Dell Vostro 15–3558 Owner's Manual
Working on Your Computer
Removing and Installing Components
System Setup
Diagnostics
- Enhanced Pre-Boot System Assessment (ePSA) Diagnostics
Specifications
- Specifications
Contacting Dell
- Contacting Dell

DELL 3558 User Manual

Displayed below is the user manual for 3558 by DELL which is a product in the Notebooks category. This manual has pages.

Related Manuals

DELL 3558 Manual

Dell Vostro 15–3558

Owner's Manual

Regulatory Model: P52F

Regulatory Type: P52F001

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other

jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.

2015 - 03

Rev. A00

Contents

1 Working on Your Computer................................................................................5

Before Working Inside Your Computer................................................................................................ 5

Recommended Tools............................................................................................................................6

Turning Off Your Computer..................................................................................................................6

After Working Inside Your Computer................................................................................................... 7

2 Removing and Installing Components............................................................. 8

Removing the Battery............................................................................................................................8

Installing the Battery..............................................................................................................................9

Removing the Optical-disk Drive..........................................................................................................9

Installing the Optical-disk Drive............................................................................................................9

Removing the Access Panel..................................................................................................................9

Installing the Access Panel..................................................................................................................10

Removing the Hard Drive....................................................................................................................10

Installing the Hard Drive......................................................................................................................12

Removing the Memory Module.......................................................................................................... 12

Installing the Memory Module............................................................................................................ 13

Removing the WLAN Card.................................................................................................................. 13

Installing the WLAN Card.................................................................................................................... 13

Removing the Coin-Cell Battery.........................................................................................................13

Installing the Coin-cell battery........................................................................................................... 14

Removing the Keyboard......................................................................................................................14

Installing the Keyboard........................................................................................................................15

Removing the Base Cover...................................................................................................................15

Installing the Base Cover.....................................................................................................................17

Removing the Input/Output (I/O) Board............................................................................................ 17

Installing the Input/Output (I/O) Board.............................................................................................. 18

Removing the Heatsink Assembly.......................................................................................................19

Installing the Heatsink Assembly........................................................................................................20

Removing the Speakers...................................................................................................................... 20

Installing the Speakers.........................................................................................................................21

Removing the System Board...............................................................................................................21

Installing the System Board................................................................................................................ 23

Removing the Power Connector....................................................................................................... 24

Installing the Power Connector......................................................................................................... 24

Removing the Display Assembly.........................................................................................................25

Installing the Display Assembly...........................................................................................................26

Removing the Display Bezel............................................................................................................... 27

Installing the Display Bezel................................................................................................................. 27

Removing the Camera........................................................................................................................28

Installing the Camera..........................................................................................................................28

Removing the Display Hinges.............................................................................................................29

Installing the Display Hinges...............................................................................................................29

Removing the Display Panel...............................................................................................................30

Installing the Display Panel..................................................................................................................31

3 System Setup....................................................................................................... 33

Boot Sequence....................................................................................................................................33

Navigation Keys................................................................................................................................... 33

System Setup Options.........................................................................................................................34

Updating the BIOS ..............................................................................................................................41

System and Setup Password...............................................................................................................42

Assigning a System Password and Setup Password.................................................................... 42

Deleting or Changing an Existing System and/or Setup Password.............................................43

4 Diagnostics..........................................................................................................44

Enhanced Pre-Boot System Assessment (ePSA) Diagnostics........................................................... 44

5 Specifications...................................................................................................... 45

Specifications...................................................................................................................................... 45

6 Contacting Dell...................................................................................................50

Contacting Dell................................................................................................................................... 50

Working on Your Computer

Before Working Inside Your Computer

Use the following safety guidelines to help protect your computer from potential damage and to help to

ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes

that the following conditions exist:

• You have read the safety information that shipped with your computer.

• A component can be replaced or--if purchased separately--installed by performing the removal

procedure in reverse order.

WARNING: Disconnect all power sources before opening the computer cover or panels. After you

finish working inside the computer, replace all covers, panels, and screws before connecting to

the power source.

WARNING: Before working inside your computer, read the safety information that shipped with

your computer. For additional safety best practices information, see the Regulatory Compliance

Homepage at www.dell.com/regulatory_compliance

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or

by periodically touching an unpainted metal surface, such as a connector on the back of the

computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts

on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a

processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable

itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable,

press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep

them evenly aligned to avoid bending any connector pins. Also, before you connect a cable,

ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear differently than shown in

this document.

To avoid damaging your computer, perform the following steps before you begin working inside the

computer.

1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

2. Turn off your computer (see Turning off Your Computer).

3. If the computer is connected to a docking device (docked), undock it.

CAUTION: To disconnect a network cable, first unplug the cable from your computer and

then unplug the cable from the network device.

4. Disconnect all network cables from the computer.

5. Disconnect your computer and all attached devices from their electrical outlets.

6. Close the display and turn the computer upside-down on a flat work surface.

NOTE: To avoid damaging the system board, you must remove the main battery before you

service the computer.

7. Remove the main battery.

8. Turn the computer top-side up.

9. Open the display.

10. Press the power button to ground the system board.

CAUTION: To guard against electrical shock, always unplug your computer from the

electrical outlet before opening the display.

