DELL 5410 User Manual

Displayed below is the user manual for 5410 by DELL which is a product in the Notebooks category. This manual has pages.

Related Manuals

DELL 5410 Manual

Inspiron 14 5410

Service Manual

Regulatory Model: P143G

Regulatory Type: P143G001

March 2021

Rev. A00

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

trademarks may be trademarks of their respective owners.

Chapter 1: Working inside your computer...................................................................................... 6

Before working inside your computer.............................................................................................................................6

Entering Service Mode.......................................................................................................................................................6

Safety instructions.............................................................................................................................................................. 6

Electrostatic discharge—ESD protection......................................................................................................................7

ESD field service kit ........................................................................................................................................................... 8

Transporting sensitive components................................................................................................................................ 9

Exiting Service Mode.......................................................................................................................................................... 9

After working inside your computer................................................................................................................................9

Chapter 2: Removing and installing components.......................................................................... 10

Recommended tools..........................................................................................................................................................10

Screw list............................................................................................................................................................................. 10

Major components of Inspiron 14 5410..........................................................................................................................11

Base cover........................................................................................................................................................................... 12

Removing the base cover...........................................................................................................................................12

Installing the base cover.............................................................................................................................................14

Battery cable.......................................................................................................................................................................15

Removing the 3-cell battery cable...........................................................................................................................15

Installing the 3-cell battery cable............................................................................................................................. 16

Removing the 4-cell battery cable........................................................................................................................... 17

Installing the 4-cell battery cable............................................................................................................................. 18

Battery..................................................................................................................................................................................19

Lithium-ion battery precautions............................................................................................................................... 19

Removing the 3-cell battery..................................................................................................................................... 20

Installing the 3-cell battery....................................................................................................................................... 20

Removing the 4-cell battery......................................................................................................................................21

Installing the 4-cell battery....................................................................................................................................... 22

Coin-cell battery................................................................................................................................................................ 23

Removing the coin-cell battery................................................................................................................................23

Installing the coin-cell battery.................................................................................................................................. 24

Solid-state drive................................................................................................................................................................ 25

Removing the M.2 2230 solid-state drive............................................................................................................. 25

Installing the M.2 2230 solid-state drive............................................................................................................... 26

Removing the M.2 2280 solid-state drive............................................................................................................. 27

Installing the M.2 2280 solid-state drive............................................................................................................... 28

Installing the solid-state drive mounting bracket................................................................................................ 29

Memory module.................................................................................................................................................................. 31

Removing the memory................................................................................................................................................ 31

Installing the memory................................................................................................................................................. 32

Wireless card...................................................................................................................................................................... 33

Removing the wireless card...................................................................................................................................... 33

Installing the wireless card........................................................................................................................................ 34

Power-adapter port.......................................................................................................................................................... 36

Contents

Contents 3

Removing the power-adapter port......................................................................................................................... 36

Installing the power-adapter port............................................................................................................................36

Display assembly................................................................................................................................................................ 37

Removing the display assembly................................................................................................................................37

Installing the display assembly..................................................................................................................................39

I/O board..............................................................................................................................................................................41

Removing the I/O board.............................................................................................................................................41

Installing the I/O board.............................................................................................................................................. 42

Speakers.............................................................................................................................................................................. 43

Removing the speakers..............................................................................................................................................43

Installing the speakers................................................................................................................................................ 44

Touchpad.............................................................................................................................................................................45

Removing the touchpad.............................................................................................................................................45

Installing the touchpad...............................................................................................................................................46

Fan........................................................................................................................................................................................ 47

Removing the fan........................................................................................................................................................ 47

Installing the fan.......................................................................................................................................................... 48

Heat sink..............................................................................................................................................................................49

Removing the heat sink............................................................................................................................................. 49

Installing the heat sink............................................................................................................................................... 50

Power button with optional fingerprint reader........................................................................................................... 51

Removing the power-button with optional fingerprint reader.......................................................................... 51

Installing the power-button with optional fingerprint reader............................................................................ 51

System board..................................................................................................................................................................... 52

Removing the system board..................................................................................................................................... 52

Installing the system board....................................................................................................................................... 55

Palm-rest and keyboard assembly................................................................................................................................ 59

Removing the palm-rest and keyboard assembly................................................................................................59

Installing the palm-rest and keyboard assembly.................................................................................................. 60

Chapter 3: Drivers and downloads............................................................................................... 62

Chapter 4: System setup............................................................................................................. 63

Entering BIOS setup program........................................................................................................................................ 63

Navigation keys..................................................................................................................................................................63

Boot Sequence...................................................................................................................................................................64

System setup options.......................................................................................................................................................64

Updating the BIOS in Windows .................................................................................................................................... 68

Updating BIOS on systems with BitLocker enabled........................................................................................... 69

Updating your system BIOS using a USB flash drive..........................................................................................69

Flashing the BIOS from the F12 One-Time boot menu............................................................................................ 70

System and setup password...........................................................................................................................................73

Assigning a system setup password....................................................................................................................... 73

Deleting or changing an existing system setup password................................................................................. 74

Clearing CMOS settings.............................................................................................................................................74

Clearing BIOS (System Setup) and System passwords.....................................................................................75

Chapter 5: Troubleshooting......................................................................................................... 76

Locate the Service Tag or Express Service Code of your Dell computer ..............................................76

4Contents

System-diagnostic lights................................................................................................................................................. 76

SupportAssist | On-board Diagnostics......................................................................................................................... 77

Recovering the operating system..................................................................................................................................78

Flashing BIOS (USB key).................................................................................................................................................78

Flashing the BIOS.............................................................................................................................................................. 78

WiFi power cycle............................................................................................................................................................... 79

Chapter 6: Getting help and contacting Dell................................................................................ 80

Contents 5

Working inside your computer

Before working inside your computer

About this task

NOTE: The images in this document may differ from your computer depending on the configuration you ordered.

Steps

1. Save and close all open files and exit all open applications.

2. Shut down your computer. Click Start > Power > Shut down.

NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down

instructions.

3. Disconnect your computer and all attached devices from their electrical outlets.

4. Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.

CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the

cable from the network device.

5. Remove any media card and optical disc from your computer, if applicable.

Entering Service Mode

Service Mode allows users to immediately cut off electricity from the computer and conduct repairs without disconnecting the

battery cable from the system board.

To enter Service Mode:

1. Shut down your computer and disconnect the AC adapter.

2. Hold <B> key on the keyboard and press the power button for 3 seconds or until the Dell logo appears on the screen.

3. Press any key to continue.

NOTE: If the power adapter has not been disconnected, a message prompting you to remove the AC adapter appears

on the screen. Remove the AC adapter and then press any key to continue the Service Mode procedure.

NOTE: The Service Mode procedure automatically skips the following step if the Owner Tag of the computer is not

set up in advance by the manufacturer.

4. When the ready-to-proceed message appears on the screen, press any key to proceed. The computer emits three short

beeps and shuts down immediately.

Once the computer shuts down, you may perform the replacement procedures without disconnecting the battery cable from

the system board.

Safety instructions

Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless

otherwise noted, each procedure included in this document assumes that you have read the safety information that shipped

with your computer.

6 Working inside your computer

WARNING: Before working inside your computer, read the safety information that is shipped with your

computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/

regulatory_compliance.

WARNING: Disconnect your computer from all power sources before opening the computer cover or panels.

After you finish working inside the computer, replace all covers, panels, and screws before connecting your

computer to an electrical outlet.

CAUTION: To avoid damaging the computer, ensure that the work surface is flat, dry, and clean.

CAUTION: To avoid damaging the components and cards, handle them by their edges, and avoid touching the

pins and the contacts.

CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical

assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the

safety instructions that is shipped with the product or at www.dell.com/regulatory_compliance.

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal

surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal

surface to dissipate static electricity which could harm internal components.

CAUTION: When you disconnect a cable, pull it by its connector or its pull tab, not the cable itself. Some cables

have connectors with locking tabs or thumbscrews that you must disengage before disconnecting the cable.

When disconnecting cables, keep them evenly aligned to avoid bending the connector pins. When connecting

cables, ensure that the ports and the connectors are correctly oriented and aligned.

CAUTION: Press and eject any installed card from the media-card reader.

NOTE: The color of your computer and certain components may appear differently than shown in this document.

Electrostatic discharge—ESD protection

ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards,

processors, memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such

as intermittent problems or a shortened product life span. As the industry pushes for lower power requirements and increased

density, ESD protection is an increasing concern.

Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than

in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.

Two recognized types of ESD damage are catastrophic and intermittent failures.

●Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes

an immediate and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has

received a static shock and immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or

nonfunctional memory.

●Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of

intermittent failures means that most of the time when damage occurs, it is not immediately recognizable. The DIMM

receives a static shock, but the tracing is merely weakened and does not immediately produce outward symptoms related to

the damage. The weakened trace may take weeks or months to melt, and in the meantime may cause degradation of memory

integrity, intermittent memory errors, etc.

The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded")

failure.

Perform the following steps to prevent ESD damage:

●Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do not

provide adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts

with increased sensitivity to ESD damage.

●Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.

●When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static

packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you

discharge static electricity from your body.

Working inside your computer 7

●Before transporting a static-sensitive component, place it in an anti-static container or packaging.

ESD field service kit

The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components:

anti-static mat, wrist strap, and bonding wire.

Components of an ESD field service kit

The components of an ESD field service kit are:

●Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an

anti-static mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal

on the system being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly

on the mat. ESD-sensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.

●Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist

and bare metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that

is temporarily placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD

mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never

use wireless wrist straps. Always be aware that the internal wires of a wrist strap are prone to damage from normal wear

and tear, and must be checked regularly with a wrist strap tester in order to avoid accidental ESD hardware damage. It is

recommended to test the wrist strap and bonding wire at least once per week.

●ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored

kit, it is a best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A

wrist strap tester is the best method for doing this test. If you do not have your own wrist strap tester, check with your

regional office to find out if they have one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is

strapped to your wrist and push the button to test. A green LED is lit if the test is successful; a red LED is lit and an alarm

sounds if the test fails.

●Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts

that are insulators and often highly charged.

●Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For

example, deploying the kit for a server environment is different than for a desktop or portable environment. Servers are

typically installed in a rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always

look for a large open flat work area that is free of clutter and large enough to deploy the ESD kit with additional space to

accommodate the type of system that is being repaired. The workspace should also be free of insulators that can cause an

ESD event. On the work area, insulators such as Styrofoam and other plastics should always be moved at least 12 inches or

30 centimeters away from sensitive parts before physically handling any hardware components

●ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded

bags are preferred. However, you should always return the damaged part using the same ESD bag and packaging that the

new part arrived in. The ESD bag should be folded over and taped shut and all the same foam packing material should be

used in the original box that the new part arrived in. ESD-sensitive devices should be removed from packaging only at an

ESD-protected work surface, and parts should never be placed on top of the ESD bag because only the inside of the bag is

shielded. Always place parts in your hand, on the ESD mat, in the system, or inside an anti-static bag.

●Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts

to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.

ESD protection summary

It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static

mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all

insulator parts while performing service and that they use anti-static bags for transporting sensitive components.

8Working inside your computer

Transporting sensitive components

When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place

these parts in anti-static bags for safe transport.

Lifting equipment

Adhere to the following guidelines when lifting heavy weight equipment:

CAUTION: Do not lift greater than 50 pounds. Always obtain additional resources or use a mechanical lifting

device.

1. Get a firm balanced footing. Keep your feet apart for a stable base, and point your toes out.

2. Tighten stomach muscles. Abdominal muscles support your spine when you lift, offsetting the force of the load.

3. Lift with your legs, not your back.

4. Keep the load close. The closer it is to your spine, the less force it exerts on your back.

5. Keep your back upright, whether lifting or setting down the load. Do not add the weight of your body to the load. Avoid

twisting your body and back.

6. Follow the same techniques in reverse to set the load down.

Exiting Service Mode

Service Mode allows users to immediately cut off electricity from the computer and conduct repairs without disconnecting the

battery cable from the system board.

To exit Service Mode:

1. Connect the AC adapter to the power-adapter port on your computer.

2. Press the power button to turn on the computer. Your computer will automatically return to normal functioning mode.

After working inside your computer

About this task

CAUTION: Leaving stray or loose screws inside your computer may severely damage your computer.

Steps

1. Replace all screws and ensure that no stray screws remain inside your computer.

2. Connect any external devices, peripherals, or cables you removed before working on your computer.

3. Replace any media cards, discs, or any other parts that you removed before working on your computer.

4. Connect your computer and all attached devices to their electrical outlets.

5. Turn on your computer.

Working inside your computer 9

Removing and installing components

NOTE: The images in this document may differ from your computer depending on the configuration you ordered.

Recommended tools

The procedures in this document may require the following tools:

●Phillips screwdriver #1

●Plastic scribe

Screw list

NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and

then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type is

restored when the component is replaced.

NOTE: Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surfaces when

replacing a component.

NOTE: Screw color may vary with the configuration ordered.

Table 1. Screw list

Component Secured to Screw type Quantity Screw image

Base cover Palm-rest and keyboard

assembly

M2x4 5

Base cover Palm-rest and keyboard

assembly

M2x7 (captive) 2

Battery Palm-rest and keyboard

assembly

M2x3 ●3-cell: 4

●4-cell: 5

Solid-state drive Palm-rest and keyboard

assembly

M2x3 1 per solid-state

drive

Fan Palm-rest and keyboard

assembly

M2x2 2

Wireless-card bracket System board M2x4 1

Touchpad Palm-rest and keyboard

assembly

M2x1.8 2

Touchpad bracket Palm-rest and keyboard

assembly

M1.6x2 3

Power-button with

optional fingerprint

reader

Palm-rest and keyboard

assembly

M2x3 1

10 Removing and installing components

Table 1. Screw list

Component Secured to Screw type Quantity Screw image

Power-adapter port Palm-rest and keyboard

assembly

M2x3 1

Type-C port bracket System board M2x4 2

Display hinges Palm-rest and keyboard

assembly

M2.5x4 4

I/O board Palm-rest and keyboard

assembly

M2x3 1

System board Palm-rest and keyboard

assembly

M2x2 2

Major components of Inspiron 14 5410

The following image shows the major components of Inspiron 14 5410.

Removing and installing components 11

1. Base cover

2. Heat sink

3. System board

4. Memory

5. Battery

6. Right speaker

7. Palm-rest and keyboard assembly

8. Touchpad

9. Display assembly

10. Left speaker

11. Coin-cell battery

12. I/O board

13. M.2 2280 solid-state drive, if installed

14. Wireless card

15. M.2 2230 solid-state drive, if installed

16. Power-button with optional fingerprint-reader

17. Fan

18. Power-adapter port

NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These

parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative for

purchase options.

Base cover

Removing the base cover

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

About this task

NOTE: Before removing the base cover, ensure that there is no micro-SD card installed in the micro-SD card slot on your

computer.

The following image(s) indicate the location of the base cover and provides a visual representation of the removal procedure.

12 Removing and installing components

Removing and installing components 13

Steps

1. Remove the five screws (M2x4) that secure the base cover to the palm-rest and keyboard assembly.

2. Loosen the two captive screws that secure the base cover to the palm-rest and keyboard assembly.

3. Using a plastic scribe, pry the base cover from the bottom left and continue to work on the sides to open the base cover.

4. Lift the base cover off the palm-rest and keyboard assembly.

Installing the base cover

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image(s) indicate the location of the base cover and provides a visual representation of the installation procedure.

14 Removing and installing components

Steps

1. Place and snap the base cover into place on the palm-rest and keyboard assembly.

2. Tighten the two captive screws that secure the base cover to the palm-rest and keyboard assembly.

3. Replace the five screws (M2x4) that secure the base cover to the palm-rest and keyboard assembly.

Next steps

1. Exit Service Mode.

2. Follow the procedure in After working inside your computer.

Battery cable

Removing the 3-cell battery cable

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Remove the base cover.

About this task

The following image(s) indicate the location of the 3-cell battery cable and provides a visual representation of the removal

procedure.

Removing and installing components 15

Steps

1. Peel the tape that secures the battery cable to the 3-cell battery.

2. Disconnect the battery cable from the system board.

3. Remove the battery cable from the routing guides on the 3-cell battery.

4. Disconnect the battery cable from the 3-cell battery.

5. Lift the battery cable off the 3-cell battery.

Installing the 3-cell battery cable

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image(s) indicate the location of the 3-cell battery cable and provides a visual representation of the installation

procedure.

16 Removing and installing components

Steps

1. Connect the battery cable to the 3-cell battery.

2. Route the battery cable through the routing guides on the 3-cell battery.

3. Connect the battery cable to the system board.

4. Adhere the tape that secures the battery cable to the 3-cell battery.

Next steps

1. Install the base cover.

2. Follow the procedure in After working inside your computer.

Removing the 4-cell battery cable

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Remove the base cover.

About this task

The following image(s) indicate the location of the 4-cell battery cable and provides a visual representation of the removal

procedure.

