Dell Precision 5520 Owner's Manual
Working on your computer
Removing and installing components
Diagnostics
- Enhanced Pre-Boot System Assessment (ePSA) diagnostics
- Device Status Light
System Setup Options
Technical Specifications
Contacting Dell

DELL 5520 User Manual

Displayed below is the user manual for 5520 by DELL which is a product in the Notebooks category. This manual has pages.

Related Manuals

DELL 5520 Manual

Dell Precision 5520

Owner's Manual

Regulatory Model: P56F

Regulatory Type: P56F001

GUID-5B8DE7B7-879F-45A4-88E0-732155904029

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

GUID-089FFA4B-3A62-4B51-BDE1-309C58A451D9

trademarks may be trademarks of their respective owners.

2017 - 01

Rev. A00

Contents

1 Working on your computer............................................................................................................................. 5

Turning o Your Computer................................................................................................................................................5

Using power buttonUsing charms..............................................................................................................................5

Before working inside your computer..............................................................................................................................5

After working inside your computer.................................................................................................................................6

2 Removing and installing components............................................................................................................. 7

Recommended Tools..........................................................................................................................................................7

Base cover...........................................................................................................................................................................7

Removing the Base Cover...........................................................................................................................................7

Installing the Base Cover.............................................................................................................................................8

Battery.................................................................................................................................................................................8

Removing the Battery..................................................................................................................................................8

Installing the Battery....................................................................................................................................................9

PCIe Solid State Drive (SSD)............................................................................................................................................9

Removing the Solid State Drive (SSD)......................................................................................................................9

Installing the solid-state drive....................................................................................................................................10

Hard drive.......................................................................................................................................................................... 10

Removing the Hard Drive.......................................................................................................................................... 10

Installing the Hard Drive.............................................................................................................................................12

Speaker.............................................................................................................................................................................. 12

Removing the Speakers ............................................................................................................................................12

Installing the Speakers............................................................................................................................................... 13

Coin cell battery................................................................................................................................................................ 13

Removing the Coin-Cell Battery............................................................................................................................... 13

Installing the Coin-Cell Battery..................................................................................................................................14

Keyboard............................................................................................................................................................................15

Removing the Keyboard.............................................................................................................................................15

Installing the Keyboard............................................................................................................................................... 16

WLAN card........................................................................................................................................................................ 17

Removing the WLAN Card........................................................................................................................................ 17

Installing the WLAN Card.......................................................................................................................................... 18

Memory module................................................................................................................................................................ 18

Removing the Memory Module(s)............................................................................................................................18

Installing the Memory Module(s)..............................................................................................................................19

System fan.........................................................................................................................................................................19

Removing the Fans ....................................................................................................................................................19

Installing the Fans...................................................................................................................................................... 20

Heat sink............................................................................................................................................................................ 21

Removing the Heatsink..............................................................................................................................................21

Installing the Heatsink................................................................................................................................................22

Power connector port..................................................................................................................................................... 22

Removing the DC-in Connector...............................................................................................................................22

Contents 3

Installing the DC-in Adapter Port............................................................................................................................. 23

Display Assembly..............................................................................................................................................................23

Removing the Display Assembly...............................................................................................................................23

Installing the Display Assembly.................................................................................................................................25

System board....................................................................................................................................................................25

Removing the System Board....................................................................................................................................25

Installing the System Board.......................................................................................................................................27

Palm rest........................................................................................................................................................................... 27

Removing the Palmrest Assembly............................................................................................................................27

Installing the Palmrest Assembly..............................................................................................................................28

3 Diagnostics.................................................................................................................................................. 29

Enhanced Pre-Boot System Assessment (ePSA) diagnostics...................................................................................29

Device Status Light......................................................................................................................................................... 29

4 System Setup Options.................................................................................................................................30

5 Technical Specications.............................................................................................................................. 35

6 Contacting Dell.............................................................................................................................................41

4Contents

GUID-9CCD6D90-C1D1-427F-9E77-D4F83F3AD2B6

Working on your computer

GUID-C562EBB9-042F-4E85-81D4-6873FD15CCE1

Turning o Your Computer

CAUTION: To avoid losing data, save and close all open les and exit all open programs before you turn o your

computer.

You can turn o your computer in two ways :

1 Using the power button

2 Using the charms menu

Using power button

1 Press and hold the Power button to turn o the screen.

Using charms

1 Swipe from the right edge of the display to access the Charms menu.

2 Touch Settings —> Power —> Shut down to turn o the computer.

GUID-82258B8D-DC8F-4D55-97C8-3CEC2FB560A4

Before working inside your computer

1 Ensure that your work surface is at and clean to prevent the computer cover from being scratched.

2 Turn o your computer.

3 If the computer is connected to a docking device (docked), undock it.

4 Disconnect all network cables from the computer (if available).

CAUTION: If your computer has an RJ45 port, disconnect the network cable by rst unplugging the cable from your

computer.

5 Disconnect your computer and all attached devices from their electrical outlets.

6 Open the display.

7 Press and hold the power button for few seconds, to ground the system board.

CAUTION: To guard against electrical shock unplug your computer from the electrical outlet before performing Step #

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching

an unpainted metal surface at the same time as touching a connector on the back of the computer.

8 Remove any installed ExpressCards or Smart Cards from the appropriate slots.

Working on your computer 5

GUID-5A244B18-624F-44B5-868E-E4400DA24DEE

After working inside your computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your

computer.

CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries

designed for other Dell computers.

1 Connect any external devices, such as a port replicator, battery slice, or media base, and replace any cards, such as an ExpressCard.

2 Connect any telephone or network cables to your computer.

CAUTION: To connect a network cable, rst plug the cable into the network device and then plug it into the

computer.

3 Replace the battery.

4 Connect your computer and all attached devices to their electrical outlets.

5 Turn on your computer.

6 Working on your computer

GUID-7AAAE6E7-9D06-4C20-82BF-728ABC2DF3EF

Removing and installing components

This section provides detailed information on how to remove or install the components from your computer.

GUID-E9F4C483-73BD-41FA-A1BE-DA4A2376E222

Recommended Tools

The procedures in this document may require the following tools:

• Small at-blade screwdriver

• #0 Phillips screwdriver

• #1 Phillips screwdriver

• T5 Torx screwdriver

• Small plastic scribe

GUID-DA12D285-BE8F-419A-BADD-8C7CE1AEEE1A

Base cover

GUID-3123C998-1572-4658-A62D-8E86A41AF044

Removing the Base Cover

1 Follow the procedures in Before Working Inside Your Computer.

2 Close the display and turn the computer over.

3 Turn the system badge ap over (1) and then remove the ten M2x3 screws that secure the base cover to the computer (2).

NOTE: Use a Torx #5 screwdriver for the base screws and a Philips screwdriver for the two M2x8 screws inside the

badge ap.

Removing and installing components 7

4 Pry the edges of the base cover and lift it to remove it from the computer.

GUID-E073DF99-1A77-4432-B2D9-AACC41E4E8ED

Installing the Base Cover

1 Place the base cover on the computer and snap it in place.

2 Tighten the ten M2x3 screws to secure the base cover to the computer.

NOTE: Ensure you use a Torx #5 screwdriver for the base screws and a Philips screwdriver for the two M2x8 system

badge screws.

3 Turn the system badge ap over and snap it in place.

4 Follow the procedures in After Working Inside Your Computer.

GUID-2F290758-2CFF-42C3-A93C-DC0EF3A54A0F

Battery

GUID-9A435B86-16A3-4688-ABDE-1C1AD4EE8944

Removing the Battery

NOTE: Discharge the battery as much as possible before removing from the system. This can be done by disconnecting the A/C

adapter from the system (while the system is turned on) to allow the system to drain the battery.

1 Follow the procedures in Before Working Inside Your Computer.

2 Remove the Base cover

3 Perform the following steps to remove the battery:

a Disconnect the battery cable from the system board [1].

b Remove the seven M2x4 screws that secure the battery to the computer [2].

c Lift the battery o the computer [3].

•Do not apply pressure to the surface of the battery

•Do not bend

8Removing and installing components

•Do not use tools of any kind to pry on or against the battery

• If a battery cannot be removed within the constraints above, please contact Dell technical support

GUID-E6200A72-8A61-4FC7-BC93-E59DE6506F23

Installing the Battery

1 Place and align the battery in the battery bay.

2 Tighten the seven M2x4 screws that secure the battery to the computer.

3 Connect the battery cable to the system board.

4 Install the base cover.

5 Follow the procedures in After Working Inside Your Computer.

GUID-FCB1414D-86F6-40A3-B9CF-A9B9A4F001EF

PCIe Solid State Drive (SSD)

GUID-DCD6B2B6-B8A8-4C8E-B84C-A9ADD634AFE3

Removing the Solid State Drive (SSD)

1 Follow the procedures in Before Working Inside Your Computer

2 Remove the:

aBase cover

bbattery

3 Remove the screw that secures the solid-state drive (SSD) to the system board [1]. Then, slide the SSD out from its connector on the

system board [2].

Removing and installing components 9

GUID-FBD4042D-FB4B-4B98-8138-00AFD44D593A

Installing the solid-state drive

1 Adhere the thermal pad to the solid-state drive.

NOTE: The thermal pad is applicable only for a PCIe SSD card.

2 Slide the solid-state drive at an angle into the solid-state drive slot.

3 Press the other end of the solid-state drive down and replace the M2 x 3 screw that secures the solid-state drive to the system board.

4 Install the:

a battery

b base cover

5 Follow the procedures in After Working Inside Your Computer.

GUID-DA236FEA-AA29-400C-89C3-C25D4B9DE6F3

Hard drive

GUID-18711E8D-0DAD-4F19-8651-0A0E4B02B2C0

Removing the Hard Drive

1 Follow the procedures in Before Working Inside Your Computer.

2 Remove the:

aBase cover

bbattery

3 Perform the following steps to remove the hard-drive bracket from the computer:

10 Removing and installing components

a Remove the four M2x4 screws securing the hard-drive bracket to the computer [1].

b Lift the hard-drive cage [2] o the hard drive assembly [3].

4 Perform the following steps to remove the hard-drive:

a Disconnect the hard-drive cable from the system board [1].

b Lift the hard drive o the palm rest assembly [2].

5 Disconnect the hard drive interposer from the hard drive assembly and then remove the hard drive covers away from the hard drive.

