Table of Contents
- Inspiron 5583 Service Manual
- Before working inside your computer
- After working inside your computer
- Safety instructions
- Recommended tools
- Screw list
- Removing the optical drive
- Replacing the optical drive
- Removing the base cover
- Replacing the base cover
- Removing the battery
- Replacing the battery
- Removing the memory modules
- Replacing the memory modules
- Removing the wireless card
- Replacing the wireless card
- Removing the optical-drive connector board
- Replacing the optical-drive connector board
- Removing the fan
- Replacing the fan
- Removing the coin-cell battery
- Replacing the coin-cell battery
- Removing the solid-state drive/Intel Optane memory module
- Replacing the solid-state drive/Intel Optane memory module
- Removing the hard drive
- Replacing the hard drive
- Removing the speakers
- Replacing the speakers
- Removing the touchpad
- Replacing the touchpad
- Removing the heat sink
- Replacing the heat sink
- Removing the power-adapter port
- Replacing the power-adapter port
- Removing the I/O board
- Replacing the I/O board
- Removing the power-button board
- Replacing the power-button board
- Removing the power button with fingerprint reader
- Replacing the power button with fingerprint reader
- Removing the display assembly
- Replacing the display assembly
- Removing the system board
- Replacing the system board
- Removing the palm-rest and keyboard assembly
- Replacing the palm-rest and keyboard assembly
- Removing the display bezel
- Replacing the display bezel
- Removing the camera
- Replacing the camera
- Removing the display panel
- Replacing the display panel
- Removing the display hinges
- Replacing the display hinges
- Removing the display cable
- Replacing the display cable
- Removing the display back-cover and antenna assembly
- Replacing the display back-cover and antenna assembly
- Device drivers
- System setup
- Troubleshooting
- Getting help and contacting Dell
DELL 5583 User Manual
Displayed below is the user manual for 5583 by DELL which is a product in the Notebooks category. This manual has pages.
Related Manuals
Inspiron 5583
Service Manual
Regulatory Model: P86F
Regulatory Type: P86F001
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the
problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2018 - 2019 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its
subsidiaries. Other trademarks may be trademarks of their respective owners.
2019 - 02
Rev. A00
1 Before working inside your computer............................................................................................. 9
Before you begin ...................................................................................................................................................................9
2 After working inside your computer..............................................................................................10
3 Safety instructions...................................................................................................................... 11
Electrostatic discharge—ESD protection......................................................................................................................... 11
ESD field service kit ............................................................................................................................................................ 12
Transporting sensitive components...................................................................................................................................13
4 Recommended tools....................................................................................................................14
5 Screw list...................................................................................................................................15
6 Removing the optical drive...........................................................................................................17
Procedure..............................................................................................................................................................................17
7 Replacing the optical drive...........................................................................................................19
Procedure .............................................................................................................................................................................19
8 Removing the base cover.............................................................................................................21
Prerequisites......................................................................................................................................................................... 21
Procedure..............................................................................................................................................................................21
9 Replacing the base cover............................................................................................................ 24
Procedure ............................................................................................................................................................................24
Post-requisites.....................................................................................................................................................................26
10 Removing the battery................................................................................................................ 27
Lithium-ion battery precautions.........................................................................................................................................27
Prerequisites.........................................................................................................................................................................27
Procedure............................................................................................................................................................................. 27
11 Replacing the battery................................................................................................................ 29
Lithium-ion battery precautions........................................................................................................................................ 29
Procedure ............................................................................................................................................................................29
Post-requisites.....................................................................................................................................................................30
12 Removing the memory modules.................................................................................................. 31
Removing the speakers....................................................................................................................................................... 31
Prerequisites................................................................................................................................................................... 31
Procedure........................................................................................................................................................................31
Procedure............................................................................................................................................................................. 32
Contents
Contents 3
13 Replacing the memory modules.................................................................................................. 34
Procedure ............................................................................................................................................................................34
Replacing the speakers.......................................................................................................................................................34
Procedure ...................................................................................................................................................................... 34
Post-requisites...............................................................................................................................................................35
14 Removing the wireless card....................................................................................................... 36
Prerequisites........................................................................................................................................................................ 36
Procedure.............................................................................................................................................................................36
15 Replacing the wireless card........................................................................................................38
Procedure............................................................................................................................................................................. 38
Post-requisites.....................................................................................................................................................................38
16 Removing the optical-drive connector board............................................................................... 39
Procedure.............................................................................................................................................................................39
17 Replacing the optical-drive connector board................................................................................40
Procedure ............................................................................................................................................................................40
18 Removing the fan...................................................................................................................... 41
Procedure..............................................................................................................................................................................41
19 Replacing the fan...................................................................................................................... 42
Procedure ............................................................................................................................................................................42
20 Removing the coin-cell battery.................................................................................................. 43
Prerequisites.........................................................................................................................................................................43
Procedure............................................................................................................................................................................. 43
21 Replacing the coin-cell battery...................................................................................................44
Procedure............................................................................................................................................................................. 44
Post-requisites.....................................................................................................................................................................44
22 Removing the solid-state drive/Intel Optane memory module.......................................................45
Procedure.............................................................................................................................................................................45
23 Replacing the solid-state drive/Intel Optane memory module....................................................... 47
Procedure to move the M.2 screw mount.......................................................................................................................47
Procedure ............................................................................................................................................................................48
24 Removing the hard drive............................................................................................................51
Prerequisites......................................................................................................................................................................... 51
Procedure..............................................................................................................................................................................51
25 Replacing the hard drive........................................................................................................... 53
Procedure ............................................................................................................................................................................53
4Contents
Post-requisites.....................................................................................................................................................................54
26 Removing the speakers............................................................................................................. 55
Prerequisites........................................................................................................................................................................ 55
Procedure.............................................................................................................................................................................55
27 Replacing the speakers............................................................................................................. 56
Procedure ............................................................................................................................................................................56
Post-requisites.....................................................................................................................................................................56
28 Removing the touchpad............................................................................................................ 57
Prerequisites.........................................................................................................................................................................57
Procedure............................................................................................................................................................................. 57
29 Replacing the touchpad............................................................................................................ 59
Procedure ............................................................................................................................................................................59
Post-requisites.....................................................................................................................................................................60
30 Removing the heat sink............................................................................................................. 61
Prerequisites......................................................................................................................................................................... 61
Procedure..............................................................................................................................................................................61
31 Replacing the heat sink..............................................................................................................63
Procedure ............................................................................................................................................................................63
Post-requisites.....................................................................................................................................................................63
32 Removing the power-adapter port............................................................................................. 65
Removing the display assembly.........................................................................................................................................65
Prerequisites...................................................................................................................................................................65
Procedure....................................................................................................................................................................... 65
Procedure.............................................................................................................................................................................68
33 Replacing the power-adapter port..............................................................................................70
Procedure ............................................................................................................................................................................ 70
Replacing the display assembly...........................................................................................................................................71
Procedure ....................................................................................................................................................................... 71
Post-requisites............................................................................................................................................................... 73
34 Removing the I/O board............................................................................................................ 74
Prerequisites.........................................................................................................................................................................74
Procedure............................................................................................................................................................................. 74
35 Replacing the I/O board............................................................................................................ 76
Procedure ............................................................................................................................................................................ 76
Post-requisites..................................................................................................................................................................... 76
36 Removing the power-button board............................................................................................. 77
Prerequisites.........................................................................................................................................................................77
Contents 5
Procedure............................................................................................................................................................................. 77
37 Replacing the power-button board............................................................................................. 79
Procedure ............................................................................................................................................................................ 79
Post-requisites.....................................................................................................................................................................80
38 Removing the power button with fingerprint reader.....................................................................81
Prerequisites......................................................................................................................................................................... 81
Procedure..............................................................................................................................................................................81