Removing and installing components 17

Steps

1. Peel the tape that secures the battery cable to the 4-cell battery.

2. Disconnect the battery cable from the system board.

3. Remove the battery cable from the routing guides on the 4-cell battery.

4. Disconnect the battery cable from the 4-cell battery.

5. Lift the battery cable off the 4-cell battery.

Installing the 4-cell battery cable

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image(s) indicate the location of the 4-cell battery cable and provides a visual representation of the installation

procedure.

18 Removing and installing components

Steps

1. Connect the battery cable to the 4-cell battery.

2. Route the battery cable through the routing guides on the 4-cell battery.

3. Connect the battery cable to the system board.

4. Adhere the tape that secures the battery cable to the 4-cell battery.

Next steps

1. Install the base cover.

2. Follow the procedure in After working inside your computer.

Battery

Lithium-ion battery precautions

CAUTION:

●Exercise caution when handling Lithium-ion batteries.

●Discharge the battery completely before removing it. Disconnect the AC power adapter from the system and

operate the computer solely on battery power—the battery is fully discharged when the computer no longer

turns on when the power button is pressed.

●Do not crush, drop, mutilate, or penetrate the battery with foreign objects.

●Do not expose the battery to high temperatures, or disassemble battery packs and cells.

●Do not apply pressure to the surface of the battery.

●Do not bend the battery.

●Do not use tools of any kind to pry on or against the battery.

●Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental

puncture or damage to the battery and other system components.

Removing and installing components 19

●If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing,

bending, or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical

support for assistance. See www.dell.com/contactdell.

●Always purchase genuine batteries from www.dell.com or authorized Dell partners and resellers.

Removing the 3-cell battery

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Remove the base cover.

About this task

The following image(s) indicate the location of the 3-cell battery and provides a visual representation of the removal procedure.

Steps

1. Peel the tape that secures the battery cable to the 3-cell battery.

2. Disconnect the battery cable from the system board.

3. Remove the three screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.

4. Lift the battery off the palm-rest and keyboard assembly.

Installing the 3-cell battery

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image(s) indicate the location of the 3-cell battery and provides a visual representation of the installation

procedure.

20 Removing and installing components

Steps

1. Align the screw holes on the battery with the screw holes on the palm-rest and keyboard assembly.

2. Replace the three screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.

3. Connect the battery cable to the system board.

4. Adhere the tape that secures the battery cable to the 3-cell battery.

Next steps

1. Install the base cover.

2. Follow the procedure in After working inside your computer.

Removing the 4-cell battery

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Remove the base cover.

About this task

The following image(s) indicate the location of the 4-cell battery and provides a visual representation of the removal procedure.

Removing and installing components 21

Steps

1. Peel the tape that secures the battery cable to the 4-cell battery.

2. Disconnect the battery cable from the system board, if applicable.

3. Remove the five screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.

4. Lift the battery off the palm-rest and keyboard assembly.

Installing the 4-cell battery

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image(s) indicate the location of the 4-cell battery and provides a visual representation of the installation

procedure.

22 Removing and installing components

Steps

1. Align the screw holes on the battery with the screw holes on the palm-rest and keyboard assembly.

2. Replace the five screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.

3. Connect the battery cable to the system board.

4. Adhere the tape that secures the battery cable to the 4-cell battery.

Next steps

1. Install the base cover.

2. Follow the procedure in After working inside your computer.

Coin-cell battery

Removing the coin-cell battery

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

About this task

The following image(s) indicate the location of the coin-cell battery and provides a visual representation of the removal

procedure.

Removing and installing components 23

Steps

1. Disconnect the coin-cell battery from the I/O board.

2. Peel and lift the coin-cell battery from the palm-rest and keyboard assembly.

Installing the coin-cell battery

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image(s) indicate the location of the coin-cell battery and provides a visual representation of the installation

procedure.

24 Removing and installing components

Steps

1. Connect the coin-cell battery cable to the I/O board.

2. Adhere the coin-cell battery to the palm-rest and keyboard assembly.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

Solid-state drive

Removing the M.2 2230 solid-state drive

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

About this task

NOTE: This procedure applies only to computers shipped with an M.2 2230 solid-state drive installed.

NOTE: The M.2 card installed on your computer will depend on the configuration ordered. Supported card configurations on

the M.2 card slot:

●M.2 2230 solid-state drive

Removing and installing components 25

●M.2 2280 solid-state drive

The following image(s) indicate the location of the M.2 2230 solid-state drive and provides a visual representation of the

removal procedure.

Steps

1. Remove the screw (M2x3) that secures the M.2 2230 solid-state drive to the system board.

2. Slide and lift the M.2 2230 solid-state drive off the system board.

3. Slide and lift the M.2 2230 solid-state drive off the system board.

Installing the M.2 2230 solid-state drive

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

NOTE: This procedure applies if you are installing a M.2 2230 solid-state drive.

NOTE: The M.2 card installed on your computer will depend on the configuration ordered. Supported card configurations on

the M.2 card slot:

●M.2 2230 solid-state drive + M.2 2230 solid-state drive mounting bracket

●M.2 2280 solid-state drive

The following image(s) indicate the location of the M.2 2230 solid-state drive and provides a visual representation of the

installation procedure.

26 Removing and installing components

Steps

1. Align the notch on the M.2 2230 solid-state drive with the tab on the M.2 card slot on the system board.

2. Slide the M.2 2230 solid-state drive into the M.2 card slot on the system board.

3. Replace the screw (M2x3) that secures the M.2 2230 solid-state drive to the system board.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

Removing the M.2 2280 solid-state drive

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

About this task

NOTE: This procedure applies only to computers shipped with a M.2 2280 solid-state drive installed.

NOTE: The M.2 card installed on your computer will depend on the configuration ordered. Supported card configurations on

the M.2 card slot:

●M.2 2230 solid-state drive

●M.2 2280 solid-state drive

The following image(s) indicate the location of the M.2 2280 solid-state drive and provides a visual representation of the

removal procedure.

Removing and installing components 27

Steps

1. Remove the screw (M2x3) that secures the M.2 2280 solid-state drive to the palm-rest and keyboard assembly.

2. Slide and remove the M.2 2280 solid-state drive from the M.2 card slot on the system board.

Installing the M.2 2280 solid-state drive

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

NOTE: This procedure applies if you are installing a M.2 2280 solid-state drive.

NOTE: The M.2 card installed on your computer will depend on the configuration ordered. Supported card configurations on

the M.2 card slot:

●M.2 2230 solid-state drive

●M.2 2280 solid-state drive

The following image(s) indicate the location of the M.2 2280 solid-state drive and provides a visual representation of the

installation procedure.

28 Removing and installing components

Steps

1. Align the notch on the M.2 2280 solid-state drive with the tab on the M.2 card slot on the system board.

2. Slide the M.2 2280 solid-state drive into the M.2 card slot on the system board.

3. Replace the screw (M2x3) that secures the M.2 2280 solid-state drive to the palm-rest and keyboard assembly.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

Installing the solid-state drive mounting bracket

About this task

The following image provides a visual representation of the procedure to install the solid-state drive mounting bracket when

replacing a M.2 2230 solid-state drive with a M.2 2280 solid-state drive.

Removing and installing components 29

The following image provides a visual representation of the procedure to install the solid-state drive mounting bracket when

replacing a M.2 2280 solid-state drive with a M.2 2230 solid-state drive.

Steps

1. Remove the 2230 solid-state drive or 2280 solid-state drive, whichever applicable.

2. Peel the Mylar that covers the solid-state drive mounting-bracket and mounting-bracket slot.

3. Slide and remove the solid-state drive mounting-bracket from the mounting-bracket slot on the palm-rest and keyboard

assembly.

4. Rotate the solid-state drive mounting-bracket.

5. Slide the solid-state mounting-bracket into the mounting-bracket slot on the palm-rest and keyboard assembly.

6. Adhere the Mylar that covers the solid-state drive mounting-bracket and mounting-bracket slot.

7. Install the 2230 solid-state drive or 2280 solid-state drive, whichever applicable.

30 Removing and installing components

Memory module

Removing the memory

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

About this task

The following image(s) indicate the location of the memory and provides a visual representation of the removal procedure.

Steps

1. Lift the Mylar to access the memory module.

2. Using your fingertips, carefully spread apart the securing-clips on each end of the memory-module slot until the memory

module pops-up.

3. Remove the memory module from the memory-module slot on the system board.

Removing and installing components 31

NOTE: Your computer may have up to two memory modules installed. Repeat steps 1 to 3 if there is a second memory

module installed.

Installing the memory

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image(s) indicate the location of the memory and provides a visual representation of the installation procedure.