CAUTION: Before touching anything inside your computer, ground yourself by touching an

unpainted metal surface, such as the metal at the back of the computer. While you work,

periodically touch an unpainted metal surface to dissipate static electricity, which could

harm internal components.

11. Remove any installed ExpressCards or Smart Cards from the appropriate slots.

Recommended Tools

The procedures in this document may require the following tools:

• Small flat-blade screwdriver

• #0 Phillips screwdriver

• #1 Phillips screwdriver

• Small plastic scribe

Turning Off Your Computer

CAUTION: To avoid losing data, save and close all open files and exit all open programs before

you turn off your computer.

1. Shut down the operating system:

• In Windows 8:

– Using a touch-enabled device:

a. Swipe in from the right edge of the screen, opening the Charms menu and select

Settings.

b. Select the and then select Shut down

– Using a mouse:

a. Point to upper-right corner of the screen and click Settings.

b. Click the and select Shut down.

• In Windows 7:

1. Click Start .

2. Click Shut Down.

1. Click Start .

2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click

Shut Down..

2. Ensure that the computer and all attached devices are turned off. If your computer and attached

devices did not automatically turn off when you shut down your operating system, press and hold

the power button for about 4 seconds to turn them off.

After Working Inside Your Computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and

cables before turning on your computer.

CAUTION: To avoid damage to the computer, use only the battery designed for this particular

Dell computer. Do not use batteries designed for other Dell computers.

1. Connect any external devices, such as a port replicator or media base, and replace any cards, such as

an ExpressCard.

2. Connect any telephone or network cables to your computer.

CAUTION: To connect a network cable, first plug the cable into the network device and then

plug it into the computer.

3. Replace the battery.

4. Connect your computer and all attached devices to their electrical outlets.

5. Turn on your computer.

Removing and Installing Components

This section provides detailed information on how to remove or install the components from your

computer.

Removing the Battery

1. Follow the procedures in Before Working Inside Your Computer.

2. Slide the release latch outwards to unlock the battery.

3. Remove the battery from the computer.

Installing the Battery

1. Insert the battery into its slot until it clicks into place.

2. Follow the procedures in After Working Inside Your computer .

Removing the Optical-disk Drive

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the battery.

3. Perform the following steps as shown in the illustration:

a. Remove the screw that secures the optical-disk drive (ODD) to the computer [1].

b. Press on the tab indicated using a scribe [2].

c. Slide the ODD out of the computer [3].

Installing the Optical-disk Drive

1. Insert the ODD into its slot until it clicks into place.

2. Tighten the screw to secure the ODD.

3. Install the battery.

4. Follow the procedures in After Working Inside Your computer .

Removing the Access Panel

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove battery.

3. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the access panel to the computer [1].

b. Lift the access panel partially at a 45–degree angle [2].

4. Remove the access panel from the computer.

Installing the Access Panel

1. Place the access panel to align with the screw holes at the back of the computer.

2. Tighten the screws to secure the access panel to the computer.

3. Install the battery.

4. Follow the procedures in After Working Inside Your computer .

Removing the Hard Drive

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. access panel

3. Perform the following steps as shown in the illustration:

a. Disconnect the hard drive cable from the system board and lift it up to remove it from the

computer [1,2].

b. Remove the screws that secure the hard drive to the computer [3].

4. Perform the following steps as shown in the illustration:

a. Lift the hard drive to remove it from the computer [1,2].

5. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the hard drive to the bracket [1].

b. Lift the hard drive from the bracket [2].

Installing the Hard Drive

1. Place the hard drive in the bracket.

2. Tighten the screws that secure the hard drive to the bracket.

3. Slide the hard drive into the connector.

4. Tighten the screw to secure it to the chassis.

5. Install:

a. access panel

b. battery

6. Follow the procedures in After Working Inside Your computer .

Removing the Memory Module

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. access panel

3. Pry the securing clips away from the memory module until it pops up.

4. Remove the memory module from its socket on the system board.

Installing the Memory Module

1. Insert the memory module into the socket and press to lock the securing clips.

2. Install:

a. access panel

b. battery

3. Follow the procedures in After Working Inside Your computer .

Removing the WLAN Card

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. access panel

3. Perform the following steps as shown in the illustration:

a. Remove the screw that secures the WLAN card to the system board [1,2].

b. Remove the two connectors that secure the WLAN card to the system board [3].

c. Remove the WLAN card from its socket [4].

Installing the WLAN Card

1. Insert the WLAN card into its slot and tighten the screw to secure it to the system board.

2. Connect the two connectors (black cable to the black triangle and white cable to the white triangle).

3. Install:

a. access panel

b. battery

4. Follow the procedures in After Working Inside Your computer

Removing the Coin-Cell Battery

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. access panel

3. Push the coin-cell release latch using a scribe and then pull the coin-cell battery to remove it from

the computer.

Installing the Coin-cell battery

1. Insert the coin-cell battery and press to lock it.

2. Install:

a. access panel

b. battery

3. Follow the procedures in After Working Inside Your computer .

Removing the Keyboard

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the battery.

3. Release the keyboard by prying on the keyboard release tabs using a scribe.

4. Perform the following steps as shown in the illustration:

a. Slide and lift the keyboard to access the keyboard connector cable underneath [1,2].

