Table of Contents
- Dell Latitude 7400 2-in-1 Service Manual
- Working on your computer
- Technology and components
- Removing and installing components
- Troubleshooting
- Getting help
DELL 7400 User Manual
Displayed below is the user manual for 7400 by DELL which is a product in the Notebooks category. This manual has pages.
Related Manuals
Dell Latitude 7400 2-in-1
Service Manual
Regulatory Model: P110G
Regulatory Type: P110G001
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2019 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks
may be trademarks of their respective owners.
2019 - 03
Rev. A00
Contents
1 Working on your computer............................................................................................................................. 5
Safety instructions............................................................................................................................................................. 5
Turning o your computer — Windows 10.....................................................................................................................5
Before working inside your computer..............................................................................................................................6
After working inside your computer.................................................................................................................................6
2 Technology and components..........................................................................................................................7
USB features.......................................................................................................................................................................7
USB 3.0/USB 3.1 Gen 1 (SuperSpeed USB)............................................................................................................. 7
Speed.............................................................................................................................................................................8
Applications...................................................................................................................................................................8
Compatibility................................................................................................................................................................. 9
USB Type-C........................................................................................................................................................................ 9
Alternate Mode.............................................................................................................................................................9
USB Power Delivery.....................................................................................................................................................9
USB Type-C and USB 3.1............................................................................................................................................ 9
Thunderbolt over USB Type-C..................................................................................................................................10
Thunderbolt 3 over USB Type-C.............................................................................................................................. 10
Key Features of Thunderbolt 3 over USB Type-C .................................................................................................10
Thunderbolt Icons........................................................................................................................................................11
HDMI 1.4a........................................................................................................................................................................... 11
HDMI 1.4a Features..................................................................................................................................................... 11
Advantages of HDMI...................................................................................................................................................11
Corning Gorilla Glass......................................................................................................................................................... 11
Benets........................................................................................................................................................................12
3 Removing and installing components............................................................................................................15
Recommended tools........................................................................................................................................................ 15
Screw List..........................................................................................................................................................................15
SD memory card............................................................................................................................................................... 16
Removing the SD memory card................................................................................................................................16
Installing the SD memory card.................................................................................................................................. 16
SIM card tray.....................................................................................................................................................................17
Removing the SIM card tray......................................................................................................................................17
Installing the SIM card tray........................................................................................................................................18
Base cover.........................................................................................................................................................................19
Removing the base cover..........................................................................................................................................19
Installing the base cover............................................................................................................................................22
Battery cable.................................................................................................................................................................... 25
Disconnecting the battery cable.............................................................................................................................. 25
Connecting the battery cable...................................................................................................................................26
Coin cell battery................................................................................................................................................................27
Removing the coin cell battery.................................................................................................................................27
Contents 3
Installing the coin-cell battery...................................................................................................................................28
Solid state drive................................................................................................................................................................29
Removing the solid state drive.................................................................................................................................29
Installing the solid state drive................................................................................................................................... 32
WLAN card....................................................................................................................................................................... 35
Removing the WLAN card........................................................................................................................................35
Installing the WLAN card.......................................................................................................................................... 36
WWAN card...................................................................................................................................................................... 37
Removing the WWAN card.......................................................................................................................................37
Installing the WWAN card.........................................................................................................................................39
Fan......................................................................................................................................................................................41
Removing the fan....................................................................................................................................................... 41
Installing the fan......................................................................................................................................................... 46
Speakers............................................................................................................................................................................ 51
Removing the speakers..............................................................................................................................................51
Installing the speakers............................................................................................................................................... 53
Heatsink............................................................................................................................................................................ 55
Removing the heatsink..............................................................................................................................................55
Installing the heatsink................................................................................................................................................ 59
Display assembly.............................................................................................................................................................. 63
Removing the display assembly............................................................................................................................... 63
Installing the display assembly..................................................................................................................................66
Battery...............................................................................................................................................................................69
Lithium-ion battery precautions............................................................................................................................... 69
Removing the battery................................................................................................................................................70
Installing the battery.................................................................................................................................................. 72
System board....................................................................................................................................................................75
Removing the system board..................................................................................................................................... 75
Installing the system board....................................................................................................................................... 80
Keyboard........................................................................................................................................................................... 86
Removing the keyboard............................................................................................................................................ 86
Installing the keyboard...............................................................................................................................................90
Palmrest assembly........................................................................................................................................................... 95
4 Troubleshooting........................................................................................................................................... 98
Enhanced Pre-Boot System Assessment (ePSA) diagnostics...................................................................................98
Running the ePSA diagnostics.................................................................................................................................98
System diagnostic lights................................................................................................................................................. 98
Flashing BIOS (USB key)................................................................................................................................................ 99
Flashing the BIOS...........................................................................................................................................................100
Backup media and recovery options............................................................................................................................100
WiFi power cycle............................................................................................................................................................ 100
Flea power release..........................................................................................................................................................100
5 Getting help................................................................................................................................................101
Contacting Dell................................................................................................................................................................ 101
4Contents
Working on your computer
Safety instructions
Prerequisite
Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise
noted, each procedure included in this document assumes that the following conditions exist:
• You have read the safety information that shipped with your computer.
• A component can be replaced or, if purchased separately, installed by performing the removal procedure in reverse order.
About this task
WARNING: Disconnect all power sources before opening the computer cover or panels. After you nish working inside the
computer, replace all covers, panels, and screws before connecting to the power source.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional
safety best practices information, see the Regulatory Compliance Homepage
CAUTION: Many repairs may only be done by a certied service technician. You should only perform troubleshooting and simple
repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an
unpainted metal surface at the same time as touching a connector on the back of the computer.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its
edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have
connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the
cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a
cable, ensure that both connectors are correctly oriented and aligned.
NOTE: The color of your computer and certain components may appear dierently than shown in this document.
Turning o your computer — Windows 10
About this task
CAUTION: To avoid losing data, save and close all open les and exit all open programs before you turn o your computer or
remove the side cover.
Steps
1 Click or tap .
2 Click or tap and then click or tap Shut down.
NOTE: Ensure that the computer and all attached devices are turned o. If your computer and attached devices did not
automatically turn o when you shut down your operating system, press and hold the power button for about 6 seconds
to turn them o.
1
Working on your computer 5
Before working inside your computer
About this task
To avoid damaging your computer, perform the following steps before you begin working inside the computer.
