DELL 7530 User Manual

Displayed below is the user manual for 7530 by DELL which is a product in the Notebooks category. This manual has pages.

Related Manuals

DELL 7530 Manual

Dell Precision 7530

Service Manual

Regulatory Model: P74F

Regulatory Type: P74F001

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

may be trademarks of their respective owners.

2018 - 06

Rev. A00

Contents

1 Working on your computer............................................................................................................................. 6

Safety instructions.............................................................................................................................................................6

Turning o your computer — Windows 10.....................................................................................................................6

Before working inside your computer..............................................................................................................................6

After working inside your computer.................................................................................................................................7

2 Technology and components..........................................................................................................................8

HDMI 2.0............................................................................................................................................................................. 8

HDMI 2.0 Features.......................................................................................................................................................8

Advantages of HDMI................................................................................................................................................... 8

USB features...................................................................................................................................................................... 9

USB 3.0/USB 3.1 Gen 1 (SuperSpeed USB).............................................................................................................9

Speed.............................................................................................................................................................................9

Applications................................................................................................................................................................. 10

Compatibility................................................................................................................................................................10

USB Type-C........................................................................................................................................................................11

Alternate Mode............................................................................................................................................................11

USB Power Delivery....................................................................................................................................................11

USB Type-C and USB 3.1............................................................................................................................................11

Thunderbolt over Type-C........................................................................................................................................... 11

Thunderbolt 3 over Type-C....................................................................................................................................... 12

Key Features of Thunderbolt 3 over USB Type-C .................................................................................................12

Thunderbolt Icons.......................................................................................................................................................12

3 Removing and installing components............................................................................................................13

Recommended tools.........................................................................................................................................................13

Screw size list....................................................................................................................................................................13

SD card.............................................................................................................................................................................. 14

Removing SD card...................................................................................................................................................... 14

Installing SD card........................................................................................................................................................ 15

Base cover.........................................................................................................................................................................16

Removing the base cover..........................................................................................................................................16

Installing the base cover.............................................................................................................................................17

Battery............................................................................................................................................................................... 18

Lithium-ion battery precautions................................................................................................................................ 18

Removing the battery................................................................................................................................................ 19

Installing the battery..................................................................................................................................................20

Hard drive..........................................................................................................................................................................22

Removing the hard drive assembly..........................................................................................................................22

Installing the hard drive assembly............................................................................................................................ 23

Hard drive interposer board............................................................................................................................................ 24

Removing the hard drive interposer board............................................................................................................. 24

Installing the hard drive interposer board................................................................................................................25

Contents 3

Keyboard lattice and Keyboard.......................................................................................................................................26

Removing the keyboard............................................................................................................................................ 26

Installing the keyboard...............................................................................................................................................30

Memory modules............................................................................................................................................................. 32

Removing the primary memory module.................................................................................................................. 32

Installing the primary memory module.....................................................................................................................33

Removing the secondary memory module............................................................................................................. 34

Installing the secondary memory module................................................................................................................35

WWAN card......................................................................................................................................................................36

Removing WWAN card............................................................................................................................................. 36

Installing the WWAN card......................................................................................................................................... 37

WLAN card....................................................................................................................................................................... 38

Removing the WLAN card........................................................................................................................................38

Installing the WLAN card.......................................................................................................................................... 39

Solid State Drive — optional .........................................................................................................................................40

Removing the M.2 Solid State Drive—SSD module............................................................................................. 40

Installing the M.2 SSD module................................................................................................................................. 43

Coin-cell battery...............................................................................................................................................................45

Removing the coin cell battery.................................................................................................................................45

Installing the coin cell battery...................................................................................................................................46

Power connector port..................................................................................................................................................... 47

Removing the power connector port...................................................................................................................... 47

Installing the power connector port........................................................................................................................ 49

Palm rest............................................................................................................................................................................ 51

Removing the palmrest.............................................................................................................................................. 51

Installing the palmrest................................................................................................................................................54

Touchpad button..............................................................................................................................................................56

Removing the Touchpad buttons.............................................................................................................................56

Installing the Touchpad button................................................................................................................................. 57

SIM card............................................................................................................................................................................58

Removing SIM card................................................................................................................................................... 58

Installing SIM card......................................................................................................................................................59

Smart card cage...............................................................................................................................................................60

Removing the smart card cage................................................................................................................................60

Installing the smart card cage................................................................................................................................... 61

Speaker............................................................................................................................................................................. 62

Removing the speakers ............................................................................................................................................62

Installing the speakers............................................................................................................................................... 63

LED board......................................................................................................................................................................... 64

Removing the LED board..........................................................................................................................................64

Installing the LED board............................................................................................................................................ 65

Heat sink assembly.......................................................................................................................................................... 66

Removing the heat sink assembly........................................................................................................................... 66

Installing the heat sink assembly..............................................................................................................................69

Graphics card.................................................................................................................................................................... 71

Removing the graphics card......................................................................................................................................71

Installing the graphics card....................................................................................................................................... 72

4Contents

System board....................................................................................................................................................................73

Removing the system board..................................................................................................................................... 73

Installing the system board....................................................................................................................................... 76

Display assembly.............................................................................................................................................................. 79

Removing the display assembly................................................................................................................................79

Installing the display assembly..................................................................................................................................82

Display bezel..................................................................................................................................................................... 85

Removing the display bezel...................................................................................................................................... 85

Installing the display bezel.........................................................................................................................................86

Display hinges................................................................................................................................................................... 87

Removing the display hinge...................................................................................................................................... 87

Installing the display hinge........................................................................................................................................ 88

Display panel.....................................................................................................................................................................89

Removing the display panel...................................................................................................................................... 89

Installing the display panel......................................................................................................................................... 91

Camera.............................................................................................................................................................................. 93

Removing the camera............................................................................................................................................... 93

Installing the camera..................................................................................................................................................94

eDP cable..........................................................................................................................................................................95

Removing the eDP cable.......................................................................................................................................... 95

Installing the eDP cable.............................................................................................................................................96

Display bracket................................................................................................................................................................. 97

Removing the display support bracket.................................................................................................................... 97

Installing the display support bracket...................................................................................................................... 98

4 Troubleshooting..........................................................................................................................................100

Enhanced Pre-Boot System Assessment — ePSA diagnostics.............................................................................. 100

Running the ePSA Diagnostics...............................................................................................................................100

Diagnostic LED................................................................................................................................................................ 101

Battery status LED..........................................................................................................................................................101

5 Getting help............................................................................................................................................... 103

Contacting Dell............................................................................................................................................................... 103

Contents 5

Working on your computer

Safety instructions

Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise

noted, each procedure included in this document assumes that the following conditions exist:

• You have read the safety information that shipped with your computer.

• A component can be replaced or, if purchased separately, installed by performing the removal procedure in reverse order.

WARNING: Disconnect all power sources before opening the computer cover or panels. After you nish working inside the

computer, replace all covers, panels, and screws before connecting to the power source.

WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional

safety best practices information, see the Regulatory Compliance Homepage

CAUTION: Many repairs may only be done by a certied service technician. You should only perform troubleshooting and simple

repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.

Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an

unpainted metal surface at the same time as touching a connector on the back of the computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its

edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have

connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the

cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a

cable, ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear dierently than shown in this document.

