Table of Contents
- XPS 8920 Service Manual
- Before working inside your computer
- After working inside your computer
- Technical overview
- Removing the right-side cover
- Replacing the right-side cover
- Removing the top cover
- Replacing the top cover
- Removing the bottom cover
- Replacing the bottom cover
- Removing the front bezel
- Replacing the front bezel
- Removing the primary hard-drive
- Replacing the primary hard-drive
- Removing the primary hard-drive
- Replacing the primary hard-drive
- Removing the secondary hard-drive
- Replacing the secondary hard-drive
- Removing the solid-state drive
- Replacing the solid-state drive
- Removing the power-supply unit
- Replacing the power-supply unit
- Removing the coin-cell battery
- Replacing the coin-cell battery
- Removing the chassis fan
- Replacing the chassis fan
- Removing the graphics card
- Replacing the graphics card
- Removing the full-length graphics cards
- Replacing the full-length graphics cards
- Removing the memory modules
- Replacing the memory modules
- Removing the optical drive
- Replacing the optical drive
- Removing the power-button module
- Replacing the power-button module
- Removing the top I/O-panel
- Replacing the top I/O-panel
- Removing blower and heat-sink assembly
- Replacing blower and heat-sink assembly
- Removing the processor fan and heat-sink assembly
- Replacing the processor fan and heat-sink assembly
- Removing the processor
- Replacing the processor
- Removing the wireless card
- Replacing the wireless card
- Removing the antenna
- Replacing the antenna
- Removing the system board
- Replacing the system board
- Flashing the BIOS
- BIOS setup program
- Diagnostics
- Getting help and contacting Dell
DELL 8920 User Manual
Displayed below is the user manual for 8920 by DELL which is a product in the PCs/Workstations category. This manual has pages.
Related Manuals
XPS 8920
Service Manual
Computer Model: XPS 8920
Regulatory Model: D24M
Regulatory Type: D24M001
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make
better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or
loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.
Copyright © 2017 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other
trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be
trademarks of their respective owners.
2017 - 01
Rev. A00
Contents
Before working inside your computer........................... 10
Before you begin .....................................................................................10
Safety instructions...................................................................................10
Recommended tools................................................................................. 11
Screw list................................................................................................. 12
After working inside your computer.............................. 14
Technical overview....................................................... 15
Inside view of your computer................................................................... 16
System-board components...................................................................... 17
Removing the right-side cover......................................19
Procedure................................................................................................ 19
Replacing the right-side cover......................................21
Procedure................................................................................................22
Removing the top cover...............................................23
Prerequisites............................................................................................23
Procedure................................................................................................23
Replacing the top cover............................................... 25
Procedure............................................................................................... 25
Post-requisites........................................................................................ 25
3
Removing the bottom cover.........................................26
Prerequisites............................................................................................26
Procedure............................................................................................... 26
Replacing the bottom cover.........................................28
Procedure................................................................................................28
Post-requisites........................................................................................ 28
Removing the front bezel ............................................29
Prerequisites........................................................................................... 29
Procedure............................................................................................... 30
Replacing the front bezel............................................. 32
Procedure................................................................................................32
Post-requisites........................................................................................ 32
Removing the primary hard-drive.................................33
Prerequisites............................................................................................33
Procedure (with tabs)............................................................................. 33
Replacing the primary hard-drive ................................ 36
Procedure (with tabs)............................................................................. 36
Post-requisites........................................................................................ 36
Removing the primary hard-drive................................. 37
Prerequisites............................................................................................37
Procedure (with screws)......................................................................... 37
Replacing the primary hard-drive .................................41
Procedure................................................................................................ 41
Post-requisites......................................................................................... 41
4
Removing the secondary hard-drive.............................42
Prerequisites............................................................................................42
Procedure................................................................................................42
Replacing the secondary hard-drive.............................46
Post-requisites........................................................................................ 46
Procedure............................................................................................... 46
Removing the solid-state drive.....................................47
Prerequisites............................................................................................47
Procedure................................................................................................47
Replacing the solid-state drive.....................................49
Procedure............................................................................................... 49
Post-requisites........................................................................................ 50
Removing the power-supply unit..................................52
Prerequisites........................................................................................... 52
Procedure............................................................................................... 52
Replacing the power-supply unit..................................56
Procedure............................................................................................... 56
Post-requisites........................................................................................ 56
Removing the coin-cell battery.................................... 57
Prerequisites............................................................................................57
Procedure................................................................................................57
Replacing the coin-cell battery.................................... 59
Procedure............................................................................................... 59
Post-requisites........................................................................................ 59
5
Removing the chassis fan............................................ 60
Prerequisites........................................................................................... 60
Procedure............................................................................................... 60
Replacing the chassis fan.............................................63
Procedure............................................................................................... 63
Post-requisites........................................................................................ 63
Removing the graphics card.........................................65
Prerequisites........................................................................................... 65
Procedure............................................................................................... 65
Replacing the graphics card......................................... 67
Procedure................................................................................................67
Post-requisites........................................................................................ 67
Removing the full-length graphics cards......................68
Prerequisites........................................................................................... 68
Procedure............................................................................................... 69
Replacing the full-length graphics cards.......................71
Procedure................................................................................................ 71
Post-requisites......................................................................................... 71
Removing the memory modules................................... 72
Prerequisites............................................................................................72
Procedure................................................................................................72
Replacing the memory modules....................................74
Procedure................................................................................................74
Post-requisites........................................................................................ 76
6
Removing the optical drive...........................................77
Prerequisites ...........................................................................................77
Procedure................................................................................................77
Replacing the optical drive........................................... 81
Procedure................................................................................................ 81
Post-requisites................................................................................... 81
Removing the power-button module............................ 82
Prerequisites............................................................................................82
Procedure................................................................................................82
Replacing the power-button module............................ 84
Procedure............................................................................................... 84
Post-requisites........................................................................................ 84
Removing the top I/O-panel........................................ 85
Prerequisites........................................................................................... 85
Procedure............................................................................................... 85
Replacing the top I/O-panel.........................................88
Procedure............................................................................................... 88
Post-requisites........................................................................................ 88
Removing blower and heat-sink assembly....................89
Prerequisites........................................................................................... 89
Procedure............................................................................................... 89
Replacing blower and heat-sink assembly.................... 93
Procedure............................................................................................... 93
Post-requisites........................................................................................ 93
7
Removing the processor fan and heat-sink assembly...95
Prerequisites........................................................................................... 95
Procedure............................................................................................... 95
Replacing the processor fan and heat-sink assembly... 97
Procedure................................................................................................97
Post-requisites.........................................................................................97
Removing the processor.............................................. 98
Prerequisites........................................................................................... 98
Procedure............................................................................................... 98
Replacing the processor............................................. 100
Procedure..............................................................................................100
Post-requisites.......................................................................................102
Removing the wireless card........................................ 103
Prerequisites.......................................................................................... 103
Procedure.............................................................................................. 103
Replacing the wireless card........................................ 105
Procedure..............................................................................................105
Post-requisites.......................................................................................106
Removing the antenna................................................ 107
Prerequisites.......................................................................................... 107
Procedure.............................................................................................. 107
Replacing the antenna.................................................110
Procedure...............................................................................................110
Post-requisites....................................................................................... 110
8
Removing the system board.........................................111
Prerequisites............................................................................................111
Procedure................................................................................................111
Replacing the system board........................................ 113
Procedure...............................................................................................113
Post-requisites........................................................................................113
Flashing the BIOS....................................................... 115
BIOS setup program....................................................116
BIOS overview........................................................................................116
Entering BIOS setup program.................................................................116
System Setup Options............................................................................116
Clearing forgotten passwords................................................................. 121
Prerequisites.....................................................................................121
Procedure........................................................................................ 122
Post-requisites.................................................................................124
Clearing CMOS settings........................................................................ 125
Prerequisites.................................................................................... 125
Procedure........................................................................................ 125
Post-requisites................................................................................. 127
Diagnostics.................................................................128
Getting help and contacting Dell.................................129
Self-help resources................................................................................ 129
Contacting Dell...................................................................................... 129
9
Before working inside your
computer
NOTE: The images in this document may dier from your computer
depending on the conguration you ordered.