39 Replacing the power button with fingerprint reader.................................................................... 83
Procedure ............................................................................................................................................................................83
Post-requisites.....................................................................................................................................................................83
40 Removing the display assembly................................................................................................. 85
Prerequisites........................................................................................................................................................................ 85
Procedure.............................................................................................................................................................................85
41 Replacing the display assembly.................................................................................................. 88
Procedure ............................................................................................................................................................................88
Post-requisites.....................................................................................................................................................................89
42 Removing the system board...................................................................................................... 90
Prerequisites........................................................................................................................................................................ 90
Procedure.............................................................................................................................................................................90
43 Replacing the system board.......................................................................................................94
Procedure.............................................................................................................................................................................94
Post-requisites.....................................................................................................................................................................96
Entering the Service Tag in the BIOS setup program.................................................................................................... 96
44 Removing the palm-rest and keyboard assembly......................................................................... 97
Prerequisites.........................................................................................................................................................................97
Procedure............................................................................................................................................................................. 97
45 Replacing the palm-rest and keyboard assembly......................................................................... 99
Procedure.............................................................................................................................................................................99
Post-requisites.....................................................................................................................................................................99
46 Removing the display bezel.......................................................................................................101
Prerequisites........................................................................................................................................................................101
Procedure............................................................................................................................................................................ 101
47 Replacing the display bezel...................................................................................................... 102
Procedure .......................................................................................................................................................................... 102
Post-requisites................................................................................................................................................................... 102
48 Removing the camera.............................................................................................................. 103
6Contents
Prerequisites.......................................................................................................................................................................103
Procedure........................................................................................................................................................................... 103
49 Replacing the camera.............................................................................................................. 105
Procedure .......................................................................................................................................................................... 105
Post-requisites................................................................................................................................................................... 105
50 Removing the display panel...................................................................................................... 107
Prerequisites....................................................................................................................................................................... 107
Procedure............................................................................................................................................................................107
51 Replacing the display panel...................................................................................................... 109
Procedure .......................................................................................................................................................................... 109
Post-requisites.................................................................................................................................................................... 110
52 Removing the display hinges..................................................................................................... 111
Prerequisites.........................................................................................................................................................................111
Procedure............................................................................................................................................................................. 111
53 Replacing the display hinges.....................................................................................................113
Procedure ........................................................................................................................................................................... 113
Post-requisites.................................................................................................................................................................... 113
54 Removing the display cable.......................................................................................................115
Prerequisites........................................................................................................................................................................115
Procedure............................................................................................................................................................................ 115
55 Replacing the display cable.......................................................................................................116
Procedure ........................................................................................................................................................................... 116
Post-requisites.................................................................................................................................................................... 116
56 Removing the display back-cover and antenna assembly............................................................. 117
Prerequisites........................................................................................................................................................................ 117
Procedure.............................................................................................................................................................................117
57 Replacing the display back-cover and antenna assembly............................................................. 119
Procedure ........................................................................................................................................................................... 119
Post-requisites.................................................................................................................................................................... 119
58 Device drivers..........................................................................................................................121
Intel Chipset Software Installation Utility.........................................................................................................................121
Video drivers........................................................................................................................................................................121
Intel Serial IO driver............................................................................................................................................................ 121
Intel Trusted Execution Engine Interface........................................................................................................................ 121
Intel Virtual Button driver...................................................................................................................................................121
Wireless and Bluetooth drivers......................................................................................................................................... 121
59 System setup..........................................................................................................................122
Contents 7
System setup......................................................................................................................................................................122
Entering BIOS setup program.......................................................................................................................................... 122
Navigation keys.................................................................................................................................................................. 122
Boot Sequence...................................................................................................................................................................122
Clearing CMOS settings....................................................................................................................................................123
Clearing BIOS (System Setup) and System passwords............................................................................................... 123
60 Troubleshooting......................................................................................................................124
Flashing the BIOS...............................................................................................................................................................124
Flashing BIOS (USB key).................................................................................................................................................. 124
Enhanced Pre-Boot System Assessment (ePSA) diagnostics.................................................................................... 124
Running the ePSA diagnostics................................................................................................................................... 125
System diagnostic lights................................................................................................................................................... 125
Enabling Intel Optane memory......................................................................................................................................... 126
Disabling Intel Optane memory........................................................................................................................................ 126
WiFi power cycle................................................................................................................................................................126
Flea power release............................................................................................................................................................. 126
61 Getting help and contacting Dell............................................................................................... 128
8Contents
Before working inside your computer
NOTE: The images in this document may differ from your computer depending on the configuration you ordered.
Before you begin
1. Save and close all open files and exit all open applications.
2. Shut down your computer. Click Start > Power > Shut down.
NOTE: If you are using a different operating system, see the documentation of your operating system for shut-down
instructions.
3. Disconnect your computer and all attached devices from their electrical outlets.
4. Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your computer.
5. Remove any media card and optical disc from your computer, if applicable.
1
Before working inside your computer 9
After working inside your computer
CAUTION: Leaving stray or loose screws inside your computer may severely damage your computer.
1. Replace all screws and ensure that no stray screws remain inside your computer.
2. Connect any external devices, peripherals, or cables you removed before working on your computer.
3. Replace any media cards, discs, or any other parts that you removed before working on your computer.
4. Connect your computer and all attached devices to their electrical outlets.
5. Turn on your computer.
2
10 After working inside your computer
Safety instructions
Use the following safety guidelines to protect your computer from potential damage and ensure your personal safety.
NOTE: Before working inside your computer, read the safety information that shipped with your computer. For more
safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance.
NOTE: Disconnect all power sources before opening the computer cover or panels. After you finish working inside the
computer, replace all covers, panels, and screws before connecting to the electrical outlet.
CAUTION: To avoid damaging the computer, ensure that the work surface is flat and clean.
CAUTION: To avoid damaging the components and cards, handle them by their edges, and avoid touching pins and
contacts.
CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical
assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety
instructions that shipped with the product or at www.dell.com/regulatory_compliance.
CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface,
such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to
dissipate static electricity, which could harm internal components.
CAUTION: When you disconnect a cable, pull on its connector or on its pull tab, not on the cable itself. Some cables have
connectors with locking tabs or thumb-screws that you must disengage before disconnecting the cable. When
disconnecting cables, keep them evenly aligned to avoid bending any connector pins. When connecting cables, ensure
that the ports and connectors are correctly oriented and aligned.
CAUTION: Press and eject any installed card from the media-card reader.
Electrostatic discharge—ESD protection
ESD is a major concern when you handle electronic components, especially sensitive components such as expansion cards, processors,
memory DIMMs, and system boards. Very slight charges can damage circuits in ways that may not be obvious, such as intermittent
problems or a shortened product life span. As the industry pushes for lower power requirements and increased density, ESD protection is
an increasing concern.
Due to the increased density of semiconductors used in recent Dell products, the sensitivity to static damage is now higher than in
previous Dell products. For this reason, some previously approved methods of handling parts are no longer applicable.
Two recognized types of ESD damage are catastrophic and intermittent failures.
•Catastrophic – Catastrophic failures represent approximately 20 percent of ESD-related failures. The damage causes an immediate
and complete loss of device functionality. An example of catastrophic failure is a memory DIMM that has received a static shock and
immediately generates a "No POST/No Video" symptom with a beep code emitted for missing or nonfunctional memory.
•Intermittent – Intermittent failures represent approximately 80 percent of ESD-related failures. The high rate of intermittent failures
means that most of the time when damage occurs, it is not immediately recognizable. The DIMM receives a static shock, but the
tracing is merely weakened and does not immediately produce outward symptoms related to the damage. The weakened trace may
take weeks or months to melt, and in the meantime may cause degradation of memory integrity, intermittent memory errors, etc.
The more difficult type of damage to recognize and troubleshoot is the intermittent (also called latent or "walking wounded") failure.
Perform the following steps to prevent ESD damage:
• Use a wired ESD wrist strap that is properly grounded. The use of wireless anti-static straps is no longer allowed; they do not provide
adequate protection. Touching the chassis before handling parts does not ensure adequate ESD protection on parts with increased
sensitivity to ESD damage.
• Handle all static-sensitive components in a static-safe area. If possible, use anti-static floor pads and workbench pads.
3
Safety instructions 11
• When unpacking a static-sensitive component from its shipping carton, do not remove the component from the anti-static packing
material until you are ready to install the component. Before unwrapping the anti-static packaging, ensure that you discharge static
electricity from your body.
• Before transporting a static-sensitive component, place it in an anti-static container or packaging.
ESD field service kit
The unmonitored Field Service kit is the most commonly used service kit. Each Field Service kit includes three main components: anti-
static mat, wrist strap, and bonding wire.
Components of an ESD field service kit
The components of an ESD field service kit are:
•Anti-Static Mat – The anti-static mat is dissipative and parts can be placed on it during service procedures. When using an anti-
static mat, your wrist strap should be snug and the bonding wire should be connected to the mat and to any bare metal on the system
being worked on. Once deployed properly, service parts can be removed from the ESD bag and placed directly on the mat. ESD-
sensitive items are safe in your hand, on the ESD mat, in the system, or inside a bag.
•Wrist Strap and Bonding Wire – The wrist strap and bonding wire can be either directly connected between your wrist and bare
metal on the hardware if the ESD mat is not required, or connected to the anti-static mat to protect hardware that is temporarily
placed on the mat. The physical connection of the wrist strap and bonding wire between your skin, the ESD mat, and the hardware is
known as bonding. Use only Field Service kits with a wrist strap, mat, and bonding wire. Never use wireless wrist straps. Always be
aware that the internal wires of a wrist strap are prone to damage from normal wear and tear, and must be checked regularly with a
wrist strap tester in order to avoid accidental ESD hardware damage. It is recommended to test the wrist strap and bonding wire at
least once per week.
