Table of Contents
- Latitude 7285 2-in-1 Owner's Manual
- System specifications
- Processor specifications
- System specifications
- Memory specifications
- Video specifications
- Audio specifications
- Port and connector specifications
- Communication specifications
- Camera specifications
- Display specifications
- AC adapter specifications
- Battery specifications
- Physical specifications
- Active pen specifications
- Wireless charging mat specifications
- Environmental specifications
- Using your tablet
- Removing and Installing components
- Technology and components
- System setup
- Entering BIOS without keyboard
- System setup options
- General screen options
- System Configuration screen options
- Video screen options
- Security screen options
- Secure Boot screen options
- Intel software guard extensions screen options
- Performance screen options
- Power management screen options
- POST behavior screen options
- Manageability
- Virtualization support screen options
- Wireless screen options
- Maintenance screen options
- System logs screen options
- Updating the BIOS
- System and setup password
- Troubleshooting
- Contacting Dell
DELL 7285 User Manual
Displayed below is the user manual for 7285 by DELL which is a product in the Notebooks category. This manual has pages.
Related Manuals
Latitude 7285 2-in-1
Owner's Manual
Regulatory Model: T02J
Regulatory Type: T02J001
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of your tablet.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2017 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks
may be trademarks of their respective owners.
2017 - 07
Rev. A00
Contents
1 System specications.................................................................................................................................... 6
Processor specications....................................................................................................................................................6
System specications........................................................................................................................................................ 6
Memory specications.......................................................................................................................................................7
Video specications........................................................................................................................................................... 7
Audio specications........................................................................................................................................................... 7
Port and connector specications................................................................................................................................... 7
Communication specications..........................................................................................................................................8
Camera specications........................................................................................................................................................8
Display specications.........................................................................................................................................................8
AC adapter specications................................................................................................................................................. 9
Battery specications........................................................................................................................................................ 9
Physical specications..................................................................................................................................................... 10
Active pen specications................................................................................................................................................. 10
Wireless charging mat specications.............................................................................................................................. 11
Environmental specications............................................................................................................................................11
2 Using your tablet.......................................................................................................................................... 12
Turning o Your Tablet..................................................................................................................................................... 12
Before Working Inside Your Tablet.................................................................................................................................. 13
After working inside your tablet...................................................................................................................................... 14
3 Removing and Installing components............................................................................................................15
microSIM card...................................................................................................................................................................15
microSD card.....................................................................................................................................................................16
Display Panel......................................................................................................................................................................17
Removing the display panel....................................................................................................................................... 17
Installing the display panel.........................................................................................................................................23
Battery...............................................................................................................................................................................23
Removing the battery................................................................................................................................................23
Installing the battery.................................................................................................................................................. 24
Power switch board......................................................................................................................................................... 24
Removing the power button board..........................................................................................................................24
Installing the power button board............................................................................................................................ 25
WLAN card....................................................................................................................................................................... 25
Removing the WLAN card........................................................................................................................................ 25
Installing the WLAN card.......................................................................................................................................... 26
PCIe Solid State Drive (SSD)......................................................................................................................................... 26
Removing the SSD module.......................................................................................................................................26
Installing the SSD module..........................................................................................................................................27
WWAN card......................................................................................................................................................................28
Removing the WWAN card.......................................................................................................................................28
Installing the WWAN card.........................................................................................................................................28
Contents 3
Audio board.......................................................................................................................................................................29
Removing the audio port...........................................................................................................................................29
Installing the audio port.............................................................................................................................................30
Front facing camera.........................................................................................................................................................30
Removing the front camera .....................................................................................................................................30
Installing the front camera.........................................................................................................................................31
Rear facing camera...........................................................................................................................................................31
Removing the rear camera........................................................................................................................................ 31
Installing the rear camera..........................................................................................................................................33
Coin cell battery............................................................................................................................................................... 33
Removing the coin cell battery.................................................................................................................................33
Installing the coin cell battery................................................................................................................................... 34
Docking board.................................................................................................................................................................. 35
Removing the docking board....................................................................................................................................35
Installing the docking board...................................................................................................................................... 35
Thunderbolt over Type-C USB bracket.........................................................................................................................36
Removing the thunderbolt over Type-C bracket................................................................................................... 36
Installing the thunderbolt over Type-C USB bracket.............................................................................................37
System Board................................................................................................................................................................... 37
Removing the system board..................................................................................................................................... 37
Installing the system board....................................................................................................................................... 39
Speaker............................................................................................................................................................................. 39
Removing the speaker...............................................................................................................................................39
Installing the speaker.................................................................................................................................................40
Back cover.........................................................................................................................................................................41
Replacing the back cover.......................................................................................................................................... 41
4 Technology and components........................................................................................................................43
Power adapter..................................................................................................................................................................43
Processors........................................................................................................................................................................ 43
Kaby Lake — 7th Generation Intel Core processors............................................................................................. 43
Chipset.............................................................................................................................................................................. 44
Memory features..............................................................................................................................................................44
Display options..................................................................................................................................................................44
Camera features...............................................................................................................................................................44
Starting the camera...................................................................................................................................................44
Starting the camera application............................................................................................................................... 44
Hard drive options............................................................................................................................................................45
Drivers............................................................................................................................................................................... 46
System drivers............................................................................................................................................................46
Disk driver................................................................................................................................................................... 47
Sound, video and game controller drivers...............................................................................................................48
Storage controller drivers..........................................................................................................................................49
Network drivers......................................................................................................................................................... 50
Graphics driver........................................................................................................................................................... 50
Thunderbolt over Type-C.................................................................................................................................................51
Thunderbolt 3 over Type-C....................................................................................................................................... 51
4Contents
Key Features of Thunderbolt 3 over USB Type-C .................................................................................................51
Thunderbolt Icons......................................................................................................................................................52
Dell Active Pen ................................................................................................................................................................ 53
Wireless charging mat..................................................................................................................................................... 54
5 System setup.............................................................................................................................................. 55
Entering BIOS without keyboard................................................................................................................................... 55
System setup options......................................................................................................................................................55
General screen options..............................................................................................................................................55
System Conguration screen options..................................................................................................................... 56
Video screen options................................................................................................................................................. 58
Security screen options.............................................................................................................................................58
Secure Boot screen options..................................................................................................................................... 60
Intel software guard extensions screen options.....................................................................................................60
Performance screen options..................................................................................................................................... 61
Power management screen options.........................................................................................................................61
POST behavior screen options.................................................................................................................................63
Manageability............................................................................................................................................................. 64
Virtualization support screen options......................................................................................................................64
Wireless screen options.............................................................................................................................................64
Maintenance screen options.................................................................................................................................... 65
System logs screen options......................................................................................................................................65
Updating the BIOS ..........................................................................................................................................................65
System and setup password.......................................................................................................................................... 66
Assigning a system password and setup password...............................................................................................66
Deleting or changing an existing system and/or setup password........................................................................67
6 Troubleshooting........................................................................................................................................... 68
Enhanced Pre-boot System Assessment (ePSA)........................................................................................................68
Features:..................................................................................................................................................................... 68
Running the ePSA Diagnostic Utility ...................................................................................................................... 68
Dell wireless charging mat.............................................................................................................................................. 68
Tablet LED.........................................................................................................................................................................69
Diagnostic LED...........................................................................................................................................................69
Real Time Clock (RTC) reset..........................................................................................................................................69
Identifying the AC adapter shipped with your notebooktablet...................................................................................70
7 Contacting Dell............................................................................................................................................. 71
Contents 5
System specications
NOTE: Oerings may vary by region. The following specications are only those required by law to ship with your computer. For
more information about the conguration of your computer, go to Help and Support in your Windows operating system and
select the option to view information about your computer.