Before you begin
1 Save and close all open les and exit all open applications.
2 Shut down your computer. Click Start → Power → Shut down.
NOTE: If you are using a dierent operating system, see the
documentation of your operating system for shut-down instructions.
3 Disconnect your computer and all attached devices from their electrical outlets.
4 Disconnect all attached network devices and peripherals, such as keyboard,
mouse, and monitor from your computer.
5 Remove any media card and optical disc from your computer, if applicable.
6 After the computer is unplugged, press and hold the power button for 5 seconds
to ground the system board.
Safety instructions
Use the following safety guidelines to protect your computer from potential damage
and ensure your personal safety.
WARNING: Before working inside your computer, read the safety
information that shipped with your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
WARNING: Disconnect all power sources before opening the computer
cover or panels. After you nish working inside the computer, replace all
covers, panels, and screws before connecting to the electrical outlet.
10
CAUTION: To avoid damaging the computer, ensure that the work surface is
at and clean.
CAUTION: To avoid damaging the components and cards, handle them by
their edges, and avoid touching pins and contacts.
CAUTION: You should only perform troubleshooting and repairs as
authorized or directed by the Dell technical assistance team. Damage due to
servicing that is not authorized by Dell is not covered by your warranty. See
the safety instructions that shipped with the product or at www.dell.com/
regulatory_compliance.
CAUTION: Before touching anything inside your computer, ground yourself
by touching an unpainted metal surface, such as the metal at the back of
the computer. While you work, periodically touch an unpainted metal surface
to dissipate static electricity, which could harm internal components.
CAUTION: When you disconnect a cable, pull on its connector or on its pull
tab, not on the cable itself. Some cables have connectors with locking tabs
or thumb-screws that you must disengage before disconnecting the cable.
When disconnecting cables, keep them evenly aligned to avoid bending any
connector pins. When connecting cables, ensure that the ports and
connectors are correctly oriented and aligned.
CAUTION: Press and eject any installed card from the media-card reader.
Recommended tools
The procedures in this document may require the following tools:
• Philips screwdriver
• Flat-head screwdriver
• Plastic scribe
11
Screw list
The following table provides the list of screws that are used for securing dierent
components to the computer.
Table 1. Screw list
Component Secured to Screw type Quantity Screw image
Hard drive Hard-drive
bracket
#6-32x1/4'' 4
Hard-drive
cage
Chassis #6-32x1/4'' 6 (two per
hard-drive
cage installed)
Power-supply
bracket
Chassis #6-32x1/4'' 2
Power-supply
unit
Chassis #6-32x1/4'' 4
Blower Heat-sink
assembly
#6-32x1/4'' 3
Chassis fan Chassis #6-32x1/4'' 1
Power button
module
Top panel #6-32x1/4'' 1
Solid-state
drive
System board M2x2.5 1
Wireless card System board M2x2.5 1
Top IO panel Chassis #6-32x1/4'' 4
ODD ODD bracket M2x2.5 1
12
Component Secured to Screw type Quantity Screw image
System board Chassis #6-32x1/4'' 8
13
After working inside your
computer
CAUTION: Leaving stray or loose screws inside your computer may severely
damage your computer.
1 Replace all screws and ensure that no stray screws remain inside your computer.
2 Connect any external devices, peripherals, or cables you removed before working
on your computer.
3 Replace any media cards, discs, or any other parts that you removed before
working on your computer.
4 Connect your computer and all attached devices to their electrical outlets.
5 Turn on your computer.
14
Technical overview
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
15
Inside view of your computer
1 chassis fan 2 memory module
3 optical drive 4 power-supply unit
5 front bezel 6 graphics card
7 system board 8 processor fan and heat-sink
assembly
16
System-board components
1 system board power connector
(ATX_POWER)
2 USB 2 (F_SSUSB2)
3 USB 1 (F_SSUSB1) 4 SATA 6 Gbps for hard drive
(SATA1)
5 SATA 6 Gbps for optical drive
(SATA2)
6 SATA 6 Gbps drive connector
(SATA3)
7 SATA 6 Gbps drive connector
(SATA4)
8 solid-state drive slot (M.2 SSD)
9 front I/O panel (F_PANEL) 10 media card reader connector
(CARD_READER)
17
11 CMOS-reset jumper (CMOS
JUMPER)
12 password-reset jumper
(PASSWORD JUMPER)
13 PCI-Express x16 card slot (SLOT1) 14 PCI-Express x1 card slots (SLOT 2
and SLOT 3)
15 PCI-Express x4 card slot (SLOT 4) 16 front audio connector (F_audio)
17 wireless-card slot (M.2_SLOT1) 18 CPU power cable (ATX_CPU)
19 chassis-fan connector (TOP_FAN) 20 processor socket
21 processor release latch 22 processor-fan connector
(CPU_FAN)
23 coin-cell battery (CMOS BATTERY) 24 memory-module slot (DIMM3)
25 memory-module slot (DIMM1) 26 memory-module slot (DIMM4)
27 memory-module slot (DIMM2)
18
Removing the right-side cover
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Place the computer in an upright position.
