Dell Vostro 15–3578 Owner's Manual
Working on your computer
Removing and installing components
Technology and components
- HDMI 1.4
  - HDMI 1.4 Features
  - Advantages of HDMI
- USB features
System specifications
- Technical specifications
- Hot key combinations
System setup
Software
Troubleshooting
Contacting Dell

DELL 3578 User Manual

Displayed below is the user manual for 3578 by DELL which is a product in the Notebooks category. This manual has pages.

Related Manuals

DELL 3578 Manual

Dell Vostro 15–3578

Owner's Manual

Regulatory Model: P63F

Regulatory Type: P63F002

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

may be trademarks of their respective owners.

2018 - 01

Rev. A01

Contents

1 Working on your computer............................................................................................................................. 6

Safety precautions............................................................................................................................................................. 6

Standby power............................................................................................................................................................. 6

Bonding ........................................................................................................................................................................ 6

Electrostatic discharge — ESD protection...............................................................................................................6

ESD eld service kit .................................................................................................................................................... 7

Transporting sensitive components........................................................................................................................... 8

Before working inside your computer..............................................................................................................................8

After working inside your computer.................................................................................................................................8

2 Removing and installing components............................................................................................................10

Recommended tools........................................................................................................................................................ 10

Screw size list....................................................................................................................................................................10

Battery................................................................................................................................................................................ 11

Removing the battery................................................................................................................................................. 11

Installing the battery....................................................................................................................................................11

Optical drive...................................................................................................................................................................... 12

Removing the optical drive .......................................................................................................................................12

Removing the optical drive bracket..........................................................................................................................12

Installing the optical drive bracket............................................................................................................................ 13

Installing the optical drive.......................................................................................................................................... 13

Keyboard............................................................................................................................................................................ 13

Removing the keyboard............................................................................................................................................. 13

Installing the keyboard............................................................................................................................................... 15

Base cover.........................................................................................................................................................................15

Removing the base cover..........................................................................................................................................15

Installing the base cover............................................................................................................................................ 18

Hard drive.......................................................................................................................................................................... 18

Removing the hard drive assembly...........................................................................................................................18

Removing the hard drive from the hard drive bracket...........................................................................................19

Installing the hard drive into the hard drive bracket.............................................................................................. 20

Installing the hard drive assembly.............................................................................................................................21

Fingerprint reader............................................................................................................................................................. 21

Removing the ngerprint reader...............................................................................................................................21

Installing the ngerprint reader................................................................................................................................ 23

WLAN card....................................................................................................................................................................... 23

Removing the WLAN card........................................................................................................................................ 23

Installing the WLAN card.......................................................................................................................................... 24

Memory modules............................................................................................................................................................. 25

Removing the memory module................................................................................................................................ 25

Installing the memory module...................................................................................................................................25

Coin cell battery............................................................................................................................................................... 26

Removing the coin cell battery.................................................................................................................................26

Contents 3

Installing the coin cell battery................................................................................................................................... 27

Power button board.........................................................................................................................................................27

Removing the power button board..........................................................................................................................27

Installing the power button board............................................................................................................................ 28

Heat sink .......................................................................................................................................................................... 28

Removing the heat sink ............................................................................................................................................28

Installing the heat sink ..............................................................................................................................................29

System fan........................................................................................................................................................................29

Removing the system fan......................................................................................................................................... 29

Installing the system fan........................................................................................................................................... 30

Speaker.............................................................................................................................................................................. 31

Removing the speakers..............................................................................................................................................31

Installing the speakers................................................................................................................................................ 31

System board....................................................................................................................................................................32

Removing the system board.....................................................................................................................................32

Installing the system board....................................................................................................................................... 35

Input/Output(I/O) boards.............................................................................................................................................. 36

Removing the Input and Output board .................................................................................................................. 36

Installing the Input and Output board .....................................................................................................................37

Power connector port..................................................................................................................................................... 37

Removing the power connector...............................................................................................................................37

Installing the power connector.................................................................................................................................38

Display assembly.............................................................................................................................................................. 39

Removing the display assembly............................................................................................................................... 39

Installing the display assembly...................................................................................................................................41

Display bezel...................................................................................................................................................................... 41

Removing the display bezel.......................................................................................................................................42

Installing the display bezel.........................................................................................................................................42

Camera.............................................................................................................................................................................. 43

Removing the camera............................................................................................................................................... 43

Installing the camera..................................................................................................................................................44

Display panel..................................................................................................................................................................... 44

Removing the display panel...................................................................................................................................... 44

Installing the display panel.........................................................................................................................................46

Display hinges...................................................................................................................................................................46

Removing the display hinges.................................................................................................................................... 46

Installing the display hinges.......................................................................................................................................47

Touchpad...........................................................................................................................................................................48

Removing the touchpad............................................................................................................................................48

Installing the touchpad.............................................................................................................................................. 49

Palm rest........................................................................................................................................................................... 50

Removing the palmrest............................................................................................................................................. 50

Installing the palmrest................................................................................................................................................ 51

3 Technology and components........................................................................................................................52

HDMI 1.4............................................................................................................................................................................52

HDMI 1.4 Features......................................................................................................................................................52

4Contents

Advantages of HDMI................................................................................................................................................. 52

USB features.................................................................................................................................................................... 53

USB 3.0/USB 3.1 Gen 1 (SuperSpeed USB)...........................................................................................................53

Speed.......................................................................................................................................................................... 53

Applications.................................................................................................................................................................54

Compatibility...............................................................................................................................................................54

4 System specications..................................................................................................................................56

Technical specications...................................................................................................................................................56

Hot key combinations......................................................................................................................................................58

5 System setup...............................................................................................................................................59

Boot Sequence.................................................................................................................................................................59

Navigation keys................................................................................................................................................................ 59

System setup options......................................................................................................................................................60

Flashing the BIOS from the F12 One-Time boot menu............................................................................................... 68

Updating the BIOS in Windows .....................................................................................................................................72

System and setup password...........................................................................................................................................73

Assigning a system password and setup password............................................................................................... 73

Deleting or changing an existing system and or setup password........................................................................ 73

6 Software...................................................................................................................................................... 74

Supported operating systems.........................................................................................................................................74

Downloading drivers.........................................................................................................................................................74

Intel chipset drivers..........................................................................................................................................................75

Battery drivers..................................................................................................................................................................76

Intel HID Event Filter........................................................................................................................................................76

Intel Dynamic Platform and Thermal Framework......................................................................................................... 77

Disk drivers........................................................................................................................................................................77

Realtek PCI-E Memory Card...........................................................................................................................................77

Graphics controller driver................................................................................................................................................ 77

Bluetooth drivers..............................................................................................................................................................78

Network drivers................................................................................................................................................................78

Realtek Audio.................................................................................................................................................................... 78

Storage drivers................................................................................................................................................................. 79

Security drivers................................................................................................................................................................ 79

7 Troubleshooting........................................................................................................................................... 80

Enhanced Pre-Boot System Assessment — ePSA diagnostics................................................................................80

Running the ePSA diagnostics.................................................................................................................................80

Diagnostic LED.................................................................................................................................................................80

Real Time Clock reset.......................................................................................................................................................81

8 Contacting Dell............................................................................................................................................ 83

Contents 5

Working on your computer

Safety precautions

The safety precautions chapter details the primary steps to be taken before performing any disassembly instructions.

Observe the following safety precautions before you perform any installation or break/x procedures involving disassembly or reassembly:

• Turn o the system and all attached peripherals.

• Disconnect the system and all attached peripherals from AC power.

• Disconnect all network cables, telephone, and telecommunications lines from the system.

• Use an ESD eld service kit when working inside any notebook to avoid electrostatic discharge (ESD) damage.

• After removing any system component, carefully place the removed component on an anti-static mat.

• Wear shoes with non-conductive rubber soles to reduce the chance of getting electrocuted.

Standby power

Dell products with standby power must be unplugged before you open the case. Systems that incorporate standby power are essentially

powered while turned o. The internal power enables the system to be remotely turned on (wake on LAN) and suspended into a sleep

mode and has other advanced power management features.

Unplugging, pressing and holding the power button for 15 seconds should discharge residual power in the system board, notebooks

Bonding

Bonding is a method for connecting two or more grounding conductors to the same electrical potential. This is done through the use of a

eld service electrostatic discharge (ESD) kit. When connecting a bonding wire, ensure that it is connected to bare metal and never to a

painted or non-metal surface. The wrist strap should be secure and in full contact with your skin, and ensure that you remove all jewelry

such as watches, bracelets, or rings prior to bonding yourself and the equipment.

Electrostatic discharge — ESD protection

ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards, processors,

memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such as intermittent

problems or a shortened product life span. As the industry pushes for lower power requirements and increased density, ESD protection is an

increasing concern.

Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than in previous

Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.

Two recognized types of ESD damage are catastrophic and intermittent failures.

•Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes an immediate and

complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has received a static shock and

immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or nonfunctional memory.

•Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of intermittent failures

means that most of the time when damage occurs, it is not immediately recognizable. The DIMM receives a static shock, but the

6 Working on your computer

tracing is merely weakened and does not immediately produce outward symptoms related to the damage. The weakened trace may

take weeks or months to melt, and in the meantime may cause degradation of memory integrity, intermittent memory errors, etc.

The more dicult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded") failure.