Topics:
• Processor specications
• System specications
• Memory specications
• Video specications
• Audio specications
• Port and connector specications
• Communication specications
• Camera specications
• Display specications
• AC adapter specications
• Battery specications
• Physical specications
• Active pen specications
• Wireless charging mat specications
• Environmental specications
Processor specications
Feature Specication
Types • 7th Generation Intel Core i5-7Y54 (4M Cache, up to 3.2 GHz) supports Windows 10 only
• 7th Generation Intel Core i5-7Y57 (4M Cache, up to 3.30 GHz), vPro supports Windows 10 only
• 7th Generation Intel Core i7-7Y75 (4M Cache, up to 3.60 GHz), vPro supports Windows 10 only
System specications
Feature Specication
Chipset Integrated in the processor
DRAM bus width 64-bit; 2 channels
1
6 System specications
Memory specications
Feature Specication
Memory connector Onboard memory
Memory capacity 8 GB and 16 GB (on board)
Memory type LPDDR3—1866 MHz
Video specications
Feature Specication
Type Integrated on system board
UMA controller Intel Integrated HD Graphics 615
External display
support
Optional Dell Adapter - USB Type-C to HDMI/VGA/ Ethernet/USB 3.0/DisplayPort
NOTE: Supports VGA, DisplayPort, HDMI through the docking station.
Audio specications
Feature Specication
Types High-denition audio
Controller Realtek ALC3253
Stereo conversion 24-bit—analog-to-digital and digital-to-analog
Internal interface High-denition audio
External interface Microphone-in, stereo headphones, and speakers universal connector
Speakers Two
Internal speaker
amplier
2 W (RMS) per channel
Volume controls Volume up and Volume down buttons
Port and connector specications
Feature Specication
Audio • Realtek ALC3253-CG Controller
• Microphone-in and stereo headphones/speakers universal connector
Video • Two DisplayPorts over USB Type-C
Memory card reader microSD 3.0
Micro Subscriber
Identity Module
(uSIM) card
Optional
System specications 7
Feature Specication
USIM Optional micro-SIM card slot
Security Lock Noble Wedge Lock slot
Other • Windows Home Button
• Power Button
• I2C for the Dock Pin Keyboard connection
Communication specications
Features Specication
Wireless LAN Intel Dual-Band Wireless-AC 8265 Wi-Fi + BT 4.2 Wireless Card (2x2). Bluetooth Optional
Mobile Broadband
(Optional) • Dell Wireless Qualcomm Snapdragon X7 LTE-A (DW5811e) for AT&T, Verizon, & Sprint (US)
• Dell Wireless Qualcomm Snapdragon X7 LTE-A (DW5811e) (EMEA/ROW)
• Dell Wireless Qualcomm Snapdragon X7 HSPA+ (DW5811e) (China/Indonesia/India)
• Dell Wireless Qualcomm Snapdragon X7 LTE-A (DW5816e for Japan)
WiGig (Optional) Intel Tri-Band Wireless-AC 18265 WiGig + Wi-Fi + BT4.2 Wireless Card WiFi Display (Miracast)
Camera specications
Feature Specication
Type • Front Camera- 720P xed focus
• Rear Camera- 8MP auto focus
• IR Camera- VGA IR camera
Sensor type CMOS sensor technology (Front and Rear camera)
Imaging rate Up to 30 frames per second
Video Resolution • Front Camera- 1280 x 720 pixels
• Rear Camera- 3264 x 2448 pixels
Display specications
Feature Specication
Type 12.3" 3:2 Touch with Corning Gorilla Glass 4 Antireective, and Antismudge
Luminance 400 nits
Height 10.37 inches ( 263.50 mm)
Width 7.28 inches ( 185.06 mm)
Diagonal 12.0 inches (312.42 mm)
Maximum resolution 2880 x 1920
Refresh rate 60 Hz
8 System specications
Feature Specication
Maximum viewing
angles—horizontal
+/-80°
Maximum viewing
angles—vertical
+/-80°
Pixel pitch 0.135 mm
AC adapter specications
Feature Specication
Type 45 W USB Type-C
Input voltage 100 V AC–240 V AC
Input current—
maximum
1.5 A
Input frequency 50 Hz to 60 Hz
Output current 3.34 A (continuous)
Rated output
voltage
20 VDC
Weight 0.64 lbs (0.29 kg)
Dimensions • 1.1 x 1.9 x 4.3 inches
• 28 x 47 x 108 mm
Temperature range
—Operating
0°C to 40°C (32°F to 104°F)
Temperature range
—Non-Operating
–40°C to 70°C (–40°F to 158°F)
Battery specications
Feature Specication
Type • 34 Whr Polymer battery with ExpressCharge
• 34 Whr Long Life Cycle Battery (2-cell)
34 Whr Polymer
battery with
ExpressCharge:
Length 184.00 mm (7.24 inches)
Width 97.00 mm (3.82 inches)
Height 5.9 mm (0.232 inch)
Weight 185.0 g (0.40 lb)
Voltage 11.4 VDC
System specications 9
Feature Specication
34 Whr Long Life
Cycle Battery (2-
cell):
Length 233.06 mm (9.170 inches)
Width 90.73 mm (3.572 inches)
Height 5.9 mm (0.232 inch)
Weight 250.00 g (0.55 lb)
Voltage 11.4 VDC
Temperature range
Operating • Charge: 0°C to 50°C (32°F to 122°F)
• Discharge: 0°C to 70°C (32°F to 158°F)
Non-operating - 20°C to 85°C (- 4°F to 185°F)
Life span 300 discharge per charge cycles
Physical specications
Feature Specication
Weight - Tablet only 1.5 lb (0.7kg)
Weight - Tablet
+Keyboard
3.01 lb (1.36 kg)
Width 10.8 inches (274.8 mm)
Height 0.3 inch (7.9 mm)
Depth 8.2 inches (209.2 mm)
Active pen specications
Feature Specication
Model number PN557W
Length 6.33 inches (160.6 mm)
Diameter 0.37 inch (9.5 mm)
Pressure Resolution 2048 levels
Accuracy/Resolution • Pen contact accuracy is 0.2 mm at 0° tilt; < 0.4 mm at up to 60° tilt in either stationary or in motion state
• Pen hover accuracy is less than 2 mm within hovering height of more or equal to 10 mm in either stationary or
in motion state
Weight (including
battery)
20.4 g with batteries
Battery • Stylus: Primary non- rechargeable AAAA alkaline (1x)
• End cap: 319 lithium coin cell (2x)
10 System specications
Feature Specication
Battery life • Primary AAAA: 12 months for 3 hours/day, 5 days/week
• 319 coin cell (2x): 12 months or more
Stylus Tip • Tip — 0.11 inch (2.8 mm)
• Diameter —0.07 inch (1.8 mm)
Wireless charging mat specications
Feature Specication
Model Number PM30W17
PTU Rated Power 20W (AirFuel mode)
30W (Dell on Dell mode)
Weight 645 g (Charging Mat only)
Dimension:
Legnth 12.28 inch (312.00 mm)
Width 11.17 inch (283.82 mm)
Height 0.69 inch (17.73 mm)
DC Cable length 2.0 m
AC Cable length 1.0 m
Environmental specications
Temperature Specications
Operating 0°C to 35°C (32°F to 95°F)
Storage –40°C to 65°C (–40°F to 149°F)
Relative humidity
—maximum
Specications
Operating 10% to 90% (non-condensing)
Storage 10% to 95% (non-condensing)
Altitude—
maximum
Specications
Operating 0 m to 3048 m (0 to 10,000 ft)
Non-operating 0 m to 10,668 m (0 ft to 35,000 ft)
Airborne
contaminant level
G2 or lower as dened by ISA S71.04–1985
System specications 11
Using your tablet
This section covers how to power on and turn o your tablet including how to install the micro SD and micro SIM cards.
Topics:
• Turning o Your Tablet
• Before Working Inside Your Tablet
• After working inside your tablet
Turning o Your Tablet
Turning o your tablet completely shuts down your tablet. You can turn o your tablet by two ways:
• Using power button
• Using charms menu
1 To turn o your tablet using power button:
a Press and hold the Power button until you see “Slide to shut down your PC” on the screen.
NOTE: After you press and hold the Power button, by default, the tablet enters sleep mode. However, if you
change the power button setting to shut down, the tablet shuts down. To change the power button setting,
go to Control Panel > Power Options > Change Plan Setting > Change Advanced Power Settings. To access
Control Panel, swipe at the right edge of the screen, tap Search, enter Control Panel in the search box, and
then click Control Panel.
b Slide to shut down your tablet.
2
12 Using your tablet
NOTE: You can also turn o your tablet without sliding down the screen. Press and hold the Power button for
>10 seconds to turn o your tablet. You can perform this force shutdown, if your tablet is not responding / behaving
unexpectedly or touch is not working.