Removing and installing components 11

GUID-85A44711-7A4C-43CF-9BDF-A7CB3BA18D5C

Installing the Hard Drive

1 Replace the hard-drive covers on the hard drive.

2 Connect the hard-drive interposer to the hard-drive assembly.

3 Place the hard-drive assembly on the palm-rest assembly.

4 Connect the hard-drive cable to the system board.

5 Align the screw holes on the hard-drive cage with the screw holes on the hard-drive assembly.

6 Replace the four M2x4 screws that secure the hard-drive cage to the palm-rest assembly.

7 Install the:

a battery

b base cover

8 Follow the procedures in After Working Inside Your Computer.

GUID-A72BE8BB-F2EE-4C6A-A2FE-38F3BD47692A

Speaker

GUID-D1D4BB6A-EA31-4176-B6E4-FF03A661FDBF

Removing the Speakers

1 Follow the procedures in Before Working Inside Your Computer.

2 Remove the:

aBase cover

bbattery

3 Perform the following steps to remove the speaker:

a Disconnect the speaker cable from the system board [1].

b Remove the 4 M2x2 screws that secure the speakers to the computer [2].

c Lift the speakers, along with the speaker cable, o the computer [3].

12 Removing and installing components

GUID-6796D2F3-84EE-44B7-9E08-E5FC243AEF66

Installing the Speakers

1 Using the alignment posts, place the speakers on the palm-rest assembly.

2 Replace the four M2x2 screws that secure the speakers to the palm-rest assembly.

3 Route the speaker cables through the routing guides on the palm-rest assembly.

4 Connect the speaker cable to the system board.

5 Install the:

a battery

b base cover

6 Follow the procedures in After Working Inside Your Computer.

GUID-B369D04D-3080-4AE8-912A-8F95B80E032D

Coin cell battery

GUID-D30B02BB-B807-4138-8C19-A43DFD34AEFE

Removing the Coin-Cell Battery

1 Follow the procedures in Before Working Inside Your Computer.

CAUTION: Removing the coin-cell battery re-sets the BIOS settings to default. It is recommended that you note the

BIOS settings before removing the coin-cell battery.

2 Remove the:

a base cover

Removing and installing components 13

b battery

c WLAN card

d hard drive

e fans

f heatsink assembly

g memory modules

h system board

3 Perform the following steps to remove the coin-cell battery:

a Turn the system board over.

b Lift up the coin cell battery [1]

c Disconnect the coin cell battery cable [2] from the system board [3].

GUID-8827D39A-0406-4415-A1BA-C755AFC4B27A

Installing the Coin-Cell Battery

1 Replace the coin-cell battery in its slot in the computer.

2 Connect the coin-cell battery cable to the system board.

3 Turn the system board over.

4 Install the:

aSystem Board

bMemory

cHeatsink assembly

dFans

eHard drive

fWLAN card

gBattery

hBase cover

5 Follow the procedures in After Working Inside Your Computer.

14 Removing and installing components

GUID-D995663C-CF3C-48E7-AFAE-CA47CB6BAD67

Keyboard

GUID-5C68F0A8-F1DE-43C7-B887-3F4F5A759F21

Removing the Keyboard

1 Follow the procedures in Before Working Inside Your Computer.

2 Remove the:

abase cover

bbattery

cfans

dheatsink

eSSD

fmemory module

gsystem board

3 Perform the following steps to disconnect the keyboard and backlight connectors from the computer.

a Lift up the connector lock [1] and the disconnect the cables from the connectors [2].

b Peel back the screw shields [3].

4 Un-route the LVDS cable [1] and then remove the 31 M1.6 x 1.5 screws that secure the keyboard to the computer [2].

Removing and installing components 15

5 Lift and remove the keyboard from the computer.

GUID-043AA8A4-38B8-4041-AE6D-93ADFFB166F0

Installing the Keyboard

1 Adhere the Mylar to the keyboard.

2 Align the screw holes on the keyboard with the screw holes on the palm-rest assembly.

3 Replace the 31 M1.6 x 1.5 screws that secure the keyboard to the palm-rest assembly.

4 Adhere the Mylar to the screws that secure the keyboard to the palm-rest assembly.

5 Connect the keyboard cable and keyboard-backlight cable to the keyboard-controls board.

16 Removing and installing components

6 Install the:

a system board

b hard drive

c base cover

7 Follow the procedures in After Working Inside Your Computer.

GUID-CCAA203F-6E60-4861-BC9C-1EED5672FD0D

WLAN card

GUID-FC0A2BEF-1723-407E-893D-87A7C79A19DD

Removing the WLAN Card

1 Follow the procedures in Before Working Inside Your Computer.

2 Remove the:

aBase cover

bbattery

3 Perform the following steps to remove the WLAN card:

a Remove the screw to release the bracket that secures the WLAN card to the computer [1] and lift the bracket away from the

computer [2].

b Disconnect the antenna cables from the WLAN card [3].

c Slide and remove the WLAN card from its connector on the board [4].

Removing and installing components 17

GUID-6FE18F1E-BAC8-4EB0-B05F-5440AE7A491F

Installing the WLAN Card

1 Align the notch on the WLAN card with the tab on the WLAN-card connector on the I/O board.

2 Align the bracket which secures the WLAN card to the palmrest assembly.

3 Connect the antenna cables to the WLAN card.

CAUTION: To avoid damage to the WLAN card, do not place any cables under it.

