DELL 3800 User Manual

Displayed below is the user manual for 3800 by DELL which is a product in the PCs/Workstations category. This manual has pages.

Related Manuals

DELL 3800 Manual

Dell Vostro 3800

Owner's Manual

Regulatory Model: D08D

Regulatory Type: D08D001

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other

jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.

2014 - 06

Rev. A01

Contents

1 Working on Your Computer...................................................................................5

Before Working Inside Your Computer................................................................................................ 5

Turning Off Your Computer..................................................................................................................6

After Working Inside Your Computer................................................................................................... 7

2 Removing and Installing Components................................................................8

Recommended Tools............................................................................................................................8

System Overview...................................................................................................................................8

Inside view ...................................................................................................................................... 8

Removing The Cover............................................................................................................................ 9

Installing The Cover.............................................................................................................................. 9

Removing The Bezel............................................................................................................................. 9

Installing The Bezel............................................................................................................................. 10

Removing The Optical Drive...............................................................................................................10

Installing The Optical Drive................................................................................................................. 11

Removing The Hard Drive................................................................................................................... 11

Installing The Hard Drive.....................................................................................................................12

Removing the Expansion Card(s)........................................................................................................13

Installing the Expansion Card(s)..........................................................................................................13

Removing The Power Supply Unit (PSU)............................................................................................ 13

Installing The Power Supply Unit (PSU).............................................................................................. 15

Removing The Heatsink...................................................................................................................... 15

Installing The Heatsink........................................................................................................................ 16

Removing the Processor.....................................................................................................................16

Installing the Processor.......................................................................................................................16

Removing the Memory........................................................................................................................16

Installing the Memory..........................................................................................................................17

Removing The System Fan..................................................................................................................17

Installing The System Fan....................................................................................................................18

Removing The Input/Output (I/O) Panel............................................................................................18

Installing The Input/Output (I/O) Panel..............................................................................................19

Removing The System Board............................................................................................................. 20

Installing The System Board................................................................................................................21

System Board Components................................................................................................................ 21

3 Troubleshooting Your Computer.......................................................................23

Diagnostic Power LED Codes.............................................................................................................23

Diagnostic Error Messages................................................................................................................. 24

System Error Messages....................................................................................................................... 28

4 System Setup........................................................................................................... 29

System Setup Overview...................................................................................................................... 29

Enter System Setup............................................................................................................................. 29

System Setup Options.........................................................................................................................29

Main............................................................................................................................................... 29

Advanced.......................................................................................................................................30

Boot................................................................................................................................................31

Power.............................................................................................................................................32

Security.......................................................................................................................................... 32

Exit..................................................................................................................................................32

5 Specifications...........................................................................................................33

6 Contacting Dell....................................................................................................... 37

Working on Your Computer

Before Working Inside Your Computer

Use the following safety guidelines to help protect your computer from potential damage and to help to

ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes

that the following conditions exist:

• You have read the safety information that shipped with your computer.

• A component can be replaced or--if purchased separately--installed by performing the removal

procedure in reverse order.

WARNING: Disconnect all power sources before opening the computer cover or panels. After you

finish working inside the computer, replace all covers, panels, and screws before connecting to

the power source.

WARNING: Before working inside your computer, read the safety information that shipped with

your computer. For additional safety best practices information, see the Regulatory Compliance

Homepage at www.dell.com/regulatory_compliance

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or

by periodically touching an unpainted metal surface, such as a connector on the back of the

computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts

on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a

processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable

itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable,

press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep

them evenly aligned to avoid bending any connector pins. Also, before you connect a cable,

ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear differently than shown in

this document.

To avoid damaging your computer, perform the following steps before you begin working inside the

computer.

1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

2. Turn off your computer (see Turning Off Your Computer).

CAUTION: To disconnect a network cable, first unplug the cable from your computer and

then unplug the cable from the network device.

3. Disconnect all network cables from the computer.

4. Disconnect your computer and all attached devices from their electrical outlets.

5. Press and hold the power button while the computer is unplugged to ground the system board.

6. Remove the cover.

CAUTION: Before touching anything inside your computer, ground yourself by touching an

unpainted metal surface, such as the metal at the back of the computer. While you work,

periodically touch an unpainted metal surface to dissipate static electricity, which could

harm internal components.