Steps
1 Ensure that you follow the Safety Instruction.
2 Ensure that your work surface is at and clean to prevent the computer cover from being scratched.
3 Turn o your computer.
4 Disconnect all network cables from the computer.
CAUTION: To disconnect a network cable, rst unplug the cable from your computer and then unplug the cable from
the network device.
5 Disconnect your computer and all attached devices from their electrical outlets.
6 Press and hold the power button while the computer is unplugged to ground the system board.
NOTE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an
unpainted metal surface at the same time as touching a connector on the back of the computer.
After working inside your computer
About this task
After you complete any replacement procedure, ensure that you connect any external devices, cards, and cables before turning on your
computer.
Steps
1 Connect any telephone or network cables to your computer.
CAUTION: To connect a network cable, rst plug the cable into the network device and then plug it into the
computer.
2 Connect your computer and all attached devices to their electrical outlets.
3 Turn on your computer.
4 If required, verify that the computer works correctly by running ePSA diagnostics.
6Working on your computer
Technology and components
This chapter details the technology and components available in the system.
Topics:
• USB features
• USB Type-C
• HDMI 1.4a
• Corning Gorilla Glass
USB features
Universal Serial Bus, or USB, was introduced in 1996. It dramatically simplied the connection between host computers and peripheral
devices like mice, keyboards, external drivers, and printers.
Let's take a quick look on the USB evolution referencing to the table below.
Table 1. USB evolution
Type Data Transfer Rate Category Introduction Year
USB 2.0 480 Mbps High Speed 2000
USB 3.0/USB 3.1 Gen 1 5 Gbps Super Speed 2010
USB 3.1 Gen 2 10 Gbps Super Speed 2013
USB 3.0/USB 3.1 Gen 1 (SuperSpeed USB)
For years, the USB 2.0 has been rmly entrenched as the de facto interface standard in the PC world with about 6 billion devices sold, and
yet the need for more speed grows by ever faster computing hardware and ever greater bandwidth demands. The USB 3.0/USB 3.1 Gen 1
nally has the answer to the consumers' demands with a theoretically 10 times faster than its predecessor. In a nutshell, USB 3.1 Gen 1
features are as follows:
• Higher transfer rates (up to 5 Gbps)
• Increased maximum bus power and increased device current draw to better accommodate power-hungry devices
• New power management features
• Full-duplex data transfers and support for new transfer types
• Backward USB 2.0 compatibility
• New connectors and cable
The topics below cover some of the most commonly asked questions regarding USB 3.0/USB 3.1 Gen 1.
2
Technology and components 7
Speed
Currently, there are 3 speed modes dened by the latest USB 3.0/USB 3.1 Gen 1 specication. They are Super-Speed, Hi-Speed and Full-
Speed. The new SuperSpeed mode has a transfer rate of 4.8Gbps. While the specication retains Hi-Speed, and Full-Speed USB mode,
commonly known as USB 2.0 and 1.1 respectively, the slower modes still operate at 480Mbps and 12Mbps respectively and are kept to
maintain backward compatibility.
USB 3.0/USB 3.1 Gen 1 achieves the much higher performance by the technical changes below:
• An additional physical bus that is added in parallel with the existing USB 2.0 bus (refer to the picture below).
• USB 2.0 previously had four wires (power, ground, and a pair for dierential data); USB 3.0/USB 3.1 Gen 1 adds four more for two pairs
of dierential signals (receive and transmit) for a combined total of eight connections in the connectors and cabling.
• USB 3.0/USB 3.1 Gen 1 utilizes the bidirectional data interface, rather than USB 2.0's half-duplex arrangement. This gives a 10-fold
increase in theoretical bandwidth.
With today's ever increasing demands placed on data transfers with high-denition video content, terabyte storage devices, high megapixel
count digital cameras etc., USB 2.0 may not be fast enough. Furthermore, no USB 2.0 connection could ever come close to the 480Mbps
theoretical maximum throughput, making data transfer at around 320Mbps (40MB/s) — the actual real-world maximum. Similarly, USB
3.0/USB 3.1 Gen 1 connections will never achieve 4.8Gbps. We will likely see a real-world maximum rate of 400MB/s with overheads. At this
speed, USB 3.0/USB 3.1 Gen 1 is a 10x improvement over USB 2.0.
Applications
USB 3.0/USB 3.1 Gen 1 opens up the laneways and provides more headroom for devices to deliver a better overall experience. Where USB
video was barely tolerable previously (both from a maximum resolution, latency, and video compression perspective), it's easy to imagine
that with 5-10 times the bandwidth available, USB video solutions should work that much better. Single-link DVI requires almost 2Gbps
throughput. Where 480Mbps was limiting, 5Gbps is more than promising. With its promised 4.8Gbps speed, the standard will nd its way
into some products that previously weren't USB territory, like external RAID storage systems.
Listed below are some of the available SuperSpeed USB 3.0/USB 3.1 Gen 1 products:
• External Desktop USB 3.0/USB 3.1 Gen 1 Hard Drives
• Portable USB 3.0/USB 3.1 Gen 1 Hard Drives
• USB 3.0/USB 3.1 Gen 1 Drive Docks & Adapters
• USB 3.0/USB 3.1 Gen 1 Flash Drives & Readers
• USB 3.0/USB 3.1 Gen 1 Solid-state Drives
8Technology and components
• USB 3.0/USB 3.1 Gen 1 RAIDs
• Optical Media Drives
• Multimedia Devices
• Networking
• USB 3.0/USB 3.1 Gen 1 Adapter Cards & Hubs
Compatibility
The good news is that USB 3.0/USB 3.1 Gen 1 has been carefully planned from the start to peacefully co-exist with USB 2.0. First of all,
while USB 3.0/USB 3.1 Gen 1 species new physical connections and thus new cables to take advantage of the higher speed capability of
the new protocol, the connector itself remains the same rectangular shape with the four USB 2.0 contacts in the exact same location as
before. Five new connections to carry receive and transmitted data independently are present on USB 3.0/USB 3.1 Gen 1 cables and only
come into contact when connected to a proper SuperSpeed USB connection.
Windows 8/10 will be bringing native support for USB 3.1 Gen 1 controllers. This is in contrast to previous versions of Windows, which
continue to require separate drivers for USB 3.0/USB 3.1 Gen 1 controllers.
Microsoft announced that Windows 7 would have USB 3.1 Gen 1 support, perhaps not on its immediate release, but in a subsequent Service
Pack or update. It is not out of the question to think that following a successful release of USB 3.0/USB 3.1 Gen 1 support in Windows 7,
SuperSpeed support would trickle down to Vista. Microsoft has conrmed this by stating that most of their partners share the opinion that
Vista should also support USB 3.0/USB 3.1 Gen 1.