Turning o your computer — Windows 10

CAUTION: To avoid losing data, save and close all open les and exit all open programs before you turn o your computer or

remove the side cover.

1 Click or tap .

2 Click or tap and then click or tap Shut down.

NOTE: Ensure that the computer and all attached devices are turned o. If your computer and attached devices did not

automatically turn o when you shut down your operating system, press and hold the power button for about 6 seconds to

turn them o.

Before working inside your computer

1 Ensure that your work surface is at and clean to prevent the computer cover from being scratched.

2 Turn o your computer.

3 If the computer is connected to a docking device (docked), undock it.

4 Disconnect all network cables from the computer (if available).

6 Working on your computer

CAUTION: If your computer has an RJ45 port, disconnect the network cable by rst unplugging the cable from your

computer.

5 Disconnect your computer and all attached devices from their electrical outlets.

6 Open the display.

7 Press and hold the power button for few seconds, to ground the system board.

CAUTION: To guard against electrical shock unplug your computer from the electrical outlet before performing Step # 8.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an

unpainted metal surface at the same time as touching a connector on the back of the computer.

8 Remove any installed ExpressCards or Smart Cards from the appropriate slots.

After working inside your computer

After you complete any replacement procedure, ensure that you connect external devices, cards, and cables before turning on your

computer.

CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries

designed for other Dell computers.

1 Connect any external devices, such as a port replicator or media base, and replace any cards, such as an ExpressCard.

2 Connect any telephone or network cables to your computer.

CAUTION: To connect a network cable, rst plug the cable into the network device and then plug it into the

computer.

3 Connect your computer and all attached devices to their electrical outlets.

4 Turn on your computer.

Working on your computer 7

Technology and components

This chapter details the technology and components available in the system.

Topics:

• HDMI 2.0

• USB features

• USB Type-C

HDMI 2.0

This topic explains the HDMI 2.0 and its features along with the advantages.

HDMI (High-Denition Multimedia Interface) is an industry-supported, uncompressed, all-digital audio/video interface. HDMI provides an

interface between any compatible digital audio/video source, such as a DVD player, or A/V receiver and a compatible digital audio and/or

video monitor, such as a digital TV (DTV). The intended applications for HDMI TVs, and DVD players. The primary advantage is cable

reduction and content protection provisions. HDMI supports standard, enhanced, or high-denition video, plus multichannel digital audio on

a single cable.

HDMI 2.0 Features

•HDMI Ethernet Channel - Adds high-speed networking to an HDMI link, allowing users to take full advantage of their IP-enabled

devices without a separate Ethernet cable

•Audio Return Channel - Allows an HDMI-connected TV with a built-in tuner to send audio data "upstream" to a surround audio system,

eliminating the need for a separate audio cable

•3D - Denes input/output protocols for major 3D video formats, paving the way for true 3D gaming and 3D home theater applications

•Content Type - Real-time signaling of content types between display and source devices, enabling a TV to optimize picture settings

based on content type

•Additional Color Spaces - Adds support for additional color models used in digital photography and computer graphics

•4K Support - Enables video resolutions far beyond 1080p, supporting next-generation displays that will rival the Digital Cinema systems

used in many commercial movie theaters

•HDMI Micro Connector - A new, smaller connector for phones and other portable devices, supporting video resolutions up to 1080p

•Automotive Connection System - New cables and connectors for automotive video systems, designed to meet the unique demands of

the motoring environment while delivering true HD quality

Advantages of HDMI

• Quality HDMI transfers uncompressed digital audio and video for the highest, crispest image quality.

• Low -cost HDMI provides the quality and functionality of a digital interface while also supporting uncompressed video formats in a

simple, cost-eective manner

• Audio HDMI supports multiple audio formats from standard stereo to multichannel surround sound

• HDMI combines video and multichannel audio into a single cable, eliminating the cost, complexity, and confusion of multiple cables

currently used in A/V systems

• HDMI supports communication between the video source (such as a DVD player) and the DTV, enabling new functionality

8 Technology and components

USB features

Universal Serial Bus, or USB, was introduced in 1996. It dramatically simplied the connection between host computers and peripheral

devices like mice, keyboards, external drivers, and printers.

Let's take a quick look on the USB evolution referencing to the table below.

Table 1. USB evolution

Type Data Transfer Rate Category Introduction Year

USB 2.0 480 Mbps High Speed 2000

USB 3.0/USB 3.1 Gen 1 5 Gbps Super Speed 2010

USB 3.1 Gen 2 10 Gbps Super Speed 2013

USB 3.0/USB 3.1 Gen 1 (SuperSpeed USB)

For years, the USB 2.0 has been rmly entrenched as the de facto interface standard in the PC world with about 6 billion devices sold, and

yet the need for more speed grows by ever faster computing hardware and ever greater bandwidth demands. The USB 3.0/USB 3.1 Gen 1

nally has the answer to the consumers' demands with a theoretically 10 times faster than its predecessor. In a nutshell, USB 3.1 Gen 1

features are as follows:

• Higher transfer rates (up to 5 Gbps)

• Increased maximum bus power and increased device current draw to better accommodate power-hungry devices

• New power management features

• Full-duplex data transfers and support for new transfer types

• Backward USB 2.0 compatibility

• New connectors and cable

The topics below cover some of the most commonly asked questions regarding USB 3.0/USB 3.1 Gen 1.

Speed

Currently, there are 3 speed modes dened by the latest USB 3.0/USB 3.1 Gen 1 specication. They are Super-Speed, Hi-Speed and Full-

Speed. The new SuperSpeed mode has a transfer rate of 4.8Gbps. While the specication retains Hi-Speed, and Full-Speed USB mode,

commonly known as USB 2.0 and 1.1 respectively, the slower modes still operate at 480Mbps and 12Mbps respectively and are kept to

maintain backward compatibility.

USB 3.0/USB 3.1 Gen 1 achieves the much higher performance by the technical changes below:

• An additional physical bus that is added in parallel with the existing USB 2.0 bus (refer to the picture below).

• USB 2.0 previously had four wires (power, ground, and a pair for dierential data); USB 3.0/USB 3.1 Gen 1 adds four more for two pairs

of dierential signals (receive and transmit) for a combined total of eight connections in the connectors and cabling.

• USB 3.0/USB 3.1 Gen 1 utilizes the bidirectional data interface, rather than USB 2.0's half-duplex arrangement. This gives a 10-fold

increase in theoretical bandwidth.

Technology and components 9

With today's ever increasing demands placed on data transfers with high-denition video content, terabyte storage devices, high megapixel

count digital cameras etc., USB 2.0 may not be fast enough. Furthermore, no USB 2.0 connection could ever come close to the 480Mbps

theoretical maximum throughput, making data transfer at around 320Mbps (40MB/s) — the actual real-world maximum. Similarly, USB

3.0/USB 3.1 Gen 1 connections will never achieve 4.8Gbps. We will likely see a real-world maximum rate of 400MB/s with overheads. At this

speed, USB 3.0/USB 3.1 Gen 1 is a 10x improvement over USB 2.0.

