DELL 5401 User Manual

Displayed below is the user manual for 5401 by DELL which is a product in the Notebooks category. This manual has pages.

Related Manuals

DELL 5401 Manual

Vostro 5401

Service Manual

Regulatory Model: P130G

Regulatory Type: P130G001

August 2020

Rev. A02

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

trademarks may be trademarks of their respective owners.

Chapter 1: Working on your computer............................................................................................7

Safety instructions.............................................................................................................................................................. 7

Before working inside your computer....................................................................................................................... 7

Safety precautions........................................................................................................................................................ 8

Electrostatic discharge—ESD protection................................................................................................................8

ESD field service kit ..................................................................................................................................................... 9

After working inside your computer........................................................................................................................ 10

Chapter 2: Major components of your system...............................................................................11

Chapter 3: Disassembly and reassembly.......................................................................................13

Recommended tools..........................................................................................................................................................13

Screw list..............................................................................................................................................................................13

Base cover........................................................................................................................................................................... 15

Removing the base cover...........................................................................................................................................15

Installing the base cover.............................................................................................................................................16

Battery.................................................................................................................................................................................. 18

Lithium-ion battery precautions............................................................................................................................... 18

Removing the 3-cell battery - UMA/discrete....................................................................................................... 19

Installing the 3-cell battery - UMA/discrete.........................................................................................................20

Removing the 4-cell battery - UMA/discrete....................................................................................................... 21

Installing the 4-cell battery - UMA/discrete......................................................................................................... 21

WLAN card..........................................................................................................................................................................22

Removing the WLAN card - UMA........................................................................................................................... 22

Installing the WLAN card - UMA..............................................................................................................................23

Removing the WLAN card - discrete......................................................................................................................24

Installing the WLAN card - discrete........................................................................................................................25

Memory modules............................................................................................................................................................... 26

Removing the memory modules - UMA................................................................................................................. 26

Installing the memory modules - UMA....................................................................................................................27

Removing the memory modules - discrete............................................................................................................28

Installing the memory modules - discrete..............................................................................................................29

Solid-state drive................................................................................................................................................................. 31

Removing the M.2 2280 solid-state drive - UMA................................................................................................ 31

Installing the M.2 2280 solid-state drive - UMA.................................................................................................. 31

Removing the M.2 2230 solid-state drive - UMA................................................................................................32

Installing the M.2 2230 solid-state drive - UMA..................................................................................................33

Removing the M.2 2280 solid-state drive - SSD-1 - discrete.......................................................................... 34

Installing the M.2 2280 solid-state drive - SSD-1 - discrete.............................................................................34

Removing the M.2 2230 solid-state drive - SSD-1 - discrete.......................................................................... 35

Installing the M.2 2230 solid-state drive - SSD-1 - discrete.............................................................................36

Replacing the SSD-1 support bracket.....................................................................................................................37

Removing the M.2 2280 solid-state drive - SSD-2 - discrete..........................................................................38

Installing the M.2 2280 solid-state drive - SSD-2 - discrete............................................................................39

Contents

Contents 3

Speakers.............................................................................................................................................................................. 40

Removing the speakers (in 3-cell battery configuration)..................................................................................40

Installing the speakers (in 3-cell battery configuration).....................................................................................41

Removing the speakers (in 4-cell battery configuration).................................................................................. 42

Installing the speakers (in 4-cell battery configuration).................................................................................... 43

System fan..........................................................................................................................................................................45

Removing the system fan - UMA............................................................................................................................ 45

Installing the system fan - UMA.............................................................................................................................. 46

Removing the system fan - discrete.......................................................................................................................47

Installing the system fan - discrete.........................................................................................................................48

Heat sink..............................................................................................................................................................................49

Removing the heat sink - UMA................................................................................................................................49

Installing the heat sink - UMA..................................................................................................................................50

Removing the heat sink - discrete.......................................................................................................................... 50

Installing the heat sink - discrete............................................................................................................................. 51

Coin-cell battery................................................................................................................................................................ 52

Removing the coin-cell battery - UMA.................................................................................................................. 52

Installing the coin-cell battery - UMA.................................................................................................................... 53

Removing the coin-cell battery - discrete.............................................................................................................54

Installing the coin-cell battery - discrete...............................................................................................................54

I/O board.............................................................................................................................................................................55

Removing the I/O board - UMA.............................................................................................................................. 55

Installing the I/O board - UMA................................................................................................................................ 56

Removing the I/O board - discrete.........................................................................................................................58

Installing the I/O board - discrete...........................................................................................................................59

Power button with fingerprint reader (optional).......................................................................................................60

Removing the power button and optional fingerprint reader - UMA..............................................................60

Installing the power button with finger reader - UMA........................................................................................61

Removing the power button and optional fingerprint reader - discrete........................................................62

Installing the power button with finger reader - discrete ................................................................................ 62

DC-in port........................................................................................................................................................................... 63

Removing the DC-in port - UMA.............................................................................................................................63

Installing the DC-in port - UMA............................................................................................................................... 64

Removing the DC-in port - discrete....................................................................................................................... 65

Installing the DC-in port - discrete......................................................................................................................... 66

Touchpad.............................................................................................................................................................................67

Removing the touchpad - UMA............................................................................................................................... 67

Installing the touchpad - UMA................................................................................................................................. 69

Removing the touchpad - discrete..........................................................................................................................70

Installing the touchpad - discrete.............................................................................................................................71

Display assembly................................................................................................................................................................ 72

Removing the display assembly - UMA.................................................................................................................. 72

Installing the display assembly - UMA.................................................................................................................... 74

Removing the display assembly - discrete............................................................................................................ 75

Installing the display assembly - discrete...............................................................................................................78

System board..................................................................................................................................................................... 80

Removing the system board - UMA....................................................................................................................... 80

Installing the system board - UMA..........................................................................................................................82

Removing the system board - discrete..................................................................................................................85

Installing the system board - discrete.................................................................................................................... 87

4Contents

Palm-rest and keyboard assembly................................................................................................................................ 90

Removing the palm-rest and keyboard assembly - UMA.................................................................................. 90

Installing the palm-rest and keyboard assembly - UMA..................................................................................... 91

Removing the palm-rest and keyboard assembly - discrete.............................................................................92

Installing the palm-rest and keyboard assembly - discrete............................................................................... 93

Chapter 4: Software....................................................................................................................95

Downloading Windows drivers....................................................................................................................................... 95

Chapter 5: System setup.............................................................................................................96

Boot menu...........................................................................................................................................................................96

Navigation keys..................................................................................................................................................................96

Boot Sequence...................................................................................................................................................................97

BIOS setup.......................................................................................................................................................................... 97

Overview........................................................................................................................................................................97

Boot configuration...................................................................................................................................................... 98

Integrated Devices...................................................................................................................................................... 99

Storage.........................................................................................................................................................................100

Display.......................................................................................................................................................................... 100

Connection options.................................................................................................................................................... 101

Power management................................................................................................................................................... 101

Security........................................................................................................................................................................ 102

Password..................................................................................................................................................................... 103

Update and Recovery............................................................................................................................................... 105

System management................................................................................................................................................ 105

Keyboard...................................................................................................................................................................... 106

Pre-boot behavior......................................................................................................................................................107

Virtualization support................................................................................................................................................108

Performance............................................................................................................................................................... 108

System logs................................................................................................................................................................. 109

Updating the BIOS in Windows ...................................................................................................................................109

Updating BIOS on systems with BitLocker enabled...........................................................................................110

Updating the Dell BIOS in Linux and Ubuntu environments.............................................................................110

Flashing the BIOS from the F12 One-Time boot menu..................................................................................... 110

System and setup password.......................................................................................................................................... 113

Assigning a system setup password.......................................................................................................................113

Deleting or changing an existing system setup password................................................................................ 114

Chapter 6: Troubleshooting........................................................................................................ 115

Built-in self-test (BIST).................................................................................................................................................. 115

System board built-in self-test (M-BIST).................................................................................................................. 116

Display panel power rail built-in self-test (L-BIST)............................................................................................ 116

Display panel power rail built-in self-test (L-BIST).................................................................................................. 117

Display panel built-in self-test (LCD-BIST)................................................................................................................117

Outcome............................................................................................................................................................................. 118

SupportAssist diagnostics.............................................................................................................................................. 118

Running the SupportAssist diagnostics...................................................................................................................... 118

System diagnostic lights................................................................................................................................................. 118

Recovering the operating system................................................................................................................................120

Contents 5

Flashing the BIOS............................................................................................................................................................ 120

Flashing BIOS (USB key)............................................................................................................................................... 120

Backup media and recovery options........................................................................................................................... 120

WiFi power cycle...............................................................................................................................................................121

Releasing Ethernet (RJ-45) cable................................................................................................................................121

Chapter 7: Getting help..............................................................................................................122

Contacting Dell................................................................................................................................................................. 122

6 Contents

Working on your computer

Topics:

•Safety instructions

Safety instructions

Prerequisites

Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless

otherwise noted, each procedure included in this document assumes that the following conditions exist:

●You have read the safety information that shipped with your computer.

●A component can be replaced or, if purchased separately, installed by performing the removal procedure in reverse order.

About this task

NOTE: Disconnect all power sources before opening the computer cover or panels. After you finish working inside the

computer, replace all covers, panels, and screws before connecting to the power source.

WARNING: Before working inside your computer, read the safety information that shipped with your computer.

For additional safety best practices information, see the Regulatory Compliance Homepage

CAUTION: Many repairs may only be done by a certified service technician. You should only perform

troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or

telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by

your warranty. Read and follow the safety instructions that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically

touching an unpainted metal surface at the same time as touching a connector on the back of the computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a

card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by

its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some

cables have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking

tabs before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending

any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and

aligned.

NOTE: The color of your computer and certain components may appear differently than shown in this document.

Before working inside your computer

About this task

To avoid damaging your computer, perform the following steps before you begin working inside the computer.

Steps

1. Ensure that you follow the Safety Instruction.

2. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

Working on your computer 7

3. Turn off your computer.

4. Disconnect all network cables from the computer.

CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the

cable from the network device.

5. Disconnect your computer and all attached devices from their electrical outlets.

6. Press and hold the power button while the computer is unplugged to ground the system board.

NOTE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an

unpainted metal surface at the same time as touching a connector on the back of the computer.

Safety precautions

The safety precautions chapter details the primary steps to be taken before performing any disassembly instructions.

Observe the following safety precautions before you perform any installation or break/fix procedures involving disassembly or

reassembly:

●Turn off the system and all attached peripherals.

●Disconnect the system and all attached peripherals from AC power.

●Disconnect all network cables, telephone, and telecommunications lines from the system.

●Use an ESD field service kit when working inside any notebook to avoid electrostatic discharge (ESD) damage.

●After removing any system component, carefully place the removed component on an anti-static mat.

●Wear shoes with non-conductive rubber soles to reduce the chance of getting electrocuted.

Standby power

Dell products with standby power must be unplugged before you open the case. Systems that incorporate standby power are

essentially powered while turned off. The internal power enables the system to be remotely turned on (wake on LAN) and

suspended into a sleep mode and has other advanced power management features.

Unplugging, pressing and holding the power button for 15 seconds should discharge residual power in the system board. Remove

the battery from notebooks.

Bonding

Bonding is a method for connecting two or more grounding conductors to the same electrical potential. This is done through the

use of a field service electrostatic discharge (ESD) kit. When connecting a bonding wire, ensure that it is connected to bare

metal and never to a painted or non-metal surface. The wrist strap should be secure and in full contact with your skin, and

ensure that you remove all jewelry such as watches, bracelets, or rings prior to bonding yourself and the equipment.

Electrostatic discharge—ESD protection

ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards,

processors, memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such

as intermittent problems or a shortened product life span. As the industry pushes for lower power requirements and increased

density, ESD protection is an increasing concern.

Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than

in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.

Two recognized types of ESD damage are catastrophic and intermittent failures.

●Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes an

immediate and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has received

a static shock and immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or

nonfunctional memory.

●Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of

intermittent failures means that most of the time when damage occurs, it is not immediately recognizable. The DIMM

receives a static shock, but the tracing is merely weakened and does not immediately produce outward symptoms related to

8Working on your computer

the damage. The weakened trace may take weeks or months to melt, and in the meantime may cause degradation of memory

integrity, intermittent memory errors, etc.

The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded")

failure.

Perform the following steps to prevent ESD damage:

●Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do

not provide adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on

parts with increased sensitivity to ESD damage.

●Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.

●When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static

packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you

discharge static electricity from your body.

●Before transporting a static-sensitive component, place it in an anti-static container or packaging.

ESD field service kit

The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components:

anti-static mat, wrist strap, and bonding wire.