NOTE: The color of the antenna cables is visible near the tip of the cables. The antenna-cable color scheme for the

WLAN card supported by your computer is as follows:

Table 1. Antenna-Cable Color Scheme for the WLAN Card

Connectors on the WLAN card Antenna-cable color

Main (white triangle) white

Auxiliary (black triangle) black

Multiple input, multiple output (grey triangle) Grey (optional)

4 Tighten the screw to secure the bracket and the WLAN card to the palmrest assembly.

5 Install the:

a battery

b base cover

6 Follow the procedures in After Working Inside Your Computer.

GUID-B4BFAFB3-4A6A-47FD-A777-9CA7EF95C20B

Memory module

GUID-DA231FB3-BA92-4287-A1CF-E357B89DBD91

Removing the Memory Module(s)

1 Follow the procedures in Before Working Inside Your Computer.

2 Remove the:

aBase cover

bbattery

3 Pry the securing clips away from the memory module until it pops-up [1]. Then, remove the memory module from its connector on the

system board [2].

18 Removing and installing components

GUID-1B9BB809-6B1D-44AA-B7F1-1A7055CA0ACF

Installing the Memory Module(s)

1 Insert the memory module into the memory socket.

2 Press the memory module down until it clicks into place.

NOTE: If you do not hear the click, remove the memory module and re-install it.

3 Install the:

a battery

b base cover

4 Follow the procedures in After Working Inside Your Computer.

GUID-881CBCDC-CB4E-43B2-A1E2-8D3738554435

System fan

GUID-37E539F9-D872-4602-978C-84559F994A17

Removing the Fans

1 Follow the procedures in Before Working Inside Your Computer.

2 Remove the:

aBase cover

bbattery

3 Perform the following steps to remove the left video-card fan:

a Disconnect the fan cable from the system board [1].

b Remove the two M2x4 screws that secure the fan to the system board[2].

c Lift the fan away from the computer [3]

Removing and installing components 19

4 Perform the following steps to remove the right system fan:

a Un-thread the LVDS cable from its restraints [1].

b Disconnect the fan cable from the system board [2]

c Remove the two M2x4 screws that secure the fan to the computer [3].

d Lift the fan away from the computer [4].

GUID-EE73668A-0B94-4987-ACA4-9C0E7C57C414

Installing the Fans

1 Perform the following steps to install the system fan:

a Align the screw holes on the left fan with the screw holes on the palm-rest assembly.

b Connect the left fan cable to the system board.

c Route the display cable through the routing guides on the left fan.

d Replace the four M2x4 screws that secure the left fan to the system board.

e Connect the right fan cable to the system board.

f Route the touch-screen cable through the routing guides on the right fan.

20 Removing and installing components

g Adhere the tape that secures the touch-screen cable to the right fan.

h Connect the display cable to the system board.

i Replace the four M2x4 screws that secure the right fan to the system board.

2 Follow the procedures in After Working Inside Your Computer.

GUID-ED545F68-B25E-4947-9311-B6FAC5952525

Heat sink

GUID-F4A7F102-2DAD-4A03-8CAE-DC4135D914E1

Removing the Heatsink

1 Follow the procedures in Before Working Inside Your Computer.

2 Remove the:

aBase cover

bbattery

3 Remove the four M2x3 screws that secure the heatsink to the system board.

4 Lift the heatsink o the computer.

Removing and installing components 21

GUID-02CD33DD-EB06-44EE-90DF-4D60A69DD5C9

Installing the Heatsink

1 Align the screw holes on the heatsink with the screw holes on the system board.

2 Replace the screws to secure the heatsink to the system board.

3 Install the:

a battery

b base cover

4 Follow the procedures in After Working Inside Your Computer.

GUID-533F671B-CE7F-422E-AF5B-742BAE7BCF2F

Power connector port

GUID-17B6CFE5-B25E-4170-86C5-553561A2A7FB

Removing the DC-in Connector

1 Follow the procedures in Before Working Inside Your Computer.

2 Remove the:

aBase cover

bbattery

3 Perform the following steps to remove the I/O board:

a Disconnect the DC-in cable from the system board [1].

b Remove the M2x3 screw that secures the DC-in cable to the computer.

22 Removing and installing components

c Remove the DC-in connector from the computer.

GUID-664A224C-7395-4A2A-BB68-EBBF3A330724

Installing the DC-in Adapter Port

1 Place the DC-in adapter port into the slot on the palm-rest assembly.

2 Route the power-adapter port cable through its routing guides on the palm-rest assembly.

3 Replace the M2x3 screw that secures the power-adapter port to the palm-rest assembly.

4 Connect the power-adapter port cable to the system board.

5 Install the:

a battery

b base cover

6 Follow the procedures in After Working Inside Your Computer.

GUID-C7814C13-5EAB-44D9-A0D4-5BE76DD35D1D

Display Assembly

GUID-5FDA2D54-3EA6-42E2-940E-E03375655F52

Removing the Display Assembly

1 Follow the procedures in Before Working Inside Your Computer.

2 Remove the:

aBase cover

bbattery

3 Perform the following steps:

a Remove the screw securing the metal bracket [1].

b Lift the metal bracket o the computer [2].

c Disconnect the LVDS cable from the system board [3].

Removing and installing components 23

4 Place the computer at the edge of a table as shown and remove the six M2.5x5 screws [1] securing the display assembly to the

computer. Then, lift the display assembly o the computer [2].

