Table of Contents
- Vostro 14 5415 Service Manual
- Contents
- Working inside your computer
- Removing and installing components
- Recommended tools
- Screw list
- Major components of Vostro 14 5415
- Base cover
- Battery
- Memory module
- Solid-state drive
- Wireless card
- Fan
- Coin-cell battery
- Heat sink
- Network-port bracket
- I/O board
- Speakers
- Touchpad
- Display assembly
- Power button with optional fingerprint reader
- Power-adapter port
- System board
- Palm-rest and keyboard assembly
- Drivers and downloads
- System setup
- Troubleshooting
- Getting help and contacting Dell
DELL 5415 User Manual
Displayed below is the user manual for 5415 by DELL which is a product in the Notebooks category. This manual has pages.
Related Manuals
Vostro 14 5415
Service Manual
Regulatory Model: P143G
Regulatory Type: P143G002
August 2021
Rev. A01
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid
the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2020-2021 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Other trademarks may be trademarks of their respective owners.
Chapter 1: Working inside your computer...................................................................................... 6
Before working inside your computer.............................................................................................................................6
Safety instructions.............................................................................................................................................................. 6
Radiation Exposure Statement .................................................................................................................................. 7
Electrostatic discharge—ESD protection......................................................................................................................7
ESD field service kit ........................................................................................................................................................... 8
Transporting sensitive components................................................................................................................................ 9
After working inside your computer................................................................................................................................9
Chapter 2: Removing and installing components.......................................................................... 10
Recommended tools..........................................................................................................................................................10
Screw list............................................................................................................................................................................. 10
Major components of Vostro 14 5415............................................................................................................................ 11
Base cover........................................................................................................................................................................... 13
Removing the base cover...........................................................................................................................................13
Installing the base cover.............................................................................................................................................14
Battery.................................................................................................................................................................................. 16
Lithium-ion battery precautions............................................................................................................................... 16
Removing the 3-cell battery......................................................................................................................................16
Installing the 3-cell battery........................................................................................................................................ 17
Removing the 4-cell battery...................................................................................................................................... 18
Installing the 4-cell battery........................................................................................................................................ 19
Memory module................................................................................................................................................................. 20
Removing the memory............................................................................................................................................... 20
Installing the memory.................................................................................................................................................. 21
Solid-state drive................................................................................................................................................................ 23
Removing the M.2 2230 solid-state drive............................................................................................................. 23
Installing the M.2 2230 solid-state drive............................................................................................................... 23
Removing the M.2 2280 solid-state drive............................................................................................................. 24
Installing the M.2 2280 solid-state drive............................................................................................................... 25
Installing the solid-state drive mounting bracket................................................................................................ 26
Wireless card...................................................................................................................................................................... 28
Removing the wireless card...................................................................................................................................... 28
Installing the wireless card........................................................................................................................................ 29
Fan........................................................................................................................................................................................ 30
Removing the fan........................................................................................................................................................ 30
Installing the fan........................................................................................................................................................... 31
Coin-cell battery.................................................................................................................................................................31
Removing the coin-cell battery.................................................................................................................................31
Installing the coin-cell battery.................................................................................................................................. 32
Heat sink..............................................................................................................................................................................33
Removing the heat sink..............................................................................................................................................33
Installing the heat sink................................................................................................................................................34
Network-port bracket...................................................................................................................................................... 35
Contents
Contents 3
Removing the network-port bracket...................................................................................................................... 35
Installing the network-port bracket........................................................................................................................ 36
I/O board............................................................................................................................................................................. 37
Removing the I/O board............................................................................................................................................ 37
Installing the I/O board.............................................................................................................................................. 38
Speakers.............................................................................................................................................................................. 39
Removing the speakers..............................................................................................................................................39
Installing the speakers.................................................................................................................................................41
Touchpad.............................................................................................................................................................................42
Removing the touchpad.............................................................................................................................................42
Installing the touchpad............................................................................................................................................... 43
Display assembly................................................................................................................................................................44
Removing the display assembly............................................................................................................................... 44
Installing the display assembly..................................................................................................................................46
Power button with optional fingerprint reader.......................................................................................................... 48
Removing the power-button with optional fingerprint reader......................................................................... 48
Installing the power-button with optional fingerprint reader........................................................................... 49
Power-adapter port..........................................................................................................................................................50
Removing the power-adapter port......................................................................................................................... 50
Installing the power-adapter port........................................................................................................................... 50
System board...................................................................................................................................................................... 51
Removing the system board......................................................................................................................................51
Installing the system board....................................................................................................................................... 54
Palm-rest and keyboard assembly.................................................................................................................................57
Removing the palm-rest and keyboard assembly................................................................................................ 57
Installing the palm-rest and keyboard assembly.................................................................................................. 58
Chapter 3: Drivers and downloads............................................................................................... 60
Chapter 4: System setup............................................................................................................. 61
BIOS overview.................................................................................................................................................................... 61
Entering BIOS setup program......................................................................................................................................... 61
Navigation keys.................................................................................................................................................................. 61
Boot Sequence...................................................................................................................................................................62
System setup options.......................................................................................................................................................62
Updating the BIOS............................................................................................................................................................ 67
Flashing the BIOS........................................................................................................................................................ 67
Updating the BIOS in Linux and Ubuntu................................................................................................................ 67
Flashing BIOS (USB key)........................................................................................................................................... 67
Updating the BIOS from the F12 One-Time boot menu.....................................................................................68
System and admin password.......................................................................................................................................... 68
Assigning a system setup password....................................................................................................................... 69
Deleting or changing an existing system setup password.................................................................................69
Clearing BIOS (System Setup) and System passwords.......................................................................................... 69
Chapter 5: Troubleshooting......................................................................................................... 71
Handling swollen Lithium-ion batteries......................................................................................................................... 71
Dell SupportAssist Pre-boot System Performance Check diagnostics................................................................72
Running the SupportAssist Pre-Boot System Performance Check................................................................ 72
4Contents
System diagnostic lights.................................................................................................................................................. 72
Recovering the operating system..................................................................................................................................73
M-BIST................................................................................................................................................................................. 74
LCD Built-in Self Test (BIST)......................................................................................................................................... 74
WiFi power cycle................................................................................................................................................................74
Flea power release............................................................................................................................................................ 75
Chapter 6: Getting help and contacting Dell................................................................................ 76
Contacting Dell...................................................................................................................................................................77
Contents 5
Working inside your computer
Topics:
•Before working inside your computer
•Safety instructions
•Electrostatic discharge—ESD protection
•ESD field service kit
•Transporting sensitive components
•After working inside your computer
Before working inside your computer
About this task
NOTE: The images in this document may differ from your computer depending on the configuration you ordered.
Steps
1. Save and close all open files and exit all open applications.
2. Shut down your computer. Click Start > Power > Shut down.
NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down
instructions.
3. Disconnect your computer and all attached devices from their electrical outlets.
4. Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.
CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the
cable from the network device.
5. Remove any media card and optical disc from your computer, if applicable.
Safety instructions
Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless
otherwise noted, each procedure included in this document assumes that you have read the safety information that shipped
with your computer.
WARNING: Before working inside your computer, read the safety information that is shipped with your
computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
WARNING: Disconnect your computer from all power sources before opening the computer cover or panels.
After you finish working inside the computer, replace all covers, panels, and screws before connecting your
computer to an electrical outlet.
CAUTION: To avoid damaging the computer, ensure that the work surface is flat, dry, and clean.
CAUTION: To avoid damaging the components and cards, handle them by their edges, and avoid touching the
pins and the contacts.
1
6 Working inside your computer
CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical
assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the
safety instructions that is shipped with the product or at www.dell.com/regulatory_compliance.
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal
surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal
surface to dissipate static electricity which could harm internal components.
CAUTION: When you disconnect a cable, pull it by its connector or its pull tab, not the cable itself. Some cables
have connectors with locking tabs or thumbscrews that you must disengage before disconnecting the cable.
When disconnecting cables, keep them evenly aligned to avoid bending the connector pins. When connecting
cables, ensure that the ports and the connectors are correctly oriented and aligned.
CAUTION: Press and eject any installed card from the media-card reader.
NOTE: The color of your computer and certain components may appear differently than shown in this document.
Radiation Exposure Statement
This device meets the government's requirements for exposure to radio waves. This device is designed and manufactured not to
exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the
U.S. Government.
The exposure standard for wireless device employs a unit of measurement known as the Specific Absorption Rate, or SAR. The
SAR limit set by the FCC is 1,6 W/kg.
NOTE: Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting
at its highest certified power level in all tested frequency bands.
Electrostatic discharge—ESD protection
ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards,
processors, memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such
as intermittent problems or a shortened product life span. As the industry pushes for lower power requirements and increased
density, ESD protection is an increasing concern.
Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than
in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.
Two recognized types of ESD damage are catastrophic and intermittent failures.
●Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes
an immediate and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has
received a static shock and immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or
nonfunctional memory.
●Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of
intermittent failures means that most of the time when damage occurs, it is not immediately recognizable. The DIMM
receives a static shock, but the tracing is merely weakened and does not immediately produce outward symptoms related to
the damage. The weakened trace may take weeks or months to melt, and in the meantime may cause degradation of memory
integrity, intermittent memory errors, etc.
The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded")
failure.
Perform the following steps to prevent ESD damage:
●Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do not
provide adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts
with increased sensitivity to ESD damage.
●Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.
●When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static
packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you
discharge static electricity from your body.
Working inside your computer 7
●Before transporting a static-sensitive component, place it in an anti-static container or packaging.
ESD field service kit
The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components:
anti-static mat, wrist strap, and bonding wire.
Components of an ESD field service kit
The components of an ESD field service kit are:
●Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an
anti-static mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal
on the system being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly
on the mat. ESD-sensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.
●Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist
and bare metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that
is temporarily placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD
mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never
use wireless wrist straps. Always be aware that the internal wires of a wrist strap are prone to damage from normal wear
and tear, and must be checked regularly with a wrist strap tester in order to avoid accidental ESD hardware damage. It is
recommended to test the wrist strap and bonding wire at least once per week.
●ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored
kit, it is a best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A
wrist strap tester is the best method for doing this test. If you do not have your own wrist strap tester, check with your
regional office to find out if they have one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is
strapped to your wrist and push the button to test. A green LED is lit if the test is successful; a red LED is lit and an alarm
sounds if the test fails.
●Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts
that are insulators and often highly charged.
●Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For
example, deploying the kit for a server environment is different than for a desktop or portable environment. Servers are
typically installed in a rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always
look for a large open flat work area that is free of clutter and large enough to deploy the ESD kit with additional space to
accommodate the type of system that is being repaired. The workspace should also be free of insulators that can cause an
ESD event. On the work area, insulators such as Styrofoam and other plastics should always be moved at least 12 inches or
30 centimeters away from sensitive parts before physically handling any hardware components
●ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded
bags are preferred. However, you should always return the damaged part using the same ESD bag and packaging that the
new part arrived in. The ESD bag should be folded over and taped shut and all the same foam packing material should be
used in the original box that the new part arrived in. ESD-sensitive devices should be removed from packaging only at an
ESD-protected work surface, and parts should never be placed on top of the ESD bag because only the inside of the bag is
shielded. Always place parts in your hand, on the ESD mat, in the system, or inside an anti-static bag.
●Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts
to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.
ESD protection summary
It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static
mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all
insulator parts while performing service and that they use anti-static bags for transporting sensitive components.
8Working inside your computer
Transporting sensitive components
When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place
these parts in anti-static bags for safe transport.
Lifting equipment
Adhere to the following guidelines when lifting heavy weight equipment:
CAUTION: Do not lift greater than 50 pounds. Always obtain additional resources or use a mechanical lifting
device.
1. Get a firm balanced footing. Keep your feet apart for a stable base, and point your toes out.
2. Tighten stomach muscles. Abdominal muscles support your spine when you lift, offsetting the force of the load.
3. Lift with your legs, not your back.
4. Keep the load close. The closer it is to your spine, the less force it exerts on your back.
5. Keep your back upright, whether lifting or setting down the load. Do not add the weight of your body to the load. Avoid
twisting your body and back.
6. Follow the same techniques in reverse to set the load down.
After working inside your computer
About this task
CAUTION: Leaving stray or loose screws inside your computer may severely damage your computer.
Steps
1. Replace all screws and ensure that no stray screws remain inside your computer.
2. Connect any external devices, peripherals, or cables you removed before working on your computer.
3. Replace any media cards, discs, or any other parts that you removed before working on your computer.
4. Connect your computer and all attached devices to their electrical outlets.
5. Turn on your computer.
Working inside your computer 9
Removing and installing components
NOTE: The images in this document may differ from your computer depending on the configuration you ordered.
Topics:
•Recommended tools
•Screw list
•Major components of Vostro 14 5415
•Base cover
•Battery
•Memory module
•Solid-state drive
•Wireless card
•Fan
•Coin-cell battery
•Heat sink
•Network-port bracket
•I/O board
•Speakers
•Touchpad
•Display assembly
•Power button with optional fingerprint reader
•Power-adapter port
•System board
•Palm-rest and keyboard assembly
Recommended tools
The procedures in this document may require the following tools:
●Phillips screwdriver #0
●Phillips screwdriver #1
●Plastic scribe
Screw list
NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and
then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type is
restored when the component is replaced.
NOTE: Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surface when
replacing a component.
NOTE: Screw color may vary with the configuration ordered.
2
10 Removing and installing components
Table 1. Screw list
Component Screw type Quantity Screw image
Base cover ●Captive screws
(M2x7.5)
●M2x4
●2
●5
●
●
3-cell battery M2x3 3
4-cell battery M2x3 5
WLAN M2x3 1
Solid-state drive M2x3 1
Fan M2x3 2
Heat sink Captive screws 4
System board M2x2 2
Type-C bracket M2x4 2
Power button with fingerprint
reader
M2x3 1
Network port bracket M2x5 2
I/O board M2x3 1
Touchpad M1.6x2
M2x1.8
3
2
Power adapter M2.5x5 2
Display assembly M2.5x5 4
Major components of Vostro 14 5415
The following image shows the major components of Vostro 14 5415.
Removing and installing components 11
1. Base cover
2. Heat sink
3. System board
4. Memory
5. Battery
6. Right speaker
7. Palm-rest and keyboard assembly
8. Touchpad
9. Display assembly
10. Coin-cell battery
11. I/O board
12. M.2 2280 solid-state drive, if installed
13. Wireless card
14. M.2 2230 solid-state drive, if installed
15. Power-button with optional fingerprint-reader
12 Removing and installing components
16. Fan
17. Power-adapter port
NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These
parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative for
purchase options.
Base cover
Removing the base cover
Prerequisites
1. Follow the procedure in Before working inside your computer.
About this task
NOTE: Before removing the base cover, ensure that there is no micro-SD card installed in the micro-SD card slot on your
computer.
The following image(s) indicate the location of the base cover and provides a visual representation of the removal procedure.
Removing and installing components 13
Steps
1. Remove the five screws (M2x4) that secure the base cover to the palm-rest and keyboard assembly.
2. Loosen the two captive screws (M2x7.5) that secure the base cover to the palm-rest and keyboard assembly.
3. Using a plastic scribe, pry the base cover from the bottom left and continue to work on the sides to open the base cover.
4. Lift the base cover off the palm-rest and keyboard assembly.
Installing the base cover
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the base cover and provides a visual representation of the installation procedure.
14 Removing and installing components
Removing and installing components 15
Steps
1. Place and snap the base cover into place on the palm-rest and keyboard assembly.
2. Tighten the two captive screws (M2x7.5) that secure the base cover to the palm-rest and keyboard assembly.
3. Replace the five screws (M2x4) that secure the base cover to the palm-rest and keyboard assembly.
Next steps
1. Follow the procedure in After working inside your computer.
Battery
Lithium-ion battery precautions
CAUTION:
●Exercise caution when handling Lithium-ion batteries.
●Discharge the battery completely before removing it. Disconnect the AC power adapter from the system and
operate the computer solely on battery power—the battery is fully discharged when the computer no longer
turns on when the power button is pressed.
●Do not crush, drop, mutilate, or penetrate the battery with foreign objects.
●Do not expose the battery to high temperatures, or disassemble battery packs and cells.
●Do not apply pressure to the surface of the battery.
●Do not bend the battery.
●Do not use tools of any kind to pry on or against the battery.
●Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental
puncture or damage to the battery and other system components.
●If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing,
bending, or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical
support for assistance. See www.dell.com/contactdell.
●Always purchase genuine batteries from www.dell.com or authorized Dell partners and resellers.
●Swollen batteries should not be used and should be replaced and disposed properly. For guidelines on how to
handle and replace swollen Lithium-ion batteries, see Handling swollen Lithium-ion batteries.
Removing the 3-cell battery
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
About this task
The following image(s) indicate the location of the 3-cell battery and provides a visual representation of the removal procedure.
16 Removing and installing components
Steps
1. Peel the tape that secures the battery cable to the 3-cell battery.
2. Disconnect the battery cable from the system board.
3. Remove the three screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.
4. Lift the battery off the palm-rest and keyboard assembly.
Installing the 3-cell battery
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the 3-cell battery and provides a visual representation of the installation
procedure.
Removing and installing components 17
Steps
1. Align the screw holes on the battery with the screw holes on the palm-rest and keyboard assembly.
2. Replace the three screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.
3. Connect the battery cable to the system board.
4. Adhere the tape that secures the battery cable to the 3-cell battery.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
Removing the 4-cell battery
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
About this task
The following image(s) indicate the location of the 4-cell battery and provides a visual representation of the removal procedure.