Perform the following steps to prevent ESD damage:

• Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do not provide

adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts with increased

sensitivity to ESD damage.

• Handle all static-sensitive components in a static-safe area. If possible, use anti-static oor pads and workbench pads.

• When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static packing

material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you discharge static

electricity from your body.

• Before transporting a static-sensitive component, place it in an anti-static container or packaging.

ESD eld service kit

The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components: anti-static

mat, wrist strap, and bonding wire.

Components of an ESD eld service kit

The components of an ESD eld service kit are:

•Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an anti-static

mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal on the system being

worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly on the mat. ESD-sensitive

items are safe in your hand, on the ESD mat, in the system, or inside a bag.

•Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist and bare metal

on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that is temporarily placed on

the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD mat, and the hardware is known as

bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never use wireless wrist straps. Always be aware that the

internal wires of a wrist strap are prone to damage from normal wear and tear, and must be checked regularly with a wrist strap tester

in order to avoid accidental ESD hardware damage. It is recommended to test the wrist strap and bonding wire at least once per week.

•ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored kit, it is a best

practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A wrist strap tester is the best

method for doing this test. If you do not have your own wrist strap tester, check with your regional oce to nd out if they have one.

To perform the test, plug the wrist-strap's bonding-wire into the tester while it is strapped to your wrist and push the button to test. A

green LED is lit if the test is successful; a red LED is lit and an alarm sounds if the test fails.

•Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts that are

insulators and often highly charged.

•Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For example,

deploying the kit for a server environment is dierent than for a desktop or portable environment. Servers are typically installed in a rack

within a data center; desktops or portables are typically placed on oce desks or cubicles. Always look for a large open at work area

that is free of clutter and large enough to deploy the ESD kit with additional space to accommodate the type of system that is being

repaired. The workspace should also be free of insulators that can cause an ESD event. On the work area, insulators such as Styrofoam

and other plastics should always be moved at least 12 inches or 30 centimeters away from sensitive parts before physically handling any

hardware components

•ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded bags are

preferred. However, you should always return the damaged part using the same ESD bag and packaging that the new part arrived in.

The ESD bag should be folded over and taped shut and all the same foam packing material should be used in the original box that the

new part arrived in. ESD-sensitive devices should be removed from packaging only at an ESD-protected work surface, and parts should

never be placed on top of the ESD bag because only the inside of the bag is shielded. Always place parts in your hand, on the ESD mat,

in the system, or inside an anti-static bag.

•Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts to be

returned to Dell, it is critical to place these parts in anti-static bags for safe transport.

Working on your computer 7

ESD protection summary

It is recommended that all eld service technicians use the traditional wired ESD grounding wrist strap and protective anti-static mat at all

times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all insulator parts while

performing service and that they use anti-static bags for transporting sensitive components.

Transporting sensitive components

When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place these parts in

anti-static bags for safe transport.

Lifting equipment

Adhere to the following guidelines when lifting heavy weight equipment:

CAUTION: Do not lift greater than 50 pounds. Always obtain additional resources or use a mechanical lifting device.

1 Get a rm balanced footing. Keep your feet apart for a stable base, and point your toes out.

2 Tighten stomach muscles. Abdominal muscles support your spine when you lift, osetting the force of the load.

3 Lift with your legs, not your back.

4 Keep the load close. The closer it is to your spine, the less force it exerts on your back.

5 Keep your back upright, whether lifting or setting down the load. Do not add the weight of your body to the load. Avoid twisting your

body and back.

6 Follow the same techniques in reverse to set the load down.

Before working inside your computer

1 Ensure that your work surface is at and clean to prevent the computer cover from being scratched.

2 Turn o your computer.

3 If the computer is connected to a docking device (docked), undock it.

4 Disconnect all network cables from the computer (if available).

CAUTION: If your computer has an RJ45 port, disconnect the network cable by rst unplugging the cable from your

computer.

5 Disconnect your computer and all attached devices from their electrical outlets.

6 Open the display.

7 Press and hold the power button for few seconds, to ground the system board.

CAUTION: To guard against electrical shock unplug your computer from the electrical outlet before performing Step # 8.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an

unpainted metal surface at the same time as touching a connector on the back of the computer.

8 Remove any installed ExpressCards or Smart Cards from the appropriate slots.

After working inside your computer

After you complete any replacement procedure, ensure that you connect external devices, cards, and cables before turning on your

computer.

8Working on your computer

CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries

designed for other Dell computers.

1 Connect any external devices, such as a port replicator or media base, and replace any cards, such as an ExpressCard.

2 Connect any telephone or network cables to your computer.

CAUTION: To connect a network cable, rst plug the cable into the network device and then plug it into the

computer.

3 Connect your computer and all attached devices to their electrical outlets.

4 Turn on your computer.

Working on your computer 9

Removing and installing components

This section provides detailed information on how to remove or install the components from your computer.

Recommended tools

The procedures in this document require the following tools:

• Phillips #0 screwdriver

• Phillips #1 screwdriver

• Plastic scribe

NOTE: The #0 screw driver is for screws 0-1 and the #1 screw driver is for screws 2-4

Screw size list

Table 1. Vostro 15–3578 screw size list

Component M2x2 (Big

head 07)

M2x2 (Big

head 05) M2x2.5 M2x5

M2x3

(Thin

head)

M2x3 M2.5x2.5

(Big head) M2.5x8 M3x3

Optical drive bridge 3

Optical drive

bracket 1

Base Cover 8 1 8

Hard drive 4

Hard drive bracket 4

System fan 2

System board 4 1

Support bracket 4 3

Display assembly 3

Display panel 4

Display Hinge 6

Power button board 1

Fingerprint reader

bracket 1

10 Removing and installing components

Battery

Removing the battery

1 Follow the procedure in Before working inside your computer.

2 To remove the battery:

a Slide the release latch to release the battery [1].

b Remove the battery from the computer [2].

Installing the battery

1 Insert the battery into the slot and press until it clicks into place.

2 Follow the procedures in After working inside your computer.

Removing and installing components 11

Optical drive

Removing the optical drive

1 Follow the procedure in Before working inside your computer.

2 Remove the Battery.

3 To remove the optical drive:

a Remove the M2x5 screw that secures the optical drive to the computer [1].

b Using a plastic scribe, push the tab in the direction of the arrow indicated on the chassis. [2].

c Slide the optical drive out of the computer [3].

Removing the optical drive bracket

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

3 To remove the optical drive from the bracket:

a Remove the M2x3 screw that secures the optical drive bracket.

12 Removing and installing components

b Remove the optical drive bracket from the optical drive .

Installing the optical drive bracket

1 Install the optical drive bracket.

2 Tighten the M2x3 screw to secure the optical drive bracket.

3 Install the:

aOptical drive

bBattery

4 Follow the procedure in After working inside your computer.

Installing the optical drive

1 Insert the optical drive into the slot until it clicks into place.

2 Tighten the M2x5 screw to secure the optical drive to the computer.

3 Install the Battery.

4 Follow the procedure in After working inside your computer.

Keyboard

Removing the keyboard

1 Follow the procedure in Before working inside your computer.

2 Remove the Battery.

3 To remove the keyboard:

a Using a plastic scribe, release the ve tabs from the slots located above the keyboard [1].

b Flip the keyboard on the palm rest to access the keyboard connector cable under the keyboard [2].

Removing and installing components 13

4 To remove the keyboard cable:

a Disconnect the keyboard cable from the system board.

b Remove the keyboard from the computer.

14 Removing and installing components

Installing the keyboard

1 Connect the keyboard cable to the connector on the system board.

2 Slide the keyboard to align it with the tabs.

3 Press along the top edges to lock the keyboard in place.

4 Install the Battery.

5 Follow the procedure in After working inside your computer.

Base cover

Removing the base cover

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

cKeyboard

3 To remove the base cover:

a Disconnect the optical drive connector and lift it to remove it from the system board [1].

Removing and installing components 15

b Remove the 5 (M2x5) screws that secure the base cover [2].

4 Flip the computer and remove the screws (8 screws - M2.5x8; 3 screws - M2x2; 2 screws- M2x5) that secure the base cover to the

computer.

16 Removing and installing components

5 To remove the base cover:

a Use a scribe to pry the edges of the base cover [1].

b Lift the base cover and remove it from the computer [2].

Removing and installing components 17

Installing the base cover

1 Align the base cover with the screw holders on the computer.

2 Press the edges of the cover until it clicks into place.

3 Tighten the (8 screws - M2.5x8; 3 screws - M2x2; 2 screws- M2x5) screws to secure the base cover to the computer.

4 Flip the computer over.

5 Open the display and connect the optical drive connector to the system board.

6 Tighten the screws to secure the base cover to the palm rest.

7 Install the:

aKeyboard

bOptical drive

cBattery

8 Follow the procedure in After working inside your computer.

Hard drive

Removing the hard drive assembly

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

18 Removing and installing components

bOptical drive

cKeyboard

dBase cover

3 To remove the hard drive assembly:

a Disconnect the hard drive cable from the connector on the system board [1].

b Remove the 4 (M2x3) screws that secure the hard drive assembly to the computer [2].

c Lift the hard drive assembly away from the computer [3].