24 Removing and installing components

GUID-E7992D8F-2DF4-48AA-9925-DC2FF305652A

Installing the Display Assembly

1 Place the palm-rest assembly at the edge of the table with the speakers facing away from the edge.

2 Align the screw holes on the palm-rest assembly with the screw holes on the display hinges.

3 Replace the six M2.5 x 5 screws that secure the display hinges to the palm-rest assembly.

4 Adhere the tape and route the touch-screen cable through the routing guides on the fan.

5 Connect the touch-screen cable and display cable to the system board.

6 Replace the screw that secures the display-cable bracket to the system board.

7 Follow the procedures in After Working Inside Your Computer.

GUID-57A55927-6E1E-400D-8732-224AC53A7435

System board

GUID-369FEBA5-85A8-467C-ACEC-30A1438F183B

Removing the System Board

1 Follow the procedures in Before Working Inside Your Computer.

2 Remove the:

abase cover

bbattery

cfans

dheatsink

eSSD

fmemory module

NOTE: Your computer’s Service Tag is located under the system badge ap. You must enter the Service Tag in the BIOS

after you replace the system board.

NOTE: Before disconnecting the cables from the system board, note the location of the connectors so that you can re-

connect them correctly after you replace the system board.

Removing and installing components 25

3 Remove the M2x2 screw securing the metal bracket for the LVDS to the system board [1] and remove the bracket o the computer

[2]. Then, disconnect the LVDS cable from the system board [3].

4 Slide out the connector latches to disconnect all the cables from the system board.

5 Perform the following steps to remove the system board from the computer:

a Remove the ve M2x4 screws that secure the system board to the computer [1].

b Lift the system board o the computer [2].

26 Removing and installing components

GUID-53816F48-70BA-4DE4-847E-ECB42A7E789D

Installing the System Board

1 Align the system board on the computer.

2 Replace the ve M2x4 screws that secure the system board to the palm-rest assembly.

3 Connect the power-adapter port cable, speaker cable, keyboard-control board cable, touch-pad cable, and touch-screen cable to the

system board.

4 Connect the display cable to the system board.

5 Align the screw hole on the display-cable bracket with the screw hole on the system board.

6 Follow the procedures in After Working Inside Your Computer.

GUID-10F03BEB-3EAC-4085-94EB-E15AEEA0E7ED

Palm rest

GUID-469ACB10-7A2B-413A-82D4-FFC38F993329

Removing the Palmrest Assembly

1 Follow the procedures in Before Working Inside Your Computer.

2 Remove the:

a base cover

b battery

c memory modules

d hard drive

Removing and installing components 27

e WLAN card

f speakers

g heatsink assembly

h fans

i display assembly

j power adapter port

k system board

l keyboard

3 After performing the above steps, we are left with the palmrest assembly [1].

GUID-B2DDB052-1903-455A-9AB5-D417F4935DA1

Installing the Palmrest Assembly

1 Align the palmrest assembly on the display assembly.

2 Tighten the screws to secure the display hinges to the palmrest assembly.

3 Press down on the palmrest assembly to close the display.

4 Install the:

a keyboard

b system board

c power adapter port

d display assembly

e fans

f heatsink assembly

g speakers

h WLAN card

i hard drive

j memory modules

k battery

l base cover

5 Follow the procedures in After Working Inside Your Computer.

28 Removing and installing components

GUID-CE73A0FA-5D0F-4D62-99BE-2753F8278506

Diagnostics

If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of

running diagnostics is to test your computer's hardware without requiring additional equipment or risking data loss. If you are unable to x

the problem yourself, service and support personnel can use the diagnostics results to help you solve the problem.

Topics:

• Enhanced Pre-Boot System Assessment (ePSA) diagnostics

• Device Status Light

GUID-3A3576E1-EF1B-46DB-906F-9A07B70DACE5

Enhanced Pre-Boot System Assessment (ePSA)

diagnostics

The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware. The ePSA is embedded with the

BIOS and is launched by the BIOS internally. The embedded system diagnostics provides a set of options for particular devices or device

groups allowing you to:

• Run tests automatically or in an interactive mode

• Repeat tests

• Display or save test results

• Run thorough tests to introduce additional test options to provide extra information about the failed device(s)

• View status messages that inform you if tests are completed successfully

• View error messages that inform you of problems encountered during testing

CAUTION: Use the system diagnostics to test only your computer. Using this program with other computers may cause invalid

results or error messages.

NOTE: Some tests for specic devices require user interaction. Always ensure that you are present at the computer terminal

when the diagnostic tests are performed.

GUID-E1788E57-6DB4-4B79-97DB-E4888F6AD4CA

Device Status Light

Table 2.

Icon Description

Turns on when you turn on the computer.

Diagnostics 29

GUID-19F7A5B2-F42B-4615-A444-99B63FDDD555

System Setup Options

NOTE: Depending on your computer and its installed devices, the items listed in this section may or may not appear.

Table 3. Main

Option Description

System Time/Date Allows you to set the date and time.

BIOS Version Displays the BIOS version.

Product Name Displays the product name.

Dell Precision 5520 (Default Setting)

Service Tag Displays the service tag.

Asset Tag Displays the asset tag.

None (Default Setting)

CPU Type Displays the CPU type.

CPU Speed Displays the CPU speed.

CPU ID Displays the CPU ID.

CPU Cache Displays the sizes of the CPU caches.

Fixed HDD Displays the type and size of the HDD.

mSATA Device Displays the type and size of the mSATA device.

AC Adapter Type Displays the type of the AC adapter.