Applications

USB 3.0/USB 3.1 Gen 1 opens up the laneways and provides more headroom for devices to deliver a better overall experience. Where USB

video was barely tolerable previously (both from a maximum resolution, latency, and video compression perspective), it's easy to imagine

that with 5-10 times the bandwidth available, USB video solutions should work that much better. Single-link DVI requires almost 2Gbps

throughput. Where 480Mbps was limiting, 5Gbps is more than promising. With its promised 4.8Gbps speed, the standard will nd its way

into some products that previously weren't USB territory, like external RAID storage systems.

Listed below are some of the available SuperSpeed USB 3.0/USB 3.1 Gen 1 products:

• External Desktop USB 3.0/USB 3.1 Gen 1 Hard Drives

• Portable USB 3.0/USB 3.1 Gen 1 Hard Drives

• USB 3.0/USB 3.1 Gen 1 Drive Docks & Adapters

• USB 3.0/USB 3.1 Gen 1 Flash Drives & Readers

• USB 3.0/USB 3.1 Gen 1 Solid-state Drives

• USB 3.0/USB 3.1 Gen 1 RAIDs

• Optical Media Drives

• Multimedia Devices

• Networking

• USB 3.0/USB 3.1 Gen 1 Adapter Cards & Hubs

Compatibility

The good news is that USB 3.0/USB 3.1 Gen 1 has been carefully planned from the start to peacefully co-exist with USB 2.0. First of all,

while USB 3.0/USB 3.1 Gen 1 species new physical connections and thus new cables to take advantage of the higher speed capability of

the new protocol, the connector itself remains the same rectangular shape with the four USB 2.0 contacts in the exact same location as

before. Five new connections to carry receive and transmitted data independently are present on USB 3.0/USB 3.1 Gen 1 cables and only

come into contact when connected to a proper SuperSpeed USB connection.

Windows 8/10 will be bringing native support for USB 3.1 Gen 1 controllers. This is in contrast to previous versions of Windows, which

continue to require separate drivers for USB 3.0/USB 3.1 Gen 1 controllers.

10 Technology and components

Microsoft announced that Windows 7 would have USB 3.1 Gen 1 support, perhaps not on its immediate release, but in a subsequent Service

Pack or update. It is not out of the question to think that following a successful release of USB 3.0/USB 3.1 Gen 1 support in Windows 7,

SuperSpeed support would trickle down to Vista. Microsoft has conrmed this by stating that most of their partners share the opinion that

Vista should also support USB 3.0/USB 3.1 Gen 1.

USB Type-C

USB Type-C is a new, tiny physical connector. The connector itself can support various exciting new USB standards like USB 3.1 and USB

power delivery (USB PD).

Alternate Mode

USB Type-C is a new connector standard that is very small. It is about a third the size of an old USB Type-A plug. This is a single connector

standard that every device should be able to use. USB Type-C ports can support a variety of dierent protocols using “alternate modes,”

which allows you to have adapters that can output HDMI, VGA, DisplayPort, or other types of connections from that single USB port

USB Power Delivery

The USB PD specication is also closely intertwined with USB Type-C. Currently, smartphones, tablets, and other mobile devices often use

a USB connection to charge. A USB 2.0 connection provides up to 2.5 watts of power — that'll charge your phone, but that's about it. A

laptop might require up to 60 watts, for example. The USB Power Delivery specication ups this power delivery to 100 watts. It's bi-

directional, so a device can either send or receive power. And this power can be transferred at the same time the device is transmitting

data across the connection.

This could spell the end of all those proprietary laptop charging cables, with everything charging via a standard USB connection. You could

charge your laptop from one of those portable battery packs you charge your smartphones and other portable devices from today. You

could plug your laptop into an external display connected to a power cable, and that external display would charge your laptop as you used

it as an external display — all via the one little USB Type-C connection. To use this, the device and the cable have to support USB Power

Delivery. Just having a USB Type-C connection doesn't necessarily mean they do.

USB Type-C and USB 3.1

USB 3.1 is a new USB standard. USB 3's theoretical bandwidth is 5 Gbps, while USB 3.1's is 10 Gbps. That's double the bandwidth, as fast

as a rst-generation Thunderbolt connector. USB Type-C isn't the same thing as USB 3.1. USB Type-C is just a connector shape, and the

underlying technology could just be USB 2 or USB 3.0. In fact, Nokia's N1 Android tablet uses a USB Type-C connector, but underneath it's

all USB 2.0 — not even USB 3.0. However, these technologies are closely related.

Thunderbolt over Type-C

Thunderbolt is a hardware interface that combines data, video, audio, and power in a single connection. Thunderbolt combines PCI Express

(PCIe) and DisplayPort (DP) into one serial signal, and additionally provides DC power, all in one cable. Thunderbolt 1 and Thunderbolt 2 use

the same connector as miniDP (DisplayPort) to connect to peripherals, while Thunderbolt 3 uses a USB Type-C connector.

Technology and components 11

Figure 1. Thunderbolt 1 and Thunderbolt 3

1 Thunderbolt 1 and Thunderbolt 2 (using a miniDP connector)

2 Thunderbolt 3 (using a USB Type-C connector)

Thunderbolt 3 over Type-C

Thunderbolt 3 brings Thunderbolt to USB Type-C at speeds up to 40 Gbps, creating one compact port that does it all - delivering the

fastest, most versatile connection to any dock, display or data device like an external hard drive. Thunderbolt 3 uses a USB Type-C

connector/port to connect to supported peripherals.

1 Thunderbolt 3 uses USB Type-C connector and cables - It is compact and reversible

2 Thunderbolt 3 supports speed up to 40 Gbps

3 DisplayPort 1.2 – compatible with existing DisplayPort monitors, devices and cables

4 USB Power Delivery - Up to 130W on supported computers

Key Features of Thunderbolt 3 over USB Type-C

1 Thunderbolt, USB, DisplayPort and power on USB Type-C on a single cable (features vary between dierent products)

2 USB Type-C connector and cables which are compact and reversible

3 Supports Thunderbolt Networking (*varies between dierent products)

4 Supports up to 4K displays

5 Up to 40 Gbps

NOTE: Data transfer speed may vary between dierent devices.

Thunderbolt Icons

Figure 2. Thunderbolt Iconography Variations

12 Technology and components

Removing and installing components

Recommended tools

The procedures in this document require the following tools:

• Phillips #0 screwdriver

• Phillips #1 screwdriver

• Plastic scribe

NOTE: The #0 screw driver is for screws 0-1 and the #1 screw driver is for screws 2-4

Screw size list

Table 2. Precision 7530

Component Screw type Quantity Image

Keyboard M2.0x2.0 6

SSD thermal plate

M.2 SSD card

HDD Interposer board

WLAN card

WWAN

eDP bracket

Display panel

Power button board

Smart card cage

FPC beam connector

Palmrest

Display support bracket

M2.0x3.0 1 per SSD

1 per SSD

System board

Palmrest

Type-C bracket

LED board

Power connector port

M2.0x5.0 3

Removing and installing components 13

Component Screw type Quantity Image

GPU card 2

4 Cell Battery

6 Cell Battery

HDD assembly

M2.5x3.0 2

Display hinge M2.5x3.5 6

Hinge cap

Display assembly (bottom)

M2.5x4.0 4

Display assembly (rear) M2.5X6.0 2

HDD bracket M3.0x3.0 4

SD card

Removing SD card

1 Follow the procedure in Before working inside your computer.

2 Press the SD card in to release it from the system.

3 Slide the SD card out of the system.

14 Removing and installing components

Installing SD card

1 Slide the SD card into its slot until it clicks into place.

Removing and installing components 15

2 Follow the procedure in After working inside your computer.

Base cover

Removing the base cover

1 Follow the procedure in Before working inside your computer.

2 Remove the SD card.

3 To remove the base cover:

a Loosen the 7 captive screws that secure the base cover to the system [1].

b Pry open the base cover starting from the two recess point at the top edge of the system [2].

c Pry around all the edges of the base cover [3].

d Remove the base cover from the system [4].