Components of an ESD field service kit

The components of an ESD field service kit are:

●Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an

anti-static mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal

on the system being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly

on the mat. ESD-sensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.

●Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist

and bare metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that

is temporarily placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD

mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never use

wireless wrist straps. Always be aware that the internal wires of a wrist strap are prone to damage from normal wear and

tear, and must be checked regularly with a wrist strap tester in order to avoid accidental ESD hardware damage. It is

recommended to test the wrist strap and bonding wire at least once per week.

●ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored

kit, it is a best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A wrist

strap tester is the best method for doing this test. If you do not have your own wrist strap tester, check with your regional

office to find out if they have one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is

strapped to your wrist and push the button to test. A green LED is lit if the test is successful; a red LED is lit and an alarm

sounds if the test fails.

●Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts

that are insulators and often highly charged.

●Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For

example, deploying the kit for a server environment is different than for a desktop or portable environment. Servers are

typically installed in a rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always

look for a large open flat work area that is free of clutter and large enough to deploy the ESD kit with additional space to

accommodate the type of system that is being repaired. The workspace should also be free of insulators that can cause an

ESD event. On the work area, insulators such as Styrofoam and other plastics should always be moved at least 12 inches or

30 centimeters away from sensitive parts before physically handling any hardware components

●ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded

bags are preferred. However, you should always return the damaged part using the same ESD bag and packaging that the

new part arrived in. The ESD bag should be folded over and taped shut and all the same foam packing material should be

used in the original box that the new part arrived in. ESD-sensitive devices should be removed from packaging only at an

ESD-protected work surface, and parts should never be placed on top of the ESD bag because only the inside of the bag is

shielded. Always place parts in your hand, on the ESD mat, in the system, or inside an anti-static bag.

●Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts

to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.

Working on your computer 9

ESD protection summary

It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static

mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all

insulator parts while performing service and that they use anti-static bags for transporting sensitive components.

After working inside your computer

About this task

After you complete any replacement procedure, ensure that you connect any external devices, cards, and cables before turning

on your computer.

Steps

1. Connect any telephone or network cables to your computer.

CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the

computer.

2. Connect your computer and all attached devices to their electrical outlets.

3. Turn on your computer.

4. If required, verify that the computer works correctly by running SupportAssist diagnostics.

10 Working on your computer

Major components of your system

1. Base cover

2. Battery

3. DC-in port

4. Heat sink

5. Memory module

6. Solid-state drive shield

7. M.2 2230 SSD

8. Speaker

9. System board

10. Touchpad

11. Palm-rest and keyboard assembly

12. Display assembly

13. Power button with fingerprint reader

14. Coin-cell battery

15. I/O board

16. System fan

17. WLAN card

Major components of your system 11

18. M.2 2280 SSD

NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These

parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative for

purchase options.

12 Major components of your system

Disassembly and reassembly

Topics:

•Recommended tools

•Screw list

•Base cover

•Battery

•WLAN card

•Memory modules

•Solid-state drive

•Speakers

•System fan

•Heat sink

•Coin-cell battery

•I/O board

•Power button with fingerprint reader (optional)

•DC-in port

•Touchpad

•Display assembly

•System board

•Palm-rest and keyboard assembly

Recommended tools

The procedures in this document may require the following tools:

●Phillips #0 screwdriver

●Phillips #1 screwdriver

●Plastic scribe (recommended for field technicians)

NOTE: The #0 screw driver is for screws 0-1, and the #1 screw driver is for screws 2-4.

Screw list

NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and

then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type is

restored when the component is replaced.

NOTE: Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surface when

replacing a component.

NOTE: Screw color may vary with the configuration ordered.

Table 1. Screw list

Component Screw type Quantity Screw image

Base cover M2x8.8 - captive

M2x4

Disassembly and reassembly 13

Table 1. Screw list (continued)

Component Screw type Quantity Screw image

Battery M2x3 4

WLAN M2x3 1

Solid-state drive -1 M2x3 1

Solid-state drive - 2 M2x3 2

Solid-state drive -2 support

bracket

M1.6x2 1

System fan M2x2 2

Heat sink - UMA M2x5.35 - captive 4

Heat sink - discrete M2x5.35 - captive 7

Hinge screws M2.5x4

M2x3

I/O board M2x3 3

Power button with fingerprint

reader

M2x2.5 2

DC-in port M2x3 1

Touchpad 1.6x2

M2x2

Display assembly M2.5x4

M2x3

System board M2x3 2

14 Disassembly and reassembly

Base cover

Removing the base cover

Prerequisites

Follow the procedure in before working inside your computer.

About this task

The figure indicates the location of the base cover and provides a visual representation of the removal procedure.

Disassembly and reassembly 15

Steps

1. Remove the five screws (M2x4) that secure the base cover to the palm-rest and keyboard assembly.

2. Loosen the two captive screws (M2x8.8) that secure the base cover to the palm-rest and keyboard assembly.

3. Pry open the base cover starting from the recess at the hinge area and work your way around and follow the "guidance line"

indicated in the image to remove the base cover.

4. Lift the base cover off the palm-rest and keyboard assembly.

Installing the base cover

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the base cover and provides a visual representation of the installation procedure.

16 Disassembly and reassembly

Disassembly and reassembly 17

Steps

1. Place the base cover on the palm-rest and keyboard assembly, and snap the base cover into place.

2. Tighten the two captive screws (M2x8.8) that secure the base cover to the palm-rest and keyboard assembly.

3. Replace the five screws (M2x4) that secure the base cover to the palm-rest and keyboard assembly.

Next steps

Follow the procedure in after working inside your computer.

Battery

Lithium-ion battery precautions

CAUTION:

●Exercise caution when handling Lithium-ion batteries.

●Discharge the battery completely before removing it. Disconnect the AC power adapter from the system and

operate the computer solely on battery power—the battery is fully discharged when the computer no longer

turns on when the power button is pressed.

●Do not crush, drop, mutilate, or penetrate the battery with foreign objects.

●Do not expose the battery to high temperatures, or disassemble battery packs and cells.

18 Disassembly and reassembly

●Do not apply pressure to the surface of the battery.

●Do not bend the battery.

●Do not use tools of any kind to pry on or against the battery.

●Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental

puncture or damage to the battery and other system components.

●If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing,

bending, or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical

support for assistance. See www.dell.com/contactdell.

●Always purchase genuine batteries from www.dell.com or authorized Dell partners and resellers.

Removing the 3-cell battery - UMA/discrete

Prerequisites

NOTE:

The battery type in your computer varies depending on the configuration ordered.

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

About this task

The figure indicates the location of the 3-cell battery in an UMA configuration and provides a visual representation of the

removal procedure.

Steps

1. Disconnect the battery cable from the system board.

2. Remove the four screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.

Disassembly and reassembly 19

3. Lift the battery off the palm-rest and keyboard assembly.

Installing the 3-cell battery - UMA/discrete

Prerequisites

NOTE:

The battery type in your computer varies depending on the configuration ordered.

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the 3-cell battery in an UMA configuration and provides a visual representation of the

installation procedure.

Steps

1. Place the battery on the palm-rest and keyboard assembly and align the screw holes on the battery with the screw holes on

the palm-rest and keyboard assembly.

2. Install the four screws (M2x3) that secure the battery to the system board and palm-rest and keyboard assembly.

3. Connect the battery cable to the system board.

Next steps

1. Install the base cover.

2. Follow the procedure in after working inside your computer.

20 Disassembly and reassembly

Removing the 4-cell battery - UMA/discrete

Prerequisites

NOTE:

The battery type in your computer varies depending on the configuration ordered.

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

About this task

The figure indicates the location of the battery in a discrete configuration and provides a visual representation of the removal

procedure.

Steps

1. Disconnect the battery cable from the system board.

2. Remove the four screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.

3. Lift the battery off the palm-rest and keyboard assembly.

Installing the 4-cell battery - UMA/discrete

Prerequisites

NOTE:

The battery type in your computer varies depending on the configuration ordered.

If you are replacing a component, remove the existing component before performing the installation procedure.

Disassembly and reassembly 21

About this task

The figure indicates the location of the battery in a discrete configuration and provides a visual representation of the installation

procedure.

Steps

1. Place the battery on the palm-rest and keyboard assembly and align the screw holes on the battery with the screw holes on

the palm-rest and keyboard assembly.

2. Install the four screws (M2x3) that secure the battery to the system board and palm-rest and keyboard assembly.

3. Connect the battery cable to the system board.

Next steps

1. Install the base cover.

2. Follow the procedure in after working inside your computer.

WLAN card

Removing the WLAN card - UMA

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

About this task

The figure indicates the location of the WLAN card and provides a visual representation of the removal procedure.

22 Disassembly and reassembly

Steps

1. Remove the single screw (M2x3) that secures the WLAN card bracket to the WLAN card.

2. Remove the WLAN card bracket from the WLAN card.

3. Disconnect the antenna cables from the WLAN card.

4. Slide and remove the WLAN card from the WLAN card slot.

Installing the WLAN card - UMA

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the WLAN card and provides a visual representation of the installation procedure.

Disassembly and reassembly 23

Steps

1. Align the notch on the WLAN card with the tab on the WLAN card slot and insert the WLAN card at an angle into the WLAN

card slot.

2. Connect the antenna cables to the WLAN card.

3. Align and place the WLAN card bracket on the WLAN card.

4. Replace the screw (M2x3) to secure the WLAN card bracket to the WLAN card.

Next steps

1. Install the battery.

2. Install the base cover.

3. Follow the procedure in after working inside your computer.

Removing the WLAN card - discrete

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

About this task

The figure indicates the location of the WLAN card and provides a visual representation of the removal procedure.

24 Disassembly and reassembly

Steps

1. Remove the single screw (M2x3) that secures the WLAN card bracket to the WLAN card.

2. Remove the WLAN card bracket from the WLAN card.

3. Disconnect the antenna cables from the WLAN card.

4. Slide and remove the WLAN card from the WLAN card slot.

Installing the WLAN card - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the WLAN card and provides a visual representation of the installation procedure.

Disassembly and reassembly 25

Steps

1. Align the notch on the WLAN card with the tab on the WLAN card slot and insert the WLAN card at an angle into the WLAN

card slot.

2. Connect the antenna cables to the WLAN card.

3. Align and place the WLAN card bracket on the WLAN card.

4. Replace the screw (M2x3) to secure the WLAN card bracket to the WLAN card.

Next steps

1. Install the battery.

2. Install the base cover.

3. Follow the procedure in after working inside your computer.

Memory modules

Removing the memory modules - UMA

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Disconnect the battery.

26 Disassembly and reassembly

About this task

The figure indicates the location of the memory module and provides a visual representation of the removal procedure.

Steps

1. Lift the mylar covering the memory module.

2. Using your finger tips gently pry the retention clips away from the memory module until the memory module pops up.

3. Slide and remove the memory module off the memory module slot on the system board.

Installing the memory modules - UMA

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the memory module and provides a visual representation of the installation procedure.

Disassembly and reassembly 27

Steps

1. Lift the mylar, and align the notch on the memory module with the tab on the memory-module slot.

2. Slide the memory module firmly into the slot at an angle.

3. Press the memory module down until it clicks into place.

NOTE: If you do not hear the click, remove the memory module and reinstall it.

Next steps

1. Connect the battery.

2. Install the base cover.

3. Follow the procedure in after working inside your computer.

Removing the memory modules - discrete

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Disconnect the battery.

28 Disassembly and reassembly

About this task

The figure indicates the location of the memory module and provides a visual representation of the removal procedure.

Steps

1. Lift the mylar covering the memory module.

2. Using your finger tips gently pry the retention clips away from the memory module until the memory module pops up.

3. Slide and remove the memory module off the memory module slot on the system board.

Installing the memory modules - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the memory module and provides a visual representation of the installation procedure.

Disassembly and reassembly 29

Steps

1. Lift the mylar, and align the notch on the memory module with the tab on the memory-module slot.

2. Slide the memory module firmly into the slot at an angle.

3. Press the memory module down until it clicks into place.

NOTE: If you do not hear the click, remove the memory module and reinstall it.

Next steps

1. Connect the battery.

2. Install the base cover.

3. Follow the procedure in after working inside your computer.

30 Disassembly and reassembly

Solid-state drive

Removing the M.2 2280 solid-state drive - UMA

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Disconnect the battery.

About this task

The figure indicates the location of the M.2 2280 solid-state drive and provides a visual representation of the removal

procedure.

Steps

1. Remove the single screw (M2x3) that secures the solid-state drive to the palm-rest and keyboard assembly.

2. Slide and remove the solid-state drive module from the solid-state drive slot on the system board.

Installing the M.2 2280 solid-state drive - UMA

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the solid-state drive bracket and provides a visual representation of the bracket alignment

procedure to accommodate the M.2 2280 solid-state drive.