2 Pull the right-side cover release latch.
3 Lift the right-side cover and then slide it towards the top of the computer.
19
4 Remove the right-side cover from the chassis.
Figure 1. Removing the right-side cover
1 right-side cover release latch 2 chassis
3 right-side cover
20
Replacing the right-side cover
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
21
Procedure
Align the tabs on the right-side cover with the slots on the chassis and snap the
side-cover to lock it in place.
Figure 2. Right-side cover replacement
1slots 2 tabs
3 chassis 4 right-side cover
22
Removing the top cover
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
Remove the right-side cover.
Procedure
1 Place the computer in an upright position.
23
2 Pry the cover from the back corner and lift the top cover away from the chassis.
Figure 3. Removing the top cover
1top cover 2 chassis
24
Replacing the top cover
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
Align the tabs on the top cover with the slots on the top panel and press the top
cover until it snaps into place.
Post-requisites
Replace the right-side cover.
25
Removing the bottom cover
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
Remove the right-side cover.
Procedure
1 Place the computer with the bottom facing up.
26
2 Pry and lift the bottom cover away from the chassis.
Figure 4. Removing the bottom cover
1bottom cover 2 chassis
27
Replacing the bottom cover
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
Align the tabs on the bottom cover with the slots on the bottom panel and press
the bottom cover until it snaps in place.
Post-requisites
Replace the right-side cover.
28
Removing the front bezel
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
Remove the right-side cover.
29
Procedure
1 Pry the optical-drive bezel from the optical drive.
Figure 5. Removing the optical drive bezel
1optical-drive bezel 2 front bezel
2 Release the front-bezel tabs sequentially from the top, one at a time by moving
them away from the front chassis.
30
3 Rotate and pull the front bezel away from the front of the chassis to release the
front-bezel.
Figure 6. Removing the front bezel
1front-bezel tabs 2 front bezel
3 front chassis
31
Replacing the front bezel
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Align the tabs on the front bezel with the slots on the chassis.
2 Rotate the front bezel towards the chassis until the front bezel tabs snap into
place.
3 Snap the optical-drive bezel to the optical drive.
Post-requisites
Replace the right-side cover.
32
Removing the primary hard-drive
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
CAUTION: Hard drives are fragile. Exercise care when handling the hard
drive.
CAUTION: To avoid data loss, do not remove the hard drive while the
computer is in sleep or on state.
Prerequisites
Remove the right-side cover.
Procedure (with tabs)
1 Disconnect the data and power cables from the hard-drive.
33
2 Press the release tabs on the hard-drive carrier and slide the hard-drive carrier
out of the hard-drive cage.
Figure 7. Removing the hard-drive assembly
1data cable 2 power cable
3 hard-drive cage 4 release tabs
5 hard-drive carrier
3 Pry the hard-drive carrier to release the tabs on the carrier from the slots on the
hard drive.
34
4 Lift the hard drive o the hard-drive carrier.
NOTE: Note the orientation of the hard drive to replace it correctly.
Figure 8. Removing the hard drive from the bracket
1 hard drive 2 hard-drive carrier
3 tabs
35
Replacing the primary hard-drive
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
CAUTION: Hard drives are fragile. Exercise care when handling the hard
drive.
Procedure (with tabs)
1 Place the hard drive into the hard-drive carrier and align the tabs on the bracket
with the slots on the hard drive.
2 Snap the hard-drive carrier into the hard drive.
3 Slide the hard-drive carrier into the hard-drive cage until it snaps into place.
4 Connect the data and power cables to the hard-drive.
Post-requisites
Replace the right-side cover.
36
Removing the primary hard-drive
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
CAUTION: Hard drives are fragile. Exercise care when handling the hard
drive.
CAUTION: To avoid data loss, do not remove the hard drive while the
computer is in sleep or on state.
Prerequisites
Remove the right-side cover.
Procedure (with screws)
1 Disconnect the data and power cables from the hard drive.
37
2 Remove the screws that secure the hard-drive cage to the chassis.
Figure 9. Disconnecting cables
1#6-32x1/4'' screws (2) 2 hard drive
3 hard-drive cage 4 data cable
5 power cable
38
3 Lift the hard-drive cage o the chassis.
Figure 10. Removing the hard-drive cage
1 hard-drive cage 2 tab
3 hard-drive assembly
4 Remove the screws that secure the hard drive to the hard-drive cage.
39
5 Lift the hard drive o the hard-drive cage.
NOTE: Note the orientation of the hard drive to replace it correctly.
Figure 11. Removing the hard drive from the bracket
1#6-32 X 1/4'' screws (4) 2 hard drive
3 hard-drive cage
40
Replacing the primary hard-drive
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
CAUTION: Hard drives are fragile. Exercise care when handling the hard
drive.
Procedure
1 Place the hard drive into the hard-drive cage.
2 Align the screw holes on the hard-drive cage with the screw holes on the hard
drive.
3 Replace the screws that secure the hard drive to the hard-drive cage.
4 Insert the hard-drive cage into the chassis.
5 Replace the screws that secure the hard-drive cage to the chassis.
6 Connect the data and power cables to the hard drive.
Post-requisites
Replace the right-side cover.
41
Removing the secondary hard-
drive
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
CAUTION: Hard drives are fragile. Exercise care when handling the hard
drive.
CAUTION: To avoid data loss, do not remove the hard drive while the
computer is in sleep or on state.
Prerequisites
Remove the right-side cover.
Procedure
1 Disconnect the data and power cables from the hard drive.
42
2 Remove the screws that secure the hard-drive cage to chassis.
1 #6-32 X 1/4'' screws (2) 2 hard drive
3 hard-drive cage 4 power cable
5 data cable
43
3 Lift the hard drive cage o the chassis.
1 hard drive 2 hard-drive cage
4 Remove the screws that secure the hard drive to the hard-drive cage.
44
5 Lift the hard drive out of the hard drive cage.
NOTE: Note the orientation of the hard drive so that you can replace it
correctly.
1 #6-32 X 1/4'' screws (4) 2 hard drive
3 hard-drive cage
45
Replacing the secondary hard-
drive
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
CAUTION: Hard drives are fragile. Exercise care when handling the hard
drive.
Post-requisites
Replace the right-side cover.
Procedure
1 Place the hard drive into the hard-drive cage.
2 Replace the screws that secure the hard drive to the hard-drive cage.
3 Place the hard-drive cage into the hard-drive cage slot in the chassis.
4 Replace the screws that secure the hard-drive cage to the chassis.
5 Connect the data and power cables to the hard drive.
46
Removing the solid-state drive
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
CAUTION: Solid-state drives are fragile. Exercise care when handling the
solid-state drive.
CAUTION: To avoid data loss, do not remove the solid-state drive while the
computer is in sleep or on state.
