Dell OptiPlex 7020 Mini Tower Owner's Manual
Working on Your Computer
Removing and Installing Components
System Setup
Diagnostics
- Enhanced Pre-Boot System Assessment (ePSA) Diagnostics
Troubleshooting Your Computer
Specifications
Contacting Dell

DELL 7020 User Manual

Displayed below is the user manual for 7020 by DELL which is a product in the PCs/Workstations category. This manual has pages.

Related Manuals

DELL 7020 Manual

ZAGG GEAR4 D3O CRYSTAL PALACE transparent 702005178 Manual

Origin Storage DELL-BDRW-SATA Manual

Dell OptiPlex 7020 Mini Tower

Owner's Manual

Regulatory Model: D13M

Regulatory Type: D13M001

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other

jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.

2014 - 07

Rev. A00

Contents

1 Working on Your Computer................................................................................5

Before Working Inside Your Computer................................................................................................ 5

Turning Off Your Computer..................................................................................................................6

After Working Inside Your Computer................................................................................................... 7

2 Removing and Installing Components............................................................. 8

Recommended Tools............................................................................................................................8

Front and Back View..............................................................................................................................8

Removing the Cover............................................................................................................................. 9

Installing the Cover............................................................................................................................... 9

Removing the Intrusion Switch.............................................................................................................9

Installing the Intrusion Switch.............................................................................................................10

Removing the Wireless Local Area Network (WLAN) Card................................................................10

Installing the Wireless Local Area Network (WLAN) Card.................................................................. 11

Removing the Front Bezel...................................................................................................................12

Installing the Front Bezel.....................................................................................................................12

Removing the Expansion Card............................................................................................................12

Installing the Expansion Card..............................................................................................................13

Memory Module Guidelines................................................................................................................14

Removing the Memory........................................................................................................................14

Installing the Memory..........................................................................................................................14

Removing the Coin-Cell Battery.........................................................................................................15

Installing the Coin-Cell Battery...........................................................................................................15

Removing the Hard Drive....................................................................................................................16

Installing the Hard Drive......................................................................................................................16

Removing the Optical Drive................................................................................................................ 17

Installing the Optical Drive..................................................................................................................18

Removing the Speaker........................................................................................................................ 18

Installing the Speaker.......................................................................................................................... 18

Removing the Power Supply...............................................................................................................19

Installing the Power Supply................................................................................................................ 20

Removing the Heat Sink Assembly.....................................................................................................20

Installing the Heat Sink Assembly....................................................................................................... 21

Removing the Processor..................................................................................................................... 21

Installing the Processor....................................................................................................................... 21

Removing the System Fan.................................................................................................................. 22

Installing the System Fan.................................................................................................................... 23

Removing the Thermal Sensor........................................................................................................... 23

Installing the Thermal Sensor.............................................................................................................24

Removing the Power Switch.............................................................................................................. 24

Installing the Power Switch................................................................................................................ 26

Removing the Input/Output (I/O) Panel............................................................................................ 26

Installing the Input/Output (I/O) Panel.............................................................................................. 28

Removing the System Board.............................................................................................................. 28

Installing the System Board................................................................................................................ 29

System Board Layout.......................................................................................................................... 29

3 System Setup....................................................................................................... 31

Boot Sequence.................................................................................................................................... 31

Navigation Keys................................................................................................................................... 31

System Setup Options.........................................................................................................................32

Updating the BIOS ..............................................................................................................................41

Jumper Settings...................................................................................................................................41

System and Setup Password...............................................................................................................42

Assigning a System Password and Setup Password.................................................................... 42

Deleting or Changing an Existing System and/or Setup Password.............................................43

Disabling a System Password....................................................................................................... 43

4 Diagnostics..........................................................................................................44

Enhanced Pre-Boot System Assessment (ePSA) Diagnostics........................................................... 44

5 Troubleshooting Your Computer....................................................................45

Power LED Diagnostics.......................................................................................................................45

Beep Code...........................................................................................................................................46

Error Messages....................................................................................................................................46

6 Specifications......................................................................................................50

7 Contacting Dell................................................................................................... 56

Working on Your Computer

Before Working Inside Your Computer

Use the following safety guidelines to help protect your computer from potential damage and to help to

ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes

that the following conditions exist:

• You have read the safety information that shipped with your computer.

• A component can be replaced or--if purchased separately--installed by performing the removal

procedure in reverse order.

WARNING: Disconnect all power sources before opening the computer cover or panels. After you

finish working inside the computer, replace all covers, panels, and screws before connecting to

the power source.

WARNING: Before working inside your computer, read the safety information that shipped with

your computer. For additional safety best practices information, see the Regulatory Compliance

Homepage at www.dell.com/regulatory_compliance

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or

by periodically touching an unpainted metal surface, such as a connector on the back of the

computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts

on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a

processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable

itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable,

press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep

them evenly aligned to avoid bending any connector pins. Also, before you connect a cable,

ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear differently than shown in

this document.

To avoid damaging your computer, perform the following steps before you begin working inside the

computer.

1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

2. Turn off your computer (see Turning Off Your Computer).

CAUTION: To disconnect a network cable, first unplug the cable from your computer and

then unplug the cable from the network device.

3. Disconnect all network cables from the computer.

4. Disconnect your computer and all attached devices from their electrical outlets.

5. Press and hold the power button while the computer is unplugged to ground the system board.

6. Remove the cover.

CAUTION: Before touching anything inside your computer, ground yourself by touching an

unpainted metal surface, such as the metal at the back of the computer. While you work,

periodically touch an unpainted metal surface to dissipate static electricity, which could

harm internal components.

Turning Off Your Computer

CAUTION: To avoid losing data, save and close all open files and exit all open programs before

you turn off your computer.

1. Shut down the operating system:

• In Windows 8:

– Using a touch-enabled device:

a. Swipe in from the right edge of the screen, opening the Charms menu and select

Settings.

b. Select the and then select Shut down

– Using a mouse:

a. Point to upper-right corner of the screen and click Settings.

b. Click the and select Shut down.

• In Windows 7:

1. Click Start .

2. Click Shut Down.

1. Click Start .

2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click

Shut Down..

2. Ensure that the computer and all attached devices are turned off. If your computer and attached

devices did not automatically turn off when you shut down your operating system, press and hold

the power button for about 6 seconds to turn them off.

After Working Inside Your Computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and

cables before turning on your computer.

1. Replace the cover.

CAUTION: To connect a network cable, first plug the cable into the network device and then

plug it into the computer.

2. Connect any telephone or network cables to your computer.

3. Connect your computer and all attached devices to their electrical outlets.

4. Turn on your computer.

5. If required, verify that the computer works correctly by running the Dell Diagnostics.

Removing and Installing Components

This section provides detailed information on how to remove or install the components from your

computer.