Disassembly and reassembly 31

Steps

1. Align the solid-state drive bracket to accommodate the M.2 2280 solid-state drive.

2. Replace the single (M2x3) screw to secure the solid-state drive module to the palm-rest and keyboard assembly.

Next steps

1. Connect the battery.

2. Install the base cover.

3. Follow the procedure in after working inside your computer.

Removing the M.2 2230 solid-state drive - UMA

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Disconnect the battery.

About this task

The figure indicates the location of the M.2 2230 solid-state drive and provides a visual representation of the removal

procedure.

32 Disassembly and reassembly

Steps

1. Remove the single screw (M2x3) that secures the solid-state drive to the palm-rest and keyboard assembly.

2. Slide and remove the solid-state drive module from the solid-state drive slot on the system board.

Installing the M.2 2230 solid-state drive - UMA

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the solid-state drive bracket and provides a visual representation of the bracket alignment

procedure to accommodate the M.2 2230 solid-state drive.

Disassembly and reassembly 33

Steps

1. Align the solid-state drive bracket to accommodate the M.2 2230 solid-state drive.

2. Replace the single (M2x3) screw to secure the solid-state drive module to the palm-rest and keyboard assembly.

Next steps

1. Connect the battery.

2. Install the base cover.

3. Follow the procedure in after working inside your computer.

Removing the M.2 2280 solid-state drive - SSD-1 - discrete

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Disconnect the battery.

About this task

NOTE: Slot one supports both M.2 2230 and M.2 2280 SSD.

The figure indicates the location of the M.2 2280 solid-state drive in slot one and provides a visual representation of the removal

procedure.

Steps

1. Remove the single screw (M2x3) that secures the solid-state drive to the palm-rest and keyboard assembly.

2. Slide and remove the solid-state drive module from the solid-state drive slot on the system board.

Installing the M.2 2280 solid-state drive - SSD-1 - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

34 Disassembly and reassembly

About this task

NOTE: Slot one supports both M.2 2230 and M.2 2280 SSD.

The figure indicates the location of the solid-state drive in slot 1 and provides a visual representation of the alignment procedure

to accommodate the M.2 2280 solid-state drive.

Steps

1. Align the solid-state drive bracket to accommodate the M.2 2280 solid-state drive.

2. Replace the single (M2x3) screw to secure the solid-state drive module to the palm-rest and keyboard assembly.

Next steps

1. Connect the battery.

2. Install the base cover.

3. Follow the procedure in after working inside your computer.

Removing the M.2 2230 solid-state drive - SSD-1 - discrete

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Disconnect the battery.

About this task

NOTE: Slot one supports both M.2 2230 and M.2 2280 SSD.

The figure indicates the location of the M.2 2230 solid-state drive in slot one and provides a visual representation of the removal

procedure.

Disassembly and reassembly 35

Steps

1. Remove the single screw (M2x3) that secures the solid-state drive to the palm-rest and keyboard assembly.

2. Slide and remove the solid-state drive module from the solid-state drive slot on the system board.

Installing the M.2 2230 solid-state drive - SSD-1 - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

NOTE: Slot one supports both M.2 2230 and M.2 2280 SSD.

The figure indicates the location of the solid-state drive in slot one and provides a visual representation of the bracket alignment

procedure to accommodate the M.2 2230 solid-state drive.

36 Disassembly and reassembly

Steps

1. Align the solid-state drive bracket to accommodate the M.2 2230 solid-state drive.

2. Replace the single (M2x3) screw to secure the solid-state drive module to the palm-rest and keyboard assembly.

Next steps

1. Connect the battery.

2. Install the base cover.

3. Follow the procedure in after working inside your computer.

Replacing the SSD-1 support bracket

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery - UMA or discrete.

4. Remove the UMA (M.2 2230 SSD or M.2 2280 SSD) or discrete (M.2 2230 SSD or M.2 2280 SSD).

About this task

The figure provides a visual representation of the replace procedure.

Disassembly and reassembly 37

Steps

1. Slide and remove the SSD support bracket from the support bracket slot.

2. Depending on the type of solid-state drive (M.2 2230/ M.2 2280), align and insert the SSD support bracket into the support

bracket slot.

3. Install the solid-state drive.

Removing the M.2 2280 solid-state drive - SSD-2 - discrete

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Disconnect the battery.

About this task

NOTE: If you have ordered a 3-cell battery configuration, your computer will not have a solid-state drive installed in M.2

slot two.

NOTE: If you have ordered a 4-cell battery configuration, your computer may have a 2230 solid-state drive or a 2280 solid-

state drive installed in M.2 slot two. The computer comes with a SSD bracket and the user will have to purchase the SSD.

NOTE: This procedure applies only to computers shipped with a 2280 solid-state drive installed in M.2 slot two.

The figure indicates the location of the solid-state drive and provides a visual representation of the removal procedure of M.2

2280 SSD from slot two.

38 Disassembly and reassembly

Steps

1. Remove the single screw (M1.6x2) that secures the solid-state drive module support bracket to the palm-rest and keyboard

assembly.

2. Lift and remove the solid-state drive support bracket from the solid-state drive slot.

3. Remove the single screw (M2x3) that secures the solid-state drive module to the palm-rest and keyboard assembly.

4. Slide and remove the solid-state drive module from the solid-state drive slot.

Installing the M.2 2280 solid-state drive - SSD-2 - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

NOTE: Slot two supports both M.2 2230 and M.2 2280 SSD.

About this task

NOTE: If you have ordered a 3-cell battery configuration, your computer will not have a solid-state drive installed in M.2

slot two.

NOTE: If you have ordered a 4-cell battery configuration, your computer may have a 2230 solid-state drive or a 2280 solid-

state drive installed in M.2 slot two. The computer comes with a SSD bracket and the user will have to purchase the SSD.

NOTE: This procedure applies only to computers shipped with a 2280 solid-state drive installed in M.2 slot two.

The figure indicates the location of the solid-state drive support bracket and provides a visual representation of the bracket

alignment procedure to accommodate the M.2 2280 solid-state drive from slot 2.

Disassembly and reassembly 39

Steps

1. Align the solid-state drive bracket to accommodate the M.2 2280 solid-state drive.

2. Replace the single screw (M2x3) that secures the solid-state drive module to the palm-rest and keyboard assembly.

3. Place the solid-state drive module bracket.

4. Replace the single (M1.6x2) screw to secure the solid-state drive bracket to the palm-rest and keyboard assembly.

Next steps

1. Connect the battery.

2. Install the base cover.

3. Follow the procedure in after working inside your computer.

Speakers

Removing the speakers (in 3-cell battery configuration)

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

About this task

The figure indicates the location of the speakers in a system configuration with 3-cell battery and provides a visual

representation of the removal procedure.

40 Disassembly and reassembly

Steps

1. Locate the speakers on your computer.

2. Disconnect the speaker cable from the connector on the system board.

3. Peel the adhesive tape that secures the speaker cable.

4. Unroute the speaker cables from the retention clips on the computer.

5. Lift the speakers, along with the cable, off the palm-rest and keyboard assembly.

Installing the speakers (in 3-cell battery configuration)

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the speakers in a system configuration with 3-cell battery and provides a visual

representation of the installation procedure.

Disassembly and reassembly 41

Steps

1. Using the alignment posts and rubber grommets, place the speakers in the slots on the palm-rest and keyboard assembly.

2. Route the speaker cable through the routing guides on the palm-rest and keyboard assembly.

3. Connect the speaker cable to the system board.

Next steps

1. Install the battery.

2. Install the base cover.

3. Follow the procedure in after working inside your computer.

Removing the speakers (in 4-cell battery configuration)

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

42 Disassembly and reassembly

About this task

The figure indicates the location of the speakers in a system configuration with 4-cell battery and provides a visual

representation of the removal procedure.

Steps

1. Locate the speakers on your computer.

2. Disconnect the speaker cable from the connector on the system board.

3. Peel the adhesive tape that secures the speaker cable.

4. Unroute the speaker cables from the retention clips on the computer.

5. Lift the speakers, along with the cable, off the palm-rest and keyboard assembly.

Installing the speakers (in 4-cell battery configuration)

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

Disassembly and reassembly 43

About this task

The figure indicates the location of the speakers in a system configuration with 4-cell battery and provides a visual

representation of the installation procedure.

Steps

1. Using the alignment posts and rubber grommets, place the speakers in the slots on the palm-rest and keyboard assembly.

2. Route the speaker cable through the routing guides on the palm-rest and keyboard assembly.

3. Connect the speaker cable to the system board.

Next steps

1. Install the battery.

2. Install the base cover.

3. Follow the procedure in after working inside your computer.

44 Disassembly and reassembly

System fan

Removing the system fan - UMA

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

About this task

The figure indicates the location of the system fan and provides a visual representation of the removal procedure.

Steps

1. Lift the mylar cover.

2. Disconnect the system fan cable from the system board.

3. Peel the adhesive tape, and unroute the I/O cable.

4. Remove the two (M2x2) screws that secure the system fan to the palm-rest and keyboard assembly.

Disassembly and reassembly 45

5. Slide and lift the system fan off the palm-rest and keyboard assembly.

Installing the system fan - UMA

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the system fan and provides a visual representation of the installation procedure.

Steps

1. Slide and place the system fan on the palm-rest and keyboard assembly.

2. Align the screw holes on the system fan with the screw holes on the palm-rest and keyboard assembly.

3. Replace the two (M2x2) screws to secure the system fan to the palm-rest and keyboard assembly.

4. Connect the system fan cable to the system board.

5. Route the I/O cable underneath the system fan and connect it to the system board.

6. Place the mylar cover back.

46 Disassembly and reassembly

Next steps

1. Install the battery.

2. Install the base cover.

3. Follow the procedure in after working inside your computer.

Removing the system fan - discrete

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

About this task

The figure indicates the location of the system fan and provides a visual representation of the removal procedure.

Steps

1. Lift the mylar cover.

2. Disconnect the system fan cable from the system board.

Disassembly and reassembly 47

3. Peel the adhesive tape, and unroute the I/O cable.

4. Remove the two (M2x2) screws that secure the system fan to the palm-rest and keyboard assembly.

5. Slide and lift the system fan off the palm-rest and keyboard assembly.

Installing the system fan - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the system fan and provides a visual representation of the installation procedure.

Steps

1. Slide and place the system fan on the palm-rest and keyboard assembly.

2. Align the screw holes on the system fan with the screw holes on the palm-rest and keyboard assembly.

3. Replace the two (M2x2) screws to secure the system fan to the palm-rest and keyboard assembly.

4. Connect the system fan cable to the system board.

5. Route the I/O cable underneath the system fan and connect it to the system board.

48 Disassembly and reassembly

6. Place the mylar cover back.

Next steps

1. Install the battery.

2. Install the base cover.

3. Follow the procedure in after working inside your computer.

Heat sink

Removing the heat sink - UMA

NOTE: The heat sink type in your computer varies depending on the configuration ordered.

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

4. Remove the system fan.

About this task

The figure indicates the location of the heat sink and provides a visual representation of the removal procedure.

Steps

1. In sequential order (as indicated on the heat sink), loosen the four captive screws that secure the heat sink to the system

board.

2. Lift and remove the heat sink off the system board.

Disassembly and reassembly 49

Installing the heat sink - UMA

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the heat sink and provides a visual representation of the installation procedure.

Steps

1. Place the heat sink on the system board and align the screw holes on the heat sink with the screw holes on the system

board.

2. In sequential order (as indicated on the heat sink), tighten the four captive screws that secure the heat sink to the system

board.

Next steps

1. Install the system fan.

2. Install the battery.

3. Install the base cover.

4. Follow the procedure in after working inside your computer.

Removing the heat sink - discrete

NOTE: The heat sink type in your computer varies depending on the configuration ordered.

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

4. Remove the system fan.

50 Disassembly and reassembly

About this task

The figure indicates the location of the heat sink and provides a visual representation of the removal procedure.

Steps

1. In sequential order (as indicated on the heat sink), loosen the seven captive screws that secure the heat sink to the system

board.

2. Lift and remove the heat sink off the system board.

Installing the heat sink - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the heat sink and provides a visual representation of the installation procedure.

Disassembly and reassembly 51

Steps

1. Place the heat sink on the system board and align the screw holes on the heat sink with the screw holes on the system

board.

2. In sequential order (as indicated on the heat sink), tighten the seven captive screws that secure the heat sink to the system

board.

Next steps

1. Install the system fan.

2. Install the battery.

3. Install the base cover.

4. Follow the procedure in after working inside your computer.

Coin-cell battery

Removing the coin-cell battery - UMA

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

NOTE: Removing the coin-cell battery resets the BIOS setup program settings to default. It is recommended that you note

the BIOS setup program settings before removing the coin-cell battery.

