DELL 5510 User Manual

Displayed below is the user manual for 5510 by DELL which is a product in the Notebooks category. This manual has pages.

Related Manuals

DELL 5510 Manual

Vostro 15 5510

Service Manual

Regulatory Model: P106F

Regulatory Type: P106F001

April 2021

Rev. A00

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

trademarks may be trademarks of their respective owners.

Chapter 1: Working on your computer........................................................................................... 6

Safety instructions.............................................................................................................................................................. 6

Working inside your computer.................................................................................................................................... 6

Entering Service Mode................................................................................................................................................. 8

Exiting Service Mode.................................................................................................................................................... 9

After working inside your computer..........................................................................................................................9

Chapter 2: Removing and installing components.......................................................................... 10

Recommended tools..........................................................................................................................................................10

Screw list............................................................................................................................................................................. 10

Major components of your system................................................................................................................................ 12

Base cover........................................................................................................................................................................... 13

Removing the base cover...........................................................................................................................................13

Installing the base cover.............................................................................................................................................14

Battery.................................................................................................................................................................................. 16

Lithium-ion battery precautions............................................................................................................................... 16

Removing the 3-cell battery...................................................................................................................................... 17

Installing the 3-cell battery........................................................................................................................................ 17

Removing the 4-cell battery...................................................................................................................................... 18

Installing the 4-cell battery........................................................................................................................................ 19

Battery cable...................................................................................................................................................................... 20

Removing the battery cable......................................................................................................................................20

Installing the battery cable.........................................................................................................................................21

Memory................................................................................................................................................................................22

Removing the memory module.................................................................................................................................22

Installing the memory module................................................................................................................................... 23

Solid-state drive—M.2 slot one.................................................................................................................................... 25

Removing the 2230 solid-state drive from M.2 slot one................................................................................... 25

Installing the 2230 solid-state drive in M.2 slot one...........................................................................................25

Removing the 2280 solid-state drive from M.2 slot one................................................................................... 26

Installing the 2280 solid-state drive in M.2 slot one........................................................................................... 27

Installing the solid-state drive mounting bracket on M.2 slot one.................................................................. 28

Solid-state drive—M.2 slot two....................................................................................................................................29

Removing the 2230 solid-state drive from M.2 slot two...................................................................................29

Installing the 2230 solid-state drive in M.2 slot two........................................................................................... 31

Wireless card...................................................................................................................................................................... 33

Removing the wireless card...................................................................................................................................... 33

Installing the wireless card........................................................................................................................................ 34

Fan........................................................................................................................................................................................ 35

Removing the fan........................................................................................................................................................ 35

Installing the fan.......................................................................................................................................................... 36

Coin-cell battery................................................................................................................................................................ 37

Removing the coin-cell battery................................................................................................................................ 37

Installing the coin-cell battery.................................................................................................................................. 37

Contents

Contents 3

Heat sink..............................................................................................................................................................................38

Removing the heatsink...............................................................................................................................................38

Installing the heatsink.................................................................................................................................................39

Network-port bracket...................................................................................................................................................... 40

Removing the network-port bracket...................................................................................................................... 40

Installing the network-port bracket......................................................................................................................... 41

I/O board............................................................................................................................................................................. 42

Removing the I/O board............................................................................................................................................ 42

Installing the I/O board.............................................................................................................................................. 43

Speakers.............................................................................................................................................................................. 44

Removing the speakers..............................................................................................................................................44

Installing the speakers................................................................................................................................................45

Touchpad............................................................................................................................................................................. 47

Removing the touchpad............................................................................................................................................. 47

Installing the touchpad............................................................................................................................................... 47

Display assembly................................................................................................................................................................49

Removing the display assembly............................................................................................................................... 49

Installing the display assembly ................................................................................................................................ 50

Power button with optional fingerprint reader.......................................................................................................... 52

Removing the power button with optional fingerprint reader..........................................................................52

Installing the power button with optional fingerprint reader............................................................................ 52

Power-adapter port.......................................................................................................................................................... 53

Removing the power-adapter port......................................................................................................................... 53

Installing the power-adapter port............................................................................................................................54

System board..................................................................................................................................................................... 55

Removing the system board.....................................................................................................................................55

Installing the system board....................................................................................................................................... 58

Palm-rest and keyboard assembly................................................................................................................................ 62

Removing the palm-rest and keyboard assembly................................................................................................ 62

Installing the palm-rest and keyboard assembly.................................................................................................. 63

Chapter 3: Drivers and downloads............................................................................................... 65

Downloading the drivers..................................................................................................................................................65

Chapter 4: System setup.............................................................................................................66

BIOS overview................................................................................................................................................................... 66

Entering BIOS setup program........................................................................................................................................ 66

Navigation keys..................................................................................................................................................................66

Boot Sequence...................................................................................................................................................................67

Advanced or Engineering configurations..................................................................................................................... 67

SupportAssist system resolution................................................................................................................................... 67

System setup options.......................................................................................................................................................68

Updating the BIOS in Windows .....................................................................................................................................77

Updating BIOS on systems with BitLocker enabled............................................................................................ 77

Updating the Dell BIOS in Linux and Ubuntu environments.............................................................................. 77

Flashing BIOS (USB key)........................................................................................................................................... 77

System and setup password...........................................................................................................................................78

Assigning a system setup password....................................................................................................................... 78

Deleting or changing an existing system setup password................................................................................. 79

4Contents

Chapter 5: Troubleshooting.........................................................................................................80

Dell SupportAssist Pre-boot System Performance Check diagnostics................................................................80

Running the SupportAssist Pre-Boot System Performance Check................................................................80

System diagnostic lights...................................................................................................................................................81

Recovering the operating system................................................................................................................................. 82

Flashing BIOS (USB key).................................................................................................................................................82

Flashing the BIOS..............................................................................................................................................................83

WiFi power cycle............................................................................................................................................................... 83

Flea power release............................................................................................................................................................ 83

Chapter 6: Getting help...............................................................................................................84

Contacting Dell.................................................................................................................................................................. 84

Contents 5

Working on your computer

Topics:

•Safety instructions

Safety instructions

Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless

otherwise noted, each procedure included in this document assumes that you have read the safety information that shipped

with your computer.

WARNING: Before working inside your computer, read the safety information that is shipped with your

computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/

regulatory_compliance.

WARNING: Disconnect your computer from all power sources before opening the computer cover or panels.

After you finish working inside the computer, replace all covers, panels, and screws before connecting your

computer to an electrical outlet.

CAUTION: To avoid damaging the computer, ensure that the work surface is flat, dry, and clean.

CAUTION: To avoid damaging the components and cards, handle them by their edges, and avoid touching the

pins and the contacts.

CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical

assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the

safety instructions that is shipped with the product or at www.dell.com/regulatory_compliance.

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal

surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal

surface to dissipate static electricity which could harm internal components.

CAUTION: When you disconnect a cable, pull it by its connector or its pull tab, not the cable itself. Some cables

have connectors with locking tabs or thumbscrews that you must disengage before disconnecting the cable.

When disconnecting cables, keep them evenly aligned to avoid bending the connector pins. When connecting

cables, ensure that the ports and the connectors are correctly oriented and aligned.

CAUTION: Press and eject any installed card from the media-card reader.

NOTE: The color of your computer and certain components may appear differently than shown in this document.

Working inside your computer

Before working inside your computer

About this task

NOTE: The images in this document may differ from your computer depending on the configuration you ordered.

6 Working on your computer

Steps

1. Save and close all open files and exit all open applications.

2. Shut down your computer. Click Start > Power > Shut down.

NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down

instructions.

3. Disconnect your computer and all attached devices from their electrical outlets.

4. Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.

CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the

cable from the network device.

5. Remove any media card and optical disc from your computer, if applicable.

Electrostatic discharge—ESD protection

ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards,

processors, memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such

as intermittent problems or a shortened product life span. As the industry pushes for lower power requirements and increased

density, ESD protection is an increasing concern.

Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than

in previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.

Two recognized types of ESD damage are catastrophic and intermittent failures.

●Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes

an immediate and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has

received a static shock and immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or

nonfunctional memory.

●Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of

intermittent failures means that most of the time when damage occurs, it is not immediately recognizable. The DIMM

receives a static shock, but the tracing is merely weakened and does not immediately produce outward symptoms related to

the damage. The weakened trace may take weeks or months to melt, and in the meantime may cause degradation of memory

integrity, intermittent memory errors, etc.

The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded")

failure.

Perform the following steps to prevent ESD damage:

●Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do not

provide adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts

with increased sensitivity to ESD damage.

●Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.

●When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static

packing material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you

discharge static electricity from your body.

●Before transporting a static-sensitive component, place it in an anti-static container or packaging.

ESD field service kit

The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components:

anti-static mat, wrist strap, and bonding wire.

Components of an ESD field service kit

The components of an ESD field service kit are:

●Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an

anti-static mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal

on the system being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly

on the mat. ESD-sensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.

Working on your computer 7

●Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist

and bare metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that

is temporarily placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD

mat, and the hardware is known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never

use wireless wrist straps. Always be aware that the internal wires of a wrist strap are prone to damage from normal wear

and tear, and must be checked regularly with a wrist strap tester in order to avoid accidental ESD hardware damage. It is

recommended to test the wrist strap and bonding wire at least once per week.

●ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored

kit, it is a best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A

wrist strap tester is the best method for doing this test. If you do not have your own wrist strap tester, check with your

regional office to find out if they have one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is

strapped to your wrist and push the button to test. A green LED is lit if the test is successful; a red LED is lit and an alarm

sounds if the test fails.

●Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts

that are insulators and often highly charged.

●Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For

example, deploying the kit for a server environment is different than for a desktop or portable environment. Servers are

typically installed in a rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always

look for a large open flat work area that is free of clutter and large enough to deploy the ESD kit with additional space to

accommodate the type of system that is being repaired. The workspace should also be free of insulators that can cause an

ESD event. On the work area, insulators such as Styrofoam and other plastics should always be moved at least 12 inches or

30 centimeters away from sensitive parts before physically handling any hardware components

●ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded

bags are preferred. However, you should always return the damaged part using the same ESD bag and packaging that the

new part arrived in. The ESD bag should be folded over and taped shut and all the same foam packing material should be

used in the original box that the new part arrived in. ESD-sensitive devices should be removed from packaging only at an

ESD-protected work surface, and parts should never be placed on top of the ESD bag because only the inside of the bag is

shielded. Always place parts in your hand, on the ESD mat, in the system, or inside an anti-static bag.

●Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts

to be returned to Dell, it is critical to place these parts in anti-static bags for safe transport.

ESD protection summary

It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static

mat at all times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all

insulator parts while performing service and that they use anti-static bags for transporting sensitive components.

Transporting sensitive components

When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place

these parts in anti-static bags for safe transport.

Entering Service Mode

Service Mode allows users to immediately cut off electricity from the computer and conduct repairs without disconnecting the

battery cable from the system board.

To enter Service Mode:

1. Shut down your computer and disconnect the AC adapter.

2. Hold <B> key on the keyboard and press the power button for 3 seconds or until the Dell logo appears on the screen.

3. Press any key to continue.

NOTE: If the power adapter has not been disconnected, a message prompting you to remove the AC adapter appears

on the screen. Remove the AC adapter and then press any key to continue the Service Mode procedure.

NOTE: The Service Mode procedure automatically skips the following step if the Owner Tag of the computer is not

set up in advance by the manufacturer.

4. When the ready-to-proceed message appears on the screen, press any key to proceed. The computer emits three short

beeps and shuts down immediately.

8Working on your computer

Once the computer shuts down, you may perform the replacement procedures without disconnecting the battery cable from

the system board.

Exiting Service Mode

Service Mode allows users to immediately cut off electricity from the computer and conduct repairs without disconnecting the

battery cable from the system board.

To exit Service Mode:

1. Connect the AC adapter to the power-adapter port on your computer.

2. Press the power button to turn on the computer. Your computer will automatically return to normal functioning mode.

After working inside your computer

About this task

CAUTION: Leaving stray or loose screws inside your computer may severely damage your computer.

Steps

1. Replace all screws and ensure that no stray screws remain inside your computer.

2. Connect any external devices, peripherals, or cables you removed before working on your computer.

3. Replace any media cards, discs, or any other parts that you removed before working on your computer.

4. Connect your computer and all attached devices to their electrical outlets.

5. Turn on your computer.

Working on your computer 9

Removing and installing components

NOTE: The images in this document may differ from your computer depending on the configuration you ordered.

Topics:

•Recommended tools

•Screw list

•Major components of your system

•Base cover

•Battery

•Battery cable

•Memory

•Solid-state drive—M.2 slot one

•Solid-state drive—M.2 slot two

•Wireless card

•Fan

•Coin-cell battery

•Heat sink

•Network-port bracket

•I/O board

•Speakers

•Touchpad

•Display assembly

•Power button with optional fingerprint reader

•Power-adapter port

•System board

•Palm-rest and keyboard assembly

Recommended tools

The procedures in this document may require the following tools:

●Phillips screwdriver #0

●Plastic scribe

Screw list

NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and

then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type is

restored when the component is replaced.

NOTE: Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surface when

replacing a component.

NOTE: Screw color may vary with the configuration ordered.

Table 1. Screw list

10 Removing and installing components

Table 1. Screw list

Component Screw type Quantity Screw image

Base cover ●Captive screws -

M2x7.5

●M2x4

●2

●7

●

3-cell battery M2x3 3

4-cell battery M2x3 4

Wireless card M2x3 1

Solid-state drive - Slot 1 M2x3 1

Solid-state drive - Slot 2 M2x3 1

Fan M2x3 2

Heat sink Captive screws 4

System board M2x2 3

USB Type-C bracket M2x4 2

Power button with fingerprint

reader

M2x3 1

Network-port bracket M2x5 2

I/O board M2x2 1

Touchpad M1.6x2

M2x1.8

Power-adapter port M2.5x4.5 3

Display assembly M2.5x4.5 6

Removing and installing components 11

Major components of your system

1. Base cover

2. Heat sink

3. System board

4. Memory module

5. Battery

6. Speakers

7. Palm-rest and keyboard assembly

8. Touchpad

9. Display assembly

10. Coin-cell battery

11. I/O board

12. M.2 2280 SSD card

12 Removing and installing components

13. WLAN

14. M.2 2230 SSD card

15. Power button with optional fingerprint reader

16. Fan

17. Power-adapter port

NOTE: Dell provides a list of components and their part numbers for the original system configuration purchased. These

parts are available according to warranty coverages purchased by the customer. Contact your Dell sales representative for

purchase options.

Base cover

Removing the base cover

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

About this task

The following images indicate the location of the base cover and provide a visual representation of the removal procedure.

Removing and installing components 13

Steps

1. Loosen the two (M2x7.5) captive screws that secure the base cover to the palm-rest and keyboard assembly.

2. Remove the seven (M2x4) screws that secure the base cover to the palm-rest and keyboard assembly.

3. Using a plastic scribe, pry the base cover from the U-shaped indents at the top edge of the base cover and continue to work

on the sides to release the base cover from the palm-rest and keyboard assembly.

4. Lift the base cover off the palm-rest and keyboard assembly.

Installing the base cover

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following images indicate the location of the base cover and provide a visual representation of the installation procedure.

14 Removing and installing components

Removing and installing components 15

Steps

1. Place the base cover on top of the palm-rest and keyboard assembly.

2. Align the screw holes on the base cover with the screw holes on the palm-rest and keyboard assembly, and then snap the

base cover into place.

3. Tighten the two (M2x7.5) captive screws that secure the base cover to the palm-rest and keyboard assembly.

4. Replace the seven (M2x4) screws that secure the base cover to the palm-rest and keyboard assembly.

Next steps

1. Exit Service Mode.

2. Follow the procedure in After working inside your computer.

Battery

Lithium-ion battery precautions

CAUTION:

●Exercise caution when handling Lithium-ion batteries.

●Discharge the battery completely before removing it. Disconnect the AC power adapter from the system and

operate the computer solely on battery power—the battery is fully discharged when the computer no longer

turns on when the power button is pressed.

●Do not crush, drop, mutilate, or penetrate the battery with foreign objects.

●Do not expose the battery to high temperatures, or disassemble battery packs and cells.

●Do not apply pressure to the surface of the battery.

●Do not bend the battery.

●Do not use tools of any kind to pry on or against the battery.

●Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental

puncture or damage to the battery and other system components.

16 Removing and installing components

●If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing,

bending, or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical

support for assistance. See www.dell.com/contactdell.

●Always purchase genuine batteries from www.dell.com or authorized Dell partners and resellers.

Removing the 3-cell battery

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Remove the base cover.

About this task

The following image indicates the location of the 3-cell (41 Wh) battery and provides a visual representation of the removal

procedure.

Steps

1. Peel the tape that secures the battery cable to the system board.

2. Disconnect the battery cable from the system board.

3. Remove the three (M2x3) screws that secure the 3-cell battery to the palm-rest and keyboard assembly.

4. Lift the 3-cell battery, along with its cable, off the palm-rest and keyboard assembly.

Installing the 3-cell battery

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the 3-cell (41 Wh) battery and provides a visual representation of the installation

procedure.

Removing and installing components 17

Steps

1. Using the alignment posts, place the 3-cell battery on the palm-rest and keyboard assembly.

2. Align the screw holes on the 3-cell battery with the screw holes on the palm-rest and keyboard assembly.

3. Replace the three (M2x3) screws that secure the 3-cell battery to the palm-rest and keyboard assembly.

4. Connect the battery cable to the system board.

5. Adhere the tape that secures the battery cable to the system board.

Next steps

1. Install the base cover.

2. Follow the procedure in After working on your computer.

Removing the 4-cell battery

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Remove the base cover.

About this task

The following image indicates the location of the 4-cell (54 Wh) battery and provides a visual representation of the removal

procedure.

18 Removing and installing components

Steps

1. Peel the tape that secures the battery cable to the system board.

2. Disconnect the battery cable from the system board.

3. Remove the four (M2x3) screws that secure the 4-cell battery to the palm-rest and keyboard assembly.

4. Lift the 4-cell battery, along with its cable, off the palm-rest and keyboard assembly.

Installing the 4-cell battery

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the 4-cell (54 Wh) battery and provides a visual representation of the installation

procedure.

Removing and installing components 19

Steps

1. Using the alignment posts, place the 4-cell battery on the palm-rest and keyboard assembly.

2. Align the screw holes on the 4-cell battery with the screw holes on the palm-rest and keyboard assembly.

3. Replace the four (M2x3) screws that secure the 4-cell battery to the palm-rest and keyboard assembly.

4. Connect the battery cable to the system board.

5. Adhere the tape that secures the battery cable to the system board.

Next steps

1. Install the base cover.

2. Follow the procedure in After working on your computer.

Battery cable

Removing the battery cable

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Remove the base cover.

3. Remove the 3-cell battery or 4-cell battery, whichever applicable.

NOTE: If battery is disconnected from system board for service, then there is a delay during system boot as the system

undergoes RTC battery reset.

About this task

The following images indicate the location of the battery cable and provide a visual representation of the removal procedure.

20 Removing and installing components

Steps

1. Flip the battery and remove the battery cable from the routing guides on the battery.

2. Disconnect the battery cable from the connector on the battery.

3. Lift the battery cable off the battery.

Installing the battery cable

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the battery cable and provides a visual representation of the installation procedure.

Removing and installing components 21

Steps

1. Align and place the battery cable on the battery.

2. Route the battery cable through the routing guides on the battery.

3. Connect the battery cable to the connector on the battery.

Next steps

1. Install the 3-cell battery or 4-cell battery, whichever applicable.

2. Install the base cover.

3. Follow the procedure in After working on your computer.

Memory

Removing the memory module

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

About this task

The following images indicate the location of the memory module and provide a visual representation of the removal procedure.