Prerequisites
1 Remove the right-side cover.
2 Remove the full-length graphics card (if installed).
Procedure
1 Remove the screw that secures the solid-state drive to the system board.
47
Replacing the solid-state drive
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
CAUTION: Solid-state drives are fragile. Exercise care when handling the
solid-state drive.
Procedure
1 Align the notch on the solid-state drive with the tab on the solid-state drive slot.
2 Insert the solid-state drive at a 45-degree angle into the solid-drive drive slot.
For more information, see “System-board components”.
49
Removing the power-supply unit
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
Remove the right-side cover.
Procedure
NOTE: Note the routing of all cables as you remove them so that you can
reroute them correctly after you replace the power supply.
1 Slide the power-supply unit cage release latches towards the unlock position.
52
2 Rotate the power-supply unit cage away from the chassis.
Figure 14. Rotating the power-supply unit
1power-supply unit cage release
latches (2)
2 power-supply unit
3 chassis 4 power-supply unit cage
3 Disconnect the CPU-power cable and system board power cable from the
system board and the optical-drive power cable from the optical drive.
For more information, see “System-board components”.
4 Disconnect the graphics-card power cables if applicable.
53
5 Remove the system-board power cable from the routing guide on the chassis.
Figure 15. Disconnecting cables
1optical drive power cable 2 routing guide
3 CPU power cable 4 system board
5 system board power cable
6 Rotate the power-supply unit cage towards the chassis.
7 Disconnect the hard-disk power cable.
NOTE: There could be up to three hard-disk power cables depending on
the quantity of hard-disk drive installed.
8 Remove the screws that secure the power-supply bracket to the chassis.
9 Remove the screws that secure the power-supply unit to the chassis.
54
10 Lift the power-supply bracket o the chassis.
11 Lift the power-supply unit o the chassis.
Figure 16. Removing the power supply unit
1#6-32x1/4'' screws (4) 2 power-supply unit
3 power-supply bracket 4 #6-32x1/4'' screws (2)
5 hard-drive cable
55
Replacing the power-supply unit
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Place the power supply on the power-supply unit cage.
2 Replace the screws that secure the power-supply unit to the power-supply unit
cage.
3 Align the screw holes on the power-supply bracket with the screw holes on the
power-supply unit cage.
4 Replace the screws that secure the power supply bracket to the power-supply
unit cage.
5 Connect the hard-drive power cable.
6 Rotate the power-supply unit away from the chassis.
7 Connect the CPU-power cable, system-board power cable to the system board
and the optical-drive power cable to the optical drive.
For more information, see “System-board components”.
8 Route the system-board power cable through the routing guide on the chassis.
9 Connect the graphics-card power cables if applicable.
10 Rotate the power-supply unit towards the chassis until the unit snaps into place.
11 Slide the power-supply unit cage release latches to their locking positions to lock
the release latches.
Post-requisites
Replace the right-side cover.
56
Removing the coin-cell battery
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
CAUTION: Removing the coin-cell battery resets the BIOS setup program’s
settings to default. It is recommended that you note the BIOS setup
program’s settings before removing the coin-cell battery.
Prerequisites
1 Remove the right-side cover.
2 Follow the procedure from step 1 to step 2 in “Removing the power-supply unit”.
Procedure
1 Using a plastic scribe, press the battery-release lever away from the coin-cell
battery until the coin-cell battery pops up.
57
2 Lift the coin-cell battery out of its socket.
Figure 17. Removing the coin cell battery
1plastic scribe 2 coin-cell battery
3 coin-cell battery socket 4 battery-release lever
58
Replacing the coin-cell battery
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
Insert the coin-cell battery into the battery socket with the positive side facing up,
and snap the battery into place.
Post-requisites
1 Follow the procedure from step 9 to step 10 in “Replacing the power-supply
unit”.
2 Replace the right-side cover.
59
Removing the chassis fan
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the right-side cover.
2 Follow the procedure from step 1 to step 2 in “Removing the power-supply unit”.
3 Remove the blower and heat-sink assembly. (if installed)
Procedure
1 Remove the chassis-fan cable from the routing guide on the chassis-fan bracket.
2 Disconnect the chassis-fan cable from the system board.
For more information, see “System-board components”.
3 Remove the screw that secures the chassis-fan bracket to the chassis.
4 Slide the chassis-fan assembly towards the front of the computer to release the
fan from the chassis.
60
5 Lift the chassis-fan assembly o the chassis.
Figure 18. Removing the chassis fan
1routing guide 2 chassis-fan bracket
3 #6-32x1/4'' screw 4 chassis
5 chassis-fan cable 6 system board
7 chassis fan
6 Push the rubber grommets through the holes at each corner of the fan to
release the chassis-fan from the bracket.
61
7 Lift the chassis-fan o the chassis-fan bracket.
Figure 19. Removing the chassis fan
1 chassis-fan bracket 2 chassis-fan
62
Replacing the chassis fan
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Align the holes on the chassis fan with the rubber grommets on the chassis-fan
bracket.
NOTE: You must correctly align to the chassis-fan bracket to ensure
that the chassis fan is secured to the computer.
2 Insert the ends of the rubber grommets through the holes at each corner of the
fan.
3 Align the grommets in the fan with the holes at each corner of the chassis fan
bracket and pull through until they snap into place.
4 Route the chassis-fan cable through the routing guide on the bracket.
5 Align the tabs on the chassis-fan bracket with the slots on the chassis and slide
the fan into position.
6 Align the screw hole on the chassis-fan bracket with the screw hole on the
chassis.
7 Replace the screw that secures the chassis-fan bracket to the chassis.
8 Route the chassis-fan cable through the routing guide on the bracket.
9 Connect the chassis-fan cable to the system board.
For more information, see “System-board components”.
Post-requisites
1 Replace the blower and heat-sink assembly. (if installed)
2 Follow the procedure from step 9 to step 10 in “Replacing the power-supply
unit”.
63
Removing the graphics card
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
NOTE: Your computer will be shipped with either graphics card or full-length
graphics card.
1 Remove the right-side cover.
2 Follow the procedure from step 1 to step 2 in “Removing the power-supply unit”.
Procedure
1 Locate the graphics card on the system board and make note of the graphics-
card slot (PCI-Express x16).
For more information, see “System-board components”.
65
2 Push the securing tab on the PCIe slot away from the graphics card, grasp the
card by its top corner, and ease it out of the slot.
Figure 20. Removing the graphics card
1securing tab 2 system board
3 graphics card slot 4 graphics card
66
Replacing the graphics card
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Locate the PCI-Express x16 card slot on the system board.
For more information, see “System-board components”.
2 Align the notch on the graphics card with the tab on the slot and snap the
graphics card in place.