About this task

The figure indicates the location of the coin-cell battery and provides a visual representation of the removal procedure.

52 Disassembly and reassembly

Steps

1. Disconnect the coin-cell battery cable from the I/O board.

2. Peel the coin-cell battery off the palm-rest and keyboard assembly.

Installing the coin-cell battery - UMA

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the coin-cell battery and provides a visual representation of the installation procedure.

Disassembly and reassembly 53

Steps

1. Adhere the coin-cell battery to the slot on the palm-rest and keyboard assembly.

2. Route the coin-cell battery cable as illustrated and connect it to the I/O board.

Next steps

1. Install the battery.

2. Install the base cover.

3. Follow the procedure in after working inside your computer.

Removing the coin-cell battery - discrete

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

NOTE: Removing the coin-cell battery resets the BIOS setup program settings to default. It is recommended that you note

the BIOS setup program settings before removing the coin-cell battery.

About this task

The figure indicates the location of the coin-cell battery and provides a visual representation of the removal procedure.

Steps

1. Disconnect the coin-cell battery cable from the I/O board.

2. Peel the coin-cell battery off the palm-rest and keyboard assembly.

Installing the coin-cell battery - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

54 Disassembly and reassembly

About this task

The figure indicates the location of the coin-cell battery and provides a visual representation of the installation procedure.

Steps

1. Adhere the coin-cell battery to the slot on the palm-rest and keyboard assembly.

2. Route the coin-cell battery cable as illustrated and connect it to the I/O board.

Next steps

1. Install the battery.

2. Install the base cover.

3. Follow the procedure in after working inside your computer.

I/O board

Removing the I/O board - UMA

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

4. Remove the system fan.

5. Remove the coin-cell battery.

About this task

The figure indicates the location of the I/O board and provides a visual representation of the removal procedure.

Disassembly and reassembly 55

Steps

1. Locate the I/O board on your computer.

2. Lift the mylar cover.

3. Peel the adhesive tape to unroute the I/O cable.

4. Open the latch, and disconnect the I/O-board cable from the I/O board.

5. Remove the two screws (M2.5x4) and (M2x3) that secure the left display hinge to the computer.

6. Open the latch, and disconnect the fingerprint reader cable from the I/O board.

7. Remove the three screws (M2x3) that secure the I/O board to the palm-rest and keyboard assembly.

8. Lift the I/O board off the palm-rest and keyboard assembly.

Installing the I/O board - UMA

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the I/O board and provides a visual representation of the installation procedure.

56 Disassembly and reassembly

Steps

1. Place the I/O board on the palm-rest and keyboard assembly.

2. Align the screw holes on the I/O board with the screw holes on the palm-rest and keyboard assembly.

3. Replace the three screws (M2x3) that secure the I/O board to the palm-rest and keyboard assembly.

4. Connect the fingerprint reader cable to the I/O board and close the latch to secure the cable.

5. Lower the left hinge, and replace the two screws (M2.5x4) and (M2x3).

6. Route the I/O cable underneath the system fan using adhesive tape.

7. Connect the I/O-board cable to the I/O board and close the latch to secure the cable.

8. Place the mylar cover back.

Next steps

1. Install the coin-cell battery.

2. Install the system fan.

3. Install the battery.

4. Install the base cover.

5. Follow the procedure in after working inside your computer.

Disassembly and reassembly 57

Removing the I/O board - discrete

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

4. Remove the system fan.

5. Remove the coin-cell battery.

About this task

The figure indicates the location of the I/O board and provides a visual representation of the removal procedure.

Steps

1. Locate the I/O board on your computer.

2. Lift the mylar cover.

3. Peel the adhesive tape to unroute the I/O cable.

4. Open the latch, and disconnect the I/O-board cable from the I/O board.

5. Remove the two screws (M2.5x4) and (M2x3) that secure the left hinge to the computer.

6. Lift the left hinge.

7. Open the latch, and disconnect the fingerprint reader cable from the I/O board.

58 Disassembly and reassembly

8. Remove the three screws (M2x3) that secure the I/O board to the palm-rest and keyboard assembly.

9. Lift the I/O board off the palm-rest and keyboard assembly.

Installing the I/O board - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the I/O board and provides a visual representation of the installation procedure.

Steps

1. Place the I/O board on the palm-rest and keyboard assembly.

2. Align the screw holes on the I/O board with the screw holes on the palm-rest and keyboard assembly.

3. Replace the three screws (M2x3) that secure the I/O board to the palm-rest and keyboard assembly.

4. Connect the fingerprint reader cable to the I/O board and close the latch to secure the cable.

5. Lower the left hinge, and replace the two screws (M2.5x4) and (M2x3).

6. Route the I/O cable underneath the system fan using adhesive tape.

7. Connect the I/O-board cable to the I/O board and close the latch to secure the cable.

Disassembly and reassembly 59

8. Place the mylar cover back.

Next steps

1. Install the coin-cell battery.

2. Install the system fan.

3. Install the battery.

4. Install the base cover.

5. Follow the procedure in after working inside your computer.

Power button with fingerprint reader (optional)

Removing the power button and optional fingerprint reader - UMA

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery .

4. Remove the system fan.

5. Remove theM.2 2280 SSD or M.2 2230 SSD.

6. Remove the I/O board.

7. Remove the coin-cell battery.

About this task

The figure indicates the location of the power button with optional fingerprint reader and provides a visual representation of the

removal procedure.

Steps

1. Unplug the fingerprint reader cable from the connector on the palm-rest and keyboard assembly.

2. Lift the latch, and unplug the I/O cable from the connector on the palm-rest and keyboard assembly.

3. Remove the I/O cable from the palm-rest and keyboard assembly.

60 Disassembly and reassembly

4. Remove the two screws (M2x2.5) that secure the power button with optional fingerprint reader to the palm-rest and

keyboard assembly.

5. Lift the power button with optional fingerprint reader, along with the fingerprint reader cable, off the palm-rest and

keyboard assembly.

Installing the power button with finger reader - UMA

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the power button with fingerprint reader and provides a visual representation of the

installation procedure.

Steps

1. Using the alignment post, place the power button with fingerprint reader on the palm-rest and keyboard assembly.

2. Replace the two screws (M2x2.5) to secure the power button with optional fingerprint reader to the palm-rest and keyboard

assembly.

3. Plug the I/O cable into the connector on palm-rest and keyboard assembly and close the latch.

4. Plug the fingerprint reader cable into the connector on palm-rest and keyboard assembly.

Next steps

1. Install the I/O board.

2. Install the system fan.

3. Install the coin-cell battery.

4. Install the M.2 2280 SSD or M.2 2230 SSD.

5. Install the battery.

6. Install the base cover.

7. Follow the procedure in after working inside your computer.

Disassembly and reassembly 61

Removing the power button and optional fingerprint reader -

discrete

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

4. Remove the system fan.

5. Remove the M.2 2280 SSD or M.2 2230 SSD.

6. Remove the I/O board.

7. Remove the coin-cell battery.

About this task

The figure indicates the location of the power button with optional fingerprint reader and provides a visual representation of the

removal procedure.

Steps

1. Unplug the fingerprint reader cable from the connector on the palm-rest and keyboard assembly.

2. Lift the latch, and unplug the I/O cable from the connector on the palm-rest and keyboard assembly.

3. Remove the I/O cable from the palm-rest and keyboard assembly.

4. Remove the two screws (M2x2.5) that secure the power button with optional fingerprint reader to the palm-rest and

keyboard assembly.

5. Lift the power button with optional fingerprint reader, along with the fingerprint reader cable, off the palm-rest and

keyboard assembly.

Installing the power button with finger reader - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

62 Disassembly and reassembly

About this task

The figure indicates the location of the power button with fingerprint reader and provides a visual representation of the

installation procedure.

Steps

1. Using the alignment post, place the power button with fingerprint reader on the palm-rest and keyboard assembly.

2. Replace the two screws (M2x2.5) to secure the power button with optional fingerprint reader to the palm-rest and keyboard

assembly.

3. Plug the I/O cable into the connector on palm-rest and keyboard assembly and close the latch.

4. Plug the fingerprint reader cable into the connector on palm-rest and keyboard assembly.

Next steps

1. Install the I/O board.

2. Install the system fan.

3. Install the coin-cell battery.

4. Install the M.2 2280 SSD or M.2 2230 SSD.

5. Install the battery.

6. Install the base cover.

7. Follow the procedure in after working inside your computer.

DC-in port

Removing the DC-in port - UMA

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

Disassembly and reassembly 63

About this task

The figure indicates the location of the DC-in and provides a visual representation of the removal procedure.

Steps

1. Locate the DC-in port on your computer.

2. Remove the two (M2.5x4) screws, and lift the metal hinge.

3. Remove the single screw (M2x3) screw and lift the DC-in port.

4. Peel the transparent sticker covering the DC-in port.

5. Disconnect the DC-in cable from the system board.

6. Lift the DC-in port off the palm-rest and keyboard assembly.

Installing the DC-in port - UMA

About this task

The figure indicates the location of the DC-in and provides a visual representation of the removal procedure.

64 Disassembly and reassembly

Steps

1. Place the DC-in port on the palm-rest and keyboard assembly.

2. Replace the single screw (M2x3) on the DC-in port using bracket.

3. Connect the DC-in cable to the system board.

4. Adhere the transparent sticker.

5. Lower the metal hinge.

6. Replace the two (M2.5x4) screws, and tighten it.

Next steps

1. Install the battery.

2. Install the base cover.

3. Follow the procedure in after working inside your computer.

Removing the DC-in port - discrete

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

Disassembly and reassembly 65

About this task

The figure indicates the location of the DC-in and provides a visual representation of the removal procedure.

Steps

1. Locate the DC-in port on your computer.

2. Remove the two (M2.5x4) screws, and lift the metal hinge.

3. Remove the single screw (M2x3) screw and lift the DC-in port.

4. Peel the transparent sticker.

5. Disconnect the DC-in cable from the system board.

6. Lift the DC-in port off the palm-rest and keyboard assembly.

Installing the DC-in port - discrete

About this task

The figure indicates the location of the DC-in and provides a visual representation of the removal procedure.

66 Disassembly and reassembly

Steps

1. Place the DC-in port on the palm-rest and keyboard assembly.

2. Replace the single screw (M2x3) on the DC-in port using bracket.

3. Connect the DC-in cable to the system board.

4. Adhere the transparent sticker.

5. Lower the metal hinge.

6. Replace the two (M2.5x4) screws, and tighten it.

Next steps

1. Install the battery.

2. Install the base cover.

3. Follow the procedure in after working inside your computer.

Touchpad

Removing the touchpad - UMA

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

Disassembly and reassembly 67

3. Remove the battery.

4. Remove the speakers.

About this task

The figure indicates the location of the touchpad and provides a visual representation of the removal procedure.

Steps

1. Peel adhesive tape, and unroute the speaker cable.

2. Remove the three (M1.6x2) screws that secure the touchpad bracket to the palm-rest and keyboard assembly.

3. Lift the touchpad bracket off the palm-rest and keyboard assembly.

4. Open the latch, and disconnect the touchpad cable from the system board.

5. Remove the adhesive tape from the touchpad bracket.

6. Remove the two (M2x2) screws that secure the touchpad bracket to the palm-rest and keyboard assembly.

7. Lift the touchpad, along with the cable, off the palm-rest and keyboard assembly.

68 Disassembly and reassembly

Installing the touchpad - UMA

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the component and provides a visual representation of the installation procedure.

Steps

1. Align and place the touchpad into the slot on the palm-rest and keyboard assembly.

2. Replace the two (M2x2) screws along with the bracket to secure the touchpad to the palm-rest and keyboard assembly.

3. Slide the touchpad cable onto its connector on the system board and close the latch to secure the cable.

4. Align and place the touchpad bracket into the slot on the palm-rest and keyboard assembly.

5. Replace the three (M1.6x2) screws that secure the touchpad bracket to the palm-rest and keyboard assembly.

6. Lower the latch of the touchpad cable once it is connected to the connector on the system board.

Next steps

1. Install the speakers.

Disassembly and reassembly 69

2. Install the battery.

3. Install the base cover.

4. Follow the procedure in after working inside your computer.

Removing the touchpad - discrete

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

4. Remove the speakers.

About this task

The figure indicates the location of the touchpad and provides a visual representation of the removal procedure.