Steps

1. Lift the Mylar to access the memory-module slot.

2. Align the notch on the memory module with the tab on the memory-module slot on the system board.

3. Slide the memory module into the memory-module slot on the system board.

4. Press down on the memory module till the securing clips click, locking the memory module in place.

32 Removing and installing components

NOTE: Repeat steps 1 to 4 for each memory module being installed into your computer.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

Wireless card

Removing the wireless card

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

About this task

The following image(s) indicate the location of the wireless card and provides a visual representation of the removal procedure.

Removing and installing components 33

Steps

1. Remove the screw (M2x4) that secures the wireless-card bracket to the wireless card and system board.

2. Lift the wireless-card bracket off the wireless card.

3. Disconnect the antenna cables from the wireless card.

4. Slide and remove the wireless card from the M.2 card slot on the system board.

Installing the wireless card

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image(s) indicate the location of the wireless card and provides a visual representation of the installation

procedure.

34 Removing and installing components

Steps

1. Connect the antenna cables to the wireless card.

Table 2. Antenna-cable color scheme

Connectors on the

wireless card

Antenna-cable color Silkscreen marking

Main White MAIN △ (white triangle)

Auxiliary Black AUX ▲ (black triangle)

2. Place the wireless-card bracket on the wireless card.

3. Align the notch on the wireless card with the tab on the M.2 card slot on the system board.

4. Slide the wireless card into the M.2 card slot on the system board.

5. Replace the screw (M2x4) that secures the wireless card and wireless-card bracket to the system board.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

Removing and installing components 35

Power-adapter port

Removing the power-adapter port

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

About this task

The following image(s) indicate the location of the power-adapter port and provides a visual representation of the removal

procedure.

Steps

1. Remove the two screws (M2.5x4) that secures the right-display hinge to the system board.

2. Pry open the right-display hinge at an angle of 90 degrees.

3. Peel the tape that covers the power-adapter port connector on the system board.

4. Disconnect the power-adapter port from the system board.

5. Remove the power-adapter port cable from the routing guides on the palm-rest and keyboard assembly.

6. Remove the power-adapter port from the palm-rest and keyboard assembly.

Installing the power-adapter port

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image(s) indicate the location of the power-adapter port and provides a visual representation of the installation

procedure.

36 Removing and installing components

Steps

1. Connect the power-adapter port cable to the system board.

2. Adhere the tape that covers the power-adapter port connector on the system board.

3. Route the power-adapter port cable through the routing guides on the palm-rest and keyboard assembly.

4. Place the power-adapter port into the slot on the palm-rest and keyboard assembly.

5. Close the right-display hinge and align the screw holes on the right-display hinge with the screw holes on the system board.

6. Replace the two screws (M2.5x4) that secures the right-display hinge to the system board.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

Display assembly

Removing the display assembly

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

About this task

The following image(s) indicate the location of the display assembly and provides a visual representation of the removal

procedure.

Removing and installing components 37

38 Removing and installing components

Steps

1. Peel the tape that secures the display-cable connector latch to the system board.

2. Lift the latch and disconnect the display-cable from the connector on the system board.

3. Remove the two screws (M2.5x4) that secure the right-display hinge to the system board.

4. Pry open the right-display hinge at an angle of 90 degrees.

5. Remove the two screws (M2.5x4) that secure the left-display hinge to the I/O board.

6. Pry open the left-display hinge at an angle of 90 degrees.

7. Gently lift the palm-rest and keyboard assembly off the display assembly

CAUTION: To avoid damaging the display, do not slide the palm-rest and keyboard assembly over the display

assembly.

Installing the display assembly

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image(s) indicate the location of the display assembly and provides a visual representation of the installation

procedure.

Removing and installing components 39

Steps

1. Place the display assembly on a clean and flat surface with the display panel facing up.

2. Gently place the palm-rest and keyboard assembly under the display hinges.

CAUTION: To avoid damaging the display, do not slide the palm-rest and keyboard assembly over the display

assembly.

3. Close the left-display hinge and align the screw holes on the left-display hinge with the screw holes on the I/O board.

4. Replace the two screws (M2.5x4) that secure the left-display hinge to the palm-rest and keyboard assembly.

5. Close the right-display hinge and align the screw holes on the right-display hinge with the screw holes on the system board.

6. Replace the two screws (M2.5x4) that secure the right-display hinge to the palm-rest and keyboard assembly.

7. Connect the display cable to the connector on the system board and close the latch.

8. Adhere the tape that secures the display-cable connector latch to the system board.

40 Removing and installing components

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

I/O board

Removing the I/O board

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

About this task

The following image(s) indicate the location of the I/O board and provides a visual representation of the removal procedure.

Steps

1. Remove the two screws (M2.5x4) that secure the left-display hinge to the I/O board.

2. Pry open the left-display hinge at an angle of 90 degrees.

3. Lift the I/O-board cable-connector latch and disconnect the I/O-board cable from the I/O board.

4. Lift the power-button with fingerprint-reader cable-connector latch and disconnect the power-button with fingerprint-

reader cable from the I/O board.

NOTE: This step is only applicable for computers shipped with the optional fingerprint reader.

5. Remove the screw (M2x3) that secures the I/O board to the palm-rest and keyboard assembly.

6. Disconnect the coin-cell battery cable from the I/O board.

7. Lift the I/O board off the palm-rest and keyboard assembly.

Removing and installing components 41

Installing the I/O board

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image(s) indicate the location of the I/O board and provides a visual representation of the installation procedure.

Steps

1. Align the ports on the I/O board to the slots on the palm-rest and keyboard assembly.

2. Place the I/O board on the palm-rest and keyboard assembly.

3. Align the screw hole on the I/O board to the screw hole on the palm-rest and keyboard assembly.

4. Replace the screw (M2x3) that secures the I/O board to the palm-rest and keyboard assembly.

5. Close the left-display hinge and align the screw holes on the left-display hinge with the screw holes on the I/O board.

6. Replace the two screws (M2.5x4) that secure the left-display hinge to the I/O board.

7. Connect the I/O-board cable to the connector on the I/O board and close the latch.

8. Connect the power-button with fingerprint-reader cable to the connector on the I/O board and close the latch.

NOTE: This step is only applicable for computers shipped with the optional fingerprint reader.

9. Connect the coin-cell battery cable to the I/O board.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

42 Removing and installing components

Speakers

Removing the speakers

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Remove the base cover.

3. Remove the 3-cell battery or the 4-cell battery, whichever applicable.

About this task

The following image(s) indicate the location of the speakers and provides a visual representation of the removal procedure.

Steps

1. Peel off the tapes that secure the I/O-board cable and antenna cables to the palm-rest and keyboard assembly.

Removing and installing components 43

2. Lif the I/O-board cable and antenna cables and move them out of the way.

3. Lift the latch and disconnect the touchpad cable from the system board.

4. Lift the latch and disconnect the keyboard cable from the system board.

5. Lift the latch and disconnect the keyboard-backlight cable from the system board.

6. Disconnect the speaker cable from the system board.

7. Peel off the tape that secures the speaker cable to the palm-rest and keyboard assembly.

8. Remove the speaker cables from the routing guides on the palm-rest and keyboard assembly.

9. Lift the speakers along with their cables off the palm-rest and keyboard assembly.

Installing the speakers

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image(s) indicate the location of the speakers and provides a visual representation of the installation procedure.

44 Removing and installing components

Steps

1. Using the alignment posts, place the left and right speakers on the palm-rest and keyboard assembly.

NOTE: Ensure that the alignment posts are threaded through the rubber grommets on the speaker.

2. Route the speaker cable through the routing guides on the palm-rest and keyboard assembly.

3. Connect the speaker cable to the connector on the system board.

4. Adhere the tape that secures the speaker cable to the palm-rest and keyboard assembly.

5. Connect the touchpad cable to the system board and close the latch.

6. Connect the keyboard cable to the system board and close the latch.

7. Connect the keyboard-backlight cable to the system board and close the latch.

8. Place the I/O-board and antenna cables back into place and adhere the tapes that secure them to the palm-rest and

keyboard assembly.

Next steps

1. Install the 3-cell battery or the 4-cell battery, whichever applicable.

2. Install the base cover.

3. Follow the procedure in After working inside your computer.

Touchpad

Removing the touchpad

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Remove the base cover.

3. Remove the 3-cell battery or the 4-cell battery, whichever applicable.

About this task

The following image(s) indicate the location of the touchpad and provides a visual representation of the removal procedure.