2 To turn o your tablet using the charms menu:
a Swipe from the right edge of the display to access the Charms menu.
b Touch Settings —> Power —> Shut down to turn o the tablet.
Before Working Inside Your Tablet
Use the following safety guidelines to help protect your tablet from potential damage and to help to ensure your personal safety. Unless
otherwise noted, each procedure included in this document assumes that the following condition exists:
• You have read the safety information that shipped with your tablet.
WARNING: Before working inside your tablet, read the safety information that shipped with your tablet. For additional safety
best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance
CAUTION: Many repairs may only be done by a certied service technician. You should only perform troubleshooting and simple
repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage
due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came
with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an
unpainted metal surface, such as a connector on the back of the tablet.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its
edges or by its metal mounting bracket.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have
connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the
cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a
cable, ensure that both connectors are correctly oriented and aligned.
NOTE: The color of your tablet and certain components may appear dierently than shown in this document.
To avoid damaging your tablet, perform the following steps before you begin working inside the tablet.
1 Ensure that your work surface is at and clean to prevent the tablet cover from being scratched.
2 Turn o your tablet (see Turning O Your Tablet).
Using your tablet 13
3 If the tablet is connected to a docking device (docked) such as the optional docking station or keyboard dock, un-dock it.
4 Disconnect the power adapter from the tablet.
5 Press and hold the power button for a few seconds to remove the ea power from the system board.
CAUTION: To guard against electrical shock, always unplug your tablet from the electrical outlet.
CAUTION: Before touching anything inside your tablet, ground yourself by touching an unpainted metal surface, such as
the metal at the back of the tablet. While you work, periodically touch an unpainted metal surface to dissipate static
electricity, which could harm internal components.
6 Remove the storage SD card from the tablet.
After working inside your tablet
NOTE: Leaving stray loose screws inside your table may severely damage your tablet.
1 Replace all screws and ensure that no stray screws remain inside your tablet.
2 Connect any external devices, peripherals, and cables that you removed before working on your tablet.
3 Replace any media card, SIM card, and any other parts that you removed before working on your tablet.
4 Connect your tablet and all attached devices to their electrical outlets.
5 Turn on your tablet.
14 Using your tablet
Removing and Installing components
This section provides detailed information on how to remove or install the components from your tablet.
Topics:
• microSIM card
• microSD card
• Display Panel
• Battery
• Power switch board
• WLAN card
• PCIe Solid State Drive (SSD)
• WWAN card
• Audio board
• Front facing camera
• Rear facing camera
• Coin cell battery
• Docking board
• Thunderbolt over Type-C USB bracket
• System Board
• Speaker
• Back cover
microSIM card
1 Insert a paperclip or a microSIM card removal tool into the pinhole on the microSIM card tray [1].
2 Insert the microSIM card into the slots indicated on the slot [2].
3 Align the cover with the groove on the tablet and slide it inside to secure the microSIM [3].
3
Removing and Installing components 15
4 You can perform the same steps to remove the microSIM.
microSD card
1 Insert a paperclip or a microSD card removal tool into the pinhole on the microSD card tray [1].
2 Insert the microSD card into the slots indicated on the slot [2].
3 Align the cover with the groove on the tablet and slide it inside to secure the microSD [3].
16 Removing and Installing components
4 You can perform the same steps to remove the microSD.
Display Panel
Removing the display panel
1 Follow the procedure in Before working inside your tablet.
2 Remove the microSIM card and microSD card.
3 To release the display panel (with plastic scribe):
a Remove the M2x4 (4) screws that secure the display panel to the tablet [1].
b Use a plastic scribe to remove the microSIM/microSD cover [2].
Removing and Installing components 17
4 Insert a plastic scribe into the microSIM/microSD slot.
5 Pry the edges starting from microSIM/microSD slot [1, 2].
18 Removing and Installing components
6 To release the display panel (with suction cup):
a Remove the M2x4 (4) screws that secure the display panel to the tablet [1].
b Attach a suction cup to the display panel above the left docking slot, located at the bottom of the system, while inserting a
plastic scribe into the left docking slot to stabilize the system, and then carefully pull open the display panel using the suction
cup.
Removing and Installing components 19
7 Lift the display panel from the tablet.
8 Slide the display panel [1], and ip the display panel [2].
20 Removing and Installing components
CAUTION: Do not open the display panel more than 90 degrees as this may damage the display cable.
9 Before removing display panel:
a Gently place the bottom edge of the display panel inside the bottom edge of the rear cover.
b Flip open the display panel to a 180 degree angle and lay it at on the surface.
10 To disconnect the display cable:
a Remove the M1.6x2.5 (1) screw that secures the metal bracket on the system board [1].
b Lift the metal tab and disconnect the battery cable [2].
c Remove the adhesive tape that secure the display cable on the system board [3].
d Remove the M1.6x2.5 (2) screws that secures display cable [4].
Removing and Installing components 21
e Lift the metal tab from the system board [5].
f Lift the tab and disconnect the display cable [6].
NOTE: Only disconnect the display cable from the system board. DO NOT disconnect the display cable from the display
panel.
11 Remove the display panel from the tablet.
22 Removing and Installing components
Installing the display panel
1 Place the display panel on a plane surface.
2 Connect the display cable to the connector on the system boar
NOTE: Make sure to insert the cable under the clips, if not, the system may not display video after reassembling.
3 Place the metal bracket and replace the M1.6x2.5 (2) screws to secure the display panel.
4 Connect the battery cable to the connector on the system board.
5 Place the metal bracket and replace the M1.6x2.5 (1) screw that secures the connector on the system board.
6 Install the display panel on the tablet and press the edges until they snap-in.
7 Replace the M2x4 (4) screws to secure the tablet to the display panel.
8 Install microSIM card and microSD card.
9 Follow the procedure in After working inside your tablet.
Battery
Removing the battery
1 Follow the procedure in Before working inside your tablet.
2 Remove the:
amicroSIM card and microSD card
bdisplay panel
3 To remove the battery:
a Remove the M2x3 (4) screws that secure the battery to the tablet [1].
b Lift the battery from the tablet [2].
Removing and Installing components 23
NOTE: Once the battery cable is disconnected, practice caution not to damage the battery connector on the system
board. The pins of the battery connector are extremely fragile, be careful not to bend the pins.
NOTE: For defective system boards, technicians must always ensure that they attach the battery connector cap when
re-packaging it for return.
Installing the battery
1 Insert the battery into the slot on the tablet.
2 Replace the M2x3 (4) screws to secure the battery to the tablet.
3 Install the:
adisplay panel
bmicroSIM card and microSD card
4 Follow the procedure in After working inside your tablet.
Power switch board
Removing the power button board
1 Follow the procedure in Before working inside your tablet.
2 Remove the:
amicroSIM card and microSD card
bdisplay panel
cbattery
3 To remove the power button board:
a Lift the latch and disconnect the power button cable from the tablet [1].
24 Removing and Installing components
b Remove the M2x1.5 (2) screws that secure the power button board on the tablet [2].
c Slide and remove the power button board from the tablet [3].
Installing the power button board
1 Insert the power button board into the slot on the tablet.
2 Replace the M2x1.5 (2) screws to secure the power button board to the tablet.
3 Connect the power button board cable and close the latch on the tablet.
4 Install the:
abattery
bdisplay panel
cmicroSIM card and microSD card
5 Follow the procedure in After working inside your tablet.
WLAN card
Removing the WLAN card
1 Follow the procedure in Before working inside your tablet.
2 Remove the:
amicroSIM card and microSD card
bdisplay panel
cbattery
3 To remove the WLAN card:
Removing and Installing components 25
a Remove the M2x2.0 (1) screw securing the WLAN bracket [1].
b Lift the WLAN bracket away from the system board [2].
c Disconnect the antenna cables from the WLAN card [3].
d Slide and lift the WLAN card from the connector on the system board 4].