Post-requisites
1 Follow the procedure from step 9 to step 10 in “Replacing the power-supply
unit”.
2 Replace the right-side cover.
67
Removing the full-length
graphics cards
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
NOTE: Your computer will be shipped with either graphics card or full-length
graphics card.
1 Remove the right-side cover.
2 Follow the procedure from step 1 to step 2 in “Removing the power-supply unit”.
68
Procedure
1 Lift to release the graphics-card bracket from the chassis.
Figure 21. Removing the graphics-card bracket
1graphics-card bracket 2 chassis
2 Press the releasing clip on the power-cable connectors and disconnect the
power cables from the graphics card.
69
3 Push the securing tab on the PCIe slot away from the graphics card, grasp the
card by its top corner, and ease it out of the slot.
Figure 22. Removing the power cable
1power cables 2 releasing clips (2)
3 graphics card 4 securing tab
70
Replacing the full-length
graphics cards
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Align the full-length graphics card with the slot on the system board.
2 Place the card into the slot and press down rmly until the full-length graphics
card snaps into place.
3 Connect the power cables to the full-length graphics card.
4 Slide the tab on the graphics-card bracket into the slot on the chassis and snap it
into place.
Post-requisites
1 Follow the procedure from step 9 to step 10 in “Replacing the power-supply
unit”.
2 Replace the right-side cover.
71
Removing the memory modules
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the right-side cover.
2 Follow the procedure from step 1 to step 2 in “Removing the power-supply unit”.
Procedure
1 Locate the memory-module slot on the system board.
For more information, see “System-board components”.
2 Push the securing clips away from the memory module.
72
3 Grasp the memory module near the securing clip, and then gently ease the
memory module out of the memory-module slot.
CAUTION: If the memory module is dicult to remove, gently ease the
memory module back and forth to remove it from the slot.
NOTE: Repeat step 2 to step 3 to remove any other memory modules
installed in your computer.
Figure 23. Removing the memory module
1memory-module slot 2 memory module
3 securing clips (2) 4 system board 73
Replacing the memory modules
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Align the notch on the memory module with the tab on the memory-module slot.
74
2 Insert the memory module into the memory-module slot, and press the memory
module straight until it snaps into position and the securing clips lock in place.
NOTE: If you do not hear the click, remove the memory module and
reinstall it.
Figure 24. Replacing the memory module
1tab 2 notch
3 memory-module slot 4 memory module
5 system board 75
NOTE: Use slots DIMM1 and DIMM3 if you need to use two memory
modules. For more information, see System-board components.
The following table lists the available memory conguration matrix:
Table 2. Memory conguration matrix
Conguration Slot
DIMM1 DIMM2 DIMM3 DIMM4
8 GB 4 GB 4 GB
16 GB 8 GB 8 GB
24 GB 4 GB 4 GB 8 GB 8 GB
32 GB 8 GB 8 GB 8 GB 8 GB
64 GB 16 GB 16 GB 16 GB 16 GB
Post-requisites
1 Follow the procedure from step 9 to step 10 in “Replacing the power-supply
unit”.
2 Replace the right-side cover.
76
Removing the optical drive
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the right-side cover.
2 Follow the procedure from step 1 to step 2 in “Removing the power-supply unit”.
Procedure
1 Disconnect the power and data cables from the optical drive.
2 Pull the release tab on the optical-drive cage towards the bottom of the
computer.
77
3 Push to slide out the optical drive through the front of the computer.
Figure 25. Removing the optical drive
1power cable 2 data cable
3 optical drive 4 optical-drive cage
5 release tab
78
4 Push and slide the optical drive through the front of the computer.
Figure 26. Removing the optical drive
1optical-drive bezel 2 optical drive
3 front bezel
79
5 Remove the screw that secures the optical-drive bracket to the optical drive.
Figure 27. Removing the optical drive
1 M2x2.5 screw 2 optical-drive bracket
3 optical drive
80
Replacing the optical drive
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Align the screw hole on the optical-drive bracket with the screw hole on the
optical drive.
2 Replace the screw that secures the optical-drive bracket to the optical drive.
3 Replace the optical drive bezel.
4 Slide the optical drive into the optical-drive cage through the front of the
computer till it snaps into place.
5 Connect the power and data cables to the optical drive.
Post-requisites
1 Follow the procedure from step 9 to step 10 in “Replacing the power-supply
unit”.
2 Replace the right-side cover.
81
Removing the power-button
module
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the right-side cover.
2 Remove the top cover.
3 Remove the front bezel.
Procedure
NOTE: Note the routing of the cable as you remove it so that you can
reroute it correctly after you replace the power-button module.
1 Disconnect the power-button module cable from the system board.
For more information, see “System-board components”.
2 Note the power-button module cable routing and remove the cable from the
routing guides next to the system board on the chassis.
3 Remove the screw that secures the power-button module and lift the power-
button module from the chassis.
82
4 Remove the cable from the slot on top of the chassis.
Figure 28. Disconnect the power-button module cable
1system board 2 chassis
3 routing guide 4 #6-32x1/4'' screw
5 power-button module 6 power-button module cable
83
Replacing the power-button
module
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Route the cable through the slot on the top of the chassis.
2 Align the screw hole on the power-button module with the screw hole on the
chassis.
3 Replace the screw that secures the power-button module to the top chassis.
4 Route the power-button module cable through the routing guides on the chassis.
5 Connect the power-button module cable to the system board.
For more information, see “System-board components”.
Post-requisites
1 Replace the front bezel.
2 Replace the top cover.
3 Replace the right-side cover.
84
Removing the top I/O-panel
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the right-side cover.
2 Remove the front bezel.
3 Remove the top cover.
4 Follow the procedure from step 1 to step 2 in “Removing the power-supply unit”.
Procedure
1 Disconnect the top I/O-panel cables from the system board.
For more information, see "System-board components”.
2 Note the I/O-panel cables routing and remove them from the routing guides next
to the system board on the chassis.
85
3 Remove the cables through the slot at the top of the chassis.
Figure 29. Disconnecting the cables
1I/O-panel cables (2) 2 routing guide
3 chassis 4 top I/O panel bracket
4 Remove the screws that secure the top I/O-panel to the chassis.
86
5 Lift the top I/O-panel bracket from the chassis.
Figure 30. Removing the USB panel
1#6-32x1/4'' (4) 2 top I/O-panel bracket
3 chassis
87
Replacing the top I/O-panel
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Align the screw holes on the top I/O-panel with the screw holes on the chassis.
2 Replace the screws that secure the top I/O-panel to the top chassis.
3 Route the I/O-panel cables through the routing guides on the chassis.
4 Connect the top I/O-panel cables to the system board.
For more information, see "System-board components".