Recommended Tools

The procedures in this document may require the following tools:

• Small flat-blade screwdriver

• Phillips screwdriver

• Small plastic scribe

Front and Back View

Figure 1. Front and Back View Of Mini-Tower

1. power button or power light 2. flex bay

3. microphone connector 4. headphone connector

5. hard-drive activity light 6. power-supply diagnostic light

7. power-supply diagnostic button 8. power cable connector

9. keyboard connector 10. USB 2.0 connector

11. display port connector 12. USB 3.0 connector

13. VGA connector 14. line-in or microphone connector

15. expansion-card slots 16. security-cable slot

17. padlock ring 18. mouse connector

19. network connector 20. serial connector

21. line-out connector

Removing the Cover

1. Follow the procedures in Before Working Inside Your Computer.

2. Pull up the cover release latch, and lift the cover upwards to remove it from the computer.

Installing the Cover

1. Align the cover along its tabs on the chassis of the computer.

2. Press down on the cover till it clicks into place.

3. Follow the procedures in After Working Inside Your Computer.

Removing the Intrusion Switch

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the cover.

3. Disconnect the intrusion-switch cable from the system board.

4. Slide the intrusion switch toward the bottom of the chassis and remove it from the computer.

Installing the Intrusion Switch

1. Insert the intrusion switch into its place in the chassis rear and slide it towards the top to secure it.

2. Connect the intrusion cable to the system board.

3. Install the cover.

4. Follow the procedures in After Working Inside Your Computer.

Removing the Wireless Local Area Network (WLAN) Card

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the cover.

3. Remove the screws that secure the antenna to the computer.

4. Disconnect the antenna from the computer.

5. Press the blue tab and lift the latch outwards and remove the WLAN card from the connector on the

system board.

Installing the Wireless Local Area Network (WLAN) Card

1. Insert the WLAN card into the connector on the system board and press down until it is secured.

2. Affix the latch.

3. Place the antenna puck on the connector and tighten the screws to secure it to the computer.

4. Install the cover.

5. Follow the procedures in After Working Inside Your Computer.

Removing the Front Bezel

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the cover.

3. Gently pry the front panel retention clips away from the chassis located at the edge of front panel.

4. Rotate the front panel away from the computer to release the hooks on the opposite edge of the

panel from the chassis.

Installing the Front Bezel

1. Insert the hooks along the bottom edge of the front bezel into the slots on the chassis front.

2. Rotate the bezel toward the computer to engage the front-bezel retention clips until they click into

place.

3. Install the cover.

4. Follow the procedures in After Working Inside Your Computer.

Removing the Expansion Card

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the cover.

3. Press the tab to release the latch.

4. Pull the release lever away from the PCI x16 card until you release the securing tab from the dent in

the card. Lift the card out of its connector and remove it from the system board.

Installing the Expansion Card

1. Insert the expansion card in the connector on the system board and press down until secured.

2. Push the retention latch back to its position.

3. Install the cover.

4. Follow the procedures in After Working Inside Your Computer.

Memory Module Guidelines

To ensure optimal performance of your computer, observe the following general guidelines when

configuring your system memory:

• Memory modules of different sizes can be mixed (for example, 2 GB and 4 GB). But, all populated

channels must have identical configurations.

• Memory modules must be installed beginning with the first socket.

NOTE: The memory sockets in your computer may be labeled differently depending on the

hardware configuration. For example, A1, A2 or 1,2,3.

• If the quad-rank memory modules are mixed with single or dual-rank modules, the quad-rank

modules must be installed in the sockets with the white release levers.

• If memory modules with different speeds are installed, they operate at the speed of the slowest

installed memory modules.

Removing the Memory

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the cover.

3. Press down on the memory retaining tabs on each side of the memory modules, and lift the memory

modules out of the connectors on the system board.

Installing the Memory

1. Align the notch on the memory-card with the tab in the system-board connector.

2. Press down on the memory module until the release tabs spring back to secure them in place.

3. Install the cover.

4. Follow the procedures in After Working Inside Your Computer.

Removing the Coin-Cell Battery

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. cover

b. expansion card(s)

3. Locate the coin-cell battery on the system board.

4. Press the release latch away from the battery to allow the battery to pop-up from the socket and lift

the coin-cell battery out of the computer.

Installing the Coin-Cell Battery

1. Place the coin cell battery in its slot on the system board and press until the release latch springs

back into place and secures it.

2. Install:

a. expansion card

b. cover

3. Follow the procedures in After Working Inside Your Computer.

Removing the Hard Drive

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the cover.

3. Disconnect the data cable and the power cable from the back of the hard drive. Press the blue

securing-bracket tabs inwards and lift the hard-drive bracket out of the hard-drive bay.

4. Flex the hard-drive bracket and remove the hard drive from the hard-drive bracket.

Installing the Hard Drive

1. Insert the hard drive into the hard-drive bracket.

2. Press the securing brackets inward and slide the hard-drive bracket into the bay.

3. Connect the data cable and the power cable to the back of the hard-drive.

4. Install the cover.

5. Follow the procedures in After Working Inside Your Computer.

Removing the Optical Drive

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. cover

b. front bezel

3. Disconnect the data cable and the power cable from the back of the optical drive.

4. Slide and hold the optical-drive latch to unlock the optical drive and pull the optical drive out of the

computer.

5. Repeat steps 3 and 4 to remove the second optical drive (if available).

Installing the Optical Drive

1. Push the optical drive from the front toward the back of the computer till it is secured by the optical-

drive latch.

2. Connect the data cable and power cable to the back of the optical drive.

3. Install:

a. front bezel

b. cover

4. Follow the procedures in After Working Inside Your Computer.

Removing the Speaker

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the cover.

3. Disconnect and release the speaker cable from system board. Press down the speaker-securing tab

and slide the speaker upwards to remove.

Installing the Speaker

1. Slide the speaker downwards into its slot to secure it.

2. Thread the speaker cable into the chassis clip and connect the speaker cable to the system board.

3. Install the cover.

4. Follow the procedures in After Working Inside Your Computer.

Removing the Power Supply

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the cover.

3. Disconnect the 4-pin and 8-in power cables from the system board and release the cable from the

tab.

4. Remove the screws that secure the power supply to the back of the computer.

5. Push in on the blue release tab beside the power supply, and slide the power supply towards the

front of the computer. Lift and remove the power supply out of the computer.

Installing the Power Supply

1. Place the power supply in the chassis and slide towards the back of the system to secure it.

2. Tighten the screws to secure the power supply to the back of the computer.

3. Connect the 4-pin and 8-pin power cables to the system board.

4. Thread the power cables through the chassis clips.

5. Install the cover.

6. Follow the procedures in After Working Inside Your Computer.

Removing the Heat Sink Assembly

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the cover.

3. Disconnect the fan cable from the system board. Loosen the captive screws in diagonal order and lift

the heat-sink assembly away from the computer.

Installing the Heat Sink Assembly

1. Place the heat sink assembly into the chassis.

2. Tighten the captive screws in diagonal order to secure the heat sink assembly to the computer.

3. Connect the fan cable to the system board.

4. Install the cover.

5. Follow the procedures in After Working Inside Your Computer.

Removing the Processor

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. cover

b. heat-sink assembly

3. Press the release lever down and then move it outward to release it from the retention hook. Lift the

processor cover and remove the processor from the socket. Place it in an antistatic bag.