Installing the WLAN card
1 Insert the WLAN card into the connector on the system board.
2 Connect the antenna cables to the WLAN card.
3 Insert the WLAN bracket to the WLAN card.
4 Replace the M2x2.0 (1) screw to secure the WLAN bracket.
5 Install the:
abattery
bdisplay panel
cmicroSIM card and microSD card
6 Follow the procedure in After working inside your tablet.
PCIe Solid State Drive (SSD)
Removing the SSD module
1 Follow the procedure in Before working inside your tablet.
2 Remove the:
amicroSIM card and microSD card
26 Removing and Installing components
bdisplay panel
cbattery
3 To remove the SSD module:
a Remove the M2x2.0 (1) screw securing the SSD shield [1].
b Lift the SSD shield away from the tablet [2].
c Slide and lift the SSD module from the slot on the tablet [3].
Installing the SSD module
1 Insert the SSD module into the connector on the system board.
2 Install the SSD shield on the SSD module.
3 Replace the M2x2.0 (1) screw to secure SSD shield.
NOTE: Align the shield carefully or else it may break.
4 Install the:
abattery
bdisplay panel
cmicroSIM card and microSD card
5 Follow the procedure in After working inside your tablet.
Removing and Installing components 27
WWAN card
Removing the WWAN card
1 Follow the procedure in Before working inside your tablet.
2 Remove the:
amicroSIM card and microSD card
bdisplay panel
cbattery
3 To remove the WWAN card:
a Remove the M2x2.0 (1) screw securing the WWAN bracket [1].
b Lift the WWAN bracket from the tablet [2].
c Disconnect the antenna cables from the WWAN card [3].
d Slide and lift the WWAN card from the connector on the system board [4].
Installing the WWAN card
1 Insert the WWAN card into the connector on the system board.
2 Connect the antenna cables to the WWAN card.
3 Insert the WLAN bracket to the WWAN card.
28 Removing and Installing components
4 Replace the M2x2.0 (1) screw to secure WWAN bracket.
5 Install the:
abattery
bdisplay panel
cmicroSIM card and microSD card
6 Follow the procedure in After working inside your tablet.
Audio board
Removing the audio port
1 Follow the procedure in Before working inside your tablet.
2 Remove the:
amicroSIM card and microSD card
bdisplay panel
cbattery
3 To remove the audio port:
a Lift the latch and disconnect the audio port connector [1].
b Peel the audio port cable from the tablet [2].
c Remove the M2X3 (2) screw that secures the audio port on the system board [3].
d Lift the audio port from the system board [4].
Removing and Installing components 29
Installing the audio port
1 Place and insert the audio port into the connector on the system board.
2 Replace the M2X3 (2) screw to secure audio port on the system board.
3 Ax the audio port on the system board.
4 Connect the audio port cable to the connector.
5 Install the:
abattery
bdisplay panel
cmicroSIM card and microSD card
6 Follow the procedure in After working inside your tablet.
Front facing camera
Removing the front camera
1 Follow the procedure in Before working inside your tablet.
2 Remove the:
amicroSIM card and microSD card
bdisplay panel
cbattery
3 To remove the front facing camera:
a Lift the latch and disconnect the camera connector [1].
b Remove the M1.6x2.5 (2) screws that secure the camera on the system board [2].
c Lift the front camera from the tablet [3].
30 Removing and Installing components
Installing the front camera
1 Insert the camera module into the slot on the tablet.
2 Replace the M1.6x2.5 (2) screws to secure the front camera module.
3 Connect the front camera cable to the system board..
4 Install the:
abattery
bdisplay panel
cmicroSIM card and microSD card
5 Follow the procedure in After working inside your tablet.
Rear facing camera
Removing the rear camera
1 Follow the procedure in Before working inside your tablet.
2 Remove the:
Removing and Installing components 31
amicroSIM card and microSD card
bdisplay panel
cbattery
3 To disconnect front camera cable:
a Lift the latch and disconnect the front camera cable [1].
b Remove the front camera cable from the system board [2].
4 To remove the rear camera:
a Disconnect the rear camera cable from the system board [1].
b Remove the M1.6x2.5 (1) screw securing the rear camera module [2].
c Lift the camera module from the tablet [3].
32 Removing and Installing components
Installing the rear camera
1 Insert the rear camera module into the slot on the tablet.
2 Replace the M1.6x2.5 (1) screw to secure the rear camera module.
3 Connect the rear camera cable to the system board.
4 Connect the front camera cable to the system board.
5 Install the:
abattery
bdisplay panel
cmicroSIM card and microSD card
6 Follow the procedure in After working inside your tablet.
Coin cell battery
Removing the coin cell battery
1 Follow the procedure in Before working inside your tablet.
2 Remove the:
amicroSIM card and microSD card
bdisplay panel
Removing and Installing components 33
cbattery
dfront facing camera
3 To remove the coin cell battery:
a Disconnect the coin cell battery cable from the connector on the system board [1].
b Pry the coin cell battery to release from the adhesive and lift it away from the system board [2].
Installing the coin cell battery
1 Place the coin cell battery into the slot on the system board.
2 Connect the coin cell battery cable to the connector on the system board.
3 Install the:
afront facing camera
bbattery
cdisplay panel
dmicroSIM card and microSD card
4 Follow the procedure in After working inside your tablet.
34 Removing and Installing components
Docking board
Removing the docking board
1 Follow the procedure in Before working inside your tablet.
2 Remove the:
amicroSIM card and microSD card
bdisplay panel
cbattery
3 To release the docking board:
a Disconnect the docking board cable from the system board [1].
b Remove the M1.6x4 (2) screws securing the docking board bracket to the docking board [2].
c Remove the docking board bracket [3].
d Lift the docking board from the tablet [4].
Installing the docking board
1 Insert the docking board into the slot on the tablet.
2 Place the docking board metal on the docking board.
Removing and Installing components 35
3 Replace the M1.6x4 (2) screws to secure the docking board to the tablet.
4 Connect the docking board cable to the connector on the system board.
5 Install the:
abattery
bdisplay panel
cmicroSIM card and microSD card
6 Follow the procedure in After working inside your tablet.
Thunderbolt over Type-C USB bracket
Removing the thunderbolt over Type-C bracket
1 Follow the procedure in Before working inside your tablet.
2 Remove the:
amicroSIM card and microSD card
bdisplay panel
cbattery
3 To release the thunderbolt over Type-C bracket:
a Remove the M2x2.0 (3) screws securing the thunderbolt over Type-C bracket to the tablet [1].
b Slide and lift the thunderbolt over Type-C bracket from the tablet [2].
36 Removing and Installing components
Installing the thunderbolt over Type-C USB bracket
1 Insert the thunderbolt over Type-C USB bracket into the slot on the tablet.
2 Replace the M2x2.0 (3) screws to secure the thunderbolt over Type-C USB bracket to the tablet.
3 Install the:
abattery
bdisplay panel
cmicroSIM card and microSD card
4 Follow the procedure in After working inside your tablet.
System Board
Removing the system board
NOTE: Heat sink is not a separate service part but is included with the system board. Do not remove the heat sink from the
system board
1 Follow the procedure in Before working inside your tablet.
2 Remove the:
amicroSIM card and microSD card
bdisplay panel
cbattery
dWLAN card
eSSD card
fWWAN card
gfront camera
hrear camera
icoin cell battery
jthunderbolt over Type-C USB bracket
3 Disconnect the following cables from the system board:
a power button cable [1]
b USH board cable [2]
c audio board cable [3]
d docking board cable [4]
e USH board cable [5]
Removing and Installing components 37
4 To remove system board:
a Remove the M1.6x1.5 (4) screw that secures the system board to the tablet [1].
b Lift the system board from the tablet [2].
38 Removing and Installing components
Installing the system board
1 Align the system board with the screw holders on the tablet.
2 Replace the M1.6x1.5 (4) screws to secure the system board to the tablet.
3 Connect the USH board cable, docking board cable, audio board cable, power button cable to the connectors on the system board.
4 Install the:
athunderbolt over Type-C USB bracket
bcoin cell battery
crear camera
dfront camera
eWWAN card
fSSD card
gWLAN card
hbattery
idisplay panel
jmicroSIM card and microSD card
5 Follow the procedure in After working inside your tablet.
Speaker
Removing the speaker
1 Follow the procedure in Before working inside your tablet.
2 Remove the:
amicroSIM card and microSD card
bdisplay panel
cbattery
dWLAN card
eSSD card
fWWAN card
gfront camera
hrear camera
icoin cell battery
jthunderbolt over Type-C USB bracket
ksystem board
3 Unroute the WLAN cable from the speaker retension clip [1,2,3].
Removing and Installing components 39
4 To remove the speaker:
a Peel the speaker adhesive cable from the tablet [1].
b Lift the speaker from the tablet [2].