Removing and installing components 45

Steps

1. Open the latch and disconnect the touchpad cable from the touchpad.

2. Remove the three screws (M1.6x2) that secure the touchpad bracket to the palm-rest and keyboard assembly.

3. Lift the touchpad bracket off the palm-rest and keyboard assembly.

4. Remove the two screws (M2x1.8) that secure the touchpad to the palm-rest and keyboard assembly.

5. Peel the tapes that secure the touchpad to the palm-rest and keyboard assembly.

6. Lift the touchpad off the palm-rest and keyboard assembly.

Installing the touchpad

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image(s) indicate the location of the touchpad and provides a visual representation of the installation procedure.

Steps

1. Place the touchpad on the palm-rest and keyboard assembly.

2. Turn the computer over and open the display to ensure that the touchpad is equally aligned on all sides.

NOTE: The image below shows the proper touchpad alignment for your computer.

46 Removing and installing components

3. Close the display and place the computer in the position shown.

4. Replace the two screws (M2x1.8) that secure the touchpad to the palm-rest and keyboard assembly.

5. Place the touchpad bracket on the touchpad.

6. Align the screw holes on the touchpad bracket to the screw holes on the palm-rest and keyboard assembly.

7. Replace the three screws (M1.6x2) that secure the touchpad bracket to the palm-rest and keyboard assembly.

8. Adhere the tapes that secure the touchpad to the palm-rest and keyboard asssembly.

9. Connect the touchpad cable to the touchpad and close the latch.

Next steps

1. Install the 3-cell battery or the 4-cell battery, whichever applicable.

2. Install the base cover.

3. Follow the procedure in After working inside your computer.

Fan

Removing the fan

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

About this task

The following image(s) indicate the location of the fan and provides a visual representation of the removal procedure.

Removing and installing components 47

Steps

1. Disconnect the fan cable from the system board.

2. Remove the two screws (M2x3) that secure the fan to the palm-rest and keyboard assembly.

3. Lift the fan off the palm-rest and keyboard assembly.

Installing the fan

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image(s) indicate the location of the fan and provides a visual representation of the installation procedure.

Steps

1. Place the fan on the palm-rest and keyboard assembly.

2. Align the screw holes on the fan with the screw holes on the palm-rest and keyboard assembly.

3. Replace the two screws (M2x3) that secure the fan to the palm-rest and keyboard assembly.

4. Connect the fan cable to the system board.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

48 Removing and installing components

Heat sink

Removing the heat sink

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

About this task

CAUTION: The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool

before you touch it.

NOTE: For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils in your skin

can reduce the heat transfer capability of the thermal grease.

The following image(s) indicate the location of the heat sink and provides a visual representation of the removal procedure.

Steps

1. In reverse sequential order (7>6>5>4>3>2>1) loosen the seven captive screws that secure the heat sink to the system

board.

NOTE: The number of screws varies depending on the configuration ordered.

2. Lift the heat sink from the system board.

Removing and installing components 49

Installing the heat sink

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

NOTE: If either the system board or the heat sink is replaced, use the thermal grease provided in the kit to ensure that

thermal conductivity is achieved.

The following image(s) indicate the location of the heat sink and provides a visual representation of the installation procedure.

Steps

1. Place the heat-sink on the system board.

2. Align the screw holes on the heat sink to the screw holes on the system board.

3. In sequential order (1>2>3>4>5>6>7) tighten the seven captive screws that secure the heat sink to the system board.

NOTE: The number of screws varies depending on the configuration ordered.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

50 Removing and installing components

Power button with optional fingerprint reader

Removing the power-button with optional fingerprint reader

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

4. Remove the I/O board.

About this task

The following image(s) indicate the location of the power-button with optional fingerprint reader and provides a visual

representation of the removal procedure.

Steps

1. Remove the screw (M2x3) that secures the power-button with optional fingerprint reader off the palm-rest and keyboard

assembly.

2. Lift the power-button with optional fingerprint reader off the palm-rest and keyboard assembly.

Installing the power-button with optional fingerprint reader

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

Removing and installing components 51

About this task

The following image(s) indicate the location of the power-button with optional fingerprint reader and provides a visual

representation of the installation procedure.

Steps

1. Using the alignment posts, place the power-button with optional fingerprint reader into its slot on the palm-rest and

keyboard assembly.

2. Replace the screw (M2x3) that secures the power-button with optional fingerprint reader to the palm-rest and keyboard

assembly.

Next steps

1. Install the I/O board.

2. Install the base cover.

3. Exit Service Mode.

4. Follow the procedure in After working inside your computer.

System board

Removing the system board

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Remove the base cover.

3. Remove the 3-cell battery or the 4-cell battery, whichever applicable.

4. Remove the M.2 2230 solid-state drive.

5. Remove the M.2 2280 solid-state drive.

52 Removing and installing components

6. Remove the memory.

7. Remove the wireless card.

8. Remove the heat sink.

About this task

The following image indicates the connectors on your system board.

1. display cable

2. power-adapter port-cable

3. keyboard-backlight cable

4. keyboard cable

5. touchpad cable

6. speaker cable

7. I/O-board cable

8. fan cable

The following image(s) indicate the location of the system board and provides a visual representation of the removal procedure.

Removing and installing components 53

54 Removing and installing components

Steps

1. Remove the two screws (M2.5x4) that secure the right-display hinge to the system board.

2. Pry open the right-display hinge at an angle of 90 degrees.

3. Peel the tape that covers the power-adapter port cable-connector on the system board.

4. Disconnect the power-adapter port cable from the system board.

5. Peel the tape that secures the display-cable connector latch to the system board.

6. Lift the latch and disconnect the display-cable from the connector on the system board.

7. Disconnect the fan cable from the system board.

8. Lift the I/O-board cable-connector latch and disconnect the I/O-board cable from the system board.

9. Disconnect the speaker cable from the system board.

10. Lift the latch and disconnect the touchpad cable from the system board.

11. Lift the latch and disconnect the keyboard cable from the system board.

12. Lift the latch and disconnect the keyboard-backlight cable from the system board.

NOTE: This step is only applicable for computers installed with a backlit keyboard.

13. Remove the two screws (M2x4) that secure the Type-C port-bracket to the system board.

14. Lift the Type-C port-bracket off the system board.

15. Remove the two screws (M2x2) that secure the system board to the palm-rest and keyboard assembly.

16. Lift the system board from the palm-rest and keyboard assembly.

Installing the system board

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image indicates the connectors on your system board.

Removing and installing components 55

1. display cable

2. power-adapter port-cable

3. keyboard-backlight cable

4. keyboard cable

5. touchpad cable

6. speaker cable

7. I/O-board cable

8. fan cable

The following image(s) indicate the location of the system board and provides a visual representation of the installation

procedure.

56 Removing and installing components

Removing and installing components 57

Steps

1. Place the system board on the palm-rest and keyboard assembly.

2. Align the screw holes on the system board with the screw holes on the palm-rest and keyboard assembly.

3. Replace the two screws (M2x2) that secure the system board to the palm-rest and keyboard assembly.

4. Place the Type-C port-bracket on the system board.

5. Replace the two screws (M2x4) that secure the Type-C port-bracket to the system board.

6. Connect the keyboard-backlight cable to the connector on the system board and close the latch.

NOTE: This step is only applicable if you are installing a backlit keyboard on your computer.

7. Connect the keyboard cable to the connector on the system board and close the latch.

8. Connect the touchpad cable to the connector on the system board and close the latch.

9. Connect the speaker cable to the system board.

10. Connect the I/O-board cable to the connector on the system board and close the latch.

58 Removing and installing components

11. Connect the fan cable to the system board.

12. Connect the display cable to the connector on the system board and close the latch.

13. Adhere the tape that secures the display-cable connector latch to the system board.

14. Connect the power-adapter port cable to the system board,

15. Adhere the tape that covers the power-adapter cable-connector on the system board.

16. Close the right-display hinge and align the screw holes on the right-display hinge with the screw holes on the system board.

17. Replace the two screws (M2.5x4) that secure the right-display hinge to the system board.

Next steps

1. Install the heat sink.

2. Install the wireless card.

3. Install the memory.

4. Install the M.2 2280 solid-state drive.

5. Install the M.2 2230 solid-state drive.

6. Install the 3-cell battery or the 4-cell battery, whichever applicable.

7. Install the base cover.

8. Follow the procedure in After working inside your computer.

Palm-rest and keyboard assembly

Removing the palm-rest and keyboard assembly

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Remove the base cover.

3. Remove the 3-cell battery or the 4-cell battery, whichever applicable.

4. Remove the coin-cell battery.

5. Remove the M.2 2230 solid-state drive.

6. Remove the M.2 2280 solid-state drive.

7. Remove the wireless card.

8. Remove the power-adapter port.

9. Remove the I/O board.

10. Remove the speakers.

11. Remove the touchpad.

12. Remove the fan.

13. Remove the display assembly.

14. Remove the power-button with optional fingerprint reader.

15. Remove the system board.

NOTE: The system board can be removed with the heat sink and solid-state drives attached.