Installing the Processor

1. Insert the processor in the processor socket. Ensure the processor is properly seated.

2. Lower the processor cover.

3. Press the release lever down and then move it inward to secure it with the retention hook.

4. Install:

a. heat-sink assembly

b. cover

5. Follow the procedures in After Working Inside Your Computer.

Removing the System Fan

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the cover.

3. Press the clip to release and disconnect the system-fan cable from the system board.

4. Pry and remove the system fan away from the four grommets securing it to the back of the

computer.

Installing the System Fan

1. Place the system fan in the chassis.

2. Pass the four grommets through the chassis and slide outward along the groove to secure in place.

3. Connect the system-fan cable to the system board.

4. Install the cover.

5. Follow the procedures in After Working Inside Your Computer.

Removing the Thermal Sensor

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the cover.

3. Disconnect the thermal-sensor cable from the system board.

4. Release the thermal-sensor cable from the chassis clip.

5. Press the tabs on both sides to release and remove the thermal sensor away from the chassis.

Installing the Thermal Sensor

1. Secure the thermal sensor to the chassis.

2. Thread the thermal-sensor cable into the chassis clips.

3. Connect the thermal-sensor cable to the system board.

4. Install the cover.

5. Follow the procedures in After Working Inside Your Computer.

Removing the Power Switch

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the:

a. cover

b. front bezel

c. optical drive

3. Disconnect the power-switch cable from the system board.

4. Release the power-switch cable from the chassis clips.

5. Press the clips on both side of the power switch to release it from the chassis and, slide to remove

the power switch along its cable from the computer.

Installing the Power Switch

1. Slide the power switch in through the front of the computer.

2. Secure the power-switch cable to the chassis.

3. Thread the power-switch cable into the chassis clips.

4. Connect the power-switch cable to the system board.

5. Install the:

a. optical drive

b. front bezel

c. cover

6. Follow the procedures in After Working Inside Your Computer.

Removing the Input/Output (I/O) Panel

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove:

a. cover

b. front bezel

3. Disconnect the I/O panel, data, and USB data cables from the system board.

4. Unthread and release the I/O Panel, data cable and USB data cable from the clip on the computer.

5. Remove the screw that secures the I/O panel to the computer.

6. Slide the I/O panel towards the left of the computer to release it and pull the I/O panel along with its

cable out of the computer.

Installing the Input/Output (I/O) Panel

1. Insert the I/O panel into the slot on the chassis front.

2. Slide the I/O panel towards the right of the computer to secure to the chassis.

3. Tighten the screw to secure the I/O panel to the chassis.

4. Thread the I/O panel, data cable and USB data cable into the chassis clip.

5. Connect the I/O panel, data cable and USB data cable to the system board.

6. Install :

a. front bezel

b. cover

7. Follow the procedures in After Working Inside Your Computer.

Removing the System Board

1. Follow the procedures in Before Working Inside Your Computer.

2. Remove the:

a. cover

b. memory

c. expansion card(s)

d. heat-sink assembly

e. processor

3. Disconnect all the cables from the system board.

4. Remove the screws that secure the system board to the computer and slide the system board

towards the front of the computer.

5. Tilt the system board at 45–degrees, and then lift the system board out of the computer.

Installing the System Board

1. Align the system board to the port connectors on the rear of the chassis and place the system board

in the chassis.

2. Tighten the screws securing the system board to the chassis.

3. Connect the cables to the system board.

4. Install the:

a. processor

b. heat-sink assembly

c. expansion card(s)

d. memory

e. cover

5. Follow the procedures in After Working Inside Your Computer.

System Board Layout

The following image displays the system board layout of the computer.

1. PCI Express x16 slot (wired as X4)

2. PCI slot

3. PCIe x1 slot

4. coin-cell battery

5. PCI Express x16 slot

6. intrusion switch connector

7. 4–pin CPU power connector

8. system-fan connector

9. processor socket

10. heatsink-fan connector

11. memory connectors ( SODIMM sockets)

12. front power-switch connector

13. 8–pin power connector

14. SATA connectors

15. HDD and optical drive power connector

16. SATA connectors

17. front panel USB connector

18. front panel audio connector

19. password reset jumper

20. internal USB 2.0 connector

21. RTCRST jumper connector

22. speaker connector

System Setup

System Setup enables you to manage your computer hardware and specify BIOS‐level options. From the

System Setup, you can:

• Change the NVRAM settings after you add or remove hardware

• View the system hardware configuration

• Enable or disable integrated devices

• Set performance and power management thresholds

• Manage your computer security

Boot Sequence

Boot Sequence allows you to bypass the System Setup‐defined boot device order and boot directly to a

specific device (for example: optical drive or hard drive). During the Power-on Self Test (POST), when the

Dell logo appears, you can:

• Access System Setup by pressing <F2> key

• Bring up the one-time boot menu by pressing <F12> key

The one-time boot menu displays the devices that you can boot from including the diagnostic option.

The boot-menu options are:

• Removable Drive (if available)

• STXXXX Drive

NOTE: XXX denotes the SATA drive number.

• Optical Drive

• Diagnostics

NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.

The boot sequence screen also displays the option to access the System Setup screen.

Navigation Keys

The following table displays the system setup navigation keys.

NOTE: For most of the system setup options, changes that you make are recorded but do not take

effect until you re-start the system.

Table 1. Navigation Keys

Keys Navigation

Up arrow Moves to the previous field.

Down arrow Moves to the next field.

<Enter> Allows you to select a value in the selected field (if applicable) or follow the link in

the field.

Spacebar Expands or collapses a drop‐down list, if applicable.

<Tab> Moves to the next focus area.

NOTE: For the standard graphics browser only.

<Esc> Moves to the previous page till you view the main screen. Pressing <Esc> in the main

screen displays a message that prompts you to save any unsaved changes and

restarts the system.

<F1> Displays the System Setup help file.

System Setup Options

NOTE: Depending on the computer and its installed devices, the items listed in this section may or

may not appear

Table 2. General

Option Description

System Information Displays the following information:

•System Information - Displays BIOS Version, Service Tag, Asset Tag,

Ownership Tag, Ownership Date, Manufacture Date, and the Express

Service Code.

•Memory Information - Displays Memory Installed, Memory Available,

Memory Speed, Memory Channels Mode, Memory Technology, DIMM

1 Size, DIMM 2 Size, DIMM 3 Size and DIMM 4 Size.

•PCI Information - Displays SLOT1, and SLOT2

•Processor Information - Displays Processor Type, Core Count,

Processor ID, Current Clock Speed, Minimum Clock Speed, Maximum

Clock Speed, Processor L2 Cache, Processor L3 Cache, HT Capable,

and 64-Bit Technology.

•Device Information - Displays SATA-0, SATA-1, SATA-2 , LOM MAC

Address, Audio Controller and Video Controller.