22 Removing and installing components

Steps

1. Lift the Mylar to access the memory module.

2. Use your fingertips to pull the securing clips from both sides of the memory module until the memory module pops-up.

3. Remove the memory module from the memory-module slot.

NOTE: Repeat step 1 to step 3 to remove any other memory modules installed in your computer.

Installing the memory module

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the memory module and provides a visual representation of the installation

procedure.

Removing and installing components 23

Steps

1. Lift the Mylar to access the memory-module slot.

2. Align the notch on the memory module with the tab on the memory-module slot.

3. Slide the memory module firmly at an angle, into the memory-module slot.

4. Press the memory module down until it clicks into place.

NOTE: If you do not hear the click, remove the memory module and reinstall it.

NOTE: Repeat step 1 to step 4 to install any other memory modules in your computer.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

24 Removing and installing components

Solid-state drive—M.2 slot one

Removing the 2230 solid-state drive from M.2 slot one

Prerequisites

1. Follow the procedure in Before working inside your computer.

NOTE: Solid-state drives are fragile. Exercise care when handling the solid-state drive.

NOTE: To avoid data loss, do not remove the solid-state drive while the computer is in sleep or on state.

2. Enter Service Mode.

3. Remove the base cover.

About this task

NOTE: Depending on the configuration ordered, your computer may support a 2230 solid-state drive, or a 2280 solid-state

drive in M.2 slot one.

NOTE: This procedure applies only to computers shipped with a 2230 solid-state drive installed in M.2 slot one.

The following image indicates the location of the 2230 solid-state drive that is installed in M.2 slot one and provides a visual

representation of the removal procedure.

Steps

1. Remove the screw (M2x3) that secures the 2230 solid-state drive to the palm-rest and keyboard assembly.

2. Slide and remove the solid-state drive from the M.2 slot one.

Installing the 2230 solid-state drive in M.2 slot one

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

Removing and installing components 25

About this task

NOTE: Solid-state drives are fragile. Exercise care when handling the solid-state drive.

NOTE: Depending on the configuration ordered, your computer may support a 2230 solid-state drive, or a 2280 solid-state

drive in M.2 slot one.

NOTE: This procedure applies only if you are installing a 2230 solid-state drive in M.2 slot one.

NOTE: Before installing your 2230 or 2280 solid-state drive, ensure that the mounting bracket is in the correct location. For

more information, see Installing the solid-state drive mounting bracket.

The following image indicates the location of the 2230 solid-state drive that is installed in M.2 slot one and provides a visual

representation of the installation procedure.

Steps

1. Align the notch on the 2230 solid-state drive with the tab on the solid-state drive slot.

2. Slide the 2230 solid-state drive firmly into the solid-state drive slot at an angle.

3. Align the screw hole on the solid-state drive with the screw hole on the palm-rest and keyboard assembly.

4. Replace the screw (M2x3) that secures the 2230 solid-state drive to the palm-rest and keyboard assembly.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

Removing the 2280 solid-state drive from M.2 slot one

Prerequisites

1. Follow the procedure in Before working inside your computer.

NOTE: Solid-state drives are fragile. Exercise care when handling the solid-state drive.

NOTE: To avoid data loss, do not remove the solid-state drive while the computer is in sleep or on state.

26 Removing and installing components

2. Enter Service Mode.

3. Remove the base cover.

About this task

NOTE: Depending on the configuration ordered, your computer may support a 2280 solid-state drive, or a 2230 solid-state

drive in M.2 slot one.

NOTE: This procedure applies only to computers shipped with a 2280 solid-state drive installed in M.2 slot one.

The following image indicates the location of the 2280 solid-state drive that is installed in M.2 slot one and provides a visual

representation of the removal procedure.

Steps

1. Remove the screw (M2x3) that secures the solid-state drive to the palm-rest and keyboard assembly.

2. Slide and lift the 2280 solid-state drive off the M.2 solid-state drive slot one on the system board.

Installing the 2280 solid-state drive in M.2 slot one

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

NOTE: Solid-state drives are fragile. Exercise care when handling the solid-state drive.

NOTE: Depending on the configuration ordered, the computer one may support a 2280 solid-state drive, or a 2230

solid-state drive in M.2 slot one.

NOTE: This procedure is applicable if you are installing a 2280 solid-state drive in M.2 slot one.

NOTE: Before installing your 2230 or 2280 solid-state drive, ensure that the mounting bracket is in the correct location. For

more information, see Installing the solid-state drive mounting bracket.

Removing and installing components 27

The following image indicates the location of the 2280 solid-state drive that is installed in M.2 slot one and provides a visual

representation of the installation procedure.

Steps

1. Align the notch on the 2280 solid-state drive with the tab on the solid-state drive slot.

2. Slide the 2280 solid-state drive firmly into the solid-state drive slot at an angle.

3. Align the screw hole on the solid-state drive with the screw hole on the palm-rest and keyboard assembly.

4. Replace the screw (M2x3) that secures the 2280 solid-state drive to the palm-rest and keyboard assembly.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

Installing the solid-state drive mounting bracket on M.2 slot one

About this task

The following image provides a visual representation of the procedure to install the solid-state drive mounting bracket when

replacing M.2 2230 solid-state drive with M.2 2280 solid-state drive in M.2 slot one.

28 Removing and installing components

The following image provides a visual representation of the procedure to install the solid-state drive mounting bracket when

replacing M.2 2280 solid-state drive with M.2 2230 solid-state drive in M.2 slot one.

Steps

1. Slide and remove the solid-state drive mounting bracket from the mounting bracket slot on the palm-rest and keyboard

assembly.

2. Rotate the solid-state drive mounting bracket to 180 degrees.

3. Slide the solid-state mounting bracket into the mounting slot on the palm-rest and keyboard assembly.

4. Install the 2230 solid-state drive or 2280 solid-state drive, whichever applicable.

Solid-state drive—M.2 slot two

Removing the 2230 solid-state drive from M.2 slot two

Prerequisites

NOTE: M.2 slot two supports only 2230 solid-state drive.

Removing and installing components 29

NOTE: This procedure applies only to computers shipped with a 2230 solid-state drive installed in M.2 slot two.

1. Follow the procedure in Before working inside your computer.

NOTE: Solid-state drives are fragile. Exercise care when handling the solid-state drive.

NOTE: To avoid data loss, do not remove the solid-state drive while the computer is in sleep or on state.

2. Enter Service Mode.

3. Remove the base cover.

About this task

The following image indicates the location of the 2230 solid-state drive that is installed in M.2 slot two and provides a visual

representation of the removal procedure.

30 Removing and installing components

Steps

1. Remove the screw (M2x3) that secures the solid-state drive thermal shield and the solid-state drive to the palm-rest and

keyboard assembly.

2. Slide and lift the solid-state drive thermal shield off the solid-state drive.

3. Slide and remove the solid-state drive from the M.2 slot two.

Installing the 2230 solid-state drive in M.2 slot two

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

NOTE: Solid-state drives are fragile. Exercise care when handling the solid-state drive.

NOTE: M.2 slot two supports only 2230 solid-state drive.

NOTE: This procedure applies only to computers shipped with a 2230 solid-state drive installed in M.2 slot two.

The following image indicates the location of the 2230 solid-state drive that is installed in M.2 slot two and provides a visual

representation of the installation procedure.

Removing and installing components 31

Steps

1. Align the notch on the 2230 solid-state drive with the tab on M.2 slot two on the system board.

2. Slide the 2230 solid-state drive into M.2 slot two on the system board.

3. Place the solid-state drive thermal shield on the solid-state drive.

4. Align the screw hole on the solid-state drive thermal shield with the screw hole on the palm-rest and keyboard assembly.

5. Replace the screw (M2x3) that secures the solid-state drive thermal shield and solid-state drive to the palm-rest and

keyboard assembly.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

32 Removing and installing components

Wireless card

Removing the wireless card

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

About this task

The following images indicate the location of the wireless card and provide a visual representation of the removal procedure.

Steps

1. Remove the screw (M2x3) that secures the wireless-card bracket to the wireless card and system board.

2. Remove the wireless-card bracket from the wireless card.

3. Disconnect the antenna cables from the wireless card.

4. Slide and remove the wireless card from the wireless-card slot.

Removing and installing components 33

Installing the wireless card

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the wireless card and provides a visual representation of the installation procedure.

Steps

1. Connect the antenna cables to the wireless card.

The following table provides the antenna-cable color scheme for the wireless card that is supported by your computer.

Table 2. Antenna-cable color scheme

Connectors on the

wireless card

Antenna-cable color Silkscreen marking

Main White MAIN △ (white triangle)

Auxiliary Black AUX ▲ (black triangle)

34 Removing and installing components

2. Align the notch on the wireless card with the tab on the wireless-card slot on the system board.

3. Slide and insert the wireless card at an angle into the wireless-card slot on the system board.

4. Align the screw hole on the wireless-card bracket to the screw hole on the wireless card and system board.

5. Replace the screw (M2x3) that secures the wireless-card bracket to the wireless card and the system board.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

Fan

Removing the fan

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

About this task

The following images indicate the location of the fan and provide a visual representation of the removal procedure.

Steps

1. Disconnect the fan cable from the system board.

2. Remove the two (M2x3) screws that secure the fan to the palm-rest and keyboard assembly.

Removing and installing components 35

3. Lift the fan off the palm-rest and keyboard assembly.

Installing the fan

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the fan and provides a visual representation of the installation procedure.

Steps

1. Using the alignment posts, place the fan on the palm-rest and keyboard assembly.

2. Replace the two (M2x3) screws to secure the fan to the palm-rest and keyboard assembly.

3. Connect the fan cable to the system board.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

36 Removing and installing components

Coin-cell battery

Removing the coin-cell battery

Prerequisites

1. Follow the procedure in Before working inside your computer.

CAUTION: Removing the coin-cell battery resets the BIOS setup program’s settings to default. It is

recommended that you note the BIOS setup program’s settings before removing the coin-cell battery.

2. Enter Service Mode.

3. Remove the base cover.

About this task

The following images indicate the location of the coin-cell battery and provide a visual representation of the removal procedure.