•ESD Wrist Strap Tester – The wires inside of an ESD strap are prone to damage over time. When using an unmonitored kit, it is a
best practice to regularly test the strap prior to each service call, and at a minimum, test once per week. A wrist strap tester is the
best method for doing this test. If you do not have your own wrist strap tester, check with your regional office to find out if they have
one. To perform the test, plug the wrist-strap's bonding-wire into the tester while it is strapped to your wrist and push the button to
test. A green LED is lit if the test is successful; a red LED is lit and an alarm sounds if the test fails.
•Insulator Elements – It is critical to keep ESD sensitive devices, such as plastic heat sink casings, away from internal parts that are
insulators and often highly charged.
•Working Environment – Before deploying the ESD Field Service kit, assess the situation at the customer location. For example,
deploying the kit for a server environment is different than for a desktop or portable environment. Servers are typically installed in a
rack within a data center; desktops or portables are typically placed on office desks or cubicles. Always look for a large open flat work
area that is free of clutter and large enough to deploy the ESD kit with additional space to accommodate the type of system that is
being repaired. The workspace should also be free of insulators that can cause an ESD event. On the work area, insulators such as
Styrofoam and other plastics should always be moved at least 12 inches or 30 centimeters away from sensitive parts before physically
handling any hardware components.
•ESD Packaging – All ESD-sensitive devices must be shipped and received in static-safe packaging. Metal, static-shielded bags are
preferred. However, you should always return the damaged part using the same ESD bag and packaging that the new part arrived in.
The ESD bag should be folded over and taped shut and all the same foam packing material should be used in the original box that the
new part arrived in. ESD-sensitive devices should be removed from packaging only at an ESD-protected work surface, and parts
should never be placed on top of the ESD bag because only the inside of the bag is shielded. Always place parts in your hand, on the
ESD mat, in the system, or inside an anti-static bag.
•Transporting Sensitive Components – When transporting ESD sensitive components such as replacement parts or parts to be
returned to Dell, it is critical to place these parts in anti-static bags for safe transport.
ESD protection summary
It is recommended that all field service technicians use the traditional wired ESD grounding wrist strap and protective anti-static mat at all
times when servicing Dell products. In addition, it is critical that technicians keep sensitive parts separate from all insulator parts while
performing service and that they use anti-static bags for transporting sensitive components.
12 Safety instructions
Transporting sensitive components
When transporting ESD sensitive components such as replacement parts or parts to be returned to Dell, it is critical to place these parts in
anti-static bags for safe transport.
Lifting equipment
Adhere to the following guidelines when lifting heavy weight equipment:
CAUTION: Do not lift greater than 50 pounds. Always obtain additional resources or use a mechanical lifting device.
1. Get a firm balanced footing. Keep your feet apart for a stable base, and point your toes out.
2. Tighten stomach muscles. Abdominal muscles support your spine when you lift, offsetting the force of the load.
3. Lift with your legs, not your back.
4. Keep the load close. The closer it is to your spine, the less force it exerts on your back.
5. Keep your back upright, whether lifting or setting down the load. Do not add the weight of your body to the load. Avoid twisting your
body and back.
6. Follow the same techniques in reverse to set the load down.
Safety instructions 13
Recommended tools
The procedures in this document may require the following tools:
• Phillips screwdriver #1
• Flat-head screwdriver
• Plastic scribe
4
14 Recommended tools
Screw list
NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws,
and then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type
is restored when the component is replaced.
NOTE: Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surface when
replacing a component.
NOTE: Screw color may vary with the configuration ordered.
Table 1. Screw list
Component Secured to Screw type Quantity Screw image
Optical-disk drive Palm-rest and keyboard
assembly
M2x3 1
Base cover Palm-rest and keyboard
assembly
M2.5x6 5
Base cover Palm-rest and keyboard
assembly
M1.2x1.2 2
Battery Palm-rest and keyboard
assembly
M2x3 4
Display panel Display back-cover and
antenna assembly
M2x2.5 4
Fan Palm-rest and keyboard
assembly
M2x3 3
Hard-drive assembly Palm-rest and keyboard
assembly
M2x3 3
Hard-drive bracket Hard drive M3x3 4
Heat sink (for computers
shipped with discrete
graphics)
System board M2x3 3
Hinges Palm-rest and keyboard
assembly
M2.5x5 6
Hinge brackets Display back-cover and
antenna assembly
M2x2 8
Optical-drive bracket Optical drive M2x3 2
Optical-drive connector
board
Palm-rest and keyboard
assembly
M2x2 1
Power-adapter port Palm-rest and keyboard
assembly
M2x3 1
Power-button board Palm-rest and keyboard
assembly
M2x2 2
5
Screw list 15
Component Secured to Screw type Quantity Screw image
Solid-state drive/Intel
Optane
Palm-rest and keyboard
assembly
M2x3 1
System board Palm-rest and keyboard
assembly
M2x3 2
System board Palm-rest and keyboard
assembly
M2x2 2
Touchpad bracket Palm-rest and keyboard
assembly
M2x2 3
Wireless-card bracket System board M2x3 1
16 Screw list
Removing the optical drive
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1. Remove the screw (M2x3) that secures the optical-drive assembly to the palm-rest and keyboard assembly.
2. Using a screwdriver, carefully push the optical-drive assembly through the slot to release the optical-drive assembly out of the optical-
drive bay.
3. Slide the optical-drive assembly out of the optical-drive bay.
4. Remove the two screws (M2x3) that secure the optical-drive bracket to the optical drive.
5. Remove the optical-drive bracket from optical drive.
6
Removing the optical drive 17
6. Pull the optical-drive bezel carefully to remove it from the optical drive.
18 Removing the optical drive
Replacing the optical drive
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1. Align the tabs on the optical-drive bezel with the slots on the optical drive and snap the optical-drive bezel into place.
2. Align the screw holes on the optical-drive bracket with the screw holes on the optical drive.
3. Replace the two screws (M2x3) that secure the optical-drive bracket to the optical drive.
4. Slide the optical-drive assembly into the optical-drive bay.
5. Align the screw hole on the optical-drive bracket with the screw hole on the base cover, then replace the screw (M2x3) that secures
the optical-drive assembly to the palm-rest and keyboard assembly.
7
Replacing the optical drive 19
20 Replacing the optical drive
Removing the base cover
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
Remove the optical drive.
Procedure
1. Remove the five screws (M2.5x6) that secure the base cover to the palm-rest and keyboard assembly.
2. Loosen the four captive screws on the base cover.
3. Remove the two screws (M1.2x1.2) that secure the base cover to the palm-rest and keyboard assembly.
4. Using a plastic scribe, pry the base cover starting from notches located at the top-left corner of the computer base.
5. Lift the base cover off the palm-rest and keyboard assembly.
8
Removing the base cover 21
NOTE: The following steps are applicable only if you want to further remove any other components from your
computer.
6. Disconnect the battery cable from the system board.
22 Removing the base cover
7. Press and hold the power button for 5 seconds to ground the computer and drain the flea power.
Removing the base cover 23
Replacing the base cover
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1. Connect the battery cable to the system board, if applicable.
2. Place the base cover on the palm-rest and keyboard assembly, and snap the base cover into place.
9
24 Replacing the base cover
3. Tighten the four captive screws that secure the base cover to the palm-rest and keyboard assembly.
4. Replace the five screws (M2.5x6) that secure the base cover to the palm-rest and keyboard assembly.
5. Replace the two screws (M1.2x1.2) that secure the base cover to the palm-rest and keyboard assembly.
Replacing the base cover 25
Removing the battery
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Lithium-ion battery precautions
CAUTION:
• Exercise caution when handling Lithium-ion batteries.
• Discharge the battery as much as possible before removing it from the system. This can be done by disconnecting
the AC adapter from the system to allow the battery to drain.
• Do not crush, drop, mutilate, or penetrate the battery with foreign objects.
• Do not expose the battery to high temperatures, or disassemble battery packs and cells.
• Do not apply pressure to the surface of the battery.
• Do not bend the battery.
• Do not use tools of any kind to pry on or against the battery.
• Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental puncture or
damage to the battery and other system components.
• If a battery gets stuck in a device as a result of swelling, do not try to free it as puncturing, bending, or crushing a
Lithium-ion battery can be dangerous. In such an instance, contact for assistance and further instructions.
• If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing, bending,
or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical support for
assistance. See www.dell.com/contactdell.
• Always purchase genuine batteries from www.dell.com or authorized Dell partners and resellers.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
Procedure
1. Disconnect the battery cable from the system board.
NOTE: This step is applicable if the battery cable was not previously disconnected.
2. Remove the four screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.
3. Lift the battery off the palm-rest and keyboard assembly.
10
Removing the battery 27
28 Removing the battery
Replacing the battery
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Lithium-ion battery precautions
CAUTION:
• Exercise caution when handling Lithium-ion batteries.
• Discharge the battery as much as possible before removing it from the system. This can be done by disconnecting
the AC adapter from the system to allow the battery to drain.