18 Removing and installing components
Steps
1. Peel the tape that secures the battery cable to the 4-cell battery.
2. Disconnect the battery cable from the system board, if applicable.
3. Remove the five screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.
4. Lift the battery off the palm-rest and keyboard assembly.
Installing the 4-cell battery
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the 4-cell battery and provides a visual representation of the installation
procedure.
Removing and installing components 19
Steps
1. Align the screw holes on the battery with the screw holes on the palm-rest and keyboard assembly.
2. Replace the five screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.
3. Connect the battery cable to the system board.
4. Adhere the tape that secures the battery cable to the 4-cell battery.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
Memory module
Removing the memory
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
About this task
The following image(s) indicate the location of the memory and provides a visual representation of the removal procedure.
20 Removing and installing components
Steps
1. Lift the Mylar to access the memory module.
2. Using your fingertips, carefully spread apart the securing-clips on each end of the memory-module slot until the memory
module pops-up.
3. Remove the memory module from the memory-module slot on the system board.
NOTE: Your computer may have up to two memory modules installed. Repeat steps 1 to 3 if there is a second memory
module installed.
Installing the memory
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the memory and provides a visual representation of the installation procedure.
Removing and installing components 21
Steps
1. Lift the Mylar to access the memory-module slot.
2. Align the notch on the memory module with the tab on the memory-module slot on the system board.
3. Slide the memory module into the memory-module slot on the system board.
4. Press down on the memory module till the securing clips click, locking the memory module in place.
NOTE: Repeat steps 1 to 4 for each memory module being installed into your computer.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
22 Removing and installing components
Solid-state drive
Removing the M.2 2230 solid-state drive
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
About this task
NOTE: This procedure applies only to computers shipped with an M.2 2230 solid-state drive installed.
NOTE: The M.2 card installed on your computer will depend on the configuration ordered. Supported card configurations on
the M.2 card slot:
●M.2 2230 solid-state drive
●M.2 2280 solid-state drive
The following image(s) indicate the location of the M.2 2230 solid-state drive and provides a visual representation of the
removal procedure.
Steps
1. Remove the screw (M2x3) that secures the M.2 2230 solid-state drive to the system board.
2. Slide and lift the M.2 2230 solid-state drive off the system board.
3. Slide and lift the M.2 2230 solid-state drive off the system board.
Installing the M.2 2230 solid-state drive
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
Removing and installing components 23
About this task
NOTE: This procedure applies if you are installing a M.2 2230 solid-state drive.
NOTE: The M.2 card installed on your computer will depend on the configuration ordered. Supported card configurations on
the M.2 card slot:
●M.2 2230 solid-state drive + M.2 2230 solid-state drive mounting bracket
●M.2 2280 solid-state drive
The following image(s) indicate the location of the M.2 2230 solid-state drive and provides a visual representation of the
installation procedure.
Steps
1. Align the notch on the M.2 2230 solid-state drive with the tab on the M.2 card slot on the system board.
2. Slide the M.2 2230 solid-state drive into the M.2 card slot on the system board.
3. Replace the screw (M2x3) that secures the M.2 2230 solid-state drive to the system board.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
Removing the M.2 2280 solid-state drive
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
About this task
NOTE: This procedure applies only to computers shipped with a M.2 2280 solid-state drive installed.
NOTE: The M.2 card installed on your computer will depend on the configuration ordered. Supported card configurations on
the M.2 card slot:
24 Removing and installing components
●M.2 2230 solid-state drive
●M.2 2280 solid-state drive
The following image(s) indicate the location of the M.2 2280 solid-state drive and provides a visual representation of the
removal procedure.
Steps
1. Remove the screw (M2x3) that secures the M.2 2280 solid-state drive to the palm-rest and keyboard assembly.
2. Slide and remove the M.2 2280 solid-state drive from the M.2 card slot on the system board.
Installing the M.2 2280 solid-state drive
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
NOTE: This procedure applies if you are installing a M.2 2280 solid-state drive.
NOTE: The M.2 card installed on your computer will depend on the configuration ordered. Supported card configurations on
the M.2 card slot:
●M.2 2230 solid-state drive
●M.2 2280 solid-state drive
The following image(s) indicate the location of the M.2 2280 solid-state drive and provides a visual representation of the
installation procedure.
Removing and installing components 25
Steps
1. Align the notch on the M.2 2280 solid-state drive with the tab on the M.2 card slot on the system board.
2. Slide the M.2 2280 solid-state drive into the M.2 card slot on the system board.
3. Replace the screw (M2x3) that secures the M.2 2280 solid-state drive to the palm-rest and keyboard assembly.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
Installing the solid-state drive mounting bracket
About this task
The following image provides a visual representation of the procedure to install the solid-state drive mounting bracket when
replacing a M.2 2230 solid-state drive with a M.2 2280 solid-state drive.
26 Removing and installing components
The following image provides a visual representation of the procedure to install the solid-state drive mounting bracket when
replacing a M.2 2280 solid-state drive with a M.2 2230 solid-state drive.
Steps
1. Remove the 2230 solid-state drive or 2280 solid-state drive, whichever applicable.
2. Peel the Mylar that covers the solid-state drive mounting-bracket and mounting-bracket slot.
3. Slide and remove the solid-state drive mounting-bracket from the mounting-bracket slot on the palm-rest and keyboard
assembly.
4. Rotate the solid-state drive mounting-bracket.
5. Slide the solid-state mounting-bracket into the mounting-bracket slot on the palm-rest and keyboard assembly.
6. Adhere the Mylar that covers the solid-state drive mounting-bracket and mounting-bracket slot.
7. Install the 2230 solid-state drive or 2280 solid-state drive, whichever applicable.
Removing and installing components 27
Wireless card
Removing the wireless card
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
About this task
The following image(s) indicate the location of the wireless card and provides a visual representation of the removal procedure.
Steps
1. Remove the screw (M2x3) that secures the wireless-card bracket to the wireless card and system board.
2. Lift the wireless-card bracket off the wireless card.
3. Disconnect the antenna cables from the wireless card.
4. Slide and remove the wireless card from the M.2 card slot on the system board.
28 Removing and installing components
Installing the wireless card
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the wireless card and provides a visual representation of the installation
procedure.
Steps
1. Connect the antenna cables to the wireless card.
Table 2. Antenna-cable color scheme
Connectors on the
wireless card
Antenna-cable color Silkscreen marking
Main White MAIN △ (white triangle)
Auxiliary Black AUX ▲ (black triangle)
Removing and installing components 29
2. Place the wireless-card bracket on the wireless card.
3. Align the notch on the wireless card with the tab on the M.2 card slot on the system board.
4. Slide the wireless card into the M.2 card slot on the system board.
5. Replace the screw (M2x3) that secures the wireless card and wireless-card bracket to the system board.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
Fan
Removing the fan
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
About this task
The following image(s) indicate the location of the fan and provides a visual representation of the removal procedure.
Steps
1. Disconnect the fan cable from the system board.
2. Remove the two screws (M2x3) that secure the fan to the palm-rest and keyboard assembly.
3. Lift the fan off the palm-rest and keyboard assembly.
30 Removing and installing components
Installing the fan
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the fan and provides a visual representation of the installation procedure.
Steps
1. Place the fan on the palm-rest and keyboard assembly.
2. Align the screw holes on the fan with the screw holes on the palm-rest and keyboard assembly.
3. Replace the two screws (M2x3) that secure the fan to the palm-rest and keyboard assembly.
4. Connect the fan cable to the system board.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
Coin-cell battery
Removing the coin-cell battery
Prerequisites
1. Follow the procedure in Before working inside your computer.
Removing and installing components 31
2. Remove the base cover.
About this task
The following image(s) indicate the location of the coin-cell battery and provides a visual representation of the removal
procedure.
Steps
1. Disconnect the coin-cell battery from the I/O board.
2. Peel and lift the coin-cell battery from the palm-rest and keyboard assembly.
Installing the coin-cell battery
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the coin-cell battery and provides a visual representation of the installation
procedure.
32 Removing and installing components
Steps
1. Connect the coin-cell battery cable to the I/O board.
2. Adhere the coin-cell battery to the palm-rest and keyboard assembly.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
Heat sink
Removing the heat sink
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
About this task
CAUTION: The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool
before you touch it.
NOTE: For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils in your skin
can reduce the heat transfer capability of the thermal grease.
The following image(s) indicate the location of the heat sink and provides a visual representation of the removal procedure.
Removing and installing components 33
Steps
1. In reverse sequential order (7>6>5>4>3>2>1) loosen the seven captive screws that secure the heat sink to the system
board.
NOTE: The number of screws varies depending on the configuration ordered.
2. Lift the heat sink from the system board.
Installing the heat sink
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
NOTE: If either the system board or the heat sink is replaced, use the thermal grease provided in the kit to ensure that
thermal conductivity is achieved.
The following image(s) indicate the location of the heat sink and provides a visual representation of the installation procedure.