Steps

1. Disconnect the coin-cell battery cable from the I/O board.

2. Using the flat-end of a plastic scribe, peel the coin-cell battery from the palm-rest and keyboard assembly.

Installing the coin-cell battery

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

Removing and installing components 37

About this task

The following image indicates the location of the coin-cell battery and provides a visual representation of the installation

procedure.

Steps

1. Adhere the coin-cell battery to the slot on the palm-rest and keyboard assembly.

2. Connect the coin-cell battery cable to the I/O board.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

Heat sink

Removing the heatsink

Prerequisites

1. Follow the procedure in Before working inside your computer.

CAUTION: For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The

oils in your skin can reduce the heat transfer capability of the thermal grease.

NOTE: The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you

touch it.

2. Enter Service Mode.

3. Remove the base cover.

38 Removing and installing components

About this task

The following images indicate the location of the heatsink and provide a visual representation of the removal procedure.

Steps

1. In reverse sequential order (as indicated on the heat sink), loosen the four captive screws that secure the heat sink to the

system board.

2. Lift the heat sink off the system board.

Installing the heatsink

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

CAUTION: Incorrect alignment of the heat sink can damage the system board and processor.

NOTE: If either the system board or the heat sink is replaced, use the thermal pad/paste provided in the kit to ensure that

thermal conductivity is achieved.

About this task

The following image indicates the location of the heatsink and provides a visual representation of the installation procedure.

Removing and installing components 39

Steps

1. Align the screw holes on the heat sink with the screw holes on the system board.

2. In sequential order (as indicated on the heat sink), tighten the four captive screws that secure the heat sink to the system

board.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

Network-port bracket

Removing the network-port bracket

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

About this task

The following image(s) indicate the location of the network-port bracket and provide a visual representation of the removal

procedure.

40 Removing and installing components

Steps

1. Remove the two (M2x5) screws that secure the network-port bracket to the I/O board.

2. Lift the network-port bracket off the I/O board.

Installing the network-port bracket

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following image(s) indicate the location of the network-port bracket and provide a visual representation of the installation

procedure.

Removing and installing components 41

Steps

1. Place the network-port bracket on the I/O board.

2. Align the screw holes on the network-port bracket to the screw holes on the I/O board.

3. Replace the two (M2x5) screws that secure the network-port bracket to the I/O board.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

I/O board

Removing the I/O board

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

4. Remove the network-port bracket.

About this task

The following images indicate the location of the I/O board and provide a visual representation of the removal procedure.

42 Removing and installing components

Steps

1. Remove the three (M2.5x4.5) screws that secure the left hinge to the palm-rest and keyboard assembly.

2. Open the display hinge at an angle of 90 degrees.

3. Open the latch, and disconnect the power button with optional fingerprint reader cable from the I/O board.

4. Disconnect the coin-cell battery cable from the I/O board.

5. Peel the tape that secures the I/O-board cable to the I/O board.

6. Open the latch and disconnect the I/O-board cable from the I/O board.

7. Remove the screw (M2x2) that secures the I/O board to the palm-rest and keyboard assembly.

8. Lift the I/O board off the palm-rest and keyboard assembly.

Installing the I/O board

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the I/O board and provides a visual representation of the installation procedure.

Removing and installing components 43

Steps

1. Slide the I/O board into the slots on the palm-rest and keyboard assembly.

2. Align the screw hole on the I/O board with the screw hole on the palm-rest and keyboard assembly.

3. Replace the screw (M2x2) that secures the I/O board to the palm-rest and keyboard assembly.

4. Connect the power-button with optional fingerprint reader cable into the connector on the I/O board and close the latch to

secure the cable.

5. Connect the coin-cell battery cable to the I/O board.

6. Connect the I/O-board cable to the I/O board and close the latch to secure the cable.

7. Adhere the tape that secures the I/O-board cable to the I/O board.

8. Close the left display hinge.

9. Replace the three (M2.5x4.5) screws that secure the left display hinge to the palm-rest and keyboard assembly.

Next steps

1. Install the network-port bracket.

2. Install the base cover.

3. Exit Service Mode.

4. Follow the procedure in After working inside your computer.

Speakers

Removing the speakers

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

44 Removing and installing components

About this task

The following images indicate the location of the speakers and provide a visual representation of the removal procedure.

Steps

1. Open the latch and disconnect the keyboard backlit cable, keyboard cable, and the touchpad cable from the system board.

2. Note the speaker cable routing, and remove the speaker cable from the routing guides on the palm-rest and keyboard

assembly.

3. Peel the tape that secures the speaker cable to the palm-rest and keyboard assembly.

4. Disconnect the speaker cable from the system board.

5. Lift the speakers, along with the cable, off the palm-rest and keyboard assembly.

Installing the speakers

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

Removing and installing components 45

About this task

The following image indicates the location of the speaker and provides a visual representation of the installation procedure.

Steps

1. Using the alignment posts and rubber grommets, place the speakers on the slots of the palm-rest and keyboard assembly.

2. Connect the speaker cable to the system board.

3. Route the speaker cable through the routing guides on the palm-rest and keyboard assembly.

4. Connect the keyboard backlit cable, keyboard cable, and the touchpad cable to its connectors on the system board and close

the latch to secure the cable.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

46 Removing and installing components

Touchpad

Removing the touchpad

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Remove the base cover.

3. Remove the battery.

About this task

The following images indicate the location of the touchpad and provide a visual representation of the removal procedure.

Steps

1. Open the latch and disconnect the touchpad cable from the system board.

2. Remove the three (M1.6x2) screws that secure the touchpad bracket to the palm-rest and keyboard assembly.

3. Peel the tape that secures the touchpad bracket to the palm-rest and keyboard assembly.

4. Lift the touchpad bracket off the palm-rest and keyboard assembly.

5. Remove the two (M2x1.8) screws that secure the touchpad to the palm-rest and keyboard assembly.

6. Peel the tapes that secure the touchpad to the palm-rest and keyboard assembly.

7. Lift the touchpad, along with the touchpad cable, off the palm-rest and keyboard assembly.

Installing the touchpad

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the touchpad and provides a visual representation of the installation procedure.

Removing and installing components 47

Steps

1. Slide the touchpad into the slot on the palm-rest and keyboard assembly.

NOTE: Turn the computer over and open the display. Ensure that the touchpad is equally aligned along all four sides.

2. Replace the two (M2x1.8) screws that secure the touchpad to the palm-rest and keyboard assembly.

3. Adhere the tapes that secure the touchpad to the palm-rest and keyboard assembly.

4. Align the screw holes on the touchpad bracket with the screw holes on the palm-rest and keyboard assembly.

5. Replace the three (M1.6x2) screws that secure the touchpad bracket to the palm-rest and keyboard assembly.

6. Adhere the tape that secures the touchpad bracket to the palm-rest and keyboard assembly.

7. Slide the touchpad cable into the connector on the touchpad and close the latch to secure the cable.

Next steps

1. Install the 3-cell battery or 4-cell battery, whichever applicable.

2. Install the base cover.

3. Follow the procedure in After working inside your computer.

48 Removing and installing components

Display assembly

Removing the display assembly

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

About this task

The following images indicate the location of the display assembly and provide a visual representation of the removal procedure.

Removing and installing components 49

Steps

1. Peel the tape that secures the display cable to the system board.

2. Open the latch and disconnect the display cable from the system board.

3. Remove the three (M2.5x4.5) screws that secure the left-display hinge to the system board.

4. Remove the three (M2.5x4.5) screws that secure the right-display hinge to the system board.

5. Open the display hinges at an angle of 90 degrees.

6. Gently slide the palm-rest and keyboard assembly off the display assembly.

Installing the display assembly

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the display assembly and provides a visual representation of the installation

procedure.

50 Removing and installing components

Steps

1. Slide the display assembly at an angle, and place the display assembly on the palm-rest and keyboard assembly.

2. Using the alignment posts, close the display hinges.

3. Replace the three (M2.5x4.5) screws that secure the right-display hinge to the system board.

4. Replace the three (M2.5x4.5) screws that secure the left-display hinge to the system board.

5. Slide the display cable into the connector on the system board and close the latch to secure the cable.

6. Adhere the tape that secures the display cable to the system board.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

Removing and installing components 51

Power button with optional fingerprint reader

Removing the power button with optional fingerprint reader

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

4. Remove the I/O board.

About this task

The following images indicate the location of the power-button with optional fingerprint reader and provide a visual

representation of the removal procedure.

Steps

1. Remove the screw (M2x3) that secures the power button with optional fingerprint reader to the palm-rest and keyboard

assembly.

2. Lift the power button with optional fingerprint reader off the palm-rest and keyboard assembly.

Installing the power button with optional fingerprint reader

About this task

The following images indicate the location of the power button with optional fingerprint reader and provide a visual

representation of the installation procedure.

52 Removing and installing components

Steps

1. Align and place the power button with optional fingerprint reader on the palm-rest and keyboard assembly.

2. Replace the screw (M2x3) that secures the power button with optional fingerprint reader to the palm-rest and keyboard

assembly.

Next steps

1. Install the I/O board.

2. Install the base cover.

3. Exit Service Mode.

4. Follow the procedure in After working inside your computer.

Power-adapter port

Removing the power-adapter port

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Enter Service Mode.

3. Remove the base cover.

About this task

The following images indicate the location of the power-adapter port and provide a visual representation of the removal

procedure.

Removing and installing components 53

Steps

1. Remove the three (M2.5x4.5) screws that secure the right display-hinge to the system board.

2. Open the display hinge at an angle of 90 degrees.

3. Disconnect the power-adapter port cable from the system board.

4. Peel the tape that secures the power-adapter port cable to the system board.

5. Remove the power-adapter port cable from the routing guide on the palm-rest and keyboard assembly.

6. Lift the power-adapter port, along with its cable, off the palm-rest and keyboard assembly.

Installing the power-adapter port

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the power-adapter port and provides a visual representation of the installation

procedure.