5. Perform the following steps as shown in the illustration:

a. Disconnect the keyboard cable from the system board [1].

b. Lift the keyboard cable to remove it from the computer [2].

Installing the Keyboard

1. Connect the keyboard cable to the connector on the system board.

2. Slide the keyboard into the retention slots.

3. Press along the top edges to lock the keyboard in place.

4. Install the battery.

5. Follow the procedures in After Working Inside Your computer .

Removing the Base Cover

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. hard drive

c. access panel

d. optical-disk drive

e. WLAN card

f. memory module

g. keyboard

3. Perform the following steps as shown in the illustration:

a. Disconnect the ODD connector and lift it to remove it from the system board [1,2].

b. Remove the screws from inside the palmrest [3].

4. Perform the following steps as shown in the illustration:

a. Disconnect the speaker cable that secures the back cover to the computer [1].

b. Remove the screws that secure the base cover to the computer [2].

5. Perform the following steps as shown in the illustration:

a. Turn the computer over and remove the screws at the base of the computer [1].

b. Release the tabs that secure the base cover [2].

c. Pry up the base cover and slide it away from the computer [3].

Installing the Base Cover

1. Place the base cover on the chassis and press the notches until they lock in place.

2. Connect the ODD connector to the system board.

3. Tighten the screws to secure the base cover to the palmrest.

4. Turn the computer over and tighten the screws at the base of the computer.

5. Install:

a. keyboard

b. memory module

c. hard drive

d. WLAN card

e. access panel

f. optical-disk drive

g. battery

6. Follow the procedures in After Working Inside Your computer .

Removing the Input/Output (I/O) Board

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. optical-disk drive

c. access panel

d. hard drive

e. memory module

f. keyboard

g. base cover

3. Perform the following steps as shown in the illustration:

a. Remove the screw that secures the I/O board [1].

b. Lift the I/O board away from the computer [2].

4. Perform the following steps as shown in the illustration:

a. Disconnect the I/O board cable and lift it away from the computer [1,2].

Installing the Input/Output (I/O) Board

1. Connect the I/O board cable to the system board.

2. Install the I/O board into the chassis.

3. Install:

a. base cover

b. keyboard

c. memory module

d. hard drive

e. WLAN card

f. access panel

g. optical-disk drive

h. battery

4. Follow the procedures in After Working Inside Your computer .

Removing the Heatsink Assembly

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. optical-disk drive

c. access panel

d. hard drive

e. memory module

f. keyboard

g. base cover

3. Perform the following steps as shown in the illustration:

a. Disconnect the system fan cable from the system board [1].

b. Remove the screws that secure the heatsink assembly to the system board.

4. Remove the heatsink assembly from the system board.

Installing the Heatsink Assembly

1. Install the heatsink assembly and tighten the screws to secure it to the system board.

2. Connect the system fan cable to the system board.

3. Install:

a. base cover

b. keyboard

c. memory module

d. hard drive

e. WLAN card

f. access panel

g. optical-disk drive

h. battery

4. Follow the procedures in After Working Inside Your computer .

Removing the Speakers

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. optical-disk drive

c. access panel

d. hard drive

e. memory module

f. keyboard

g. base cover

3. Release the speaker cables from the retention tabs.

4. Lift and remove the speakers from the chassis.

Installing the Speakers

1. Insert the speakers into the chassis and press along the retention clips to lock in place.

2. Install:

a. base cover

b. keyboard

c. memory module

d. hard drive

e. WLAN card

f. access panel

g. optical-disk drive

h. battery

3. Follow the procedures in After Working Inside Your computer.

Removing the System Board

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. optical-disk drive

c. access panel

d. hard drive

e. WLAN card

f. memory module

g. keyboard

h. base cover

3. Perform the following steps as shown in the illustration:

a. Lift to release the locking tab [1].

b. Disconnect the touchpad and power button cable [2].

4. Perform the following steps as shown in the illustration:

a. Lift the locking tab [1].

b. Disconnect the display assembly cable [2].

c. Unroute the display assembly cable [3].

5. Perform the following steps as shown in the illustration:

a. Remove the screw that secures the power connector to the computer [1].

b. Unroute the power connector cable [2].

6. Perform the following steps as shown in the illustration:

a. Remove the screw that secures the system board to the chassis [1].

b. Lift and remove the system board from the chassis [2].

Installing the System Board

1. Install the system board into the chassis.

2. Tighten the screws to secure the system board to the computer.

3. Connect the power connector to the system board.

4. Connect the display assembly cable to the system board.

5. Install:

a. base cover

b. keyboard

c. memory module

d. hard drive

e. WLAN card

f. access panel

g. optical-disk drive

h. battery

6. Follow the procedures in After Working Inside Your computer.

Removing the Power Connector

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. optical-disk drive

c. access panel

d. hard drive

e. memory module

f. keyboard

g. base cover

h. system board

3. Disconnect the power connector from the system board and lift it away from the system board.

Installing the Power Connector

1. Insert the power connector into its slot on the chassis and guide the cable into the retention tabs.

2. Connect the power connector cable to the system board.

3. Install:

a. system board

b. base cover

c. keyboard

d. memory module

e. hard drive

f. access panel

g. optical-disk drive

h. battery

4. Follow the procedures in After Working Inside Your computer .

Removing the Display Assembly

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. optical-disk drive

c. access panel

d. hard drive

e. memory module

f. keyboard

3. Perform the following steps as shown in the illustration:

a. Lift the tab and disconnect the display assembly cable [1] [2].

b. Unroute the display assembly cable [3].

c. Unroute the WLAN cable [4].