• Do not crush, drop, mutilate, or penetrate the battery with foreign objects.
• Do not expose the battery to high temperatures, or disassemble battery packs and cells.
• Do not apply pressure to the surface of the battery.
• Do not bend the battery.
• Do not use tools of any kind to pry on or against the battery.
• Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental puncture or
damage to the battery and other system components.
• If a battery gets stuck in a device as a result of swelling, do not try to free it as puncturing, bending, or crushing a
Lithium-ion battery can be dangerous. In such an instance, contact for assistance and further instructions.
• If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing, bending,
or crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical support for
assistance. See www.dell.com/contactdell.
• Always purchase genuine batteries from www.dell.com or authorized Dell partners and resellers.
Procedure
1. Align the screw holes on the battery with the screw holes on the palm-rest and keyboard assembly.
2. Replace the four screws (M2x3) that secure the battery to the palm-rest and keyboard assembly.
3. Connect the battery cable to the system board.
11
Replacing the battery 29
Removing the memory modules
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Removing the speakers
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
Procedure
1. Disconnect the speaker cable from the system board.
2. Note the speaker cable routing and remove it from the routing guides on palm-rest and key board assembly.
3. Lift the left and right speaker, along with the cable, off the palm-rest and keyboard assembly.
12
Removing the memory modules 31
Procedure
NOTE: Depending on the configuration ordered, your computer may come installed with one or two memory modules.
1. Locate the memory module(s) on your computer.
32 Removing the memory modules
2. Use your fingertips to carefully spread apart the securing-clips on each end of the memory-module slot until the memory module pops
up.
3. Remove the memory module from the memory-module slot.
Removing the memory modules 33
Replacing the memory modules
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
NOTE: Depending on the configuration ordered, your computer may come installed with one or two memory modules.
1. Align the notch on the memory module with the tab on the memory-module slot.
2. Slide the memory module firmly into the slot at an angle.
3. Press the memory module down until it clicks into place.
NOTE: If you do not hear the click, remove the memory module and reinstall it.
Replacing the speakers
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
NOTE: If the rubber grommets are pushed out when removing the speakers, push them back in before replacing the
speakers.
1. Using the alignment posts and rubber grommets, place the left and right speakers in the slots on the palm-rest and keyboard
assembly.
2. Route the speaker cable through the routing guides on the palm-rest and keyboard assembly.
3. Connect the speaker cable to the system board.
13
34 Replacing the memory modules
Removing the wireless card
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
Procedure
1. Locate the wireless card on your computer.
2. Remove the screw (M2x3) that secures the wireless-card bracket to the system board.
3. Slide and remove the wireless-card bracket from the wireless card.
4. Using a plastic scribe, disconnect the antenna cables from the wireless card.
5. Slide and remove the wireless card from the wireless-card slot.
14
36 Removing the wireless card
Removing the wireless card 37
Replacing the wireless card
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
CAUTION: To avoid damage to the wireless card, do not place any cables under it.
1. Align the notch on the wireless card with the tab on the wireless-card slot.
2. Insert the wireless card at an angle into the wireless-card slot.
3. Connect the antenna cables to the wireless card.
The following table provides the antenna-cable color scheme for the wireless card supported by your computer.
Table 2. Antenna-cable color scheme
Connectors on the wireless card Antenna-cable color
Main (white triangle) White
Auxiliary (black triangle) Black
4. Slide and replace the wireless-card bracket on the wireless-card.
5. Replace the screw (M2x3) that secures the wireless-card bracket to the wireless card and the palm-rest and keyboard assembly.
Post-requisites
1. Replace the base cover.
2. Replace the optical drive.
15
38 Replacing the wireless card
Removing the optical-drive connector board
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1. Lift the latch and disconnect the optical-drive connector-board cable from the system board.
2. Remove the two screws (M2x2) that secure the optical-drive connector board to the palm-rest and keyboard assembly.
3. Lift the optical-drive connector board along with the cable off the palm-rest and keyboard assembly.
16
Removing the optical-drive connector board 39
Replacing the optical-drive connector board
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1. Align the screw hole on the optical-drive connector board with the screw hole on the palm-rest and keyboard assembly.
2. Replace the two screws (M2x2) that secure the optical-drive connector board to the palm-rest and keyboard assembly.
3. Connect the optical-drive connector-board cable to the system board and close the latch that secures the optical-drive connector-
board cable to the system board.
17
40 Replacing the optical-drive connector board
Removing the fan
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1. Remove the display cable from the routing guides on the fan.
2. Disconnect the fan cable from the system board.
3. Remove the two screws (M2x3) that secure the fan to the palm-rest and keyboard board assembly.
4. Lift the fan off the palm-rest and keyboard board assembly.
18
Removing the fan 41
Replacing the fan
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1. Align the screw holes on the fan with the screw holes on the palm-rest and keyboard board assembly.
2. Replace the two screws (M2x3) that secure the fan to the palm-rest and keyboard board assembly.
3. Connect the fan cable to the system board.
4. Route the display cable through the routing guides on the fan.
19
42 Replacing the fan
Removing the coin-cell battery
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
CAUTION: Removing the coin-cell battery resets the BIOS setup program’s settings to default. It is recommended that
you note the BIOS setup program’s settings before removing the coin-cell battery.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
Procedure
CAUTION: Removing the coin-cell battery resets the BIOS setup program’s settings to default. Before removing the
coin-cell battery, it is recommended to note the BIOS setup program’s settings.
1. Locate the coin-cell battery socket on the I/O board.
2. Using a plastic scribe, gently pry the coin-cell battery out of the battery socket on the I/O board.
20
Removing the coin-cell battery 43
Replacing the coin-cell battery
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
With the positive-side facing up, snap the coin-cell battery into the battery socket on the I/O board.
Post-requisites
1. Replace the base cover.
2. Replace the optical drive.
21
44 Replacing the coin-cell battery
Removing the solid-state drive/Intel Optane
memory module
You need to disable the Intel Optane memory before removing Intel Optane memory module from your computer. For more information
about disabling the Intel Optane memory, see Disabling Intel Optane memory.
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
NOTE: The M.2 card slot on your computer may support the following configurations:
• M.2 2230 solid-state drive
• M.2 2280 solid-state drive
• M.2 2280 Intel Optane
NOTE: Depending on the configuration installed, a thermal shield may be installed in your computer. If no thermal shield
is installed, skip steps 1 and 2.
1. Remove the screw that secures the thermal shield to the palm-rest and keyboard assembly.
2. Lift the thermal shield off the solid-state drive/Intel Optane.
3. Remove the screw (M2x3) that secures the solid-state drive/Intel Optane to the palm-rest and keyboard assembly.
22
Removing the solid-state drive/Intel Optane memory module 45
4. Lift the solid-state drive/Intel Optane at an angle and remove it from the solid-state drive/Intel Optane slot.
46 Removing the solid-state drive/Intel Optane memory module
Replacing the solid-state drive/Intel Optane
memory module
Enable the Intel Optane memory after you replace the Intel Optane memory module. For more information about enabling the Intel Optane
memory, see Enabling Intel Optane memory.
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
CAUTION: Solid-state drives are fragile. Exercise care when handling the solid-state drive.
Procedure to move the M.2 screw mount
This computer supports two M.2 card form factors:
• M.2 2230
• M.2 2280
If you are replacing the M.2 card with a different form factor, perform the following procedure to move the M.2 screw mount to another
location that accommodates the new form factor. If the replacement card is of the same form factor as the one previously installed, skip
this procedure.
1. Remove the screw (M2x3) that secures the M.2 screw mount to the palm-rest and keyboard assembly.
2. Lift the M.2 screw mount out of the slot on the palm-rest and keyboard assembly.
3. Turn the screw mount 180 degrees.
4. Place the M.2 screw mount into the other slot on the palm-rest and keyboard assembly.
5. Replace the screw (M2x3) that secures the M.2 screw mount to the palm-rest and keyboard assembly.
23
Replacing the solid-state drive/Intel Optane memory module 47
Procedure
NOTE: The M.2 card slot on your computer may support the following configurations:
• M.2 2230 solid-state drive
• M.2 2280 solid-state drive
• M.2 2280 Intel Optane
NOTE: Depending on the configuration installed a thermal shield may be installed in your computer. If no thermal shield
is installed skip steps 4 and 5.
1. Align the notch on the solid-state drive/Intel Optane with the tab on the solid-state drive/Intel Optane slot.
2. Slide the solid-state drive/Intel Optane into the solid-state drive/Intel Optane slot.
3. Replace the screw (M2x3) that secures the solid-state drive/Intel Optane to the palm-rest and keyboard assembly
48 Replacing the solid-state drive/Intel Optane memory module
NOTE: If available, replace the thermal shield after replacing the solid-state drive/Intel Optane.