54 Removing and installing components

Steps

1. Place the power-adapter port, along with its cable, into the slot on the palm-rest and keyboard assembly.

2. Route the power-adapter port cable through the routing guide on the palm-rest and keyboard assembly.

3. Adhere the tape that secures the power-adapter port cable to the system board.

4. Connect the power-adapter port cable to the system board.

5. Close the right display-hinge and align the screw holes on the right display-hinge with the screw holes on the system board

and palm-rest and keyboard assembly.

6. Replace the three (M2.5x4.5) screws that secure the right display-hinge to the system board and palm-rest and keyboard

assembly.

Next steps

1. Install the base cover.

2. Exit Service Mode.

3. Follow the procedure in After working inside your computer.

System board

Removing the system board

Prerequisites

1. Follow the procedure in Before working inside your computer.

NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup

program after you replace the system board.

NOTE: Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup

program. You must make the appropriate changes again after you replace the system board.

NOTE: Before disconnecting the cables from the system board, note the location of the connectors so that you can

reconnect the cables correctly after you replace the system board.

2. Remove the base cover.

3. Remove the 3-cell battery or 4-cell battery, whichever applicable.

Removing and installing components 55

4. Remove the memory module.

5. Remove the M.2 2280 solid-state drive or M.2 2230 solid-state drive from M.2 slot one, whichever applicable.

6. Remove the M.2 2230 solid-state drive from M.2 slot two, if applicable.

7. Remove the wireless card.

8. Remove the fan.

9. Remove the heat sink.

About this task

NOTE: When removing the system board to replace/access other parts, the system board can be removed and installed

with the heat sink attached in order to simplify the procedure and preserve the thermal bond between the system board

and heat-sink.

The following image indicates the connectors on your system board.

Figure 1. System board connectors

1. Display cable connector

2. Power-adapter port cable connector

3. Keyboard backlit cable connector

4. Keyboard cable connector

5. Touchpad cable connector

6. Battery cable connector

7. Fan cable connector

8. Speaker cable connector

9. I/O-board cable connector

The following images indicate the location of the system board and provide a visual representation of the removal procedure.

56 Removing and installing components

Removing and installing components 57

Steps

1. Remove the three (M2.5x4.5) screws that secure the right display hinge to the palm-rest and keyboard assembly.

2. Open the right display hinge at an angle of 90 degrees.

3. Peel the tape that secures the display cable to the system board.

4. Open the latch and disconnect the display cable from the system board.

5. Peel the tape and disconnect the power-adapter port cable from the system board.

6. Remove the two (M2x4) screws that secure the USB Type-C bracket to the system board.

7. Open the latch, and disconnect the keyboard backlit cable from the system board.

8. Open the latch, and disconnect the keyboard cable from the system board.

9. Open the latch, and disconnect the touchpad cable from the system board.

10. Disconnect the speaker cable from the system board.

11. Peel the tape and disconnect the I/O-board cable from the system board.

12. Remove the three (M2x2) screws that secure the system board to the palm-rest and keyboard assembly.

13. Lift the system board off the palm-rest and keyboard assembly.

Installing the system board

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

NOTE: When replacing/accessing other parts, the system board can be installed with the heat sink attached in order to

simplify the procedure and preserve the thermal bond between the system board and heat-sink.

NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup

program after you replace the system board.

58 Removing and installing components

NOTE: Replacing the system board removes any changes you have made to the BIOS using the BIOS setup program. You

must make the appropriate changes again after you replace the system board.

The following image indicates the connectors on your system board.

Figure 2. System board connectors

1. Display cable connector

2. Power-adapter port cable connector

3. Keyboard backlit cable connector

4. Keyboard cable connector

5. Touchpad cable connector

6. Battery cable connector

7. Fan cable connector

8. Speaker cable connector

9. I/O-board cable connector

The following image indicates the location of the system board and provides a visual representation of the installation procedure.

Removing and installing components 59

60 Removing and installing components

Steps

1. Align and place the system board on the palm-rest and keyboard assembly.

2. Replace the three (M2x2) screws that secure the system board to the palm-rest and keyboard assembly.

3. Connect the display cable to the system board and close the latch to secure the cable.

4. Adhere the tape that secures the display cable to the system board.

5. Connect the power-adapter port cable to the system board.

6. Adhere the tape that secures the power-adapter port cable to the system board.

7. Align the screw holes on the USB Type-C port bracket with the screw holes on the system board.

8. Replace the two (M2x4) screws that secure the USB Type-C port bracket to the system board.

9. Connect the keyboard backlit cable to the system board and close the latch to secure the cable.

10. Connect the keyboard cable to the system board and close the latch to secure the cable.

11. Connect the touchpad cable to the system board and close the latch to secure the cable.

12. Connect the speaker cable to the system board.

Removing and installing components 61

13. Connect the I/O-board cable to the system board.

14. Adhere the tape that secures the I/O-board cable to the system board.

15. Close the right display hinge.

16. Replace the three (M2.5x4.5) screws that secure the right display-hinge to the palm-rest and keyboard assembly.

Next steps

1. Install the heat sink.

2. Install the fan.

3. Install the wireless card.

4. Install the M.2 2280 solid-state drive or M.2 2230 solid-state drive in M.2 slot one, whichever applicable.

5. Install the M.2 2230 solid-state drive in M.2 slot two, if applicable.

6. Install the memory module.

7. Install the 3-cell battery or 4-cell battery, whichever applicable.

8. Install the base cover.

9. Follow the procedure in After working inside your computer.

Palm-rest and keyboard assembly

Removing the palm-rest and keyboard assembly

Prerequisites

1. Follow the procedure in Before working inside your computer.

2. Remove the base cover.

3. Remove the 3-cell battery or 4-cell battery, whichever applicable.

4. Remove the memory module.

5. Remove the M.2 2280 solid-state drive or M.2 2230 solid-state drive from M.2 slot one, whichever applicable.

6. Remove the M.2 2230 solid-state drive from M.2 slot two, if applicable.

7. Remove the wireless card.

8. Remove the fan.

9. Remove the coin-cell battery.

10. Remove the I/O board.

11. Remove the system board.

NOTE: The system board can be removed along with the heat sink.

12. Remove the power-button with optional fingerprint reader.

13. Remove the power-adapter port.

14. Remove the speakers.

15. Remove the touchpad.

16. Remove the display assembly.

About this task

After performing the steps in the pre-requisites, you are left with the palm-rest and keyboard assembly.

62 Removing and installing components

Installing the palm-rest and keyboard assembly

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

Place the palm-rest and keyboard assembly on a flat surface.

Removing and installing components 63

Next steps

1. Install the display assembly.

2. Install the touchpad.

3. Install the speakers.

4. Install the power-adapter port.

5. Install the power-button with optional fingerprint reader.

6. Install the system board.

NOTE: The system board can be installed along with the heat sink.

7. Install the I/O board.

8. Install the fan.

9. Install the coin-cell battery.

10. Install the wireless card.

11. Install the M.2 2280 solid-state drive or M.2 2230 solid-state drive in M.2 slot one, whichever applicable.

12. Install the M.2 2230 solid-state drive in M.2 slot two, if applicable.

13. Install the memory module.

14. Install the 3-cell battery or 4-cell battery, whichever applicable.

15. Install the base cover.

16. Follow the procedure in After working inside your computer.

64 Removing and installing components

Drivers and downloads

This chapter details the supported operating systems along with instructions on how to install the drivers.

Topics:

•Downloading the drivers

Downloading the drivers

Steps

1. Turn on your computer.

2. Go to www.dell.com/support.

3. Enter the Service Tag of your computer, and then click Submit.

NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.

4. Click Drivers & downloads.

5. Click the Detect Drivers button.

6. Review and agree to the Terms and Conditions to use SupportAssist, then click Continue.

7. If necessary, your computer starts to download and install SupportAssist.

NOTE: Review on-screen instructions for browser-specific instructions.

8. Click View Drivers for My System.

9. Click Download and Install to download and install all driver updates detected for your computer.

10. Select a location to save the files.

11. If prompted, approve requests from User Account Control to make changes on the system.

12. The application installs all drivers and updates identified.

NOTE: Not all files can be installed automatically. Review the installation summary to identify if manual installation is

necessary.

13. For manual download and installation, click Category.

14. From the drop-down list, select the preferred driver.

15. Click Download to download the driver for your computer.

16. After the download is complete, navigate to the folder where you saved the driver file.

17. Double-click the driver file icon and follow the instructions on the screen to install the driver.

Drivers and downloads 65

System setup

CAUTION: Unless you are an expert computer user, do not change the settings in the BIOS Setup program.

Certain changes can make your computer work incorrectly.

NOTE: Before you change BIOS Setup program, it is recommended that you write down the BIOS Setup program screen

information for future reference.

Use the BIOS Setup program for the following purposes:

●Get information about the hardware installed in your computer, such as the amount of RAM and the size of the hard drive.

●Change the system configuration information.

●Set or change a user-selectable option, such as the user password, type of hard drive installed, and enabling or disabling

base devices.

Topics:

•BIOS overview

•Entering BIOS setup program

•Navigation keys

•Boot Sequence

•Advanced or Engineering configurations

•SupportAssist system resolution

•System setup options

•Updating the BIOS in Windows

•System and setup password

BIOS overview

The BIOS manages data flow between the computer's operating system and attached devices such as hard disk, video adapter,

keyboard, mouse, and printer.

Entering BIOS setup program

About this task

Turn on (or restart) your computer and press F2 immediately.

Navigation keys

NOTE: For most of the System Setup options, changes that you make are recorded but do not take effect until you restart

the system.

Keys Navigation

Up arrow Moves to the previous field.

Down arrow Moves to the next field.

Enter Selects a value in the selected field (if applicable) or follow the link in the field.

Spacebar Expands or collapses a drop-down list, if applicable.

Tab Moves to the next focus area.

66 System setup

Keys Navigation

Esc Moves to the previous page until you view the main screen. Pressing Esc in the main screen displays a

message that prompts you to save any unsaved changes and restarts the system.

Boot Sequence

Boot sequence enables you to bypass the System Setup–defined boot device order and boot directly to a specific device (for

example: optical drive or hard drive). During the Power-on Self-Test (POST), when the Dell logo appears, you can:

●Access System Setup by pressing F2 key

●Bring up the one-time boot menu by pressing F12 key.