Removing the hard drive from the hard drive bracket

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

cKeyboard

dBase cover

eHard drive assembly

3 To remove the hard drive from the hard drive assembly:

a Pull the hard drive cable connector to remove it from the hard drive .

b Remove the 4 (M3x3) screws that secure the hard drive bracket to the hard drive [1].

c Lift the hard drive from the hard drive bracket [2].

Removing and installing components 19

Installing the hard drive into the hard drive bracket

1 Align the screw holders and insert the hard drive into the hard drive bracket.

2 Tighten the M3x3 screws to secure the hard drive to the hard drive bracket.

3 Connect the hard drive cable connector to the hard drive.

4 Install the:

aHard drive assembly

bBase cover

cKeyboard

20 Removing and installing components

dOptical drive

eBattery

5 Follow the procedure in After working inside your computer

Installing the hard drive assembly

1 Insert the hard drive assembly into the slot on the computer.

2 Tighten the 4 (M2x3) screws to secure the hard drive assembly to the computer.

3 Connect the hard drive cable to the connector on the system board.

4 Install the:

aBase cover

bKeyboard

cOptical drive

dBattery

5 Follow the procedures in After working inside your computer.

Fingerprint reader

Removing the ngerprint reader

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

cKeyboard

dBase cover

eHard drive

3 To remove the ngerprint reader bracket:

a Disconnect the ngerprint reader from the connector on the system board [1].

b Remove the tape that secures the ngerprint assembly to the computer [2]

c Remove the 1 (M2x2.5) screw that secures the ngerprint assembly to the computer [3].

d Lift the ngerprint reader bracket from the computer [4].

Removing and installing components 21

4 Remove the ngerprint reader

a Lift the ngerprint reader board from the computer.

22 Removing and installing components

Installing the ngerprint reader

1 Place the ngerprint reader board into the slot on the computer.

2 Tighten the 1 (M2x2.5) screw that secures the ngerprint reader bracket to the computer.

3 Ax the tape that secures the ngerprint assembly to the computer

4 Connect the ngerprint reader cable to the connector on the system board.

5 Install the:

aHard drive

bBase cover

cKeyboard

dOptical drive

eBattery

6 Follow the procedures in After working inside your computer.

WLAN card

Removing the WLAN card

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

cKeyboard

dBase cover

3 To remove the WLAN card:

a Remove the 1 (M2x3) screw that secures the tab to the WLAN card [1].

Removing and installing components 23

b Lift the tab that secures the WLAN card [2].

c Disconnect the WLAN cables from the connectors on the WLAN card [3].

d Slide the WLAN card from the connector on the system board [4].

Installing the WLAN card

1 Install the WLAN card to the connector on the system board.

2 Connect the WLAN cables to the connectors on the WLAN card.

3 Place the securing tab on the WLAN card and tighten the 1 (M2x3) screw on the computer.

4 Install the:

aBase cover

bKeyboard

cOptical drive

dBattery

5 Follow the procedure in After working inside your computer.

24 Removing and installing components

Memory modules

Removing the memory module

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

cKeyboard

dBase cover

3 To remove memory module:

a Pull the clips securing the memory module until the memory module pops up [1].

b Remove the memory module from the system board [2].

Installing the memory module

1 Insert the memory module into the memory socket.

2 Press the memory module until the clips secure the memory module.

3 Install the:

Removing and installing components 25

aBase cover

bKeyboard

cOptical drive

dBattery

4 Follow the procedures in After working inside your computer.

Coin cell battery

Removing the coin cell battery

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

cKeyboard

dBase cover

3 Removing the coin cell battery

a Use a plastic scribe to lift the battery out of the slot [1]

b Remove the battery [2]

26 Removing and installing components

Installing the coin cell battery

1 Insert the coin cell battery into the battery slot.

2 Press the battery until it clicks into place.

3 Install the:

aBasecover

bKeyboard

cOptical drive

dBattery

4 Follow the procedures in After working inside your computer.

Power button board

Removing the power button board

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

cKeyboard

dBase cover

3 To remove the power button board:

a Disconnect the system board cable from the computer [1].

b Remove the display hinge screws (M2.5x8) from the computer [2].

c Flip the display hinge to reveal the power button board beneath the hinge [3].

d Remove the 1 M2x2 (Big head07) screw that secures the power button board to the chassis [4].

e Peel the system board cable from the chassis and the peel the tape that holds the power button board.

f Slide the Power button board away from the chassis.

Removing and installing components 27

Installing the power button board

1 Place the button board on the chassis.

2 Ax the tape that holds the power button board.

3 Ax the system board cable to the chassis.

4 Place the power button board and tighten the screw.

5 Connect the system board cable to the power button board.

6 Tighten the screws to secure it to the power button board.

7 Install the:

aBase cover

bKeyboard

cOptical drive

dBattery

8 Follow the procedures in After working inside your computer.

Heat sink

Removing the heat sink

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

28 Removing and installing components

bOptical drive

cKeyboard

dBase cover

3 To remove the heat sink:

a Loosen the captive screws that secure the heat sink to the system board [1].

b Remove the heat sink from the system board [2].

Installing the heat sink

1 Align the screws on the heat sink with the screw holders on the system board.

2 Tighten the captive screws to secure it to the system board.

NOTE: Secure the screws in the order of the callout numbers [1, 2, 3, 4].

3 Install the:

aBase cover

bKeyboard

cOptical drive

dBattery

4 Follow the procedures in After working inside your computer.

System fan

Removing the system fan

1 Follow the procedure in Before working inside your computer.

2 Remove the:

Removing and installing components 29

aBattery

bOptical drive

cKeyboard

dBase cover

3 To remove the system fan:

a Disconnect the system fan connector cable from the system board [1].

b Remove the 2 (M2x5) screws that secure the system fan to the computer [2].

c Lift and remove the system fan from the chassis [3].

Installing the system fan

1 Align the system fan on the chassis.

2 Secure the system fan to the computer by tightening the 2 (M2x5) screws.

3 Connect the system fan connector cable to the system board connector.

4 Install the:

aBase cover

bKeyboard

cOptical drive

dBattery

5 Follow the procedures in After working inside your computer.

30 Removing and installing components

Speaker

Removing the speakers

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

cKeyboard

dBase cover

3 To remove the speakers:

a Disconnect the speaker cable from the computer [1].

b Remove the speaker cable from the retention clips on the computer [2].

c Remove the speakers from the computer [3].

Installing the speakers

1 Place the speakers into the slots on the computer.

2 Route the speaker cable through the retention clips on the computer.

3 Connect the speaker cable to the system board.

Removing and installing components 31

4 Install the:

aBase cover

bKeyboard

cOptical drive

dBattery

5 Follow the procedure in After working inside your computer

System board

Removing the system board

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

cKeyboard

dBase cover

eHard drive assembly

fWLAN card

gMemory module

hHeat sink

iSystem fan

3 Remove 1 (M2.5x8) screw and lift the display hinge from the chassis [1, 2].

32 Removing and installing components

4 Lift the locking tab to disconnect the following cables

a remove the adhesive tape [1]

b lift the locking tab and disconnect the eDP connector [1]

c power connector [2]

d hard drive connector [3]

engerprint connector [4]

f I/O connector [5]

g touchpad connector [6]

h speaker [7]

5 Remove 2 (M2x3) screw that secures the system board to the computer [1] and lift the system board [2].

Removing and installing components 33

6 Flip the system board.

7 To remove the system board:

a Peel the white adhesive tape and disconnect the power cable [1].

b Remove the system board from the computer [2].

34 Removing and installing components

Installing the system board

1 Connect the power cable.

2 Ax the white adhesive tape.

3 Flip the system board.

4 Align the system board with the screw holders on the computer.

5 Tighten the 2(M2x3) screw to secure the system board to the computer.

6 Tighten the display hinge 1 (M2.5x8) screw to the computer.

7 Connect the following cables to the system board.

a hard drive connector

b touchpad connector

c speaker connector

d I/O connector

e eDP connector

f power connector

gngerprint connector

8 Install the:

aSystem fan

bHeat sink

cMemory module

dWLAN Card

eHard drive assembly

fBase cover

gKeyboard

hOptical drive

Removing and installing components 35

iBattery

9 Follow the procedure in After working inside your computer.

Input/Output(I/O) boards

Removing the Input and Output board

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

cKeyboard

dBase cover

eHard drive assembly

3 To remove the Input/Output board (I/O board):

a Disconnect the I/O board cable [1].

b Remove 1 (M2x3) screw [2]

c Lift and remove the I/O board from the computer [3].

36 Removing and installing components

Installing the Input and Output board

1 Place the I/O board on the computer.

2 Connect the input/output (I/O board) cable and tighten the 1 (M2x3) screw.

3 Install the:

aHard drive assembly

bBase cover

cKeyboard

dOptical drive

eBattery

4 Follow the procedure in After working inside your computer.

Power connector port

Removing the power connector

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

cKeyboard

dBase cover

eHard drive assembly

fWLAN card

gMemory module

hHeat sink

iSystem fan

jCoin cell battery

kSystem board

3 To remove the power connector:

a Lift the cable from the slot [1].

b Remove the 1 (M2x3) screw that secures the power connector to the computer [2].

c Lift the power connector [3].