About this task

The following image(s) indicate the location of the palm-rest and keyboard assembly and provides a visual representation of the

removal procedure.

Removing and installing components 59

Steps

After performing the pre-requisites you are left with the palm-rest and keyboard assembly.

Installing the palm-rest and keyboard assembly

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image(s) indicate the location of the palm-rest and keyboard assembly and provides a visual representation of the

installation procedure.

60 Removing and installing components

Steps

Place the palm-rest and keyboard assembly on a flat and clean surface and perform the post-requisites to install the palm-rest

and keyboard assembly.

Next steps

1. Install the system board.

2. Install the power-button with optional fingerprint reader.

3. Install the display assembly.

4. Install the fan.

5. Install the touchpad.

6. Install the speakers.

7. Install the I/O board.

8. Install the power-adapter port.

9. Install the wireless card.

10. Install the M.2 2280 solid-state drive.

11. Install the M.2 2230 solid-state drive.

12. Install the coin-cell battery.

13. Install the 3-cell battery or the 4-cell battery, whichever applicable.

14. Install the base cover.

15. Follow the procedure in After working inside your computer.

Removing and installing components 61

Drivers and downloads

When troubleshooting, downloading or installing drivers it is recommended that you read the Dell Knowledge Based article,

Drivers and Downloads FAQ SLN128938.

62 Drivers and downloads

System setup

CAUTION: Unless you are an expert computer user, do not change the settings in the BIOS Setup program.

Certain changes can make your computer work incorrectly.

NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not be displayed.

NOTE: Before you change BIOS Setup program, it is recommended that you write down the BIOS Setup program screen

information for future reference.

Use the BIOS Setup program for the following purposes:

●Get information about the hardware installed in your computer, such as the amount of RAM and the size of the hard drive.

●Change the system configuration information.

●Set or change a user-selectable option, such as the user password, type of hard drive installed, and enabling or disabling

base devices.

Entering BIOS setup program

Steps

1. Turn on your computer.

2. Press F2 immediately to enter the BIOS setup program.

NOTE: If you wait too long and the operating system logo appears, continue to wait until you see the desktop. Then,

turn off your computer and try again.

Navigation keys

NOTE: For most of the System Setup options, changes that you make are recorded but do not take effect until you restart

the system.

Table 3. Navigation keys

Keys Navigation

Up arrow Moves to the previous field.

Down arrow Moves to the next field.

Enter Selects a value in the selected field (if applicable) or follow

the link in the field.

Spacebar Expands or collapses a drop-down list, if applicable.

Tab Moves to the next focus area.

NOTE: For the standard graphics browser only.

Esc Moves to the previous page until you view the main screen.

Pressing Esc in the main screen displays a message that

prompts you to save any unsaved changes and restarts the

system.

System setup 63

Boot Sequence

Boot Sequence allows you to bypass the System Setup–defined boot device order and boot directly to a specific device (for

example: optical drive or hard drive). During the Power-on Self Test (POST), when the Dell logo appears, you can:

●Access System Setup by pressing F2 key

●Bring up the one-time boot menu by pressing F12 key

The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot menu options

are:

●Removable Drive (if available)

●STXXXX Drive (if available)

NOTE: XXX denotes the SATA drive number.

●Optical Drive (if available)

●SATA Hard Drive (if available)

●Diagnostics

The boot sequence screen also displays the option to access the System Setup screen.

System setup options

NOTE: Depending on this computer and its installed devices, the items that are listed in this section may or may not be

displayed.

Table 4. System setup options—System information menu

Overview

BIOS Version Displays the BIOS version number.

Service Tag Displays the Service Tag of the computer.

Asset Tag Displays the Asset Tag of the computer.

Manufacture Date Displays the manufacture date of the computer.

Ownership Date Displays the ownership date of the computer.

Express Service Code Displays the express service code of the computer.

Ownership Tag Displays the ownership tag of the computer.

Signed Firmware Update Displays whether the signed firmware update is enabled.

Default: Enabled

Battery Displays the battery health information.

Primary Displays the primary battery.

Battery Level Displays the battery level.

Battery State Displays the battery state.

Health Displays the battery health.

AC Adapter Displays whether an AC adapter is connected. If connected, the AC adapter

type.

PROCESSOR

Processor Type Displays the processor type.

Maximum Clock Speed Displays the maximum processor clock speed.

Minimum Clock Speed Displays the minimum processor clock speed.

Current Clock Speed Displays the current processor clock speed.

Core Count Displays the number of cores on the processor.

64 System setup

Table 4. System setup options—System information menu

Overview

Processor ID Displays the processor identification code.

Processor L2 Cache Displays the processor L2 Cache size.

Processor L3 Cache Displays the processor L3 Cache size.

Microcode Version Displays the microcode version.

Intel Hyper-Threading Capable Displays whether the processor is Hyper-Threading (HT) capable.

64-Bit Technology Displays whether 64-bit technology is used.

MEMORY

Memory Installed Displays the total computer memory installed.

Memory Available Displays the total computer memory available.

Memory Speed Displays the memory speed.

Memory Channel Mode Displays single or dual channel mode.

Memory Technology Displays the technology that is used for the memory.

DIMM A Size Displays the memory configuration of DIMM A.

DIMM B Size Displays the memory configuration of DIMM B.

DEVICES

Panel Type Displays the Panel Type of the computer.

Video Controller Displays the integrate graphics information of the computer.

Video Memory Displays the video memory information of the computer.

Wi-Fi Device Displays the Wi-Fi device installed in the computer.

Native Resolution Displays the native resolution of the computer.

Video BIOS Version Displays the video BIOS version of the computer.

Audio Controller Displays the audio controller information of the computer.

Bluetooth Device Displays whether a Bluetooth device is installed in the computer.

LOM MAC Address Displays the MAC address of the LAN on Motherboard (LOM)

Table 5. System setup options—Boot Configuration menu

Boot Configuration

Boot Sequence

Boot Mode: UEFI only Displays the boot mode of this computer.

Boot Sequence Specifies the order that the BIOS searches the list of devices to find an

operating system to boot.

By default, ONBOARD NIC (IPV4) is selected

By default, ONBOARD NIC (IPV6) is selected

By default, UEFI Hard Drive is selected

Secure Boot

Enable Secure Boot Enables secure boot using only validated boot software.

Default: OFF

Secure Boot Mode Modifies the behavior of Secure Boot to allow evaluation or enforcement of

UEFI driver signatures. Deployed Mode should be selected for normal operation

of Secure Boot.

By default, Deployed Mode is selected.

System setup 65

Table 5. System setup options—Boot Configuration menu

Boot Configuration

Expert Key Management

Enable Custom Mode Allows the PK, KEK, db, and dbx security key databases to be modified.

Default: OFF

NOTE: If Custom Mode is not enabled, any changes made with respect to

the keys will not be saved.

Custom Mode Key Management Allows for selection of key database.

●Save to File will save the key to a user-selected file.

●Replace from File will replace the current key with a key from a user-

selected file.

●Append from File will add a key to the current database from a user-

selected file.

●Delete will delete the selected key.

●Reset All Keys will reset all four keys to their default settings.

By default, PK security key database is selected.

By default, Save to File is selected.

Table 6. System setup options—Integrated Devices menu

Integrated Devices

Date/Time

Date Sets the computer date in MM/DD/YYYY format. Changes to the date take

effect immediately.

Time Sets the computer time in HH/MM/SS 24-hour format. You can switch

between 12-hour and 24-hour clock. Changes to the time take effect

immediately.

Camera

Enable Camera Enables or disables the camera.

By default, Enable Camera is selected.

Audio Enables or disables all integrated audio controller.

Default: ON

Enable Microphone Enables or disables microphone.

By default, Enable Microphone is selected.

Enable Internal Speaker Enables or disables internal speaker.

By default, Enable Internal Speaker is selected.

USB Configuration Enables or disables booting from USB mass storage devices such as external

hard drive, optical drive, and USB drive.

By default, Enable USB Boot Support is selected.

Table 7. System setup options—Storage menu (continued)

Storage

SATA/NVMe Operation

SATA/NVMe Operation Configures operating mode of the integrated storage device controller.

Default: RAID On. Storage device is configured to support RAID functions.

When enabled, all NVMe and SATA devices will be mapped under VMD

66 System setup

Table 7. System setup options—Storage menu

Storage

controller. Windows RST (Intel Rapid Restore Technology) driver, or Linux

kernel VMD driver must be loaded in order to boot the OS.