4. Remove the hinge screws that secure the display assembly to the computer.

5. Perform the following steps as shown in the illustration:

a. Lift the display assembly [1].

b. Slide the display assembly in the direction indicated to remove it from the chassis [2].

Installing the Display Assembly

1. Align the display assembly to the chassis.

2. Route the WLAN and display assembly cables through their tabs and then tighten the display hinges

screws to secure the display assembly.

3. Install:

a. keyboard

b. memory module

c. hard drive

d. access panel

e. optical-disk drive

f. battery

4. Follow the procedures in After Working Inside Your computer.

Removing the Display Bezel

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. optical-disk drive

c. access panel

d. hard drive

e. memory module

f. keyboard

g. system board

h. display assembly

3. Perform the following steps as shown in the illustration:

a. Place the display panel on a stable surface and pry along the edges of the display panel [1].

b. Remove the display bezel from the computer [2].

Installing the Display Bezel

1. Align and press the display bezel to fasten it to the display assembly.

2. Install:

a. display assembly

b. system board

c. keyboard

d. memory module

e. hard drive

f. access panel

g. optical-disk drive

h. battery

3. Follow the procedures in After Working Inside Your computer .

Removing the Camera

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. optical-disk drive

c. access panel

d. hard drive

e. memory module

f. keyboard

g. base cover

h. system board

i. display assembly

3. Perform the following steps as shown in the illustration:

a. Remove the tape that secures the camera cable [1].

b. Disconnect the camera cable from the camera [2].

c. Remove the camera from the display assembly [3].

Installing the Camera

1. Install the camera onto the display assembly.

2. Install:

a. display assembly

b. base cover

c. keyboard

d. memory module

e. WLAN card

f. hard drive

g. access panel

h. optical-disk drive

i. battery

3. Follow the procedures in After Working Inside Your computer.

Removing the Display Hinges

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. optical-disk drive

c. access panel

d. hard drive

e. memory module

f. keyboard

g. system board

h. display assembly

i. display bezel

3. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the display hinges to the display assembly [1].

b. Remove the display hinges [2].

Installing the Display Hinges

1. Tighten the screws to secure the display hinges to the display assembly.

2. Install:

a. display bezel

b. display assembly

c. system board

d. keyboard

e. memory module

f. hard drive

g. access panel

h. optical-disk drive

i. battery

3. Follow the procedures in After Working Inside Your computer .

Removing the Display Panel

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. battery

b. optical-disk drive

c. access panel

d. hard drive

e. memory module

f. keyboard

g. system board

h. display assembly

i. display bezel

j. display hinges

3. Perform the following steps as shown in the illustration:

a. Remove the screws that secure the display panel to the display assembly [1].

b. Lift the display panel to access the cables underneath [2].

4. Perform the following steps as shown in the illustration:

a. Remove the tape that secures the eDP cable to the computer [1].

b. Lift and remove the eDP cable [2].

5. Perform the following steps as shown in the illustration:

a. Disconnect the eDP cable from the computer [1].

b. Remove the display panel from the computer [2].

Installing the Display Panel

1. Connect the display cable to the display panel.

2. Affix the tape to secure the display cable.

3. Place the display panel on the display assembly.

4. Tighten the screws to secure the display panel to the display assembly.

5. Install:

a. display hinges

b. display bezel

c. display assembly

d. system board

e. keyboard

f. memory module

g. hard drive

h. access panel

i. optical-disk drive

j. battery

6. Follow the procedures in After Working Inside Your computer .

System Setup

System Setup enables you to manage your computer hardware and specify BIOS‐level options. From the

System Setup, you can:

• Change the NVRAM settings after you add or remove hardware

• View the system hardware configuration

• Enable or disable integrated devices

• Set performance and power management thresholds

• Manage your computer security

Boot Sequence

Boot Sequence allows you to bypass the System Setup‐defined boot device order and boot directly to a

specific device (for example: optical drive or hard drive). During the Power-on Self Test (POST), when the

Dell logo appears, you can:

• Access System Setup by pressing <F2> key

• Bring up the one-time boot menu by pressing <F12> key

The one-time boot menu displays the devices that you can boot from including the diagnostic option.

The boot-menu options are:

• Removable Drive (if available)

• STXXXX Drive

NOTE: XXX denotes the SATA drive number.

• Optical Drive

• Diagnostics

NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.

The boot sequence screen also displays the option to access the System Setup screen.

Navigation Keys

The following table displays the system setup navigation keys.

NOTE: For most of the system setup options, changes that you make are recorded but do not take

effect until you re-start the system.

Table 1. Navigation Keys

Keys Navigation

Up arrow Moves to the previous field.

Down arrow Moves to the next field.

<Enter> Allows you to select a value in the selected field (if applicable) or follow the link in

the field.

Spacebar Expands or collapses a drop‐down list, if applicable.

<Tab> Moves to the next focus area.

NOTE: For the standard graphics browser only.

<Esc> Moves to the previous page till you view the main screen. Pressing <Esc> in the main

screen displays a message that prompts you to save any unsaved changes and

restarts the system.