USB Type-C
USB Type-C is a new, tiny physical connector. The connector itself can support various exciting new USB standards like USB 3.1 and USB
power delivery (USB PD).
Alternate Mode
USB Type-C is a new connector standard that is very small. It is about a third the size of an old USB Type-A plug. This is a single connector
standard that every device should be able to use. USB Type-C ports can support a variety of dierent protocols using “alternate modes,”
which allows you to have adapters that can output HDMI, VGA, DisplayPort, or other types of connections from that single USB port
USB Power Delivery
The USB PD specication is also closely intertwined with USB Type-C. Currently, smartphones, tablets, and other mobile devices often use
a USB connection to charge. A USB 2.0 connection provides up to 2.5 watts of power — that'll charge your phone, but that's about it. A
laptop might require up to 60 watts, for example. The USB Power Delivery specication ups this power delivery to 100 watts. It's bi-
directional, so a device can either send or receive power. And this power can be transferred at the same time the device is transmitting
data across the connection.
This could spell the end of all those proprietary laptop charging cables, with everything charging via a standard USB connection. You could
charge your laptop from one of those portable battery packs you charge your smartphones and other portable devices from today. You
could plug your laptop into an external display connected to a power cable, and that external display would charge your laptop as you used
it as an external display — all via the one little USB Type-C connection. To use this, the device and the cable have to support USB Power
Delivery. Just having a USB Type-C connection doesn't necessarily mean they do.
USB Type-C and USB 3.1
USB 3.1 is a new USB standard. USB 3's theoretical bandwidth is 5 Gbps, while USB 3.1's is 10 Gbps. That's double the bandwidth, as fast
as a rst-generation Thunderbolt connector. USB Type-C isn't the same thing as USB 3.1. USB Type-C is just a connector shape, and the
Technology and components 9
underlying technology could just be USB 2 or USB 3.0. In fact, Nokia's N1 Android tablet uses a USB Type-C connector, but underneath it's
all USB 2.0 — not even USB 3.0. However, these technologies are closely related.
Thunderbolt over USB Type-C
Thunderbolt is a hardware interface that combines data, video, audio, and power in a single connection. Thunderbolt combines PCI Express
(PCIe) and DisplayPort (DP) into one serial signal, and additionally provides DC power, all in one cable. Thunderbolt 1 and Thunderbolt 2 use
the same connector as miniDP (DisplayPort) to connect to peripherals, while Thunderbolt 3 uses a USB Type-C connector.
Figure 1. Thunderbolt 1 and Thunderbolt 3
1 Thunderbolt 1 and Thunderbolt 2 (using a miniDP connector)
2 Thunderbolt 3 (using a USB Type-C connector)
Thunderbolt 3 over USB Type-C
Thunderbolt 3 brings Thunderbolt to USB Type-C at speeds up to 40 Gbps, creating one compact port that does it all - delivering the
fastest, most versatile connection to any dock, display or data device like an external hard drive. Thunderbolt 3 uses a USB Type-C
connector/port to connect to supported peripherals.
1 Thunderbolt 3 uses USB Type-C connector and cables - It is compact and reversible
2 Thunderbolt 3 supports speed up to 40 Gbps
3 DisplayPort 1.2 – compatible with existing DisplayPort monitors, devices and cables
4 USB Power Delivery - Up to 130W on supported computers
Key Features of Thunderbolt 3 over USB Type-C
1 Thunderbolt, USB, DisplayPort and power on USB Type-C on a single cable (features vary between dierent products)
2 USB Type-C connector and cables which are compact and reversible
3 Supports Thunderbolt Networking (*varies between dierent products)
4 Supports up to 4K displays
5 Up to 40 Gbps
NOTE: Data transfer speed may vary between dierent devices.
10 Technology and components
Thunderbolt Icons
Figure 2. Thunderbolt Iconography Variations
HDMI 1.4a
This topic explains the HDMI 1.4a and its features along with the advantages.
HDMI (High-Denition Multimedia Interface) is an industry-supported, uncompressed, all-digital audio/video interface. HDMI provides an
interface between any compatible digital audio/video source, such as a DVD player, or A/V receiver and a compatible digital audio and/or
video monitor, such as a digital TV (DTV). The intended applications for HDMI TVs, and DVD players. The primary advantage is cable
reduction and content protection provisions. HDMI supports standard, enhanced, or high-denition video, plus multichannel digital audio on
a single cable.
HDMI 1.4a Features
•HDMI Ethernet Channel - Adds high-speed networking to an HDMI link, allowing users to take full advantage of their IP-enabled
devices without a separate Ethernet cable
•Audio Return Channel - Allows an HDMI-connected TV with a built-in tuner to send audio data "upstream" to a surround audio system,
eliminating the need for a separate audio cable
•3D - Denes input/output protocols for major 3D video formats, paving the way for true 3D gaming and 3D home theater applications
•Content Type - Real-time signaling of content types between display and source devices, enabling a TV to optimize picture settings
based on content type
•Additional Color Spaces - Adds support for additional color models used in digital photography and computer graphics
•4K Support - Enables video resolutions far beyond 1080p, supporting next-generation displays that will rival the Digital Cinema systems
used in many commercial movie theaters
•HDMI Micro Connector - A new, smaller connector for phones and other portable devices, supporting video resolutions up to 1080p
•Automotive Connection System - New cables and connectors for automotive video systems, designed to meet the unique demands of
the motoring environment while delivering true HD quality
Advantages of HDMI
• Quality HDMI transfers uncompressed digital audio and video for the highest, crispest image quality.
• Low -cost HDMI provides the quality and functionality of a digital interface while also supporting uncompressed video formats in a
simple, cost-eective manner
• Audio HDMI supports multiple audio formats from standard stereo to multichannel surround sound
• HDMI combines video and multichannel audio into a single cable, eliminating the cost, complexity, and confusion of multiple cables
currently used in A/V systems
• HDMI supports communication between the video source (such as a DVD player) and the DTV, enabling new functionality
Corning Gorilla Glass
Corning Gorilla Glass 5: Corning’s latest composition was formulated to address breakage the #1 consumer complaint, according to
Corning’s research. The new glass is just as thin and light as previous versions, but has been formulated to deliver dramatically improved
Technology and components 11
native damage resistance allowing improved in-eld performance. Corning Gorilla Glass 5 has been tested for performance when subjected
to sharp contact damage, such as asphalt and other real-world surfaces.