Boot Sequence Allows you to specify the order in which the computer attempts to find an

operating system. The options are:

• Diskette drive

• WDC WD2500AAKX-75U6AA0

• USB Storage Device

• CD/DVD/CD-RW Drive

• Onboard NIC

Advanced Boot Options • Legacy

Option Description

• UEFI

Advance Boot Options Enable Legacy Option ROMs - This option is enabled by default.

Date/Time Allows you to set the date and time. The changes to the system date and

time takes effect immediately.

Table 3. System Configuration

Option Description

Integrated NIC Allows you to enable or disable the integrated network card. You can set

the integrated NIC to:

• Enable UEFI Network Stack (disable by default)

• Disabled

• Enabled

•Enabled w/PXE- This option is enabled by default.

• Enabled w/Cloud Desktop

NOTE: Depending on the computer and the devices installed, the

items listed in this section may or may not appear.

Serial Port Allows you to define the serial port settings. You can set the serial port to:

• Disabled

• COM1

• COM2

• COM3

• COM4

NOTE: The operating system may allocate resources even though the

setting is disabled.

SATA Operation Allows you to configure the operating mode of the integrated hard drive

controller.

•Disabled - The SATA controllers are hidden.

•ATA - SATA is configured for ATA mode.

•AHCI - SATA is configured for AHCI mode.

Drives Allows you to enable or disable the various on-board drives:

• SATA-0

• SATA-1

• SATA-2

SMART Reporting This field controls if the hard drive errors for the integrated drives are

reported during system startup. This technology is part of the SMART (Self

Monitoring Analysis and Reporting Technology) specification.

•Enable SMART Reporting - This option is disabled by default.

USB Configuration This field configures the integrated USB controller. If Boot Support is

enabled, the system is allowed to boot any type of USB mass storage

devices (HDD, memory key, floppy).

Option Description

If USB port is enabled, device attached to this port is enabled and available

for operation system.

If USB port is disabled, the operation system cannot see any device

attached to this port.

USB configuration:

For Mini-Tower, Small Form Factor the options are:

• Enable Boot Support

• Enable Front USB 2.0 Ports

• Enable USB 3.0 Ports

• Enable Rear—Left Dual USB 2.0 Ports

• Enable Rear —Right Dual USB 2.0 Ports (default value is enable)

NOTE: USB keyboard and mouse always work in the BIOS setup

irrespective of these settings.

Audio Allows you to enable or disable the integrated audio controller.

•Enable Audio - This option is selected by default.

Table 4. Security

Option Description

Internal HDD_O Password This field lets you set, change, or delete the administrator (admin)

password (sometimes called the setup password). The admin password

enables several security features.

The drive does not have a password set by default.

• Enter the old password

• Enter the new password

• Confirm the new password

Strong Password Enable strong password - This option is disabled by default.

Password Configuration This field controls the minimum and maximum number of characters

allowed for the admin and system passwords.

• Admin Password Min

• Admin Password Max

• System Password Min

• System Password Max

Password Bypass Allows you to bypass the System Password and the internal HDD password

prompts during a system restart. This option is disabled by default.

• Disabled - Always prompt for the system and internal HDD password

when they are set.

• Reboot Bypass - Bypass the password prompts on restarts (warm

boots).

Option Description

NOTE: The system will always prompt for the system and internal

HDD passwords when powered on from the off state (a cold boot).

Also, the system will always prompt for passwords on any module bay

HDDs that may be present.

Password Change Allows you to determine whether changes to the system and hard disk

passwords are permitted when an administrator password is set.

•Allow Non-Admin Password Changes - This option is enabled by

default.

TPM Security This option lets you control whether the Trusted Platform Module (TPM) in

the system is enabled and visible to the operating system.

TPM Security - This option is disabled by default.

NOTE: Activation, deactivation, and clear options are not affected if

you load the setup program's default values. Changes to this option

take effect immediately.

Computrace This field lets you activate or disable the BIOS module interface of the

optional Computrace Service from Absolute Software.

•Deactivate - This option is selected by default.

• Disable

• Activate

Chassis Intrusion •Enable - This option is selected by default.

• Disable

• On-Silent

CPU XD Support Allows you to enable or disable the execute disable mode of the processor.

•Enable CPU XD Support - This option is enabled by default.

OROM Keyboard Access Allows you to determine if you access the Option Read Only Memory

(OROM) configuration screens via hotkeys during boot. These settings

prevent access to the Intel RAID (CTRL+I) or Intel Management Engine

BIOS Extension (CTRL+P/F12).

•Enable - User may enter OROM configuration screens via the hotkey.

This option is selected by default.

•One-Time Enable - User can enter the OROM configuration screens

via the hotkeys during the next boot. After the boot, the setting will

revert to disabled.

•Disable - User can not enter the OROM configuration screens via the

hotkey.

This option is set to Enable by default.

Admin Setup Lockout Allows you to enable or disable the option to enter setup when an admin

password is set.

•Enable Admin Setup Lockout - This option is not set by default.

HDD Protection Support Allows you to enable or disable the HDD Protection feature

•HDD Protection Support - This option is not set by default.

Table 5. Secure Boot

Secure Boot Enable Allows you to enable or disable Secure Boot feature

•Disabled - This option is selected by default.

• Enabled

NOTE: To enable secure boot, UEFI boot mode must be enabled and

Enable Legacy Option ROMs must be disabled or turned off.

Expert key Management Allows you to manipulate the security key databases only if the system is in

Custom Mode. The Enable Custom Mode option is disabled by default.

The options are:

• PK

• KEK

• db

• dbx

If you enable the Custom Mode, the relevant options for PK, KEK, db, and

dbx appear. The options are:

•Save to File- Saves the key to a user-selected file

•Replace from File- Replaces the current key with a key from a user-

selected file

•Append from File- Adds a key to the current database from a user-

selected file

•Delete- Deletes the selected key

•Reset All Keys- Resets to default setting

•Delete All Keys- Deletes all the keys

NOTE: If you disable the Custom Mode, all the changes made will be

erased and the keys will restore to default settings.

Table 6. Performance

Option Description

Multi Core Support Specifies whether the process will have one or all cores enabled. The

performance of some applications will improve with the additional cores.

• All - This option is enabled by default

• 1

• 2

NOTE: To enable Trusted Execution mode, all cores must be enabled.

Intel SpeedStep Allows you to enable or disable the Intel SpeedStep mode of the

processor.

•Enable Intel SpeedStep - This option is enabled by default.

C States Control Allows you to enable or disable the additional processor sleep states.

•C States - This option is enabled by default.

Limit CPUID Value This field limits the maximum value the processor Standard CPUID

Function will support.

•Enable CPUID Limit - This option is not set by default.

Option Description

NOTE: Some Operating system will not complete installation when

the maximum CPUID Function is greater than 3.

Intel TurboBoost Allows you to enable or disable Intel TurboBoost mode of the processor.

• Disabled - Does not allow the TurboBoost driver to increase the

performance state of the processor above the standard performance.

• Enabled - Allows the Intel TurboBoost driver to increase the

performance of the CPU or graphics processor.