<F1> Displays the System Setup help file.

System Setup Options

NOTE: Depending on the computer and its installed devices, the items listed in this section may or

may not appear.

Table 2. General

Option Description

System

Information

This section lists the primary hardware features of your computer.

• System Information: Displays BIOS Version, Service Tag, Asset Tag, Ownership

Tag, Ownership Date, Manufacture Date, and the Express Service Code.

• Memory Information: Displays Memory Installed, Memory Available, Memory

Speed, Memory Channels Mode, Memory Technology, DIMM A Size, DIMM B Size,

• Processor Information: Displays Processor Type, Core Count, Processor ID,

Current Clock Speed, Minimum Clock Speed, Maximum Clock Speed, Processor

L2 Cache, Processor L3 Cache, HT Capable, and 64-Bit Technology.

• Device Information: Displays Primary Hard Drive, ODD Device, LOM MAC Address,

Video Controller, Video BIOS Version, Video Memory, Panel Type, Native

Resolution, Audio Controller, Wi-Fi Device, Bluetooth Device.

Battery

Information

Displays the battery status and the type of AC adapter connected to the computer.

Boot Sequence Boot Sequence Allows you to change the order in which

the computer attempts to find an

operating system. The options are:

• Windows Boot Manager

• UEFI

By default, all the options are checked.

You can also deselect any option or

change the boot order.

Option Description

Boot List Option Allows you to change the boot list option.

• Legacy

• UEFI

Advanced Boot

Options

This option allows you the legacy option ROMs to load. By default, the Enable Legacy

Option ROMs is disabled.

Date/Time Allows you to change the date and time.

Table 3. System Configuration

Option Description

Integrated NIC Allows you to configure the integrated network controller. The options

are:

• Disabled

• Enabled

• Enabled w/PXE: This option is enabled by default.

SATA Operation Allows you to configure the internal SATA hard-drive controller. The

options are:

• Disabled

• AHCI: This option is enabled by default.

Drives Allows you to configure the SATA drives on board. All drives are enabled

by default. The options are:

• SATA-0: This option is selected by default.

• SATA-1: This option is selected by default.

SMART Reporting This field controls whether hard drive errors for integrated drives are

reported during system startup. This technology is part of the SMART

(Self Monitoring Analysis and Reporting Technology) specification. This

option is disabled by default.

• Enable SMART Reporting

USB Configuration This field configures the integrated USB controller. If Boot Support is

enabled, the system is allowed to boot any type of USB Mass Storage

Devices (HDD, memory key, floppy).

If USB port is enabled, device attached to this port is enabled and

available for OS.

If USB port is disabled, the OS cannot see any device attached to this

port.

• Enable Boot Support

• Enable External USB Port

• Enable USB3.0 Controller

Option Description

NOTE: USB keyboard and mouse always work in the BIOS setup

irrespective of these settings.

Audio This field enables or disables the integrated audio controller. By default,

the Enable Audio option is selected.

Miscellaneous Devices Allows you to enable or disable the following devices:

• Enable Microphone

• Enable Camera

• Enable Media Card

• Disable Media Card

NOTE: All devices are enabled by default.

You can also enable or disable Media Card.

Table 4. Video

Option Description

LCD Brightness Allows you to set the display brightness depending up on the power

source (On Battery and On AC).

NOTE: The Video setting will only be visible when a video card is

installed into the system.

Switchable Graphics This option enables or disables switchable graphics technologies. Allows

you to set the display brightness depending up on the power source (On

Battery and On AC).

NOTE: It should only be enabled for Windows 7 and later version of

Windows or the Ubuntu OS.

Table 5. Security

Option Description

Admin Password Allows you to set, change, or delete the administrator (admin) password.

NOTE: You must set the admin password before you set the system

or hard drive password. Deleting the admin password automatically

deletes the system password and the hard drive password.

NOTE: Successful password changes take effect immediately.

Default Setting: Not set

System Password Allows you to set, change or delete the system password.

NOTE: Successful password changes take effect immediately.

Default Setting: Not set

Option Description

Internal HDD-0 Password Allows you to set, change or delete the password on the system's

internal hard-disk drive.

NOTE: Successful password changes take effect immediately.

Default Setting: Not set

Strong Password Allows you to enforce the option to always set strong passwords.

Default Setting: Enable Strong Password is not selected.

NOTE: If Strong Password is enabled, Admin and System passwords

must contain at least one uppercase character, one lowercase

character and be at least 8 characters long.

Password Configuration Allows you to determine the minimum and maximum length of

Administrator and System passwords.

Password Bypass Allows you to enable or disable the permission to bypass the System and

the Internal HDD password, when they are set. The options are:

• Disabled

• Reboot bypass

Default Setting: Disabled

Password Change Allows you to enable the disable permission to the System and Hard

Drive passwords when the admin password is set.

Default Setting: Allow Non-Admin Password Changes is selected.

Non-Admin Setup Changes Allows you to determine whether changes to the setup options are

allowed when an Administrator Password is set. If disabled the setup

options are locked by the admin password.

CPU XD Support Allows you to enable the Execute Disable mode of the processor.

Enable CPU XD Support (default)

Admin Setup Lockout Allows you to prevent users from entering Setup when an Administrator

password is set.

