DELL 5480 User Manual

Displayed below is the user manual for 5480 by DELL which is a product in the Notebooks category. This manual has pages.

Related Manuals

DELL 5480 Manual

Dell Vostro 5480

Owner's Manual

Regulatory Model: P41G

Regulatory Type: P41G002

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other

jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.

2014 - 12

Rev. A00

Contents

1 Working on Your Computer................................................................................5

Before Working Inside Your Computer................................................................................................ 5

Turning Off Your Computer..................................................................................................................6

After Working Inside Your Computer................................................................................................... 7

2 Removing and Installing Components............................................................. 8

Recommended Tools............................................................................................................................8

System Overview...................................................................................................................................8

Removing the Base Cover.....................................................................................................................9

Installing the Base Cover.....................................................................................................................12

Removing the Battery..........................................................................................................................12

Installing the Battery............................................................................................................................14

Removing the Hard Disk Drive............................................................................................................14

Installing the Hard Drive......................................................................................................................15

Removing the Coin-Cell Battery.........................................................................................................15

Installing the Coin-Cell Battery...........................................................................................................16

Removing the WLAN Card.................................................................................................................. 16

Installing the WLAN Card.................................................................................................................... 16

Removing the System Fan...................................................................................................................17

Installing the System Fan.................................................................................................................... 20

Removing the Heatsink.......................................................................................................................20

Installing the Heatsink......................................................................................................................... 21

Removing the Memory Module.......................................................................................................... 21

Installing the Memory......................................................................................................................... 22

Removing the System Board.............................................................................................................. 22

Installing the System Board................................................................................................................ 24

Removing the Display Assembly.........................................................................................................24

Installing the Display Assembly...........................................................................................................27

Removing the Display Bezel............................................................................................................... 27

Installing the Display Bezel.................................................................................................................30

Removing the Display Panel...............................................................................................................30

Installing the Display Panel..................................................................................................................31

Removing the Camera.........................................................................................................................31

Installing the Camera.......................................................................................................................... 32

3 System Setup....................................................................................................... 33

System Setup Overview...................................................................................................................... 33

Boot Sequence....................................................................................................................................33

Navigation Keys................................................................................................................................... 33

Updating the BIOS ..............................................................................................................................34

System Setup Options.........................................................................................................................35

4 Troubleshooting................................................................................................. 37

Enhanced Pre-Boot System Assessment (ePSA) Diagnostics............................................................37

Battery Status Lights............................................................................................................................37

Device Status Lights............................................................................................................................38

LED Error Codes..................................................................................................................................38

5 Specifications......................................................................................................40

Technical Specification.......................................................................................................................40

6 Contacting Dell...................................................................................................45

Contacting Dell................................................................................................................................... 45

Working on Your Computer

Before Working Inside Your Computer

Use the following safety guidelines to help protect your computer from potential damage and to help to

ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes

that the following conditions exist:

• You have read the safety information that shipped with your computer.

• A component can be replaced or--if purchased separately--installed by performing the removal

procedure in reverse order.

WARNING: Disconnect all power sources before opening the computer cover or panels. After you

finish working inside the computer, replace all covers, panels, and screws before connecting to

the power source.

WARNING: Before working inside your computer, read the safety information that shipped with

your computer. For additional safety best practices information, see the Regulatory Compliance

Homepage at www.dell.com/regulatory_compliance

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or

by periodically touching an unpainted metal surface, such as a connector on the back of the

computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts

on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a

processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable

itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable,

press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep

them evenly aligned to avoid bending any connector pins. Also, before you connect a cable,

ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear differently than shown in

this document.

To avoid damaging your computer, perform the following steps before you begin working inside the

computer.

1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

2. Turn off your computer (see Turning off Your Computer).

3. If the computer is connected to a docking device (docked), undock it.

CAUTION: To disconnect a network cable, first unplug the cable from your computer and

then unplug the cable from the network device.

4. Disconnect all network cables from the computer.

5. Disconnect your computer and all attached devices from their electrical outlets.

6. Close the display and turn the computer upside-down on a flat work surface.

NOTE: To avoid damaging the system board, you must remove the main battery before you

service the computer.

7. Remove the main battery.

8. Turn the computer top-side up.

9. Open the display.

10. Press the power button to ground the system board.

CAUTION: To guard against electrical shock, always unplug your computer from the

electrical outlet before opening the display.

CAUTION: Before touching anything inside your computer, ground yourself by touching an

unpainted metal surface, such as the metal at the back of the computer. While you work,

periodically touch an unpainted metal surface to dissipate static electricity, which could

harm internal components.

