camera
Removing camera
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
cWLAN
dWWAN card
edisplay assembly
fdisplay bezel
gdisplay panel
3 To remove the camera:
a Disconnect the camera cable from the connector on the display panel[1].
b Carefully pry and lift the camera module from the display back cover [2].
52 Disassembly and reassembly
Installing camera
1 Insert the camera into the slot on the display back cover.
2 Connect the display cable to the connector.
3 Connect the camera cable to the connector on the camera module.
4 Install the :
adisplay panel
bdisplay bezel
cdisplay assembly
dWLAN
eWWAN card
fmemory module
gbattery
hbase cover
5 Follow the procedure in After working inside your computer.
Display back cover assembly
Removing the display back cover assembly
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
cWWAN card
dWLAN card
edisplay assembly
fdisplay bezel
gdisplay panel
heDP cable
icamera
3 The display back cover assembly is the remaining component, after removing all the components.
Disassembly and reassembly 53
Installing the display back cover assembly
1 The display back cover assembly is the remaining component, after removing all the components.
2 Install the:
acamera
beDP cable
cdisplay panel
ddisplay bezel
edisplay assembly
fWWAN card
gWLAN card
hbattery
ibase cover
3 Follow the procedure in After working inside your computer.
Palm rest
Replacing the palm rest
1 Follow the procedure in Before working inside your computer.
2 Remove the:
abase cover
bbattery
ckeyboard
dWLAN card
eWWAN card
fSSD card
gmemory module
hTouchpad
iheat sink
jcoin cell battery
kchassis frame
lsystem board
mhinge cap
ndisplay assembly
NOTE: The component you are left with is the palm rest.
54 Disassembly and reassembly
3 Install the following components on the new palm rest.
adisplay assembly
bhinge cap
csystem board
dchassis frame
ecoin cell battery
fheat sink
gTouchpad
hmemory module
iSSD card
jWWAN card
kWLAN card
lkeyboard
mbattery
nbase cover
4 Follow the procedure in After working inside your computer.
Disassembly and reassembly 55
Troubleshooting
Enhanced Pre-Boot System Assessment — ePSA
diagnostics
The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware. The ePSA is embedded with the
BIOS and is launched by the BIOS internally. The embedded system diagnostics provides a set of options for particular devices or device
groups allowing you to:
• Run tests automatically or in an interactive mode
• Repeat tests
• Display or save test results
• Run thorough tests to introduce additional test options to provide extra information about the failed device(s)
• View status messages that inform you if tests are completed successfully
• View error messages that inform you of problems encountered during testing
CAUTION: Use the system diagnostics to test only your computer. Using this program with other computers may cause invalid
results or error messages.
NOTE: Some tests for specic devices require user interaction. Always ensure that you are present at the computer terminal
when the diagnostic tests are performed.
Running the ePSA Diagnostics
1 Invoke diagnostics boot by either of the methods suggested above
2 Once on one time boot menu use up/down arrow key to navigate to ePSA or diagnostics and press <return> key to launch
Fn+PWR will ash diagnostics boot selected on screen and launch ePSA/diagnostics directly.
3 On the boot menu screen, select the Diagnostics option.
4 Press the arrow in the lower-right corner to go to the page listing.
The items detected are listed and will be tested
5 If there are any issues, error codes are displayed.
Note the error code and validation number and contact Dell.
To run a diagnostic test on a specic device
1 Press Esc and click Yes to stop the diagnostic test.
2 Select the device from the left pane and click Run Tests.
3 If there are any issues, error codes are displayed.
Note the error code and validation number and contact Dell.
Real Time Clock reset
The Real Time Clock (RTC) reset function allows you to recover your Dell system from No POST/No Boot/No Power situations. To initiate
the RTC reset on the system make sure system is in a power-o state and is connected to power source . Press and hold the power button
for 25 seconds and then release the power button.
4
56 Troubleshooting
NOTE: If AC power is disconnected from the system during the process or the power button is held longer than 40 seconds, the
RTC reset process is aborted.
The RTC reset will reset the BIOS to Defaults, un-provision Intel vPro and reset the system date and time. The following items are
unaected by the RTC reset:
• Service Tag
• Asset Tag
• Ownership Tag
• Admin Password
• System Password
• HDD Password
• Key Databases
• System Logs
The following items may or may not reset based on your custom BIOS setting selections:
• The Boot List
• Enable Legacy OROMs
• Secure Boot Enable
• Allow BIOS Downgrade
Troubleshooting 57
Getting help
Contacting Dell
NOTE: If you do not have an active Internet connection, you can nd contact information on your purchase invoice, packing slip,
bill, or Dell product catalog.
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services
may not be available in your area. To contact Dell for sales, technical support, or customer service issues:
1 Go to Dell.com/support.
2 Select your support category.
3 Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.
4 Select the appropriate service or support link based on your need.
5
58 Getting help