Rapid Start Technology Allows you to improve batter life by automatically putting the system into a

low power status during after user specified amount of time.

• Intel Rapid Start feature

NOTE: Rapid Start Technology will automatically be disabled due to

configuration changes:

• Hard Disk Configuration or partition have been changed

• System or HDD password is enabled

• A Dell Encryption Accelerator is installed

• The Block Sleep setting is enabled

Table 7. Power Management

Option Description

AC Recovery Specifies how the computer will respond when AC power is applied after

an AC power loss. You can set the AC Recovery to:

• Power Off - This option is enabled by default.

• Power On

• Last Power State

Auto On Time This option sets the time of the day when you would like the system to

turn on automatically. Time is kept in standard 12-hour format

(hour:minutes:seconds). The startup time can be changed by typing the

values in the time and A.M./P.M. fields.

•Disabled - The system will not automatically power up. This option is

selected by default.

•Every Day - The system will power up every day at the time you

specified above .

•Weekdays - The system will power up Monday through Friday at the

time you specified above.

•Select Days - The system will power up on days selected above at the

time you specified above.

NOTE: This feature does not work if you turn off your computer using

the switch on a power strip or surge protector or if Auto Power is set

to disabled.

Deep Sleep Control Allows you to define the controls when Deep Sleep is enabled.

• Disabled

• Enabled in S5 only

• Enabled in S4 and S5

Option Description

This option is disabled by default.

Fan Control Override Controls the speed of the system fan. This option is disabled by default.

NOTE: When enabled, the fan runs at full speed.

USB Wake Support This option allows you to enable USB devices to wake the computer from

standby.

•Enable USB Wake Support - This option is selected by default.

Wake on LAN This option allows the computer to power up from the off state when

triggered by a special LAN signal. Wake-up from the Standby state is

unaffected by this setting and must be enabled in the operating system.

This feature only works when the computer is connected to AC power

supply. The options differ based on the form factor.

•Disabled - Does not allow the system to power on by special LAN

signals when it receives a wake-up signal from the LAN or wireless LAN.

•LAN Only - Allows the system to be powered on by special LAN signals.

•LAN with PXE Boot - Allows the system to be powered on by special

LAN signals. After waking the system, do a PXE boot.

This option is Disabled by default.

Block Sleep This option lets you block entering to sleep (S3 state) in operating system

environment.

•Block Sleep (S3 state) - This option is disabled by default.

Intel Smart Connect

Technology

The option is disabled by default. If option enables will periodically sense

nearby wireless connection while the system is asleep. It will synchronize

emails or social media application that were open when system entered

the sleep state.

• Smart Connect

Table 8. POST Behavior

Option Description

Numlock LED Specifies if the NumLock function can be enabled when the system boots.

This option is enabled by default.

Keyboard Errors Specifies whether keyboard related errors are reported when it boots. This

option is enabled by default.

MEBx Hotkeys Specifies whether the MEBx Hotkey function should be enable when the

system boots.

•Enable MEBx Hotkey — This option is enabled by default

Table 9. Virtualization Support

Option Description

Virtualization This option specifies whether a Virtual Machine Monitor (VMM) can utilize

the additional hardware capabilities provided by Intel Virtualization

technology.

Option Description

•Enable Intel Virtualization Technology - This option is enabled by

default.

VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the

additional hardware capabilities provided by Intel® Virtualization

technology for direct I/O.

•Enable Intel Virtualization Technology for Direct I/O - This option is

enabled by default.

Trusted Execution This option specifies whether a Measured Virtual Machine Monitor (MVMM)

can utilize the additional hardware capabilities provided by Intel Trusted

Execution technology. The TPM virtualization technology, and

Virtualization technology for direct I/O must be enabled to use this feature.

•Trusted Execution - This option is disabled by default.

Table 10. Maintenance

Option Description

Service Tag Displays the service tag of your computer.

Asset Tag Allows you to create a system asset tag if an asset tag is not already set.

This option is not set by default.

SERR Messages Controls the SERR message mechanism. This option is not set by default.

Some graphics cards require that the SERR message mechanism be

disabled.

Table 11. Cloud Desktop

Option Description

Server Lookup Method Specifies how the Cloud Desktop software will looks up the server

addresses.

• Static IP

• DNS - This option is enabled by default.

NOTE: This field is only relevant when the Integrated NIC control in

the System Configuration group is set to Enable with Cloud Desktop.

Server Name Specifies server name of the server.

NOTE: This field is only relevant when the Integrated NIC control in

the System Configuration group is set to Enable with Cloud Desktop.

Server IP Address Specifies the primary static IP address of the Cloud Desktop server with

which the client software communicates. The default IP address is

255.255.255.255.

NOTE: This field is only relevant when the Integrated NIC control in

the System Configuration group is set to Enable with Cloud Desktop .

Server Port Specifies the primary IP port of the Cloud Desktop, which is used by the

client to communicate. The default IP port is 06910.

Option Description

NOTE: This field is only relevant when the Integrated NIC control in

the System Configuration group is set to Enable with Cloud Desktop.

Client Address Method Specifies how the client obtains the IP address.

• Static IP

• DHCP - This option is enabled by default.

NOTE: This field is only relevant when the Integrated NIC control in

the System Configuration group is set to Enable with Cloud Desktop.

Client IP Address Specifies the static IP address of the client. The default IP address is

255.255.255.255.

NOTE: This field is only relevant when the Integrated NIC control in

the System Configuration group is set to Enable with Cloud Desktop.

Client SubnetMask Specifies the subnet mask of the client. The default setting is

255.255.255.255.

NOTE: This field is only relevant when the Integrated NIC control in

the System Configuration group is set to Enable with Cloud Desktop .

Client Gateway Specifies the gateway IP address of the client. The default setting is

255.255.255.255.

NOTE: This field is only relevant when the Integrated NIC control in

the System Configuration group is set to Enable with Cloud Desktop .

DNS IP Address Specifies the DNS IP Address of the client. The default setting is

255.255.255.255.

NOTE: This field is only relevant when the Integrated NIC control in

the System Configuration group is set to Enable with Cloud Desktop.

Domain Name Specifies the Domain Name of the client.

NOTE: This field is only relevant when the Integrated NIC control in

the System Configuration group is set to Enable with Cloud Desktop,

and when the Client Address Method is set to Static IP.

Advanced Specifies for Advanced debugging

• Verbose Mode - This option is not set by default.

NOTE: This Option is only relevant when the integrated NIC control in

the System Configuration group is set to enable with Cloud Desktop.

Table 12. System Logs

Option Description

BIOS events Displays the system event log and allows you to clear the log.

• Clear Log

Updating the BIOS

It is recommended to update your BIOS (system setup), on replacing the system board or if an update is

available. For laptops, ensure that your computer battery is fully charged and connected to a power

outlet

1. Re-start the computer.

2. Go to dell.com/support.

3. Enter the Service Tag or Express Service Code and click Submit.

NOTE: To locate the Service Tag, click Where is my Service Tag?