Turning Off Your Computer

CAUTION: To avoid losing data, save and close all open files and exit all open programs before

you turn off your computer.

1. Shut down the operating system:

• In Windows 8:

– Using a touch-enabled device:

a. Swipe in from the right edge of the screen, opening the Charms menu and select

Settings.

b. Select the and then select Shut down

– Using a mouse:

a. Point to upper-right corner of the screen and click Settings.

b. Click the and select Shut down.

• In Windows 7:

1. Click Start .

2. Click Shut Down.

1. Click Start .

2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click

Shut Down..

2. Ensure that the computer and all attached devices are turned off. If your computer and attached

devices did not automatically turn off when you shut down your operating system, press and hold

the power button for about 6 seconds to turn them off.

After Working Inside Your Computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and

cables before turning on your computer.

1. Replace the cover.

CAUTION: To connect a network cable, first plug the cable into the network device and then

plug it into the computer.

2. Connect any telephone or network cables to your computer.

3. Connect your computer and all attached devices to their electrical outlets.

4. Turn on your computer.

5. If required, verify that the computer works correctly by running the Dell Diagnostics.

Removing and Installing Components

This section provides detailed information on how to remove or install the components from your

computer.

Recommended Tools

The procedures in this document may require the following tools:

• Small flat-blade screwdriver

• Phillips screwdriver

• Small plastic scribe

System Overview

Inside view

1. heatsink fan 2. memory module

3. system board 4. optical drive

5. I/O panel 6. system fan

7. hard drive 8. coin-cell battery

9. power supply unit (PSU) 10. expansion card

Removing The Cover

1. Follow the procedures in Before Working Inside Your Computer.

2. Follow the steps below to remove the cover:

a. Remove the screws that secure the cover to the computer.

b. Lift and remove the cover from the computer.

Installing The Cover

1. Place the cover on the chassis.

2. Replace the screws to secure the cover to the computer.

3. Follow the procedures in After Working Inside Your Computer.

Removing The Bezel

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the cover.

3. Follow the steps below to remove the bezel:

a. Pry the front panel retention clips away from the chassis.

b. Release the hooks on the opposite edge of the bezel from the chassis.

c. Remove the bezel from the computer.

Installing The Bezel

1. Place the hooks on the notches in the computer.

2. Rotate the front bezel towards the compute .

3. Press the front bezel till the tabs snap in to place.

4. Install the cover.

5. Follow the procedures in After Working Inside Your Computer.

Removing The Optical Drive

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the:

• cover

• bezel

3. Follow the steps below to remove the optical drive:

a. Disconnect the data cable and power cable from the optical drive [1,2].

b. Pull the optical-drive release latch and then push the optical drive towards the front of the

computer [3].

c. Remove the optical drive from the computer [4].

Installing The Optical Drive

1. Push the optical drive into the computer till it snaps into place.

2. Connect the data cable and power cable to the optical drive.

3. Install the:

• bezel

• cover

4. Follow the procedures in After Working Inside Your Computer.

Removing The Hard Drive

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the:

• cover

• bezel

3. Follow the steps below to remove the hard-drive bracket:

a. Disconnect the SATA cable and power cable from the hard drive [1,2].

b. Push the blue tab on the hard-drive bracket and lift it to remove it from the computer [3,4].

4. Follow the steps below to remove the hard drive from the hard-drive bracket:

a. Pry along the retention tabs of the hard-drive bracket to loosen it.

b. Lift and remove the hard drive from the hard-drive bracket.

Installing The Hard Drive

1. Replace the hard drive into the hard-drive bracket.

2. Install the hard drive into its slot in the computer..

3. Connect the SATA cable and the power cable to the hard drive.

4. Install the:

• bezel

• cover

5. Follow the procedures in After Working Inside Your Computer.

Removing the Expansion Card(s)

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the cover.

3. Follow the steps to remove the expansion card:

a. Press the blue tab and slide down the release lever that secures the expansion card.

b. Press on the retaining tab to release the expansion card from its connector.

c. Lift the expansion card up out of its connector and remove it from the computer.

d. Repeat the same sequence of steps to remove any additional expansion card installed.