Installing the speaker
1 Align the speaker with the holders on the tablet.
2 Ax the speaker adhesive tape on the tablet.
40 Removing and Installing components
3 Route the WLAN cable through the retention clips on the tablet.
4 Install the:
asystem board
bthunderbolt over Type-C USB bracket
ccoin cell battery
drear camera
efront camera
fWWAN card
gSSD card
hWLAN card
ibattery
jdisplay panel
kmicroSIM card and microSD card
5 Follow the procedure in After working inside your tablet.
Back cover
Replacing the back cover
1 Follow the procedure in Before working inside your tablet.
2 Remove the:
amicroSIM card and microSD card
bdisplay panel
cbattery
dpower button board
eWLAN card
fSSD card
gWWAN card
haudio port
ifront camera
jrear camera
kcoin cell battery
lDocking board
mthunderbolt over Type-C USB bracket
nsystem board
3 The component you are left with is the back cover.
Removing and Installing components 41
4 Install the following component:
asystem board
bthunderbolt over Type-C USB bracket
cdocking board
dcoin cell battery
erear camera
ffront camera
gaudio port
hWWAN card
iSSD card
jWLAN card
kpower button board
lbattery
mdisplay panel
nmicroSIM card and microSD card
5 Follow the procedure in After working inside your tablet.
42 Removing and Installing components
Technology and components
This chapter details the technology and components available in the system.
Topics:
• Power adapter
• Processors
• Chipset
• Memory features
• Display options
• Camera features
• Hard drive options
• Drivers
• Thunderbolt over Type-C
• Dell Active Pen
• Wireless charging mat
Power adapter
This system is shipped with 45 W Type-C power adapter.
WARNING: When you disconnect the power adapter cable from the tablet, grasp the connector, not the cable itself, and then
pull rmly but gently to avoid damaging the cable.
WARNING: The power adapter works with electrical outlets worldwide. However, power connectors and power strips vary among
countries. Using an incompatible cable or improperly connecting the cable to the power strip or electrical outlet may cause re or
equipment damage.
Processors
Kaby Lake — 7th Generation Intel Core processors
The 7th Gen Intel Core processor (Kaby Lake) family is the successor of 6th generation processors (Skylake). It's main features include:
• Intel 14nm Manufacturing Process Technology
• Intel Turbo Boost Technology
• Intel Hyper Threading Technology
• Intel Built-in Visuals
• Intel HD graphics - exceptional videos, editing smallest details in the videos
• Intel Quick Sync Video - excellent video conferencing capability, quick video editing and authoring
• Intel Clear Video HD - visual quality and color delity enhancements for HD playback and immersing web browsing
• Integrated memory controller
• Intel Smart Cache
4
Technology and components 43
• Optional Intel vPro technology (on i5/i7) with Active Management Technology 11.6
• Intel Rapid Storage Technology
NOTE: Windows 7 and 8 are not supported by systems with 7th generation processors
Chipset
The chipset is integrated on the processor.
Memory features
Latitude 7285 2-in-1 supports the following memory congurations:
• 8 GB 1866MHz LPDDR3
• 16 GB 1866MHz LPDDR3
Display options
This tablet is shipped with 12.3" 1920x1280 Touch with Corning Gorilla Glass, Antireective and Antismudge display.
Camera features
This system is shipped with front facing camera with 5 MP and rear facing camera with 8 MP
Starting the camera
To start the camera, open an application that uses the camera. For instance, if you tap the Dell webcam central software or the Skype
software that is shipped with the 2-in-1, the camera turns on. Similarly, if you are chatting on the internet and the application requests to
access the webcam, the webcam turns on.
Starting the camera application
1 Tap or click the Windows button and select All apps.
2 Select Camera from the apps list.
44 Technology and components
3 If the Camera App is not available in the apps list, search for it.
Hard drive options
This system supports M.2 SATA SSD, M.2 PCIe NVMe SSD, and M.2 PCIe NVMe SED.
Technology and components 45
Drivers
This section lists the drivers associated with the components shipped with your tablet.
System drivers
Figure 1. System drivers
46 Technology and components
Disk driver
Figure 2. Disk driver
Technology and components 47
Sound, video and game controller drivers
Figure 3. Sound, video, and game controllers
48 Technology and components
Storage controller drivers
Figure 4. Storage controllers
Technology and components 49
Network drivers
Figure 5. Network drivers
Graphics driver
Figure 6. Graphics driver
50 Technology and components
Thunderbolt over Type-C
Thunderbolt is a hardware interface that combines data, video, audio, and power in a single connection. Thunderbolt combines PCI Express
(PCIe) and DisplayPort (DP) into one serial signal, and additionally provides DC power, all in one cable. Thunderbolt 1 and Thunderbolt 2 use
the same connector as miniDP (DisplayPort) to connect to peripherals, while Thunderbolt 3 uses a USB Type-C connector.
Figure 7. Thunderbolt 1 and Thunderbolt 3
1 Thunderbolt 1 and Thunderbolt 2 (using a miniDP connector)
2 Thunderbolt 3 (using a USB Type-C connector)
Thunderbolt 3 over Type-C
Thunderbolt 3 brings Thunderbolt to USB Type-C at speeds up to 40 Gbps, creating one compact port that does it all - delivering the
fastest, most versatile connection to any dock, display or data device like an external hard drive. Thunderbolt 3 uses a USB Type-C
connector/port to connect to supported peripherals.
1 Thunderbolt 3 uses USB Type-C connector and cables - It is compact and reversible
2 Thunderbolt 3 supports speed up to 40 Gbps
3 DisplayPort 1.2 – compatible with existing DisplayPort monitors, devices and cables
4 USB Power Delivery - Up to 130W on supported computers
Key Features of Thunderbolt 3 over USB Type-C
1 Thunderbolt, USB, DisplayPort and power on USB Type-C on a single cable (features vary between dierent products)
2 USB Type-C connector and cables which are compact and reversible
3 Supports Thunderbolt Networking (*varies between dierent products)
4 Supports up to 4K displays
5 Up to 40 Gbps
NOTE: Data transfer speed may vary between dierent devices.
Technology and components 51
Thunderbolt Icons
52 Technology and components
Dell Active Pen
• Natural writing feel for a pen on paper experience
• Industry leading accuracy, built with Wacom feel IT technologies
• Active stylus with hovering and pressure-sensitive tip (2048 levels of pressure)
• Magnetic attach feature with built-in magnet for increased fastening strength
• Removed Pen clip and added Tethering functionality
• Customizable* 2 barrel buttons and Top button
• Quick launch and note taking over lock screen (requires Bluetooth pairing)
• LED light to show Bluetooth pairing status
• 12 months battery life**, with AAAA battery
*Need to install “Active Control Panel” from dell.com/support/drivers
**Based on 3 hours daily usage for 5 days a week
Technology and components 53
Wireless charging mat
• PM30W17 is an AirFuel certied resonant type wireless charging mat.
•Oers easy and convenient charging for notebooks.
• Charge your notebook conveniently by simply placing it on the mat without having to plug in power cables.
• Compatible with selected Dell notebooks.
• Suitable for Category 5 AirFuel certied PRUs.
• Dell-branded products carry a 1-year limited hardware warranty
CAUTION: Do not insert any objects between the keyboard and the wireless charging mat or between the wireless charging mat
and the table. Specically, avoid CD/DVDs, RFID cards/devices, credit cards and other thin metal objects. These devices may be
damaged if they are placed as stated above.
54 Technology and components
System setup
System setup enables you to manage your tabletdesktopnotebook hardware and specify BIOS level options. From the System setup, you
can:
• Change the NVRAM settings after you add or remove hardware
• View the system hardware conguration
• Enable or disable integrated devices
• Set performance and power management thresholds
• Manage your computer security
Topics:
• Entering BIOS without keyboard
• System setup options
• Updating the BIOS
• System and setup password
Entering BIOS without keyboard
1 Press the power button to turn on your tablet.
2 Press and hold the Volume Up button when the Dell logo appears on the screen.
3 When the F12 boot selection menu appears, select BIOS Setup using the Volume Up button.
4 Press the Volume Down button to enter BIOS setup program.
System setup options
NOTE: Depending on the tabletnotebook and its installed devices, the items listed in this section may or may not appear.