NOTE: If you cannot find your Service Tag, click Detect My Product. Proceed with the

instructions on screen.

4. If you are unable to locate or find the Service Tag, click the Product Category of your computer.

5. Choose the Product Type from the list.

6. Select your computer model and the Product Support page of your computer appears.

7. Click Get drivers and click View All Drivers.

The Drivers and Downloads page opens.

8. On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS.

9. Identify the latest BIOS file and click Download File.

You can also analyze which drivers need an update. To do this for your product, click Analyze

System for Updates and follow the instructions on the screen.

10. Select your preferred download method in the Please select your download method below

window; click Download File.

The File Download window appears.

11. Click Save to save the file on your computer.

12. Click Run to install the updated BIOS settings on your computer.

Follow the instructions on the screen.

Jumper Settings

To change a jumper setting, pull the plug off its pin(s) and carefully fit it down onto the pin(s) indicated on

the system board. The following table displays the system board jumper settings.

Table 13. Jumper Settings

Jumper Setting Description

PSWD Default Password features are enabled

RTCRST pin 1 and 2 Real-time clock reset. Can be used for

troubleshooting.

System and Setup Password

You can create a system password and a setup password to secure your computer.

Password Type Description

System password Password that you must enter to log on to your system.

Setup password Password that you must enter to access and make changes to the BIOS settings of

your computer.

CAUTION: The password features provide a basic level of security for the data on your computer.

CAUTION: Anyone can access the data stored on your computer if it is not locked and left

unattended.

NOTE: Your computer is shipped with the system and setup password feature disabled.

Assigning a System Password and Setup Password

You can assign a new System Password and/or Setup Password or change an existing System Password

and/or Setup Password only when Password Status is Unlocked. If the Password Status is Locked, you

cannot change the System Password.

NOTE: If the password jumper is disabled, the existing System Password and Setup Password is

deleted and you need not provide the system password to log on to the computer.

To enter a system setup, press <F2> immediately after a power-on or re-boot.

1. In the System BIOS or System Setup screen, select System Security and press <Enter>.

The System Security screen appears.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password , enter your system password, and press <Enter> or <Tab>.

Use the following guidelines to assign the system password:

• A password can have up to 32 characters.

• The password can contain the numbers 0 through 9.

• Only lower case letters are valid, upper case letters are not allowed.

• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

Re-enter the system password when prompted.

4. Type the system password that you entered earlier and click OK.

5. Select Setup Password, type your system password and press <Enter> or <Tab>.

A message prompts you to re-type the setup password.

6. Type the setup password that you entered earlier and click OK.

7. Press <Esc> and a message prompts you to save the changes.

8. Press <Y> to save the changes.

The computer reboots.

Deleting or Changing an Existing System and/or Setup Password

Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change

the existing System and/or Setup password. You cannot delete or change an existing System or Setup

password, if the Password Status is Locked.

To enter the System Setup, press <F2> immediately after a power-on or reboot.

1. In the System BIOS or System Setup screen, select System Security and press <Enter>.

The System Security screen is displayed.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password, alter or delete the existing system password and press <Enter> or <Tab>.

4. Select Setup Password, alter or delete the existing setup password and press <Enter> or <Tab>.

NOTE: If you change the System and/or Setup password, re-enter the new password when

promoted. If you delete the System and/or Setup password, confirm the deletion when

promoted.

5. Press <Esc> and a message prompts you to save the changes.

6. Press <Y> to save the changes and exit from the System Setup.

The computer reboots.

Disabling a System Password

The system's software security features include a system password and a setup password. The password

jumper disables any password(s) currently in use.

NOTE: You can also use the following steps to disable a forgotten password.

1. Follow the procedures in Before Working on Your Computer.

2. Remove the cover.

3. Identify the PSWD jumper on the system board.

4. Remove the PSWD jumper from the system board.

NOTE: The existing passwords are not disabled (erased) until the computer boots without the

jumper.

5. Install the cover.

NOTE: If you assign a new system and/or setup password with the PSWD jumper installed, the

system disables the new password(s) the next time it boots.

6. Connect the computer to the electrical outlet and power-on the computer.

7. Power-off the computer and disconnect the power cable from the electrical outlet.

8. Remove the cover.

9. Replace the PSWD jumper on the system board.

10. Install the cover.

11. Follow the procedures in After Working on Your Computer.

12. Power-on the computer.

13. Go to the system setup, and assign a new system or setup password. See Setting up a System

Password.

Diagnostics

If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for

technical assistance. The purpose of running diagnostics is to test your computer's hardware without

requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service

and support personnel can use the diagnostics results to help you solve the problem.

Enhanced Pre-Boot System Assessment (ePSA)

Diagnostics

The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware.

The ePSA is embedded with the BIOS and is launched by the BIOS internally. The embedded system

diagnostics provides a set of options for particular devices or device groups allowing you to:

• Run tests automatically or in an interactive mode

• Repeat tests

• Display or save test results

• Run thorough tests to introduce additional test options to provide extra information about the failed

device(s)

• View status messages that inform you if tests are completed successfully

• View error messages that inform you of problems encountered during testing

CAUTION: Use the system diagnostics to test only your computer. Using this program with other

computers may cause invalid results or error messages.

NOTE: Some tests for specific devices require user interaction. Always ensure that you are present

at the computer terminal when the diagnostic tests are performed.

1. Power-on the computer.

2. As the computer boots, press the <F12> key as the Dell logo appears.

3. On the boot menu screen, select the Diagnostics option.

The Enhanced Pre-boot System Assessment window is displayed, listing all devices detected in the

computer. The diagnostics starts running the tests on all the detected devices.

4. If you wish to run a diagnostic test on a specific device, press <Esc> and click Yes to stop the

diagnostic test.

5. Select the device from the left pane and click Run Tests.

6. If there are any issues, error codes are displayed.

Note the error code and contact Dell.

Troubleshooting Your Computer

You can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error

Messages during the operation of the computer.

Power LED Diagnostics

The power button LED located on the front of the chassis also functions as a bicolored diagnostic LED.

The diagnostic LED is only active and visible during the POST process. Once the operating system starts

to load, it is no longer visible.

Amber LED blinking scheme – The pattern is 2 or 3 blinks followed by a short pause then x number of

blinks up to 7. The repeated pattern has a long pause inserted in the middle. For example 2,3 = 2 amber

blinks, short pause, 3 amber blinks followed by long pause then repeats.

Table 14. Power LED Diagnostics

Amber LED State White LED State Description

off off system is OFF

off blinking system is in sleep state

blinking off power supply unit (PSU) failure

steady off PSU is working but failed to fetch code

off steady system is ON

Amber LED State Description

2,1 system board failure

2,2 system board, PSU or PSU cabling failure

2,3 system board, memory or CPU failure

2, 4 coin-cell battery failure

2,5 corrupt BIOS

2,6 CPU configuration failure or CPU failure

2,7 memory modules are detected, but a memory failure

3,1 possible peripheral card or system board failure

3,2 possible USB failure

3,3 no memory modules are detected

Amber LED State Description

3,4 possible system board error

3,5 memory modules are detected, but a memory configuration or compatibility error

3,6 possible system board resource and/or hardware failure

3,7 some other failure with messages on screen

Beep Code

The computer can emit a series of beeps during start-up if the display does not show errors or problems.