Steps

1. Peel adhesive tape, and unroute the speaker cable.

2. Remove the three (M1.6x2) screws that secure the touchpad bracket to the palm-rest and keyboard assembly.

70 Disassembly and reassembly

3. Lift the touchpad bracket off the palm-rest and keyboard assembly.

4. Open the latch, and disconnect the touchpad cable from the system board.

5. Remove the adhesive tape from the touchpad bracket.

6. Remove the two (M2x2) screws that secure the touchpad bracket to the palm-rest and keyboard assembly.

7. Lift the touchpad, along with the cable, off the palm-rest and keyboard assembly.

Installing the touchpad - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the component and provides a visual representation of the installation procedure.

Steps

1. Align and place the touchpad into the slot on the palm-rest and keyboard assembly.

2. Replace the two (M2x2) screws along with the bracket to secure the touchpad to the palm-rest and keyboard assembly.

3. Slide the touchpad cable onto its connector on the system board and close the latch to secure the cable.

Disassembly and reassembly 71

4. Align and place the touchpad bracket into the slot on the palm-rest and keyboard assembly.

5. Replace the three (M1.6x2) screws that secure the touchpad bracket to the palm-rest and keyboard assembly.

6. Lower the latch on the touchpad cable once it is connected to the connector on the system board.

Next steps

1. Install the speakers.

2. Install the battery.

3. Install the base cover.

4. Follow the procedure in after working inside your computer.

Display assembly

Removing the display assembly - UMA

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

4. Remove the WLAN card.

About this task

The figure indicates the location of the display assembly and provides a visual representation of the removal procedure.

72 Disassembly and reassembly

Steps

1. Locate the display cable and display hinges on your computer.

2. Remove the transparent sticker covering the display cable to the system board.

3. Peel the tape that secures the display cable to the system board.

4. Open the latch, and disconnect the display cable from the system board.

Disassembly and reassembly 73

5. Remove the two screws (M2.5x4) and (M2x3) that secure the left-display hinge to the system board.

6. Remove the two screws (M2.5x4) that secure the right-display hinge to the system board.

7. Open the display hinges at an angle of 90 degrees.

8. Gently slide the palm-rest and keyboard assembly off the display assembly carefully.

Installing the display assembly - UMA

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the component and provides a visual representation of the installation procedure.

74 Disassembly and reassembly

Steps

1. Place the display assembly on a clean and flat surface.

2. Align and place the palm-rest and keyboard assembly on the display assembly.

3. Using the alignment posts, close the display hinges.

4. Replace the two screws (M2.5x4) and (M2x3) that secure the left-display hinge to the system board.

5. Replace the two screws (M2.5x4) that secure the right-display hinge to the system board.

6. Connect the display cable on to the connector on the system board and adhere the tape to the system board.

Next steps

1. Install the WLAN card.

2. Install the battery.

3. Install the base cover.

4. Follow the procedure in after working inside your computer.

Removing the display assembly - discrete

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

4. Remove the WLAN card.

About this task

The figure indicates the location of the display assembly and provides a visual representation of the removal procedure.

Disassembly and reassembly 75

76 Disassembly and reassembly

Disassembly and reassembly 77

Steps

1. Locate the display cable and display hinges on your computer.

2. Remove the transparent sticker covering the display cable to the system board.

3. Peel the tape that secures the display cable to the system board.

4. Open the latch, and disconnect the display cable from the system board.

5. Remove the two screws (M2.5x4) and (M2x3) that secure the left-display hinge to the system board.

6. Remove the two screws (M2.5x4) that secure the right-display hinge to the system board.

7. Open the display hinges at an angle of 90 degrees.

8. Gently slide the palm-rest and keyboard assembly off the display assembly carefully.

Installing the display assembly - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the component and provides a visual representation of the installation procedure.

78 Disassembly and reassembly

Disassembly and reassembly 79

Steps

1. Place the display assembly on a clean and flat surface.

2. Align and place the palm-rest and keyboard assembly on the display assembly.

3. Using the alignment posts, close the display hinges.

4. Replace the two screws (M2.5x4) and (M2x3) that secure the left-display hinge to the system board.

5. Replace the two screws (M2.5x4) that secure the right-display hinge to the system board.

6. Connect the display cable on to the connector on the system board and adhere the tape to the system board.

Next steps

1. Install the WLAN card.

2. Install the battery.

3. Install the base cover.

4. Follow the procedure in after working inside your computer.

System board

Removing the system board - UMA

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

4. Remove the coin-cell battery.

80 Disassembly and reassembly

5. Remove the M.2 2280 solid-state drive.

6. Remove the M.2 2230 solid-state drive.

7. Remove the WLAN card.

8. Remove the system fan.

9. Remove the heat sink.

10. Remove the memory module.

11. Remove the display assembly.

About this task

The figure indicates the location of the system board and provides a visual representation of the removal procedure.

Disassembly and reassembly 81

Steps

1. Remove two screws (M2.5x4), and lift the left hinge.

2. Remove the transparent sticker covering the display cable to the system board.

3. Open the latch, and disconnect the display cable from the system board.

4. Remove the transparent sticker covering the DC-in port cable to the system board.

5. Disconnect the DC-in port cable from the system board.

6. Lift the mylar cover, and disconnect the fan cable.

7. Peel the adhesive tape, open the latch, and disconnect the I/O cable to the system board.

8. Remove the adhesive stickers.

9. Remove the two screws (M2x3) that secure the USB Type-C port bracket to the system board.

10. Disconnect the speaker cable from the system board.

11. Open the latch, and disconnect the touchpad cable from the system board.

12. Open the latch, and disconnect the keyboard-backlight cable from the system board.

13. Open the latch, and disconnect the keypad cable from the system board.

14. Remove two screws (M2x3) from the system board.

15. Gently release the ports on the system board from the slots on the palm-rest and keyboard assembly and lift the system

board off the palm-rest and keyboard assembly.

Installing the system board - UMA

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the system board and provides a visual representation of the installation procedure.

82 Disassembly and reassembly

Disassembly and reassembly 83

Steps

1. Slide the ports on the system board into the slots on the palm-rest and keyboard assembly and align the screw holes on the

system board with the screw holes on the palm-rest and keyboard assembly.

2. Replace the two screws (M2x3) that secure the system board to the palm-rest and keyboard assembly.

3. Connect the speaker cable to the system board.

4. Connect the touchpad cable to the system board and close the latch to secure the cable.

5. Connect the keyboard-backlight cable to the system board and close the latch to secure the cable.

6. Connect the keyboard cable to the system board and close the latch to secure the cable.

7. Replace the two screws (M2x3) that secure the USB Type-C port bracket to the system board.

8. Replace the adhesive sticker back.

9. Connect the fan cable onto the connector on the system board and close the latch.

10. Adhere the transparent sticker.

11. Lower the mylar flap.

12. Connect the I/O cable onto the connector on the system board and lower the latch.

13. Adhere the tape and transparent sticker that secures the I/O cable to the system board.

14. Connect the display cable onto the connector on the system board and lower the latch.

15. Adhere the tape and transparent sticker that secures the display cable to the system board.

16. Lower the right metal hinge, and replace the two screws (M2.5x4).

84 Disassembly and reassembly

Next steps

1. Install the display assembly.

2. Install the memory module.

3. Install the heat sink UMA (based on configuration).

4. Install the system fan.

5. Install the WLAN card.

6. Install the M.2 2230 solid-state drive.

7. Install the M.2 2280 solid-state drive.

8. Install the battery.

9. Install the base cover.

10. Follow the procedure in after working inside your computer.

Removing the system board - discrete

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

4. Remove the M.2 2280 solid-state drive.

5. Remove the M.2 2230 solid-state drive.

6. Remove the WLAN card.

7. Remove the system fan.

8. Remove the heat sink.

9. Remove the memory module.

10. Remove the display assembly.

About this task

The figure indicates the location of the system board and provides a visual representation of the removal procedure.

Disassembly and reassembly 85

86 Disassembly and reassembly

Steps

1. Remove two screws (M2.5x4), and lift the left hinge.

2. Remove the transparent sticker covering the display cable to the system board.

3. Open the latch, and disconnect the display cable from the system board.

4. Remove the transparent sticker covering the DC-in port cable to the system board.

5. Disconnect the DC-in port cable from the system board.

6. Lift the mylar cover, and disconnect the fan cable.

7. Peel the adhesive tape, open the latch, and disconnect the I/O cable to the system board.

8. Remove the adhesive stickers.

9. Remove the two screws (M2x3) that secure the USB Type-C port bracket to the system board.

10. Disconnect the speaker cable from the system board.

11. Open the latch, and disconnect the touchpad cable from the system board.

12. Open the latch, and disconnect the keyboard-backlight cable from the system board.

13. Open the latch, and disconnect the keypad cable from the system board.

14. Remove two screws (M2x3) from the system board.

15. Gently release the ports on the system board from the slots on the palm-rest and keyboard assembly and lift the system

board off the palm-rest and keyboard assembly.

Installing the system board - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the system board and provides a visual representation of the installation procedure.

Disassembly and reassembly 87

88 Disassembly and reassembly

Steps

1. Slide the ports on the system board into the slots on the palm-rest and keyboard assembly and align the screw holes on the

system board with the screw holes on the palm-rest and keyboard assembly.

2. Replace the two screws (M2x3) that secure the system board to the palm-rest and keyboard assembly.

3. Connect the speaker cable to the system board.

4. Connect the touchpad cable to the system board and close the latch to secure the cable.

5. Connect the keyboard-backlight cable to the system board and close the latch to secure the cable.

6. Connect the keyboard cable to the system board and close the latch to secure the cable.

7. Replace the two screws (M2x3) that secure the USB Type-C port bracket to the system board.

8. Replace the adhesive sticker back.

9. Connect the fan cable onto the connector on the system board.

10. Lower the mylar flap.

11. Connect the I/O cable onto the connector on the system board and lower the latch.

12. Adhere the tape that secures the I/O cable to the system board.

13. Connect the display cable onto the connector on the system board and lower the latch.

14. Adhere the tape that secures the display cable to the system board.

15. Lower the right metal hinge, and replace the two screws (M2.5x4).

Disassembly and reassembly 89

Next steps

1. Install the display assembly.

2. Install the memory module.

3. Install the heat sink - discrete or UMA (based on configuration).

4. Install the system fan.

5. Install the WLAN card.

6. Install the M.2 2230 solid-state drive.

7. Install the M.2 2280 solid-state drive.

8. Install the battery.

9. Install the base cover.

10. Follow the procedure in after working inside your computer.

Palm-rest and keyboard assembly

Removing the palm-rest and keyboard assembly - UMA

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery (3-cell or 4-cell).

4. Remove the WLAN card.

5. Remove the memory module.

6. Remove the M.2 2280 SSD.

7. Remove the M.2 2230 SSD.

8. Remove the system fan.

9. Remove the speaker (3-cell battery configuration or 4-cell battery configuration).

10. Remove the heat sink.

11. Remove the coin-cell battery.

12. Remove the I/O board.

13. Remove the power button with fingerprint reader.

14. Remove the DC-in port.

15. Remove the touchpad.

16. Remove the display assembly.

17. Remove the system board.

NOTE: The system board can be removed along with the heat sink.

About this task

The figure indicates the location of the palm-rest and keyboard assembly and provides a visual representation of the removal

procedure.

90 Disassembly and reassembly

Steps

After performing the steps in the pre-requisites, you are left with the palm-rest and keyboard assembly.

Installing the palm-rest and keyboard assembly - UMA

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the palm-rest and keyboard assembly and provides a visual representation of the installation

procedure.

Disassembly and reassembly 91

Steps

Place the palm-rest and keyboard assembly on a flat surface.

Next steps

1. Install the system board.

2. Install the touchpad.

3. Install the DC-in port.

4. Install the power button with fingerprint reader.

5. Install the coin-cell battery.

6. Install the heat sink.

7. Install the memory module.

8. Install the I/O board.

9. Install the display assembly.

10. Install the speakers (3-cell battery configuration or 4-cell battery configuration).

11. Install the system fan.

12. Install the M.2 2230 SSD card.

13. Install the M.2 2280 SSD card.

14. Install the WLAN card.

15. Install the battery (3-cell or 4-cell) based on the configuration.

16. Install the base cover.

17. Follow the procedure in after working inside your computer.

Removing the palm-rest and keyboard assembly - discrete

Prerequisites

1. Follow the procedure in before working inside your computer.

2. Remove the base cover.

3. Remove the battery (3-cell or 4-cell).

4. Remove the WLAN card.

5. Remove the memory module.

6. Remove the SSD-1 (M.2 2280 SSD or M.2 2230 SSD).

7. Remove the SSD-2.

92 Disassembly and reassembly

8. Remove the system fan.

9. Remove the heat sink discrete.

10. Remove the speaker (3-cell battery configuration or 4-cell battery configuration).

11. Remove the coin-cell battery.

12. Remove the I/O board.

13. Remove the power button with fingerprint reader.

14. Remove the DC-in port.

15. Remove the touchpad.

16. Remove the display assembly.

17. Remove the system board.

NOTE: The system board can be removed along with the heat sink.