Installing the Expansion Card(s)

1. Place the expansion card in its connector.

2. Secure the expansion card by pushing the card-retention latch until it snaps into place.

3. Repeat the steps to install any additional expansion cards.

4. Install the cover.

5. Follow the procedures in After Working Inside Your Computer.

Removing The Power Supply Unit (PSU)

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the:

• cover

• bezel

• optical drive

• hard drive

3. Disconnect the following power supply cables from the system board by pressing on the retention

latch and lifting it upwards.

• system fan power cable [1.2]

• system board power cable [3,4]

a. Un-thread the power cables from the metal clips.

4. Follow the steps below to remove the power supply unit:

a. Remove the screws that secure the power supply to the computer.

b. Push-in on the blue release tab beside the power supply [1].

c. Slide the power supply unit towards the front and remove it from the computer [2].

Installing The Power Supply Unit (PSU)

1. Place the power supply unit into the computer.

2. Slide the power supply unit towards the back of the computer till it snaps into place.

3. Replace the screws to secure the power supply unit to the computer.

4. Thread the power cables through the metal clips.

5. Connect the power cables to the system board.

6. Install the:

• optical drive

• hard drive

• bezel

• cover

7. Follow the procedures in After Working Inside Your Computer.

Removing The Heatsink

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the:

• cover

• bezel

• optical drive

• hard drive

3. Follow the steps below to remove the processor heat sink:

a. Disconnect the heat sink and fan assembly cable from the system board.

b. Loosen the captive-screws that secure the heat sink and fan assembly to the system board.

c. Lift the heat sink and fan assembly upward and remove it from the computer.

Installing The Heatsink

1. Place the heat sink and fan assembly on the processor.

2. Tighten the captive-screws that secure the heat sink and fan assembly to the system board.

3. Connect the heat sink and fan assembly cable to the system board.

4. Install the:

• bezel

• cover

5. Follow the procedures in After Working Inside Your Computer.

Removing the Processor

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the:

• cover

• heatsink

3. Push the processor release lever down and then press it outward to release it from the retention

hook that secures it.

4. Raise the processor cover and lift the processor to remove it from the computer.

Installing the Processor

1. Install the processor into the socket.

2. Press down the processor cover to secure it inside the socket.

3. Push the release lever down and then press it inward to hold the retention hook that secures it.

4. Install the:

• heatsink

• cover

5. Follow the procedures in After Working Inside Your Computer.

Removing the Memory

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the cover.

3. Press down on the memory-retaining tabs on each side of the memory modules and lift the memory

module upwards to remove it from the computer.

Installing the Memory

1. Align the notch on the memory-card with the tab in the system-board connector.

2. Insert the memory module into the memory socket.

3. Press down on the memory module until the securing clips secure the memory in place.

4. Install the cover.

5. Follow the procedures in After Working Inside Your Computer.

Removing The System Fan

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the:

• cover

• bezel

• hard drive

3. Follow the steps below to remove the system fan cables:

a. Disconnect the fan cable from the system board. [1]

b. Un-thread the system fan cable from the metal retention clips. [2,3]

4. Follow the steps below to remove the system fan:

a. Remove the screws that secure the system fan to the computer.

b. Remove the system fan from the computer.

Installing The System Fan

1. Place the fan on the computer.

2. Replace the screws to secure the fan to the computer.

3. Thread the system fan cable through the metal retention clips.

4. Connect the fan cable to the system board.

5. Install the:

• hard drive

• bezel

• cover

6. Follow the procedures in After Working Inside Your Computer.

Removing The Input/Output (I/O) Panel

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the:

• cover

• bezel

• hard drive

• optical drive

3. Follow the steps below to disconnect the I/O panel cables:

a. Disconnect the I/O panel and FlyWire cables from the system board.

b. Un-thread the cables from the metal retention clips.

4. Follow the steps below to remove the I/O panel:

a. Remove the screw that secures the I/O panel to the computer.

b. Slide the I/O panel outwards and remove it from the computer.

Installing The Input/Output (I/O) Panel

1. Slide the I/O panel into its slot on the computer.

2. Replace the screw that secures the I/O panel.

3. Route the three cables through the metal clips.

4. Connect the three I/O panel and FlyWire cables to the system board.

5. Install the:

• optical drive

• hard drive

• bezel

• cover

6. Follow the procedures in After Working Inside Your Computer.

Removing The System Board

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the:

• cover

• bezel

• optical drive

• hard drive

• heatsink

• processor

• memory

• expansion cards

• I/O panel

3. Follow the steps below to remove the system board:

a. Disconnect and un-thread all the cables connected to the system board.

b. Remove the screws that secure the system board to the computer.

c. Slide the system board towards the front of the computer and tilt to a 45–degree angle.

d. Lift the system board out of the computer.