Removing and installing components 37

Installing the power connector

1 Insert the power connector into the slot on the computer.

2 Secure the power connector to the computer by using 1 (M2x3) screw.

3 Route the power connector cable into the slot.

4 Install the:

aSystem board

bCoin cell battery

cSystem fan

dWLAN Card

eMemory module

fHeat sink

gHard drive assembly

hBase cover

iKeyboard

jOptical drive

kBattery

5 Follow the procedure in After working inside your computer.

38 Removing and installing components

Display assembly

Removing the display assembly

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

cKeyboard

dBase cover

eHard drive assembly

fWLAN card

3 To remove the display assembly:

a Unroute the WLAN cable [1].

b Peel white adhesive tape [2].

c Lift the locking tab [3].

d Disconnect the eDP cable [4].

4 Flip the computer.

Removing and installing components 39

5 To remove the display assembly:

NOTE: Place the chassis on the edge of a table with the display facing down.

a Remove the 3 (M2.5x8) screws and lift the display hinge secured to the computer [1].

b Lift and remove the display assembly [2].

40 Removing and installing components

Installing the display assembly

1 Align the display assembly with the chassis.

2 Route the WLAN and display assembly cables through the cable-securing tabs.

3 Tighten the display hinges 3 (M2.5x8) screws to secure the display assembly.

4 Install the:

aWLAN Card

bHard drive assembly

cBase cover

dKeyboard

eOptical drive

fBattery

5 Follow the procedure in After working inside your computer.

Display bezel

NOTE: Non-touch display panel

Removing and installing components 41

Removing the display bezel

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

cKeyboard

dBase cover

eHard drive assembly

fWLAN card

gDisplay assembly

3 To disconnect the display bezel:

a Use a plastic scribe to release the tabs on the edges to release the display bezel from the display assembly.

b Remove the display bezel display assembly.

Installing the display bezel

1 Place the display bezel on the display assembly.

2 Press the display bezel on the edges until it snaps onto the display assembly.

3 Install the:

aDisplay assembly

bWLAN Card

cHard drive assembly

dBase cover

eKeyboard

42 Removing and installing components

fOptical drive

gBattery

4 Follow the procedure in After working inside your computer.

Camera

NOTE: Non-touch display panel

Removing the camera

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

cKeyboard

dBase cover

eHard drive assembly

fWLAN card

gDisplay assembly

hDisplay bezel

3 To remove the camera:

a Disconnect the camera cable from the camera [1].

b Remove the camera from the display assembly [2].

Removing and installing components 43

Installing the camera

1 Install the camera into the slot on the display assembly.

2 Connect the camera cable.

3 Install the:

aDisplay bezel

bDisplay assembly

cWLAN Card

dHard drive assembly

eBase cover

fKeyboard

gOptical drive

hBattery

4 Follow the procedure in After working inside your computer.

Display panel

NOTE: Non-touch display panel

Removing the display panel

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

cKeyboard

dBase cover

eHard drive assembly

fWLAN card

gDisplay assembly

hDisplay bezel

3 To remove the display panel:

a Remove the 4 (M2x3) screws that secure the display panel to the display assembly [1].

b Lift the display panel to access the cables underneath [2].

44 Removing and installing components

4 To disconnect the cable:

a Remove the tape that secures the eDP cable to the display panel [1].

b Lift the locking tab and remove the eDP cable [2].

c Remove the display panel from the computer [3].

Removing and installing components 45

Installing the display panel

1 Connect the eDP cable to the display panel.

2 Ax the tape to secure the display cable.

3 Place the display panel on the display assembly.

4 Tighten the 4 (M2x3) screws to secure the display panel to the display assembly.

5 Install the:

aDisplay bezel

bDisplay assembly

cWLAN Card

dHard drive assembly

eBase cover

fKeyboard

gOptical drive

hBattery

6 Follow the procedure in After working inside your computer.

Display hinges

NOTE: Non-touch display panel

Removing the display hinges

1 Follow the procedure in Before working inside your computer.

2 Remove the:

46 Removing and installing components

aBattery

bOptical drive

cKeyboard

dBase cover

eHard drive assembly

fWLAN card

gDisplay assembly

hDisplay bezel

iDisplay panel

3 To remove the hinges:

a Remove the 6 (M2.5x2.5) screws that secure the display hinges to the display assembly [1].

b Remove the display hinges [2].

Installing the display hinges

1 Tighten the 6 (M2.5x2.5) screws to secure the display hinges to the display assembly.

2 Install the:

aDisplay panel

bDisplay bezel

cDisplay assembly

dWLAN Card

eHard drive assembly

fBase cover

gKeyboard

hOptical drive

iBattery

3 Follow the procedure in After working inside your computer.

Removing and installing components 47

Touchpad

Removing the touchpad

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

cKeyboard

dBase cover

eHard drive assembly

fWLAN card

gMemory module

hSpeaker

iHeat sink

jSystem fan

kSystem board

3 Removing the screw support bracket.

a Remove the conductive tapes [1].

b Remove the three (M2x3) screws [2].

c Lift and remove the screw support bracket [3].

4 Removing the touchpad board.

a Remove the four (M2x2) screws [1].

b Lift and remove the touchpad board [2].

48 Removing and installing components

Installing the touchpad

1 Place the touchpad board into the slot.

2 Replace the four (M2xL2) screws that secure touchpad board.

3 Replace the three (M2xL3) screws and x the screw bracket.

4 Replace the conductive tapes.

5 Install the:

aSystem board

bSystem fan

cHeat sink

dSpeaker

eMemory module

fWLAN card

gHard drive assembly

hBase cover

iKeyboard

jOptical drive

kBattery

6 Follow the procedure in After working inside your computer.

Removing and installing components 49

Palm rest

Removing the palmrest

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aBattery

bOptical drive

cKeyboard

dBase cover

eHard drive assembly

fFingerprint reader

gWLAN card

hMemory module

iHeat sink

jSystem fan

kSystem board

lInput/Output boards

mDisplay assembly

NOTE: The component you are left with is the palmrest

3 Remove the palmrest assembly away from the computer.

50 Removing and installing components

Installing the palmrest

1 Place the palmrest on the computer.

2 Install the:

aDisplay assembly

bInput/Output boards

cSystem board

dSystem fan

eHeat sink

fMemory module

gWLAN Card

hFingerprint reader

iHard drive assembly

jBase cover

kKeyboard

lOptical drive

mBattery

3 Follow the procedure in After working inside your computer.

Removing and installing components 51

Technology and components

This chapter details the technology and components available in the system.

Topics:

• HDMI 1.4

• USB features

HDMI 1.4

This topic explains the HDMI 1.4 and its features along with the advantages.

HDMI (High-Denition Multimedia Interface) is an industry-supported, uncompressed, all-digital audio/video interface. HDMI provides an

interface between any compatible digital audio/video source, such as a DVD player, or A/V receiver and a compatible digital audio and/or

video monitor, such as a digital TV (DTV). The intended applications for HDMI TVs, and DVD players. The primary advantage is cable

reduction and content protection provisions. HDMI supports standard, enhanced, or high-denition video, plus multichannel digital audio on

a single cable.

NOTE: The HDMI 1.4 will provide 5.1 channel audio support.

HDMI 1.4 Features

•HDMI Ethernet Channel - Adds high-speed networking to an HDMI link, allowing users to take full advantage of their IP-enabled

devices without a separate Ethernet cable

•Audio Return Channel - Allows an HDMI-connected TV with a built-in tuner to send audio data "upstream" to a surround audio system,

eliminating the need for a separate audio cable

•3D - Denes input/output protocols for major 3D video formats, paving the way for true 3D gaming and 3D home theater applications

•Content Type - Real-time signaling of content types between display and source devices, enabling a TV to optimize picture settings

based on content type

•Additional Color Spaces - Adds support for additional color models used in digital photography and computer graphics

•4K Support - Enables video resolutions far beyond 1080p, supporting next-generation displays that will rival the Digital Cinema systems

used in many commercial movie theaters

•HDMI Micro Connector - A new, smaller connector for phones and other portable devices, supporting video resolutions up to 1080p

•Automotive Connection System - New cables and connectors for automotive video systems, designed to meet the unique demands of

the motoring environment while delivering true HD quality

Advantages of HDMI

• Quality HDMI transfers uncompressed digital audio and video for the highest, crispest image quality.

• Low -cost HDMI provides the quality and functionality of a digital interface while also supporting uncompressed video formats in a

simple, cost-eective manner

• Audio HDMI supports multiple audio formats from standard stereo to multichannel surround sound

• HDMI combines video and multichannel audio into a single cable, eliminating the cost, complexity, and confusion of multiple cables

currently used in A/V systems

• HDMI supports communication between the video source (such as a DVD player) and the DTV, enabling new functionality

52 Technology and components

USB features

Universal Serial Bus, or USB, was introduced in 1996. It dramatically simplied the connection between host computers and peripheral

devices like mice, keyboards, external drivers, and printers.

Let's take a quick look on the USB evolution referencing to the table below.

Table 2. USB evolution

Type Data Transfer Rate Category Introduction Year

USB 3.0/USB 3.1 Gen 1 5 Gbps Super Speed 2010

USB 2.0 480 Mbps High Speed 2000

USB 3.0/USB 3.1 Gen 1 (SuperSpeed USB)

For years, the USB 2.0 has been rmly entrenched as the de facto interface standard in the PC world with about 6 billion devices sold, and

yet the need for more speed grows by ever faster computing hardware and ever greater bandwidth demands. The USB 3.0/USB 3.1 Gen 1

nally has the answer to the consumers' demands with a theoretically 10 times faster than its predecessor. In a nutshell, USB 3.1 Gen 1

features are as follows:

• Higher transfer rates (up to 5 Gbps)

• Increased maximum bus power and increased device current draw to better accommodate power-hungry devices

• New power management features

• Full-duplex data transfers and support for new transfer types

• Backward USB 2.0 compatibility

• New connectors and cable

The topics below cover some of the most commonly asked questions regarding USB 3.0/USB 3.1 Gen 1.