About this task

The figure indicates the location of the palm-rest and keyboard assembly and provides a visual representation of the removal

procedure.

Steps

After performing the steps in the pre-requisites, you are left with the palm-rest and keyboard assembly.

Installing the palm-rest and keyboard assembly - discrete

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The figure indicates the location of the palm-rest and keyboard assembly and provides a visual representation of the installation

procedure.

Disassembly and reassembly 93

Steps

Place the palm-rest and keyboard assembly on a flat surface.

Next steps

1. Install the system board.

2. Install the touchpad.

3. Install the DC-in port.

4. Install the power button with fingerprint reader.

5. Install the I/O board.

6. Install the coin-cell battery.

7. Install the heat sink.

8. Install the display assembly.

9. Install the speakers (3-cell battery configuration or 4-cell battery configuration).

10. Install the system fan.

11. Install the SSD-1 (M.2 2230 SSD card or M.2 2280 SSD card).

12. Install the SSD-2 .

13. Install the memory modules.

14. Install the WLAN card.

15. Install the battery (3-cell or 4-cell) based on the configuration.

16. Install the base cover.

17. Follow the procedure in after working inside your computer.

94 Disassembly and reassembly

Software

This chapter details the supported operating systems along with instructions on how to install the drivers.

Topics:

•Downloading Windows drivers

Downloading Windows drivers

Steps

1. Turn on the notebook.

2. Go to Dell.com/support.

3. Click Product Support, enter the Service Tag of your notebook, and then click Submit.

NOTE: If you do not have the Service Tag, use the auto detect feature or manually browse for your notebook model.

4. Click Drivers and Downloads.

5. Select the operating system installed on your notebook.

6. Scroll down the page and select the driver to install.

7. Click Download File to download the driver for your notebook.

8. After the download is complete, navigate to the folder where you saved the driver file.

9. Double-click the driver file icon and follow the instructions on the screen.

Software 95

System setup

CAUTION: Unless you are an expert computer user, do not change the settings in the BIOS Setup program.

Certain changes can make your computer work incorrectly.

NOTE: Before you change BIOS Setup program, it is recommended that you write down the BIOS Setup program screen

information for future reference.

Use the BIOS Setup program for the following purposes:

●Get information about the hardware installed in your computer, such as the amount of RAM and the size of the hard drive.

●Change the system configuration information.

●Set or change a user-selectable option, such as the user password, type of hard drive installed, and enabling or disabling

base devices.

Topics:

•Boot menu

•Navigation keys

•Boot Sequence

•BIOS setup

•Updating the BIOS in Windows

•System and setup password

Boot menu

Press <F12> when the Dell logo appears to initiate a one-time boot menu with a list of the valid boot devices for the system.

Diagnostics and BIOS Setup options are also included in this menu. The devices listed on the boot menu depend on the bootable

devices in the system. This menu is useful when you are attempting to boot to a particular device or to bring up the diagnostics

for the system. Using the boot menu does not make any changes to the boot order stored in the BIOS.

The options are:

●UEFI Boot Devices:

○Windows Boot Manager

○UEFI Hard Drive

○Onboard NIC (IPV4)

○Onboard NIC (IPV6)

●Pre-Boot Tasks:

○BIOS Setup

○Diagnostics

○BIOS Update

○SupportAssist OS Recovery

○BIOS Flash Update - Remote

○Device Configuration

Navigation keys

NOTE: For most of the System Setup options, changes that you make are recorded but do not take effect until you restart

the system.

96 System setup

Keys Navigation

Up arrow Moves to the previous field.

Down arrow Moves to the next field.

Enter Selects a value in the selected field (if applicable) or follow the link in the field.

Spacebar Expands or collapses a drop-down list, if applicable.

Tab Moves to the next focus area.

Esc Moves to the previous page until you view the main screen. Pressing Esc in the main screen displays a

message that prompts you to save any unsaved changes and restarts the system.

Boot Sequence

Boot sequence enables you to bypass the System Setup–defined boot device order and boot directly to a specific device (for

example: optical drive or hard drive). During the Power-on Self-Test (POST), when the Dell logo appears, you can:

●Access System Setup by pressing F2 key

●Bring up the one-time boot menu by pressing F12 key.

The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot menu options

are:

●Removable Drive (if available)

●STXXXX Drive

NOTE: XXXX denotes the SATA drive number.

●Optical Drive (if available)

●SATA Hard Drive (if available)

●Diagnostics

NOTE: Choosing Diagnostics, displays the SupportAssist diagnostics screen.

The boot sequence screen also displays the option to access the System Setup screen.

BIOS setup

NOTE: Depending on the laptop and its installed devices, the items listed in this section may or may not appear.

Overview

Table 2. Overview

Option Description

System Information This section lists the primary hardware features of your

computer.

The options are:

●System Information

○BIOS version

○Service Tag

○Asset Tag

○Manufacture Date

○Ownership Date

○Express Service Code

○Ownership Tag

System setup 97

Table 2. Overview

Option Description

○Signed Firmware Update

●Battery

○Primary

○Battery Level

○Battery State

○Health

○AC Adapter

●Processor Information

○Processor Type

○Maximum Clock Speed

○Minimum Clock Speed

○Current Clock Speed

○Core Count

○Processor ID

○Processor L2 Cache

○Processor L3 Cache

○Microcode Version

○Intel Hyper-Threading Capable

○64-Bit Technology

●Memory Configuration

○Memory Installed

○Memory Available

○Memory Speed

○Memory Channel Mode

○Memory Technology

○DIMM_Slot 1

○DIMM_Slot 2

●Device Information

○Panel Type

○Video Controller

○Video Memory

○Wi-Fi Device

○Native Resolution

○Video BIOS Version

○Audio Controller

○Bluetooth Device

○LOM MAC Address

○dGPU Video Controller

Boot configuration

Table 3. Boot configuration

Option Description

Boot Sequence Allows you to change the order in which the computer

attempts to find an operating system.

The options are:

●Windows Boot Manager

●UEFI Hard Drive

98 System setup

Table 3. Boot configuration (continued)

Option Description

●Onboard NIC (IPV4)

●Onboard NIC (IPV6)

NOTE: Legacy Boot mode is not supported on this

platform.

Secure Boot Secure Boot helps ensure your system boots using only

validated boot software.

Enable Secure Boot—By default, this option is disabled.

NOTE: The system has to be in UEFI boot mode to enable

Enable Secure Boot.

Secure Boot Mode Changes to the Secure Boot operation mode modifies the

behavior of Secure Boot to allow evaluation of UEFI driver

signatures.

The options are:

●Deployed Mode—By default, this option is enabled.

●Audit Mode

Expert Key Management Allows you to enable or disable Expert Key Management.

Enable Custom Mode—By default, this option is disabled.

The Custom Mode Key Management options are:

●PK—By default, this option is enabled.

●KEK

●db

●dbx

Integrated Devices

Table 4. Integrated device options

Option Description

Date/Time Allows you to set the date and time. The change to the system

date and time takes effect immediately.

Camera Allows you to enable or disable camera.

Enable Camera - This option is enabled by default.

Audio Allows you to turn off all integrated audio. By default, the Enable

Audio option is selected.

Allows you to enable or disable the integrated audio or microphone

and speaker separately. By default, the Enable Audio option is

selected.

The options are:

●Enable Microphone

●Enable Internal Speaker

USB Configuration Allows you to enable or disable the internal or integrated USB

configuration.

The options are:

System setup 99

Table 4. Integrated device options (continued)

Option Description

●Enable USB Boot Support

●Enable External USB Port

By default, all the options are enabled.

Storage

Table 5. Storage options

Option Description

SATA Operation Allows you to configure the operating mode of the integrated

SATA hard drive controller.

The options are:

●Disabled

●AHCI

●RAID On—By default, the RAID On option is enabled.

NOTE: SATA is configured to support RAID mode.

Storage Interface Allows you to enable or disable various drives on board.

The options are:

●M.2 PCIe SSD-1

●M.2 PCIe SSD-0

By default, all the options are enabled.

SMART Reporting This field controls whether hard drive errors for integrated drives

are reported during system startup. This technology is part of the

Self Monitoring Analysis and Reporting Technology (SMART)

specification. By default, the Enable SMART Reporting option is

disabled .

Drive Information Provides information about drive type and device.

Display

Table 6. Display options

Option Description

Display Brightness Allows you to set the screen brightness when running on battery

and AC power.

The options are:

●Brightness on battery power - By default, set to 50.

●Brightness on AC power - By default, set to 100.

Full Screen Logo Displays full screen logo when the image matches screen

resolution.

By default, all the option is disabled.

100 System setup

Connection options

Table 7. Connection

Option Description

Integrated NIC Integrated NIC controls the onboard LAN controller. It allows

pre-OS and early operating system networking features to use

any enabled NICs when UEFI networking protocols are

installed and available.

The options are:

●Disabled

●Enabled

●Enabled with PXE - This option is enabled by default.

Wireless Device Enable Allows you to enable or disable the internal wireless devices.

The options are:

●WLAN

●Bluetooth

Both the options are enabled by default.

Enable UEFI Network Stack Allows you to control the onboard LAN controller. It allows

pre-OS and early operating system networking features to use

any enabled NICs when UEFI networking protocols are

installed and available.

Enable UEFI Network Stack - This option is enabled by

default.

Power management

Table 8. Power Management

Option Description

Battery Configuration Allows the system to run on battery during peak power usage hours.

The options are:

●Adaptive—enabled by default

●Standard

●ExpressCharge

●Primarily AC Use

●Custom

NOTE: If Custom Charge is selected, you can also configure Custom Charge Start and

Custom Charge Stop.

Advanced Configuration This option enables you to maximize the battery health.

By default, the Enable Advanced Battery Charge Mode option is disabled.

NOTE: The user can charge battery using feature Beginning of Day and Work Period.

By default, Work Period is disabled.

Use ExpressCharge for accelerated battery charging.

Peak Shift Allows the system to run on battery during peak power usage hours.

Peak Shift - By default, this option is disabled.

System setup 101

Table 8. Power Management (continued)

Option Description

NOTE: The user can:

●Set Battery Threshold Min = 15, Max = 100

●Prevent AC power between certain times of the day using Peak Shift Start, Peak Shift

End, and Peak Shift Charge Start.

Thermal Management Allows cooling of fans and the processor heat management to adjust system performance, noise,

and temperature.

The options are:

●Optimized—enabled by default

●Cool

●Quiet

●Ultra Performance

USB Wake Support Enable USB Wake

Support

Allows you to enable USB devices to wake the system from standby mode.

By default, the option Enable USB Wake Support is disabled.

Wake on Dell

USB-C Dock

Allows you to connect a Dell USB-C Dock to wake the system from

standby mode.

By default, the option Wake on Dell USB-C Dock is enabled.

NOTE: These features are only functional when the AC power adapter is connected. If the

AC power adapter is removed before Standby, the BIOS removes power from all USB ports to

conserve battery power.

Block Sleep This option enables you to block entering to sleep (S3) mode in operating system environment. By

default, the Block Sleep option is disabled.

NOTE: When Block Sleep is enabled, the system does not go to sleep. Intel Rapid Start gets

disabled automatically, and the operating system power option remains blank if it was set to

Sleep.

Lid Switch Allows you to disable the lid switch.

The options are:

●Enable Lid Switch—enabled by default

●Power On Lid Open—enabled by default

Intel Speed Shift

technology

Allows you to enable or disable the Intel Speed Shift Technology support. By default,Intel Speed

Shift technology is enabled. Enabling this option allows the operating system to select

appropriate processor performance.

Security

Table 9. Security

Option Description

TPM 2.0 Security Allows you to enable or disable the Trusted Platform Module (TPM).

The options are:

●TPM 2.0 Security On—This option is enabled by default.

●PPI Bypass for Enable Commands

●PPI Bypass for Disable Commands

●PPI Bypass for Clear Command

102 System setup

Table 9. Security (continued)

Option Description

●Attestation Enable—This option is enabled by default.

●Key Storage Enable—This option is enabled by default.

●SHA-256—This option is enabled by default.

●Clear

●TPM State—This option is enabled by default.

Intel Software Guard

Extensions

Provides a secure environment for running code or storing sensitive information in the context of

the main operating system and sets enclave reserve memory size.

Intel SGX

The options are:

●Disabled

●Enabled

●Software Control—This option is enabled by default.

SMM Security

Mitigation

Allows you to enable or disable additional UEFI SMM Security Mitigation protection.

SMM Security Mitigation - By default, this option is enabled.

Data Wipe on Next Boot Allows BIOS to queue up data wipe cycle for storage devices connected to the motherboard on

the next reboot.