Default Setting: Enable Admin Setup Lockout is not selected.

Table 6. Secure Boot

Option Description

Secure Boot Enable This option enables or disables the Secure Boot Feature.

• Disabled

• Enabled

Option Description

Default Setting: The option is disabled.

Expert Key Management Allows you to manipulate the security key databases only if the system is

in Custom Mode. The Enable Custom Mode option is disabled by

default. The options are:

• PK

• KEK

• db

• dbx

If you enable the Custom Mode, the relevant options for PK, KEK, db,

and dbx appear. The options are:

•Save to File- Saves the key to a user-selected file

•Replace from File- Replaces the current key with a key from a user-

selected file

•Append from File- Adds a key to the current database from a user-

selected file

•Delete- Deletes the selected key

•Reset All Keys- Resets to default setting

•Delete All Keys- Deletes all the keys

NOTE: If you disable the Custom Mode, all the changes made will

be erased and the keys will restore to default settings.

Table 7. Performance

Option Description

Multi Core Support This field specifies whether the process will have one or all cores

enabled. The performance of some applications will improve with the

additional cores. This option is enabled by default. Allows you to enable

or disable multi-core support for the processor. The installed processor

supports two cores. If you enable Multi Core Support, two cores will be

enabled. If you disable Multi Core Support, one core will be enabled.

• Enable Multi Core Support

Default Setting: The option is enabled.

Intel SpeedStep Allows you to enable or disable the Intel SpeedStep feature.

• Enable Intel SpeedStep

Default Setting: The option is enabled.

C States Control Allows you to enable or disable the additional processor sleep states.

• C states

Default Setting: The option is enabled.

Option Description

Intel TurboBoost Allows you to enable or disable the Intel TurboBoost mode of the

processor.

• Enable Intel TurboBoost

Default Setting: The option is enabled.

Hyper-Thread Control Allows you to enable or disable the HyperThreading in the processor.

• Disabled

• Enabled

Default Setting: The option is enabled.

Table 8. Power Management

Option Description

AC Behavior Allows you to enable or disable the computer from turning on

automatically when an AC adapter is connected.

Default Setting: Wake on AC is not selected.

Auto On Time Allows you to set the time at which the computer must turn on

automatically. The options are:

• Disabled (default)

• Every Day

• Weekdays

• Select Days

USB Wake Support Allows you to enable USB devices to wake the system from Standby.

NOTE: This feature is only functional when the AC power adapter is

connected. If the AC power adapter is removed during Standby, the

system setup will remove power from all of the USB ports to

conserve battery power.

• Enable USB Wake Support

Default Setting: The option is disabled.

Wake on LAN/WLAN Allows you to enable or disable the feature that powers on the computer

from the Off state when triggered by a LAN signal.

• Disabled: This option is enabled by default

• LAN Only

Advanced Battery Charge

Configuration

This option enables you to maximize the battery health. By enabling this

option, your system uses the standard charging algorithm and other

techniques, during the non-work hours to improve the battery health.

Disabled (default)

Option Description

Primary Battery Charge

Configuration

Allows you to select the charging mode for the battery. The options are:

• Adaptive

• Standard - Fully charges your battery at a standard rate.

• Primarily AC use

• Custom

If Custom Charge is selected, you can also configure Custom Charge

Start and Custom Charge Stop.

NOTE: All charging mode may not be available for all the batteries.

To enable this option, disable the Advanced Battery Charge

Configuration option.

Table 9. POST Behavior

Option Description

Adapter Warnings Allows you to enable or disable the system setup (BIOS) warning

messages when you use certain power adapters.

Default Setting: Enable Adapter Warnings

Fn Lock Option Allows the hot key combination <Fn> +<Esc> toggle the primary

behavior of F1–F12, between the standard and secondary functions.

• Lock Mode Disable/Standard. This option is enabled by default.

• Lock Mode Enable/Secondary

Fastboot Allows you to speed up the boot process by bypassing some of the

compatibility steps. The options are:

• Minimal

• Thorough (default)

• Auto

Table 10. Virtualization Support

Option Description

Virtualization Allows you to enable or disable the Intel Virtualization Technology.

•Enable Intel Virtualization Technology (default)

VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the

additional hardware capabilities provided by Intel® Virtualization

technology for direct I/O.

Enable VT for Direct I/O — enabled by default.

Table 11. Wireless

Option Description

Wireless Switch Allows to set the wireless devices that can be controlled

by the wireless switch. The options are:

• WLAN/WiGig

• Bluetooth

All the options are enabled by default.

Wireless Device Enable Allows you to enable or disable the internal wireless

devices.

• WLAN/WiGig

• Bluetooth

All the options are enabled by default.

Table 12. Maintenance

Option Description

Service Tag Displays the Service Tag of your computer.

Asset Tag Allows you to create a system asset tag if an asset tag is not already set.

This option is not set by default.

BIOS Downgrade This field controls flashing of the system firmware to pervious revisions.

Allows BIOS Downgrade (Enabled by default)

Table 13. System Logs

Option Description

BIOS Events Allows you to view and clear the System Setup (BIOS) POST events.