Benets
• Enhanced retained strength after use.
• High resistance to scratch and sharp contact damage.
• Improved drop performance.
• Superior surface quality.
Applications
• Ideal protective cover for electronic displays in:
– Smartphones
– Laptop and tablet computer screens
– Wearable devices
• Touchscreen devices
• Optical components
• High strength glass articles
Dimensions
Thickness: 0.4 mm
Viscosity
Table 2. Viscosity
Parameters Vectors
Softening Point (107.6 poises) 884˚C
Annealing Point (1013.2 poises) 623˚C
Strain Point (1014.7 poises) 571˚C
Properties
Table 3. Properties
Density 2.43 g/cm
Youngs Modulus 76.7 GPa
Poissons Ratio 0.21
Shear Modulus 31.7 GPa
Vickers Hardness (200 g load)
• Un-strengthened
• Strengthened
489 kgf/mm2
596 kgf/mm2
12 Technology and components
596 kgf/mm2
Fracture Toughness 0.69 MPa m0.5
Coecient of Expansion (0 ˚C - 300 ˚C) 78.8 x 10-7 /°C
Chemical Strengthening
Capability of >850MPa CS, at 50 µm Depth Of Layer(DOL)
Specications subject to change
Optical
Table 4. Optical
Refractive Index (590 nm)
Core glass** 1.50
Compression layer 1.51
Photo-elastic constant 30.3 nm/cm/MPa
** Core index is used for FSM-based measurements since it is unaected by ion-exchange conditions.
Chemical Durability
Durability is measured via weight loss per surface area after immersion in the solvents shown below. Values are highly dependent upon
actual testing conditions. Data reported is for Corning Gorilla Glass 5.
Table 5. Chemical Durability
Reagent Time Temperature (ºC) Weight Loss (mg/cm2)
HCl - 5% 24 hrs 95 5.9
NH4F:HF - 10% 20 min 20 1.0
HF - 10% 20 min 20 25.2
NaOH - 5% 6 hrs 95 2.7
Electrical
Table 6. Electrical
Frequency (MHz) Dielectric Constant Loss Tangent
54 7.08 0.009
163 7.01 0.010
272 7.01 0.011
272 7.00 0.010
490 7.99 0.010
Technology and components 13
Frequency (MHz) Dielectric Constant Loss Tangent
599 7.97 0.011
912 7.01 0.012
1499 6.99 0.012
1977 6.97 0.014
2466 6.96 0.014
2986 6.96 0.014
Terminated coaxial line similar to that outlined in NIST Technical Notes 1520 and 1355-R
Putting Corning Gorilla Glass 5 to the test.
• Greater damage resistance (upto 1.8X) with deep abrasion.
• Faster chemical strengthening with high Compressive Stress and deeper depth of compression
– Shallower check depth with higher abrasions levels
• Enables thickness reduction
14 Technology and components
Removing and installing components
Recommended tools
The procedures in this document require the following tools:
• Phillips #0 screwdriver
• Phillips #1 screwdriver
• Plastic scribe
• T-30 torx screwdriver
NOTE: The #0 screw driver is for screws 0-1 and the #1 screw driver is for screws 2-4.
Screw List
The following table shows the screw list and the images for Dell Latitude 7400 2-in-1, for dierent components and locations.
Table 7. Screw Size List
Component Screw type Quantity Image
Base cover Captive screws
NOTE: Screws are part
of the base cover
10
SSD M2x2 1
WLAN M2x2 1
WWAN M2x2 1
Fan M2x2 1
Speakers M1.6x1.4 4
Heatsink M1.6x2.5 4
Display assembly M2.5x3.5 6
Battery • M1.6x4.5
• M2x3
• 1
• 4 •
•
System board • M2x2
• M2x4
• 2
• 2 •
3
Removing and installing components 15
Component Screw type Quantity Image
• M2x3 • 5
•
•
Keyboard M1.6x1.5 • 1
• 2
• 40
SD memory card
Removing the SD memory card
1 Press the SD memory card to eject it from the SD memory card slot [1].
2 Remove the SD memory card from the computer [2].
Installing the SD memory card
Insert the SD memory card into its slot [1] until it clicks into place [2].
16 Removing and installing components
SIM card tray
Removing the SIM card tray
NOTE: This procedure applies for models that are shipped with WWAN card only.
1 Insert a paperclip or a SIM card removal tool into the pinhole on the SIM card tray [1].
2 Push the pin to disengage the lock and eject the SIM card tray [2].
3 Pull the SIM card tray out of the computer [3].
Removing and installing components 17
Installing the SIM card tray
Install the SIM card tray into its slot on the computer [1] and push to lock it in place [2].
18 Removing and installing components
2 Use a plastic scribe [1] to pry the base cover along the recess points located in the hinge indents (left and right) [1].
3 Pry the base cover along the edges [2] to separate the base cover from the computer [2].
CAUTION: Do not pull on the base cover from the top side immediately after prying it open from the recesses as it can
damage the base cover.
20 Removing and installing components
4 Lift the base cover o the computer.
Removing and installing components 21
Installing the base cover
Steps
1 Align the base cover and place it on the computer.
22 Removing and installing components
2 Press along the edges of the base cover until it clicks into place.
Removing and installing components 23
3 Tighten the 10 captive screws to secure the base cover to the computer.
24 Removing and installing components
Next steps
1 Install the SD memory card.
2 Follow the procedure in after working inside your computer.
Battery cable
Disconnecting the battery cable
Prerequisites
1 Follow the procedure in before working inside your computer.
2 Remove the SD memory card.
3 Remove the base cover.
Step
Disconnect the battery cable from the connector on the system board.
Removing and installing components 25
Connecting the battery cable
Step
Connect the battery cable to the connector on the system board.