Post-requisites
1 Replace the top cover.
2 Replace the front bezel.
3 Follow the procedure from step 9 to step 10 in “Replacing the power-supply
unit”.
4 Replace the right-side cover.
88
Removing blower and heat-sink
assembly
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
WARNING: The heat sink may become hot during normal operation. Allow
sucient time for the heat sink to cool before you touch it.
CAUTION: For maximum cooling of the processor, do not touch the heat
transfer areas on the heat sink. The oils in your skin can reduce the heat
transfer capability of the thermal grease.
Prerequisites
1 Remove the right-side cover.
2 Follow the procedure from step 1 to step 2 in “Removing the power-supply unit”.
Procedure
1 Remove the screws that secure the blower to the heat-sink assembly.
89
2 Lift the blower o the heat-sink assembly and place it to the side.
Figure 31. Removing the blower
1#6-32x1/4'' screws (3) 2 blower
3 In a non-adjacent sequence, loosen the captive screws that secure the heat-sink
assembly to the system board.
90
4 Lift the heat-sink assembly o the system board.
Figure 32. Removing the captive screws
1heat-sink assembly 2 captive screws (4)
3 system board
91
Replacing blower and heat-sink
assembly
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
CAUTION: If either the processor or the heat-sink assembly is replaced, use
the thermal grease provided in the kit to make sure that thermal
conductivity is achieved.
NOTE: The original thermal grease can be reused if the original processor
and heat-sink assembly are reinstalled together.
1 Connect the blower cable to the system board.
For more information, see “System-board components”.
2 Place the heat-sink assembly over the processor.
3 Align the captive screws on the heat-sink assembly with the screw holes on the
system board.
4 In a non-adjacent sequence, tighten the captive screws that secure the heat-sink
assembly to the system board.
5 Place the blower over the heat-sink assembly.
6 Align the screw holes on the blower to the screw holes on the heat-sink
assembly.
7 Replace the screws that secure the blower to the heat-sink assembly.
Post-requisites
1 Follow the procedure from step 9 to step 10 in “Replacing the power-supply
unit”.
93
Removing the processor fan and
heat-sink assembly
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
WARNING: The heat sink may become hot during normal operation. Allow
sucient time for the heat sink to cool before you touch it.
CAUTION: For maximum cooling of the processor, do not touch the heat
transfer areas on the heat sink. The oils in your skin can reduce the heat
transfer capability of the thermal grease.
Prerequisites
1 Remove the right-side cover.
2 Follow the procedure from step 1 to step 2 in “Removing the power-supply unit”.
Procedure
1 Disconnect the processor-fan cable from the system board.
For more information, see “System-board components”.
2 In a non-adjacent sequence, loosen the captive screws that secure the processor
fan and heat-sink assembly to the system board.
95
3 Lift the processor fan and heat-sink assembly o the system board.
Figure 34. Removing the processor fan and heat sink
1processor-fan cable 2 captive screws (4)
3 processor fan and heat-sink
assembly
4 system board
96
Replacing the processor fan and
heat-sink assembly
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
CAUTION: If either the processor or the heat-sink assembly is replaced, use
the thermal grease provided in the kit to make sure that thermal
conductivity is achieved.
NOTE: The original thermal grease can be reused if the original processor
and heat-sink assembly are reinstalled together.
1 Place the processor fan and heat-sink assembly over the processor.
2 Align the captive screws on the processor fan heat-sink assembly with the screw
holes on the system board.
3 In a non-adjacent sequence, tighten the captive screws that secure the
processor fan and heat-sink assembly to the system board.
4 Connect the processor-fan cable to the system board.
For more information, see “System-board components”.
Post-requisites
1 Follow the procedure from step 9 to step 10 in “Replacing the power-supply
unit”.
2 Replace the right-side cover.
97
Removing the processor
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the right-side cover.
2 Follow the procedure from step 1 to step 2 in “Removing the power-supply unit”.
3 Remove the processor fan and heat-sink assembly.
4 Remove the blower and heat-sink assembly. (if installed)
Procedure
1 Press the processor release-lever down and then pull it outwards to release it
from the securing tab.
2 Extend the processor release-lever completely to open the processor cover.
98
3 Gently lift the processor and remove it from the processor socket.
Figure 35. Removing processor
1processor release-lever 2 securing tab
3 processor cover 4 processor socket
5 processor
99
Replacing the processor
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
CAUTION: If either the processor or the heat sink is replaced, use the
thermal grease provided in the kit to ensure that thermal conductivity is
achieved.
NOTE: A new processor ships with a thermal pad in the package. In some
cases, the processor may ship with the thermal pad attached to it.
Procedure
1 Ensure that the release lever on the processor socket is fully extended in the
open position.
CAUTION: The pin-1 corner of the processor has a triangle that aligns
with the triangle on the pin-1 corner on the processor socket. When the
processor is properly seated, all four corners are aligned at the same
height. If one or more corners of the processor are higher than the
others, the processor is not seated properly.
2 Align the pin-1 corner on the processor with the pin-1 corner on the processor
socket, and then place the processor in the processor socket.
3 When the processor is fully seated in the socket, close the processor cover.
100
4 Pivot the release-lever down and place it under the tab on the processor cover.
Figure 36. Replacing processor
1processor socket 2 processor
3 securing tab 4 processor cover
5 release lever
101
Removing the wireless card
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the right-side cover.
2 Follow the procedure from step 1 to step 2 in “Removing the power-supply unit”.
Procedure
1 Locate the wireless-card slot on the system board.
For more information, see “System-board components”.
2 Remove the screw that secures the wireless-card bracket to the wireless card
and the system board.
3 Remove the wireless-card bracket and disconnect the antenna cables from the
wireless card.
103
4 Slide and lift the wireless card o the system board.
Figure 37. Removing the wireless card
1 M2x2.5 screw 2 wireless-card bracket
3 antenna cables (2) 4 system board
5 wireless-card slot 6 wireless card
104
Replacing the wireless card
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
CAUTION: To avoid damaging the wireless card, do not place any cables
under it.
1 Align the notch on the wireless card with the tab on the wireless-card slot.
2 Slide the wireless card at an angle into the wireless-card slot.
3 Connect the antenna cables to the wireless card.
The following table provides the antenna-cable color scheme for the wireless
card supported by your computer.
Table 3. Antenna-cable color scheme
Connectors on the wireless card Antenna-cable color
Main (white triangle) White
Auxiliary (black triangle) Black
4 Align the screw hole on the wireless-card bracket with the screw hole on the
wireless card and the system board.
105
5 Replace the screw that secures the wireless-card bracket to the wireless card
and the system board.