Installing The System Board

1. Place the system board into the computer at a 45–degrees angle and then slide it towards the back

of the computer.

2. Replace the screws to secure the system board to the computer.

3. Thread and connect all the cables connected to the system board.

4. Install the:

• I/O panel

• memory

• expansion cards

• processor

• heatsink

• hard drive

• optical drive

• bezel

• cover

5. Follow the procedures in After Working Inside Your Computer.

System Board Components

The following image displays the system board components .

1. PCI connector 2. PCIe x1 connector

3. PCIe x16 connector 4. PCIe x1 connector

5. P2 power connector 6. processor socket

7. CPU fan connector 8. memory connectors

9. P1 power connector 10. card reader module connector

11. real-time clock reset jumper 12. password reset jumper

13. front USB connector 14. SATA connectors

15. front LED connector 16. system fan connector

17. SATA connectors 18. coin-cell battery

19. front audio connector

Troubleshooting Your Computer

You can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error

Messages during the operation of the computer.

Diagnostic Power LED Codes

Power LED Light Status Possible Cause Troubleshooting Steps

Off The computer is either turned off

or is not receiving power.

• Re-seat the power cable in

the power connector on the

back of the computer and the

electrical outlet.

• If the computer is plugged

into a power strip, ensure the

power strip is plugged into an

electrical outlet and is turned

on. Also, bypass power

protection devices, power

strips, and power extension

cables to verify the computer

turns on properly.

• Ensure the electrical outlet is

working by testing it with

another device, such as a

lamp.

Blinking Amber Computer fails to complete

POST or processor failure.

• Remove and then reinstall any

cards.

• Remove and then reinstall the

graphics card, if applicable.

• Ensure the power cable is

connected to the

motherboard and processor.

Steady Amber Computer is in standby or this is

a computer fault error condition,

including the power supply. Only

the +5VSB rail on the power

supply is working correctly.

• Press the power button to

bring the computer out of

standby mode.

• Ensure all power cables are

securely connected to the

system board.

• Ensure the main power cable

and front panel cable are

securely connected to the

system board.

Steady White The computer is fully functional

and in the On state.

If the computer is not

responding, do the following:

• Ensure the display is

connected and turned on.

Power LED Light Status Possible Cause Troubleshooting Steps

• If the display is connected

and turned on, listen for a

beep code.

Diagnostic Error Messages

Error Messages Description

AUXILIARY DEVICE FAILURE The touchpad or external mouse may be faulty. For

an external mouse, check the cable connection.

Enable the Pointing Device option in the system

setup program.

BAD COMMAND OR FILE NAME Ensure that you have spelled the command

correctly, put spaces in the proper place, and used

the correct pathname.

CACHE DISABLED DUE TO FAILURE The primary cache internal to the microprocessor

has failed. Contact Dell.

CD DRIVE CONTROLLER FAILURE The optical drive does not respond to commands

from the computer.

DATA ERROR The hard drive cannot read the data.

DECREASING AVAILABLE MEMORY One or more memory modules may be faulty or

improperly seated. Reinstall the memory modules

or, if necessary, replace them.

DISK C: FAILED INITIALIZATION The hard drive failed initialization. Run the hard

drive tests in the Dell Diagnostics.

DRIVE NOT READY The operation requires a hard drive in the bay

before it can continue. Install a hard drive in the

hard drive bay.

ERROR READING PCMCIA CARD The computer cannot identify the ExpressCard.

Reinsert the card or try another card.

EXTENDED MEMORY SIZE HAS CHANGED The amount of memory recorded in non-volatile

memory (NVRAM) does not match the memory

installed in the computer. Restart the computer. If

the error appears again, contact Dell.

THE FILE BEING COPIED IS TOO LARGE FOR THE

DESTINATION DRIVE

The file that you are trying to copy is too large to fit

on the disk, or the disk is full. Try copying the file to

a different disk or use a larger capacity disk.

A FILENAME CANNOT CONTAIN ANY OF THE

FOLLOWING CHARACTERS: \ / : * ? " < > | -

Do not use these characters in filenames.