26 Removing and installing components
Next steps
1 Install the base cover.
2 Install the SIM card.
3 Install the SD memory card.
4 Follow the procedure in after working inside your computer.
Coin cell battery
Removing the coin cell battery
Prerequisites
1 Follow the procedure in before working inside your computer.
2 Remove the SD memory card.
3 Remove the base cover.
4 Disconnect the battery cable.
Steps
1 Disconnect the coin-cell battery cable from the connector on the system board [1].
2 Peel and lift the coin-cell battery o the computer [2].
Removing and installing components 27
Installing the coin-cell battery
Steps
1 Ax the coin-cell battery to the system [1].
2 Connect the coin-cell battery cable to the connector on the system board [2].
28 Removing and installing components
Next steps
1 Connect the battery cable
2 Install the base cover.
3 Install the SD memory card.
4 Follow the procedure in after working inside your computer.
Solid state drive
Removing the solid state drive
Prerequisites
1 Follow the procedure in before working inside your computer.
2 Remove the SD memory card.
3 Remove the base cover.
4 Disconnect the battery cable.
Steps
1 Peel o the metal foil [1] and the black tape [2] that partially covers the solid state drive (SSD) cover.
Removing and installing components 29
2 Remove the single (M2x2) screw [1] that secures the SSD shield to the system board.
3 Lift to remove the SSD shield from the system board [2].
30 Removing and installing components
4 Slide and remove the SSD module from the connector on the system board.
Removing and installing components 31
Installing the solid state drive
Steps
1 Align and slide the solid state drive (SSD) module into the connector on the system board.
32 Removing and installing components
2 Place the SSD shield on the SSD module [1] and replace the single (M2x2) screw [2] to secure it to the system board.
Removing and installing components 33
3 Ax the black tape [1] and the metal foil [2] to secure the SSD shield in place.
34 Removing and installing components
Next steps
1 Connect the battery cable
2 Install the base cover.
3 Install the SD memory card.
4 Follow the procedure in after working inside your computer.
WLAN card
Removing the WLAN card
Prerequisites
1 Follow the procedure in before working inside your computer.
2 Remove the SD memory card.
3 Remove the base cover.
4 Disconnect the battery cable.
Steps
1 Partially peel o the Mylar sheet that covers the WLAN card [1].
2 Remove the single (M2x2) screw [2] that secures the WLAN card bracket to the WLAN card.
3 Remove the WLAN card bracket from the WLAN card.
4 Disconnect the wireless antennae cables [4] from the connectors on the WLAN card.
5 Slide and remove the WLAN card [5] from the connector on the system board.
Removing and installing components 35
Installing the WLAN card
Steps
1 Slide the WLAN card [1] at an angle into the WLAN card connector on the system board.
2 Connect the WLAN antenna card cables [2] to the connector on the WLAN card.
3 Align the screw hole on the WLAN card bracket with the screw hole on the WLAN card [3].
4 Replace the single (M2x2) [4] screw to secure the WLAN card to the system board.
5 Stick the Mylar sheet on the system board to cover the WLAN card [5].
36 Removing and installing components
Next steps
1 Connect the battery cable
2 Install the base cover.
3 Install the SD memory card.
4 Follow the procedure in after working inside your computer.
WWAN card
Removing the WWAN card
Prerequisites
1 Follow the procedure in before working inside your computer.
2 Remove the SD memory card.
3 Remove the base cover.
4 Disconnect the battery cable.
Steps
1 Remove the metal shield from the WWAN card.
Removing and installing components 37
2 Remove the single (M2x3) screw [1] that secures the WWAN bracket to the WWAN card.
3 Remove the WWAN bracket [2] from the WWAN card.
4 Disconnect the wireless antennae cables [3] from the connectors on the WWAN card.
5 Slide and remove the WWAN card [4] from the connector on the system board.
38 Removing and installing components
Installing the WWAN card
Steps
1 Slide the WWAN card [1] at an angle into the WWAN card connector on the system board.
2 Connect the WWAN antenna cables [2] to the connector on the WWAN card.
3 Align the screw hole on the WWAN card bracket with the screw hole on the WWAN card [3].
4 Replace the single (M2x2) screw [4] to secure the WWAN card to the system board.
Removing and installing components 39
5 Place the metal shield on the WWAN card.
40 Removing and installing components
Next steps
1 Connect the battery cable
2 Install the base cover.
3 Install the SD memory card.
4 Follow the procedure in after working inside your computer.
Fan
Removing the fan
Prerequisites
1 Follow the procedure in before working inside your computer.
2 Remove the SD memory card.
3 Remove the base cover.
4 Disconnect the battery cable.
Steps
1 Peel o the Mylar sheet from the system board.
Removing and installing components 41
2 Disconnect the fan cable [1] from the connector on the system board [1].
3 Partially peel o the metal foil [2] and the black tape [3] on the SSD shield.
42 Removing and installing components
4 Remove the single (M2x2) screw [1] that secures the WWAN P-sensor bracket to the system board.
5 Remove the WWAN P-sensor bracket [2] from the system board.
Removing and installing components 43
6 Partially peel o the padded gasket [1] from the fan case.
7 Remove the single (M2x2) screw [2] that secures the fan to the system board.
44 Removing and installing components
8 CAUTION: There are cushions, partially obstructing the palmrest, on the bottom side of the fan. Technicians should not
lift the fan directly up, as it may damage the fan.
Partially lift the left side of the fan and slide it to the left to remove it from the computer.
Removing and installing components 45
Installing the fan
Steps
1 Slide the fan at an angle into its slot on the system board.
46 Removing and installing components
2 Replace the single (M2x2) screw [1] to secure the fan to the system board.
3 Adhere the padded rubber gasket [2] on the fan case.
Removing and installing components 47
4 Align the screw holes on the WWAN P-sensor bracket [1] with the screw hole on the fan.
5 Replace the single (M2x2) screw [2] to secure the WWAN P-sensor bracket to the fan.
48 Removing and installing components
6 Connect the fan cable [1] to the connector on the system board.
7 Adhere the black tape [2] and the metal foil [3] partially covering the SSD shield.
Removing and installing components 49
8 Adhere the Mylar sheet on the system board.
50 Removing and installing components
Next steps
1 Connect the battery cable
2 Install the base cover.
3 Install the SD memory card.
4 Follow the procedure in after working inside your computer.
Speakers
Removing the speakers
Prerequisites
1 Follow the procedure in before working inside your computer.
2 Remove the SD memory card.
3 Remove the base cover.
4 Disconnect the battery cable.
Steps
1 Disconnect the speaker cable [1] from the connector from the system board and peel o the speaker ex cable [2] from the battery.
Removing and installing components 51
2 Remove the three (M1.6x1.4) screws [1] that secure the speakers to the system board and lift the speakers o the computer [2].