None (Default Setting)

System Memory Displays the size of the system memory.

Extended Memory Displays the size of the extended memory.

Memory Speed Displays the speed of the memory.

Keyboard Type Displays the type of keyboard.

Backlite (Default Setting)

Table 4. Advanced

Option Description

Intel (R) SpeedStep (TM) Allows you to enable or disable the Intel (R)

SpeedStep (TM) feature.

Enabled (Default Setting)

Virtualization This option species whether a Virtual Machine

Monitor (VMM) can utilize the additional hardware

capabilities provided by Intel Virtualization technology.

30 System Setup Options

Option Description

Allows you to enable or disable the Virtualization

feature.

Enabled (Default Setting)

Multi Core Support Species whether the processor will have one or

more cores enabled. All (Default Setting)

Intel TurboBoost Enables or disables the Intel TurboBoost mode of the

processor. Enabled (Default Setting)

C-States Control This option enables or disables additional processor

sleep states. Enabled (Default Setting)

Audio Enables or disables the integrated audio controller.

Enabled (Default Setting)

Keyboard Illumination This eld lets you choose the operating mode of the

keyboard illumination feature. Disabled (Default

Setting)

USB Conguration Allows you to congure the integrated USB controller.

Default Enabled: Enable Boot Support, Enable

Thunderbolt Ports; Always Allow Dell Docks; Enable

External USB Port

Touchscreen This eld controls whether the touchscreen is enabled

or disabled. Enabled (Default Setting)

AC Behavior Allows the system (if OFF or in Hibernate) to power-

on automatically when AC is inserted.

Wake On LAN Allows the computer to power up from the o state

when triggered by special LAN. Disabled (Default

Setting)

Advanced Battery Charge Conguration Maximizes battery health while still supporting heavy

use during the work day. Disabled (Default Setting)

Block Sleep Lets you to block entering to sleep (S3 state) in OS

environment. Disabled (Default Setting)

Auto On Time Sets the time of day when you would like the system

to turn on automatically. Disabled (Default Setting)

Peak Shift Minimizes AC power usage at times of peak demand.

Disabled (Default Setting)

USB Wake Support Allows you to enable USB devices to wake the system

from Standby. Enabled (Default Setting)

LCD Brightness This options sets the panel brightness independently

for Battery and AC power.

USB Emulation Allows you to enable or disable the USB Emulation

feature.

Enabled (Default Setting)

USB PowerShare Allows you to enable or disable the USB PowerShare

feature.

Enabled (Default Setting)

USB Wake Support This option allows you to enable USB devices to wake

the system from Standby.

Disable(Default Setting)

System Setup Options 31

Option Description

SATA Operation Displays the SATA Operation information.

Adapter Warnings Allows you to enable or disable the adapter warnings

feature.

Multimedia Key Behaviour Function Key (Default Setting)

Battery Health Displays the battery health information.

Battery Charge Conguration Adaptive (Default Setting)

Miscellaneous Devices Allows you enable or disable the various on board

devices. The options are:

•External USB Ports - Enabled (Default Setting)

•USB Debug - Disabled (Default Setting)

Table 5. Security

Option Description

Unlock Setup Status Unlocked (Default Setting)

Admin Password Status Displays the status of the admin password.

Default Setting: Not set

System Password Status Displays the status of the system password.

Default Setting: Not set

HDD Password Status Displays the status of the system password.

Default Setting: Not set

Asset Tag Allows you to set the asset tag.

Admin Password Allows you to set, change, or delete the administrator (admin) password.

NOTE: You must set the admin password before you set the system or hard drive

password.

NOTE: Successful password changes take eect immediately.

NOTE: Deleting the admin password automatically deletes the system password and

the hard drive password.

NOTE: Successful password changes take eect immediately.

System Password Allows you to set, change or delete the system password.

NOTE: Successful password changes take eect immediately.

HDD Password Allows you to set, change or delete the administrator password.

Strong Password This eld enforces strong passwords that contain at least one uppercase character, one

lowercase character, and be at least 8 characters long.

Password Change Allows you to enable or disable permissions to set a System password and a Hard Drive

password when the admin password is set.

Default Setting: Permitted

Password Bypass This option lets you bypass the System (Boot) password and the internal HDD password

prompts during system re-start. Disabled (Default Setting)

32 System Setup Options

Option Description

Password conguration These elds control the minimum and maximum number of characters allowed for Admin and

System passwords.

Computrace Allows you to activate or disable the optional Computrace software The options are:

•Deactivate (Default Setting)

• Activate

NOTE: The Activate and Disable options will permanently activate or disable the

feature and no further changes will be allowed.

TPM Security This option lets you control whether the Trusted Platform Module (TPM) in the system is

enabled and visible to the operating system. When disabled the BIOS will not turn On the TPM

During POST. The TPM will be non-functional and invisible to the operating system. When

enabled, the BIOS will turn On the TPM during POST so that it can be used by the operating

system. This option is Enable by default.

NOTE: Disabling this option does not change any settings you may have made to the

TPM, nor does it delete or change any information or keys you may have stored

there. It simply turns O the TPM so that it cannot be used. When you re-enable

this option, the TPM will function exactly as it did before it was disabled.

NOTE: Changes to this option take eect immediately.