Updating the BIOS

It is recommended to update your BIOS (system setup), on replacing the system board or if an update is

available. For laptops, ensure that your computer battery is fully charged and connected to a power

outlet

1. Re-start the computer.

2. Go to dell.com/support.

3. Enter the Service Tag or Express Service Code and click Submit.

NOTE: To locate the Service Tag, click Where is my Service Tag?

NOTE: If you cannot find your Service Tag, click Detect My Product. Proceed with the

instructions on screen.

4. If you are unable to locate or find the Service Tag, click the Product Category of your computer.

5. Choose the Product Type from the list.

6. Select your computer model and the Product Support page of your computer appears.

7. Click Get drivers and click View All Drivers.

The Drivers and Downloads page opens.

8. On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS.

9. Identify the latest BIOS file and click Download File.

You can also analyze which drivers need an update. To do this for your product, click Analyze

System for Updates and follow the instructions on the screen.

10. Select your preferred download method in the Please select your download method below window,

click Download File.

The File Download window appears.

11. Click Save to save the file on your computer.

12. Click Run to install the updated BIOS settings on your computer.

Follow the instructions on the screen.

System and Setup Password

You can create a system password and a setup password to secure your computer.

Password Type Description

System password Password that you must enter to log on to your system.

Setup password Password that you must enter to access and make changes to the BIOS settings of

your computer.

CAUTION: The password features provide a basic level of security for the data on your computer.

CAUTION: Anyone can access the data stored on your computer if it is not locked and left

unattended.

NOTE: Your computer is shipped with the system and setup password feature disabled.

Assigning a System Password and Setup Password

You can assign a new System Password and/or Setup Password or change an existing System Password

and/or Setup Password only when Password Status is Unlocked. If the Password Status is Locked, you

cannot change the System Password.

NOTE: If the password jumper is disabled, the existing System Password and Setup Password are

deleted and you need not provide the system password to log on to the computer.

To enter a system setup, press <F2> immediately after a power-on or re-boot.

1. In the System BIOS or System Setup screen, select System Security and press <Enter>.

The System Security screen appears.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password , enter your system password, and press <Enter> or <Tab>.

Use the following guidelines to assign the system password:

• A password can have up to 32 characters.

• The password can contain the numbers 0 through 9.

• Only lower case letters are valid, upper case letters are not allowed.

• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

Re-enter the system password when prompted.

4. Type the system password that you entered earlier and click OK.

5. Select Setup Password, type your system password and press <Enter> or <Tab>.

A message prompts you to re-type the setup password.

6. Type the setup password that you entered earlier and click OK.

7. Press <Esc> and a message prompts you to save the changes.

8. Press <Y> to save the changes.

The computer reboots.

Deleting or Changing an Existing System and/or Setup Password

Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change

the existing System and/or Setup password. You cannot delete or change an existing System or Setup

password, if the Password Status is Locked.

To enter the System Setup, press <F2> immediately after a power-on or reboot.

1. In the System BIOS or System Setup screen, select System Security and press <Enter>.

The System Security screen is displayed.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password, alter or delete the existing system password and press <Enter> or <Tab>.

4. Select Setup Password, alter or delete the existing setup password and press <Enter> or <Tab>.

NOTE: If you change the System and/or Setup password, re-enter the new password when

promoted. If you delete the System and/or Setup password, confirm the deletion when

promoted.

5. Press <Esc> and a message prompts you to save the changes.

6. Press <Y> to save the changes and exit from the System Setup.

The computer reboots.

Diagnostics

Enhanced Pre-Boot System Assessment (ePSA)

Diagnostics

The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware.

The ePSA is embedded with the BIOS and is launched by the BIOS internally. The embedded system

diagnostics provides a set of options for particular devices or device groups allowing you to:

• Run tests automatically or in an interactive mode

• Repeat tests

• Display or save test results

• Run thorough tests to introduce additional test options to provide extra information about the failed

device(s)

• View status messages that inform you if tests are completed successfully

• View error messages that inform you of problems encountered during testing

CAUTION: Use the system diagnostics to test only your computer. Using this program with other

computers may cause invalid results or error messages.

NOTE: Some tests for specific devices require user interaction. Always ensure that you are present

at the computer terminal when the diagnostic tests are performed.

1. Power-on the computer.

2. As the computer boots, press the <F12> key as the Dell logo appears.

3. On the boot menu screen, select the Diagnostics option.

The Enhanced Pre-boot System Assessment window is displayed, listing all devices detected in the

computer. The diagnostics starts running the tests on all the detected devices.

4. If you wish to run a diagnostic test on a specific device, press <Esc> and click Yes to stop the

diagnostic test.

5. Select the device from the left pane and click Run Tests.

6. If there are any issues, error codes are displayed.

Note the error code and contact Dell.

Specifications

NOTE: Offerings may vary by region. For more information regarding the configuration of your

computer, click Start (Start icon) → Help and Support, and then select the option to view

information about your computer.