4. Align the screw hole on the thermal shield with the screw hole on the palm-rest and keyboard assembly.
5. Replace the screw (M2x3) that secures the thermal shield to the palm-rest and keyboard assembly.
Replacing the solid-state drive/Intel Optane memory module 49
50 Replacing the solid-state drive/Intel Optane memory module
Removing the hard drive
If your computer is using a SATA storage device accelerated by Intel Optane memory, disable Intel Optane before removing the SATA
storage device. For more information about disabling the Intel Optane, see Disabling Intel Optane.
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
CAUTION: Hard drives are fragile. Exercise care when handling the hard drive.
CAUTION: To avoid data loss, do not remove the hard drive while the computer is in sleep or on state.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
3. Remove the battery.
Procedure
1. Open the latch and disconnect the hard-drive cable from the system board.
2. Remove the three screws (M2x3) that secure the hard-drive assembly to the palm-rest and keyboard assembly.
3. Lift the hard-drive assembly along with its cable off the palm-rest and keyboard assembly.
24
Removing the hard drive 51
4. Disconnect the interposer from the hard-drive assembly.
5. Remove the four screws (M3x3) that secure the hard-drive bracket to the hard drive.
6. Lift the hard-drive bracket off the hard drive.
52 Removing the hard drive
Replacing the hard drive
Enable Intel Optane after replacing the SATA storage. For more information about enabling the Intel Optane, see Enabling Intel Optane.
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
CAUTION: Hard drives are fragile. Exercise care when handling the hard drive.
Procedure
1. Align the screw holes on the hard-drive bracket with the screw holes on the hard drive.
2. Replace the four screws (M3x3) that secure the hard-drive bracket to the hard drive.
3. Connect the interposer to the hard-drive assembly.
25
Replacing the hard drive 53
4. Align the screw holes on the hard-drive assembly with the screw holes on the palm-rest and keyboard assembly.
5. Replace the three screws (M2x3) that secure the hard-drive assembly to the palm-rest and keyboard assembly.
6. Connect the hard-drive cable to the system board and close the latch to secure the cable.
Post-requisites
1. Replace the battery.
2. Replace the base cover.
3. Replace the optical drive.
54 Replacing the hard drive
Removing the speakers
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
Procedure
1. Disconnect the speaker cable from the system board.
2. Note the speaker cable routing and remove it from the routing guides on palm-rest and key board assembly.
3. Lift the left and right speaker, along with the cable, off the palm-rest and keyboard assembly.
26
Removing the speakers 55
Replacing the speakers
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
NOTE: If the rubber grommets are pushed out when removing the speakers, push them back in before replacing the
speakers.
1. Using the alignment posts and rubber grommets, place the left and right speakers in the slots on the palm-rest and keyboard
assembly.
2. Route the speaker cable through the routing guides on the palm-rest and keyboard assembly.
3. Connect the speaker cable to the system board.
Post-requisites
1. Replace the base cover.
2. Replace the optical drive.
27
56 Replacing the speakers
Removing the touchpad
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
3. Remove the battery.
Procedure
1. Open the latch and disconnect the I/O-board cable from the system board.
2. Lift the I/O-board cable off the touchpad.
3. Peel the tape that secures the touchpad bracket to the palm-rest and keyboard assembly.
4. Remove the three (M2x2) screws that secure the touchpad bracket to the palm-rest and keyboard assembly.
5. Lift the touchpad bracket off the palm-rest and keyboard assembly.
6. Open the latch and disconnect the touchpad cable from the touchpad.
7. Peel the tape that secures the touchpad to the palm-rest and keyboard assembly
8. Remove the four screws (M2x2) that secure the touchpad to the palm-rest and keyboard assembly.
9. Slide and lift the touchpad off the palm-rest and keyboard assembly.
28
Removing the touchpad 57
58 Removing the touchpad
Replacing the touchpad
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
NOTE: Ensure that the touchpad is aligned with the guides available on the palm-rest and keyboard assembly, and the
gap on either sides of the touchpad is equal.
1. Slide and place the touchpad into the slot on the palm-rest and keyboard assembly.
2. Replace the four screws (M2x2) that secure the touchpad to the palm-rest and keyboard assembly.
3. Adhere the tape that secures the touchpad to the palm-rest and keyboard assembly.
4. Align the screw holes on the touchpad bracket to the screw holes on the palm-rest and keyboard assembly.
5. Replace the three screws (M2x2) that secure the touchpad bracket to the palm-rest and keyboard assembly.
6. Slide the touchpad cable into the touchpad connector on the touchpad and close the latch to secure the cable.
7. Adhere the tape that secures the touchpad bracket to the palm-rest and keyboard assembly.
8. Place the I/O-board cable onto the touchpad.
9. Slide the I/O-board cable into the connector on the system board and close the latch to secure the cable.
29
Replacing the touchpad 59
Removing the heat sink
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
NOTE: The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you
touch it.
CAUTION: For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils in your
skin can reduce the heat transfer capability of the thermal grease.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
3. Remove the fan.
Procedure
NOTE: Depending on the configuration ordered, the number of captive screws on the heat sink may vary:
• Computers with discrete graphics: 7 captive screws
• Computers without discrete graphics: 4 captive screws
1. In sequential order (1->2->3->4->...), loosen the captive screws that secure the heat sink to the system board.
2. Lift the heat sink off the system board.
30
Removing the heat sink 61
62 Removing the heat sink
Replacing the heat sink
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
CAUTION: Incorrect alignment of the heat sink can damage the system board and processor.
NOTE: If either the system board or the heat sink is replaced, use the thermal pad/paste provided in the kit to ensure
that thermal conductivity is achieved.
Procedure
NOTE: Depending on the configuration ordered, the number of captive screws on the heat sink may vary:
• Computers with discrete graphics: 7 captive screws
• Computers without discrete graphics: 4 captive screws
1. Place the heat sink on the system board and align the screw holes on the heat sink with the screw holes on the system board.
2. Tighten the captive screws in the reverse order (...->4->3->2->1) to secure the heat sink to the system board.
Post-requisites
1. Replace the fan.
31
Replacing the heat sink 63
Removing the power-adapter port
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Removing the display assembly
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
3. Remove the wireless card.
Procedure
1. Lift the latch and disconnect the optical-drive connector-board cable from the optical-drive board connector.
2. Peel the tape that secures the display-cable connector latch to the system board.
3. Open the latch and disconnect the display cable from the system board.
4. Note the routing of the display cable and remove the cable from its routing guides on the fan and palm-rest and keyboard assembly.
5. Remove the six screws (M2.5x5) that secure the left and right hinges to the system board and palm-rest and keyboard assembly.
6. Open the hinges.
32
Removing the power-adapter port 65
7. Lift the palm-rest and keyboard assembly at an angle.
8. Slide and remove the palm-rest and keyboard assembly off the display assembly.
66 Removing the power-adapter port
9. After performing all the above steps, you are left with display assembly.
Removing the power-adapter port 67
Procedure
1. Remove the four screws (M2.5x5) that secure the right hinge to the system board and palm-rest and keyboard assembly.
2. Lift the right hinge.
3. Disconnect the power-adapter port cable from the system board.
4. Remove the screw (M2x3) that secures the power-adapter port to the palm-rest and keyboard assembly.
5. Lift the power-adapter port, along with its cable, off the palm-rest and keyboard assembly.
68 Removing the power-adapter port
Removing the power-adapter port 69
Replacing the power-adapter port
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1. Align the screw hole on the power-adapter port with the screw hole on the palm-rest and keyboard assembly.
2. Replace the screw (M2x3) that secures the power-adapter port to the palm-rest and keyboard assembly.
3. Connect the power-adapter port cable to the system board.
4. Close the right hinge.
5. Replace the four screws (M2.5x5) that secure the right hinge to the system board and palm-rest assembly.
33
70 Replacing the power-adapter port
Replacing the display assembly
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
NOTE: Ensure that the hinges are opened to the maximum before replacing the display assembly on palm-rest and
keyboard assembly.
1. Slide the palm-rest and keyboard assembly under the hinges on the display assembly
2. Place and align the palm-rest and keyboard assembly on the display assembly.
Replacing the power-adapter port 71
3. Using the alignment posts, press the hinges down on the system board and the palm-rest and keyboard assembly.
4. Replace the six screws (M2x2.5) that secure the left and right hinges to the system board and palm-rest and keyboard assembly.
5. Route the display cable through the routing guides on the fan and the palm-rest and keyboard assembly.
6. Slide the display cable to the connector on the system board and close the latch to secure the cable.
7. Replace the tape that secures the display-cable latch to the system board.
8. Connect the optical-drive connector board cable to the optical-drive board.
72 Replacing the power-adapter port
Removing the I/O board
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
CAUTION: Disconnecting the I/O board resets the BIOS setup program’s settings to default. Before disconnecting the
I/O board, it is recommended to note the BIOS setup program’s settings.