Figure 38. Replacing the wireless card
1 wireless card 2 notch (2)
3 tab 4 system board
5 wireless card slot 6 wireless card bracket
7 antenna cables 8 M2x2.5 screw
Post-requisites
1 Follow the procedure from step 9 to step 10 in “Replacing the power-supply
unit”.
2 Replace the right-side cover.
106
Removing the antenna
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the right-side cover.
2 Follow the procedure from step 1 to step 2 in “Removing the power-supply unit”.
3 Remove the top cover.
4 Follow the procedure from step 1 to step 4 in Removing the wireless card.
Procedure
1 Open the securing clip which secures the antenna cable to the chassis.
2 Remove the cables from the routing guide through the slot on the top of the
chassis.
107
3 Note the antenna-cable routing and remove the antenna cables from the routing
guides on the chassis.
Figure 39. Disconnecting the antenna cables
1antenna cable 2 securing clip
3 chassis 4 routing guide
108
4 Using a plastic scribe, pry the antenna o the chassis.
Figure 40. Removing the antenna
1plastic scribe 2 antenna (2)
3 routing guide 4 chassis
5 antenna cables
109
Replacing the antenna
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Procedure
1 Adhere the antenna to the chassis.
2 Route the antenna cables through the slot on the top of the chassis.
3 Route the antenna cables through the routing guides on the chassis.
4 Secure the antenna cables to the chassis using the securing clip.
Post-requisites
1 Follow the procedure from step 3 to step 5 in “Replacing the wireless card”.
2 Replace the top cover.
3 Follow the procedure from step 9 to step 10 in “Replacing the power-supply
unit”.
4 Replace the right-side cover.
110
Removing the system board
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
NOTE: Your computer’s Service Tag is stored in the system board. You must
enter the Service Tag in the BIOS setup program after you replace the
system board.
NOTE: Replacing the system board removes any changes you have made to
the BIOS using the BIOS setup program. You must make the appropriate
changes again after you replace the system board.
NOTE: Before disconnecting the cables from the system board, note the
location of the connectors so that you can reconnect the cables correctly
after you replace the system board.
Prerequisites
1 Remove the right-side cover.
2 Follow the procedure from step 1 to step 2 in “Removing the power-supply unit”.
3 Follow the procedure from step 1 to step 3 in “Removing the antenna”.
4 Remove the memory modules.
5 Remove the graphics card.
6 Remove the solid-state drive.
7 Remove the wireless card.
8 Remove the processor fan and heat sink assembly.
9 Remove the processor.
Procedure
1 Disconnect all the cables connected to the system board.
For more information, see “System-board components”.
111
2 Make note of the cable routing and remove the cables from the routing guides.
3 Remove the screws that secure the system board to the chassis.
4 Lift the system board at an angle and remove it from the computer.
Figure 41. Removing the system board
1system board 2 #6-32x1/4'' screws (8)
3 chassis
112
Replacing the system board
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
NOTE: Your computer’s Service Tag is stored in the system board. You must
enter the Service Tag in the BIOS setup program after you replace the
system board.
NOTE: Replacing the system board removes any changes you have made to
the BIOS using the BIOS setup program. You must make the appropriate
changes again after you replace the system board.
Procedure
1 Slide the I/O ports on the system board into the slots on the chassis and align
the screw holes on the system board with the screw holes on the chassis.
2 Replace the screws that secure the system board to the chassis.
3 Route and connect the cables that you disconnected from the system board.
For more information, see “System-board components.”
Post-requisites
1 Replace the processor.
2 Replace the processor fan and heat sink assembly.
3 Replace the wireless card.
4 Replace the solid-state drive.
5 Replace the graphics card.
6 Replace the memory modules.
7 Follow the procedure from step 3 to step 4 in “Replacing the antenna”.
8 Follow the procedure from step 9 to step 10 in “Replacing the power-supply
unit”.
113
Flashing the BIOS
You may need to ash (update) the BIOS when an update is available or when you
replace the system board. To ash the BIOS:
1 Turn on your computer.
2 Go to www.dell.com/support.
3 Click Product support, enter the Service Tag of your computer, and then click
Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature
or manually browse for your computer model.
4 Click Drivers & downloads → Find it myself.
5 Select the operating system installed on your computer.
6 Scroll down the page and expand BIOS.
7 Click Download to download the latest version of the BIOS for your computer.
8 After the download is complete, navigate to the folder where you saved the BIOS
update le.
9 Double-click the BIOS update le icon and follow the instructions on the screen.
115
BIOS setup program
BIOS overview
CAUTION: Unless you are an expert computer user, do not change the
settings in the BIOS Setup program. Certain changes can make your
computer work incorrectly.
NOTE: Before you change BIOS Setup program, it is recommended that you
write down the BIOS Setup program screen information for future
reference.
Use the BIOS Setup program for the following purposes:
• Get information about the hardware installed in your computer, such as the
amount of RAM and the size of the hard drive.
• Change the system conguration information.
• Set or change a user-selectable option, such as the user password, type of hard
drive installed, and enabling or disabling base devices.
Entering BIOS setup program
1 Turn on (or restart) your computer.
2 During POST, when the DELL logo is displayed, watch for the F2 prompt to
appear, and then press F2 immediately.
NOTE: The F2 prompt indicates that the keyboard is initialized. This
prompt can appear very quickly, so you must watch for it, and then
press F2. If you press F2 before the F2 prompt, this keystroke is lost. If
you wait too long and the operating system logo appears, continue to
wait until you see the desktop. Then, turn o your computer and try
again.
System Setup Options
NOTE: Depending on your computer and its installed devices, the items
listed in this section may or may not appear.
116
Table 4. System setup options—Main menu
Main
System Date Displays the current date in mm/dd/
yyyy format.
System Time Displays the current time in hh:mm:ss
format.
BIOS Information
BIOS Version Displays the BIOS version number.
Product Information
Product Name Displays the product name.
Service Tag Allows you to enter the service tag of
your computer.
Asset Tag Displays the asset tag of your
computer.
Memory Information
System Memory Displays the total computer memory
installed.
Memory Speed Displays the memory speed.
CPU Information
Processor Type Displays the processor type
Processor ID Displays the processor identication
code.
CPU Speed Displays the speed of the processor.
Cache L1 Displays the processor L1 cache size.
Cache L2 Displays the processor L2 cache size.
Cache L3 Displays the processor L3 cache size.
117
Table 5. System setup options—Advanced menu
Advanced
Advanced BIOS Features
Intel SpeedStep Technology Allows you to enable or disable Intel
Speedstep Technology. Default: Enabled.
NOTE: If enabled, the processor
clock speed and core voltage are
adjusted dynamically based on the
processor load.
Intel Virtualization Technology Allows you to enable or disable Intel
Virtualization Technology feature for the
processor.