Storage Interface

Port Enablement Enables or disables the onboard drives.

Default: ON

Drive Information Displays the information of various onboard drives.

Table 8. System setup options—Display menu

Display

Display Brightness

Brightness on battery power Sets the screen brightness when the computer is running on battery power.

Default: 50

Brightness on AC power Sets the screen brightness when the computer is running on AC power.

Default: 100

Table 9. System setup options—Passwords menu

Passwords

Admin Password Enables the user to set, change, or delete the administrator (admin) password.

The admin password enables several security features

System Password Enables the user to set, change, or delete the system password.

Internal HDD-1 Password Enables the user to set, change, or delete the Internal HDD-1 password.

Table 10. System setup options—Update,Recovery menu

Update,Recovery

SupportAssist OS Recovery Enables or disables the boot flow for SupportAssist OS Recovery tool, in the

event of certain system error.

Default: ON

BIOSConnect Enables or disables cloud Service OS recovery if the main OS fails to boot

within the number of failures equal or greater than the value specified by

Dell Auto OS Recovery Threshold, and local Service does not boot, or is not

installed.

Default: ON

Dell Auto OS Recovery Threshold Controls the automatic boot flow for SupportAssist System Resolution Console

and for Dell operating system Recovery tool.

Default: 2.

Table 11. System setup options—System Management menu

System Management

Service Tag Displays the Service Tag of the computer.

Asset Tag Creates a system Asset Tag that can be used by an IT administrator to

uniquely identify a particular system. Once set in BIOS, the Asset Tag cannot

be changed.

Table 12. System setup options—Pre-boot Behavior menu

System setup 67

Table 12. System setup options—Pre-boot Behavior menu

Pre-boot Behavior

Adapter warnings

Enable Adapter warnings Enables or disables the computer to display adapter warning messages when

adapters with too little power capacity are detected.

Default: ON

Warnings and Errors Selects an action on encountering a warning or error during boot.

Default: Prompt on Warnings and Errors. Stop, prompt, and wait for user input

when warnings or errors are detected.

NOTE: Errors deemed critical to the operation of the computer hardware

will always halt the computer.

Table 13. System setup options—System Logs menu

System Logs

BIOS Event Log

Clear Bios Event Log Select keep or clear BIOS events.

Default: Keep

Thermal Event Log

Clear Thermal Event Log Select keep or clear Thermal events.

Default: Keep

Power Event Log

Clear POWER Event Log Select keep or clear Power events.

Default: Keep

Updating the BIOS in Windows

Prerequisites

It is recommended to update your BIOS (System Setup), when you replace the system board or if an update is available.

About this task

NOTE: If BitLocker is enabled, it must be suspended before updating the system BIOS, and then re-enabled after the BIOS

update is completed.

Steps

1. Restart the computer.

2. Go to www.dell.com/support.

●Enter the Service Tag or Express Service Code and click Search.

●Click Drivers & Downloads.

●Click Detect Drivers and follow the on-screen instructions.

3. If you are unable to detect or find the Service Tag, click Browse all products.

4. Choose the appropriate category to reach the product page.

5. Select your computer model, followed by its model number.

NOTE: The Product Support page of your computer appears.

6. Click Drivers & Downloads.

NOTE: The Drivers & Downloads section is displayed.

68 System setup

7. Click Category, and select BIOS from the drop-down list.

8. Click the toggle button Show downloads for only THIS PC XXXXXXX.

NOTE: XXXXXXX denotes the Service Tag.

9. Select the latest BIOS file and click Download.

10. After the download is complete, browse to the folder where you saved the system BIOS executable file.

11. Double-click the system BIOS executable file.

NOTE: Follow the on-screen instructions.

Updating BIOS on systems with BitLocker enabled

CAUTION: If BitLocker is not suspended before updating the BIOS, the next time you reboot the system it

will not recognize the BitLocker key. You will then be prompted to enter the recovery key to progress and the

system will ask for this on each reboot. If the recovery key is not known this can result in data loss or an

unnecessary operating system re-install. For more information on this subject, see Knowledge Article: https://

www.dell.com/support/article/sln153694

Updating your system BIOS using a USB flash drive

About this task

If the computer cannot load into Windows but there is still a need to update the BIOS, download the BIOS file using another

computer and save it to a bootable USB flash drive.

NOTE: You must use a bootable USB flash drive. For more information, see the knowledge base article SLN143196.

Steps

1. Download the BIOS update .exe file to another computer.

2. Copy the .exe file onto the bootable USB flash drive.

3. Insert the USB flash drive into the computer that requires the BIOS update.

4. Restart the computer and press F12 when the Dell logo appears to display the One Time Boot Menu.

5. Using arrow keys, select USB Storage Device and press Enter.

6. The computer restarts to a Diag C:\> prompt.

7. Run the file by typing the complete filename and press Enter.

8. The BIOS Update Utility is displayed. Follow the on-screen instructions.

System setup 69

Figure 1. DOS BIOS Update Screen

Flashing the BIOS from the F12 One-Time boot menu

Updating your system BIOS using a BIOS update.exe file copied to a FAT32 USB key and booting from the F12 one time boot

menu.

About this task

BIOS Update

You can run the BIOS update file from Windows using a bootable USB key or you can also update the BIOS from the F12

One-Time boot menu on the system.

Most Dell systems built after 2012 have this capability and you can confirm by booting your system to the F12 One-Time Boot

Menu to see if BIOS FLASH UPDATE is listed as a boot option for your system. If the option is listed, then the BIOS supports

this BIOS update option.

NOTE: Only systems with BIOS Flash Update option in the F12 One-Time Boot Menu can use this function.

Updating from the One-Time Boot Menu

To update your BIOS from the F12 One-Time boot menu, you will need:

●USB key formatted to the FAT32 file system (key does not have to be bootable)

●BIOS executable file that you downloaded from the Dell Support website and copied to the root of the USB key

●AC power adapter connected to the system

●Functional system battery to flash the BIOS

Perform the following steps to execute the BIOS update flash process from the F12 menu:

CAUTION: Do not power off the system during the BIOS update process. Powering off the system could make

the system fail to boot.

Steps

1. From a power off state, insert the USB key where you copied the flash into a USB port of the system .

2. Power on the system and press the F12 key to access the One-Time Boot Menu, Highlight BIOS Update using the mouse or

arrow keys then press Enter.

70 System setup

3. The flash BIOS menu will open, and then click the Flash from file.

4. Select external USB device.

System setup 71

5. Once the file is selected, Double click the flash target file, then press submit.

6. Click the Update BIOS then system will reboot to flash the BIOS.

72 System setup

7. Once complete, the system will reboot and the BIOS update process is completed.

System and setup password

Table 14. System and setup password

Password type Description

System password Password that you must enter to log on to your system.

Setup password Password that you must enter to access and make changes to

the BIOS settings of your computer.

You can create a system password and a setup password to secure your computer.

CAUTION: The password features provide a basic level of security for the data on your computer.

CAUTION: Anyone can access the data stored on your computer if it is not locked and left unattended.

NOTE: System and setup password feature is disabled.

Assigning a system setup password

Prerequisites

You can assign a new System or Admin Password only when the status is in Not Set.

About this task

To enter the system setup, press F2 immediately after a power-on or reboot.

Steps

1. In the System BIOS or System Setup screen, select Security and press Enter.

The Security screen is displayed.

System setup 73

2. Select System/Admin Password and create a password in the Enter the new password field.

Use the following guidelines to assign the system password:

●A password can have up to 32 characters.

●The password can contain the numbers 0 through 9.

●Only lower case letters are valid, upper case letters are not allowed.

●Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

3. Type the system password that you entered earlier in the Confirm new password field and click OK.

4. Press Esc and a message prompts you to save the changes.

5. Press Y to save the changes.

The computer reboots.

Deleting or changing an existing system setup password

Prerequisites

Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing

System and Setup password. You cannot delete or change an existing System or Setup password, if the Password Status is

Locked.

About this task

To enter the System Setup, press F2 immediately after a power-on or reboot.

Steps

1. In the System BIOS or System Setup screen, select System Security and press Enter.

The System Security screen is displayed.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password, alter or delete the existing system password and press Enter or Tab.

4. Select Setup Password, alter or delete the existing setup password and press Enter or Tab.

NOTE: If you change the System and/or Setup password, re enter the new password when prompted. If you delete the

System and Setup password, confirm the deletion when prompted.

5. Press Esc and a message prompts you to save the changes.

6. Press Y to save the changes and exit from System Setup.

The computer restarts.

Clearing CMOS settings

About this task

CAUTION: Clearing CMOS settings will reset the BIOS settings on your computer.