Speed

Currently, there are 3 speed modes dened by the latest USB 3.0/USB 3.1 Gen 1 specication. They are Super-Speed, Hi-Speed and Full-

Speed. The new SuperSpeed mode has a transfer rate of 4.8Gbps. While the specication retains Hi-Speed, and Full-Speed USB mode,

commonly known as USB 2.0 and 1.1 respectively, the slower modes still operate at 480Mbps and 12Mbps respectively and are kept to

maintain backward compatibility.

USB 3.0/USB 3.1 Gen 1 achieves the much higher performance by the technical changes below:

• An additional physical bus that is added in parallel with the existing USB 2.0 bus (refer to the picture below).

• USB 2.0 previously had four wires (power, ground, and a pair for dierential data); USB 3.0/USB 3.1 Gen 1 adds four more for two pairs

of dierential signals (receive and transmit) for a combined total of eight connections in the connectors and cabling.

• USB 3.0/USB 3.1 Gen 1 utilizes the bidirectional data interface, rather than USB 2.0's half-duplex arrangement. This gives a 10-fold

increase in theoretical bandwidth.

Technology and components 53

With today's ever increasing demands placed on data transfers with high-denition video content, terabyte storage devices, high megapixel

count digital cameras etc., USB 2.0 may not be fast enough. Furthermore, no USB 2.0 connection could ever come close to the 480Mbps

theoretical maximum throughput, making data transfer at around 320Mbps (40MB/s) — the actual real-world maximum. Similarly, USB

3.0/USB 3.1 Gen 1 connections will never achieve 4.8Gbps. We will likely see a real-world maximum rate of 400MB/s with overheads. At this

speed, USB 3.0/USB 3.1 Gen 1 is a 10x improvement over USB 2.0.

Applications

USB 3.0/USB 3.1 Gen 1 opens up the laneways and provides more headroom for devices to deliver a better overall experience. Where USB

video was barely tolerable previously (both from a maximum resolution, latency, and video compression perspective), it's easy to imagine

that with 5-10 times the bandwidth available, USB video solutions should work that much better. Single-link DVI requires almost 2Gbps

throughput. Where 480Mbps was limiting, 5Gbps is more than promising. With its promised 4.8Gbps speed, the standard will nd its way

into some products that previously weren't USB territory, like external RAID storage systems.

Listed below are some of the available SuperSpeed USB 3.0/USB 3.1 Gen 1 products:

• External Desktop USB 3.0/USB 3.1 Gen 1 Hard Drives

• Portable USB 3.0/USB 3.1 Gen 1 Hard Drives

• USB 3.0/USB 3.1 Gen 1 Drive Docks & Adapters

• USB 3.0/USB 3.1 Gen 1 Flash Drives & Readers

• USB 3.0/USB 3.1 Gen 1 Solid-state Drives

• USB 3.0/USB 3.1 Gen 1 RAIDs

• Optical Media Drives

• Multimedia Devices

• Networking

• USB 3.0/USB 3.1 Gen 1 Adapter Cards & Hubs

Compatibility

The good news is that USB 3.0/USB 3.1 Gen 1 has been carefully planned from the start to peacefully co-exist with USB 2.0. First of all,

while USB 3.0/USB 3.1 Gen 1 species new physical connections and thus new cables to take advantage of the higher speed capability of

the new protocol, the connector itself remains the same rectangular shape with the four USB 2.0 contacts in the exact same location as

before. Five new connections to carry receive and transmitted data independently are present on USB 3.0/USB 3.1 Gen 1 cables and only

come into contact when connected to a proper SuperSpeed USB connection.

Windows 8/10 will be bringing native support for USB 3.1 Gen 1 controllers. This is in contrast to previous versions of Windows, which

continue to require separate drivers for USB 3.0/USB 3.1 Gen 1 controllers.

54 Technology and components

Microsoft announced that Windows 7 would have USB 3.1 Gen 1 support, perhaps not on its immediate release, but in a subsequent Service

Pack or update. It is not out of the question to think that following a successful release of USB 3.0/USB 3.1 Gen 1 support in Windows 7,

SuperSpeed support would trickle down to Vista. Microsoft has conrmed this by stating that most of their partners share the opinion that

Vista should also support USB 3.0/USB 3.1 Gen 1.

Super-Speed support for Windows XP is unknown at this point. Given that XP is a seven-year-old operating system, the likelihood of this

happening is remote.

Technology and components 55

System specications

Technical specications

This topics lists out the technical specications of your computer.

Table 3. Technical specication 3578

Model Number Vostro 3578

Processor family 8th generation Intel core processors (i5 and i7)

Operating System • Microsoft Windows 10 Home 64 bit

• Microsoft Windows 10 Professional 64 bit

• Microsoft Windows 10 National Academic 64-bit (Bid Desk)

• Ubuntu 16.04 LTS 64-bit

Memory DDR4 2400 MHz 2 slots supporting up to 16 GB

Chipset Integrated with the Processor

Graphics • Intel Integrated UHD 620 Graphics

• AMD Radeon 520 Graphics with 2GB GDDR5 vRAM

Display • 15.6 inches HD (1366x768) 220 nits, TN, Anti-Glare, Ultra-slim

• 15.6 inches AG, FHD(1920x1080), TN, eDP, at, Ultra-slim,

220nits

Storage options • 500 GB 5400RPM SATA hard drive

• 500 GB 7200RPM SATA hard drive

• 1 TB 5400RPM SATA hard drive

• 1 TB 7200RPM SATA hard drive

• 128 GB solid state drive (SSD)

• 256 GB solid state drive (SSD)

Multimedia • Integrated High Quality Speakers

• Universal Headphone Jack

• Integrated single digital microphone

• Integrated HD video webcam

Battery options 4-cell Lithium Ion (40 WHr)

• Length: 37.5 mm (1.47 inches)

• Width: 270.0 mm (10.63 inches)

• Weight: 0.25 kg (0.56 lb)

• Height: 20.0 mm (0.78 inch)

• Voltage: 14.8 VDC

Power adapter • E4 45W

56 System specications

Model Number Vostro 3578

• Input voltage: 100 to 240 VAC

• Input current (max): 1.3 A

• Input Frequency: 50 Hz to 60 Hz

• Output current: 2.31 A (continuous)

• Rated output voltage: 19.5 VDC

• Weight (kg): 0.27

• Dimensions (HxWxD inches): 0.87 x 2.6 x 4.17

• Temperature range: 0° to 40°C

• Operating: 32° to 104°F

• Storage:

-40° to 70°C

-40° to 158°F

• E4 65W

• Input voltage: 100 to 240 VAC

• Input current (max): 1.7 A

• Input Frequency: 50 Hz to 60 Hz

• Output current: 3.34 A (continuous)

• Rated output voltage: 19.5 VDC

• Weight (kg): 0.29

• Dimensions (HxWxD inches): 1.1 x 1.9 x 4.3

• Temperature range: 0° to 40°C

• Operating: 32° to 104°F

• Storage:

-40° to 70°C

-40° to 158°F

Connectivity 10/100/1000 Ethernet

• Wireless LAN Options:

• Qualcomm QCA9377 802.11ac Dual Band (1x1) Wireless

Adapter+ Bluetooth 4.1

• Qualcomm QCA61x4A 802.11ac Dual Band (2x2) Wireless

Adapter+ Bluetooth 4.1

Ports, Slots and Chassis • 2 USB 3.1 Gen 1 ports, 1 USB 2.0 port, HDMI 1.4, VGA

• RJ-45

• SD 3.0 Memory card reader

• Universal Jack (global headset jack + mic phone in)

• Optional Touch Fingerprint Reader

Input device Single Pointing, non backlit w/Precision compliant Clickpad

Touchpad (no buttons)

Regulatory and Environmental Compliance • ENERGY STAR 6.1 (includes Windows and Ubuntu OS)

• EPEAT Registered.