16 Removing and installing components

NOTE: While pry open the base cover make sure to use hands or plastic scribe—do not use any other sharp objects as

it may damage the chassis

Installing the base cover

1 To install the base cover:

a Slide the base cover into its slot until it clicks into place [1, 2].

b Tighten the captive screws to secure the base cover to the system [3].

Removing and installing components 17

2 Install the SD cardSD card.

3 Follow the procedure in After working inside your computer.

Battery

Lithium-ion battery precautions

CAUTION:

• Exercise caution when handling Lithium-ion batteries.

• Discharge the battery as much as possible before removing it from the system. This can be done by disconnecting the AC adapter

from the system to allow the battery to drain.

• Do not crush, drop, mutilate, or penetrate the battery with foreign objects.

• Do not expose the battery to high temperatures, or disassemble battery packs and cells.

• Do not apply pressure to the surface of the battery.

• Do not bend the battery.

• Do not use tools of any kind to pry on or against the battery.

• If a battery gets stuck in a device as a result of swelling, do not try to free it as puncturing, bending, or crushing a Lithium-ion

battery can be dangerous. In such an instance, the entire system should be replaced. Contact https://www.dell.com/support for

assistance and further instructions.

• Always purchase genuine batteries from https://www.dell.com or authorized Dell partners and re-sellers.

18 Removing and installing components

Removing the battery

1 Follow the procedure in Before working inside your computer.

2 Remove the:.

aSD card

bbase cover

3 To remove the 6-cell battery:

a Disconnect the battery cable from the connector on the battery [1].

b Remove the 3 (M2.5x3.0) screws that secure the battery to the system [2].

c Remove the battery away from the system [3].

4 To remove the 4-cell battery:

a Disconnect the battery cable from the connector on the battery [1].

b Remove the 2 (M2.5x3.0) screws that secure the battery to the system [2].

c Remove the battery away from the system [3].

Removing and installing components 19

Installing the battery

1 To install the 6-cell battery:

a Place the battery onto its slot in the system [1].

b Replace the 3 (M2.5x3.0) screws to secure the battery to the system [2].

c Connect the battery cable to the connector in the battery [3].

20 Removing and installing components

2 To install the 4-cell battery:

a Place the battery onto its slot in the system [1].

b Replace the 2 (M2.5x3.0) screws to secure the battery to the system [2].

c Connect the battery cable to the connector in the system board [3].

Removing and installing components 21

3 Install the:

abase cover

bSD card

4 Follow the procedure in After working inside your computer.

Hard drive

Removing the hard drive assembly

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

3 To remove hard drive assembly:

a Remove the 4 (M2.5x3.0) screws that secure the hard drive assembly to the system [1].

b Pull the tab on the hard drive assembly to disconnect the hard drive assembly from the hard drive connector [2].

22 Removing and installing components

c Remove the hard drive assembly from the system.

d Remove the 4 (M3.0x3.0) screws that secure the hard drive assembly to the hard drive bracket.

e Remove the hard drive from the hard drive bracket.

Installing the hard drive assembly

1 To install the hard drive assembly:

a Place the hard drive to the hard drive bracket and replace the 4 (M3.0x3.0) screws to secure the hard drive to the hard drive

bracket.

Removing and installing components 23

b Insert the hard drive assembly into its slot in the system [1].

c Replace the 4 (M2.5x3.0) screws to secure the hard drive assembly to the system [2].

2 Install the:

abase cover

bSD card

3 Follow the procedure in After working inside your computer.

Hard drive interposer board

Removing the hard drive interposer board

1 Follow the procedures in Before working inside your computer.

2 Remove the:

24 Removing and installing components

aSD card

bbase cover

chard drive

3 To remove the hard drive interposer board:

a Remove the 2 (M2.0x3.0) screws that secure the hard drive interposer to the system board [1].

b Remove the hard drive interposer board from the system [2].

Installing the hard drive interposer board

1 To install the hard drive interposer board:

a Align the hard drive interposer board into its position on the system [1].

b Replace the 2 (M2.0x3.0) screws to secure the hard drive interposer to the system board [2].

Removing and installing components 25

2 Install the:

ahard drive

bbase cover

cSD card

3 Follow the procedure in After working inside your computer.

Keyboard lattice and Keyboard

Removing the keyboard

1 Follow the procedures in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

3 To remove the keyboard:

a Lift the latch and disconnect the keyboard cable, ngerprint cable and the ngerprint button cable from the connectors on the

system board.

26 Removing and installing components

b Turn-over and open the system at 90° angle.

c Using a plastic scribe pry the keyboard lattice starting from the recess points on the top edge [1,2] and work along the sides and

bottom edge of the keyboard lattice.

Removing and installing components 27

d Lift the keyboard lattice away from the system.

28 Removing and installing components

e Remove the 6 (M2.0x2.0) screws that secure the keyboard to the palmrest [1].

f Pry the bottom edge of the keyboard and then work along the left and right sides of the keyboard [2,3,4].

g Slide and remove the keyboard from the system.

Removing and installing components 29

Installing the keyboard

1 To Install the keyboard:

a Align the keyboard and route the cables back through to the bottom of the compartment.

b Press and align the keyboard to its compartment working along the left, right and bottom edges [1,2,3].

c Replace the 6 (M2.0x2.0) screws to secure the keyboard to the palmrest [4].

30 Removing and installing components

d Align the keyboard lattice to its position on the keyboard and ensure that the keyboard lattice clicks into its place.

e Turn-over the system at 90° angle to access the keyboard cables.

f Connect the keyboard cable, ngerprint cable and ngerprint button cable to the connectors on the system board.

Removing and installing components 31

NOTE: Ensure that you fold the keyboard data cable in perfect alignment.

3 Install the:

abattery

bbase cover

cSD card

4 Follow the procedure in After working inside your computer.

Memory modules

Removing the primary memory module

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

3 To remove primary memory module:

a Pry the retention clips away from the memory module until it pops up.

b Lift the memory module and remove it from the system.

32 Removing and installing components

Installing the primary memory module

1 To Install the primary memory module:

a Insert the memory module into the memory socket.

b Press the clips to secure the memory module to the system board.

Removing and installing components 33

2 Install the:

abattery

bbase cover

cSD card

3 Follow the procedure in After working inside your computer.

Removing the secondary memory module

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

dkeyboard

3 To remove the secondary memory module:

a Remove the single (M2.0x3.0) screw that secures the memory shield [1].

b Slide and lift the memory shield from the memory module on the system [2].

c Pry the retention clips away from the memory module until it pops up [3].

d Lift the memory module and remove it from the system [4].