11. Remove any installed ExpressCards or Smart Cards from the appropriate slots.

Turning Off Your Computer

CAUTION: To avoid losing data, save and close all open files and exit all open programs before

you turn off your computer.

1. Shut down the operating system:

• Windows 8:

– Point to upper-right corner of the screen and click Settings. Click on the and then select

Shut down.

• In Windows 7:

1. Click Start .

2. Click Shut Down.

1. Click Start .

2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click

Shut Down..

2. Ensure that the computer and all attached devices are turned off. If your computer and attached

devices did not automatically turn off when you shut down your operating system, press and hold

the power button for about 4 seconds to turn them off.

After Working Inside Your Computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and

cables before turning on your computer.

CAUTION: To avoid damage to the computer, use only the battery designed for this particular

Dell computer. Do not use batteries designed for other Dell computers.

1. Connect any external devices, such as a port replicator or media base, and replace any cards, such as

an ExpressCard.

2. Connect any telephone or network cables to your computer.

CAUTION: To connect a network cable, first plug the cable into the network device and then

plug it into the computer.

3. Replace the battery.

4. Connect your computer and all attached devices to their electrical outlets.

5. Turn on your computer.

Removing and Installing Components

This section provides detailed information on how to remove or install the components from your

computer.

Recommended Tools

The procedures in this document may require the following tools:

• Small flat-blade screwdriver

• Phillips screwdriver

• Small plastic scribe

System Overview

1. camera-status light

2. camera

3. microphone

4. power-status light

5. battery-status light

6. hard-drive activity light

7. power button

8. HDMI connector

9. USB 3.0 connector

10. network connector

11. headset connector

12. fingerprint reader

13. microphones

14. touchpad

15. memory card reader

16. USB 3.0 connector

17. USB 3.0 connector with PowerShare

18. power connector

19. security-cable slot

20. service-tag label

21. sub-woofer speaker

22. speakers

Removing the Base Cover

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the screws that secure the base cover to the computer.

3. Pry the base cover along the edges to loosen it.

4. Lift and remove the base cover from the computer.

Installing the Base Cover

1. Place the base cover to align with the screw holes on the computer.

2. Tighten the screws to secure the base cover to the computer.

3. Follow the procedures in After Working Inside Your computer.

Removing the Battery

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the base cover.

3. Disconnect the battery cable from its connector on the system board.

4. Release the tabs that secure the battery in the battery bay.

5. Lift and remove the battery from the computer.

Installing the Battery

1. Place the battery into its slot on the computer.

2. Connect the battery cable to its connector on the system board.

3. Install the base cover.

4. Follow the procedures in After Working Inside Your computer.

Removing the Hard Disk Drive

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove :

a. base cover

b. battery

3. Lift the hard drive assembly in an upward direction to release it from its compartment on the

computer. Remove the hard drive from the computer.

4. Remove the screws that secure the hard drive to the hard drive assembly.

a. Lift and remove the hard drive from the hard drive assembly.

Installing the Hard Drive

1. Place the hard drive assembly into its slot on the computer.

2. Tighten the screw that secures the hard drive to the computer

3. Install:

a. battery

b. base cover

4. Follow the procedures in After Working Inside Your computer

Removing the Coin-Cell Battery

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove :

a. base cover

b. battery

3. Perform the steps as shown in the illustration:

a. Disconnect the coin-cell battery cable from its connector on the system board.

b. Unroute the coin-cell battery cable from the routing channel.

c. Lift and remove the coin-cell from the computer.

Installing the Coin-Cell Battery

1. Place the coin-cell battery into its slot on the computer.

2. Route the coin-cell battery cable along the routing channel.

3. Connect the coin-cell battery cable to its connector on the system board.

4. Install :

a. battery

b. base cover

5. Follow the procedures in After Working Inside Your computer

Removing the WLAN Card

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. base cover

b. battery

3. Perform the steps as shown in the illustration:

a. Disconnect the antenna cable from the WLAN card.

b. Remove the screw that secures the WLAN card to the computer.

c. Remove the WLAN card from its slot on the system board.

Installing the WLAN Card

1. Insert the WLAN card into its connector at a 45–degree angle.

2. Tighten the screw to secure the WLAN card to the computer.

3. Connect the antenna cables to their respective connectors marked on the WLAN card.

4. Install:

a. battery

b. base cover

5. Follow the procedures in After Working Inside Your computer.

Removing the System Fan

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. base cover

b. battery

3. Perform the steps as shown in the illustration:

a. Disconnect the left system fan cable from its connector on the system board.

b. Remove the screws that secure the left system fan to the system board.