34 Removing and installing components
Steps
1. Place the heat-sink on the system board.
2. Align the screw holes on the heat sink to the screw holes on the system board.
3. In sequential order (1>2>3>4>5>6>7) tighten the seven captive screws that secure the heat sink to the system board.
NOTE: The number of screws varies depending on the configuration ordered.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
Network-port bracket
Removing the network-port bracket
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
About this task
The following image(s) indicate the location of the network-port bracket and provides a visual representation of the removal
procedure.
Removing and installing components 35
Steps
1. Remove the two screws (M2.5x5) that secure the left-display hinge to the I/O board.
2. Pry open the left-display hinge at an angle of 90 degrees.
3. Remove the two screws (M2x5) that secure the network-port bracket to the I/O board.
4. Lift the network-port bracket off the I/O board.
Installing the network-port bracket
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the network-port bracket and provides a visual representation of the installation
procedure.
36 Removing and installing components
Steps
1. Place the network-port bracket on the I/O board.
2. Align the screw holes on the network-port bracket to the screw holes on the I/O board.
3. Replace the two screws (M2x5) that secure the network-port bracket to the I/O board.
4. Close the left-display hinge and align the screw holes on the left-display hinge with the screw holes on the I/O board.
5. Replace the two screws (M2.5x5) that secure the left-display hinge to the palm-rest and keyboard assembly.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
I/O board
Removing the I/O board
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
3. Remove the network-port bracket.
About this task
The following image(s) indicate the location of the I/O board and provides a visual representation of the removal procedure.
Removing and installing components 37
Steps
1. Lift the I/O-board cable-connector latch and disconnect the I/O-board cable from the I/O board.
2. Lift the power-button with fingerprint-reader cable-connector latch and disconnect the power-button with fingerprint-
reader cable from the I/O board.
NOTE: This step is only applicable for computers shipped with the optional fingerprint reader.
3. Remove the screw (M2x3) that secures the I/O board to the palm-rest and keyboard assembly.
4. Disconnect the coin-cell battery cable from the I/O board.
5. Lift the I/O board off the palm-rest and keyboard assembly.
Installing the I/O board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the I/O board and provides a visual representation of the installation procedure.
38 Removing and installing components
Steps
1. Align the ports on the I/O board to the slots on the palm-rest and keyboard assembly.
2. Place the I/O board on the palm-rest and keyboard assembly.
3. Align the screw hole on the I/O board to the screw hole on the palm-rest and keyboard assembly.
4. Replace the screw (M2x3) that secures the I/O board to the palm-rest and keyboard assembly.
5. Connect the I/O-board cable to the connector on the I/O board and close the latch.
6. Connect the power-button with fingerprint-reader cable to the connector on the I/O board and close the latch.
NOTE: This step is only applicable for computers shipped with the optional fingerprint reader.
7. Connect the coin-cell battery cable to the I/O board.
Next steps
1. Install the network-port bracket.
2. Install the base cover.
3. Follow the procedure in After working inside your computer.
Speakers
Removing the speakers
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
3. Remove the 3-cell battery or the 4-cell battery, whichever applicable.
Removing and installing components 39
About this task
The following image(s) indicate the location of the speakers and provides a visual representation of the removal procedure.
Steps
1. Peel off the tapes that secure the I/O-board cable and antenna cables to the palm-rest and keyboard assembly.
2. Lif the I/O-board cable and antenna cables and move them out of the way.
3. Lift the latch and disconnect the touchpad cable from the system board.
4. Lift the latch and disconnect the keyboard cable from the system board.
5. Lift the latch and disconnect the keyboard-backlight cable from the system board.
6. Disconnect the speaker cable from the system board.
7. Peel off the tape that secures the speaker cable to the palm-rest and keyboard assembly.
8. Remove the speaker cables from the routing guides on the palm-rest and keyboard assembly.
9. Lift the speakers along with their cables off the palm-rest and keyboard assembly.
40 Removing and installing components
Installing the speakers
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the speakers and provides a visual representation of the installation procedure.
Steps
1. Using the alignment posts, place the left and right speakers on the palm-rest and keyboard assembly.
NOTE: Ensure that the alignment posts are threaded through the rubber grommets on the speaker.
2. Route the speaker cable through the routing guides on the palm-rest and keyboard assembly.
3. Connect the speaker cable to the connector on the system board.
4. Adhere the tape that secures the speaker cable to the palm-rest and keyboard assembly.
5. Connect the touchpad cable to the system board and close the latch.
6. Connect the keyboard cable to the system board and close the latch.
Removing and installing components 41
7. Connect the keyboard-backlight cable to the system board and close the latch.
8. Place the I/O-board and antenna cables back into place and adhere the tapes that secure them to the palm-rest and
keyboard assembly.
Next steps
1. Install the 3-cell battery or the 4-cell battery, whichever applicable.
2. Install the base cover.
3. Follow the procedure in After working inside your computer.
Touchpad
Removing the touchpad
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
3. Remove the 3-cell battery or the 4-cell battery, whichever applicable.
About this task
The following image(s) indicate the location of the touchpad and provides a visual representation of the removal procedure.
Steps
1. Open the latch and disconnect the touchpad cable from the touchpad.
2. Remove the three screws (M1.6x2) that secure the touchpad bracket to the palm-rest and keyboard assembly.
3. Lift the touchpad bracket off the palm-rest and keyboard assembly.
4. Remove the two screws (M2x1.8) that secure the touchpad to the palm-rest and keyboard assembly.
5. Peel the tapes that secure the touchpad to the palm-rest and keyboard assembly.
6. Lift the touchpad off the palm-rest and keyboard assembly.
42 Removing and installing components
Installing the touchpad
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the touchpad and provides a visual representation of the installation procedure.
Steps
1. Place the touchpad on the palm-rest and keyboard assembly.
2. Turn the computer over and open the display to ensure that the touchpad is equally aligned on all sides.
NOTE: The image below shows the proper touchpad alignment for your computer.
3. Close the display and place the computer in the position shown.
4. Replace the two screws (M2x1.8) that secure the touchpad to the palm-rest and keyboard assembly.
5. Place the touchpad bracket on the touchpad.
6. Align the screw holes on the touchpad bracket to the screw holes on the palm-rest and keyboard assembly.
7. Replace the three screws (M1.6x2) that secure the touchpad bracket to the palm-rest and keyboard assembly.
8. Adhere the tapes that secure the touchpad to the palm-rest and keyboard asssembly.
9. Connect the touchpad cable to the touchpad and close the latch.
Removing and installing components 43
Next steps
1. Install the 3-cell battery or the 4-cell battery, whichever applicable.
2. Install the base cover.
3. Follow the procedure in After working inside your computer.
Display assembly
Removing the display assembly
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
About this task
The following image(s) indicate the location of the display assembly and provides a visual representation of the removal
procedure.
44 Removing and installing components
Removing and installing components 45
Steps
1. Peel the tape that secures the display-cable connector latch to the system board.
2. Lift the latch and disconnect the display-cable from the connector on the system board.
3. Remove the two screws (M2.5x5) that secure the right-display hinge to the system board.
4. Pry open the right-display hinge at an angle of 90 degrees.
5. Remove the two screws (M2.5x5) that secure the left-display hinge to the I/O board.
6. Pry open the left-display hinge at an angle of 90 degrees.
7. Gently lift the palm-rest and keyboard assembly off the display assembly
CAUTION: To avoid damaging the display, do not slide the palm-rest and keyboard assembly over the display
assembly.
Installing the display assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the display assembly and provides a visual representation of the installation
procedure.
46 Removing and installing components
Steps
1. Place the display assembly on a clean and flat surface with the display panel facing up.
2. Gently place the palm-rest and keyboard assembly under the display hinges.
CAUTION: To avoid damaging the display, do not slide the palm-rest and keyboard assembly over the display
assembly.
3. Close the left-display hinge and align the screw holes on the left-display hinge with the screw holes on the I/O board.
4. Replace the two screws (M2.5x5) that secure the left-display hinge to the palm-rest and keyboard assembly.
5. Close the right-display hinge and align the screw holes on the right-display hinge with the screw holes on the system board.
6. Replace the two screws (M2.5x5) that secure the right-display hinge to the palm-rest and keyboard assembly.
7. Connect the display cable to the connector on the system board and close the latch.
8. Adhere the tape that secures the display-cable connector latch to the system board.
Removing and installing components 47
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
Power button with optional fingerprint reader
Removing the power-button with optional fingerprint reader
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
3. Remove the I/O board.
About this task
The following image(s) indicate the location of the power-button with optional fingerprint reader and provides a visual
representation of the removal procedure.
Steps
1. Remove the screw (M2x3) that secures the power-button with optional fingerprint reader off the palm-rest and keyboard
assembly.
2. Lift the power-button with optional fingerprint reader off the palm-rest and keyboard assembly.
48 Removing and installing components
Installing the power-button with optional fingerprint reader
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the power-button with optional fingerprint reader and provides a visual
representation of the installation procedure.