System specications 57

Table 4. 3578 Display specications

Display 15.6 – HD Non touch 15.6 – FHD Anti-glare Non touch

Type HD Anti-Glare FHD Anti-Glare

Luminance/Brightness (typical) HD 220nits FHD 220nits

Diagonal 15.6 inches 15.6 inches

Native Resolution HD 1366x768 FHD 1920x1080

Megapixels (millions of pixels) HD 1.05 FHD 2.07

Pixels per Inch (PPI) 101 for HD 141 for FHD

Contrast Ratio (min) 400:1 for HD 400:1 for FHD

Refresh Rate 60 Hz 60 Hz

Horizontal Viewing Angle HD +40/- 40 degrees FHD +40/- 40 degrees

Vertical Viewing Angle HD +10/- 30 degrees FHD +10/- 30 degrees

Pixel Pitch HD 0.252 mm FHD 0.179 mm

Power Consumption (max) HD 4.0 W FHD 3.7 W

Hot key combinations

Table 5. Hot key combinations

Fn key combination Function

Fn + ESC Fn toggle

Fn + F1 Speaker mute

Fn + F2 Volume down

Fn + F3 Volume up

Fn + F4 Rewind or play previous track

Fn + F5 Play or pause a track

Fn + F6 Forward or play next track

Fn + F8 Display toggle

Fn + F9 Search

Fn + F11 Panel brightness down

Fn + F12 Panel brightness up

58 System specications

System setup

System setup enables you to manage your notebook hardware and specify BIOS level options. From the System setup, you can:

• Change the NVRAM settings after you add or remove hardware

• View the system hardware conguration

• Enable or disable integrated devices

• Set performance and power management thresholds

• Manage your computer security

Topics:

• Boot Sequence

• Navigation keys

• System setup options

• Flashing the BIOS from the F12 One-Time boot menu

• Updating the BIOS in Windows

• System and setup password

Boot Sequence

Boot Sequence allows you to bypass the System Setup–dened boot device order and boot directly to a specic device (for example:

optical drive or hard drive). During the Power-on Self Test (POST), when the Dell logo appears, you can:

• Access System Setup by pressing F2 key

• Bring up the one-time boot menu by pressing F12 key

The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot menu options are:

• Removable Drive (if available)

• STXXXX Drive

NOTE: XXX denotes the SATA drive number.

• Optical Drive (if available)

• SATA Hard Drive (if available)

• Diagnostics

NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.

The boot sequence screen also displays the option to access the System Setup screen.

Navigation keys

NOTE: For most of the System Setup options, changes that you make are recorded but do not take eect until you restart the

system.

Keys Navigation

Up arrow Moves to the previous eld.

System setup 59

Keys Navigation

Down arrow Moves to the next eld.

Enter Selects a value in the selected eld (if applicable) or follow the link in the eld.

Spacebar Expands or collapses a drop‐down list, if applicable.

Tab Moves to the next focus area.

NOTE: For the standard graphics browser only.

Esc Moves to the previous page until you view the main screen. Pressing Esc in the main screen displays a message

that prompts you to save any unsaved changes and restarts the system.

System setup options

NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not appear.

Table 6. General tab

Option Description

System Information This section lists the primary hardware features of your computer.

• System Information: Displays BIOS Version, Service Tag, Asset Tag, Ownership Tag, Manufacture Date,

Ownership Date, and the Express Service Code.

• Memory Information: Displays Memory Installed, Memory Available, Memory Speed, Memory Channels Mode,

Memory Technology, DIMM A Size, and DIMM B Size

• Processor Information: Displays Processor Type, Core Count, Processor ID, Current Clock Speed, Minimum

Clock Speed, Maximum Clock Speed, Processor L2 Cache, Processor L3 Cache, HT Capable, and 64-Bit

Technology.

• Device Information: SATA-0, SATA-1, LOM MAC Address, Video Controller, dGPU Video Controller, Video

BIOS Version, Video Memory, Panel Type, Native Resolution, Audio Controller, Wi-Fi Device, Bluetooth Device.

Battery Information Displays the battery status and the type of AC adapter connected to the computer.

Boot Sequence Boot Sequence Allows you to change the order in which the computer

attempts to nd an operating system. The option is:

• Windows Boot Manager

By default, all the options are checked. You can also

deselect any option or change the boot order.

Boot List Option Allows you to change the boot list option.

• Legacy

• UEFI (Selected by default)

Advanced Boot

Options

This option allows you the legacy option ROMs to load.

• Enable Legacy Option ROMs

• Enable Attempt Legacy Boot

By default, the Enable Legacy Option ROMs option is enabled.

UEFI Boot Path

Security

These options control whether or not the system will prompt the user to enter the Admin password (if set) when

booting a UEFI boot path from the F12 Boot Menu.

• Always, Except Internal HDD

• Always

• Never

60 System setup

Option Description

By default, Always, Except Internal HDD is enabled.

Date/Time Allows you to change the date and time.

Table 7. System Conguration

Option Description

Integrated NIC Allows you to congure the integrated network controller. The options are:

• Disabled

• Enabled

• Enabled w/PXE: This option is enabled by default.

SATA Operation Allows you to congure the internal SATA hard-drive controller. The options are:

• Disabled

• AHCI: This option is enabled by default.

Drives Allows you to congure the SATA drives on board. All drives are enabled by default. The options

are:

• SATA-0: This option is selected by default.

• SATA-1: This option is selected by default.

SMART Reporting This eld controls whether hard drive errors for integrated drives are reported during system

startup. This technology is part of the SMART (Self-Monitoring Analysis and Reporting

Technology) specication. This option is disabled by default.

• Enable SMART Reporting

USB Conguration This eld congures the integrated USB controller. If Boot Support is enabled, the system is

allowed to boot any type of USB Mass Storage Devices (HDD, memory key, oppy).

If USB port is enabled, device attached to this port is enabled and available for OS.

If USB port is disabled, the OS cannot see any device attached to this port.

• Enable Boot Support: This option is selected by default.

• Enable External USB Port: This option is selected by default.

NOTE: USB keyboard and mouse always work in the BIOS setup irrespective of these

settings.

Audio This eld enables or disables the integrated audio controller. The options are:

• Enable Microphone

• Enable Internal Speaker

NOTE: All devices are enabled by default.

Miscellaneous Devices Allows you to enable or disable the following devices:

• Enable Camera

• Enabled Secure Digital (SD) Card

NOTE: All devices are enabled by default.

System setup 61

Table 8. Video

Option Description

LCD Brightness Allows you to set the display brightness depending up on the power source (On Battery and On

AC).

NOTE: The Video setting will only be visible when a video card is installed into the

system.

Table 9. Security

Option Description

Admin Password Allows you to set, change, or delete the administrator (admin) password.

NOTE: You must set the admin password before you set the system or hard drive

password. Deleting the admin password automatically deletes the system password

and the hard drive password.

NOTE: Successful password changes take eect immediately.

Default Setting: Not set

System Password Allows you to set, change or delete the system password.

NOTE: Successful password changes take eect immediately.

Default Setting: Not set

Internal HDD-0 Password Allows you to set, change or delete the password on the system's internal hard-disk drive.

NOTE: Successful password changes take eect immediately.

Default Setting: Not set

Strong Password Allows you to enforce the option to always set strong passwords.

Default Setting: Enable Strong Password is not selected.

NOTE: If Strong Password is enabled, Admin and System passwords must contain at

least one uppercase character, one lowercase character and be at least 8 characters

long.

Password Conguration Allows you to determine the minimum and maximum length of Administrator and System

passwords.

Password Bypass Allows you to enable or disable the permission to bypass the System and the Internal HDD

password, when they are set. The options are:

• Disabled

• Reboot bypass

Default Setting: Disabled

Password Change Allows you to enable the disable permission to the System and Hard Drive passwords when the

admin password is set.

Default Setting: Allow Non-Admin Password Changes is selected.

Non-Admin Setup Changes Allows you to determine whether changes to the setup options are allowed when an

Administrator Password is set. If disabled the setup options are locked by the admin password.

UEFI Capsule Firmware Updates Allows you to controls whether the system allows BIOS update via UEFI capsule update

packages. Default setting: Enable

62 System setup

Option Description

TPM 2.0 Security Allows you to enable the Trusted Platform Module (TPM) during POST. The options are:

• TPM On (enabled by default)

• Clear

• PPI Bypass for Enabled Commands

• PPI Bypass for Disabled Commands

• Attestation Enable (enabled by default)

• Key Storage Enable (enabled by default)

• SHA-256 (enabled by default)

• Disabled

• Enabled

NOTE: To upgrade or downgrade TPM1.2/2.0, download the TPM wrapper tool

(software).

Computrace Allows you to activate or disable the optional Computrace software The options are:

• Deactivate

• Disable

• Activate

NOTE: The Activate and Disable options will permanently activate or disable the

feature and no further changes will be allowed.

Default setting: Deactivate

CPU XD Support Allows you to enable the Execute Disable mode of the processor.

Enable CPU XD Support (default)

Admin Setup Lockout Allows you to prevent users from entering Setup when an Administrator password is set.

Default Setting: Enable Admin Setup Lockout is not selected.

Master Password Lockout When enabled, this option will disable master password support.

• Enable Master Password Lockout

Default setting: Enable Master Password Lockout is disabled

SMM Security Mitigation This option enables or disables additional UEFI SMM Security Mitigation protections.

• Enable Master Password Lockout

Default setting: SMM Security Mitigation is disabled

Table 10. Secure Boot

Option Description

Secure Boot Enable This option enables or disables the Secure Boot Feature.

• Disabled

• Enabled

Default Setting: The option is disabled.

Expert Key Management Allows you to manipulate the security key databases only if the system is in Custom Mode. The

Enable Custom Mode option is disabled by default. The options are:

• PK

System setup 63

Option Description

• KEK

• db

• dbx

If you enable the Custom Mode, the relevant options for PK, KEK, db, and dbx appear. The

options are:

•Save to File- Saves the key to a user-selected le

•Replace from File- Replaces the current key with a key from a user-selected le

•Append from File- Adds a key to the current database from a user-selected le

•Delete- Deletes the selected key

•Reset All Keys- Resets to default setting

•Delete All Keys- Deletes all the keys

NOTE: If you disable the Custom Mode, all the changes made will be erased and the

keys will restore to default settings.