These series of beeps, called beep codes, identify various problems. The delay between each beep is 300

ms, the delay between each set of beeps is 3 sec, and the beep sound lasts 300 ms. After each beep and

each set of beeps, the BIOS should detect if the user presses the power button. If so, BIOS will jump out

from looping and execute the normal shutdown process and power system.

Code 1-3-2

Cause Memory failure

Error Messages

Error Message Description

Address mark not

found

The BIOS found a faulty disk sector or could not find a particular disk sector.

Alert! Previous

attempts at

booting this

system have failed

at checkpoint

[nnnn]. For help in

resolving this

problem, please

note this

checkpoint and

contact Dell

Technical Support.

The computer failed to complete the boot routine three consecutive times for the

same error. Contact Dell and report the checkpoint code (nnnn) to the support

technician

Alert! Security

override Jumper is

installed.

The MFG_MODE jumper has been set and AMT Management features are disabled

until it is removed.

Attachment failed

to respond

The floppy or hard drive controller cannot send data to the associated drive.

Error Message Description

Bad command or

file name

Ensure that you have spelled the command correctly, put spaces in the proper

place, and used the correct pathname.

Bad error-

correction code

(ECC) on disk read

The floppy or hard drive controller detected an uncorrectable read error.

Controller has

failed

The hard drive or the associated controller is defective.

Data error The floppy or hard drive cannot read the data. For the Windows operating system,

run the chkdsk utility to check the file structure of the floppy or hard drive. For any

other operating system, run the appropriate corresponding utility.

Decreasing

available memory

One or more memory modules may be faulty or improperly seated. Re-install the

memory modules and, if necessary, replace them.

Diskette drive 0

seek failure

A cable may be loose or the computer configuration information may not match

the hardware configuration.

Diskette read

failure

The floppy disk may be defective or a cable may be loose. If the drive access light

turns on, try a different disk.

Diskette subsystem

reset failed

The floppy drive controller may be faulty.

Gate A20 failure One or more memory modules may be faulty or improperly seated. Reinstall the

memory modules and, if necessary, replace them.

General failure The operating system is unable to carry out the command. This message is usually

followed by specific information—for example, Printer out of paper. Take the

appropriate action to resolve the problem.

Hard-disk drive

configuration error

The hard drive failed initialization.

Hard-disk drive

controller failure

The hard drive failed initialization.

Hard-disk drive

failure

The hard drive failed initialization.

Hard-disk drive

read failure

The hard drive failed initialization.

Invalid

configuration

information-please

run SETUP

program

The computer configuration information does not match the hardware

configuration.

Invalid Memory

configuration,

please populate

DIMM1

DIMM1 slot does not recognize a memory module. The module should be re-

seated or installed.

Error Message Description

Keyboard failure A cable or connector may be loose, or the keyboard or keyboard/mouse controller

may be faulty.

Memory address

line failure at

address, read value

expecting value

A memory module may be faulty or improperly seated. Reinstall the memory

modules and, if necessary, replace them.

Memory allocation

error

The software you are attempting to run is conflicting with the operating system,

another program, or a utility.

Memory data line

failure at address,

read value

expecting value

A memory module may be faulty or improperly seated. Reinstall the memory

modules and, if necessary, replace them.

Memory double

word logic failure

at address, read

value expecting

value

A memory module may be faulty or improperly seated. Reinstall the memory

modules and, if necessary, replace them.

Memory odd/even

logic failure at

address, read value

expecting value

A memory module may be faulty or improperly seated. Reinstall the memory

modules and, if necessary, replace them

Memory write/read

failure at address,

read value

expecting value

A memory module may be faulty or improperly seated. Reinstall the memory

modules and, if necessary, replace them.

Memory size in

CMOS invalid

The amount of memory recorded in the computer configuration information does

not match the memory installed in the computer.

Memory tests

terminated by

keystroke

A keystroke interrupted the memory test.

No boot device

available

The computer cannot find the floppy disk or hard drive.

No boot sector on

hard-disk drive

The computer configuration information in System Setup may be incorrect.

No timer tick

interrupt

A chip on the system board might be malfunctioning.

Non-system disk

or disk error

The floppy disk in drive A does not have a bootable operating system installed on it.

Either replace the floppy disk with one that has a bootable operating system, or

remove the floppy disk from drive A and restart the computer.

Not a boot diskette The operating system is trying to boot to a floppy disk that does not have a

bootable operating system installed on it. Insert a bootable floppy disk.

Error Message Description

Plug and play

configuration error

The computer encountered a problem while trying to configure one or more cards.

Read fault The operating system cannot read from the floppy or hard drive, the computer

could not find a particular sector on the disk, or the requested sector is defective.

Requested sector

not found

The operating system cannot read from the floppy or hard drive, the computer

could not find a particular sector on the disk, or the requested sector is defective.

Reset failed The disk re-set operation failed.

Sector not found The operating system cannot locate a sector on the floppy or hard drive.

Seek error The operating system cannot find a specific track on the floppy disk or hard drive.

Shutdown failure A chip on the system board might be malfunctioning.

Time-of-day clock

stopped

The battery might be dead.

Time-of-day not

set-please run the

System Setup

program

The time or date stored in System Setup does not match the computer clock.

Timer chip counter

2 failed

A chip on the system board may be malfunctioning.

Unexpected

interrupt in

protected mode

The keyboard controller may be malfunctioning or a memory module may be

loose.

WARNING: Dell's

Disk Monitoring

System has

detected that drive

[0/1] on the

[primary/

secondary] EIDE

controller is

operating outside

of normal

specifications. It is

advisable to

immediately back

up your data and

replace your hard

drive by calling

your support desk

or Dell.

During initial startup, the drive detected possible error conditions. When your

computer finishes booting, immediately back up your data and replace your hard

drive (for installation procedures, see "Adding and Removing Parts" for your

computer type). If no replacement drive is immediately available and the drive is

not the only bootable drive, enter System Setup and change the appropriate drive

setting to None. Then remove the drive from the computer.

Write fault The operating system cannot write to the floppy or hard drive.

Write fault on

selected drive

The operating system cannot write to the floppy or hard drive.

Specifications

NOTE: Offerings may vary by region. For more information regarding the configuration of your

computer, click Start (Start icon) → Help and Support, and then select the option to view

information about your computer.