Steps
1. Using the alignment posts, place the power-button with optional fingerprint reader into its slot on the palm-rest and
keyboard assembly.
2. Replace the screw (M2x3) that secures the power-button with optional fingerprint reader to the palm-rest and keyboard
assembly.
Next steps
1. Install the I/O board.
2. Install the base cover.
3. Follow the procedure in After working inside your computer.
Removing and installing components 49
Power-adapter port
Removing the power-adapter port
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
About this task
The following image(s) indicate the location of the power-adapter port and provides a visual representation of the removal
procedure.
Steps
1. Remove the two screws (M2.5x5) that secures the right-display hinge to the system board.
2. Pry open the right-display hinge at an angle of 90 degrees.
3. Peel the tape that covers the power-adapter port connector on the system board.
4. Disconnect the power-adapter port from the system board.
5. Remove the power-adapter port cable from the routing guides on the palm-rest and keyboard assembly.
6. Remove the power-adapter port from the palm-rest and keyboard assembly.
Installing the power-adapter port
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the power-adapter port and provides a visual representation of the installation
procedure.
50 Removing and installing components
Steps
1. Connect the power-adapter port cable to the system board.
2. Adhere the tape that covers the power-adapter port connector on the system board.
3. Route the power-adapter port cable through the routing guides on the palm-rest and keyboard assembly.
4. Place the power-adapter port into the slot on the palm-rest and keyboard assembly.
5. Close the right-display hinge and align the screw holes on the right-display hinge with the screw holes on the system board.
6. Replace the two screws (M2.5x5) that secures the right-display hinge to the system board.
Next steps
1. Install the base cover.
2. Follow the procedure in After working inside your computer.
System board
Removing the system board
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
3. Remove the 3-cell battery or the 4-cell battery, whichever applicable.
4. Remove the M.2 2230 solid-state drive.
5. Remove the M.2 2280 solid-state drive.
6. Remove the memory.
7. Remove the wireless card.
8. Remove the heat sink.
About this task
The following image indicates the connectors on your system board.
Removing and installing components 51
1. display cable
2. power-adapter port-cable
3. keyboard-backlight cable
4. keyboard cable
5. touchpad cable
6. speaker cable
7. I/O-board cable
8. fan cable
The following image(s) indicate the location of the system board and provides a visual representation of the removal procedure.
52 Removing and installing components
Steps
1. Remove the two screws (M2.5x5) that secure the right-display hinge to the system board.
2. Pry open the right-display hinge at an angle of 90 degrees.
3. Peel the tape that covers the power-adapter port cable-connector on the system board.
4. Disconnect the power-adapter port cable from the system board.
5. Peel the tape that secures the display-cable connector latch to the system board.
Removing and installing components 53
6. Lift the latch and disconnect the display-cable from the connector on the system board.
7. Disconnect the fan cable from the system board.
8. Lift the I/O-board cable-connector latch and disconnect the I/O-board cable from the system board.
9. Disconnect the speaker cable from the system board.
10. Lift the latch and disconnect the touchpad cable from the system board.
11. Lift the latch and disconnect the keyboard cable from the system board.
12. Lift the latch and disconnect the keyboard-backlight cable from the system board.
NOTE: This step is only applicable for computers installed with a backlit keyboard.
13. Remove the two screws (M2x4) that secure the Type-C port-bracket to the system board.
14. Lift the Type-C port-bracket off the system board.
15. Remove the two screws (M2x2) that secure the system board to the palm-rest and keyboard assembly.
16. Lift the system board from the palm-rest and keyboard assembly.
Installing the system board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image indicates the connectors on your system board.
1. display cable
2. power-adapter port-cable
3. keyboard-backlight cable
4. keyboard cable
5. touchpad cable
6. speaker cable
7. I/O-board cable
8. fan cable
54 Removing and installing components
The following image(s) indicate the location of the system board and provides a visual representation of the installation
procedure.
Removing and installing components 55
Steps
1. Place the system board on the palm-rest and keyboard assembly.
2. Align the screw holes on the system board with the screw holes on the palm-rest and keyboard assembly.
3. Replace the two screws (M2x2) that secure the system board to the palm-rest and keyboard assembly.
4. Place the Type-C port-bracket on the system board.
5. Replace the two screws (M2x4) that secure the Type-C port-bracket to the system board.
6. Connect the keyboard-backlight cable to the connector on the system board and close the latch.
NOTE: This step is only applicable if you are installing a backlit keyboard on your computer.
7. Connect the keyboard cable to the connector on the system board and close the latch.
8. Connect the touchpad cable to the connector on the system board and close the latch.
9. Connect the speaker cable to the system board.
10. Connect the I/O-board cable to the connector on the system board and close the latch.
56 Removing and installing components
11. Connect the fan cable to the system board.
12. Connect the display cable to the connector on the system board and close the latch.
13. Adhere the tape that secures the display-cable connector latch to the system board.
14. Connect the power-adapter port cable to the system board,
15. Adhere the tape that covers the power-adapter cable-connector on the system board.
16. Close the right-display hinge and align the screw holes on the right-display hinge with the screw holes on the system board.
17. Replace the two screws (M2.5x5) that secure the right-display hinge to the system board.
Next steps
1. Install the heat sink.
2. Install the wireless card.
3. Install the memory.
4. Install the M.2 2280 solid-state drive.
5. Install the M.2 2230 solid-state drive.
6. Install the 3-cell battery or the 4-cell battery, whichever applicable.
7. Install the base cover.
8. Follow the procedure in After working inside your computer.
Palm-rest and keyboard assembly
Removing the palm-rest and keyboard assembly
Prerequisites
1. Follow the procedure in Before working inside your computer.
2. Remove the base cover.
3. Remove the 3-cell battery or the 4-cell battery, whichever applicable.
4. Remove the coin-cell battery.
5. Remove the M.2 2230 solid-state drive.
6. Remove the M.2 2280 solid-state drive.
7. Remove the wireless card.
8. Remove the power-adapter port.
9. Remove the I/O board.
10. Remove the speakers.
11. Remove the touchpad.
12. Remove the fan.
13. Remove the display assembly.
14. Remove the power-button with optional fingerprint reader.
15. Remove the system board.
NOTE: The system board can be removed with the heat sink and solid-state drives attached.
About this task
The following image(s) indicate the location of the palm-rest and keyboard assembly and provides a visual representation of the
removal procedure.
Removing and installing components 57
Steps
After performing the pre-requisites you are left with the palm-rest and keyboard assembly.
Installing the palm-rest and keyboard assembly
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the palm-rest and keyboard assembly and provides a visual representation of the
installation procedure.
58 Removing and installing components
Steps
Place the palm-rest and keyboard assembly on a flat and clean surface and perform the post-requisites to install the palm-rest
and keyboard assembly.
Next steps
1. Install the system board.
2. Install the power-button with optional fingerprint reader.
3. Install the display assembly.
4. Install the fan.
5. Install the touchpad.
6. Install the speakers.
7. Install the I/O board.
8. Install the power-adapter port.
9. Install the wireless card.
10. Install the M.2 2280 solid-state drive.
11. Install the M.2 2230 solid-state drive.
12. Install the coin-cell battery.
13. Install the 3-cell battery or the 4-cell battery, whichever applicable.
14. Install the base cover.
15. Follow the procedure in After working inside your computer.
Removing and installing components 59
System setup
CAUTION: Unless you are an expert computer user, do not change the settings in the BIOS Setup program.
Certain changes can make your computer work incorrectly.
NOTE: Before you change BIOS Setup program, it is recommended that you write down the BIOS Setup program screen
information for future reference.
Use the BIOS Setup program for the following purposes:
●Get information about the hardware installed in your computer, such as the amount of RAM and the size of the hard drive.
●Change the system configuration information.
●Set or change a user-selectable option, such as the user password, type of hard drive installed, and enabling or disabling
base devices.
Topics:
•BIOS overview
•Entering BIOS setup program
•Navigation keys
•Boot Sequence
•System setup options
•Updating the BIOS
•System and admin password
•Clearing BIOS (System Setup) and System passwords
BIOS overview
The BIOS manages data flow between the computer's operating system and attached devices such as hard disk, video adapter,
keyboard, mouse, and printer.
Entering BIOS setup program
About this task
Turn on (or restart) your computer and press F2 immediately.
Navigation keys
NOTE: For most of the System Setup options, changes that you make are recorded but do not take effect until you restart
the system.
Keys Navigation
Up arrow Moves to the previous field.
Down arrow Moves to the next field.
Enter Selects a value in the selected field (if applicable) or follow the link in the field.
Spacebar Expands or collapses a drop-down list, if applicable.
Tab Moves to the next focus area.
4
System setup 61
Keys Navigation
Esc Moves to the previous page until you view the main screen. Pressing Esc in the main screen displays a
message that prompts you to save any unsaved changes and restarts the system.