Table 11. Intel Software Guard Extensions screen options

Option Description

Intel SGX Enable This eld species you to provide a secured environment for

running code/storing sensitive information in the context of the

main OS. The options are:

• Disabled

• Enabled

• Software Controlled

Default setting: Software Controlled

Enclave Memory Size This option sets SGX Enclave Reserve Memory Size. The options

are:

• 32 MB

• 64 MB

• 128 MB

Default setting: 128 MB

Table 12. Performance

Option Description

Multi Core Support This eld species whether the process will have one or all cores enabled. The performance of

some applications will improve with the additional cores. This option is enabled by default. Allows

you to enable or disable multi-core support for the processor. The installed processor supports

two cores. If you enable Multi Core Support, two cores will be enabled. If you disable Multi Core

Support, one core will be enabled.

Multi Core Support

• All

• 1

• 2

• 3

64 System setup

Option Description

Default Setting: All is enabled.

Intel SpeedStep Allows you to enable or disable the Intel SpeedStep feature.

• Enable Intel SpeedStep

Default Setting: The option is enabled.

C States Control Allows you to enable or disable the additional processor sleep states.

• C states

Default Setting: The option is enabled.

Intel TurboBoost Allows you to enable or disable the Intel TurboBoost mode of the processor.

• Enable Intel TurboBoost

Default Setting: The option is enabled.

Hyper-Thread Control Allows you to enable or disable the HyperThreading in the processor.

• Disabled

• Enabled

Default Setting: The option is enabled.

Table 13. Power Management

Option Description

AC Behavior Allows you to enable or disable the computer from turning on automatically when an AC adapter

is connected.

Default Setting: Wake on AC is not selected.

Enable Intel Speed Shift Technology This option is used to enable/disable Intel Speed Shift Technology support. Setting this option to

enable allows the operating system to select the appropriate processor performance

automatically.

Default Setting: Enable Intel Speed Shift Technology is enabled.

Auto On Time Allows you to set the time at which the computer must turn on automatically. The options are:

• Disabled (default)

• Every Day

• Weekdays

• Select Days

USB Wake Support Allows you to enable USB devices to wake the system from Standby.

NOTE: This feature is only functional when the AC power adapter is connected. If the

AC power adapter is removed during Standby, the system setup will remove power

from all of the USB ports to conserve battery power.

• Enable USB Wake Support

Default Setting: The option is disabled.

Wake on LAN Allows you to enable or disable the feature that powers on the computer from the O state

when triggered by a LAN signal.

System setup 65

Option Description

• Disabled: This option is enabled by default

• LAN Only

Advanced Battery Charge

Conguration

Advanced Battery Charge maximizes battery health while still supporting heavy use during work

day.

Primary Battery Charge Conguration Allows you to select the charging mode for the battery. The options are:

• Adaptive

• Standard — Fully charges your battery at a standard rate.

• Primarily AC use

• Custom

If Custom Charge is selected, you can also congure Custom Charge Start and Custom Charge

Stop.

Default Setting: The option Adaptive is enabled.

NOTE: All charging mode may not be available for all the batteries. To enable this

option, disable the Advanced Battery Charge Conguration option.

Table 14. POST Behavior

Option Description

Adapter Warnings Allows you to enable or disable the system setup (BIOS) warning messages when you use

certain power adapters.

Default Setting: Enable Adapter Warnings

Numlock Enable This option species whether the Numlock function should be enable when the system boots.

• Enable Numlock. (Enabled by default).

Fn Lock Option Allows the hot key combination <Fn> +<Esc> toggle the primary behavior of F1–F12, between

the standard and secondary functions.

• Lock Mode Disable/Standard.

• Lock Mode Enable/Secondary. This option is enabled by default.

Fastboot Allows you to speed up the boot process by bypassing some of the compatibility steps. The

options are:

• Minimal

• Thorough (default)

• Auto

Extended BIOS POST Time Allows you to create an additional preboot delay. The options are:

• 0 seconds. This option is enabled by default.

• 5 seconds

• 10 seconds

Full Screen Logo This option will display full screen logo if your image match screen resolution.

Default Setting: Enable Full Screen Logo is disabled

Warnings and Logo The Warning and Errors option cause the boot process to only pause when warnings or errors

are detected, rather than stop, prompt and wait for user input.

• Prompt on Warnings and Errors (enabled).

66 System setup

Option Description

• Continue on Warnings

• Continue on Warnings and Errors

Table 15. Virtualization Support

Option Description

Virtualization Allows you to enable or disable the Intel Virtualization Technology.

•Enable Intel Virtualization Technology (default)

VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the additional hardware

capabilities provided by Intel® Virtualization technology for direct I/O.

Enable VT for Direct I/O — enabled by default.

Table 16. Wireless

Option Description

Wireless Switch Allows to set the wireless devices that can be controlled by the

wireless switch. The options are:

• WLAN

• Bluetooth

All the options are enabled by default.

Wireless Device Enable Allows you to enable or disable the internal wireless devices.

• WLAN

• Bluetooth

All the options are enabled by default.

Table 17. Maintenance

Option Description

Service Tag Displays the Service Tag of your computer.

Asset Tag Allows you to create a system asset tag if an asset tag is not already set. This option is not set

by default.

BIOS Downgrade This eld controls ashing of the system rmware to pervious revisions.

Allows BIOS Downgrade (Enabled by default)

Data Wipe This eld enables user to erase data from all internal storage device.

BIOS Recovery Allows you to recover from certain corrupted BIOS conditions from a recover le on the user

primary hard drive or an external USB key. Enabled by default.

System setup 67

Table 18. System Logs

Option Description

BIOS Events Allows you to view and clear the System Setup (BIOS) POST events.

Thermal Events Allows you to view and clear the System Setup (Thermal) POST events.

Power Events Allows you to view and clear the System Setup (Power) POST events.

Table 19. SupportAssist System Resolution

Option Description

Auto OS Recovery Threshold Allows you to control the automatic boot ow for SupportAssist System. Options are:

•O

• 1

• 2 (Enabled by default)

• 3

SupportAssist OS Recovery Allows you to recover the SupportAssist OS Recovery (Disabled by default)

Flashing the BIOS from the F12 One-Time boot menu

Updating your system BIOS using a BIOS update .exe le copied to a FAT32 USB key and booting from the F12 one time boot menu.

BIOS Update

You can run the BIOS update le from Windows using a bootable USB key or you can also update the BIOS from the F12 One-Time boot

menu on the system.

Most Dell systems built after 2012 have this capability and you can conrm by booting your system to the F12 One-Time Boot Menu to see

if BIOS FLASH UPDATE is listed as a boot option for your system. If the option is listed, then the BIOS supports this BIOS update option.

NOTE: Only systems with BIOS Flash Update option in the F12 One-Time Boot Menu can use this function.

Updating from the One-Time Boot Menu

To update your BIOS from the F12 One-Time boot menu, you will need:

• USB key formatted to the FAT32 le system (key does not have to be bootable)

• BIOS executable le that you downloaded from the Dell Support website and copied to the root of the USB key

• AC power adapter connected to the system

• Functional system battery to ash the BIOS

Perform the following steps to execute the BIOS update ash process from the F12 menu:

CAUTION: Do not power o the system during the BIOS update process. Powering o the system could make the system fail to

boot.

1 From a power o state, insert the USB key where you copied the ash into a USB port of the system .

2 Power on the system and press the F12 key to access the One-Time Boot Menu, Highlight BIOS Flash Update using the arrow keys

then press Enter.

68 System setup

3 The Bios ash menu will open then click the browse button.

4 The E5450A14.exe le is shown as an example in the following screenshot. The actual le name may vary.

System setup 69

5 Once the le is selected, it will show in the le selection box and you can click the OK button to continue.

6 Click the Begin Flash Update button.

70 System setup

7 A warning box is displayed asking you if you want to proceed. Click the Yes button to begin the ash.

8 At this point the BIOS ash will execute, the system will reboot and then the BIOS ash will start and a progress bar will show the

progress of the ash. Depending on the changes included in the update, the progress bar may go from zero to 100 multiple times and

the ash process could take as long as 10 minutes. Generally this process takes two to three minutes.

System setup 71

9 Once complete, the system will reboot and the BIOS update process is completed.

Updating the BIOS in Windows

It is recommended to update your BIOS (System Setup), when you replace the system board or if an update is available. For laptops, ensure

that your computer battery is fully charged and connected to a power outlet

NOTE: If BitLocker is enabled, it must be suspended prior to updating the system BIOS, and then re-enabled after the BIOS

update is completed.

1 Restart the computer.

2 Go to Dell.com/support.

• Enter the Service Tag or Express Service Code and click Submit.

• Click Detect Product and follow the instructions on screen.

3 If you are unable to detect or nd the Service Tag, click Choose from all products.

4 Choose the Products category from the list.

NOTE: Choose the appropriate category to reach the product page

5 Select your computer model and the Product Support page of your computer appears.

6 Click Get drivers and click Drivers and Downloads.

The Drivers and Downloads section opens.

7 Click Find it myself.

8 Click BIOS to view the BIOS versions.

9 Identify the latest BIOS le and click Download.

10 Select your preferred download method in the Please select your download method below window, click Download File.

The File Download window appears.