The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot menu options

are:

●Windows Boot Manager

●UEFI HTTPs Boot

●UEFI RST BC711 NVMe SK hynix 256 GB DOBN6093129YBH26

●ONBOARD NIC (IPV4)

●ONBOARD NIC (IPV6)

The boot sequence screen also displays the option to access the System Setup screen.

Advanced or Engineering configurations

Table 3. Advanced or Engineering configurations

Option Description

ASPM ●Auto—Default

●L1 Only

●Disabled

●L0s and L1

●L0s Only

Pcie LinkSpeed ●Auto—Default

●Gen 1

●Gen 2

●Gen 3

SupportAssist system resolution

Table 4. SupportAssit System Resolution

Option Description

Auto OS Recovery

Threshold

The Auto OS Recovery Threshold setup option controls the automatic boot flow for Support

Assist System Resolution Console and Dell OS Recovery tool.

Choose one of the following options:

●OFF

●1

●2—Default

●3

SupportAssist OS

Recovery

Allows you to recover the SupportAssist OS Recovery (Disabled by default).

System setup 67

System setup options

NOTE: Depending on this computer and its installed devices, the items that are listed in this section may or may not be

displayed.

Table 5. System setup options—System information menu

Overview

BIOS Version Displays the BIOS version number.

Service Tag Displays the Service Tag of the computer.

Asset Tag Displays the Asset Tag of the computer.

Ownership Tag Displays the ownership tag of the computer.

Manufacture Date Displays the manufacture date of the computer.

Ownership Date Displays the ownership date of the computer.

Express Service Code Displays the express service code of the computer.

Ownership Tag Displays the ownership tag of the computer.

Signed Firmware Update Displays whether the signed firmware update is enabled.

Battery Displays the battery health information.

Primary Displays the primary battery.

Battery Level Displays the battery level.

Battery State Displays the battery state.

Health Displays the battery health.

AC Adapter Displays whether an AC adapter is installed.

Processor Information

Processor Type Displays the processor type.

Maximum Clock Speed Displays the maximum processor clock speed.

Core Count Displays the number of cores on the processor.

Processor L2 Cache Displays the processor L2 Cache size.

Processor ID Displays the processor identification code.

Processor L3 Cache Displays the processor L3 Cache size.

Current Clock Speed Displays the current processor clock speed.

Minimum Clock Speed Displays the minimum processor clock speed.

Microcode Version Displays the microcode version.

Intel Hyper-Threading Capable Displays whether the processor is Hyper-Threading (HT) capable.

64-Bit Technology Displays whether 64-bit technology is used.

Memory Information

Memory Installed Displays the total computer memory installed.

Memory Available Displays the total computer memory available.

Memory Speed Displays the memory speed.

Memory Channel Mode Displays single or dual channel mode.

Memory Technology Displays the technology that is used for the memory.

DIMM_SLOT 1 Displays capacity of the memory installed in the first DIMM slot.

DIMM_SLOT 2 Displays capacity of the memory installed in the second DIMM slot.

68 System setup

Table 5. System setup options—System information menu

Overview

Device Information

Panel Type Displays the Panel Type of the computer.

Video Controller Displays the graphics information of the computer.

Video Memory Displays the video memory information of the computer.

Video BIOS Version Displays the video BIOS version of the computer.

Native Resolution Native Resolution

Audio Controller Audio Controller

Wi-Fi Device Wi-Fi Device

Bluetooth Device Bluetooth Device

LOM Mac Address Displays the unique MAC address for the computer

Table 6. System setup options—Boot Configuration menu

Boot options

Boot Sequence

Boot Mode: UEFI only Displays the boot mode of this computer.

Boot Sequence Displays the boot sequence.

Secure Boot

Enable Secure Boot Ensures the system boots using only to validated boot software.

Secure Boot Mode Changes to Secure Boot operation mode modifies the behavior of the Secure

Boot to allow evaluation of UEFI driver signatures.

●Deployed Mode - Default: ON

●Audit Mode - Default: OFF

Expert Key Management

Enable Custom Mode Enables or disables the PK, KEK, db and dbx security key databases to be

manipulated.

Default: OFF.

Custom Mode Key Management Default: OFF.

Advanced Boot Options

Enable UEFI Network Stack Enables or disables UEFI Network Stack.

Default: PK

Table 7. System setup options—Integrated Devices menu (continued)

System Configuration

Date/Time

Date Sets the computer date in MM/DD/YYYY format. Changes to the date take

effect immediately.

Time Sets the computer time in HH/MM/SS 24-hour format. You can switch

between 12-hour and 24-hour clock. Changes to the time take effect

immediately.

Camera Enables or disables the camera

Enable Camera Default: ON.

Enable Audio Enables or disables all integrated audio controller.

System setup 69

Table 7. System setup options—Integrated Devices menu

System Configuration

Default: ON.

Enable Microphone Enables or disables microphone.

Default: ON.

Enable Internal Speaker Enables or disables internal speaker.

Default: ON.

USB Configuration

Enable External USB Ports Enables or disables USB ports to be functional in an operating system

environment.

Default: ON.

Enable USB Boot Support Enables or disables booting from USB mass storage devices such as external

hard drive, optical drive, and USB drive.

Default: ON.

Disable USB4 PCIE Tunneling Enables or disables the USB4 PCIE tunneling.

Default: OFF.

Video/Power only on Type-C Ports Limits Type-C port functionality to video or power only.

Default: OFF.

SATA Operation Configures operating mode of the integrated SATA hard drive controller.

Default: RAID. SATA is configured to support RAID (Intel Rapid Restore

Technology).

Drives Enables or disables various onboard drives.

M.2 PCIe SSD-0/SATA-2 Default: ON.

SATA-0 Default: ON.

Drive Information Displays the information of various onboard drives.

Miscellaneous Devices Enables or disables various onboard devices.

Enable Camera Enables or disables the camera.

Default: ON.

Keyboard Illumination Configures the operating mode of the keyboard illumination feature.

Default: Disabled. The keyboard illumination will always be off.

Keyboard Backlight Timeout on AC Configures the timeout value for the keyboard when an AC adapter is

connected to the computer. The keyboard backlight timeout value is only

effect when the backlight is enabled.

Default: 10 seconds.

Keyboard Backlight Timeout on Battery Configures the timeout value for the keyboard when the computer is running

on battery. The keyboard backlight timeout value is only effect when the

backlight is enabled.

Default: 10 seconds.

Touchscreen Enables or disables the touchscreen for the operating system.

NOTE: Touchscreen will always work in the BIOS setup irrespective of this

setting.

Default: ON.

70 System setup

Table 8. System setup options—Storage menu

Storage

Storage Interface

Port Enablement Enables or disables onboard drives

Default: ON.

SMART Reporting

Enable SMART Reporting Enables or disables the S.M.A.R.T(Self-Monitoring, Analysis, and Reporting

Technology) option on the system.

Default: OFF.

Drive Information

M.2 PCIe SSD-1 Provides information about the type and device on the computer.

Table 9. System setup options—Display menu

Storage

Display Brightness

Brightness on battery power Sets the screen brightness when the computer is running on battery power.

Brightness on AC power Sets the screen brightness when the computer is running on AC power.

EcoPower Enables or disables EcoPower which increases the battery life by reducing the

screen brightness when appropriate.

Default: ON.

Full-Screen Logo Displays full screen logo if the image matches screen resolution.

Default: OFF.

Table 10. System setup options—Connection menu

Connection

Network Controller Configuration

Integrated NIC Allows pre-OS and early OS networking features to use any enabled NICs.

Enabled with PXE: Default

Wireless Device Enable Enable or disable internal WLAN/Bluetooth devices.

WLAN Default: ON.

Bluetooth Default: ON.

Enable UEFI Network Stack Allows pre-OS and early OS networking features to use any enabled NICs. This

may be used without the PXE turned on.

Default: ON.

HTTP(s) Boot Feature

HTTP(s) Boot This platform has HTTP(s) Boot capabilities.

Default: ON.

NOTE: Provisioning of the Certificate is necessary to connect to HTTPs

Boot server.

Table 11. System setup options—Power Management menu

System setup 71

Table 11. System setup options—Power Management menu

Power Management

Battery Configuration Enables the computer to run on battery during peak power usage hours. Use

the below options to prevent AC power usage between certain times of each

day.

Default: Adaptive. Battery settings are adaptively optimized based on your

typical battery usage pattern.

Enable Advanced Battery Charge

Configuration

Enables Advanced Battery Charge Configuration from the beginning of the

day to a specified work period. Advanced Battery Charged maximizes battery

health while still supporting heavy use during the work day.

Default: OFF.

Enable Peak Shift Enables the system to run on battery during peak power usage hours.

Default: OFF.

Thermal Management Allows for cooling fan and processor heat management to adjust system

performance, noise, and temperature.

Default: Optimized.

Enable USB Wake Support Enables the USB devices to wake the computer from Standby mode, Hibernate

and Power Off.

Default: OFF.

Enable on Dell USB-C Dock Enables the Dell USB-C Dock when connected to wake the computer from

Standby mode, Hibernate and Power Off.

Default: ON.

Block Sleep Blocks the computer from entering Sleep (S3) mode in the operating system.

Default: OFF.

NOTE: If enabled, the computer will not go to sleep, Intel Rapid Start will

be disabled automatically, and the operating system power option will be

blank if it was set to Sleep.

Lid Switch

Enable Lid Switch Enables or disables lid switch.

Default: ON.

Power On Lid Open Enables the computer to power up from the off state whenever the lid is

opened.

Default: ON.

Intel Speed Shift Technology Enables or disables Intel Speed Shift Technology support which enables

the operating system to select the appropriate processor performance

automatically.

Default: ON.

Table 12. System setup options—Security menu (continued)

Security

TPM 2.0 Security

TPM 2.0 Security On Enable or disable TPM 2.0 security options.

By default, the TPM 2.0 Security On option is enabled.

PPI Bypass for Enable Commands Allows the OS to skip BIOS PPI user prompts when issuing TPM PPI enable

and activate commands.