Steps

1. Enter Service Mode.

2. Remove the base cover.

3. Remove the coin-cell battery.

4. Wait for one minute.

5. Replace the coin-cell battery.

6. Replace the base cover.

7. Exit Service Mode.

74 System setup

Clearing BIOS (System Setup) and System passwords

About this task

To clear the system or BIOS passwords, contact Dell technical support as described at www.dell.com/contactdell.

NOTE: For information on how to reset Windows or application passwords, refer to the documentation accompanying

Windows or your application.

System setup 75

Troubleshooting

Locate the Service Tag or Express Service Code of

your Dell computer

Your Dell computer is uniquely identified by a Service Tag or Express Service Code. To view relevant support resources for your

Dell computer, we recommend entering the Service Tag or Express Service Code at www.dell.com/support.

For more information on how to find the Service Tag for your computer, see Locate the Service Tag for your Dell Laptop.

System-diagnostic lights

The power and battery status light indicates the power and battery status of the computer. These are the power states:

Solid white: Power adapter is connected, and the battery has more than 5% charge.

Amber: Computer is running on battery, and the battery has less than 5% charge.

Off:

●Power adapter is connected, and the battery is fully charged.

●Computer is running on battery, and the battery has more than 5% charge.

●Computer is in sleep state, hibernation, or turned off.

The power and battery-status light may also blink amber or white according to predefined "beep codes" indicating various

failures.

For example, the power and battery-status light blinks amber two times followed by a pause, and then blinks white three times

followed by a pause. This 2,3 pattern continues until the computer is turned off, indicating no memory or RAM is detected.

The following table shows different power and battery-status light patterns and associated problems.

NOTE: The following diagnostic light codes and recommended solutions are intended for Dell service technicians to

troubleshoot problems. You should only perform troubleshooting and repairs as authorized or directed by the Dell technical

support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty.

Table 15. Diagnostic-light codes

Diagnostic light codes

(Amber, white)

Problem description

1,1 TPM detection failure

1,2 Unrecoverable SPI flash failure

1,3 Short in hinge cable tripped OCP1

1,4 Short in hinge cable tripped OCP2

1,5 EC unable to program i-Fuse

1,6 EC internal Failure

2,1 Processor failure

2,2 System board: BIOS or ROM (Read-Only

Memory) failure

2,3 No memory or RAM (Random-Access Memory)

detected

76 Troubleshooting

Table 15. Diagnostic-light codes

Diagnostic light codes

(Amber, white)

Problem description

2,4 Memory or RAM (Random-Access Memory)

failure

2,5 Invalid memory installed

2,6 System-board or chipset error

2,7 Display failure - SBIOS message

2,8 Display failure - EC detection of power rail

failure

3,1 CMOS battery failure

3,2 PCI, video card/chip failure

3,3 BIOS recovery image not found

3,4 Recovery image found but invalid

3,5 Power-rail failure

3,6 System BIOS Flash incomplete

3,7 Management Engine (ME) error

Camera status light: Indicates whether the camera is in use.

●Solid white—Camera is in use.

●Off—Camera is not in use.

Caps Lock status light: Indicates whether Caps Lock is enabled or disabled.

●Solid white—Caps Lock enabled.

●Off—Caps Lock disabled.

SupportAssist | On-board Diagnostics

About this task

The SupportAssist | On-board Diagnostics performs a complete check of your hardware.

This diagnostic is the new on-board diagnostic tool and replaces the ePSA 3.0 diagnostics. It has a clean and modern user

interface, quicker tests, simplified messaging.

SupportAssist | On-board Diagnostics can be initiated by one of the following methods:

●Pressing F12 to enter one-time Boot Menu and selecting Diagnostics to initiate the diagnostics OR Fn + Power

●BIOS POST detecting a hardware failure or error and initiating the diagnostics

The SupportAssist | On-board Diagnostics is embedded with the BIOS and is launched by the BIOS internally. The embedded

system diagnostics provides a set of options for particular devices or device groups allowing you to:

●Run tests in either Quick Test Mode or Advanced Test Mode

●Run thorough tests to introduce additional test options to provide extra information about the failed device(s)

●Run tests in either Automatic Mode or Interactive Test Mode

●Run interactive tests on LCD panel and keyboard

●Display or save test results

●View status messages that indicate if the tests are completed successfully

●View error messages that indicate if problems were encountered during the test

NOTE: Some tests for specific devices require user interaction. Ensure that you are present at the computer terminal when

the diagnostic tests are performed.

For more information, see SupportAssist Pre-Boot System Performance Check.

Troubleshooting 77

Recovering the operating system

When your computer is unable to boot to the operating system even after repeated attempts, it automatically starts Dell

SupportAssist OS Recovery.

Dell SupportAssist OS Recovery is a standalone tool that is preinstalled in all Dell computers installed with Windows 10 operating

system. It consists of tools to diagnose and troubleshoot issues that may occur before your computer boots to the operating

system. It enables you to diagnose hardware issues, repair your computer, back up your files, or restore your computer to its

factory state.

You can also download it from the Dell Support website to troubleshoot and fix your computer when it fails to boot into their

primary operating system due to software or hardware failures.

For more information about the Dell SupportAssist OS Recovery, see Dell SupportAssist OS Recovery User's Guide at

www.dell.com/support.

Flashing BIOS (USB key)

Steps

1. Follow the procedure from step 1 to step 7 in "Flashing the BIOS" to download the latest BIOS setup program file.

2. Create a bootable USB drive. For more information see the knowledge base article SLN143196 at www.dell.com/support.

3. Copy the BIOS setup program file to the bootable USB drive.

4. Connect the bootable USB drive to the computer that needs the BIOS update.

5. Restart the computer and press F12 when the Dell logo is displayed on the screen.

6. Boot to the USB drive from the One Time Boot Menu.

7. Type the BIOS setup program filename and press Enter.

8. The BIOS Update Utility appears. Follow the instructions on the screen to complete the BIOS update.

Flashing the BIOS

About this task

You may need to flash (update) the BIOS when an update is available or when you replace the system board.

Follow these steps to flash the BIOS:

Steps

1. Turn on your computer.

2. Go to www.dell.com/support.

3. Click Product support, enter the Service Tag of your computer, and then click Submit.

NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.

4. Click Drivers & downloads > Find it myself.

5. Select the operating system installed on your computer.

6. Scroll down the page and expand BIOS.

7. Click Download to download the latest version of the BIOS for your computer.

8. After the download is complete, navigate to the folder where you saved the BIOS update file.

9. Double-click the BIOS update file icon and follow the instructions on the screen.

78 Troubleshooting

WiFi power cycle

About this task

If your computer is unable to access the internet due to WiFi connectivity issues a WiFi power cycle procedure may be

performed. The following procedure provides the instructions on how to conduct a WiFi power cycle:

NOTE: Some ISPs (Internet Service Providers) provide a modem/router combo device.

Steps

1. Turn off your computer.

2. Turn off the modem.

3. Turn off the wireless router.

4. Wait for 30 seconds.

5. Turn on the wireless router.

6. Turn on the modem.

7. Turn on your computer.

Troubleshooting 79

Getting help and contacting Dell

Self-help resources

You can get information and help on Dell products and services using these self-help resources:

Table 16. Self-help resources

Self-help resources Resource location

Information about Dell products and services www.dell.com

My Dell

Tips

Contact Support In Windows search, type Contact Support, and press

Enter.

Online help for operating system www.dell.com/support/windows

www.dell.com/support/linux

Troubleshooting information, user manuals, setup instructions,

product specifications, technical help blogs, drivers, software

updates, and so on.

www.dell.com/support

Dell knowledge base articles for a variety of computer

concerns.

1. Go to https://www.dell.com/support/home/?

app=knowledgebase.

2. Type the subject or keyword in the Search box.

3. Click Search to retrieve the related articles.

Learn and know the following information about your product:

●Product specifications

●Operating system

●Setting up and using your product

●Data backup

●Troubleshooting and diagnostics

●Factory and system restore

●BIOS information

See Me and My Dell at www.dell.com/support/manuals.

To locate the Me and My Dell relevant to your product,

identify your product through one of the following:

●Select Detect Product.

●Locate your product through the drop-down menu under

View Products.

●Enter the Service Tag number or Product ID in the

search bar.

Contacting Dell

To contact Dell for sales, technical support, or customer service issues, see www.dell.com/contactdell.

NOTE: Availability varies by country and product, and some services may not be available in your country.

NOTE: If you do not have an active internet connection, you can find contact information on your purchase invoice, packing

slip, bill, or Dell product catalog.

80 Getting help and contacting Dell

Table of Contents

DELL 5410 User Manual

Related Manuals