Boot Sequence
Boot sequence enables you to bypass the System Setup–defined boot device order and boot directly to a specific device (for
example: optical drive or hard drive). During the Power-on Self-Test (POST), when the Dell logo appears, you can:
●Access System Setup by pressing F2 key
●Bring up the one-time boot menu by pressing F12 key.
The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot menu options
are:
UEFI only:
●Windows Boot Manager
●UEFI RST KXG60ZNV512G NVMe KIOXIA 512 GB 40NA83SKJ81L
The boot sequence screen also displays the option to access the System Setup screen.
System setup options
NOTE: Depending on this computer and its installed devices, the items that are listed in this section may or may not be
displayed.
Table 3. System setup options—Main menu
Main
System Time Displays the current system time of the computer in HH/MM/SS format.
System Date Displays the ownership date of the computer in MM/DD/YYYY format.
BIOS Version Displays the BIOS version of the computer.
Product Name Displays the system model name of the computer.
Service Tag Displays the service tag of the computer.
Asset Tag Displays the asset tag of the computer.
CPU Type Displays the processor type.
CPU Speed Displays the maximum processor clock speed.
CPU ID Displays the processor identification code.
CPU Cache
L1 Cache Displays the processor L1 Cache size.
L2 Cache Displays the processor L2 Cache size.
L3 Cache Displays the processor L3 Cache size.
M.2 PCIe SSD Displays the PCIe SSD information connected to the M.2 slot.
AC Adapter Type Displays whether an AC adapter is installed.
System Memory Displays the total computer memory installed.
Memory Speed Displays the memory speed.
Keyboard Type Displays the type of the keyboard (option could be backlit or non-backlit).
62 System setup
Table 4. System setup options—Advance menu
Advance
Virtualization Specify whether a Virtual Machine Monitor (VMM) can utilize the additional
hardware capabilities provided by Onboard Virtualization Technology.
Options are:
●Enabled (Default)
●Disabled
Integrated NIC Allows pre-OS and early OS networking features to use any enabled NICs.
Options are:
●Enabled (Default)
●Disabled
USB Emulation Allows to enable USB emulation.
Options are:
●Enabled (Default)
●Disabled
SATA Operation Allows to select the SATA mode of the computer. Option is set to AHCI.
Adapter Warnings Displays Adapter Warning during the POST when Battery Level is Critically low.
Options are:
●Enabled (Default)
●Disabled
Function Key Behavior Allows to reverse Function Key Primary behavior with secondary.
Options are:
●Multimedia Key(Default)
●Function Key
Keyboard Illumination Allows to Switch-on/switch-off the Keyboard backlight.
Options are:
●Disable
●Dim
●Bright (Default)
Keyboard Backlight with AC Allows to permanently turn off/turn-on the Keyboard backlight without the AC
adapter.
Options are from 5 Seconds to 15 Minutes. Default option is set to1 Minute.
Keyboard Backlight with Battery Allows to permanently turn off/turn-on the Keyboard backlight without the AC
adapter.
Options are from 5 Seconds to 15 Minutes. Default option is set to1 Minute.
Battery Health Shows Battery Health and Charge Status.
External USB Ports Allows to turn off the External USB ports in the Operating System.
Options are:
●Enabled (Default)
●Disabled
Microphone Allows to Switch-on/switch-off the microphone.
Options are:
●Enabled (Default)
●Disabled
Camera Allows to Switch-on/switch-off the Camera.
System setup 63
Table 4. System setup options—Advance menu (continued)
Advance
Options are:
●Enabled (Default)
●Disabled
Internal Bluetooth Allows to Switch-on/switch-off the Bluetooth.
Options are:
●Enabled (Default)
●Disabled
Internal WLAN Allows to Switch-on/switch-off the Wireless Card.
Options are:
●Enabled (Default)
●Disabled
Media Card Reader Allows to enable/disable the Media Card reader.
Options are:
●Enabled (Default)
●Disabled
Fingerprint Reader Allows to enable/disable the Fingerprint reader.
Options are:
●Enabled (Default)
●Disabled
Boot Disable Disable the automatic Boot.
Options are:
●Enabled
●Disabled (Default)
Battery Charge Configuration Displays the Battery Charge configuration.
Options are:
●Adaptive (Default)
●Standard
●ExpressCharge(™)
●Primarily AC Use
●Custom
Advanced Battery Charge
Configutration
Displays the Advanced Charge configuration.
Options are:
●Enabled
●Disabled (Default)
Power on LID open Controls the Power function on LID open action.
Options are:
●Enabled (Default)
●Disabled
Maintenance Maintenance information.
Data Wipe on next boot Performs Data wipe on next boot. Options are:
●Disabled (Default)
●Enabled
BIOS Recovery from Hard Drive Performs reset of firmware to the factory image saved on the secondary
storage. Options are:
64 System setup
Table 4. System setup options—Advance menu (continued)
Advance
●Enabled (Default)
●Disabled
BIOS Auto Recovery Performs auto firmware reset when corrupted BIOS is detected. Options are:
●Disabled (Default)
●Enabled
SupportAssist System Resolution Onboard Diagnostics
Auto OS Recovery Threshold Performs SupportAssist OS recovery after the set value failed boot attempts.
Options are:
●Off
●1
●2 (Default)
●3
Support Assist OS Recovery Enabled Support Assist OS recovery on failed boot attempts. Options are:
●Disabled
●Enabled (Default)
Table 5. System setup options—Security menu
Security
Admin Password Displays the Status of the administrator password.
System Password Displays the Status of the computer password.
Asset Tag Displays and allows to edit the Asset Tag of the computer.
Admin Password Set, change, or delete the administrator password.
System Password Set, change, or delete the computer password.
Password Change Set the status to allow User to set the System Password. The options are:
●Permitted (Default)
●Disabled
Password Bypass Set the status to allow User to bypass System Password. The options are:
●Disable (Default)
●Reboot Bypass
Absolute® Set the Status of the Absolute Module on the computer. The options are:
●Activate
●Deactivate
Absolute® Status Displays the Status of the Absolute Module on the computer. The options are:
●Disabled
●Enabled (Default)
●Permanently Disabled
Firmware TPM Enable or disable TPM 2.0 security options.
TPM Security TPM 2.0 Security options.
TPM On Turn On/Off TPM security option. The options are:
●On
●Off
PPI Bypass for Enable Commands Controls the TPM Physical Presence Interface(PPI). When enabled, this
setting allows the OS to skip BIOS PPI user prompts when issuing TPM PPI
enable and activate commands. The Options are:
●Enabled
●Disabled (Default)
System setup 65
Table 5. System setup options—Security menu (continued)
Security
PPI Bypass for Disable Commands Controls the TPM Physical Presence Interface(PPI). When enabled, this
setting will allow the OS to skip BIOS PPI user prompts when issuing TPM
PPI disable and deactivate commands(#2, 4, 7, 9, & 11). The options are:
●Disabled (Default)
●Enabled
Attestation Enable Provides for the user to control whether the TPM Endorsement Hierarchy is
available to the OS. The options are:
●Disabled
●Enabled (Default)
Key Storage Enable Provides for the user to control whether TPM Storage Hierarchy is available to
the operating system. The options are:
●Disabled
●Enabled (Default)
SHA-256 Provides the BIOS and the TPM to use the SHA-256 hash algorithm to extend
measurements into the TPM PCRs during BIOS boot. The options are:
●Disabled
●Enabled (Default)
Clear Clears the TPM owner information, and returns the TPM to the default state.
The options are:
●Disabled (Default)
●Enabled
PPI Bypass for Clear Commands Controls the TPM Physical Presence Interface(PPI). When enabled, this
setting will allow the OS to skip BIOS PPI user prompts when issuing the Clear
command. The options are:
●Disabled (Default)
●Enabled
TPM Status Displays the Status of the TPM Module on the computer. The options are:
●Disabled
●Enabled (Default)
UEFI Firmware Capsule Updates Enable or disable BIOS updates through UEFI capsule update packages.
By default, the option is enabled.
Secure Boot Ensures the system boots using only to validated boot software.
Table 6. System setup options—Boot menu
Boot
File Broswer Add Boot Option
Windows Boot Manager: Displays the Default UEFI Boot Path of the computer Operating System and
allows to navigate and select the EFI file.
NOTE: Option may differ with the Linux Operating System.
File Browser Del Boot Option
Windows Boot Manager: Displays the Dell Boot Path of the Default Boot Option..
NOTE: Option may differ with the Linux Operating System.
UEFI BOOT
HDD1- Windows Boot Manager Displays the Device ID of the Secondary Storage of the computer.
UEFI Onboard LAN IPv4 Displays the Device ID of the UEFI enabled Onboard IPv4 LAN controller.
UEFI Onboard LAN IPv6 Displays the Device ID of the UEFI enabled Onboard IPv6 LAN controller.
66 System setup
Table 7. System setup options—Exit menu
Exit
Exit Saving Changes Exit the System Setup saving the changes made to the Setup Options.