72 System setup

Table 12. System setup options—Security menu

Security

By default, the PPI Bypass for Enable Commands option is disabled.

PPI Bypass for Disable Commands Allows the OS to skip BIOS PPI user prompts when issuing TPM PPI disable

and deactivate commands.

By default, the PPI Bypass for Disable Commands option is disabled.

Attestation Enable Enables to control whether the Trusted Platform Module (TPM) Endorsement

Hierarchy is available to the operating system.

By default, the Attestation Enable option is enabled.

Key Storage Enable Enables to control whether the Trusted Platform Module (TPM) Storage

Hierarchy is available to the operating system.

By default, the Key Storage Enable option is enabled.

SHA-256 BIOS and the TPM will use the SHA-256 hash algorithm to extend

measurements into the TPM PCRs during BIOS boot.

By default, the SHA-256 option is enabled.

Clear Enables to clear the TPM owner information and returns the TPM to the

default state.

By default, the Clear option is disabled.

PPI ByPass for Clear Commands Controls the TPM Physical Presence Interface (PPI).

By default, the PPI ByPass for clear Commands option is disabled.

TPM State Enables or disables the TPM. this is the normal operating state for the TPM

when you want to use its complete arrays of capabilities.

By default, the TPM State option is enabled.

SMM Security Mitigation Enable or disable SMM Security Mitigation.

By default, the option is enabled.

Data Wipe on Next Boot

Start Data Wipe Enable or disable the data wipe on next boot.

By default, the option is enabled.

Absolute Enable or disable or permanently disable the BIOS module interface of the

optional Absolute Persistence Module service from Absolute software.

By default, the option is enabled.

UEFI Boot Path Security Controls whether or not the computer will prompt the user to enter the admin

password (if set) when booting to a UEFI boot device from the F12 boot menu.

By default, the Always Except Internal HDD option is enabled.

Table 13. System setup options—Passwords menu

Passwords

Admin Password Set, change, or delete the administrator password.

System Password Set, change, or delete the computer password.

NVMe SSD0 Set, change, or delete the NVMe SSD0 password.

Password Configuration

Upper Case Letter Reinforces password must have at least one upper case letter.

By default, the option is disabled.

System setup 73

Table 13. System setup options—Passwords menu

Passwords

Lower Case Letter Reinforces password must have at least one lower case letter.

By default, the option is disabled.

Digit Reinforces password must have at least one digit.

By default, the option is disabled.

Special Character Reinforces password must have at least one special character.

By default, the option is disabled.

Minimum Characters Set the minimum characters allowed for password.

Password Bypass When enabled, this always prompts for computer and internal hard drive

passwords when powered on from the off state.

By default, the Disabled option is enabled.

Password Changes

Enable Non-Admin Password Changes Enable or disable to change computer and hard drive password without the

need for admin password.

By default, the option is enabled.

Admin Setup Lockout

Enable Admin Setup Lockout Enables administrators control over how their users can or cannot access BIOS

setup.

By default, the option is disabled.

Master Password Lockout

Enable Master Password Lockout When enabled, this will disable the master password support.

By default, the option is disabled.

Allow Non-Admin PSID Revert

Enable Allow Non-Admin PSID Revert Controls access to the Physical Security ID (PSID) revert of NVMe hard-drives

from the Dell Security Manager prompt.

By default, the option is disabled.

Table 14. System setup options—Update, Recovery menu

Update, Recovery

UEFI Capsule Firmware Updates Enable or disable BIOS updates through UEFI capsule update packages.

By default, the option is enabled.

BIOS Recovery from Hard Drive Enables the user to recover from certain corrupted BIOS conditions from a

recovery file on the user primary hard drive or an external USB key.

By default, the option is enabled.

BIOS Downgrade

Allow BIOS Downgrade Enable or disable the flashing of the computer firmware to previous revision is

blocked.

By default, the option is enabled.

SupportAssist OS Recovery Enable or disable the boot flow for SupportAssist OS Recovery tool in the

event of certain computer errors.

By default, the option is enabled.

74 System setup

Table 14. System setup options—Update, Recovery menu

Update, Recovery

BIOSConnect Enable or disable cloud Service OS recovery if the main operating system fails

to boot with the number of failures equal to or greater than the value specified

by the Auto OS Recovery Threshold setup option and local Service OS does not

boot or is not installed.

By default, the option is enabled.

Dell Auto OS Recovery Threshold Controls the automatic boot flow for SupportAssist System Resolution Console

and for Dell OS Recovery Tool.

By default, the threshold value is set to 2.

Table 15. System setup options—System Management menu

System Management

Service Tag Displays the Service Tag of the computer.

Asset Tag Create a computer Asset Tag.

AC Behavior

Wake on AC Enable or disable the wake on AC option.

By default, the option is disabled.

Auto on Time Enable to set the computer to turn on automatically every day or on a

preselected date and time. This option can be configured only if the Auto On

Time is set to Everyday, Weekdays, or Selected Days.

By default, the option is disabled.

Table 16. System setup options—Keyboard menu

Keyboard

Numlock Enable Enable or disable the Numlock function when the computer boots.

By default, the option is enabled.

Fn Lock Options By default, the Fn lock option is enabled.

Lock Mode ●Lock Mode Standard - Traditional F1-F12 functions

●Lock Mode Secondary - Enables secondary functions on the Fn keys.

Table 17. System setup options—Pre-boot Behavior menu

Pre-boot Behavior

Adapter Warnings

Enable Adapter Warnings Enable or disable the warning messages during boot when the adapters with

less power capacity are detected.

By default, the option is enabled.

Warnings and Errors Enable or disable the action to be done when a warning or error is encountered.

By default, the Prompt on Warnings and Errors option is enabled.

USB-C Warnings Enable or disable dock warning messages.

By default, the Enable Dock Warning Messages option is enabled.

Fastboot Enable to set the speed of the boot process.

By default, the Thorough option is enabled.

Extend BIOS POST Time Set the BIOS POST time.

By default, the 0 seconds option is enabled.

System setup 75

Table 18. System setup options—Virtualization menu

Virtualization

Intel Virtualization Technology

Enable Intel Virtualization Technology

(VT)

Specify whether a Virtual Machine Monitor (VMM) can utilize the additional

hardware capabilities provided by Intel Virtualization Technology.

By default, the option is enabled.

VT for Direct I/O Specify whether a Virtual Machine Monitor (VMM) can utilize the additional

hardware capabilities provided by Intel Virtualization Technology for Direct I/O.

By default, the option is enabled.

Table 19. System setup options—Performance menu

Performance

Multi Core Support

Active Cores Enables to change the number of CPU cores available to the operating system.

By default, the All Cores options is enabled.

Intel SpeedStep

Enable Intel SpeedStep Technology Enables the computer to dynamically adjust processor voltage and core

frequency, decreasing average power consumption and heat production.

By default, the option is enabled.

C-States Control

Enable C-State Control Enable or disable additional processor sleep states.

By default, the option is enabled.

Intel Turbo Boost Technology

Enable Intel Turbo Boost Technology Enable or disable Intel TurboBoost mode of the processor.

By default, the option is enabled.

Intel Hyper-Threading Technology

Enable Intel Hyper-Threading Technology Enable or disable Hyper-Threading in the processor.

By default, the option is enabled.

Table 20. System setup options—System Logs menu

System Logs

BIOS Event Log

Clear Bios Event Log Display BIOS events.

By default, the Keep Log option is enabled.

Thermal Event Log

Clear Thermal Event Log Display Thermal events.

By default, the Keep Log option is enabled.

Power Event Log

Clear Power Event Log Display power events.

By default, the Keep Log option is enabled.

License Information Displays the license information of the computer.

76 System setup

Updating the BIOS in Windows

Prerequisites

It is recommended to update your BIOS (System Setup) when you replace the system board or if an update is available. For

laptops, ensure that your computer battery is fully charged and connected to a power before initiating a BIOS update.

About this task

NOTE: If BitLocker is enabled, it must be suspended prior to updating the system BIOS, and then re enabled after the BIOS

update is completed.

For more information about this subject, see Knowledge Article: How to Enable or Disable BitLocker with TPM in Windows.

Steps

1. Restart the computer.

2. Go to Dell.com/support.

●Enter the Service Tag or Express Service Code and click Submit.

●Click Detect Product and follow the instructions on screen.

3. If you are unable to detect or find the Service Tag, click Choose from all products.

4. Choose the Products category from the list.

NOTE: Choose the appropriate category to reach the product page.

5. Select your computer model and the Product Support page of your computer appears.

6. Click Get drivers and click Drivers and Downloads.

The Drivers and Downloads section opens.

7. Click Find it myself.

8. Click BIOS to view the BIOS versions.

9. Identify the latest BIOS file and click Download.

10. Select your preferred download method in the Please select your download method below window, click Download File.

The File Download window appears.

11. Click Save to save the file on your computer.

12. Click Run to install the updated BIOS settings on your computer.

Follow the instructions on the screen.

Updating BIOS on systems with BitLocker enabled

CAUTION: If BitLocker is not suspended before updating the BIOS, the next time you reboot the system it

will not recognize the BitLocker key. You will then be prompted to enter the recovery key to progress and

the system will ask for this on each reboot. If the recovery key is not known, this can result in data loss or

an unnecessary operating system reinstall. For more information about this subject, see Knowledge Article:

Updating the BIOS on Dell Systems With BitLocker Enabled

Updating the Dell BIOS in Linux and Ubuntu environments

If you want to update the system BIOS in a Linux environment, such as Ubuntu, see Update the Dell BIOS in a Linux or Ubuntu

environment.

Flashing BIOS (USB key)

Steps

1. Follow the procedure from step 1 to step 7 in "Flashing the BIOS" to download the latest BIOS setup program file.

System setup 77

2. Create a bootable USB drive. For more information see the knowledge base article SLN143196 at www.dell.com/support.

3. Copy the BIOS setup program file to the bootable USB drive.

4. Connect the bootable USB drive to the computer that needs the BIOS update.

5. Restart the computer and press F12 when the Dell logo is displayed on the screen.

6. Boot to the USB drive from the One Time Boot Menu.

7. Type the BIOS setup program filename and press Enter.

8. The BIOS Update Utility appears. Follow the instructions on the screen to complete the BIOS update.

System and setup password

Table 21. System and setup password

Password type Description

System password Password that you must enter to log on to your system.