Start Data Wipe - By default, this option is disabled.

NOTE: Secure Wipe operation deletes information in a way that it cannot be reconstructed.

Absolute This field allows you to Enable, Disable, or Permanently Disable the BIOS module interface of the

optional Absolute Persistence Module service from Absolute® Software.

The options are:

●Enable Absolute—This option is enabled by default.

●Disable Absolute

●Permanently Disable Absolute

UEFI Boot Path Security Controls whether the system prompts the user to enter the admin password (if set) when

booting to a UEFI boot path device from the F12 boot menu.

The options are:

●Never

●Always

●Always Except Internal HDD—This option is enabled by default.

●Always Except Internal HDD&PXE

Password

Table 10. Security

Option Description

Admin Password Allows you to set, change, or delete the administrator (admin) password.

The entries to set password are:

●Enter the old password:

●Enter the new password:

Press Enter once you enter the new password and again press Enter to confirm the new

password.

System setup 103

Table 10. Security (continued)

Option Description

NOTE: Deleting the admin password deletes the system password (if set). The admin

password can also be used to delete hard drive password. For this reason, you cannot set an

admin password if a system password or hard drive password is set. Hence, an admin

password has to be set first if the admin password has to be used with system password

and/or hard drive password.

System Password Allows you to set, change, or delete the system password.

The entries to set password are:

●Enter the old password:

●Enter the new password:

Press Enter once you enter the new password and again press Enter to confirm the new

password.

Password Configuration Allows you to configure a password.

Upper Case

Letter

When enabled, this field reinforces password must contain at least one

upper capital letter.

Lower Case

Letter

When enabled, this field reinforces password must contain at least one

lower capital letter.

Digit When enabled, this field reinforces password must contain at least one-

digit number.

Special

Character

When enabled, this field reinforces password must contain at least one

special character.

NOTE: These options by default are disabled.

Minimum

Characters

Defines the number of characters allowed for a password. Min = 4

Password Bypass Allows you to bypass the System password and the Internal hard drive password, when it is set,

during a system restart.

The options are:

●Disabled—This option is enabled by default.

●Reboot bypass

Password Changes Allows you to change the system password and hard drive password without the need of

administrator password.

Enable Non-Admin Password Changes - By default, this option is disabled.

Admin Setup Lockout Allows the administrator to control how the user can access BIOS setup.

Enable Admin Setup Lockout - By default, this option is disabled.

NOTE:

●If the admin password is set and Enable Admin Setup Lockoutis enabled, you cannot

view the BIOS setup (using F2 or F12) without the admin password.

●If the admin password is set and Enable Admin Setup Lockoutis disabled, the BIOS

setup can be entered and items that are viewed in Locked mode.

Master Password

Lockout

Allows you to disable master password support.

Enable Master Password Lockout - By default, this option is disabled.

NOTE: The Hard Disk password has to be cleared before the settings can be changed.

104 System setup

Update and Recovery

Table 11. Update and recovery

Option Description

UEFI Capsule Firmware

Updates

Allows you to update the system BIOS through UEFI capsule update packages.

Enable UEFI Capsule Firmware Updates - By default, this option is enabled.

BIOS Recovery from

Hard Drive

Allows you to recover BIOS on the primary hard drive or USB drive in corrupted conditions.

BIOS Recovery from Hard Drive - By default, this option is enabled.

NOTE: BIOS Recovery from hard drives is not available for Self-Encrypting Drives (SED).

BIOS Downgrade Allows you to control flashing of the system firmware to previous versions.

Allow BIOS Downgrade - By default, this option is enabled.

SupportAssist OS

Recovery

Allows you to enable or disable the boot flow for SupportAssist OS Recovery if there are certain

system errors.

SupportAssist OS Recovery - By default, this option is enabled.

NOTE: If SupportAssist OS Recovery setup option is disabled, then all the automatic boot

flow for SupportAssist OS Recovery tool is disabled.

BIOSConnect Allows you to recover cloud service operating system if the main operating system and/or local

service operating system fails to boot with the number of failures equal to or greater than the

value specified by the Auto operating system Recovery Threshold setup.

BIOSConnect - By default, this option is enabled.

Dell Auto OS Recovery

Threshold

The Auto OS Recovery threshold setup options control the automatic flow for SupportAssist

System Resolution Console and for Dell OS Recovery Tool.

The options are:

●Off

●1

●2 - Default

●3

System management

Table 12. System management

Option Description

Service Tag Displays the service tag of your computer.

Asset Tag An Asset Tag is a string of 64 characters that are used by IT administrator to uniquely identify a

particular system. On an asset tag is set, it cannot be changed.

AC Behavior Allows you to enable or disable the computer from turning on automatically when an AC adapter

is connected.

Wake on AC

By default, this option is disabled.

Auto On Time This setting allows a system to automatically power on for defined days/time.

The options are:

System setup 105

Table 12. System management (continued)

Option Description

●Disabled - This option is enabled by default.

●Every Day

●Weekdays

●Select Days

Keyboard

Table 13. Keyboard

Option Description

Numlock Enable Allows you to enable or disable Numlock function when the system boots.

Enable Numlock

This option is enabled by default.

Fn Lock Options Allows you to change the function key settings.

Fn Lock Mode

This option is enabled by default.

The options are:

●Lock Mode Standard

●Lock Mode Secondary- This option is enabled by default.

Keyboard Illumination Allows you to set keyboard illumination settings using hotkeys <Fn>+<F5> during normal system

operation.

The options are:

●Disabled

●Dim

●Bright- This option is enabled by default.

NOTE: The keyboard illumination brightness is set at 100%.

Keyboard Backlight

Timeout on AC

This feature defines the timeout value for the keyboard backlight when an AC adapter is plugged

in the system.

The options are:

●5 seconds

●10 seconds - This option is enabled by default.

●15 seconds

●30 seconds

●1 minute

●5 minutes

●15 minutes

●Never

NOTE: If Never is selected, the backlight stays on always when the system has AC adapter

plugged in.

Keyboard Backlight

Timeout on Battery

This feature defines the timeout value for the keyboard backlight when the system is running only

on battery power.

The options are:

●5 seconds

106 System setup

Table 13. Keyboard (continued)

Option Description

●10 seconds - This option is enabled by default.

●15 seconds

●30 seconds

●1 minute

●5 minutes

●15 minutes

●Never

NOTE: If Never is selected, the backlight stays on always when the system is running on

battery power.

Pre-boot behavior

Table 14. Pre-boot behavior

Option Description

Adapter Warnings This option displays warning messages during boot when adapters with little power capacity are

detected.

●Enable Adapter Warnings—enabled by default

Warnings and Errors This option causes the boot process to only pause when warnings and errors are detected rather

than stop, prompt, and wait for user input. This feature is useful where the system is being

remotely managed.

Select one of the following options:

●Prompt on Warnings and Errors—enabled by default

●Continue on Warnings

●Continue on Warnings and Errors

NOTE: Errors deemed critical to the operation of the system hardware always stop the

system.

USB-C Warnings This option enables or disables dock warning messages.

Enable Dock Warning Messages — enabled by default.

Fastboot This option allows you to configure the speed of UEFI boot process.

Select one of the following options:

●Minimal

●Thorough—enabled by default

●Auto

Extend BIOS POST Time This option allows you to configure the BIOS POST load time.

Select one of the following options:

●0 seconds—enabled by default.

●5 seconds

●10 seconds

Mouse/Touchpad This option defines how the system handles mouse and touchpad input.

Select one of the following options:

●Serial Mouse

●PS/2 Mouse

●Touchpad and PS/2 Mouse—enabled by default.

System setup 107

Virtualization support

Table 15. Virtualization Support

Option Description

Intel Virtualization

Technology

This option specifies whether the system can run on a Virtual Machine Monitor (VMM). By

default, the Enable Intel Virtualization Technology (VT) option is enabled.

VT for Direct I/O This option specifies whether the system can perform Virtualization technology for direct I/O;

an Intel method for virtualization for memory map I/O. By default, the Enable Intel VT for

Direct I/O option is enabled.

Performance

Table 16. Performance

Option Description

Multi Core Support This field specifies whether the process has one or all cores

enabled. The default value is set to the maximum number of

cores.

●All Cores — This option is enabled by default.

●1

●2

●3

Intel SpeedStep This feature allows the system to dynamically adjust processor

voltage and core frequency, decreasing average power

consumption and heat production.

Enable Intel SpeedStep

This option is enabled by default.

C-States Control This feature allows you to enable or disable the ability of the

CPU to enter and exit low-power states.

Enable C-state control

This option is enabled by default.

This feature allows the system to dynamically detect high

usage of discrete graphics and adjust system parameters for

higher performance during that time period.

Enable Adaptive C-states for Discrete Graphics

This option is enabled by default.

Intel Turbo Boost Technology This option allows you to enable or disable the Intel

TurboBoost mode of the processor.

Enable Intel Turbo Boost Technology

This option is enabled by default.

Intel Hyper-Threading Technology This option allows you to enable or disable the HyperThreading

in the processor.

Enable Intel Hyper-Threading Technology

This option is enabled by default.

108 System setup

System logs

Table 17. System Logs

Option Description

BIOS Event Log Allows you to either keep and clear the BIOS event log.

Clear BIOS Event Log

The options are:

●Keep - This option is enabled by default.

●Clear

Thermal Event Log Allows you to either keep and clear the Thermal event log.

Clear Thermal Event Log

The options are:

●Keep - This option is enabled by default.

●Clear

Power Event Log Allows you to either keep and clear the Power event log.

Clear Power Event Log

The options are:

●Keep - This option is enabled by default.

●Clear

Updating the BIOS in Windows

Prerequisites

It is recommended to update your BIOS (System Setup) when you replace the system board or if an update is available. For

laptops, ensure that your computer battery is fully charged and connected to a power before initiating a BIOS update.

About this task

NOTE: If BitLocker is enabled, it must be suspended prior to updating the system BIOS, and then re enabled after the BIOS

update is completed.

For more information about this subject, see Knowledge Article: How to Enable or Disable BitLocker with TPM in Windows.

Steps

1. Restart the computer.

2. Go to Dell.com/support.

●Enter the Service Tag or Express Service Code and click Submit.

●Click Detect Product and follow the instructions on screen.

3. If you are unable to detect or find the Service Tag, click Choose from all products.

4. Choose the Products category from the list.

NOTE: Choose the appropriate category to reach the product page.

5. Select your computer model and the Product Support page of your computer appears.

6. Click Get drivers and click Drivers and Downloads.

The Drivers and Downloads section opens.

7. Click Find it myself.

8. Click BIOS to view the BIOS versions.

9. Identify the latest BIOS file and click Download.

System setup 109

10. Select your preferred download method in the Please select your download method below window, click Download File.

The File Download window appears.

11. Click Save to save the file on your computer.

12. Click Run to install the updated BIOS settings on your computer.

Follow the instructions on the screen.

Updating BIOS on systems with BitLocker enabled

CAUTION: If BitLocker is not suspended before updating the BIOS, the next time you reboot the system it will

not recognize the BitLocker key. You will then be prompted to enter the recovery key to progress and the

system will ask for this on each reboot. If the recovery key is not known, this can result in data loss or an

unnecessary operating system reinstall. For more information about this subject, see Knowledge Article:

Updating the BIOS on Dell Systems With BitLocker Enabled

Updating the Dell BIOS in Linux and Ubuntu environments

If you want to update the system BIOS in a Linux environment, such as Ubuntu, see Update the Dell BIOS in a Linux or Ubuntu

environment.

Flashing the BIOS from the F12 One-Time boot menu

Updating your system BIOS using a BIOS update .exe file copied to a FAT32 USB key and booting from the F12 one time boot

menu.

About this task

BIOS Update

You can run the BIOS update file from Windows using a bootable USB key or you can also update the BIOS from the F12 One-

Time boot menu on the system.

Most Dell systems built after 2012 have this capability and you can confirm by booting your system to the F12 One-Time Boot

Menu to see if BIOS UPDATE is listed as a boot option for your system. If the option is listed, then the BIOS supports this BIOS

update option.

NOTE: Only systems with BIOS Flash Update option in the F12 One-Time Boot Menu can use this function.

Updating from the One-Time Boot Menu

To update your BIOS from the F12 One-Time boot menu, you need:

●USB key formatted to the FAT32 file system (key does not have to be bootable).

●BIOS executable file that you downloaded from the Dell Support website and copied to the root of the USB key.

●AC power adapter that is connected to the system.

●Functional system battery to flash the BIOS.

Perform the following steps to run the BIOS update flash process from the F12 menu:

CAUTION: Do not power off the system during the BIOS update process. Powering off the system could make

the system fail to boot.