GATE A20 FAILURE A memory module may be loose. Reinstall the

memory modules or, if necessary, replace them.

Error Messages Description

GENERAL FAILURE The operating system is unable to carry out the

command. The message is usually followed by

specific information. For example, Printer out of

paper. Take the appropriate action.

HARD-DISK DRIVE CONFIGURATION ERROR The computer cannot identify the drive type. Shut

down the computer, remove the hard drive, and

boot the computer from an optical drive. Then,

shut down the computer, reinstall the hard drive,

and restart the computer. Run the Hard Disk Drive

tests in the Dell Diagnostics.

HARD-DISK DRIVE CONTROLLER FAILURE 0 The hard drive does not respond to commands

from the computer. Shut down the computer,

remove the hard drive, and boot the computer

from an optical drive. Then, shut down the

computer, reinstall the hard drive, and restart the

computer. If the problem persists, try another

drive. Run the Hard Disk Drive tests in the Dell

Diagnostics.

HARD-DISK DRIVE FAILURE The hard drive does not respond to commands

from the computer. Shut down the computer,

remove the hard drive, and boot the computer

from an optical drive. Then, shut down the

computer, reinstall the hard drive, and restart the

computer. If the problem persists, try another

drive. Run the Hard Disk Drive tests in the Dell

Diagnostics.

HARD-DISK DRIVE READ FAILURE The hard drive may be defective. Shut down the

computer, remove the hard drive, and boot the

computer from an optical. Then, shut down the

computer, reinstall the hard drive, and restart the

computer. If the problem persists, try another

drive. Run the Hard Disk Drive tests in the Dell

Diagnostics.

INSERT BOOTABLE MEDIA The operating system is trying to boot to non-

bootable media, such as a floppy disk or optical

drive. Insert bootable media.

INVALID CONFIGURATION INFORMATION-PLEASE

RUN SYSTEM SETUP PROGRAM

The system configuration information does not

match the hardware configuration. The message is

most likely to occur after a memory module is

installed. Correct the appropriate options in the

system setup program.

KEYBOARD CLOCK LINE FAILURE For external keyboards, check the cable

connection. Run the Keyboard Controller test in

the Dell Diagnostics.

Error Messages Description

KEYBOARD CONTROLLER FAILURE For external keyboards, check the cable

connection. Restart the computer, and avoid

touching the keyboard or the mouse during the

boot routine. Run the Keyboard Controller test in

the Dell Diagnostics.

KEYBOARD DATA LINE FAILURE For external keyboards, check the cable

connection. Run theKeyboard Controller test in

the Dell Diagnostics.

KEYBOARD STUCK KEY FAILURE For external keyboards or keypads, check the cable

connection. Restart the computer, and avoid

touching the keyboard or keys during the boot

routine. Run the Stuck Key test in the Dell

Diagnostics.

LICENSED CONTENT IS NOT ACCESSIBLE IN

MEDIADIRECT

Dell MediaDirect cannot verify the Digital Rights

Management (DRM) restrictions on the file, so the

file cannot be played.

MEMORY ADDRESS LINE FAILURE AT ADDRESS,

READ VALUE EXPECTING VALUE

A memory module may be faulty or improperly

seated. Reinstall the memory modules or, if

necessary, replace them.

MEMORY ALLOCATION ERROR The software you are attempting to run is

conflicting with the operating system, another

program, or a utility. Shut down the computer, wait

30 seconds, and then restart it. Try to run the

program again. If the error message still appears,

see the software documentation.

MEMORY DOUBLE WORD LOGIC FAILURE AT

ADDRESS, READ VALUE EXPECTING VALUE

A memory module may be faulty or improperly

seated. Reinstall the memory modules or, if

necessary, replace them.

MEMORY ODD/EVEN LOGIC FAILURE AT

ADDRESS, READ VALUE EXPECTING VALUE

A memory module may be faulty or improperly

seated. Reinstall the memory modules or, if

necessary, replace them.

MEMORY WRITE/READ FAILURE AT ADDRESS,

READ VALUE EXPECTING VALUE

A memory module may be faulty or improperly

seated. Reinstall the memory modules or, if

necessary, replace them.

NO BOOT DEVICE AVAILABLE The computer cannot find the hard drive. If the

hard drive is your boot device, ensure that the drive

is installed, properly seated, and partitioned as a

boot device.