Save Change Without Exit Save the Changes made to the System Setup and continue the Setup.
Exit Discarding Changes Exit the System Setup without saving the changes made to the Setup Options.
Load Optional Defaults Load the Factory Defaults in the System Setup Options.
Discard Changes Discard any changes made to the System Setup and continue the Setup.
Updating the BIOS
Flashing the BIOS
About this task
You may need to flash (update) the BIOS when an update is available or when you replace the system board.
Follow these steps to flash the BIOS:
Steps
1. Turn on your computer.
2. Go to www.dell.com/support.
3. Click Product support, enter the Service Tag of your computer, and then click Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.
4. Click Drivers & downloads > Find it myself.
5. Select the operating system installed on your computer.
6. Scroll down the page and expand BIOS.
7. Click Download to download the latest version of the BIOS for your computer.
8. After the download is complete, navigate to the folder where you saved the BIOS update file.
9. Double-click the BIOS update file icon and follow the instructions on the screen.
Updating the BIOS in Linux and Ubuntu
To update the system BIOS on a computer that is installed with Linux or Ubuntu, see the knowledge base article 000131486 at
www.dell.com/support.
Flashing BIOS (USB key)
Steps
1. Follow the procedure from step 1 to step 7 in "Flashing the BIOS" to download the latest BIOS setup program file.
2. Create a bootable USB drive. For more information see the knowledge base article SLN143196 at www.dell.com/support.
3. Copy the BIOS setup program file to the bootable USB drive.
4. Connect the bootable USB drive to the computer that needs the BIOS update.
5. Restart the computer and press F12 when the Dell logo is displayed on the screen.
6. Boot to the USB drive from the One Time Boot Menu.
7. Type the BIOS setup program filename and press Enter.
8. The BIOS Update Utility appears. Follow the instructions on the screen to complete the BIOS update.
System setup 67
Updating the BIOS from the F12 One-Time boot menu
Update your computer BIOS using the BIOS update.exe file that is copied to a FAT32 USB drive and booting from the F12
One-Time boot menu.
About this task
BIOS Update
You can run the BIOS update file from Windows using a bootable USB drive or you can also update the BIOS from the F12
One-Time boot menu on the computer.
Most of the Dell computers built after 2012 have this capability, and you can confirm by booting your computer to the F12
One-Time Boot Menu to see if BIOS FLASH UPDATE is listed as a boot option for your computer. If the option is listed, then the
BIOS supports this BIOS update option.
NOTE: Only computers with BIOS Flash Update option in the F12 One-Time boot menu can use this function.
Updating from the One-Time boot menu
To update your BIOS from the F12 One-Time boot menu, you need the following:
●USB drive formatted to the FAT32 file system (key does not have to be bootable)
●BIOS executable file that you downloaded from the Dell Support website and copied to the root of the USB drive
●AC power adapter that is connected to the computer
●Functional computer battery to flash the BIOS
Perform the following steps to perform the BIOS update flash process from the F12 menu:
CAUTION: Do not turn off the computer during the BIOS update process. The computer may not boot if you turn
off your computer.
Steps
1. From a turn off state, insert the USB drive where you copied the flash into a USB port of the computer.
2. Turn on the computer and press F12 to access the One-Time Boot Menu, select BIOS Update using the mouse or arrow keys
then press Enter.
The flash BIOS menu is displayed.
3. Click Flash from file.
4. Select external USB device.
5. Select the file and double-click the flash target file, and then click Submit.
6. Click Update BIOS. The computer restarts to flash the BIOS.
7. The computer will restart after the BIOS update is completed.
System and admin password
Table 8. System and admin password
Password type Description
System password Password that you must enter to log on to your system.
Admin password Password that you must enter to access and make changes to
the BIOS settings of your computer.
You can create a system password and a admin password to secure your computer.
CAUTION: The password features provide a basic level of security for the data on your computer.
CAUTION: Anyone can access the data stored on your computer if it is not locked and left unattended.
NOTE: System and admin password feature is disabled as factory default setting.
68 System setup
Assigning a system setup password
Prerequisites
You can assign a new System or Admin Password only when the status is in Not Set.
About this task
To enter the system setup, press F2 immediately after a power-on or reboot.
Steps
1. In the System BIOS or System Setup screen, select Security and press Enter.
The Security screen is displayed.
2. Select System/Admin Password and create a password in the Enter the new password field.
Use the following guidelines to assign the system password:
●A password can have up to 32 characters.
●The password can contain the numbers 0 through 9.
●Only lower case letters are valid, upper case letters are not allowed.
●Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).
3. Type the system password that you entered earlier in the Confirm new password field and click OK.
4. Press Esc and a message prompts you to save the changes.
5. Press Y to save the changes.
The computer reboots.
Deleting or changing an existing system setup password
Prerequisites
Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing
System and Setup password. You cannot delete or change an existing System or Setup password, if the Password Status is
Locked.
About this task
To enter the System Setup, press F2 immediately after a power-on or reboot.
Steps
1. In the System BIOS or System Setup screen, select System Security and press Enter.
The System Security screen is displayed.
2. In the System Security screen, verify that Password Status is Unlocked.
3. Select System Password, alter or delete the existing system password and press Enter or Tab.
4. Select Setup Password, alter or delete the existing setup password and press Enter or Tab.
NOTE: If you change the System and/or Setup password, re enter the new password when prompted. If you delete the
System and Setup password, confirm the deletion when prompted.
5. Press Esc and a message prompts you to save the changes.
6. Press Y to save the changes and exit from System Setup.
The computer restarts.
Clearing BIOS (System Setup) and System passwords
About this task
NOTE: To conduct a BIOS and System password reset, you must call the Dell Tech Support number in your region.
System setup 69
Steps
1. Key in your computer's service tag number into the locked BIOS/system setup screen.
2. Convey the code generated to the Dell Tech Support agent.
3. The Dell Tech Support agent will provide a 32 character Master System Password that can be used to access the locked
BIO/system setup.
70 System setup
Troubleshooting
Topics:
•Handling swollen Lithium-ion batteries
•Dell SupportAssist Pre-boot System Performance Check diagnostics
•System diagnostic lights
•Recovering the operating system
•M-BIST
•LCD Built-in Self Test (BIST)
•WiFi power cycle
•Flea power release
Handling swollen Lithium-ion batteries
Like most laptops, Dell laptops use lithium-ion batteries. One type of lithium-ion battery is the lithium-ion polymer battery.
Lithium-ion polymer batteries have increased in popularity in recent years and have become standard in the electronics industry
due to customer preferences for a slim form factor (especially with newer ultra-thin laptops) and long battery life. Inherent to
lithium-ion polymer battery technology is the potential for swelling of the battery cells.
Swollen battery may impact the performance of the laptop. To prevent possible further damage to the device enclosure or
internal components leading to malfunction, discontinue the use of the laptop and discharge it by disconnecting the AC adapter
and letting the battery drain.
Swollen batteries should not be used and should be replaced and disposed of properly. We recommend contacting Dell product
support for options to replace a swollen battery under the terms of the applicable warranty or service contract, including options
for replacement by a Dell authorized service technician.
The guidelines for handling and replacing Lithium-ion batteries are as follows:
●Exercise caution when handling Lithium-ion batteries.
●Discharge the battery before removing it from the system. To discharge the battery, unplug the AC adapter from the system
and operate the system only on battery power. When the system will no longer power on when the power button is pressed,
the battery is fully discharged.
●Do not crush, drop, mutilate, or penetrate the battery with foreign objects.
●Do not expose the battery to high temperatures, or disassemble battery packs and cells.
●Do not apply pressure to the surface of the battery.
●Do not bend the battery.
●Do not use tools of any type to pry on or against the battery.
●If a battery gets stuck in a device as a result of swelling, do not try to free it as puncturing, bending, or crushing a battery
can be dangerous.
●Do not attempt to reassemble a damaged or swollen battery into a laptop.
●Swollen batteries that are covered under warranty should be returned to Dell in an approved shipping container (provided
by Dell)—this is to comply with transportation regulations. Swollen batteries that are not covered under warranty should be
disposed of at an approved recycling center. Contact Dell product support at https://www.dell.com/support for assistance
and further instructions.
●Using a non-Dell or incompatible battery may increase the risk of fire or explosion. Replace the battery only with a
compatible battery purchased from Dell that is designed to work with your Dell computer. Do not use a battery from other
computers with your computer. Always purchase genuine batteries from https://www.dell.com or otherwise directly from
Dell.
Lithium-ion batteries can swell for various reasons such as age, number of charge cycles, or exposure to high heat. For more
information on how to improve the performance and lifespan of the laptop battery and to minimize the possibility of occurrence
of the issue, see Dell Laptop Battery - Frequently Asked Questions.