General screen options
This section lists the primary hardware features of your computer.
Option Description
System Information Lists the primary hardware features of your computer.
• System Information: Displays BIOS Version, Service Tag, Asset Tag, Ownership Tag, Ownership Date,
Manufacture Date, Express Service Code, the Signed Firmware update—enabled by default
• Memory Information: Displays Memory Installed, Memory Available, Memory Speed, Memory Channels Mode,
Memory Technology
• Processor Information: Displays Processor Type, Core Count, Processor ID, Current Clock Speed, Minimum
Clock Speed, Maximum Clock Speed, Processor L2 Cache, Processor L3 Cache, HT Capable, and 64-Bit
Technology
5
System setup 55
Option Description
• Device Information: Displays M.2 PCIe SSD-0, M.2 PCIe SSD-1Passthrough MAC address, Video Controller,
Video BIOS Version, Video Memory, Panel Type, Native Resolution, Audio Controller, Wi-Fi Device, WiGig
Device, Cellular Device, Bluetooth Device
Battery Information Displays the battery status health and whether the AC adapter is installed.
Boot Sequence Boot sequence:
Windows boot manager (selected by default)
Boot list options:
• Legacy
• UEFI (selected by default)
Advanced Boot
Options
This option allows you the legacy option ROMs to load. The options are:
• Enable Legacy Options ROMs (selected by default)
• Enable Attempt Legacy Boot
• Enable UEFI Network Stack
UEFI Boot Path
Security • Always, except internal HDD (selected by default)
• Always
• Never
Date/Time Allows you to change the date and time.
System Conguration screen options
Option Description
SATA Operation Allows you to congure the internal SATA hard-drive controller. The options are:
• Disabled
• AHCI
• RAID On: (selected by default).
Drives Allows you to congure the SATA drives on board. All drives are enabled by default. The options are:
• M.2 PCI-e SSD-0 (selected by default)
• M.2 PCI-e SSD-1 (selected by default)
SMART Reporting This eld controls whether hard drive errors for integrated drives are reported during system startup. This
technology is part of the SMART (Self-Monitoring Analysis and Reporting Technology) specication. This option is
disabled by default.
• Enable SMART Reporting
USB Conguration This is an optional feature.
This eld congures the integrated USB controller. If Boot Support is enabled, the system is allowed to boot any
type of USB Mass Storage Devices—HDD, memory key, oppy.
If USB port is enabled, device attached to this port is enabled and available for OS.
56 System setup
Option Description
If USB port is disabled, the OS cannot see any device attached to this port.
The options are:
• Enable USB Boot Support (selected by default)
• Enable External USB Port (selected by default)
NOTE: A USB Keyboard and/or mouse connected to the platforms USB ports will continue to function
within BIOS Setup if this options is disabled.
Dell Type-C Dock
Conguration
This eld lets you always allow Dell docks.
Always Allows Dell Docks (selected by default)
Thunderbolt
Adapter
Conguration
The options for Thunderbolt Adapter Conguration are:
• Enable Thunderbolt Technology Support (selected by default)
• Enable Thunderbolt Adapter Boot Support (selected by default)
• Enable Thunderbolt Adapter Pre-boot Modules (selected by default)
• Security Level — No Security
• Security Level — User Authorization (selected by default)
• Security Level — Secure Connect
• Security Level — Display Port Only
Audio This eld enables or disables the integrated audio controller. By default, the Enable Audio option is selected. The
options are:
• Enable Microphone (selected by default)
• Enable Internal Speaker (selected by default)
Keyboard
Illumination
This eld lets you choose the operating mode of the keyboard illumination feature. The keyboard brightness level
can be set from 0% to 100%. The options are:
• Disabled (selected by default)
• Dim
• Bright
Keyboard Backlight
Timeout on AC
The Keyboard Backlight Timeout dims out with AC option. The main keyboard illumination feature is not aected.
Keyboard Illumination will continue to support the various illumination levels. This eld has an eect when the
backlight is enabled. The options are:
• 5 sec
• 10 sec (selected by default)
• 15 sec
• 30 sec
• 1 min
• 5 min
• 15 min
• Never
Keyboard Backlight
Timeout on Battery
The Keyboard Backlight Timeout dims out with the Battery option. The main keyboard illumination feature is not
aected. Keyboard Illumination will continue to support the various illumination levels. This eld has an eect when
the backlight is enabled. The options are:
System setup 57
Option Description
• 5 sec
• 10 sec (selected by default)
• 15 sec
• 30 sec
• 1 min
• 5 min
• 15 min
• Never
Keyboard Backlight
with AC
The Keyboard Backlight with AC option does not aect the main keyboard illumination feature. Keyboard
Illumination will continue to support the various illumination levels. This eld has an eect when the backlight is
enabled. This option is enabled by default.
Unobtrusive Mode This option, when enabled by pressing Fn+F7, turns o all light and sound emissions in the system. To resume
normal operation, press Fn+F7 again. This option is disabled by default.
Miscellaneous
Devices
Allows you to enable or disable the following devices:
• Enable Front Camera (selected by default)
• Enable Secure Digital (SD) card (selected by default)
• Enable Back Camera (selected by default)
• Secure Digital (SD) Card Read-Only Mode
Video screen options
Option Description
LCD Brightness Allows you to set the display brightness depending upon the power source—On Battery and On AC. The LCD
brightness is independent for battery and AC adapter. It can be set using the slider.
NOTE: The video setting is visible only when a video card is installed into the system.
Security screen options
Option Description
Admin Password Allows you to set, change, or delete the administrator (admin) password.
NOTE: You must set the admin password before you set the system or hard drive password. Deleting
the admin password automatically deletes the system password and the hard drive password.
NOTE: Successful password changes take eect immediately.
Default setting: Not set
System Password Allows you to set, change, or delete the system password.
NOTE: Successful password changes take eect immediately.
Default setting: Not set
Strong Password Allows you to enforce the option to always set strong passwords.
58 System setup
Option Description
Default Setting: Enable Strong Password is not selected.
NOTE: If Strong Password is enabled, the Admin and System passwords must contain at least one
uppercase character, one lowercase character and should be at least 8 characters long.
Password
Conguration
Allows you to specify the minimum and maximum password lengths of the Administrator and System passwords.
• min-4—by default, if you want to change, you can increase the number
• max-32—you can decrease the number
Password Bypass Allows you to enable or disable the permission to bypass the System and the Internal HDD password, when they
are set. The options are:
• Disabled (selected by default)
• Reboot bypass
Password Change Allows you to enable the disable permission to the System and Hard Drive passwords when the admin password is
set.
Default setting: Allow Non-Admin Password Changes (selected by default).
Non-Admin Setup
Changes
Allows you to determine whether changes to the setup options are allowed when an Administrator Password is set.
If disabled the setup options are locked by the admin password.
Option "allow wireless switch changes" is not selected by default.
UEFI capsule
rmware updates
This option controls whether the system allows BIOS updates using UEFI capsule update packages. This option is
enabled by default.
TPM 2.0 Security Allows you to enable the Trusted Platform Module (TPM) during POST. The options are:
• TPM On (selected by default)
• Clear
• PPI Bypass for Enable Commands (selected by default)
• PPI Bypass for Disabled Commands
• Attestation enable (selected by default)
• Key storage enable (selected by default)
• SHA-256 (selected by default)
• Disabled
• Enabled (selected by default)
NOTE: To upgrade or downgrade TPM 2.0, download the TPM wrapper tool software.
Computrace Allows you to activate or disable the optional Computrace software The options are:
• Deactivate
• Disable
• Activate (selected by default)
NOTE: The Activate and Disable options will permanently activate or disable the feature and no further
changes are allowed
CPU XD Support Allows you to enable the Execute Disable mode of the processor.
Enable CPU XD Support (selected by default).
System setup 59
Option Description
Admin Setup
Lockout
Allows you to prevent users from entering Setup when an Administrator password is set.
Default Setting: This option is disabled.
Master password
lockout
This option is not enabled by default.