4. Lift and remove the left system fan from the computer.

5. Disconnect the right system fan cable from its connector on the system board. Peel away the system

board flex cable from the right system fan.

6. Remove the screws that secure the right system fan to the system board.

7. Lift and remove the right system fan from the computer.

Installing the System Fan

1. Place the right system fan into its original position in the system board and affix the system board flex

cable.

2. Tighten the screws that secure the right system fan to the system board.

3. Connect the right system fan cable to its connector on the system board.

4. Place the left system fan into its original position in the system board.

5. Tighten the screws that secure the left system fan to the system board.

6. Connect the left system fan cable to its connector on the system board.

7. Install :

a. battery

b. base cover

8. Follow the procedures in After Working Inside Your computer.

Removing the Heatsink

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. base cover

b. battery

c. system fan

3. Remove the screws that secure the heatsink to the system board.

4. Lift up the heatsink and remove from the computer.

Installing the Heatsink

1. Place the heatsink into its original position on the system board.

2. Tighten the screws to secure the heatsink to the system board.

3. Install:

a. system fan

b. battery

c. base cover

4. Follow the procedures in After Working Inside Your computer

Removing the Memory Module

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. base cover

b. battery

c. system fan

d. heatsink

3. Pry the retention clips away from the memory module until it pops up. Remove the memory module

from its connector on the system board.

Installing the Memory

1. Insert the memory module into the memory socket.

2. Press the memory module down until it clicks into place.

3. Install:

a. heatsink

b. system fan

c. battery

d. base cover

4. Follow the procedures in After Working Inside Your computer.

Removing the System Board

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove :

a. base cover

b. battery

c. system fan

d. heatsink

e. memory

3. Disconnect the following cables:

a. speaker

b. display

c. keyboard

d. touchpad

e. camera

4. Remove the screws that secure the system board to the chassis.

5. Remove the system board from the computer.

Installing the System Board

1. Place the system board into its original position on the chassis.

2. Install the screws that secure the system board to the chassis.

3. Connect :

a. camera cable

b. touchpad cable

c. keyboard cable

d. display cable

e. speaker cable

4. Install :

a. memory

b. heatsink

c. system fan

d. battery

e. base cover

5. Follow the procedures in After Working Inside Your computer

Removing the Display Assembly

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove :

a. base cover

b. battery

3. Disconnect the LVDS cable and the camera cable from its connectors on the system board.

4. Remove the screws that secure the display hinges to the system board. Lift and move the system

base panel away from the display hinges to facilitate easy removal of the display assembly.

5. Detach the base panel from the display assembly..

Installing the Display Assembly

1. Align the base panel of the computer to the display hinges.

2. Install the screws that secure the display hinges to the base panel

3. Connect the LVDS cable and the camera cable to the connectors on the system board.

4. Install :

a. battery

b. base cover

5. Follow the procedures in After Working Inside Your computer

Removing the Display Bezel

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove :

a. base cover

b. battery

c. display assembly

3. Rotate the hinge brackets at the angle shown to facilitate easy removal of the display bezel.

4. Pry on the plastic caps that cover the display bezel screws and remove them.

5. Remove the screws that secure the display bezel.

6. Pry along the inner edges of the display bezel and remove it.

Installing the Display Bezel

1. Align the display bezel by pressing along the edges.

2. Install the screws that secure the display bezel.

3. Install the plastic caps that secure the display bezel screws on both sides of the display bezel.

4. Install :

a. battery

b. base cover

c. display assembly

5. Follow the procedures in After Working Inside Your computer.

Removing the Display Panel

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. base cover

b. battery

c. display assembly

d. display bezel

3. Remove the screws that secure the display panel to the display assembly.

4. Lift and remove the display panel from the display assembly.

Installing the Display Panel

1. Align the display panel to the display assembly by pressing along the edges.

2. Install the screws that secure the display panel.

3. Install:

a. battery

b. base cover

c. display assembly

d. display bezel

4. Follow the procedures in After Working Inside Your computer.

Removing the Camera

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove :

a. base cover

b. battery

c. display assembly

d. display bezel

e. display

3. Disconnect the camera cable and lift the camera to remove it from the computer.

Installing the Camera

1. Align the camera to the display panel .

2. Connect the camera cable to the camera.

3. Install :

a. battery

b. base cover

c. display assembly

d. display bezel

e. display

4. Follow the procedures in After Working Inside Your computer

System Setup

System Setup Overview

System Setup allows you to:

• change the system configuration information after you add, change, or remove any hardware in your

computer.