1. Remove the optical drive.
2. Remove the base cover.
3. Remove the battery.
4. Remove the hard drive.
Procedure
CAUTION: Disconnecting the I/O board resets the BIOS setup program’s settings to default. Before disconnecting the
I/O board, it is recommended to note the BIOS setup program’s settings.
1. Open the latch and disconnect the I/O-board cable from the system board.
2. Lift the I/O board, along with the cable, off the palm-rest and keyboard assembly.
34
74 Removing the I/O board
Removing the I/O board 75
Replacing the I/O board
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1. Using the alignment posts, place the I/O board on the palm-rest and keyboard assembly.
2. Adhere the I/O-board cable to the palm-rest and keyboard assembly.
3. Connect the I/O-board cable to the system board and close the latch to secure the cable.
Post-requisites
1. Replace the hard drive.
2. Replace the battery.
3. Replace the base cover.
4. Replace the optical drive.
35
76 Replacing the I/O board
Removing the power-button board
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1. Remove the base cover.
2. Remove the fan.
Procedure
1. Remove the display cable from the routing guides on the fan, palm-rest and keyboard assembly and left hinge.
2. Remove the two screws (M2.5x5) that secure the display assembly to the palm-rest and keyboard assembly.
3. Lift the left hinge.
4. Open the latch and disconnect the power-button board cable from the system board.
5. Peel the power-button board cable off the palm-rest and keyboard assembly.
6. Remove the two screws (M2x2) that secure the power-button board.
36
Removing the power-button board 77
7. Lift the power-button board, along with the cable, off the palm-rest and keyboard assembly.
78 Removing the power-button board
Replacing the power-button board
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1. Using the alignment posts, place the power-button board along with its cable onto the palm-rest and keyboard assembly.
2. Replace the two screws (M2x2) that secure the power-button board to the palm-rest and keyboard assembly.
3. Adhere the power-button board cable to the palm-rest and keyboard assembly.
4. Connect the power-button board cable to the system board and close the latch to secure the cable.
5. Close the left hinge.
6. Replace the two screws (M2.5x5) that secure the left hinge to the palm-rest and keyboard assembly.
7. Route the display cable through the routing guides on the fan, palm-rest and keyboard assembly and left hinge.
37
Replacing the power-button board 79
Removing the power button with fingerprint
reader
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
NOTE: Applicable only for computers that are shipped with fingerprint reader.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
3. Remove the battery.
4. Remove the hard drive.
5. Remove the fan.
6. Remove the power-button board.
Procedure
1. Open the latch and disconnect the power-button cable from the system board.
2. Lift the power button, along with its cable, off the palm-rest and keyboard assembly.
38
Removing the power button with fingerprint reader 81
82 Removing the power button with fingerprint reader
Replacing the power button with fingerprint
reader
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
NOTE: Applicable only for computers that are shipped with fingerprint reader.
Procedure
1. Connect the power-button cable to the system board
2. Place the power button with fingerprint reader into the slot on the palm-rest and keyboard assembly.
3. Adhere the power-button cable on the palm-rest and keyboard assembly.
Post-requisites
1. Replace the power-button board.
2. Replace the fan.
3. Replace the hard drive.
39
Replacing the power button with fingerprint reader 83
Removing the display assembly
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
3. Remove the wireless card.
Procedure
1. Lift the latch and disconnect the optical-drive connector-board cable from the optical-drive board connector.
2. Peel the tape that secures the display-cable connector latch to the system board.
3. Open the latch and disconnect the display cable from the system board.
4. Note the routing of the display cable and remove the cable from its routing guides on the fan and palm-rest and keyboard assembly.
5. Remove the six screws (M2.5x5) that secure the left and right hinges to the system board and palm-rest and keyboard assembly.
6. Open the hinges.
40
Removing the display assembly 85
7. Lift the palm-rest and keyboard assembly at an angle.
8. Slide and remove the palm-rest and keyboard assembly off the display assembly.
86 Removing the display assembly
9. After performing all the above steps, you are left with display assembly.
Removing the display assembly 87
Replacing the display assembly
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
NOTE: Ensure that the hinges are opened to the maximum before replacing the display assembly on palm-rest and
keyboard assembly.
1. Slide the palm-rest and keyboard assembly under the hinges on the display assembly
2. Place and align the palm-rest and keyboard assembly on the display assembly.
3. Using the alignment posts, press the hinges down on the system board and the palm-rest and keyboard assembly.
4. Replace the six screws (M2x2.5) that secure the left and right hinges to the system board and palm-rest and keyboard assembly.
5. Route the display cable through the routing guides on the fan and the palm-rest and keyboard assembly.
6. Slide the display cable to the connector on the system board and close the latch to secure the cable.
7. Replace the tape that secures the display-cable latch to the system board.
8. Connect the optical-drive connector board cable to the optical-drive board.
41
88 Replacing the display assembly
Removing the system board
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup
program after you replace the system board.
NOTE: Replacing the system board removes any changes you have made to the BIOS using the BIOS setup program. You
must make the appropriate changes again after you replace the system board.
NOTE: Before disconnecting the cables from the system board, note the location of the connectors so that you can
reconnect the cables correctly after you replace the system board.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
3. Remove the battery.
4. Remove the memory modules.
5. Remove the wireless card.
6. Remove the solid-state drive/Intel Optane.
7. Remove the fan.
8. Remove the heat sink.
Procedure
1. Remove the four screws (M2.5x5) that secure the right hinge to the system board and palm-rest and keyboard assembly.
2. Lift the right hinge.
42
90 Removing the system board
3. Disconnect the power-adapter port cable from the system board.
4. Disconnect the speaker cable from the system board.
5. Open the latch and disconnect the keyboard from the system board.
6. Open the latch and disconnect the touchpad cable from the system board.
7. Open the latch and disconnect the hard-drive cable from the system board.
8. Open the latch and disconnect the optical-drive connector-board cable.
9. Open the latch and disconnect the I/O board cable from the system board.
10. Open the latch and disconnect the power-button board cable from the system board.
11. Open the latch and disconnect the fingerprint reader cable from the system board.
NOTE: Skip this step if your computer was shipped without a fingerprint reader installed.
Removing the system board 91
12. Remove the two screws (M2x2) that secure the system board to palm-rest and keyboard assembly.
13. Remove the two screws (M2x3) that secure the system board to palm-rest and keyboard assembly.
14. Lift the system board off the palm-rest and keyboard assembly.
92 Removing the system board
Removing the system board 93
Replacing the system board
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup
program after you replace the system board.
NOTE: Replacing the system board removes any changes you have made to the BIOS using the BIOS setup program. You
must make the appropriate changes again after you replace the system board.
Procedure
1. Align the screw holes on the system board with the screw holes on the palm-rest and keyboard assembly.
2. Replace the two screws (M2x3) that secure the system board to the palm-rest and keyboard assembly.
3. Replace the two screws (M2x2) that secure the system board to the palm-rest and keyboard assembly.
4. Slide the fingerprint reader cable into the connector on the system board and close the latch.
43
94 Replacing the system board
NOTE: Skip this step if your computer was shipped without a fingerprint reader installed.
5. Slide the power-button board cable into the connector on the system board and close the latch.
6. Slide the I/O board cable into the connector on the system board and close the latch.
7. Slide the optical-drive connector-board cable into the connector on the system board and close the latch.
8. Slide the hard-drive cable into the connector on the system board and close the latch.
9. Slide the touchpad cable into the connector on the system board and close the latch.
10. Slide the keyboard cable into the connector on the system board and close the latch.
11. Connect the speaker cable to the system board.
12. Connect the power-adapter port cable to the system board.
13. Close the right display hinge.
14. Replace the four screws (M2.5x5) that secure the right hinge to the system board and palm-rest and keyboard assembly.
Replacing the system board 95
Post-requisites
1. Replace the heat sink.
2. Replace the fan.
3. Replace the solid-state drive/Intel Optane.
4. Replace the wireless card.
5. Replace the memory modules.
6. Replace the battery.
7. Replace the base cover.
8. Replace the optical drive.
Entering the Service Tag in the BIOS setup
program
1. Turn on or restart your computer.
2. Press F2 when the Dell logo is displayed to enter the BIOS setup program.
3. Navigate to the Main tab and enter the Service Tag in the Service Tag Input field.
NOTE: Service tag is the alphanumeric identifier located at the back side of your computer.
96 Replacing the system board
Removing the palm-rest and keyboard
assembly
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
3. Remove the battery.
4. Remove the optical-drive connector board.
5. Remove the fan.
6. Remove the solid-state drive/Intel Optane.
7. Remove the wireless card.
8. Remove the speakers.
9. Remove the hard drive.
10. Remove the touchpad.
11. Remove the power-adapter port.
12. Remove the display assembly.
13. Remove the I/O board.
14. Remove the power-button board.
15. Remove the system board.
16. Remove the power button with fingerprint reader (optional).
Procedure
After performing the above steps, we are left with the palm-rest and keyboard assembly.