UEFI Capsule Firmware Updates This option controls whether this system allows BIOS updates via UEFI capsule update

packages. Enabled (Default Setting)

CPU XD Support This option enables or disables the Execute Disable mode for the processor. Enabled (Default

Setting)

OROM Keyboard Access This option determines whether users are able to enter Option ROM conguration screens via

hotkeys during boot.

Table 6. Boot

Option Description

Boot List Option Default Setting: Legacy

Secure Boot This option enables or disables the Secure Boot

feature.

•Disabled (Default Setting) - Windows 7 (Intel

Core Xeon E3–1505M v5 and Intel Core i7–

6820HQ processors)

• Enabled - Windows 8.1 and Windows 10 (Intel

Core Xeon E3–1505M; Intel Core i7–7820HQ; Intel

Core i7–7700HQ; Intel Core i5–7440HQ; and Intel

Core i5–7300HQ processors)

Load Legacy Option ROM This option enables or disables the Load Legacy

Option ROM feature.

•Enabled (Default Setting) - Windows 7

• Disabled - Windows 8.1 and Windows 10

Expert Key Management Expert Key Management allows the PK, KEK, db, and

dbx security key databases to be manipulated.

Disabled (Default Setting)

Intel Software Guard Extensions Intel SGX Enabled: Enables Intel Software Guard

Extensions (SGX) to provide a secured environment

for running code/storing sensitive information in the

System Setup Options 33

Option Description

context of the main OS. Software Controlled

(Default Setting)

Set Boot Priority Allows you to change the order in which the

computer attempts to nd an operating system:

• 1 st Boot Priority [ CD/DVD/CD-RW Drive]

• 2nd Boot Priority [Network]

• 3rd Boot Priority [mini SSD]

• 4th Boot Priority [USB Storage Device

• 5th Boot Priority [Hard Drive]

• 6th Boot Priority [Diskette Drive]

Adapter Warnings Lets you choose whether the system displays warning

messages when you use certain power adapters.

Enabled (Default Setting)

SupportAssist OS Recovery Enables for disables the boot ow for SupportAssist

OS Recovery tool in the event of certain errors.

Enabled (Default Setting)

Keypad (embedded) Lets you choose one of two methods to enable the

keypad that is embedded in the internal keyboard. Fn

Key Only Enabled by default.

Fastboot This option can speed up the boot process by

bypassing some compatibility steps. Minimal (Default

Setting)

Extend BIOS POST Time Creates an additional pre-boot delay to see POST

messages.

Warnings and Errors This option cause the boot process to only pause

when warnings or errors are detected. Enabled

(Default Setting)

Wireless Switch Determines which wireless devices can be controlled

by the Wireless Switch. WLAN and Bluetooth Enabled

(Default Setting)

SupportAssist System Resolution Auto OS Recovery Threshold: Controls the automatic

boot ow for SupportAssist System Resolution

Console and for Dell OS Recovery Tool. Setting 2

default

Table 7. Exit

Option Description

Save Changes and Reset Allows you to save the changes you made.

Discard Changes and Reset Allows you to discard the changes you made.

Restore Defaults Allows you to restore the default options.

Discard Changes Allows you to discard the changes you made.

Save Changes Allows you to save the changes you made.

34 System Setup Options

GUID-32E2FD6D-3734-4E0A-A340-D8164E73523E

Technical Specications

NOTE: Oerings may vary by region. For more information regarding the conguration of your computer, click Start (Start

icon) > Help and Support, and then select the option to view information about your computer.

Table 8. System Information

Feature Specication

System Chipset Mobile Intel HM175 Express Chipset / Intel CM238

DMA Channels two VT-d DMA remap engines

Interrupt Levels Intel 64 and IA-32 Architecture

BIOS Chip (NVRAM) 32 MB SPI ROM

Table 9. Processor

Feature Specication

Processor type 6th Generation:

• Intel Core Xeon E3–1505M v5

• Intel Core i7–6820HQ

7th Generation

• Intel Core Xeon E3–1505M v6

• Intel Core i7–7820HQ

• Intel Core i7–7700HQ

• Intel Core i5–7440HQ

• Intel Core i5–7300HQ

L1 cache up to 256 KB cache depending on processor type

L2 cache up to 1024 KB cache depending on processor type

L3 cache up to 6144 KB cache depending on processor type

Table 10. Memory

Feature Specication

Type DDR4

Speed 2400 MHz

NOTE: 2133 MHz with 6th Generation processors

Connectors 2 SoDIMM Sockets

Capacity 8 GB, 16 GB, and 32 GB

Technical Specications 35

Feature Specication

Minimum Memory 8 GB (2 x 4 GB)

Maximum memory 32 GB

Table 11. Video

Feature Specication

Type

Discrete NVIDIA Quadro M1200 / 4 GB GDDR5

Integrated • Intel HD Graphics 630/P630 with 7th Generation processors

• Intel HD Graphics 530 with 6th Generation processors

Data bus PCIE x16, Gen3

Memory

Discrete Up to 4 GB GDDR5

Integrated Shared system memory

Table 12. Audio

Feature Specication

Integrated dual-channel High-Denition audio

Table 13. Communication

Feature Specication

Network adapter Ethernet via USB-to-Ethernet Dongle provided in box.

NOTE: No RJ45 (10/100/1000Base-T, IPv6) provided.