• set or change a user-selectable option such as the user password.

• read the current amount of memory or set the type of hard drive installed.

• check battery health.

Before you use System Setup, it is recommended that you write down the System Setup screen

information for future reference.

CAUTION: Unless you are an expert computer user, do not change the settings for this program.

Certain changes can cause your computer to work incorrectly.

Boot Sequence

Boot Sequence allows you to bypass the System Setup‐defined boot device order and boot directly to a

specific device (for example: optical drive or hard drive). During the Power-on Self Test (POST), when the

Dell logo appears, you can:

• Access System Setup by pressing <F2> key

• Bring up the one-time boot menu by pressing <F12> key

The one-time boot menu displays the devices that you can boot from including the diagnostic option.

The boot-menu options are:

• Removable Drive (if available)

• STXXXX Drive

NOTE: XXX denotes the SATA drive number.

• Optical Drive

• Diagnostics

NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.

The boot sequence screen also displays the option to access the System Setup screen.

Navigation Keys

The following table displays the system setup navigation keys.

NOTE: For most of the system setup options, changes that you make are recorded but do not take

effect until you re-start the system.

Table 1. Navigation Keys

Keys Navigation

Up arrow Moves to the previous field.

Down arrow Moves to the next field.

<Enter> Allows you to select a value in the selected field (if applicable) or follow the link in

the field.

Spacebar Expands or collapses a drop‐down list, if applicable.

<Tab> Moves to the next focus area.

NOTE: For the standard graphics browser only.

<Esc> Moves to the previous page till you view the main screen. Pressing <Esc> in the main

screen displays a message that prompts you to save any unsaved changes and

restarts the system.

<F1> Displays the System Setup help file.

Updating the BIOS

It is recommended to update your BIOS (system setup), on replacing the system board or if an update is

available. For laptops, ensure that your computer battery is fully charged and connected to a power

outlet

1. Re-start the computer.

2. Go to dell.com/support.

3. Enter the Service Tag or Express Service Code and click Submit.

NOTE: To locate the Service Tag, click Where is my Service Tag?

NOTE: If you cannot find your Service Tag, click Detect My Product. Proceed with the

instructions on screen.

4. If you are unable to locate or find the Service Tag, click the Product Category of your computer.

5. Choose the Product Type from the list.

6. Select your computer model and the Product Support page of your computer appears.

7. Click Get drivers and click View All Drivers.

The Drivers and Downloads page opens.

8. On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS.

9. Identify the latest BIOS file and click Download File.

You can also analyze which drivers need an update. To do this for your product, click Analyze

System for Updates and follow the instructions on the screen.

10. Select your preferred download method in the Please select your download method below window,

click Download File.

The File Download window appears.

11. Click Save to save the file on your computer.

12. Click Run to install the updated BIOS settings on your computer.

Follow the instructions on the screen.

System Setup Options

Main

Table 2. Main

System Time Re-sets the time on the computer's internal clock.

System Date Re-sets the date on the computer's internal

calendar.

BIOS Version Displays the BIOS revision.

Product Name Displays the product name and the model number.

Service Tag Displays the service tag of your computer.

Asset Tag Displays the asset tag of your computer (if

available).

CPU Type Displays the type of processor.

CPU Speed Displays the speed of the processor.

CPU ID Displays the processor ID.

L1 Cache Displays the processor L1 cache size.

L2 Cache Displays the processor L2 cache size.

L3 Cache Displays the processor L3 cache size.

Fixed HDD Displays the model number and capacity of the

hard drive.

System Memory Displays the memory in-built on the computer.

Extended Memory Displays the memory installed on the computer.

Memory Speed Displays the memory speed.

Advanced

Table 3. Advanced

Intel SpeedStep Enable or disable the Intel

SpeedStep feature.

Default: Enabled

Virtualization Enable or disable the Intel

Virtualization feature.

Default: Enabled

Integrated NIC Enable or disable the power

supply to the on–board network

card.

Default: Enabled

USB Emulation Enable or disable the USB

emulation feature.

Default: Enabled

USB PowerShare Enable or disable the USB

PowerShare feature.

Default: Enabled

USB Wake Support Enable or disable the USB wake

support feature

Default: Disabled

SATA Operation Change the SATA controller

mode to either ATA or AHCI.