Secure Boot screen options
Option Description
Secure Boot Enable This option enables or disables the Secure Boot feature.
• Disabled (selected by default)
• Enabled
Expert Key
Management
Allows you to manipulate the security key databases only if the system is in Custom Mode. The Enable Custom
Mode option is disabled by default. The options are:
• PK—enabled by default
• KEK
• db
• dbx
If you enable the Custom Mode, the relevant options for PK, KEK, db, and dbx appear. The options are:
• Save to File—Saves the key to a user-selected le
• Replace from File—Replaces the current key with a key from a user-selected le
• Append from File—Adds a key to the current database from a user-selected le
• Delete—Deletes the selected key
• Reset All Keys—Resets to default setting
• Delete All Keys—Deletes all the keys
NOTE: If you disable the Custom Mode, all the changes made are erased and the keys restore to default
settings.
Intel software guard extensions screen options
Option Description
Intel SGX Enable This eld species you to provide a secured environment for running code/storing sensitive information in the
context of the main OS. The options are:
• Disabled
• Enabled
• Software controlled
Default setting: Software controlled
Enclave Memory
Size
This option allows you to set the SGX Enclave Reserve Memory Size. The options are:
• 32 MB
60 System setup
Option Description
• 64 MB
• 128 MB (selected by default)
Performance screen options
Option Description
Multi-Core Support This eld species whether the process has one or all cores enabled. The performance of some applications
improves with the additional cores. This option is enabled by default. Allows you to enable or disable multi-core
support for the processor. The installed processor supports two cores. If you enable Multi-Core Support, two cores
are enabled. If you disable Multi-Core Support, one core is enabled.
• Enable Multi-Core Support
Default setting: The option is enabled.
Intel SpeedStep Allows you to enable or disable the Intel SpeedStep feature.
• Enable Intel SpeedStep
Default setting: The option is enabled.
C-States Control Allows you to enable or disable the additional processor sleep states.
• C states
Default setting: The option is enabled.
Intel TurboBoost Allows you to enable or disable the Intel TurboBoost mode of the processor.
• Enable Intel TurboBoost
Default setting: The option is enabled.
HyperThread
Control
Allows you to enable or disable the Hyper-Threading in the processor.
• Disabled
• Enabled
Default setting: Enabled is selected.
Power management screen options
Option Description
Lid Switch The Lid Switch option is enabled by default.
AC Behavior Allows you to enable or disable the computer from turning on automatically when an AC adapter is connected.
Default setting: Wake on AC is not selected.
Auto On Time Allows you to set the time at which the computer must turn on automatically. The options are:
System setup 61
Option Description
• Disabled (selected by default)
• Every Day
• Weekdays
• Select Days
USB Wake Support Allows you to enable USB devices to wake the system from Standby.
NOTE: This feature is only functional when the AC power adapter is connected. If the AC power
adapter is removed during Standby, the system setup removes power from all the USB ports to
conserve battery power.
• Wake on Dell USB-C dock (selected by default)
Wireless Radio
Control
Allows you to enable or disable the feature that automatically switches from wired or wireless networks without
depending on the physical connection.
• Control WLAN Radio
• Control WWAN Radio
Default setting: The options are disabled.
Peak Shift This option enables you to minimize the AC power consumption during the peak power times of day. After you
enable this option, your system runs only in battery even if the AC is attached.
• Enable peak shift
• Set battery threshold (15% to 100%) - 15 %
Advanced Battery
Charge
Conguration
This option enables you to maximize the battery health. By enabling this option, your system uses the standard
charging algorithm and other techniques, during the non work hours to improve the battery health.
Enable Advanced Battery Charge Mode
Primary Battery
Charge
Conguration
Allows you to select the charging mode for the battery. The options are:
• Adaptive (selected by default)
• Standard—Fully charges your battery at a standard rate.
• ExpressCharge—The battery charges over a shorter time using Dell’s fast charging technology This option is
enabled by default.
• Primarily AC use
• Custom
If Custom Charge is selected, you can also congure Custom Charge Start and Custom Charge Stop.
NOTE: All charging mode may not be available for all the batteries. To enable this option, disable the
Advanced Battery Charge Conguration option.
Battery Slice
Charge
Conguration
The options are:
• Standard
• ExpressCharge (selected by default)
62 System setup
POST behavior screen options
Option Description
Adapter Warnings Allows you to enable or disable the system setup (BIOS) warning messages when you use certain power adapters.
Default setting: Enable Adapter Warnings
Keypad
(Embedded)
Allows you to choose one of two methods to enable the keypad that is embedded in the internal keyboard.
• Fn Key Only (selected by default)
• By Numlock
NOTE: When setup is running, this option has no eect. Setup works in Fn Key Only
mode.
Numlock Enable Allows you to enable the Numlock option when the computer boots.
Enable Network. This option is enabled by default.
Fn Key Emulation Allows you to set the option where the Scroll Lock key is used to simulate the Fn key feature.
Enable Fn Key Emulation (default)
Fn Lock Options Allows you to let hot key combinations Fn + Esc toggle the primary behavior of F1–F12, between their standard
and secondary functions. If you disable this option, you cannot toggle dynamically the primary behavior of these
keys. The available options are:
• Lock Mode Disable/Standard (selected by default)
• Lock Mode Enable/Secondary
Fastboot Allows you to speed up the boot process by bypassing some of the compatibility steps. The options are:
• Minimal (selected by default)
• Thorough
• Auto
Extended BIOS
POST Time
Allows you to create an extra preboot delay. The options are:
• 0 seconds (selected by default)
• 5 seconds
• 10 seconds
Full Screen Log • Enable Full Screen Logo—not enabled
Warnings and errors • Prompt on warnings and errors (selected by default)
• Continue on warnings
• Continue on warnings and errors
Sign of Life
Indication
The options are:
• Enable Sign of Life Audio Indication
• Enable Sign of Life Display Indication (selected by default)
System setup 63
Option Description
• Enable Sign of Life Keyboard Backlight Indication
Manageability
Option Description
USB provision Enable USB provision is not selected by default
MEBX Hotkey Allows you to specify whether the MEBx Hotkey function should enabled during the system boot.
Enable MEBX Hotkey selected by default.
Virtualization support screen options
Option Description
Virtualization Allows you to enable or disable the Intel Virtualization Technology.
Enable Intel Virtualization Technology (selected by default).
VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the additional hardware capabilities provided
by Intel® Virtualization technology for direct I/O.
Enable VT for Direct I/O (selected by default).
Trusted Execution This option species whether a Measured Virtual Machine Monitor (MVMM) can utilize the additional hardware
capabilities provided by Intel Trusted Execution Technology. The TPM Virtualization Technology, and the
Virtualization technology for direct I/O must be enabled to use this feature.
Trusted Execution - disabled by default.
Wireless screen options
Option Description
Wireless Device
Enable
Allows you to enable or disable the internal wireless devices.
• WWAN/GPS
• WLAN/WiGig
• Bluetooth
All the options are enabled by default.
NOTE: IMEI number for WWAN can be found on the outer box or the WWAN card.
64 System setup
Maintenance screen options
Option Description
Service Tag Displays the Service Tag of your computer.
Asset Tag Allows you to create a system asset tag if an asset tag is not already set. This option is not set by default.
BIOS Downgrade This controls ashing of the system rmware to previous revisions. Option 'Allow BIOS downgrade' is enabled by
default.
Data Wipe This eld allows users to erase the data securely from all internal storage devices. Option Wipe on Next boot is not
enabled by default. The following is the list of devices aected:
• Internal SATA HDD/SSD
• Internal M.2 SATA SDD
• Internal M.2 PCIe SSD
• Internal eMMC
BIOS Recovery This eld allows you to recover from certain corrupted BIOS conditions from a recover le on the user primary hard
drive or an external USB key.
• BIOS Recovery from Hard Drive—enabled by default
• BIOS Auto-Recovery
• Always perform integrity check—disabled by default
System logs screen options
Option Description
BIOS Events Allows you to view and clear the System Setup (BIOS) POST events.
Thermal Events Allows you to view and clear the System Setup (Thermal) events.
Power Events Allows you to view and clear the System Setup (Power) events.
Updating the BIOS
It is recommended to update your BIOS (System setup) on replacing the system board or if an update is available. Ensure that your
tabletnotebookdesktop battery is fully charged and connected to a power outlet.