34 Removing and installing components

NOTE: Repeat step (c) and (d) if there is another memory installed.

Installing the secondary memory module

1 To install the secondary memory module:

a Insert the memory module into the memory socket [1].

b Press the clips to secure the memory module to the system board [2].

c Slide in the memory shield on the memory module [3].

d Replace the single (M2.0x3.0) screw to secure the memory shield to the memory module [4].

Removing and installing components 35

2 Install the:

akeyboard

bbattery

cbase cover

dSD card

3 Follow the procedure in After working inside your computer.

WWAN card

Removing WWAN card

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

3 To remove the WWAN card:

a Remove the single (M2.0x3.0) screw that secures the WWAN metal bracket to the system board [1].

b Remove the WWAN metal bracket that secures the WWAN antenna cables [2].

c Disconnect and unroute the WWAN antenna cables connected to the WWAN card [3].

d Remove the WWAN card from the WWAN card slot in the system board [4].

36 Removing and installing components

Installing the WWAN card

1 To install the WWAN card:

a Slide the WWAN card to the WWAN card slot on the system board [1].

b Route the WWAN antenna cables through the routing channel.

c Connect the antenna cables to the connectors on the WWAN card [2].

d Align the WWAN metal bracket above the WWAN card and replace the single (M2.0x3.0) screw to secure the WWAN metal

bracket to the system board [3,4].

Removing and installing components 37

2 Install the:

abattery

bbase cover

cSD card

3 Follow the procedure in After working inside your computer.

WLAN card

Removing the WLAN card

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

3 To remove the WLAN card:

a Remove the single (M2.0x3.0) screw that secures the WLAN metal bracket to the system board [1].

b Remove the WLAN metal bracket that secures the WLAN antenna cables [2].

c Disconnect and un-route the antenna cables connected to the WLAN card [3].

d Remove the WLAN card from the WLAN card slot in the system board [4].

38 Removing and installing components

Installing the WLAN card

1 To install the WLAN card:

a Slide the WLAN card to the WLAN card slot in the system board [1].

b Route the WLAN antenna cables through the routing channel.

c Connect the antenna cables to the connectors in the WLAN card [2].

d Align the WLAN metal bracket above the WLAN card and replace the single (M2.0x3.0) screw to secure the WLAN metal

bracket to the system board [3,4].

Removing and installing components 39

2 Install the:

abattery

bbase cover

cSD card

3 Follow the procedure in After working inside your computer.

Solid State Drive — optional

Removing the M.2 Solid State Drive—SSD module

1 Follow the procedures in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

3 To remove the M.2 SSD module (Slot 4):

a Remove the single (M2.0x3.0) screw that secures the thermal plate to the system [1].

b Slide and remove the thermal plate [2].

c Remove the single (M2.0x3.0) screw that secures the M.2 SSD to the system board [3].

d Remove the M.2 SSD from the system [4].

NOTE: Repeat the above steps for removal of other M.2 SSD installed (Slot 3 and 5).

40 Removing and installing components

Removing and installing components 41

42 Removing and installing components

Installing the M.2 SSD module

1 To install the M.2 SSD module (Slot 4):

a Place the M.2 SSD into its slot in the system [1].

b Replace the single (M2.0x3.0) screw to secure the M.2 SSD to the system board [2].

c Place the thermal plate above the M.2 SSD module [3].

d Replace the single (M2.0x3.0) screw to secure the thermal plate to the M.2 SSD [4].

NOTE: Repeat the above steps to install other M.2 SSD installed (Slot 3 and 5).

Removing and installing components 43

44 Removing and installing components

2 Install the:

abattery

bbase cover

NOTE: Installing of base cover is required only if the M.2 SSD module in slot 3 or 5 are accessed.

cSD card

3 Follow the procedure in After working inside your computer.

Coin-cell battery

Removing the coin cell battery

1 Follow the procedures in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

dpalmrest

3 To remove coin cell battery:

a Disconnect the coin cell battery cable from the system [1].

b Pry and lift the coin cell battery from the system [2].

Removing and installing components 45

CAUTION: Disconnecting coin cell battery may reset BIOS settings, time and date within System Settings, cause

BitLocker or other security resets.

Installing the coin cell battery

1 To install the coin cell battery:

a Replace the coin cell battery in its slot on the system.

b Connect the coin cell battery cable to the system.

46 Removing and installing components

2 Install the:

apalmrest

bbattery

cbase cover

dSD card

3 Follow the procedure in After working inside your computer.

Power connector port

Removing the power connector port

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

3 To remove power connector port:

a Disconnect the power connector cable from the connector on the system board [1].

b Peel the adhesive tape that secures the power connector cable to the system and unroute the cable [2, 3].

Removing and installing components 47

c Remove the single (M2.0x5.0) screw that secures the power connector cable metal bracket to the system [1].

d Remove the metal bracket away from the system [2].

e Lift the power connector port from the system [3].

48 Removing and installing components

Installing the power connector port

1 To install the power connector port:

a Connect the power connector port to the system [1].

b Place the power connector cable metal bracket [2].

c Replace the single (M2.0x5.0) screw to secure the metal bracket to the system [3].

Removing and installing components 49

dAx the adhesive tape to secure the power connector cable in place [1].

e Route the cable through the routing channel and ax the adhesive tape [2].

f Connect the power connector cable to the connector on the system board [3].

50 Removing and installing components

2 Install the:

abattery

bbase cover

cSD card

3 Follow the procedure in After working inside your computer.

Palm rest

Removing the palmrest

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

dkeyboard

ehard drive

3 To remove the palmrest:

a Lift the latch and disconnect the touchpad cable from the connector on the system board [1].

b Remove the 11 (M2.0x5.0) and the 2 (M2.0x3.0) screws that secure the palmrest assembly in place [2, 3].

Removing and installing components 51

c Turn the system around and disconnect the system board cable and power button cable from the connectors on the system

board [1, 2].

d Remove the 2 (M2.0x3.0) screws that secure the palmrest to the system [3].

52 Removing and installing components

e Push the hole at the bottom of the system to release the palmrest from the bottom chassis.

f Lift and remove the palmrest from the system.

Removing and installing components 53

Installing the palmrest

1 To install the palmrest:

a Align the palmrest on the system and press until it snaps in its place .

54 Removing and installing components

b Replace the 2 (M2.0x3.0) screws to secure the palmrest to the system [1].

c Connect the system board and power button cable to the connectors on the system board [2,3].

Removing and installing components 55

d Turn the system and replace the 2 (M2.0x3.0) and the 11 (M2.0x5.0) screws to secure the palmrest to the system [1, 2].

e Connect the touchpad cable to the connector on the system board and lock the latch [3].

2 Install the:

akeyboard

bhard disk

cbattery

dbase cover

eSD card

3 Follow the procedure in After working inside your computer.

Touchpad button

Removing the Touchpad buttons

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

dkeyboard

ehard drive

fpalmrest

3 To remove touchpad buttons:

a Disconnect the touchpad cable from the touchpad [1].

b Remove the 2 (M2.0x3.0) screws that secure the touchpad buttons to the palmrest [2].