52 Removing and installing components
Installing the speakers
Steps
1 Align the screw holes on the speakers [1] with the screw holes on the chassis
2 Replace the three (M1.6x1.4) screws [2] that secure the speakers to the chassis.
Removing and installing components 53
3 Connect the speaker cable [1] to the connector on the system board and adhere the speaker ex cable [2] on the battery.
54 Removing and installing components
Next steps
1 Connect the battery cable
2 Install the base cover.
3 Install the SD memory card.
4 Follow the procedure in after working inside your computer.
Heatsink
Removing the heatsink
Prerequisites
1 Follow the procedure in before working inside your computer.
2 Remove the SD memory card.
3 Remove the base cover.
4 Disconnect the battery cable.
Steps
1 Partially peel o the Mylar sheet [1] from the system board.
2 Disconnect the camera and touch screen FPC cable [2] from the connector on the system board.
3 Peel o the camera and touch screen FPC cable from the heatsink shield [3].
Removing and installing components 55
4 Remove the metal foil from the heatsink shield.
56 Removing and installing components
5 Remove the heatsink shield from the system board.
Removing and installing components 57
6 Remove the four (M1.6x2.5) screws [1] that secure the heatsink on the system board.
7 Lift the heatsink [2] o the system board.
58 Removing and installing components
Installing the heatsink
Steps
1 Align the screw holes on the heatsink [1] with the screw holes on the system board.
2 Replace the four (M1.6x2.5) screws [2] that secure the heatsink to the system board.
Removing and installing components 59
3 Place the heatsink shield on the heatsink.
60 Removing and installing components
4 Adhere the metal foils on the heatsink shield.
Removing and installing components 61
5 Adhere the camera and touch screen FPC cables on the heatsink shield [1].
6 Connect the camera and touch screen FPC cables [2] to the connector on the system board.
7 Adhere the Mylar sheet [3] on the system board.
62 Removing and installing components
Next steps
1 Connect the battery cable
2 Install the base cover.
3 Install the SD memory card.
4 Follow the procedure in after working inside your computer.
Display assembly
Removing the display assembly
Prerequisites
1 Follow the procedure in before working inside your computer.
2 Remove the SD memory card.
3 Remove the base cover.
4 Disconnect the battery cable.
Steps
1 Partially peel o the Mylar sheet [1] from the system board.
2 Disconnect the camera and touch screen FPC cable [2] from the connector on the system board.
3 Peel o the camera and touch screen FPC cable from the heatsink shield [3].
Removing and installing components 63
4 Peel o the tape on the display cable [1].
5 Pry the retention clips on both sides and ip open the latch [2].
CAUTION: The connector for the display cable features a latch that locks it in place on the system board which
technicians must ip open in order to disconnect the display cable from the system board. After ipping open the latch,
technicians must grasp the left and right sides of the cable's connector head and disconnect the display cable from the
system board in a direct upward motion to prevent damage to the connector's pins.
6 Disconnect the display cable from the connector on the system board [3].
64 Removing and installing components
7 Remove the six (M2.5x3.5) screws [1] that secures the display hinges to the computer.
8 Lift the display assembly o the computer [2].
Removing and installing components 65
Installing the display assembly
Steps
1 Install the display assembly with hinges open at 180º aligned to the computer [1].
2 Replace the six (M2.5x3.5) screws [1] that secures the display hinges to the computer [2].
66 Removing and installing components
3 Connect the display cable [1] to the connector on the system board.
4 Close the latch [2] and adhere the tape on the display cable [3].
Removing and installing components 67
5 Route the camera and touch screen FPC and adhere it on the heatsink shield [1].
6 Connect the camera and touch screen FPC to the connector on the system board [2] and stick the Mylar sheet on the system board
[3].
68 Removing and installing components
Next steps
1 Connect the battery cable
2 Install the base cover.
3 Install the SD memory card.
4 Follow the procedure in after working inside your computer.
Battery
Lithium-ion battery precautions
CAUTION:
• Exercise caution when handling Lithium-ion batteries.
• Discharge the battery as much as possible before removing it from the system. This can be done by disconnecting the AC adapter
from the system to allow the battery to drain.
• Do not crush, drop, mutilate, or penetrate the battery with foreign objects.
• Do not expose the battery to high temperatures, or disassemble battery packs and cells.
• Do not apply pressure to the surface of the battery.
• Do not bend the battery.
• Do not use tools of any kind to pry on or against the battery.
• If a battery gets stuck in a device as a result of swelling, do not try to free it as puncturing, bending, or crushing a Lithium-ion
battery can be dangerous. In such an instance, the entire system should be replaced. Contact https://www.dell.com/support for
assistance and further instructions.
• Always purchase genuine batteries from https://www.dell.com or authorized Dell partners and re-sellers.
Removing and installing components 69
Removing the battery
Prerequisites
1 Follow the procedure in before working inside your computer.
2 Remove the SD memory card.
3 Remove the base cover.
4 Disconnect the battery cable.
5 Remove the speakers.
Steps
1 Peel o the tape [1] and unroute the wireless antennae cables from the routing guides on the battery [2].
NOTE: The cables for the wireless antennas are routed over the plastic bracket at the top left corner and within the
routing channels along the left and bottom side of the battery. As a result, technicians must be careful when unrouting
the antenna cables from their routing guides while they are still attached to the wireless card. If there is diculty in
unrouting the antenna cables from their routing channels, remove the WLAN card from the computer to create space to
unroute the cables.
2 Remove the single (M1.6x4.5) screw [1] and four (M2x3) screws that secure the battery to the chassis.
3 Lift and remove the battery o the computer [2].
70 Removing and installing components
Figure 3. 4-cell battery
NOTE: A 6-cell battery has an extra M2x4 screw shown in green. Remove the screw before removing the battery from
the computer.
Table 8. Battery screw description
Size Amount
4-cell battery Yellow M2x3L 5
Red M1.6x4.5L 1
6-cell battery Green M2x4L 1
Removing and installing components 71
Figure 4. 6-cell battery
Installing the battery
Steps
1 Align the screw holes on the battery with the screw holes on the palmrest assembly [1].
2 Replace the four (M2x3) screws and single (M1.6x4.5) screw that secure the battery to the palmrest assembly [2].
72 Removing and installing components
NOTE: Install the extra M2x4 screw for 6-cell battery. The screw is shown in green, in the battery disassembly section.