1 Restart the tabletnotebookdesktop.
2 Go to Dell.com/support.
3 Enter the Service Tag or Express Service Code and click Submit.
NOTE: To locate the Service Tag, click Where is my Service Tag?
NOTE: If you cannot nd your Service Tag, click Detect My Product. Proceed with the instructions on
screen.
4 If you are unable to locate or nd the Service Tag, click the Product Category of your tabletnotebookdesktop.
5 Choose the Product Type from the list.
6 Select your tabletnotebookdesktop model and the Product Support page of your tabletnotebookdesktop appears.
7 Click Get drivers and click View All Drivers.
System setup 65
The Drivers and Downloads page opens.
8 On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS.
9 Identify the latest BIOS le and click Download File.
You can also analyze which drivers need an update. To do this for your product, click Analyze System for Updates and follow the
instructions on the screen.
10 Select your preferred download method in the Please select your download method below window, click Download File.
The File Download window appears.
11 Click Save to save the le on your tabletnotebookdesktop.
12 Click Run to install the updated BIOS settings on your tabletnotebookdesktop.
Follow the instructions on the screen.
NOTE: It is recommended not to update the BIOS version for more than 3 revisions. For example: If you want to update the BIOS
from 1.0 to 7.0, then install version 4.0 rst and then install version 7.0.
System and setup password
You can create a system password and a setup password to secure your computer.
Password type Description
System password Password that you must enter to log on to your system.
Setup password Password that you must enter to access and make changes to the BIOS settings of your computer.
CAUTION: The password features provide a basic level of security for the data on your computer.
CAUTION: Anyone can access the data stored on your computer if it is not locked and left unattended.
NOTE: Your computer is shipped with the system and setup password feature is disabled.
Assigning a system password and setup password
You can assign a new System Password only when the status is in Not Set.
To enter the system setup, press F2 immediately after a power-on or re-boot.
1 In the System BIOS or System Setup screen, select Security and press Enter.
The Security screen is displayed.
2 Select System Password and create a password in the Enter the new password eld.
Use the following guidelines to assign the system password:
• A password can have up to 32 characters.
• The password can contain the numbers 0 through 9.
• Only lower case letters are valid, upper case letters are not allowed.
• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).
3 Type the system password that you entered earlier in the Conrm new password eld and click OK.
4 Press Esc and a message prompts you to save the changes.
5 Press Y to save the changes.
The computer reboots.
66 System setup
Deleting or changing an existing system and/or setup
password
Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing System and/or
Setup password. You cannot delete or change an existing System or Setup password, if the Password Status is Locked.
To enter the System Setup, press F2 immediately after a power-on or reboot.
1 In the System BIOS or System Setup screen, select System Security and press Enter.
The System Security screen is displayed.
2 In the System Security screen, verify that Password Status is Unlocked.
3 Select System Password, alter or delete the existing system password and press Enter or Tab.
4 Select Setup Password, alter or delete the existing setup password and press Enter or Tab.
NOTE: If you change the System and/or Setup password, re-enter the new password when promoted. If you delete the
System and/or Setup password, conrm the deletion when promoted.
5 Press Esc and a message prompts you to save the changes.
6 Press Y to save the changes and exit from System Setup.
The computer reboots.
System setup 67
Troubleshooting
Enhanced Pre-boot System Assessment (ePSA)
The ePSA is a diagnostic utility available on the tablet. This utility includes a series of tests for a tablet's hardware. Customers can run these
tests even if the computer lacks any media (hard drive, CD drive, etc.). If an ePSA-tested component fails, the system displays an error
code and generates a beep code.
Features:
• Graphical User Interface.
• Automatic Default Operation- runs test on all devices, allowing a user to interrupt and select any device.
• Checks the Master Boot Record for readiness to boot into a full OS environment.
• Tablet panel test.
• Video card.
• Battery test.
• Charger test.
• Primary battery.
• Multiprocessor cache test.
Running the ePSA Diagnostic Utility
NOTE: The following steps can be used to run the ePSA diagnostic utility in DOS mode without using an external keyboard.
1 Power on the system.
2 Before the Dell Logo is displayed, immediately press the Volume Up button to get the Boot Menu.
3 Scroll down the Diagnostics and then press the Volume Down button to select.
4 The tablet will begin running the ePSA utility.
Dell wireless charging mat
• Ensure that the correct AC adapter is plugged into the charging mat and AC input is connected and supplied to the adapter.
• Ensure that the charging mat is not placed directly on metal table or if using a metal table ensure there is at least a 5-cm gap between
the metal table and the charging mat.
• Place a known working wireless charging keyboard on the charging mat and check to see if the LED lights up. The keyboard must be
placed within the charging area and no object should be inserted between the keyboard/Mat and/or Mat/table.
• Or if using a tablet connected to the wireless charging keyboard, then check that the battery indicator displays charging.
• If all the above troubleshooting steps fail, then the charging mat may have malfunctioned. Please contact Dell Support for assistance.
6
68 Troubleshooting
Tablet LED
This section details the diagnostic features of the battery LED in a tablet.
Diagnostic LED
Tablets rely on the Battery LED light blinking amber/white pattern to determine failures listed in the following table:
NOTE:
• The blinking patterns will consist of 2 sets of numbers being represented by (First Group: Amber blinks, Second Group: White
blinks)
• First Group: The LED blinks 1 to 9 times followed by a brief pause with LED o at the interval of 1.5 seconds. (This is in Amber
color)
• Second Group: The LED blinks 1 to 9 times, followed by a longer pause before the next cycle starts again at the interval of 1.5
seconds. (This is in White color)
•Example: No Memory detected (2,3), Battery LED blinks two times of amber color followed by a pause, and then blinks three times
of white color. The Battery LED will pause for 3 seconds before the next cycle repeat itself again
The following table depicts the amber and white blinking patterns with possible troubleshooting resolution:
Table 1. LED pattern
Blinking pattern Problem Description Suggested Resolution
2,1 processor processor failure
2,2 system board, BIOS ROM system board, covers BIOS corruption or ROM error
2,3 memory no memory/no RAM detected
2,4 memory memory failure/RAM failure
2,5 memory invalid memory installed
2,6 system board; chipset system board/ chipset error
2,7 display display failure
3,1 RTC power failure coin-cell battery failure
3,2 PCI/Video PCI/Video card/chip failure
3,3 BIOS recovery 1 recovery image not found
3,4 BIOS recovery 2 recovery image found but invalid
Real Time Clock (RTC) reset
The Real Time Clock (RTC) reset function allows you or the service technician to recover the recently launched model Dell Latitude and
Precision systems from select No POST/No Boot/No Power situations. You can initiate the RTC reset on the system from a power o
state only if it is connected to AC power. Press and hold the power button for 25 seconds. The system RTC reset occurs after you release
the power button.
NOTE: If AC power is disconnected from the system during the process or the power button is held longer than 40 seconds, the
RTC reset process is aborted.
The RTC reset will reset the BIOS to Defaults, un-provision Intel vPro and reset the system date and time. The following items are
unaected by the RTC reset:
Troubleshooting 69
• Service Tag
• Asset Tag
• Ownership Tag
• Admin Password
• System Password
• HDD Password
• Key Databases
• System Logs
The following items may or may not reset based on your custom BIOS setting selections:
• The Boot List
• Enable Legacy OROMs
• Secure Boot Enable
• Allow BIOS Downgrade
Identifying the AC adapter shipped with your
notebooktablet
AC adapters are shipped based on customer requirements or based on regions. To identify the AC adapter shipped with your
tabletnotebook, you can verify it from the service tag.
1 Go to Dell.com/support
2 Type the service tag of your tabletnotebook.
3 Click System conguration. System conguration details are displayed.
4 Click Original conguration to view the AC adapter shipped with your tabletnotebook.
70 Troubleshooting
Contacting Dell
NOTE: If you do not have an active Internet connection, you can nd contact information on your purchase invoice, packing slip,
bill, or Dell product catalog.
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services
may not be available in your area. To contact Dell for sales, technical support, or customer service issues:
1 Go to Dell.com/support.
2 Select your support category.
3 Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.
4 Select the appropriate service or support link based on your need.
7
Contacting Dell 71