56 Removing and installing components

c Remove the touchpad button from the palmrest [3].

Installing the Touchpad button

1 To install the touchpad button:

a Place the touchpad button into its slot in the palmrest [1].

b Replace the 2 (M2.0x3.0) screws to secure the touchpad button to the palmrest [2].

c Connect the touchpad button cable to the connector in the touchpad [3].

Removing and installing components 57

2 Install the:

apalmrest

bhard drive

ckeyboard

dbattery

ebase cover

fSD card

3 Follow the procedure in After working inside your computer.

SIM card

Removing SIM card

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

3 To remove SIM card:

a Gently slide the SIM card cover towards the rear of the system to unlock the SIM card cover [1].

CAUTION: The SIM card cover is very fragile and can be easily damaged if it is not properly unlocked before opening.

b Filp the SIM card cover from the botton edge [2].

c Lift the SIM card from the SIM card compartment [3].

58 Removing and installing components

Installing SIM card

1 To install the SIM card:

a Slide the SIM card into the SIM card compartment [1].

b Snap the SIM card cover down [2].

c Slide the SIM card cover towards the front of the system to lock the SIM card cover [3].

Removing and installing components 59

2 Install the:

abattery

bbase cover

cSD card

3 Follow the procedure in After working inside your computer.

Smart card cage

Removing the smart card cage

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

dkeyboard

ehard drive

fpalmrest

3 To remove power switch board:

a Disconnect the smart card cage cable from the connector on the system board [1].

b Pry the smart card cage cable.

c Remove the 2 (M2.0X3.0) screws that secure the smart card cage to the system [3].

d Remove the smart card cage from the system [4].

60 Removing and installing components

Installing the smart card cage

1 To install the smart card cage:

a Place the smart card cage into its slot in the system [1].

b Replace the 2 (M2.0X3.0) screws to secure the smart card cage to the system [2].

cAx the smart card cable [3].

d Connect the smart card cage cable to the connector on the system [4]

Removing and installing components 61

2 Install the:

apalmrest

bhard drive

ckeyboard

dbattery

ebase cover

fSD card

3 Follow the procedure in After working inside your computer.

Speaker

Removing the speakers

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

dkeyboard

ehard drive

fpalmrest

3 To remove the speaker:

a Disconnect the speaker cable from the system board [1].

b Unroute the speaker cable and remove the cable from the routing channels.

c Lift the speakers, along with the speaker cable and remove it away from the system [2].

62 Removing and installing components

Installing the speakers

1 To install the speaker:

a Align the speakers along the slots on the system [1].

b Route the speaker cable through the routing channels on the system.

c Connect the speaker cable to the connector on the system board [2].

Removing and installing components 63

2 Install the:

apalmrest

bhard drive

ckeyboard

dbattery

ebase cover

fSD card

3 Follow the procedure in After working inside your computer.

LED board

Removing the LED board

1 Follow the procedures in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

dkeyboard

ehard drive

fpalmrest

3 To remove LED board:

a Lift the tab and disconnect the LED-board cable from the system board [1].

64 Removing and installing components

b Peel the LED-board cable from the system.

c Remove the single (M2.0x5.0) screw that secures the LED board to the system [2].

d Remove the LED board from the system [3].

Installing the LED board

1 To install the LED board:

a Align the LED board to its original position on the system [1].

b Replace the single (M2.0x5.0) screw to secure the LED board to the system [2].

cAx the LED-board cable.

d Connect the LED-board cable to the connector in the system board [3].

Removing and installing components 65

2 Install the:

apalmrest

bhard drive

ckeyboard

dbattery

ebase cover

fSD card

3 Follow the procedure in After working inside your computer.

Heat sink assembly

Removing the heat sink assembly

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

dkeyboard

ehard drive

fpalmrest

3 To remove heat sink:

a Remove the 2 (M2.0x3.0) screw that secures the eDP cable bracket to the system board [1].

66 Removing and installing components

b Remove the eDP cable bracket from the system [2].

c Disconnect the eDP cable from the connector on the system board [3].

d Pry the adhesive tape that secures the eDP cable in place.

e Disconnect the two fan cables from the connector on the system board [4,5].

f Loosen the 4 captive screws that secure the heat sink assembly to the system board [1].

NOTE: Remove the captive screws in the order stamped onto the heat sink next to the screws [1 > 2 > 3 > 4].

g Lift the heat sink assembly [2].

Removing and installing components 67

h Slide and remove the heat sink assembly from the system.

68 Removing and installing components

Installing the heat sink assembly

1 To install the heat sink assembly:

a Insert the heat-sink assembly in its slot on the system [1].

b Tighten the 4 captive screws to secure the heat-sink assembly to the system board [2].

NOTE: Tighten the captive screws in the order stamped onto the heat sink next to the screws [1 > 2 > 3 > 4].

Removing and installing components 69

c Connect the two fan cables to the connector on the system board [1, 2].

dAx the adhesive tape to secure the eDP cable in place.

e Connect the eDP cable to the connector on the system board [3].

f Place and align the eDP cable bracket above the display cable connector [4].

g Replace the 2 (M2.0x3.0) screw to secure the eDP cable bracket to the system board [5].

70 Removing and installing components

2 Install the:

apalmrest

bhard drive

ckeyboard

dbattery

ebase cover

fSD card

3 Follow the procedure in After working inside your computer.

Graphics card

Removing the graphics card

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

dkeyboard

ehard drive

fpalmrest

gheatsink assembly

3 To remove the graphics card:

Removing and installing components 71

a Remove the 2 (M2.0x3.0) screws that secure the beam connector to the system board [1].

b Remove the beam connector from the system board [2].

c Remove the 2 (M2.0x5.0) screws that secure the graphics card to the system board [3].

d Remove the graphics card from the system [4].

NOTE: The above procedures are for UMA graphics card. Systems shipped with UMA GPU card do not have GPU power

cable. However, for discrete models shipped with either a 128 MB or 256 MB VRAM GPU card, you need to disconnect the

GPU power cable before removing the GPU card.

Installing the graphics card

1 To Install the graphics card:

a Slide the graphics card into its original position in the system [1].

b Replace the 2 (M2.0x5.0) screws to secure the graphics card to the system board [2].

c Replace the beam connector [3].

d Replace the 2 (M2.0x3.0) screws to secure the beam connector to the system board [4].

72 Removing and installing components

2 NOTE: The above procedures are for UMA graphics card. Systems shipped with UMA GPU card do not have GPU power

cable. However, for discrete models shipped with either a 128 MB or 256 MB VRAM GPU card, you need to connect the

GPU power cable after installing the GPU card.

Install the:

aheat sink assembly

bpalmrest

chard drive

dkeyboard

ebattery

fbase cover

gSD card

3 Follow the procedure in After working inside your computer.

System board

Removing the system board

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

dhard drive

Removing and installing components 73

ehard drive interposer board

fkeyboard

gprimary memory

hsecondary memory

iWLAN card

jWWAN card

kM.2 SSD card

lSIM card

mpalmrest

nheat sink assembly

ographic card

3 To disconnect the system board:

a Disconnect the power connector cable from the connector on the system board .

b Remove the 3 (M2.0x5.0) screws that secure the Type-C USB bracket to the system [1].

c Remove the Type-C USB bracket from the system [2].

d Disconnect the touchpad cable, LED board cable and speaker from the connectors on the system board [3, 4, 5] and peel the

coin cell battery from the system [6].