Wireless • Wi-Fi 802.11ac

• Wi-Fi 802.11a/g/n

• Bluetooth 4.2

• Miracast

Table 14. Ports and Connectors

Feature Specication

Audio • One headset port (headphone and microphone combo)

USB 3.0 • two USB 3.0 ports with PowerShare

• One Thunderbolt 3 port (USB-C)

Video • one HDMI 1.4

Memory card reader SD 4.0

36 Technical Specications

Table 15. Display

Feature Specication

Type 1920 x 1080 FHD

3840 x 2160 UltraHD Touch

100% Adobe Color gamut minimum

Size 15.6 inches FHD

15.6 inches UltraHD

Dimensions:

Height 194.50 mm (7.66 in)

Width 345.60 mm (13.61 in)

Diagonal 396.52 mm (15.61 in)

Active area (X/Y) 194.50 mm (7.66 in) x 345.60 mm (13.61 in) x 396.52 mm (15.61 in)

Maximum resolution 1920 X 1080 pixels / 3840 X 2160 pixels

Maximum Brightness 400 nits

Operating angle 0° (closed) to 135°

Refresh rate 60 Hz

Minimum viewing angles:

Horizontal 80/80

Vertical 80/80

Table 16. Keyboard

Feature Specication

Number of keys • United States: 80 keys

• United Kingdom: 81 keys

• Brazil: 80 keys

• Japan: 84 keys

Layout QWERTY/AZERTY/Kanji

Table 17. Touchpad

Feature Specication

Active Area:

X-axis 105 mm

Y-axis 80 mm

Technical Specications 37

Table 18. Camera

Feature Specication

Type HD Camera / Digital Array Microphone

Still Resolution 0.92 megapixels (Maximum)

Video Resolution 1280 x 720 pixels (HD) at 30 frames per second (Maximum)

Diagonal 74 degrees

Table 19. Storage

Feature Specication

Storage:

Storage Interface SATA 3 Gbps

SATA 6 Gbps

PCIe 8 Gbps

Drives congurations:

Hard Drives (optional) one internal 2.5 inch SATA HDD (supports Intel Smart Response Technology)

Solid State Drives (optional) one Solid State Drive (SSD), with Intel Cache support

Size: 512 GB / 1 TB/ 2 TB HDD

256 GB / 360 GB / 512 GB / 1 TB SSD

Table 20. Battery

Feature Specication

Type Li-polymer 3-cell (56 Whr) / 6-cell (97 Whr)

Dimensions :

56 Whr :

Depth 223.20 mm (8.79 in)

Height 7.20 mm (0.28 in)

Width 71.80 mm (2.83 in)

Weight 0.54 lb (0.24 kg)

84 Whr :

Depth 330.50 mm (13.01 in)

Height 7.20 mm (0.28 in)

Width 71.80 mm (2.83 in)

Weight 0.76 lb (0.34 kg)

Voltage 11.4 V

Life span 300 discharge/charge cycles

Temperature range:

Operating (approximate) • Operating: 0 °C to 35 °C (32 °F to 95 °F)

38 Technical Specications

Feature Specication

• Charge : 0 °C to 50 °C (32 °F to 122 °F)

• Discharge: 0 °C to 70 °C (32 °F to 158 °F)

Non-operating –40 °C to 65 °C (–40 °F to 149 °F)

Coin-cell battery ML1220

Table 21. AC Adapter

Feature Specication

Input voltage 100 VAC to 240 VAC

Input current (maximum) 1.80 A

Input frequency 50 Hz to 60 Hz

Output power 130 W

Output current 6.67 A

Rated output voltage 19.50 VDC

Dimensions:

Height 22 mm (0.86 inches)

Width 66 mm (2.59 inches)

Depth 143 mm (5.62 inches)

Temperature range:

Operating 0 °C to 40 °C (32 °F to 104 °F)

Non Operating –40 °C to 70 °C (–40 °F to 158 °F)

Table 22. Physical Dimensions

Physical Specication

Height: 17 mm (0.66 in)

Width 357 mm (14.06 in)

Depth 235 mm (9.27 in)

Weight (Minimum) 2 kg (4.41 lb)

Table 23. Environmental

Feature Specication

Temperature range:

Operating 0 °C to 40 °C (32 °F to 104°F)

Storage –40 °C to 70 °C (–40 °F to 158 °F)

Relative humidity (maximum):

Operating 10 % to 90 % (non-condensing)

Storage 10 % to 95 % (non-condensing)

Technical Specications 39

Feature Specication

Maximum vibration:

Operating 0.66 GRMS, 2 Hz - 600 Hz

Storage 1.3 GRMS, 2 Hz - 600 Hz

Maximum shock:

Operating 110 G, 2 ms

Non-operating 160 G, 2 ms

Altitude:

Operating –15.2 m to 3048 m (–50 to 10,000 ft)

Storage 15.2 m to 10,668 m (–50 ft to 35,000 ft)

Airborne contaminant level G1 as dened by ISA-S71.04-1985

40 Technical Specications

GUID-7A3627F9-0363-4515-A1D4-1B7878F4B8C4

Contacting Dell

NOTE: If you do not have an active Internet connection, you can nd contact information on your purchase invoice, packing slip,

bill, or Dell product catalog.

Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services

may not be available in your area. To contact Dell for sales, technical support, or customer service issues:

1 Go to Dell.com/support.

2 Select your support category.

3 Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.

4 Select the appropriate service or support link based on your need.

Contacting Dell 41

Table of Contents

DELL 5520 User Manual

Related Manuals