Table 15. Processor

Feature Specification

Processor type • Intel Core i3/i5/i7 series

• Intel Dual Core series

Total Cache Up to 8 MB cache depending on processor type

Table 16. Memory

Feature Specification

Type DDR3

Speed 1600MHz

Connectors:

Mini-Tower, Small Form Factor four DIMM slots

Capacity 2 GB, 4 GB, and 8 GB

Minimum Memory 2 GB

Maximum memory 16 GB

Table 17. Video

Feature Specification

Integrated Intel HD Graphics 4600 (i3/i5/i7 DC/QC Intel 8 Series

Express chipset CPU-GPU Combo) and Intel HD

Graphics ( Pentium CPU-GPU)

Discrete PCI Express x16 graphics adapter

Table 18. Audio

Feature Specification

Integrated two channel High Definition Audio

Table 19. Network

Feature Specification

Integrated Intel I217LM Ethernet capable of 10/100/1000 Mb/s

communication

Table 20. System Information

Feature Specification

System chipset Intel 8 series Express chipset

DMA Channels two 8237 DMA controllers with seven independently

programmable channels

Interrupt Levels Integrated I/O APIC capability with 24 interrupts

BIOS Chip (NVRAM) 12 MB

Table 21. Expansion Bus

Feature Specification

Bus Type PCIe gen2, gen3 (x16), USB 2.0, and USB 3.0

Bus Speed PCI Express:

• x1-slot each direction speed –500 MB/s

• x16-slot each direction speed–16 GB/s

SATA: 1.5 Gbps, 3.0 Gbps, and 6 Gbps

Table 22. Cards

Feature Specification

PCI:

Mini-Tower up to one full-height card

Small Form Factor none

PCI Express x1:

Mini-Tower up to three full-height cards

Small Form Factor up to two low-profile cards

PCI-Express x16:

Mini-Tower up to two full-height cards

Small Form Factor up to two low-profile cards

Table 23. Drives

Feature Specification

Externally Accessible (5.25-inch drive bays):

Mini-Tower two

Feature Specification

Small Form Factor one slim-optical drive bay

Internally Accessible

3.5-inch SATA

drive bays:

Mini-Tower two

Small Form Factor one

2.5-inch SATA

drive bays:

Mini-Tower two

Small Form Factor two

Table 24. External Connectors

Feature Specification

Audio:

Front Panel • one microphone connector

• one headphone connector

Back Panel • one line-out connector

• one line-in/microphone connector

Network Adapter one RJ45 connector

Serial one 9-pin connector; 16550 C compatible

Parallel one 25-pin connector (optional for minitower and small

form factor)

USB 2.0: • Front Panel: two

• Back Panel: four

USB 3.0: • Front Panel: two

• Back Panel: two

Video • 15-pin VGA connector

• two 20-pin DisplayPort connectors

NOTE: Available video connectors may vary based

on the graphics card selected.

Table 25. Internal Connectors

Feature Specification

PCI 2.3 data width (maximum) – 32 bits

Mini-Tower one 120-pin connector

Feature Specification

Small Form Factor none

PCI Express x1 data width (maximum) – one PCI Express lane

Mini-Tower one 36-pin connector

Small Form Factor none

PCI Express x16 (wired as x4) data width (maximum) – four PCI Express lanes

Mini-Tower one 164-pin connector

Small Form Factor one 64-pin connector

PCI Express x16 data width (maximum) – 16 PCI Express lanes

Mini-Tower, Small Form Factor one 164-pin connector

Mini PCI Express data width (maximum) – one PCI Express lane and one USB interface

Mini-Tower, Small Form Factor none

Serial ATA:

Mini-Tower four 7-pin connectors

Small Form Factor three 7-pin connectors

Memory:

Mini-Tower, Small Form Factor four 240-pin connectors

Internal USB:

Mini-Tower one 10-pin connector

Small Form Factor none

System Fan one 5-pin connector

Front panel control:

Mini-Tower • one 6–pin connector

• two 20–pin connector

Small Form Factor • one 6-pin connector

• one 10-pin connector

• one 12-pin connector

• one 20-pin connector

Thermal Sensor:

Mini-Tower one 2-pin connector

Small Form Factor none

Processor one 1150-pin connector

Processor Fan one 5-pin connector

Service mode jumper one 2-pin connector

Feature Specification

Password clear jumper one 2-pin connector

RTC reset jumper one 2-pin connector

Internal speaker one 5-pin connector

Intruder connector one 3-pin connector

Power connector:

Mini-Tower, Small Form Factor one 8-pin, one 4-pin, one 6-pin,

connector

Table 26. Controls and Lights

Feature Specification

Front of the computer:

Power button light White light — Solid white light indicates power-on state;

blinking white light indicates sleep state of the

computer.

Drive activity light White light — Blinking white light indicates that the

computer is reading data from or writing data to the

hard drive.

Back of the computer:

Link integrity light on integrated network

adapter

Green — a good 10 Mbps connection exists between the

network and the computer.

Green — a good 100 Mbps connection exists between

the network and the computer.

Orange — a good 1000 Mbps connection exists between

the network and the computer.

Off (no light) — the computer is not detecting a physical

connection to the network.

Network activity light on integrated

network adapter

Yellow light — A blinking yellow light indicates that

network activity is present.

Power supply diagnostic light Green light — The power supply is turned on and is

functional. The power cable must be connected to the

power connector (at the back of the computer) and the

electrical outlet.

Table 27. Power

NOTE: Heat dissipation is calculated by using the power supply wattage rating.

Wattage Maximum Heat

Dissipation Voltage

Mini-Tower 290 W 989.00 BTU/hr 100 VAC to 240 VAC, 50 Hz

to 60 Hz, 5 A

Small Form Factor 255 W 870.00 BTU/hr 100 VAC to 240 VAC, 50 Hz

to 60 Hz, 4.4 A

Coin-cell battery 3 V CR2032 lithium coin cell

Table 28. Physical Dimension

Height Width Depth Weight

Mini-Tower 36.00 cm (14.17

inches)

17.50 cm (6.89

inches)

41.70 cm (16.42 inches) 9.40 kg

(20.72 lb)

Small Form

Factor

29.00 cm (11.42

inches)

9.30 cm (3.66

inches)

31.20 cm (12.28 inches) 6.00 kg

(13.22 lb)

Table 29. Environmental

Feature Specification

Temperature range:

Operating 5 °C to 35 °C (41 °F to 95 °F)

Storage –40 °C to 65 °C (–40 °F to 149 °F)

Relative humidity (maximum):

Operating 20 percent to 80 percent (non-condensing)

Storage 5 percent to 95 percent (non-condensing)

Maximum vibration:

Operating 0.26 GRMS

Storage 2.20 GRMS

Maximum shock:

Operating 40 G

Storage 105 G

Altitude:

Operating –15.2 m to 3048 m (–50 to 10,000 ft)

Storage –15.20 m to 10,668 m (–50 ft to 35,000 ft)

Airborne contaminant level G1 or lower as defined by ANSI/ISA-S71.04-1985

Contacting Dell

NOTE: If you do not have an active Internet connection, you can find contact information on your

purchase invoice, packing slip, bill, or Dell product catalog.

Dell provides several online and telephone-based support and service options. Availability varies by

country and product, and some services may not be available in your area. To contact Dell for sales,

technical support, or customer service issues:

Go to dell.com/contactdell.

Table of Contents

DELL 7020 User Manual

Related Manuals