3 Stick the tape on wireless antennae cable securing it to the battery [1].
4 Thread the antennae cables along the routing channels and supporting bracket on the battery [2].
Removing and installing components 73
5 Connect the battery cable to the system board.
74 Removing and installing components
Next steps
1 Connect the battery cable
2 Install the base cover.
3 Install the SD memory card.
4 Follow the procedure in after working inside your computer.
System board
Removing the system board
Prerequisites
1 Follow the procedure in before working inside your computer.
2 Remove the SD memory card.
3 Remove the base cover.
4 Disconnect the battery cable.
5 Remove the coin cell.
6 Remove the SSD.
7 Remove the WLAN card.
8 Remove the WWAN card.
9 Remove the fan.
10 Remove the speakers.
11 Remove the heatsink.
Removing and installing components 75
12 Remove the battery.
Steps
1 Disconnect the coin cell cable from the system board [1] and remove the coin cell from the system board [2].
2 Peel o the tape on the display cable connector of the system board [3].
3 Pry the retention clips on both sides of the display cable connector, to ip open the latch [4].
4 CAUTION: The connector for the display cable features an actuator that locks it in place on the system board. Flip open
the latch to disconnect the display cable from the system board. Grasp the left and right sides of the cable's connector
head and disconnect the display cable from the system board in a direct upward motion to prevent damage to the
connector's pins.
Disconnect the display cable from the system board [5].
5 Disconnect the following power button cable from the system board [1].
6 Disconnect the USH board cable [2] and keyboard with backlight cable [3] from the system board.
7 Disconnect the touchpad cable [4] and LED board cable [5] from the system board.
76 Removing and installing components
8 Remove the single (M2x2) screw [1] securing the power ngerprint bracket to system board.
9 Remove the power ngerprint bracket [2] and disconnect the cable from the system board [3].
10 Disconnect the LTE P-sensor and isolator antenna cables [4] from the system board.
11 Disconnect the LTE MAIN and AUX antennae cables [5] from the system board.
Removing and installing components 77
12 Remove the single (M2x2) screw [1] and remove the SSD bracket from the system board [2].
13 Remove the two (M2x4) screws [3] and remove the USB Type-C bracket [4] from the system board.
78 Removing and installing components
14 CAUTION: For models shipped with no LTE support, the dummy SIM card tray must rst be removed from the system
before removing the system board.
Remove the ve (M2x3) screws [1] and remove the system board from the computer [2].
Removing and installing components 79
Installing the system board
Steps
1 Install the system board in the computer [1] and install the ve (M2x3) screws securing it to the computer.
80 Removing and installing components
2 Install the USB Type-C bracket [1] on the system board and secure it using two (M2x4) screws [2] on the system board.
3 Install the SSD bracket [3] and secure it using a single (M2x2) screw [4] to the system board.
Removing and installing components 81
4 Connect the Power button/ngerprint reader cable to the system board [1].
5 Install the power button/nger print reader bracket [2] on the system board and secure it using the single (M2x2) screw [3].
6 Connect the LTE P-sensor and isolator antenna cables [4] on the system board.
7 Connect the LTE MAIN and AUX antennae cables [5] on the system board.
82 Removing and installing components
8 Connect the following power button cable to the system board [1].
9 Connect the USH board cable [2] and keyboard with backlight cable [3] to the system board.
10 Connect the touchpad cable [4] and LED board cable [5] to the system board.
Removing and installing components 83
11 Install the coin cell [1] on the system board and connect its cable to the system board [2].
12 Connect the display cable to the system board [3] and ip close the actuator [4].
13 Secure the display cable connector by sticking the tape on the system board [5].
84 Removing and installing components
Next steps
1 Install the battery.
2 Install the heatsink
3 Install the speaker.
4 Install the fan.
5 Install the WWAN card.
6 Install the WLAN card.
7 Install the SSD.
8 Install the coin cell
9 Connect the battery cable
10 Install the base cover.
11 Install the SIM card
12 Install the SD memory card.
13 Follow the procedure after working inside your computer.
Removing and installing components 85
Keyboard
Removing the keyboard
Prerequisites
1 Follow the procedure in before working inside your computer.
2 Remove the SD memory card.
3 Remove the base cover.
4 Disconnect the battery cable.
5 Remove the coin cell.
6 Remove the SSD.
7 Remove the WLAN card.
8 Remove the WWAN card.
9 Remove the fan.
10 Remove the speakers.
11 Remove the battery.
12 Remove the heatsink.
13 Remove the system board.
Steps
1 Peel o the USH board cable [1], touchpad cable [2], and LED board cable [3] from the keyboard base.
2 Peel back the two pieces of LTE antenna module copper foil [1, 3] and LTE AUX cable from the keyboard [2].
86 Removing and installing components
3 Disconnect the smartcard reader FPC from the USH board [4] and peel o the FPC cable from the keyboard [5].
4 Remove the two (M1.6x1.5) screws [1] to remove the middle battery bracket [2] from the computer.
5 Peel o the keyboard and backlight FPC cables from the keyboard [3].
6 Remove the single (M1.6x1.5) screw [4] to remove the left battery bracket [5] from the computer.
Removing and installing components 87
7 Remove the 40 (M1.6x1.5) screws that secure the keyboard to the palmrest assembly.
88 Removing and installing components
8 Lift the keyboard o the palmrest assembly.
Removing and installing components 89
Installing the keyboard
Steps
1 Place the keyboard on the palmrest assembly.
90 Removing and installing components
2 Replace the 40 (M1.6x1.5) screws on the keyboard to secure it to the palmrest assembly.
Removing and installing components 91
3 Install the middle battery bracket [1] and secure it using two (M1.6x1.5) screws [2].
4 Stick the keyboard and backlight FPC cables to the keyboard [3].
5 Install left battery bracket [4] and secure it using single (M1.6x1.5) screw [5].
92 Removing and installing components
6 Stick the two pieces of LTE antenna module copper foil [1, 3] and LTE AUX cable on the keyboard [2].
7 Route and stick the smart card FPC cable [4] on the keyboard and connect it to the USH board [5].
Removing and installing components 93
8 Stick the USH board cable [1], touchpad cable [2], and LED board cable [3] on the keyboard base.
94 Removing and installing components
Next steps
1 Install the system board
2 Install the battery.
3 Install the heatsink
4 Install the speaker.
5 Install the fan.
6 Install the WWAN card.
7 Install the WLAN card.
8 Install the SSD.
9 Install the coin cell
10 Connect the battery cable
11 Install the base cover.
12 Install the SIM card
13 Install the SD memory card.
14 Follow the procedure after working inside your computer.
Palmrest assembly
Prerequisites
1 Follow the procedure in before working inside your computer.
2 Remove the SD memory card.
3 Remove the base cover.
4 Disconnect the battery cable.
Removing and installing components 95
5 Remove the coin cell.
6 Remove the SSD.
7 Remove the WLAN card.
8 Remove the WWAN card.
9 Remove the fan.
10 Remove the speakers.
11 Remove the heatsink.
12 Remove the display assembly.
13 Remove the battery.
14 Remove the system board.
15 Remove the keyboard.
Steps
1 After performing the preceding steps, you are left with palmrest assembly.
NOTE: Please refer to order details for exact specics of sub-components dened in the palmrest assembly.