NO BOOT SECTOR ON HARD DRIVE The operating system may be corrupted, contact

Dell.

NO TIMER TICK INTERRUPT A chip on the system board may be

malfunctioning. Run the System Set tests in

theDell Diagnostics.

Error Messages Description

NOT ENOUGH MEMORY OR RESOURCES. EXIT

SOME PROGRAMS AND TRY AGAIN

You have too many programs open. Close all

windows and open the program that you want to

use.

OPERATING SYSTEM NOT FOUND Reinstall the hard drive. If the problem persists,

contact Dell.

OPTIONAL ROM BAD CHECKSUM The optional ROM has failed. Contact Dell.

SECTOR NOT FOUND The operating system cannot locate a sector on

the hard drive. You may have a defective sector or

corrupted FAT on the hard drive. Run the Windows

error-checking utility to check the file structure on

the hard drive. See Windows Help and Support for

instructions (click Start > Help and Support). If a

large number of sectors are defective, back up the

data (if possible), and then reformat the hard drive.

SEEK ERROR The operating system cannot find a specific track

on the hard drive.

SHUTDOWN FAILURE A chip on the system board may be

malfunctioning. Run the System Set tests in the

contact Dell .

TIME-OF-DAY CLOCK LOST POWER System configuration settings are corrupted.

Connect your computer to an electrical outlet to

charge the battery. If the problem persists, try to

restore the data by entering the system setup

program, then immediately exit the program. If the

message reappears, contact Dell.

TIME-OF-DAY CLOCK STOPPED The reserve battery that supports the system

configuration settings may require recharging.

Connect your computer to an electrical outlet to

charge the battery. If the problem persists, contact

Dell.

TIME-OF-DAY NOT SET-PLEASE RUN THE SYSTEM

SETUP PROGRAM

The time or date stored in the system setup

program does not match the system clock. Correct

the settings for the Date and Time options.

TIMER CHIP COUNTER 2 FAILED A chip on the system board may be

malfunctioning. Run the System Set tests in the

Dell Diagnostics.

UNEXPECTED INTERRUPT IN PROTECTED MODE The keyboard controller may be malfunctioning, or

a memory module may be loose. Run the System

Memory tests and the Keyboard Controller test in

the System Setup or contact Dell.

X:\ IS NOT ACCESSIBLE. THE DEVICE IS NOT

READY

Insert a disk into the drive and try again.

System Error Messages

System Message Description

Alert! Previous attempts at booting this system

have failed at checkpoint [nnnn]. For help in

resolving this problem, please note this checkpoint

and contact Dell Technical Support

The computer failed to complete the boot routine

three consecutive times for the same error.

CMOS checksum error Possible motherboard failure or Real-time clock

(RTC) battery low.

CPU fan failure CPU fan has failed

System fan failure System fan has failed

Hard-disk drive failure Possible hard disk drive failure during POST

Keyboard failure Keyboard failure or loose cable. If reseating the

cable does not solve the problem, replace the

keyboard.

No boot device available No bootable partition on hard disk drive, the hard

disk drive cable is loose, or no bootable device

exists.

• If the hard drive is your boot device, ensure that

the cables are connected and that the drive is

installed properly and partitioned as a boot

device.

• Enter system setup and ensure that the boot

sequence information is correct.

No timer tick interrupt A chip on the system board might be

malfunctioning or motherboard failure.

USB over current error Disconnect the USB device. The USB device needs

more power for it to function properly. Use an

external power source to connect the USB device,

or if the device has two USB cables, connect both

of them.

CAUTION - Hard Drive SELF MONITORING

SYSTEM has reported that a parameter has

exceeded its normal operating range. Dell

recommends that you back up your data regularly.

A parameter out of range may or may not indicate

a potential hard drive problem

S.M.A.R.T error, possible hard disk drive failure

System Setup

System Setup Overview

System Setup allows you to:

• change the system configuration information after you add, change, or remove any hardware in your

computer.

• set or change a user-selectable option such as the user password.

• read the current amount of memory or set the type of hard drive installed.

Before you use System Setup, it is recommended that you write down the System Setup screen

information for future reference.

CAUTION: Unless you are an expert computer user, do not change the settings for this program.

Certain changes can cause your computer to work incorrectly.