74 Removing and installing components

e Remove the 3 (M2.0x5.0) screws that secure the system board in place [1].

f Lift the right side of the system board and remove the system board from the system chassis [2, 3].

Removing and installing components 75

Installing the system board

1 To install the system board:

a Align the system board into its original position on the system [1, 2].

b Replace the 3 (M2.0x5.0) screws to secure the system board in place [3].

76 Removing and installing components

c Connect the touchpad cable, LED board cable and speaker to the connectors on the system board [4, 3, 2] and ax the coin cell

battery to the system [1].

d Place the Type-C USB bracket onto its slot on the system [5].

e Replace the 3 (M2.0x5.0) screws to secure the Type-C USB bracket to the system [6].

Removing and installing components 77

f Connect the power connector cable to the connector on the system board.

78 Removing and installing components

2 Install the:

agraphic card

bheat sink assembly

cpalmrest

dSIM card

eM.2 SSD card

fWWAN card

gWLAN card

hprimary memory

isecondary memory

jkeyboard

khard drive interposer board

lhard drive

mbattery

nbase cover

oSD card

3 Follow the procedure in After working inside your computer.

Display assembly

Removing the display assembly

1 Follow the procedure in Before working inside your computer.

2 Remove the:

Removing and installing components 79

aSD card

bbase cover

cbattery

dkeyboard

ehard drive

fWWAN card

gWLAN card

hpalmrest

3 To remove display assembly:

a Remove the 2 (M2.5x4.0) screws at the bottom of the system that secures the display assembly in place [1].

b Unroute all the wireless antenna cables from the routing channels at the bottom of the system [2] and unthread the antenna

cables.

c Remove the 2 (M2.5x6.0) screws at the rear of the system that secures the display assembly in place.

80 Removing and installing components

d Open the display assembly to a 180-degree angle.

e Remove the 4 (M2.5x4.0) screws that secures the display hinge caps to the system [1].

f Remove the display hinge caps from the system [2].

g Remove the 2 (M2.0x3.0) screws that secure the eDP cable bracket to the system board [1].

h Remove the eDP cable bracket [2].

Removing and installing components 81

i Disconnect the eDP cable from the connector on the system board [3].

j Peel the adhesive tape that secures the eDP cable in place [4].

k Unroute the wireless cable from the routing channels located next to the hinges [5].

l Remove the display assembly [6].

Installing the display assembly

1 To install display assembly:

a Align the display assembly into the slots on the system [1].

b Route the wireless cable located next to the hinges [2].

cAx the adhesive tape to secure the eDP cable in place [3].

d Connect the eDP cable to the connector on the system board [4].

e Place the eDP cable bracket and replace the 2 (M2.0x3.0) screws to secure the eDP cable bracket to the system board [5, 6].

82 Removing and installing components

f Align the display hinge caps and replace the 4 (M2.5x4.0) screws to secure the display hinge caps to the system [1, 2].

g Close the display assembly and replace the 2 (M2.5x6.0) screws at the rear of the system to secure the display assembly in

place.

Removing and installing components 83

h Route all the wireless antenna cables to the routing channels at the bottom of the system [1].

i Replace the 2 (M2.5x4.0) screws at the bottom of the system to secure the display assembly in place [2].

84 Removing and installing components

2 Install the:

apalmrest

bWWAN card

cWLAN card

dhard drive

ekeyboard

fbattery

gbase cover

hSD card

3 Follow the procedure in After working inside your computer.

Display bezel

Removing the display bezel

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

dkeyboard

ehard drive

fWWAN card

Removing and installing components 85

gWLAN card

hpalmrest

idisplay assembly

3 To remove display bezel:

a Using a plastic scribe pry the two recess points at the bottom edge of the display bezel [1].

b Pry around the sides and top edge of the display bezel [2, 3, 4].

NOTE: While prying the display bezel, make sure to pry along the outside edge of the display bezel using your hands-

using a screw driver or other sharp objects may damage the display cover.

NOTE: The display bezel shipped with a non-touch display is a disposable part and should be replaced with a new display

bezel anytime it is removed from the system.

Installing the display bezel

1 To install the display bezel:

a Place the display bezel on the display assembly.

b Press the edges of the display bezel until it clicks onto the display assembly [1, 2, 3, 4].

86 Removing and installing components

2 Install the:

adisplay assembly

bpalmrest

cWWAN card

dWLAN card

ehard drive

fkeyboard

gbattery

hbase cover

iSD card

3 Follow the procedure in After working inside your computer.

Display hinges

Removing the display hinge

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

dkeyboard

ehard drive

fWWAN card

gWLAN card

hpalmrest

idisplay assembly

Removing and installing components 87

jdisplay bezel

kdisplay panel

3 To remove display hinge:

a Remove the 6 (M2.5x3.5) screws that secure the display hinges to the display assembly [1].

b Remove the display hinges [2].

Installing the display hinge

1 To install display hinge:

a Place the display hinge in its slot on the display assembly [1].

b Replace the 6 (M2.5x3.5) screws to secure the display hinge to the display assembly [2].

88 Removing and installing components

2 Install the:

adisplay panel

bdisplay bezel

cdisplay assembly

dpalmrest

eWWAN card

fWLAN card

ghard drive

hkeyboard

ibattery

jbase cover

kSD card

3 Follow the procedure in After working inside your computer.

Display panel

Removing the display panel

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

dkeyboard

ehard drive

fWWAN card

gWLAN card

Removing and installing components 89

hpalmrest

idisplay assembly

jdisplay bezel

3 To remove screws from the display panel :

a Remove the 4 (M2.0X3.0) screws that secure the display panel to the display assembly [1].

b Lift the display panel and turn the display panel over to access the eDP cable [2].

4 To remove display panel:

a Peel the adhesive tape to access the eDP cable [1].

b Peel the adhesive tapes that secures the eDP cable [2, 3].

c Lift the metal tab and disconnect the eDP cable from the connector on the display panel [4, 5].

90 Removing and installing components

5 Remove the display panel.

Installing the display panel

1 To install the display panel:

a Connect the eDP cable to the connector on the back of the display panel and ax the adhesive tape [1, 2, 3, 4, 5].

Removing and installing components 91

b Align the display panel with the tabs on the display assembly.

c Replace the 4 (M2.0X3) screws to secure the display panel to the display assembly.

92 Removing and installing components

2 Install the:

adisplay bezel

bdisplay assembly

cpalmrest

dWWAN card

eWLAN card

fhard drive

gkeyboard

hbattery

ibase cover

jSD card

3 Follow the procedure in After working inside your computer.

Camera

Removing the camera

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

dkeyboard

ehard drive

Removing and installing components 93

fWWAN card

gWLAN card

hpalmrest

idisplay assembly

jdisplay bezel

kdisplay panel

3 To remove camera:

a Peel the adhesive tape that covers the camera module [1].

b Disconnect the eDP cable from the camera module [2].

c Carefully pry the camera module from the system [3].