Default: AHCI

Adapter Warnings Enable or disable the Adapter

Warnings.

Default: Enable

Function Key Behavior Specifies the behavior of the

function key <Fn>.

Default: Function key

Battery Health Displays a message about the

battery health.

Miscellaneous Devices These fields let you enable or

disable various on-board devices.

Security

Table 4. Security

Set Asset Tag This field displays your system's asset tag. If the

asset tag is not already set, this field can be used to

enter it.

Set Admin Password Allows you to change or delete the administrator

password.

Set System Password Allows you to change or delete the system

password.

Set HDD Password Allows you to set a password on the computer's

internal hard drive (HDD).

Password Change Allows you to change the security password.

Password Bypass Allows you to bypass the system password and the

internal HDD password prompts during a system

restart/resume from hibernate state.

Boot

Table 5. Boot

Boot Priority Order Specifies the order of different devices in which the

computer will boot through at start up.

Legacy Boot Option Allows you to load legacy option. (Default:

Enabled)

Secure Boot Species if the UEFI secure boot option (Default:

Disabled)

Add Boot Option Allows the user to add an additional boot device.

Delete Boot Option Allows the user to remove an existing boot device

from the boot order.

Exit

This section allows you to save, discard, and load default settings before exiting from System Setup.

Troubleshooting

Enhanced Pre-Boot System Assessment (ePSA)

Diagnostics

The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware.

The ePSA is embedded with the BIOS and is launched by the BIOS internally. The embedded system

diagnostics provides a set of options for particular devices or device groups allowing you to:

• Run tests automatically or in an interactive mode

• Repeat tests

• Display or save test results

• Run thorough tests to introduce additional test options to provide extra information about the failed

device(s)

• View status messages that inform you if tests are completed successfully

• View error messages that inform you of problems encountered during testing

CAUTION: Use the system diagnostics to test only your computer. Using this program with other

computers may cause invalid results or error messages.

NOTE: Some tests for specific devices require user interaction. Always ensure that you are present

at the computer terminal when the diagnostic tests are performed.

1. Power-on the computer.

2. As the computer boots, press the <F12> key as the Dell logo appears.

3. On the boot menu screen, select the Diagnostics option.

The Enhanced Pre-boot System Assessment window is displayed, listing all devices detected in the

computer. The diagnostics starts running the tests on all the detected devices.

4. If you wish to run a diagnostic test on a specific device, press <Esc> and click Yes to stop the

diagnostic test.

5. Select the device from the left pane and click Run Tests.

6. If there are any issues, error codes are displayed.

Note the error code and contact Dell.

Battery Status Lights

Table 6. Battery LED Behavior

Battery Charge LED Off/Hibernate Standby

AC mode Full charge Off Off

Charging Solid White Solid White

Battery Charge LED Off/Hibernate Standby

Battery mode Discharging when Battery

charge is > 10%

Off Off

Discharging when Battery

charge is <=10%

Off Blinking White

Device Status Lights

Turns on when you turn on the computer and blinks when the computer is in a power

management mode.

Turns on when the computer reads or writes data.

Turns on steadily or blinks to indicate battery charge status.

LED Error Codes

Diagnostic LED codes are communicated via the Power Button LED. The Power Button LED blinks the

corresponding LED codes for the corresponding fault condition. Example: For No Memory detected (LED

code 2) , The Power Button LED blinks two times followed by a pause, blinks two times, pause, etc. This

pattern continues until the system is powered off.

Code Cause and Troubleshooting Steps

1System board: BIOS ROM failure

System board failure, covers BIOS corruption or ROM error

2Memory

No memory/RAM detected

3Chipset Error (North and South Bridge Chipset, DMA/IMR/ Timer Error) , Time-Of-

Day Clock test failure , Gate A20 failure , Super I/O chip failure , Keyboard

controller test failure

System board failure

4RAM Read/Write failure

Memory failure

5Real-time clock power fail

CMOS battery failure

6Video BIOS test failure

Video card failure

Code Cause and Troubleshooting Steps

7CPU - cache test failure

Processor failure

8Display

Display failure

Specifications

Technical Specification

NOTE: Offerings may vary by region. For more information regarding the configuration of your

computer, click Start (Start icon) → Help and Support, and then select the option to view

information about your computer.

NOTE: In Windows 8, navigate to Help and Support to view information about your computer.