Steps

1. From a power off state, insert the USB key where you copied the flash into a USB port of the system .

2. Power on the system and press the F12 key to access the One-Time Boot Menu.

3. Select BIOS Update using the mouse or arrow keys then press Enter.

110 System setup

The Flash BIOS opens.

4. Click Flash from file.

5. Select external USB device.

System setup 111

6. Once the file is selected, double-click the flash target file and click Submit.

7. Click Update BIOS for the system to reboot and flash the BIOS.

112 System setup

8. Once complete, the system reboots and the BIOS update process is completed.

System and setup password

Table 18. System and setup password

Password type Description

System password Password that you must enter to log on to your system.

Setup password Password that you must enter to access and make changes to

the BIOS settings of your computer.

You can create a system password and a setup password to secure your computer.

CAUTION: The password features provide a basic level of security for the data on your computer.

CAUTION: Anyone can access the data stored on your computer if it is not locked and left unattended.

NOTE: System and setup password feature is disabled.

Assigning a system setup password

Prerequisites

You can assign a new System or Admin Password only when the status is in Not Set.

About this task

To enter the system setup, press F2 immediately after a power-on or reboot.

Steps

1. In the System BIOS or System Setup screen, select Security and press Enter.

The Security screen is displayed.

System setup 113

2. Select System/Admin Password and create a password in the Enter the new password field.

Use the following guidelines to assign the system password:

●A password can have up to 32 characters.

●The password can contain the numbers 0 through 9.

●Only lower case letters are valid, upper case letters are not allowed.

●Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

3. Type the system password that you entered earlier in the Confirm new password field and click OK.

4. Press Esc and a message prompts you to save the changes.

5. Press Y to save the changes.

The computer reboots.

Deleting or changing an existing system setup password

Prerequisites

Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing

System and Setup password. You cannot delete or change an existing System or Setup password, if the Password Status is

Locked.

About this task

To enter the System Setup, press F2 immediately after a power-on or reboot.

Steps

1. In the System BIOS or System Setup screen, select System Security and press Enter.

The System Security screen is displayed.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password, alter or delete the existing system password and press Enter or Tab.

4. Select Setup Password, alter or delete the existing setup password and press Enter or Tab.

NOTE: If you change the System and/or Setup password, re enter the new password when prompted. If you delete the

System and Setup password, confirm the deletion when prompted.

5. Press Esc and a message prompts you to save the changes.

6. Press Y to save the changes and exit from System Setup.

The computer restarts.

114 System setup

Troubleshooting

Topics:

•Built-in self-test (BIST)

•System board built-in self-test (M-BIST)

•Display panel power rail built-in self-test (L-BIST)

•Display panel built-in self-test (LCD-BIST)

•Outcome

•SupportAssist diagnostics

•Running the SupportAssist diagnostics

•System diagnostic lights

•Recovering the operating system

•Flashing the BIOS

•Flashing BIOS (USB key)

•Backup media and recovery options

•WiFi power cycle

•Releasing Ethernet (RJ-45) cable

Built-in self-test (BIST)

About this task

There are three different types of BIST to check the performance of display, power rail, and system board. These tests are

important to evaluate if an LCD or System board needs a replacement.

1. M-Bist: M-BIST is the system board built-in self-test diagnostics tool that improves the diagnostics accuracy of system

board embedded controller (EC) failures. M-BIST must be manually initiated before POST and can also run on a dead

system .

2. L-BIST: L-BIST is an enhancement to the single LED error code diagnostics and is automatically initiated during POST.

3. LCD-BIST: LCD BIST is an enhanced diagnostic test that is introduced through Preboot System Assessment (PSA) on legacy

systems.

Table 19. Functions

M-Bist L-Bist

Purpose Evaluates the health condition of the

system board.

Checks if the system board is supplying

power to the LCD by performing an LCD

Power Rail test.

Trigger Press the <M> key and power button. Integrated into the single LED error code

diagnostics. Automatically initiated

during POST.

Indicator of fault Battery LED light with Solid Amber. Battery LED error code of [2,8] blinks

Amber x2, then pause, then blinks White

x8.

Repair instruction Indicates a problem with the system

board.

Indicates a problem with the system

board.

Troubleshooting 115

System board built-in self-test (M-BIST)

About this task

Steps

1. Press and hold both the M key and the power button to initiate M-BIST.

2. The battery-status light illuminates in amber when there is a system board failure.

3. Replace the system board to fix the issue.

NOTE: The battery status LED does not illuminate if the system board is functioning properly.

Display panel power rail built-in self-test (L-BIST)

About this task

Next steps

L-BIST (LCD Power Rail Test) is an enhancement to the single LED error code diagnostics and is automatically initiated

during POST. L-BIST isolates if the LCD is receiving power from the system board. L-BIST checks if the system board is

supplying power to the LCD by performing an LCD Power Rail test. If there is no power going to the LCD, the battery status

LED flashes a [2,8] LED error code.

116 Troubleshooting

Display panel power rail built-in self-test (L-BIST)

About this task

Next steps

L-BIST (LCD Power Rail Test) is an enhancement to the single LED error code diagnostics and is automatically initiated

during POST. L-BIST isolates if the LCD is receiving power from the system board. L-BIST checks if the system board is

supplying power to the LCD by performing an LCD Power Rail test. If there is no power going to the LCD, the battery status

LED flashes a [2,8] LED error code.

Display panel built-in self-test (LCD-BIST)

About this task

Steps

1. Press and hold the D key, and then press the power button.

2. Release both the D key and the power button when the computer begins POST.

3. The display panel begins to display a solid color, or cycling through different colors.

Troubleshooting 117

NOTE: The sequence of colors may vary depending on the different display panel vendors. The user only must ensure

that the colors are being displayed correctly without distortion or graphical anomalies.

4. The computer reboots at the end of the last solid color.

Outcome

About this task

The following table shows the outcome of running different types of BIST.

Table 20. BIST outcome

M-BIST

Off No fault detected with system board.

Solid amber Indicates a problem with the system board.

SupportAssist diagnostics

About this task

The SupportAssist diagnostics (previously known as ePSA diagnostics) performs a complete check of your hardware. The

SupportAssist diagnostics is embedded in the BIOS and is launched by it internally. The SupportAssist diagnostics provides a set

of options for particular devices or device groups. It allows you to:

●Run tests automatically or in an interactive mode

●Repeat tests

●Display or save test results

●Run thorough tests to introduce additional test options and provide extra information about the failed device(s)

●View status messages that indicate if the tests are completed successfully

●View error messages that indicate if problems were encountered during the test

NOTE: Some tests are meant for specific devices and require user interaction. Ensure that you are present in front of the

computer when the diagnostic tests are performed.

Running the SupportAssist diagnostics

Steps

1. Turn on your computer.

2. As the computer boots, press the F12 key as the Dell logo appears.

3. On the boot menu screen, select the Diagnostics option.

4. Click the arrow in the lower-right corner to go to the page listing.

The items that are detected are listed.

5. Select the device from the left cluster to run tests to run a diagnostic test on a specific device.

6. If there are any issues, error codes are displayed.

Note the error code and validation number and contact Dell.

System diagnostic lights

Battery-status light

Indicates the power and battery-charge status.

Solid white — Power adapter is connected and the battery has more than 5 percent charge.

118 Troubleshooting

Amber — Computer is running on battery and the battery has less than 5 percent charge.

Off

●Power adapter is connected, and the battery is fully charged.

●Computer is running on battery, and the battery has more than 5 percent charge.

●Computer is in sleep state, hibernation, or turned off.

The power and battery-status light blinks amber along with beep codes indicating failures.

For example, the power and battery-status light blinks amber two times followed by a pause, and then blinks white three times

followed by a pause. This 2,3 pattern continues until the computer is turned off indicating no memory or RAM is detected.

The following table shows different power and battery-status light patterns and associated problems.

Table 21. LED codes

Diagnostic light codes Problem description

1,1 TPM Detection Failure

1,2 Unrecoverable SPI Flash Failure

1,3 Short in hinge cable tripped OCP1

1,4 Short in hinge cable tripped OCP2

1, 5 EC unable to program i-Fuse

1, 6 Generic catch-all for ungraceful EC code flow

errors

2,1 Processor failure

2,2 System board: BIOS or ROM (Read-Only

Memory) failure

2,3 No memory or RAM (Random-Access Memory)

detected

2,4 Memory or RAM (Random-Access Memory)

failure

2,5 Invalid memory installed

2,6 System-board or chipset error

2,7 Display failure

2,8 LCD power rail failure.

3,1 Coin-cell battery failure

3,2 PCI, video card/chip failure

3,3 Recovery image not found

3,4 Recovery image found but invalid

3,5 Power-rail failure

3,6 System BIOS Flash incomplete

3,7 Timeout waiting on ME to reply to HECI

message

Camera status indicator: Indicates whether the camera is in use.

●Solid white — Camera is in use.

●Off — Camera is not in use.

Caps Lock status indicator: Indicates whether Caps Lock is enabled or disabled.

●Solid white — Caps Lock enabled.

●Off—Caps Lock disabled.

Troubleshooting 119

Recovering the operating system

When your computer is unable to boot to the operating system even after repeated attempts, it automatically starts Dell

SupportAssist OS Recovery.

Dell SupportAssist OS Recovery is a standalone tool that is preinstalled in all Dell computers installed with Windows 10 operating

system. It consists of tools to diagnose and troubleshoot issues that may occur before your computer boots to the operating

system. It enables you to diagnose hardware issues, repair your computer, back up your files, or restore your computer to its

factory state.

You can also download it from the Dell Support website to troubleshoot and fix your computer when it fails to boot into their

primary operating system due to software or hardware failures.

For more information about the Dell SupportAssist OS Recovery, see Dell SupportAssist OS Recovery User's Guide at

www.dell.com/support.

Flashing the BIOS

About this task

It is recommended to flash the BIOS when an update is available or when you replace the system board. To flash the BIOS:

Steps

1. Turn on your computer.

2. Go to www.dell.com/support.

3. Click Product support, enter the Service Tag of your computer, and then click Submit.

NOTE: If you do not have the Service Tag, use the Autodefect feature or manually browse for your computer model.

4. Click Drivers & downloads > Find it myself.

5. Select the operating system installed on your computer.

6. Scroll down the page, and expand BIOS.

7. Click Download to download the latest version of the BIOS for your computer.

8. After the download is complete, navigate to the folder where you saved the BIOS update file.

9. Double-click the BIOS update file icon, and follow the instructions on the screen.

Flashing BIOS (USB key)

Steps

1. Follow the procedure from step 1 to step 7 in "Flashing the BIOS" to download the latest BIOS setup program file.

2. Create a bootable USB drive. For more information, see the knowledge base article SLN143196 at www.dell.com/support.

3. Copy the BIOS setup program file to the bootable USB drive.

4. Connect the bootable USB drive to the computer that needs the BIOS update.

5. Restart the computer and press F12 when the Dell logo is displayed on the screen.

6. Boot to the USB drive from the One Time Boot Menu.

7. Type the BIOS setup program filename and press Enter.

8. The BIOS Update Utility appears. Follow the instructions on the screen to complete the BIOS update.

Backup media and recovery options

It is recommended to create a recovery drive to troubleshoot and fix problems that may occur with Windows. Dell proposes

multiple options for recovering Windows operating system on your Dell personal computer. For more information, see Dell

Windows Backup Media and Recovery Options.

120 Troubleshooting

WiFi power cycle

About this task

If your computer is unable to access the internet due to WiFi connectivity issues a WiFi power cycle procedure may be

performed. The following procedure provides the instructions on how to conduct a WiFi power cycle:

NOTE: Some ISPs (Internet Service Providers) provide a modem/router combo device.

Steps

1. Turn off your computer.

2. Turn off the modem.

3. Turn off the wireless router.

4. Wait for 30 seconds.

5. Turn on the wireless router.

6. Turn on the modem.

7. Turn on your computer.

Releasing Ethernet (RJ-45) cable

Prerequisites

Follow this procedure when disconnecting the ethernet (RJ-45) cable from the RJ-45 port to avoid damaging your computer.

Steps

1. Press down on the securing clip to release it from the port and pull the plug backward [1, 2].

2. Lift at an angle when disconnecting the ethernet cable from the RJ-45 port (Ethernet port) [3,4].

Troubleshooting 121

Getting help

Topics:

•Contacting Dell

Contacting Dell

Prerequisites

NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing

slip, bill, or Dell product catalog.

About this task

Dell provides several online and telephone-based support and service options. Availability varies by country and product, and

some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues:

Steps

1. Go to Dell.com/support.

2. Select your support category.

3. Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.

4. Select the appropriate service or support link based on your need.

122 Getting help

Table of Contents

DELL 5401 User Manual

Related Manuals