Table 14. System Information

Feature Description

Chipset integrated in processor

DRAM bus width 64 bits

Flash EPROM 8 MB

Table 15. Processor

Feature Description

Processor Type • 4th Generation Intel core i3

• 5th Generation Intel core i3/i5/i7

• Intel Celeron Dual Core

• Intel Pentium Quard Core

L1 cache 128 KB

L2 cache 512 KB

L3 cache Up to 4 MB

Table 16. Memory

Feature Description

Memory connector two internally accessible DDR3L connector

Memory capacity 2 GB, 4 GB, and 8 GB

Memory speed 1600 MHz

Minimum memory 2 GB

Maximum memory 16 GB

Table 17. Audio

Feature Description

Type 2 channel high-definition audio

Controller Realtek ALC3234 with Waves Maxx Audio

Stereo conversion 24-bit (analog-to-digital and digital-to-analog)

Interface Intel HDA bus

Speakers 2 x 2 W

Volume controls program menu and keyboard media-control keys

Table 18. Video

Feature Description

Video type eDP

Video Controller:

UMA Intel HD Graphics (shared memory)

Discrete NVIDIA GeForce 820M (up to 2GB DDR3)

Data bus: 64 bits

External display support VGA

Table 19. Camera

Feature Description

Camera Resolution HD resolution

Video Resolution (maximum) 1280 x 720 (HD) at 30 fps (maximum)

Diagonal viewing angle 74°

Table 20. Communication

Feature Description

Network adapter 10/100/1000 Mbps Ethernet LAN on Motherboard (LOM)

Wireless • Wi-Fi 802.11 b/g/n

• Bluetooth 4.0

Table 21. Ports and Connectors

Feature Description

Audio one headphone/microphone combo port (headset)

Video VGA

Network adapter one RJ-45 port

USB: • one USB 3.0 port

Feature Description

• two USB 2.0 ports

NOTE: The powered USB 3.0 connector also supports Microsoft Kernel Debugging. The ports are

identified in the documentation shipped with your computer.

Media card reader one SD slot

Table 22. Display

Feature Vostro 15–3558

Type

• 15.6 inches HD WLED

• 15.6 inches FHD Non-touch

Dimensions:

HD Non-touch FHD Non-touch

Height 224.30 mm (8.83 inches) 223.80 mm (8.81 inches)

Diagonal 396.24 mm (15.60 inches) 396.24 mm (15.60 inches)

Width 360.00 mm (14.17 inches) 359.50 mm (14.15 inches)

Maximum

resolution

1366 x 768 pixels 1920 x 1080 pixels

Active area (X/Y) 344.20 mm x 193.50 mm (13.55 inches x 7.62 inches)

Maximum

Brightness

200 nits

Operating angle 0° (closed) to 135°

Refresh rate 60 Hz

Minimum Viewing angles:

Horizontal 40° / 40°

Vertical 10° / 30°

Pixel pitch 0.2265 mm

Table 23. Keyboard

Feature Description

Number of keys: US 101, Brazil 104, UK 102, and Japan 105

Table 24. Touchpad

Feature Description

Active Area:

X-axis 105.00 mm (4.13 inches)

Feature Description

Y-axis 80.00 mm (3.14 inches)

Table 25. Battery

Feature Description

Type • 4-cell “smart” lithium ion (47 WHr)

Dimensions:

Height 20.00 mm (0.78 inch)

Width 270.00 mm (10.63 inches)

Depth 37.50 mm (1.47 inches)

Weight 0.26 kg (0.56 lb)

Life span 300 discharge/charge cycles

Voltage 14.80 VDC

Temperature range:

Operating 0 °C to 35 °C (32 °F to 95 °F)

Non-Operating –40 °C to 65 °C (–40 °F to 149 °F)

Coin-cell battery 3 V CR2032 lithium ion

Table 26. AC Adapter

Feature Description

Type 45 W

65 W

Input voltage 100 VAC to 240 VAC

Input frequency 50 Hz-60 Hz

Input current (maximum)

45 W 1.30 A

65 W 1.70 A

Output current

45 W 2.31 A

65 W 3.34 A

Rated output voltage 19.50 VDC

Temperature range:

Operating 0 °C to 40 °C (32 °F to 104 °F)

Non-Operating –40 °C to 70 °C (–40 °F to 158 °F)

Table 27. Physical

Feature Description

Height:

Touch 24.05 mm (0.95 inch)

Non-Touch 23.75 mm (0.93 inch)

Width: 380.00 mm (14.96 inches)

Depth: 260.40 mm (10.25 inches)

Weight:

Touch 2.39 kg (5.28 lb)

Non-Touch 2.24 kg (4.94 lb)

Table 28. Environmental

Feature Description

Temperature:

Operating 0 °C to 35 °C (32 °F to 95 °F)

Storage –40 °C to 65 °C (–40 °F to 149 °F)

Relative humidity (maximum):

Operating 10 % to 90 % (non-condensing)

Storage 0 % to 95 % (non-condensing)

Altitude (maximum):

Operating –15.2 m to 3048 m (–50 to 10,000 ft)

0° to 35°C

Non-Operating –15.2 m to 10,668 m (–50 ft to 35,000 ft)

Airborne contaminant level G1 as defined by ISA-S71.04-1985

Contacting Dell

NOTE: If you do not have an active Internet connection, you can find contact information on your

purchase invoice, packing slip, bill, or Dell product catalog.

Dell provides several online and telephone-based support and service options. Availability varies by

country and product, and some services may not be available in your area. To contact Dell for sales,

technical support, or customer service issues:

1. Go to dell.com/support.

2. Select your support category.

3. Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the

page.

4. Select the appropriate service or support link based on your need.

Table of Contents

DELL 3558 User Manual

Related Manuals