44
Removing the palm-rest and keyboard assembly 97
98 Removing the palm-rest and keyboard assembly
Replacing the palm-rest and keyboard
assembly
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
Place the palm-rest and keyboard assembly on a flat and clean surface.
Post-requisites
1. Replace the power button with fingerprint reader (optional).
2. Replace the system board.
3. Replace the power-button board.
4. Replace the I/O board.
5. Replace the display assembly.
6. Replace the power-adapter port.
45
Replacing the palm-rest and keyboard assembly 99
7. Replace the touchpad.
8. Replace the hard drive.
9. Replace the speakers.
10. Replace the wireless card.
11. Replace the solid-state drive/Intel Optane.
12. Replace the fan.
13. Replace the optical-drive connector board.
14. Replace the battery.
15. Replace the base cover.
16. Replace the optical drive.
100 Replacing the palm-rest and keyboard assembly
Removing the display bezel
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
3. Remove the wireless card.
4. Remove the display assembly.
Procedure
1. Using a plastic scribe, carefully pry up the display bezel from the top-left outer edge of the display back-cover and antenna assembly.
2. Remove the display bezel off the display back-cover and antenna assembly.
46
Removing the display bezel 101
Replacing the display bezel
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
Align the display bezel with the display back-cover and antenna assembly, and then gently snap the display bezel into place.
Post-requisites
1. Replace the display assembly.
2. Replace the wireless card.
3. Replace the base cover.
4. Replace the optical drive.
47
102 Replacing the display bezel
Removing the camera
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
3. Remove the wireless card.
4. Remove the display assembly.
5. Remove the display bezel.
Procedure
1. Gently pry the camera off the display back-cover and antenna assembly.
2. Release the camera cable from the routing guides on the display back-cover and antenna assembly.
3. Peel the tape securing the camera cable to the camera module.
4. Disconnect the camera cable from the camera module.
48
Removing the camera 103
104 Removing the camera
Replacing the camera
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1. Connect the camera cable to the camera module.
2. Adhere the tape that secures the camera cable to the camera module.
3. Using the alignment post adhere the camera module on the display back-cover and antenna assembly.
4. Route the camera cable through the routing guides on the display back-cover and antenna assembly.
Post-requisites
1. Replace the display bezel.
2. Replace the display assembly.
3. Replace the wireless card.
49
Replacing the camera 105
Removing the display panel
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
3. Remove the wireless card.
4. Remove the display assembly.
5. Remove the display bezel.
Procedure
1. Remove the four screws (M2x2.5) that secure the display panel to the display back-cover and antenna assembly.
2. Lift the display panel and turn it over.
50
Removing the display panel 107
3. Peel the tape adhering the display cable to the back of the display panel.
4. Lift the latch and disconnect the display cable from the display-panel cable connector.
5. Lift the display panel away from the display back-cover and antenna assembly.
108 Removing the display panel
Replacing the display panel
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1. Place the display panel on a flat and clean surface.
2. Connect the display cable to the connector at the back of the display panel and close the latch to secure the cable.
3. Adhere the tape that secures the display cable to the back of the display panel.
4. Place the display panel on the display back-cover and antenna assembly and align the screw holes on the display panel with the screw
holes on the display bac-cover and antenna assembly.
5. Replace the four screws (M2x2) that secure the display panel to the display back-cover and antenna assembly.
51
Replacing the display panel 109
Removing the display hinges
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
3. Remove the wireless card.
4. Remove the display assembly.
5. Remove the display bezel.
6. Remove the display panel.
Procedure
1. Remove the eight screws (M2x2) that secure the display-hinge brackets to the display back-cover and antenna assembly.
2. Lift the display hinges and brackets off the display back-cover and antenna assembly.
52
Removing the display hinges 111
112 Removing the display hinges
Replacing the display hinges
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
1. Align the screw holes on the display hinges and brackets with the screw holes on the display back-cover and antenna assembly.
2. Replace the eight screws (M2x2) that secure the display-hinge brackets to the display back-cover and antenna assembly.
Post-requisites
1. Replace the display panel.
2. Replace the display bezel.
3. Replace the display assembly.
4. Replace the wireless card.
53
Replacing the display hinges 113
Removing the display cable
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
3. Remove the wireless card.
4. Remove the display assembly.
5. Remove the display bezel.
6. Remove the display panel.
7. Remove the camera.
Procedure
1. Note the display cable routing and remove the cable from the routing guides on the display back-cover and antenna assembly.
2. Remove the display cable from the display back-cover and antenna assembly.
54
Removing the display cable 115
Replacing the display cable
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
Route the display cable through the routing guides on the display back-cover and antenna assembly.
Post-requisites
1. Replace the camera.
2. Replace the display panel.
3. Replace the display bezel.
4. Replace the display assembly.
5. Replace the wireless card.
6. Replace the base cover.
7. Replace the optical drive.
55
116 Replacing the display cable
Removing the display back-cover and antenna
assembly
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Prerequisites
1. Remove the optical drive.
2. Remove the base cover.
3. Remove the wireless card.
4. Remove the display assembly.
5. Remove the display bezel.
6. Remove the camera.
7. Remove the display panel.
8. Remove the display hinges.
9. Remove the display cable.
Procedure
After performing all the above steps, we are left with the display back-cover and antenna assembly.
56
Removing the display back-cover and antenna assembly 117
118 Removing the display back-cover and antenna assembly
Replacing the display back-cover and antenna
assembly
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow
the steps in Before working inside your computer. After working inside your computer, follow the instructions in After
working inside your computer. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/regulatory_compliance.
Procedure
Place the display back-cover and antenna assembly on a clean and flat surface.
Post-requisites
1. Replace the display cable.
2. Replace the display hinges.
3. Replace the display panel.
4. Replace the camera.
5. Replace the display bezel.
6. Replace the display assembly.
57
Replacing the display back-cover and antenna assembly 119
Device drivers
Intel Chipset Software Installation Utility
In the Device Manager, check if the chipset driver is installed.
Install the Intel chipset updates from www.dell.com/support.
Video drivers
In the Device Manager, check if the video driver is installed.
Install the video driver update from www.dell.com/support.
Intel Serial IO driver
In the Device Manager, check if the Intel Serial IO driver is installed.
Install the driver updates from www.dell.com/support.
Intel Trusted Execution Engine Interface
In the Device Manager, check if the Intel Trusted Execution Engine Interface driver is installed.
Install the driver update from www.dell.com/support.
Intel Virtual Button driver
In the Device Manager, check if the Intel Virtual Button driver is installed.
Install the driver updates from www.dell.com/support.
Wireless and Bluetooth drivers
In the Device Manager, check if the network card driver is installed.
Install the driver updates from www.dell.com/support.
In the Device Manager, check if the Bluetooth driver is installed.
Install the driver updates from www.dell.com/support.
58
Device drivers 121
System setup
NOTE: Depending on the computer and its installed devices, the items listed in this section may or may not be displayed.
System setup
CAUTION: Unless you are an expert computer user, do not change the settings in the BIOS Setup program. Certain
changes can make your computer work incorrectly.
NOTE: Before you change BIOS Setup program, it is recommended that you write down the BIOS Setup program screen
information for future reference.
Use the BIOS Setup program for the following purposes:
• Get information about the hardware installed in your computer, such as the amount of RAM and the size of the hard drive.
• Change the system configuration information.
• Set or change a user-selectable option, such as the user password, type of hard drive installed, and enabling or disabling base devices.
Entering BIOS setup program
1. Turn on (or restart) your computer.
2. During POST, when the DELL logo is displayed, watch for the F2 prompt to appear, and then press F2 immediately.
NOTE: The F2 prompt indicates that the keyboard is initialized. This prompt can appear very quickly, so you must
watch for it, and then press F2. If you press F2 before the F2 prompt, this keystroke is lost. If you wait too long and
the operating system logo appears, continue to wait until you see the desktop. Then, turn off your computer and try
again.
Navigation keys
NOTE: For most of the System Setup options, changes that you make are recorded but do not take effect until you
restart the system.
Keys Navigation
Up arrow Moves to the previous field.
Down arrow Moves to the next field.
Enter Selects a value in the selected field (if applicable) or follow the link in the field.
Spacebar Expands or collapses a drop-down list, if applicable.
Tab Moves to the next focus area.
NOTE: For the standard graphics browser only.
Esc Moves to the previous page until you view the main screen. Pressing Esc in the main screen displays a message
that prompts you to save any unsaved changes and restarts the system.
Boot Sequence
Boot Sequence allows you to bypass the System Setup–defined boot device order and boot directly to a specific device (for example:
optical drive or hard drive). During the Power-on Self Test (POST), when the Dell logo appears, you can:
• Access System Setup by pressing F2 key
59
122 System setup
• Bring up the one-time boot menu by pressing F12 key
The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot menu options are:
• Removable Drive (if available)
• STXXXX Drive
NOTE: XXX denotes the SATA drive number.