Enter System Setup

1. Turn on (or restart) your computer.

2. After the white Dell logo appears, press <F2> or <F12> immediately.

The System Setup page displays.

NOTE: If you wait too long and the operating system logo appears, continue to wait until you

see the desktop. Then, shut down or restart your computer and try again.

System Setup Options

Main

System Information Displays the computer model number.

BIOS Version Displays the BIOS revision.

Build Date Displays the date the system BIOS was built.

System Date Re-sets the date on the computer's internal

calendar.

System Time Re-sets the time on the computer's internal clock.

Service Tag Displays the service tag of your computer.

Asset Tag Displays the asset tag of your computer (if

available).

Processor Information

Processor Type Displays the type of processor.

Processor ID Displays the processor ID

Processor Core Count Displays the processor core count

L1 Cache Size Displays the processor L1 cache size.

L2 Cache Size Displays the processor L2 cache size.

L3 Cache Size Displays the processor L3 cache size.

Memory Information

Memory Installed Displays the total computer memory.

Memory Available Displays the available memory.

Memory Speed Displays the memory speed.

Memory Technology Displays the type and technology.

SATA Information

SATA 0 Displays the model number and capacity of the

hard drive.

SATA 1 Displays the model number and capacity of the

hard drive.

SATA 2 Displays the model number and capacity of the

hard drive.

SATA 3 Displays the model number and capacity of the

hard drive.

Advanced

Processor Configuration

Multi Core Support Enable or disable Multi Core

Support.

Default: Enabled

Limit CPUID Value Enable or disable the Limit CPUID

Value feature.

Default: Enabled

CPU XD Support Enable or disable the CPU XD

feature.

Default: Enabled

Intel Virtualization Technology Enable or disable the Intel

Virtualization feature.

Default: Enabled

Intel SpeedStep Enable or disable the Intel

SpeedStep feature.

Default: Enabled

Intel Turbo Boost Technology Enable or disable Intel Turbo

Boost Technology.

Default: Enabled

USB Configuration

Front USB Ports Enable or disable the Front USB

Ports.

Default: Enabled

Rear USB Ports Enable or disable the Rear USB

Ports.

Default: Enabled

Processor Configuration

Onboard Device Configuration

Onboard Audio Controller Enable or disable the onboard

audio controller.

Default: Enabled

SATA Mode Displays the SATA Mode Default: AHCI

Intel Multi-Display Enable or disable the Intel Multi-

Display Technology.

Default: Disabled

Onboard LAN Controller Enable or disable the onboard

LAN controller.

Default: Enabled

Onboard LAN Boot ROM Enable or disable the onboard

LAN boot ROM.

Default: Disabled

Boot

Numlock Key Enables of disables the numlock

key during Boot.

Secure Boot Control Enable or disable the Secure

Boot Control.

Load Legacy OPROM Enable or disable loading of a

legacy OPROM

Keyboard Errors Enable or disable displaying

keyboard errors.

USB Boot Support Enable or Disable USB Boot

Support.

Boot Mode Select the Boot mode.

1st Boot Device Enable or disable the boot

device.

2nd Boot Device Enable or disable the boot

device.

3rd Boot Device Enable or disable the boot

device.

4th Boot Device Enable or disable the boot

device.

5th Boot Device Enable or disable the boot

device.

Hard Disk Drivers Display information about Hard

Disk Drivers

Network Drivers Displays information about

Network Drives

Power

Wake up by Integrated LAN/WLAN Enable or disable Wake up by Integrated LAN/

WLAN

AC Recovery Specifies the AC recovery mode.

Auto Power On Enable or disable Auto Power On mode.

Security

Supervisor Password Specifies whether an administrator password has

been assigned.

User Password Specifies whether a user password has been

assigned.

Set Supervisor Password Allows you to change or delete the administrator

password.

HDD Protection Enable or disable HDD protection.

Exit

This section allows you to save, discard, and load default settings before exiting from System Setup.

Specifications

NOTE: Offerings may vary by region. The following specifications are only those required by law to

ship with your computer. For more information about the configuration of your computer, go to

Help and Support in your Windows operating system and select the option to view information

about your computer.