Setup password Password that you must enter to access and make changes to

the BIOS settings of your computer.

You can create a system password and a setup password to secure your computer.

CAUTION: The password features provide a basic level of security for the data on your computer.

CAUTION: Anyone can access the data stored on your computer if it is not locked and left unattended.

NOTE: System and setup password feature is disabled.

Assigning a system setup password

Prerequisites

You can assign a new System or Admin Password only when the status is in Not Set.

About this task

To enter the system setup, press F2 immediately after a power-on or reboot.

Steps

1. In the System BIOS or System Setup screen, select Security and press Enter.

The Security screen is displayed.

2. Select System/Admin Password and create a password in the Enter the new password field.

Use the following guidelines to assign the system password:

●A password can have up to 32 characters.

●The password can contain the numbers 0 through 9.

●Only lower case letters are valid, upper case letters are not allowed.

●Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

3. Type the system password that you entered earlier in the Confirm new password field and click OK.

4. Press Esc and a message prompts you to save the changes.

5. Press Y to save the changes.

The computer reboots.

78 System setup

Deleting or changing an existing system setup password

Prerequisites

Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing

System and Setup password. You cannot delete or change an existing System or Setup password, if the Password Status is

Locked.

About this task

To enter the System Setup, press F2 immediately after a power-on or reboot.

Steps

1. In the System BIOS or System Setup screen, select System Security and press Enter.

The System Security screen is displayed.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password, alter or delete the existing system password and press Enter or Tab.

4. Select Setup Password, alter or delete the existing setup password and press Enter or Tab.

NOTE: If you change the System and/or Setup password, re enter the new password when prompted. If you delete the

System and Setup password, confirm the deletion when prompted.

5. Press Esc and a message prompts you to save the changes.

6. Press Y to save the changes and exit from System Setup.

The computer restarts.

System setup 79

Troubleshooting

Topics:

•Dell SupportAssist Pre-boot System Performance Check diagnostics

•System diagnostic lights

•Recovering the operating system

•Flashing BIOS (USB key)

•Flashing the BIOS

•WiFi power cycle

•Flea power release

Dell SupportAssist Pre-boot System Performance

Check diagnostics

About this task

SupportAssist diagnostics (also known as system diagnostics) performs a complete check of your hardware. The Dell

SupportAssist Pre-boot System Performance Check diagnostics is embedded with the BIOS and is launched by the BIOS

internally. The embedded system diagnostics provides a set of options for particular devices or device groups allowing you to:

●Run tests automatically or in an interactive mode

●Repeat tests

●Display or save test results

●Run thorough tests to introduce additional test options to provide extra information about the failed device(s)

●View status messages that inform you if tests are completed successfully

●View error messages that inform you of problems encountered during testing

NOTE: Some tests for specific devices require user interaction. Always ensure that you are present at the computer

terminal when the diagnostic tests are performed.

For more information, see Resolve Hardware Issues With Built-in and Online Diagnostics (SupportAssist ePSA, ePSA or PSA

Error Codes) .

Running the SupportAssist Pre-Boot System Performance Check

Steps

1. Turn on your computer.

2. As the computer boots, press the F12 key as the Dell logo appears.

3. On the boot menu screen, select the Diagnostics option.

4. Click the arrow at the bottom left corner.

Diagnostics front page is displayed.

5. Click the arrow in the lower-right corner to go to the page listing.

The items detected are listed.

6. To run a diagnostic test on a specific device, press Esc and click Yes to stop the diagnostic test.

7. Select the device from the left pane and click Run Tests.

8. If there are any issues, error codes are displayed.

Note the error code and validation number and contact Dell.

80 Troubleshooting

System diagnostic lights

Battery-status light

Indicates the power and battery-charge status.

Solid white — Power adapter is connected and the battery has more than 5 percent charge.

Amber — Computer is running on battery and the battery has less than 5 percent charge.

Off

●Power adapter is connected and the battery is fully charged.

●Computer is running on battery and the battery has more than 5 percent charge.

●Computer is in sleep state, hibernation, or turned off.

The power and battery-status light blinks amber along with beep codes indicating failures.

For example, the power and battery-status light blinks amber two times followed by a pause, and then blinks white three times

followed by a pause. This 2,3 pattern continues until the computer is turned off indicating no memory or RAM is detected.

The following table shows different power and battery-status light patterns and associated problems.

Blinking Pattern Problem description Suggested resolution

1 1 TPM detection failure Replace the system board.

1 2 Unrecoverable SPI flash

failure

Replace the system board.

1 5 EC unable to program i-Fuse Replace the system board.

1 6 Generic catch-all for

ungraceful EC code flow

errors

Disconnect all power source

(AC, battery, coin cell) and

drain flea power by pressing &

holding down power button.

2 1 CPU failure Run the Intel CPU diagnostics

tools. If problem persists,

replace the system board.

2 2 System Board failure

(included BIOS corruption or

ROM error)

Flash latest BIOS version. If

problem persists, replace the

system board.

2 3 No Memory / RAM detected Confirm that the memory

module is installed properly. If

problem persists, replace the

memory module.

2 4 Memory / RAM failure Reset and swap memory

modules amongst the slots. If

problem persists, replace the

memory module.

2 5 Invalid memory installed Reset and swap memory

modules amongst the slots. If

problem persists, replace the

memory module.

2 6 System board / Chipset Error Replace the system board.

2 7 LCD failure (SBIOS message) Replace the LCD module.

2 8 LCD failure (EC detection of

power rail failure)

Replace the system board.

3 1 CMOS battery failure Reset the CMOS battery

connection. If problem

persists, replace the RTC

battery.

Troubleshooting 81

Blinking Pattern Problem description Suggested resolution

3 2 PCI or Video card/chip failure Replace the system board.

3 3 BIOS recovery image not

found

Flash latest BIOS version. If

problem persists, replace the

system board.

3 4 BIOS recovery image found

but invalid

Flash latest BIOS version. If

problem persists, replace the

system board.

3 5 Power rail failure Replace the system board.

3 6 Flash corruption detected by

SBIOS.

Replace the system board.

3 7 Timeout waiting on ME to

reply to HECI message.

Replace the system board.

Camera status light: Indicates whether the camera is in use.

●Solid white — Camera is in use.

●Off — Camera is not in use.

Caps Lock status light: Indicates whether Caps Lock is enabled or disabled.

●Solid white — Caps Lock enabled.

●Off — Caps Lock disabled.

Recovering the operating system

When your computer is unable to boot to the operating system even after repeated attempts, it automatically starts Dell

SupportAssist OS Recovery.

Dell SupportAssist OS Recovery is a standalone tool that is preinstalled in all Dell computers installed with Windows 10 operating

system. It consists of tools to diagnose and troubleshoot issues that may occur before your computer boots to the operating

system. It enables you to diagnose hardware issues, repair your computer, back up your files, or restore your computer to its

factory state.

You can also download it from the Dell Support website to troubleshoot and fix your computer when it fails to boot into their

primary operating system due to software or hardware failures.

For more information about the Dell SupportAssist OS Recovery, see Dell SupportAssist OS Recovery User's Guide at

www.dell.com/support.

Flashing BIOS (USB key)

Steps

1. Follow the procedure from step 1 to step 7 in "Flashing the BIOS" to download the latest BIOS setup program file.

2. Create a bootable USB drive. For more information see the knowledge base article SLN143196 at www.dell.com/support.

3. Copy the BIOS setup program file to the bootable USB drive.

4. Connect the bootable USB drive to the computer that needs the BIOS update.

5. Restart the computer and press F12 when the Dell logo is displayed on the screen.

6. Boot to the USB drive from the One Time Boot Menu.

7. Type the BIOS setup program filename and press Enter.

8. The BIOS Update Utility appears. Follow the instructions on the screen to complete the BIOS update.

82 Troubleshooting

Flashing the BIOS

About this task

You may need to flash (update) the BIOS when an update is available or when you replace the system board.

Follow these steps to flash the BIOS:

Steps

1. Turn on your computer.

2. Go to www.dell.com/support.

3. Click Product support, enter the Service Tag of your computer, and then click Submit.

NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.

4. Click Drivers & downloads > Find it myself.

5. Select the operating system installed on your computer.

6. Scroll down the page and expand BIOS.

7. Click Download to download the latest version of the BIOS for your computer.

8. After the download is complete, navigate to the folder where you saved the BIOS update file.

9. Double-click the BIOS update file icon and follow the instructions on the screen.

WiFi power cycle

About this task

If your computer is unable to access the internet due to WiFi connectivity issues a WiFi power cycle procedure may be

performed. The following procedure provides the instructions on how to conduct a WiFi power cycle:

NOTE: Some ISPs (Internet Service Providers) provide a modem/router combo device.

Steps

1. Turn off your computer.

2. Turn off the modem.

3. Turn off the wireless router.

4. Wait for 30 seconds.

5. Turn on the wireless router.

6. Turn on the modem.

7. Turn on your computer.

Flea power release

About this task

Flea power is the residual static electricity that remains on the computer even after it has been powered off and the battery has

been removed. The following procedure provides the instructions on how to conduct flea power release:

Steps

1. Turn off your computer.

2. Disconnect the power adapter from your computer.

3. Press and hold the power button for 15 seconds to drain the flea power.

4. Connect the power adapter to your computer.

5. Turn on your computer.

Troubleshooting 83

Getting help

Topics:

•Contacting Dell

Contacting Dell

Prerequisites

NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing

slip, bill, or Dell product catalog.

About this task

Dell provides several online and telephone-based support and service options. Availability varies by country and product, and

some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues:

Steps

1. Go to Dell.com/support.

2. Select your support category.

3. Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.

4. Select the appropriate service or support link based on your need.

84 Getting help

Table of Contents

DELL 5510 User Manual

Related Manuals