Table 7. System Information

Feature Description

Chipset Intel i3, i5, i7 Series

DRAM bus width 64–bit

Flash EPROM W25Q64FVSSIQ

Table 8. Processor

Feature Description

L3 smart cache 3 MB and 4 MB

Table 9. Memory

Feature Description

Memory connector HM87

Memory capacity 8 GB

Memory type DDRL, SO-DIMM

Memory Controller Broadwell U

Minimum memory 4 GB

Maximum memory 8 GB

Table 10. Audio

Feature Description

Type two 1.5 watt speakers and one 2 watt subwoofer

Controller Realtek ALC290Q

Feature Description

Internal microphone supports Digital microphone x 2

Speakers 3

Volume controls Program menus and keyboard shortcut keys

Table 11. Video

Feature Description

Video type UMA/DIS

Video Controller:

UMA Intel HD graphics 5x00

Discrete Nvidia N15S-GM

Data bus 64–bit

External display support HDMI

Table 12. Camera

Feature Description

Camera Resolution 1 Megapixel

Video Resolution (maximum) 1280 x 720 pixels

Diagonal viewing angle 74–degree

Table 13. Communication

Feature Description

Network adapter Ethernet 10/100/1000 Base-T

Wireless w-fi 802.11 agn/ac

Table 14. Ports and Connectors

Feature Description

Audio combo jack

Video HDMI

Network adapter RJ–45

USB two USB 3.0, one USB 3.0 PowerShare port

Media card reader SD

Table 15. Display

Feature Description

Type HD

Dimensions:

Height 206.44 mm (8.12 inches)

Width 326.18 mm (12.84 inches)

Diagonal 14.0"

Active area (X/Y) 309.4 mm (12.18 inches) x

173.95 mm (6.84 inches)

Maximum resolution 1366 x 768 pixels

Maximum Brightness 200 nits

Operating angle 135–degree

Refresh rate 60Hz /40Hz

Minimum Viewing angles:

Horizontal 40(L)/40( R)

Vertical 10(up)/30(down)

Pixel pitch 0.2265 (H) x 0.2265 (V)

Table 16. Keyboard

Feature Description

Number of keys 80

Table 17. Touchpad

Feature Description

Active Area:

X-axis 111.40 mm (4.38 inches)

Y-axis 76.40 mm (3 inches)

Table 18. Battery

Feature Description

Type ICP666480

Dimensions:

Height 99.5 mm (3.91 inches)

Width 198.5 mm (7.81 inches)

Depth 7.5 mm (0.30 inch)

Feature Description

Weight 269 grams (0.60 lb)

Charge time 3 hour

Voltage 11.4 V

Temperature range:

Operating 0 ℃ to 50 ℃

Non-Operating 0 ℃ to 65 ℃

Coin-cell battery LI 3V 83 MAH

Table 19. AC Adapter

Feature Description

Type AC adapter

Input voltage 90 ~ 264 VAC

Input current (maximum) 1.6 A / 1.5 A

Input frequency 50 Hz–60 Hz

Output power 65 W

Output current 0 A to 3.34 A

Rated output voltage 19.5 V

Temperature range:

Operating 0 ℃ to 40 ℃

Non-Operating 95 ℃

Table 20. Physical

Feature Non-Touch Touch

Height 18.30 mm (0.72 inch) 19.35 mm (0.76 inch)

Width 337.60 mm (13.29 inches) 337.60 mm (13.29 inches)

Depth 233.50 mm (9.19 inch) 233.50 mm (9.19 inch)

Weight (minimum) 1.53 kg (3.37 lb) 1.62 kg (3.57 lb)

Table 21. Environmental

Feature Description

Temperature:

Operating 0 ℃ to 35 ℃

Storage -20 ℃ to 60 ℃

Relative humidity (maximum):

Feature Description

Operating 20% – 90%

Storage 20% – 95%

Altitude (maximum):

Operating –15.2 m to 3048 m (–50 to 10,000 ft)

0° to 35°C

Non-Operating –15.2 m to 10,668 m (–50 ft to 35,000 ft)

Airborne contaminant level G2 or lower as defined by ISA - S71.04 – 1985

Contacting Dell

NOTE: If you do not have an active Internet connection, you can find contact information on your

purchase invoice, packing slip, bill, or Dell product catalog.

Dell provides several online and telephone-based support and service options. Availability varies by

country and product, and some services may not be available in your area. To contact Dell for sales,

technical support, or customer service issues:

1. Go to dell.com/support.

2. Select your support category.

3. Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the

page.

4. Select the appropriate service or support link based on your need.

Table of Contents

DELL 5480 User Manual

Related Manuals