Processor

Type • Intel Celeron

• Intel Pentium Dual Core

• Intel Dual Core i3 (4th Generation)

• Intel Dual Core i5 (4th Generation)

• Intel Dual Core i7 (4th Generation)

L3 cache Up to 8 MB

Memory

Memory module connector two DIMM slots

Memory module capacity 2 GB, 4 GB, 6 GB, 8 GB, and 16 GB

Type 1600 MHz DDR3 (Non-ECC)

Minimum memory 2 GB

Maximum memory 16 GB

Video

Video Type:

Integrated Intel HD 4600 Graphics

Discrete PCI Express x16 graphics card

• Nvidia GT 705

• Nvidia GTX 745

Integrated video memory Shared system memory

Audio

Integrated Integrated 5.1 high-definition audio

Network

Integrated Realtek 10/100/1000 Mbps Ethernet

System Information

Chipset Intel H81

BIOS chip (NVRAM) 8M SPI Flash ROM

Expansion Bus

Bus speed:

PCI Express PCIe 2.0 at speeds upto 5.0 GT/s

SATA 0,1 SATA Gen 3 at 6 GB/s and 2,3 SATA Gen 2 at 3

GB/s

USB 80 Mbps

Cards Vostro 3800 Vostro 3900 series

PCIe x16 one half-height card one full height card

PCIe x1 up to two half-height cards up to two full height cards

PCI one half height card one full height card

Drives

Externally accessible:

5.25 inch drive bays one

Internally accessible:

3.5 inch drive bays one

External Connectors

Audio:

Back panel three connectors

Front Panel two front-panel connectors for headphone and

microphone

Network one RJ45 connector

USB:

Front panel • two USB 2.0 connectors

Back panel four USB 2.0 connectors, two USB 3.0 connectors

PS 2 used to connect a PS 2 compatible keyboard or

mouse

Video • one 15-hole VGA connector

• one 19-pin HDMI connector

Control Lights And Diagnostic Lights

power button light white light — solid white light indicates power-on

state.

amber light — solid amber light indicates sleep/stand

by state of the computer; blinking amber light

indicates a problem with the system board.

drive activity light white light — blinking white light indicates that the

computer is reading data from, or writing data to the

hard drive.

Power Vostro 3800 Vostro 3900 series

Coin-cell battery 3 V CR2032 lithium coin

cell

3 V CR2032 lithium coin

cell

Input voltage 90 VAC – 132 VAC / 180

VAC–264 VAC

180 VAC–264 VAC

Input frequency 50 Hz to 60 Hz 50 Hz to 60 Hz

Wattage 250 W 300 W

Input current 8.00 A / 4.00 A 4.50 A

NOTE: Vostro V 3800 :Total power output of +5 V and +3.30 V can not exceed 75 W

NOTE: Vostro V 3900 :Total power output of +5 V and +3.30 V can not exceed 90 W

Maximum heat dissipation 853 BTU/hr 1024 BTU/hr

NOTE: Heat dissipation is calculated by using the power supply wattage rating.

Physical

Vostro 3800:

Height 380 mm (14.96 inches)

Width 102 mm (4.01 inches)

Depth 433.1 mm (17.05 inches)

Weight (Minimum) 7.2 kg (15.87 lb)

Vostro 3900 series:

Height 380 mm (14.96 inches)

Width 175 mm (6.88 inches)

Depth 436.3 mm (17.17 inches)

Weight (Minimum) 8.5 kg (18.73 lb)

Environmental

Temperature:

Operating 10 °C to 35 °C (50 °F to 95 °F)

Storage –40 °C to 65 °C (–40 °F to 149 °F)

Relative humidity 20 % to 80 % (non-condensing)

Altitude:

NOTE: V 3800 and V 3900 meet the China

5000 m altitude requirements.

Operating –15.20 m to 3048 m (–50 ft to 10,000 ft)

Storage –15.20 m to 10,668 m (–50 ft to 35,000 ft)

Airborne contaminant level G1 as defined by ISA-S71.04–1985

Contacting Dell

NOTE: If you do not have an active Internet connection, you can find contact information on your

purchase invoice, packing slip, bill, or Dell product catalog.

Dell provides several online and telephone-based support and service options. Availability varies by

country and product, and some services may not be available in your area. To contact Dell for sales,

technical support, or customer service issues:

1. Visit dell.com/support

2. Select your support category.

3. Verify your country or region in the Choose a Country/Region drop-down menu at the top of page.

4. Select the appropriate service or support link based on your need.

Table of Contents

DELL 3800 User Manual

Related Manuals