5
Troubleshooting 71
Dell SupportAssist Pre-boot System Performance
Check diagnostics
About this task
SupportAssist diagnostics (also known as system diagnostics) performs a complete check of your hardware. The Dell
SupportAssist Pre-boot System Performance Check diagnostics is embedded with the BIOS and is launched by the BIOS
internally. The embedded system diagnostics provides a set of options for particular devices or device groups allowing you to:
●Run tests automatically or in an interactive mode
●Repeat tests
●Display or save test results
●Run thorough tests to introduce additional test options to provide extra information about the failed device(s)
●View status messages that inform you if tests are completed successfully
●View error messages that inform you of problems encountered during testing
NOTE: Some tests for specific devices require user interaction. Always ensure that you are present at the computer
terminal when the diagnostic tests are performed.
For more information, see Resolve Hardware Issues With Built-in and Online Diagnostics (SupportAssist ePSA, ePSA or PSA
Error Codes) .
Running the SupportAssist Pre-Boot System Performance Check
Steps
1. Turn on your computer.
2. As the computer boots, press the F12 key as the Dell logo appears.
3. On the boot menu screen, select the Diagnostics option.
4. Click the arrow at the bottom left corner.
Diagnostics front page is displayed.
5. Click the arrow in the lower-right corner to go to the page listing.
The items detected are listed.
6. To run a diagnostic test on a specific device, press Esc and click Yes to stop the diagnostic test.
7. Select the device from the left pane and click Run Tests.
8. If there are any issues, error codes are displayed.
Note the error code and validation number and contact Dell.
System diagnostic lights
Battery-status light
Indicates the power and battery-charge status.
Solid white — Power adapter is connected and the battery has more than 5 percent charge.
Amber — Computer is running on battery and the battery has less than 5 percent charge.
Off — Discharging or other power states
●Power adapter is connected and the battery is fully charged.
●Computer is running on battery and the battery has more than 5 percent charge.
●Computer is in sleep state, hibernation, discharging, or turned off.
The power and battery-status light blinks amber along with beep codes indicating failures.
For example, the power and battery-status light blinks amber two times followed by a pause, and then blinks white three times
followed by a pause. This 2,3 pattern continues until the computer is turned off indicating no memory or RAM is detected.
The following table shows different power and battery-status light patterns and associated problems.
72 Troubleshooting
Blinking Pattern Problem description Suggested resolution
2 1 CPU failure Run the Intel CPU diagnostics
tools. If problem persists,
replace the system board.
2 2 System Board failure
(included BIOS corruption or
ROM error)
Flash latest BIOS version. If
problem persists, replace the
system board.
2 3 No Memory / RAM detected Confirm that the memory
module is installed properly. If
problem persists, replace the
memory module.
2 4 Memory / RAM failure Reset and swap memory
modules amongst the slots. If
problem persists, replace the
memory module.
2 5 Invalid memory installed Reset and swap memory
modules amongst the slots. If
problem persists, replace the
memory module.
2 6 System board / Chipset Error Replace the system board.
2 7 LCD failure (SBIOS message) Replace the LCD module.
2 8 LCD failure (EC detection of
power rail failure)
Replace the system board.
3 1 CMOS battery failure Reset the CMOS battery
connection. If problem
persists, replace the RTC
battery.
3 2 PCI or Video card/chip failure Replace the system board.
3 3 BIOS recovery image not
found
Flash latest BIOS version. If
problem persists, replace the
system board.
3 4 BIOS recovery image found
but invalid
Flash latest BIOS version. If
problem persists, replace the
system board.
3 5 Power rail failure Replace the system board.
3 6 Flash corruption detected by
SBIOS.
Replace the system board.
Camera status light: Indicates whether the camera is in use.
●Solid white — Camera is in use.
●Off — Camera is not in use.
Caps Lock status light: Indicates whether Caps Lock is enabled or disabled.
●Solid white — Caps Lock enabled.
●Off — Caps Lock disabled.
Recovering the operating system
When your computer is unable to boot to the operating system even after repeated attempts, it automatically starts Dell
SupportAssist OS Recovery.
Dell SupportAssist OS Recovery is a standalone tool that is preinstalled in all Dell computers installed with Windows operating
system. It consists of tools to diagnose and troubleshoot issues that may occur before your computer boots to the operating
Troubleshooting 73
system. It enables you to diagnose hardware issues, repair your computer, back up your files, or restore your computer to its
factory state.
You can also download it from the Dell Support website to troubleshoot and fix your computer when it fails to boot into their
primary operating system due to software or hardware failures.
For more information about the Dell SupportAssist OS Recovery, see Dell SupportAssist OS Recovery User's Guide at
www.dell.com/serviceabilitytools. Click SupportAssist and then, click SupportAssist OS Recovery.
M-BIST
M-BIST (Built In Self-Test) diagnostics tool, featuring improved accuracy in system board failures.
NOTE: M-BIST can be manually initiated before POST (Power On Self Test).
How to run M-BIST
NOTE: M-BIST must be initiated on the system from a power-off state either connected to AC power or with battery only.
1. Press and hold both the M key on the keyboard and the power button to initiate M-BIST.
2. With both the M key and the power button held down, the battery indicator LED may exhibit two states:
a. OFF: No fault detected with the system board
b. AMBER: Indicates a problem with the system board
LCD Built-in Self Test (BIST)
Dell laptops have a built-in diagnostic tool that helps you determine if the screen abnormality you are experiencing is an inherent
problem with the LCD (screen) of the Dell laptop or with the video card (GPU) and PC settings.
When you notice screen abnormalities like flickering, distortion, clarity issues, fuzzy or blurry image, horizontal or vertical lines,
color fade etc., it is always a good practice to isolate the LCD (screen) by running the Built-In Self Test (BIST).
How to invoke LCD BIST Test
1. Power off the Dell laptop.
2. Disconnect any peripherals that are connected to the laptop. Connect only the AC adapter (charger) to the laptop.
3. Ensure that the LCD (screen) is clean (no dust particles on the surface of the screen).
4. Press and hold D key and Power on the laptop to enter LCD built-in self test (BIST) mode. Continue to hold the D key, until
you see color bars on the LCD (screen).
5. The screen will display multiple color bars and change colors on the entire screen to red, green, and blue.
6. Carefully inspect the screen for abnormalities.
7. Press Esc key to exit.
NOTE: Dell SupportAssist Pre-boot diagnostics upon launch, initiates an LCD BIST first, expecting a user intervention
confirm functionality of the LCD.
WiFi power cycle
About this task
If your computer is unable to access the internet due to WiFi connectivity issues a WiFi power cycle procedure may be
performed. The following procedure provides the instructions on how to conduct a WiFi power cycle:
NOTE: Some ISPs (Internet Service Providers) provide a modem/router combo device.
74 Troubleshooting
Steps
1. Turn off your computer.
2. Turn off the modem.
3. Turn off the wireless router.
4. Wait for 30 seconds.
5. Turn on the wireless router.
6. Turn on the modem.
7. Turn on your computer.
Flea power release
About this task
Flea power is the residual static electricity that remains on the computer even after it has been powered off and the battery has
been removed. The following procedure provides the instructions on how to conduct flea power release:
Steps
1. Turn off your computer.
2. Disconnect the power adapter from your computer.
3. Press and hold the power button for 15 seconds to drain the flea power.
4. Connect the power adapter to your computer.
5. Turn on your computer.
Troubleshooting 75
Getting help and contacting Dell
Self-help resources
You can get information and help on Dell products and services using these self-help resources:
Table 9. Self-help resources
Self-help resources Resource location
Information about Dell products and services www.dell.com
My Dell
Tips
Contact Support In Windows search, type Contact Support, and press
Enter.
Online help for operating system www.dell.com/support/windows
www.dell.com/support/linux
Access top solutions, diagnostics, drivers and downloads, and
learn more about your computer through videos, manuals and
documents.
Your Dell computer is uniquely identified by a Service Tag or
Express Service Code. To view relevant support resources for
your Dell computer, enter the Service Tag or Express Service
Code at www.dell.com/support.
For more information on how to find the Service Tag for your
computer, see Locate the Service Tag on your computer.
Dell knowledge base articles for a variety of computer
concerns
1. Go to www.dell.com/support.
2. On the menu bar at the top of the Support page, select
Support > Knowledge Base.
3. In the Search field on the Knowledge Base page, type the
keyword, topic, or model number, and then click or tap the
search icon to view the related articles.
Contacting Dell
To contact Dell for sales, technical support, or customer service issues, see www.dell.com/contactdell.
NOTE: Availability varies by country/region and product, and some services may not be available in your country/region.
NOTE: If you do not have an active Internet connection, you can find contact information about your purchase invoice,
packing slip, bill, or Dell product catalog.
Topics:
•Contacting Dell
6
76 Getting help and contacting Dell
Contacting Dell
Prerequisites
NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing
slip, bill, or Dell product catalog.
About this task
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and
some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues:
Steps
1. Go to Dell.com/support.
2. Select your support category.
3. Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.
4. Select the appropriate service or support link based on your need.
Getting help and contacting Dell 77