2 Transfer the post-requisite components onto the new palmrest assembly.
Next steps
1 Install the keyboard
2 Install the system board
3 Install the battery.
4 Install the display assembly
5 Install the heatsink
6 Install the speaker.
7 Install the fan.
96 Removing and installing components
Troubleshooting
Enhanced Pre-Boot System Assessment (ePSA)
diagnostics
The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware. The ePSA is embedded with the
BIOS and is launched by the BIOS internally. The embedded system diagnostics provides a set of options for particular devices or device
groups allowing you to:
• Run tests automatically or in an interactive mode
• Repeat tests
• Display or save test results
• Run thorough tests to introduce additional test options to provide extra information about the failed device(s)
• View status messages that inform you if tests are completed successfully
• View error messages that inform you of problems encountered during testing
NOTE: Some tests for specic devices require user interaction. Always ensure that you are present at the computer terminal
when the diagnostic tests are performed.
Running the ePSA diagnostics
1 Turn on your computer.
2 As the computer boots, press the F12 key as the Dell logo appears.
3 On the boot menu screen, select the Diagnostics option.
4 Click the arrow at the bottom left corner.
Diagnostics front page is displayed.
5 Click the arrow in the lower-right corner to go to the page listing.
The items detected are listed.
6 To run a diagnostic test on a specic device, press Esc and click Yes to stop the diagnostic test.
7 Select the device from the left pane and click Run Tests.
8 If there are any issues, error codes are displayed.
Note the error code and validation number and contact Dell.
System diagnostic lights
Battery-status light
Indicates the power and battery-charge status.
Solid white — Power adapter is connected and the battery has more than 5 percent charge.
Amber — Computer is running on battery and the battery has less than 5 percent charge.
O
• Power adapter is connected and the battery is fully charged.
4
98 Troubleshooting
• Computer is running on battery and the battery has more than 5 percent charge.
• Computer is in sleep state, hibernation, or turned o.
The power and battery-status light blinks amber along with beep codes indicating failures.
For example, the power and battery-status light blinks amber two times followed by a pause, and then blinks white three times followed by
a pause. This 2,3 pattern continues until the computer is turned o indicating no memory or RAM is detected.
The following table shows dierent power and battery-status light patterns and associated problems.
Table 9. LED codes
Diagnostic light codes Problem description
2,1 Processor failure
2,2 System board: BIOS or ROM (Read-Only Memory) failure
2,3 No memory or RAM (Random-Access Memory) detected
2,4 Memory or RAM (Random-Access Memory) failure
2,5 Invalid memory installed
2,6 System-board or chipset error
2,7 Display failure
3,1 Coin-cell battery failure
3,2 PCI, video card/chip failure
3,3 Recovery image not found
3,4 Recovery image found but invalid
3,5 Power-rail failure
3,6 System BIOS Flash incomplete
3,7 Management Engine (ME) error
Camera status light: Indicates whether the camera is in use.
• Solid white — Camera is in use.
•O — Camera is not in use.
Caps Lock status light: Indicates whether Caps Lock is enabled or disabled.
• Solid white — Caps Lock enabled.
•O — Caps Lock disabled.
Flashing BIOS (USB key)
1 Follow the procedure from step 1 to step 7 in "Flashing the BIOS" to download the latest BIOS setup program le.
2 Create a bootable USB drive. For more information see the knowledge base article SLN143196 at www.dell.com/support.
3 Copy the BIOS setup program le to the bootable USB drive.
4 Connect the bootable USB drive to the computer that needs the BIOS update.
5 Restart the computer and press F12 when the Dell logo is displayed on the screen.
6 Boot to the USB drive from the One Time Boot Menu.
7 Type the BIOS setup program lename and press Enter.
8 The BIOS Update Utility appears. Follow the instructions on the screen to complete the BIOS update.
Troubleshooting 99
Flashing the BIOS
About this task
You may need to ash (update) the BIOS when an update is available or when you replace the system board.
Follow these steps to ash the BIOS:
Steps
1 Turn on your computer.
2 Go to www.dell.com/support.
3 Click Product support, enter the Service Tag of your computer, and then click Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.
4 Click Drivers & downloads > Find it myself.
5 Select the operating system installed on your computer.
6 Scroll down the page and expand BIOS.
7 Click Download to download the latest version of the BIOS for your computer.
8 After the download is complete, navigate to the folder where you saved the BIOS update le.
9 Double-click the BIOS update le icon and follow the instructions on the screen.
Backup media and recovery options
Dell proposes multiple options for recovering Windows operating system on your Dell PC. For more information. see Dell Windows Backup
Media and Recovery Options.
WiFi power cycle
About this task
If your computer is unable to access the internet due to WiFi connectivity issues a WiFi power cycle procedure may be performed. The
following procedure provides the instructions on how to conduct a WiFi power cycle:
NOTE: Some ISPs (Internet Service Providers) provide a modem/router combo device.
Steps
1 Turn o your computer.
2 Turn o the modem.
3 Turn o the wireless router.
4 Wait for 30 seconds.
5 Turn on the wireless router.
6 Turn on the modem.
7 Turn on your computer.
Flea power release
About this task
Flea power is the residual static electricity that remains on the computer even after it has been powered o and the battery has been
removed. The following procedure provides the instructions on how to conduct ea power release:
Steps
1 Turn o your computer.
2 Disconnect the power adapter from your computer.
3 Press and hold the power button for 15 seconds to drain the ea power.
4 Connect the power adapter to your computer.
5 Turn on your computer.
100 Troubleshooting
Getting help
Contacting Dell
Prerequisite
NOTE: If you do not have an active Internet connection, you can nd contact information on your purchase invoice, packing slip,
bill, or Dell product catalog.
About this task
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services
may not be available in your area. To contact Dell for sales, technical support, or customer service issues:
Steps
1 Go to Dell.com/support.
2 Select your support category.
3 Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.
4 Select the appropriate service or support link based on your need.
5
Getting help 101