VT for Direct I/O Allows you to enable or disable Intel
Virtualization Technology feature for the
Direct I/O.
SATA Operation Allows you to congure the operating
mode of the integrated SATA hard drive
controller.
Intel Ready Mode Technology Allows you to enable or disable the Intel
Ready Mode Technology.
Intel Software Guard Extensions Allows you to enable or disable Intel
Software Guard Extensions.
BIOS Recovery from Hard Drive Allows you to enable or disable BIOS
Recovery from hard drive.
USB Conguration
Front USB Ports Allows you to enable or disable the front
USB ports.
Rear USB Ports Allows you to enable or disable the rear
USB ports.
Power Options
Numlock Key Allows you to set the status of the Num
Lock key during boot to On or O.
Wake Up by Integrated LAN Allow the computer to be powered on by
special LAN signals.
118
Advanced
AC Recovery Sets what action the computer takes
when power is restored.
Deep Sleep Control Allows you to dene the controls when
Deep Sleep is enabled.
USB Wake Support (S3) Allows you to enable the USB devices to
wake the computer from Standby.
USB PowerShare (S4/S5) Allows you to charge external devices.
USB PowerShare Wake Support
(S4/S5)
Allows you to enable USB devices to
wake the computer from S4/S5.
Auto Power On
Auto Power On Mode Allows you to set the computer to turn
on automatically every day or on a
preselected date. This option can be
congured only if the Auto Power On
mode is set to Enabled Everyday or
Selected Day.
Auto Power On Date Allows you to set the date on which the
computer must turn on automatically.
This option can be congured only if the
Auto Power On mode is set to Enabled 1
to 31.
Auto Power On Time Allows you to set the time at which the
computer must turn on automatically.
This option can be congured only if the
Auto Power On mode is set to Enabled
hh:mm:ss.
Performance Options
Overclocking Feature
Core Over Clocking Level Allows you enable or disable the
processor to adjust the ex ratio and
voltage in a turbo mode environment.
Core Ratio Limit Override Allows you to set the core ratio limit.
Single Core Allows you to select single core or
multiple cores.
119
Advanced
Core Voltage Mode Allows you to select between adaptive
and override voltage modes.
Core Voltage Oset Allows you to set the override value of
core voltage.
Long Duration PWR Limit Allows you to set the turbo mode power
limit.
Short Duration PWR Limit
Options
Allows you to set the turbo mode power
limit.
Table 6. System setup options—Security menu
Security
Admin Password Status Displays whether the admin password
is set.
System Password Status Displays whether the system password
is set.
HDD Password Status Displays if the hard drive password is
set.
Admin Password Displays the admin password.
System Password Displays the system password.
HDD Password Displays the hard drive password.
Firmware TPM Displays the rmware TPM.
Table 7. System setup options—Boot menu
Boot
Boot List Option Displays the available boot devices.
File Browser Add Boot Option Allows you to set the boot path in the
boot option list.
File Browser Del Boot Option Allows you to delete the boot path in
the boot option list.
Secure Boot Control Allows you to enable or disable the
secure boot control.
120
Boot
Load Legacy OPROM Allows you to enable or disable the
Legacy Option ROM.
Boot Option Priorities Displays the available boot devices.
Boot Option #1 Displays the rst boot device. Default:
UEFI: Windows Boot Manager.
Boot Option #2 Displays the second boot device.
Default: Onboard NIC Device.
Boot Option #3 Displays the third boot device. Default:
Onboard NIC Device.
Table 8. System setup options—Exit menu
Save & Exit
Save Changes and Reset Allows you to exit system setup and
save your changes.
Discard Changes and Reset Allows you to exit system setup and
load previous values for all system
setup options.
Restore Defaults Allows you to load default values for all
system setup options.
Discard Changes Allows you to exit your changes.
Save Changes Allows you to save your changes.
Clearing forgotten passwords
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the right side-cover.
121
2 Remove the jumper plug from the password jumper-pins.
Figure 42. Removing the jumper plug
1jumper plug
3 Power on without the jumper plug to clear the password.
123
2 Follow the procedure from step 9 to step 10 in “Replacing the power-supply
unit”.
Clearing CMOS settings
WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in Before
working inside your computer. After working inside your computer, follow
the instructions in After working inside your computer. For more safety best
practices, see the Regulatory Compliance home page at www.dell.com/
regulatory_compliance.
Prerequisites
1 Remove the right side-cover.
2 Follow the procedure from step 1 to step 3 in “Removing the power-supply unit”.
Procedure
1 Locate the CMOS reset jumper (CMCLR) on the system board.
NOTE: For more information on the location of the CMOS jumper, see
“System-board components”.
2 Remove the power cord.
3 Remove the jumper plug from the password jumper-pins (PSWD) and connect it
to the CMOS jumper-pins.
125
4 Wait for 5 seconds and then replace the jumper plug to the password jumper-
pins (PSWD).
Figure 44. Clearing the CMOS
1jumper plug 2 CMOS jumper-pins
3 password jumper-pins (PSWD)
126
Diagnostics
The computer POST (Power On Self Test) ensures that it meets the basic computer
requirements and the hardware is working appropriately before the boot process
begins. If the computer passes the POST, the computer continues to start in a normal
mode. However, if the computer fails the POST, the computer emits a series of LED
codes during the start-up. The system LED is integrated on the Power button.
The following table shows dierent light patterns and what they indicate.
Table 9. Diagnostics
Number of LED ashes Problem description
1System board: BIOS and ROM failure
2No memory or RAM detected
3System board or chipset error
4Memory or RAM failure
5CMOS battery failure
6Video card or chip failure
7CPU failure
3,6 Recovery image not found
3,7 Recovery image found but invalid
128
Getting help and contacting Dell
Self-help resources
You can get information and help on Dell products and services using these self-help
resources:
Table 10. Self-help resources
Information about Dell products and
services
www.dell.com
Dell Help & Support app
Get started app
Accessing help In Windows search, type Help and
Support, and press Enter.
Online help for operating system www.dell.com/support/windows
www.dell.com/support/linux
Troubleshooting information, user
manuals, setup instructions, product
specications, technical help blogs,
drivers, software updates, and so on.
www.dell.com/support
Learn about your operating system,
setting up and using your computer, data
backup, diagnostics, and so on.
See Me and My Dell at www.dell.com/
support/manuals.
Contacting Dell
To contact Dell for sales, technical support, or customer service issues, see
www.dell.com/contactdell.
129
NOTE: Availability varies by country and product, and some services may
not be available in your country.
NOTE: If you do not have an active internet connection, you can nd
contact information on your purchase invoice, packing slip, bill, or Dell
product catalog.
130