• Optical Drive (if available)
• SATA Hard Drive (if available)
• Diagnostics
NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.
The boot sequence screen also displays the option to access the System Setup screen.
Clearing CMOS settings
CAUTION: Clearing CMOS settings will reset the BIOS settings on your computer.
1. Remove the base cover.
2. Disconnect the battery cable from the system board.
3. Remove the coin-cell battery.
4. Wait for one minute.
5. Replace the coin-cell battery.
6. Connect the battery cable to the system board.
7. Replace the base cover.
Clearing BIOS (System Setup) and System
passwords
To clear the system or BIOS passwords, contact Dell technical support as described at www.dell.com/contactdell.
NOTE: For information on how to reset Windows or application passwords, refer to the documentation accompanying
Windows or your application.
System setup 123
Troubleshooting
Flashing the BIOS
You may need to flash (update) the BIOS when an update is available or when you replace the system board.
Follow these steps to flash the BIOS:
1. Turn on your computer.
2. Go to www.dell.com/support.
3. Click Product support, enter the Service Tag of your computer, and then click Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.
4. Click Drivers & downloads > Find it myself.
5. Select the operating system installed on your computer.
6. Scroll down the page and expand BIOS.
7. Click Download to download the latest version of the BIOS for your computer.
8. After the download is complete, navigate to the folder where you saved the BIOS update file.
9. Double-click the BIOS update file icon and follow the instructions on the screen.
Flashing BIOS (USB key)
1. Follow the procedure from step 1 to step 7 in "Flashing the BIOS" to download the latest BIOS setup program file.
2. Create a bootable USB drive. For more information see the knowledge base article SLN143196 at www.dell.com/support.
3. Copy the BIOS setup program file to the bootable USB drive.
4. Connect the bootable USB drive to the computer that needs the BIOS update.
5. Restart the computer and press F12 when the Dell logo is displayed on the screen.
6. Boot to the USB drive from the One Time Boot Menu.
7. Type the BIOS setup program filename and press Enter.
8. The BIOS Update Utility appears. Follow the instructions on the screen to complete the BIOS update.
Enhanced Pre-Boot System Assessment (ePSA)
diagnostics
CAUTION: Use the ePSA diagnostics to test only your computer. Using this program with other computers may cause
invalid results or error messages.
The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware. The ePSA is embedded with the
BIOS and is launched by the BIOS internally. The embedded system diagnostics provides a set of options for particular devices or device
groups allowing you to:
• Run tests automatically or in an interactive mode
• Repeat tests
• Display or save test results
• Run thorough tests to introduce additional test options to provide extra information about the failed device(s)
• View status messages that inform you if tests are completed successfully
• View error messages that inform you of problems encountered during testing
NOTE: Some tests for specific devices require user interaction. Always ensure that you are present at the computer
terminal when the diagnostic tests are performed.
60
124 Troubleshooting
Running the ePSA diagnostics
1. Turn on your computer.
2. As the computer boots, press the F12 key as the Dell logo appears.
3. On the boot menu screen, select the Diagnostics option.
4. Click the arrow at the bottom left corner.
Diagnostics front page is displayed.
5. Click the arrow in the lower-right corner to go to the page listing.
The items detected are listed.
6. To run a diagnostic test on a specific device, press Esc and click Yes to stop the diagnostic test.
7. Select the device from the left pane and click Run Tests.
8. If there are any issues, error codes are displayed.
Note the error code and validation number and contact Dell.
System diagnostic lights
Battery-status light
Indicates the power and battery-charge status.
Solid white — Power adapter is connected and the battery has more than 5 percent charge.
Amber — Computer is running on battery and the battery has less than 5 percent charge.
Off
• Power adapter is connected and the battery is fully charged.
• Computer is running on battery and the battery has more than 5 percent charge.
• Computer is in sleep state, hibernation, or turned off.
The power and battery-status light blinks amber along with beep codes indicating failures.
For example, the power and battery-status light blinks amber two times followed by a pause, and then blinks white three times followed by
a pause. This 2,3 pattern continues until the computer is turned off indicating no memory or RAM is detected.
The following table shows different power and battery-status light patterns and associated problems.
Table 3. LED codes
Diagnostic light codes Problem description
2,1 Processor failure
2,2 System board: BIOS or ROM (Read-Only Memory) failure
2,3 No memory or RAM (Random-Access Memory) detected
2,4 Memory or RAM (Random-Access Memory) failure
2,5 Invalid memory installed
2,6 System-board or chipset error
2,7 Display failure
3,1 Coin-cell battery failure
3,2 PCI, video card/chip failure
3,3 Recovery image not found
3,4 Recovery image found but invalid
3,5 Power-rail failure
3,6 System BIOS Flash incomplete
3,7 Management Engine (ME) error
Camera status light: Indicates whether the camera is in use.
• Solid white — Camera is in use.
Troubleshooting 125
• Off — Camera is not in use.
Caps Lock status light: Indicates whether Caps Lock is enabled or disabled.
• Solid white — Caps Lock enabled.
• Off — Caps Lock disabled.
Enabling Intel Optane memory
1. On the taskbar, click the search box, and then type Intel Rapid Storage Technology.
2. Click Intel Rapid Storage Technology.
The Intel Rapid Storage Technology window is displayed.
3. On the Status tab, click Enable to enable the Intel Optane memory.
4. On the warning screen, select a compatible fast drive, and then click Yes to continue enabling Intel Optane memory.
5. Click Intel Optane memory > Reboot to complete enabling your Intel Optane memory.
NOTE: Applications may take up to three subsequent launches after enablement to see the full performance
benefits.
Disabling Intel Optane memory
CAUTION: After disabling Intel Optane memory, do not uninstall the driver for Intel Rapid Storage Technology as it will
result in a blue screen error. The Intel Rapid Storage Technology user interface can be removed without uninstalling the
driver.
NOTE: Disabling Intel Optane memory is required before removing the SATA storage device accelerated by the Intel
Optane memory module from the computer.
1. On the taskbar, click the search box, and then type Intel Rapid Storage Technology.
2. Click Intel Rapid Storage Technology.
The Intel Rapid Storage Technology window is displayed.
3. On the Intel Optane memory tab, click Disable to disable the Intel Optane memory.
NOTE: For computers in which Intel Optane memory acts as a primary storage, do not disable the Intel Optane
memory. The Disable option will be grayed out.
4. Click Yes if you accept the warning.
The disabling progress is displayed.
5. Click Reboot to complete disabling your Intel Optane memory and restart your computer.
WiFi power cycle
If your computer is unable to access the internet due to WiFi connectivity issues a WiFi power cycle procedure may be performed. The
following procedure provides the instructions on how to conduct a WiFi power cycle:
NOTE: Some ISPs (Internet Service Providers) provide a modem/router combo device.
1. Turn off your computer.
2. Turn off the modem.
3. Turn off the wireless router.
4. Wait for 30 seconds.
5. Turn on the wireless router.
6. Turn on the modem.
7. Turn on your computer.
Flea power release
Flea power is the residual static electricity that remains on the computer even after it has been powered off and the battery has been
removed. The following procedure provides the instructions on how to conduct flea power release:
126 Troubleshooting
1. Turn off your computer.
2. Disconnect the power adapter from your computer.
3. Press and hold the power button for 15 seconds to drain the flea power.
4. Connect the power adapter to your computer.
5. Turn on your computer.
Troubleshooting 127
Getting help and contacting Dell
Self-help resources
You can get information and help on Dell products and services using these self-help resources:
Table 4. Self-help resources
Self-help resources Resource location
Information about Dell products and services www.dell.com
My Dell app
Tips
Contact Support In Windows search, type Contact Support, and press Enter.
Online help for operating system www.dell.com/support/windows
Troubleshooting information, user manuals, setup instructions,
product specifications, technical help blogs, drivers, software
updates, and so on.
www.dell.com/support
Dell knowledge base articles for a variety of computer concerns. 1. Go to www.dell.com/support.
2. Type the subject or keyword in the Search box.
3. Click Search to retrieve the related articles.
Learn and know the following information about your product:
• Product specifications
• Operating system
• Setting up and using your product
• Data backup
• Troubleshooting and diagnostics
• Factory and system restore
• BIOS information
See Me and My Dell at www.dell.com/support/manuals.
To locate the Me and My Dell relevant to your product, identify
your product through one of the following:
• Select Detect Product.
• Locate your product through the drop-down menu under View
Products.
• Enter the Service Tag number or Product ID in the search
bar.
Contacting Dell
To contact Dell for sales, technical support, or customer service issues, see www.dell.com/contactdell.
NOTE: Availability varies by country/region and product, and some services may not be available in your country/region.
NOTE: If you do not have an active internet connection, you can find contact information on your purchase invoice,
packing slip, bill, or Dell product catalog.
61
128 Getting help and contacting Dell