Installing the camera

1 To install the camera:

a Place the camera module in its slot on the system [1].

b Connect the eDP cable to the camera module [2].

cAx the adhesive tape to cover the camera module [3].

94 Removing and installing components

2 Install the:

adisplay panel

bdisplay bezel

cdisplay assembly

dpalmrest

eWWAN card

fWLAN card

ghard drive

hkeyboard

ibattery

jbase cover

kSD card

3 Follow the procedure in After working inside your computer.

eDP cable

Removing the eDP cable

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

dkeyboard

ehard drive

fWWAN card

Removing and installing components 95

gWLAN card

hpalmrest

idisplay assembly

jdisplay bezel

kdisplay panel

3 To remove eDP cable:

a Peel the adhesive tape covering the camera module [1].

b Disconnect the eDP cable from the camera module [2].

c Peel the eDP cable from the display cover and unroute the cable from the routing channels [3].

d Remove the eDP cable from the system.

Installing the eDP cable

1 To install eDP cable:

a Route and ax the eDP cable on the display cover [3].

b Connect the eDP cable to the connector on the camera module [2].

cAx the adhesive tape covering the camera module [1].

96 Removing and installing components

2 Install the:

adisplay panel

bdisplay bezel

cdisplay assembly

dpalmrest

eWWAN card

fWLAN card

ghard drive

hkeyboard

ibase cover

jbattery

kSD card

3 Follow the procedure in After working inside your computer.

Display bracket

Removing the display support bracket

1 Follow the procedure in Before working inside your computer.

2 Remove the:

aSD card

bbase cover

cbattery

dkeyboard

ehard drive

fWWAN card

Removing and installing components 97

gWLAN card

hpalmrest

idisplay assembly

jdisplay bezel

kdisplay panel

ldisplay hinge

3 To remove display bracket:

a Peel the adhesive tape that covers the display support bracket [1].

b Remove the 6 (M2.0x3.0) screws that secure the display support brackets to the display cover [2].

c Remove the display support brackets from the display cover [3].

Installing the display support bracket

1 To install the display support bracket:

a Place the display brackets onto its slot on the display cover [1].

b Replace the 6 (M2.0x3.0) screws to secure the display bracket to the display cover [2].

cAx the adhesive tape to cover the display support bracket [3].

98 Removing and installing components

2 Install the:

adisplay hinge

bdisplay panel

cdisplay bezel

ddisplay assembly

epalmrest

fWWAN card

gWLAN card

hhard drive

ikeyboard

jbattery

kbase cover

lSD card

3 Follow the procedure in After working inside your computer.

Removing and installing components 99

Troubleshooting

Enhanced Pre-Boot System Assessment — ePSA

diagnostics

The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware. The ePSA is embedded with the

BIOS and is launched by the BIOS internally. The embedded system diagnostics provides a set of options for particular devices or device

groups allowing you to:

• Run tests automatically or in an interactive mode

• Repeat tests

• Display or save test results

• Run thorough tests to introduce additional test options to provide extra information about the failed device(s)

• View status messages that inform you if tests are completed successfully

• View error messages that inform you of problems encountered during testing

CAUTION: Use the system diagnostics to test only your computer. Using this program with other computers may cause invalid

results or error messages.

NOTE: Some tests for specic devices require user interaction. Always ensure that you are present at the computer terminal

when the diagnostic tests are performed.

Running the ePSA Diagnostics

Invoke diagnostics boot by either of the methods that are suggested below:

1 Power on the computer.

2 As the computer boots, press the F12 key when the Dell logo is displayed.

3 In the boot menu screen, use Up/Down arrow key to select the Diagnostics option and then press Enter.

NOTE: The Enhanced Pre-boot System Assessment window displays, listing all devices detected in the computer. The

diagnostics starts running the tests on all the detected devices.

4 Press the arrow in the lower-right corner to go to the page listing.

The detected items are listed and tested.

5 To run a diagnostic test on a specic device, press Esc and click Yes to stop the diagnostic test.

6 Select the device from the left pane and click Run Tests.

7 If there are any issues, error codes are displayed.

Note the error code and contact Dell.

8 Shut down the computer.

9 Press and hold the Fn key, while pressing the power button, and then release both.

10 Repeat steps 3–7 above.

100 Troubleshooting

Diagnostic LED

This section details the diagnostic features of the battery LED.

Instead of beep codes, errors are indicated via the bicolor Battery Charge/Status LED. A specic blink pattern is followed by ashing a

pattern of ashes in amber, followed by white. The pattern then repeats.

NOTE: he diagnostic pattern will consist of a two digit number being represented by a rst group of LED blinks (1 through 9) in

amber, followed by a 1.5 second pause with the LED o, and then a second group of LED blinks (1 through 9) in white. This is

then followed by a three second pause, with the LED o, before repeating over again. Each LED blink takes 0.5 seconds.

The system will not shutdown when displaying the Diagnostic Error Codes.

Diagnostic Error Codes will always supersede any other use of the LED. For instance, on Notebooks, battery codes for Low Battery or

Battery Failure situations will not be displayed when Diagnostic Error Codes are being displayed.

Table 3. Diagnostic LED

Blinking Pattern Possible Problem Suggested Resolution

Amber White

2 1 CPU failure Replace the system board

2 2 System Board failure (included BIOS corruption or ROM error) Flash latest BIOS version. If

problem persists, replace the

system board

2 3 No Memory/ RAM detected Conrm that the memory

module is installed properly. If

problem persists, replace the

memory module

2 4 Memory / RAM failure Replace the memory module

2 5 Invalid memory installed Replace the memory module

2 6 System board / Chipset Error / Clock failure / Gate A20 failure /

Super I/O failure / Keyboard controller failure

Replace the system board

2 7 LCD failure Replace the LCD

3 1 RTC power failure Replace the CMOS battery

3 2 PCI or Video card/chip failure Replace the system board

3 3 BIOS Recovery image not found Flash latest BIOS version. If

problem persists, replace the

system board

3 4 BIOS Recovery image found but invalid Flash latest BIOS version. If

problem persists, replace the

system board

Battery status LED

Table 4. Battery status LED

Power Source LED behavior System Power State Battery Charge Level

AC Adapter Solid White S0 0-100%

AC Adapter Solid White S4/S5 < Fully Charged

Troubleshooting 101

Power Source LED behavior System Power State Battery Charge Level

AC Adapter O S4/S5 Fully Charged

Battery Amber S0 < = 10%

Battery O S0 > 10%

Battery O S4/S5 0-100%

•S0 (ON) — System is turned on.

•S4— The system consumes the least power compared to all other sleep states. The system is almost at an OFF state, expect for a

trickle power. The context data is written to hard drive.

•S5 (OFF) — The system is in a shutdown state.

102 Troubleshooting

Getting help

Contacting Dell

NOTE: If you do not have an active Internet connection, you can nd contact information on your purchase invoice, packing slip,

bill, or Dell product catalog.

Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services

may not be available in your area. To contact Dell for sales, technical support, or customer service issues:

1 Go to Dell.com/support.

2 Select your support category.

3 Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.

4 Select the appropriate service or support link based on your need.

Getting help 103

Table of Contents

DELL 7530 User Manual

Related Manuals