11 Click Save to save the le on your computer.

12 Click Run to install the updated BIOS settings on your computer.

Follow the instructions on the screen.

NOTE: It is recommended not to update the BIOS version for more than three revisions. For example: If you want to update the

BIOS from 1.0 to 7.0, then install version 4.0 rst and then install version 7.0.

72 System setup

System and setup password

You can create a system password and a setup password to secure your computer.

Password type Description

System password Password that you must enter to log on to your system.

Setup password Password that you must enter to access and make changes to the BIOS settings of your computer.

CAUTION: The password features provide a basic level of security for the data on your computer.

CAUTION: Anyone can access the data stored on your computer if it is not locked and left unattended.

NOTE: System and setup password feature is disabled.

Assigning a system password and setup password

You can assign a new System Password only when the status is in Not Set.

To enter the system setup, press F2 immediately after a power-on or re-boot.

1 In the System BIOS or System Setup screen, select Security and press Enter.

The Security screen is displayed.

2 Select System Password and create a password in the Enter the new password eld.

Use the following guidelines to assign the system password:

• A password can have up to 32 characters.

• The password can contain the numbers 0 through 9.

• Only lower case letters are valid, upper case letters are not allowed.

• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

3 Type the system password that you entered earlier in the Conrm new password eld and click OK.

4 Press Esc and a message prompts you to save the changes.

5 Press Y to save the changes.

The computer reboots.

Deleting or changing an existing system and or setup password

Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing System and/or

Setup password. You cannot delete or change an existing System or Setup password, if the Password Status is Locked.

To enter the System Setup, press F2 immediately after a power-on or reboot.

1 In the System BIOS or System Setup screen, select System Security and press Enter.

The System Security screen is displayed.

2 In the System Security screen, verify that Password Status is Unlocked.

3 Select System Password, alter or delete the existing system password and press Enter or Tab.

4 Select Setup Password, alter or delete the existing setup password and press Enter or Tab.

NOTE: If you change the System and/or Setup password, re-enter the new password when promoted. If you delete the

System and/or Setup password, conrm the deletion when promoted.

5 Press Esc and a message prompts you to save the changes.

6 Press Y to save the changes and exit from System Setup.

The computer reboots.

System setup 73

Software

This chapter details the supported operating systems along with instructions on how to install the drivers.

Topics:

• Supported operating systems

• Downloading drivers

• Intel chipset drivers

• Battery drivers

• Intel HID Event Filter

• Intel Dynamic Platform and Thermal Framework

• Disk drivers

• Realtek PCI-E Memory Card

• Graphics controller driver

• Bluetooth drivers

• Network drivers

• Realtek Audio

• Storage drivers

• Security drivers

Supported operating systems

Table 20. Supported operating systems

Supported operating systems Description

Windows 10 • Microsoft Windows 10 Pro 64-bit

• Microsoft Windows 10 Home 64-bit

Downloading drivers

1 Turn on the notebook.

2 Go to Dell.com/support.

3 Click Product Support, enter the Service Tag of your notebook, and then click Submit.

NOTE: If you do not have the Service Tag, use the auto detect feature or manually browse for your notebook model.

4 Click Drivers and Downloads.

5 Select the operating system installed on your notebook.

6 Scroll down the page and select the driver to install.

7 Click Download File to download the driver for your notebook.

8 After the download is complete, navigate to the folder where you saved the driver le.

9 Double-click the driver le icon and follow the instructions on the screen.

74 Software

Intel chipset drivers

Verify if the Intel chipset drivers are already installed in the system.

Table 21. Intel chipset drivers

Before Installation After Installation

Software 75

Battery drivers

The latest battery drivers are installed in the computer.

Table 22. Battery drivers

Before Installation After Installation

Intel HID Event Filter

Verify if the Intel HID event lter is already installed in the computer.

Table 23. Intel HID Event Filter

Before Installation After Installation

76 Software

Intel Dynamic Platform and Thermal Framework

Verify if the Intel dynamic platform and thermal framework is already installed in the computer.

Table 24. Intel Dynamic Platform and Thermal Framework

Before Installation After Installation

Disk drivers

Disk drivers installed in the system

Table 25. Disk drivers

Before Installation After Installation

None

Realtek PCI-E Memory Card

Verify if the Realtek PCI-E Memory Card is already installed in the computer.

Table 26. Realtek PCI-E memory card

Before Installation After Installation

Graphics controller driver

Verify if the graphics controller driver is already installed in the computer.

Software 77

Table 27. Graphics controller driver

Before Installation After Installation

Bluetooth drivers

This platform supports a variety of Bluetooth drivers. The following is an example

Table 28. Bluetooth drivers

Before Installation After Installation

Network drivers

Install the WLAN and Bluetooth drivers from the Dell support site.

Table 29. Network drivers

Before installation After installation

Realtek Audio

Verify if audio drivers are already installed in the computer.

78 Software

Table 30. Realtek audio

Before Installation After Installation

Storage drivers

Verify if the storage controller drivers are installed in the system.

Table 31. Storage drivers

Before Installation After Installation

None

Security drivers

Verify if the security device drivers are installed in the computer.

Table 32. Security drivers

Before Installation After Installation

None

Software 79

Troubleshooting

Enhanced Pre-Boot System Assessment — ePSA

diagnostics

The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware. The ePSA is embedded with the

BIOS and is launched by the BIOS internally. The embedded system diagnostics provides a set of options for particular devices or device

groups allowing you to:

• Run tests automatically or in an interactive mode

• Repeat tests

• Display or save test results

• Run thorough tests to introduce additional test options to provide extra information about the failed device(s)

• View status messages that inform you if tests are completed successfully

• View error messages that inform you of problems encountered during testing

CAUTION: Use the system diagnostics to test only your computer. Using this program with other computers may cause invalid

results or error messages.

NOTE: Some tests for specic devices require user interaction. Always ensure that you are present at the computer terminal

when the diagnostic tests are performed.

Running the ePSA diagnostics

1 Power-on the computer.

2 As the computer boots, press the F12 key as the Dell logo appears.

3 On the boot menu screen, select the Diagnostics option.

4 Click the arrow key at the bottom left corner.

Diagnostics front page is displayed.

5 Press the arrow in the lower-right corner to go to the page listing.

The items detected are listed.

6 To run a diagnostic test on a specic device, press Esc and click Yes to stop the diagnostic test.

7 Select the device from the left pane and click Run Tests.

8 If there are any issues, error codes are displayed.

Note the error code and validation number and contact Dell.

Diagnostic LED

This section details the diagnostic features of the battery LED in a notebook.

Instead of beep codes errors are indicated via the bicolor Battery Charge LED. A specic blink pattern is followed by ashing a pattern of

ashes in amber, followed by white. The pattern then repeats.

NOTE: The diagnostic pattern will consist of a two digit number being represented by a rst group of LED blinks (1 through 9) in

amber, followed by a 1.5 second pause with the LED o, and then a second group of LED blinks (1 through 9) in white. This is

then followed by a three second pause, with the LED o, before repeating over again. Each LED blink takes 0.5 seconds.

80 Troubleshooting

The system will not shutdown when displaying the Diagnostic Error Codes. Diagnostic Error Codes will always supersede any other use of

the LED. For instance, on Notebooks, battery codes for Low Battery or Battery Failure situations will not be displayed when Diagnostic

Error Codes are being displayed:

Table 33. LED pattern

Blinking pattern Problem Description Suggested Resolution

Amber White

2 1 processor processor failure

2 2 system board, BIOS ROM system board, covers BIOS corruption or ROM error

2 3 memory no memory/no RAM detected

2 4 memory memory failure/RAM failure

2 5 memory invalid memory installed

2 6 system board; chipset system board/ chipset error

2 7 display display failure

3 1 RTC power failure coin-cell battery failure

3 2 PCI/Video PCI/Video card/chip failure

3 3 BIOS recovery 1 recovery image nor found

3 4 BIOS recovery 2 recovery image found but invalid

Real Time Clock reset

The Real Time Clock (RTC) reset function allows you or the service technician to recover the recently launched model Dell Latitude and

Precision systems from select No POST/No Boot/No Power situations. You can initiate the RTC reset on the system from a power o

state only if it is connected to AC power. Press and hold the power button for 25 seconds. The system RTC reset occurs after you release

the power button.

NOTE: If AC power is disconnected from the system during the process or the power button is held longer than 40 seconds, the

RTC reset process is aborted.

The RTC reset will reset the BIOS to Defaults, un-provision Intel vPro and reset the system date and time. The following items are

unaected by the RTC reset:

• Service Tag

• Asset Tag

• Ownership Tag

• Admin Password

• System Password

• HDD Password

• Key Databases

• System Logs

The following items may or may not reset based on your custom BIOS setting selections:

• The Boot List

• Enable Legacy OROMs

• Secure Boot Enable

Troubleshooting 81

• Allow BIOS Downgrade

82 Troubleshooting

Contacting Dell

NOTE: If you do not have an active Internet connection, you can nd contact information on your purchase invoice, packing slip,

bill, or Dell product catalog.

Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services

may not be available in your area. To contact Dell for sales, technical support, or customer service issues:

1 Go to Dell.com/support.

2 Select your support category.

3 Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.

4 Select the appropriate service or support link based on your need.

Contacting Dell 83

Table of Contents

DELL 3578 User Manual

Related Manuals